




For use with:
Windows 95/NT operating systems
Novell NetWare networks

The contents of this manual may be revised without prior notice and without obligation to incorporate changes and improvements into units already shipped.
Every effort has been made to ensure that the information included here is complete and accurate at the time of publication, but we cannot be held responsible for errors and omissions.
Copyright Lexmark International, Inc. 1994, 1996
Printed in Spain. All rights reserved. No part of this manual may be reproduced or translated, stored in a database or retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Lexmark International, Inc.
Lexmark, MarkVision and Mark Net are registered trademarks of Lexmark International, Inc.
The following companies own the other trademarks used in this manual:
Novell, Inc.: NetWare
C145-E207-02EN, June 1997 · Trademark Acknowledgement


In this book, the term utilities refers to the files on the CD-ROM or diskettes that you received with the printer. The term adapter refers to this Network Adapter. The term adapter list refers to the list of adapters on your network that the utility displays.
For example, suppose you want to print the adapter list to a printer. You would choose the File menu, the Print command under File, and the To Printer option. That path is shown as File/Print/To Printer.
The Network Printer Utility will be shipped on CD-ROM or diskettes with the printers.

Preface

Overview of the Utilities, the Network Adapter and MarkVision 1 Overview of the Utilities, the Network Adapter and MarkVision
Introduction Thank you for buying this multi-protocol Network Adapter. As with most new purchases, you probably have a few questions. We will answer some of them in this introduction for you.
::
You’ve received, in this package, the latest level of the utilities that were available when the printer was built. There is firmware that resides on the adapter itself. This firmware handles communications between the printer, the utility, the adapter, and the network. The firmware is, therefore, the backbone of this product. The firmware resides on the adapter’s flash memory, a type of Read-Only Memory that can be erased electronically and reprogrammed. (To check an effective firmware level, contact your point of purchase.) To find out which firmware revision level uses your adapter, print a setup page. For help, see “Step 2: print a setup page” on page 2-3.

Yes. See the Windows 95 chapter in this manual for more information.
Yes. The Network Adapter is shipped with all protocols active. Using the Network Printer Utility for Windows 3.1 or MarkVision for Windows 95, you can turn off protocols that you don’t need. Each protocol consumes some resource on the adapter and network. If you turn a protocol off, that resource is released. Therefore, to increase throughput on the adapter, we recommend that you turn unused protocols off. For example, if you are not using the TCP/IP protocol you may choose to turn it off. This reduces network traffic.
Introduction

Overview of the Utilities, the Network Adapter
Yes. The Network Adapter accepts print jobs from NetWare and TCP/IP, one job at a time. The adapter accepts print jobs in the order they are received: first- come, first-served.
Each diskette or CD-ROM includes a README file. This file contains late- breaking information and offers tips we may have discovered after printing this guide. Please read this file and use it to help you.
You can get help from several sources. • Use pull-down menus. Each item in the utility’s pull-down menus has help enclosed with it. To see that help:
a Point and click on the menu that you want help with.
b Press F1.
Introduction · and MarkVision

Introduction

Introduction Thank you for buying this multi-protocol adapter. This chapter explains how to set up and use your printer on a Transmission Control Protocol/Internet Protocol (TCP/IP) network using this Network Adapter.
This chapter is designed for technical people such as TCP/IP programmers and experienced network administrators. It assumes that you have a good working knowledge of your TCP/IP hardware and software.

This utility guide uses standard TCP/IP protocols. Information about these standard protocols is available in RFCs (Request For Comments). These RFCs contain TCP/IP information that is not unique to the Network Adapter. To obtain an RFC, use FTP services on the Internet as an anonymous user to:
nic.ddn.mil
Look for the RFC in the /rfc directory. For more information about TCP/IP, we recommend a book by Douglas Comer entitled Internetworking with TCP/IP, Volume I: Principles, Protocols, and Architecture.
Setup Before you can use the adapter, you need to set it up. Setup involves a few simple steps:
1 Checking the physical connections.
2 Printing a setup page to use while you set up the adapter.
3 Setting the adapter’s IP address, netmask, and gateway.
4 Verifying the setup.
5 Setting a community name.
The rest of this Setup section tells you how to do these steps.
Setup

Next you need to print a setup page. Keep the setup page. You’ll use information from it later.
Printing a setup page
1 Press the Test button on the adapter until the Test light comes on.
The Data light comes on, and the adapter sends a page to the printer, similar to the one on page 2-4.
Setup · TCP/IP networks

The Network Adapter setup page looks similar to the example below.
Type: Ethernet EOJ Timeout: 90 UAA: 00200008A803 0004001015C0 LAA: 000000000000 000000000000 Part Number, EC: 1381603, MN_XL_E Firmware Revision: 4.124.1

Setup · TCP/IP networks

Setting the information using a bootstrap protocol
You may set the IP address, netmask, and gateway using a TCP/IP bootstrap protocol (BOOTP), if you have a BOOTP server running on your network. Make sure the BOOTP server is running on the same LAN segment as the adapter. (Some routers will pass the packets, but many will not. If the BOOTP server is on a different LAN segment, check your router’s documentation to be sure packets will cross.) To set the IP address, netmask, and gateway using a TCP/IP bootstrap protocol:
1 Find the hardware address for the adapter. To find the hardware address, look at the setup page for the adapter. The address is labelled UAA an LAA on the setup page. • If you are using an Ethernet adapter, be sure to use the address in the right column. This is the canonical form of the address, circled on the sample setup page on page 2-4.
Choose the Locally Administered Address (LAA), unless it is 000000000000. If the LAA is 000000000000, choose the Universally Administered Address (UAA).
2 Set up the BOOTP server. To do so, edit the BOOTP file on the host computer that is running the BOOTP server. The file is usually located in /etc/bootptab.
The file contains information such as the hostname and the IP address. For example, a bootptab record might look similar to this:
jdlprt:\ ht=ether:\ ha=08005A09E610:\ ip=9.51.8.212:\ sm=255.255.255.128:\ gw=9.51.8.132
where the following means:
jdlprt hostname. ht=ether hardware type. ha=08005A09E610 hardware address. ip=9.51.8.212 IP address. sm=255.255.255.128 netmask. gw=9.51.8.132 gateway.
If you need help editing the BOOTP file, try the man page that came with your UNIX software. Most popular UNIX workstations contain man pages that help you with tasks like this. You might try man bootp or man bootptab. If that doesn’t work, consult your system’s documentation.
Setup

3 Make sure that BOOTP is enabled.
You can do this from the printer control panel.
To enable BOOTP from the printer control panel, follow these steps:
a Turn the printer power On (|).
b Use the printer control panel to find the menu item SETUP NETWORK
MENU. Consult your printer documentation to learn the menu path for your specific printer, or scroll through the control panel menus until you find it.
c Select SETUP NETWORK MENU.
d Select Enable BOOTP.
e Select Yes.
If you are instructed to do so, turn the printer off.
f When you are finished, select Ready.
4 Set up the printer’s hostname (network name) in the computer. To do so, simply define the printer’s IP name and address in the /etc/hosts file or on the name server.
This IP address and hostname must match those you set earlier in the BOOTP file. You may want to use a hostname that is meaningful in your environment (for example, a name that identifies the printer’s location).
Setup · TCP/IP networks

Setting the information via the printer control panel
If you already know the printer’s IP address, netmask, and gateway, you may want to set them at the printer’s control panel. This process sets the address, netmask, and gateway at this printer only and does not update any BOOTP records you have in your server.
1 Using the printer’s control panel, set the IP address, netmask, and gate- way. If you need help, follow these steps:
a Turn the printer power On (|).
b Use the printer control panel to find the menu item SETUP NETWORK
MENU. Consult your printer documentation to learn the menu path for your specific printer, or scroll through the control panel menus until you find it.
c Select SETUP NETWORK MENU.
d Select Set IP ADDRESS, and press ENTER. A screen similar to the
following appears:
e Use the MENU button to place the cursor beneath the part of the IP
address that you want to set. Then use the plus (+) and minus (-) keys to set the address.
f Press ENTER.
g Select Set IP NETMASK, and press ENTER.
h Set the IP netmask just as you set the IP address.
i Press ENTER.
j Select Set IP GATEWAY, and press ENTER.
k Set the IP gateway just as you set the IP address.
l Press ENTER.
m Press READY. Your settings take effect when you return to the Ready
screen.
If an error message appears on the printer’s control panel, go to “Using the printer control panel” on page A-1.
Setup

2 Using the printer’s operator panel, make sure that BOOTP is disabled. We recommend that you leave BOOTP disabled if you are not using it to set IP addresses. If you need help, follow these steps:
a Turn the printer power On (|).
b Use the printer control panel to select the menu item SETUP
NETWORK MENU. Consult your printer documentation to learn the menu path for your specific printer, or scroll through the control panel menus until you find it.
c Select SETUP NETWORK MENU.
d Select Enable BOOTP.
e Select No.
If you are instructed to do so, turn the printer off.
f When you are finished, select Ready.
3 Set up the printer’s hostname (network name) in the computer. To do so, simply define the printer’s IP name and address in the /etc/hosts file or on the name server.
This address must match the IP address you set earlier on the printer’s control panel. You may want to use a hostname that is meaningful in your environment (for example, a name that identifies the printer’s location).
Setup · TCP/IP networks

Setting the information using a RARP server and telnet
You may set the IP address using a RARP (Remote Address Resolution Protocol). You must make sure that you are working on the same physical network as the adapter. Then you can set the netmask and gateway with telnet. To set the IP address, netmask, and gateway using a RARP server and telnet:
2 Look at the setup page. Make sure BOOTP and RARP are enabled.
3 Set up the RARP server, following the instructions provided by your host operating system.
4 Turn the printer off then on to reset the adapter.
The adapter sends a RARP request, and the server responds.
5 Use telnet to set the netmask and gateway by typing:
telnet ip.address -p 9000
where ip.address is the IP address you’re using, such as 9.51.8.231.
6 Follow the instructions on the screen to set the netmask and gateway.
If you wish to change the address, netmask, gateway, or community name in the future, you may find this telnet function helpful.
Setup

Setting the information by editing an ARP table and using telnet
You may set the IP address by editing an Address Resolution Protocol (ARP) table. You must make sure that the computer where the ARP table is edited is on the same physical network as the adapter. The adapter cannot send this information across a router, until the adapter is configured. Then you can use telnet to set the netmask and gateway. To set the IP address, netmask, and gateway using an ARP file and telnet:
1 Look at the printer setup page. Find the hardware address. It is labelled UAA and LAA. • If you are using an Ethernet adapter, be sure to use the address in the right column. This is the canonical form of the address, circled on the sample setup page printed on page 2-4.
Choose the Locally Administered Address (LAA), unless it is 000000000000. If the LAA is 000000000000, choose the Universally Administered Address (UAA).
2 Edit the ARP table to add an IP address. Make sure you use the dotted form of the IP address, such as 9.51.8.231. Use the commands appropriate to the host operating system. On many computers you would type something similar to the following:
arp -s 9.51.8.231 08:00:5A:09:E6:10
If you need help and are using a UNIX system, try the man page.
3 PING the adapter. This sets the new address on the adapter. For example, you might type something similar to:
ping 9.51.8.231
4 Use telnet to set the netmask and gateway. For example, you might type something similar to:
telnet 9.51.8.231 -p 9000
5 Follow the instructions on the screen to set the netmask and gateway.
Setup · TCP/IP networks

You can check to make sure the printer is set up correctly. Just follow these steps.
1 Make sure your computer is on the same physical network as the adap- ter.
2 Print a test page to verify your settings. If you need help, go to “Step 2: print a setup page” on page 2-3.
3 Issue a PING command from your computer, such as:
where hostname is the hostname that you set in the /etc/hosts file or on the name server.
file. • If you set the address, netmask, and gateway from the printer control panel, make sure that:
– The IP address is set correctly on the printer’s control panel. If you
need help, see “Setting the information via the printer control panel” on page 2-8. • If you set the IP address, netmask, and gateway using a RARP server or ARP command and telnet, double-check all your steps. If one of these parameters is wrong, your connection will be lost.
Setup · ping hostname

After you have set the TCP/IP information, you can change it using any of the ways you set the information, or by doing one of the following. This is also the way to set a community name. • Telnet to port 9000 to change the information.
telnet ip.address -p 9000
where ip.address is the IP address you’re using, such as 9.51.8.231.
2 Follow the instructions on the screen. • FTP a file to the param directory. The param directory is a special directory where you can change special TCP/IP-related parameters.
The format of this file should be:
Setup · TCP/IP networks

To ftp to the directory:
ftp ip.address
where ip.address is the IP address you’re using, such as 9.51.8.231.
3 Type:
where config -file is the name of the file containing the configuration you want to use.
4 Quit.
What to do next
You have set up your adapter and are ready to use it. Continue with “Using the protocols“.
This section explains how to use standard TCP/IP protocols to send jobs to the printer and to check the status of print jobs. It explains how this Network Adapter implements standard TCP/IP protocols such as:
Note: The firmware in the Network Adapter includes support for other adapters. The Network Adapter contains only one port (PORT 1) which supports this printer. The multi-purpose firmware in the Network Adapter may make references to port 2 (or IBM 4029 printers), but these statements apply to other types of hardware. Furthermore, any statuses refering to MarkNet XLe should be treated as equivalent statuses of the Network Adapter.
Using the protocols · cd param · put config-file

You can send jobs to the printer in one of four ways:
Using the protocols · TCP/IP networks

You may already use Line Printer Remote and Line Printer Daemon (LPR/ LPD) programs to send print jobs. The LPR program usually runs on the host computer, sending print jobs and control files to the LPD program running on the print server. This TCP/IP adapter includes a line printer daemon, which prints previously formatted data files, as received, and ignores the control file. You can use your LPR/LPD program to send jobs to the adapter’s line printer daemon.
Using the LPR command
printer_cr Sends print jobs to the port, and causes the adapter to add a carrier return (or line feed, if appropriate) at the end of each line of text.
printer Sends print jobs to the port.
- those relating to the banner page, - indentations in the print job, or - mail sent after the job do not work.
Note: A queue name may end with any character except “2“. If you used a “2“ at the end of a queue name, your print jobs will not be printed. Under Windows, you can avoid this error by doing one of the following. (1) Set “_cr“ at the end of the queue name in Windows NT, or (2) Select the Carriage Return and Linefeed insertion mode in “Set lpd options“ when you go into the Main Menu of the Adapter under the program Telnet. By doing one of the two above mentioned, the Adapter will add the Carriage Return and Linefeed codes automatically to your print job.
Using the protocols · Example Function

LPR time-outs and retry periods
Some LPR programs wait only a limited amount of time to send their print files. If you receive a timeout message from your host, the adapter was probably printing a long job. You should retry the print job. The adapter supports a finite number of active LPR connections at a time. If more than this number of connections are attempted, the extra attempts will not work. Many UNIX programs retry the print job after a specified amount of time. If you want to use several active LPR connections, we recommend that you set a short retry period so that print jobs will be sent until they are accepted. Some UNIX systems may default to a 15-minute retry period. We recommend that you use the lp-system command to set a shorter retry period for those computers. You can also telnet to port 9000, then follow the instructions on the screen.
LPSTAT and LPQ commands
Most line printer status (LPSTAT) commands work as usual with this adapter. We recommend that you use the finger command to get the status of the printer, rather than a line printer query (LPQ) command. Finger returns much more useful information to you than the LPQ command. If you need information about using finger to get the printer status, see “Using Finger” on page 2-22.
Using telnet to add carrier returns or line feeds to all LPD print jobs
You can use telnet to change the LPD protocol so that it automatically adds carrier returns or line feeds to all print jobs. You may find this helpful if you are printing text files without graphics.
1 Type the following at the command prompt:
telnet ip.address -p 9000
where ip.address is the IP address you’re using, such as 9.51.8.231.
2 From the menu that appears, select Set lpd options.
3 Follow the instructions on the screen.
Using the protocols · TCP/IP networks

You can use telnet with the adapter. This is an easy way to set the adapter’s parameters.
1 Set up the host to telnet in line mode, with local echo, and with cr/lf conversion. (Most hosts use this configuration as the default.)
2 If a password is set for the Network Adapter be sure you know it.
3 Type the following at the command prompt:
telnet ip.address -p 9000
where ip.address is the IP address you’re using, such as 9.51.8.231.
You can use TFTP to send a job to the printer just as you normally do. Remember that TFTP is slower than FTP. The Network Adapters only recognize the TFTP destination file name:
To use TFTP, type a command similar to this:
where <printfile> is the name of print job you’re sending and prt1 is the destination file.

The TFTP protocol used here includes a 30-second inactivity time-out. If data is not received from the host for 30 seconds, then the adapter closes the TFTP session and begins listening for a new session. The input/output port to the printer and the print job are also closed. This time-out prevents incomplete print jobs from hanging up in the printer and keeping other jobs from printing.
You can use FTP to send a job to the printer just as you normally do. FTP reliably sends files across the network. The implementation of FTP used here accepts any username and does not require a password. Network Adapters default to /prt1 as the destination. You may also use the cd command with a destination filename. For example, you might type
ftp>cd /prt1 ftp>put
where <prt1> is the name of the destination and <printfile> is the name of the print job you’re sending.
Sending a file to the param directory
You may also FTP a file to a special destination: the param directory. This is a special directory where you can set special TCP/IP-related parameters. The format of this file is:
You must put a space after the colon, and the headers must be capitalized. If you want a parameter to remain unchanged, you should type a period for that parameter (such as the NETMASK example above). The password can be up to eight characters long. The community name must be less than 30 characters long. You must send the file in ASCII mode (not binary).
Using the protocols · TCP/IP networks

There are two time-out periods that may occur in FTP: one during the control connection and one on the data connection. The time-out during the control connection is 60 seconds. If the control connection is started and no other command is issued for 60 seconds, then the control session is closed. The adapter sends a 421 reply code (service not available, closing control connection). The time-out default on the data connection is 90 seconds. If data is not received from the host for this data time-out period, then the adapter closes the FTP data session and begins listening for a new session. The input/output port to the printer and the print job are also closed. This time-out prevents incomplete print jobs from hanging up in the printer and keeping other jobs from printing.
Writing an FTP shell script
If you have written FTP shell scripts to send print jobs to the printer, you can revise those scripts to be used with this adapter. You may send print jobs to /prt1. The adapter will respond to the various commands with standard FTP reply codes. A sample shell script, on page 2-21, shows you what can be done. We do not guarantee that this script will be usable on your computer; it is simply given as an example for you. This script does as ASCII FTP of files specified on the command line, to the host identified in the variables. This shell takes data from stdin or from the print file you specify on the command line. You can specify several files on the command line. The -b option causes the transfer to occur in binary.
Using the protocols · Time-out periods

sss #1 /bin/sh module = $0
HOST=”silver” PRT=”/prt1” # overriding device default with prt1, # change this to reflect the desired # printer, or leave blank for default USER=”printer”
if [ ”`echo $1 | fgrep ’7’`” |= ”” ] # give help if there is a 7 in parm 1 then echo $USAGE exit 1 fi
set -- `getopt b $*` # check for ’b’ as a command if [ $? |= 0 ] then echo $USAGE exit 1 fi
XFER=”ascii” # default transfer type is ASCII
for i in $* do case $i in -b) XFER=”binary”,shift,, # changing transfer type to binary --) shift,break,, case done
if [ -z “$FileList” ] # no files specified?? then echo reading standard input 1 >&2 cat /tmp/p$$ # put std input to a file PutCmds=”put /tmp/p$$ SPRT ” # this double quote ”MUST” be on this line else
for i in $FileList # generate list of puts do FileName=$1 if [ -f $FileName ] # make sure the file exists then PutCmds=”${PutCmds}put $FileName $PRT ” # this double quote ”MUST” be on this line else echo ”$module: file $FileName does not exist - cannot print” fi done
ftp -n $HOST
rm -f /tmp/p$$ >/dev/null 2>/dev/null # remove the file if it exists

You can check the status of the network printer by using the TCP finger command.
Finger is a TCP protocol that normally displays user information on a local or a reachable host. This adapter uses finger to tell you the status of the printer and the current print job. For example, you may use:
where: info is optional. When you use it, the adapter returns extended information. name is the IP address or the name stored on the name server or in the /etc/hosts file. Please note that some UNIX environments require you to use the adapter’s name instead of its IP address. By default, finger returns the status of all the ports.
Using the protocols · Using Finger · finger info@name

The adapter sends an English response, as shown in the following example.
This example shows the response you get from the Network Adapter when you use the info option with finger. This particular example shows that a job is printing through the Parallel 1 port.
#finger [email protected]
[9.51.8.211]
Print Job Status for ser: NPA is supported, NPA mode is set to auto No Job Currently Active Printer Status: 0 OK
Print Job Status for prt1: NPA is supported, NPA mode is set to auto Printing Print Job Name: TEST.PRT User Name: Paul Queue/LPT Name: /PRT1 Server: 9.51.8.30 Network Operating System: FTP Printer Status: 0 OK
Adapter Information Adapter Type: Ethernet Firmware Revision: 139.44.1 Adapter Part Number: 1418622 Adapter EC: 543053 Adapter Address: 10005A101348 IP Address: 9.51.8.211 IP Netmask: 255.255.255.128 IP Gateway: 9.51.8.132 BOOTP Server: 0.0.0.0

Updating the adapter’s firmware
To update the adapter’s firmware, you send a file to the adapter’s flash memory, overwriting the existing flash memory. This process is also known as flashing the adapter. You can update the firmware by using TFTP. To use TFTP, do the following:
1 Get the flash file you need by contacting your vendor.
2 Do NOT turn off (or reset) the adapter or printer during the flash process. This may damage the adapter. The adapter resets itself after the flash process is finished.
3 TFTP the file to this destination: /dev/flash.
Using the protocols

After you have set the TCP/IP information, you can change it using any of the ways you set the information, or by doing one of the following: • Use telnet to change the information.
1 Type the following at the command prompt:
telnet ip.address -p 9000
where ip.address is the IP address you’re using, such as 9.51.8.231.
2 Follow the instructions on the screen. • FTP a file to the param directory.
The param directory is a special directory where you can change special TCP/IP-related parameters. The format of this file is:
This section helps you correct problems you may encounter while using the adapter on a TCP/IP network. It describes the problems when:
Troubleshooting · TCP/IP networks

The server does not appear to be sending jobs to the network printer you specified. Jobs are in the queue and appear to be waiting for a long time.
The printer is probably busy receiving jobs from other servers or from other links.
1 Double-check the printer to be sure that it is working properly.
2 Print a setup page from the adapter. • Press the Test button until the Test light comes on. The Data light comes on, and the adapter sends a setup page to the printer.
If the page prints, then the connection between the adapter and the printer is working correctly. If the page does not print, check all the physical connections.
3 Look at the setup page. Make sure the IP protocol is active.
Troubleshooting · Solution

The printer is not receiving print jobs.
1 Make sure the printer is turned on and is ready.
2 Make sure that the adapter is installed properly in the printer. To check this, print a test page. (This is the test page that you printed when you first set up your printer.) The adapter will be in the list of attachments on the test page. Instructions for printing the test page can be found in your printer’s documentation.
3 Print a setup page from the adapter. • Press the Test button until the Test light comes on. The Data light comes on, and the adapter sends a setup page to the printer.
If the page prints, then the connection between the adapter and the printer is working correctly. If the page does not print, check all the physical connections.
4 Look at the setup page. Make sure the IP protocol is activated.
5 Make sure that the LAN cable is plugged into the printer and into the LAN, and that the network is working properly.
6 Make sure that the print queues are properly defined and that the print server is functioning correctly. Refer to the documentation for your operating system for help.
If the IP Protocol is enabled, check the IP address, netmask, and gateway to be sure they are correct. (You can check these on the printer’s control panel or from other Network Printer Utilities.) Also, verify all physical connections between the adapter, the printer, and the LAN.
Troubleshooting · TCP/IP networks · Solution

Different patterns of lights may appear on the Network Adapter. These patterns indicate to you various problems that may occur, to help you diagnose them. In the following table, find the pattern of lights that is displayed on your adapter, then follow the action described. If you need to call for service, be sure to make a note of the light pattern before you call.
off on off Ready.(Idle.)
off on blinking Processing. Normal operation. Data is being received from a host, or sent to a printer.
on off off Testing. The first light pattern indicates that you have pressed the Test button.
off on blinking The second light pattern indicates that a setup page is being sent from the adapter to the printer.
off on blinking Updating flash code. The first light pattern indicates that the flash code is being downloaded to the adapter.
blinking blinking blinking The second light pattern occurs while the adapter is updating the flash code. Make sure the adapter stays plugged in.
After the adapter goes through its normal start-up tests, it returns to its Ready state.
off blinking on Network error. Check all connections to the network. For example, make sure the network cables are connected.
off blinking off Software error. Turn the printer off then on to reset the adapter. Then try to re-send the print job. If this error persists, call for ser- vice.
on blinking on Flash error. Turn the printer off then on to reset the adapter. If the error persists, call for service.
Troubleshooting

Introduction Thank you for buying this multi-protocol adapter. The information in this chapter helps you install and set up your utilities to print to an adapter.
To install the Network Adapter and start its operation, you need the following:
1 Microsoft’s Windows 95 operating system installed on your computer.
2 The MarkVision Printer Utility for Windows 95. Support for this Network Adapter is built into the MarkVision utilities. You do not need separate Network Printer Utilities; everything comes with MarkVision. The MarkVision Printer Utility for Windows 95 is shipped on CD-ROM or diskettes with many printers.
3 One of the following installed on your network: • Be sure that the adapter is installed in the printer, and the network cable is connected. See your printer documentation if you need help.
To check a current firmware level, contact your point of purchase
To check your firmware level, see “Step 2: print a setup page” on page 2-3.
If you already have MarkVision running under Windows 95, skip this section. Go to "Configuring the adapter" on page 3-2.
Windows 95 · operating

If you received the MarkVision Utility with your printer, follow the instructions on the diskette respectively CD-ROM to install it. Be sure you read the README.TXT file (using WORDPAD or DOS EDIT) for last-minute information about the utility.
You must set up the adapter to process Windows 95 print jobs. The information in this section should help you. In addition, please consult the on-line help for the latest information available. The Network Adapter can process jobs from many different environments (for example, from NetWare networks and TCP/IP networks).
You can use NetWare in a Windows 95 environment.
Make sure your Windows 95 desktop is set up to run NetWare jobs. From the Control Panel:
1 Select Network.
2 Make sure one of these is running:
a Microsoft client for NetWare Networks
b Microsoft client with NDS upgrade
c 16-bit Novell client
d Novell client 32
Configuring the adapter · Prerequisites

1 Log on as an administrator or print operator.
2 Start MarkVision.
MarkVision searches for bidirectional printers and displays the search results in its main window.
The NetWare protocol must be turned on in the adapter for the adapter to process NetWare jobs.
1 In the MarkVision printer window, double-click on the adapter port you wish to configure for NetWare.
2 Look at the tabs that appear. If the NetWare settings tab is present, the protocol is on. If the NetWare settings tab is absent or grayed out, then you must turn the protocol on. • Use the on-line help for information.
1 In the MarkVision printer window, double-click on the adapter port that you wish to configure.
2 Click the Adapter Settings tab.
3 Set or verify all the general parameters for the adapter and port (such as address, and so forth).
4 If you want this Network Adapter to process TCP/IP settings as well, you may want to set the TCP/IP address, netmask, and gateway from this Adapter Settings tab. Simply click the Advanced Settings button, then set the TCP/IP information in the dialog box that appears.
5 When you finish, select Apply.
You must disable the adapter port to avoid interfering with incoming NetWare jobs.
1 Click the NetWare Settings tab.
2 Disable the port by making sure there is no checkmark in the Port Enabled box.

1 On the NetWare Settings tab, set the print mode to PSERVER or NPRINTER/RPRINTER. If you need help deciding which mode to use, see “Deciding whether to use NPRINTER/RPRINTER mode or PSERVER mode” on page 5-7.
2 Fill in the other fields on the dialog box to configure the port for NetWare print jobs. If you need help, click the question mark button, then click the field.
3 After you finished setting all the fields on this tab, click Apply.
4 On the NetWare Settings tab, click Manage Queues. You’ll be setting up queues for the adapter to service.
5 In the Queue Manager dialog box, select existing queues or create new queues for the adapter to service. If you need help, click the question mark button, then click the field.
6 When you finish setting up queues, click OK.
7 If you are using the Network Adapter, on the NetWare Settings tab, click Advanced Settings. Fill in the fields. If you need help, click the question mark button, then click the fields you need help on.
8 After you finished with the Advanced Settings dialog, click OK.
1 On the NetWare Settings tab, enable the adapter port by putting a check- mark in the Port Enabled box.
2 Click Apply to activate your changes.
3 MarkVision asks if you want to reset. Click Yes if you want to start using the adapter for NetWare print jobs now.
Congratulations! Your adapter is ready to process NetWare print jobs.
Configuring the adapter

You can use TCP/IP in a Windows 95 environment.
Make sure your Windows 95 desktop is set up to run TCP/IP jobs. From the Control Panel:
1 Select Network.
2 Make sure TCP/IP is running. If it is not:
a Select Add.
b Select Protocol.
c Select the Microsoft TCP/IP option.
1 Make sure you know the adapter’s community name. The default is public.
2 Start MarkVision.
3 In the MarkVision printer window, double-click on the adapter port that you wish to configure.
1 If you are using NetWare protocol as well as TCP/IP, you can quickly set this information within MarkVision.
a Click the Adapter Settings tab.
b Click the Advanced Settings button.
c Set the TCP/IP information in the dialog box that appears.
d When you finish, select Apply.
2 If you are not using NetWare, go to “Step 3: set the IP address, netmask, and gateway” on page 2-5, or use the MarkVision on-line help for instructions.

If you use version 1.06 follow the steps described below or refer to the Operation Guide of MarkVision coming with the printer you purchased. By design, TCP/IP devices do not broadcast their presence (as, for example, NetWare objects do). Because of this design, MarkVision has no way to automatically find an adapter and monitor it. Therefore, you must inform MarkVision about adapters that you want it to show in its list. To add an IP adapter to the list in the MarkVision window:
1 In the MarkVision printer window, click on the Configure option in the pull-down menu.
2 Click TCP/IP Settings.
The list of TCP/IP adapters that you want MarkVision to enumerate appears. (The box is empty until you add the first TCP/IP adapter.)
3 Click Add Adapter.
4 Fill in the IP address that you defined in the previous step.
5 Fill in the community name. The name you specify must match the community name stored inside the adapter. The original community name is public.
6 Fill in the host name field with any name you choose. This is the name that you use to refer to the adapter.
7 Click OK.
MarkVision saves the changes in an ASCII file named !MVNETIP.INI.
1 In the MarkVision printer window, double-click on the adapter port that you wish to configure.
2 Click the Adapter Settings tab.
3 Set or verify all the general parameters for the adapter and port (such as address and so forth).
4 Click Apply.
Configuring the adapter

The IP protocol must be turned on in the adapter; otherwise, the adapter will not recognize or process IP print jobs.
a On the Adapter Settings tab, click Advanced Settings.
b In the Advanced Settings dialog box, look at the Set Active Protocols
group. Make sure the TCP/IP box has a checkmark in it.
c When you finish, select Apply.
Congratulations! The adapter is ready to process TCP/IP print jobs. For more information about modifying the list of adapters, continue with "To process Point to Point printing (LexIP)" on page 3-8.

Point to Point is an easy way for you to print from a Windows 95 workstation to a network-attached printer. It’s especially useful in small organizations or departments because you can print without having a server or a network operating system (such as NetWare) installed. The following drawing shows how print jobs move from a workstation using Point to Point.
Printer Attached to network with internal Network adapter card.

MarkVision provides a way for you to print to a network printer when your network uses Microsoft TCP/IP. If you run TCP/IP on your network, you can install Point to Point with MarkVision. Then you can print from Windows applications to a network printer. Point to Point is supported by the adapters. MarkVision can monitor the network printer.
Prerequisites:
1 You must have MarkVision installed on your workstation.
2 The Microsoft TCP/IP DLL must be installed on your workstation. If it is not installed, use Custom install to select TCP/IP Network Support.
3 The TCP/IP protocol must be bound to the network interface card in your Windows 95 computer. Consult your Windows 95 online HELP for binding an adapter to a protocol (look for Binding in the HELP index), or see the section on “To process TCP/IP print jobs“ on page 3-5.
Configuring the adapter

How to configure for TCP/IP protocol:
1 Assign a TCP/IP address, netmask, and gateway for the adapter.
a If you have NetWare running on your network, you can quickly initia-
lize the TCP/IP address, netmask, and gateway for the new adapter. Otherwise, you can use BOOTP.
2 Add the adapter to the list of TCP/IP adapters you want to see in the MarkVision printer window.
a In the MarkVision printer window, click Configure from the pull-down
menus.
b Click TCP/IP Settings. The list containing TCP/IP adapters that you want
MarkVision to monitor appears. (The box is empty until you add the first TCP/IP adapter.)
c Click Add Adapter.
d In the IP address field, enter the TCP/IP address you defined earlier
(step 1).
e Fill in the Host Name field with any name you choose. This is the name
that you use to refer to the adapter. (Other users can have their own host names for the same adapter.)
f Fill in the Community Name. The name you specify must match the
community name stored inside the adapter. The original community name is public. The community name is case sensitive.
g Click OK.
3 Set (or verify) the protocol-independent parameters.
a In the MarkVision printer window, double-click the adapter port you
want to configure.
b Click the Adapter Settings tab.
c Enter information in the fields to set the various protocol-independent
parameters.
4 Verify the TCP/IP protocol is turned on in the adapter.
a Still using the Adapter Settings tab, click Advanced Settings.
b Make sure the TCP/IP check box in the Set Active Protocols group has
a check mark in it.

How to print Point to Point:
1 Create the printer object:
a In Windows 95, click Start, then click Settings, then Printers.
b Double-click Add Printer to define the printer you want to use.
c Choose LOCAL (not NETWORK) printer.
d Select the appropriate manufacturer and printer.
e Choose any port (LPT or COM or FILE). Later you change the port to
a logical network port.
2 Assign the printer object to the physical printer.
a After the printer object is added to your printer container, highlight
it’s icon. Optionally, double click on it with the right mouse button.
b Click File, then Properties, then Details tab, then Add Port.
c Click Others, then click Network Printer Monitor, then click OK.
d Select the printer you want to use. The printer list was generated using
MarkVision.
e Specify a logical port name to assign to the printer. Use a port name that
is meaningful to you. Click OK.
a To print a test page, use Windows 95, then Start, then Settings, then
Printer, then File, then Properties, then General tab, then Print Test Page.
b To print from a Windows application, select Print as usual.
Configuring the adapter · 3 Print

Peer to Peer is an easy way for you to print from a Windows 95 workstation to a printer locally connected to a network attached personal computer. A Peer to Peer network consist of personal computers linked together so that a computer can share the hardware and software resources of the other computers on the network. You can print from Peer to Peer in a Windows 95 environment. The following drawing shows how print jobs move from a workstation using Peer to Peer.

MarkVision provides a way for you to print to a local printer connected to a network attached computer when your workstation uses Windows 95 as an operating system. Peer to Peer requires that print sharing be enabled on the computer that has the locally attached printer and that the printer be shared. MarkVision requires Peer to Peer to be installed to monitor the printer.
1 The standard Windows 95 Client for Microsoft Networks client must be installed to provide the ability to logon to the Peer to Peer network. This is the standard configuration.
2 The standard Windows 95 File and Print Sharing for Microsoft Networks must be installed and configured to allow the workstation to share its printers across the network.
3 In order for MarkVision to monitor the printer it is required as a minimum that the following components are custom installed.
a MarkVision Printer Utility. b MarkVision Sound and Default Setup files. c MarkVision Peer to Peer client Support. d MarkVision Server Support.

How to print Peer to Peer:
How to share your printer:
1 To share your locally attached printer with other workstations click the Start button on the Windows 95 screen.
2 Point to Settings, and then click Printers.
3 In the Printers window, click the printer you want to share.
4 On the File menu, click Sharing.
5 Click the options you want.
How to enable print sharing:
1 If your workstation is set to use a network, the Network Neighborhood icon appears. In Network Neighborhood, locate and double-click the com- puter where the printer you want to use is located.
2 Double-click the printer icon in the window that appears.
3 To set up the printer, follow the instructions on the screen.
How to configure MarkVision for Peer to Peer:
1 In the MarkVision printer window, click Configure (pull down menu).
2 Click Peer to Peer Settings.
3 In the dialog that appears, you can specify which Peer to Peer workgroups and computers you are interested in. The locally attached printers in these workgroups/computers will be displayed in the MarkVision printer window.
4 If you want MarkVision to include your defaults workgroup in the next refresh cycle, make sure the box is checkmarked.
5 If there are any other workgroups or computers outside of your default workgroup that you want included in the next refresh cycle, specify these in the fields provided. Right click the selected field if you need help.
6 Click Done to save your changes.
7 Check the MarkVision printer window for Peer to Peer printers. Look in the CONNECTION column for a string similar to \\JohnsComputer \Q25 (for example).
Configuring the adapter

Troubleshooting This section helps you correct problems you may encounter while using Network Adapters. To use this section, find a Symptom that describes the problem you are having, then follow the Solution listed below.
Adapter unable to find the net- work printer
"Adapter unable to find network prin- ter" on this page.
Print jobs stay in the queue "Print jobs stay in the queue" on page 3-14.
Print jobs are ending prematurely "Print jobs are ending prematurely" on page 3-14.
While configuring the adapter, the utility is unable to find the network printer (that is, the network printer does not appear in the adapter list).
1 Make sure the printer is turned on and is Ready.
2 Make sure the adapter is installed properly.
To find out, print a test page. (This is the test page that you printed when you first set up your printer.) The adapter will be in the list of attachments on the test page. Instructions for printing the test page are in your printer’s documentation.
Make sure the protocol you’re using is activated.
a On the Adapter Settings tab, click Advanced Settings.
b In the Advanced Settings dialog box, look at the Set Active
Protocols group. Make sure the TCP/IP box has a checkmark in it.
c After you finished, select Apply.
3 Make sure the status light on the adapter is on.
4 Make sure all routers are configured properly.

The server does not appear to be sending jobs to the network printer you specified.
1 The printer is probably busy receiving jobs from other servers or from other links. Check the printer to be sure it is working properly.
2 Make sure the adapter is installed properly.
To find out, print a printer test page. (This is the test page that you printed when you first set up your printer.) The adapter will be in the list of attachments on the test page. Instructions for printing the test page can be found in your printer’s documentation.
3 Print a setup page from the adapter. If the page prints, then the connection between the adapter and the printer is working correctly. If the page is not printed out, check all the physical connections. • Press the Test button until the Test light comes on. The Data light blinks, and the adapter sends a page to the printer.
4 Look at the setup page. Make sure the protocol is active.
5 Make sure you’ve configured the adapter properly. If you need help, review the section(s) in this chapter according to your needs.
6 Make sure the LAN cable is connected to the server while the print job is active.
Print jobs are partially printed; the printer stops printing in the middle of a page.
The adapter stopped receiving data because it believed it had reached the end of a print job. • If you’re using a PostScript printer, check the printer driver’s configuration. Increase the print job time-out value there. Try your print job again.
Troubleshooting · Solution · Solution

Different patterns of lights may appear on the Network Adapter. These patterns indicate various problems that may occur, to help you diagnose them. In the following table, find the pattern of lights that is occurring on your adapter, then follow the action described. If you need to call for service, be sure to make a note of the light pattern before you call.
Test Status Data Description/Action
off on off Ready (Idle).
off on blinking Processing. Normal operation. Data is being received from a host, or sent to a printer.
on off off Testing. The first light pattern indicates that you have pressed the Test button.
off on blinking The second light pattern indicates that a setup page is being sent from the adapter to the printer.
off on blinking Updating flash code. The first light pattern indicates that the flash code is being downloaded to the adapter.
blinking blinking blinking The second light pattern occurs while the adapter is updating the flash code. Make sure the adapter stays plugged in.
After the adapter goes through its normal start-up tests, it returns to its Ready state.
off blinking on Network error. Check all connections to the network. For ex- ample, make sure the network cables are connected.
off blinking off Software error. Turn the printer power off then on to reset the adapter. Then try to re-send the print job. If this error persists, call for service.
on blinking on Flash error. Turn the printer power off then on to reset the adapter. If the error persists, call for service.

Troubleshooting

Introduction Thank you for buying this multi-protocol adapter. This chapter explains how to set up and use your printer on Windows NT operating systems. To do this, you should have a basic working knowledge of Windows NT.
The following methods are used to print in a Windows NT environment.
Before you can use the adapter, you need to set it up. Setup involves a few simple steps: 1. Checking the physical connections. 2. Printing a setup page to use while you set up the adapter. 3. Setting the adapter’s IP address, netmask, and gateway. 4. Verifying the setup. If you need help, see “Using TCP/IP networks” on page 2-1.
This section explains how to create your printer under Windows NT 3.51 operating systems.
Windows NT operating

Printing under Windows NT 3.51
If you would like to print with using lpr protocol, you need to install “TCP/IP Network Printing Support” on your Windows NT operating system.

a. In the Printer Name field, type the name that you want to give to
the printer.
b. From the Driver field, pick a driver that you want to use with this
printer.
c. In the Print To list box, select Other. The Available Print Monitors
dialog box appears.

Printing under Windows NT 3.51

Windows NT operating systems

a.In the Name or address of host providing lpd field, type the host
name or IP address that you set to the adapter.
b.In the Name of printer on that machine field, type the name that
you want to give to the printer.

My printer name

Printing under Windows NT 4.0
This section explains how to create your printer under Windows NT 4.0 operating systems.
If you would like to print using the lpr protocol, you need to install “Microsoft TCP/IP Printing” on your Windows NT. If you would like to print using the Network Port, you need to install “MarkVision for Windows NT 4.0” on your Windows NT.
1.In the Windows NT user interface, click Start, then click Settings, then click Printers. 2.Double-click Add Printer.












Printing under Windows NT 4.0
3.Select My Computer, then click Next. The Available ports dialog box appears.

Windows NT operating systems

















Printing under Windows NT 4.0
a. In the Name or address of server providing lpd field, type the host
name or IP address that you set to the adapter.
b. In the Name of printer or print queue on that server field, type the
name that you want to give to the printer.






My printer name

Printing under Windows NT 4.0



Windows NT operating systems








On the CD-ROM or floppy disks included in your printer package, you will also find information on how to set up a printer using a network port (TCP/IP ports).

Printing under Windows NT 4.0

Introduction The following instructions work for Network Adapters. To install this Network Printer Utility, you need to have a basic working knowledge of Novell NetWare networks, especially the Print Server software.
Follow the steps below to prepare for the installation.
1 Look at the README.1ST file on the NetWare Network Adapter: Net- work Printer Utility diskettes respectively CD-ROM before you begin to set up the utility. This file may contain updates about system requirements or procedures that were not available when this guide was published.
2 Make backup copies of your new diskettes. See your operating system documentation if you need help.
Prerequisites:
2 The NetWare Network Adapter: Network Printer Utility diskettes respectively CD-ROM.
3 One of the following installed in your network: • A Network Adapter. Make sure the adapter is installed in the printer, and the network cable is connected. Instructions for installing the adapter are located in your printer’s documentation.
NetWare

You can install the Network Printer Utility under Windows 3.1 (following) or Windows 95 (see Chapter 3). Follow the following steps to install the utility in a Windows 3.1 environment. You may install the utility as a Stand-alone product, in the program group you choose. To install the utility:
1 Insert the NetWare Network Adapter Network: Network Printer Utility diskette respectively CD-ROM for Windows 3.1 into drive A.
2 From the Program Manager window, select File from the menu bar, then select Run The Run dialog box opens.
3 Type the following in the text box, when installing from diskette:
a:\instwin
4 Select OK.
The Install dialog box opens. It looks similar to the following:

5 Follow the instructions on the screen.
Installing the utility

Starting the network printer utility
Before you can send print jobs to the adapter, you must start the utility and configure the adapter. You can start the Network Printer Utility from wherever you installed it under Windows 3.1. The following screenshot illustrates the way.

Ways to Start the Network Printer Utility To start the utility:
1 Log in to NetWare as a user with administrator privileges.
2 Start the utility. • Go to the Program Group and double-click the Network Printer Utility icon. The icon is shown in the screenshot above.
NetWare · networks

When you start the utility, its adapter list appears. This list shows all adapters that answer a broadcast. You can’t print to the adapters yet, because you have not set them up to receive jobs. You will use the Network Printer Utility (and PCONSOLE, if you prefer) to configure the adapters and monitor them.
The adapter list looks similar to this:

To work with the utility:
2 Then use the menu bar to work with the selected adapter. Notice that the list has six items on the menu bar: File, View, Setup, Printer Status, Options, and Help.
For example, to set up an adapter, you first highlight the adapter, then select Setup from the menu bar. The utility has six pull-down menus, on the menu bar. Some of the functions that you can do from the pull-down menus are available for only specific adapters. The functions that aren’t available are grayed-out on the screen.
Using the utility

The menu items:
Printer Status Options Help

Setting up the adapter
Now that you have installed and started the utility, you need to set up the adapter so that you can send print jobs to it.
To set up the adapter, you may use either: • the Network Printer Utility alone.
This utility provides all of the functions you need to set up the adapters in a NetWare environment. The utility is designed to meet the needs of a network administrator and can only be started by a person who has network supervisory rights.
Functions that you may be accustomed to doing from PCONSOLE (such as setting up print queues) can be managed from the Network Printer Utility.
If you are accustomed to using PCONSOLE or NWADMIN to set up NetWare components or objects, you may continue to do so. Then use the Network Printer Utility to configure the adapter.
1 From the Network Printer Utility’s menu bar, select Help, (even if you want to set up the adapter using PCONSOLE and this utility.)
2 From the Help’s Table of Contents, select Configuring the Adapter.
3 Select the section that is relevant to you.
Sections devoted to NetWare 3.x and 4.x are listed, including information about PCONSOLE methods of setting up the adapter.

Setting up the adapter
If you need help deciding whether to use PSERVER or NPRINTER/ RPRINTER, continue with “Deciding whether to use NPRINTER/ RPRINTER mode or PSERVER mode” on this page.
4 Print those instructions and follow them to set up your adapter.
What to do next
When you have finished setting up the adapter, continue with “Verifying the adapter setup” on page 5-11.
When configuring your adapter, you’ll have to set it up in either NPRINTER/ RPRINTER or in PSERVER mode.
How NPRINTER/RPRINTER mode works
A network adapter configured in NPRINTER/RPRINTER mode acts as a remote printer. This remote printer receives print jobs from a print server. The print server, a program called PSERVER.NLM running on a NetWare server, obtains print jobs from a queue and sends them to the remote printer. The following diagram shows how NPRINTER/RPRINTER mode works.

NetWare · networks · Remote printer

Setting up the adapter
How PSERVER mode works
An adapter set up in PSERVER mode acts as a print server attached to NetWare servers. This adapter obtains print jobs from queues located on one or more servers. PSERVER adapters actually log into NetWare servers as a NetWare client and, therefore, require one NetWare user license slot per PSERVER device. The following diagram shows how PSERVER mode works.

Adapters are fully supported in NetWare 4 NDS, using either NPRINT or PSERVER mode. You do not need to use bindery emulation in either mode.
NPRINT mode in NetWare 4 NDS

Setting up the adapter
Notes about printing performance: • Many people prefer to configure their network adapters in PSERVER mode, because they are used to it, since in early versions of NetWare PSERVER performance was significantly better than NPRINTER/RPRINTER performance. This performance difference is smaller for NetWare 4.x. The actual print job throughput is affected by many other factors such as topology, job size and content, and network adapter settings. Under many circumstances, NPRINTER mode provides an excellent NetWare 4.x NDS solution.
PSERVER mode in NetWare 4.x NDS
packets. Packet size for data transmitted in SPX is 512 bytes. – In PSERVER mode, NetWare uses IPX to transfer packets. Packet
size for data transmitted in IPX is up to 1 Kbyte for Ethernet networks. Because of this difference in packet size, PSERVER mode may be faster than NPRINTER/RPRINTER mode. Please note, however, that the actual IPX packet size is negotiated by the client application. This actual IPX packet size is often less than the maximum because of packet size limitations of gateways and routers. If printing is a significant part of your network traffic, and if network traffic is a proven concern for your network, you may find it better to use the adapters in PSERVER mode. Disadvantage of using PSERVER mode in NDS: • Requires a NetWare server user license for each PSERVER device
RPRINTER versus PSERVER in NetWare 3.x
Adapters are fully supported in NetWare 3.x, using either RPRINTER or PSERVER mode.
NetWare · networks

Setting up the adapter
RPRINTER mode in NetWare 3.x
PSERVER mode in NetWare 3.x
packets. Packet size for data transmitted in SPX is 512 bytes. – In PSERVER mode, NetWare uses IPX to transfer packets. Packet
size for data transmitted in IPX is up to 1 Kbyte for Ethernet net- works. Because of this difference in packet size, PSERVER mode may be faster than NPRINTER/RPRINTER mode. Please note, however, that the actual IPX packet size is negotiated by the client application. This actual IPX packet size is often less than the maximum because of packet size limitations of gateways and routers. If printing is a significant part of your network traffic, and if network traffic is a proven concern for your network, you may find it better to use the adapters in PSERVER mode. • Connects to several file servers and supports many queues: – Network Adapter connects to as many as 16 file servers, with a
total of 32 queues per adapter, distributed any way you want among the servers Disadvantage of using PSERVER mode in NetWare 3.x: • Requires a NetWare server user license slot for each PSERVER device

Setting up the adapter
What to do next
Congratulations! Your adapter is ready to work for you. You have finished setting up the adapter. To make sure you can print to it, you should test it.
To verify that you did everything correctly and that you can print with the adapter and the utility, do the following:
1 Reset the adapter. If you need help, follow these steps.
a From the utility’s adapter list, select the adapter whose setup you want
to verify.
b On the utility’s menu bar, select Setup/Customized.
c Select Reset Adapter.
2 Check the list of servers under Options to be sure the servers you set up in the previous step are listed there. If you need help, follow these steps:
a On the utility’s adapter list, select the adapter whose servers you want
to check.
b From the utility’s menu bar, select Options.
c Select Show Adapter’s Servers.
d Check the list of network servers. Make sure the server you want the
3 Print a page to a queue. If you need help, follow these steps:
a From the utility’s menu bar, select File.
b Select Print.
c Select To Queue. On the Print List to Queue dialog box, select the file
server, select the queue, and then choose Print Adapter List.
If the page doesn’t print, review this section. Be sure the adapter is configured properly, is enabled, and that all the queues are set up correctly. Make sure you are logged into the server.
NetWare · networks

This section helps you to correct problems you may encounter while using the Network Adapters regarding their symptoms:
While configuring the adapter, the utility is unable to find the network printer (that is, the network printer does not appear in the adapter list).
1 Make sure the printer is turned on and is Ready.
2 Make sure that the adapter is installed properly. To check this, print a test page. (This is the test page that you printed when you first set up your printer.) The adapter will be in the list of attachments on the test page. You can find instructions for printing the test page in your printer’s documentation.
3 Make sure that:
4 Make sure all routers are configured properly.
5 Make sure the workstation network drivers are up to date.
6 From the Network Printer Utility menu, select View/Search for Adapters by/Entire Network.
The server does not appear to be sending jobs to the network printer you specified.
Troubleshooting · Solution

1 The printer is probably busy receiving jobs from other servers or from other links. Check the printer to be sure it is working properly.
2 Make sure the adapter is installed properly. To check this, print a test page. (This is the test page that you printed when you first set up your printer.) The adapter will be in the list of attachments on the test page. You can find instructions for printing the test page in your printer’s documentation.
3 Print a setup page from the adapter. If the page prints, then the connection between the adapter and the printer is working correctly. If the page does not print, check all the physical connections. • Press the Test button until the Test light comes on. The Data light blinks, and the adapter sends a page to the printer.
4 Look at the setup page. Make sure the NetWare protocol is active and the proper frame types are set.
5 Check the Network Printer Utility to make sure you have:
a Configured the adapter. If you need help, go to “To set up the
adapter” on page 5-6.
b Enabled the port. If you need help, use the utility’s on-line help.
6 If you are using PSERVER mode, make sure you have:
a Defined the adapter as a print server. If you need help, go to “To set
up the adapter” on page 5-6.
b Defined print queue names. If you need help, use the utility’s on-line
help.
c Assigned the adapter’s login name to service the print queue. If you
need help, use the utility’s on-line help.
d Used Novell’s PCONSOLE utility to make sure the queue is not being held.

7 If you are using RPRINTER mode, make sure you have:
a Defined a NetWare server for the adapter to service. If you need help,
go to the utility’s on-line help.
b Defined print queue names. If you need help, go to the utility’s on-
line help.
c Defined the adapter as a remote printer. If you need help, go to the
utility’s on-line help.
d Used Novell’s PCONSOLE utility to make sure the queue is not being held.
e Unloaded the print server, or rebooted the computer, after you configure the
utility. (After configuration, you will be prompted to unload PSERVER.NLM or reboot your computer. Be sure you do so.) This is necessary and a normal function of Novell’s RPRINTER mode. If you need help, consult your RPRINTER documentation.
8 If some files stayed in the queues without being printed, then the LAN cable was probably disconnected from the server while the print job was active. Reconnect the cable, reset the adapter, and try again.
Troubleshooting

Different patterns of lights may appear on the Network adapter. These patterns indicate various problems that may occur, to help you diagnose them. In the following table, find the patterns of lights that is occurring on your adapter, then follow the action described. If you need to call for service, be sure to make a note of the light pattern before you call.
Test Status Data Description/Action
off on off Ready (Idle).
off on blinking Processing. Normal operation. Data is being received from a host, or sent to a printer.
on off off Testing. The first light pattern indicates that you have pressed the Test button.
off on blinking The second light pattern indicates that a setup page is being sent from the adapter to the printer.
off on blinking Updating flash code. The first light pattern indicates that the flash code is being downloaded to the adapter.
blinking blinking blinking The second light pattern occurs while the adapter is updating the flash code. Make sure the adapter stays plugged in.
After the adapter goes through its normal start-up tests, it returns to its Ready state.
off blinking on Network error. Check all connections to the network. For example, make sure the network cables are connected.
off blinking off Software error. Turn the printer power off then on to reset the adapter. Then try to re-send the print job. If this error persists, call for service.
on blinking on Flash error. Turn the printer power off then on to reset the adapter. If the error persists, call for service.
Troubleshooting · NetWare · networks

Troubleshooting

Introduction For your convenience, you can view or change some information about the adapter from the control panel of the printer. You can use the printer control panel to set the IP address, netmask and/or gateway for TCP/IP networks.

1 Turn the printer power On (|).
2 Use the printer control panel to select one of the following settings. Consult your printer documentation to learn the menu path for your specific printer, or scroll through the control panel menus until you find it.
For further details on the use of the printer control panel see the corresponding chapter in the Printer User´s Manual.
3 Press READY to return to ready status.
Table A.1 IP Protocol
Menu Item Values Description
Using this menu item, you can set BOOTP on or off.
You should select No if you have set the IP address, netmask, and/or gateway through the printer’s control panel and you want these settings to always apply to this adapter.
You should select Yes if you want the adapter to automatically find its BOOTP server to get its IP address, netmask, and/or gateway.
IP Address Using this menu item, you can set the IP address directly on the printer’s control panel. When you do, be sure to set Enable BOOTP to No. If Enable BOOTP is set to Yes and you turn the printer off and on again, the adapter will search for a BOOTP server and will use the address stored in that file instead of this address.*NOTE
IP Netmask Using this menu item, you can set the IP netmask directly through the printer’s control panel. When you do, be sure to set Enable BOOTP to No. If Enable BOOTP is set to Yes and you turn the printer off and on again, the adapter will search for a BOOTP server and will use the netmask stored in that file instead of this one.*NOTE
IP Gateway Using this menu item, you can set the IP gateway directly through the printer’s control panel. When you do, be sure to set Enable BOOTP to No. If Enable BOOTP is set to Yes and you turn the printer off and on again, the adapter will search for a BOOTP server and will use the gateway stored in that file instead of this one.*NOTE

Introduction · Printer control panel

Introduction

This glossary contains terms specific to local area networks (LANs) and the use of the Network adapters.
A adapter address. The manufacturer’s identification, or the user-defined identification, of an adapter. The adapter address is sometimes also used as the default nickname or login name.
B BOOTP. See BOOTstrap protocol (BOOTP).
BOOTstrap Protocol (BOOTP). A TCP/IP protocol that enables a workstation to find its IP address.
D data stream. Print data and control information flowing from a host system (computer) to the printer, from beginning to end without interruption.
DLC protocol (Data Link Control). A set of rules used by two nodes on a data link to accomplish an orderly exchange of information.
E Ethernet. A network with a bus topology that uses carrier sense multiple access with collision detection (CSMA/CD). An Ethernet network may be installed using any of three cabling systems: Ethernet 10BASE-T (using telephone twisted pair); Ethernet 10BASE2 (using RG-58 coax and also referred to as Cheapernet or Thinnet); Ethernet 10BASE5 (using AUI cable).
F file server. A computer on your network that runs the operating system software. The software controls the communication among computers attached to the network and it manages shared resources.
File Transfer Protocol (FTP). A TCP/IP protocol that transfers files from one computer to another. It is usually implemented in application programs. This is considered a better way to send files than TFTP (Trivial File Transfer Protocol) because it uses TCP instead of UDP.

Finger. A TCP/IP protocol that normally displays user information on a host computer. When used with Integrated Network Option, finger displays the status of the printer and the current print job.
firmware. Software that resides in the adapter.
flash memory. A type of ROM (read-only memory) used on all MarkNet adapters. Flash memory can be erased electronically and reprogrammed without your removing the adapter from the printer.
FTP. See File Transfer Protocol.
G gateway. The connector device between many LANs.
H host. The main computer on a network allowing all computers connected the use of data files or programs installed on it.
I ICMP. See Internet Control Message Protocol.
IEEE 802.3. A standard by the Institute of Electrical and Electronics Engineers (IEEE) for a local area network that uses the CSMA/CD access method. This standard has been popularized by Ethernet local area networks.
Integrated Network Option. The Network adapter and its utilities. This adapter is designed to be installed inside various laser printers and therefore sometimes referred to as Internal Network Adapters.
integrated port. On the Network adapter, the port physically located on the adapter. See also network port.
Internet. Worldwide networks connection via Internet routers so that information and services may be shared.
Internet Control Message Protocol (ICMP). An important part of the Internet Protocol, it describes and manages error and control messages.
Internet Protocol (IP). A standard that specifies how packets are passed through networks. It identifies the format of the packet and describes how they should be delivered in a seamless manner. Although it is a separate protocol from TCP, it is often referred to as TCP/IP because both TCP and IP protocols are often used together.

IP. See Internet Protocol .
L LAA. See Locally Administered Address.
LAN. See local area network.
LAN Connection Utility. An OS/2 utility that resides on a network server used to redirect printer or plotter data from its intended destination to a printer or plotter on a LAN-attached adapter.
LAN segment. Any portion of a LAN that operates independently of, but is connected to, the network by bridges or routers.
local area network (LAN). A computer network located within a limited geographical area of a few hundred meters.
Locally Administered Address (LAA). An address that a network administrator assigns to a network adapter on the LAN. Administrators may assign the adapter any address that they wish (within certain constraints). Many administrators use the LAA to give the adapter a meaningful address in their workplace (for example, assigning the adapter an address that identifies its location).
lpd. Line printer daemon. Allows the use of remote printing functions under TCP/IP. This software registers the print document sent from a computer. It is a background process that runs all the time.
lpd print service. UNIX utility that receives print jobs from remote TCP/ IP hosts.
LPT (Line PrinTer). A representation of one of the logical ports (for example, LPT1) on a personal computer.
Management Information Base (MIB). A database used to manage a network and the machines based on RFC 1213, is an example of MIB. The MIB describes information specific to the Network Adapter and the printers.
MIB. See Management Information Base.
Glossary

N netmask. A bit mask that specifies the local network portion of an IP address, allowing you to logically subdivide a network.
NetWare. A family of LAN operating systems that can join PCs and Apple Macintosh computers. It supports a large number of topologies including Ethernet.
network port. The port physically located on the adapter. It eliminates the need to use the parallel and serial ports on the printer. The network port is used to connect to a LAN. See also integrated port.
network printer. A printer used on a network. In this guide, it refers to a printer connected to an adapter, receiving jobs as they are sent to the printer by the adapter.
Network Printer Utility. A user interface that allows you to configure print servers and the adapter settings to the network.
nickname. A name that a network administrator assigns to the adapter. It is used to identify the location of the printer.
NLM. Novell NetWare Loadable Module. An optional process used by Novell NetWare 3.11 to add functions to a file server.
O OS/2. Operating System/2, a multitasking operating system from IBM.
P packet internet groper (PING). Software that tests whether an IP destination can be reached by sending an ICMP echo request and waiting for a reply.
PCONSOLE. Novell NetWare Print Console software. PCONSOLE allows you to control network printing, establish print servers, and set up print queues.
PING. See packet internet groper (PING).
Print Monitor Utility. In a Windows NT environment it routes print jobs from the server’s Print Manager program to the printer. In an OS/2 environment, redirects print jobs from the network to the adapter. This utility includes the basic information for installing and configuring your adapters.
print queue. A directory in the server where print jobs are stored for printing.

print server. Hardware or software (or a combination of hardware and software) that takes information from a print queue and sends it to a printer.
protected directory. A directory guarded by security software. Access is allowed only with the proper password.
protocol. A set of rules managing the communication and transfer of data between two or more network devices.
PSERVER. A Novell NetWare printing service that takes a print job and sends it to a printer assigned to a supported queue. The adapter in PSERVER mode takes the place of the Novell PSERVER process and directs print jobs from a file server queue to a printer attached to the adapter.
R remote printer. A printer attached to a workstation on a LAN that is set up to work as a shared network printer.
requester. A workstation that requests access to shared resources, such as printers or plotters, so that they appear to be running on the user’s own workstation even though they may be running somewhere on the LAN.
RPRINTER. A terminate-and-stay-resident (TSR) program that runs on a Novell workstation. This program allows a printer locally attached to the workstation (instead of the file server) to be used as a shared network printer.
The adapter in the RPRINTER mode emulates the TSR that would normally run on the Novell workstation. The adapter in RPRINTER mode is used in conjunction with the Novell PSERVER utility to direct print jobs to a printer attached to the adapter. This method does not use any Novell user login slots.
server. A device that allows people using LAN workstations to share resources such as printers/plotters on the network.
service access point (SAP). In Open Systems Interconnection architecture, the point at which the services of a layer are provided by an entity of the next higher layer.
Simple Network Management Protocol (SNMP). A TCP/IP protocol that defines how computers will exchange management information.
Glossary

SNMP. See Simple Network Management Protocol.
spooler. An intercepting program that prevents output from different sources or workstations from interfering with each of them.
T TCP. See Transmission Control Protocol (TCP).
TCP/IP. See Transmission Control Protocol/Internet Protocol.
TFTP. See Trivial File Transfer Protocol.
Transmission Control Protocol (TCP). The standard protocol that resides at the transport layer. After two computers establish a connection, TCP provides a reliable, full duplex, stream service that allows one computer to send data to another.
Therefore, many operating systems implement TCP; they also implement the IP protocol to send data across the underlying internet. Although TCP is a separate protocol from IP, it is often referred to as TCP/IP because both TCP and IP protocols are often used together.
Transmission Control Protocol/Internet Protocol (TCP/IP). The TCP and IP protocols, used together.
Trivial File Transfer Protocol (TFTP). A TCP/IP protocol that transfers files with minimum overhead and no guarantee of delivery.
U UAA. See Universally Administered Address (UAA).
UDP. See User Datagram Protocol (UDP).
Universally Administered Address (UAA). An adapter’s UAA is the factory-set default address. Network administrators may choose to set a locally administered address (LAA) for the adapter so that its address is more meaningful to their workplace.

User Datagram Protocol (UDP). The protocol that allows one computer to send a datagram (unit of data) to another. It uses the IP protocol to deliver datagrams. UDP datagrams include a protocol port number so that the sending computer can differentiate among several destinations on the remote computer.
utility. The software that came on the diskettes respectively CD-ROM with this guide.
V VAP. Value added process. An optional process used by Novell NetWare 2.2 to add functions to a file server.
Z zone. In AppleTalk, the grouping of network devices in a logical manner so that they may be easily accessed by the user.
Glossary


Please send your comments on this manual or on Fujitsu products to the following addresses:
FUJITSU COMPUTER PRODUCTS OF AMERICA, INC. 2904 Orchard Parkway, San Jose CA 95134-2022, U.S.A. TEL: (1-408) 432-6333 FAX: (1-408) 894-1709
FUJITSU ITALIA S.p.A. Via Nazario Sauro, 38, 20099 Sesto Sau Giovanni (MI), ITALY TEL: (39-2) 26294-0 FAX: (39-2) 26294-201
FUJITSU KOREA LTD. 9th Floor, Korean Reinsurance Bldg. 80, Susong-Dong, Chongro-Gu Seoul Special City, Republic of KOREA TEL: (82-2) 739-3281 FAX: (82-2) 739-3294
FUJITSU CANADA INC. 2800 Matheson Boulevard East Mississauga, Ontario L4W 4X5, CANADA TEL: (1-905) 602-5454 FAX: (1-905) 602-5457
FUJITSU NORDIC AB Kung Hans Väg 12 S-191 76 Sollentuna, SWEDEN TEL: (46-8) 626-6000 FAX: (46-8) 626-6711
FUJITSU AUSTRALIA LIMITED 475 Victoria Avenue, Chatswood N.S.W., 2067, AUSTRALIA TEL: (61-2) 410-4555 FAX: (61-2) 411-8603
FUJITSU (SINGAPORE) PTE. LTD. 75 Science Park Drive #02-06 CINTECH II, SINGAPORE 0511 TEL: (65) 777-6577 FAX: (65) 777-8794
FUJITSU DEUTSCHLAND GmbH. Frankfurter Ring 211 80807, München, F.R. GERMANY TEL: (49-89) 32378-0 FAX: (49-89) 32378-100
FUJITSU SYSTEMS BUSINESS (MALAYSIA) SDN. BHD. Fujitsu Plaza, 1A, Jalan Tandang 204 P.O. Box 636 Pejabat Pos Jalan Sultan 46770 Petaling Jaya Selangor Darul Ehsan, MALAYSIA TEL: (60-3) 793-3888 FAX: (60-3) 793-0888
FUJITSU ESPAÑA, S.A. Almagro 40, 28009 Madrid, SPAIN TEL: (34-1) 581-8400 FAX: (34-1) 581-8125
FUJITSU EUROPE LTD. 2 Longwalk Road, Stockly Park, Uxbridge Middlesex UB11 1AB, ENGLAND TEL: (44-81) 573-4444 FAX: (44-81) 573-2643
FUJITSU SYSTEMS BUSINESS THAILAND LTD. 12th Floor, Olympia Thai Tower 444 Rachadapisek Road, Samsennok Huaykwang, Bangkok 10310, THAILAND TEL: (662) 512-6066 FAX: (662) 512-6068
FUJITSU FRANCE S.A. 1, place des Etats-Unis Silic 310 94588 RUNGIS Cedex TEL: (33-1) 41-80-38-80 FAX: (33-1) 41-80-38-66
FUJITSU HONG KONG LIMITED Room 2521, Sun Hung Kai Centre 30 Harbour Road, HONG KONG TEL: (852) 827-5780 FAX: (852) 827-4724
FUJITSU TAIWAN LTD. 8th FL., NO. 170, Hung Tai Center Tun Hwa N. RD., Taipei, TAIWAN, R.O.C. TEL: (886-2) 545-7700 FAX: (886-2) 717-4644
FUJITSU ICIM LTD. Nagar Road, Pune 411 014, INDIA TEL: (91-212) 681-528 FAX: (91-212) 680-238
FUJITSU LIMITED Computer Products Business Group 1015, Kamikodanaka, Nakahara-ku Kawasaki-shi 211, JAPAN TEL: (81-44) 754-8633 FAX: (81-44) 754-8510
Fujitsu Offices




Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.