
August 2004
www.lexmark.com
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. © 2004 Lexmark International, Inc. 740 West New Circle Road Lexington, Kentucky 40550

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time. Comments about this publication may be addressed to Lexmark International, Inc., Department F95/032-2, 740 West New Circle Road, Lexington, Kentucky 40550, U.S.A. In the United Kingdom and Eire, send to Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. You can purchase additional copies of publications related to this product by calling 1-800-553-9727. In the United Kingdom and Eire, call +44 (0)8704 440 044. In other countries, contact your point of purchase. References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility. Lexmark, Lexmark with diamond design, MarkNet, MarkVision, and Optra are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. ColorGrade, PerfectFinish, and PictureGrade are trademarks of Lexmark International, Inc. The following terms are trademarks or registered trademarks of other companies:
Albertus The Monotype Corporation plc Antique Olive Monsieur Marcel OLIVE Apple-Chancery Apple Computer, Inc. Arial The Monotype Corporation plc Candid Agfa Corporation CG Omega Product of Agfa Corporation CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Agfa Corporation Chicago Apple Computer, Inc. Clarendon Linotype-Hell AG and/or its subsidiaries Eurostile Nebiolo Geneva Apple Computer, Inc. GillSans The Monotype Corporation plc Helvetica Linotype-Hell AG and/or its subsidiaries Hoefler Jonathan Hoefler Type Foundry ITC Avant Garde Gothic International Typeface Corporation
ITC Bookman International Typeface Corporation ITC Lubalin Graph International Typeface Corporation ITC Mona Lisa International Typeface Corporation ITC Zapf Chancery International Typeface Corporation Joanna MT The Monotype Corporation plc Marigold Arthur Baker Monaco Apple Computer, Inc. New York Apple Computer, Inc. Oxford Arthur Baker Palatino Linotype-Hell AG and/or its subsidiaries Stempel Garamond Linotype-Hell AG and/or its subsidiaries Taffy Agfa Corporation Times New Roman The Monotype Corporation plc TrueType Apple Computer, Inc. Univers Linotype-Hell AG and/or its subsidiaries Wingdings Microsoft Corporation
AppleTalk, EtherTalk, LocalTalk, and Macintosh are trademarks of Apple Computer, Inc., registered in the United States and other countries. PCL® is a registered trademark of the Hewlett-Packard Company. PCL 3, PCL 5, and PCL 6 are Hewlett-Packard Company’s designations of a set of printer commands (language) and functions included in its printer products. These printers are intended to be compatible with the PCL 3, PCL 5, and PCL 6 languages. This means these printers recognize PCL 3, PCL 5, and PCL 6 commands used in various application programs, and that the printer emulates the functions corresponding to the commands. PostScript® is a registered trademark of Adobe Systems Incorporated. PostScript is Adobe Systems’ designation of a set of printer commands (language) and functions included in its software products. These printers are intended to be compatible with the PostScript language. This means these printers recognize PostScript commands used in various application programs, and that the printer emulates the functions corresponding to the commands. Other trademarks are the property of their respective owners. Safety Information
© 1998, 2004 Lexmark International, Inc. All rights reserved. UNITED STATES GOVERNMENT RIGHTS This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.


CHAPTER 1: Introduction
Overview
The following edition of the Technical Reference contains information about printer commands and printer languages supported by the following Lexmark printers:
To determine which commands and languages your printer supports, see the appendixes in the back of this document or refer to your printer user documentation.
If your printer is not included in this edition of the Technical Reference, it may be available in another version. Visit the Lexmark Web site at www.lexmark.com/ publications for more information.

Printed documentation is also available for some Lexmark printers. Obtain the correct part number from the following table, call 1-800-553-9727, and select option #1 to order a Technical Reference for your printer.
The Technical Reference is divided into the following:
Shows how to select PCL emulation and discusses PCL emulation commands, GL/2 commands, and resident font and symbol set support.
Contains detailed information about certain commands that cause the printer to enter PCL emulation, PostScript emulation, and Personal Printer Data Stream (PPDS), and many other types of commands.
Provides information about PostScript emulation and explains PostScript emulation supplemental operators.
Describes ways to switch printer languages and explains when you may want to choose one method over another.
Provides information about using the flash memory and hard disk. It describes how to manage printer memory, store resources (such as fonts and macros), and manage files.

Lists printer specifications, including information about hardware and environmental conditions.
Provides information on printer interfaces, including information about parallel and serial interface, network support, and communication protocols.
See the tables in the three appendixes to determine if your printer supports a particular PCL emulation, PJL, or PostScript emulation command. The appendixes are:
Appendix B: “PJL Support”
Appendix C: “PostScript Support”

Navigational Tips
If you are not familiar with PDF files, the following tips may help you find the information you need.
– Select an option under View in the menu bar at the top of the page. – Use the arrows in the toolbar at the top of the page, or the up arrow and
down arrow keys on the keyboard. – Press the Page Up and Page Down keys on the keyboard. – Use the scroll bar to the right of the page. – Click the page number box on the status bar at the bottom of the page and
type the page you want. • To increase or decrease the magnification of the pages:
– Select the magnifying glass icon on the toolbar at the top of the page and
then draw a box around the area you want to view. – Click the magnification box on the status bar and select an option from the
drop-down menu. • To jump directly to a particular section or key word in this document:
– Click one of the bookmarks in the overview window to the left of the page. – Click a topic in the document’s table of contents. – Select Tools from the menu bar and then choose Find or Search. – Click the binoculars icon on the toolbar and then type a word in the text box. – Click a cross-reference to a figure, page number, or heading in the docu-
ment itself.
Although this book was designed primarily for online viewing, you can print a hard copy by clicking File on the toolbar, and then choosing Print. Make sure you’ve selected the correct printer, range of pages, and number of copies before you click OK. You should be aware that if you print this document on a color printer, the color you see on the paper may not match the color you see on your computer monitor.

Bibliography
For detailed information about PCL emulation printer commands, PostScript emulation printer commands and operators, and interfaces, refer to the following documentation:

CHAPTER 2: PCL Emulation
When you select PCL emulation as the printer language, the printer supports the Hewlett-Packard Company’s LaserJet Printer Command Language. This chapter shows how to select PCL emulation and discusses PCL emulation commands, along with resident PCL emulation font and symbol set support.
To determine which commands your printer supports, see Appendix A: “PCL Support” on page A-1.
Using SmartSwitch
When SmartSwitch is enabled for both printer languages on an interface (for example, Parallel, USB, Serial Option 1, or Network Option 1), the printer automatically switches to the printer language being sent by your software program. The printer is shipped with SmartSwitch enabled for both printer languages in all interfaces. The printer examines all print jobs and switches dynamically between PostScript emulation and PCL emulation.
If SmartSwitch is set to Off for both printer languages, you can select PCL emulation from your printer operator panel or from MarkVision™ Professional. Refer to your printer user documentation for information on changing menu settings.

Using Your Software Program
To select PCL emulation, use the Printer Job Language (PJL) Enter Language Command. See “ENTER LANGUAGE Command” on page 3-3 for more information. See “Printer Job Language” on page 3-1 for the syntax and use of PJL.
downloaded resources, unless Resource Save is set to On or the resources are stored in flash memory or on disk.

Page Formatting
The printable areas and logical pages for PCL emulation (both portrait and landscape orientation) are illustrated below. See the Legend that follows for definitions of areas A through I.

A Portrait physical page width and landscape physical page length
B Portrait physical page length and landscape physical page width
C Portrait logical page width
D Landscape logical page width
E Distance between the side edge of the physical page and the logical page in portrait
F Distance between the side edge of the physical page and the logical page in landscape
G Distance between the top and bottom edge of the physical page and logical page
H Distance between the left and right edge of the physical page and the printable area in portrait, or distance between the top and bottom edge of the physical page and printable area in landscape
I Distance between the top and bottom edge of the physical page and the printable area in portrait, or distance between the left and right edge of the physical page and the printable area in landscape
area labeled on the preceding diagram for all paper and envelope sizes your printer supports. If information about your printer is not included in the following tables, see page 1-1 for information on how to get a Technical Reference for your printer.

Lexmark C510(n)
The following table lists page sizes and print area dimensions for all paper and envelope sizes the Lexmark C510(n) printer supports. For more information about the printable areas and logical pages for PCL emulation, see “Printable Areas” on page 2-3.
Selection Paper/Envelope Dimensions Dimensions by Area (pels)1
Page Size Parm2 Name mm inches A B C D E F G H I
13, 613 A5 148 x 210 5.83 x 8.27 3496 4960 3196 4720 142 118 0 100 100
12, 45, 612 JIS B5 Paper 182 x 257 7.2 x 10.1 4300 6070 4000 5830 150 120 0 100 100
26, 626 A4 (198 mm)3 210 x 297 8.3 x 11.7 4960 7014 4676 6778 142 118 0 80 80
26, 626 A4 (203 mm)3 210 x 297 8.3 x 11.7 4960 7014 4800 6778 80 118 0 80 80
1, 601 Executive 184 x 267 7.25 x 10.5 4350 6300 4050 6060 150 120 0 100 100
2, 602 Letter 216 x 279 8.5 x 11 5100 6600 4800 6360 150 120 0 100 100
3, 603 Legal5 216 x 356 8.5 x 14 5100 8400 4800 8160 150 120 0 100 100
4 or 10 Folio5 216 x 330 8.5 x 13 5100 7800 4800 7560 150 120 0 100 100
15 Statement 139.7 x 215.9 5.5 x 8.5 3300 5100 3000 4860 150 120 0 100 100
101 Universal5 216 x 356 8.5 x 14 5100 8500 4800 8260 150 120 0 100 100
90 DL 220 x 110 8.66 x 4.33 2598 5196 2314 4960 142 118 0 100 100
91 C5 229 x 162 9.02 x 6.38 3826 5408 3542 5172 142 118 0 100 100
994, 100 B5 Envelope 250 x 176 9.84 x 6.93 4156 5904 3872 5668 142 118 0 100 100
600 Other Envelope5 216 x 356 8.5 x 14 5100 8400 4800 8160 150 120 0 100 412
89 9 (Com 9) 225 x 98 8.875 x 3.875 2326 5324 2024 5084 150 120 0 100 100
81 10 (Com 10) 241 x 105 9.5 x 4.125 2474 5700 2174 5460 150 120 0 100 100
1 Pel dimensions are for 600 dpi. 2 Page Size Parameters are explained in Table 2-30 on page 2-64. 3 The width of the logical page for A4 paper can be changed from the printer operator panel or your software application. 4 Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039. 5 The Lexmark C510(n) supports this size media only with an optional legal tray.
to Normal. For more information about Print Area, see page 2-6.
Paper · Envelope

Lexmark X422
The following table lists page sizes and print area dimensions for all paper and envelope sizes the Lexmark X422 printer supports. For more information about the printable areas and logical pages for PCL emulation, see “Printable Areas” on page 2-3.
Selection Paper/Envelope Dimensions Dimensions by Area (pels)1
Page Size Parm2 Name mm inches A B C D E F G H I
13, 613 A5 148 x 210 5.83 x 8.27 3496 4960 3196 4720 142 118 0 100 100
12, 45, 612 JIS B5 Paper 182 x 257 7.2 x 10.1 4300 6070 4000 5830 150 120 0 100 100
26, 626 A4 (198 mm)3 210 x 297 8.3 x 11.7 4960 7014 4676 6778 142 118 0 80 80
26, 626 A4 (203 mm)3 210 x 297 8.3 x 11.7 4960 7014 4800 6778 80 118 0 80 80
1, 601 Executive 184 x 267 7.25 x 10.5 4350 6300 4050 6060 150 120 0 100 100
2, 602 Letter 216 x 279 8.5 x 11 5100 6600 4800 6360 150 120 0 100 100
3, 603 Legal 216 x 356 8.5 x 14 5100 8400 4800 8160 150 120 0 100 100
4 or 10 Folio 216 x 330 8.5 x 13 5100 7800 4800 7560 150 120 0 100 100
15 Statement 139.7 x 215.9 5.5 x 8.5 3300 5100 3000 4860 150 120 0 100 100
101 Universal 216 x 356 8.5 x 14 5100 8500 4800 8260 150 120 0 100 100
90 DL 220 x 110 8.66 x 4.33 2598 5196 2314 4960 142 118 0 100 100
91 C5 229 x 162 9.02 x 6.38 3826 5408 3542 5172 142 118 0 100 100
994, 100 B5 Envelope 250 x 176 9.84 x 6.93 4156 5904 3872 5668 142 118 0 100 100
600 Other Envelope 229 x 356 9.02 x 14 5100 8400 4800 8160 150 120 0 100 100
80 7-3/4 Monarch 191 x 98 7.5 x 3.875 2326 4500 2024 4260 150 120 0 100 100
89 9 (Com 9) 225 x 98 8.875 x 3.875 2326 5324 2024 5084 150 120 0 100 100
81 10 (Com 10) 241 x 105 9.5 x 4.125 2474 5700 2174 5460 150 120 0 100 100
1 Pel dimensions are for 600 dpi. 2 Page Size Parameters are explained in Table 2-30 on page 2-64. 3 The width of the logical page for A4 paper can be changed from the printer operator panel or your software application. 4 Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039.
to Normal. For more information about Print Area, see page 2-6.
Paper · Envelope

Lexmark E230, E232, E234(n), E330, E332n
The following table lists page sizes and print area dimensions for all paper and envelope sizes the Lexmark E230, E232, E234(n), E330, and E332n printer supports. For more information about the printable areas and logical pages for PCL emulation, see “Printable Areas” on page 2-3.
Paper/Envelope Dimensions Dimensions by Area (pels)1
Page Size Parm2 Name mm inches A B C D E F G H I J K L
13, 613 A5 148 x 210 5.83 x 8.27 3496 4960 3196 4720 142 118 0 100 300
12, 45, 612 JIS B5 Paper 182 x 257 7.2 x 10.1 4300 6070 4000 5830 150 120 0 100 300
26, 626 A4 (198 mm)3 210 x 297 8.3 x 11.7 4960 7014 4676 6778 142 118 0 80 80 100 100 300
26, 626 A4 (203 mm)3 210 x 297 8.3 x 11.7 4960 7014 4800 6778 80 118 0 80 80 100 100 300
1, 601 Executive 184 x 267 7.25 x 10.5 4350 6300 4050 6060 150 120 0 100 300
2, 602 Letter 216 x 279 8.5 x 11 5100 6600 4800 6360 150 120 0 100 300
3, 603 Legal 216 x 356 8.5 x 14 5100 8400 4800 8160 150 120 0 100 300
4 or 10 Folio 216 x 330 8.5 x 13 5100 7800 4800 7560 150 120 0 100 300
15 Statement 139.7 x 215.9 5.5 x 8.5 3300 5100 3000 4860 150 120 0 100 300
101 Universal 216 x 356 8.5 x 14 5100 8500 4800 8260 150 120 0 100 300
90 DL 220 x 110 8.66 x 4.33 2598 5196 2314 4960 142 118 0 100 300
91 C5 229 x 162 9.02 x 6.38 3826 5408 3542 5172 142 118 0 100 300
994, 100 B5 Envelope 250 x 176 9.84 x 6.93 4156 5904 3872 5668 142 118 0 100 300
216 x 356 8.5 x 14 5100 8400 4800 8160 150 120 0 100 412 100 100 300
89 9 (Com 9) 225 x 98 8.875 x 3.875 2326 5324 2024 5084 150 120 0 100 300
81 10 (Com 10) 241 x 105 9.5 x 4.125 2474 5700 2174 5460 150 120 0 100 300
1 Pel dimensions are for 600 dpi. 2 Page Size Parameters are explained in Table 2-30 on page 2-64. 3 The width of the logical page for A4 paper can be changed from the printer operator panel or your software application. 4 Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039.
to Normal. For more information about Print Area, see page 2-6.

Print Area Menu Item
The printable area is the area on a sheet of paper within which a pel can be printed. Logical page is a conceptual entity that defines the area in which margins (top, bottom, left, right) may be set and the area in which the PCL cursor may be positioned.
The physical page border is the actual physical boundaries of a page.
The Print Area menu item is available from the printer operator panel or through MarkVision Professional. For some printers, Print Area supports three values: Normal, Whole Page, and Fit to Page. Refer to your printer user documentation for more information.
Normal setting Whole Page setting
Legend:
PCL Logical Page Area
Only Portrait Orientation shown for all settings
The Normal setting, which is the factory default, means the printable area includes the entire page except the narrow border around the edge of the page. This is the nonprintable area. The printer measures margin settings relative to the logical page.
For a more detailed explanation of the Normal setting, see “Printable Areas” on page 2-3.
Physical Page Border · PCL Printable Area

The Whole Page setting only affects pages printed when using PCL emulation. If Whole Page is selected, the PCL language sets the logical page area equal to the physical page dimensions. Since the logical page dimensions and the physical page dimensions are the same, in theory, the cursor may be positioned anywhere on the page. However, the PCL language clips the image to the printable area. So, the Whole Page setting is useful for printing scanned images that extend from edge to edge of a page.
Some printers offer the Fit to Page setting. When Fit to Page is selected, PCL emulation or PostScript emulation formats a page using a printable area equal to the physical page, which is from one edge of the page to the other edge of the page. If you use this setting, no clipping occurs. In Fit to Page, the PCL emulation logical page dimensions are equal to the physical page dimensions, as in the Whole Page setting.
The printer holds this formatted image in memory, but when the page prints, the image is compressed a small amount in both horizontal and vertical directions, and then centered on the physical page for letter-size paper only. This process creates a small margin around the image. This artificial margin prevents printing from one edge to the other, since doing so could contaminate the printer and cause printing problems.
The following illustrations show an image held in memory for printing from one edge to the other and how the image would actually print based on the Fit to Page setting. Notice that a small border appears at the edges of the printed page, and the image is slightly compressed.
Formatted Image with Fit to Page Printed Image with Fit to Page
Physical Page Edge

Font and Symbol Set Support for the Lexmark X422
Your printer has 91 resident fonts in PCL emulation, including 89 scalable fonts and two bitmapped fonts.
Several parameters are used to select a font from the data stream. These include symbol set, spacing, point or pitch, style, weight, and typeface number. For scalable fonts, you can vary the size of a font by specifying pitch or point size. For bitmapped fonts, you must choose the pitch or point size listed on the font sample pages. You can print the font sample pages from the MFP control panel, using a PJL command (see “LPRINTPCLFONTS” on page 3-83.) or through MarkVision Professional. Refer to your printer user documentation for more information.
A symbol set defines which characters are available for a font and the code point for each of these characters. Your printer supports 88 symbol sets. The tables beginning on page 2-15 show the symbol sets available for each font in PCL emulation. Not all fonts support all symbol sets.
You can select a font as the PCL emulation default from the MFP control panel or through MarkVision Professional. Refer to your printer user documentation for more information.
The fonts are divided into three major groups. The first 47 fonts (R0 through R46) shown on the font sample pages are the standard PCL emulation fonts. The next 39 fonts (R47 through R85) are called Type 1 fonts and were originally defined for PostScript emulation, but now also work in the PCL emulation. The last five fonts (R86 through R90) include three different Code 3 of 9 bar code fonts, OCR-A and OCR-B fonts.
The fonts are further divided into font groups A, B, and C indicating which symbol sets are supported by each font. For a list of the 47 standard PCL emulation fonts, as well as the OCR and Code 3 of 9 bar code fonts, see Table 2-4 on page 2-10. For a list of the 39 Type 1 fonts, see Table 2-5 on page 2-13. Both tables list the forward and backward compatibility font selection commands and the font group (A, B, or C) for each font. For more information on forward and backward compatibility, see page 2-10. For more information on selecting symbol sets, see page 2-15.
For compatibility purposes, you can disable Type 1 fonts with the Printer Job Language (PJL) LTYPE1FONTS command. The factory default for these fonts is Enabled. See LTYPE1FONTS on page 3-47 for more information.

You can also select fonts using PJL commands. The selection parameter is the number portion from the font identifier shown on the font sample pages, such as 0 or 76 from font identifiers R0 or R76. Use the PJL values shown in the tables beginning on page 2-15 to select a symbol set. If a symbol set does not have a PJL value, use the symbol set ID to select the symbol set. A font selection can be either temporary or set as the default.
Use the following PJL commands to select fonts: FONTSOURCE, FONTNUMBER, PITCH, PTSIZE, SYMSET, SET, DEFAULT. See Table 3-5: “Common Variables for PCL Emulation” on page 3-48 for more information about these commands.
Your PCL emulation has forward and backward compatibility modes. The forward compatibility mode is used to emulate the fonts in the Hewlett-Packard Company’s LaserJet 4050. The backward compatibility mode is used for compatibility with the Hewlett-Packard Company’s LaserJet 5 and the Lexmark family of printers.
Standard PCL Emulation Fonts, OCR and Code 3 of 9 bar code fonts
Table 2-4 on page 2-10 lists the font selection commands for forward and backward compatibility mode for each of the 47 standard PCL emulation fonts, the OCR and Code 3 of 9 bar code fonts. Since the font selection commands for the forward and backward compatibility modes are identical, they are listed together in the table. Most fonts are assigned a font group indicating which symbol sets that font supports.
To determine which symbol sets are supported by a particular font, find the font group (A, B, or C) for the font in Table 2-4, and then see Table 2-6 on page 2-15 for the symbol sets that belong to that group.
Forward and Backward Compatibility Mode Font Group Style Bold Typeface
Standard PCL Emulation Font Name
Courier 0 0 4099 A
Courier Italic 1 0 4099 A
Courier Bold 0 3 4099 A
Courier Bold Italic 1 3 4099 A
1 For the symbol sets supported by this font, see Table 2-7: “Non-Text PCL Emulation Symbol Sets” on page 2-17.

Forward and Backward Compatibility Mode Font Group Style Bold Typeface
Standard PCL Emulation Font Name
CG Times 0 0 4101 A
CG Times Italic 1 0 4101 A
CG Times Bold 0 3 4101 A
CG Times Bold Italic 1 3 4101 A
Univers Medium 0 0 4148 A
Univers Medium Italic 1 0 4148 A
Univers Bold 0 3 4148 A
Univers Bold Italic 1 3 4148 A
Letter Gothic 0 0 4102 B
Letter Gothic Italic 1 0 4102 B
Letter Gothic Bold 0 3 4102 B
Univers Condensed Medium 4 0 4148 B
Univers Condensed Medium Italic 5 0 4148 B
Univers Condensed Bold 4 3 4148 B
Univers Condensed Bold Italic 5 3 4148 B
Garamond Antiqua 0 0 4197 B
Garamond Kursiv 1 0 4197 B
Garamond Halbfett 0 3 4197 B
Garamond Kursiv Halbfett 1 3 4197 B
CG Omega 0 0 4113 B
CG Omega Italic 1 0 4113 B
CG Omega Bold 0 3 4113 B
CG Omega Bold Italic 1 3 4113 B
Antique Olive 0 0 4168 B
Antique Olive Italic 1 0 4168 B
Antique Olive Bold 0 3 4168 B
Albertus Medium 0 1 4362 B
Albertus Extra Bold 0 4 4362 B
Clarendon Condensed Bold 4 3 4140 B
Marigold 0 0 4297 B
Coronet 1 0 4116 B
1 For the symbol sets supported by this font, see Table 2-7: “Non-Text PCL Emulation Symbol Sets” on page 2-17.

Forward and Backward Compatibility Mode Font Group Style Bold Typeface
Standard PCL Emulation Font Name
Times New Roman 0 0 16901 B
Times New Roman Italic 1 0 16901 B
Times New Roman Bold 0 3 16901 B
Times New Roman BoldItalic 1 3 16901 B
Arial 0 0 16602 B
Arial Italic 1 0 16602 B
Arial Bold 0 3 16602 B
Arial Bold Italic 1 3 16602 B
Symbol1 0 0 16686
Wingdings1 0 0 31402
Line Printer 161 0 0 0 A
POSTNET Bar Code1 0 0 0
OCR-B 1 0 0 23590 D
C39 Narrow1 0 0 32774
C39 Regular1 0 0 32772
C39 Wide1 0 0 32777
1 For the symbol sets supported by this font, see Table 2-7: “Non-Text PCL Emulation Symbol Sets” on page 2-17.

Thirty of the Type 1 fonts have different font selection parameters in the forward and backward compatibility modes and 9 of the fonts work only in the forward compatibility mode. With the appropriate printer driver installed and selected, your software application selects these fonts.
The following table shows the font selection commands for forward and backward compatibility modes and indicates the font group for each font. All Type 1 fonts are supported by both the Hewlett-Packard Company’s LaserJet 4050 and the Lexmark family of printers unless otherwise noted.
To determine which symbol sets are supported by a particular font, find the font group (A, B, or C) for the font in Table 2-5, and then see Table 2-6 on page 2-15 for the symbol sets that belong to that group.
Backward Compatibility Mode Font Group Style Bold Typeface Style Bold Typeface
Type 1 Font name
ITC Avant Garde Book 0 0 24607 0 0 61471 B
ITC Avant Garde Book Oblique 1 0 24607 1 0 61471 B
ITC Avant Garde Demi 1 0 2 24607 0 3 61471 B
ITC Avant Garde Demi Oblique 1 1 2 24607 1 3 61471 B
ITC Bookman Light 0 -3 24623 0 -3 61487 B
ITC Bookman Light Italic 1 -3 24623 1 -3 61487 B
ITC Bookman Demi 0 2 24623 0 2 61487 B
ITC Bookman Demi Italic 1 2 24623 1 2 61487 B
Century Schoolbook Roman 0 0 24703 0 0 61463 B
Century Schoolbook Italic 1 0 24703 1 0 61463 B
Century Schoolbook Bold 0 3 24703 0 3 61463 B
Century Schoolbook Bold Italic 1 3 24703 1 3 61463 B
Helvetica 0 0 24580 0 0 61444 B
Helvetica Italic 1 0 24580 1 0 61444 B
Helvetica Bold 0 3 24580 0 3 61444 B
Helvetica Bold Italic 1 3 24580 1 3 61444 B
Helvetica Narrow 4 0 24580 4 0 61444 B
1 Notice the values for forward compatibility and backward compatibility modes differ slightly for Bold. 2 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050. 3 For the symbol sets supported by this font, see Table 2-7: “Non-Text PCL Emulation Symbol Sets” on page 2-17.
Forward Compatibility Mode

Backward Compatibility Mode Font Group Style Bold Typeface Style Bold Typeface
Type 1 Font name
Helvetica Narrow Italic 5 0 24580 5 0 61444 B
Helvetica Narrow Bold 4 3 24580 4 3 61444 B
Helvetica Narrow Bold Italic 5 3 24580 5 3 61444 B
Helvetica Light 2 0 -3 24580 0 -3 61444 C
Helvetica Light Oblique 2 1 -3 24580 1 -3 61444 C
Helvetica Black 2 0 5 24580 0 5 61444 C
Helvetica Black Oblique 2 1 5 24580 1 5 61444 C
Palatino Roman 0 0 24591 0 0 61455 B
Palatino Italic 1 0 24591 1 0 61455 B
Palatino Bold 0 3 24591 0 3 61455 B
Palatino Bold Italic 1 3 24591 1 3 61455 B
ITC Zapf Chancery Medium Italic 1 0 45099 1 0 61483 B
ITC Zapf Dingbats 3 0 0 45101 0 0 61485
CourierPS 0 0 24579 B
CourierPS Oblique 1 0 24579 B
CourierPS Bold 0 3 24579 B
CourierPS Bold Oblique 1 3 24579 B
Times Roman 0 0 25093 B
Times Italic 1 0 25093 B
Times Bold 0 3 25093 B
Times Bold Italic 1 3 25093 B
SymbolPS 3 0 0 45358
1 Notice the values for forward compatibility and backward compatibility modes differ slightly for Bold. 2 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050. 3 For the symbol sets supported by this font, see Table 2-7: “Non-Text PCL Emulation Symbol Sets” on page 2-17.
Forward Compatibility Mode

Your Lexmark printer defaults to the forward compatibility mode to enable a Hewlett-Packard Company’s driver to select the forward compatibility fonts. The Lexmark PCL driver uses the backward compatibility mode and temporarily switches the printer to this mode. The PCL (PJL) commands to switch the default compatibility modes are:
Forward ESC%-12345X@PJL DEFAULT LPARM:PCL LFONTCOMPATIBILITY=PCL6
ESC %-12345X
Backward ESC%-12345X@PJL DEFAULT LPARM:PCL LFONTCOMPATIBILITY=PCL5
ESC %-12345X
Selecting Symbol Sets for the Lexmark X422
To determine which symbol sets a font or typeface from Table 2-4 or Table 2-5 supports, see the complete listing of PCL emulation fonts and symbol sets in the following tables.
Indicates the symbol set is supported
by the fonts in the font group. Symbol Set ID PJL Value
Symbol Set A B C D
Roman-8 8U ROMAN8
PC-8 Code Page 437 10U PC8
PC-8 Danish/Norwegian (437N) 11U PC8DN
PC-850 Multilingual 12U PC850
PC-852 Latin 2 17U PC852
PC-8 Turkish (437T) 9T PC8TK
PC-775 Baltic (PC-8 Latin 6) 26U
PC-1004 OS/2 9J
Legal 1U LEGAL
DeskTop 7J DESKTOP
MC Text 12J
PS Text 10J PSTEXT
Font Group

Indicates the symbol set is supported
by the fonts in the font group. Symbol Set ID PJL Value
Symbol Set A B C D
Math-8 8M MATH8
Pi Font 15U PIFONT
Microsoft Publishing 6J MSPUBL
Windows 3.0 Latin 1 9U WIN30
Windows Latin 1 19U WINL1
Windows Latin 2 9E WINL2
Windows Latin 5 5T WINL5
Windows Latin 6 (Baltic) 19L
ISO 8859-1 Latin 1 (ECMA-94) 0N ISOL1
ISO 8859-2 Latin 2 2N ISOL2
ISO 8859-9 Latin 5 5N ISOL5
ISO 8859-10 Latin 6 6N
ISO 8859-15 Latin 9 9N
PC-858 Multilingual Euro 13U
Roman-9 4U
Ventura International 13J VNINTL
Ventura US 14J VNUS
Ventura Math 6M VNMATH
PC-861 Iceland 21U
PC-863 Canadian French 23U
PC-865 Nordic 25U
PC-860 Portugal 20U
ABICOMP International 14P
ABICOMP Brazil/Portugal 13P
PC-8 PC Nova 27Q
PC-857 Latin 5 (Turkish) 16U
Turkish-8 8T
Font Group

Indicates the symbol set is supported
by the fonts in the font group. Symbol Set ID PJL Value
Symbol Set A B C D
PC-8 Polish Mazovia 24Q
Windows Cyrillic 9R
ISO 8859-5 Latin/Cyrillic 10N
PC-866 Cyrillic 3R
PC-855 Cyrillic 10R
Russian-GOST 12R
PC-8 Bulgarian 13R
Ukrainian 14R
Windows Greek 9G
ISO 8859-7 Latin/Greek 12N
PC-869 Greece 11G
PC-851 Greece 10G
PC-8 Latin/Greek 12G
Greek-8 8G
PC-8 Greek Alternate (437G) 14G
Symbol Set ID Fonts
PC-911 Katakana 3K Line Printer 16
Symbol 19M Symbol, SymbolPS
POSTNET Bar Code 15Y POSTNET Bar Code
Ventura ITC Zapf Dingbats 9L ITC Zapf Dingbats
PS ITC Zapf Dingbats 10L ITC Zapf Dingbats
PCL ITC Zapf Dingbats 14L ITC Zapf Dingbats
C39 Bar Code (Uppercase) 9Y Code 3 of 9
C39 Bar Code (plus Lowercase) 109Y Code 3 of 9
Font Group · Symbol Set · Wingdings 579L Wingding

Symbol Set ID Fonts
C39 Bar Code (plus Human Readable)
209Y Code 3 of 9
OCR-B 1O OCR-B
All fonts that support the Roman-8 (8U) symbol set also support the following 19 symbol sets.
Symbol Set ID Symbol Set
Symbol Set

Font and Symbol Set Support for the Lexmark C510(n)
Your printer has 91 resident fonts in PCL emulation, including 89 scalable fonts and two bitmapped fonts.
Several parameters are used to select a font from the data stream. These include symbol set, spacing, point or pitch, style, weight, and typeface number. For scalable fonts, you can vary the size of a font by specifying pitch or point size. For bitmapped fonts, you must choose the pitch or point size listed on the font sample pages. You can print the font sample pages from the printer operator panel, using a PJL command (see “LPRINTPCLFONTS” on page 3-83.) or through MarkVision Professional. Refer to your printer user documentation for more information.
A symbol set defines which characters are available for a font and the code point for each of these characters. Your printer supports 88 symbol sets. The tables beginning on page 2-15 show the symbol sets available for each font in PCL emulation. Not all fonts support all symbol sets.
You can select a font as the PCL emulation default from the printer operator panel or through MarkVision Professional. Refer to your printer user documentation for more information.
The fonts are divided into three major groups. The first 47 fonts (R0 through R46) shown on the font sample pages are the standard PCL emulation fonts. The next 39 fonts (R47 through R85) are called Type 1 fonts and were originally defined for PostScript emulation, but now also work in the PCL emulation. The last five fonts (R86 through R90) include three different Code 3 of 9 bar code fonts, OCR-A and OCR-B fonts.
The fonts are further divided into font groups A, B, and C indicating which symbol sets are supported by each font. For a list of the 47 standard PCL emulation fonts, as well as the OCR and Code 3 of 9 bar code fonts, see Table 2-4 on page 2-10. For a list of the 39 Type 1 fonts, see Table 2-5 on page 2-13. Both tables list the forward and backward compatibility font selection commands and the font group (A, B, or C) for each font. For more information on forward and backward compatibility, see page 2-10. For more information on selecting symbol sets, see page 2-15.
For compatibility purposes, you can disable Type 1 fonts with the Printer Job Language (PJL) LTYPE1FONTS command. The factory default for these fonts is Enabled. See LTYPE1FONTS on page 3-47 for more information.

You can also select fonts using PJL commands. The selection parameter is the number portion from the font identifier shown on the font sample pages, such as 0 or 76 from font identifiers R0 or R76. Use the PJL values shown in the tables beginning on page 2-15 to select a symbol set. If a symbol set does not have a PJL value, use the symbol set ID to select the symbol set. A font selection can be either temporary or set as the default.
Use the following PJL commands to select fonts: FONTSOURCE, FONTNUMBER, PITCH, PTSIZE, SYMSET, SET, DEFAULT. See Table 3-5: “Common Variables for PCL Emulation” on page 3-48 for more information about these commands.
Your PCL emulation has forward and backward compatibility modes. The forward compatibility mode is used to emulate the fonts in the Hewlett-Packard Company’s LaserJet 4050. The backward compatibility mode is used for compatibility with the Hewlett-Packard Company’s LaserJet 5 and the Lexmark family of printers.
Standard PCL Emulation Fonts, OCR and Code 3 of 9 bar code fonts
Table 2-4 on page 2-10 lists the font selection commands for forward and backward compatibility mode for each of the 47 standard PCL emulation fonts, the OCR and Code 3 of 9 bar code fonts. Since the font selection commands for the forward and backward compatibility modes are identical, they are listed together in the table. Most fonts are assigned a font group indicating which symbol sets that font supports.
To determine which symbol sets are supported by a particular font, find the font group (A, B, or C) for the font in Table 2-4, and then see Table 2-6 on page 2-15 for the symbol sets that belong to that group.
Forward and Backward Compatibility Mode Font Group Style Bold Typeface
Standard PCL Emulation Font Name
Courier 0 0 4099 A
Courier Italic 1 0 4099 A
Courier Bold 0 3 4099 A
1 For the symbol sets supported by this font, see Table 2-7: “Non-Text PCL Emulation Symbol Sets” on page 2-17.

Forward and Backward Compatibility Mode Font Group Style Bold Typeface
Standard PCL Emulation Font Name
Courier Bold Italic 1 3 4099 A
CG Times 0 0 4101 A
CG Times Italic 1 0 4101 A
CG Times Bold 0 3 4101 A
CG Times Bold Italic 1 3 4101 A
Univers Medium 0 0 4148 A
Univers Medium Italic 1 0 4148 A
Univers Bold 0 3 4148 A
Univers Bold Italic 1 3 4148 A
Letter Gothic 0 0 4102 B
Letter Gothic Italic 1 0 4102 B
Letter Gothic Bold 0 3 4102 B
Univers Condensed Medium 4 0 4148 B
Univers Condensed Medium Italic 5 0 4148 B
Univers Condensed Bold 4 3 4148 B
Univers Condensed Bold Italic 5 3 4148 B
Garamond Antiqua 0 0 4197 B
Garamond Kursiv 1 0 4197 B
Garamond Halbfett 0 3 4197 B
Garamond Kursiv Halbfett 1 3 4197 B
CG Omega 0 0 4113 B
CG Omega Italic 1 0 4113 B
CG Omega Bold 0 3 4113 B
CG Omega Bold Italic 1 3 4113 B
Antique Olive 0 0 4168 B
Antique Olive Italic 1 0 4168 B
Antique Olive Bold 0 3 4168 B
Albertus Medium 0 1 4362 B
Albertus Extra Bold 0 4 4362 B
Clarendon Condensed Bold 4 3 4140 B
Marigold 0 0 4297 B
1 For the symbol sets supported by this font, see Table 2-7: “Non-Text PCL Emulation Symbol Sets” on page 2-17.

Forward and Backward Compatibility Mode Font Group Style Bold Typeface
Standard PCL Emulation Font Name
Coronet 1 0 4116 B
Times New Roman 0 0 16901 B
Times New Roman Italic 1 0 16901 B
Times New Roman Bold 0 3 16901 B
Times New Roman BoldItalic 1 3 16901 B
Arial 0 0 16602 B
Arial Italic 1 0 16602 B
Arial Bold 0 3 16602 B
Arial Bold Italic 1 3 16602 B
Symbol1 0 0 16686
Wingdings1 0 0 31402
Line Printer 161 0 0 0 A
POSTNET Bar Code1 0 0 0
OCR-B 1 0 0 23590 D
C39 Narrow1 0 0 32774
C39 Regular1 0 0 32772
C39 Wide1 0 0 32777
1 For the symbol sets supported by this font, see Table 2-7: “Non-Text PCL Emulation Symbol Sets” on page 2-17.

Thirty of the Type 1 fonts have different font selection parameters in the forward and backward compatibility modes and 9 of the fonts work only in the forward compatibility mode. With the appropriate printer driver installed and selected, your software application selects these fonts.
The following table shows the font selection commands for forward and backward compatibility modes and indicates the font group for each font. All Type 1 fonts are supported by both the Hewlett-Packard Company’s LaserJet 4050 and the Lexmark family of printers unless otherwise noted.
To determine which symbol sets are supported by a particular font, find the font group (A, B, or C) for the font in Table 2-5, and then see Table 2-6 on page 2-15 for the symbol sets that belong to that group.
Backward Compatibility Mode Font Group Style Bold Typeface Style Bold Typeface
Type 1 Font name
ITC Avant Garde Book 0 0 24607 0 0 61471 B
ITC Avant Garde Book Oblique 1 0 24607 1 0 61471 B
ITC Avant Garde Demi 1 0 2 24607 0 3 61471 B
ITC Avant Garde Demi Oblique 1 1 2 24607 1 3 61471 B
ITC Bookman Light 0 -3 24623 0 -3 61487 B
ITC Bookman Light Italic 1 -3 24623 1 -3 61487 B
ITC Bookman Demi 0 2 24623 0 2 61487 B
ITC Bookman Demi Italic 1 2 24623 1 2 61487 B
Century Schoolbook Roman 0 0 24703 0 0 61463 B
Century Schoolbook Italic 1 0 24703 1 0 61463 B
Century Schoolbook Bold 0 3 24703 0 3 61463 B
Century Schoolbook Bold Italic 1 3 24703 1 3 61463 B
Helvetica 0 0 24580 0 0 61444 B
Helvetica Italic 1 0 24580 1 0 61444 B
Helvetica Bold 0 3 24580 0 3 61444 B
Helvetica Bold Italic 1 3 24580 1 3 61444 B
Helvetica Narrow 4 0 24580 4 0 61444 B
1 Notice the values for forward compatibility and backward compatibility modes differ slightly for Bold. 2 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050. 3 For the symbol sets supported by this font, see Table 2-7: “Non-Text PCL Emulation Symbol Sets” on page 2-17.
Forward Compatibility Mode

Backward Compatibility Mode Font Group Style Bold Typeface Style Bold Typeface
Type 1 Font name
Helvetica Narrow Italic 5 0 24580 5 0 61444 B
Helvetica Narrow Bold 4 3 24580 4 3 61444 B
Helvetica Narrow Bold Italic 5 3 24580 5 3 61444 B
Helvetica Light 2 0 -3 24580 0 -3 61444 C
Helvetica Light Oblique 2 1 -3 24580 1 -3 61444 C
Helvetica Black 2 0 5 24580 0 5 61444 C
Helvetica Black Oblique 2 1 5 24580 1 5 61444 C
Palatino Roman 0 0 24591 0 0 61455 B
Palatino Italic 1 0 24591 1 0 61455 B
Palatino Bold 0 3 24591 0 3 61455 B
Palatino Bold Italic 1 3 24591 1 3 61455 B
ITC Zapf Chancery Medium Italic 1 0 45099 1 0 61483 B
ITC Zapf Dingbats 3 0 0 45101 0 0 61485
CourierPS 0 0 24579 B
CourierPS Oblique 1 0 24579 B
CourierPS Bold 0 3 24579 B
CourierPS Bold Oblique 1 3 24579 B
Times Roman 0 0 25093 B
Times Italic 1 0 25093 B
Times Bold 0 3 25093 B
Times Bold Italic 1 3 25093 B
SymbolPS 3 0 0 45358
1 Notice the values for forward compatibility and backward compatibility modes differ slightly for Bold. 2 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050. 3 For the symbol sets supported by this font, see Table 2-7: “Non-Text PCL Emulation Symbol Sets” on page 2-17.
Forward Compatibility Mode

Your Lexmark printer defaults to the forward compatibility mode to enable a Hewlett-Packard Company’s driver to select the forward compatibility fonts. The Lexmark PCL driver uses the backward compatibility mode and temporarily switches the printer to this mode. The PCL (PJL) commands to switch the default compatibility modes are:
Forward ESC%-12345X@PJL DEFAULT LPARM:PCL LFONTCOMPATIBILITY=PCL6
ESC %-12345X
Backward ESC%-12345X@PJL DEFAULT LPARM:PCL LFONTCOMPATIBILITY=PCL5
ESC %-12345X
Selecting Symbol Sets for the Lexmark C510(n)
To determine which symbol sets a font or typeface from Table 2-4 or Table 2-5 supports, see the complete listing of PCL emulation fonts and symbol sets in the following tables.
Indicates the symbol set is supported
by the fonts in the font group. Symbol Set ID PJL Value
Symbol Set A B C D
Roman-8 8U ROMAN8
PC-8 Code Page 437 10U PC8
PC-8 Danish/Norwegian (437N) 11U PC8DN
PC-850 Multilingual 12U PC850
PC-852 Latin 2 17U PC852
PC-8 Turkish (437T) 9T PC8TK
PC-775 Baltic (PC-8 Latin 6) 26U
PC-1004 OS/2 9J
Legal 1U LEGAL
DeskTop 7J DESKTOP
MC Text 12J
PS Text 10J PSTEXT
Font Group

Indicates the symbol set is supported
by the fonts in the font group. Symbol Set ID PJL Value
Symbol Set A B C D
Math-8 8M MATH8
Pi Font 15U PIFONT
Microsoft Publishing 6J MSPUBL
Windows 3.0 Latin 1 9U WIN30
Windows Latin 1 19U WINL1
Windows Latin 2 9E WINL2
Windows Latin 5 5T WINL5
Windows Latin 6 (Baltic) 19L
ISO 8859-1 Latin 1 (ECMA-94) 0N ISOL1
ISO 8859-2 Latin 2 2N ISOL2
ISO 8859-9 Latin 5 5N ISOL5
ISO 8859-10 Latin 6 6N
ISO 8859-15 Latin 9 9N
PC-858 Multilingual Euro 13U
Roman-9 4U
Ventura International 13J VNINTL
Ventura US 14J VNUS
Ventura Math 6M VNMATH
PC-861 Iceland 21U
PC-863 Canadian French 23U
PC-865 Nordic 25U
PC-860 Portugal 20U
ABICOMP International 14P
ABICOMP Brazil/Portugal 13P
PC-8 PC Nova 27Q
PC-857 Latin 5 (Turkish) 16U
Turkish-8 8T
Font Group

Indicates the symbol set is supported
by the fonts in the font group. Symbol Set ID PJL Value
Symbol Set A B C D
PC-8 Polish Mazovia 24Q
Windows Cyrillic 9R
ISO 8859-5 Latin/Cyrillic 10N
PC-866 Cyrillic 3R
PC-855 Cyrillic 10R
Russian-GOST 12R
PC-8 Bulgarian 13R
Ukrainian 14R
Windows Greek 9G
ISO 8859-7 Latin/Greek 12N
PC-869 Greece 11G
PC-851 Greece 10G
PC-8 Latin/Greek 12G
Greek-8 8G
PC-8 Greek Alternate (437G) 14G
Symbol Set ID Fonts
PC-911 Katakana 3K Line Printer 16
Symbol 19M Symbol, SymbolPS
POSTNET Bar Code 15Y POSTNET Bar Code
Ventura ITC Zapf Dingbats 9L ITC Zapf Dingbats
PS ITC Zapf Dingbats 10L ITC Zapf Dingbats
PCL ITC Zapf Dingbats 14L ITC Zapf Dingbats
C39 Bar Code (Uppercase) 9Y Code 3 of 9
C39 Bar Code (plus Lowercase) 109Y Code 3 of 9
Font Group · Symbol Set · Wingdings 579L Wingding

Symbol Set ID Fonts
C39 Bar Code (plus Human Readable)
209Y Code 3 of 9
OCR-B 1O OCR-B
All fonts that support the Roman-8 (8U) symbol set also support the following 19 symbol sets.
Symbol Set ID Symbol Set
Symbol Set

Font and Symbol Set Support for the Lexmark E230, E232
Your printer supports 19 fonts in PCL emulation, including 17 scalable fonts and two bitmapped fonts.
Several parameters are used to select a font from the data stream. These include symbol set, spacing, point or pitch, style, weight, and typeface number. Print the font sample pages to view the specific parameters for each font. For scalable fonts, you can vary the size of a font by specifying pitch or point size. For bitmapped fonts, you must choose the pitch or point size listed on the font sample pages. You can print the font sample pages using a PJL command (see “LPRINTPCLFONTS” on page 3-83).
A symbol set defines which characters are available for a font and the code point for each of these characters. Your printer has 83 resident symbol sets. The tables beginning on page 2-32 show the symbol sets available for each font in PCL emulation. Not all fonts support all symbol sets.
You can also select fonts using PJL commands. The selection parameter is the number portion from the font identifier shown on the font sample pages, such as 0 or 18 from font identifiers R0 or R18. Use the PJL values shown in the tables beginning on page 2-32 to select a symbol set. If a symbol set does not have a PJL value, use the symbol set ID to select the symbol set. A font selection can be either temporary or set as the default.
Use the following PJL commands to select fonts: FONTSOURCE, FONTNUMBER, PITCH, PTSIZE, SYMSET, SET, DEFAULT. See “Table 3-5: Common Variables for PCL Emulation” on page 3-48 for more information about these commands.

Forward and Backward Compatibility Modes for the Lexmark E230, E232
Your PCL emulation has forward and backward compatibility modes. The forward compatibility mode is used to emulate the fonts in the Hewlett-Packard Company’s LaserJet 4050. The backward compatibility mode is used for compatibility with the Hewlett-Packard Company’s LaserJet 5 and the Lexmark family of printers.
The following table lists the font selection commands for forward and backward compatibility mode for each of the 14 standard PCL emulation fonts. Since the font selection commands for the forward and backward compatibility modes are identical, they are listed together in the table.
Forward and Backward Compatibility Mode
Standard PCL Emulation Font Name
Spacing Style Weight Typeface
Courier 0 0 0 4099
Courier Italic 0 1 0 4099
Courier Bold 0 0 3 4099
Courier Bold Italic 0 1 3 4099
Times New Roman 1 0 0 16901
Times New Roman Italic 1 1 0 16901
Times New Roman Bold 1 0 3 16901
Times New Roman BoldItalic 1 1 3 16901
Arial 1 0 0 16602
Arial Italic 1 1 0 16602
Arial Bold 1 0 3 16602
Arial Bold Italic 1 1 3 16602
Line Printer 16 0
POSTNET Barcode 1 1 0 0 0
1 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050.

The following table lists the font selection commands for forward and backward compatibility mode for each of the five specialty PCL fonts. Since the font selection commands for the forward and backward compatibility modes are identical, they are listed together in the table.
Forward and Backward Compatibility Mode
Standard PCL Emulation Font Name
Spacing Style Weight Typeface
C39 Narrow 1 1 0 0 32774
C39 Regular 1 1 0 0 32772
C39 Wide 1 1 0 0 32777
OCR-B 1 0 0 0 23590
1 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050.

Selecting Symbol Sets for Lexmark E230, E232
To determine if a font or typeface supports a symbol set, see the complete listing of PCL emulation fonts and symbol sets in the following tables: “Table 2-16: PCL Emulation Symbol Sets - Latin 1” on page 2-32, “Table 2-17: PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek” on page 2-34, and “Table 2-18: PCL Emulation Symbol Sets - Specials” on page 2-35.
ISO 8859-1 Latin 1 (ECMA-94)
PC-8, Code Page 437
Windows 3.0 Latin 1
Windows 98 Latin 1
ISO 8859-15 Latin 9
Typeface / Symbol Set
ROMAN8
PSTEXT
VNINTL
LEGAL
WIN30
WINL1
ISOL1
ISOL9
PC8DN
PC850
PC858
VNUS
PC8
19U
10U
11U
12U
13U
20U 21U 23U 25U 9J 13P 14P 8U
10J
12J
13J
14J
1U
9U
0N
9N
4U
0E
7J
Courier
Courier Italic
Courier Bold
Courier Bold Italic
Times New Roman
Times New Roman Italic
Times New Roman Bold
Times New Roman Bold Italic
Arial
Arial Italic
Arial Bold
Arial Bold Italic
Line Printer 16
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.


POSTNET Barcode ✘
C39 Narrow ✘
C39 Regular ✘
C39 Wide ✘
OCR-A ✘
OCR-B ✘ ✘ ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.

Latin 2 Latin 5 Latin 6 Cyrillic Greek
Windows 98 Latin 6 (Baltic)
PC-775 Baltic (PC-8 Latin 6)
PC-8 Greek Alternate (437G)
PC-857 Latin 5 (Turkish)
PC-853 Latin 3 (Turkish)
Windows 98 Latin 2
Windows 98 Latin 5
ISO 8859-10 Latin 6
ISO 8859-2 Latin 2
ISO 8859-9 Latin 5
Typeface / Symbol Set
PC852
WINL5
PC8TK
ISOL2
ISOL5
17U
24Q
27Q
16U
18U
26U
10N
10R
12R
13R
14R
12N
11G
10G
12G
14G
9E
2N
5T
5N
9T
8T
6N
9R
3R
9G
8G
Courier
Courier Italic
Courier Bold
Courier Bold Italic
Times New Roman ✘ ✘
Times New Roman Italic ✘ ✘
Times New Roman Bold ✘ ✘
Times New Roman BoldItalic
✘ ✘
Arial ✘ ✘
Arial Italic ✘ ✘
Arial Bold ✘ ✘
Arial Bold Italic ✘ ✘
Line Printer 16
POSTNET Barcode ✘
C39 Narrow ✘
C39 Regular ✘
C39 Wide ✘
OCR-A ✘
OCR-B ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.

Ventura ITC Zapf Dingbats
PCL ITC Zapf Dingbats
PS ITC Zapf Dingbats
OCR-B
Typeface / Symbol Set
PSMATH
MSPUBL
MATH8
PIFONT
109Y
209Y
15U
15Y
19M
6M
5M
8M
6J
3K
0O
1O
9Y
Courier ✘
Courier Italic ✘
Courier Bold ✘
Courier Bold Italic ✘
Times New Roman ✘
Times New Roman Italic ✘
Times New Roman Bold ✘
Times New Roman BoldItalic ✘
Arial ✘
Arial Italic ✘
Arial Bold ✘
Arial Bold Italic ✘
Line Printer 16 ✘
POSTNET Barcode ✘
C39 Narrow ✘
C39 Regular ✘
C39 Wide ✘
OCR-A ✘
OCR-B ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.

All fonts that support the Roman-8 (8U) symbol set also support the following 19 symbol sets.
Symbol Set ID Symbol Set / Typeface

Font and Symbol Set Support for the Lexmark E234(n), E330, E332n
Your printer has 91 resident fonts in PCL emulation, including 89 scalable fonts and two bitmapped fonts.
Several parameters are used to select a font from the data stream. These include symbol set, spacing, point or pitch, style, weight, and typeface number. For scalable fonts, you can vary the size of a font by specifying pitch or point size. For bitmapped fonts, you must choose the pitch or point size listed on the font sample pages. You can print the font sample pages using a PJL command (see “LPRINTPCLFONTS” on page 3-83), or through MarkVision Professional (network models only). Refer to your printer user documentation for more information.
A symbol set defines which characters are available for a font and the code point for each of these characters. Your printer supports 88 resident symbol sets. The tables beginning on page 2-43 show the symbol sets available for each font in PCL emulation. Not all fonts support all symbol sets.
You can select a font as the PCL emulation default through MarkVision Professional (network models only). Refer to your printer user documentation for more information.
The fonts are divided into three major groups. The first 47 fonts (R0 to R46) shown on the font sample pages are the standard PCL emulation fonts. The next 39 fonts (R47 to R85) are called Type 1 fonts and were originally defined for PostScript emulation, but now also work in the PCL emulation. The final five fonts (R86 to R90) are additional specialty PCL fonts. For a list of the 47 standard PCL emulation fonts, see Table 2-20 on page 2-38. For a list of the 39 Type 1 fonts, see Table 2-21 on page 2-40. For a list of the five additional specialty PCL fonts, see Table 2-22 on page 2-42. These tables list both the forward and backward compatibility font selection commands. For more information on forward and backward compatibility, see page 2-38. For more information on selecting symbol sets, see page 2-43.
For compatibility purposes, you can disable Type 1 fonts with the Printer Job Language (PJL) LTYPE1FONTS command. The factory default for these fonts is Enabled. See LTYPE1FONTS on page 3-47 for more information.
You can also select fonts using PJL commands. The selection parameter is the number portion from the font identifier shown on the font sample pages, such as 0 or 76 from font identifiers R0 or R76. Use the PJL values shown in the tables beginning

on page 2-43 to select a symbol set. If a symbol set does not have a PJL value, use the symbol set ID to select the symbol set. A font selection can be either temporary or set as the default.
Use the following PJL commands to select fonts: FONTSOURCE, FONTNUMBER, PITCH, PTSIZE, SYMSET, SET, DEFAULT. See “Table 3-5: Common Variables for PCL Emulation” on page 3-48 for more information about these commands.
Your PCL emulation has forward and backward compatibility modes. The forward compatibility mode is used to emulate the fonts in the Hewlett-Packard Company’s LaserJet 4050. The backward compatibility mode is used for compatibility with the Hewlett-Packard Company’s LaserJet 5 and the Lexmark family of printers.
The following table lists the font selection commands for forward and backward compatibility mode for each of the 47standard PCL emulation fonts. Since the font selection commands for the forward and backward compatibility modes are identical, they are listed together in the table.
Forward and Backward Compatibility Mode
Standard PCL Emulation Font Name
Spacing Style Weight Typeface
Courier 0 0 0 4099
Courier Italic 0 1 0 4099
Courier Bold 0 0 3 4099
Courier Bold Italic 0 1 3 4099
CG Times 1 0 0 4101
CG Times Italic 1 1 0 4101
CG Times Bold 1 0 3 4101
CG Times Bold Italic 1 1 3 4101
Univers Medium 1 0 0 4148
Univers Medium Italic 1 1 0 4148
Univers Bold 1 0 3 4148
1 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050.

Forward and Backward Compatibility Mode
Standard PCL Emulation Font Name
Spacing Style Weight Typeface
Univers Bold Italic 1 1 3 4148
Times New Roman 1 0 0 16901
Times New Roman Italic 1 1 0 16901
Times New Roman Bold 1 0 3 16901
Times New Roman BoldItalic 1 1 3 16901
Arial 1 0 0 16602
Arial Italic 1 1 0 16602
Arial Bold 1 0 3 16602
Arial Bold Italic 1 1 3 16602
Letter Gothic 0 0 0 4102
Letter Gothic Italic 0 1 0 4102
Letter Gothic Bold 0 0 3 4102
Univers Condensed Medium 1 4 0 4148
Univers Condensed Medium Italic 1 5 0 4148
Univers Condensed Bold 1 4 3 4148
Univers Condensed Bold Italic 1 5 3 4148
Garamond Antiqua 1 0 0 4197
Garamond Kursiv 1 1 0 4197
Garamond Halbfett 1 0 3 4197
Garamond Kursiv Halbfett 1 1 3 4197
CG Omega 1 0 0 4113
CG Omega Italic 1 1 0 4113
CG Omega Bold 1 0 3 4113
CG Omega Bold Italic 1 1 3 4113
Antique Olive 1 0 0 4168
Antique Olive Italic 1 1 0 4168
Antique Olive Bold 1 0 3 4168
Albertus Medium 1 0 1 4362
Albertus Extra Bold 1 0 4 4362
Clarendon Condensed Bold 1 4 3 4140
Marigold 1 0 0 4297
Coronet 1 1 0 4116
Line Printer 16 0
1 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050.

Forward and Backward Compatibility Mode
Standard PCL Emulation Font Name
Spacing Style Weight Typeface
POSTNET Barcode 1 1 0 0 0
Wingdings 1 0 0 31402
Symbol 1 0 0 16686
1 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050.
Thirty of the Type 1 fonts have different font selection parameters in the forward and backward compatibility modes and 9 of the fonts work only in the forward compatibility mode. With the appropriate printer driver installed and selected, your software program selects these fonts.
The following table shows the font selection commands for forward and backward compatibility modes and indicates the font group for each font. All Type 1 fonts are supported by both the Hewlett-Packard Company’s LaserJet 4050 and the Lexmark family of printers unless otherwise noted.
Forward Compatibility Mode Backward Compatibility Mode
Type 1 Font name
Spacing Style Weight Typeface Spacing Style Weight Typeface
Helvetica 1 0 0 24580 1 0 0 61444
Helvetica Italic 1 1 0 24580 1 1 0 61444
Helvetica Bold 1 0 3 24580 1 0 3 61444
Helvetica Bold Italic 1 1 3 24580 1 1 3 61444
Helvetica Narrow 1 4 0 24580 1 4 0 61444
Helvetica Narrow Italic 1 5 0 24580 1 5 0 61444
Helvetica Narrow Bold 1 4 3 24580 1 4 3 61444
Helvetica Narrow Bold Italic 1 5 3 24580 1 5 3 61444
Palatino Roman 1 0 0 24591 1 0 0 61455
Palatino Italic 1 1 0 24591 1 1 0 61455
Palatino Bold 1 0 3 24591 1 0 3 61455
Palatino Bold Italic 1 1 3 24591 1 1 3 61455
1 Notice the values for forward and backward compatibility modes differ slightly for Bold. 2 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050. 3 This font is not implemented in the Lexmark family of printers.

Forward Compatibility Mode Backward Compatibility Mode
Type 1 Font name
Spacing Style Weight Typeface Spacing Style Weight Typeface
ITC Bookman Light 1 0 -3 24623 1 0 -3 61487
ITC Bookman Light Italic 1 1 -3 24623 1 1 -3 61487
ITC Bookman Demi 1 0 2 24623 1 0 2 61487
ITC Bookman Demi Italic 1 1 2 24623 1 1 2 61487
ITC Avant Garde Book 1 0 0 24607 1 0 0 61471
ITC Avant Garde Book Oblique 1 1 0 24607 1 1 0 61471
ITC Avant Garde Demi 1 1 0 2 24607 1 0 3 61471
ITC Avant Garde Demi Oblique 1 1 1 2 24607 1 1 3 61471
Century Schoolbook Roman 1 0 0 24703 1 0 0 61463
Century Schoolbook Italic 1 1 0 24703 1 1 0 61463
Century Schoolbook Bold 1 0 3 24703 1 0 3 61463
Century Schoolbook Bold Italic 1 1 3 24703 1 1 3 61463
ITC Zapf Chancery Medium Italic 1 1 0 45099 1 1 0 61483
CourierPS 3 0 0 0 24579
CourierPS Oblique 3 0 1 0 24579
CourierPS Bold 3 0 0 3 24579
CourierPS Bold Oblique 3 0 1 3 24579
Times Roman 3 1 0 0 25093
Times Italic 3 1 1 0 25093
Times Bold 3 1 0 3 25093
Times Bold Italic 3 1 1 3 25093
Helvetica Light 2 1 0 -3 24580 1 0 -3 61444
Helvetica Light Oblique 2 1 1 -3 24580 1 1 -3 61444
Helvetica Black 2 1 0 5 24580 1 0 5 61444
Helvetica Black Oblique 2 1 1 5 24580 1 1 5 61444
SymbolPS 3 1 0 0 45358
ITC Zapf Dingbats 1 0 0 45101 1 0 0 61485
1 Notice the values for forward and backward compatibility modes differ slightly for Bold. 2 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050. 3 This font is not implemented in the Lexmark family of printers.

Your Lexmark printer defaults to the forward compatibility mode to enable a Hewlett-Packard Company’s driver to select the forward compatibility fonts. The Lexmark PCL driver uses the backward compatibility mode and temporarily switches the printer to this mode. The PCL (PJL) commands to switch the default compatibility modes are:
Forward ESC%-12345X@PJL DEFAULT LPARM:PCL LFONTCOMPATIBILITY=PCL6
ESC %-12345X
Backward ESC%-12345X@PJL DEFAULT LPARM:PCL LFONTCOMPATIBILITY=PCL5
ESC %-12345X
Specialty PCL Fonts
The following table lists the font selection commands for forward and backward compatibility mode for each of the five specialty PCL fonts. Since the font selection commands for the forward and backward compatibility modes are identical, they are listed together in the table.
Forward and Backward Compatibility Mode
Standard PCL Emulation Font Name
Spacing Style Weight Typeface
C39 Narrow 1 1 0 0 32774
C39 Regular 1 1 0 0 32772
C39 Wide 1 1 0 0 32777
OCR-B 1 0 0 0 23590
1 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050.

Selecting Symbol Sets for the Lexmark E234(n), E330, and E332n
To determine if a font or typeface supports a symbol set, see the complete listing of PCL emulation fonts and symbol sets in the following tables: “Table 2-23: PCL Emulation Symbol Sets - Latin 1” on page 2-43, “Table 2-24: PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek” on page 2-48, and “Table 2-25: PCL Emulation Symbol Sets - Specials” on page 2-53.
ISO 8859-1 Latin 1 (ECMA-94)
PC-8, Code Page 437
Windows 3.0 Latin 1
Windows 98 Latin 1
ISO 8859-15 Latin 9
Typeface / Symbol Set
ROMAN8
PSTEXT
VNINTL
LEGAL
WIN30
WINL1
ISOL1
ISOL9
PC8DN
PC850
PC858
VNUS
PC8
19U
10U
11U
12U
13U
20U 21U 23U 25U 9J 13P 14P 8U
10J
12J
13J
14J
1U
9U
0N
9N
4U
0E
7J
Courier
Courier Italic
Courier Bold
Courier Bold Italic
CG Times
CG Times Italic
CG Times Bold
CG Times Bold Italic
Univers Medium
Univers Medium Italic
Univers Bold
Univers Bold Italic
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.
this font is not supported or this font does not support this symbol set.

ISO 8859-1 Latin 1 (ECMA-94)
PC-8, Code Page 437
Windows 3.0 Latin 1
Windows 98 Latin 1
ISO 8859-15 Latin 9
Typeface / Symbol Set
ROMAN8
PSTEXT
LEGAL
WIN30
WINL1
PC8DN
PC850
PC858
VNINTL
ISOL1
ISOL9
VNUS
PC8
19U
10U
11U
12U
13U
20U 21U 23U 25U 9J 13P 14P 8U
1U
9U
0N
9N
4U
0E
10J
12J
13J
14J
7J
Times New Roman
Times New Roman Italic
Times New Roman Bold
Times New Roman Bold Italic
Arial
Arial Italic
Arial Bold
Arial Bold Italic
Letter Gothic
Letter Gothic Italic
Letter Gothic Bold
Univers Condensed Medium
Univers Condensed Medium Italic
Univers Condensed Bold
Univers Condensed Bold Italic
Garamond Antiqua
Garamond Kursiv
Garamond Halbfett
Garamond Kursiv Halbfett
CG Omega
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.
this font is not supported or this font does not support this symbol set.

ISO 8859-1 Latin 1 (ECMA-94)
PC-8, Code Page 437
Windows 3.0 Latin 1
Windows 98 Latin 1
ISO 8859-15 Latin 9
Typeface / Symbol Set
ROMAN8
PSTEXT
LEGAL
WIN30
WINL1
PC8DN
PC850
PC858
VNINTL
ISOL1
ISOL9
VNUS
PC8
19U
10U
11U
12U
13U
20U 21U 23U 25U 9J 13P 14P 8U
1U
9U
0N
9N
4U
0E
10J
12J
13J
14J
7J
CG Omega Italic
CG Omega Bold
CG Omega Bold Italic
Antique Olive
Antique Olive Italic
Antique Olive Bold
Albertus Medium
Albertus Extra Bold
Clarendon Condensed Bold
Marigold
Coronet
Helvetica
Helvetica Italic
Helvetica Bold
Helvetica Bold Italic
Helvetica Narrow
Helvetica Narrow Italic
Helvetica Narrow Bold
Helvetica Narrow Bold Italic
Palatino Roman
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.
this font is not supported or this font does not support this symbol set.

ISO 8859-1 Latin 1 (ECMA-94)
PC-8, Code Page 437
Windows 3.0 Latin 1
Windows 98 Latin 1
ISO 8859-15 Latin 9
Typeface / Symbol Set
ROMAN8
PSTEXT
LEGAL
WIN30
WINL1
PC8DN
PC850
PC858
VNINTL
ISOL1
ISOL9
VNUS
PC8
19U
10U
11U
12U
13U
20U 21U 23U 25U 9J 13P 14P 8U
1U
9U
0N
9N
4U
0E
10J
12J
13J
14J
7J
Palatino Italic
Palatino Bold
Palatino Bold Italic
ITC Bookman Light
ITC Bookman Light Italic
ITC Bookman Demi
ITC Bookman Demi Italic
ITC Avant Garde Book
ITC Avant Garde Book Oblique
ITC Avant Garde Demi
ITC Avant Garde Demi Oblique
Century Schoolbook Roman
Century Schoolbook Italic
Century Schoolbook Bold
Century Schoolbook Bold Italic
ITC Zapf Chancery Medium Italic
CourierPS
CourierPS Oblique
CourierPS Bold
CourierPS Bold Oblique
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.
this font is not supported or this font does not support this symbol set.

ISO 8859-1 Latin 1 (ECMA-94)
PC-8, Code Page 437
Windows 3.0 Latin 1
Windows 98 Latin 1
ISO 8859-15 Latin 9
Typeface / Symbol Set
ROMAN8
PSTEXT
LEGAL
WIN30
WINL1
PC8DN
PC850
PC858
VNINTL
ISOL1
ISOL9
VNUS
PC8
19U
10U
11U
12U
13U
20U 21U 23U 25U 9J 13P 14P 8U
1U
9U
0N
9N
4U
0E
10J
12J
13J
14J
7J
Times Roman
Times Italic
Times Bold
Times Bold Italic
Helvetica Light ✘
Helvetica Light Oblique ✘
Helvetica Black ✘
Helvetica Black Oblique ✘
Line Printer 16
POSTNET Barcode ✘
C39 Narrow ✘
C39 Regular ✘
C39 Wide ✘
OCR-A ✘
OCR-B ✘ ✘ ✘
Wingdings ✘
Symbol ✘
SymbolPS ✘
ITC Zapf Dingbats ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.
this font is not supported or this font does not support this symbol set.

Latin 2 Latin 5 Latin 6 Cyrillic Greek
Windows 98 Latin 6 (Baltic)
PC-775 Baltic (PC-8 Latin 6)
PC-8 Greek Alternate (437G)
PC-857 Latin 5 (Turkish)
PC-853 Latin 3 (Turkish)
Windows 98 Latin 2
Windows 98 Latin 5
ISO 8859-10 Latin 6
ISO 8859-2 Latin 2
ISO 8859-9 Latin 5
Typeface / Symbol Set
PC852
WINL5
PC8TK
ISOL2
ISOL5
17U
24Q
27Q
16U
18U
26U
10N
10R
12R
13R
14R
12N
11G
10G
12G
14G
9E
2N
5T
5N
9T
8T
6N
9R
3R
9G
8G
Courier
Courier Italic
Courier Bold
Courier Bold Italic
CG Times
CG Times Italic
CG Times Bold
CG Times Bold Italic
Univers Medium
Univers Medium Italic
Univers Bold
Univers Bold Italic
Times New Roman ✘
Times New Roman Italic ✘
Times New Roman Bold ✘
Times New Roman BoldItalic
✘
Arial ✘
Arial Italic ✘
Arial Bold ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol
is not supported or this font does not support this symbol set.
Set.

Latin 2 Latin 5 Latin 6 Cyrillic Greek
PC-8 Greek Alternate (437G)
Windows 98 Latin 6 (Baltic)
PC-775 Baltic (PC-8 Latin 6)
PC-857 Latin 5 (Turkish)
PC-853 Latin 3 (Turkish)
Windows 98 Latin 2
Windows 98 Latin 5
ISO 8859-10 Latin 6
ISO 8859-2 Latin 2
ISO 8859-9 Latin 5
Typeface / Symbol Set
PC852
WINL5
PC8TK
ISOL2
ISOL5
17U
24Q
27Q
16U
18U
26U
10N
10R
12R
13R
14R
12N
11G
10G
12G
14G
9E
2N
5T
5N
9T
8T
6N
9R
3R
9G
8G
Arial Bold Italic ✘
Letter Gothic ✘
Letter Gothic Italic ✘
Letter Gothic Bold ✘
✘
Univers Condensed Medium Italic
✘
Univers Condensed Bold ✘
Univers Condensed Bold Italic
✘
Garamond Antiqua ✘
Garamond Kursiv ✘
Garamond Halbfett ✘
✘
CG Omega ✘
CG Omega Italic ✘
CG Omega Bold ✘
CG Omega Bold Italic ✘
Antique Olive ✘
Antique Olive Italic ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol
is not supported or this font does not support this symbol set.
Set.

Latin 2 Latin 5 Latin 6 Cyrillic Greek
PC-8 Greek Alternate (437G)
Windows 98 Latin 6 (Baltic)
PC-775 Baltic (PC-8 Latin 6)
PC-857 Latin 5 (Turkish)
PC-853 Latin 3 (Turkish)
Windows 98 Latin 2
Windows 98 Latin 5
ISO 8859-10 Latin 6
ISO 8859-2 Latin 2
ISO 8859-9 Latin 5
Typeface / Symbol Set
PC852
WINL5
PC8TK
ISOL2
ISOL5
17U
24Q
27Q
16U
18U
26U
10N
10R
12R
13R
14R
12N
11G
10G
12G
14G
9E
2N
5T
5N
9T
8T
6N
9R
3R
9G
8G
Antique Olive Bold ✘
Albertus Medium ✘
Albertus Extra Bold ✘
✘
Marigold ✘
Coronet ✘
Helvetica ✘
Helvetica Italic ✘
Helvetica Bold ✘
Helvetica Bold Italic ✘
Helvetica Narrow ✘
Helvetica Narrow Italic ✘
Helvetica Narrow Bold ✘
Helvetica Narrow Bold Italic
✘
Palatino Roman ✘
Palatino Italic ✘
Palatino Bold ✘
Palatino Bold Italic ✘
ITC Bookman Light ✘
ITC Bookman Light Italic ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol
is not supported or this font does not support this symbol set.
Set.

Latin 2 Latin 5 Latin 6 Cyrillic Greek
PC-8 Greek Alternate (437G)
Windows 98 Latin 6 (Baltic)
PC-775 Baltic (PC-8 Latin 6)
PC-857 Latin 5 (Turkish)
PC-853 Latin 3 (Turkish)
Windows 98 Latin 2
Windows 98 Latin 5
ISO 8859-10 Latin 6
ISO 8859-2 Latin 2
ISO 8859-9 Latin 5
Typeface / Symbol Set
PC852
WINL5
PC8TK
ISOL2
ISOL5
17U
24Q
27Q
16U
18U
26U
10N
10R
12R
13R
14R
12N
11G
10G
12G
14G
9E
2N
5T
5N
9T
8T
6N
9R
3R
9G
8G
ITC Bookman Demi ✘
ITC Bookman Demi Italic ✘
ITC Avant Garde Book ✘
ITC Avant Garde Book Oblique
✘
ITC Avant Garde Demi ✘
ITC Avant Garde Demi Oblique
✘
✘
✘
✘
Century Schoolbook Bold Italic
✘
ITC Zapf Chancery Medium Italic
✘
CourierPS ✘
CourierPS Oblique ✘
CourierPS Bold ✘
CourierPS Bold Oblique ✘
Times Roman ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol
is not supported or this font does not support this symbol set.
Set.

Latin 2 Latin 5 Latin 6 Cyrillic Greek
PC-8 Greek Alternate (437G)
Windows 98 Latin 6 (Baltic)
PC-775 Baltic (PC-8 Latin 6)
PC-857 Latin 5 (Turkish)
PC-853 Latin 3 (Turkish)
Windows 98 Latin 2
Windows 98 Latin 5
ISO 8859-10 Latin 6
ISO 8859-2 Latin 2
ISO 8859-9 Latin 5
Typeface / Symbol Set
PC852
WINL5
PC8TK
ISOL2
ISOL5
17U
24Q
27Q
16U
18U
26U
10N
10R
12R
13R
14R
12N
11G
10G
12G
14G
9E
2N
5T
5N
9T
8T
6N
9R
3R
9G
8G
Times Italic ✘
Times Bold ✘
Times Bold Italic ✘
Helvetica Light ✘
Helvetica Light Oblique ✘
Helvetica Black ✘
Helvetica Black Oblique ✘
Line Printer 16
POSTNET Barcode ✘
C39 Narrow ✘
C39 Regular ✘
C39 Wide ✘
OCR-A ✘
OCR-B ✘
Wingdings ✘
Symbol ✘
SymbolPS ✘
ITC Zapf Dingbats ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol
is not supported or this font does not support this symbol set.
Set.

Ventura ITC Zapf Dingbats
PCL ITC Zapf Dingbats
PS ITC Zapf Dingbats
OCR-B
Typeface / Symbol Set
PSMATH
MSPUBL
MATH8
PIFONT
109Y
209Y
15U
15Y
19M
6M
5M
8M
6J
3K
0O
1O
9Y
Courier ✘
Courier Italic ✘
Courier Bold ✘
Courier Bold Italic ✘
CG Times ✘
CG Times Italic ✘
CG Times Bold ✘
CG Times Bold Italic ✘
Univers Medium ✘
Univers Medium Italic ✘
Univers Bold ✘
Univers Bold Italic ✘
Times New Roman ✘
Times New Roman Italic ✘
Times New Roman Bold ✘
Times New Roman BoldItalic ✘
Arial ✘
Arial Italic ✘
Arial Bold ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.
this font is not supported or this font does not support this symbol set.

Ventura ITC Zapf Dingbats
PCL ITC Zapf Dingbats
PS ITC Zapf Dingbats
OCR-B
Typeface / Symbol Set
PSMATH
PIFONT
MSPUBL
MATH8
109Y
209Y
19M
15U
15Y
6M
5M
8M
6J
3K
0O
1O
9Y
Arial Bold Italic ✘
Letter Gothic ✘
Letter Gothic Italic ✘
Letter Gothic Bold ✘
Univers Condensed Medium ✘
Univers Condensed Medium Italic ✘
Univers Condensed Bold ✘
Univers Condensed Bold Italic ✘
Garamond Antiqua ✘
Garamond Kursiv ✘
Garamond Halbfett ✘
Garamond Kursiv Halbfett ✘
CG Omega ✘
CG Omega Italic ✘
CG Omega Bold ✘
CG Omega Bold Italic ✘
Antique Olive ✘
Antique Olive Italic ✘
Antique Olive Bold ✘
Albertus Medium ✘
Albertus Extra Bold ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.
this font is not supported or this font does not support this symbol set.

Ventura ITC Zapf Dingbats
PCL ITC Zapf Dingbats
PS ITC Zapf Dingbats
OCR-B
Typeface / Symbol Set
PSMATH
PIFONT
MSPUBL
MATH8
109Y
209Y
19M
15U
15Y
6M
5M
8M
6J
3K
0O
1O
9Y
Clarendon Condensed Bold ✘
Marigold ✘
Coronet ✘
Helvetica ✘
Helvetica Italic ✘
Helvetica Bold ✘
Helvetica Bold Italic ✘
Helvetica Narrow ✘
Helvetica Narrow Italic ✘
Helvetica Narrow Bold ✘
Helvetica Narrow Bold Italic ✘
Palatino Roman ✘
Palatino Italic ✘
Palatino Bold ✘
Palatino Bold Italic ✘
ITC Bookman Light ✘
ITC Bookman Light Italic ✘
ITC Bookman Demi ✘
ITC Bookman Demi Italic ✘
ITC Avant Garde Book ✘
ITC Avant Garde Book Oblique ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.
this font is not supported or this font does not support this symbol set.

Ventura ITC Zapf Dingbats
PCL ITC Zapf Dingbats
PS ITC Zapf Dingbats
OCR-B
Typeface / Symbol Set
PSMATH
PIFONT
MSPUBL
MATH8
109Y
209Y
19M
15U
15Y
6M
5M
8M
6J
3K
0O
1O
9Y
ITC Avant Garde Demi ✘
ITC Avant Garde Demi Oblique ✘
Century Schoolbook Roman ✘
Century Schoolbook Italic ✘
Century Schoolbook Bold ✘
Century Schoolbook Bold Italic ✘
ITC Zapf Chancery Medium Italic ✘
CourierPS ✘
CourierPS Oblique ✘
CourierPS Bold ✘
CourierPS Bold Oblique ✘
Times Roman ✘
Times Italic ✘
Times Bold ✘
Times Bold Italic ✘
Helvetica Light ✘
Helvetica Light Oblique ✘
Helvetica Black ✘
Helvetica Black Oblique ✘
Line Printer 16 ✘
POSTNET Barcode ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.
this font is not supported or this font does not support this symbol set.

Ventura ITC Zapf Dingbats
PCL ITC Zapf Dingbats
PS ITC Zapf Dingbats
OCR-B
Typeface / Symbol Set
PSMATH
PIFONT
MSPUBL
MATH8
109Y
209Y
19M
15U
15Y
6M
5M
8M
6J
3K
0O
1O
9Y
C39 Narrow ✘
C39 Regular ✘
C39 Wide ✘
OCR-A ✘
OCR-B ✘
Wingdings ✘
Symbol ✘
SymbolPS ✘
ITC Zapf Dingbats ✘
Indicates Typeface supports the specified Symbol Set. ✘ Indicates Typeface does not support the specified Symbol Set.
this font is not supported or this font does not support this symbol set.

All fonts that support the Roman-8 (8U) symbol set also support the following 19 symbol sets.
Symbol Set ID Symbol Set / Typeface

Command Structure
This section introduces the different types of PCL emulation commands and their structure, or syntax. It also demonstrates how you can link commands to abbreviate them.
Control Codes are single-character instructions.
Code Dec Hex Function Result
BS 8 08 Backspace Moves the cursor toward the left margin one horizontal space equal to the last printed character
HT 9 09 Horizontal Tab Moves the cursor to the next defined tab stop
LF 10 0A Line Feed Advances the cursor to the same horizontal position on the following line as determined by either the Vertical Motion Index (VMI) or Set Line Spacing command
FF 12 0C Form Feed Advances the cursor to the same horizontal position at the top margin of the next page
CR 13 0D Carriage Return Moves the cursor to the left margin
SP 32 20 Space Moves the cursor to the right one column
SI 15 0F Primary Font Selects the primary font
SO 14 0E Secondary Font Selects the secondary font
PCL commands are multibyte strings (also known as “escape sequences”) that begin with the Escape control code (ESC, ←, decimal 27, or hexadecimal 1B). The ESC control code notifies the printer that the characters that follow are to be interpreted as part of a command and are not control codes or data to be printed.

Most PCL emulation commands have the following structure:
ESC & a # C
Spaces have been added to this example for readability. The command parameter variables are indicated by a number sign (#).
ESC Decimal 27 or hex 1B
& Parameterized character from American National Standard Code for Information Interchange (ASCII) table (range 33 to 47 decimal)
a Group character from ASCII table (range 96 to 126 decimal) that specifies a group type of control
# Decimal character string value within specified numeric ranges; may be preceded by a + or – sign and contain a decimal point
C Termination character from ASCII table (range 64 to 94 decimal)
A command parameter sets the value for a command. This value stays constant until either a different value resets the command or a command resets the printer to the default values. For example, after the printer receives a command that selects a right margin beginning at column 63, the right margin of each printed page begins at column 63. That margin stays constant until a right margin command with a different value resets it or until the printer is reset.
Parameters for each command are listed in the command tables beginning on page 2-62. Use the Symbol Set Tables to determine the decimal or hexadecimal value for each parameter. To determine a decimal or hex value, first locate the value of the parameter you require in the Symbol Set Table. The decimal value is the value shown in the bottom of the cell or box with that parameter. To find a hex value, go straight up the grid from the desired parameter and read the value in the top heading. This is the first character of the hex value. Next, go straight across the grid to the left of the parameter and read the value in the left column heading. This is the second character of the hex value. For example, ESC (←) is coded 1B in Hex and 27 in decimal. (Any one of the three values ←, 1B, or 27 might be used in your application. Read your documentation to determine which to use.) The example on the following page sets the pitch of the primary font to 16.66 characters per inch.
Element Description

Example:
ESC(s16.66H
Use the plus symbol (+) or the minus symbol (–) to select a position relative to the current cursor position. For example:
ESC&a6C Move to horizontal cursor position, column six
ESC&a+6C Move six columns to the right of the current position
ESC&a-6C Move six columns to the left of the current position
You can combine PCL emulation commands by linking them if the first 3 bytes of the commands are identical. The combined, short form sends the first 3 bytes only once in the string. To combine commands:
For example, notice that the first 3 bytes of these two commands are the same:
ESC(s10H Select 10 characters per inch
ESC(s4099T Select Courier typeface
To combine these two commands, use this form:
which is 3 bytes shorter than the long form:
ESC(s10HESC(s4099T
You can combine more than two commands; for example, you can add Select Stroke Weight Bold (ESC(s3B) to the previous two commands:
or in the long form:
ESC(s10HESC(s3BESC(s4099T
ESC(s10h4099T · ESC(s10h3b4099T

PCL Emulation Commands
See the following tables for a listing of the commands grouped by function.
To determine which commands your printer supports, see “Table A-1: PCL Emulation Commands” on page A-1.
Command / Parameters Function / Result
ESCE Printer Reset
Number of Collated Copies
0 = Collation off
Turns collation of pages off or sets the number of collated copies.
1 ... 999 (number of Copies)
# = number of Copies (1 to 32767)
Affects the page currently in process and subsequent pages.
0 Single-Sided (Default) 1 Duplex Long-Edge Binding 2 Duplex Short-Edge Binding 100 Manual Duplex First Sides 101 Manual Duplex Second Sides
Long-edge or short-edge binding refers to the side of the physical page where binding occurs.
# = number of Decipoints
Also known as Left Offset.
Range = -32767 to 32767
Adjusts placement of logical page along the width of the physical page.
(1 Decipoint = 1/720 inch)
# = number of Decipoints
Also known as Top Offset.
Range = -32767 to 32767
Adjusts placement of logical page along the length of the physical page.
(1 Decipoint = 1/720 inch)

Command / Parameters Function / Result
Range = (96, 100, 120, 144, 150, 160, 180, 200, 225, 240, 288, 300, 360, 400, 450, 480, 600, 720, 800, 900, 1200, 1440, 1800, 2400, 3600, 7200)
Sets the size for the PCL Unit (units per inch).
The Unit of Measure defines the unit used in the following commands:
Default = 300 units per inch
The Unit of Measure also affects the rounding of character escapements and the Horizontal Motion Index.
ESC%–12345X Universal Exit Language (UEL) / Start of PJL
This command terminates the current printer language and allows switching into PJL. For more information, see “UNIVERSAL EXIT LANGUAGE Command” on page 3-2.
ESC&u#D · Unit of Measure

Command / Parameters Function / Result
Selects the physical size of the paper, which also determines the logical page dimensions. See the tables beginning on page 2-4 for the paper and envelope dimensions your printer supports.
1 Executive 2 Letter 3 Legal 4, 10 Folio 6, 11 Ledger (11 x 17) 13, 25 A5 Paper 15 Statement 26 A4 Paper 27 A3 Paper 12, 45 B5 Paper 46 B4 Paper 101 Custom Paper/Universal
If the requested page size is not in the requested source or if no source is requested, sources are checked for the requested size in the following order: multipurpose feeder, tray 1, tray 2, tray 3, tray 4, tray 5, and envelope feeder.
80 Monarch 7 3/4 81 Commercial 10 89 Commercial 9 90 DL 91 C5 99, 100 B5 Envelope 600 Other Envelope
0 Active Source or Eject Page 1 Tray 1 (Default) 2 Manual Paper Feed 3 Manual Envelope Feed 4 Tray 2 5 Tray 3 6 Optional Envelope Feeder 7 Auto Select 8 Multipurpose Feeder 20 Tray 4 21 Tray 5 62 Optional Paper Source
Selects the paper feed source.
# = number of Decipoints
Sets the width of the Universal size in decipoints.
(1 Decipoint = 1/720 inch)
# = number of Decipoints
Sets the height of the Universal size in decipoints.
(1 Decipoint = 1/720 inch)

Command / Parameters Function / Result
Set Universal Feed Direction
0 Short-edge 1 Long-edge
Sets the feed direction of Universal size. Feed direction means which side of the print media, either the short edge or the long edge, feeds first through the printer first.
ESC&f#W [custom name]
Set Universal Custom Name
# = number of bytes in the custom name
Sets the user-specified custom name for the Universal paper size being used.
0 Portrait (Default) 1 Landscape 2 Reverse Portrait 3 Reverse Landscape
Specifies the position of the logical page with respect to the physical page.
# = Degrees (0, 90, 180, 270)
Rotates coordinate system counter-clockwise in 90° increments with respect to current orientation.
Character Text Path Direction
0 Horizontal Printing -1 Vertical Rotated Printing
Vertically rotates text for use in vertical writing, such as printing Japanese text.
Sets left margin to left edge of the designated column.
Sets right margin to right edge of the designated column.
Default = Logical Page Width
ESC9 Clear Horizontal Margins
Clears left and right margins.
# = number of Lines
Sets the number of lines between the top of the physical page and first line of print. Line height is determined by the current Vertical Motion Index (VMI) and/or line spacing value.
Default = 3 (1/2 inch)
This command is parsed and ignored.

Command / Parameters Function / Result
# = number of Lines
Sets the bottom margin length in lines, measured from the first line of the page.
Default = 60 or 64 (Country specific)
Text Length equals Logical Page Length –1 inch (–1/2 inch for top and –1/2 inch for bottom).
0 Auto Select (uses the active bin) 1 Standard Bin 2 Bin 1 or Rear Bin 3 Bin 1 or Rear Bin 4 Bin 2 5 Bin 3 6 Bin 4 7 Bin 5 8 Bin 6 9 Bin 7 10 Bin 8 11 Bin 9 12 Bin 10
Sets the exit path to direct paper to one of the output bins.
0 Off 1 On (Default)
Perforation area includes the area from the bottom margin of the current page to the top margin of the next page. When skipping perforations, a line feed past the bottom margin ejects a page and places the cursor at the top margin of the next page.
Set Horizontal Motion Index (HMI)
# = number of 1/120 inch increments
Sets the width of all characters for fixed-space fonts. Sets only the width of the space for proportional spaced fonts.
(Valid to 4 decimal places)
Set Vertical Motion Index (VMI)
# = number of 1/48 inch increments
Sets Vertical Motion Index in 1/48 inch increments. The VMI determines the vertical distance between lines.
(Valid to 4 decimal places)

Command / Parameters Function / Result
Set Line Spacing (Alternative Method)
1 1 line/inch 2 2 lines/inch 3 3 lines/inch 4 4 lines/inch 6 6 lines/inch (Default) 8 8 lines/inch 12 12 lines/inch 16 16 lines/inch 24 24 lines/inch 48 48 lines/inch
Specifies VMI in lines per inch.
Duplex Page Side Selection
0 Next Side 1 Front Side 2 Back Side
Specifies which physical page side to print next when duplex printing.
# = number from 0 to 14 0 = default page length is used (1 to 14 new page length is set)
Sets the logical page length in number of lines.
5 Turn Text Scale Mode OFF 6 Turn Text Scale Mode ON
Allows 66 lines of text at six lines per inch to print on an effective page length of 10 1/2 inches.

Command / Parameters Function / Result
ESC&n#W [operation] [string]
# = number of data bytes that make up the operation and string
Selects the media type using a character string. The string ID is case sensitive and may be up to 511 bytes long.
The string ID specifies the media type requested.
operation = 100 or 1 byte = 0x64 or 'd' ascii
Media Type Alphanumeric String
For example:
Plain Paper Plain Bond Bond Transparency Transparency Card Stock Card Stock Labels Labels Letterhead Letterhead Pre-printed Preprinted Colored Paper Color Envelope Envelope Custom Type 1 Custom Type 1 or User Type 1 Custom Type 2 Custom Type 2 or User Type 2 Custom Type 3 Custom Type 3 or User Type 3 Custom Type 4 Custom Type 4 or User Type 4 Custom Type 5 Custom Type 5 or User Type 5 Custom Type 6 Custom Type 6 or User Type 6
string = See Alphanumeric String list at right
For example, the following shows the command and parameters used to select bond paper: ESC&n5WdBond
Command / Parameters Function / Result
Horizontal Cursor Position (in Columns)
# = number of Columns1
Moves the cursor to a new position along the horizontal axis.
Horizontal Cursor Position (in Decipoints)
# = number of Decipoints1
Moves the cursor to a new position along the horizontal axis.
(1 Decipoint = 1/720 inch)
Horizontal Cursor Position (in PCL Units)
# = number of PCL Units1
Moves the cursor to a new position along the horizontal axis.
1 Parameter preceded by + or – sign denotes a relative cursor move from the current cursor position. Parameter without a sign denotes an absolute cursor move from the top left margin.

Command / Parameters Function / Result
Vertical Cursor Position (in Rows)
# = number of Rows1
Moves the cursor to a new position along the vertical axis.
Vertical Cursor Position (in Decipoints)
# = number of Decipoints1
Moves the cursor to a new position along the vertical axis.
(1 Decipoint = 1/720 inch)
Vertical Cursor Position (in PCL Units)
# = number of PCL Units1
Moves the cursor to a new position along the vertical axis.
ESC= Half Line-Feed
Moves the cursor down 1/2 line (1/2 of the current VMI).
0 CR=CR, LF=LF, FF=FF (Default) 1 CR=CR+LF, LF=LF, FF=FF 2 CR=CR, LF=CR+LF, FF=CR+FF 3 CR=CR+LF, LF=CR+LF, FF=CR+FF
Controls how the printer responds to the Carriage Return (CR), Line Feed (LF), and Form Feed (FF) control codes.
Push / Pop Cursor Position
0 Push 1 Pop
Sets up a cursor position stack for storing and recalling various cursor positions. The stack can store up to 20 cursor positions.
1 Parameter preceded by + or – sign denotes a relative cursor move from the current cursor position. Parameter without a sign denotes an absolute cursor move from the top left margin.

parameters set following the best fit selection rules.
Command / Parameters Function / Result
See “Font and Symbol Set Support for the Lexmark X422” on page 2-9, or “Font and Symbol Set Support for the Lexmark C510(n)” on page 2-19 for more information.
# = symbol set ID
Default = 10U (PC-8) or 12U (PC-850), [Country specific]
Selects a font with proportional or fixed spacing.
0 Fixed (Default) 1 Proportional
Selects the number of characters per inch (cpi) for a fixed-space bitmapped or monospaced scalable font. Valid to 2 decimal places.
# = characters per inch
Height (Select Point Size)
Sets the font height in points. Valid to 2 decimal places.
# = height in points (.25 to 999.75)
Identifies the physical traits of a character and the composition of the font symbols.
0 Upright (Default) 1 Italic 4 Condensed 5 Condensed Italic 8 Compressed 24 Expanded 32 Outline 64 Inline 128 Shadowed 160 Outline Shadowed

Command / Parameters Function / Result
Selects a font with a particular thickness.
-7 Ultra Thin -6 Extra Thin -5 Thin -4 Extra Light -3 Light -2 Demi Light -1 Semi Light 0 Medium (Default) 1 Semi Bold 2 Demi Bold 3 Bold 4 Extra Bold 5 Black 6 Extra Black 7 Ultra Black
Selects the best fit font design.
# Typeface identifier (0 - 65535)
To obtain the typeface values for downloaded fonts, print the font list from the printer operator panel or through MarkVision Professional. Refer to your printer user documentation for more information.
On the printout, the typeface number is the last number on the font selection command example line. The example line is below the name of the font. In the following example, the typeface number is underlined:
RO Courier ((s0ph0s0b4099T
Select Font by Font ID
Selects the font by the identification number.
# = Font ID (0 - 32767)
Sets all font selection characteristics to the Default Font.
# = number of data of bytes to print as text
Prints the next number of bytes as text.
Select Underline Type (Enable)
0,1 Fixed 2 Fixed - double 3 Floating 4 Floating - double
ESC&d@ Underline - Disable

Command / Parameters Function / Result
0, 1 1 byte characters 21 1 or 2 byte characters 31 1 or 2 byte characters 38 1 or 2 byte characters 1008 1, 2, or 3 byte characters (UTF-8)
Communicates to the PCL parser whether character codes are interpreted as 1-byte or 2-byte character codes.
Select Primary and Secondary Pitch
0 10.00 cpi 2 16.66 cpi 4 12.00 cpi
Selects the pitch for the primary and secondary font.
Command / Parameters Function / Result
Symbol Set ID Code
# = Symbol Set ID (0 - 32767)
Sets the symbol set identification for the symbol set downloaded.
# = number of data bytes
Contains the data for the user-defined symbol sets.
0 Delete all (temporary and permanent) 1 Delete all temporary 2 Delete current (ID) 4 Make current temporary 5 Make current permanent
Manages user-defined symbol sets.

Command / Parameters Function / Result
# = Font ID # (0 - 32767)
Sets the identification number for the font being downloaded.
# = number of data bytes
Downloads soft font header information.
0 Delete all (temporary and permanent) 1 Delete all temporary 2 Delete previous font ID 3 Delete previous specified character 4 Make previous font ID temporary 5 Make previous font ID permanent 6 Copy current font
Manages soft fonts.
# = Code Point (0 - 65536)
Sets the decimal code point associated with the next character downloaded or deleted.
# = number of data bytes
Downloads character descriptor and data to the current character code.
Command / Parameters Function / Result
# = Macro ID (0 - 32767)
Sets the ID for the macro you have created on flash or disk.
0 Start definition 1 End definition 2 Execute macro (previous macro ID) 3 Call macro (previous macro ID) 4 Enable overlay (previous macro ID) 5 Disable overlay 6 Delete all macros 7 Delete all temporary macros 8 Delete current macro ID 9 Make last ID temporary 10 Make last ID permanent
Manages use of macros.
See “Macros” on page 2-95 for additional information.

Command / Parameters Function / Result
Selects pattern used to fill a rectangular area.
0 White (default) 1-2 2% gray 3-10 10% gray 11-20 15% gray 21-35 30% gray 36-55 45% gray 56-80 70% gray 81-99 90% gray 100 100% gray (Black)
1 Horizontal line 2 Vertical line 3 Diagonal line 4 Diagonal line 5 Square grid 6 Diagonal grid
# = User-Defined Pattern ID
0 Transparent (Default) 1 Opaque
Affects copying of white pixels from the source onto the destination image.
0 Transparent (Default) 1 Opaque
Affects copying of white pixels from the pattern onto the destination image.
# = logical operation, value (0 to 255)
Defines boolean operations to be performed on data already printed and data about to be printed.
0 Grid Intersection (Default) 1 Grid Centered
Determines how pixels are placed for a rectangular area fill and GL/2 objects.
Pixel Placement does not affect text or raster images.
0 Solid Black (Default) 1 Solid White 2 Gray Shading Pattern 3 Cross-Hatch Pattern 4 User Defined Pattern 9 True gray Level Fill
Selects pattern used when printing text and raster images.

Command / Parameters Function / Result
# = number of data bytes
Downloads binary pattern data.
Set Pattern Reference Point
0 Rotate with print (Default) 1 Fixed
Sets pattern reference point to the current cursor position for user- defined patterns.
0 Delete all patterns (temporary and
Manages use of user-defined patterns.
permanent) 1 Delete all temporary patterns 2 Delete pattern (last ID specified) 4 Make pattern of last ID # temporary 5 Make pattern of last ID # permanent
Command / Parameters Function / Result
Horizontal Rectangle Size (in Decipoints)
# = Number of Decipoints (0 - 32767)
Specifies the rectangle width in decipoints.
(1 Decipoint = 1/720 inch)
Default = 0, valid to 4 decimal places
Horizontal Rectangle Size (in PCL Units)
# = Number of PCL Units (0 - 32767)
Specifies the rectangle width in PCL units.
Vertical Rectangle Size (in Decipoints)
# = Number of Decipoints (0 - 32767)
Specifies the rectangle height in decipoints.
(1 Decipoint = 1/720 inch)
Default = 0, valid to 4 decimal places
Vertical Rectangle Size (in PCL Units)
# = Number of PCL Units (0 - 32767)
Specifies the rectangle height in PCL units.

Command / Parameters Function / Result
Selects pattern used to fill rectangle area.
0 White (default) 1-2 2% Gray 3-10 10% Gray 11-20 15% Gray 21-35 30% Gray 36-55 45% Gray 56-80 70% Gray 81-99 90% Gray 100 100% Gray (Black)
1 Horizontal Line 2 Vertical Line 3 Diagonal Line 4 Diagonal Line 5 Square Grid 6 Diagonal Grid
# = User-Defined Pattern ID
0 Black Fill (Default) 1 White Fill 2 Gray Fill 3 Pre-Defined Cross-Hatch Pattern Fill 4 User-Defined Pattern 5 Current Pattern Fill 9 True gray Level Fill
Fills a rectangular area defined by Horizontal and Vertical Rectangle Sizes with selected pattern.

Command / Parameters Function / Result
75 75 dpi 100 100 dpi 150 150 dpi 200 200 dpi 300 300 dpi 600 600 dpi 1200 1200 dpi
0 Rotate with print 3 Fixed (Default)
Sets the Raster Image Orientation in relation to the logical page.
# = Number of Input Pixels
Sets width of clip window for raster graphics.
# = Number of Raster Lines
Sets height of clip window for raster graphics.
0 Left Graphics Margin at 0 (Default) 1 Current Cursor Position 2 At logical left page limit with scaling On 3 At current cursor position with scaling On
Sets the left margin for raster graphics.
Transfer Raster Data by Plane
# = Number of Data Bytes
This command is used when the raster data is encoded by plane as specified by the Simple Color command or the Configure Image Data command. The command sends each plane in the row except the last.
# = Number of Raster Lines
Moves cursor position down by the specified number of raster lines.

Command / Parameters Function / Result
Set Raster Compression Mode
0 Uncoded (Default) 1 Run-Length Encoded 2 Tagged Image File Format (TIFF) byte 3 Delta Row 5 Adaptive Compression 9 Replacement Delta Row 999 Zlib 1002 Group 4 1003 Group 3 one dimensional 1004 Group 3 two dimensional K=2 1005 Group 3 two dimensional K=4 1006 TIFF word (16 bit) 1007 TIFF double-word (32 bit) 1008 Adaptive compression (includes TIFF word and TIFF double-word)
Identifies the compression mode the host uses to transfer RIG data. For instance, this command can be run-length encoding or TIFF encoding.
Transfer Raster Data by Row/Block
# = Number of Data Bytes
Transfers RIG data.
ESC*rB End Raster Graphics (Version B)
Signals end of raster graphics transfer. If a Raster Height is specified, the cursor is moved to the first raster row past the Raster Height.
ESC*rC End Raster Graphics (Version C)
Same as Version B, but:
ESC*t#H Raster Width (Destination)
Sets the width of the destination raster.
ESC*b#M · ESC*b#W[data]

Command / Parameters Function / Result
ESC*t#V Raster Height (Destination)
Sets the height of the destination raster.
Sets the configuration of the destination raster.
# - 8 (K-only) or 26 (KCMY)
Byte 0 - 0x02 (constant)
Byte 1 - number of colors
0x01 - K only
Byte 2,3 - X res for K plane
0x012C (300) or 0x0258 (600)
Byte 4,5 - Y res for K plane
0x012C (300) or 0x0258 (600)
Byte 6,7 - K plane intensity levels
0x02 (1 bit/plane) or 0x04 (2 bits/plane)
Byte 8,9 - X res for C plane
0x012C (300) or 0x0258 (600)
Byte 10,11 - Y res for C plane
0x012C (300) or 0x0258 (600)
Byte 12,13 - C plane intensity levels
0x02 (1 bit/plane) or 0x04 (2 bits/plane)
Byte 14,15 - X res for M plane
0x012C (300) or 0x0258 (600)
Byte 16,17 - Y res for M plane
0x012C (300) or 0x0258 (600)
Byte 18,19 - M plane intensity levels
0x02 (1 bit/plane) or 0x04 (2 bits/plane)
Byte 20,21 - X res for Y plane
0x012C (300) or 0x0258 (600)
Byte 22,23 - Y res for Y plane
0x012C (300) or 0x0258 (600)
Byte 24,25 - Y plane intensity levels
0x02 (1 bit/plane) or 0x04 (2 bits/plane)
![Page 92 of the Lexmark Printer user manual — ESC * l #W[data]](/cdn/reader/75/7538781613ebc5cd24e1081047fb959492f200c822e50809a572d2415f265acb/images/page-92.webp?w=400)
Command / Parameters Function / Result
0 Print in mixed render algorithm mode 1 Print using gray scale equivalent
Changes each color value to its gray scale equivalent.
0 Delete all palettes except those in stack (active palette is deleted) 1 Delete all palettes in stack (active palette not affected) 2 Delete palette specified by Palette Control ID 6 Copy active palette to ID specified by Palette Control ID
Provides palette management.
0 to 32767 Palette ID number
Indicates the ID number used by the Palette Control command.
0 to 32767 Palette ID number
Selects a new active palette by indicating the ID number.
0 Resets or initializes the color lookup tables for each primary color to the unity curve 770, Data Data for color lookup table
Enables the color lookup tables and specifies the table to use.
7 to 32767, Data Data size and data of byte-aligned binary data that specifies a matrix or matrices for the primary colors
Downloads a device dependent user-defined dither matrix.
1 to 32767, Data Specifies lightness, saturation, and image scaling
Indicates the lightness, saturation, and scaling algorithm to be applied to a job.
0 Push (Save) Palette 1 Pop (Restore) Palette
Saves (push) the current palette and then restores (pop) it from the palette stack.
-4 4 planes, device KCMY palette -3 3 planes, device CMY palette 1 Single plane, K (black) palette 3 3 planes, device RGB palette
Creates a fixed-size palette. The color specification of the palette cannot be modified.

Command / Parameters Function / Result
0 Gamma Correction Off 0.0 to 4.0 Gamma Number
Improves the perceptual correctness of color data sent from the monitor to any other non-linear device by adjusting the brightness and darkness.
ESC*t#J Render Algorithm
Selects the algorithm used for dithering images and fills.
-32767.0 to 32767.0
Indicates the first primary color specified by the Assign Color Index command.
-32767.0 to 32767.0
Indicates the second primary color specified by the Assign Color Index command.
-32767.0 to 32767.0
Indicates the third primary color specified by the Assign Color Index command.
# = Palette Index
Designates the three current color components to the specified palette index number. n represents the number of bits per index.
0 to 2n – 1 = Palette Index
# = Palette Index
Sets the foreground color to the specified index in the current palette. n represents the current palette size.
0 to 2n – 1 = Palette Index
ESC*v#W[data] Configure Image Data
Creates programmable palettes.
ESC*i#W[data] Viewing Illuminant
Designates the relative white point used in determining a viewing illuminant condition.

Command / Parameters Function / Result
Set Status Readback Location Type
0 Invalid location (Default) 1 Use currently selected location 2 All locations 3 Internal (resident) 4 Downloaded entity 5 Cartridge 7 User-installable flash 200 Disk
Sets the status location type to the specified value.
The 5 value for Cartridge may be specified, but since your printer does not support font cards or cartridges, the command is ignored.
The 7 value for User-installable flash is only valid when flash memory is installed.
The 200 value is only valid when a hard disk is installed.
Set Status Readback Location Unit
0 All 1 If download, temporary; otherwise, highest priority 2 If download, permanent; otherwise, next higher priority
Sets the status location unit to the specified value.
The location unit is used along with the location type to identify a location for the Inquire Status Readback Entity command.
Inquire Status Readback Entity
0 Font 1 Macro 2 User-defined pattern 3 Symbol set (for unbound scalable fonts) 4 Font extended
Returns the requested information set by Set Status Readback Location Type and Set Status Readback Location Unit.
ESC*s1M Free Space
Returns the total available memory and the largest available block of memory.
0 Flush all complete pages 1 Flush all pages
Holds print jobs in the print buffer until the current job finishes printing.
Returns # back to host computer.

Command / Parameters Function / Result
Picture Frame Horizontal Size (in Decipoints)
Specifies the horizontal dimension of the picture frame used when printing a GL/2 plot.
(1 Decipoint = 1/720 inch)
Picture Frame Vertical Size (in Decipoints)
Specifies the vertical dimension of the picture frame used when printing a GL/2 plot.
(1 Decipoint = 1/720 inch)
Set Picture Frame Anchor Point
0 Set Anchor Point to Cursor Position
Sets the position of the picture frame anchor point to the cursor position. The picture frame anchor point defines the location of the upper left corner of the picture frame.
GL/2 Horizontal Plot Size
Specifies the horizontal scaling factor used when importing an image into the picture frame.
GL/2 Vertical Plot Size
Specifies the vertical scaling factor used when importing an image into the picture frame.
0 Use Previous GL/2 Pen Position 1 Use Current PCL Cursor Position
Exits PCL emulation and uses GL/2 commands to print.
0 Use Previous PCL Cursor Position 1 Use Current GL/2 Pen Position
Exits GL/2 mode and uses PCL emulation commands to print.
Command / Parameters Function / Result
0 Enable 1 Disable (Default)
Enabling End-Of-Line Text Wrap moves portions of lines that extend into the unprintable area to the next line. Disabling drops the portion extending into the unprintable area.
ESCY Display Functions On
Prints all control codes and escape sequences rather than executing them.

Command / Parameters Function / Result
ESCZ Display Functions Off
Turns off Display Functions; resumes normal command processing.
ESCz Print Test Page
Causes a test page to print.
-1 Ink Saver 0 Normal 1 Best
Selects the print quality setting for the page.
0 Plain Paper 1 Bond 2 Coated Paper 3 Glossy Paper 4 Transparency 101 Photo Paper 102 Card Stock 103 Labels 104 Envelope 105 Letterhead 106 Preprinted 107 Colored Paper 108 Iron On
Selects the paper type setting for the page.
PCL emulation and cannot be used with software without a unique printer driver written explicitly for GL/2.
The following tables list the GL/2 commands by group. To determine which GL/2 commands your printer supports, see “Table A-2: GL/2 Commands” on page A-6.
Command / Parameter Command Name
IP (XP1, YP1(, XP2, YP2)); Input P1 and P2

Command / Parameter Command Name
IR (XP1, YP1(, XP2, YP2)); Input Relative P1 and P2
IW (X1, Y1, X2, Y2); Input Window
MC (mode(, opcode)); Logical Operation
PP (mode); Pixel Placement
RO (angle); Rotate Coordinate System
SC (Xmin, Xmax, Ymin, Ymax(, type(, left, bottom))); Scale
Command / Parameter Command Name
AA Xcenter, Ycenter, sweep_angle(, chord_angle); Arc Absolute
AR Xcenter, Ycenter, sweep_angle(, chord_angle); Arc Relative
AT Xinter, Yinter, Xend, Yend(, chord_angle); Absolute Arc Three Point
BR X1, Y1, X2, Y2, X3, Y3(,...); Bezier Relative
BZ X1, Y1, X2, Y2, X3, Y3(,...); Bezier Absolute
CI radius(, chord_angle); Circle
PA (X, Y(,...)); Plot Absolute
PD (X, Y(,...)); Pen Down
PE (flag(value) | coordinates (...)); Polyline Encoded
PR (X, Y(,...)); Plot Relative
PU (X, Y(,...)); Pen Up
RT Xincr inter, Yincr inter, Xincr end, Yincr end(, chord_angle); Arc Relative Three Point
WU (type); Pen Width Units
Command / Parameter Command Name
EA X, Y; Edge Rectangle Absolute
ER X, Y; Edge Rectangle Relative
EW radius, start_angle, sweep_angle(, chord_angle); Edge Wedge
FP (0); Fill Polygon, Odd/Even
FP 1; Fill Polygon, Non-Zero Winding
PM (mode); Polygon Mode
EP; Edge Polygon

Command / Parameter Command Name
RA X, Y; Fill Rectangle Absolute
RR X, Y; Fill Rectangle Relative
WG radius, start_angle, sweep_angle(, chord_angle); Fill Wedge
Command / Parameter Command Name
AD (kind, value(,...)); Define Alternate Font
CF (mode(, pen)); Character Fill
CP (spaces, lines); Character Plot
DI (run, rise); Absolute Direction
DR (run, rise); Relative Direction
DT (label_terminator(, mode)); Define Label Terminator
DV (path(, line)); Define Variable Text Path
ES (width(, height)); Extra Space
FI font_ID; Primary Font
FN font_ID; Secondary Font
LB char...char label_terminator; Label
LM (mode,[row number]) Label Mode
LO (position); Label Origin
LO 21; Uses PCL Label Origin
SA; Select Alternate Font
SB (mode); Scalable or Bitmapped Fonts
SD (kind, value(,...)); Define Standard Font
SI (width, height); Absolute Character Size
SL (tangent); Character Slant
SR (width, height); Relative Character Size
SS; Select Standard Font
TD (mode); Transparent Data

Command / Parameter Command Name
AC (X, Y); Anchor Corner
CR (red black ref, red white ref, green black ref, green white ref, blue
black ref, blue white ref);
FT (fill_type(, option1(, option2)); Fill Type
FT22, (PCL User-Defined Pattern ID); Fill Type
FT 9, level; Fill Type
LA (kind, value(,...));. Line Attributes
LT (pattern_number(, pattern_length(, mode))); Line Type
NP (number); Number of Pens
PC (pen (, red, green, blue)); Pen Color
PW (width(, pen)); Pen Width
RF (index(, width, height(, pen, ...))); Define Raster Fill
SM (character); Symbol Mode
SP (pen); Select Pen
SV (screen_type(, option1(, option2))); Screened Vectors
SV (9, level,) Screened Vectors
TM (width, height(, number...)); Threshold Matrix
TR (mode); Transparency Mode
UL (index(, gap,...gap)); User Defined Line
WU (type); Pen Width Units
Color Range

Raster Image Graphics
These commands utilize the raster area. Before sending data, set the presentation mode, the resolution, the compression mode, the raster height and width, and start raster graphics. These parameters are in effect until you overwrite them with a different command or there is a printer reset.
To ensure that the printed image appears in the expected area, set width and height parameters.
The Raster Compression Mode command determines how raster data is coded. It affects the amount of code required to create an image, and the efficiency of image printing.
Parameters:
2 Tagged Image File Format (TIFF) Byte
9 Replacement Delta Row
1003 Group 3 one dimensional
1004 Group 3 two dimensional K=2
1005 Group 3 two dimensional K=4
1006 TIFF word (16 bit)
1007 TIFF double-word (32 bit)
1008 Adaptive Compression (includes TIFF word and TIFF double-word)

Descriptions and examples of the different parameters appear on the following pages. Each example draws the same square outline 64 bits (8 bytes) wide by 64 scan lines long.
Uncoded Data is not compressed. Only those bytes needed to form the image are sent. Each bit represents a single dot. In the first byte, bit 7 corresponds to the first dot in the raster row, bit 5 to the third dot, and so forth.
ESC*p300x300Y |Move the cursor to 1" x 1" (1 in. from top margin
and 1 in. from left edge of logical page)
ESC*t100R |Set resolution to 100 dots per inch
ESC*r0F |Rotate image to match current orientation
ESC*b0M |Set compression mode to Uncoded
ESC*r1A |Start raster graphics at current position
ESC*b8W 'FF'x |Raster data uncompressed
ESC*b8W '80 00 01'x
ESC*b8W '80 00 01'x ... |Repeat to provide 64 total scan lines
ESC*b8W '80 00 01'x
ESC*b8W 'FF'x
ESC*rB |End graphics

Run-Length Encoded Data is interpreted in pairs of bytes. The first byte:
ESC*p300x600Y |Move cursor to 1" x 2"
ESC*b1M |Set compression to Run-Length
ESC*r1A |Start raster graphics at current position
ESC*b6W '0080 0500 0001'x |1x'80'x, 6x'00'x, 1x'01'x
ESC*b6W '0080 0500 0001'x |1x'80'x, 6x'00'x, 1x'01'x ... |...
ESC*b6W '0080 0500 0001'x |1x'80'x, 6x'00'x, 1x'01'x
ESC*b2W '07FF'x |8x'FF'x
ESC*rB |End graphics
TIFF “Packbits” contain a control byte (a signed number) that indicates whether the raster data bytes are to be repeated (up to 127 times) or printed as encoded data.
ESC*p300x900Y |Move cursor to 1" x 3"
ESC*b2M |Set compression to TIFF
ESC*r1A |Start Raster Graphics at current position
ESC*b6W '0080 FB00 0001'x |1:'80'x, 6x'00'x, 1: '01'x or
ESC*b9W '078000000000000001'x |8: '8000000000000001'x ... |...
ESC*b6W '0080 FB00 0001'x |1:'80'x, 6x'00'x, 1: '01'x
ESC*b2W 'F9FF'x |8x'FF'x
ESC*rB |End graphics

Delta Row is a compression mode that identifies and transmits only those bytes different from the ones in a preceding row. The control byte consists of two parts:
ESC*p300x1200Y |Move cursor to 1" x 4"
ESC*b3M |Set compression to Delta Row
ESC*r1A |Start raster graphics at current position |Num Offset
ESC*b9W 'E0FFFFFFFFFFFFFFFF'x |'111 00000'b=8 at 0: 'FFFFFFFFFFFFFFFF'x
ESC*b9W 'E08000000000000001'x |8 at 0: '8000000000000001'x
ESC*b0W |No bytes change ...
ESC*b0W |No bytes change
ESC*b9W 'E0FFFFFFFFFFFFFFFF'x |8 at 0: '8FFFFFFFFFFFFFF'x
ESC*rB |End graphics

Adaptive compression allows the combined use of compression methods 0 through 3 (Uncoded, Run-Length Encoded, TIFF, and Delta Row). It also allows the printing of empty rows (all zeros) or duplicate rows.
Scan Mode CountH,CountL Data
0 Data sizeH,L Uncoded raster scan data
1 Data sizeH,L Size of Run-length encoded data (high,low)
2 Data sizeH,L Size of Tagged Image File Format (TIFF) data (high,low)
3 Data SizeH,L Size of Delta Row data (high,low)
4 NumberH,L of empty rows
5 NumberH,L of duplicate rows
254 Data SizeH,L TIFF word
255 Data SizeH,L TIFF double-word
ESC*p300x1500Y |Move cursor to 1" x 5"
ESC*b5M |Set the compression to Adaptive Compression
ESC*b29W |Raster Data: 29 bytes follow '03 0009'x 'E0FFFFFFFFFFFFFFFF'x | Delta Row: 8 at 0: 'FFFFFFFFFFFFFFFFh'x '01 0006'x '0080 FB00 0001'x | Run Length: 1:'80'x, 6x'00'x, 1:'01'x '05 0035'x | Duplicate rows: 61 times '02 0002'x 'F9FF 'x | TIFF: 8x'FF'x
ESC*rB |End graphics
None · None

Zlib is a generic compression method. It refers to a standard for compression as well as the library that implements the standard.
The zlib compression method uses the deflate algorithm. This same algorithm is used by more widely known compression utilities such as PKZIP and GZIP.
Compressed data is a series of variably-sized blocks. An encoder determines how to break the data into blocks and finds the best compression method to use for each block.
An encoder works based on the following principles. The encoder creates a dictionary containing different characters in a set of data. Short strings of bits represent more commonly occurring characters, and long strings of bits represent less frequently used characters. A probability tree determines which characters are frequently used. Repeated patterns in a string of characters are identified and stored, so the string doesn’t have to be stored multiple times.
A three-bit zlib header is added to the beginning of a block to describe the type of compression used and indicates whether the block is a final block. Other information in the header includes checksums, compression algorithm used, and the level of compression. In compression all checksums are set to zero and in decompression the checksums are ignored.
The memory required for zlib compression and decompression is independent of the size of the data to be compressed or decompressed.
The number 999 does not conflict with other compression types, so it is used to represent zlib compression. See page 2-88 for more information.
Since Group 4 images do not use line endings, the width of the image must be specified using the Raster Width command (ESC*r#S).
The compressed image data is sent to the printer using the Transfer Raster Data command (ESC*b#W). The maximum number of bytes that can be sent using the Transfer Raster Data command is 32K bytes. Images larger than 32K bytes must be broken up and sent using multiple commands. It does not matter where the image is broken, or how many Transfer Raster Data commands are used. Once the image is started (with a Transfer Raster Data command), no other commands are allowed until the entire image has been sent.

The following example prints a Group 4 image file that is 256 bits wide and 9,645 bytes long:
ESC*b1002M |Set Raster Compression to Group 4
ESC*r256S |Define width of image in input bits
ESC*r1A |Start Raster Graphics at current position
ESC*b9645W |9,645 bytes of a Group 4 image ...[Group 4 image data]...
ESC*rB |End Raster Graphics
All lines of data must be the same length. If they are not, zeroes (0) must be added to attain the same length.
beyond the raster width specified in the Raster Width command (ESC*r#S), the image is clipped at print time.
When the compression mode is 1008 (Lexmark Adaptive), TIFF word and double- word can be printed using compression scan modes 254 and 255 respectively. This compression method sends a raster image as a block of raster data.

Macros
When creating a macro, first assign it an ID number. If this number is identical to an existing macro ID in RAM, the old macro is deleted when you specify the Macro Control Start Definition. Next, start the macro definition, send the contents of the macro, and stop the macro definition.
(nesting), a macro cannot be defined within another macro definition. Each macro must be defined separately.
This example creates a macro to print the Wigit Corp. logo, then calls the logo macro in the body of a letter.
ESC&f1Y |Set the macro ID to 1
ESC&f0X |Start the macro definition
ESC&a+72H |Relative move right 1/10 inch (+72/720th)
ESC(8U |Select Roman-8 symbol set
ESC(s1p18v0s3b4101T |Select CG Times 18 point bold W |Print W
ESC&a-21.6H |Relative move left 0.03 inch
ESC(s12v1S |Select (CG Times) 12 point (bold) italic igit |Print igit
ESC&a+72H |Relative move right 1/10 inch
ESC(s18v0S |Select 18 point and turn off italic C |Print C
ESC(s12v1S |Select 12 point italic orp. |Print orp.
ESC&a+72H |Relative move right 1/10 inch
ESC&f1X |End of macro definition
ESC&f10X |Make Macro ID 1 permanent From: |Print the header From:
ESC&f1y3X |Set the macro ID to 1 and call the macro ... |Print the letter Thank you for ... |Print the closing
ESC&f1y3X |Set the macro ID to 1 and call the macro ...

CHAPTER 3: Printer Job Language
Your printer supports complete Printer Job Language (PJL) commands, including certain commands that cause the printer to enter PCL emulation, PostScript emulation, and Personal Printer Data Stream (PPDS).
To determine which commands your printer supports, see Appendix B: “PJL Support” on page B-1.
The syntax for each supported PJL command is listed in this chapter. The following character codes are used throughout the chapter to illustrate the syntax of each PJL command.
Character Code Description Hex Code Decimal Code
Escape Character 0x1B 27
Line Feed Character 0x0A 10
Carriage Return Character 0x0D 13
Form Feed Character 0x0C 12
Horizontal Tab 0x09 9
Universal Exit Language 0x1B 25 2D 31 32 33 34 35 58

UNIVERSAL EXIT LANGUAGE Command
The Universal Exit Language (UEL) command terminates the current printer language and allows dynamic switching into PJL.
<ESC>%-12345X
Notes:
The PJL commands must immediately follow the UEL command (that is, the X in the UEL syntax must be immediately followed by the @PJL of the next PJL command).

ENTER LANGUAGE Command
This command causes the printer to enter the specified language, such as PCL emulation, PostScript emulation, or PPDS.
@PJL ENTER LANGUAGE = language[]
@PJL ENTER LANGUAGE = PostScript[]
enters PostScript emulation.
This command lets you add descriptive comments to your PJL job.
@PJL COMMENT words[]

Job Separation Commands
Your printer supports the PJL JOB and EOJ commands. When the printer receives a JOB command, the print timeout is multiplied by 10; when the printer receives a PJL EOJ command, the print timeout is reset to the user default. The Waiting message appears on the printer operator panel display or through MarkVision Professional until an EOJ command is received or until the print timeout expires.
Your printer also supports the PASSWORD parameter for the PJL JOB command.
The host computer can use the JOB command to separate print data into various parts or jobs. Specifically, the JOB command signifies to the printer the start of a print job. Use the EOJ command to signify the end of a job. In addition, use the JOB/EOJ pair to accomplish the following:
@PJL JOB [NAME = "job name"] [START = first page] [END = last page] [PASSWORD = number][]

NAME = "job name"
Use the NAME parameter to assign a character string name to a particular job. The name may be any combination of printable characters, spaces or horizontal tabs up to a maximum of 80 characters, spaces, or tabs. The job name must be enclosed in double quotes, as indicated by the command syntax.
START = first page
Use the START parameter in conjunction with the END parameter to skip the printing of a particular portion of the job. The emulator discards pages of a job until the page specified by this parameter is reached. The first page range is from 1 to 2,147,483,647. Omission of the START parameter causes the printer to start printing with page 1 of the job.
END = last page
Use the END parameter in conjunction with the START parameter to skip the printing of a particular portion of the job. The emulator discards all pages of a job after the last page has been printed. The specification of last page is relative to page 1 of the print job and its range is from 1 to 2,147,483,647. Omission of the END parameter causes the printer to print all pages to the end of the job.
A system administrator can control which jobs, and therefore which users, are allowed to modify the printer default or NVRAM variables by declaring a PJL password. With a PJL password declared, the PASSWORD parameter with the correct PASSWORD number must be specified in order to modify the default printer environment.
A PJL JOB command with the correct PASSWORD must be issued before any PJL command can modify an NVRAM setting. The PJL EOJ command terminates the job and disables any further modification of NVRAM. If a PJL password is declared and the wrong PASSWORD number is specified on the PJL JOB command, the printer will delay one half of a second before processing the next command.
PASSWORD = number

For detailed information on PJL password protection, see “File and Device Protection Commands” on page 3-93.
The EOJ command signifies the end of a print job.
@PJL EOJ [NAME = "job name"][]
Only use the EOJ command in conjunction with the JOB command.
NAME = "job name"
Use the NAME parameter to assign a character string name to a particular job. The name may be any combination of printable characters, spaces, or horizontal tabs up to a maximum of 80 characters, spaces, or tabs. The NAME string may be different from the NAME string specified in the JOB command. The job name must be enclosed in double quotes.

Environment Commands and Variables
This section describes the printer environment variables and the PJL commands used to modify or query the variables.
and the Hewlett-Packard Company’s LaserJet printers.
Beginning on Page ...
Common Variables for Both Printer Languages 3-12
Printer Unique Variables for Both Printer Languages 3-19
Common Variables for PCL emulation 3-48
Printer Unique Variables for PCL emulation 3-49
Common Variables for PostScript emulation 3-51
Printer Unique Variables for PostScript emulation 3-52
Printer Unique LRESOURCE Variables 3-53
The following commands modify the environment variables, and are described in this section:
The following commands query the environment variables, and are described in “Status Readback Commands” on page 3-54.
Categories

DEFAULT Command
This command modifies the default setting for the specified environment variable and stores the setting in the printer NVRAM. The new setting is activated with the occurrence of the next PJL reset condition.
The [command modifier:value] parameter specifies the type of PJL variables to be modified. The variables supported are listed in the tables beginning on page 3-12.
Values for "device:filename.filetype" are:
device flash, flash1, disk, or disk1 (case insensitive)
filename A unique identifier for a file, such as the macro ID for a PCL macro, the symbol set ID for a PCL symbol set, the font ID for a PCL font, and so on. The filename is case sensitive.
filetype An identifier that categorizes the file, such as p5macro for PCL macros or p5symset for PCL symbol sets. See “Table 3-22: Variables for Flash and Disk File and Password Commands” on page 3-87 for a complete list of the supported file types. The filetype is case sensitive.

The supported variables and values are listed in the tables beginning on page 3-12.
Read Only. Some variables may only be modified using the PJL SET command. These variables cannot be modified using the DEFAULT command. They are marked Set Only.
This command modifies the current setting for the specified environment variable. The new setting is active immediately, and remains active until the next occurrence of a PJL reset condition.
Use the SET command to modify any currently defined environment variable that cannot be set using the desired printer language. For example, use the PJL SET command to set Print Quality Enhancement Technology (PQET) or Page Protect, which cannot be set within a printer language such as PCL emulation.
The [command modifier:value] parameter specifies the type of PJL variables to be modified. The variables supported are listed in the tables beginning on page 3-12.
variable=value · where

Values for "device:filename.filetype" are:
device flash, flash1, disk, or disk1 (case insensitive)
filename A unique identifier for a file, such as the macro ID for a PCL macro, the symbol set ID for a PCL symbol set, the font ID for a PCL font, and so on. The filename is case sensitive.
filetype An identifier that categorizes the file, such as p5macro for PCL macros or p5symset for PCL symbol sets. See the table beginning on page 3-87 for a complete list of the supported file types. The filetype is case sensitive.
The supported variables and values are listed in the tables beginning on page 3-12.
Read Only. Some variables may only be modified using the PJL SET command. These variables cannot be modified using the DEFAULT command. They are marked Set Only.
variable=value

INITIALIZE Command
This command restores both the current and default environment variables to their factory default values and updates the printer NVRAM. This command affects all of the variables listed in “Table 3-3: Common Variables for Both Printer Languages” on page 3-12 through “Table 3-8: Printer Unique Variables for PostScript Emulation” on page 3-52, except the following:
“Table 3-9: Printer Unique LRESOURCE Variables” on page 3-53.
@PJL INITIALIZE[<CR>]<LF>
RESET Command
This command resets the current environment variables to the settings stored in the printer NVRAM. Therefore, any variables modified by the PJL SET command are returned to their default value after execution of the PJL RESET command.
@PJL RESET[<CR>]<LF>

and the Hewlett-Packard Company’s LaserJet printers.
The following common variables are supported for both PCL emulation and PostScript emulation, unless otherwise noted. Therefore, the [command modifier:value] parameter should not be specified.
To determine which variables your printer supports, see “Table B-1: Common Variables for Both Printer Languages” on page B-1.
Variable Function Selections Factory Default
Auto Continue 0, 5 to 255, OFF, ON
A value of 0 or OFF indicates Auto Continue is disabled. A value of ON indicates Auto Continue is set to 30.
INQUIRE or DINQUIRE on the Auto Continue variable returns a numeric value.
BINDING Duplex Bind LONGEDGE, SHORTEDGE LONGEDGE
BITSPERPIXEL Image Enhancement Technology and Image Enhancement Technology Type
1, 2, 4, Auto
A value of 1 indicates the Image Enhancement Technology setting is set to Off. A value of 2 or 4 indicates the Image Enhancement Technology setting is set to On.
INQUIRE or DINQUIRE returns the value of Image Enhancement Technology as follows:
Auto Continue from operator panel non-fatal warning messages
ON
If Auto Continue is set to On, JOB is returned.
If Auto Continue is set to Off, ON is returned.
COPIES Number of copies of each page
(DEFAULT only) · (READ only) · 1 to 999

Variable Function Selections Factory Default
Disables menus ON, OFF
ON disables the printer operator panel menus.
OFF enables menus.
DENSITY Print Darkness 1 to 5
2, 3, 4 (Model specific)
To determine the default value of your printer, see “Table B-1: Common Variables for Both Printer Languages” on page B-1.
DUPLEX Duplex ON, OFF OFF
ECONOMODE Toner Saver ON, OFF OFF
The value of the NVRAM serial number field is returned.
Set by printer manufacturer
The NVRAM serial number field is set to the printer serial number. In order to guarantee that a unique identifier exists in this field, the printer writes a random alphanumeric string into this field whenever the critical byte area in NVRAM is re-initialized.
FORMLINES Lines per page 1 to 255
60, 64 (Country specific)
Print and Hold ON, OFF, STORE, PROOF
The HOLD variable interacts with the HOLDKEY and HOLDTYPE variables. For more information, see HOLDTYPE on page 3-14.
Print and Hold PIN “PIN”
PIN is a text string consisting of exactly four numerals. Only the numerals 1 through 6 are valid.
The HOLDKEY variable interacts with the HOLD and HOLDTYPE variables. For more information, see HOLDTYPE as follows.

Variable Function Selections Factory Default
Print and Hold Type
PUBLIC
The HOLD, HOLDKEY, and HOLDTYPE variables interact with each other as follows:
ON, OFF ON
INTRAY2 Tray lock - Tray 2 UNLOCKED, LOCKED UNLOCKED
INTRAY3 Tray lock - Tray 3 UNLOCKED, LOCKED UNLOCKED
INTRAY4 Tray lock - Tray 4 UNLOCKED, LOCKED UNLOCKED
INTRAY5 Tray lock - Tray 5 UNLOCKED, LOCKED UNLOCKED
Tray 1 installed size, default formatting size
A3, A3+, A4, A5, B4, B4PAPER, B5PAPER, JISB4, JISB5, CUSTOM, EXECUTIVE, FOLIO, LEDGER, LEGAL, LETTER, 11X17, COM10, COM9, MONARCH, DL, C5, B5, OTHERENVELOPE, STATEMENT
LETTER, A4 (Country specific)
Tray 2 installed size, default formatting size
A3, A3+, A4, A5, B4, B4PAPER, B5PAPER, JISB4, JISB5, CUSTOM, EXECUTIVE, FOLIO, LEDGER, LEGAL, LETTER, 11X17, STATEMENT
LETTER, A4 (Country specific)
Tray 3 installed size, default formatting size
A3, A3+, A4, A5, B4, B4PAPER, B5PAPER, JISB4, JISB5, CUSTOM, EXECUTIVE, FOLIO, LEDGER, LEGAL, LETTER, 11X17, STATEMENT
LETTER, A4 (Country specific)
Tray 4 installed size, default formatting size
A3, A3+, A4, A5, B4, B4PAPER, B5PAPER, JISB4, JISB5, CUSTOM, EXECUTIVE, FOLIO, LEDGER, LEGAL, LETTER, 11X17, STATEMENT
LETTER, A4 (Country specific)
Tray 5 installed size, default formatting size
A3, A3+, A4, A5, B4, B4PAPER, B5PAPER, JISB4, JISB5, CUSTOM, EXECUTIVE, FOLIO, LEDGER, LEGAL, LETTER, 11X17, STATEMENT
LETTER, A4 (Country specific)
Print and Hold Jobname
jobname is a text string truncated to 24 characters.

Variable Function Selections Factory Default
JOBOFFSET Offset Pages ON, OFF, BETWEENJOBS, BETWEENCOPIES
INQUIRE or DINQUIRE returns the value of Offset Pages as follows:
Offset refers to stacking entire print jobs or copies of the same print job in two separate groups in an output bin.
DANISH, GERMAN, ENGLISH, SPANISH, FRENCH, ITALIAN, DUTCH, NORWEGIAN, SWEDISH, PORTUGUESE, FINNISH, JAPANESE, RUSSIAN, POLISH, HUNGARIAN, TURKISH, CZECH
Toner Alarm ON, OFF, CONTINUE, STOP
ON, CONTINUE (Model specific)
A value of ON or CONTINUE indicates the Toner Alarm setting is set Off. The value of OFF or STOP indicates the Toner Alarm setting is Single.
INQUIRE or DINQUIRE returns the value of the Toner Alarm as follows:
OFF
OFF
Printer always returns OFF.
MEDIATYPE Default paper source, default formatting size
PLAIN, COATED, GLOSSY, PHOTO, GREETINGCARD, IRONON, BOND, TRANSPARENCY, CARDSTOCK, LABELS, LETTERHEAD, PREPRINTED, COLORED, ENVELOPE, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE5, CUSTOMTYPE6, “name”
name is a variable that allows for custom naming of custom print material types. The text string is truncated to 24 characters.
CASSETTE, MANUAL, FIRST
CASSETTE
Sets the configuration of the Multipurpose Feeder.
ORIENTATION Print orientation PORTRAIT, LANDSCAPE
This variable does not affect PostScript emulation.

Variable Function Selections Factory Default
OUTBIN Output Bin UPPER, LOWER, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
A DINQUIRE or INQUIRE on the Output Bin setting returns:
DINQUIRE or Output Bin setting INQUIRE value
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
PAGEPROTECT Page Protect AUTO, ON
A value of ON indicates the Page Protect setting is set On. The value of AUTO indicates the Page Protect setting is set Off.
INQUIRE or DINQUIRE returns the value of the Page Protect as follows:
PAPER Default paper source, default formatting size
Paper: A3, A3+, A4, A5, B4, B4PAPER, B5PAPER, JISB4, JISB5, CUSTOM, EXECUTIVE, FOLIO, LEDGER, LEGAL, LETTER, STATEMENT, 11X17
LETTER, A4 (Country specific)

Variable Function Selections Factory Default
Parallel Protocol SLOW, FAST
A value of SLOW indicates the Parallel Protocol setting is Standard. The value of FAST indicates the Parallel Protocol setting is FASTBYTES.
INQUIRE or DINQUIRE returns the value of the Parallel Protocol as follows:
Default password for PJL NVRAM security
Locks the printer operator panel to keep the user defaults from changing. Refer to your printer user documentation for more information.
The Default PJL password is 0.
If the PJL password is not equal to 0, a DINQUIRE or INQUIRE on the PASSWORD variable returns ENABLED. If the PJL password is equal to 0, a DINQUIRE or INQUIRE on the PASSWORD variable returns DISABLED. See the PASSWORD parameter of the JOB command on page 3-5 for more information.
PCL, POSTSCRIPT, AUTO
AUTO
PERSONALITY controls the SmartSwitch settings for the interface link on which the PJL command is received.
If AUTO is sent, both PS SmartSwitch and PCL Smartswitch menu settings are set to ON.
If PCL is sent, PS SmartSwitch is set to OFF and PCL SmartSwitch is set to ON.
If POSTSCRIPT is sent, PCL SmartSwitch is set to OFF and PS SmartSwitch is set to ON.
When queried, AUTO is returned if both SmartSwitch settings are ON. If one SmartSwitch setting is OFF, the printer language whose SmartSwitch setting is ON is returned. If both SmartSwitch settings are OFF, the default printer language is returned.
ON, OFF
ON
ON enables the power-saving feature.
OFF disables the power-saving feature.

Variable Function Selections Factory Default
Power Save time, in minutes
0 to 120 (Model specific)
0 to 240 (Model specific)
(0 indicates the Power Saver Time feature is disabled.)
The time the printer remains idle before it enters Power Save mode when POWERSAVE is On.
Collation - Collated Copies (QTY)
Used to request the number of collated copies of a print job.
If Collation - Collated Copies (QTY) is not equal to 0, a DINQUIRE or INQUIRE returns the numerical setting for QTY. If Collation - Collated Copies (QTY) is set to Off, a DINQUIRE or INQUIRE returns 0.
REPRINT Jam Recovery ON, OFF, AUTO AUTO
RESOLUTION Print Resolution 300, 600, 1200 600
Resource Save ON, OFF, AUTO
OFF, AUTO (Model specific)
ON indicates Resource Save is set On.
OFF and AUTO indicate Resource Save is set to Off.
See “Table B-1: Common Variables for Both Printer Languages” on page B-1 for the default value of your printer.
RET Print Quality Enhancement Technology (PQET)
ON
If this value is set through PJL, the same value is returned on a PJL inquiry.
DARK, MEDIUM, LIGHT, and ON values indicate that PQET is On. OFF indicates PQET is Off.
TIMEOUT Print timeout, in seconds
The time the printer remains idle before the job is forced to print.

Variable Function Selections Factory Default
Print and Hold Username
username is a text string truncated to 24 characters.
WIDEA4 A4 width NO, YES
NO indicates the A4 width is 198 mm.
YES indicates the A4 width is 203 mm.
The following variables are unique to some Lexmark printers and are supported for both PCL emulation and PostScript emulation. Therefore, the [command
modifier:value] parameter should not be specified.
To determine which variables your printer supports, see “Table B-2: Printer Unique PJL Variables for Both Printer Languages” on page B-3.
Variable Function Selections Factory Default
MANUAL, AUTOMATIC MANUAL
LADVANCEDSTATUS
ON, OFF
ON
ON enables parallel bidirectional support.
OFF disables parallel bidirectional support.
Alarm Control OFF, SINGLE, CONTINUOUS SINGLE
LAUTOCRLF Auto CR after LF
LAUTOLFCR Auto LF after CR
LBLANKPAGES Blank Pages DONOTPRINT, PRINT
Bond Length NORMAL, SHORT NORMAL
OFF, DUPLEX OFF

Variable Function Selections Factory Default
Assign Type/Bin - Bond
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on bond paper.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Bond setting returns:
Assign Type/Bin - DINQUIRE or Bond setting INQUIRE value
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
Bond Texture SMOOTH, NORMAL, ROUGH ROUGH
Bond Weight LIGHT, NORMAL, HEAVY NORMAL
LBWLOCK Black & White Lock
LCANCEL Cancel Control ON, OFF ON
NORMAL, SHORT NORMAL
LCARDSTOCKLOADING
Card Stock Paper Loading

Variable Function Selections Factory Default
Assign Type/Bin - Card Stock
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on card stock.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Card Stock setting returns:
Assign Type/Bin - DINQUIRE or Card Stock setting INQUIRE value
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
SMOOTH, NORMAL, ROUGH NORMAL
LCARDSTOCKWEIGHT
LIGHT, NORMAL, HEAVY NORMAL
LCOLLATION Collation Mode ON, OFF
If Collation is ON, the pages of the print job are collated. For example, if the job contains three pages and two copies are requested, collated output prints pages 1, 2, 3, 1, 2, 3. If collation is set to OFF, uncollated output prints pages 1, 1, 2, 2, 3, 3.
LCOLORCORRECTION Indicates which color target the printer emulates
AUTO, VIVID (Model specific)
See “Table B-2: Printer Unique PJL Variables for Both Printer Languages” on page B-3 for the default value of your printer.
NORMAL, SHORT NORMAL

Variable Function Selections Factory Default
OFF, DUPLEX OFF
LCOLOREDOUTBIN
Assign Type/Bin - Colored Paper
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on colored paper.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Colored Paper setting returns:
Assign Type/Bin - DINQUIRE or Colored Paper INQUIRE value setting
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
SMOOTH, NORMAL, ROUGH NORMAL
LCOLOREDWEIGHT
LIGHT, NORMAL, HEAVY NORMAL
LCOLORMODEL Color Model CMYK, RGB, BLACK RGB, CMYK (Model specific)
LCUSTOMPAPERUNITS Universal Units of Measure
INCHES, MILLIMETERS INCHES, MILLIMETERS (Country specific)
LCUSTOMPAPERWIDTH Universal Width 76 to 915 in increments of 1 mm 3 to 36.01 in increments of 0.01 in.
216, 305 mm 8.5, 12 in. (Model and country specific)

Variable Function Selections Factory Default
76 to 915 in increments of 1 mm 3 to 36.01 in increments of 0.01 in.
356, 360, 457 mm 14, 14.17, 18 in. (Model and country specific)
LCUSTOMPAPERFEED Universal Feed Direction
LCUSTOMTYPE1LENGTH
Custom Type 1 Length
LCUSTOMTYPE1LOADING
Custom Type 1 Paper Loading
LCUSTOMTYPE1MEDIA
Custom Type 1 Media
PAPER
LCUSTOMTYPE1NAME
Custom Type 1 Name
name is a variable that allows for custom naming of print material types. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.

Variable Function Selections Factory Default
Assign Type/Bin - Custom Type 1
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on custom type 1 paper.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Custom Type 1 setting returns:
Assign Type/Bin - DINQUIRE or Custom Type 1 INQUIRE value setting
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
Custom Type 1 Texture
LCUSTOMTYPE1WEIGHT
Custom Type 1 Weight
LCUSTOMTYPE2LENGTH
Custom Type 2 Length
LCUSTOMTYPE2LOADING
Custom Type 2 Paper Loading
LCUSTOMTYPE2MEDIA
Custom Type 2 Media
PAPER

Variable Function Selections Factory Default
Custom Type 2 Name
name is a variable that allows for custom naming of print material types. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Assign Type/Bin - Custom Type 2
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on custom type 2 paper.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Custom Type 2 setting returns:
Assign Type/Bin DINQUIRE or Custom Type 2 INQUIRE value setting
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
Custom Type 2 Texture
LCUSTOMTYPE2WEIGHT
Custom Type 2 Weight
LCUSTOMTYPE3LENGTH
Custom Type 3 Length
LCUSTOMTYPE3LOADING
Custom Type 3 Paper Loading

Variable Function Selections Factory Default
Custom Type 3 Media
PAPER
LCUSTOMTYPE3NAME
Custom Type 3 Name
name is a variable that allows for custom naming of print material types. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Assign Type/Bin - Custom Type 3
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on custom type 3 paper.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Custom Type 3 setting returns:
Assign Type/Bin - DINQUIRE or Custom Type 3 INQUIRE value setting
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
Custom Type 3 Texture
LCUSTOMTYPE3WEIGHT
Custom Type 3 Weight
LCUSTOMTYPE4LENGTH
Custom Type 4 Length

Variable Function Selections Factory Default
Custom Type 4 Paper Loading
LCUSTOMTYPE4MEDIA
Custom Type 4 Media
PAPER
LCUSTOMTYPE4NAME
Custom Type 4 Name
name is a variable that allows for custom naming of print material types. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Assign Type/Bin - Custom Type 4
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on custom type 4 paper.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Custom Type 4 setting returns:
Assign Type/Bin DINQUIRE or Custom Type 4 INQUIRE value setting
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
Custom Type 4 Texture
LCUSTOMTYPE4WEIGHT
Custom Type 4 Weight

Variable Function Selections Factory Default
Custom Type 5 Length
LCUSTOMTYPE5LOADING
Custom Type 5 Paper Loading
LCUSTOMTYPE5MEDIA
Custom Type 5 Media
PAPER
LCUSTOMTYPE5NAME
Custom Type 5 Name
name is a variable that allows for custom naming of print material types. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Assign Type/Bin - Custom Type 5
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on custom type 5 paper.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Custom Type 5 setting returns:
Assign Type/Bin - DINQUIRE or Custom Type 5 INQUIRE value setting
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
Custom Type 5 Texture

Variable Function Selections Factory Default
Custom Type 5 Weight
LCUSTOMTYPE6LENGTH
Custom Type 6 Length
LCUSTOMTYPE6LOADING
Custom Type 6 Paper Loading
LCUSTOMTYPE6MEDIA
Custom Type 6 Media
PAPER
LCUSTOMTYPE6NAME
Custom Type 6 Name
name is a variable that allows for custom naming of print material types. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Assign Type/Bin - Custom Type 6
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on custom type 6 paper.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Custom Type 6 setting returns:
Assign Type/Bin - DINQUIRE or Custom Type 6 INQUIRE value setting
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”

Variable Function Selections Factory Default
Custom Type 6 Texture
LCUSTOMTYPE6WEIGHT
Custom Type 6 Weight
LDOWNLOADTARGET
RAM, FLASH, FLASH1, DISK, DISK1
RAM
If the device specified as the download target is write or read/write password protected, the download target will not be changed.
LDRYTIMEDELAY Dry Time Delay 0, 3 ... 30, OFF, AUTO OFF
LDUPLICATEHELDJOBS Delete or Save Print and Hold Jobs
LENVELOPEENHANCE
ON, OFF ON
LENVELOPELENGTH
NORMAL, SHORT NORMAL
LENVELOPEOUTBIN
Assign Type/Bin - Envelope
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on envelopes.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Envelope setting returns:
Assign Type/Bin - DINQUIRE or Envelope setting INQUIRE value
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”

Variable Function Selections Factory Default
SMOOTH, NORMAL, ROUGH NORMAL
LENVELOPEWEIGHT
LIGHT, NORMAL, HEAVY NORMAL
LESCCHAR
0 to 255 27
Fax Resolution STANDARD, FINE, SUPERFINE, ULTRAFINE
Fax Redial 0 to 14
PRINT, DONOTPRINT, PRINTERROR
PRINTERROR
LFEEDERPAPERTYPE Envelope Feeder Paper Type
ENVELOPE, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE5, CUSTOMTYPE6, “name”
name is a variable that allows for custom naming of print material types. The text string is truncated to 24 characters.
LGLOSSYLOADING Glossy Paper Loading

Variable Function Selections Factory Default
LGLOSSYOUTPUTBIN Assign Type/Bin - Glossy
UPPER, LOWER, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on Glossy paper.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Glossy setting returns:
Assign Type/Bin - DINQUIRE or Glossy setting INQUIRE value
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
LGLOSSYTEXTURE Glossy Paper Texture
LGLOSSYWEIGHT Glossy Paper Weight
LHOLEPUNCHALARM Hole Punch Alarm
LHOLEPUNCHMODE Hole Punch Mode
LHONORINIT
HONORSIGNAL, DONOTHONORSIGNAL DONOTHONOR SIGNAL
-100 to 100 0
LIMAGECONTRAST Image Contrast -100 to 100 0
LIMAGEENHANCE Image Enhancement Technology

Variable Function Selections Factory Default
LIMAGEENHANCETYPE Image Enhancement Technology Type
LIMAGEORIENTATION Page Image Orientation
DONOTROTATE
LIMAGESMOOTHING Image Smoothing for PostScript
LINFEEDERSIZE Envelope feeder installed size, default formatting size
COM10, DL (Country specific)
LINKALERT Ink Alert ON, OFF
Displays a printer attendance message when an ink cartridge is low.
LINMPFEEDERSIZE Multipurpose feeder installed size, default formatting size
Paper: A3, A3+, A4, A5, JISB4, B5PAPER, JISB5, CUSTOM, EXECUTIVE, FOLIO, LEDGER, LEGAL, LETTER, STATEMENT, 11X17
LETTER, A4 (Country specific)
LJAMRECOVERY Jam Recovery ON, OFF, AUTO AUTO
Labels Length NORMAL, SHORT NORMAL
OFF, DUPLEX OFF

Variable Function Selections Factory Default
Assign Type/Bin - Labels
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on labels.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Labels setting returns:
Assign Type/Bin - DINQUIRE or Labels setting INQUIRE value
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
Labels Texture SMOOTH, NORMAL, ROUGH NORMAL
Labels Weight LIGHT, NORMAL, HEAVY NORMAL
LLASTTRAYRENUMBER Last Tray Renumber
OFF
LLEFTMARGINOFFSET Left Margin Offset
-128 to 127 0
NORMAL, SHORT NORMAL
LLETTERHEADLOADING
OFF, DUPLEX OFF

Variable Function Selections Factory Default
Assign Type/Bin - Letterhead
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on letterhead paper.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Letterhead setting returns:
Assign Type/Bin - DINQUIRE or Letterhead setting INQUIRE value
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
SMOOTH, NORMAL, ROUGH NORMAL
LLETTERHEADWEIGHT
LIGHT, NORMAL, HEAVY NORMAL
LMANUALCOLORRGBTEXT Manual Color - RGB Text
LMANUALCOLORRGBGRAPHICS
Manual Color - RGB Graphics
LMANUALCOLORRGBIMAGE
Manual Color - RGB Image
LMANUALCOLORCMYKTEXT
Manual Color - CMYK Text
LMANUALCOLORCMYKGRAPHICS
Manual Color - CMYK Graphics

Variable Function Selections Factory Default
Manual Color - CMYK Image
LMANUALENVELOPESIZE Manual Envelope, default formatting size
COM10, DL (Country specific)
LMANUALENVELOPETYPE Manual Envelope Type
ENVELOPE, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE5, CUSTOMTYPE6, “name”
name is a variable that allows for custom naming of custom print material types. The text string is truncated to 24 characters.
LMANUALPAPERSIZE Manual Paper, default formatting size
A3, A3+, A4, A5, B4, B4PAPER, B5PAPER, CUSTOM, EXECUTIVE, FOLIO, JISB4, JISB5, LEDGER, LEGAL, LETTER, STATEMENT, 11X17
LETTER, A4 (Country specific)
LMANUALPAPERTYPE Manual Paper Type
PLAIN, COATED, GLOSSY, PHOTO, GREETINGCARD, IRONON, BOND, TRANSPARENCY, CARDSTOCK, LABELS, LETTERHEAD, PREPRINTED, COLORED, ENVELOPE, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE5, CUSTOMTYPE6, "name"
PLAIN, CUSTOMTYPE3 (Model specific)
name is a variable that allows for custom naming of print material types. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
LMPFEEDERPAPERTYPE Multipurpose Feeder Paper Type
PLAIN, COATED, GLOSSY, PHOTO, GREETINGCARD, IRONON, BOND, TRANSPARENCY, CARDSTOCK, LABELS, LETTERHEAD, PREPRINTED, COLORED, ENVELOPE, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE5, CUSTOMTYPE6, "name"
CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE6 PLAIN (Model specific)
name is a variable that allows for custom naming of print material types. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
HORIZONTAL, VERTICAL, REVHORIZONTAL, REVVERTICAL
HORIZONTAL
EUROCMYK (non-US) · LMULTIPAGEBORDER Multipage Border · LMULTIPAGEORDER Multipage Order

Variable Function Selections Factory Default
OFF, 2UP, 3UP, 4UP, 6UP, 9UP, 12UP, 16UP OFF
LMULTIPAGEVIEW Multipage View AUTO, SHORTEDGE, LONGEDGE AUTO
ON, OFF, AUTO
AUTO
This value is reported for the interface link that the command is received.
Optional Output Bin 1 Name
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Optional Output Bin 2 Name
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Optional Output Bin 3 Name
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Optional Output Bin 4 Name
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Optional Output Bin 5 Name
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.

Variable Function Selections Factory Default
Optional Output Bin 6 Name
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Optional Output Bin 7 Name
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Optional Output Bin 8 Name
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Optional Output Bin 9 Name
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Optional Output Bin 10 Name
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
MAILBOX, LINK, MAILBOXOVERFLOW, LINKOPTIONAL, TYPEASSIGNMENT
MAILBOX

Variable Function Selections Factory Default
Overflow Bin UPPER, LOWER, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
If an output bin is full, print jobs assigned to that output bin exit to the assigned overflow output bin.
A DINQUIRE or INQUIRE on the Overflow Bin setting returns:
Overflow Bin DINQUIRE or setting INQUIRE value
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
Overflow Timer, in minutes
A value of 0 (zero) indicates Overflow Timer is set to Disabled.
If Overflow Timer is set to Disabled, a DINQUIRE or INQUIRE on the Overflow Timer setting returns zero. If Overflow Timer is set to a numeric value, a DINQUIRE or INQUIRE on the Overflow Timer setting returns that value.
Page Count 0 to 999999 0
LPAGEMODE Print Area NORMAL, WHOLEPAGE, FULLPAGE NORMAL
LPAPERSOURCE Default paper source
TRAY1, TRAY2, TRAY3, TRAY4, TRAY5, FEEDER, MPFEEDER, MANUALPAPER, MANUALENVELOPE
TRAY1, TRAY2 (Model specific)
See “Table B-2: Printer Unique PJL Variables for Both Printer Languages” on page B-3 for the default value of your printer.

Variable Function Selections Factory Default
LPICTUREGRADE PictureGrade™ ON, OFF ON
NORMAL, SHORT NORMAL
LPLAINOUTBIN
Assign Type/Bin - Plain Paper
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on plain paper.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Plain setting returns:
Assign Type/Bin - DINQUIRE or Plain setting INQUIRE value
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
SMOOTH, NORMAL, ROUGH NORMAL
LPLAINWEIGHT
LIGHT, NORMAL, HEAVY NORMAL
LPOWERSAVER
Power Saver time, in minutes
0 to 120 (Model specific)
0 to 240 (Model specific)
(0 indicates the Power Saver feature is disabled.)
Some printer models released in the year 2000 or later designated as Energy Star printers cannot have Power Saver disabled.

Variable Function Selections Factory Default
Activate Personal Printer Data Stream (PPDS) printer language
OFF
Use ON to enable PPDS printer language and OFF to disable PPDS printer language. After this command is processed, the printer performs a Power On Reset (POR) to activate the changes.
Lines Per Page (PPDS)
1 to 255 64, 68 (Country specific)
Lines Per Inch 0.25 to 30.00 in increments of 0.25
NORMAL, SHORT NORMAL
LPREPRINTEDLOADING
OFF, DUPLEX OFF

Variable Function Selections Factory Default
LPREPRINTEDOUTBIN Assign Type/Bin - Preprinted Paper
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on preprinted paper.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Preprinted Paper setting returns:
Assign Type/Bin - DINQUIRE or Preprinted paper INQUIRE value setting
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
SMOOTH, NORMAL, ROUGH NORMAL
LPREPRINTEDWEIGHT
LIGHT, NORMAL, HEAVY NORMAL
LPRINTBUFFER Print Buffer control
ON
If ON is selected, Print Buffer displays with the Waiting message.
If OFF is selected, Print Buffer does not display with the Waiting message.
0 to 15 seconds 0
LPRINTERUSAGE Printer Usage MAXSPEED, MAXYIELD MAXSPEED, MAXYIELD (Model specific)
Disable Print Menus from front panel

Variable Function Selections Factory Default
LPRINTQUALITY Print Quality Mode
QUICKPRINT, NORMAL, PRESENTATION, GRAPHICS, IMAGES, 1200IMAGEQ, INKSAVER, NORMAL, BEST
LPUNCH Hole Punch ON, OFF OFF
LREAROUTBINNAME Rear Output Bin Name
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
Print and Hold Repeat Print Job Limit
0 to 50 jobs
Specifies the number of Repeat Print jobs that can be held in printer memory.
If the Repeat Print Job Limit setting is not equal to 0, a DINQUIRE or INQUIRE returns the numerical setting for LREPEATPRINTLIMIT. If Repeat Print Job Limit setting is set to Disabled, a DINQUIRE or INQUIRE returns 0.
LRESET Reset Control ON, OFF
When the LRESET variable is set to ON, RESET PRINTER is available in the JOB MENU when the printer is in the Busy or Waiting state. This is true for most printers with a printer operator panel.
If this variable is set to OFF, RESET PRINTER is not available.
Resource Save ON, OFF OFF
LRIGHTMARGINOFFSET Right Margin Offset
-10 to 10 0
LSCREENING Color Screening Selections
LSEPARATORSHEETS Indicates where separator sheets are placed within the print job
NONE
LSEPARATORSOURCE Indicates which source contains the separator sheets
TRAY1, TRAY2, TRAY3, TRAY4, TRAY5, FEEDER, MPFEEDER, MANUALPAPER, MANUALENVELOPE
"name" · (DEFAULT only) · (DEFAULT only)

Variable Function Selections Factory Default
Standard Output Bin Name
name is a variable that allows for custom naming of output bins. The text string is truncated to 24 characters.
When queried, the quotes are not returned around the string name. The default name is returned unless you have specified a custom name.
LSTROKEWIDTH PostScript minimum stroke width
1 pel or 1/600th inch
The width of a line or a stroke between two points.
LSTAPLE Staple Job ON, OFF, AUTO, FRONT, BACK, DUAL, 0, 1, 2 OFF
OFF, SINGLE, CONTINUOUS OFF
LSTAPLETESTBIN
OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10
OPTIONALOUT- BIN1, OPTIONAL OUTBIN2 (Model specific)
TRAY1, TRAY2, TRAY3, TRAY4, TRAY5, MPFEEDER TRAY1
LSUBSTITUTESIZE Substitute Size OFF, LETTERA4, STATEMENTA5, 11X17A3, ALLLISTED
OFF, LETTERA4, ALLLISTED (Model specific)
LTHINCOAT Thin Coat ON, OFF ON
Top Bin Timeout, in minutes
A DINQUIRE or INQUIRE on LTOPBINROTATE returns the numeric value.
LTOPMARGINOFFSET Top Margin Offset
-128 to 127 0
NORMAL, SHORT NORMAL

Variable Function Selections Factory Default
Assign Type/Bin - Transparency
UPPER, LOWER, DISABLED, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name”
UPPER, DISABLED (Model specific)
name is a variable that allows for custom naming of optional output bins. The text string is truncated to 24 characters.
Specifies a selected output bin for jobs printed on transparencies.
A DINQUIRE or INQUIRE on the Assign Type/Bin - Transparency setting returns:
Assign Type/Bin - DINQUIRE or Transparency setting INQUIRE value
Standard Bin UPPER Bin 1 OPTIONALOUTBIN1 Bin 2 OPTIONALOUTBIN2 Bin 3 OPTIONALOUTBIN3 Bin 4 OPTIONALOUTBIN4 Bin 5 OPTIONALOUTBIN5 Bin 6 OPTIONALOUTBIN6 Bin 7 OPTIONALOUTBIN7 Bin 8 OPTIONALOUTBIN8 Bin 9 OPTIONALOUTBIN9 Bin 10 OPTIONALOUTBIN10 “name” “name”
SMOOTH, NORMAL, ROUGH NORMAL
LTRANSPARENCYWEIGHT
LIGHT, NORMAL, HEAVY NORMAL
LTRAY1SENSEDTYPE PAPER
Detected Type for Paper - Tray 1
PLAIN, BOND, GLOSSY, CARDSTOCK, LABELS, LETTERHEAD, PREPRINTED, COLORED, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE6
LTRAY1SENSEDTYPE TRANSPARENCY
Detected Type for Transp- arency- Tray 1
LTRAY2SENSEDTYPE PAPER
Detected Type for Paper - Tray 2
PLAIN, BOND, GLOSSY, CARDSTOCK, LABELS, LETTERHEAD, PREPRINTED, COLORED, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE6
LTRAY2SENSEDTYPE TRANSPARENCY
Detected Type for Trans- parency - Tray 2

Variable Function Selections Factory Default
Detected Type for Paper - Tray 3
PLAIN, BOND, GLOSSY, CARDSTOCK, LABELS, LETTERHEAD, PREPRINTED, COLORED, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE6
LTRAY3SENSEDTYPE TRANSPARENCY
Detected Type for Trans- parency - Tray 3
LTRAY4SENSEDTYPE PAPER
Detected Type for Paper - Tray 4
PLAIN, BOND, GLOSSY, CARDSTOCK, LABELS, LETTERHEAD, PREPRINTED, COLORED, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE6
LTRAY4SENSEDTYPE TRANSPARENCY
Detected Type for Trans- parency - Tray 4
LTRAY1AUTOSIZE
Auto Size Sensing for Tray 1
LTRAY2AUTOSIZE
Auto Size Sensing for Tray 2
LTRAY3AUTOSIZE
Auto Size Sensing for Tray 3
LTRAY4AUTOSIZE
Auto Size Sensing for Tray 4
LTRAY5AUTOSIZE
Auto Size Sensing for Tray 5
LTRAY1PAPERTYPE Tray 1 Paper Type
PLAIN, COATED, GLOSSY, PHOTO, GREETINGCARD, IRONON, BOND, TRANSPARENCY, CARDSTOCK, LABELS, LETTERHEAD, PREPRINTED, COLORED, ENVELOPE, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE5, CUSTOMTYPE6, "name"
name is a text string that is truncated to 24 characters.

Variable Function Selections Factory Default
LTRAY2PAPERTYPE Tray 2 Paper Type
PLAIN, COATED, GLOSSY, PHOTO, GREETINGCARD, IRONON, BOND, TRANSPARENCY, CARDSTOCK, LABELS, LETTERHEAD, PREPRINTED, COLORED, ENVELOPE, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE5, CUSTOMTYPE6, "name"
PLAIN, CUSTOMTYPE2 (Model specific)
name is a text string that is truncated to 24 characters.
See “Table B-2: Printer Unique PJL Variables for Both Printer Languages” on page B-3 for the default value for your printer.
LTRAY3PAPERTYPE Tray 3 Paper Type
PLAIN, COATED, GLOSSY, PHOTO, GREETINGCARD, IRONON, BOND, TRANSPARENCY, CARDSTOCK, LABELS, LETTERHEAD, PREPRINTED, COLORED, ENVELOPE, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE5, CUSTOMTYPE6, "name"
PLAIN, CUSTOMTYPE3 (Model specific)
name is a text string that is truncated to 24 characters.
See “Table B-2: Printer Unique PJL Variables for Both Printer Languages” on page B-3 for the default value for your printer.
LTRAY4PAPERTYPE Tray 4 Paper Type
PLAIN, COATED, GLOSSY, PHOTO, GREETINGCARD, IRONON, BOND, TRANSPARENCY, CARDSTOCK, LABELS, LETTERHEAD, PREPRINTED, COLORED, ENVELOPE, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE5, CUSTOMTYPE6, "name"
PLAIN, CUSTOMTYPE4 (Model specific)
name is a text string that is truncated to 24 characters.
LTRAY5PAPERTYPE Tray 5 Paper Type
PLAIN, COATED, GLOSSY, PHOTO, GREETINGCARD, IRONON, BOND, TRANSPARENCY, CARDSTOCK, LABELS, LETTERHEAD, PREPRINTED, COLORED, ENVELOPE, CUSTOMTYPE1, CUSTOMTYPE2, CUSTOMTYPE3, CUSTOMTYPE4, CUSTOMTYPE5, CUSTOMTYPE6, "name"
PLAIN, CUSTOMTYPE5 (Model specific)
name is a text string that is truncated to 24 characters.
LTRAY1RENUMBER Tray 1 Renumber
LTYPE1FONTS Enables Type 1 fonts for PCL emulation
LUSDEFAULTS
US, NONUS US, NONUS (Country specific)
US/non-US defaults · (DEFAULT only)

and the Hewlett-Packard Company’s LaserJet printers.
Use these variables only for PCL emulation. The [command modifier:value] parameter should be specified as LPARM:PCL. For example:
To determine which variables your printer supports, see “Table B-3: Common Variables for PCL Emulation” on page B-11.
Variable Function Selections Factory Default
FONTNUMBER Font Number 0, 1, n 0
FONTSOURCE Font Source I, S, M1, M2, M3, M4, D1
I Internal font source S Permanent download fonts M1, M2, M3, M4 Flash font source D1 Disk font source
All other values default to internal font source.
PITCH Default pitch (fixed-pitch fonts)
0.08 to 100 (in increments of 0.01)
PTSIZE Default point size (proportional spaced fonts)
1 to 1008 (in increments of 0.25)
SYMSET Symbol set for the default font
For a list of the values for the Lexmark X422, see “Font and Symbol Set Support for the Lexmark X422” on page 2-9.
PC8, PC850 (Country specific)
For a list of the values for the Lexmark C510(n), see “Font and Symbol Set Support for the Lexmark C510(n)” on page 2-19.
If a symbol set is requested that is not resident in the printer, the symbol set is not changed.

The following variables are unique to your printer and are supported in PCL emulation only. The [command modifier:value] parameter should be specified as LPARM:PCL. For example:
To determine which variables your printer supports, see “Table B-4: Printer Unique Variables for PCL Emulation” on page B-11.
Variable Function Selections Factory Default
LA4WIDTH A4 Width in millimeters
LASSIGNFEEDER Tray Renumber Assign Envelope Feeder
OFF, 0 to 199
Variable used with PJL SET or DEFAULT command.
OFF, 0 to 199, NONE
Variable used with PJL INQUIRE or DINQUIRE command.
LASSIGNMANUALENVELOPE Tray Renumber Assign Manual Envelope
OFF, 0 to 199
Variable used with PJL SET or DEFAULT command.
OFF, 0 to 199, NONE
Variable used with PJL INQUIRE or DINQUIRE command.
LASSIGNMANUALPAPER Tray Renumber Assign Manual Paper
OFF, 0 to 199
Variable used with PJL SET or DEFAULT command.
OFF, 0 to 199, NONE
Variable used with PJL INQUIRE or DINQUIRE command.
LASSIGNMPFEEDER Tray Renumber Assign Multipurpose Feeder
OFF, 0 to 199
Variable used with PJL SET or DEFAULT command.
OFF, 0 to 199, NONE
Variable used with PJL INQUIRE or DINQUIRE command.
198, 203 198

Variable Function Selections Factory Default
LASSIGNTRAY1 Tray Renumber Assign Tray 1
OFF, 0 to 199
Variable used with PJL SET or DEFAULT command.
OFF, 0 to 199, NONE
Variable used with PJL INQUIRE or DINQUIRE command.
LASSIGNTRAY2 Tray Renumber Assign Tray 2
OFF, 0 to 199
Variable used with PJL SET or DEFAULT command.
OFF, 0 to 199, NONE
Variable used with PJL INQUIRE or DINQUIRE command.
LASSIGNTRAY3 Tray Renumber Assign Tray 3
OFF, 0 to 199
Variable used with PJL SET or DEFAULT command.
OFF, 0 to 199, NONE
Variable used with PJL INQUIRE or DINQUIRE command.
LASSIGNTRAY4 Tray Renumber Assign Tray 4
OFF, 0 to 199
Variable used with PJL SET or DEFAULT command.
OFF, 0 to 199, NONE
Variable used with PJL INQUIRE or DINQUIRE command.
LASSIGNTRAY5 Tray Renumber Assign Tray 5
OFF, 0 to 199
Variable used with PJL SET or DEFAULT command.
OFF, 0 to 199, NONE
Variable used with PJL INQUIRE or DINQUIRE command.
LBITMAPROUNDING Bitmap Font Partial Pel Rounding
ON
Some printers handle partial pel character escapement rounding of bitmap fonts differently. LBITMAPROUNDING offers a way of instructing the printer how to handle partial pel rounding of bitmap fonts.
Bitmap rounding is compatible with the Hewlett- Packard Company’s LaserJet printers.
LCOLOREXTENSIONS Color Extensions ON, OFF, HPCLJ5 ON

Variable Function Selections Factory Default
LFONTCOMPATIBILITY Font Compatibility Level
LFONTPRIORITY
Font Priority Search RESOLUTION, NORESOLUTION
When RESOLUTION is specified, your printer is compatible with the Hewlett-Packard Company’s LaserJet printers.
When NORESOLUTION is specified, font resolution is removed from the font selection priority criteria.
and the Hewlett-Packard Company’s LaserJet printers.
Use these variables only for PostScript emulation. The [command modifier:value] parameter should be specified as LPARM:POSTSCRIPT. For example:
To determine which variables your printer supports, see “Table B-5: Common Variables for PostScript Emulation” on page B-12.
JAMRECOVERY Jam Recovery ON, OFF
For queries, when the Jam Recovery setting is set to Auto, PJL returns the value of OFF. The remaining two Jam Recovery values, On and Off are returned by PJL as ON and OFF respectively.
When PJL is used to set Jam Recovery OFF, the setting is actually set to Auto. When PJL is used to set Jam Recovery ON, the setting is set to ON.
Changing this variable also affects PCL emulation.
PRTPSERRS Print PS Errors ON, OFF OFF
(SET only) · Factory Default · Variable Function Selections

The following variables are unique in some printers and are supported in PostScript emulation only.
To determine which variables your printer supports, see Table B-6 on page B-12.
Variable Function Selections Factory Default
LPICTUREGRADE PictureGrade ON, OFF ON
LPSFONTPRIORITY Font Priority RESIDENT, FLASHDISK RESIDENT
Use the following variables when additional storage devices are installed.
The [command modifier:value] parameter of the DEFAULT, INQUIRE, DINQUIRE, and SET commands must be specified as LRESOURCE:"device:filename.filetype". For example:
Values for "device:filename.filetype" are:
device flash, flash1, disk, or disk1 (case insensitive)
filename A unique identifier for a file, such as the macro ID for a PCL macro, the symbol set ID for a PCL symbol set, the font ID for a PCL font, or the actual file name for data, Type 1 fonts, and demo files as shown on the Directory. The filename is case sensitive.
filetype The identifier that categorizes the file, such as p5macro for PCL macros or p5symset for PCL symbol sets
Using the DEFAULT command to modify any of these variables forces a write to flash or disk if resource collection mode is set to On before the command is executed. The DEFAULT command causes a PJL Reset.

To determine which variables your printer supports, see “Table B-7: Printer Unique LRESOURCE Variables” on page B-13.
LDESCRIPTION
Macro or Symbol Set Description 1
The description is limited to 16 characters and must be enclosed in double quotes. If more than 16 characters are specified by the DEFAULT command, the first 16 characters are used and a PJL parser warning is issued.
The DINQUIRE command can be used to query the file description. The description is returned in the response.
Read/Write Lock (password) for an entire device or a particular file on the device 2
This variable can be used with other PJL commands:
The Read/Write password is limited to eight characters. If more than eight characters are specified by the PJL DEFAULT command, the password is truncated and a PJL warning is issued.
If a null (" ") password is given, password protection is removed from the specified device or file.
Use these commands to determine if a password has been specified for a device or specific file. The response is one of the following:
NOTSET The password has not been set or has been reset to zero. SET The password is defined and active. EXPIRED The password is reset to zero (flash memory only).
The LDECLARE command can be used to temporarily unlock access to a device or particular file. See “File and Device Protection Commands” on page 3-93 for additional information about using passwords on these devices.
Write Lock (password) for an entire device or particular file on the device 2
Same as LRWLOCK, except the password limits write-only access instead of read-write access.
1 The macro or symbol set description is printed in the Description field of the Print Directory listing. 2 To password protect a device, the command modifier:value should be LRESOURCE :"device:". The colon (:) and double quotes (" ") must be specified.

Status Readback Commands
Applications can request configuration and status information from the printer using the Status Readback commands. In addition, the printer can also be instructed to send unsolicited status information back to the host computer when asynchronous events occur, such as a memory error or a paper jam.
To determine which commands your printer supports, see “Table B-8: Status Readback Commands” on page B-13.
This command is used to query the default setting (NVRAM) of the specified environment variable.
where:
The [command modifier:value] parameter specifies the type of PJL variable to be queried. The variables supported are listed in the tables beginning on page 3-12.

Values for "device:filename.filetype" are:
device flash, flash1, disk, or disk1 (case insensitive)
filename A unique identifier for a file, such as the macro ID for a PCL macro, the symbol set ID for a PCL symbol set, the font ID for a PCL font, and so on. The filename is case sensitive.
filetype An identifier that categorizes the file, such as p5macro for PCL macros or p5symset for PCL symbol sets. See the table beginning on page 3-87 for a complete list of the supported file types. The filetype is case sensitive.
The supported variables are listed in the tables beginning on page 3-12.
This printer returns a ? for inquiries of an unsupported variable, or inquiries of a variable associated with an option that is not installed.
The ECHO command instructs the printer to return the specified words after the command is parsed. This command provides a method of capturing the status information returned by a specific print job.
@PJL ECHO [words][]
@PJL ECHO [words]
The words parameter must start with a printable character and can consist of a combination of printable characters, spaces, and horizontal tabs.
variable=value · words parameter

The INFO command is used to query status information from the printer. “Table 3-10: INFO Category Parameter Values” on page 3-56 lists the categories of information that can be queried.
See “Status Message Format” on page 3-61 for additional information about the messages returned by the INFO STATUS, USTATUS DEVICE, and USTATUS TIMED commands.
@PJL INFO category[]
@PJL INFO category [one or more lines of printable characters, spaces, or tabs]
Table 3-10 lists the supported categories.
ID Returns the model name or the model number stored in the printer NVRAM.
CONFIG Returns the printer configuration, including paper sources, paper sizes, and installed options.
MEMORY Returns the printer available memory.
PAGECOUNT Returns the printer page count.
STATUS Returns the printer current status.
VARIABLES Returns the printer environment variables and values.
USTATUS Returns the printer unsolicited status variables and values.
Category Values Description
![Page 164 of the Lexmark Printer user manual — PCL<CR><LF> USTATUS [4 ENUMERATED]<CR><LF>](/cdn/reader/75/7538781613ebc5cd24e1081047fb959492f200c822e50809a572d2415f265acb/images/page-164.webp?w=400)
@PJL INFO CONFIG<CR><LF>
IN TRAYS [2 ENUMERATED]<CR><LF>
INTRAY1<CR><LF> INTRAY2<CR><LF> MANUAL FEED<CR><LF> OUT TRAYS [1 ENUMERATED]<CR><LF>
UPPER FACEDOWN<CR><LF> PAPERS [13 ENUMERATED]<CR><LF>
LETTER LEGAL A4 A5 B5PAPER EXECUTIVE COM10 COM9 MONARCH DL C5 B5 OTHERENVELOPE LANGUAGES [1 ENUMERATED]
DEVICE JOB PAGE TIMED FLASH=1048576 DISK=543283200 MEMORY=2097152 DISPLAY LINES=2 SYSTEM FIRMWARE VERSION=250A ENGINE FIRMWARE VERSION=0

INQUIRE Command
This command is used to query the current setting of the specified environment variable.
The [command modifier:value] parameter specifies the type of PJL variables to be queried. The variables supported are listed in the tables beginning on page 3-12.
Values for "device:filename.filetype" are:
device flash, flash1, disk, or disk1 (case insensitive)
filename A unique identifier for a file, such as the macro ID for a PCL macro, the symbol set ID for a PCL symbol set, the font ID for a PCL font, and so on. The filename is case sensitive.
filetype An identifier that categorizes the file, such as p5macro for PCL macros or p5symset for PCL symbol sets. See the table beginning on page 3-87 for a complete list of the supported file types. The filetype is case sensitive.

The supported variables are listed in the tables beginning on page 3-12.
This printer returns a ? for inquiries of an unsupported variable, or inquiries of a variable associated with an option that is not installed.
This command is used to enable and disable unsolicited status from the printer. Unsolicited status information is sent automatically when an asynchronous event occurs. “Table 3-11: USTATUS Unsolicited Status Variable Values” on page 3-60 lists the asynchronous information that can be enabled and disabled.
@PJL USTATUS ustatus variable=value[]
@PJL USTATUS ustatus variable [one or more lines of printable characters, spaces, or tabs]
To determine which variables your printer supports, see “Table B-9: USTATUS Unsolicited Status Variables” on page B-13.
See “Status Message Format” on page 3-61 for additional information about the messages returned by the INFO STATUS, USTATUS DEVICE, and USTATUS TIMED commands.
variable=value

The following values are supported for the ustatus variable=value parameter.
Ustatus Variable Value Description
DEVICE ON Enables unsolicited status for device changes.
VERBOSE Enables unsolicited status for all device changes. Also enables warnings from the PJL parser.
OFF Disables unsolicited status for device changes.
JOB ON Enables unsolicited status for job changes. The printer sends a status message when a job begins and ends.
OFF Disables unsolicited status for job changes.
PAGE ON Enables unsolicited status for page changes. The printer sends a status message when a printed sheet reaches the standard output bin.
OFF Disables unsolicited status for page changes.
TIMED 5 to 300 in seconds Enables timed unsolicited status. The printer automatically sends status at a specified time interval.
0 Disables timed unsolicited status.
This command turns off unsolicited status. Unsolicited status may also be turned off by using the USTATUS command on each variable.
@PJL USTATUSOFF[<CR>]<LF>
ustatus variable=value

Status Message Format
The format of the returned information from the INFO STATUS, USTATUS DEVICE, and USTATUS TIMED commands is described in this section.
Information messages are returned in this form:
CODE=status code DISPLAY=display string (in double quotes) ONLINE=online status
Printer State Status Code Display String Online Status
Ready 10001 Ready TRUE
Ready 10001 RDYMSG TRUE
Ready with Ink Low 10006 88 Ink Low TRUE
Not Ready 10002 Not Ready FALSE
In the Menus 10002 Not Ready FALSE
Printer reset 10005 Resetting the Printer FALSE
Ready with Toner Low 10006 88 Toner Low TRUE
Ready with Toner Low 10006 88 Yellow Toner Low TRUE
Ready with Toner Low 10006 88 Magenta Toner Low TRUE
Ready with Toner Low 10006 88 Cyan Toner Low TRUE
Ready with Toner Low 10006 88 Black Toner Low TRUE
Ready with Toner Low 10006 88 Color Print Cartridge Low TRUE
Ready with Toner Low 10006 88 Black Print Cartridge Low TRUE
Ready with Toner Low 10006 88 Photo Print Cartridge Low TRUE
Ready with Replace Toner 10006 Replace Toner TRUE
Ready with Replace PC Kit 10006 Replace PC Kit TRUE
Ready with Replace Fuser 10006 Replace Fuser TRUE
x represents an input source code. For more information on input source codes, see “Table 3-16: Tray Codes” on page 3-74. yy represents a size code. For more information on size codes, see “Table 3-17: Media Size Codes” on page 3-74. ww represents the bin code. For more information on bin codes, see “Table 3-18: Output Bin Codes” on page 3-75. Note: The Display String is returned in the current language. A display message longer than one line shows only the first line
of the message.

Printer State Status Code Display String Online Status
Ready with Replace Transfer 10006 Replace Transfer TRUE
Power Saver with Ink Low 10006 88 Ink Low TRUE
Power Saver mode with Toner Low 10006 88 Toner Low TRUE
Power Saver mode with Replace Toner 10006 Replace Toner TRUE
Power Saver mode with Replace PC Kit 10006 Replace PC Kit TRUE
Power Saver mode with Replace Fuser 10006 Replace Fuser TRUE
Power Saver mode with Replace Transfer 10006 Replace Transfer TRUE
Cancelling Job 10007 Cancelling Job TRUE
Busy 10023 Busy TRUE
Waiting 10024 Waiting TRUE
Input Source Empty 11xyy Tray Empty TRUE
Input Source Missing 12xyy Tray Missing TRUE
Output Bin Full 15ww1 Bin Full TRUE
Resolution Reduced 35029 Res Reduced TRUE
Power Saver 35078 Powersaver TRUE
x represents an input source code. For more information on input source codes, see “Table 3-16: Tray Codes” on page 3-74. yy represents a size code. For more information on size codes, see “Table 3-17: Media Size Codes” on page 3-74. ww represents the bin code. For more information on bin codes, see “Table 3-18: Output Bin Codes” on page 3-75. Note: The Display String is returned in the current language. A display message longer than one line shows only the first line
of the message.

Auto-Continuable Conditions
These status messages are returned independent of the state of the Auto Continue menu item. Auto-continuable messages are returned in this form:
CODE=status code DISPLAY=display string (in double quotes) ONLINE=online status
To determine which messages your printer supports, see “Table B-10: PJL Messages for Auto-Continuable Conditions” on page B-14.
Status Code Display String Online Status
30014 50 PPDS Font Error FALSE
30016 37 Insufficient Collation Area FALSE
30016 37 Insufficient Defrag Memory FALSE
30016 37 Insufficient Memory FALSE
30016 38 Memory Full FALSE
30016 Held Jobs May Not Be Restored FALSE
30016 57 Configuration Change FALSE
30017 39 Complex Page FALSE
30018 54 Standard Serial Error FALSE
30018 54 Parallel Error FALSE
30018 54 Std Network Software Error FALSE
30018 54 Std Ser Fax Connection Lost FALSE
30018 56 Standard Serial Disabled FALSE
the message.
Printer State

Status Code Display String Online Status
30018 56 Serial 1 Port Disabled FALSE
30018 56 Standard Parallel Port Disabled FALSE
30018 56 Parallel Port Disabled FALSE
30018 56 Parallel Port x Disabled FALSE
30018 56 Standard USB Port Disabled FALSE
30019 35 Res Save Off Deficient Memory FALSE
30026 55 Insufficient Fax Buffer FALSE
30027 54 Std Par ENA Connection Lost FALSE
30027 56 Std Parallel Port Disabled FALSE
30031 Print Jobs on Disk? or Print Jobs on Disk. Go/Stop?
30031 Restore Held Jobs. Go/Stop? FALSE
30034 34 Short Paper FALSE
30035 52 Flash Full FALSE
30035 62 Disk Full FALSE
30036 51 Defective Flash FALSE
30036 53 Unformatted Flash FALSE
30036 61 Defective Disk FALSE
30036 63 Unformatted Disk FALSE
the message.
Printer State

Status Code Display String Online Status
30075 80 Scheduled Maintenance FALSE
30076 35 Res Save Off Deficient Memory FALSE
30076 37 Insufficient Collation Area FALSE
30107 Empty Hole Punch Box FALSE
30107 Empty Box M FALSE
30107 Insert Box M FALSE
30107 Insert Staple Cartridge FALSE
30107 Insert Stapler FALSE
30107 Priming Failed, Retry. Go/Stop? FALSE
30112 54 Network x Software Error FALSE
30112 56 Serial Port x Disabled FALSE
30112 54 Serial Option x Error FALSE
30112 54 Ser x Fax Connection Lost FALSE
30112 56 USB Port x Disabled FALSE
30113 54 Par x ENA Connection Lost FALSE
30113 56 Parallel Port x Disabled FALSE
32001 Operation Failed Jobs on Disk FALSE
32001 Operation Failed Faxes on Disk FALSE
32002 52 Flash Full FALSE
the message.
Printer State

Status Code Display String Online Status
32002 62 Disk Full FALSE
32015 Disk Corrupted. Reformat? FALSE
32030 58 Too Many Flash Options FALSE
32052 53 Unformatted Flash FALSE
32052 63 Unformatted Disk FALSE
32052 64 Unsupported Disk Format FALSE
32056 51 Defective Flash FALSE
32056 61 Defective Disk FALSE
35075 80 Scheduled Maintenance FALSE
35075 81 Scheduled Maintenance FALSE
40038 80 Fuser/Belt Life Warning FALSE
40038 80 Fuser/Belt Exhausted FALSE
the message.
Printer State

Attendance Conditions
Attendance conditions require operator intervention. Attendance messages are returned in this form:
CODE=status code DISPLAY=display string (in double quotes) ONLINE=online status
To determine which messages your printer supports, see “Table B-11: PJL Messages for Attendance Conditions” on page B-18.
Printer State Status Code Display String Online Status
40010 30 Coating Roll Missing FALSE
40010 30 XXXX1 Print Unit Missing FALSE
40010 Insert Hole Punch Box FALSE
40010 Insert PC Cartridge FALSE
40021 Cover Open or Close Top Covers or Insert Cartridge or Close Door
40021 Close Cover A FALSE
40021 31 Defective Print Cartridge 31 Defective Cartridge XXXX FALSE
40021 32 Unsupported Print Cartridge FALSE
40021 32 Unsupported XXXX Cartridge FALSE
40021 32 Unsupported Cartridge FALSE
40021 Change Cartridge Invalid Refill FALSE
40021 Cartridge Life Expired XXXX FALSE
1 XXXX represents a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow and Black cartridges, respectively. For this message, the values for XXXX are returned to indicate which ink cartridges are defective. 2 represents a one-letter designator for each door labeled on the printer. 3 represents a one-letter designator for each cover labeled on the printer. Note: The Display String is returned in the current language. A display string that is returned is truncated to the DISPLAY
CHARACTER SIZE returned in INFO CONFIG.

Printer State Status Code Display String Online Status
40021 Cartridge Life Warning XXXX FALSE
40021 31 Missing Cartridge XXXX FALSE
40021 31 Missing Printhead FALSE
40021 32 Unsupported Printhead FALSE
40021 40 Tray x Size Sense Error FALSE
40021 41 Open Bin 1 Exit Tray FALSE
40021 Close Cover FALSE
40021 Open Cover FALSE
40021 Close Deflector G FALSE
40021 Open Rear Door FALSE
40021 Close Front Door FALSE
40021 Close Side Door FALSE
40021 Close Finisher Door FALSE
40021 Close Finisher Side Door FALSE
40021 Close Finisher Top Cover FALSE
40021 Close Door <d> FALSE
40021 Close Cover <c> FALSE
40021 Close Tray x Top Cover FALSE
1 XXXX represents a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow and Black cartridges, respectively. For this message, the values for XXXX are returned to indicate which ink cartridges are defective. 2 represents a one-letter designator for each door labeled on the printer. 3 represents a one-letter designator for each cover labeled on the printer. Note: The Display String is returned in the current language. A display string that is returned is truncated to the DISPLAY
CHARACTER SIZE returned in INFO CONFIG.

Printer State Status Code Display String Online Status
40021 Insert Print Cartridge FALSE
40022 2xx Paper Jam FALSE
40027 Check Tray <source #> Connection FALSE
40027 Install Tray x or Cancel Job FALSE
40028 Reattach Envelope Feeder FALSE
40028 Reattach MP Feeder FALSE
40028 Install Env Feed or Cancel Job FALSE
40029 Reattach Output Bin <bin #> FALSE
40029 Reattach Bins <bin #x - bin #y> FALSE
40029 Install Bin x or Cancel Job FALSE
40029 Check Finisher Installation FALSE
40029 Check Mailbox Installation FALSE
40030 33 Tray x Config Error FALSE
40030 58 Input Config Error FALSE
40030 58 Too Many Trays Attached FALSE
40030 58 Too Many Bins Attached FALSE
40030 58 Too Many Disks Installed FALSE
40036 58 Too Many Disks Installed FALSE
1 XXXX represents a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow and Black cartridges, respectively. For this message, the values for XXXX are returned to indicate which ink cartridges are defective. 2 represents a one-letter designator for each door labeled on the printer. 3 represents a one-letter designator for each cover labeled on the printer. Note: The Display String is returned in the current language. A display string that is returned is truncated to the DISPLAY
CHARACTER SIZE returned in INFO CONFIG.

Printer State Status Code Display String Online Status
40037 31 PerfectFinish Missing FALSE
40037 87 PerfectFinish Empty FALSE
40038 84 Black Photo Dev Life Warning FALSE
40038 84 Color Photo Dev Life Warning FALSE
40038 84 All Photo Devs Exhausted FALSE
40038 84 Black Photo Dev Exhausted FALSE
40038 88 Toner Low FALSE
40038 88 Yellow Toner Low FALSE
40038 88 Magenta Toner Low FALSE
40038 88 Cyan Toner Low FALSE
40038 88 Black Toner Low FALSE
40038 88 Yellow Toner Empty FALSE
40038 88 Cyan Toner Empty FALSE
40038 88 Magenta Toner Empty FALSE
40038 88 Black Toner Empty FALSE
40038 88 Color Print Cartridge Low FALSE
40038 88 Black Print Cartridge Low FALSE
40038 88 Photo Print Cartridge Low FALSE
1 XXXX represents a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow and Black cartridges, respectively. For this message, the values for XXXX are returned to indicate which ink cartridges are defective. 2 represents a one-letter designator for each door labeled on the printer. 3 represents a one-letter designator for each cover labeled on the printer. Note: The Display String is returned in the current language. A display string that is returned is truncated to the DISPLAY
CHARACTER SIZE returned in INFO CONFIG.

Printer State Status Code Display String Online Status
40038 88 Cartridge Low <CMYK>
40038 Replace PC Kit FALSE
40038 Replace PC Kit To Continue FALSE
40038 Replace Toner Cartridge FALSE
40038 Replace Toner To Continue FALSE
40038 Replace Oil Coating Roll FALSE
40039 89 Cartridge Empty <CMYK>
40040 Load Staples FALSE
Intervention required: priming failed. retry?
40041 Priming Failed. Retry? FALSE
40048 Message specified by OPMSG FALSE
40049 Message specified by STMSG FALSE
40050 Replace Fuser FALSE
40050 Replace Transfer Kit FALSE
40087 59 Incompatible Bin x FALSE
40088 59 Incompatible Duplex FALSE
40089 59 Incompatible Tray x FALSE
40090 59 Incompatible Envelope Feeder FALSE
40095 Check Duplex Connection FALSE
1 XXXX represents a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow and Black cartridges, respectively. For this message, the values for XXXX are returned to indicate which ink cartridges are defective. 2 represents a one-letter designator for each door labeled on the printer. 3 represents a one-letter designator for each cover labeled on the printer. Note: The Display String is returned in the current language. A display string that is returned is truncated to the DISPLAY
CHARACTER SIZE returned in INFO CONFIG.

Printer State Status Code Display String Online Status
40095 Install Duplex or Cancel Job FALSE
40096 Close Duplex Door FALSE
40096 Insert Duplex Option FALSE
40101 Load Staples FALSE
1 XXXX represents a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow and Black cartridges, respectively. For this message, the values for XXXX are returned to indicate which ink cartridges are defective. 2 represents a one-letter designator for each door labeled on the printer. 3 represents a one-letter designator for each cover labeled on the printer. Note: The Display String is returned in the current language. A display string that is returned is truncated to the DISPLAY
CHARACTER SIZE returned in INFO CONFIG.
When a Load <tray>, Load Manual, or Change <tray> message appears on the printer operator panel display or through MarkVision Professional, a message is returned to the host computer indicating the paper source and size for the prompt.
Attendance (operator intervention) messages are returned in this form:
CODE=status code DISPLAY=display string (in double quotes) ONLINE=online status
The display string is the first line of the message that displays.

To determine which messages your printer supports, see “Table B-12: PJL Messages for Paper Handling” on page B-23.
Status Code Display String* Online Status
30034 34 Wrong Paper Size in Tray x FALSE
30034 34 Wrong Paper Size Manual Feed FALSE
40019 Remove Paper Standard Bin FALSE
40019 Remove Paper Output Bin <bin #> FALSE
40019 Remove Paper All Output Bins FALSE
40019 Remove Paper <linked set bin name> FALSE
4100x Check <source> Paper Guide FALSE
41xyy 34 Incorrect Media FALSE
41xyy Load <source>... <Custom Type Name> <Custom String> <size> <type> <size>
41xyy Load Manual <Custom Type Name> <Custom String> <size> <type> <size>
41xyy Change <source>... <Custom Type Name> <Custom String> <size> <type> <size>
Intevention required: insert duplex pages & press Go.
412yy Insert Duplex Pages & Press Go. FALSE
4300x Insert Tray <source #> FALSE
x represents an input source code. For more information, see “Table 3-16: Tray Codes” on page 3-74. yy represents a media size code. For more information, see “Table 3-17: Media Size Codes” on page 3-74. * Refer to your printer user documentation for more information on printer messages.
Printer State

Table 3-17: Media Size Codes
YY Value Media Size
06 11 x 17 (Ledger)
08 Com 10 Envelope
09 7 3/4 Envelope (Monarch)
13 JIS B5 Paper
16 A3+, JB4 Paper (Model specific)

YY Value Media Size
90 Com 9 Envelope
WW Value Output Bin
When a <#> Paper Jam message appears on the printer operator panel display or through MarkVision Professional, a message is returned to the host computer indicating the type and location for the prompt.
Attendance (operator intervention) messages are returned in this form:
CODE=status code DISPLAY=display string (in double quotes) ONLINE=online status

To determine which messages your printer supports, see Table B-13 on page B-24.
Printer State Status Code Display String* Online Status
4200x 200 Paper Jam FALSE
4201x 201 Paper Jam FALSE
4202x 202 Paper Jam FALSE
4203x 203 Paper Jam FALSE
4204x 204 Paper Jam FALSE
4205x 205 Paper Jam FALSE
4206x 206 Paper Jam FALSE
4207x 207 Paper Jam FALSE
4208x 208 Paper Jam FALSE
4209x 209 Paper Jam FALSE
4210x 210 Paper Jam FALSE
4211x 211 Paper Jam FALSE
4220x 220 Paper Jam FALSE
4221x 221 Paper Jam FALSE
4222x 222 Paper Jam FALSE
4230x 230 Paper Jam FALSE
4231x 231 Paper Jam FALSE
w indicates this message includes a letter indicating a door or cover. The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number. * Refer to your printer user documentation for more information on printer messages.

Printer State Status Code Display String* Online Status
4232x 232 Paper Jam FALSE
4233x 233 Paper Jam FALSE
4234x 234 Paper Jam FALSE
424yx 24y Paper Jam FALSE
4241wy 241 Paper Jam FALSE
4242wy 242 Paper Jam FALSE
4243w 243 Paper Jam FALSE
4244wy 244 Paper Jam FALSE
4245w 245 Paper Jam FALSE
4246w 246 Paper Jam FALSE
4247wy 247 Paper Jam FALSE
4248w 248 Paper Jam FALSE
4249w 249 Paper Jam FALSE
4250w 250 Paper Jam FALSE
4250x 250 Paper Jam FALSE
4251wy 251 Paper Jam FALSE
4251x 251 Paper Jam FALSE
4252w 252 Paper Jam FALSE
w indicates this message includes a letter indicating a door or cover. The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number. * Refer to your printer user documentation for more information on printer messages.

Printer State Status Code Display String* Online Status
4253w 253 Paper Jam FALSE
4254wy 254 Paper Jam FALSE
4255 255 Paper Jam FALSE
4256w 256 Paper Jam FALSE
4257w 257 Paper Jam FALSE
4258w 258 Paper Jam FALSE
4259wy 259 Paper Jam FALSE
4260w 260 Paper Jam FALSE
4260x 260 Paper Jam FALSE
4261w 261 Paper Jam FALSE
4261x 261 Paper Jam FALSE
427zx 27z Paper Jam FALSE
4271 271 Paper Jam FALSE
4272 272 Paper Jam FALSE
4273 273 Paper Jam FALSE
4280x 280 Paper Jam FALSE
4280x Clear Staple Job from Finisher FALSE
4280w 280 Paper Jam FALSE
w indicates this message includes a letter indicating a door or cover. The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number. * Refer to your printer user documentation for more information on printer messages.

Printer State Status Code Display String* Online Status
4281w 281 Paper Jam FALSE
4281x 281 Paper Jam FALSE
4282w 282 Paper Jam FALSE
4282x 282 Paper Jam FALSE
4283w 283 Paper Jam FALSE
4283x 283 Paper Jam FALSE
4284w 284 Paper Jam FALSE
4284x 284 Paper Jam FALSE
4285w 285 Paper Jam FALSE
4286w 286 Paper Jam FALSE
4287 287 Paper Jam FALSE
4288 288 Paper Jam FALSE
4289 289 Paper Jam FALSE
4290 290 Paper Jam FALSE
4291 291 Paper Jam FALSE
4292 292 Paper Jam FALSE
4293 293 Paper Jam FALSE
w indicates this message includes a letter indicating a door or cover. The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number. * Refer to your printer user documentation for more information on printer messages.

Printer State Status Code Display String* Online Status
4294 294 Paper Jam FALSE
4295 295 Paper Jam FALSE
w indicates this message includes a letter indicating a door or cover. The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number. * Refer to your printer user documentation for more information on printer messages.
Error Code 50000 is returned for all 9xx Service Errors when the printer can return a status code.
To determine whether your printer supports returning service messages, see “Table B-14: Service Errors” on page B-29.
To determine which commands your printer supports, see “Table B-15: Device Attendance Messages” on page B-29.
The RDYMSG command is used to specify a message that appears on the first line of the printer operator panel display or through MarkVision Professional whenever the printer is ONLINE (in the Ready or Busy state). This message displays instead of the
Ready or Busy message.

@PJL RDYMSG DISPLAY = "message"[]
When an OPMSG command is received, the message appears and is allotted both lines of the display. The printer is taken OFFLINE. This message, along with the STMSG command, is the lowest priority, so if another intervention occurs, it displays instead.
your printer to the ONLINE state. Once in the ONLINE state, the Ready, Busy, or Waiting message appears on the printer operator panel display or through MarkVision Professional.
A printer reset is not available from the printer operator panel or through MarkVision Professional while OPMSG displays.
@PJL OPMSG DISPLAY = "message"[]
When a STMSG command is received, the message appears and is allotted both lines of the display. The printer is taken OFFLINE. This message, along with the OPMSG command, is the lowest priority, so if another intervention occurs, it displays instead.
your printer to the ONLINE state. Once in the ONLINE state, the Ready, Busy, or Waiting message appears on the printer operator panel display or through MarkVision Professional.
A printer reset is not available from the printer operator panel or through MarkVision Professional while STMSG displays.
@PJL STMSG DISPLAY = "message"[]

Unique PJL Commands
To determine which commands your printer supports, see “Table B-16: Lexmark Unique PJL Commands” on page B-29.
This command causes the printer to beep three times.
@PJL LBEEP[<CR>]<LF>
LPORTROTATE Command
This command causes the printer to rotate ports at the next job boundary. The information to rotate ports is specified in the job header. For example, the printer could switch from parallel interface to serial interface between jobs.
@PJL LPORTROTATE[<CR>]<LF>

LPRINT Commands (Information Pages)
Use these commands to print one of the internal information pages.
The supported testpage values are listed in the following table.
LPRINTDIRECTORY Prints both the flash and disk directory listings. If neither flash memory or a disk is installed, the command is ignored.
LPRINTTESTPAGE Prints the test page.
LPRINTMENUS Prints the menu settings page.
LPRINTPCLFONTS Prints the PCL font listing.
LPRINTPSFONTS Prints the PostScript font listing.
For example, to print a menu settings page:
@PJL LPRINTMENUS[<CR>]<LF>
LESCAPECHAR Command
This command modifies the code point of the escape character for the host computer specified by the PORT parameter. The escape character is mapped to code point 0x1B for each host interface port.
@PJL LESCAPECHAR CHAR=byte PORT=port []
The byte value for the CHAR parameter is the code point of the ASCII character used for the escape character.
For example, at the factory, the printer uses 0x1B (character ) for the escape character. If CHAR = 65 is specified with this command, the printer uses 0x41 (character ‘A’) as the escape character for the host interface port specified via the PORT parameter.
@PJL testpage[] · testpage Value Description · CHAR parameter

The following ports are valid parameters for LESCAPECHAR:
PORT parameter

LFAX PHONENUMBER Command
This command tells the printer that the output resulting from the current job is being sent to the fax processing device instead of to the printer. The current job is printed and is not sent to the fax processing device if one of the following occurs:
@PJL LFAX PHONENUMBER=“number” [STATIONID=“station name”][]
The PHONENUMBER parameter is a text string up to 60 characters long. If an unsupported character is supplied in the PHONENUMBER parameter, the entire LFAX PHONENUMBER command is ignored.
* DTMF1 character *
# DTMF1 character #
A - D DTMF1 characters A, B, C, and D
W Wait for dial tone
@ Wait for silence
& Wait for credit card tone
^ Toggles between tone and pulse modes
1 DTMF, Dual Tone Multi-Frequency, is the system used by touch-tone telephones which assigns a specific frequency, or tone, to each key so it can easily be identified by a microprocessor.
[STATIONID=“station name”]
The STATIONID parameter specifies a station name that is sent to the receiving fax machine to indicate the origin of an incoming fax. The “station name” is a text string which is truncated to 20 characters. A null value (“ “) indicates no station ID is specified. If no station name is specified, the default station name of the printer is used.

LDOWNLOADTARGET Command
This command specifies which device is the target for downloaded files. The target can be RAM, flash, or disk.
@PJL SET LDOWNLOADTARGET=variable []
Use the following commands to manage resources on flash and disk devices:
@PJL LOPENFILE DEVICE=filedevice FILENAME=fname ACCESS=accesstype []
See Chapter 6: “Flash Memory and Disk” for more information.

Table 3-22 lists the parameters used with most of the commands. Additional parameters are noted in the description of each command.
accesstype ACCESS = accesstype One of the following access types must be specified when a file is opened:
RO Open for read only. File must already exist on specified device. WO Create a new file. If the file already exists, its contents will be
discarded and a new file will be created. RW Open for reading and writing. File must already exist. AP Open for reading and writing, and position the file pointer to the end
of the file. File must already exist.
Access types are case sensitive.
The LREADFILE command is ignored if the file was not opened with an accesstype of RO, RW, or AP. The LWRITEFILE command is ignored if the file was not opened with an accesstype of WO, RW, or AP.
bytecount LENGTH = bytecount The amount of data in bytes to be read or written. The parameter is optional for both the LREADFILE and LWRITEFILE commands.
If the LENGTH parameter is omitted from the LREADFILE command, bytecount is assumed to be equal to the entire file beginning at the START location. If the LENGTH parameter is omitted from the LWRITEFILE command, an @PJL END DATA command must be placed at the end of the data. All data up to ‘@’ in @PJL END DATA is written to the file.
If the LENGTH is greater than the file size on a LREADFILE command, it is assumed to be the entire file beginning at the START location.
Parameter Syntax Description

filedevice DEVICE = filedevice File storage media. Case insensitive.
The rom value is used for the LRUNFILE command only.
flashdevice DEVICE = flashdevice File storage media.
filename FILENAME = "fname" OLDFILENAME = "fname" NEWFILENAME = "fname"
Fname is comprised of a filename, a unique identifier for a file, and a filetype, which specifies the type of file. The format is filename.filetype.
The filename must be one of the following:
macro ID PCL macros symbol set ID PCL symbol sets font ID PCL fonts actual filename data, Type 1 fonts, demo files (case sensitive)
The filetype must be one of the following:
t1 PostScript font sFnt5 PCL scalable font bFnt5 PCL bitmap font MAC5 PCL macro data User Data type1 PostScript font demo Demo p5scalable PCL scalable font p5bitmap PCL bitmap font p5macro PCL macro p5symset PCL symbol set ppdsbm PPDS bitmap font xlmacro PCL XL user stream
All fname specifications must be enclosed in quotation marks and cannot exceed 127 characters.
If the file is password-protected, the password must be provided in order to unlock the file.
For additional information about passwords, see “File and Device Protection Commands” on page 3-93.
Parameter Syntax Description

location START = location The location in the file to begin writing or reading. Use an integer that represents an offset in bytes from the beginning of the file.
Optional for both LREADFILE and LWRITEFILE commands. If omitted on an LREADFILE command, location of 0 (beginning of the file) is assumed. If omitted on an LWRITEFILE command with an accesstype of RW, location of 0 is also assumed.
If a START location is provided but it is greater than the file size, the LREADFILE command response will contain no file data. Similarly, an LWRITEFILE command with an accesstype of RW functions like an LWRITEFILE command with an accesstype of AP.
automatically attach a .data extension to the fname. See “Filename Extensions” on page 6-10 for more information. For example, if "myfile" is downloaded to flash through PostScript emulation, the fname on the PJL commands is "myfile.data".
Use this command to open a file on a storage device.
@PJL LOPENFILE DEVICE = filedevice FILENAME = "fname" ACCESS = accesstype[]
Use this command to close a file on a storage device. The command is ignored if the file doesn’t exist on the device or if the file is not open.
@PJL LCLOSEFILE DEVICE = filedevice FILENAME = "fname"[]
Parameter Syntax Description

LREADFILE Command
Use this command to read data from a file on a storage device.
@PJL LREADFILE DEVICE = filedevice FILENAME = "fname" [START = location] [LENGTH = bytecount][]
@PJL LREADFILE DEVICE = filedevice FILENAME = "fname" START = location LENGTH = bytecount @PJL END DATA

LWRITEFILE Command
Use this command to write data to a file on a storage device.
@PJL LWRITEFILE DEVICE = filedevice FILENAME = "fname" [START = location] [LENGTH = bytecount][] [@PJL END DATA][]
Use this command to load and execute a file on a storage device. For example, use this command to run the resident demo file or a demo file stored on flash or disk.
@PJL LRUNFILE DEVICE = filedevice FILENAME = "fname"[]

LRENAMEFILE Command
Use this command to rename a file on a storage device. The command is ignored if the filename specified as OLDFILENAME doesn’t exist on the device, or if the filename specified as NEWFILENAME already exists on the device.
@PJL LRENAMEFILE DEVICE = filedevice OLDFILENAME = "fname" NEWFILENAME = "fname"[]
Use this command to delete a file on a storage device. The command is ignored if the file doesn’t exist on the device.
@PJL LDELETEFILE DEVICE = filedevice FILENAME = "fname"[]
Use this command to format a device for storage.
@PJL LFORMAT DEVICE = filedevice[]
Use this command to recover storage space on a flash device.
@PJL LDEFRAG DEVICE = flashdevice[]

File and Device Protection Commands
The following information applies to password protection.
– You can create/change passwords for the whole flash multiple times, but
each change uses up free space in the flash that can only be recovered by reformatting the whole flash. – You can create passwords for individual resources on the flash only once.
You can also delete this password once. If this is done, you must recreate the resource before using the password feature again.
Use the DEFAULT command to set a password on the entire flash or disk or on an individual macro or font in flash.
LRWLOCK with DEFAULT specified locks a file or device for reading and writing. LWLOCK with DEFAULT specified locks a file or device for writing only.

@PJL DEFAULT LRESOURCE:"device:filename.filetype" LRWLOCK="password"[]
@PJL DEFAULT LRESOURCE:"device:filename.filetype" LWLOCK="password"[]
The filename used depends on whether you wish to put a password on a font or a macro.
The filename for a font is a five digit ID from the print directory page (add zeros to the left of the ID to fill the five digits) followed by a three digit instance number. The first time a font is downloaded after a flash has been formatted, the instance number is 0. Filetypes are described under filename in “Table 3-9: Printer Unique LRESOURCE Variables” on page 3-53. For example, to write password protect a PCL emulation bitmapped font (filetype of p5bitmap) with an ID of 127, which has not been downloaded since flash was formatted:
@PJL DEFAULT LRESOURCE:"flash:00127000.p5bitmap"
To password protect a macro, the filename is the ID taken from the print directory page, followed by the filetype. For example, to read/write password protect a PCL emulation macro (filetype is p5macro) saved to flash with an ID of 1023:
@PJL DEFAULT LRESOURCE:"flash:1023.p5macro"
device.
If you want to set a password on a device, not just a single file, omit the filename. LRWLOCK with DEFAULT specified locks a device for reading and writing. LWLOCK with DEFAULT specified locks a device for writing only.
@PJL DEFAULT LRESOURCE:"device:" LRWLOCK="password"[]
@PJL DEFAULT LRESOURCE:"device:" LWLOCK="password"[]
LWLOCK="password"[] · LRWLOCK="password"[]

Unlocking a Protected File or Device
Use the LDECLARE command to specify a password so a protected file or device may be accessed or “unlocked.” The LDECLARE command is only allowed within a JOB/ EOJ combination.
LRWLOCK with LDECLARE specified unlocks a file or device for reading and writing. LWLOCK with LDECLARE specified unlocks a file or device for writing only. The file or device must be re-locked using the LDELETEPASSWORD command after the job is completed. The file or device is not automatically re-locked with the EOJ command.
Values for "device:filename.filetype" are:
device flash, flash1, disk, or disk1 (case insensitive)
filename A unique identifier for a file, such as the macro ID for a PCL macro, the symbol set ID for a PCL symbol set, the font ID for a PCL font, or the actual file name for data, Type 1 fonts, and demo files as shown on the Directory. The filename is case sensitive.
filetype An identifier that categorizes the file, such as p5macro for PCL macros or p5symset for PCL symbol sets. See the table beginning on page 3-87 for a complete list of the supported file types. The filetype is case sensitive.
LRWLOCK = "password" or LWLOCK = "password"
See “Printer Unique LRESOURCE Variables” on page 3-52 for information about values for LRWLOCK = "password" and LWLOCK = "password" parameters.
command. See “Password Protection for a File” on page 3-93 and “Password for an Entire Device” on page 3-94 for examples.

Re-Locking a Protected File or Device
Use the LDELETEPASSWORD command to re-lock a password-protected file or device that has been unlocked using the LDECLARE command.
If an LRESOURCE is not specified, all unlocked files or devices are re-locked.
Values for "device:filename.filetype" are:
device flash, flash1, disk, or disk1 (case insensitive)
filename A unique identifier for a file, such as the macro ID for a PCL macro, the symbol set ID for a PCL symbol set, the font ID for a PCL font, or the actual file name for data, Type 1 fonts, and demo files as shown on the Directory. The filename is case sensitive.
filetype An identifier that categorizes the file, such as p5macro for PCL macros or p5symset for PCL symbol sets. See the table beginning on page 3-87 for a complete list of the supported filetypes. The filetype is case sensitive.

Unlocking a Protected File or Device for the Current Job
The file or device unlocked by the execution of this command is automatically re-locked upon execution of the EOJ command or by a printer language change.
Values for "device:filename.filetype" are:
device flash, flash1, disk, or disk1 (case insensitive)
filename A unique identifier for a file, such as the macro ID for a PCL macro, the symbol set ID for a PCL symbol set, the font ID for a PCL font, or the actual file name for data, Type 1 fonts, and demo files as shown on the Directory. The filename is case sensitive.
filetype An identifier that categorizes the file, such as p5macro for PCL macros or p5symset for PCL symbol sets. See the table beginning on page 3-87 for a complete list of the supported file types. The filetype is case sensitive.
LRWLOCK = "password" or LWLOCK = "password" Parameters
See “Printer Unique LRESOURCE Variables” on page 3-52 for information about values for LRWLOCK = "password" and LWLOCK = "password" parameters.

Recovering Lost Passwords
Use the LQUERYSEED and LBYPASSPASSWORD commands to recover lost passwords.
@PJL LQUERYSEED[<CR>]<LF>
@PJL LBYPASSPASSWORD KEY = "key"[]
Use the following steps to retrieve lost passwords:
1 Send the LQUERYSEED command to the printer by one of the host computer interfaces.
This command causes a value, the “seed,” to display on the printer operator panel, through MarkVision Professional or, if there isn’t an LCD panel, to print on the Menu Settings Page. The value of the “seed” determines the key.
2 Obtain the key from the Lexmark Customer Support Center.
You must have the “seed” value.
3 Send the @PJL LBYPASSPASSWORD command to the printer by any port.
If the correct key is specified, a modified version of the directory is produced. The directory indicates the appropriate passwords for the flash or disk.

CHAPTER 4: PostScript Emulation
This section explains PostScript emulation supplemental operators in detail. For more information, refer to the PostScript Language Reference Manual (Third Edition) by Adobe Systems, Inc.
To determine which commands your printer supports, see Appendix C: “PostScript Support” on page C-1.
Using SmartSwitch
When SmartSwitch is enabled for both printer languages on an interface, the printer automatically switches to the printer language being sent by your software program. The printer is shipped with SmartSwitch enabled for both printer languages and all interfaces. The printer examines all print jobs and switches dynamically between PostScript emulation and PCL emulation.
You may select PostScript emulation from the printer operator panel or through MarkVision Professional. To disable the automatic switching and have all input interpreted as PostScript language, turn PCL SmartSwitch Off and set the printer language default to PostScript emulation. Refer to your printer user documentation for information on changing menu settings.

Using Your Software Program
To select PostScript emulation, use the ENTER LANGUAGE command, which is a Printer Job Language (PJL) command. See “ENTER LANGUAGE Command” on page 3-3. See “Printer Job Language” on page 3-1 for syntax and use of PJL.
downloaded fonts and macros, unless Resource Save is set to On or the resources are stored in flash memory or on disk.

Page Formatting
The printable areas and logical pages for PostScript emulation, both portrait and landscape orientation, are illustrated below. See the Legend that follows for definitions of areas A through F.
A Distance between the edge of the physical page and the printable area for the left side of a portrait page; distance between the edge of the physical page and the printable area for the top of a landscape page
B Portrait printable area width; landscape printable area length
C Portrait printable area length; landscape printable area width
D Distance between the edge of the physical page and the printable area for the top of a portrait page; distance between the edge of the physical page and the printable area for the left side of a landscape page
E Distance between the edge of the physical page and the printable area for the right side of a portrait page; distance between the edge of the physical page and the printable area for the bottom of a landscape page
F Distance between the edge of the physical page and the printable area for the bottom of a portrait page; distance between the edge of the physical page and the printable area for the right side of a landscape page
Portrait Landscape

Logical Page Size
See the following tables for the logical page size dimensions your printer supports. If information about your printer is not included in the following tables, see page 1-1 for information on how to get a Technical Reference for your printer.
The following table lists the exact width and length of the printable areas for all paper and envelope sizes the Lexmark C510(n) printer supports. Areas A through F in the table are described in the Legend under “Printable Areas” on page 4-3.
Selection Paper Dimensions Dimensions by Area (pels) in 600th of an Inch
Name Millimeters Inches A B C D E F
A4 (203 mm) 210 x 297 8.3 x 11.7 80 4810 6814 100 70 100
A5 148 x 210 5.83 x 8.27 100 3296 4760 100 100 100
JIS B5 Paper 182 x 257 7.2 x 10.1 100 4114 5870 100 86 100
Executive 184 x 267 7.25 x 10.5 100 4150 6100
Folio1 216 x 330 8.5 x 13 100 4900 7600 100 100 100
Letter 216 x 279 8.5 x 11 100 4900 6400 100 100 100
Legal1 216 x 356 8.5 x 14 100 4900 8200 100 100 100
Statement 140 x 216 5.5 x 8.5 100 3100 4900 100 100 100
Universal1 216 x 356 8.5 x 14 100 4900 8200 100 100 100
DL 110 x 220 4.33 x 8.66 100 2482 4996 100 16 100
C5 162 x 229 6.38 x 9.02 100 3698 5208 100 28 100
B5 Envelope 176 x 250 6.93 x 9.84 100 4048 5704 100 8 100
Other Envelope1 216 x 356 8.5 x 14 100 4900 8200 100 100 100
9 (Com 9) 98 x 225 3.875 x 8.875 100 2224 5124 100 2 100
10 (Com 10) 105 x 241 4.125 x 9.5 100 2352 5500 100 22 100
1 The Lexmark C510(n) supports this size media only with an optional legal tray.
Paper · Envelope

The following table lists the exact width and length of the printable areas for all paper and envelope sizes the Lexmark X422 printer supports. Areas A through F in the table are described in the Legend under “Printable Areas” on page 4-3.
Selection Paper/Envelope Dimensions Dimensions by Area (pels) in 600th of an Inch
Name Millimeters Inches A B C D E F
JIS B4 257 x 364 10.1 x 14.3 100 5870 8400 100 100 100
JIS B5 Paper 182 x 257 7.2 x 10.1 100 4114 5870 100 86 100
A4 (203 mm) 210 x 297 8.3 x 11.7 80 4828 6814 100 52 100
A5 148 x 210 5.83 x 8.27 100 3296 4760 100 100 100
Executive 184 x 267 7.25 x 10.5 100 4150 6100
Folio 216 x 330 8.5 x 13 100 4900 7600 100 100 100
Letter 216 x 279 8.5 x 11 100 4900 6400 100 100 100
Legal 216 x 356 8.5 x 14 100 4900 8200 100 100 100
Statement 140 x 216 5.5 x 8.5 100 3100 4900 100 100 100
Universal 216 x 356 8.5 x 14 100 5100 8500 100 100 100
DL 110 x 220 4.33 x 8.66 100 2482 4996 100 16 100
C5 162 x 229 6.38 x 9.02 100 3698 5208 100 28 100
B5 Envelope 176 x 250 6.93 x 9.84 100 4048 5704 100 8 100
Other Envelope 216 x 356 8.5 x 14 100 4900 8200 100 100 100
7-3/4 Monarch 98 x 191 3.875 x 7.5 100 2224 4300 100 2 100
9 (Com 9) 98 x 225 3.875 x 8.875 100 2224 5124 100 2 100
10 (Com 10) 105 x 241 4.125 x 9.5 100 2352 5500 100 22 100
Paper · Envelope

The following table lists the exact width and length of the printable areas for all paper and envelope sizes the Lexmark E230, E232, E234(n), E330, and E332 printers support. Areas A through F in the table are described in the Legend under “Printable Areas” on page 4-3.
Selection Paper/Envelope Dimensions Dimensions by Area (pels) in 600th of an Inch
Name Millimeters Inches A B C D E F
JIS B4 257 x 364 10.1 x 14.3 100 5870 8400 100 100 100
JIS B5 Paper 182 x 257 7.2 x 10.1 100 4114 5870 100 86 100
A4 (203 mm) 210 x 297 8.3 x 11.7 80 4828 6814 100 52 100
A5 148 x 210 5.83 x 8.27 100 3296 4760 100 100 100
Executive 184 x 267 7.25 x 10.5 100 4150 6100
Folio 216 x 330 8.5 x 13 100 4900 7600 100 100 100
Letter 216 x 279 8.5 x 11 100 4900 6400 100 100 100
Legal 216 x 356 8.5 x 14 100 4900 8200 100 100 100
Statement 140 x 216 5.5 x 8.5 100 3100 4900 100 100 100
Universal 216 x 356 8.5 x 14 100 5100 8500 100 100 100
DL 110 x 220 4.33 x 8.66 100 2482 4996 100 16 100
C5 162 x 229 6.38 x 9.02 100 3698 5208 100 28 100
B5 Envelope 176 x 250 6.93 x 9.84 100 4048 5704 100 8 100
Other Envelope 216 x 356 8.5 x 14 100 4900 8200 100 100 100
7-3/4 Monarch 98 x 191 3.875 x 7.5 100 2224 4300 100 2 100
9 (Com 9) 98 x 225 3.875 x 8.875 100 2224 5124 100 2 100
10 (Com 10) 105 x 241 4.125 x 9.5 100 2352 5500 100 22 100
Paper · Envelope

PostScript Emulation Fonts for the Lexmark X422
The Lexmark X422 printer has 91 resident fonts in PostScript emulation.

PostScript emulation also has a backward compatibility mode that changes the metrics of eight of the resident fonts to match the fonts in the Lexmark Optra S family of printers. The eight fonts are:
unavailable.
Your printer defaults to the forward compatibility mode and the Lexmark PostScript driver uses this mode. For backward compatibility with the Lexmark Optra S family of printers, use the latest version of the Lexmark Optra S driver which sends the PostScript command to switch to backward compatibility mode. (The original Lexmark Optra S driver does not send this command.)
See Table 4-4 to determine which Lexmark Optra S driver you should use.
If you need the Lexmark Optra S driver for ... Use ...
Windows 2000, WindowsXP Version 7.2 or later of LEXPSNT
Windows NT 4.0 Version 1.8 or later of LEXPSNT
Windows 9x, Windows Millennium Edition (Me) Version 4.32 or later of LEXPS
Windows 3.x Version 4.02 or later of LEXPS
The PostScript commands to switch the compatibility modes are:
statusdict begin PS3fonts end (temporary, changes the PostScript job only)
setsystemparams (permanent, changes the default in NVRAM)
statusdict begin PS2fonts end (temporary, changes the PostScript job only)
setsystemparams (permanent, changes the default in NVRAM)
With the appropriate printer driver installed and selected, your software application enumerates and selects the available PostScript fonts.

PostScript Emulation Fonts for the Lexmark C510(n)
The Lexmark C510(n) printer has 158 resident fonts in PostScript emulation. The fonts match the 136 Adobe PostScript 3 resident fonts and include 22 extra fonts. Since the fonts are designed to match Adobe PostScript 3, this is called forward compatibility mode. The following table lists the 158 resident fonts in PostScript emulation.


PostScript emulation also has a backward compatibility mode that changes the metrics of eight of the resident fonts to match the fonts in the Lexmark Optra S family of printers. The eight fonts are:
unavailable.
Your printer defaults to the forward compatibility mode and the Lexmark PostScript driver uses this mode. For backward compatibility with the Lexmark Optra S family of printers, use the latest version of the Lexmark Optra S driver which sends the PostScript command to switch to backward compatibility mode. (The original Lexmark Optra S driver does not send this command.)
See Table 4-5 to determine which Lexmark Optra S driver you should use.
If you need the Lexmark Optra S driver for ... Use ...
Windows 2000, WindowsXP Version 7.2 or later of LEXPSNT
Windows NT 4.0 Version 1.8 or later of LEXPSNT
Windows 9x, Windows Millennium Edition (Me) Version 4.32 or later of LEXPS
Windows 3.x Version 4.02 or later of LEXPS
The PostScript commands to switch the compatibility modes are:
statusdict begin PS3fonts end (temporary, changes the PostScript job only)
setsystemparams (permanent, changes the default in NVRAM)
statusdict begin PS2fonts end (temporary, changes the PostScript job only)
setsystemparams (permanent, changes the default in NVRAM)
With the appropriate printer driver installed and selected, your software application enumerates and selects the available PostScript fonts.

PostScript Emulation Fonts for the Lexmark E234(n), E330, E332n
The Lexmark E234(n), E330, and E332n printers have 91resident fonts in PostScript emulation. Since the fonts are designed to match Adobe PostScript 3, this is called forward compatibility mode. The following table lists the 91resident fonts in PostScript emulation.

PostScript emulation also has a backward compatibility mode that changes the metrics of 8 of the resident fonts to match the fonts in the Lexmark Optra S family of printers. The 8 fonts are:
unavailable.
Your printer defaults to the forward compatibility mode and the Lexmark PostScript driver uses this mode. For backward compatibility with the Lexmark Optra S family of printers, use the latest version of the Lexmark Optra S driver which sends the PostScript command to switch to backward compatibility mode. (The original Lexmark Optra S driver does not send this command.)
See Table 4-6 to determine which Lexmark Optra S driver you should use.
If you need the Lexmark Optra S driver for ... Use ...
Windows 2000, Windows XP Version 7.2 or later of LEXPSNT
Windows NT 4.0 Version 1.8 or later of LEXPSNT
Windows 9x, Windows Millennium Edition (Me) Version 4.32 or later of LEXPS
Windows 3.x Version 4.02 or later of LEXPS
The PostScript commands to switch the compatibility modes are:
statusdict begin PS3fonts end (temporary, changes the PostScript job only)
setsystemparams (permanent, changes the default in NVRAM)

statusdict begin PS2fonts end (temporary, changes the PostScript job only)
setsystemparams (permanent, changes the default in NVRAM)
With the appropriate printer driver installed and selected, your software program enumerates and selects the available PostScript fonts.
This section explains PostScript emulation supplemental operators in detail. These supplemental operators are extensions to the standard PostScript language. For each supplemental operator, the exact syntax is listed, as well as the values returned on the stack and possible error messages.
To determine which operators your printer supports, see Table C-1 on page C-1.
The PostScript emulation supplemental operators are described in this chapter in the following format:

Brief description of the command function.
Description of variables.
The operators in this section relate to the paper used in the printer.
The literal names described in the following table are also supported as operators in userdict. When the literal names are used as operators:
Therefore, PageSize applies to the media currently installed in the tray without disabling media selection, which may clip the image. For example, if you execute the legal operator when letter size paper is installed, part of the image is clipped from the page.
When the literal names are used as operators, the action is equivalent to executing the following PostScript emulation sequence. This example uses letter-size paper.
/PageSize [612 792] >> setpagedevice
Refer to your printer user documentation for a list of supported paper sizes.
— nameofoperator variable

Supported ✘ Not Supported
Paper Sizes Printer Model
Literal Name Size (mm) Size (inches) Size (points)
letter 215.9 x 279.4 8.5 x 11.0 612 x 792
legal2 215.9 x 355.6 8.5 x 14.0 612 x 1008
b51 182.0 x 257.0 7.17 x 10.1 516 x 729
a4 210.0 x 297.0 8.27 x 11.7 595 x 842
executivepage 184.2 x 266.7 7.25 x 10.5 522 x 756
a5 148.0 x 210.0 5.83 x 8.27 419 x 595
b4 257 x 364 10.12 x 14.33 729 x 1032 ✘ ✘ ✘
a3 297 x 420 11.7 x 16.54 842 x 1191 ✘ ✘ ✘
a3+ 328 x 453 12.91 x 17.83 930 x 1284 ✘ ✘ ✘
11x17 279.4 x 431.8 11 x 17 792 x 1224 ✘ ✘ ✘
ledger 431.8 x 279.4 17 x 11 1224 x 792 ✘ ✘ ✘
folio2 216 x 330 8.5 x 13 612 x 936
statement 140 x 216 5.5 x 8.5 396 x 612
custom2 215.9 x 355.6 8.5 x 14.0 612 x 1020
custom 297 x 431.8 11.7 x 17 842 x 1224 ✘ ✘ ✘
custom 320 x 559 12.6 x 22 908 x 1584 ✘ ✘ ✘
custom 297 x 914 11.7 x 36 842 x 2592 ✘ ✘ ✘
1 B5 is a Japanese Industry Standard (JIS) paper size. The same B5 designation is used by JIS and International Standards Organization (ISO) for different paper sizes. 2 The Lexmark C510(n) supports this size media only with an optional legal tray.
C510(n) · E23x · E33x

— currentuniversalsize integer integer integer (string)
queries the current settings for the Universal paper size. Three integers and one string are returned on the stack:
Universal Width Universal Height Universal Feed Direction Custom Universal Prompt String
queries whether or not text is being oriented based on page size.
An integer value is returned on the stack:
0 perform automatic orientation of text based on page size
1 treat the page size as an envelope
2 treat the page size as paper
overrides the automatic page orientation selected by the printer to support custom media sizes. This operator determines whether or not to adjust the text based on the page size.
integer value may be:
0 perform automatic orientation of text based on page size (default)
1 treat the page size as an envelope
2 treat the page size as paper
A value set by this operator takes effect on a subsequent setpagedevice only if PageSize Policy is set to 7.
— ignoresize integer · integer setignoresize —

— integer integer integer (string) setuniversalsize
changes the current settings for the Universal paper size. Each parameter on the stack indicates:
Universal Width minimum to maximum width in points Universal Height minimum to maximum height in points Universal Feed Direction
1 long edge Custom Universal Prompt String String must be 16 characters or less.
When the printer receives one of the operators listed in “Table 4-8: Tray Selected with Tray Operators” on page 4-20, it performs the actions listed as follows. This paper tray selection process ends as soon as a suitable paper source is chosen and paper is fed from this tray.
0 short edge

– Tray 1 – Tray 2 – Tray 3 – Multipurpose Feeder – Tray 4 – Tray 5 • If the requested size cannot be located in any automatic source, a configurationerror is issued and the job is flushed.
For printers that support automatic duplexing:
When these operators are used, it is equivalent to executing the following PostScript emulation sequence:
>>
where x y are the PageSize in points.
setpagedevice

Supported ✘ Not Supported Printer Model
Tray Selected (Corresponding image size is set)
a3tray tray with A3 size paper ✘ ✘ ✘
a4tray tray with A4 size paper
a5tray tray with A5 size paper
b4tray tray with B4 size paper ✘ ✘ ✘
b5tray tray with B5 size paper
customtray tray with custom size paper ✘ ✘ ✘
executivetray tray with executive size paper
foliotray tray with folio size paper
ledgertray tray with ledger size paper ✘ ✘ ✘
legaltray tray with legal size paper
lettertray tray with letter size paper
statementtray tray with statement size paper
11x17tray tray with 11 x 17 size paper ✘ ✘ ✘

in statusdict indicates if a manual feed source has been selected. The boolean value can be:
true prints from a manual feed source (default)
false prints from an automatic feed source
This boolean key can be redefined to affect manual feed for the current job.
If the value of the manualfeed operator or the ManualFeed page device parameter is true when showpage or copypage is executed, the page is fed manually. If both have a value of false when showpage or copypage is executed, the page is fed from an automatic source. These two values are independent of each other.
queries the paper tray that is currently selected. An integer is returned on the stack indicating which paper tray is currently in use. Valid integers are:
2 Multipurpose Feeder or Envelope Feeder

changes the active paper source for the next page through the end of job by setting the PageSize entry in the page device to the size loaded in the selected source and by setting MediaPosition to the selected source. This operator executes a setpagedevice.
The PageSize Policy page device parameter is not altered by this operator.
Use the following integers to set the paper tray:
2 Multipurpose Feeder or Envelope Feeder
The setting returns to the user default setting for the Paper Source menu item at the end of the print job.

Envelope Size Support
The literal names in Table 4-9 are also supported as operators in userdict. These operators change the image size, but do not change the active paper source. Therefore, when these operators are used, part of the image may be clipped.
When these literal names are used as operators, it is equivalent to executing the following PostScript emulation sequence. The following example uses a 3.875 x 7.5 envelope.
>>setpagedevice
Supported ✘ Not Supported
Literal Name Size (mm) Size (inches) Size (points)
3.875x7.5envelope 98.4 x 190.5 3.875 x 7.5 [279 540] ✘
3.875x8.875envelope 98.4 x 225.4 3.875 x 8.875 [279 639]
4.125x9.5envelope 104.8 x 241.3 4.125 x 9.5 [297 684]
110x220envelope 110 x 220 4.33 x 8.66 [312 624]
162x229envelope 162 x 229 6.38 x 9.01 [459 649]
176x250envelope 176 x 250 6.93 x 9.84 [499 708]
otherenvelope1 Other [612 996]
otherenvelope Other [841 842] ✘ ✘ ✘
1 For other envelopes, the page is formatted to 216 x 356 mm (8.5 x 14 in.) unless a size is specified by your software program.

The literal names in Table 4-10 are supported as PostScript emulation compatible operators.
Supported ✘ Not Supported
Literal Names Printer Model
Literal Name Compatible Literal Name
monarcenvelope 3.875x7.5envelope ✘
com10envelope 4.125x9.5envelope
dlenvelope 110x220envelope
c5envelope 162x229envelope
b5envelope 176x250envelope ✘ ✘ ✘
requested and one of the envelope size operators is sent to the printer, duplexing is suspended until a paper size is requested that is supported for duplex printing.
C510(n) · E23x · E33x

Envelope Tray Support
If manualfeed in statusdict and the ManualFeed page device parameter are false when the printer receives one of the envelopetray operators listed in “Table 4-11: Envelopetray Operator Selections” on page 4-26, the printer:
– Envelope Feeder – Multipurpose Feeder • If the requested size and type is not available from any automatic source, you are prompted to load the requested envelope size and type in the manual feed source.
If manualfeed or ManualFeed is true, the printer prompts you to load the requested size manually. If no manual feed exists on the printer, a rangecheck error message is generated.
The envelope tray the printer selects when it receives an envelopetray operator is listed in Table 4-11. These operators are equivalent to executing the following PostScript emulation sequence:
where x y are the PageSize in points.
setpagedevice

Supported ✘ Not Supported
Tray Operators Printer Model
Operator Tray Selected (Corresponding image size is set)
110x220envelopetray tray with 110 x 220 size envelopes
dlenvelopetray tray with 110 x 220 size envelopes
162x229envelopetray tray with 162 x 229 size envelopes
c5envelopetray tray with 162 x 229 size envelopes
176x250envelopetray tray with 176 x 250 size envelopes
b5envelopetray tray with 176 x 250 size envelopes
3.875x7.5envelopetray tray with 3.875 x 7.5 size envelopes ✘
monarcenvelopetray tray with 3.875 x 7.5 size envelopes ✘
3.875x8.875envelopetray tray with 3.875 x 8.875 size envelopes
4.125x9.5envelopetray tray with 4.125 x 9.5 size envelopes
com10envelopetray tray with 4.125 x 9.5 size envelopes
otherenvelopetray tray with other size envelopes
C510(n) · E23x · E33x

Supplemental Operator Summary
To determine which operators your printer supports, see Table C-1 on page C-1.
in statusdict, this string reflects the current value of the LocalTalkType device parameter from the %LocalTalk% device. The default string is LaserWriter. To change the type portion (appletalktype) of the AppleTalk network name and redefine the string, execute the following:
/appletalktype (string) def
When you redefine a string inside the normal server loop, it is reset to the default value at the end of the print job. When you define it outside the normal server loop, it is reset to the default value when the printer is switched to a printer language other than PostScript emulation or when a power-on reset occurs.
returns the BuildTime system parameter, which is a timestamp that identifies the specific build of the PostScript emulation interpreter.
returns a boolean on the stack with the same value as the system parameter ByteOrder. Indicates the printer microprocessor native byte order. The boolean values indicate:
true low-order byte first
false high-order byte first
— appletalktype (string) · — buildtime integer · byteorder boolean

integer checkpassword or (string) checkpassword
checks the passwords for both the SystemParamsPassword system parameter and the StartJobPassword system parameter stored in the printer.
If the integer form is used, the integer is converted into a string before the password check occurs. A boolean is returned on the stack to indicate if the specified password matches either password. The boolean value can be:
After the boolean is returned, the printer waits 1 second before it continues processing.
returns a boolean on the stack to indicate whether the extension should be automatically added to any filename. The boolean value is either:
true adds the extension
false does not add the extension
See “Filename Extensions” on page 6-10.
queries the current value of the manual duplex mode. An integer is returned on the stack:
0 current job manual duplex mode is no manual duplex
1 current job manual duplex mode is printing first sides of job
2 current job manual duplex mode is printing second sides of job

— defaulttimeouts job manualfeed wait
queries the user default settings of all timeouts. Three integers are returned on the stack:
15...65535 seconds
1...65535 seconds (default is device dependent)
To find the default for your printer, see Table C-2 on page C-4.
15...65535 seconds (default is 40 seconds)
deletes the specified file from the disk. This operator is in systemdict.

string integer devcontrol boolean
allows a host computer utility to manage resources on the flash or disk. It requires a string device name parameter, an integer command name parameter, and two command argument parameters. The device control operator performs a specified command on the specified device. The return values on the stack indicate:
true the command is successful
false the command is unsuccessful and returns an error code
Integer Command Name Parameter Argument Parameter Description
1 null null Park disk heads
5 file null Make contiguous flash file
8 filename description Set description of file
9 password null Set device read/write password
10 password null Set device write password
11 filename password Set file read/write password
12 filename password Set file write password
13 password null Declare device read/write password
14 password null Declare device write password
15 filename password Declare file read/write password
16 filename password Declare file write password
17 null null Reset device password list
18 null null Reset file password list
19 devicename password Get device password
19 filename password Get file password
20 devicename null Determine if device password is properly declared
20 filename null Determine if file password is properly declared
21 null null Scan for bad block
22 null null Abort bad block scan
23 null null Quick bad block scan
24 null null Flush the disk cache
27 file null Be quiet when writing to disk

1 File system access has not been initialized
2 Could not allocate file descriptor
3 Some invalid argument was passed
4 No such device
5 Invalid access to file requested
6 Argument too large (filename, buffer)
7 Invalid file descriptor or filename
8 Catch all error or device error
9 Unable to allocate memory for buffer, data structure
11 Device not currently mounted
12 Attempt to perform illegal IO operation
13 No space to update or create file
14 Major change in file system for findnext() to function properly
15 Corrupted file system on device
16 Device already mounted
17 Could not initialize file system
18 Device not mounted
19 No file entry located
20 Bad file system on device
22 Aborted by callback
dismounts the specified device by setting the Mounted device parameter for the specified device to false. This operator is in systemdict.

proc scratchstring devforall —
executes the specified proc procedure for each storage device after pushing a substring on the stack that is the portion of the scratch string containing the device name. This operator is in systemdict.
devformat
devicename pages action devformat —
formats (erases all data from) the specified device. This operator is in systemdict.
pages Sets the LogicalSize device parameter for the specified device:
0 entire device is formatted
1,2,3 an ioerror occurs
action 1 is added to the action argument. The result is used for the InitializeAction device parameter for the same device.
A devformat on a flash device formats the entire device regardless of the LogicalSize specified.

sets the Mounted device parameter for the specified device to true. It also returns the value of the Mounted device parameter for the specified device. This operator is in systemdict.
The boolean values indicate:
true device successfully mounted, or was already mounted
false device not mounted
If a device with the specified device name is not installed, an undefinedfilename error occurs.
This operator may change the search order. See “Device Search Order” on page 6-12.
devicename devstatus false or devicename devstatus searchable writeable hasnames mounted removable searchorder free size true
returns on the stack the status of a specified device. This operator is in systemdict. A value of false is returned if the device is not present. If the device is present, five boolean values and three integers (see the following description) followed by a value of true are returned.
The five boolean values are:
true, if the device is included in the search order and is to be searched for the file operators that do not specify a device name. Same as the value of the Searchable device parameter from the specified IODevice.
true, if the device can be written to. This value is the same as the Writeable device parameter from the specified IODevice.
true, if the device supports named files. This value is the same as the HasNames device parameter from the specified IODevice.
device devmount boolean

true, if the device is mounted. This value is the same as the Mounted device parameter from the specified IODevice.
true, if the device is removable and must be mounted before it is referenced. This value is the same as the Removable device parameter from the specified IODevice.
The three integers are:
The position in the search order. This value is the same as the SearchOrder device parameter from the specified IODevice.
The number of free bytes on the device. This value is the same as the Free device parameter from the specified IODevice.
The total number of bytes on the device. This value is the same as the LogicalSize device parameter from the specified IODevice.
returns the value of the Writeable device parameter (which is a boolean) for the %disk1% IODevice.
This operator is equivalent to executing the following PostScript emulation sequence:
(%disk1%) currentdevparams /Writeable get
— diskonline boolean

— diskstatus free logicalsize
returns on the stack the following two integers:
This operator is equivalent to executing the following PostScript emulation sequence:
(%disk1%) currentdevparams dup /Free get exch /LogicalSize get
sets a custom paper message. The string parameter is used as a prompt string when a page prints. The string value can be any string up to 16 characters. The string is cleared at the end of a print job.
returns a constant boolean value of false.
(string) displayoperatormsg · — doidlefonts false

queries the user default setting of the Jam Recovery menu item. A boolean value is returned on the stack:
true reprint jammed page (Jam Recovery is set to On) (default)
false do not reprint jammed page (Jam Recovery is set to Off)
This operator is equivalent to executing the following PostScript emulation sequence:
returns a boolean with the same value as the system parameter DoPrintErrors. It also indicates the current value of the Print PS Error printer setting. The DoPrintErrors system parameter must be present for the doprinterrors operator to be present.
returns the PQET setting for the current print job. An integer value is returned on the stack:
This operator is equivalent to executing the following PostScript emulation sequence:
currentpagedevice /PostRenderingEnhanceDetails get /REValue get

returns a boolean with the same value as the system parameter DoStartPage. The DoStartPage system parameter must be present for the compatibility operator dostartpage to be present.
returns the current value of the StartupMode system parameter. A boolean value is returned:
true StartupMode set to 1 or 11
false StartupMode other than 1 or 11
This operator is equivalent to executing the following PostScript emulation sequence:
queries if a duplex unit is installed. A boolean value is returned on the stack:
true duplex unit is installed
false duplex unit is not installed

queries the current value for the Duplex page device parameter.
true printing mode is duplex
false printing mode is simplex
This operator is equivalent to executing the following PostScript emulation sequence:
indicates if the printer waits for the last page of a job to print before returning a Ctrl-D to the host computer.
— duplexmode boolean · currentpagedevice /Duplex get · — enginesync boolean

filename access file file
creates a file object with specified filename and access. The access values are:
r open the file for reading only
w create a file if one does not already exist, or truncate and overwrite it if it does exist. File is opened for writing only.
a create a file if one does not already exist or append it if it does exist. File is opened for writing only.
r+ open the file for reading and writing. An undefinedfilename error occurs if the file does not exist.
w+ create a file if it does not already exist, or truncate and overwrite if it does exist. File is opened for reading and writing.
a+ create a file if it does not exist or append it if it does exist. File is opened for reading and writing.
This operator is in systemdict.
pattern proc scratchstring filenameforall
lists all the files with names that match a specified pattern string, copies the filename for each of these files into a specified scratch string, and calls a specified proc procedure. This operator is in systemdict.
indicates the current position on an open file. This operator is in systemdict.
file fileposition position

indicates whether the current imaging area is on the front side of the page.
true front side is currently being imaged
false back side is currently being imaged
sets the winding rule for Type 1 fonts. No query operation is performed since the winding rule is reset to true at the beginning of each print job. The boolean value can be:
true non-zero winding used by the interpreter
false even or odd winding rule used by interpreter
queries the user default setting of the Parallel Protocol menu item. This operator returns the value of the Parallel Protocol, either Standard or Fastbytes. An
integer value is returned on the stack:
1 Parallel Fastbytes Off (Standard)
2 Parallel Fastbytes On (Fastbytes)
supports compatibility with the IBM LaserPrinters 4019, 4029, and 4039. It is parsed and returns a mark on the stack.

See page 4-17.
pages action initializedisk —
initializes the disk with the page count and action as integer arguments. The arguments set the (%disk1%) IO device parameters as follows:
identifies each print job selection. This string in statusdict queries and changes the current setting of the JobName user parameter. Originally, jobname is set to null.
currentuserparams /JobName get.
A string indicating the job name is returned on the stack.
> setuserparams
where string is the new job name.
— jobname (string)

indicates the current value of the CurInputDevice system parameter. A string is returned on the stack indicating the job source. Valid values are:
%LocalTalk% %SerialA% %SerialB% %SerialC% %SerialD% %ParallelA% %ParallelB% %ParallelC% %ParallelD% %IR_A% %IR_B% %IR_C% %IR_D% %USB_A% %USB_B% %USB_C% %USB_D% %EtherTalkB% %EtherTalkC% %EtherTalkD% %TokenTalkB% %TokenTalkC% %TokenTalkD% %LexLinkB% %LexLinkC% %LexLinkD% %PrintServerB% %PrintServerC% %PrintServerD% %RemotePrinterB% %RemotePrinterC% %RemotePrinterD% %AppSocketB% %AppSocketC% %AppSocketD%
— jobsource (string)

%LPR_B% %LPR_C% %LPR_D% %UnknownDevice%
This operator is equivalent to executing the following PostScript emulation sequence:
queries the current user default setting for the JobTimeout parameter. An integer is returned on the stack:
15...65355 seconds
This operator is equivalent to executing the following PostScript emulation sequence:
See page 4-21.

is an integer key in statusdict that works with the ManualFeedTimeout page device parameter to determine the manualfeed timeout for a given page.
If during a print job, manualfeedtimeout is defined as an integer value in statusdict, that value is used instead of the ManualFeedTimeout page device parameter.
The value of the ManualFeedTimeout page device parameter and manualfeedtimeout key in statusdict are independent of each other; the value of one does not affect the value of the other.
1...65355 seconds
An undefined error results if manualfeedtimeout is queried before the value is set.
causes the current page to start on the front side of a new sheet.
queries the value of the PageCount system parameter. An integer is returned on the stack indicating the current page count.
This operator is equivalent to executing the following PostScript emulation sequence:

queries the number of pages of the current job submitted by the PostScript interpreter to the printer.
See page 4-21.
returns the value of the PrinterName system parameter that is defined by the
setprintername operator. The value of the string defines the printer name. A maximum of 32 characters are returned on the stack.
This operator is equivalent to executing the following PostScript emulation sequence:
queries the name of the product that is defined in statusdict. A string is returned on the stack indicating the name of the product. The product string in systemdict cannot be changed.
To change this product string in statusdict:

redefines the following PostScript resident fonts to match the character designs and metrics defined in PostScript Level 2. The font names in parentheses are the equivalent PostScript 3 font names for the associated PostScript Level 2 names.
Antique Olive (Antique Olive Roman)
Letter Gothic Italic (Letter Gothic Slanted)
restores the font compatibility to PostScript 3.
queries the PowerSave page device parameter. An integer is returned on the stack:
0 Power Saver is Off
1 to 120 or 1 to 240 (Model specific) Number of minutes elapsed after last page prints before Power Saver is invoked.
Power Saver reduces power consumption when the printer is idle. When quiet is enabled, it takes longer to print the first page after the printer has been idle.

Star printers cannot have Power Saver disabled.
This operator is equivalent to executing the following PostScript emulation sequence:
queries the current setting of the RamSize system parameter. An integer is returned on the stack showing total RAM in bytes.
This operator is equivalent to executing the following PostScript emulation sequence:
returns a boolean with the same value as the RealFormat system parameter. It indicates the printer microprocessor native real number representation. A query determines if the printer real number representation matches the application real number representation and compensates if necessary.
renames the oldfilename to the newfilename. This operator is in systemdict.

queries the resolution for the current print job. An integer is returned on the stack:
300 300 dpi is set to On
600 600 dpi is set to On
1200 1200 dpi is set to On
This operator is equivalent to executing the following PostScript emulation sequence:
currentpagedevice /HWResolution get 0 get
queries the Revision system parameter. An integer is returned on the stack to indicate the revision level.
— resolution integer · — revision integer

channel sccbatch baud option
returns the user default settings for serial communication parameters.
channel has the following valid integer values:
If only one serial interface port is available on the printer, both 9 and 25 return the same values. Baud and option values are returned on the stack.
baud returns the value of the Baud menu item.
option returns an 8 bit value as defined in the following illustration:
Flow Control Parity Data Style Stop Bits
This bit is always set to zero.
01 7 data bits
11 8 data bits
001 DTR/DSR
101 DTR
110 XON/XOFF/DTR
111 XON/XOFF/DTR/DSR

channel sccinteractive baud options
provided for parsing compatibility purposes. A value of 0 is returned.
setcoverpage
specifies a cover page for a fax job. The default value is false.
The boolean values indicate:
true the current page that is processing is moved to the first page of the current fax job
false the current page that is processing is unaffected
job manualfeed wait setdefaulttimeouts —
changes the values for all timeouts. Valid values are:
15...65355 seconds
ManualFeedTimeout page device parameter
1...65355 seconds
15...65355 seconds

is parsed and discarded. A boolean value is required.
changes the user default setting of the Jam Recovery menu item. The changes are not effective until the end of the print job.
The boolean values indicate:
true reprint jammed page (Jam Recovery is set to On)
false do not reprint jammed page (Jam Recovery is set to Off or Auto [model dependent])
This operator is equivalent to executing the following PostScript emulation sequence:
%Go into exitserver or startjob context > setpagedevice
sets the system parameter DoPrintErrors to the value of boolean. It also indicates the current value of the Print PS Error printer setting. The DoPrintErrors system parameter must be present for the setdoprinterrors operator to be present.
The boolean values indicate:
true Print PS Error is set to On
false Print PS Error is set to Off
boolean setdoidlefonts — · boolean setdojamrecovery — · boolean setdoprinterrors

changes the PQET setting for the next page through the end of the print job.
The integer values allowed are:
0 turn PQET Off
1 turn PQET On
2 turn PQET On
3 turn PQET On
4 turn PQET On
The value you select for PQET returns to the user default setting when the print job is finished.
This operator is equivalent to executing the following PostScript emulation sequence:
> setpagedevice
sets the DoStartPage system parameter to the value of boolean. The DoStartPage system parameter must be present for the setdostartpage operator to be present. For more information, see “DoStartPage” on page 4-81.
integer setdoret — · boolean setdostartpage

modifies the value of the StartupMode system parameter.
true StartupMode set to 1
false StartupMode set to 0 (default)
sets the value of the Duplex page device parameter for the current print job.
true sets printing mode to duplex
false sets printing mode to simplex At the start of the next print job, the value is reset to the user default setting.
This operator is equivalent to executing the following PostScript emulation sequence:
> setpagedevice
boolean setdosysstart — · boolean setduplexmode —

changes the setting that indicates whether the printer waits for the last page of a job to print before returning a Ctrl-D to the host computer.
The boolean values indicate:
true printer waits for the last page of the job to print
false printer does not wait for the last page of the job to print
sets the EthernetAddress parameter in the EtherTalk communication parameter set. The EthernetAddress parameter is the Ethernet address of the Ethernet internal print server (also called an internal network adapter or INA). The string value can be any string up to 17 characters.
sets whether the extension should be automatically added to any filename.
true adds the extension
false does not add the extension
The default setting is true.
See “Filename Extensions” on page 6-10.
boolean setenginesync — · string setethernetaddress · boolean setfilenameextend

moves the read pointer in an open file to the new specified file position. This is defined as the number of bytes from the start of the file. The next read operation starts at the new file position. This operator is in systemdict.
is parsed and discarded. In addition, one integer is removed from the stack. It supports compatibility with the IBM LaserPrinters 4019, 4029, and 4039.
mark... setildefonts —
supports compatibility with the IBM LaserPrinters 4019, 4029, and 4039. It is parsed and pulls items from the stack until a mark is reached.
See page 4-17.
file position setfileposition · integer sethardwareiomode —

changes the value of the JobTimeout user parameter for the next page through the end of the print job. Valid integers are:
15...65355 seconds
The value returns to the JobTimeout system parameter setting at the end of the print job.
This operator is equivalent to executing the following PostScript emulation sequence:
setuserparams
changes the current job’s setting of manualduplexmode. Valid int values are:
0 no manual duplexing
1 printing the first sides of the job
2 printing the second sides of the job.
When printing second sides of the job is specified, a load manual duplex side 2 operator intervention condition will occur after the last page of the first sides is printed, and prior to the first page of the second sides being printed. While printing the second sides the printer’s available paper sources are restricted to the automatic tray (tray1) and the manual paper feeder for the remainder of the job or until the manual duplex mode value is changed.
See page 4-22.
integer setjobtimeout — · 0 disabled · int setmanualduplexmode

changes the PrinterName system parameter to the value of the string. The string value can be any string up to 32 characters.
This operator is equivalent to executing the following PostScript emulation sequence:
> setsystemparams
changes the user default setting of the PowerSave page device parameter.
The following integers are valid:
0 Power Saver Off
1 to 120 or 1 to 240 (Model specific) Number of minutes elapsed after last page prints before Power Saver is invoked.
Any changes made by this operator are not active until the end of the print job.
This operator is equivalent to executing the following PostScript emulation sequence:
%Go into exitserver or startjob context > setpagedevice
string setprintername — · integer setquiet —

changes the resolution for the current print job and discards unprinted data. Refer to your printer user documentation for a list of supported resolutions. The following integers are valid:
300 300 dpi is set to On 600 600 dpi is set to On
1200 1200 dpi is set to On
This operator is equivalent to executing the following PostScript emulation sequence:
> setpagedevice
where xres = yres.
integer integer integer setsccbatch —
supports compatibility with the IBM LaserPrinters 4019, 4029, and 4039. It is parsed, and three integers are removed from the stack and discarded.
integer setresolution —

channel baud options setsccinteractive
supports compatibility with the IBM LaserPrinters 4019, 4029, and 4039. It is parsed, and three integers are removed from the stack and discarded.
supports compatibility with the IBM LaserPrinters 4019, 4029, and 4039. It is parsed, and an integer is removed from the stack and discarded.
This command validates that the integer value provided is an Adobe-supported value of 0, 1, 2, 3, 4, 5, or 100, and then discards the operator and value.
sets the value of the Tumble page device parameter for the current print job.
true sets the tumble setting to short-edge binding (back side of the duplexed page prints upside down in relation to the front side)
false sets the tumble setting to long-edge binding (back side of the duplexed page prints in the same orientation as the front) (default)
No error is generated if a duplex unit is not installed.
This operator is equivalent to executing the following PostScript emulation sequence:
> setpagedevice
integer setsoftwareiomode — · boolean settumble —

removes an integer from the stack and discards it.
supports compatibility with the IBM LaserPrinters 4019, 4029, and 4039. It is parsed and returns a 0 (zero, Binary Mode Off) on the stack.
Software IO mode defines the data stream you are using.
returns the current value of the Tumble page device parameter.
true the back side of the duplexed page prints upside down in relation to the front side (short-edge binding)
false the back side of the duplexed page prints in the same orientation as the front side (long-edge binding) (default)
This operator is equivalent to executing the following PostScript emulation sequence:

returns a 0 (zero) on the stack.
queries the current value for the WaitTimeout user parameter. An integer is returned on the stack:
15...65355 seconds
This operator is equivalent to executing the following PostScript emulation sequence:

Page Device Parameters
In addition to the page device parameters described in Section 4.11 of the PostScript Language Reference Manual (Third Edition) by Adobe Systems, Inc., the following page device parameters are used by setpagedevice and currentpagedevice. Certain parameters, such as Policies, Priority, and ManualFeed are listed here since more information about the parameters is given in Table 4-14 than in the PostScript Language Reference Manual (Third Edition) by Adobe Systems, Inc.
To determine which parameters and default values your printer supports, see Table C-2 on page C-4.
BeginPage procedure Executes at the beginning of each page and returns an integer which indicates how many times showpage has been invoked.
Collate boolean Indicates if the printer is set to collate multi-copy print jobs.
If a print job consists of three pages and two copies are requested, then the collated output is 1, 2, 3, 1, 2, 3. The non-collated output is 1, 1, 2, 2, 3, 3.
DeferredMediaSelection boolean Determines if the printer uses the printer’s own internal algorithms or Adobe PostScript algorithms to select print media. The following values are supported:
True Uses the printer’s algorithms False Uses Adobe PostScript algorithms (default)
DeviceRenderingInfo dictionary Specifies the following unique printer rendering parameters: Screening, TonerSaver, PictureGrade, ImageEnhancement, PrintDarkness, AutoMediaType, EdgeToEdge, DefaultPoliciesPageSize, SubstituteSize, Type, ColorCorrection, ImageBrightness, ImageContrast, and PrintQuality.
Screening controls which halftone dictionary is installed at the beginning of each print job. The value is set at the start of a job according to the print quality settings selected from the printer operator panel.
The following names are valid:
ColorGrade™ 600 dpi printing PictureGrade 300 dpi, 600 dpi, or 1200 dpi printing with PictureGrade On IET 1200 Image Quality printing or 2400 Print Quality IETImagesOnly 1200 Image Quality printing for images; 600 dpi printing for text and graphics or maps to IET and sets Print Quality to either 1200 Image Quality or 2400 Print Quality IETPictureGrade 1200 Image Quality printing with PictureGrade On None 300 dpi or 600 dpi printing with PictureGrade Off
Key Type Definition

dictionary TonerSaver is a boolean that controls the Toner Saver feature.
True Starts the printer toner saver mechanism False Stops the printer toner saver mechanism
PictureGrade is an integer that provides compatibility with previous Lexmark laser printer drivers. PictureGrade works in conjunction with Screening.
If Screening is set to None or PictureGrade, the values for PictureGrade affect Screening in the following way:
0 Changes Screening to None 1 Changes Screening to PictureGrade
If Screening is set to IET or IETPictureGrade, the values for PictureGrade affect Screening in the following way:
0 Changes Screening to IET 1 Changes Screening to IETPictureGrade
For more information on Screening, see page 4-62.
ImageEnhancement is an integer that provides compatibility with previous Lexmark laser printer drivers. ImageEnhancement works in conjunction with Screening.
If Screening is set to None or IET, the values for ImageEnhancement affect Screening in the following way:
0 Changes Screening to None 1 Changes Screening to IET
If Screening is set to PictureGrade or IETPictureGrade, the values for ImageEnhancement affect Screening in the following way:
0 Changes Screening to PictureGrade 1 Changes Screening to IETPictureGrade
For more information on Screening, see page 4-62.
PrintDarkness specifies the value of the Print Darkness printer setting. Legal values are:
1 Lightest 2 Lighter 3 Normal 4 Darker 5 Darkest
Key Type Definition · DeviceRenderingInfo (continued)

dictionary AutoMediaType is a boolean that controls the MediaType entries in the InputAttributes dictionary in the pagedevice dictionary.
True MediaType entries in the InputAttributes dictionaries cannot be modified by the user. The values are confined to values known by the printer operating system. False MediaType entries in the InputAttributes dictionaries can be modified by the user.
EdgeToEdge is a boolean which determines if there should be an unprintable area on the page.
True Print to the edge of the paper. False Do not print to the edge of the paper (default).
DefaultPoliciesPageSize is an integer which equals the PageSize parameter in the Policies dictionary unless PageSize is set to 23; in that case, DefaultPoliciesPageSize equals the PageSize parameter value before it was set to 23 or equals 0 if the PageSize parameter is initialized to 23. For more information on PageSize, see page 4-72.
SubstituteSize allows for the substitution of A4- and Letter-size print materials, and A3- and 11x17 inch-size print materials for each other when one size is not installed.
The following values are supported:
/Off No size substitution is performed.
/A4-Letter If A4 is requested but not installed and Letter is installed, Letter is substituted for A4. Or, if Letter is requested but not installed and A4 is installed, A4 is substituted for Letter.
/A3-11x17 If A3 is requested but not installed and 11x17 is installed, 11x17 is substituted for A3. Or, if 11x17 is requested but not installed and A3 is installed, A3 is substituted for 11x17.
/All Both size substitutions are permitted. Note: When the size substitution occurs, the page is scaled to the size of the requested print material.
The DefaultPoliciesPageSize value is used as the effective policy when:
Key Type Definition · DeviceRenderingInfo (continued)

dictionary Type is a constant value. To find the value of Type for your printer, see Table C-2 on page C-4.
ColorCorrection is a null, string, or name object that controls the appearance of colors. The value is determined by the user default setting in the Color Correction menu item. The following values are supported:
ImageBrightness is an integer that controls the brightness of images. The following values are supported:
-100 ... 100 0 (default)
ImageContrast is an integer that controls the contrast of images. The following values are supported:
-100 ... 100 0 (default)
PrintQuality is an integer that controls the print quality settings. The following values are supported:
0 Quick Print 1 Normal 2 Presentation 3 1200 Image Q
Duplex boolean Indicates if printed pages are duplexed (printed on both side of the page) or simplexed (printed on one side of the page).
True Print duplex mode False Print simplex mode (default)
EndPage procedure Executes at the end of each printed page to indicate if the contents of raster memory should be printed. EndPage gets two integer arguments through the operand stack: one is a count of the previous showpage executions and the other is the code that indicates the execution condition.
The code is 0 (zero) if it is called from showpage, 1 if it is called from copypage, and 2 if it is called during device deactivation. The procedure must return a boolean value.
ExitJamRecovery boolean Indicates the setting of the Jam Recovery menu item.
True Jam Recovery is set to On. False Jam Recovery is set to Off or Auto (model specific).
HWResolution integer Indicates the resolution of the printer (in pixels per inch) along the x and y dimensions of the device space. x and y are always equal. The following resolutions are supported:
300 dpi 600 dpi 1200 dpi
Key Type Definition · DeviceRenderingInfo (continued) · -null- /Display /Vivid

ImagingBBox array or null Defines a rectangle that lies within the boundaries of the page specified by PageSize. ImagingBBox may be either a value of null or an array of four numbers.
A value of null indicates the bounding box is the largest imageable area possible for a given page size.
InputAttributes dictionary Contains information about the various installed input sources. There is a numeric key, which is a dictionary, for each installed input source.
The numeric keys are:
0 Tray 1 1 Tray 2 2 Envelope feeder 3 Tray 3 4 Multipurpose feeder 5 Tray 4 6 Tray 5
The entries in each input source dictionary describe the media that is currently available in the source. The allowable keys in each source dictionary are:
PageSize MediaColor MediaType (See “AutoMediaType” on page 4-64.) MediaWeight MatchAll InputLocation Read only string which indicates the physical tray corresponding to the source.
Key Type Definition · Input sources · Key Source

dictionary Mode is a key within the InputAttributes dictionary, and its value is a name that determines the mapping of the physical input sources to the input sources listed in InputAttributes. The allowable values are:
/Default Printer’s default source assignment
/Optra Specifies the following ordering used in InputAttributes: 0 - Tray 1 1 - Tray 2 2 - Envelope Feeder 1 or Multipurpose feeder 3 - Tray 3 4 - Multipurpose feeder 5 - Tray 4 6 - Tray 5 7 - Feeder 2
/HPLJFamily1 Specifies the following ordering used by the Hewlett- Packard Company’s printers: 0 - Tray 1 1 - Tray 2 2 - Envelope Feeder 1 or Multipurpose feeder 3 - Multipurpose feeder (see Note) 4 - Tray 3 5 - Tray 4 6 - Tray 5 7 - Feeder 2
Priority is an array of integers that describes the order in which the input sources are searched. The first integer represents the highest priority source and so on. If no array exists or none of the matching sources is in the array, then the priority order is arbitrary.
Install procedure Installs device dependent parameters into the graphics state. This procedure can modify any parameter in the graphics state.
Jog integer Specifies which Offset Pages setting is used. The following values are supported:
0 Offset Pages is disabled. 1 Offset Pages is disabled. 2 Offset Pages is set to Between Jobs. 3 Offset Pages is set to Between Copies.
Offset refers to stacking entire print jobs or copies of the same print job in two separate groups in an output bin.
Key Type Definition · InputAttributes (continued)

ManualFeed boolean Indicates if the current (or active) source is a manual source. The following values are supported:
True Manual feed False Automatic feed
If ManualFeed is set to True, and a change is made to PageSize, MediaWeight, MediaColor, or MediaType parameters, no matching occurs. It is assumed that the correct page is fed.
ManualFeedTimeout integer Indicates the amount of time that the printer waits for you to manually load a sheet of paper.
0 infinite wait or no timeout
If the timeout expires, a timeout error is generated.
This is initialized at the start of each PostScript emulation job to the value of the Feed Timeout menu item value.
MediaColor string name or null
Specifies the color of the current media.
MediaPosition integer Specifies the tray to select, if possible, whether it is the best match or not. Policies may be consulted to determine the selection. For example, assume there is legal-size paper in Tray 1 and letter-size paper in all the other trays, and the Policy for the PageSize page device parameter is 1. The command
> setpagedevice
selects Tray 2 even though Tray 1 is a perfect match, because the PageSize Policy of 1 allows the PageSize to be ignored.
MediaType string name or null
Indicates the type of the current media. The value of the string is arbitrary and may describe any attribute not already defined by size, color, or weight.
MediaWeight integer or null
Specifies the weight of the current media in g/m2. The value is either null or a number.
NumCopies integer or null
Specifies the number of copies of each page that should be printed. If the value is null, the current value of #copies determines the number of copies to print.
Nup boolean Determines if Nup is On or Off. Use the N-up function to print multiple page images on a single page, where the value of N refers to the number of pages. For example, 2-Up means two page images are printed on one page.
True Nup is On and the NupDetails parameters are active. False Nup is Off.
For some printers, the value of Nup is set through the Multipage Printing menu item. For more information about multipage printing (N-up), refer to your printer user documentation.
Key Type Definition

NupDetails dictionary Describes the specific actions performed when the N-up function is active.
Rows is an integer that specifies the number of rows to print on a portrait-oriented page.
Columns is an integer that specifies the number of columns to print on a portrait- oriented page.
Rows and Columns are limited to these values:
2 1 3 1 2 2 3 2 3 3 4 3 4 4
Orientation specifies the orientation of the individual N-up pages on the printed page. Supported values are:
0 Portrait 1 Landscape
Orientation determines the positioning of multiple page images on pages printed using NupDetails. You may choose one of four different orders. The positioning of page images depends on whether they are sent to the printer as portrait or landscape images. The following examples show the result of using each setting on a 2-row, 2-column page:
Portrait Landscape Reverse Vertical Portrait Landscape Reverse Horizontal

dictionary Border specifies the type of border to draw around the individual Nup pages. Supported values are:
0 No border 1 A solid black line
Order is an integer that specifies how the Nup pages are placed on the printed page. Supported values are as follows, with first the value, the orientation, and the description:
0 H The first page is placed at the upper left corner of the printed page and subsequent pages are placed across and then down. 1 V The first page is placed at the upper left corner of the printed page and subsequent pages are placed down and then across. 2 RH The first page is placed at the upper right corner of the printed page
and subsequent pages are placed across and then down. 3 RV The first page is placed at the upper right corner of the printed page
and subsequent pages are placed down and then across.
Type is a constant value. To find the value of Type for your printer, see Table C-2 on page C-4.
LandscapeOverride is a boolean which specifies the orientation of N-up pages. Supported values are:
False Orientation is specified by the PageSize parameter. True Orientation is assumed to be Landscape regardless of the orientation specified by the PageSize parameter. Note: The PostScript emulation interpreter has to know the orientation of N-up pages to position the pages correctly on a hostpage. However, during the translation process, many landscape pages are created in portrait orientation by using the PageSize parameter. Then, the page is rotated to create the appearance of landscape orientation. When this happens, the PostScript emulation interpreter cannot place the N-up page correctly on the hostpage unless the PageSize parameter is set correctly.
Key Type Definition · NupDetails (continued)

OutputAttributes dictionary Contains information about the output bin targets. There is a numeric key, which is a dictionary, for each installed output bin. OutputType and OutputLocation are the allowable keys in each output dictionary. OutputType is used in the search algorithm to determine which output bin is used as the exit path.
The numeric keys are:
0 Standard Output Bin or Top Output Bin 1 Optional Output Bin 1 or Rear Output Bin 2 Optional Output Bin 2 3 Optional Output Bin 3 4 Optional Output Bin 4 5 Optional Output Bin 5 6 Optional Output Bin 6 7 Optional Output Bin 7 8 Optional Output Bin 8 9 Optional Output Bin 9 10 Optional Output Bin 10
OutputType fields can be assigned strings to specify the output destination.
For example:
> >> setpagedevice
> >> setpagedevice
For more information, see “OutputType” on page 4-71.
OutputLocation key is a read-only string that represents the name of the associated destination.
The OutputAttributes dictionary contains a Priority Array. If an OutputType string does not match, the priority array is searched in order for a valid output bin.
The initial value of the priority array is set at the beginning of a job and is equal to the value of the menu item for OutputBin. The array can be changed using this setpagedevice operator:
>> setpagedevice
This command gives the Optional Output Bin 1 (1) a higher priority than the Standard Bin (0). Once the command is issued, if no match is found for the OutputType string, the paper exits into the standard output bin.
OutputPage boolean Specifies if pages are actually printed. Supported values are:
True Job is processed as usual (default). False No page is printed, but all other job processing occurs.
OutputType string Specifies the output bin destination for the current page. If the destination is not null, setpagedevice compares it with the OutputType values in the OutputAttributes dictionary during the search algorithm. If a match is found, this output bin is the target output for the current page.
PageDeviceName string name or null
Assigns or names a page device by using a string parameter. This is used by the findcolorrendering operator.
Key Type Definition

PageSize array Specifies the size [width height] of the current page in 1/72 inch units. A value of [0 0] is assumed to be the lower left corner of the physical page and [width height] is the upper right corner.
Policies dictionary Uses entries to describe the actions to perform when a particular function cannot be completed. The entries are as follows:
PageSize is an integer that specifies what recovery action to use when PageSize cannot be matched with any available media (paper, envelope, or other print materials). The actions are:
0 Generate a configurationerror. (default) 1 Ignore the requested PageSize. 2 Interact with a human operator or print manager. 3 Select the next larger or smaller available media and adjust the page to fit. 4 Select the next larger available media and adjust the page to fit. 5 Select the next larger or smaller available media, but do not adjust the page. 6 Select the next larger available media, but do not adjust the page. 7 Disable media selection. Implement the requested PageSize on the previously selected media without making adjustments. The way the image is positioned on the media is printer-dependent and may result in part of the image being clipped. 23 If the SubstituteSize parameter from the DeviceRenderingInfo dictionary is set to Off, the effective policy executed is the value of the DefaultPageSizePolicy key in the DeviceRenderingInfo dictionary. If the SubstituteSize parameter from the DeviceRenderingInfo dictionary is set to a value other than Off and an installed source has installed media which may be substituted for the requested media, the effective policy executed is 3. If the SubstituteSize parameter from the DeviceRenderingInfo dictionary is set to a value other than Off and a media substitution cannot be made, the effective policy executed is the value of the DefaultPageSizePolicy key in the DeviceRenderingInfo dictionary.
PolicyNotFound is an integer that specifies which recovery action to use when a requested feature other than PageSize cannot be matched with any key in the Policies dictionary.
The actions are: 0 Generate a configurationerror. 1 Ignore the requested feature (default). 2 Interact with a person or print manager.
PolicyReport is a procedure that is called when a successful setpagedevice is finished. The procedure consults policies to process unsatisfied feature requests if needed. Default value is {pop}.
PostRenderingEnhance boolean Always True to indicate that PostRenderingEnhanceDetails is enabled.
Key Type Definition

dictionary Describes enhancements that are made to the output after the page has been held in memory.
REValue is an integer that specifies the current value of the PQET menu item. Supported values are:
0 PQET is Off. 1 to 4 PQET is On (default is 1).
Type is a constant value. To find the value of Type for your printer, see “PostRenderingEnhanceDetails” on page C-7.
PowerSave integer A value of 1 - 120 or 1 - 240 (model specific) indicates the number of minutes that elapses after the last page prints and before the Power Saver feature is invoked. A value of 0 (zero) indicates the Power Saver feature is turned Off on some printer models.
This value is initialized at the start of each PostScript emulation job to the value of the Power Saver menu item.
ProcessColorModel name or string
Specifies the color model to use for rendering process colors in the printer. Supported values are:
DeviceGray DeviceRGB DeviceCMYK DeviceCMY
Punch integer Requests holes to be punched in the output page. The format for setting the Punch key is:
where n is one of the following values:
0 Do not punch holes in the output page. 3 Punch holes in the output page.
SlipSheet integer Specifies where blank separator sheets should be inserted in the output. Supported values are:
0 Do not insert separator sheets. 1 Insert separator sheet at device deactivation. 2 Insert separator sheet at end of the print job. 3 Insert separator sheet at the end of each set in a multicopy job.
If Collate is set to True, a set consists of one copy of each page of the document. For example, if a print job is five pages long, a set is one copy of pages one to five. If Collate is set to False, a set is all the copies of a single page of the job. For example, if a print job is three copies of a five page job, a set is three copies of the first page. 4 Insert separator sheet after each showpage or copypage.
Key Type Definition · PostRenderingEnhance Details · setpagedevice

SlipSheetDetails dictionary Specifies the following two unique separator sheet parameters: SlipSheetSource and Type.
SlipSheetSource is an integer type parameter which identifies the source used for separator sheets. Supported values are:
Null Use current source (default) 0 Tray 1 1 Tray 2 2 Envelope Feeder 3 Tray 3 4 Multipurpose feeder 5 Tray 4 6 Tray 5
The key is found in the DeviceRenderingInfo dictionary within pagedevice. It can be altered using a setpagedevice operator.
/SlipSheetDetails > >> setpagedevice
Type is a constant value. To find the value of Type for your printer, see Table C-2 on page C-4.
Staple integer Specifies whether to staple the current print job.
Supported values are:
0 Do not staple print job. 1 Staple each set in the front position. 2 Staple each set in the rear position. 3 Staple each set according to the Auto setting. 4 Staple each set in the dual position.
The format for setting the Staple key is:
TraySwitch boolean Indicates tray linking is always active. When the media in one input source is depleted, other input sources are searched to determine if the same media can be found in another source. If another source is found, the alternate source is selected. The media in both input sources must be the same size and type for tray linking to occur.
Key Type Definition · setpagedevice

Tumble boolean Indicates the orientation of the second side of a duplexed page with respect to the first side. Supported values are:
True Causes pages to print as if they are to be bound across the top of the page (image is rotated 180° on the back side of the page) False Causes pages to print as if they are to be side bound (as in a book)
UniversalDetails dictionary Controls the variable Universal paper size feature. The entries are as follows:
Type is a constant value. To find the value of Type for your printer, see Table C-2 on page C-4.
PageSize is an array of two numbers (real or integer) that defines the x and y values (in points) for Universal.
Orientation is an integer that defines how the Universal paper will be fed through the printer. Supported values are:
0 Paper is fed short edge first. 1 Paper is fed long edge first.
Prompt defines a string to be displayed on the operator panel when the printer prompts a user to load Universal.
Key Type Definition

Interpreter Parameters
This section describes the PostScript emulation interpreter parameters. There are three types of interpreter parameters:
To determine which parameters your printer supports, see Appendix C: “PostScript Support” on page C-1.
The following user parameters are used by setuserparams and currentuserparams.
If a value is requested that is not within the range for the requested parameter, the minimum (or maximum) value is used.
If a setuserparams value does not match the type of the specified parameter, a typecheck error occurs. If a parameter is not supported by the printer, it is ignored. An attempt to change the value of a read-only parameter has no effect on the parameter.
To determine which parameters your printer supports, see Table C-3 on page C-8.
AccurateScreens boolean Controls whether the accurate screen algorithm is used during subsequent executions of the setscreen and setcolorscreen operators.
CollatedCopies integer Requests the number of collated copies to print for the job. The CollatedCopies parameter must be set before the first page of the job has been sent.
If CollatedCopies is set to zero, the parameter has no effect on the job. If CollatedCopies is set to a number other than zero, the value of #copies and of the NumCopies and Collate pagedevice parameters are ignored for the job.
Legal values: Any integer between 0 and 999, inclusive.
Key Type Definition

HalftoneMode integer Affects the results of subsequent halftone setting operators such as setscreen, setcolorscreen, and sethalftone. The HalftoneMode parameter has no effect on the current halftone.
Legal values:
0 Normal mode of operation. The operators setscreen, setcolorscreen, and sethalftone are not affected. 1 Execution of setscreen, setcolorscreen, or sethalftone causes a default screen to be used rather than the screen given by the job. The default screen depends on the current resolution and parameters in the DeviceRenderingInfo dictionary in the pagedevice dictionary that is in affect at the time the halftone operator is executed. 2 Not supported. HalftoneMode is set to 1.
IdiomRegnition boolean Legal values:
True Procedure substitution is enabled during execution of the bind operator. False Idiom recognition is disabled.
JobName string Name of the current job for status responses.
Legal values: Any alphanumeric characters in the ASCII printable range (X'20' through X'FE') excluding the characters ; and ]. Maximum length is 80 characters (characters beyond 80 characters are truncated).
JobTimeout integer Number of seconds a print job executes before it is terminated and a PostScript emulation timeout error is generated.
Set to 0 to disable job timeout.
JobTimeout is initialized to the value of the JobTimeout system parameter at the beginning of each job.
Legal value: Any non-negative integer.
MaxDictStack integer Maximum elements in a dictionary stack.
Legal value: Any integer between 40 and 255, inclusive.
MaxExecStack integer Maximum elements in the execution stack.
Legal value: Any integer greater than or equal to 75.
MaxFontItem integer Maximum number of bytes occupied by the pixel array of a single character in the font cache.
There is an upper limit dependent on the MaxFontCache system parameter and the amount of printer memory.
Legal values: Any non-negative integer.
MaxFormItem integer Maximum number of bytes occupied by a single cached form.
Legal value: Any integer between zero and half of RamSize.
MaxLocalVM integer Maximum bytes occupied by values in local VM.
Legal value: Any integer greater than or equal to 76800 or the amount of local VM currently in use plus a small margin.
Key Type Definition

MaxOpStack integer Maximum elements in the operand stack.
Legal value: Any integer greater than or equal to 75.
MaxPatternItem integer Maximum bytes occupied by a single cached pattern.
Legal value: Any integer between zero and half of RamSize.
MaxScreenItem integer Maximum bytes occupied by a single halftone screen.
Legal value: Any non-negative integer.
MaxSuperScreen integer Establishes an upper limit for the number of pixels in the supercell. Supercells affect Type 1 and Type 2 halftones.
If MaxSuperScreen is set to zero, the use of supercells is prevented.
Legal value: Any integer between zero and half of RamSize.
MaxUPathItem integer Maximum bytes occupied by a single user path.
Legal value: Any integer between zero and half of RamSize.
MinFontCompress integer (Read-only) This value is always the value of MAXINTEGER.
PageCount integer (Read-only) This value is a running sum of the number of pages submitted by the PostScript interpreter to the print engine for printing.
This parameter is not valid for tracking pages between jobs.
UseOldcopypage boolean Legal values:
True Indicates the copypage command is processed as defined in the PostScript Level 2 description. False Indicates the copypage command is processed as defined in the PostScript 3 description.
VMReclaim integer Legal values:
0 Enables automatic garbage collection -1 Disables automatic garbage collection for local Virtual Memory (VM) -2 Disables automatic garbage collection for both local and global VM
VMThreshold integer Frequency of automatic garbage collection, which occurs when the specified number of bytes have been allocated since the previous collection.
Legal value: Any integer from 8192 to 500000, inclusive.
WaitTimeout integer Number of seconds the interpreter waits to receive additional characters from the host before it terminates the current print job by executing a PostScript emulation timeout error.
A value of 0 indicates an infinite timeout. WaitTimeout is initialized to the value of the WaitTimeout system parameter at the beginning of each print job.
Legal value: Any non-negative integer.
Key Type Definition

System Parameters
The setsystemparams operator sets the values of the specified system parameters. This operator requires a password if one is set. The currentsystemparams operator returns a dictionary of the current values of the system parameters.
Values supplied to setsystemparams that are outside the range or limits for the specified integer parameter do not cause rangecheck or limitcheck errors. An appropriate value is used. For example, if you set JobTimeout to 14, it is actually set to 15, and no error is generated. The exceptions are noted in Table 4-16.
Values supplied to setsystemparams that do not match the type of the specified parameter cause typecheck errors. Parameters that are not supported by the printer are ignored. An attempt to change the value of a read-only parameter has no effect on the parameter. Write-only parameters are not returned by currentsystemparams.
To determine which parameters your printer supports, see Table C-4 on page C-9.
BuildTime integer (Read-only) Timestamp identifying the specific build of the PostScript emulation interpreter.
ByteOrder boolean (Read-only) Native (preferred) order of multiple-byte numbers in binary encoded tokens.
False high-order first True low-order first
CurDisplayList integer (Read-only) This value is always zero.
CurFontCache integer (Read-only) Bytes currently occupied by the font cache.
CurFormCache integer (Read-only) Bytes currently occupied by the form cache.
1 These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 2016. 2 These parameters are available with the Adobe PostScript Language Supplement 3010. 3 These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 3010.
Key Type Definition

CurInputDevice string (Read-only) The name of the communications device
corresponding to the current input file for the PostScript emulation program which is currently executing. Possible values are:
%LocalTalkA% %TokenTalkD% %LocalTalkB% %LexLinkB% %LocalTalkC% %LexLinkC% %LocalTalkD% %LexLinkD% %SerialA% %PrintServerB% %SerialB% %PrintServerC% %SerialC% %PrintServerD% %SerialD% %RemotePrinterB% %ParallelA% %RemotePrinterC% %ParallelB% %RemotePrinterD% %ParallelC% %AppSocketB% %ParallelD% %AppSocketC% %IR_A% %AppSocketD% %IR_B% %LPR_B% %IR_C% %LPR_C% %IR_D% %LPR_D% %EtherTalkB% %UnknownDevice% %EtherTalkC% %USB_A% %EtherTalkD% %USB_B% %TokenTalkB% %USB_C% %TokenTalkC% %USB_D%
CurOutlineCache integer (Read-only) This value is always zero.
CurOutputDevice string (Read-only) The name of the communications device corresponding to the current output file for the PostScript emulation program which is currently executing. This string is the same as CurInputDevice.
CurPatternCache integer (Read-only) Bytes currently occupied by the pattern cache.
CurScreenStorage integer (Read-only) This value is always zero.
CurSourceList integer (Read-only) This value is always zero.
CurUPathCache integer (Read-only) Bytes currently occupied by the user path cache.
DisableFastProcs integer This bit field allows precompiled PostScript procedures to be selectively disabled. These precompiled procedures speed the execution time of some application-generated print jobs by substituting PostScript procedures in the job’s ProcSet with fast functions that are built into the printer firmware.
1 These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 2016. 2 These parameters are available with the Adobe PostScript Language Supplement 3010. 3 These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 3010.
Key Type Definition

DoPrintErrors boolean Specifies whether to print an error page using a built-in error handler when a PostScript emulation error occurs.
True Print PS Error user default value is set to On. False Print PS Error user default value is set to Off.
DoStartPage boolean (Read only) Always returns False.
EnableExtraFonts1 boolean True All 75 resident fonts are enabled. False Original 39 PostScript fonts are available. Note: Changes to this parameter take effect when PostScript is restarted.
EngineBoot1 string (Read-only) Specifies the version of the boot code.
EngineCode1 string (Read-only) Specifies the version of the engine code.
EngineSpeed1 integer (Read-only) Maximum speed of the print engine in pages per minute.
EnvironmentSave2 boolean Indicates or modifies the Resource Save user default value.
True Resource Save user default value is set to On. False Resource Save user default value is set to Off. Note: When a job changes this parameter from False to True, all interpreter tasks such as PostScript and PCL are terminated and restarted at the end of the current job.
FactoryDefaults boolean If set to True and the printer is then immediately powered off, all non-volatile parameters revert to factory default values at the next power-on. The print job that sets FactoryDefaults to True must be the last job executed before power-off; otherwise, the request is ignored.
FatalErrorAddress integer The address at which a fatal system software error occurred. It is stored in this parameter before execution is stopped. It is also transmitted to the host over the communications channel.
FontResourceDir string Specifies the location in the file system for font resource files.
FontVersion1 string (Read-only) The version of the font read-only memory (ROM).
GenericResourceDir string Specifies the location in the file system for resource files.
GenericResourcePathSep string Concatenated to the GenericResourceDir and the category name. It is followed by the resource name to get the external location of the resource.
Example: If GenericResourceDir and GenericResourcePathSep were (Resource/) and (/), respectively, the LexmarkLogo resource of the Pattern category would be in Resource/Pattern/LexmarkLogo.
1 These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 2016. 2 These parameters are available with the Adobe PostScript Language Supplement 3010. 3 These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 3010.
Key Type Definition

InstalledRam integer (Read-only) Indicated, in bytes, the total amount of installed printer memory (RAM) in the system.
JobTimeout integer The value in seconds to which the user parameter JobTimeout is initialized at the beginning of each print job. If you set the system parameter JobTimeout to a negative value, it is ignored and the previous setting of JobTimeout is used. A value of 0 (zero) indicates that the timeout is infinite. If you set a number between 1 and 14, 15 is set.
languagelevel integer The value of languagelevel integer in systemdict always matches the value of this system parameter. If set to 2, the printer will behave as though /UseOldcopypage and /UseOldfonts are both true (regardless of their actual values). The latter two parameters will return their actual values when queried.
MaxDisplayAndSourceList2 integer (Read-only) This value is always the same value as InstalledRam.
MaxDisplayList integer (Read-only) See Table C-4 on page C-9 for the default value of your printer.
MaxFontCache integer (Read-only) See Table C-4 on page C-9 for the default value of your printer.
MaxFormCache integer Maximum bytes occupied by the form cache.
Legal value: Any non-negative integer.
MaxImageBuffer integer (Read-only) See Table C-4 on page C-9 for the default value of your printer.
MaxOutlineCache integer (Read-only) See Table C-4 on page C-9 for the default value of your printer.
MaxPatternCache integer Maximum bytes occupied by the pattern cache.
Legal value: Any non-negative integer.
MaxPermanentVM2 integer (Read-only) See Table C-4 on page C-9 for the default value of your printer.
MaxRasterMemory integer (Read-only) See Table C-4 on page C-9 for the default value of your printer.
MaxScreenStorage integer (Read-only) See Table C-4 on page C-9 for the default value of your printer.
1 These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 2016. 2 These parameters are available with the Adobe PostScript Language Supplement 3010. 3 These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 3010.
Key Type Definition

MaxSourceList integer (Read-only) See Table C-4 on page C-9 for the default value of your printer.
MaxUPathCache integer Maximum bytes occupied by the user path cache.
Legal value: Any non-negative integer.
PageCount integer (Read-only) Total number of pages that have been printed.
PanelCode1 string (Read-only) Version of the operator panel code.
PrinterCode1 string (Read-only) Firmware version of the printer controller card.
PrinterName string Initialized from the printer name stored in NVRAM (the default name of the printer). If this parameter is set to a zero length string, the PrinterName is set to the value of the product string in statusdict.
Legal value: Any string of 32 or fewer non-null characters.
RamSize integer (Read-only) Total amount of memory (in bytes) installed in the printer.
RealFormat string (Read-only) Preferred representation for real numbers in binary encoded tokens.
Revision integer (Read-only) The current revision level of the machine- dependent portion of PostScript emulation.
SearchBuiltinFontsFirst1 boolean Controls the device search order the interpreter uses to locate fonts.
SerialNumber1 string (Read-only) Serial number of your printer.
StartJobPassword string (Write-only) Controls the ability of the startjob operator to alter initial Virtual Memory (VM).
Legal value: Any integer or string of 32 or fewer non-null characters. An integer is converted to a string.
StartupMode integer Controls the system start file (Sys/Start) during PostScript emulation initialization. Also, controls the job start file (Job/ Start) before each print job.
0 Disable use of Sys/Start file and Job/Start file. 1 Sys/Start file executes (if present on disk or flash). 10 Job/Start file executes before each user job. 11 Both files run (a combination of 1 and 10).
Legal Values: 0
StaticRamSize1 integer (Read-only) Amount of static memory (in bytes) on the controller board.
1 These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 2016. 2 These parameters are available with the Adobe PostScript Language Supplement 3010. 3 These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 3010.
Key Type Definition

SystemParamsPassword string (Write-only) Controls the ability of setsystemparams to change the values of system parameters and setdevparams to change the values of device parameters.
Legal value: Any integer or string of 32 or fewer non-null characters. An integer is converted to a string.
UseOldcopypage3 boolean True indicates the copypage command is processed as defined in PostScript Level 2 description. False indicates the copypage command is processed as defined in PostScript 3 description.
UseOldFonts3 boolean True redefines the following PostScript resident fonts to match the character designs and metrics defined in PostScript Level 2. The font names in parentheses are the equivalent PostScript 3 font names for the associated PostScript Level 2 names.
Antique Olive (Antique Olive Roman) Antique Olive Bold Antique Olive Italic Letter Gothic Letter Gothic Bold Letter Gothic Italic (Letter Gothic Slanted) Marigold Univers Bold
False restores the font compatibility to PostScript 3.
ValidNV boolean (Read-only) Indicates if non-volatile memory is currently used to store persistent parameters. If this memory is found defective during system initialization, factory defaults are used. If further testing reveals this memory is defective, it is not used and ValidNV is False. Otherwise, ValidNV is True.
WaitTimeout integer The value, in seconds, to which the user parameter WaitTimeout is initialized at the beginning of each print job. Negative values are ignored and the previous setting is used. A value of zero indicates an infinite timeout. If you select a number between 1 and 14, 15 is set.
1 These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 2016. 2 These parameters are available with the Adobe PostScript Language Supplement 3010. 3 These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 3010.
Key Type Definition

Device Parameters
The currentdevparams operator returns a dictionary of the current values of the system parameters.
The setdevparams operator sets the values of the specified device parameters.
– %SerialA% – %SerialB% – %SerialC% – %SerialD%
For some printers, no “A” channel exists. If %Serial% is specified, it refers to the channel where the print job is sent.
For additional information on flash memory and disk, see Chapter 6: “Flash Memory and Disk” on page 6-1.
To determine which devices your printer supports, see Table C-5 on page C-11.
To determine which device parameters your printer supports, see Table C-6 on page C-13.

Device Parameters for the Communication Device %Parallel%, %ParallelA%, %ParallelB%, %ParallelC%, %ParallelD%
(%Parallel_NV% and %Parallel_Pending% contain the same parameters)
DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are:
True An end-of-file message is not sent until the current job and all preceding jobs finish printing. False An end-of-file message is sent as soon as a job finishes executing in the interpreter, whether or not that job has finished printing.
This value is set independently for each port.
Supported values are:
Filtering name Indicates if the input needs further filtering before the data can be correctly processed. Supported values are:
Handshake integer (Read-only) Always returns a value of 2.
HasNames boolean (Read-only) Always returns False.
Supported values are:
PostScript AutoSelect PCL PPDS
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed False Data is lost
PCLSmartSwitch boolean Supported values are:
True PCL SmartSwitch is set to On. False PCL SmartSwitch is set to Off.
For more information, see “Using SmartSwitch” on page 2-1.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3 Option Slot 4

PSSmartSwitch boolean Supported values are:
True PS SmartSwitch is set to On. False PS SmartSwitch is set to Off.
For more information, see “Using SmartSwitch” on page 4-1.
Type name (Read-only) Always returns the value of /Communications.
Device Parameters for the Communication Device %Serial%, %SerialA%, %SerialB%, %SerialC%, %SerialD%
(%Serial_NV% and %Serial_Pending% contain the same parameters)
Baud integer Returns the value of the Baud menu item.
CheckParity boolean (Read-only) Designates whether parity checking is done on the incoming data. Supported values are:
True Parity menu item set to Even or Odd. False Parity menu item set to None or Ignore.
DataBits integer Returns the value of the Data Bits menu item.
DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are:
True An end-of-file message is not sent until the current job and all preceding jobs finish printing. False An end-of-file message is sent as soon as a job finishes executing in the interpreter, whether or not that job has finished printing.
This value is set independently for each port.
Supported values are:
Filtering name Indicates if the input needs further filtering before the data can be correctly processed. Supported values are:
FlowControl name Designates the serial flow control method between the host computer and the device. Returns a value corresponding to the Serial Protocol menu item. Supported values are:
Dtr DtrDsr XonXoff XonXoffDtr XonXoffDtrDsr
HasNames boolean (Read-only) Always returns False.
HonorDSR boolean Serial - Honor DSR. Supported values are:
True Honor DSR is set to On. False Honor DSR is set to Off.

Supported values are:
PostScript AutoSelect PCL PPDS
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
Parity name Designates the parity to be used between the host computer and the device. Returns the value of the Parity menu item. Supported values are:
Even Odd None Ignore
If Parity is set to Ignore, CheckParity is set to False and Parity becomes Even.
PCLSmartSwitch boolean Supported values are:
True PCL SmartSwitch is set to On. False PCL SmartSwitch is set to Off.
For more information, see “Using SmartSwitch” on page 2-1.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
PSSmartSwitch boolean Supported values are:
True PS SmartSwitch is set to On. False PS SmartSwitch is set to Off.
For more information, see “Using SmartSwitch” on page 4-1.
RobustXon boolean Supported values are:
True RobustXon is set to On. False RobustXon is set to Off.
SerialMode name Designates the serial communication configuration: RS232C or RS422. Returns the value of the Serial RS-232/RS-422 menu item. Supported values are:
Returns RS232 on a printer that is attached with a cable that does not support RS-422.
Key Type Definition · Interpreter name (Read-only)

Supported values are:
Type name (Read-only) Always returns the value of /Communications.
Device Parameters for the Communication Device %LocalTalk%, %LocalTalkA%, %LocalTalkB%, %LocalTalkC%, %LocalTalkD%
(%LocalTalk_NV% and %LocalTalk_Pending% contain the same parameters)
DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are:
True An end-of-file message is not sent until the current job and all preceding jobs finish printing. False An end-of-file message is sent as soon as a job finishes executing in the interpreter, whether or not that job has finished printing.
This value is set independently for each port.
Supported values are:
Filtering name Indicates if the input needs further filtering before the data can be correctly processed. Supported values are:
HasNames boolean (Read-only) Always returns False.
Supported values are:
PostScript AutoSelect PCL PPDS
LocalTalkType string The “type” of the AppleTalk network entity name. This parameter also sets the Type parameter to the same value. The new value is returned by the appletalktype compatibility operator.
Legal value: Any string of 32 or fewer non-null characters. Default value is LaserWriter.
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.

PCLSmartSwitch boolean Supported values are:
True PCL SmartSwitch is On. False PCL SmartSwitch is Off.
For more information, see “Using SmartSwitch” on page 2-1.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
PSSmartSwitch boolean Supported values are:
True PS SmartSwitch is On. False PS SmartSwitch is Off.
For more information, see “Using SmartSwitch” on page 4-1.
Type name (Read-only) Always returns the value of /Communications.
Device Parameters for the Communication Device %EtherTalk%, %EtherTalkA%, %EtherTalkB%, %EtherTalkC%, %EtherTalkD%
(%EtherTalk_NV% and %EtherTalk_Pending% contain the same parameters)
DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are:
True An end-of-file message is not sent until the current job and all preceding jobs finish printing. False An end-of-file message is sent as soon as a job finishes executing in the interpreter, whether or not that job has finished printing.
This value is set independently for each port.
Supported values are:
EthernetAddress string (Read only) The Ethernet address of the Ethernet internal print server.
Legal value: Any string of 17 or fewer non-null characters.
EtherTalkType string The “type” of the EtherTalk interface entity name. This parameter also sets the LocalTalkType parameter to the same value. The new value is returned by the appletalktype compatibility operator.
Legal value: Any string of 32 or fewer non-null characters. Default value is LaserWriter.
EtherTalkZone string The “zone” of the EtherTalk interface entity name.
EtherTalkZone is read/write only to RAM. There is no NVRAM variable for EtherTalkZone.
Legal value: Any string of 32 or fewer non-null characters.
Key Type Definition · Enabled boolean (Read-only) · True False

Filtering name Indicates if the input needs further filtering before the data can be correctly processed. Supported values are:
HasNames boolean (Read-only) Always returns False.
Supported values are:
PostScript AutoSelect PCL PPDS
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
PCLSmartSwitch boolean Supported values are:
True PCL SmartSwitch is On. False PCL SmartSwitch is Off.
For more information, see “Using SmartSwitch” on page 2-1.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
PSSmartSwitch boolean Supported values are:
True PS SmartSwitch is On. False PS SmartSwitch is Off.
For more information, see “Using SmartSwitch” on page 4-1.
Type name (Read-only) Always returns the value of /Communications.
Device Parameters for the Communication Device %IR%, %IR_A%, %IR_B%, %IR_C%, %IR_D%
(%IR_NV% and %IR_Pending% contain the same parameters)
DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are:
True An end-of-file message is not sent until the current job and all preceding jobs finish printing. False An end-of-file message is sent as soon as a job finishes executing in the interpreter, whether or not that job has finished printing.
This value is set independently for each port.

Supported values are:
Filtering name Indicates if the input needs further filtering before the data can be correctly processed. Supported values are:
HasNames boolean (Read-only) Always returns False.
Supported values are:
PostScript AutoSelect PCL PPDS
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
PCLSmartSwitch boolean Supported values are:
True PCL SmartSwitch is On. False PCL SmartSwitch is Off.
For more information, see “Using SmartSwitch” on page 2-1.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
PSSmartSwitch boolean Supported values are:
True PS SmartSwitch is set to On. False PS SmartSwitch is set to Off.
For more information, see “Using SmartSwitch” on page 4-1.
Type name (Read-only) Always returns the value of /Communications.
Device Parameters for the Communication Device %USB%, %USB_A%, %USB_B%, %USB_C%, %USB_D%
(%USB_NV% and %USB_Pending% contain the same parameters)
DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are:
True An end-of-file message is not sent until the current job and all preceding jobs finish printing. False An end-of-file message is sent as soon as a job finishes executing in the interpreter, whether or not that job has finished printing.

Supported values are:
Filtering name Indicates if the input needs further filtering before the data can be correctly processed. Supported values are:
HasNames boolean (Read-only) Always returns False.
Supported values are:
PostScript AutoSelect PCL PPDS
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
PCLSmartSwitch boolean Supported values are:
True PCL SmartSwitch is On. False PCL SmartSwitch is Off.
For more information, see “Using SmartSwitch” on page 2-1.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1, 2, and 3 (Model specific)
PSSmartSwitch boolean Supported values are:
True PS SmartSwitch is set to On. False PS SmartSwitch is set to Off.
For more information, see “Using SmartSwitch” on page 4-1.
Type name (Read-only) Always returns the value of /Communications.
Device Parameters for the Communication Device %TokenTalk%, %TokenTalkA%, %TokenTalkB%, %TokenTalkC%, %TokenTalkD%
(%TokenTalk_NV% and %TokenTalk_Pending% contain the same parameters)
Bridging name (Read-only) Adaptive

DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are:
True An end-of-file message is not sent until the current job and all preceding jobs finish printing. False An end-of-file message is sent as soon as a job finishes executing in the interpreter, whether or not that job has finished printing.
This value is set independently for each port.
Supported values are:
Filtering name Indicates if the input needs further filtering before the data can be correctly processed. Supported values are:
HasNames boolean (Read-only) Always returns False.
Supported values are:
PostScript AutoSelect PCL PPDS
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
PCLSmartSwitch boolean Supported values are:
True PCL SmartSwitch is On. False PCL SmartSwitch is Off.
For more information, see “Using SmartSwitch” on page 2-1.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
PSSmartSwitch boolean Supported values are:
True PS SmartSwitch is set to On. False PS SmartSwitch is set to Off.
For more information, see “Using SmartSwitch” on page 4-1.

TokenTalkType string Setting this variable does not affect the value of other physical internal print servers.
Type name (Read-only) Always returns the value of /Communications.
Zone string Returns the value identified when the printer makes connection to the network at power on.
Device Parameters for the Communication Device %AppSocket%, %AppSocketA%, %AppSocketB%, %AppSocketC%, %AppSocketD%
(%AppSocket_NV% and %AppSocket_Pending% contain the same parameters)
DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are:
True An end-of-file message is not sent until the current job and all preceding jobs finish printing. False An end-of-file message is sent as soon as a job finishes executing in the interpreter, whether or not that job has finished printing.
This value is set independently for each port.
Supported values are:
Filtering name Indicates if the input needs further filtering before the data can be correctly processed. Supported values are:
HasNames boolean (Read-only) Always returns False.
Supported values are:
PostScript AutoSelect PCL PPDS
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
Type name (Read-only) Always returns the value of /Communications.

Device Parameters for the Communication Device %RemotePrinter%, %RemotePrinterA%, %RemotePrinterB%, %RemotePrinterC%, %RemotePrinterD%
(%RemotePrinter_NV% and %RemotePrinter_Pending% contain the same parameters)
DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are:
True An end-of-file message is not sent until the current job and all preceding jobs finish printing. False An end-of-file message is sent as soon as a job finishes executing in the interpreter, whether or not that job has finished printing.
This value is set independently for each port.
Supported values are:
Filtering name Indicates if the input needs further filtering before the data can be correctly processed. Supported values are:
InterpreterBased None Note: Setting this variable changes the value of the corresponding %PrintServer% device.
HasNames boolean (Read-only) Always returns False.
Supported values are:
PostScript AutoSelect PCL PPDS
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
Type name (Read-only) Always returns the value of /Communications.

Device Parameters for the Communication Device %PrintServer%, %PrintServerA%, %PrintServerB%, %PrintServerC%, %PrintServerD%
(%PrintServer_NV% and %PrintServer_Pending% contain the same parameters)
DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are:
True An end-of-file message is not sent until the current job and all preceding jobs finish printing. False An end-of-file message is sent as soon as a job finishes executing in the interpreter, whether or not that job has finished printing.
This value is set independently for each port.
Supported values are:
Filtering name Indicates if the input needs further filtering before the data can be correctly processed. Supported values are:
InterpreterBased None Note: Setting this variable changes the value of the corresponding %RemotePrinter% device.
HasNames boolean (Read-only) Always returns False.
Supported values are:
PostScript AutoSelect PCL PPDS
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
Type name (Read-only) Always returns the value of /Communications.

Device Parameters for the Communication Device %LPR%, %LPR_A%, %LPR_B%, %LPR_C%, %LPR_D%
(%LPR_NV% and %LPR_Pending% contain the same parameters)
Supported values are:
Filtering name Indicates if the input needs further filtering before the data can be correctly processed. Supported values are:
HasNames boolean (Read-only) Always returns False.
Supported values are:
PostScript AutoSelect PCL PPDS
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
Type name (Read-only) Always returns the value of /Communications.
Device Parameters for the Communication Device %LexLink%, %LexLinkA%, %LexLinkB%, %LexLinkC%, %LexLinkD%
(%LexLink_NV% and %LexLink_Pending% contain the same parameters)
DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are:
True An end-of-file message is not sent until the current job and all preceding jobs finish printing. False An end-of-file message is sent as soon as a job finishes executing in the interpreter, whether or not that job has finished printing.
This value is set independently for each port.
Supported values are:

HasNames boolean (Read-only) Always returns False.
Supported values are:
PostScript AutoSelect PCL PPDS
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
Type name (Read-only) Always returns the value of /Communications.
Device Parameters for the Parameters Device %IP%, %IP_A%, %IP_B%, %IP_C%, %IP_D%
Supported values are:
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
Type name (Read-only) Always returns the value of /Parameters.

Device Parameters for the Parameters Device %EthernetPhysical%, %EthernetPhysicalA%, %EthernetPhysicalB%, %EthernetPhysicalC%, %EthernetPhysicalD%
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
Type name (Read-only) Always returns the value of /Parameters.
Device Parameters for the Parameters Device %TokenRingPhysical%, %TokenRingPhysicalA%, %TokenRingPhysicalB%, %TokenRingPhysicalC%, %TokenRingPhysicalD%
On boolean Designates if the communication channel is On and able to receive and send data. Supported values are:
True Data is sent and processed. False Data is lost.
PortLocation string (Read-only) Designates the physical location of the port related to the parameter set. Supported values are:
Standard Port Option Slot 1 Option Slot 2 Option Slot 3
Speed integer Supported values are:
Type name (Read-only) Always returns the value of /Parameters.
Device Parameters for the Parameters Device %Engine%
BSizeStandard name (Read-only) Value of JIS
Key Type Definition · EthernetAddress string (Read-only) · Address string (Read-only)

Darkness real Print Darkness and Toner Saver Setting
Designates the print darkness and toner saver setting (model specific).
Legal value: Any non-negative real number from 0.0 to 1.0, inclusive.
For queries, the Print Darkness setting is returned as a real value:
Print Darkness Toner Saver Darkness Value Setting Setting Value Returned Lightest On 0.1 Lighter On 0.2 Normal On 0.3 Darker On 0.4 Darkest On 0.5 Lightest Off 0.6 Lighter Off 0.7 Normal Off 0.8 Darker Off 0.9 Darkest Off 1.0
When the Darkness value is changed, the following ranges determine the Print Darkness and Toner Saver setting values:
Darkness Value Print Darkness Toner Saver Setting Value Setting Value 0.0
Designates the print darkness (model specific).
Legal value: Any non-negative real number from 0.0 to 1.0, inclusive.
For queries, the Print Darkness setting is returned as a real value:
0.1 Lightest 0.3 Lighter 0.5 Normal 0.7 Darker 0.9 Darkest
When the Darkness value is modified, the following ranges are used to determine the Print Darkness setting:
0.0 - 0.2 Lightest >0.2 - 0.4 Lighter >0.4 - 0.6 Normal >0.6 - 0.8 Darker >0.8 - 1.0 Darkest
Key Type Definition · Print Darkness Setting

PageCount integer (Read-only) Page Count
TimeToStandby integer Power Saver. Supported values are:
0 to 120, in minutes
Type name (Read-only) Always returns the value of /Parameters.
Device Parameters for the Parameters Device %Console%
Language name Display Language
Type name (Read-only) Always returns the value of /Parameters.
Device Parameters for the Parameters Device %Calendar%, %CalendarA%, %CalendarB%, %CalendarC%, %CalendarD%
Running boolean Signifies whether time is available for this device.
Type name (Read-only) Value of /Parameters
DateTime string Date and Time in the format: YYYY-MM-DD HH:MM
DayOfWeekLong string Long day name (for example, "Wednesday")
DayOfWeekNum integer Supported values are: 0–6 (0=Sunday)
DayOfWeekShort string Short day name (for example, "Wed")
Device Parameters for the IODevice Device %disk1%
Free integer (Read-only) Indicates the amount of free space available (in pages) on the disk. Valid only if the disk is mounted (mounted is set to True). A value of 0 (zero) indicates that either the disk is not mounted or is full.
HasNames boolean (Read-only) Indicates if the disk supports named files. Valid only if the disk is mounted (mounted is set to True). If the disk is not mounted, the parameter has a value of False.
Key Type Definition · Year integer · BlockSize integer (Read-only)

InitializeAction integer Specifies an action for initializing the disk. Supported values are:
0 Indicates no action; the value returned when the parameter is read. 1 Indicates that the current file system (if any) should be deleted and a new one of LogicalSize created (the disk is assumed to have been formatted already). The disk must first be mounted; otherwise, an ioerror results. 2 Reformats the entire disk before creating a new file system of size LogicalSize. 3 (or greater) has the same effect as the value 2 and also tests the disk x - 2 times. Note: The current file system refers to /FileSystem. See Type as follows for more information.
LogicalSize integer Specifies the size of the file system to be created and is as an argument by InitializeAction.
Legal value: Any non-negative integer, including 0. The value must be less than or equal to the value of PhysicalSize. If set to a value greater than PhysicalSize, or less than zero, a rangecheck error occurs.
Mounted boolean True System attempts to mount the disk. False System attempts to dismount the disk.
A device must contain a valid file system to mount successfully. When a device is mounted, it is known to the system and is readable. To verify if the device is currently mounted, query this parameter immediately after setting it.
PhysicalSize integer (Read-only) Indicates the size of the disk (in pages). Valid only when the disk is mounted. A value of 0 (zero) indicates that the device is not mounted.
Removable boolean (Read-only) Indicates if the drive supports removable disks. Always returns False.
Searchable boolean (Read-only) Indicates if the disk participates in searches in the file system operations that specify a filename without specifying a device.
SearchOrder integer (Read-only) If the Searchable parameter is True, indicates the priority assigned to the disk when searching for a file and no device has been specified. A lower integer indicates a higher priority. If the Searchable parameter is False, this value is ignored.
Type name (Read-only) Always returns the value of /FileSystem.
Writeable boolean (Read-only) Indicates if the files on the disk can be opened for write access. If the disk is write protected, this parameter is a constant equal to False. When the disk is not mounted, this parameter indicates if the drive supports writeable media.
Device Parameters for the IODevice %flash1%
Free integer (Read-only) Indicates the amount of free space available (in pages) on the flash. Valid if the flash is mounted (mounted is set to True). A value of 0 (zero) indicates that either the flash is not mounted or is full.
Key Type Definition · BlockSize integer (Read-only)

HasNames boolean (Read-only) Indicates if the flash parameter is only valid when flash is mounted (mounted is set to True). If flash is not mounted, the parameter has a value of False.
InitializeAction integer Specifies an action for initializing flash:
0 Indicates no action; the value returned when the parameter is read. 1 Indicates that the current file system should be deleted and a new one of PhysicalSize created (the flash must be formatted already). The flash must first be mounted; otherwise, an ioerror results. 2 Reformats the entire flash before creating a new file system of PhysicalSize 3 (or greater) has the same effect as the value 2 and also tests the flash x – 2 times
Legal value: Any non-negative integer.
LogicalSize integer This parameter is not used for InitializeAction.
InitializeAction always formats to PhysicalSize, regardless of what is specified in LogicalSize. A query returns the current size (in pages) of the file system on the device.
A value of 0 (zero) indicates that the device is not mounted.
Legal value: Any non-negative integer, including 0 (zero).
The value of LogicalSize must be less than or equal to the value of PhysicalSize. A rangecheck error occurs if you try to set a larger value or set the value to 0 (zero).
Mounted boolean True System attempts to mount the flash. False System attempts to dismount the flash.
When a device is mounted, it becomes known to the system and is readable, depending on the nature of the device.
A device must contain a valid file system or it will not mount successfully. To verify if the device is currently mounted, query this parameter immediately after setting it.
PhysicalSize integer (Read-only) Indicates the size of the flash (in pages) for a flash that is mounted. A value of 0 indicates that the device is not mounted.
Removable boolean (Read-only) Indicates if the drive supports removable flash.
Searchable boolean (Read-only) Indicates if the flash participates in searches in file system operations that specify a filename without specifying a device.
SearchOrder integer (Read-only) If the Searchable parameter is True, indicates the priority at which the flash is searched for a file in operations where no device has been specified. A lower integer indicates a high priority. If the Searchable parameter is False, the value of this integer has no meaning.
Type name (Read-only) This constant always returns the value of /FileSystem.
Writeable boolean (Read-only) Indicates if the files on the flash can be opened for write access. A write- protected flash returns False. When the flash is not mounted, this parameter indicates if the device supports writeable media.
Key Type Definition

Device Parameters for the IODevice %rom%
Free integer (Read-only) Indicates the amount (in pages) of free space available in ROM. Valid only if the ROM is mounted (mounted is set to True). A value of 0 (zero) indicates that either the ROM is not mounted or it is full.
HasNames boolean (Read-only) Indicates if ROM supports named files. Valid only if ROM is mounted (mounted is set to True). If ROM is not mounted, this parameter has a value of False.
InitializeAction integer (Read-only) Always returns a value of 0 (zero), which indicates no action.
Mounted boolean True System attempts to mount the ROM. False System attempts to dismount the ROM.
When a device is mounted, it becomes known to the system and is readable, depending on the nature of the device.
A device must contain a valid file system or it will not mount successfully. To verify if the device is currently mounted, query this parameter immediately after setting it.
If the ROM device is dismounted, unpredictable results occur.
PhysicalSize integer (Read-only) Indicates the size of the ROM (in pages) that is mounted. A value of 0 (zero) indicates that the device is not mounted. This parameter is only valid when ROM is mounted.
Removable boolean (Read-only) Always False.
Searchable boolean (Read-only) Indicates if ROM participates in searches in file system operations that specify a filename without specifying a device.
SearchOrder integer (Read-only) If the Searchable parameter is True, indicates the priority assigned to the ROM when searching for a file and no device has been specified. A lower integer indicates a higher priority. If the Searchable parameter is False, the value of this integer has no meaning.
Type name (Read-only) Always returns the value of /FileSystem.
Writeable boolean (Read-only) Indicates if the files on the ROM can be opened for write access. Always False.
Key Type Definition · BlockSize integer (Read-only) · LogicalSize integer (Read-only)

Status and Error Messages
Printers return PostScript emulation error messages and status information to the computer through any active interface. To send information to the computer through the parallel interface, configure the interface as bidirectional.
Your printer responds and processes a Ctrl-T (x'14') command as a status query when:
Your printer responds and processes a Ctrl-T (x'14') command as normal data and not a status query when:
When Tagged Binary is active, your printer always responds to a Ctrl-T (x'14') command as a status query and selects the PostScript emulation interpreter to process the current print job. Tagged Binary mode is immediately exited at the end of the print job.

Status Messages
Your printer responds to a Ctrl-T (x'14') status query on an interface by sending a one-line status message back to the host computer over the same interface. If the status query is received between print jobs and the printer is idle with no error conditions, an idle response is returned to the host computer.
Status messages are bracketed by the characters %%[ and ]%%, so the computer software can extract them from other data generated by the current print job. They follow a standard syntax, consisting of one or more key-value pairs, separated by semicolons. For example:
The following table lists the possible keys and value descriptions.
To determine which status message keys your printer supports, see Table C-7 on page C-21.
job The name of the print job, as stored in the JobName entry in statusdict. This field is omitted if the current print job has no defined JobName.
status Printer activity at the time the message is sent:
Idle No job in progress Busy Executing a PostScript emulation program and/or printing pages Waiting I/O wait in mid-job Initializing During startup Not ready Printer menus display or Not Ready displays.
source Source of the job the server is executing:
Serial Parallel Network USB LocalTalk Infrared Internal
This field is omitted if the server is idle.
Key Value Description

Unsolicited Messages
You may receive unsolicited messages from your printer. Unsolicited messages use the same syntax as status messages. These messages are transmitted sequentially as ordinary data through the communication channel, with other characters written to a standard output file. These messages are bracketed with %%[ and ]%%.
The interpreter has detected an error while executing operator and invoked handleerror.
The rest of the current print job is discarded because of a previous error or other ending, such as a stop or Ctrl-C. The printer ignores further input until it determines the end of the print job.
The PostScript emulation program has exited successfully from the server normal save or restore context; therefore, it can make permanent changes to system parameters or virtual memory.

CHAPTER 5: Switching Languages
Your printer may support both PCL emulation and PostScript emulation. Refer to your printer documentation for more information. This chapter describes ways to switch printer languages and explains when you may want to choose one method over another. SmartSwitch is provided with the printer to switch languages. Other methods of switching languages are:
The SmartSwitch feature lets the printer switch to either PCL emulation or PostScript emulation for each interface (parallel, serial, USB, or network). Your printer is shipped from the factory with SmartSwitch set to On for all languages and all interfaces. Consequently, the printer examines all print jobs coming into all its interfaces and switches between PostScript emulation and PCL emulation dynamically.
If a software program explicitly tells the printer which language to use by a PJL command, the printer always accepts and uses that explicit command, regardless of how SmartSwitch has been set from the printer operator panel.
If a software program does not explicitly tell the printer which language to use, the printer examines the incoming data stream and selects the language.

Setting SmartSwitch for Different Interfaces
You can customize your printer so that particular print jobs are sent to particular interfaces. For example, you may want to send all PostScript emulation jobs to the network interface and all PCL emulation jobs to the parallel interface. You can do so by choosing different languages for each interface from the printer operator panel or through MarkVision Professional and setting the selected language to On for the interface you want. Refer to your printer user documentation for more information.
If you have turned off a particular language for an interface, but then decide to send a job to that interface using that language, you must begin the job with a PJL command to override the settings you made from the printer operator panel or through MarkVision Professional. For example, if you set PCL emulation to Off for the serial interface and later decide to send a job in that language through that interface, you must preface the job with a PJL command to override the Off setting. Be sure to end the job with a Universal Exit Language (UEL) command, which is described on page 3-2.
For details on Printer Job Language (PJL) and the PJL ENTER LANGUAGE command, see “ENTER LANGUAGE Command” on page 3-3.

Sniffing
Sniffing is:
The printer examines the received data stream, attempts to determine the type of data stream, and automatically switches to the proper language.
The printer examines the active printer language and decides when an End-of-Job point occurs. End-of-Job points are:

CHAPTER 6: Flash Memory and Disk
Flash memory and disk devices are used to store permanent fonts, macros, and symbol sets. The disk device is also used to buffer print jobs, collate large jobs, and store job statistics. Unlike RAM memory, these devices retain the following information when the printer is powered off, or when the printer switches languages:
Some printers have connectors that let you install optional flash memory or a disk device; other printers may offer one or the other of these devices as a standard feature. Refer to your printer documentation for more information.
When first installed in the printer, the flash memory or disk may be unformatted. You must format the device before you download resources. A message displays on the printer operator panel or through MarkVision Professional if the device is unformatted.
on the device is lost.
If flash memory or a disk becomes full while downloading resources, a message displays on the printer operator panel or through MarkVision Professional. The file being downloaded is not saved unless room is available to store the entire file.

Resource Data Collection (Download Target)
Use the Resource Data Collection (Download Target) mode to save the following information to flash memory or disk:
Resource Data Collection can be turned On and Off by using:
The download target (the destination for the resource data collection) may be RAM (the default), flash memory, or disk.
If you store resources (fonts, macros, or symbol sets) in RAM, the resources can be lost if the printer is reset or if the printer language changes while Resource Save is set to Off. In each case, the resources must be downloaded again. By storing resources on flash memory or disk, the resources become permanent in the printer.

Storing Resources on Flash Memory or Disk
Complete the following steps to download resources to flash memory or disk using the printer operator panel, MarkVision Professional, or a PJL command.
1 Set the download target to flash memory or disk.
Resource Data Collection mode is enabled to the device selected.
2 Download the resources to flash memory or disk using PCL emulation or PostScript emulation.
3 Set Download Target to RAM.
Resource Data Collection mode is disabled.
There are three ways to view the contents of flash memory and disk:
The directory lists the storage device (flash or disk), the names of the files, and the file size. See page 6-4 for a sample directory.

The Directory that prints appears similar to the one below. An explanation of the parts of the Directory follows the example.
Optional Font Memory Size 1048576 bytes Part Name: FLASH Part Number: (none) Write password protected
ID Type Size Prot. Description
=========== ===================================
1000 PCL bitmap font 32140 W ITClublnGrphBkOb
1002 PCL bitmap font 52550 Courier
1003 PCL scalable font 254491 CG Times
PostScript font 134572 Courier
User data 1000 My Program
Demo 1000 My Demo
Unknown file type 1000 My Unknown
248 PCL macro 10 R/W
249 PCL macro 10 mydescription
9 files 476773 bytes used 0 bytes unavailable 571803 bytes free
Expression used to indicate flash memory or disk is installed.
Part Name as it is stored in the flash memory card header. If flash memory is formatted by the printer, the part name field is shown as FLASH. The part name field for the disk is not printed.

Part Number as it is stored in the flash memory card header. If the flash memory is formatted by the printer, the part number field is shown as (none). The part number field for the disk is not printed.
Indicates the entire flash memory or disk is write-protected.
If the device is read/write protected, "Read/Write password protected" is printed. If the device is write-protected, "Write protected" is printed. If the device is not protected, this line is blank.
For more information, see “File and Device Protection Commands” on page 3-93 and “Password Protection” on page 6-7.
Valid for PCL emulation macros, fonts, and symbol sets only. The ID must be used when adding a description to a macro or a symbol set. If two files with the same file type have duplicate IDs, the following occurs:

File types that can be stored on flash memory or disk have unique extensions. The following file types are recognized by the flash format used on earlier printer models; the name of the file type printed in the directory appears in parenthesis.
.t1 (PostScript font) .sFnt5 (PCL scalable font) .bFnt5 (PCL bitmap font) .Mac5 (PCL macro)
Except as noted below, file types listed above are recognized by the flash format used in your printer. In addition, the flash format in your printer also recognizes the following formats:
.data (user data) - any file written with PostScript operators .type1 (PostScript font) - replaces the earlier .t1 extension .demo (demo) - used for demonstration printouts or forms .p5scalable (PCL scalable font) .p5bitmap (PCL bitmapped font) .p5macro (PCL macro) - replaces the earlier .Mac5 extension .p5symset (PCL symbol set)
Usually the PostScript file operators can only read/write files with the extension .data. Use the setfilenameextend operator to read/write other file types, including .demo. Any other file type appears in the list as Unknown File Type. The description column then contains the full filename with the file type (extension).
The size listed for each resource includes the size of the file header.
Prot.
Indicates if the file is password protected.
R/W - read/write protection W - write protection
If this field is blank, then this resource in flash memory or disk is not password protected.
For more information on file protection, see “File and Device Protection Commands” on page 3-93 and “Password Protection” on page 6-7.

The description field for fonts comes from the font header. The description field for macros or symbol sets is blank unless the description field in the file header is set by the PJL LRESOURCE command. See “Printer Unique LRESOURCE Variables” on page 3-52.
The description for macros or symbol sets can be set only once for files stored in flash memory. The description can be set any number of times for macros or symbol sets stored on a disk. The limitation for flash files is due to flash technology. See the “LDESCRIPTION” variable in “Table 3-9: Printer Unique LRESOURCE Variables” on page 3-53 for more information.
You can password protect either the entire flash memory or disk, or files stored on the flash memory or disk.
There are two levels of password protection:
Ensures that the file or device is protected against reading and writing unless the password has been appropriately specified (applies only to actual file data).
Ensures that data cannot be changed on a file or device unless the password has been appropriately specified. A Read/Write password takes precedence over a Write password.
Each file or device can have a separate password. Write passwords ensure that files cannot be deleted, renamed, or updated and a device cannot be formatted or specified as a download target. Read/Write password protection provides the same protection as Write, but additionally ensures that data cannot be read from the file or device.
Read/Write · Write

By using passwords, administrators can ensure data integrity and proper authorization. If flash memory is write password protected, for example, users cannot delete existing files, format the device, or download new files to the device (without first specifying the password). A specific example might be a macro file of an authorizing signature that is stored on flash memory with a Read/Write password. This password ensures that only those authorized can use the signature. All other files (fonts, letterhead, macros) can be unprotected for general use.
Passwords are set, declared, retracted, and deleted using the PJL commands or the MarkVision Professional utility. See “Protecting a File or Device” on page 3-93.
Be aware that once a bit on the flash memory is turned from 1 (binary 1) to 0 (binary 0), it cannot be changed back to binary 1 without a complete flash memory format. As PostScript emulation file operators write data to flash memory, the printer microcode software verifies that none of the bits being set to binary 1 is binary 0. If any attempt is made to change a 0 bit back to 1, a PostScript emulation ioerror occurs.
When a device is formatted, all locations are set to binary 1. This is also the reason descriptions and passwords can be set only once for files on flash memory.

Accessing Files with PostScript Emulation
File Naming Conventions
For any PostScript emulation operator that requires a filename parameter, the filename can be one of the following:
Specifically references a file on a particular device. If the filename does not exist on %device%, no other %device% is accessed for a duplicate filename.
Does not specifically reference a device. The following action occurs:
The term device refers to flash memory, disk, or ROM. For PostScript emulation, some of the operators require or return device names. These operators are: deletefile, filenameforall, devforall, devdismount, devmount, devformat, devstatus. The device always begins and optionally ends with a % character. The following are the valid device names:
The same filename can exist on more than one device. The device prefix determines the actual file to use. For example, %rom%myfile and %flash%myfile designate, respectively, a file called myfile both on the ROM and on flash memory. The device name distinguishes which file to use.

Device names are case sensitive. They must appear exactly as shown.
Each device (except the disk) has one synonym. For example, the flash memory can be referred to as %flash% or %flash1%. The name with the 1 is a unique identifier. This system allows for future expansion of multiple flash memory or disk devices. The disk device name provides for multiple physical units and multiple logical units. Thus,
%disk1_0% indicates the first physical unit and the first (0) logical partition on the device. Currently, one physical device (for ROM, flash memory, and disk) is supported. The disk supports only the first (0) logical partition.
Each file on a device has a unique name to identify the information contained within the file. The name may be up to 127 characters in length. All character codes from X'01' to X'FF' are valid (X'00' is not valid). Filenames are case sensitive: for example,
%flash%myfile and %flash%MYFILE indicate different files on the flash memory.
By default, all files referenced when using the PostScript emulation file operators are given a .data extension. For example, if the following PostScript emulation command occurs,
the file myfile.data is opened on flash memory. The .data extension is added to:
However, it is sometimes necessary to access files by their real name through PostScript emulation. For example, you may want to remove old versions of PCL language resource collection fonts (without formatting the entire device).
To do this, use the PostScript emulation setfilenameextend operator. This operator is in the statusdict dictionary.
(%flash%myfile) (w) file

The value of this operator adds the extension .data to all filenames referenced when using PostScript emulation file operators. To prevent the .data extension from being added, issue the following PostScript emulation command:
To add the .data extension automatically again, issue:
The following example shows how to remove a file for the font myfont from the disk. The PostScript emulation resource collection filename is myfont.type1. The PostScript emulation command to remove the file is:
false setfilenameextend (%disk%myfont.type1) deletefile true setfilenameextend end
For other file types, see page 6-6.
after you disable it. For example, the following PostScript emulation commands generate an undefinedfilename error:
(%disk%iconimage) (w) file dup (0f0606060686c6ff) writestring closefile statusdict begin false setfilenameextend end (%disk%iconimage) (r) file %%[ Error: undefinedfilename; OffendingCommand: file ]%%
This occurs because the filename actually written to disk is iconimage.data. When setfilenameextend is enabled (the default), all PostScript emulation file operators treat filename operands as filename.data; when disabled, they treat filename operands literally.
If you receive unexpected undefinedfilename or similar errors, try toggling setfilenameextend and sending your print job again.

Device Search Order
If you are using the PostScript emulation operators run, file, renamefile, status or eexec, you do not need to specify the device. If you omit the device name, devices are searched in the default order: disk and then flash memory. If the following PostScript emulation code is encountered,
the file on disk is used (since disk occurs before flash memory in the default search order), and files cannot be created in ROM.
The operator deletefile searches only the first device in the default search order if a device is not specified.
Use the PostScript emulation operators devmount, devdismount to change the order. The default search order is determined by the order the devices are mounted. For example, if you want to place the disk device after the flash memory in the default search order, use the following command sequence:
To change the order so the devices are searched as disk, flash memory, and then ROM, use the following PostScript emulation command sequence:
(%flash%) devdismount (%disk%) devdismount (%disk%) devmount (%flash%) devmount (%rom%) devmount
If the device is already mounted, the following operators may change the search order:
Sending these operators has the following effect on the devices in the search order:
2 Formats the device
3 If dismounted in step 1, ( %device% ) devmount
If you do not want a device searched, dismount it and leave it dismounted.

the ROM device.
In the previous examples, the devmount, devdismount operators must be used outside the server loop. We recommend that you place the requests in a stop context so that if the devices do not exist, error recovery can take place.
Previous search orders are not retained. Once a change is made, it remains in effect.
Some performance degradation may occur during initial access to a resource on a disk (as opposed to flash memory or RAM). However, the information is put in cache, and further references to that resource occur at RAM speed.
Device Retrieval Speed Write
Flash Memory 1MB/second 200KB/second
Job buffering to the disk lets you store incoming print jobs on a disk installed on your printer. Although job buffering is designed for individual workstations and networks using MarkVision Professional as the primary tool to control printer operations, you can handle some job buffering functions from the printer operator panel. Refer to your printer user documentation for more details.
Job buffering requires a minimum of 10 percent of disk storage space. For example, if you have an 840MB hard disk installed, you must partition a minimum of 84MB of the disk for job buffering. You must define the size of the job buffer area before you enable buffering for any link ports.
Disk 70KB/second 70KB/second

For minimum acceptable job buffering performance, the hard disk should be able to read and write files at a sustained rate of 600Kb/sec. The Lexmark hard disk option supports this requirement.
Some advantages of job buffering include:
Keep in mind that job buffering may also:
Before job buffering is enabled for a port, you must allocate a portion of the disk for job buffering functions. The minimum size for a job buffering partition is 10 percent of the disk storage space. When a new partition is created, the entire disk is formatted and all resources previously downloaded to the disk are lost.
Once a partition is defined, this disk space is reserved for job buffering.
Once a partition is allocated, job buffering to a disk may be enabled for each active link port. You can enable job buffering from the operator panel menus, if available, or through MarkVision Professional. You cannot enable a port before the partition is allocated. When buffering is enabled from the printer operator panel, a power-on reset (POR) automatically occurs. If buffering is enabled through MarkVision Professional, you must perform a full power-on reset before job buffering can occur.

Disabling Job Buffering
When you disable job buffering, it takes effect immediately on the port you disabled. A POR is automatically performed when job buffering is disabled for any port from the printer operator panel or through MarkVision Professional, so the unused memory resources can be reallocated. When buffering is disabled on a port, any jobs on the disk are printed before normal processing of incoming jobs continues.
To delete or resize a job buffer partition, first delete or print all jobs. Then, disable job buffering on all ports. Finally, delete or resize the job buffer partition.
If the printer loses power, the job being spooled to the disk may be lost. Jobs already stored on the disk remain intact. When power is restored, you are asked if you want to print the jobs held in the buffer. Refer to your printer user documentation for information on how to cancel the jobs or print the jobs held in the buffer.
Jobs that were partially printed during the loss of power are printed again in their entirety when power is restored.

CHAPTER 7: Printer Specifications
This chapter lists printer specifications and information about hardware, environmental conditions, and power requirements.
Room should meet ASHRAE 62–1989 standards.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-Meter Average Sound Pressure, dBA
C510(n) X422 E23x, E33x
Printing 53 51 print; 52 copy; 47 scan/send fax
Duplex printing 55 51 print; 52 copy; 47 scan/send fax
Standby (Idle without Power Saver) 41 30 30
Declared Sound Power Level, Bels
C510(n) X422 E23x, E33x
Printing 6.8 6.4 print; 6.5 copy; 5.9 scan
Duplex printing 7.0 6.4 print; 6.5 copy; 5.9 scan
Standby (Idle without Power Saver) 5.5 4.3 4.1
Status · 51,52 · Status

Electrical Specifications
Printer Model Electrical Specification
C510(n) (100 volt model) 100 V at 50/60 Hz
C510(n) (low voltage model) 110–127 V at 50/60 Hz
C510(n) (high voltage model) 220–240 V at 50/60 Hz
X422 (low voltage model) 100–127 V at 50/60 Hz
X422 (high voltage model) 220–240 V at 50/60 Hz
E23x, E33x (low voltage model) 110–127 V at 50/60 Hz
E23x, E33x (high voltage model) 220–240 V at 50/60 Hz
The following tables list the nominal average power requirements (including fuser power).
Printer Model C5101 X422 E230
State 100 V 120 V 230 V 120 V 230 V 100 V 120 V 230V
430 W 430 W 340 W 340 W 340 W
— — — 475 W 475 W — — —
— — — 125 W 125 W — — —
Idle without Power Saver (Standby)
150 W 150 W 150 W 75 W 75 W 65 W 65 W 65 W
1 Power requirements for network models may differ. 2 This value is

Printer Model C5101 X422 E230
State 100 V 120 V 230 V 120 V 230 V 100 V 120 V 230V
Idle with Power Saver
12 W 12 W 12 W 22 W2 22 W2 6 W 6 W 6 W
Rated short term current
8.1 A 7.2 A 2.83 A 8.8 A 4.1 A 8.6 A 7.7 A 3.4 A
1 Power requirements for network models may differ. 2 This value is
Printer Model E33x E232
State 100 V 120 V 230 V 100 V 120 V 230 V
420 W 420 W 420 W 370 W 370 W 370 W
—
—
Idle without Power Saver (Standby)
80 W 80 W 80 W 65 W 65 W 65W
Idle with Power Saver
7 W 7 W 7 W 6 W 6 W 6 W
Rated short term current
8.6 A 7.7 A 3.4 A 8.6 A 7.7 A 3.4 A
Average continuous printing · Average continuous copying · Average continuous scanning

Physical Specifications
C510, C510n C510dtn X422
Height 385 mm (15.2 in.) 590 mm (23.2 in.) 539.75 mm (21.25 in.)
Width 495 mm (19.5 in.) 495 mm (19.5 in.) 495.3 mm (19.5 in.)
Depth 420 mm (16.5 in.) 525 mm (20.7 in.) 412.75 mm (16.25 in.)
Weight 31.5 kg (69 lb) 42.4 kg (93 lb) 20.41 kg (45 lb)
Height 249 mm (9.8 in.)
Width 396 mm (15.6 in.)
Depth 353 mm (13.9 in.)
Weight 9.98 kg (22 lb)
E230, E232, 234(n), E330, E332n
Left side 203 mm (8 in.) 1 300mm (12 in.)
Right side 508 mm (20 in.) 76.2 mm (3 in.) 300mm (12 in.)
Front 711 mm (28 in.) 1 200mm (8 in.)
1 50mm (2 in.)
Rear 254 mm (10 in.)
355 mm (14 in.) w duplex
Above 584 mm (23 in.)
254 mm (10 in.) 150mm (6 in.)
635 mm (25 in.) w duplex
736 mm (29 in.) w extra tray, whether duplex attached or not
1 When installing the MFP, leave enough room to access the paper tray(s), the multipurpose feeder, the left side door, and the rear exit door.

Environmental Conditions
(cartridges and photoconductors, for example) separately.
Printer Model Operating Value Shipping/Storage Value
C510(n) 10–32.5°C (50–90.5°F) 0–35°C (32–95°F)
X422 15.6–32.2°C (60–90°F) -20–43°C (-4 to 110°F)
E230, E232, E234(n), E330, E332n 15.6–32.2°C (60–90°F) -20–40°C (-4 to 104°F)
Printer Model Operating Value Shipping/Storage Value
C510(n) 15–80% 10–90%
X422 8–80% 8–95% packed;
E230, E232, E234(n), E330, E332n 8–80% 8–95% packed;
Printer Model Altitude (Above Sea Level)
C510(n) 0–2,500 m (8,200 feet)
X422 0–2,500 m (8,200 feet)
E230, E232, E234(n), E330, E332n 0–2,500 m (8,200 feet)
74.6–101.3 kPa (560–760 mmHg)
8–80% unpacked · 8–80% unpacked

Power On to Ready State Time Period
After you turn the printer on, it performs certain internal diagnostics and prepares for printing. The following table lists the approximate time it takes for your printer to perform the internal diagnostics and enter the Ready state. Once the printer enters the
Ready state, it is prepared to print.
network, before it is actually ready to print.
Printer Model Time to Ready (Time in Seconds)1
E230, E232, E234(n), E330, E332n
1Times may be longer with more options attached.
The print wait time may vary as a result of page complexity, page size, paper weight, paper texture, or temperature. Average times are as follows:
Printer Model Time to Print First Page (Time in Seconds)
C510(n) simplex mono 13; simplex color 19; duplex mono 19; duplex color 27
E230 <=10
E232n
C510(n)

CHAPTER 8: Printer Interfaces
Interfaces connect your printer to other devices, such as a computer. The Lexmark C510 has a standard parallel connector (also referred to as a Centronics-type interface) and/or a USB connector. The Lexmark X422 has an internal print server and a USB connector. Some printers also offer a parallel interface option. Refer to your printer user documentation for more information. See page 8-7 for more information about parallel interface.
If a serial connector is required, you may be able to install one of the following:
See page 8-25 for more information about serial interface.
Some printers have standard print servers, but you can also buy optional print servers that connect the printer to Token-Ring or Ethernet networks. For detailed installation or setup instructions, refer to your printer user documentation or the Drivers, MarkVision and Utilities CD. See “Network Support” on page 8-42 for more information about print servers.
Refer to your printer user documentation for information on which printer interface options your printer supports and for detailed installation instructions.

Setting Up the Communications Port
You must establish communication between your printer and computer. To do this, you define your communications port in the application you are using. Instructions for several applications or operating systems are as follows.
In your Windows 95/98/Me application:
1 On the Menu bar, click Start.
2 Click Settings.
3 Click Control Panel. The Control Panel screen displays.
4 Double-click the System icon. The System Properties screen displays.
5 Select the Device Manager tab.
6 Scroll down to Ports and click the + once to expand the list of available Ports.
7 Select the communications port you want to configure.
8 Click the Properties button at the bottom of the screen.
The Communications Port Properties screen for this specific port displays. For example, if you select the COM1 port, then the Communications Port [COM1] Properties screen displays.
9 Select the Port Settings tab.
10 Fill out the fields for the following printer settings to make them match your printer settings:

11 Click OK.
12 Close all windows now that the port is set up.
In your Windows NT 4.0 application:
1 On the Menu bar, click Start.
2 Click Settings.
3 Click Control Panel. The Control Panel screen displays.
4 Double-click the Ports icon. The Ports screen displays.
5 Select the communications port you want to configure.
6 Click the Settings button.
The Settings screen for this specific port displays. For example, if you select the COM1 port, then the Settings for COM1 screen displays.
7 Fill out the fields for the following printer settings to make them match your printer settings:
8 Click OK.
9 Close all screens now that the port is set up.

Setting Up the Communications Port Using Windows 2000
In your Windows 2000 application:
1 On the Menu bar, click Start.
2 Click Settings.
3 Click Control Panel. The Control Panel screen displays.
4 Double-click the System icon. The System Properties screen displays.
5 Select the Hardware tab.
6 In the Device Manager area of the Hardware tab screen, click the Device Manager button. The Device Manager screen displays.
7 Scroll down to Ports and click the + once to expand the list of available Ports.
8 Select the communications port you want to configure and double-click.
The Communications Port Properties screen for this specific port displays. For example, if you select the COM1 port, then the Communications Port [COM1] Properties screen displays.
9 Select the Port Settings tab.
10 Fill out the fields for the following printer settings to make them match your printer settings:
11 Click OK.
12 Close all windows now that the port is set up.

Setting Up the Communications Port Using Windows XP
In your Windows XP application:
1 On the Menu bar, click Start.
2 Click Control Panel. The Control Panel screen displays.
3 Switch the Control Panel to Classic View.
4 Select the Hardware tab.
5 In the Device Manager area of the Hardware tab screen, click the Device Manager button. The Device Manager screen displays.
6 Scroll down to Ports and click the + once to expand the list of available Ports.
7 Select the communications port you want to configure and double-click.
The Communications Port Properties screen for this specific port displays. For example, if you select the COM1 port, then the Communications Port [COM1] Properties screen displays.
8 Select the Port Settings tab.
9 Fill out the fields for the following printer settings to make them match your printer settings:
10 Click OK.
11 Close all windows now that the port is set up.

Deciding Which Interface to Use
On some printers, you can attach multiple interface cables to the printer at the same time. The printer automatically switches to the interface receiving a job. Then it prints the job and begins searching the interfaces for the next job.
One or more of the following is built into your printer: standard parallel connector, USB connector, or network connector. To use a port, connect a cable from the printer to the computer, then set the appropriate values from the printer operator panel or, for network connected printers only, through MarkVision Professional. Refer to your printer user documentation for more information.
Use a parallel interface when you:
Use a USB interface when you:
Use a serial interface when you:
Attach network cables to the Token-Ring or Ethernet print servers installed in your printer. Refer to the MarkNet™ Quick Start book or your user documentation for additional setup information.

Parallel Interface
Use the Lexmark 3.04 m (10 ft) parallel cable part number 1329605, Lexmark 6.1 m (20 ft) parallel cable part number 1427498, or a cable that is IEEE 1284 compliant, to connect your printer to a personal computer or to a host system with a Centronics- compatible parallel port. Use the Lexmark 1.83 m (6 ft) parallel cable, part number 11K4078, to connect your printer to a personal computer or to a host system with a Centronics-compatible parallel port using an optional parallel connector, which is available by installing an RS-232C Serial/Parallel 1284-C Interface Card. Refer to your printer user documentation for the location of the printer parallel connector.
operator panel or through MarkVision Professional. Refer to your printer user documentation for more information.
Your printer can communicate with a computer across the parallel interface in three ways:
This is typically how a computer and printer communicate. When the printer is receiving data from the computer, it can use either Standard or Fastbytes protocol. The burst transfer rate in Fastbytes is faster than in Standard protocol. For best throughput, use Fastbytes protocol.
Your printer can send data to the computer. This capability lets the printer send status messages to the computer on the parallel interface.
These are printer features that enhance reliability of data transfer from the host computer to the printer. See “Parallel Mode 1” on page 8-18 and “Parallel Mode 2” on page 8-19 for more information.

Standard Parallel Connector
The standard IEEE 1284-B compliant parallel connector on the printer is a 36-pin D-shell female receptacle, as shown.
The optional IEEE 1284-C compliant parallel connector on the RS-232C Serial/Parallel 1284-C Interface Card or Parallel 1284-B Interface Card is a 36-pin D-shell female receptacle, as shown.
“Table 8-1: Parallel Connector Pin Assignments” on page 8-9 lists interface and signal information for connector pin assignments for the standard IEEE 1284-B and optional IEEE 1284-C compliant connectors. In this table, “Direction” refers to the direction of signal flow from the printer’s point of view. “Return” denotes twisted pair return.

1 15 STROBE*
In The computer generates this signal to allow the printer to read in data. The signal level is normally high: data is sampled at the falling edge of this pulse.
2–9 6–13 DATA0 through DATA7
In/Out These signals represent data bits 0 to 7, respectively. Each signal is at a high level when data is logical 1, and low when data is logical 0. Pin 2 is the least significant bit.
Out This negative pulse indicates the printer can again accept data.
11 1 BUSY Out A high signal indicates the printer cannot receive data. The signal is high:
A low signal indicates the printer is not busy and the computer can again send data.
12 5 PE Out Paper Exception signal indicates no paper is loaded, a paper jam exists, or a paper feed error occurred.
13 2 SLCT Out Select signal indicates the printer is selected and is online. This signal is normally active. It becomes inactive when the printer is offline.
In Host Busy when Advanced Status is On.
Inverted logic: signal is active when low.
15-17 N/A LOGIC GROUND Logic Ground
N/A means non-applicable.

18 N/A VCC 300 mA of 5 V +/ - 5%
N/A 18 HOST LOGIC HIGH In Driven by the host.
19–30 19–35 GND Return These pins are grounded signals used as twisted pairs with the data and control signals. GND is often called a logic ground, and a fusible link isolates it from chassis ground to offset any large ground shifts when the printer and computer are on different circuits.
In The rising edge of a negative pulse on this line causes the printer to initialize. The printer synchronizes this function with the received data. On the falling edge of INIT*, the printer drives the BUSY interface signal active. On the rising edge of INIT*, the printer:
signal is active when low
To disable INIT* processing, set Honor Init to Off from the printer operator panel or through MarkVision Professional. Refer to your printer user documentation for more information.
Out This signal indicates a printer error condition. The signal level becomes low when the printer is:
This signal is activated approximately 5 seconds after one of the above conditions sets BUSY.
33–35 N/A LOGIC GROUND Not used.
In Set low by host computer to select printer.
signal is active when low
Out Driven by the printer.
N/A means non-applicable.

Using the INIT* Signal to Initialize
When the printer is using the parallel interface and it receives an INIT* signal, it initializes as follows (unless INIT* is disabled by a variable default setting):
This section describes how the parallel interface receives data from the computer.
The cabling in the following illustration supports Standard and Fastbytes protocols and IEEE 1284 Nibble, Byte, and ECP protocols.
25-Pin D-Shell Connector (Male)
36-Pin D-Shell Connector (Male)
Printer Side · Computer Side

The following illustration shows the pin assignments for connecting the 25-pin connector to the 36-pin connector. The symbol * indicates an active low signal.
are supported up to 20 feet. Cable lengths
greater than 20 feet are not supported. The
cable drawing to the left is a functional
representation of the Lexmark cables; it does
not reflect correct pairing of leads or unused
pairs.
The parallel interface consists of an 8-bit parallel data bus with the following characteristics:
– The host system controls 12 lines, which it uses to send data and com-
mands to the printer. – The printer controls five lines. The printer uses two lines to notify the com-
puter when data is transferred successfully and three lines to report printer status. • Controls synchronization with an externally supplied STROBE* pulse.

The cabling in the following illustration supports Standard and Fastbytes protocols and IEEE 1284 Nibble, Byte, and ECP protocols.
36-Pin D-Shell Connector (Male)
25-Pin D-Shell Connector (Male)
11K4078.
Computer Side · Printer Side

The following illustration shows the pin assignments for connecting the 25-pin connector to the 36-pin connector. The symbol * indicates an active low signal.
are supported up to 20 feet. Cable lengths
greater than 20 feet are not supported. The
cable drawing to the left is a functional
representation of the Lexmark cables; it does
not reflect correct pairing of leads or unused
pairs.
The parallel interface consists of an 8-bit parallel data bus with the following characteristics:
– The host system controls 12 lines, which it uses to send data and com-
mands to the printer. – The printer controls five lines. The printer uses two lines to notify the com-
puter when data is transferred successfully and three lines to report printer status. • Controls synchronization with an externally supplied STROBE* pulse.

The following illustration shows the typical data transfer sequence on the parallel interface. See Table 8-2 for typical parallel interface timings on the parallel interface.
A B C
STROBE*
G
D
F
BUSY
E
ACK*

Table 8-2 shows all protocol timings in nanoseconds.
A Data setup to STROBE* low 500 min.
B STROBE* width 500 min.
C Data hold after STROBE* 500 min.
D STROBE* low to BUSY high 500 max.
E ACKNLG* low until ACKNLG* high 500 min.
F ACKNLG* high to BUSY low1 —
G BUSY low and ACKNLG* high to STROBE* low 500 min.
1 Relationship of ACKNLG* and BUSY is not consistent
Your printer is equipped with Fastbytes protocol, which is an enhanced parallel interface protocol. Fastbytes protocol may give you a faster data transfer time on some personal computers and operating systems. Fastbytes protocol is the printer default.
If you have data transmission problems between your personal computer and the printer, change the parallel protocol to Standard. This causes the printer to operate in IEEE-compliant compatibility mode.
The following illustration shows the typical timing sequence.
STROBE*
ACK*
BUSY
Time Name Minimum/Maximum

Table 8-3 shows all protocol timings in nanoseconds
T1 Data setup to STROBE* low 400 min.
T2 STROBE* low to ACKNLG* low 0
T3 ACKNLG* low to STROBE* high 0
T4 STROBE* high to ACKNLG* high 0
T5 ACKNLG* high and BUSY low to STROBE* low 0
T6 ACKNLG* low to change data 50 min.
500 min.
Max based on Auto Strobe Timer
400 min.
Equal to Data Setup Time
T9 ACKNLG* to BUSY Skew +/ - 20 max.
T10 STROBE* high time
400 min.
Equal to Data Setup Time
The printer has a standard IEEE 1284-B compliant connector and is an IEEE 1284-I compliant device. The optional RS-232C Serial/Parallel 1284-C Interface Card has an IEEE 1284-C compliant connector and is an IEEE 1284-I compliant device.
Your printer could be considered an IEEE 1284-II compliant device if the “C” to “B” style connector converter were used. The printer exceeds the maximum allowable circuit capacitance for Level II interfaces. Compliance with IEEE 1284-II may slow data flow control time slightly; however, all minimum and maximum criteria set forth in IEEE 1284 documentation will be met.
The printer supports:
Time Name Minimum/Maximum · T7 STROBE* Timeout · T8 ACKNLG* width

The printer also supports a Device ID function. When queried for its ID, the printer returns the following information:
The LEXPARAL.EXE file is available from ftp.lexmark.com as /pub/driver/ technical_brief/LEXPARAL.EXE. Use your web browser to access ftp:// ftp.lexmark.com/pub/driver/technical_brief/LEXPARAL.EXE
When the Advanced Status menu item is set to On, the printer supports IEEE 1284 communication. If the attached host computer does not support IEEE 1284 communication, you can turn Advanced Status to Off from the printer operator panel or through MarkVision Professional, and SLCTIN* and AUTO FD XT* will be ignored.
slow printer performance.
You can get IEEE 1284 documentation by calling 1-800-678-IEEE (order number DS02709).
Parallel Mode 1 is a feature available for many Lexmark printers. The factory default setting is On or Off depending on your printer model. Refer to your printer user documentation for the factory default for your printer.
If the host side of the parallel interface is using open collector drivers to transmit data to the printer, Parallel Mode 1 should be set to Off to increase reliability of data transfer. Turning this mode Off equalizes all parallel interface signal impedances. On some printer models, you can set Parallel Mode 1 to Off from the printer operator panel, through MarkVision Professional, or through a PJL command. Refer to your printer user documentation for more information.

Parallel Mode 2
Parallel Mode 2 is a feature available for many Lexmark printers. The factory default setting is On.
The timing required by the printer is clearly indicated in “Standard Protocol Data Transfer Sequence” on page 8-15. This is the classic Centronics interface timing.
By setting Parallel Mode 2 to Off from the printer operator panel, through MarkVision Professional, or through a PJL command, the printer changes when data is valid. Once Parallel Mode 2 is set to Off, the printer takes data from the host computer at the trailing edge of STROBE. This is the last possible host driven transition where data should be valid.
problems.
The following diagram illustrates the STROBE receiver for the Lexmark C510.
2.2K ohm ±10%
GND

The following diagram illustrates the STROBE receiver for the Lexmark E230, E232, E330, E332n, and E234(n).
1.1K ohm ±10%
GND
AUTOFD* Receiver for the Lexmark C510
The following diagram illustrates the AUTOFD* receiver for the Lexmark C510.
2.2K ohm ±10%
FCT 2828
GND

The following diagram illustrates the AUTOFD* receiver for the Lexmark E230, E232, E330, E332n, and E234(n).
1.1K ohm ±10%
FCT 2828
GND
DATA 1-8 Signal Driver/Receivers for the Lexmark C510
The following diagram illustrates each of the DATA 1-8 signal driver/receivers for the Lexmark C510.
2.2K ohm ±10%
GND

DATA 1-8 Signal Driver/Receivers for the Lexmark E230, E232, E330, E332n, and E234(n)
The following diagram illustrates each of the DATA 1-8 signal driver/receivers for the Lexmark E230, E232, E330, E332n, and E234(n).
2.2K ohm ±10%
GND
ACKNLG*, ERROR*, SLCT, PE Drivers for the Lexmark C510
The following diagram illustrates the ACKNLG*, ERROR*, SLCT, PE drivers for the Lexmark C510.
2.2K ohm ±10%
FCT 2827 39 ohm ±5%
GND

ACKNLG*, ERROR*, SLCT, PE Drivers for the Lexmark E230, E232, E330, E332n, and E234(n)
The following diagram illustrates the ACKNLG*, ERROR*, SLCT, PE drivers for the Lexmark E230, E232, E330, E332n, and E234(n).
2.2K ohm ±10%
Connector FCT 2827 56 ohm ±5%
GND
BUSY Driver and INIT* Receiver for the Lexmark C510
The following diagram illustrates the BUSY driver and the INIT* receiver for the Lexmark C510.
2.2K ohm ±10%
39 ohm ±5% FCT 2827
FCT 2828
GND
+5V
2.2K ohm ±10% BUSY
FCT 2828 150 pF ±20%

BUSY Driver and INIT* Receiver for the Lexmark E230, E232, E330, E332n, and E234(n)
The following diagram illustrates the BUSY driver and the INIT* receiver for the Lexmark E230, E232, E330, E332n, and E234(n).
1.1K ohm ±10%
56 ohm ±5% FCT 2827
FCT 2828
GND
+5V
2.2K ohm ±10% BUSY
FCT 2828 220 pF ±20%
SLCTIN* Receiver for the Lexmark C510
The following diagram illustrates the SLCTIN* receiver for the Lexmark C510.
1.5K ohm ±10%
FCT 2827 or FCT 2828
Connector Pin 39 ohm ±10%
GND 1650 pF ±20%

The following diagram illustrates the SLCTIN* receiver for the Lexmark E230, E232, E330, E332n, and E234(n).
1.1K ohm ±10%
FCT 2827 or FCT 2828
GND 1720 pF ±20%
The serial interface allows data to flow back and forth between the computer and the printer. However, the serial interface transfers data at a slower rate than the parallel interface.
If a serial connector is required, you may be able to install an RS-232C Serial Interface Card, an External Serial Adapter, or an RS-232C Serial/Parallel 1284-C Interface Card. Refer to your printer user documentation for more information.
The External Serial Adapter supports two serial interface standards: RS-232C and RS-422. The RS-422 serial interface provides more protection from electrical noise than RS-232.
Use RS-232C serial interface if the printer is more than 3.04 m (10 ft) from the computer but less than 15.24 m (50 ft) away. (You can also use a 6.1 m (20 ft) Lexmark cable to connect a printer and a computer located up to 20 feet apart.)
Use RS-422 if your computer is more than 15.24 m (50 ft) away from the printer. You may need to purchase an RS-422 adapter and software for your computer to run RS-422. Refer to your computer documentation for more information. You also need to purchase a custom cable for the serial interface, because serial RS-422 interface pinouts are usually unique to each computer.
Connector Pin · 56 ohm ±10%

When using the serial interface, your printer has the following differences from the serial interface on some other printers:
This section describes how to use the RS-232C serial interface. If you are using RS-422, see “Using the RS-422 Serial Interface” on page 8-36.
Use Lexmark serial cable P/N 1038693 (15.24 m or 50 ft) to connect the serial interface.
The RS-232C serial cable appears as follows:
Pin Signal Direction Description
1 GND Frame Ground
2 TXD Out Transmit Data. The pin transmits data to your computer or terminal.
3 RXD In Receive Data. The pin receives data from your computer or terminal.

Pin Signal Direction Description
4 RTS Out Request to Send. The printer sets this signal high and the signal remains high while the printer is on.
5 CTS In Clear to Send. This pin is optionally used for serial data flow control protocol when in serial mode.
6 DSR In Data Set Ready. This pin is optionally used for data validation, depending on the Honor DSR setting, or flow control, depending on the Serial Protocol setting.
7 GND Logic Ground
20 DTR Out Data Terminal Ready. This pin is optionally used for serial data flow control protocol when in serial mode.

personal computer using a dual asynchronous adapter or an external print server.
If you are using any of the above products, or if your computer has a 9-pin D shell connector that conforms to the IBM designed 9-pin serial port, use a 9-pin to 25-pin cable, such as IBM Part Number 6450242 (254 mm or 10 in.).
Null modem cables, such as Lexmark part number 1038693 [15.24 m (50 ft)], will connect the converter cable to the printer. The illustration below represents the 25-pin connectors for the RS-232C cable (1038693).
The following illustration shows the pin assignments for the 9-pin to 25-pin IBM EIA RS-232C serial cables.
9 to 25 Pin Cable Adapter, Lexmark 1038693 (50 ft)
such as IBM 6450242 (10 in.)
Shield Shield

The following paragraphs show acceptable values for serial communication parameters.
The maximum voltage level for control lines or data lines is +/- 25 positive V dc and +/- 25 negative V dc. A timing or control line is active if the voltage is more than +3 V, or inactive if the voltage is less than –3 V. The voltage reference point is the signal ground on pin 7.
A data signal greater than +3 V means that the bit is a logical 0. A signal less than –3 V means that the bit is logical 1.
For additional information, refer to Interface between Data Terminal Equipment and Data Communications Equipment Employing Serial Binary Data Interchange, published by the Electronic Industries Association, publications EIA RS-232C and EIA\TIA-232-E.
The computer sends serial data in data frames (also known as packets). You can create 10-bit, 11-bit, and 12-bit data frames and set the serial data transfer parameter so that each data frame contains 7 or 8 data bits. However, your printer is an 8-bit printer; characters, controls, and all points addressable (APA) graphics need 8 bits of data. If you select 7-bit data transfer, some unexpected characters might print.
The list of acceptable data transfer rates (in bits per second) can be accessed from the printer operator panel or through MarkVision Professional. Refer to your printer user documentation for more information.
The printer sends or receives 7 or 8 data bits in each transmission frame, depending on which one is selected.

The printer receives data with 1 start bit and either 1 or 2 stop bits. The printer always sends 1 start and 2 stop bits.
There are four possible parity settings: Odd, Even, None, and Ignore.
Odd The port expects to receive data frames with an odd number of logical 1’s per byte. The printer transmits XOFF and XON with odd parity. If the printer detects a parity error, the port sends X'5F' to the printer instead of the character sent by the host system.
Even The port expects to receive data frames with an even number of logical 1’s per byte. The port transmits XOFF and XON with even parity. If the port detects a parity error, the port sends an inverted question mark to the printer instead of the character sent by the host system.
None The port expects no parity bit when it receives data. The port transmits XON and XOFF without parity bits.
Ignore The port expects a parity bit when the port receives a data frame. The port ignores the parity bit. The port uses even parity when it transmits XON and XOFF.
Some printers post a 54 Standard Serial Error or a 54 Serial Option x Error (x represents the number of the serial port) the first time they detect a transmission error (parity, overrun, or framing). The 54 Standard Serial Error or the 54 Serial Option x Error can be reset from the printer operator panel or through MarkVision Professional. Refer to your printer user documentation for more information.
If repeated serial errors occur, power the printer off and then back on to restore proper serial operation.

Data flow control is accomplished through the following lines:
Five data flow control protocols are available:
Your printer supports two modes in which both hardware and software data flow control protocols are performed. In XON/XOFF/DTR mode, the printer uses both XON/XOFF and DTR pacing. When XON/XOFF/DTR/DSR mode is active, the printer uses both XON/XOFF and DTR/DSR pacing.
Robust XON may be selected when the data flow control protocol for the serial port is set to XON/XOFF, XON/XOFF/DTR, or XON/XOFF/DTR/DSR pacing. The printer sends a continuous stream of XON signals to the host computer to indicate that the serial port is ready to receive additional data. The signals continue as long as one of the following conditions exist:
Refer to your printer user documentation for more information about selecting the protocol from the printer operator panel or through MarkVision Professional.

Table 8-5 shows the state or function of each serial interface signal in the three data flow control protocols when the Honor DSR setting is On.
XON/XOFF Protocol (Honor DSR On)
DTR Protocol (Honor DSR On)
DTR/DSR Protocol (Honor DSR On)
DTR Always active Flow control to computer Flow control to computer
DSR Data validity Data validity Flow control (transmit mode) to computer (receive mode)
CTS Ignored Flow control from computer Ignored
Table 8-6 shows the state of each serial interface signal in the three data flow control protocols when the Honor DSR setting is Off.
XON/XOFF Protocol (Honor DSR Off)
DTR Protocol (Honor DSR Off)
DTR/DSR Protocol (Honor DSR Off)
DTR (Output) Always active Flow control to computer
Flow control to computer
DSR (Input) Ignored Ignored1 Flow control to computer
CTS (Input) Ignored Flow control from computer1
1 These values are compatible with Hewlett-Packard Company’s LaserJet printers.
Printer · Printer Signal · Ignored

Use DTR to pace the data flow from the computer. DTR goes from high to low to indicate to the computer that the printer cannot receive more data when it detects the following BUSY conditions:
The following diagram illustrates DTR Protocol Timing.
1 The RTS signal is driven active as long as power is supplied to the printer.
2 The DTR signal becomes active when initialization is complete, telling the computer that the printer is ready to receive data.
3 When Honor DSR is On, the printer considers data received invalid when DSR is low and discards the data. Only DTR/DSR is used for flow control from the printer to the host computer.
4 DTR drops to tell the computer that the receive buffer is nearly full or that the printer is busy and that data transmission should stop. About 640 free bytes remain in the buffer at this time. If the computer continues to send data after the printer has sent a low DTR signal, data could be lost.
Receive Data Valid

When you select this data flow control protocol, the printer sends an XOFF signal when it detects the following BUSY conditions:
The following diagram illustrates XON/XOFF Protocol Timing.
DTR
DSR
XON XOFF XON
XMT
RXD
Legend:
1 The RTS signal is driven active as long as power is supplied to the printer.
2 The DTR signal becomes active at the completion of initialization.
3 The printer considers data received invalid when DSR is low and discards the data. (This is conditional depending on the setting of Honor DSR.)
4 After you power on the printer and DTR is active, the printer sends an XON signal to the computer (DC1 control or X'11'). However, the computer does not need to detect this initial XON before sending data to the printer, because the printer can be powered on before the computer or terminal.
5 The printer sends an XOFF signal (DC3 control or X'13') to request that data transmission end until the buffer clears. About 640 free bytes remain in the buffer at this time. If the computer continues to send data after the printer sent an XOFF signal, data could be lost.
6 The printer sends an XON signal to the computer when the buffer space is again available. The serial interface is ready to receive more data.
Receive Data Valid

The printer places an underscore character in the link buffer when it detects an error. Some printers also display serial errors on the printer operator panel or through MarkVision Professional as attendance messages, such as a 54 Standard Serial Error or 54 Serial Option x Error (x represents the number of the serial port). Serial errors that do not generate such an error message are:
For correct operation of the serial interface, your printer and your computer operating system must be configured identically. The following is an example of how to configure DOS for the printer using serial DTR protocol:
From the DOS prompt, enter the following commands:
mode comy:9600,n,8,1,p
mode lptx :=comy
where x equals 1, 2, or 3, and y equals 1 or 2
Include these two command statements in the AUTOEXEC.BAT file on the computer so they run each time your system starts operating.
Once this is set, to copy to the communications port again use the copy command:
copy 'filename' lptx

For correct operation of the RS-232C serial interface, while setting up your communications port, make sure you selected Hardware in the Flow Control field. Selecting Hardware sets the communication to DTR protocol. See the following sections for more information:
The RS-232C port (on the RS-232C Serial Interface Card or the RS-232C Serial/Parallel 1284-C Interface Card) is compatible with the Plug and Play External COM Device Draft Specification, Rev. 0.86.
Devices that are compatible with Plug and Play COM can:
This section describes how to use the RS-422 serial interface. If you are using RS-232, see “Using the RS-232C Serial Interface” on page 8-26.
You need to purchase a custom cable for RS-422 support. You may also need to purchase an adapter card and software to run RS-422 on your computer. Contact the place where you bought your printer.

The RS-422 serial cable appears as follows:
Pin assignments for this 25-pin connector are shown in Table 8-7. You can set the polarity of these signals from the printer operator panel or through MarkVision Professional.
Pin Signal Direction Description
1 GND Logic Ground
15 RXD* In Receive Data
17 RXD In Receive Data
19 TXD* Out Send (transmit) Data
25 TXD Out Send (transmit) Data
The following illustration shows how the pins are used:

The following paragraphs show acceptable values for serial communication parameters.
RS-422 serial interface uses a differential pair, 5-volt typical delta, 0.5 volt threshold. Your printer uses a TI75179 transceiver with transorbs. The polarity of the signals is programmable.
The computer sends serial data in data frames (also known as packets). You can create 10-bit, 11-bit, or 12-bit data frames and set the serial data transfer parameter so that each data frame contains 7 or 8 data bits. However, your printer is an 8-bit printer; characters, controls, and APA graphics need 8 bits of data. If you select 7-bit data transfer, some unexpected characters might print.
The list of acceptable data transfer rates (in bits per second) can be accessed from your printer operator panel or through MarkVision Professional. Refer to your printer user documentation for more information.
Your printer sends or receives 7 or 8 data bits in each transmission frame, depending on which one is selected.
Your printer receives data with 1 start bit and either 1 or 2 stop bits. The printer always sends 1 start and 2 stop bits.

There are four possible parity settings: Odd, Even, None, and Ignore.
Odd The port expects to receive data frames with an odd number of logical 1’s per byte. The printer transmits XOFF and XON with odd parity. If the printer detects a parity error, the port sends X'5F' to the printer instead of the character sent by the host system.
Even The port expects to receive data frames with an even number of logical 1’s per byte. The port transmits XOFF and XON with even parity. If the port detects a parity error, the port sends an inverted question mark to the printer instead of the character sent by the host system.
None The port expects no parity bit when it receives data. The port transmits XON and XOFF without parity bits.
Ignore The port expects a parity bit when the port receives a data frame. The port ignores the parity bit. The port uses even parity when it transmits XON and XOFF.
Some printers post a 54 Standard Serial Error or a 54 Serial Option x Error (x represents the number of the serial port) the first time they detect a transmission error (parity, overrun, or framing). The 54 Standard Serial Error or the 54 Serial Option x Error can be reset from your printer operator panel or through MarkVision Professional. Refer to your printer user documentation for more information.
If repeated serial errors occur, power the printer off and back on to restore proper serial operation.
One data flow control protocol is available: XON/XOFF with programmable polarity. Refer to your printer user documentation for more information about selecting the protocol from your printer operator panel or through MarkVision Professional.

When you select this data flow control protocol, your printer sends an XOFF signal when it detects the following BUSY conditions:
XMT
RXD
transmission end until the buffer clears. About 640 free bytes remain in the buffer at this time. If the computer continues to send data after the printer sends an XOFF signal, data could be lost.
Your printer places an underscore character in the link buffer when it detects an error. Some printers post a 54 Standard Serial Error or a 54 Serial Option x Error (x represents the number of the serial port) the first time they detect a transmission error (parity, overrun, or framing). The 54 Standard Serial Error or the 54 Serial Option x Error can be reset from your printer operator panel or through MarkVision Professional. Refer to your printer user documentation for more information.
If repeated serial errors occur, power the printer off and then back on to restore proper serial operation.
The Serial errors that do not generate such an error message are:

For correct operation of the RS-422 serial interface, make sure you have:
The following is an example of how to configure DOS for the printer using serial XON\XOFF protocol:
Run the software you received that supports your RS-422 adapter card or complete the following:
From the DOS prompt, enter the following commands:
mode comy:9600,n,8,1,p
mode lptx :=comy
where x equals 1, 2, or 3, and y equals 1 or 2
Include these two command statements in the AUTOEXEC.BAT file on the computer so they run each time your system starts operating.
Once this is set, to copy to the communications port again use the copy command:
copy 'filename' lptx

For correct operation of the RS-422 serial interface, while setting up your communications port, make sure you have selected Xon/Xoff in the Flow Control field. Selecting Xon/Xoff sets the communication to Xon/Xoff protocol. See the following sections for more information:
Installing an internal print server enables you to connect your printer to a local area network (LAN). The print server supports these network interfaces:
For information on installing a print server in your printer, refer to your printer user documentation.
You may also connect your printer to a LAN by using an external print server. Use one of the following:

printer user documentation for more information.
Your printer has an input (link) buffer for each interface. The maximum size of the input buffer depends upon the amount of RAM memory installed. The input buffers serve the same purpose as a print spooler and can be allocated automatically by the printer. The size of the input buffer may be modified or disabled from the operator panel menus or through MarkVision Professional.
If NPAP is active on a port, two-thirds of the buffer memory is reserved for NPAP and one-third is set aside for the input buffer. If NPAP is not active, all the memory is available for the input buffer.
Table 8-8 shows the sizes automatically selected for the buffers when the buffer size is set to Auto in the menus.
Network Buffer Size LocalTalk USB Fax
Memory Size Parallel Buffer Size
4MB 12K 12K 48K 12K 12K 350K
6MB 24K 12K 48K 24K 12K 350K
8, 10, or 12MB 48K 24K 48K 48K 24K 350K
16, 18, or 20MB 48K (1MB if no optional adapter is installed) 24K 1MB 1MB 24K 1MB
24, 28, 32, or 34MB 192K (1MB if no optional adapter is installed) 150K 1MB 1MB 150K 1MB
36, 38, or 40MB 384K (1MB if no optional adapter is installed) 300K 1MB 1MB 300K 1MB
44MB or larger 2MB 300K 2MB 2MB 300K 1MB
N/A means non-applicable.
stop transmitting bytes when the serial input buffer is within 640 bytes. In addition, when XON/XOFF protocol is used, the printer signals the host computer to stop transmitting when the serial input buffer is 384, 256, and 128 bytes from full.
Serial Buffer Size

APPENDIX A: PCL Support
Table A-1 lists PCL emulation commands and identifies printers that support them.
For detailed information about PCL emulation commands and how to select them, see “PCL Emulation” on page 2-1.
Table A-2 on page A-6 identifies printer support for the GL/2 commands.
Supported ✘ Not Supported
Page numbers reference command descriptions. Printer Model
ESCE Printer Reset 2-62
ESCY Display Functions-On 2-83
ESCZ Display Functions-Off 2-84
ESCz Print Test Page 2-84 ✘ ✘ ✘
ESC&a#C Horizontal Cursor Position (in Columns) 2-68
ESC&a#G Duplex Page Side Selection 2-67
ESC&a#H Horizontal Cursor Position (in Decipoints) 2-68
ESC&a#L Set Left Margin 2-65
ESC&a#M Set Right Margin 2-65
ESC&a#P Print Direction 2-65
ESC&a#R Vertical Cursor Position (in Rows) 2-69
ESC&a#V Vertical Cursor Position (in Decipoints) 2-69
ESC&b#M Monochrome Print Mode 2-80
ESC&c#T Character Text Path Direction 2-65
ESC&d@ Underline-Disable 2-71
ESC&d#A Number of Collated Copies 2-62
ESC&d#D Underline-Enable 2-71

Supported ✘ Not Supported
Page numbers reference command descriptions. Printer Model
ESC&f#F Set Universal Height 2-64
ESC&f#G Set Universal Width 2-64
ESC&f#O Set Universal Feed Direction 2-65
ESC&f#W Set Universal Custom Name 2-65
ESC&f#S Push / Pop Cursor Position 2-69
ESC&f#X Macro Control 2-73
ESC&f#Y Set Macro ID 2-73
ESC&k#G Set Line Termination 2-69
ESC&k#H Set Horizontal Motion Index 2-66
ESC&k#S Select Primary and Secondary Pitch 2-72
ESC&k#W Text Scale Mode 2-67 ✘ ✘ ✘
ESC & l #C Set Vertical Motion Index 2-66
ESC & l #D Set Line Spacing 2-67
ESC & l #E Set Top Margin 2-65
ESC & l #F Set Text Length 2-66
ESC & l #G Set Output Bin 2-66
ESC & l #H Paper Source 2-64
ESC & l #L Skip Perforation 2-66
ESC & l #O Select Orientation 2-65
ESC & l #M(b) Paper Type 2-84 ✘ ✘ ✘
ESC & l #P Set Page Length 2-67
ESC & l #S Simplex/Duplex Print 2-62
ESC & l 1T Job Separation 2-65 ✘ ✘ ✘
ESC & l #U Long-Edge Offset Registration 2-62
ESC & l #X Number of Copies 2-62
ESC & l #Z Short-Edge Offset Registration 2-62
ESC&n#W [operation] [string id]
Alphanumeric ID 2-68

Supported ✘ Not Supported
Page numbers reference command descriptions. Printer Model
ESC&p#C Palette Control 2-80
ESC&p#I Palette Control ID 2-80
ESC&p#S Select Palette 2-80
ESC&p#X[data] Transparent Print Data 2-71
ESC&r#F Flush All Pages 2-82
ESC&s#C End-Of-Line Text Wrap 2-83
ESC&t#P Text Parsing Method 2-72
ESC&u#D Unit of Measure 2-63
ESC(# Primary Font Symbol Set 2-70
ESC(#X Select Primary Download Font (by Font ID) 2-71
ESC(3@ Select Default Primary Font 2-71
ESC(f#W[data] Define Symbol Set 2-72
ESC(s#B Primary Font Stroke Weight 2-71
ESC(s#H Primary Font Pitch 2-70
ESC(s#P Primary Font Spacing 2-70
ESC(s#S Primary Font Style 2-70
ESC(s#T Primary Font Typeface Selection 2-71
ESC(s#V Primary Font Height (Point Size) 2-70
ESC(s#W[data] Load Character 2-73
ESC)# Secondary Font Symbol Set 2-70 ✘ ✘ ✘
ESC)#X Select Secondary Download Font (by Font ID) 2-71 ✘ ✘ ✘
ESC)3@ Select Default Secondary Font 2-71
ESC)s#B Secondary Font Stroke Weight 2-71 ✘ ✘ ✘
ESC)s#H Secondary Font Pitch 2-70 ✘ ✘ ✘
ESC)s#P Secondary Font Spacing 2-70 ✘ ✘ ✘
ESC)s#S Secondary Font Style 2-70 ✘ ✘ ✘
ESC)s#T Secondary Font Typeface Selection 2-71 ✘ ✘ ✘
ESC)s#V Secondary Font Height (Point Size) 2-70 ✘ ✘ ✘
ESC)s#W[data] Load Font Header 2-73

Supported ✘ Not Supported
Page numbers reference command descriptions. Printer Model
ESC*b#M Set Raster Compression Mode 2-78
ESC*b#V[data] Transfer Raster Data (by Plane) 2-77
ESC*b#W[data] Transfer Raster Data (by Row / Block) 2-78
ESC*b#Y Y Offset 2-77
ESC*c#A Horizontal Rectangle Size (in PCL Units) 2-75
ESC*c#B Vertical Rectangle Size (in PCL Units) 2-75
ESC*c#D Set Font ID 2-73
ESC*c#E Set Character Code 2-73
ESC*c#F Font Control 2-73
ESC*c#G Area Fill ID 2-74, 2-76
ESC*c#H Horizontal Rectangle Size (in Decipoints) 2-75
ESC*c#K GL/2 Horizontal Plot Size (in Inches) 2-83
ESC*c#L GL/2 Vertical Plot Size (in Inches) 2-83
ESC*c#P Fill Rectangular Area 2-76
ESC*c#Q Pattern Control 2-75
ESC*c#R Symbol Set ID Code 2-72
ESC*c#S Symbol Set Control 2-72
ESC*c0T Set Picture Frame Anchor Point 2-83
ESC*c#V Vertical Rectangle Size (in Decipoints) 2-75
ESC*c#W[data] User-Defined Pattern 2-75
ESC*c#X Picture Frame Horizontal Size (in Decipoints) 2-83
ESC*c#Y Picture Frame Vertical Size (in Decipoints) 2-83
ESC * l #R Pixel Placement 2-74
ESC * l #W[data] Color Lookup Tables 2-80
ESC*m#W[data] Download Dither Matrix 2-80
ESC*o#M(b) Print Quality 2-84 ✘ ✘ ✘
ESC*o#W[data] Driver Configuration Command 2-80

Supported ✘ Not Supported
Page numbers reference command descriptions. Printer Model
ESC*p#P Push / Pop Palette 2-80
ESC*p#R Set Pattern Reference Point 2-75
ESC*p#X Horizontal Cursor Position (in PCL Units) 2-68
ESC*p#Y Vertical Cursor Position (in PCL Units) 2-69
ESC*r#A Start Raster Graphics 2-77
ESC*r#F Raster Graphics Presentation Mode 2-77
ESC*r#S Raster Width (Source) 2-77
ESC*r#T Raster Height (Source) 2-77
ESC*r#U Simple Color 2-80
ESC*rB End Raster Graphics (Version B) 2-78
ESC*rC End Raster Graphics (Version C) 2-78
ESC*s#I Inquire Status Readback Entity 2-82
ESC*s1M Free Space 2-82
ESC*s#T Set Status Readback Location Type 2-82
ESC*s#U Set Status Readback Location Unit 2-82
ESC*s#X Echo 2-82
ESC*t#H Raster Width Destination 2-78
ESC*t#I Gamma Correction 2-81
ESC*t#J Render Algorithm 2-81
ESC*t#R Raster Resolution 2-77
ESC*t#V Raster Height Destination 2-79
ESC*g#W Set Raster Configuration 2-79 ✘ ✘ ✘
ESC*v#A Color Component One 2-81
ESC*v#B Color Component Two 2-81
ESC*v#C Color Component Three 2-81
ESC*v#I Assign Color Index 2-81
ESC*v#N Source Transparency Mode 2-74
ESC*v#O Pattern Transparency Mode 2-74
ESC*v#S Foreground Color 2-81

Supported ✘ Not Supported
Page numbers reference command descriptions. Printer Model
ESC*v#T Select Current Pattern 2-74
ESC*v#W[data] Configure Image Data 2-81
ESC*i#W[data] Viewing Illuminant 2-81 ✘ ✘ ✘
ESC9 Clear Horizontal Margins 2-65
ESC= Half Line-Feed 2-69
ESC%#A Enter PCL Emulation 2-83
ESC%#B Enter GL/2 Language
2-83
ESC%–12345X Universal Exit Language (UEL) / Start of PJL 2-63
Table A-2 lists GL/2 commands and identifies the printers that support them.
Supported ✘ Not Supported
Page numbers reference command descriptions. Printer Model
AA Arc Absolute 2-85
AC Anchor Corner 2-87
AD Define Alternate Font 2-86
AR Arc Relative 2-85
AT Arc Absolute Three Point 2-85
BR Bezier Relative 2-85
BZ Bezier Absolute 2-85
CF Character Fill 2-86
CI Circle 2-85

Supported ✘ Not Supported
Page numbers reference command descriptions. Printer Model
CO Comment 2-84
CP Character Plot 2-86
CR Color Range 2-87
DF Default 2-84
DI Absolute Direction 2-86
DR Relative Direction 2-86
DT Define Label Terminator 2-86
DV Define Variable Text Path 2-86
EA Edge Rectangle Absolute 2-85
EP Edge Polygon 2-85
ER Edge Rectangle Relative 2-85
ES Extra Space 2-86
EW Edge Wedge 2-85
FI Primary Font 2-86
FN Secondary Font 2-86
FP Fill Polygon, Odd/Even 2-85
FP Fill Polygon, Non-Zero Winding 2-85
FT Fill Type 2-87
FT Fill Type - 22 2-87
FT Fill Type - 9 2-87
IN Initialize 2-84
IP Input P1 and P2 2-84
IR Input Relative P1 and P2 2-85
IW Input Window 2-85
LA Line Attributes 2-87
LB Label, Default Terminator = ‘03’x 2-86
LO Label Origin 2-86
LO Uses PCL Label Origin 2-86
LT Line Type 2-87

Supported ✘ Not Supported
Page numbers reference command descriptions. Printer Model
LM Label Mode 2-86 ✘ ✘ ✘
MC Logical Operation 2-85
NP Number of Pens 2-87
PA Plot Absolute 2-85
PC Pen Color 2-87
PD Pen Down 2-85
PE Polyline Encoded 2-85
PM Polygon Mode 2-85
PP Pixel Placement 2-85
PR Plot Relative 2-85
PU Pen Up 2-85
PW Pen Width 2-87
RA Fill Rectangle Absolute 2-86
RF Define Raster Fill 2-87
RO Rotate Coordinate System 2-85
RR Fill Rectangle Relative 2-86
RT Arc Relative Three Point 2-85
SA Select Alternate Font 2-86
SB Scalable/Bitmapped Fonts 2-86
SC Scale 2-85
SD Define Standard Font 2-86
SI Absolute Character Size 2-86
SL Character Slant 2-86
SM Symbol Mode 2-87
SP Select Pen 2-87
SR Relative Character Size 2-86
SS Select Standard Font 2-86
SV Screened Vectors 2-87
SV Screened Vectors - 9, level 2-87

Supported ✘ Not Supported
Page numbers reference command descriptions. Printer Model
TD Transparent Data 2-86
TM Threshold Matrix 2-87
TR Transparency Mode 2-87
UL User Defined Line 2-87
WG Fill Wedge 2-86
WU Pen Width Units 2-87

APPENDIX B: PJL Support
The following tables list PJL commands and identify printers that support them.
For detailed information about PJL commands, see “Printer Job Language” on page 3-1. All commands may not have a full description.
printer and the Hewlett-Packard Company’s LaserJet printers.
Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only. Default values are listed for exceptions only.
AUTOSELECT ✘ ✘ ✘
BINDING 3-12
BITSPERPIXEL 3-12 ✘ ✘
CLEARABLEWARNINGS 3-12 ✘
CONTEXTSWITCH ✘ ✘ ✘
COPIES 3-12
CPLOCK 3-13
DENSITY 3-13
DISKLOCK ✘ ✘
DUPLEX 3-13
ECONOMODE 3-13 ✘
FORMATTERNUMBER 3-13
FORMLINES 3-13
HOLD 3-13 ✘
HOLDKEY 3-13 ✘

Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only. Default values are listed for exceptions only.
IMAGEADAPT 3-14 ✘ ✘ ✘
INTRAY1 ✘ ✘ ✘
INTRAY2 3-14 ✘
INTRAY3 3-14 ✘ ✘ ✘
INTRAY4 3-14 ✘ ✘ ✘
INTRAY5 3-14 ✘ ✘ ✘
INTRAY1SIZE 3-14
INTRAY2SIZE 3-14
INTRAY3SIZE 3-14 ✘ ✘ ✘
INTRAY4SIZE 3-14 ✘ ✘ ✘
INTRAY5SIZE 3-14 ✘ ✘ ✘
IOBUFFER ✘ ✘ ✘
IOSIZE ✘ ✘ ✘
JOBATTR ✘ ✘ ✘
JOBNAME 3-14 ✘
JOBOFFSET 3-15 ✘ ✘ ✘
LANG 3-15
LOWTONER 3-15 CONTINUE
MANUALFEED 3-15 ✘
MEDIASOURCE ✘ ✘ ✘
MEDIATYPE 3-15
MPTRAY 3-15 ✘ ✘
ORIENTATION 3-15
OUTBIN 3-16
PAGEPROTECT 3-16
PAPER 3-16
PARALLEL 3-17 ✘ ✘
PASSWORD 3-17

Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only. Default values are listed for exceptions only.
POWERSAVE 3-17
POWERSAVETIME 3-18
PRINTQUALITY ✘ ✘ ✘
QTY 3-18 ✘
RENDERMODE ✘ ✘ ✘
REPRINT 3-18
RESOLUTION 3-18
RESOURCESAVE 3-18 AUTO
RESOURCESAVESIZE ✘ ✘ ✘
RET 3-18 ✘ ✘ ✘
TIMEOUT 3-18
USERNAME 3-19 ✘
WIDEA4 3-19 ✘
Table B-2: Printer Unique PJL Variables for Both Printer Languages
Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only. Default values are listed for exceptions only.
LADVANCEDSTATUS 3-19 ✘
LALARMCONTROL 3-19 ✘
LAUTOCRLF 3-19
LAUTOLFCR 3-19

Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only. Default values are listed for exceptions only.
LBONDLENGTH 3-19 ✘ ✘ ✘
LBONDLOADING 3-19 ✘
LBONDOUTBIN 3-20 ✘ ✘ ✘
LBONDTEXTURE 3-20 ✘
LBONDWEIGHT 3-20
LBWLOCK 3-20 ✘ ✘
LCANCEL 3-20
LCARDSTOCKLENGTH 3-20 ✘ ✘ ✘
LCARDSTOCKLOADING 3-20 ✘ ✘
LCARDSTOCKOUTBIN 3-21 ✘ ✘ ✘
LCARDSTOCKTEXTURE 3-21 ✘
LCARDSTOCKWEIGHT 3-21
LCOLLATION 3-21
LCOLORCORRECTION 3-21 AUTO ✘ ✘
LCOLOREDLENGTH 3-21 ✘ ✘ ✘
LCOLOREDLOADING 3-22 ✘
LCOLOREDOUTBIN 3-22 ✘ ✘ ✘
LCOLOREDTEXTURE 3-22 ✘
LCOLOREDWEIGHT 3-22
LCOLORMODEL 3-22 ✘ ✘
LCUSTOMPAPERUNITS 3-22
LCUSTOMPAPERWIDTH 3-22 216 mm (8.5 in.)
LCUSTOMPAPERHEIGHT 3-23 356 mm (14.0 in.)
LCUSTOMTYPE1LENGTH 3-23 ✘ ✘ ✘
LCUSTOMTYPE1LOADING 3-23
LCUSTOMTYPE1MEDIA 3-23
LCUSTOMTYPE1NAME 3-23

Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only. Default values are listed for exceptions only.
LCUSTOMTYPE1TEXTURE 3-24 ✘
LCUSTOMTYPE1WEIGHT 3-24
LCUSTOMTYPE2LENGTH 3-24 ✘ ✘ ✘
LCUSTOMTYPE2LOADING 3-24
LCUSTOMTYPE2MEDIA 3-24
LCUSTOMTYPE2NAME 3-25
LCUSTOMTYPE2OUTBIN 3-25 ✘ ✘ ✘
LCUSTOMTYPE2TEXTURE 3-25 ✘
LCUSTOMTYPE2WEIGHT 3-25
LCUSTOMTYPE3LENGTH 3-25 ✘ ✘ ✘
LCUSTOMTYPE3LOADING 3-25 ✘ ✘
LCUSTOMTYPE3MEDIA 3-26 ✘
LCUSTOMTYPE3NAME 3-26 ✘
LCUSTOMTYPE3OUTBIN 3-26 ✘ ✘ ✘
LCUSTOMTYPE3TEXTURE 3-26 ✘
LCUSTOMTYPE3WEIGHT 3-26 ✘
LCUSTOMTYPE4LENGTH 3-26 ✘ ✘ ✘
LCUSTOMTYPE4LOADING 3-27 ✘ ✘
LCUSTOMTYPE4MEDIA 3-27 ✘
LCUSTOMTYPE4NAME 3-27 ✘
LCUSTOMTYPE4OUTBIN 3-27 ✘ ✘ ✘
LCUSTOMTYPE4TEXTURE 3-27 ✘
LCUSTOMTYPE4WEIGHT 3-27 ✘
LCUSTOMTYPE5LENGTH 3-28 ✘ ✘ ✘
LCUSTOMTYPE5LOADING 3-28 ✘ ✘
LCUSTOMTYPE5MEDIA 3-28 ✘
LCUSTOMTYPE5NAME 3-28 ✘
LCUSTOMTYPE5OUTBIN 3-28 ✘ ✘ ✘

Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only. Default values are listed for exceptions only.
LCUSTOMTYPE5WEIGHT 3-29 ✘
LCUSTOMTYPE6LENGTH 3-29 ✘ ✘ ✘
LCUSTOMTYPE6LOADING 3-29 ✘ ✘
LCUSTOMTYPE6MEDIA 3-29 ✘
LCUSTOMTYPE6NAME 3-29 ✘
LCUSTOMTYPE6OUTBIN 3-29 ✘ ✘ ✘
LCUSTOMTYPE6TEXTURE 3-30 ✘
LCUSTOMTYPE6WEIGHT 3-30 ✘
LDOWNLOADTARGET 3-30
LDRYTIMEDELAY 3-30 ✘ ✘ ✘
LDUPLICATEHELDJOBS 3-30
LENVELOPEENHANCE 3-30 ✘ ✘ ✘
LENVELOPELENGTH 3-30 ✘ ✘ ✘
LENVELOPEOUTBIN 3-30 ✘ ✘ ✘
LENVELOPETEXTURE 3-31 ✘
LENVELOPEWEIGHT 3-31
LESCCHAR 3-31
LFAXRESOLUTION 3-31 ✘
LFAXREDIAL 3-31 ✘ ✘
LFAXREDIALFREQUENCY 3-31 ✘ ✘
LFAXTRANSMISSIONLOG 3-31 ✘ ✘
LFEEDERPAPERTYPE 3-31 ✘ ✘ ✘
LGLOSSYLOADING 3-31 ✘ ✘
LGLOSSYOUTPUTBIN 3-32 ✘ ✘ ✘
LGLOSSYTEXTURE 3-32 ✘ ✘ ✘
LGLOSSYWEIGHT 3-32 ✘ ✘ ✘
LHOLEPUNCHALARM 3-32 ✘ ✘ ✘
LHOLEPUNCHMODE 3-32 ✘ ✘ ✘

Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only. Default values are listed for exceptions only.
LIMAGEBRIGHTNESS 3-32 ✘ ✘
LIMAGECONTRAST 3-32 ✘ ✘
LIMAGEENHANCE 3-32 ✘
LIMAGEENHANCETYPE 3-33 ✘ 2
LIMAGEORIENTATION 3-33
LIMAGESMOOTHING 3-33 ✘ ✘
LINFEEDER ✘ ✘ ✘
LINFEEDERSIZE 3-33 ✘ ✘ ✘
LINKALERT 3-33 ✘ ✘ ✘
LINMPFEEDERSIZE 3-33
LJAMRECOVERY 3-33
LLABELSLENGTH 3-33 ✘ ✘ ✘
LLABELSLOADING 3-33 ✘
LLABELSOUTBIN 3-34 ✘ ✘ ✘
LLABELSTEXTURE 3-34 ✘
LLABELSWEIGHT 3-34
LLEFTMARGINOFFSET 3-34 ✘ ✘
LLETTERHEADLENGTH 3-34 ✘ ✘ ✘
LLETTERHEADLOADING 3-34 ✘
LLETTERHEADOUTBIN 3-35 ✘ ✘ ✘
LLETTERHEADTEXTURE 3-35 ✘
LLETTERHEADWEIGHT 3-35
LMANUALCOLORRGBTEXT 3-35 ✘ ✘
LMANUALCOLORRGBGRAPHICS 3-35 ✘ ✘
LMANUALCOLORRGBIMAGE 3-35 ✘ ✘
LMANUALCOLORCMYKTEXT 3-35 ✘ ✘
LMANUALCOLORCMYKGRAPHICS 3-35 ✘ ✘
LMANUALCOLORCMYKIMAGE 3-36 ✘ ✘

Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only. Default values are listed for exceptions only.
LMANUALENVELOPETYPE 3-36 ✘
LMANUALPAPERSIZE 3-36 ✘
LMANUALPAPERTYPE 3-36 ✘
LMAXSTATUSMSG ✘ ✘ ✘
LMPFEEDERPAPERTYPE 3-36 ✘ ✘
LMULTIPAGEBORDER 3-36
LMULTIPAGEORDER 3-36
LMULTIPAGEPRINT 3-37
LMULTIPAGEVIEW 3-37
LNPAP 3-37
LOPTIONALOUTBIN1NAME 3-37 ✘ ✘ ✘
LOPTIONALOUTBIN2NAME 3-37 ✘ ✘ ✘
LOPTIONALOUTBIN3NAME 3-37 ✘ ✘ ✘
LOPTIONALOUTBIN4NAME 3-37 ✘ ✘ ✘
LOPTIONALOUTBIN5NAME 3-37 ✘ ✘ ✘
LOPTIONALOUTBIN6NAME 3-38 ✘ ✘ ✘
LOPTIONALOUTBIN7NAME 3-38 ✘ ✘ ✘
LOPTIONALOUTBIN8NAME 3-38 ✘ ✘ ✘
LOPTIONALOUTBIN9NAME 3-38 ✘ ✘ ✘
LOPTIONALOUTBIN10NAME 3-38 ✘ ✘ ✘
LOUTBINCONFIG 3-38 ✘ ✘ ✘
LOVERFLOWOUTBIN 3-39 ✘ ✘ ✘
LOVERFLOWTIMER 3-39 ✘ ✘ ✘
LPAGECOUNT 3-39
LPAGEMODE 3-39
LPAPERSOURCE 3-39 TRAY1 TRAY1 TRAY1
LPICTUREGRADE 3-40 ✘
LPLAINLENGTH 3-40 ✘ ✘ ✘

Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only. Default values are listed for exceptions only.
LPLAINTEXTURE 3-40 ✘
LPLAINWEIGHT 3-40
LPOWERSAVER 3-40
LPPDS 3-41 ✘
LPPDSFORMLINES 3-41 ✘
LPPDSLINESPERINCH 3-41 ✘
LPREPRINTEDLENGTH 3-41 ✘ ✘ ✘
LPREPRINTEDLOADING 3-41 ✘
LPREPRINTEDOUTBIN 3-42 ✘ ✘ ✘
LPREPRINTEDTEXTURE 3-42 ✘
LPREPRINTEDWEIGHT 3-42
LPRINTBUFFER 3-42
LPRINTHEADIDLETIME 3-42 ✘ ✘ ✘
LPRINTERUSAGE 3-42 ✘ ✘ ✘
LPRINTMENUSBUTTON 3-42 ✘ ✘ ✘
LPRINTQUALITY 3-43 ✘ ✘ ✘
LPUNCH 3-43 ✘ ✘ ✘
LREAROUTBINNAME 3-43 ✘ ✘ ✘
LREPEATPRINTLIMIT 3-43 ✘
LRESET 3-43
LRESOURCESAVE 3-43
LRIGHTMARGINOFFSET 3-43 ✘
LSCREENING 3-43 ✘ ✘ ✘
LSEPARATORSHEETS 3-43
LSEPARATORSOURCE 3-43
LSTANDARDOUTBINNAME 3-44 ✘ ✘
LSTAPLE 3-44 ✘ ✘ ✘
LSTAPLESEMPTYALARM 3-44 ✘ ✘ ✘

Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only. Default values are listed for exceptions only.
LSTAPLETESTSOURCE 3-44 ✘ ✘ ✘
LSTROKEWIDTH 3-44 ✘ ✘ ✘
LSUBSTITUTESIZE 3-44 ALLLISTED ALLLISTED ALLLISTED
LTHINCOAT 3-44 ✘ ✘ ✘
LTOPBINROTATE 3-44 ✘ ✘ ✘
LTOPMARGINOFFSET 3-44 ✘ ✘ ✘
LTRANSPARENCYLENGTH 3-44 ✘ ✘ ✘
LTRANSPARENCYOUTBIN 3-45 ✘ ✘ ✘
LTRANSPARENCYTEXTURE 3-45 ✘
LTRANSPARENCYWEIGHT 3-45
LTRAY1SENSEDTYPEPAPER 3-45 ✘ ✘ ✘
LTRAY1SENSEDTYPETRANSPARENCY 3-45 ✘ ✘ ✘
LTRAY2SENSEDTYPEPAPER 3-45 ✘ ✘ ✘
LTRAY2SENSEDTYPETRANSPARENCY 3-45 ✘ ✘ ✘
LTRAY3SENSEDTYPEPAPER 3-46 ✘ ✘ ✘
LTRAY3SENSEDTYPETRANSPARENCY 3-46 ✘ ✘ ✘
LTRAY4SENSEDTYPEPAPER 3-46 ✘ ✘ ✘
LTRAY4SENSEDTYPETRANSPARENCY 3-46 ✘ ✘ ✘
LTRAY1AUTOSIZE 3-46 ✘ ✘
LTRAY2AUTOSIZE 3-46 ✘ ✘ ✘
LTRAY3AUTOSIZE 3-46 ✘ ✘ ✘
LTRAY4AUTOSIZE 3-46 ✘ ✘ ✘
LTRAY5AUTOSIZE 3-46 ✘ ✘ ✘
LTRAY1PAPERTYPE 3-46 PLAIN PLAIN PLAIN
LTRAY2PAPERTYPE 3-47 PLAIN or CUSTOMTYPE2
LTRAY4PAPERTYPE 3-47 ✘ ✘ ✘

Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only. Default values are listed for exceptions only.
LTRAY1RENUMBER 3-47
LTYPE1FONTS 3-47
LUSDEFAULTS 3-47
Table B-3: Common Variables for PCL Emulation
Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions.
FONTNUMBER 3-48
FONTSOURCE 3-48
PITCH 3-48
PTSIZE 3-48
SYMSET 3-48
Table B-4: Printer Unique Variables for PCL Emulation
Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions.
LA4WIDTH 3-49
LASSIGNFEEDER 3-49 ✘ ✘ ✘
LASSIGNMANUALENVELOPE 3-49 ✘
LASSIGNMANUALPAPER 3-49 ✘

Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions.
LASSIGNMPFEEDER 3-49 ✘ ✘
LASSIGNTRAY1 3-50
LASSIGNTRAY2 3-50
LASSIGNTRAY3 3-50 ✘ ✘ ✘
LASSIGNTRAY4 3-50 ✘ ✘ ✘
LASSIGNTRAY5 3-50 ✘ ✘ ✘
LBITMAPROUNDING 3-50
LCOLOREXTENSIONS 3-50
LFONTCOMPATIBILITY 3-51
LFONTPRIORITY 3-51
Table B-5: Common Variables for PostScript Emulation
Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions and
are listed for supported variables only.
PRTPSERRS 3-51
ADOBEMBT ✘ ✘ ✘
Table B-6: Printer Unique Variables for PostScript Emulation
Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions.
LPICTUREGRADE 3-52 ✘
LPSFONTPRIORITY 3-52

Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions.
LDESCRIPTION 3-53
LRWLOCK 3-53
LWLOCK 3-53
Table B-8: Status Readback Commands
Supported Printer Model
✘ Not Supported Page numbers reference command descriptions.
Dinquire 3-54
Echo 3-55
Info 3-56
Inquire 3-58
Ustatus 3-59
Ustatusoff 3-60
Supported Printer Model
✘ Not Supported Page numbers reference variable descriptions.
DEVICE 3-60
JOB 3-60
PAGE 3-60
TIMED 3-60

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code Return String
Intervention Required - PPDS Font Error
3-63 30014 50 PPDS Font Error ✘
Intervention Required - Insufficient Collation Area
3-63 30016 37 Insufficient Collation Area
Intervention Required - Insufficient Defragment Memory
3-63 30016 37 Insufficient Defrag Memory
Intervention Required - Insufficient Memory
3-63 30016 37 Insufficient Memory ✘ ✘
Intervention Required - Memory Full
3-63 30016 38 Memory Full
Intervention Required - Held Jobs May Not Be Restored
3-63 30016 Held Jobs May Not Be Restored ✘ ✘ ✘
Intervention Required - Configuration Change
3-63 30016 57 Configuration Change ✘ ✘ ✘
Intervention Required - Complex Page
3-63 30017 39 Complex Page
Intervention Required - Standard Serial Error
3-63 30018 54 Standard Serial Error ✘ ✘ ✘
Intervention Required - Serial Option Error
3-63 30018 54 Serial Option <slot #> error ✘ ✘
Intervention Required - Parallel Error
3-63 30018 54 Parallel Error ✘ ✘ ✘
Intervention Required - Network Software Error
3-65 30018 54 Std Network Software Error
Intervention Required - Standard Serial Fax Connection Lost
3-63 30018 54 Std Ser Fax Connection Lost ✘ ✘ ✘
Intervention Required - Standard Serial Disabled
3-63 30018 56 Standard Serial Disabled ✘ ✘ ✘
Intervention Required - Serial Option Disabled
3-64 30018 56 Serial <slot #> Port Disabled ✘ ✘ ✘
Intervention Required - Std Parallel Port Disabled
3-64 30018 56 Std Parallel Port Disabled ✘ ✘
Intervention Required - Parallel Port Disabled
3-64 30018 56 Parallel Port Disabled ✘ ✘ ✘
E330, E332n · C510(n) · E234(n),

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code Return String
Intervention Required - Parallel Port Error
3-64 30018 56 Parallel Port x Disabled ✘ ✘
Intervention Required - Standard USB Disabled
3-64 30018 56 Standard USB Port Disabled
Intervention Required - Resource Save Off Deficient Memory
3-64 30019 35 Res Save Off Deficient Memory
Intervention Required - Insufficient Fax Buffer
3-64 30026 55 Insufficient Fax Buffer ✘ ✘ ✘
Intervention Required - Std Par ENA Connection Lost
3-64 30027 54 Std Par ENA Connection Lost ✘ ✘
Intervention Required - Std Parallel Port Disabled
3-64 30027 56 Std Parallel Port Disabled ✘ ✘
Intervention Required - Resolution Reduced
3-64 30029 36 Resolution Reduced ✘ ✘ ✘
Intervention Required - Print Jobs on Disk Request
3-64 30031 Print Jobs on Disk? or Print Jobs on Disk. Go/Stop?
Intervention Required - Restore Held Jobs. Go/Stop?
3-64 30031 Restore Held Jobs. Go/Stop? ✘ ✘
Intervention Required - Short Paper
3-64 30034 34 Short Paper
Intervention Required - Flash Full
3-64 30035 52 Flash Full ✘ ✘ ✘
Intervention Required - Disk Full
3-64 30035 62 Disk Full ✘ ✘ ✘
Intervention Required - Defective Flash
3-64 30036 51 Defective Flash ✘ ✘ ✘
Intervention Required - Unformatted Flash
3-64 30036 53 Unformatted Flash ✘ ✘ ✘
Intervention Required - Defective Disk
3-64 30036 61 Defective Disk ✘ ✘ ✘
Intervention Required - Unformatted Disk
3-64 30036 63 Unformatted Disk ✘ ✘ ✘
Intervention Required - Scheduled Maintenance
3-65 30075 80 Scheduled Maintenance ✘
Intervention Required - Resource Save Off Deficient Memory
3-65 30076 35 Res Save Off Deficient Memory

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code Return String
Intervention Required - Insufficient Collation Area
3-65 30076 37 Insufficient Collation Area ✘ ✘ ✘
Intervention Required - Empty Hole Punch Box
3-65 30107 Empty Hole Punch Box ✘ ✘ ✘
Intervention Required - Empty Box M
3-65 30107 Empty Box M ✘ ✘ ✘
Intervention Required - Insert Box M
3-65 30107 Insert Box M ✘ ✘ ✘
Intervention Required - Insert Staple Cartridge
3-65 30107 Insert Staple Cartridge ✘ ✘ ✘
Intervention Required - Insert Stapler
3-65 30107 Insert Stapler ✘ ✘ ✘
Intervention Required - Priming Failed
3-65 30107 Priming Failed, Retry. Go/Stop? ✘ ✘ ✘
Intervention Required - Network x Software Error
3-65 30112 54 Network x Software Error ✘ ✘
Intervention Required - Serial Port x Disabled
3-65 30112 56 Serial Port x Disabled ✘ ✘
Intervention Required - Serial Option x Error
3-65 30112 54 Serial Option x Error ✘ ✘
Intervention Required - Serial x Fax Connection Lost
3-65 30112 54 Ser x Fax Connection Lost ✘ ✘ ✘
Intervention Required - USB Port Disabled
3-65 30112 56 USB Port x Disabled ✘ ✘
Intervention Required - Parallel x ENA Connection Lost
3-65 30113 54 Par x ENA Connection Lost ✘ ✘
Intervention Required - Parallel x Port Disabled
3-65 30113 56 Parallel Port x Disabled ✘ ✘
Intervention Required - Disk Operation Failed Jobs on Disk
3-65 32001 Operation Failed Jobs on Disk ✘ ✘ ✘
Intervention Required - Disk Operation Failed Faxes on Disk
3-65 32001 Operation Failed Faxes on Disk ✘ ✘ ✘
Intervention Required - Flash Full
3-65 32002 52 Flash Full
Intervention Required - Disk Full
3-66 32002 62 Disk Full ✘ ✘
E330, E332n · E234(n), · C510(n)

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code Return String
Intervention required: Disk Corrupted. Reformat?
3-66 32015 Disk Corrupted. Reformat? ✘ ✘
Intervention Required - Too Many Flash Options Installed
3-66 32030 58 Too Many Flash Options ✘ ✘
Intervention Required - Unformatted Flash
3-66 32052 53 Unformatted Flash
Intervention Required - Unformatted Disk
3-66 32052 63 Unformatted Disk ✘ ✘
3-66 32052 64 Unsupported Disk Format ✘ ✘
Intervention Required - Defective Flash
3-66 32056 51 Defective Flash
Intervention Required - Defective Disk
3-66 32056 61 Defective Disk ✘ ✘
Intervention Required - Scheduled Maintenance
3-66 35075 80 Scheduled Maintenance ✘ ✘ ✘
Intervention Required - Scheduled Maintenance
3-66 35075 81 Scheduled Maintenance ✘ ✘ ✘
Intervention Required - Fuser Maintenance
3-66 40038 80 Fuser Maintenance ✘ ✘ ✘
Intervention Required - Fuser Life Warning
3-66 40038 80 Fuser Life Warning ✘ ✘ ✘
Intervention Required - Belt Life Warning
3-66 40038 80 Belt Life Warning ✘ ✘ ✘
Intervention Required - Fuser/Belt Life Warning
3-66 40038 80 Fuser/Belt Life Warning ✘ ✘ ✘
Intervention Required - Fuser Exhausted
3-66 40038 80 Fuser Exhausted ✘ ✘ ✘
Intervention Required - Belt Exhausted
3-66 40038 80 Belt Exhausted ✘ ✘ ✘
Intervention Required - Fuser/Belt Exhausted
3-66 40038 80 Fuser/Belt Exhausted ✘ ✘ ✘
Intervention Required - ITU Maintenance
3-66 40038 83 ITU Maintenance ✘ ✘ ✘
E330, E332n · E234(n), · C510(n)

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code Return String
Intervention Required - 30 Coating Roll Missing 3-67 40010 30 Coating Roll Missing ✘ ✘ ✘
Intervention Required - 30 XXXX1 Print Unit Missing 3-67 40010 30 XXXX1 Print Unit Missing ✘ ✘ ✘
Intervention Required - Insert Hole Punch Box
3-67 40010 Insert Hole Punch Box ✘ ✘ ✘
Intervention Required - Insert PC Cartridge
3-67 40010 Insert PC Cartridge ✘ ✘ ✘
Intervention Required - Cartridge Life Expired
3-67 40021 Cartridge Life Expired XXXX1 ✘ ✘ ✘
3-68 40021 Cartridge Life Warning XXXX1 ✘ ✘ ✘
Intervention Required - Cartridge Life Warning
Intervention Required - Printer Upper Door Open
3-67 40021 Cover Open, Close Top Covers, Close Door, or Insert Cartridge
Intervention Required - Printer Cover Open
3-68 40021 Close Cover ✘ ✘ ✘
Intervention Required - Close Toner Box Cover
3-67 40021 Close Cover A ✘ ✘ ✘
Intervention Required - Close Deflector G
3-68 40021 Close Deflector G ✘ ✘ ✘
Intervention Required - Defective Print Cartridge
3-67 40021 31 Defective Print Cartridge ✘
3-67 40021 31 Defective Cartridge XXXX1 ✘ ✘ ✘
Intervention Required - Defective Ink Cartridge
Intervention Required - Missing Cartridge
3-68 40021 31 Missing Cartridge XXXX1 ✘ ✘ ✘
Intervention Required - Missing Printhead
3-68 40021 31 Missing Printhead ✘ ✘ ✘
Intervention Required - Unsupported Print Cartridge
3-67 40021 32 Unsupported Print Cartridge
Intervention Required - Unsupported XXXX1 Cartridge
3-67 40021 32 Unsupported XXXX1 Cartridge ✘ ✘ ✘
Intervention Required - Unsupported Cartridge
3-67 40021 32 Unsupported Cartridge ✘ ✘ ✘
1 XXXX represents a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code Return String
Intervention Required - Unsupported Printhead
3-68 40021 32 Unsupported Printhead ✘ ✘ ✘
Intervention Required - Tray Size Sense Error
3-68 40021 40 Tray x Size Sense Error ✘ ✘ ✘
Intervention Required - Open Bin Exit Tray
3-68 40021 41 Open Bin 1 Exit Tray ✘ ✘ ✘
Intervention Required - Change Cartridge Invalid Refill
3-67 40021 Change Cartridge Invalid Refill ✘
Intervention Required - Open Cover
3-68 40021 Open Cover ✘ ✘ ✘
Intervention Required - Open Rear Door
3-68 40021 Open Rear Door ✘ ✘ ✘
Intervention Required - Close Front Door
3-68 40021 Close Front Door ✘ ✘
Intervention Required - Close Side Door
3-68 40021 Close Side Door ✘ ✘ ✘
Intervention Required - Close Finisher Door
3-68 40021 Close Finisher Door ✘ ✘ ✘
Intervention Required - Close Finisher Side Door
3-68 40021 Close Finisher Side Door ✘ ✘ ✘
Intervention Required - Close Finisher Top Cover
3-68 40021 Close Finisher Top Cover ✘ ✘ ✘
Intervention Required - Close Door
3-68 40021 Close Door <d> ✘
Intervention Required - Close Cover
3-68 40021 Close Cover <c> ✘ ✘ ✘
Intervention Required - Close Tray x Top Cover
3-68 40021 Close Tray x Top Cover ✘ ✘ ✘
Intervention Required - Insert Print Cartridge
3-69 40021 Insert Print Cartridge ✘ ✘ ✘
Intervention Required - Paper Jam
3-69 40022 2xx Paper Jam ✘ ✘ ✘
Intervention Required - Check Tray Connection
3-69 40027 Check Tray <source #> Connection ✘ ✘ ✘
1 XXXX represents a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.
E330, E332n · E234(n), · C510(n)

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code Return String
Intervention Required - Install Tray x or Cancel Job
3-69 40027 Install Tray x or Cancel Job ✘ ✘ ✘
Intervention Required - Reattach Envelope Feeder
3-69 40028 Reattach Envelope Feeder ✘ ✘ ✘
Intervention Required - Install Env Feeder or Cancel Job
3-69 40028 Install Env Feed or Cancel Job ✘ ✘ ✘
Intervention Required - Reattach MP Feeder
3-69 40028 Reattach MP Feeder ✘ ✘ ✘
Intervention Required - Reattach Output Bin
3-69 40029 Reattach Output Bin <bin #> ✘ ✘ ✘
Intervention Required - Reattach Bins
3-69 40029 Reattach Bins <bin #x - bin #y> ✘ ✘ ✘
Intervention Required - Install Bin x or Cancel Job
3-69 40029 Install Bin x or Cancel Job ✘ ✘ ✘
Intervention Required - Check Finisher Installation
3-69 40029 Check Finisher Installation ✘ ✘ ✘
Intervention Required - Check Mailbox Installation
3-69 40029 Check Mailbox Installation ✘ ✘ ✘
Intervention Required - Tray Config Error
3-69 40030 33 Tray x Config Error ✘ ✘ ✘
Intervention Required - Input Config Error
3-69 40030 58 Input Config Error ✘ ✘ ✘
Intervention Required - Too Many Trays Attached
3-69 40030 58 Too Many Trays Attached ✘ ✘ ✘
Intervention Required - Too Many Bins Attached
3-69 40030 58 Too Many Bins Attached ✘ ✘ ✘
Intervention Required - Too Many Disks Installed
3-69 40030 58 Too Many Disks Installed ✘ ✘
Intervention Required - Too Many Disks Installed
3-69 40036 58 Too Many Disks Installed ✘ ✘ ✘
Intervention Required - PerfectFinish Missing
3-70 40037 31 PerfectFinish Missing ✘ ✘ ✘
Intervention Required - PerfectFinish Empty
3-70 40037 87 PerfectFinish Empty ✘ ✘ ✘
1 XXXX represents a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.
E330, E332n · E234(n), · C510(n)

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code Return String
Intervention Required - Toner Low
3-70 40038 88 Toner Low ✘
Intervention Required - Toner Low
3-70 40038 88 Yellow Toner Low
88 Magenta Toner Low
88 Cyan Toner Low
88 Black Toner Low
3-70 88 Color Print Cartridge Low
88 Black Print Cartridge Low
88 Photo Print Cartridge Low
3-70 88 Yellow Toner Empty
88 Magenta Toner Empty
88 Cyan Toner Empty
88 Black Toner Empty
Intervention Required - 84 Black Photo Dev Life Warning 3-70 40038 84 Black Photo Dev Life Warning ✘ ✘ ✘
Intervention Required - 84 Color Photo Dev Life Warning 3-70 40038 84 Color Photo Dev Life Warning ✘ ✘ ✘
Intervention Required - 84 All Photo Devs Exhausted 3-70 40038 84 All Photo Devs Exhausted ✘ ✘ ✘
Intervention Required - 84 Black Photo Dev Exhausted 3-70 40038 84 Black Photo Dev Exhausted ✘ ✘ ✘
Intervention Required - Cartridge Low
3-71 40038 88 Cartridge Low <CMYK>
Intervention Required - Replace PC Kit
3-71 40038 Replace PC Kit ✘ ✘ ✘
Intervention Required - Replace PC Kit To Continue
3-71 40038 Replace PC Kit To Continue ✘ ✘ ✘
Intervention Required - Replace Toner Cartridge
3-71 40038 Replace Toner Cartridge ✘ ✘ ✘
Intervention Required - Replace Toner Cartridge To Continue
3-71 40038 Replace Toner To Continue ✘ ✘ ✘
1 XXXX represents a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code Return String
Intervention Required - Replace Oil Coating Roll
3-71 40038 Replace Oil Coating Roll ✘ ✘ ✘
Intervention Required - Cartridge Empty
3-71 40039 89 Cartridge Empty <CMYK>
Intervention Required - Load Staples
3-71 40040 Load Staples ✘ ✘ ✘
Intervention Required - Priming Failed. Retry?
3-71 40041 Priming Failed. Retry? ✘ ✘ ✘
Intervention Required - OPMSG
3-71 40048 OPMSG message
Intervention Required - STMSG
3-71 40049 STMSG message
Intervention Required - Replace Fuser
3-71 40050 Replace Fuser ✘ ✘ ✘
Intervention Required - Replace Transfer Kit
3-71 40050 Replace Transfer Kit ✘ ✘ ✘
Intervention Required - Incompatible Bin x
3-71 40087 59 Incompatible Bin x ✘ ✘ ✘
Intervention Required - Incompatible Duplex
3-71 40088 59 Incompatible Duplex ✘ ✘ ✘
Intervention Required - Incompatible Tray x
3-71 40089 59 Incompatible Tray x ✘ ✘ ✘
Intervention Required - Incompatible Envelope Feeder
3-71 40090 59 Incompatible Envelope Feeder ✘ ✘ ✘
Intervention Required - Check Duplex Connection
3-71 40095 Check Duplex Connection ✘ ✘ ✘
Intervention Required - Install Duplex or Cancel Job
3-72 40095 Install Duplex or Cancel Job ✘ ✘ ✘
Intervention Required - Duplex Cover Open
3-72 40096 Close Duplex Door ✘ ✘
Intervention Required - Insert Duplex Option
3-72 40096 Insert Duplex Option ✘ ✘ ✘
Intervention Required - Load Staples
3-72 40101 Load Staples ✘ ✘ ✘
1 XXXX represents a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code Return String*
Intervention Required - Wrong Paper Size in Tray x
3-73 30034 34 Wrong Paper Size in Tray x ✘ ✘ ✘
Intervention Required - Wrong Paper Size Manual Feed
3-73 30034 34 Wrong Paper Size Manual Feed ✘ ✘ ✘
Intervention Required - Remove Paper Standard Bin
3-73 40019 Remove Paper Standard Bin
Intervention Required - Remove Paper Outbin
3-73 40019 Remove Paper Output Bin <bin #> ✘ ✘ ✘
Intervention Required - Remove Paper All Output Bins
3-73 40019 Remove Paper All Output Bins ✘ ✘ ✘
Intervention Required - Remove Paper
3-73 40019 Remove Paper <linked set bin name>
Intervention Required - Check Paper Guide
3-73 4100x Check <source> Paper Guide ✘ ✘ ✘
Intervention Required - Incorrect Media
3-73 41xyy 34 Incorrect Media ✘ ✘ ✘
Intervention Required - Load Request
3-73 41xyy Load <source> <Custom Type Name> <Custom String> <size> <type> <size>
Intervention Required - Load Manual Request
3-73 41xxy Load Manual <Custom Type Name> <Custom String> <size> <type> <size>
Intervention Required - Change Request
3-73 41xyy Change <source> <Custom Type Name> <Custom String> <size> <type> <size>
x represents an input source code. For more information, see “Table 3-16: Tray Codes” on page 3-74. yy represents a media size code. For more information, see “Table 3-17: Media Size Codes” on page 3-74. * Refer to your printer user documentation for return string messages.

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code Return String*
Intervention Required - Insert Duplex Pages & Press Go.
3-73 412yy Insert Duplex Pages & Press Go. ✘ ✘ ✘
Intervention Required - Insert Tray Request
3-73 4300x Insert Tray <source #>
x represents an input source code. For more information, see “Table 3-16: Tray Codes” on page 3-74. yy represents a media size code. For more information, see “Table 3-17: Media Size Codes” on page 3-74. * Refer to your printer user documentation for return string messages.
Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code
Intervention Required - Paper Jam
3-76 4200x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4201x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4202x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4203x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4204x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4205x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4206x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4207x ✘ ✘ ✘
w indicates this message includes a letter indicating a door or cover. The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number.

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code
Intervention Required - Paper Jam
3-76 4208x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4209x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4210x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4211x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4220x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4221x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4222x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4230x ✘ ✘ ✘
Intervention Required - Paper Jam
3-76 4231x ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4232x ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4233x ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4234 ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 424yx ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4241wy ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4242wy ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4243w ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4244wy ✘ ✘ ✘
w indicates this message includes a letter indicating a door or cover. The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number.
E330, E332n · E234(n), · C510(n)

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code
Intervention Required - Paper Jam
3-77 4245w ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4246w ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4247wy ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4248w ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4249w ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4250w ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4250x ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4251wy ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4251x ✘ ✘ ✘
Intervention Required - Paper Jam
3-77 4252w ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4253w ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4254wy ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4255 ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4256w ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4257w ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4258w ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4259wy ✘ ✘ ✘
w indicates this message includes a letter indicating a door or cover. The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number.
E330, E332n · E234(n), · C510(n)

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code
Intervention Required - Paper Jam
3-78 4260w ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4260x ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4261w ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4261x ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 427zx ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4271 ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4272 ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4273 ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4280w ✘ ✘ ✘
Intervention Required - Paper Jam
3-78 4280x ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4281w ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4281x ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4282w ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4282x ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4283w ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4283x ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4284w ✘ ✘ ✘
w indicates this message includes a letter indicating a door or cover. The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number.
E330, E332n · E234(n), · C510(n)

Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
Message Page Status Code
Intervention Required - Paper Jam
3-79 4284x ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4285w ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4286w ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4287 ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4288 ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4289 ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4290 ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4291 ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4292 ✘ ✘ ✘
Intervention Required - Paper Jam
3-79 4293 ✘ ✘ ✘
Intervention Required - Paper Jam
3-80 4294 ✘ ✘ ✘
Intervention Required - Paper Jam
3-80 4295 ✘ ✘ ✘
w indicates this message includes a letter indicating a door or cover. The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number.
E330, E332n · E234(n), · C510(n)

Supported Printer Model
✘ Not Supported Page numbers reference message description.
Message Page Error Code
Table B-15: Device Attendance Messages
Supported Printer Model
✘ Not Supported Page numbers reference message descriptions.
RDYMSG 3-80
OPMSG 3-81
STMSG 3-81
Table B-16: Lexmark Unique PJL Commands
Supported Printer Model
✘ Not Supported Page numbers reference command descriptions.
LBEEP 3-82
LDOWNLOADTARGET 3-30
LPORTROTATE 3-82
LPRINT testpage 3-83

Supported Printer Model
✘ Not Supported Page numbers reference command descriptions.
LFAX PHONENUMBER 3-85
LOPENFILE 3-89
LCLOSEFILE 3-89
LREADFILE 3-90
LWRITEFILE 3-91
LRUNFILE 3-91
LRENAMEFILE 3-92
LDELETEFILE 3-92
LFORMAT 3-92
LDEFRAG 3-92
Table B-17: File and Device Protection Commands
Supported Printer Model
✘ Not Supported Page numbers reference command descriptions.
LDECLARE LRESOURCE 3-95
LDELETEPASSWORD 3-96
LQUERYSEED LBYPASSPASSWORD KEY
3-98

APPENDIX C: PostScript Support
The following tables list PostScript commands and identify printers that support them.
For detailed information about PostScript emulation, see “PostScript Emulation” on page 4-1.
Supported Printer Model
✘ Not Supported Page numbers reference operator descriptions.
appletalktype 4-27
buildtime 4-27
byteorder 4-27
checkpassword 4-28
currentfilenameextend 4-28
currentmanualduplexmode 4-28 ✘ ✘ ✘
currentuniversalsize 4-17
defaulttimeouts 4-29
deletefile 4-29
devcontrol 4-30
devdismount 4-31
devforall 4-32
devformat 4-32
devmount 4-33
devstatus 4-33
diskonline 4-34
diskstatus 4-35
displayoperatormsg 4-35
doidlefonts 4-35
dojamrecovery 4-36
doprinterrors 4-36
doret 4-36

Supported Printer Model
✘ Not Supported Page numbers reference operator descriptions.
dostartpage 4-37
dosysstart 4-37
duplexer 4-37
duplexmode 4-38
enginesync 4-38
file 4-39
filenameforall 4-39
fileposition 4-39
firstside 4-40
fontnonzerowinding 4-40
hardwareiomode 4-40
idlefonts 4-40
ignoresize 4-17
initializedisk 4-41
jobname 4-41
jobsource 4-42
jobtimeout 4-43
manualfeed 4-21
manualfeedtimeout 4-44
newsheet 4-44
pagecount 4-44
pagesprinted 4-45
papertray 4-21
printername 4-45
product 4-45
PS2fonts 4-46
PS3fonts 4-46
quiet 4-46
ramsize 4-47
realformat 4-47
renamefile 4-47

Supported Printer Model
✘ Not Supported Page numbers reference operator descriptions.
resolution 4-48
revision 4-48
sccbatch 4-49
sccinteractive 4-50
setcoverpage 4-50
setdefaulttimeouts 4-50
setdoidlefonts 4-51
setdojamrecovery 4-51
setdoprinterrors 4-51
setdoret 4-52
setdostartpage 4-52
setdosysstart 4-53
setduplexmode 4-53
setenginesync 4-54
setethernetaddress 4-54
setfilenameextend 4-54
setfileposition 4-55
sethardwareiomode 4-55
setidlefonts 4-55
setignoresize 4-17
setjobtimeout 4-56
setmanualduplexmode 4-56 ✘ ✘
setpapertray 4-22
setprintername 4-57
setquiet 4-57
setresolution 4-58
setsccbatch 4-58
setsccinteractive 4-59
setsoftwareiomode 4-59
settumble 4-59
setuniversalsize 4-18

Supported Printer Model
✘ Not Supported Page numbers reference operator descriptions.
setuserdiskpercent 4-60
softwareiomode 4-60
tumble 4-60
userdiskpercent 4-61
waittimeout 4-61
Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions. Default values are listed.
BeginPage 4-62
Collate 4-62 false false true
DeferredMediaSelection 4-62 false false false
DeviceRenderingInfo 4-62
– ColorGrade 4-62 ✘ ✘ ✘
– PictureGrade 4-62 ✘
– IETImagesOnly 4-62 ✘ ✘ ✘
– IETPictureGrade 4-62 ✘
– None 4-62 ✘

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions. Default values are listed.
Duplex 4-65
EndPage 4-65
ExitJamRecovery 4-65
HWResolution 4-65
ImagingBBox 4-66
InputAttributes 4-66
– PageSize 4-66
– MatchAll 4-66
– MediaColor 4-66
– MediaType 4-66
– MediaWeight 4-66
– InputLocation 4-66
Install 4-67
Jog 4-67 ✘ ✘ ✘
ManualFeed 4-68
ManualFeedTimeout 4-68

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions. Default values are listed.
MediaColor 4-68
MediaPosition 4-68 null null null
MediaType 4-68
MediaWeight 4-68
NumCopies 4-68
Nup 4-68
NupDetails 4-69
OutputAttributes 4-71
– OutputType 4-71
– OutputLocation 4-71
OutputPage 4-71 true true true
OutputType 4-71
PageDeviceName 4-71

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions. Default values are listed.
PageSize 4-72
Policies 4-72
PostRenderingEnhance 4-72 ✘ true true
PostRenderingEnhanceDetails 4-73 ✘
PowerSave 4-73 20 20 20
ProcessColorModel 4-73 ✘ ✘
Punch 4-73 ✘ ✘ ✘
SlipSheet 4-73 ✘ ✘
SlipSheetDetails 4-74
Staple 4-74 ✘ ✘ ✘
TraySwitch 4-74
Tumble 4-75
UniversalDetails 4-75

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions.
AccurateScreens 4-76 false
CollatedCopies 4-76 Collation - Collated Copies (QTY) value
HalftoneMode 4-77 0
IdiomRecognition 4-77 true
JobName 4-77 ( )
JobTimeout 4-77 JobTimeout system parameter
MaxDictStack 4-77 255
MaxExecStack 4-77 10015
MaxFontItem 4-77 12500
MaxFormItem 4-77 100000
MaxLocalVM 4-77 2147483647
MaxOpStack 4-78 100000
MaxPatternItem 4-78 20000
MaxScreenItem 4-78 48000
MaxSuperScreen 4-78 1024
MaxUPathItem 4-78 5000
MinFontCompress 4-78 2147483647
PageCount 4-78 0
UseOldcopypage 4-78 false
VMReclaim 4-78 0
VMThreshold 4-78 25000 per MB of RAM
WaitTimeout 4-78 WaitTimeout system parameter

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions. Default values are listed.
BuildTime 4-79
ByteOrder 4-79 false false false
CurDisplayList 4-79 0 0 0
CurFontCache 4-79 0 0 0
CurFormCache 4-79 0 0 0
CurInputDevice 4-80
CurOutlineCache 4-80
CurOutputDevice 4-80
CurPatternCache 4-80
CurScreenStorage 4-80
CurSourceList 4-80
CurUPathCache 4-80
DisableFastProcs 4-80
DoPrintErrors 4-81 Initialized from the Print PS Error
DoStartPage 4-81 false false false
EnableExtraFonts 4-81 true true true
EngineBoot 4-81
EngineCode 4-81
EngineSpeed 4-81
FactoryDefaults 4-81 false false false
FatalErrorAddress 4-81 0 0 0
FontResourceDir 4-81 (fonts/) (fonts/) (fonts/)
FontVersion 4-81
GenericResourcePathSep 4-81 (/) (/) (/)
InstalledRam 4-82
JobTimeout 4-82 Initialized from the Job Timeout menu item

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions. Default values are listed.
languagelevel 4-82 3 3 3
MaxFormCache 4-82 101000 101000 101000
MaxPatternCache 4-82 101000 101000 101000
MaxUPathCache 4-83 301000 301000 301000
PageCount 4-83 Initialized from the Page Count menu item
PanelCode 4-83
PrinterCode 4-83
PrinterName 4-83
RamSize 4-83
RealFormat 4-83 (IEEE) (IEEE) (IEEE)
Revision 4-83
SearchBuiltinFontsFirst 4-83 true true true
SerialNumber 4-83
StartJobPassword 4-83 ( ) ( ) ( )
StartupMode 4-83 1 1 1
StaticRamSize 4-83
SystemParamsPassword 4-84 ( ) ( ) ( )
UseOldcopypage 4-84 false false false
UseOldfonts 4-84 false false false
ValidNV 4-84 true true true
WaitTimeout 4-78 Initialized from the Wait Timeout menu

Supported ✘ Not Supported n Network version of the printer model
E232
E234
E330
%ParallelA% 4-79 ✘ ✘
%ParallelB% ✘
%ParallelC% ✘
%ParallelD% ✘
%SerialA% ✘ ✘ ✘
%SerialB% ✘
%SerialC% ✘
%SerialD% ✘
%LocalTalkA% ✘
%LocalTalkB% ✘
%LocalTalkC% ✘
%LocalTalkD% ✘
%EtherTalkA% ✘
%EtherTalkB% ✘
%EtherTalkC% ✘
%EtherTalkD% ✘
%IR_A% ✘
%IR_B% ✘
%IR_C% ✘
%IR_D% ✘
%USB_A%
%USB_B% ✘
%USB_C% ✘
%USB_D% ✘
%TokenTalkA% ✘
%TokenTalkB% ✘
%TokenTalkC% ✘
%TokenTalkD% ✘
%AppSocketA% ✘
%AppSocketB% ✘

Supported ✘ Not Supported n Network version of the printer model
E232
E234
E330
%AppSocketC% 4-79 ✘
%AppSocketD% ✘
%RemotePrinterA% ✘
%RemotePrinterB% ✘
%RemotePrinterC% ✘
%RemotePrinterD% ✘
%PrintServerA% ✘
%PrintServerB% ✘
%PrintServerC% ✘
%PrintServerD% ✘
%LPR_A% ✘
%LPR_B% ✘
%LPR_C% ✘
%LPR_D% ✘
%LexLinkA% ✘
%LexLinkB% ✘
%LexLinkC% ✘
%LexLinkD% ✘
%IP_A% ✘
%IP_B% ✘
%IP_C% ✘
%IP_D% ✘
%EthernetPhysicalA% ✘
%EthernetPhysicalB% ✘
%EthernetPhysicalC% ✘
%EthernetPhysicalD% ✘
%TokenRingPhysicalA% ✘
%TokenRingPhysicalB% ✘
%TokenRingPhysicalC% ✘
%TokenRingPhysicalD% ✘

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions.
E330, E332
Device Parameters for the Communication Device %Parallel%, %ParallelA%, %ParallelB%, %ParallelC%, %ParallelD%
DelayedOutputClose 4-86
Enabled 4-86
Filtering 4-86
Handshake 4-86
HasNames 4-86
Interpreter 4-86
On 4-86
OutputDevice 4-86
PCLSmartSwitch 4-86
PortLocation 4-86
PSSmartSwitch 4-87
Type 4-87
Device Parameters for the Communication Device %Serial%, %SerialA%, %SerialB%, %SerialC%, %SerialD%
Baud 4-87
CheckParity 4-87
DataBits 4-87
DelayedOutputClose 4-87
Enabled 4-87
Filtering 4-87
FlowControl 4-87
HasNames 4-87
HonorDSR 4-87
Interpreter 4-88
On 4-88
Parity 4-88
PCLSmartSwitch 4-88
PortLocation 4-88
E234(n), · C510(n) · Key Page

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions.
E330, E332
PSSmartSwitch 4-88
RobustXon 4-88
SerialMode 4-88
StopBits 4-89
Type 4-89
Device Parameters for the Communication Device %LocalTalk%, %LocalTalkA%, %LocalTalkB%, %LocalTalkC%, %LocalTalkD%
DelayedOutputClose 4-89
Enabled 4-89
Filtering 4-89
HasNames 4-89
Interpreter 4-89
LocalTalkType 4-89
NodeID 4-89
On 4-89
PCLSmartSwitch 4-90
PortLocation 4-90
PSSmartSwitch 4-90
Type 4-90
Device Parameters for the Communication Device %EtherTalk%, %EtherTalkA%, %EtherTalkB%, %EtherTalkC%, %EtherTalkD%
DelayedOutputClose 4-90
Enabled 4-90
EthernetAddress 4-90
EtherTalkType 4-90
EtherTalkZone 4-90
Filtering 4-91
HasNames 4-91
Interpreter 4-91
NodeID 4-91
On 4-91
PCLSmartSwitch 4-91
E234(n), · C510(n) · Key Page

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions.
E330, E332
PortLocation 4-91
PSSmartSwitch 4-91
Type 4-91
Device Parameters for the Communication Device %IR%, %IR_A%, %IR_B%, %IR_C%, %IR_D%
DelayedOutputClose 4-91
Enabled 4-92
Filtering 4-92
HasNames 4-92
Interpreter 4-92
On 4-92
PCLSmartSwitch 4-92
PortLocation 4-92
PSSmartSwitch 4-92
Type 4-92
Device Parameters for the Communication Device %USB%, %USB_A%, %USB_B%, %USB_C%, %USB_D%
DelayedOutputClose 4-92
Enabled 4-93
Filtering 4-93
HasNames 4-93
Interpreter 4-93
On 4-93
PCLSmartSwitch 4-93
PortLocation 4-93
PSSmartSwitch 4-93
Type 4-93
Device Parameters for the Communication Device %TokenTalk%, %TokenTalkA%, %TokenTalkB%, %TokenTalkC%, %TokenTalkD%
Address 4-93
Bridging 4-93
DelayedOutputClose 4-94
Enabled 4-94
E234(n), · C510(n) · Key Page

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions.
E330, E332
Filtering 4-94
HasNames 4-94
Interpreter 4-94
NodeID 4-94
On 4-94
PCLSmartSwitch 4-94
PortLocation 4-94
PSSmartSwitch 4-94
TokenTalkType 4-95
Type 4-95
Zone 4-95 ✘ ✘ ✘
E234(n), · C510(n) · Key Page

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions.
E330, E332
Device Parameters for the Communication Device %AppSocket%, %AppSocketA%, %AppSocketB%, %AppSocketC%, %AppSocketD%
DelayedOutputClose 4-95
Enabled 4-95
Filtering 4-95
HasNames 4-95
Interpreter 4-95
On 4-95
PortLocation 4-95
Type 4-95
Device Parameters for the Communication Device %RemotePrinter%, %RemotePrinterA%, %RemotePrinterB%, %RemotePrinterC%, %RemotePrinterD%
DelayedOutputClose 4-96
Enabled 4-96
Filtering 4-96
HasNames 4-96
Interpreter 4-96
On 4-96
PortLocation 4-96
Type 4-96
Device Parameters for the Communication Device %PrintServer%, PrintServerA%, PrintServerB%, %PrintServerC%, %PrintServerD%
DelayedOutputClose 4-97
Enabled 4-97
Filtering 4-97
HasNames 4-97
Interpreter 4-97
On 4-97
PortLocation 4-97
Type 4-97
E234(n), · C510(n) · Key Page

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions.
E330, E332
Device Parameters for the Communication Device %LPR%, %LPR_A%, %LPR_B%, %LPR_C%, %LPR_D%
Enabled 4-98
Filtering 4-98
HasNames 4-98
Interpreter 4-98
On 4-98
PortLocation 4-98
Type 4-98
Device Parameters for the Communication Device %LexLink%, %LexLinkA%, %LexLinkB%, %LexLinkC%, %LexLinkD%
DelayedOutputClose 4-98
Enabled 4-98
HasNames 4-99
Interpreter 4-99
On 4-99
PortLocation 4-99
Type 4-99
Device Parameters for the Communication Device %IP%, %IP_A%, %IP_B%, %IP_C%, %IP_D%
GatewayAddress 4-99
IPAddress 4-99
IPAddressDynamic 4-99
NetworkMask 4-99
On 4-99
Physical 4-99
PortLocation 4-99
Type 4-99
Device Parameters for the Communication Device %EthernetPhysical%, %EthernetPhysicalA%, %EthernetPhysicalB%, %EthernetPhysicalC%, %EthernetPhysicalD%
EthernetAddress 4-100
On 4-100
PortLocation 4-100
Type 4-100
E234(n), · C510(n) · Key Page

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions.
E330, E332
Device Parameters for the Communication Device %TokenRingPhysical%, %TokenRingPhysicalA%, %TokenRingPhysicalB%, %TokenRingPhysicalC%, %TokenRingPhysicalD%
Address 4-100
On 4-100
PortLocation 4-100
Speed 4-100
Type 4-100
Device Parameters for the Parameters Device %Engine%
BSizeStandard 4-100
Darkness 4-101
PageCount 4-102
TimeToStandby 4-102
Type 4-102
Device Parameters for the Parameters Device %Console%
Language 4-102
Type 4-102
Device Parameters for the Parameters Device %Calendar%, %CalendarA%, %CalendarB%, %CalendarC%, %CalendarD%
Day 4-102
Hour 4-102
Minute 4-102
Month 4-102
Running 4-102
Second 4-102
Type 4-102
Year 4-102
DateTime 4-102
DayOfWeekLong 4-102
DayOfWeekNum 4-102
DayOfWeekShort 4-102
E234(n), · C510(n) · Key Page

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions.
E330, E332
Device Parameters for the Parameters Device %disk1%
BlockSize 4-102
Free 4-102
HasNames 4-102
InitializeAction 4-103
LogicalSize 4-103
Mounted 4-103
PhysicalSize 4-103
Removable 4-103
Searchable 4-103
SearchOrder 4-103
Type 4-103
Writeable 4-103
Device Parameters for the Parameters Device %flash1%
BlockSize 4-103
Free 4-103
HasNames 4-104
InitializeAction 4-104
LogicalSize 4-104
Mounted 4-104
PhysicalSize 4-104
Removable 4-104
Searchable 4-104
SearchOrder 4-104
Type 4-104
Writeable 4-104
E234(n), · C510(n) · Key Page

Supported Printer Model
✘ Not Supported Page numbers reference parameter descriptions.
E330, E332
Device Parameters for the Parameters Device %rom%
BlockSize 4-105
Free 4-105
HasNames 4-105
InitializeAction 4-105
LogicalSize 4-105
Mounted 4-105
PhysicalSize 4-105
Removable 4-105
Searchable 4-105
SearchOrder 4-105
Type 4-105
Writeable 4-105
Supported Printer Model
✘ Not Supported Page numbers reference status message key and
E330, E332
value descriptions.
job 4-107
status 4-107
source 4-107

color extensions 2-80 cursor positioning 2-68 font creation 2-73 font selection 2-70 job control 2-62 macros 2-73 miscellaneous commands 2-83 page control 2-64 picture frame 2-83 print model 2-74 raster graphics 2-77 rectangular area fill graphics 2-75 status readback 2-82 user-defined pattern 2-75 user-defined symbol set 2-72 external network adapter
rewriting contents 6-8 storing fonts, macros, and symbol sets 6-2 viewing the contents 6-3 fonts
Lexmark C510(n) 2-19 Lexmark E321 2-29 Lexmark X422 2-9, 2-37 printing directory list for flash or disk 3-83, 6-3 saving on flash memory or disk 6-3 selecting
MarkVision Professional 2-9, 2-19 setting password protection 3-93 formatting flash or disk, PJL 3-92
See external print server external print server
MarkNet Pro 8-42 MarkNet XLe 8-42
character group 2-86 configuration group 2-84 line and fill attributes group 2-87 polygon group 2-85 vector group 2-85
fastbytes protocol 8-16 file (flash memory or disk)
close 3-89 delete 3-92 format device 3-92 open 3-89 read 3-90 rename 3-92 run 3-91 write 3-91 filenames
See disk hardware specifications 7-1, 8-1 Honor DSR setting 8-32
file types 6-6 filename parameter (PJL) 3-88 macros, font, and symbol set ID 6-5 PostScript emulation conventions 6-9 searching 6-12 fit to page printing 2-7, 2-8 flash memory
status messages (PJL) 3-61 input buffer 8-43 interface
parallel 8-7 selecting 8-6 serial 8-25 SmartSwitch 5-2 internal network adapter
description 6-1 directory of contents 6-4 download target (PJL) 3-30 password protection 6-7 performance 6-13 Resource Data Collection mode 6-2 retrieval speed 6-13
See internal print server internal print server

J
N
network support 8-42 noise emission levels 7-1 nonprintable areas 2-7 notation, commands
creating a partition 6-14 disabling 6-15 enabling 6-14 recovering from a power loss 6-15
PCL emulation 2-59 PostScript emulation 4-14 Printer Job Language (PJL) 3-1
MarkVision Professional 2-1 operator panel 2-1 software program 2-2 PostScript emulation 4-1
OCR fonts 2-10, 2-20 operator intervention
status messages (PJL) 3-72, 3-75 output bins
operator panel 4-1 software program 4-2 Printer Job Language (PJL) 3-3 setting for different interfaces 5-2 SmartSwitch 5-1 link buffer 8-43 logical page
status message codes 3-75
PCL emulation 2-3 PostScript emulation 4-3 paper handling 3-72 paper sizes
PCL emulation 2-3, 2-7 PostScript emulation 4-3, 4-4
status message codes 3-74 paper sizes supported
Lexmark C510(n) 2-4, 2-6 Lexmark X422 2-5 paper trays
flash memory or disk 6-3 setting password protection 3-93 storing on flash memory or disk 6-3 MarkNet Pro external print server 8-42 MarkNet S internal print server 8-42 MarkNet XLe external print server 8-42 MarkVision Professional
paper size 2-64 paper source 2-64 PostScript emulation
automatic size sensing search order 4-18 operators 4-20 Printer Job Language (PJL)
job buffering 6-13 passwords 6-8 Resource Data Collection mode 6-2 viewing contents of flash memory and disk 6-3 media sizes
paper size 3-14 paper source 3-39 status message codes 3-74 parallel interface 8-7
connector pin assignments 8-8 optional connector 8-8 signal descriptions 8-19 standard connector 8-8 parallel modes 8-18 parameters, PostScript emulation
status message codes 3-74 menus, printing settings from PJL 3-83 multipurpose feeder
PCL emulation 2-64 Printer Job Language (PJL) 3-39

device 4-85 system 4-79 user 4-76 page device 4-62 password 6-7
horizontal (columns) 2-68 horizontal (decipoints) 2-68 horizontal (PCL units) 2-68 line termination 2-69 push/pop cursor position 2-69 vertical (decipoints) 2-69 vertical (PCL units) 2-69 vertical (rows) 2-69 font creation
directory of flash memory or disk 6-6 general notes 3-93 locking entire flash or disk 3-94 lost file or device password 3-98 read/write protection 6-7 relocking file or device 3-96 setting job password 3-5, 3-6 setting password for a file 3-93 unlocking file or device for current job 3-97 unlocking protection for flash or disk 3-95 write protection 6-7 PCL emulation
character code 2-73 font control 2-73 font descriptor 2-73 font ID 2-73 load character 2-73 font selection
height (primary) 2-70 height (secondary) 2-70 pitch (primary) 2-70 pitch (secondary) 2-70 primary and secondary pitch 2-72 select default font (primary) 2-71 select default font (secondary) 2-71 select download font (primary) 2-71 select download font (secondary) 2-71 spacing (primary) 2-70 spacing (secondary) 2-70 stroke weight (primary) 2-71 stroke weight (secondary) 2-71 style (primary) 2-70 style (secondary) 2-70 symbol set (primary) 2-70 symbol set (secondary) 2-70 text parsing method 2-72 transparent print data 2-71 typeface selection (primary) 2-71 typeface selection (secondary) 2-71 underline disable 2-71 underline enable 2-71 job control
command structure 2-29, 2-60
control codes 2-59 escape control code 2-59 linking commands 2-61 parameters 2-60 relative positioning 2-61 syntax 2-60 commands
alphabetic 2-62 alphanumeric ID 2-68 color extensions
assign color index 2-81 color component one 2-81 color component three 2-81 color component two 2-81 color lookup tables 2-80 configure image data 2-81 driver configuration command 2-80 foreground color 2-81 gamma correction 2-81 monochrome print mode 2-80 palette control 2-80 palette ID 2-80 push/pop palette 2-80 render algorithm 2-81 select palette by ID 2-80 simple color 2-80 user-defined dither matrix 2-80 viewing illuminant 2-81 cursor positioning
job separation 2-65 long-edge offset registration 2-62 number of collated copies 2-62 number of copies 2-62 output bin 2-66 printer reset 2-62 short-edge offset registration 2-62 simplex/duplex print 2-62 unit of measure 2-63
half line-feed 2-69

Universal Exit Language 2-63 macros
set pattern reference point 2-75 source transparency mode 2-74 user-defined pattern 2-75 raster graphics
macro control 2-73 macro ID 2-73 miscellaneous commands
destination raster height 2-79 destination raster width 2-78 end raster graphics (version B) 2-78 end raster graphics (version C) 2-78 raster graphics presentation 2-77 raster resolution 2-77 set raster compression mode 2-78 set raster configuration 2-79 source raster height 2-77 source raster width 2-77 start raster graphics 2-77 transfer raster data by plane 2-77 transfer raster data by row/block 2-78 Y offset 2-77 rectangular area fill graphics
display functions off 2-84 display functions on 2-83 end-of-line wrap 2-83 paper type 2-84 print quality 2-84 print test page 2-84 page control
character text path 2-65 clear horizontal margins 2-65 duplex page side selection 2-67 horizontal motion index 2-66 left margin 2-65 line spacing (alternative method) 2-67 page orientation 2-65 page size 2-64 paper source 2-64 print direction 2-65 right margin 2-65 set page length 2-67 set universal custom name 2-65 set universal feed direction 2-65 set universal height 2-64 set universal width 2-64 skip perforation 2-66 text length 2-66 text scale mode 2-67 top margin 2-65 vertical motion index 2-66 picture frame
area fill ID 2-76 fill rectangular area 2-76 horizontal rectangle size 2-75 vertical rectangle size (decipoints) 2-75 vertical rectangle size (PCL Units) 2-75 status readback
echo 2-82 flush all pages 2-82 free space 2-82 inquire status readback entity 2-82 set status readback location type 2-82 set status readback location unit 2-82 user-defined symbol set
define symbol set 2-72 symbol set control 2-72 symbol set ID code 2-72 control codes 2-59 font and symbol set support
enter GL/2 language 2-83 enter PCL emulation 2-83 GL/2 plot horizontal size 2-83 GL/2 plot vertical size 2-83 picture frame horizontal size 2-83 picture frame vertical size 2-83 set picture frame anchor point 2-83 print model
Lexmark C510(n) 2-19 Lexmark E321 2-29 Lexmark X422 2-9, 2-37 GL/2 Language 2-84 linking commands 2-60 paper and envelope dimensions
area fill ID 2-74 logical operation 2-74 pattern control 2-75 pattern transparency mode 2-74 pixel placement 2-74 select current pattern 2-74
Lexmark C510(n) 2-4, 2-6 Lexmark X422 2-5 password protection 3-93 saving files on flash memory or disk 6-3 selecting

MarkVision Professional 2-1 operator panel 2-1 SmartSwitch 2-1 software program 2-2 SmartSwitch 2-1 specialty fonts 2-31, 2-42 standard fonts 2-10, 2-20, 2-30, 2-38 Type 1 fonts 2-13, 2-23, 2-40 variables, PJL
Type 1 fonts on flash memory or disk 3-93 printable areas 4-3 saving fonts on flash memory or disk 6-3 selecting language 4-1 SmartSwitch 4-1 status and error messages 4-106, 4-107 supplemental operators 4-27
appletalktype 4-27 buildtime 4-27 byteorder 4-27 checkpassword 4-28 currentfilenameextend 4-28 currentmanualduplexmode 4-28 defaulttimeouts 4-29 deletefile 4-29 devcontrol 4-30 devdismount 4-31 devforall 4-32 devformat 4-32 devmount 4-33 devstatus 4-33 diskonline 4-34 diskstatus 4-35 displayoperatormsg 4-35 doidlefonts 4-35 dojamrecovery 4-36 doprinterrors 4-36 doret 4-36 dostartpage 4-37 dosysstart 4-37 duplexer 4-37 duplexmode 4-38 enginesync 4-38 file 4-39 filenameforall 4-39 fileposition 4-39 firstside 4-40 fontnonzerowinding 4-40 hardwareiomode 4-40 idlefonts 4-40 ignoresize 4-41 initializedisk 4-41 jobname 4-41 jobsource 4-42 jobtimeout 4-43 manualfeed 4-43 manualfeedtimeout 4-44 newsheet 4-44
common 3-48 printer unique 3-49 physical page
PCL emulation 2-3 PostScript emulation 4-3 physical page border 2-7 physical specifications 7-4 ports, communication 8-2
Windows 2000 8-4 Windows 95/98/Me 8-2 Windows NT 4.0 8-3 Windows XP 8-5 PostScript emulation
accessing files 6-9 command format 4-14 device names 6-9 device parameters 4-85 device search order 6-12 envelope size support 4-23 filenames 6-9 fonts
Lexmark C510(n) 4-9 Lexmark E323 4-12 Lexmark X422 4-7 interpreter parameters 4-76 page device parameters 4-62 page formatting 4-3 paper size commands
currentuniversalsize 4-17 ignoresize 4-17 setignoresize 4-17 setuniversalsize 4-18 paper sizes supported 4-15 paper tray commands
manualfeed 4-21 papertray 4-21 setpapertray 4-22 paper tray support 4-18 password protecting

pagecount 4-44 pagesprinted 4-45 papertray 4-45 printername 4-45 product 4-45 PS2fonts 4-46 PS3fonts 4-46 quiet 4-46 ramsize 4-47 realformat 4-47 renamefile 4-47 resolution 4-48 revision 4-48 sccbatch 4-49 sccinteractive 4-50 setcoverpage 4-50 setdefaulttimeouts 4-50 setdoidlefonts 4-51 setdojamrecovery 4-51 setdoprinterrors 4-51 setdoret 4-52 setdostartpage 4-52 setdosysstart 4-53 setduplexmode 4-53 setenginesync 4-54 setethernetaddress 4-54 setfilenameextend 4-54 setfileposition 4-55 sethardwareiomode 4-55 setidlefonts 4-55 setignoresize 4-55 setjobtimeout 4-56 setmanualduplexmode 4-56 setpapertray 4-56 setprintername 4-57 setquiet 4-57 setresolution 4-58 setsccbatch 4-58 setsccinteractive 4-59 setsoftwareiomode 4-59 settumble 4-59 setuserdiskpercent 4-60 softwareiomode 4-60 tumble 4-60 userdiskpercent 4-61 waittimeout 4-61 system parameters 4-79 unsolicited messages 4-108
user parameters 4-76 using the operator panel 4-1 power requirements 7-2 printable areas 2-3, 2-7, 4-3 Printer Job Language (PJL)
30 Print Unit Missing 3-67 30 Coating Roll Missing 3-67 31 Defective Cartridge XXXX 3-67 31 Defective Print Cartridge 3-67 31 Missing Cartridge XXXX 3-68 31 Missing Printhead 3-68 31 PerfectFinish Missing 3-70 32 Unsupported Cartridge 3-67 32 Unsupported Cartridge 3-67 32 Unsupported Print Cartridge 3-67 32 Unsupported Printhead 3-68 33 Tray x Config Error 3-69 40 Tray x Size Sense Error 3-68 41 Open Bin 1 Exit Tray 3-68 58 Input Config Error 3-69 58 Too Many Bins Attached 3-69 58 Too Many Disks Installed 3-69 58 Too Many Trays Attached 3-69 59 Incompatible Bin x 3-71 84 All Photo Devs Exhausted 3-70 84 Black Photo Dev Exhausted 3-70 84 Black Photo Dev Life Warning 3-70 84 Color Photo Dev Life Warning 3-70 87 PerfectFinish Empty 3-70 88 Black Print Cartridge Low 3-70 88 Black Toner Empty 3-70 88 Black Toner Low 3-70 88 Cartridge Low 3-71 88 Color Print Cartridge Low 3-70 88 Cyan Toner Empty 3-70 88 Cyan Toner Low 3-70 88 Magenta Toner Empty 3-70 88 Magenta Toner Low 3-70 88 Photo Print Cartridge Low 3-70 88 Toner Low 3-70 88 Yellow Toner Empty 3-70 88 Yellow Toner Low 3-70 89 Cartridge Empty 3-71 2xx Paper Jam 3-69 Cartridge Life Expired XXXX 3-67 Cartridge Life Warning XXXX 3-68 Change Cartridge Invalid Refill 3-67
attendance messages 3-67

Check Duplex Connection 3-71 Check Finisher Installation 3-69 Check Mailbox Installation 3-69 Check Tray Connection 3-69 Close Cover 3-68 Close Cover 3-68 Close Cover A 3-67 Close Deflector G 3-68 Close Door 3-67 Close Door 3-68 Close Duplex Door 3-72 Close Finisher Door 3-68 Close Finisher Side Door 3-68 Close Finisher Top Cover 3-68 Close Front Door 3-68 Close Side Door 3-68 Close Top Covers 3-67 Close Tray x Top Cover 3-68 Cover Open 3-67 Incompatible Duplex 3-71 Incompatible Envelope Feeder 3-71 Incompatible Tray x 3-71 Insert Cartridge 3-67 Insert Duplex Option 3-72 Insert Hole Punch Box 3-67 Insert PC Cartridge 3-67 Insert Print Cartridge 3-69 Install Bin x or Cancel Job 3-69 Install Duplex or Cancel Job 3-72 Install Env Feed or Cancel Job 3-69 Install Tray x or Cancel Job 3-69 Load Staples 3-71, 3-72 Open Cover 3-68 Open Rear Door 3-68 OPMSG message 3-71 paper handling
Remove Paper All Output Bins 3-73 Remove Paper Output Bin 3-
73 Remove Paper Standard Bin 3-73 paper jams
200 Paper Jam 3-76 201 Paper Jam 3-76 202 Paper Jam 3-76 203 Paper Jam 3-76 204 Paper Jam 3-76 205 Paper Jam 3-76 206 Paper Jam 3-76 207 Paper Jam 3-76 208 Paper Jam 3-76 220 Paper Jam 3-76 221 Paper Jam 3-76 222 Paper Jam 3-76 230 Paper Jam 3-76 231 Paper Jam 3-76 232 Paper Jam 3-77 241 Paper Jam 3-77 242 Paper Jam 3-77 243 Paper Jam 3-77 244 Paper Jam 3-77 245 Paper Jam 3-77 246 Paper Jam 3-77 247 Paper Jam 3-77 248 Paper Jam 3-77 249 Paper Jam 3-77 24y Paper Jam 3-77 250 Paper Jam 3-77 251 Paper Jam 3-77 252 Paper Jam 3-77 253 Paper Jam 3-78 254 Paper Jam 3-78 255 Paper Jam 3-78 256 Paper Jam 3-78 257 Paper Jam 3-78 258 Paper Jam 3-78 259 Paper Jam 3-78 260 Paper Jam 3-78 261 Paper Jam 3-78 271 Paper Jam 3-78 272 Paper Jam 3-78 273 Paper Jam 3-78 27z Paper Jam 3-78 280 Paper Jam 3-78 281 Paper Jam 3-79
34 Incorrect Media 3-73 34 Wrong Paper Size in Tray x 3-73 34 Wrong Paper Size Manual Feed 3- 73 Change 3-73 Check Paper Guide 3-73 Insert Duplex Pages & Press Go. 3-73 Insert Tray 3-73 Load 3-73 Load Manual 3-73 Remove Paper 3-73

282 Paper Jam 3-79 283 Paper Jam 3-79 284 Paper Jam 3-79 285 Paper Jam 3-79 286 Paper Jam 3-79 287 Paper Jam 3-79 288 Paper Jam 3-79 289 Paper Jam 3-79 290 Paper Jam 3-79 291 Paper Jam 3-79 292 Paper Jam 3-79 293 Paper Jam 3-79 294 Paper Jam 3-80 295 Paper Jam 3-80 Priming Failed. Retry? 3-71 Reattach Bins 3-69 Reattach Envelope Feeder 3-69 Reattach MP Feeder 3-69 Reattach Output Bin 3-69 Replace Fuser 3-71 Replace Oil Coating Roll 3-71 Replace PC Kit 3-71 Replace PC Kit To Continue 3-71 Replace Toner Cartridge 3-71 Replace Toner Cartridge To Continue 3-71 Replace Transfer Kit 3-71 STMSG message 3-71 auto-continuable messages 3-63
54 Std Network Software Error 3-63 54 Std Par ENA Connection Lost 3-64 54 Std Ser Fax Connection Lost 3-63 55 Insufficient Fax Buffer 3-64 56 Parallel Port Disabled 3-64 56 Parallel Port x Disabled 3-65 56 Serial Port 1 Disabled 3-64 56 Serial Port x Disabled 3-65 56 Standard Parallel Port Disabled 3-64 56 Standard Serial Disabled 3-63 56 Standard USB Port Disabled 3-64 56 Std Parallel Port Disabled 3-64 56 USB Port x Disabled 3-65 57 Configuration Change 3-63 58 Too Many Flash Options 3-66 61 Defective Disk 3-64, 3-66 61 Unformatted Disk 3-64 62 Disk Full 3-64, 3-66 63 Unformatted Disk 3-66 64 Unsupported Disk Format 3-66 80 Belt Exhausted 3-66 80 Belt Life Warning 3-66 80 Fuser Exhausted 3-66 80 Fuser Life Warning 3-66 80 Fuser Maintenance 3-66 80 Fuser/Belt Exhausted 3-66 80 Fuser/Belt Life Warning 3-66 80 Scheduled Maintenance 3-65, 3-66 81 Scheduled Maintenance 3-66 83 ITU Maintenance 3-66 Disk Corrupted. Reformat? 3-66 Empty Box M 3-65 Held Jobs May Not Be Restored 3-63 Insert Box M 3-65 Insert Staple Cartridge 3-65 Insert Stapler 3-65 Operation Failed Faxes on Disk 3-65 Operation Failed Jobs on Disk 3-65 Priming Failed, Retry. Go/Stop? 3-65 Print Jobs on Disk. Go/Stop? 3-64 Print Jobs on Disk? 3-64 Restore Held Jobs. Go/Stop? 3-64 command categories
34 Short Paper 3-64 35 Res Save Off Deficient Memory 3-64, 3- 65 36 Resolution Reduced 3-64 37 Insufficient Collation Area 3-63, 3-65 37 Insufficient Defrag Memory 3-63 37 Insufficient Memory 3-63 38 Memory Full 3-63 39 Complex Page 3-63 50 PPDS Font Error 3-63 51 Defective Flash 3-64, 3-66 52 Flash Full 3-64, 3-65 53 Unformatted Flash 3-64, 3-66 54 Network x Software Error 3-65 54 Par x ENA Connection Lost 3-65 54 Parallel Error 3-63 54 Ser x Fax Connection Lost 3-65 54 Serial Option 1 Error 3-63 54 Serial Option x Error 3-65 54 Standard Serial Error 3-63
device attendance 3-80 file and device protection 3-93 file commands for flash and disk 3-86 job separation commands 3-4 kernel commands 3-2

miscellaneous 3-82 status readback 3-53, 3-54 command syntax
88 Cyan Toner Low 3-61 88 Magenta Toner Low 3-61 88 Photo Print Cartridge Low 3-61 88 Toner Low 3-61, 3-62 88 Yellow Toner Low 3-61 Bin Full 3-62 Busy 3-62 Cancelling Job 3-62 Not Ready 3-61 Power Saver with 88 Ink Low 3-62 Powersaver 3-62 RDYMSG 3-61 Ready 3-61 Ready with 88 Ink Low 3-61 Replace Fuser 3-61, 3-62 Replace PC Kit 3-61, 3-62 Replace Toner 3-61, 3-62 Replace Transfer 3-62 Res Reduced 3-62 Resetting the Printer 3-61 Tray Empty 3-62 Tray Missing 3-62 Waiting 3-62 status messages and codes 3-61 variable categories 3-7
command codes 3-1 optional parameters 3-2 commands
COMMENT 3-3 DEFAULT 3-8, 3-94 DINQUIRE 3-54 ECHO 3-55 ENTER LANGUAGE 3-3 EOJ 3-6 INFO 3-56 INITIALIZE 3-11 INQUIRE 3-58 JOB 3-4 LBEEP 3-82 LBYPASSPASSWORD 3-97 LCLOSEFILE 3-89 LDECLARE 3-95, 3-97 LDELETEFILE 3-92 LDELETEPASSWORD 3-96 LDOWNLOADTARGET 3-86 LESCAPECHAR 3-83 LFAX PHONENUMBER 3-85 LFORMAT 3-92 LOPENFILE 3-89 LPORTROTATE 3-82 LPRINTDIRECTORY 3-83, 6-4 LPRINTMENUS 3-83 LPRINTPCLFONTS 3-83 LPRINTPSFONTS 3-83 LPRINTTESTPAGE 3-83 LREADFILE 3-90 LRENAMEFILE 3-92 LRUNFILE 3-91 LWRITEFILE 3-91 OPMSG 3-81 RDYMSG 3-80 RESET 3-11 SET 3-9 STMSG 3-81 USTATUS 3-59 USTATUSOFF 3-60 information messages
all printer languages 3-12 PCL emulation 3-48 PostScript emulation 3-51 printer unique
all printer languages 3-19 LRESOURCE 3-52 PCL emulation 3-49 PostScript emulation 3-52 variables
AUTOCONT 3-12 BINDING 3-12 BITSPERPIXEL 3-12 CLEARABLEWARNINGS 3-12 COPIES 3-12 CPLOCK 3-13 DENSITY 3-13 DUPLEX 3-13 ECONOMODE 3-13 FONTNUMBER 3-48 FONTSOURCE 3-48 FORMATTERNUMBER 3-13 FORMLINES 3-13
88 Black Print Cartridge Low 3-61 88 Black Toner Low 3-61 88 Color Print Cartridge Low 3-61
common variables

LPSFONTPRIORITY 3-52 LPUNCH 3-43 LREAROUTBINNAME 3-43 LREPEATLIMIT 3-43 LRESET 3-43 LRESOURCESAVE 3-43, B-9 LRIGHTMARGINOFFSET 3-43 LRWLOCK 3-53 LSCREENING 3-43 LSEPARATORSHEETS 3-43 LSEPARATORSOURCE 3-43 LSTANDARDOUTBINNAME 3-44 LSTAPLE 3-44 LSTAPLESEMPTYALARM 3-44 LSTAPLETESTBIN 3-44 LSTAPLETESTSOURCE 3-44 LSTROKEWIDTH 3-44 LSUBSTITUTESIZE 3-44 LTHINCOAT 3-44 LTOPBINROTATE 3-44 LTOPMARGINOFFSET 3-44 LTRANSPARENCYLENGTH 3-44 LTRANSPARENCYOUTBIN 3-45 LTRANSPARENCYTEXTURE 3-45 LTRANSPARENCYWEIGHT 3-45 LTRAY1AUTOSIZE 3-46 LTRAY1PAPERTYPE 3-46 LTRAY1RENUMBER 3-47 LTRAY1SENSEDTYPEPAPER 3-45 LTRAY1SENSEDTYPETRANSPARENCY
LTYPE1FONTS 3-47 LUSDEFAULTS 3-47 LWLOCK 3-53 MANUALFEED 3-15 MEDIATYPE 3-15 MPTRAY 3-15 ORIENTATION 3-15 OUTBIN 3-16 PAGEPROTECT 3-16 PAPER 3-16 PARALLEL 3-17 PASSWORD 3-17 PERSONALITY 3-17 PITCH 3-48 POWERSAVE 3-17 POWERSAVETIME 3-18 PRTPSERRS 3-51 PTSIZE 3-48 QTY 3-18 REPRINT 3-18 RESOLUTION 3-18 RESOURCESAVE 3-18 RET 3-18 SYMSET 3-48 TIMEOUT 3-18 USERNAME 3-19 WIDEA4 3-19 printer languages, selecting
MarkVision Professional 2-1 methods 5-1 operator panel 2-1, 4-1 PCL emulation 2-1 Printer Job Language (PJL) 3-3 setting for different interfaces 5-2 SmartSwitch 5-1 software program 2-2 switching 5-1 printer specifications
3-45 LTRAY3AUTOSIZE 3-46 LTRAY3PAPERTYPE 3-47 LTRAY3SENSEDTYPEPAPER 3-46 LTRAY3SENSEDTYPETRANSPARENCY
airflow requirement 7-1 altitude 7-5 atmospheric pressure 7-5 clearance requirements 7-4 dimensions 7-4 electrical 7-2 environmental conditions 7-5 flash memory and disk retrieval speeds 6-13 interfaces 8-1 noise emission levels 7-1
3-46 LTRAY5AUTOSIZE 3-46 LTRAY5PAPERTYPE 3-47

power requirements 7-2 size 7-4 time to power on to Ready state 7-6 time to print first page 7-6 weight 7-4 protocol
cable pin assignments 8-37 connecting 8-36 serial communication parameters 8-38 using 8-36 XON/XOFF protocol timing 8-40
DTR/DSR 8-32 fastbytes data transfer sequence 8-16 Robust XON 8-31 RS-232C 8-33 standard data transfer sequence 8-15 XON/XOFF 8-34
setting for different interfaces 5-2 SmartSwitch 5-1 serial interface
link buffer 8-43 network support 8-42 RS-232C
raster compression mode 2-88
cable pin assignments 8-26 communication parameters 8-29 DTR and DTR/DSR protocol timing 8-33 port compatibility 8-36 protocol 8-32 serial configuration recommendations 8-35 RS-422 cable pin assignments 8-37 using RS-232C 8-26 using RS-422 8-36 when to use 8-25 service errors 3-80 signal descriptions 8-19 size, printer 7-4 SmartSwitch 5-1
adaptive compression 2-92 delta row 2-91 group 3 and 4 2-93 Lexmark adaptive 2-94 run-length encoded data 2-90 Tagged Image File Format (TIFF) 2-90 uncoded data 2-89 raster image graphics 2-88 receivers
Lexmark C510 8-20 BUSY driver
Lexmark C510 8-23, 8-24 DATA 1-8 Signal
setting for different interfaces 5-2 switching printer languages 5-1 sniffing 5-3 specialty PCL emulation fonts
Lexmark C510 8-21 INIT*
Lexmark C510 8-23, 8-24 SLCTIN*
forward/backward compatibility modes 2-31, 2-
Lexmark C510 8-24, 8-25 STROBE
42 specialty PCL fonts 2-31, 2-42 specifications
Lexmark C510 8-19, 8-20, 8-21, 8-22, 8-
23, 8-24, 8-25 required clearance 7-4 Resource Data Collection 6-2, 6-3 Robust XON protocol 8-31 RS-232C
See printer specifications standard PCL emulation fonts 2-10, 2-20, 2-30, 2-
38 forward/backward compatibility modes 2-10, 2-
20, 2-30, 2-38 standard protocol 8-15 status messages
cable pin assignments 8-26 connecting 8-26 port compatibility 8-36 protocol timing 8-33 XON/XOFF protocol timing 8-34 RS-422
attendance conditions 3-67 auto-continuable conditions 3-63 information messages 3-61 operator intervention - paper handling 3-72
selecting printer languages

operator intervention - paper jams 3-75 PostScript emulation 4-107 switching printer languages
page size 2-64 paper source 2-64 PostScript emulation
MarkVision Professional 2-1 methods 5-1 operator panel 2-1, 4-1 PCL emulation 2-1 PostScript emulation 4-1 Printer Job Language (PJL) 3-3 setting for different interfaces 5-2 SmartSwitch 5-1 software program 2-2, 4-2 Symbol Set Tables, locating ID values 2-60 symbol sets
automatic size sensing search order 4-18 operators 4-20 Printer Job Language (PJL)
paper size 3-14 paper source 3-39 status message codes 3-74 Type 1 fonts
description 2-13, 2-23, 2-40 forward/backward compatibility modes 2-13, 2-
flash memory or disk 6-3 selecting
Universal Exit Language 3-2 unsolicited messages 4-108
Lexmark C510(n) 2-25 Lexmark E321 2-32 Lexmark E323 2-43 Lexmark T630 2-43 Lexmark T632 2-43 Lexmark T634 2-43 Lexmark X422 2-15 setting password protection 3-93 storing on flash memory or disk 6-3 support
common for all printer languages 3-12 common for PCL emulation 3-48 common for PostScript emulation 3-51 environment 3-7 printer unique for all printer languages 3-19 printer unique for PCL emulation 3-49
ISO fonts 2-18, 2-28, 2-36, 2-58 non-text fonts 2-17, 2-27 text fonts 2-15, 2-25 syntax, commands
PCL emulation 2-59 PostScript emulation 4-14 Printer Job Language 3-1
weight, printer 7-4 whole page setting 2-8
test page, printing from PJL
flash memory and disk directory 3-83, 6-4 menu settings page 3-83 PCL emulation font list 3-83 PostScript emulation font list 3-83 printer test page 3-83 time
to power on to Ready state 7-6 to print the first page 7-6 trays
Pages referenced in this manual — manufacturer, support and downloads.
What the fault codes shown on the display mean and how to clear them.
| Code | Meaning | Fix | |
|---|---|---|---|
| 1 | File system access has not been initialized | p.236 | |
| 2 | Could not allocate file descriptor | p.236 | |
| 3 | Some invalid argument was passed | p.236 | |
| 4 | No such device | p.236 | |
| 5 | Invalid access to file requested | p.236 | |
| 6 | Argument too large (filename, buffer) | p.236 | |
| 7 | Invalid file descriptor or filename | p.236 | |
| 8 | Catch all error or device error | p.236 | |
| 9 | Unable to allocate memory for buffer, data structure | p.236 | |
| 10 | Device busy | p.236 | |
| 11 | Device not currently mounted | p.236 | |
| 12 | Attempt to perform illegal IO operation | p.236 | |
| 13 | No space to update or create file | p.236 | |
| 14 | Major change in file system for findnext() to function properly | p.236 | |
| 15 | Corrupted file system on device | p.236 | |
| 16 | Device already mounted | p.236 | |
| 17 | Could not initialize file system | p.236 | |
| 18 | Device not mounted | p.236 | |
| 19 | No file entry located | p.236 | |
| 20 | Bad file system on device | p.236 | |
| 21 | Password required | p.236 | |
| 22 | Aborted by callback | p.236 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.