
User's Guide
Machine type(s):
Model(s):


Connect the power cord to a properly grounded electrical outlet that is near the product and easily accessible.
Do not place or use this product near water or wet locations.
Use care when you replace a lithium battery.
– Make sure to remove the topmost finisher first.
– To remove the finisher, hold the finisher on both sides, and then lift the latches to unlock the finisher. • If the printer does not have a caster base but is configured with optional trays, then remove the trays.
Use only the power cord provided with this product or the manufacturer's authorized replacement.
Safety information 7

CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the scanner, then turn the scanner off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the scanner, then turn them off as well, and unplug any cables going into the scanner.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a professional service person.
SAVE THESE INSTRUCTIONS.
Safety information 8

Learning about the scanner and printer 9
Finding information about the scanner

Learning about the scanner and printer 10
When selecting a location for the printer and the scanner, leave enough room to open trays, covers, and doors. If you plan to install any options, then leave enough room for them also. It is important to:

Learning about the scanner and printer 11




Learning about the scanner and printer 12
When configured with the printer, the scanner provides copy, fax, and scan-to-network capability for large workgroups. You can:
When the printer is converted into a multifunction device, all printer messages will be seen on the touch screen.




Learning about the scanner and printer 13

Understanding the scanner control panel 14
Understanding the scanner control panel

1 Display Lets you view scanning, copying, faxing, and printing options as well as status and error messages
3 Sleep Enables Sleep mode
The following are the statuses of the indicator light and the Sleep button:
The following actions wake the printer from Sleep mode:
4 Keypad Lets you enter numbers, letters, or symbols on the display
5 USB port Lets you insert a USB flash drive to send data or to save scanned images.
For instructions on how to use the USB port, see “Printing from a flash drive” on page 95.
6 Submit Lets you submit changes made in the scanner settings
7 Stop/Cancel Stops all scanner activity
8 Home Lets you navigate back to the home screen
Item Description

Understanding the scanner control panel 15
The colors of the Sleep button and the indicator lights on the scanner control panel signify a scanner and a printer status.

Off The scanner and the printer are off, idle or in Ready state.
Solid amber The scanner and the printer are in Sleep mode.
Blinking green The scanner and the printer are warming up or processing data.
Solid green The scanner and the printer are on, but idle.
Blinking red The scanner and the printer require user intervention.
When the scanner is turned on, the display shows a basic screen, referred to as the home screen. Touch the home screen buttons and icons to initiate an action such as copying, faxing, or scanning; to open the menu screen; or to respond to messages.
2 3 4 5


1 Change Language Launch the Change Language pop‑up window that lets you change the primary language of the scanner.
2 Copy Access the Copy menus and make copies.
3 Fax Access the Fax menus and send faxes.
4 E-mail Access the E-mail menus and send e‑mails.
5 FTP Access the File Transfer Protocol (FTP) menus and scan documents directly to an FTP server.
12 11 10

Understanding the scanner control panel 16
6 Arrows Scroll up or down.
7 Forms and Favorites Quickly find and print frequently used online forms.
8 Menu icon Access the scanner menus.
9 Bookmarks Create, organize, and save a set of bookmarks (URL) into a tree view of folders and file links.
10 USB Drive View, select, print, scan, or e‑mail photos and documents from a flash drive.
11 Held Jobs Display all current held jobs.
13 Tips Open a context-sensitive Help dialog.
14 Search held jobs Search for one or more of the following items:
A menu path is located at the top of each menu screen. This feature shows the path taken to arrive at the current menu.
Example:
Touch any of the underlined words to return to that menu. Number of Copies is not underlined because it is the current screen. If you touch an underlined word on the “Number of Copies” screen before the number of copies is set and saved, then the selection is not saved, and it does not become the default setting.
Menus > Settings > Copy Settings > Number of Copies
If an attendance message affects a function, then this icon appears and the red indicator light blinks.

Understanding the scanner control panel 17
The IP address of your network scanner is located at the upper left corner of the home screen and appears as four sets of numbers separated by periods. You can use the IP address when accessing the Embedded Web Server so you can view and remotely configure scanner and printer settings even when you are not physically near the scanner.
Example:
123.123.123.123

1 Arrows View a list of options.
2 Copy It Print a copy.
3 Advanced Options Select a copy option.
4 Home Go to the home screen.
5 Increase Select a higher value.
6 Decrease Select a lower value.
7 Tips Open a context-sensitive Help dialog.
Feature Description · Scanner IP address · Touch To

Understanding the scanner control panel 18
Save a setting.
Reset values on the screen.

Setting up and using the home screen applications 19
You can find the scanner IP address:
1 In the Run dialog box, type cmd to open the command prompt.
2 Type ipconfig, and then look for the IP address.
1 From System Preferences in the Apple menu, select Network.
2 Select your connection type, and then click Advanced > TCP/IP.
3 Look for the IP address.
The Embedded Web Server is the scanner Web page that lets you view and remotely configure scanner and printer settings even when you are not physically near the scanner.

Setting up and using the home screen applications 20
2 Open a Web browser, and then type the scanner IP address in the address field.
3 Press Enter.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Do one or more of the following: • Show or hide the icons of basic scanner functions. a Click Settings > General Settings > Home screen customization. b Select the check boxes to specify which icons appear on the home screen.
ADF Card Copy Scan and print both sides of a card on a single page using the ADF. For more information, see “Setting up ADF Card Copy” on page 24.
Bar Code Discovery Create and manage bar code templates. For more information, see “Using Bar Code Discovery” on page 26.
Card Copy Scan and print both sides of a card on a single page. For more information, see “Setting up Card Copy” on page 22.
Fax Scan a document, and then send it to a fax number. For more information, see “Faxing” on page 119.
Forms and Favorites Quickly find and print frequently used online forms directly from the scanner home screen. For more
information, see “Setting up Forms and Favorites” on page 21.
Multi Send Scan a document, and then send it to multiple destinations. For more information, see “Setting up Multi Send” on page 23.
MyShortcut Create shortcuts directly on the scanner home screen. For more information, see “Using MyShortcut” on page 23.
Scan to E‑mail Scan a document, and then send it to an e‑mail address. For more information, see “E-mailing” on page 112.
Scan to Computer Scan a document, and then save it to a predefined folder on a host computer. For more information, see “Setting up Scan to Computer” on page 146.
Scan to FTP Scan documents directly to a File Transfer Protocol (FTP) server. For more information, see “Scanning to an FTP address” on page 143.
Use To

Setting up and using the home screen applications 21
Scan to Network Scan a document, and then send it to a network shared folder. For more information, see “Setting up Scan to Network” on page 24.
Scan to Sharepoint Securely scan documents to sites housed on SharePoint servers. For more information, see “Setting up Scan to Sharepoint” on page 26.
Your scanner comes with preinstalled home screen applications. Before you can use these applications, you must first activate and set up these applications using the Embedded Web Server. For more information on accessing the Embedded Web Server, see “Accessing the Embedded Web Server” on page 19.
For more information on configuring and using the home screen applications, do the following:
1 Go to http://support.lexmark.com.
3 Click the Manuals tab, and then select the document for the home screen application.
Streamline work processes by letting you quickly find and print frequently used online forms directly from the scanner home screen.

1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Apps > Apps Management > Forms and Favorites.
3 Click Add, and then customize the settings.
Use To · Use To

Setting up and using the home screen applications 22
4 Click Apply.
To use the application, touch Forms and Favorites on the scanner home screen, and then navigate through form categories, or search for forms based on a form number, name, or description.
Quickly and easily copy insurance, identification, and other wallet‑size cards. You can scan and print both sides of a card on a single page, saving paper and showing the information on the card in a more convenient manner.

1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Apps > Apps Management > Card Copy.
– When scanning a card, make sure the scan resolution is not more than 200 dpi for color, and 400 dpi for
black and white. – When scanning multiple cards, make sure the scan resolution is not more than 150 dpi for color, and
300 dpi for black and white. • Print Borders—Select the check box to print the scan image with a border around it.
4 Click Apply.
To use the application, touch Card Copy on the scanner home screen, and then follow the instructions.
Use To

Setting up and using the home screen applications 23

Create shortcuts on the scanner home screen, with settings for up to 25 frequently used copy, fax, or e-mail jobs.
To use the application, touch MyShortcut, and then follow the instructions on the scanner display.

Scan a document, and then send the scanned document to multiple destinations.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Apps > Apps Management > Multi Send.
3 From the Profiles section, click Add, and then customize the settings.
4 Click Apply.
To use the application, touch Multi Send on the scanner home screen, and then follow the instructions on the scanner display.
Use To · Use To

Setting up and using the home screen applications 24

Scan a document and send it to a shared network folder. You can define up to 30 unique folder destinations.
1 Open a Web browser, and then type the scanner IP address in the address field.
3 Specify the destinations, and then customize the settings.
4 If necessary, click Click here to expand for more options.
5 Click OK > Apply.
To use the application, touch Scan to Network on the scanner home screen, and then follow the instructions on the scanner display.

Quickly and easily copy insurance, identification, and other wallet‑size cards using the Automatic Document Feeder (ADF). You can scan and print both sides of a card on a single page, saving paper and showing the information on the card in a more convenient manner.
Use To · Use To

Setting up and using the home screen applications 25
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Apps > Apps Management > ADF Card Copy.
3 Change the default output options, if necessary.
Configuring e‑mail setting
– When scanning a card, make sure the scan resolution is not more than 200 dpi for color, and 400 dpi for
black and white. – When scanning multiple cards, make sure the scan resolution is not more than 150 dpi for color, and 300
dpi for black and white. • Print Borders—Select the check box to print the scan image with a border around it.
5 Click Apply.
To use the application, touch ADF Card Copy on the scanner home screen, and then follow the instructions.

Setting up and using the home screen applications 26

1 Open a Web browser, and then type the scanner IP address in the address field.
2 Add or edit a profile.
From the Configure page, click Add.
From the Configure page, select a profile to edit, and then click Edit.
3 Configure the proxy settings for the scanner. Type the proxy host name and port number used to connect to the server.
4 If necessary, change the Sharepoint settings. For more information, see the documentation that came with your application.
5 Click Apply.
To use the application, touch Scan to Sharepoint on the scanner home screen, and then follow the instructions on the scanner display.
Use To

Setting up and using the home screen applications 27

Create and manage bar code templates to specify the location and type of bar code that users will frequently scan.

To use the application, touch Bar Code Discovery from the scanner home screen, and then follow the instructions on the scanner display.
You can export configuration settings into a text file, and then import the file to apply the settings to other devices.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 To export or import a configuration for one application, do the following: a Click Settings > Apps > Apps Management. b From the list of installed applications, click the name of the application you want to configure.
c Click Configure, and then do either of the following:
– When saving the configuration file, you can type a unique file name or use the default name. – If a "JVM Out of Memory” error occurs, then repeat the export process until the configuration file is
saved. • To import a configuration from a file, click Import, and then browse to the saved configuration file that was exported from a previously configured device.
– Before importing the configuration file, you can choose to preview it first or load it directly. – If a timeout occurs and a blank screen appears, then refresh the Web browser, and then click Apply.
Use To · or

Setting up and using the home screen applications 28
3 To export or import a configuration for multiple applications, do the following: a Click Settings > Import/Export. b Do either of the following:
This application shows the scanner control panel on your computer screen and lets you interact with the scanner control panel, even when you are not physically near the network scanner. From your computer screen, you can view the scanner status, release held print jobs, create bookmarks, and do other print-related tasks you might normally do while standing at the network scanner.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Remote Operator Panel Settings.
3 Select the Enabled check box, and then customize the settings.
4 Click Submit.
To use the application, click Remote Operator Panel > Launch VNC Applet.

Additional scanner and printer setup 29
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the scanner, then turn the scanner off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the scanner, then turn them off as well, and unplug any cables going into the scanner.
Before connecting the scanner and the printer, make sure to:
Communication between the scanner and the printer is disconnected when any of the devices is turned off or when the green Ethernet cable that connects both devices is unplugged. To restore communication between the scanner and the printer:
1 Turn on the printer.
2 Turn on the scanner.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.

Additional scanner and printer setup 30
1 Remove the controller board access cover.


2 Using a flat‑head screwdriver, loosen the screws on the controller board shield.



Additional scanner and printer setup 31
3 Remove the shield.

4 Unpack the scanner communications card, and then locate the connector for the scanner communications card.

1 Scanner communications card connector
2 Memory card connector

Additional scanner and printer setup 32
5 Holding the card by its sides, align the plastic pins (1) on the card with the holes (2) on the controller board, and then push the card firmly into place.

6 Align the screws with the holes on the shield, and then reattach the shield.


Additional scanner and printer setup 33
7 Tighten the screws on the shield.
8 Reattach the access cover.



Additional scanner and printer setup 34
You can customize your scanner connectivity and memory capacity by adding internal options.
When the printer is connected to the scanner, only the internal options in the scanner function.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the scanner, then turn the scanner off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the scanner, then turn them off as well, and unplug any cables going into the scanner.
1 Move the scan bar to its home position.
a From the home screen, touch
> Lock Scanner Head. b Turn off the scanner and printer.
c Lock the scan bar.



Additional scanner and printer setup 35
2 Tape the scanner cover to secure it in place.

3 Remove the exit tray.

4 Turn the scanner upside down on a flat surface.

5 Remove all screws from the system board cover.


Additional scanner and printer setup 36
6 Remove the system board cover.

7 Locate the appropriate connector.

1 Firmware and flash memory card connectors
2 Lexmark Internal Solutions Port or scanner hard disk connector
3 Scanner hard disk*
4 Memory card connector
* The scanner is shipped with one hard disk and one fax modem installed on the system board.
5 Fax modem*

Additional scanner and printer setup 37
8 Reattach the system board cover.
9 Attach all the screws to secure the system board cover.
10 While holding the scanner cover, turn the scanner right side up.

11 Reattach the exit tray. a Attach the tray at the rear hinge.


Additional scanner and printer setup 38
b Push down the tray to secure it on the front hinge.

c Return the tray to its original position.

The system board supports one optional Lexmark Internal Solutions Port (ISP). Install an ISP for additional connectivity options.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the scanner, then turn the scanner off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the scanner, then turn them off as well, and unplug any cables going into the scanner.

Additional scanner and printer setup 39
1 Unpack the ISP kit.

2 Plastic mounting bracket
2 Access the system board. For more information, see “Accessing the system board” on page 34.
3 Remove the scanner hard disk.

3 Thumbscrews

Additional scanner and printer setup 40
b Remove the screws that secure the hard disk in place.

c Remove the hard disk by pulling it upward to unseat the standoffs.

4 Remove the metal cover from the ISP opening.


Additional scanner and printer setup 41
5 Remove the small bracket from the system board cage.



6 Install the ISP in the same location where the hard disk was located on the system board. a Align the posts of the plastic mounting bracket with the holes on the system board cage, and then press the
bracket on the cage until it clicks into place. b Install the ISP on the bracket.
c Use the provided thumbscrew for the ISP to attach the bracket to the ISP.


Additional scanner and printer setup 42


7 Insert the plug of the ISP interface cable into the connector of the system board.

8 Remove the thumbscrews that attach the hard disk mounting bracket to the hard disk, and then remove the bracket.


Additional scanner and printer setup 43
9 Attach the small bracket to the hard disk.

10 Align the standoffs of the hard disk with the holes on the ISP, and then press down the hard disk until the standoffs click into place.


Additional scanner and printer setup 44
11 Insert the plug of the hard disk interface cable into the connector on the ISP.
12 Secure the hard disk to the system board cage.


Additional scanner and printer setup 45
13 Secure the ISP to the cage using the screws that came with the ISP kit.

14 Reattach the system board cover.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the scanner, then turn the scanner off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the scanner, then turn them off as well, and unplug any cables going into the scanner.

Additional scanner and printer setup 46
1 Access the scanner system board.
For more information, see “Accessing the system board” on page 34.
2 Squeeze the clips, and then lift the bracket to remove the scanner communications card.

3 Unpack the optional card.
4 Holding the card by its sides, align the plastic pins (1) on the card with the holes (2) on the system board.


Additional scanner and printer setup 47
5 Push the card firmly into place as shown in the illustration.

6 Reattach the system board shield.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the scanner, then turn the scanner off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the scanner, then turn them off as well, and unplug any cables going into the scanner.
An optional memory card can be purchased separately and attached to the system board.
1 Access the system board.
For more information, see “Accessing the system board” on page 34.
2 Unpack the memory card.

Additional scanner and printer setup 48
3 On the system board, open the memory card connector latches.

4 Align the notches on the memory card to the ridges on the connector.

1 Notch · 2 Ridge

Additional scanner and printer setup 49
5 Push the memory card straight into the connector until it clicks into place.

6 Reattach the system board cover.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Install the printer and any hardware options you have purchased in the following order:

Additional scanner and printer setup 50
For more information on installing a caster base, optional 550‑ or 250‑sheet tray, spacer, or 2100‑sheet tray, see the setup sheet that came with the option.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer using the power switch, and then unplug the power cord from the electrical outlet.


2 Unpack the optional tray, and then remove all packing material.
3 Pull out the tray completely from the base.


4 Remove any packing material from inside the tray.
5 Insert the tray into the base.
6 Place the tray near the printer.
7 Align the optional tray with the caster base.

Additional scanner and printer setup 51

8 Align the printer with the tray, and then slowly lower the printer into place.

Additional scanner and printer setup 52

9 Connect the power cord to the printer, then to a properly grounded electrical outlet, and then turn on the printer.

Additional scanner and printer setup 53



To uninstall the optional trays, slide the latch on the right side of the printer toward the front of the printer until it clicks into place, and then remove stacked trays one at a time from the top to the bottom.
Connect the scanner to the computer using a USB cable or to the network using an Ethernet cable.
Make sure to match the following:

Additional scanner and printer setup 54


1 Ethernet port Connect the printer to the scanner.
Make sure to connect the scanner to the printer using the green Ethernet cable.


1 USB ports Attach an optional wireless network adapter, or connect the scanner to a computer.
2 Ethernet port Connect the scanner to a network.
3 Ethernet port Connect the scanner to the printer.
Use the To · Use the To

Additional scanner and printer setup 55
Attach the Ethernet cable and power cord, and then neatly tuck the cables in the channels at the back of the printer.


1 Obtain a copy of the software installer package.
2 Run the installer, and then follow the instructions on the computer screen.

Additional scanner and printer setup 56
3 For Macintosh users, add the scanner: a From System Preferences in the Apple menu, navigate to the list of scanners, and then select + > IP. b Type the scanner IP address in the address field.
1 Open the printers folder, and then select your printer.
2 Open the printer properties, and then add or manually install any options.
3 Apply the changes.
1 From System Preferences in the Apple menu, navigate to your printer, and then select Options & Supplies > Driver.
2 Add any installed hardware options.
3 Apply the changes.
To configure your scanner to connect to an Ethernet network, organize the following information before you begin:
You will need an Ethernet cable to connect the scanner to the network and an available port where the scanner can physically connect to the network. Use a new network cable when possible to avoid potential problems caused by a damaged cable.

Additional scanner and printer setup 57
Make sure you have the following information before setting up the scanner on a wireless network:
Some ad hoc networks will also require the automatic setting. Check with your system support person if you are not sure which channel to select. • Security Method—There are four basic options for Security Method: – WEP key
If your network uses more than one WEP key, then enter up to four in the provided spaces. Select the key currently in use on the network by selecting the default WEP transmit key. – WPA or WPA2 preshared key or passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the scanner, or the scanner will not be able to communicate on the network. – 802.1X–RADIUS
If you are installing the scanner on an 802.1X network, then you may need the following:
If your wireless network does not use any type of security, then you will not have any security information.
– If you do not know the SSID of the network that your computer is connected to, then launch the wireless utility
of the computer network adapter, and then look for the network name. If you cannot find the SSID or the security information for your network, then see the documentation that came with the access point or contact your system support person. – To find the WPA/WPA2 preshared key or passphrase for the wireless network, see the documentation that
came with the access point, see the Embedded Web Server associated with the access point, or consult your system support person.

Additional scanner and printer setup 58
Before you begin, make sure that:
> Network/Ports > Active NIC > Auto > Submit
1 From the scanner control panel, navigate to:
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wireless Connection Setup
2 Select a wireless connection setup.
Search for networks Show available wireless connections.
Enter a network name Manually type the SSID.
Wi‑Fi Protected Setup Connect the scanner to a wireless network using Wi‑Fi Protected Setup.
3 Follow the instructions on the scanner display.
Connecting the scanner to a wireless network using Wi‑Fi Protected Setup
Before you begin, make sure that:
1 From the scanner control panel, navigate to:
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wireless Connection Setup > Wi‑Fi Protected Setup > Start Push Button Method
2 Follow the instructions on the scanner display.
1 From the scanner control panel, navigate to:
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wireless Connection Setup > Wi‑Fi Protected Setup > Start PIN Method
2 Copy the eight‑digit WPS PIN.
Use To

Additional scanner and printer setup 59
3 Open a Web browser, and then type the IP address of your access point in the address field.
4 Access the WPS settings. For more information, see the documentation that came with your access point.
5 Enter the eight‑digit PIN, and then save the setting.
Before you begin, make sure that:
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Network/Ports > Wireless.
3 Modify the settings to match the settings of your access point (wireless router).
4 Click Submit.
5 Turn off the scanner, and then disconnect the Ethernet cable. Wait for at least five seconds, and then turn on the scanner.
6 To verify if your scanner is connected to the network, print a network setup page. In the Network Card [x] section, see if the status is Connected.
1 Open the printers folder.
2 From the shortcut menu of the printer with the new ISP, open the printer properties.

Additional scanner and printer setup 60
3 Configure the port from the list.
4 Update the IP address.
5 Apply the changes.
1 From System Preferences in the Apple menu, navigate to the list of printers, and then select + > IP.
2 Type the IP address in the address field.
3 Apply the changes.
Use serial printing when the computer is far from the printer. After installing the serial or communication (COM) port, configure the printer and the computer.
1 Set the parameters in the printer. a From the control panel, navigate to the menu for the port settings. b Locate the menu for the serial port settings, and then adjust the settings, if necessary.
c Save the settings.
2 From your computer, open the printers folder, and then select your printer.
3 Open the printer properties, and then select the COM port from the list.
4 Set the COM port parameters in Device Manager.
Use the Run dialog box to open the command prompt, and then type devmgmt.msc.
When all hardware and software options are installed and the printer is turned on, verify that the printer is set up correctly by printing the following:
From the home screen, navigate to:
> Reports > Menu Settings Page

Additional scanner and printer setup 61
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the home screen, navigate to:
> Reports > Network Setup Page
2 Check the first section of the network setup page, and confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult a system support person for a solution, and then print another network setup page.

Loading paper and specialty media 62
Setting the paper size and type
From the home screen navigate to:
> Paper Menu > Paper Size/Type > select a tray > select the paper size or type > Submit
Universal paper size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus.
1 From the home screen, navigate to:
> Paper Menu > Universal Setup > Units of Measure > select a unit of measure
2 Touch Portrait Width or Portrait Height.
3 Select the width or height, and then touch Submit.
1 Pull out the tray.

Loading paper and specialty media 63

2 Squeeze, and then slide the width guide to the correct position for the size of the paper being loaded until it clicks into place.



Loading paper and specialty media 64

3 Unlock the length guide, then squeeze, and then slide the guide to the correct position for the size of the paper being loaded.


Loading paper and specialty media 65

4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper stack with the printable side facedown.

Without an optional staple finisher With an optional staple finisher

Loading paper and specialty media 66

Without an optional staple finisher With an optional staple finisher



Loading paper and specialty media 67



Loading paper and specialty media 68

6 For custom‑ or Universal‑size paper, adjust the paper guides to lightly touch the sides of the stack, and then lock the length guide.
7 Insert the tray.

8 From the scanner control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.

Loading paper and specialty media 69
1 Pull out the tray.
2 Adjust the width and length guides.
Loading A5‑size paper
a Pull up and slide the width guide to the position for A5.



Loading paper and specialty media 70
b Squeeze and slide the length guide to the position for A5 until it clicks into place.

c Remove the A5 length guide from its holder.


d Insert the A5 length guide into its designated slot.

Loading paper and specialty media 71


Loading A4‑, letter‑, legal‑, oficio‑, and folio‑size paper
a Pull up and slide the width guide to the correct position for the size of the paper being loaded.


Loading paper and specialty media 72
b If the A5 length guide is still attached to the length guide, then remove it from its place. If the A5 length guide
is not attached, then proceed to step d.

c Put the A5 length guide in its holder.

Loading paper and specialty media 73
d Squeeze the length guide and slide it to the correct position for the size of the paper being loaded until it clicks
into place.

3 Flex the sheets back and forth to loosen them. Do not fold or crease the paper. Straighten the edges on a level surface.

4 Load the paper stack with the printable side facedown.

Loading paper and specialty media 74

Without an optional staple finisher With an optional staple finisher

Loading paper and specialty media 75


5 Insert the tray.

Loading paper and specialty media 76

6 From the scanner control panel, set the size and type in the Paper menu to match the paper loaded in the tray.
1 Pull down the multipurpose feeder door.

B5
EXEC
A4 A5

Loading paper and specialty media 77
2 Pull the multipurpose feeder extender.

LTR
B5
EXEC
3 Slide the width guide to the correct position for the size of the paper being loaded.

A4 A5
EXEC
B5

Loading paper and specialty media 78

B5
4 Prepare the paper or specialty media for loading. • Flex sheets of paper back and forth to loosen them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper or specialty media.

Loading paper and specialty media 79
Without an optional staple finisher With an optional staple finisher

ABC
One‑sided printing
One‑sided printing

Two‑sided (duplex) printing
Two‑sided (duplex) printing

LTR
B5
EXEC

Loading paper and specialty media 80


6 For custom- or universal-size paper, adjust the width guides to lightly touch the sides of the stack.
7 From the scanner control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
1 Move the ADF guides to the A8 paper size position.


Loading paper and specialty media 81
2 Load the business cards facedown, short‑edge first into the ADF.

When the paper size and paper type for any trays are the same, the printer links those trays. When one linked tray becomes empty, paper feeds from the next linked tray. We recommend giving all unique paper, such as letterhead and different colored plain papers, a different custom type name so that the trays they are in do not automatically link.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Paper Menu.
4 Click Submit.

Loading paper and specialty media 82
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Select a custom name, and then type a custom paper type name.
4 Click Submit.
5 Click Custom Types, and then verify if the new custom paper type name has replaced the custom name.
1 From the scanner home screen, navigate to:
> Paper Menu > Custom Names
2 Select a custom name, and then type a custom paper type name.
3 Touch Submit.
4 Touch Custom Types, and then verify if the new custom paper type name has replaced the custom name.
Assign a custom paper type name to a tray when linking or unlinking trays.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Type a name for the paper type, and then click Submit.
4 Select a custom type, and then verify that the correct paper type is associated with the custom name.

Paper and specialty media guide 83
Using specialty media
Card stock is a heavy, single‑ply specialty paper. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly affect print quality.

Paper and specialty media guide 84
Source Printing Printable side Paper orientation
Trays One‑sided Facedown Load the sheet with the top edge toward the front of the tray.
Trays Two‑sided Faceup Load the sheet with the bottom edge entering the printer first.
Multipurpose feeder One‑sided Faceup Load the sheet with the top edge entering the printer first.
Multipurpose feeder Two‑sided Facedown Load the sheet with the bottom edge entering the printer first.

Paper and specialty media guide 85
The following paper characteristics affect print quality and reliability. Consider these factors before printing on them:
The printer trays and multipurpose feeder can automatically feed paper weights between 60–176 g/m2 (16–47‑lb) grain long paper. The 2100‑sheet tray can automatically feed paper weights up to 60–135 g/m2 (16–36‑lb) grain long paper. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, and may cause jams.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.
Paper smoothness directly affects print quality. If paper is too rough, toner cannot fuse to it properly. If paper is too smooth, it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; smoothness between 150 and 250 Sheffield points produces the best print quality.
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.
Store paper in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extend the time several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60–176 g/m2 (16–47‑lb) paper, grain long paper is recommended.
Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability, resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton can negatively affect paper handling.
Using the appropriate paper prevents jams and helps ensure trouble‑free printing.

Paper and specialty media guide 86
To help avoid paper jams and poor print quality:
As an environmentally conscientious company, Lexmark supports the use of recycled paper produced specifically for use in laser (electrophotographic) printers.
While no blanket statement can be made that all recycled paper will feed well, Lexmark consistently tests papers that represent recycled cut size copier papers available on the global market. This scientific testing is conducted with rigor and discipline. Many factors are taken into consideration both separately and as a whole, including the following:
Recycled papers are better than ever; however, the amount of recycled content in a paper affects the degree of control over foreign matter. And while recycled papers are one good path to printing in an environmentally responsible manner, they are not perfect. The energy required to de-ink and deal with additives such as colorants and “glue” often generates more carbon emissions than does normal paper production. However, using recycled papers enables better resource management overall.
Lexmark concerns itself with the responsible use of paper in general based on life cycle assessments of its products. To gain a better understanding of the impact of printers on the environment, the company commissioned a number of life cycle assessments and found that paper was identified as the primary contributor (up to 80%) of carbon emissions

Paper and specialty media guide 87
caused throughout the entire life of a device (from design to end-of-life). This is due to the energy-intensive manufacturing processes required to make paper.
Thus, Lexmark seeks to educate customers and partners on minimizing the impact of paper. Using recycled paper is one way. Eliminating excessive and unnecessary paper consumption is another. Lexmark is well-equipped to help customers minimize printing and copying waste. In addition, the company encourages purchasing paper from suppliers who demonstrate their commitment to sustainable forestry practices.
Lexmark does not endorse specific suppliers, although a converter’s product list for special applications is maintained. However, the following paper choice guidelines will help alleviate the environmental impact of printing:
1 Minimize paper consumption.
2 Be selective about the origin of wood fiber. Buy from suppliers who carry certifications such as the Forestry Stewardship Council (FSC) or The Program for the Endorsement of Forest Certification (PEFC). These certifications guarantee that the paper manufacturer uses wood pulp from forestry operators that employ environmentally and socially responsible forest management and restoration practices.
3 Choose the most appropriate paper for printing needs: normal 75 or 80 g/m2 certified paper, lower weight paper, or recycled paper.
Test results indicate that the following paper types are at risk for use with laser printers:
For more information about Lexmark, visit www.lexmark.com. General sustainability-related information can be found at the Environmental Sustainability link.
Use these paper storage guidelines to help avoid jams and uneven print quality:

Paper and specialty media guide 88
The following tables provide information on standard and optional paper input sources and the sizes, types, and weights of paper they support..

Paper size ADF ADF - Automatic ADF - Mixed sizes Scanner glass
Executive 184 x 267 mm (7.3 x 10.5 in.)
1 Paper size is supported if printer is set to Metric.
2 Paper size is supported if printer is set to US.

Paper and specialty media guide 89

Paper size ADF ADF - Automatic ADF - Mixed sizes Scanner glass
138 x 210 mm (5.5 x 8.3 in.) up to 216 x 356 mm (8.5 x 14 in.)
1 Paper size is supported if printer is set to Metric.
2 Paper size is supported if printer is set to US.
Paper size1 Dimensions Standard or optional 250‑ or 550‑sheet tray
Optional 2100‑sheet tray Multipurpose feeder
A4 210 x 297 mm (8.3 x 11.7 in.)
A5 148 x 210 mm (5.8 x 8.3 in.)
A6 105 x 148 mm (4.1 x 5.8 in.)
JIS B5 182 x 257 mm (7.2 x 10.1 in.)
Letter 216 x 279 mm (8.5 x 11 in.)
Legal 216 x 356 mm (8.5 x 14 in.)
Executive 184 x 267 mm (7.3 x 10.5 in.)
Oficio 216 x 340 mm (8.5 x 13.4 in.)
Folio 216 x 330 mm (8.5 x 13 in.)
Statement 140 x 216 mm (5.5 x 8.5 in.)
1 If your preferred default paper size cannot be set in the scanner control panel, then you may select common paper sizes that correspond to the position of the length guide in the tray from the Paper Size/Type menu. If the paper size is not available, then select Universal or turn off tray size sensing. For more information, contact customer support.
2 Universal is supported in duplex mode only if the width is from 105 mm (4.13 in.) to 216 mm (8.5 in.), and the length is from 148 mm (5.83 in.) to 356 mm (14 in.)
3 When printing on paper less than 210 mm (8.3 in.) wide, the printer prints at a reduced speed to prevent damage to the fuser.
4 This paper size is supported only in select printer models.
Duplex

Paper and specialty media guide 90
Paper size1 Dimensions Standard or optional 250‑ or 550‑sheet tray
Optional 2100‑sheet tray Multipurpose feeder
Universal2,3 105 x 148 mm to 216 x 356 mm (4.13 x 5.83 in. to 8.5 x 14 in.)
70 x 127 mm to 216 x 356 mm (2.76 x 5 to 8.5 x 14 in.)
7 3/4 Envelope (Monarch)4
98 x 191 mm (3.9 x 7.5 in.)
9 Envelope4 98 x 225 mm (3.9 x 8.9 in.)
10 Envelope4 105 x 241 mm (4.1 x 9.5 in.)
DL Envelope4 110 x 220 mm (4.3 x 8.7 in.)
C5 Envelope4 162 x 229 mm (6.38 x 9.01 in.)
B5 Envelope4 176 x 250 mm (6.93 x 9.84 in.)
Other Envelope4 98 x 162 mm (3.9 x 6.4 in.) to 176 x 250 mm (6.9 x 9.8 in.)
1 If your preferred default paper size cannot be set in the scanner control panel, then you may select common paper sizes that correspond to the position of the length guide in the tray from the Paper Size/Type menu. If the paper size is not available, then select Universal or turn off tray size sensing. For more information, contact customer support.
2 Universal is supported in duplex mode only if the width is from 105 mm (4.13 in.) to 216 mm (8.5 in.), and the length is from 148 mm (5.83 in.) to 356 mm (14 in.)
3 When printing on paper less than 210 mm (8.3 in.) wide, the printer prints at a reduced speed to prevent damage to the fuser.
4 This paper size is supported only in select printer models.
Duplex

Paper and specialty media guide 91

Paper size 4‑bin mailbox Output expander and
1 The finisher stacks the paper but does not staple or punch holes in it.
2 The finisher staples the paper if it is loaded long edge first.
3 The finisher staples the paper if its width is between 8.27 and 8.54 inches but does not punch holes in it.
4 This paper size is supported only in select printer models.
The printer engine supports 60–176‑g/m2 (16–47‑lb) paper weights.

Paper type 250‑ or 550‑sheet trays
1 This paper type is supported only in select printer models.
2 Print on transparencies by batches of only up to 20 to prevent them from sticking together. For more information, see “Tips on using transparencies” on page 84.

Paper and specialty media guide 92

Paper type 250‑ or 550‑sheet trays
1 This paper type is supported only in select printer models.
2 Print on transparencies by batches of only up to 20 to prevent them from sticking together. For more information, see “Tips on using transparencies” on page 84.

Paper type Paper weight 4‑bin mailbox Output expander and high‑capacity
1 The finisher stacks the paper but does not staple or punch holes in it.
2 Print on transparencies by batches of only up to 20 to prevent them from sticking together. For more information, see “Tips on using transparencies” on page 84.
3 This paper type is supported only in select printer models.

Paper and specialty media guide 93

Paper type Paper weight 4‑bin mailbox Output expander and high‑capacity
1 The finisher stacks the paper but does not staple or punch holes in it.
2 Print on transparencies by batches of only up to 20 to prevent them from sticking together. For more information, see “Tips on using transparencies” on page 84.
3 This paper type is supported only in select printer models.

Printing forms and documents
Use the Forms and Favorites application to quickly and easily access frequently used forms or other information that is regularly printed. Before you can use this application, first set it up on the scanner. For more information, see “Setting up Forms and Favorites” on page 21.
1 From the scanner home screen, navigate to:
Forms and Favorites > select the form from the list > enter the number of copies > adjust other settings
1 From the scanner control panel Paper menu, set Paper Type and Paper Size to match the loaded paper.
2 Send the print job:
a With a document open, click File > Print. b Click Properties, Preferences, Options, or Setup.
c Adjust settings as needed. d Click OK > Print.
a Customize the settings as needed in the Page Setup dialog:
1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the loaded paper. 3 Click OK. b Customize the settings as needed in the Print dialog:
1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options. 2 From the Print dialog and pop‑up menus, adjust the settings as needed.
1 Open a Web browser, and then type the scanner IP address in the address field.
Printing 94 · 2 Touch

2 Click Settings > Print Settings > Quality Menu.
3 Adjust the toner darkness setting, and then click Submit.
1 From the scanner home screen, navigate to:
> Settings > Print Settings > Quality Menu
2 Adjust the toner darkness setting, and then touch Submit.
1 Insert a flash drive into the scanner USB port.

Printing 95

2 From the scanner control panel, touch the document you want to print.
3 Touch the arrows to get a preview of the document.
to specify the number of copies to print, and then touch Print.
Printing 96 · 4 Use · or

Recommended flash drives File type
Documents:
Images:
To download a compatible mobile printing application, visit www.lexmark.com/mobile.
1 From the scanner control panel, navigate to:
> Security > Confidential Print > select the print job type
Max Invalid PIN Limit the number of times an invalid PIN can be entered.
Confidential Job Expiration Hold print jobs in the computer until you enter the PIN from the scanner control panel.
Repeat Job Expiration Print and store print jobs in the scanner memory.
Verify Job Expiration Print one copy of a print job and hold the remaining copies. It allows you to examine if the first copy is satisfactory. The print job is automatically deleted from the scanner memory when all copies are printed.
Reserve Job Expiration Store print jobs for printing at a later time.
Printing 97 · Use To

2 Touch Submit.
1 With a document open, click File > Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click Print and Hold.
4 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
5 Click OK or Print.
1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2 From the print options or Copies & Pages pop‑up menu, choose Job Routing.
3 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
4 Click OK or Print.
Printing 98 · Use To

1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Security > Confidential Print Setup.
4 Click Submit to save the modified settings.
1 From the home screen, navigate to:
> Reports > Print Fonts
2 Touch PCL Fonts or PostScript Fonts.
A directory list shows the resources stored in a flash memory or on the scanner hard disk.
From the scanner home screen, navigate to:
> Reports > Print Directory
1 From the scanner control panel, touch Cancel Jobs or press
on the keypad.
2 Touch the print job you want to cancel, and then touch Delete Selected Jobs.
on the keypad, then touch Resume to return to the home screen.
Printing 99

1 Open the printers folder, and then select your printer.
2 From the print queue, select the print job you want to cancel, and then delete it.
1 From System Preferences in the Apple menu, navigate to your printer.
2 From the print queue, select the print job you want to cancel, and then delete it.
Printing 100

Automatic document feeder (ADF) Scanner glass
Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the scanner control panel, touch Copy It.
1 Load an original document facedown into the ADF.
2 Adjust the paper guides.
3 From the home screen, navigate to:
Copy > change the copy settings > Copy It
Copying 101

1 Place an original document facedown on the scanner glass in the lower left corner.
2 From the home screen, navigate to:
Copy > specify the copy settings > Copy It
3 If you have more pages to scan, then place the next document on the scanner glass, and then touch Scan the Next Page.
4 Touch Finish the Job to return to the home screen.
1 Place a photo facedown on the lower left corner of the scanner glass.
2 From the home screen, navigate to:
Copy > Content > Photo >
3 Touch Scan the Next Page or Finish the Job.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Copy from > select the size of the original document >
4 Touch Copy to, and then select the tray that contains transparencies, or touch Manual Feeder Size.
5 Load transparencies in the multipurpose feeder.
6 From the home screen, navigate to:
> select the size of the transparencies loaded > Manual Feeder Type >

1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Copy from > specify the size of the original document > Copy to > Manual Feeder
4 If you are printing on one side of the letterhead and using a finisher, then place the letterhead faceup, top edge first in the multipurpose feeder.
5 Select the size of the letterxhead.
6 Navigate to:
Continue > Letterhead > Continue > Copy It
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Copy from > select the size of the original document >
5 Touch Copy to > select the size of the copy >
6 Touch Copy It.
1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
Copying 103

3 From the home screen, navigate to:
Copy > Copy from > select the size of the original document >
4 Navigate to:
Copy to > select the tray containing the paper type you want to use >
5 Touch Copy It.
Use the ADF to copy original documents with different paper sizes. Depending on the paper sizes loaded and the “Copy to” and “Copy from” settings, each copy is either printed on mixed paper sizes (Example 1) or scaled to fit a single paper size (Example 2).
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Copy from > Mixed Sizes >
> Copy to > Auto Size Match >
The scanner identifies the different paper sizes as they are scanned. Copies are printed on mixed paper sizes corresponding to the paper sizes of the original document.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Copy from > Mixed Sizes >
> Copy to > Letter >
The scanner identifies the different paper sizes as they are scanned, and then scales the mixed paper sizes to fit on the paper size selected.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
Copying 104 · > Copy It · > Copy It

4 From the Sides (Duplex) area, touch the button for your preferred duplexing method.
The first number represents sides of the original documents; the second number represents sides of the copy. For example, select 1‑sided to 2‑sided if you have 1-sided original documents and you want 2‑sided copies.
, and then Copy It.
Copies can be scaled from 25% to 400% of the original document size.
1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, touch Copy.
4 From the Scale area, touch
to decrease or increase the value by 1%.
Touching “Copy to” or “Copy from” after manually setting Scale changes the scale value back to Auto.
5 Touch Copy It.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:

> Copy It.
If you print multiple copies of a document, then you can choose to print the copies as a set (collated) or to print the copies as groups of pages (not collated).
1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > enter the number of copies > Collate > select the preferred order of pages >
1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.

3 From the home screen, navigate to:
Copy > Advanced Options > Separator Sheets
> Copy It.
To save paper, you can copy either two or four consecutive pages of a multiple‑page document onto a single sheet of paper.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Advanced Options > Paper Saver > select output >
The custom copy job or job build is used to combine one or more sets of original documents into a single copy job. Each set may be scanned using different job parameters. When a copy job is submitted and Custom Job is enabled, the scanner scans the first set of original documents using the specified settings, and then it scans the next set with the same or different settings.
The definition of a set depends on the scan source:
For example:
1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
Copying 107 · 5 Touch · > Copy It

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Advanced Options > Custom Job > On >
4 Load the next document facedown, long edge first into the ADF tray or facedown on the scanner glass, and then touch Scan from automatic feeder or Scan from flatbed.
5 If you have another document to scan, then repeat the previous step. Otherwise, touch Finish the job.
1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Advanced Options > Header/Footer > select where you want to place the header or footer > select the type of header or footer you want
4 Enter the required information depending on the header or footer you selected, and then touch Done.
, and then press .
An overlay message can be placed on each page. The message choices are Urgent, Confidential, Copy, Custom, and Draft.
1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
Copying 108 · > Copy It · 5 Touch

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Advanced Options > Overlay > select overlay message > Done > Copy It
When the ADF begins processing a document, touch Cancel Job on the scanner control panel.
From the home screen, touch Cancel Job.
Canceling appears on the display. When the job is canceled, the Copy screen appears.
1 From the scanner control panel, touch Cancel Job or press
on the keypad.
2 Touch the job you want to cancel, and then touch Delete Selected Jobs.
on the keypad, then touch Resume to return to the home screen.
This option opens a screen where you can select the paper size of the original document.
This option opens a screen where you can enter the paper size and type on which your copies will be printed.
Copying 109

This option lets you scale the document from 25% to 400% of the original document size. You can also set automatic scaling.
on the scanner control panel. To make a continuous decrease or increase in value, hold the button for two seconds or more.
This option lets you adjust how light or dark the copies are in relation to the original document.
This option lets you make one- or two-sided copies from one- or two-sided original documents.
This option keeps the pages of a print job stacked in sequence when printing multiple copies of the document.
This option lets you set the number of copies to be printed.
This option lets you set the original document type and source.
Select from the following content types:
Select from the following content sources:
Copying 110 · or

This option lets you save the current settings by assigning a shortcut name.
Select from the following settings:
Copying 111 · or

Automatic document feeder (ADF) Scanner glass
Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > E-mail/FTP Settings > E-mail Settings.
3 Enter the appropriate information, and then click Submit.
1 Type the scanner IP address or host name in the address field of your Web browser.
If you do not know the IP address or host name of the scanner, then you can:
2 Click Settings > E-mail/FTP Settings > E-mail Settings.
E-mailing 112

3 Fill in the fields with the appropriate information.
4 Click Submit.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings.
3 From the Other Settings column, click Manage Shortcuts > E-mail Shortcut Setup.
4 Type a unique name for the e‑mail recipient, and then type the e‑mail address. If you are entering multiple addresses, then separate each address with a comma.
5 Click Add.
1 From the home screen, navigate to:
E-mail > Recipient > type an e‑mail address
To create a group of recipients, touch Next address, and then type the next recipient’s e-mail address.
2 Touch Subject, then type the e‑mail subject, and then touch Done.
3 Touch Message, then type your message, and then touch Done.
4 Adjust the e‑mail settings.
6 Type a unique name for the shortcut, and then touch Done.
7 Verify that the shortcut name is correct, and then touch OK.
If the shortcut name is incorrect, then touch Cancel, and then reenter the information.
E-mailing 113 · 5 Touch

You can use the printer to e‑mail scanned documents to one or more recipients in a number of ways. You can type the e‑mail address, use a shortcut number, or use the address book. You can also use the Multi Send or MyShortcut application from the scanner home screen. For more information, see “Activating the home screen applications” on page 21.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
4 Enter the e‑mail address, or press
and then enter the shortcut number.
To enter additional recipients, touch Next Address, and then enter the address or shortcut number you want to add.
5 Touch Done > Send It.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
, enter the shortcut number using the keypad, and then touch
To enter additional recipients, touch Next address, and then enter the address or shortcut number you want to add.
4 Touch Send It.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
E-mail > Recipient(s) >
> enter the name of recipient > Search
E-mailing 114 · E-mail > Recipient · 3 Press

4 Touch the name of the recipients.
To enter additional recipients, touch Next address, and then enter the address or shortcut number you want to add, or search the address book.
5 Touch Done.
1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
E-mail > Recipient(s) > type the e‑mail address > Done
4 Touch Subject, then type the e‑mail subject, and then touch Done.
5 Touch Message, then type your message, and then touch Done.
1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
E-mail > Recipient(s) > type the e‑mail address > Done > Send as
E-mailing 115

> Send It.
This option lets you enter the recipient of your e-mail. You may enter multiple e‑mail addresses.
This option lets you type a subject line for your e-mail.
This option lets you type a message that will be sent with your scanned attachment.
This option lets you customize the attachment file name.
This option lets you set the paper size of the documents you are going to e‑mail. When Original Size is set to Mixed Sizes, you can scan an original document that contains mixed paper sizes (letter‑ and legal‑size pages).
This option lets you adjust the output quality of your e-mail. Increasing the image resolution increases the e-mail file size and the time needed to scan your original document. Decreasing the image resolution reduces the file size.
E-mailing 116 · 5 Touch

This option lets you set the original document type and source.
Select from the following content types:
Select from the following content sources:
This option lets you save the current settings as a shortcut by assigning a shortcut name.
This option lets you adjust how light or dark your scanned documents are in relation to the original document.
This option lets you set the output type for the scan image.
Select one of the following:
E-mailing 117

This option lets you change the following settings:
This option displays the first page of the image before it is included in the e-mail. When the first page is scanned, the scanning is paused and a preview image appears.
Select from the following settings:
E-mailing 118

Automatic document feeder (ADF) Scanner glass
Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
Faxing 119

Many countries and regions require outgoing faxes to contain the following information in a margin at the top or bottom of each transmitted page, or on the first page of the transmission: station name (identification of the business, other entity, or individual sending the message) and station number (telephone number of the sending fax machine, business, other entity, or individual).
To enter your fax setup information, use the scanner control panel, or use your browser to access the Embedded Web Server, and then enter the Settings menu.
When the scanner is turned on for the first time or if the scanner has been off for an extended time, a series of start‑up screens appear. If the scanner has fax capabilities, then the following screens appear:
Fax Name or Station Name Fax Number or Station Number
1 When Fax Name or Station Name appears, enter the name to be printed on all outgoing faxes.
2 Touch Submit.
3 When Fax Number or Station Number appears, enter the printer fax number.
4 Touch Submit.
1 Type the scanner IP address in the address field of your Web browser.
If you do not know the IP address of the scanner, then you can:
2 Click Settings > Fax Settings > Analog Fax Setup.
3 In the Fax Name or Station Name field, enter the name to be printed on all outgoing faxes.
Faxing 120

4 In the Fax Number or Station Number field, enter the printer fax number.
5 Click Submit.
Setup 1: Scanner is connected to a dedicated fax line


To connect:
1 Connect one end of the telephone cable that came with the scanner to the port of the scanner.
2 Connect the other end of the telephone cable to an active analog wall jack.
Faxing 121

Connected to the same telephone wall jack

To connect:
1 Connect one end of the telephone cable that came with the scanner to the port of the scanner.
2 Connect the other end of the telephone cable to an active analog wall jack.
3 Connect the answering machine to the port of the scanner.
Faxing 122

Connected to different wall jacks

To connect:
1 Connect one end of the telephone cable that came with the scanner to the port of the scanner.
2 Connect the other end of the telephone cable to an active analog wall jack.
Faxing 123


To connect:
1 Connect one end of the telephone cable that came with the scanner to the port of the scanner.
2 Connect the other end of the telephone cable to an active analog wall jack.
3 Connect the telephone to the port of the scanner.
When you answer the telephone and you hear fax tones, press *9* or the manual answer code on the telephone to receive the fax. • You can also set the scanner to receive faxes automatically (Auto Answer On), but you need to turn off the voice mail service when you are expecting a fax. This setting works best if you are using voice mail more often than fax.
Faxing 124



A Digital Subscriber Line splits your regular telephone line into two channels: voice and Internet. Telephone and fax signals travel through the voice channel, and Internet signals pass through the other channel. This way, you can use the same line for analog voice calls (including faxes) and digital Internet access.
To minimize interference between the two channels and ensure a quality connection, you need to install a DSL filter for the analog devices (fax machine, telephone, answering machine) in your network. Interference causes noise and static on the telephone, failed and poor quality faxes for the scanner, and slow Internet connection on your computer.
To install a filter for the scanner:
1 Connect the line port of the DSL filter to the wall jack.
2 Connect one end of the telephone cable that came with your scanner to the port of the scanner. Connect the other end to the phone port on the DSL filter.
3 To continue using a computer for Internet access, connect the computer to the DSL HPN port on the DSL filter.
4 To connect a telephone to the scanner, remove any installed adapter plug from the port of the scanner, and then connect the telephone to the port.
Faxing 125


To connect:
1 Connect one end of the telephone cable that came with the scanner to the port of the scanner.
2 Connect the other end of the cable to the port labeled Phone Line 1 or Phone Port on the VoIP adapter.
3 Connect the telephone to the port of the scanner.
Faxing 126

Setup 1: Scanner is connected directly to a cable modem

1 Connect one end of the telephone cable that came with your scanner to the port of the scanner.
2 Connect the other end of the cable to the port labeled Phone Line 1 or Phone Port on the cable modem.
3 Connect your analog telephone to the port of the scanner.
Faxing 127

Setup 2: Scanner is connected to a wall jack; cable modem is installed elsewhere in the facility

1 Connect one end of the telephone cable that came with your scanner to the port of the scanner.
2 Connect the other end of the telephone cable to an active analog telephone wall jack.
3 Connect your analog telephone to the port of the scanner.
Some countries or regions may have different types of telephone wall jack connectors than those that came with the scanner. The standard wall jack adopted by most countries or regions is RJ-11. Your scanner comes with the RJ-11 jack and a telephone cable with the RJ-11 plug.
If the wall jack or equipment in your facility is not compatible with this type of connection, then you need to use a telephone adapter. An adapter for your country or region may not come with your scanner, and you may need to purchase it separately.
Faxing 128

There may be an adapter plug installed in the port of the scanner. If you are using a telephone adapter or a facility that has a cascaded or serial wiring scheme, then do not remove the adapter plug from the port of the scanner.

Connecting the scanner to a non‑RJ‑11 wall jack

1 Connect one end of the telephone cable that came with scanner to the port of the scanner.
2 Connect the other end of the cable to the RJ‑11 adapter, and then connect the adapter to the wall jack.
Faxing 129

3 If you want to connect another device (telephone or answering machine) to the same wall jack, and if the device has a non‑RJ‑11 connector, then connect it directly to the telephone adapter.
The German wall jack has two kinds of ports. The N ports are for fax machines, modems, and answering machines. The F port is for telephones.
Faxing 130

Connect the scanner to any of the N ports.

1 Connect one end of the telephone cable that came the scanner to the port of the scanner.
2 Connect the other end of the telephone cable to the RJ‑11 adapter, and then connect the adapter to an N port.
3 If you want to connect a telephone and answering machine to the same wall jack, then connect the devices as shown.
Faxing 131

A distinctive ring service may be available from your telephone company. This service lets you have multiple telephone numbers on one telephone line, with each telephone number having a different ring pattern. This may be useful for distinguishing between fax and voice calls. If you subscribe to a distinctive ring service, then follow these steps to connect the equipment:
1 Connect one end of the telephone cable that came with the scanner to the scanner LINE port .
2 Connect the other end of the telephone cable to an active analog telephone wall jack.

3 Change the distinctive rings setting to match the setting you want for the scanner to answer.
> Settings > Fax Settings > Analog Fax Setup b From the Answer On field, select the distinctive rings setting you want, and then touch Submit.
1 Type the scanner IP address in the address field of your Web browser.
If you do not know the IP address of the scanner, then you can:
2 Click Settings > Fax Settings > Analog Fax Setup.
3 In the Fax Name or Station Name field, enter the name to be printed on all outgoing faxes.
4 In the Fax Number or Station Number field, enter the printer fax number.
5 Click Submit.
You can set the date and time so that they are printed on every fax you send.
1 Open a Web browser, and then type the scanner IP address in the address field.
Faxing 132

2 Click Settings > Security > Set Date and Time.
3 In the Manually Set Date & Time field, enter the current date and time.
4 Click Submit.
The scanner can be set to automatically adjust for daylight saving time:
1 Type the scanner IP address in the address field of your Web browser.
If you do not know the IP address of the scanner, then you can:
2 Click Security > Set Date and Time.
3 Select the Automatically Observe DST check box, and then enter the DST start and end dates in the Custom Time Zone Setup section.
4 Click Submit.
You can use the scanner to send a fax to one or more recipients in a number of ways. You can type the e‑mail address, use a shortcut number or use the address book. You can also use the Multi Send or MyShortcut application from the scanner home screen. For more information, see “Activating the home screen applications” on page 21.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Fax.
Faxing 133

4 Enter the fax number or a shortcut using the touch screen or keypad.
To add recipients, touch Next Number and then enter the recipient's telephone number or shortcut number, or search the address book.
5 Touch Fax It.
The printer driver fax option allows you to “print to fax,” where the scanner will send a queued document as a fax rather than print it. The fax option functions as a normal fax machine, but is controlled through the printer driver instead of the scanner control panel.
1 With a document open, click File > Print.
2 Select the printer, and then navigate to:
Properties > Fax tab > Enable fax
3 Enter the recipient fax number in the “Fax number(s)” field.
Fax numbers can be entered manually or by using the Phone Book feature.
4 If necessary, enter a prefix in the Dialing prefix field.
5 Select the appropriate paper size and page orientation.
6 If you want to include a cover page with the fax, then select Include cover page with fax, and enter the appropriate information.
7 Click OK.
Fax shortcuts are just like the speed dial numbers on a telephone or fax machine. A shortcut number (1–99999) can contain a single recipient or multiple recipients.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
Faxing 134

, and then enter the shortcut number using the keypad.
4 Touch Fax It.
The address book enables you to search for bookmarks and network directory servers.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
4 Using the virtual keyboard, type the name or part of the name of the person whose fax number you want to find.
5 Touch Done > Fax It.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Fax > enter the fax number > Options > Delayed Send
4 Touch the arrows to adjust the time the fax will be transmitted.
The time is increased or decreased in increments of 30 minutes. If the current time is shown, then the left arrow is unavailable.
5 Touch Fax It.

Instead of entering the entire phone number of a fax recipient on the scanner control panel each time you want to send a fax, you can create a permanent fax destination and assign a shortcut number. A shortcut can be created to a single fax number or a group of fax numbers.
1 Type the scanner IP address in the address field of your Web browser.
If you do not know the IP address of the scanner, then you can:
2 Click Settings > Manage Shortcuts > Fax Shortcut Setup.
3 Type a unique name for the shortcut, and then enter the fax number.
To create a multiple‑number shortcut, enter the fax numbers for the group.
4 Assign a shortcut number.
If you enter a number that is already in use, then you are prompted to select another number.
5 Click Add.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Fax, and then enter the fax number.
To create a group of fax numbers, touch Next number, and then enter the next fax number.
4 Navigate to:
> type a name for the shortcut > Done > OK > Fax It
Faxing 136

Settings range from Standard (fastest speed) to Ultra Fine (slowest speed, best quality).
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Fax > enter the fax number > Options
4 From the Resolution area, touch the arrows to change to the resolution you want.
5 Touch Fax It.
1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Fax > enter the fax number > Options
4 Adjust the fax darkness, and then touch Fax It.
1 Type the scanner IP address in the address field of your Web browser.
If you do not know the IP address or host name of the scanner, then you can:
2 Click Settings > Reports > Fax Job Log or Fax Call Log.
1 Type the scanner IP address in the address field of your Web browser.
Faxing 137

If you do not know the IP address or host name of the scanner, then you can:
2 Click Settings > Fax Settings > Analog Fax Setup > Block No Name Fax.
1 On the home screen, touch Cancel Jobs.
The Cancel Jobs screen appears.
2 Touch the job or jobs you want to cancel.
Only three jobs appear on the screen; touch the down arrow until the job you want appears, and then touch the job you want to cancel.
3 Touch Delete Selected Jobs.
The Deleting Selected Jobs screen appears, the selected jobs are deleted, and then the home screen appears.
This option lets you hold received faxes from printing until they are released. Held faxes can be released manually or at a scheduled day or time.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Fax Settings > Analog Fax Setup > Holding Faxes.
Faxing 138

4 If you selected Scheduled, then continue with the following steps: a Click Fax Holding Schedule. b From the Action menu, select Hold faxes.
c From the Time menu, select the time you want the held faxes released. d From the Day(s) menu, select the day you want the held faxes released.
5 Click Add.
This option lets you print and forward received faxes to a fax number, e‑mail address, FTP site, or LDSS.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Fax Settings.
3 From the Fax Forwarding menu, select Print, Print and Forward, or Forward.
4 From the “Forward to” menu, select Fax, E‑mail, FTP, LDSS, or eSF.
5 In the “Forward to Shortcut” field, enter the shortcut number where you want the fax forwarded.
6 Click Submit.
This option lets you adjust the quality of the fax output. Increasing the image resolution increases the file size and the time needed to scan your original document. Decreasing the image resolution reduces the file size.
Select one of the following:
Faxing 139

This option lets you adjust how light or dark the faxes are in relation to the original document.
This option lets you change the following settings:
This option lets you specify the content type and source of the original document.
Select from the following content types:
Select from the following content sources:
This option lets you send a fax at a later time or date.
This option displays the first page of the image before it is included in the fax. When the first page is scanned, the scanning is paused and a preview image appears.
Faxing 140

Select from the following settings:
Faxing 141

Using Scan to Network
Scan to Network lets you scan your documents to network destinations specified by your system support person. After the destinations (shared network folders) have been established on the network, the setup process for the application involves installing and configuring the application on the appropriate printer using its Embedded Web Server. For more information, see “Setting up Scan to Network” on page 24.
Automatic document feeder (ADF) Scanner glass
Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
The scanner lets you scan documents directly to a File Transfer Protocol (FTP) server. Only one FTP address may be sent to the server at a time.
When an FTP destination has been configured by your system support person, the name of the destination becomes available as a shortcut number or it is listed as a profile under the Held Jobs icon. An FTP destination could also be another PostScript printer; for example, a color document can be scanned, and then sent to a mono printer.
Instead of entering the entire FTP site address on the scanner control panel each time you want to send a document to an FTP server, you can create a permanent FTP destination and assign a shortcut number. There are two methods for creating shortcut numbers: using the Embedded Web Server and using the scanner control panel.
1 Type the scanner IP address in the address field of your Web browser.
Scanning 142

If you do not know the IP address or host name of the scanner, then you can:
2 Click Settings.
3 Under Other Settings, click Manage Shortcuts.
4 Click FTP Shortcut Setup.
5 Enter the appropriate information.
6 Enter a shortcut number.
If you enter a number that is already in use, then you are prompted to select another number.
7 Click Add.
1 From the scanner home screen, navigate to:
FTP > FTP > type the FTP address >
> type a name for the shortcut > Done
2 Verify that the shortcut name and number are correct, and then touch OK.
You can use the scanner to send scanned documents to an FTP address in a number of ways. You can type the FTP address, use a shortcut number, or use the address book. You can also use the Multi Send, Scan to Network, or MyShortcut application from the scanner home screen. For more information, see “Activating the home screen applications” on page 21.
1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the scanner control panel, navigate to:
FTP > FTP > type the FTP address > Done > Send It
Scanning 143

1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the scanner control panel, press # on the keypad, and then enter the FTP shortcut number.
> Send It.
1 Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
> type the name of the recipient > Search
4 Touch the name of the recipient.
> Send It.
Scanning 144 · 4 Touch · 5 Touch

Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
The scanner lets you scan documents directly to a computer or to a flash drive. The computer does not have to be directly connected to the printer for you to receive Scan to PC images. You can scan the document back to the computer over the network by creating a scan profile on the computer, and then downloading the profile to the printer.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Scan Profile > Create Scan Profile.
3 Select your scan settings, and then click Next.
4 Select a location on your computer where you want to save the scan image.
5 Type a scan name.
6 Click Submit.
7 Review the instructions on the Scan Profile screen. a Load an original document facedown, long edge first into the ADF tray or facedown on the scanner glass.
Scanning 145 · ADF Scanner glass

c Do either of the following:
8 View the file from the computer.
1 Open the printers folder, and then select your scanner.
2 Open the scanner properties, and then adjust the settings as necessary.
3 From the control panel, touch Scan to Computer > select the appropriate scan setting > Send It.
1 Load an original document facedown into the ADF or on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 Insert the flash drive into the USB port on the side of the scanner control panel.
The USB Drive home screen appears.
4 Select the destination folder, and then navigate to:
Scan to USB drive > adjust the scan settings > Scan It
This option lets you enter the IP address for the FTP destination.
Scanning 146

This option lets you type a file name for the scan image.
This option lets you save the current settings as a shortcut by assigning a shortcut name.
This option lets you set the paper size of the documents you are going to scan. When Original Size is set to Mixed Sizes, you can scan an original document that contains mixed paper sizes (letter‑ and legal‑size pages).
This option lets you adjust how light or dark the scanned documents are in relation to the original document.
This option lets you adjust the output quality of your file. Increasing the image resolution increases the file size and the time needed to scan your original document. Decreasing the image resolution reduces the file size.
This option lets you set the output type for the scan image.
Select one of the following:
This option lets you set the original document type and source.
Select from the following content types:
Scanning 147

Select from the following content sources:
This option lets you change the following settings:
This option displays the first page of the original document before it is scanned completely. When the first page is scanned, the scanning is paused and a preview image appears.
Select from the following settings:
Scanning 148

Understanding the printer menus 149
Menus list
Paper Menu Reports Network/Ports Security Settings
Default Source Paper Size/Type
Menu Settings Page Device Statistics
Edit Security Setups Miscellaneous Security
General Settings Copy Settings
E‑mail Settings
Parallel [x] Serial [x]
Erase Temporary Data Files
Fax Job Log Fax Call Log
Set Date and Time
Custom Names Custom Scan Sizes
Print Directory Asset Report
Help Manage Shortcuts Option Card Menu2
A list of installed DLEs (Download Emulators) appears.
Fax Guide FTP Guide
Copy Shortcuts Profile Shortcuts
1 Depending on the scanner setup, this menu appears as Standard Network or Network [x].
2 This menu appears only when one or more DLEs are installed.

Understanding the printer menus 150
Provides the option to reset the supply counter for the separator pad and pick roller
Separator Pad Pick Roller
Shows the status of the separator pad
Shows the status of the pick roller
Set a default paper source for all print jobs.
Tray [x] Multipurpose Feeder Manual Paper
Determine when the printer selects paper from the multipurpose feeder.

Understanding the printer menus 151
Specify the paper size loaded in each tray.
A4 A5 A6 JIS‑B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the type of paper loaded in each tray.
Plain Paper Card Stock Transparency Recycled Labels Vinyl Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Use To · Tray [x] Size · Tray [x] Type

Understanding the printer menus 152
Specify the paper size loaded in the multipurpose feeder.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the paper type loaded in the multipurpose feeder.
Plain Paper Card Stock Transparency Recycled Labels Vinyl Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Use To · MP Feeder Size · MP Feeder Type

Understanding the printer menus 153
Specify the size of the paper being manually loaded.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the paper type being manually loaded.
Plain Paper Card Stock Transparency Recycled Labels Vinyl Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Specify the envelope size being manually loaded.
7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the envelope type being manually loaded.
Envelope Rough Envelope Custom Type [x]

Understanding the printer menus 154
Default ADF Media Type
Specify the media type being loaded in the ADF.
Plain Paper Card Stock Transparency Recycled Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom [x]
Substitute a specified paper size if the requested paper size is not available.
Off Statement/A5 Letter/A4 All Listed
Specify the relative texture of the plain paper loaded in a specific tray.
Specify the relative texture of the card stock loaded in a specific tray.

Understanding the printer menus 155
Specify the relative texture of the transparencies loaded in a specific tray.
Specify the relative texture of the recycled paper loaded in a specific tray.
Specify the relative texture of the labels loaded in a specific tray.
Specify the relative texture of the vinyl labels loaded in a specific tray.
Specify the relative texture of the bond paper loaded in a specific tray.
Specify the relative texture of the envelopes loaded in a specific tray.
Specify the relative texture of the rough envelopes loaded in a specific tray.
Specify the relative texture of the letterhead loaded in a specific tray.
Specify the relative texture of the preprinted paper loaded in a specific tray.
Specify the relative texture of the colored paper loaded in a specific tray.

Understanding the printer menus 156
Specify the relative texture of the light paper loaded in a specific tray.
Specify the relative texture of the heavy paper loaded in a specific tray.
Specify the relative texture of the rough or cotton paper loaded in a specific tray.
Specify the relative texture of the custom paper loaded in a specific tray.
Specify the relative weight of the plain paper loaded.
Specify the relative weight of the card stock loaded.
Specify the relative weight of the transparencies loaded.
Specify the relative weight of the recycled paper loaded.
Specify the relative weight of the labels loaded.
Specify the relative weight of the vinyl labels loaded.

Understanding the printer menus 157
Specify the relative weight of the bond paper loaded.
Specify the relative weight of the envelope loaded.
Specify the relative weight of the rough envelope loaded.
Specify the relative weight of the letterhead loaded.
Specify the relative weight of the preprinted paper loaded.
Specify the relative weight of the colored paper loaded.
Specify that the weight of the paper loaded is light.
Specify that the weight of the paper loaded is heavy.
Specify the relative weight of the cotton or rough paper loaded.
Specify the relative weight of the custom paper loaded.

Understanding the printer menus 158
Determine and set two-sided printing for all print jobs with Card Stock as the paper type.
Determine and set two-sided printing for all print jobs with Recycled as the paper type.
Determine and set two-sided printing for all print jobs with Labels as the paper type.
Determine and set two-sided printing for all print jobs with Vinyl Labels as the paper type.
Determine and set two-sided printing for all print jobs with Bond as the paper type.
Determine and set two-sided printing for all print jobs with Letterhead as the paper type.
Determine and set two-sided printing for all print jobs with Preprinted as the paper type.
Determine and set two-sided printing for all print jobs with Colored as the paper type.
Determine and set two-sided printing for all print jobs with Light as the paper type.
Determine and set two-sided printing for all print jobs with Heavy as the paper type.
Determine and set two-sided printing for all print jobs with Rough or Cotton as the paper type.

Understanding the printer menus 159
Determine and set two-sided printing for all print jobs with Custom [x] as the paper type.
Associate a paper or specialty media type with a factory default custom type name or a user‑defined custom name created from the Embedded Web Server or from MarkVisionTM Professional.
Paper Card Stock Transparency Rough/Cotton Labels Vinyl Labels Envelope
Specify a paper type when Recycled is selected in other menus.
Paper Card Stock Transparency Rough/Cotton Labels Vinyl Labels Envelope
Custom Name [x] Specify a custom name for a paper type. This name replaces Custom Type [x] in the printer menus.

Understanding the printer menus 160
Custom Scan Size [x]
Specify a custom scan size name, scan sizes, and options. The custom scan size name replaces Custom Scan Size [x] in the scanner menus.
Scan Size Name Media Type
Plain Paper Card Stock Transparency Recycled Labels Vinyl Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x] Width
1–8.5 in. (25–216 mm) Height
1–25 in. (25–635.0 mm) Orientation
Portrait Landscape 2 scans per side Off On
Standard Bin Specify a custom name for the standard bin.
Bin [x] Specify a custom name for Bin [x].
Use To · ADF Media Type · Use To

Understanding the printer menus 161
Identify the units of measure.
Set the portrait width.
3–8.5 inches 76–216 mm
Set the portrait height.
3–14.17 inches 76–360 mm
Specify the feed direction if the paper can be loaded in either direction.
Short Edge Long Edge
Specify the default bin.
Standard Bin Bin [x]

Understanding the printer menus 162
Specify configuration options for bins.
Mailbox Link Mail Overflow Link Optional Type Assignment
Specify an alternative bin when a designated bin is full.
Standard Bin Bin [x]
Select a bin for each supported paper type.
Plain Paper Bin Card Stock Bin Transparency Bin Recycled Bin Labels Bin Vinyl Labels Bin Bond Bin Envelope Bin Rough Envelope Bin Letterhead Bin Preprinted Bin Colored Bin Light Paper Bin Heavy Paper Bin Rough/Cotton Bin Custom [x] Bin
For each type, select from the following options:
Disabled Standard Bin Bin [x]

Understanding the printer menus 163
Menu Settings Page Prints a report containing information about the paper loaded into trays, installed memory, total page count, alarms, timeouts, scanner control panel language, TCP/IP address, status of supplies, status of the network connection, and other information
Device Statistics Prints a report containing printer statistics such as supply information and details about printed pages
Network Setup Page Prints a report containing information about the network scanner settings, such as the TCP/IP address information
Network [x] Setup Page Prints a report containing information about the network scanner settings, such as the TCP/IP address information
Shortcut List Prints a report containing information about configured shortcuts
Fax Job Log Prints a report containing information about the last 200 completed faxes
Fax Call Log Prints a report containing information about the last 100 attempted, received, and blocked calls
Copy Shortcuts Prints a report containing information about copy shortcuts
E‑mail Shortcuts Prints a report containing information about e‑mail shortcuts
Fax Shortcuts Prints a report containing information about fax shortcuts
FTP Shortcuts Prints a report containing information about FTP shortcuts
Profiles List Prints a list of profiles stored in the scanner
Print Fonts Prints a report of all the fonts available for the language currently set in the scanner
Menu item Description
![Page 164 of the Lexmark MX6500E user manual — Standard Network or Network [x] menu](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-164.webp?w=400)
Understanding the printer menus 164
Print Directory Prints a list of all the resources stored on an optional flash memory card or scanner hard disk
Asset Report Prints a report containing asset information including the scanner serial number and model name. The report contains text and UPC barcodes that can be scanned into an asset database.
Auto [list of available network cards]
Sets the scanner to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language
Sets the scanner to automatically switch to PS emulation when a print job requires it, regardless of the default printer language

Understanding the printer menus 165
Sets the scanner to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol
Sets the size of the network input buffer
Auto 3KB to [maximum size allowed]
Temporarily stores print jobs on the scanner hard disk before printing. This menu only appears if a formatted disk is installed.
Sets the scanner to process Macintosh binary PostScript print jobs

Understanding the printer menus 166
Displays and sets network settings
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
To access the menu, navigate to either of the following:
Print Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address.
To access the menu, navigate to either of the following:
View the connection status of the wireless network adapter.
View Card Speed View the speed of an active wireless network adapter.
View the network addresses.

Understanding the printer menus 167
Set the amount of time it takes for a network print job to be canceled.
Allow the printer to print a banner page.
To access the menu, navigate to either of the following:
Set Hostname Set the current TCP/IP host name.
IP Address View or change the current TCP/IP address.
Netmask View or change the current TCP/IP netmask.
Gateway View or change the current TCP/IP gateway.
Specify the DHCP address and parameter assignment.
Specify the RARP address assignment setting.
Specify the BOOTP address assignment setting.
Specify the Zero Configuration Networking setting.
Enable the built-in FTP server, which lets you send files to the scanner using File Transfer Protocol.

Understanding the printer menus 168
Enable the built-in Web server (Embedded Web Server). When enabled, the scanner can be monitored and managed remotely using a Web browser.
WINS Server Address View or change the current WINS server address.
View or change the current DDNS setting.
View or change the current mDNS setting.
DNS Server Address View or change the current DNS server address.
Backup DNS Server Address View or change the backup DNS server addresses.
Backup DNS Server Address 2
Backup DNS Server Address 3
View or change the current HTTPS setting.
To access the menu, navigate to any of the following:
Enable Internet Protocol Version Six (IPv6) in the printer. IPv6 uses bigger numbers to create IP addresses.
Specify whether or not the network adapter accepts the automatic IPv6 address configuration entries provided by a router.
Set Hostname* Set the host name.
View Address* View the current IPv6 addresses.
View Router Address* View the current router address.
* These settings can be changed only from the Embedded Web Server.

Understanding the printer menus 169
Enable DHCPv6 in the printer.
* These settings can be changed only from the Embedded Web Server.
To access the menu, navigate to:
Network/Ports > Network [x] > Network [x] Setup > Wireless
Wi‑Fi Protected Setup
Establish a wireless network and enable network security.
Start Push Button Method Start PIN Method
Enable/Disable WPS Auto‑detection
Automatically detect the connection method that an access point with WPS uses—Start Push Button Method or Start PIN Method.
Specify the network mode.
Specify the wireless standard for the wireless network.
802.11b/g 802.11b/g/n
Choose Network Select an available network for the printer to use.
View Signal Quality View the quality of the wireless connection.
View Security Mode View the encryption method for the wireless network.

Understanding the printer menus 170
To access the menu, navigate to either of the following:
Enable or disable AppleTalk support.
View Name Show the assigned AppleTalk name.
View Address Show the assigned AppleTalk address.
Provide a list of AppleTalk zones available on the network.
[list of zones available on the network]
Sets the scanner to automatically switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language
Sets the scanner to automatically switch to PS emulation when a print job received through a USB port requires it, regardless of the default language

Understanding the printer menus 171
Sets the scanner to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol
Sets the size of the USB input buffer
Auto 3KB to [maximum size allowed] Disabled
Temporarily stores print jobs on the scanner hard disk before printing
Sets the scanner to process Macintosh binary PostScript print jobs
Sets the network address information for an external print server
yyy.yyy.yyy.yyy
Sets the netmask information for an external print server
yyy.yyy.yyy.yyy
![Page 172 of the Lexmark MX6500E user manual — Parallel [x] menu](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-172.webp?w=400)
Understanding the printer menus 172
Sets the gateway information for an external print server
yyy.yyy.yyy.yyy
Sets the scanner to automatically switch to PCL emulation when a print job received through a serial port requires it, regardless of the default language
Sets the scanner to automatically switch to PS emulation when a print job received through a serial port requires it, regardless of the default language
Sets the scanner to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol
Sets the size of the parallel input buffer
Auto 3KB to [maximum size allowed] Disabled
![Page 173 of the Lexmark MX6500E user manual — Parallel [x] menu](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-173.webp?w=400)
Understanding the printer menus 173
Temporarily stores print jobs on the scanner hard disk before printing
Enables bidirectional communication through the parallel port
Specifies the parallel port protocol
Determines if the scanner honors hardware initialization requests from the computer
Determines if the parallel port data is sampled on the leading or trailing edge of a strobe
Sets the printer to process Macintosh binary PostScript print jobs
Sets the network address information for an external print server
yyy.yyy.yyy.yyy
Sets the netmask information for an external print server
yyy.yyy.yyy.yyy
![Page 174 of the Lexmark MX6500E user manual — Serial [x] menu](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-174.webp?w=400)
Understanding the printer menus 174
Sets the gateway information for an external print server
yyy.yyy.yyy.yyy
Sets the scanner to automatically switch to PCL emulation when a print job received through a serial port requires it, regardless of the default printer language
Sets the scanner to automatically switch to PS emulation when a print job received through a serial port requires it, regardless of the default printer language
Sets the scanner to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol

Understanding the printer menus 175
Sets the size of the serial input buffer
Auto 3KB to [maximum size allowed] Disabled
Temporarily stores print jobs on the scanner hard disk before printing
Selects the hardware and software handshaking settings for the serial port
Determines whether the scanner communicates availability to the computer

Understanding the printer menus 176
Specifies the rate at which data can be received through the serial port
9600 19200 38400 57600 115200 138200 172800 230400 345600 1200 2400 4800
Specifies the number of data bits sent in each transmission frame
Sets the parity for serial input and output data frames
None Ignore Even Odd
Determines whether the scanner uses the DSR Signal
Primary SMTP Gateway Specifies SMTP server gateway and port information
Secondary SMTP Gateway Port
5–30 Specifies the amount of time in seconds before the server stops trying to send an e‑mail
Reply Address Specifies a reply address of up to 128 characters in the e-mail sent by the printer

Understanding the printer menus 177
Sets the printer to use SSL for increased security when connecting to the SMTP server
Specifies the type of user authentication required for scan to e‑mail privileges
No authentication required Login/Plain CRAM‑MD5 Digest‑MD5 NTLM Kerberos 5
Device‑Initiated E‑mail
Specifies what credentials will be used when communicating to the SMTP server. Some SMTP servers require credentials to send an e-mail.
None Use Device SMTP Credentials
User‑Initiated E‑mail
None Use Device SMTP Credentials Use Session User ID & Password Use Session E‑mail address & Password Prompt User
Create a backup password.

Understanding the printer menus 178
Edit settings for Internal Accounts, NTLM, Simple Kerberos Setup, Kerberos Setup, Active Directory, LDAP, Password, and PIN.
Internal Accounts NTLM Simple Kerberos Setup Kerberos Setup Active Directory LDAP LDAP+GSSAPI Password PIN
Add or edit a security template.
[list of available templates]
Control access to printer menus, firmware updates, held jobs, and other access points.
Administrative Menus Function Access Apps Configuration Management Solutions Cancel Jobs at the Device
Limits the number and time frames of failed login attempts from the scanner control panel before all users are locked out
Login failures Failure time frame Lockout time Panel Login Timeout Remote Login Timeout

Understanding the printer menus 179
Changes the value of the security settings
Access controls=”No Security” No Effect Reset factory security defaults
Allows the user to request a server certificate
Demand Try Allow Never
1–16 Limits the digit length of the PIN.
Limits the number of times an invalid PIN can be entered
Limits the amount of time a “confidential” print job is saved before it is deleted
Off 1 hour 4 hours 24 hours 1 week

Understanding the printer menus 180
Limits the amount of time a “repeat” print job is saved before it is deleted
Off 1 hour 4 hours 24 hours 1 week
Limits the amount of time a “verify” print job is saved before it is deleted
Off 1 hour 4 hours 24 hours 1 week
Limits the amount of time a “reserve” print job is saved before it is deleted
Off 1 hour 4 hours 24 hours 1 week
This menu allows you to remove residual confidential material from the scanner hard disk and free up memory space. All permanent data on the hard disk are preserved, such as downloaded fonts, macros, and held jobs. This uses random data patterns to securely overwrite files stored on the hard drive that have been marked for deletion. Overwriting can be accomplished with a single pass‑‑for a quick wipe‑‑or with multiple passes with greater security.
Specify the mode for disk wiping.
Mark all disk space used by a previous print job. This method does not permit the file system to reuse this space until it has been cleared.
Single pass Multiple pass

Understanding the printer menus 181
Export Log Let an authorized user export the audit log.
Specify whether to delete audit logs.
Configure the printer to record events in the secure audit log.
Yes No Enable Remote Syslog
No Yes Remote Syslog Facility
0–23 Severity of events to log
Current Date and Time View the current date and time settings for the scanner.
Manually Set Date and Time Enter the date and time.
Time Zone Select the time zone.
Set the scanner to use the applicable daylight saving time (DST) start and end times associated with the scanner Time Zone setting.

Understanding the printer menus 182
Custom Time Zone Setup
Enable the user to set up the time zone.
DST Start Week DST Start Day DST Start Month DST Start Time DST End Week DST End Day DST End Month DST End Time DST Offset
Enable Network Time Protocol, which synchronizes the clocks of devices on a network.
NTP Server View the NTP server address.
Enable the authentication setting.

Understanding the printer menus 183
Set the language of the text appearing on the display.
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portuguese Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese
View the estimates of the supplies on the control panel, Embedded Web Server, menu settings, and device statistics reports.
Show estimates Do not show estimates
Minimize the use of energy, paper, or specialty media.
Off Energy Energy/Paper Paper
Specify whether the ADF sounds a beep when paper is loaded.

Understanding the printer menus 184
ADF Multi‑feed Sensor
Detect when the ADF picks more than a single sheet of paper at once.
Minimize the printer noise.
Run the setup wizard.
Specify a language and custom key information for the display keyboard.
English Francais Francais Canadien Deutsch Italiano Espanol Greek Dansk Norsk Nederlands Svenska Suomi Portuguese Russian Polski Swiss German Swiss French Korean Magyar Turkce Cesky Simplified Chinese Traditional Chinese Japanese Custom Key [x]
Specify the unit of measurement for paper sizes.

Understanding the printer menus 185
Scan to PC Port Range
Specify a valid port range for scanners behind a port blocking firewall.
Specify what is displayed in the upper corners of the home screen.
Left side Right side Custom Text [x]
For the Left side and Right side menus, select from the following options:
None IP Address Hostname Contact Name Location Date/Time mDNS/DDNS Service Name Zero Configuration Name Custom Text [x] Model Name
Customize the displayed information for Black Toner.
Select from the following options:
Do not display Display Message to display

Understanding the printer menus 186
Customize the displayed information for Paper Jam, Load Paper, and Service Errors menus.
Paper Jam Load Paper Service Errors
Select from the following options:
Yes No Message to display
Change the icons that appear on the home screen.
Change Language Copy Copy shortcuts Fax Fax shortcuts E‑mail E‑mail shortcuts FTP FTP shortcuts Search Held Jobs Held Jobs USB Drive Profiles and Apps Bookmarks Jobs by user Forms and Favorites Card Copy Scan to Network MyShortCut Multi Send
For each icon, select from the following options:
Display Do Not display
Format the date.
MM‑DD‑YYYY DD‑MM‑YYYY YYYY‑MM‑DD
Format the time.
12 hour A.M./P.M. 24 hour clock
20–100 Specify the brightness of the control panel screen.

Understanding the printer menus 187
Set copies from the scanner glass to only one page at a time.
Set the amount of light from the standard bin.
Set the audio volume for the buttons.
Provide touch‑screen sensation feedback.
Specify whether bookmarks are displayed from the Held Jobs area.
Specify whether image background removal is allowed.
Allow Custom Job Scans
Scan multiple jobs to one file.
Specify how a scanned job should be reloaded if a paper jam occurs in the ADF.
Job level Page level
Web Page Refresh Rate
30–300 Specify the number of seconds between Embedded Web Server refreshes.
Contact Name Specify a contact name.
Location Specify the location.

Understanding the printer menus 188
Set an alarm to sound when operator intervention is required.
Alarm Control Cartridge Alarm Staple Alarm Hole Punch Alarm
For each alarm type, select from the following options:
Set the amount of time in minutes before the scanner enters a lower power state.
Set the amount of time in minutes the scanner waits after a job is printed before the scanner and the printer go into a reduced power state.
Disabled 1‑120
Print a job while the display is off.
Print with Display Off
Allow printing with display off Display on when printing
Set the amount of time in seconds before returning the control panel to a Ready state.
Continue a specified job without returning to the home screen when the screen timeout timer expires.

Understanding the printer menus 189
Set the amount of time in seconds the scanner waits to receive an end‑of‑job message before canceling the rest of the print job.
Set the amount of time in seconds the scanner waits for additional data before canceling a print job.
Set the amount of time the scanner waits for user intervention before it holds jobs that require unavailable resources and continues to print other jobs in the print queue.
Set the scanner and the printer to restart when an error occurs.
Reboot when idle Reboot always Reboot never
Determine the number of automatic reboots the printer can perform.
Let the printer automatically continue printing from certain offline situations when these are not resolved within the specified time period.

Understanding the printer menus 190
Specify whether the printer reprints jammed pages.
Successfully print a page that may not have printed otherwise.
Determine how the printer, while in idle state, reacts to a short press of the Sleep button.
Press and Hold Sleep Button
Determine how the printer, while in idle state, reacts to a long press of the Sleep button.
Use the printer factory default settings.
Do Not Restore Restore Now
Export configuration files to a flash drive.
Specify the content of the original document.
Text Graphics Text/Photo Photo

Understanding the printer menus 191
Specify how the original document was produced.
Black/White Laser Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify whether an original document is two‑sided (duplex) or one‑sided, and then to specify whether the copy should be two‑sided or one‑sided.
1 sided to 1 sided 1 sided to 2 sided 2 sided to 1 sided 2 sided to 2 sided
Copy two or four sheets of a document on one page.
Off 2‑up Portrait 4‑up Portrait 2‑up Landscape 4‑up Landscape
Specify whether or not a border is printed.
Keep the pages of a print job stacked in sequence when printing multiple copies.
1,1,1 ‑ 2,2,2 1,2,3 ‑ 1,2,3
Specify the type of hole punch finishing to be used in a print or copy job.
Off 2 holes 3 holes 4 holes
Enable or disable the staple finisher.

Understanding the printer menus 192
Specify the paper size of the original document.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense A4 A5 A6 JIS B5 Difficult Media Letter Difficult Media A5 Difficult Media Legal Difficult Media A4 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in. ID Card
Specify the paper source for copy jobs.
Tray [x] Auto Size Match Multipurpose Feeder
Place a sheet of paper between transparencies.
Place a sheet of paper between pages, copies, or jobs.
Off Between Copies Between Jobs Between Pages
Specify the separator sheet source.
Tray [x] Multipurpose Feeder
1–9 Lighten or darken the print for the copy job.
1–999 Specify the number of copies for the copy job.

Understanding the printer menus 193
Specify header and footer information and its location on the page.
For the location, select from the following options:
Off Date/Time Page number Custom text Print on
All pages First page only All but first page Custom text
Specify the overlay text printed on each page of the copy job.
Confidential Copy Draft Urgent Custom Off
Custom Overlay Specify the custom overlay text.
Allow interruption of a print job to copy a page or document.
Copy a document that contains mixed paper sizes into a single copy job.
Allow Save as Shortcut
Save custom copy settings as shortcuts.
Adjust the amount of background visible on a copy.
‑4 to 4
Automatically center the content on the page.

Understanding the printer menus 194
Specify which color to drop during scanning, and how much the dropout is increased or decreased.
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specify the contrast used for the copy job.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a copy.
‑4 to 4
Correct the slight skew in the scanned image.
ADF Multi‑feed Sensor
Detect when the ADF picks more than a single sheet of paper at once.
Scan edge to edge
Specify whether the original document is scanned edge-to-edge.
1–5 Adjust the amount of sharpness of a copy.
Create a sample copy of the original document.

Understanding the printer menus 195
Analog Fax Setup mode sends the fax job through a telephone line.
Fax Name Specify the name of the fax in the scanner.
Fax Number Specify the number assigned to the fax.
Specify how the fax is identified.
Fax Name Fax Number
Set the scanner to fax manually, which requires a line splitter and a telephone handset.
Define the allocation of non-volatile memory between sending and receiving fax jobs.
All receive Mostly receive Equal Mostly send All send
Specify whether or not the scanner cancels fax jobs.
Specify the type of caller ID being used.
Specify the direction from where digits are masked in an outgoing fax number.
Off From left From right
0–58 Specify the number of digits to mask in an outgoing fax number.

Understanding the printer menus 196
Configure the fax cover page.
Off by default On by default Never use Always use Include to Field
On Off Include from Field
On Off From Include Message Field
On Off Message Include Logo
On Off Include Footer [x]
On Off Footer [x]
Specify quality in dots per inch (dpi). A higher resolution gives better print quality, but increases the fax transmission time for outgoing faxes.
Standard Fine 200 dpi Super Fine 300 dpi Ultra Fine 600 dpi

Understanding the printer menus 197
Specify the paper size of the original document.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in.
Specify how text and graphics are oriented on a page.
Off Long edge Short edge
Specify the content of the original document.
Text Graphics Text/Photo Photo
Specify how the original document was produced.
Black/White Laser Inkjet Photo/Film Magazine Newspaper Press Other
1–9 Adjust the darkness of the output.
Dial Prefix Enter a dialing prefix, such as 99. A numeric entry field is provided.

Understanding the printer menus 198
Establish a dialing prefix rule.
0–9 Specify the number of times the scanner tries to send the fax to a specified number.
1–200 Specify the number of minutes between redials.
Enable or disable switchboard blind dialing without a dial tone.
Enable or disable Error Correction Mode for fax jobs.
Fax files that are scanned at the scanner.
Allow the printer driver to send fax jobs.
Allow Save as Shortcut
Save fax numbers as shortcuts in the scanner.
Specify the dialing sound, either as a tone or as a pulse.
Specify the maximum speed in baud at which faxes are sent.
2400 4800 9600 14400 33600
Scan a document that contains mixed paper sizes into a single file.
Specify whether a preview will appear on the display for scan jobs.
Adjust the amount of background visible on a scanned image.
‑4 to 4
Specify the contrast in the scanned image.
0–5 Best for content

Understanding the printer menus 199
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible.
‑4 to 4
Correct the slight skew in the scanned image.
Allow the scanner to detect when the ADF picks more than one sheet of paper at once.
Specify if the original document is scanned edge-to‑edge prior to faxing.
Scan edge to edge
1–5 Adjust the sharpness of a fax.
Specify “warm” or “cool” outputs. “Cool” values generate a bluer output than the default while “warm” values generate a redder output than the default.
‑4 to 4
Allow the printer to receive fax jobs.
Remove fax jobs from the print queue when the job requires specific unavailable resources.
None Toner Toner and Supplies
1–25 Specify the number of rings before answering an incoming fax job.
Allow the scanner to answer an incoming fax job.

Understanding the printer menus 200
0–9 Enter a code on the telephone number pad to begin receiving a fax.
Scale an incoming fax job so that it fits the size of the paper loaded in the designated fax source.
Specify the paper source for printing incoming fax jobs.
Auto Tray [x] Multipurpose Feeder
Enable two‑sided (duplex) printing for incoming fax jobs.
Enable the printer to include separator sheets for incoming fax jobs.
Off Before Job After Job
Specify where the printer picks the separator sheet.
Tray [x] Multipurpose Feeder
Specify a bin for received faxes.
Standard Bin Bin [x]
Print the transmission information at the bottom of each page from a received fax.
Specify the maximum speed in baud at which faxes are received.
2400 4800 9600 14400 33600
Enable forwarding of received faxes to another recipient.
Print Print and Forward Forward

Understanding the printer menus 201
Specify the type of recipient to which faxes will be forwarded.
Fax E‑mail FTP LDSS eSF
Forward to Shortcut Enter the shortcut number which matches the recipient type (Fax, E-mail, FTP, LDSS, or eSF).
Block No Name Fax
Enable blocking of incoming faxes sent from devices with no station ID or fax ID specified.
Banned Fax List Enable the list of blocked fax numbers stored in the scanner.
Enable fax holding all of the time or according to set schedule.
Off Always On Manual Scheduled Fax Holding Schedule
Specify whether prints are punched.
Specify whether prints are stapled.
Enable printing of a transmission log after each fax job.
Print log Do not print log Print only for error
Enable printing of a receive error log following a receive error.
Print Never Print on Error
Enable automatic printing of fax logs.
Specify the paper source used for printing logs.
Tray [x] Multipurpose Feeder

Understanding the printer menus 202
Specify whether printed logs display the dialed number or the station name or fax name returned.
Remote Station Name Dialed Number
Enable access to the Fax Job log.
Enable access to the Fax Call log.
Specify the bin where fax logs are printed.
Standard Bin Bin [x]
Specify the mode of the speaker.
Always Off On until Connected Always On
Control the volume setting.
Control the fax speaker ringer volume.
All Rings Single Ring Only Double Ring Only Triple Ring Only Single or Double Rings Only Single or Triple Rings Only Double or Triple Rings Only
Specify ring patterns when the scanner is answering calls.

Understanding the printer menus 203
E‑mail Server Setup
Specify e‑mail server information.
Subject Message File Name
E‑mail Server Setup
Send a copy of the e-mail to the sender.
Send me a copy
Never appears On by default Off by default Always On
E‑mail Server Setup
Specify the maximum e-mail size in kilobytes (KB).
Max e‑mail size
E‑mail Server Setup
Send a message when an e-mail is bigger than the configured size limit.
E‑mail Server Setup
Specify a domain name, such as a company domain name, and then limits e‑mail destinations only to that domain name.
E‑mail Server Setup
Define the e‑mail server path name; for example: /directory/path.
Server Login Password Path File Name Web Link
Specify the format of the scanned file.
PDF (.pdf) Secure PDF TIFF (.tif) JPEG (.jpg) XPS (.xps)
Set the version of the PDF file that will be scanned for e‑mailing.
1.2–1.6 A–1a

Understanding the printer menus 204
Specify the content of the original document.
Graphics Text Text/Photo Photo
Specify how the original document was produced.
Black/White Laser Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify whether the image should be scanned and sent in color.
Specify the resolution of the scan in dots per inch.
75 dpi 150 dpi 200 dpi 300 dpi 400 dpi 600 dpi
1–9 Adjust the darkness of the output.
Specify the orientation of the scanned image.

Understanding the printer menus 205
Specify the paper size of the document being scanned.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Difficult Media Letter Difficult Media A5 Difficult Media Legal Difficult Media A4 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in.
Specify how text and graphics are oriented on the page.
Off Long edge Short edge
Set the quality of a JPEG photo image in relation to file size and quality of the image.
Best for content 5–90
5–90 Set the quality of a text image in relation to file size and quality of the image.
5–90 Set the quality of a text or photo image in relation to file size and the quality of the image.

Understanding the printer menus 206
5–90 Set the quality of a photo image in relation to file size and the quality of the image.
E‑mail images sent as
Specify how the images are sent.
Use Multi‑Page Tiff
Choose between single-page TIFF files and multiple‑page TIFF files. For a multiple- page scan‑to‑e-mail job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the job.
Specify whether or not the transmission log prints.
Print log Do not print log Print only for error
Specify the paper source for printing e-mail logs.
Tray [x] Multipurpose Feeder
Specify the bin for FTP logs.
Standard Bin Bin [x]
E‑mail Bit Depth
Enable the Text/Photo mode to produce smaller file sizes by using 1‑bit images when Color is set to Off.
1 bit 8 bit
Copy a document that contains mixed paper sizes.
Specify whether or not a preview will appear on the display for scan jobs.
Allow Save as Shortcut
Save e-mail addresses as shortcuts.
Adjust the amount of background visible on a scanned image.
‑4 to 4

Understanding the printer menus 207
Enable an equal balance of colors in the output.
Cyan - Red Magenta - Green Yellow - Blue
Specify which color to drop during scanning, and how much the dropout is increased or decreased.
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specify the contrast of the output.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4
Correct the slight skew in the scanned image.
ADF Multi‑feed Sensor
Detect when the ADF picks more than one sheet of paper at once.
Scan edge to edge
Specify whether the original document is scanned edge-to-edge.
1–5 Adjust the amount of sharpness on a scanned image.
Enable the user to specify “warm” or “cool” outputs. "Cool” values generate a bluer output than the default while “warm” values generate a redder output than the default.
‑4 to 4

Understanding the printer menus 208
Use cc:/bcc:
Enable the use of the “cc:” and “bcc:” fields.
Specify the format of the file for FTP sending.
PDF (.pdf) Secure PDF (.pdf) TIFF (.tif) JPEG (.jpg) XPS (.xps)
Set the version level of the PDF file for FTP sending.
1.2–1.7 A–1a
Specify the content of the original document.
Text Graphics Text/Photo Photo
Specify how the original document was produced.
Black/White Laser Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify whether or not an image is scanned or sent in color.
Specify the quality of the scan in dots per inch (dpi).
75 dpi 150 dpi 200 dpi 300 dpi 400 dpi 600 dpi
1–9 Adjust the darkness of the output.

Understanding the printer menus 209
Specify the page orientation of the scanned image.
Specify the paper size of the original document.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Difficult Media Letter Difficult Media A5 Difficult Media Legal Difficult Media A4 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in.
Specify the page orientation of text and graphics.
Off Long Edge Short Edge
Set the quality of a JPEG photo image in relation to the file size and quality of the image.
Best for content 5–90
5–90 Set the quality of the text in relation to the file size and quality of the image.

Understanding the printer menus 210
5–90 Set the quality of a text/photo image in relation to the file size and quality of the image.
5–90 Set the quality of a photo image in relation to the file size and quality of the image.
Use Multi‑Page TIFF
Provide a choice between single-page TIFF files and multiple‑page TIFF files. For a multiple-page scan‑to‑FTP job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the job.
Specify whether the transmission log prints.
Print log Do not print log Print only for error
Specify a paper source when printing FTP logs.
Tray [x] Multipurpose Feeder
Specify the bin for FTP logs.
Standard Bin Bin [x]
Enable the Text/Photo mode to have smaller file sizes by using 1‑bit images when Color is set to Off.
1 bit 8 bit
File Name Enter a base file name.
Copy a document that contains mixed paper sizes into a single scan job.
Specify whether a preview will appear on the display for scan jobs.
Allow Save as Shortcut
Enable shortcut creation for FTP addresses.

Understanding the printer menus 211
Adjust the amount of background visible on a copy.
‑4 to 4
Enable an equal balance of colors in the output.
Cyan - Red Magenta - Green Yellow - Blue
Specify which color to drop during scanning, and how much the dropout is increased or decreased.
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specify the contrast of the output.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4
Correct the slight skew in the scanned image.
ADF Multi‑feed Sensor
Detect when the ADF picks more than a single sheet of paper at once.
Scan edge to edge
Specify whether the original document is scanned edge-to-edge.
1–5 Adjust the amount of sharpness of a scanned image.

Understanding the printer menus 212
Enable the user to specify “warm” or “cool” outputs. "Cool” values generate a bluer output than the default while “warm” values generate a redder output than the default.
‑4 to 4
Specify the format of the file to be sent through FTP.
PDF (.pdf) Secure PDF TIFF (.tif) JPEG (.jpg) XPS (.xps)
Set the version of the PDF file to be sent through FTP.
1.2–1.7 A‑1a
Specify the content of the original document.
Text Graphics Text/Photo Photo
Specify how the original document is produced.
Black/White Laser Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify the resolution of the scan in dots per inch (dpi).
75 dpi 150 dpi 200 dpi 300 dpi 400 dpi 600 dpi
1–9 Adjust the darkness of the output.

Understanding the printer menus 213
Specify the page orientation of the scanned image.
Specify the paper size of the original document.
Letter Legal Executive Folio Statement Oficio (Mexico) Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Difficult Media Letter Difficult Media A5 Difficult Media Legal Difficult Media A4 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in.
Specify the page orientation of text and graphics.
Off Long Edge Short Edge
Set the quality of a JPEG photo image in relation to file size and quality.
Best for content 5–90
5–90 Set the quality of the text in relation to file size and the quality of the image.
5–90 Set the quality of a text/photo image in relation to file size and quality.

Understanding the printer menus 214
5–90 Set the quality of a photo image in relation to file size and quality.
Use Multi‑Page TIFF
Provide a choice between single-page TIFF files and multiple‑page TIFF files. For a multiple-page scan to FTP job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page.
File Name Enter a base file name.
Copy a document containing mixed paper sizes in a single copy job.
Specify whether a preview appears on the display for scan jobs.
Adjust the amount of background visible on a copy.
‑4 to 4
Specify the contrast of the scanned image.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4
Correct the slight skew in the scanned image.
Allow edge‑to‑edge scanning of the original document.
Scan edge to edge

Understanding the printer menus 215
1–5 Adjust the amount of sharpness on a scanned image.
Enable the user to specify “warm” or “coo”l outputs. “Cool” values generate a bluer output than the default while “warm” values generate a redder output than the default.
‑4 to 4
1–999 Specify a default number of copies for each print job.
Set a default paper source for all print jobs.
Tray [x] Multipurpose Feeder Manual Paper Manual Envelope
Stack the pages of a print job in sequence when printing multiple copies.
1,1,1 ‑ 2,2,2 1,2,3 ‑ 1,2,3
Specify whether prints are on one side or on both sides of the page.
1 sided 2 sided
Specify whether the printed outputs are stapled.
Specify whether prints have punched holes.
Specify the number of holes to be made on the prints.
2 holes 3 holes 4 holes
Define binding for duplexed pages in relation to the page orientation of the printed document.
Long Edge Short Edge

Understanding the printer menus 216
Print multiple pages on a single sheet of paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Specify the positioning of multiple‑page images.
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify the orientation of a multiple‑page document.
Print a border on each image in jobs that generate multiple page images.
Specify whether blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages
Specify the paper source for separator sheets.
Tray [x] Multipurpose Feeder
Specify whether blank pages are inserted in a print job.
Do Not Print Print

Understanding the printer menus 217
Set the default printer language.
PCL Emulation PS Emulation
Specify that print jobs be removed from the print queue if they require unavailable printer options or custom settings. They are stored in a separate print queue, so other jobs print normally. When the missing information or options are obtained, the stored jobs print.
Set the logical and physical printable area.
Normal Fit to Page Whole Page
Set the storage location for downloads.

Understanding the printer menus 218
Specify how the printer handles temporary downloads, such as fonts and macros stored in the RAM, when the printer receives a job that requires more memory than is available.
Specify the order in which held and confidential jobs are printed when Print All is selected.
Alphabetical Oldest First Newest First
Specify whether two‑sided (duplex) printing is set as the default for all print jobs.
1 sided 2 sided
Click File > Print, and then click Properties, Preferences, Options, or Setup. For Macintosh users:
Choose File > Print, and then adjust the settings from the Print dialog and pop‑up menus.
Define the way duplexed pages are bound and printed.
Long Edge Short Edge
1–999 Specify the default number of copies for each print job.
Specify whether blank pages are inserted in a print job.
Do Not Print Print

Understanding the printer menus 219
Stack the pages of a print job in sequence when printing multiple copies.
1,1,1 ‑ 2,2,2 1,2,3 ‑ 1,2,3
Specify whether blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages
Specify the paper source for separator sheets.
Tray [x] Multipurpose Feeder
Print multiple‑page images on one side of a paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Specify the positioning of multiple‑page images when using Paper Saver.
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify the orientation of a multiple‑page document.
Print a border when using Paper Saver.

Understanding the printer menus 220
Specify whether printed output is stapled.
Run Stapler Test Print a report that confirms that the staple finisher is functioning properly.
Specify whether holes will be created on printed outputs for the purpose of collecting the sheets in a binder or folder.
Specify the number of holes to be created on printed outputs for the purpose of collecting the sheets in a binder or folder.
2 holes 3 holes 4 holes
Offset pages at certain instances.
None Between Copies Between Jobs
Specifies the printed output resolution
600 dpi 1200 dpi 1200 Image Q 2400 Image Q 300 dpi

Understanding the printer menus 221
Adjusts pixels to print a sharper image.
Off Fonts Horizontally Vertically Both directions Isolated
1–10 Lightens or darkens the print
Enables a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts
Allows the user to print mid‑gray images
Adjusts brightness in color print jobs
‑6 to 6
0–5 Adjusts contrast in color print jobs

Understanding the printer menus 222
Set the scanner to create a log of the print jobs it receives.
Job Accounting Utilities Print and delete log files or export them to a flash drive.
Determine how often a log file is created.
Log Action at End of Frequency
Set how the scanner responds to the expiration of the frequency threshold.
None E‑mail Current Log E‑mail & Delete Current Log Post Current Log Post & Delete Current Log
Log Near Full Level
Specify the maximum size of the log file before the scanner executes the Log Action at Near Full.
Log Action at Near Full
Determine and set how the scanner responds when the scanner hard disk is nearly full.
None E‑mail Current Log E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post Current Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
Log Action at Full
Determine and set how the scanner responds when disk usage reaches the maximum limit (100MB).
None E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
URL to Post Logs Determine and set where the scanner posts job accounting logs.
E‑mail to Send Logs Specify the e‑mail address to which the scanner sends job accounting logs.

Understanding the printer menus 223
Log File Prefix Specify the prefix you want for the log file name.
Removes confidential and held jobs from the scanner hard disk
Confidential Held Not Restored All
Formats the flash memory
Delete Downloads on Disk
Removes downloads from the scanner hard disk, including all held jobs, buffered jobs, and parked jobs
Delete Now Do Not Delete
Activate Hex Trace Assists in isolating the source of a print job problem
Provides an estimate of the percentage coverage of toner on a page. The estimate is printed on a separate page at the end of each print job.

Understanding the printer menus 224
Print a page containing information on errors, including XML markup errors.
Scale page content to fit the selected paper size.
Print annotations in a PDF.
Do Not Print Print
Print a page containing the PostScript error.
Lock PS Startup Mode
Disable the SysStart file.
Establish the font search order.

Understanding the printer menus 225
Specify the set of fonts used by the Font Name menu.
Resident Disk Download Flash All
Identify a specific font and the option where it is stored.
Specify the symbol set for each font name.
Change the point size for scalable typographic fonts.
1.00–1008.00
Specify the font pitch for scalable monospaced fonts.
0.08–100
Specify the orientation of text and graphics on the page.

Understanding the printer menus 226
Specify the number of lines that print on each page.
Set the printer to print on A4‑size paper.
198 mm 203 mm
Specify whether the scanner automatically performs a carriage return (CR) after a line feed (LF) control command.
Auto CR after LF
Specify whether the scanner automatically performs a line feed (LF) after a carriage return (CR) control command.
Auto LF after CR
Configure the scanner to work with scanner software or programs that use different source assignments for trays and feeders.
Off None 0–199 Assign Tray [x]
Off None 0–199 Assign Manual Paper
Off None 0–199 Assign Manual Envelope

Understanding the printer menus 227
Display the factory default setting assigned to each tray or feeder.
MPF Default = 8 T1 Default = 1 T1 Default = 4 T1 Default = 5 T1 Default = 20 T1 Default = 21 Env Default = 6 MPaper Default = 2 MEnv Default = 3
Restore all tray and feeder assignments to the factory default settings.
Joanna MT Letter Gothic Lubalin Graph Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino StempelGaramond Taffy Times TimesNewRoman Univers Zapf Chancery NewSansMTCS NewSansMTCT New SansMTJA NewSansMTKO
Set the default font for HTML documents.
Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text Intl CG Times Intl Courier Intl Univers

Understanding the printer menus 228
1–255 pt Set the default font size for HTML documents.
1–400% Scale the default font for HTML documents.
Set the page orientation for HTML documents.
8–255 mm Set the page margin for HTML documents.
Specify whether to print backgrounds on HTML documents.
Do Not Print Print
Select the optimal paper size, scaling, and orientation.
Invert bitonal monochrome images.
Scale the image to fit the selected paper size.
Anchor Top Left Best Fit Anchor Center Fit Height/Width Fit Height Fit Width

Understanding the printer menus 229
Set the image orientation.
Portrait Landscape Reverse Portrait Reverse Landscape
The Help menu consists of a series of Help pages that are stored in the scanner as PDF files. They contain information about using the scanner and performing various tasks, including copying, scanning, and faxing.
English, French, German, and Spanish translations are stored in the scanner.
Other translations are available on the Lexmark Web site at www.lexmark.com.
Print All Guides Prints all the guides
Copy Guide Provides information about making copies and changing settings
Fax Guide Provides information about sending faxes using fax numbers, shortcut numbers, or the address book, and about changing settings
E‑mail Guide Provides information about sending e‑mails using addresses, shortcut numbers, or the address book, and about changing settings
FTP Guide Provides information about scanning documents directly to an FTP server using an FTP address, shortcut numbers, or the address book, and about changing settings
Print Defects Guide Provides help in resolving repeating defects in copies or prints
Information Guide Provides help in locating additional information
Supplies Guide Provides part numbers for ordering supplies
Use To · Orientation · Menu item Description

Saving money and the environment 230
Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impact on the environment. We design with the environment in mind, engineer our packaging to reduce materials, and provide collection and recycling programs. For more information, see:
By selecting certain printer settings or tasks, you may be able to reduce your printer's impact even further. This chapter outlines the settings and tasks that may yield a greater environmental benefit.
Studies show that as much as 80% of the carbon footprint of a printer is related to paper usage. You can significantly reduce your carbon footprint by using recycled paper and the following printing suggestions, such as printing on both sides of the paper and printing multiple pages on one side of a single sheet of paper.
For information on how you can quickly save paper and energy using one printer setting, see “Using Eco‑Mode” on page 231.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser printers. For more information on recycled papers that work well with your printer, see “Using recycled paper and other office papers” on page 86.
If your printer model supports two‑sided printing, then you can control whether print appears on one or two sides of the paper.
You can print up to 16 consecutive pages of a multiple‑page document onto one side of a single sheet of paper by setting multiple page printing (N‑Up) for the print job.

Saving money and the environment 231
Before printing or making multiple copies of a document:
Correctly set the paper type and size to avoid paper jams. For more information, see “Avoiding jams” on page 265.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > General Settings > Eco‑Mode > select a setting.
Off Use the factory default settings for all settings associated with Eco‑Mode. Off supports the performance specifications of the printer.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy and Paper modes.
3 Click Submit.
Enable Quiet Mode to reduce printer noise.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > General Settings > Quiet Mode > select a setting.
Use To

Saving money and the environment 232
On Reduce printer noise.
Off Use factory default settings.
3 Click Submit.
To save energy, decrease the number of minutes before the scanner and the printer enter Sleep mode.
Select from 1 to 120 minutes. The factory default setting is 45 minutes.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > General Settings > Timeouts.
3 In the Sleep Mode field, enter the number of minutes you want the scanner and the printer to wait before they enter Sleep mode.
4 Click Submit.
1 From the scanner home screen, navigate to:
> Settings > General Settings > Timeouts > Sleep Mode
2 In the Sleep Mode field, select the number of minutes you want the scanner and the printer to wait before they enter Sleep mode, and then touch Submit.
Use To

Saving money and the environment 233
To save energy, or if you have trouble reading your display, then adjust the brightness of the display.
Available settings range from 20–100. The factory default setting is 100.
1 Type the scanner IP address or host name in the address field of your Web browser.
If you do not know the IP address or host name of the scanner, then you can:
2 Click Settings > General Settings.
3 In the Screen Brightness field, enter the brightness percentage you want for the display.
4 Click Submit.
1 From the home screen, navigate to:
> Settings > General Settings
2 Touch the arrows until Screen Brightness appears, and then select a setting.
3 Touch Submit.
Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information, see:
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country or region from the list.
3 Follow the instructions on the computer screen.

Saving money and the environment 234
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark will recycle the box.
Lexmark Cartridge Collection Program diverts millions of Lexmark cartridges from landfills annually by making it both easy and free for Lexmark customers to return used cartridges to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. Boxes used to return the cartridges are also recycled.
To return Lexmark cartridges for reuse or recycling, follow the instructions that came with your printer or cartridge and use the prepaid shipping label. You can also do the following:
1 Go to www.lexmark.com/recycle.
2 From the Toner Cartridges section, select your country or region.
3 Follow the instructions on the computer screen.

Securing the printer 235
Statement of Volatility
Your scanner contains various types of memory that are capable of storing device and network settings, information from embedded solutions, and user data. The following are the types of memory and the types of data they store:
There are several circumstances where you may want to erase the contents of memory of devices installed in the scanner. A partial list includes:
In high‑security environments, it may be necessary to take additional steps to ensure that confidential data stored on the scanner hard disk cannot be accessed once the scanner—or its hard disk—is removed from your premises.
The volatile memory (RAM) installed in your scanner requires a power source to retain information. To erase the buffered data, simply turn off the scanner and the printer.

Securing the printer 236
1 Turn off the scanner.
2 Hold down and 6 MNO while turning the scanner on. Release the buttons only when the screen with the progress bar appears.
The scanner performs a power-on sequence, and then the Configuration menu appears. When the scanner is fully powered up, the touch screen displays a list of functions, instead of the standard home screen icons.
3 Touch Wipe All Settings.
The scanner will reboot several times during this process.
4 Touch Back > Exit Config Menu.
The scanner will power‑on reset, and then return to normal operating mode.
Configuring Disk Wiping lets you remove residual confidential material left by scan, print, copy, and fax jobs, by securely overwriting files that have been marked for deletion.
1 Turn off the scanner.
2 Hold down and 6 MNO while turning the scanner on. Release the buttons only when the screen with the progress bar appears.
The scanner performs a power-on sequence, and then the Configuration menu appears. When the scanner is fully powered up, the touch screen displays a list of functions, instead of the standard home screen icons.
4 Touch Yes to proceed with disk wiping. A status bar will indicate the progress of the disk wiping task.
5 Touch Back > Exit Config Menu.
The scanner will power‑on reset, and then return to normal operating mode.

Securing the printer 237
Enable hard disk encryption to prevent loss of sensitive data in the event the scanner or its hard disk is stolen.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Security > Disk Encryption.
3 From the Disk encryption menu, select Enable.
4 Click Submit.
1 Turn off the printer and the scanner.
2 Hold down 2 and 6 of the scanner while turning on both devices. Release the buttons only when the screen with the progress bar appears.
The scanner performs a power-on sequence, and then the Configuration menu appears. When the scanner is fully turned on, a list of functions appears on the scanner display.
3 Touch Disk Encryption > Enable.
4 Touch Yes to proceed with disk wiping.
5 Touch Back > Exit Config Menu.
The scanner performs a power‑on reset, and then returns to normal operating mode.

Securing the printer 238
In high-security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer cannot be accessed by unauthorized persons. For more information, visit the Lexmark security Web page.
You can also see the Embedded Web Server — Security: Administrator’s Guide for additional information:
1 Go to www.lexmark.com, and then navigate to Support & Downloads > select your printer.
2 Click the Manuals tab, and then select Embedded Web Server — Security: Administrator’s Guide.

Maintaining the scanner and the printer 239
Periodically, certain tasks are required to maintain optimum print quality.
1 Make sure that the printer is turned off and unplugged from the electrical outlet.
2 Remove paper from the standard bin and multipurpose feeder.
3 Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.
4 Dampen a clean, lint-free cloth with water, and use it to wipe the outside of the printer.
5 Make sure all areas of the printer are dry before sending a new print job.
1 Make sure the scanner is turned off and unplugged from the wall outlet.
2 Remove paper from the standard exit bin.
3 Dampen a clean, lint‑free cloth with water.
4 Wipe only the exterior of the scanner, including the exit tray.
5 Make sure the paper support and exit tray are dry before using the scanner.

Maintaining the scanner and the printer 240
Clean the scanner glass if you encounter print quality problems, such as streaks on copied or scanned images.
1 Slightly dampen a soft, lint-free cloth or paper towel with water.
2 Open the scanner cover.

1 White underside of the scanner cover
3 Wipe the scanner glass until it is clean and dry.
4 Wipe the white underside of the scanner cover until it is clean and dry.
5 Close the scanner cover.
1 Slightly dampen a soft, lint-free cloth or paper towel with water.
2 Open the ADF cover.

2 Scanner glass

Maintaining the scanner and the printer 241
3 Wipe the upper and lower ADF glass until they are clean and dry.

4 Close the ADF cover.
Clean the ADF parts periodically to ensure the ADF feeds paper properly. Residue on the ADF parts may cause scan quality issues and false paper jam messages.
When cleaning ADF parts, use the cleaning kit that came with the scanner.
1 Remove the cleaning kit from its container under the exit tray.

2 Unpack and unfold the cleaning cloth.


Maintaining the scanner and the printer 242
3 Open the ADF cover.
4 Using the cleaning cloth, wipe the rollers in the upper portion of the ADF until all residue is removed.


1 Two rollers that do not rotate freely
2 Six rollers that rotate freely

Maintaining the scanner and the printer 243
a To clean the rollers that do not rotate freely, push each roller inward, rotate it, then wipe it with the cleaning
cloth.


b To clean the rollers that rotate freely, wipe the rollers until all residue is removed.



Maintaining the scanner and the printer 244
5 Using the cleaning cloth, wipe the rollers in the lower portion of the ADF until all residue is removed.
1 Six rollers that do not rotate freely
2 Six rollers that rotate freely
a To clean the rollers that do not rotate freely, manually rotate the last roller toward the ADF entrance. This will
reposition the other rollers that do not rotate freely.


Maintaining the scanner and the printer 245
b To clean the rollers that rotate freely, wipe the rollers until all residue is removed.

6 Wait for 3 minutes to let the rollers dry.
Clean the scanner touch screen regularly to remove fingerprints and smudges.
1 Make sure the scanner is turned off and unplugged from the wall outlet.
2 Remove the cleaning kit from the compartment under the exit tray.
3 Unpack the cleaning kit.
4 Wipe the touch screen with the wet cloth first, and then with the dry cloth.

Maintaining the scanner and the printer 246
1 Pull out the hole punch box.

2 Empty the container.

3 Insert the emptied hole punch box back into the finisher until it clicks into place.
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:
A message appears on the scanner display when a replacement supply item is needed or when maintenance is required.
From the home screen, touch Status/Supplies > View Supplies.

Maintaining the scanner and the printer 247
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Device Status > More Details.
The estimated number of remaining pages is based on the recent printing history of the printer. Its accuracy may vary significantly and is dependent on many factors, such as actual document content, print quality settings, and other printer settings.
The accuracy of the estimated number of remaining pages may decrease when the actual printing consumption is different from the historical printing consumption. Consider the variable level of accuracy before purchasing or replacing supplies based on the estimate. Until an adequate print history is obtained on the printer, initial estimates assume future supplies consumption based on the International Organization for Standardization* test methods and page content.
* Average continuous black declared cartridge yield in accordance with ISO/IEC 19752.
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, go to the Lexmark Web Site at www.lexmark.com or contact the place where you purchased the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. Use of third-party supplies or parts can affect warranty coverage. Damage caused by the use of third-party supplies or parts is not covered by the warranty. All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.
Clean the ADF parts periodically to maintain the optimal performance of the device.

Maintaining the scanner and the printer 248
Part name Part number
ADF feed roller cleaning cloth 16J0900
When Replace separator pad appears on the display, order a separator pad.
Part name Part number
Item Return Program cartridge
For the United States and Canada
High Yield Toner Cartridge 521H
Extra High Yield Toner Cartridge 521X*
For the European Union, European Economic Area , and Switzerland
High Yield Toner Cartridge 522H
Extra High Yield Toner Cartridge 522X*
For the Asia Pacific Region (includes Australia and New Zealand)
High Yield Toner Cartridge 523H
Extra High Yield Toner Cartridge 523X*
For Latin America (includes Puerto Rico and Mexico)
High Yield Toner Cartridge 524H
Extra High Yield Toner Cartridge 524X*
* This toner cartridge is supported only in the MS711, MS811n, MS811dn, and MS812dn printer models.
For more information on countries located in a region, visit www.lexmark.com/regions.

Maintaining the scanner and the printer 249
Item Return Program cartridge
For Africa, Middle East, Central Eastern Europe, and Commonwealth of Independent States
High Yield Toner Cartridge 525H
Extra High Yield Toner Cartridge 525X*
* This toner cartridge is supported only in the MS711, MS811n, MS811dn, and MS812dn printer models.
For more information on countries located in a region, visit www.lexmark.com/regions.
High Yield Toner Cartridge 520HA1
Extra High Yield Toner Cartridge 520XA2
1 This cartridge is supported only in the MS710, MS810n, and MS810dn printer models.
2 This cartridge is supported only in the MS711, MS811n, MS811dn, and MS812dn printer models.
To identify the supported fuser type, view the label on the fuser. Do either of the following:
Lexmark Return Program fuser maintenance kits and part numbers for MS810n, MS810dn, MS811, and MS812dn
Fuser maintenance kit type Part number

Maintaining the scanner and the printer 250

Lexmark regular fuser maintenance kits and part numbers for MS810n, MS810dn, MS811, and MS812dn


Fuser maintenance kit type Part number
Extremely low print coverage for extended periods of time may cause imaging unit parts to fail prior to exhaustion of toner.
For more information on replacing the imaging unit, see the instruction sheet that came with the supply.
Part name Lexmark Return Program Regular
Imaging unit 520Z 520ZA
Part name Part number
roller kit 40X7706 · Staple cartridges 25A0013

Maintaining the scanner and the printer 251
1 Turn the printer off, and then open the ADF cover.
2 Remove the separator pad.



3 Unpack the new separator pad, and then install it in the scanner.

Maintaining the scanner and the printer 252
4 Close the ADF cover.
5 Dispose of the old separator pad.
1 Lift the front cover, and then pull down the multipurpose feeder door.


Maintaining the scanner and the printer 253
2 Pull the cartridge out of the printer using the handle.

3 Unpack the new toner cartridge, then remove the packing material, and then shake the cartridge to redistribute the toner.

4 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.


Maintaining the scanner and the printer 254
5 Close the multipurpose feeder door and the front cover.
1 Lift the front cover, and then pull down the multipurpose feeder door.

Maintaining the scanner and the printer 255
2 Pull the cartridge out of the printer using the handle.
3 Pull the imaging unit out of the printer using the handle.


4 Unpack the new imaging unit, and then remove all packing materials.


Maintaining the scanner and the printer 256
5 Shake the new imaging unit.

6 Insert the imaging unit into the printer by aligning the arrows on the side rails of the imaging unit with the arrows on the side rails inside the printer.

7 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.

Maintaining the scanner and the printer 257
8 Close the multipurpose feeder door and the front cover.
1 Open the stapler door.

2 Pull down the latch of the staple cartridge holder, and then pull the holder out of the finisher.



Maintaining the scanner and the printer 258
3 Squeeze both sides of the empty staple case with your fingers, and then remove the staple case from the cartridge.

4 Insert the front side of the new staple case into the staple cartridge, and then push the rear side into the cartridge.

5 Push the staple cartridge into the finisher until it clicks into place.
6 Close the stapler door.

Maintaining the scanner and the printer 259
The scanner can be safely moved to another location by following these precautions:
> Lock Scanner Head 2 Turn off the scanner and printer. 3 Lock the scan bar.
When shipping the scanner, use the original packaging or call the place of purchase for a relocation kit.

Maintaining the scanner and the printer 260
– Make sure to remove the topmost finisher first. – To remove the finisher, hold the finisher on both sides, and then lift the latches to unlock the finisher.



Maintaining the scanner and the printer 261


The printer and its hardware options can be safely moved to another location by following these precautions:
When shipping the printer, use the original packaging or call the place of purchase for a relocation kit.

Managing the scanner and the printer 262
Finding advanced networking and administrator information
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server — Security: Administrator's Guide on the Lexmark support Web site at http://support.lexmark.com.
1 Access the Embedded Web Server associated with your scanner.
Type the scanner IP address or host name in the address field of your Web browser.
If you do not know the IP address of host name of the scanner, then you can:
2 Check the virtual display that appears in the top left corner of the screen.
The virtual display works as an actual display would work on a scanner control panel.
Configure the scanner to send your e‑mail alerts when the supplies are getting low or when the paper needs to be changed or added, or when there is a paper jam.
1 Type the scanner IP address or host name in the address field of your Web browser.
If you do not know the IP address or host name of the scanner, then you can:
2 Click Settings > E‑mail Alert Setup.
3 Select the items for notification, and type the e‑mail addresses.
4 Click Submit.
You can view some reports from the Embedded Web Server. These reports are useful for assessing the status of the printer, network, and supplies.
To view reports from a network printer:
1 Type the scanner IP address in the address field of your Web browser.

Managing the scanner and the printer 263
If you do not know the IP address or host name of the scanner, then you can:
2 Click Reports, and then click the type of report you want to view.
You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
1 Open a Web browser, and then type the scanner IP address in the address field.
2 Click Settings > Print Settings > Supply Notifications.
3 From the drop‑down menu for each supply, select one of the following notification options:
Off The normal printer behavior for all supplies occurs.
E‑mail Only The printer generates an e‑mail when the supply condition is reached. The status of the supply appears on the menus page and status page.
Continuable Stop1 The printer stops processing jobs when the supply condition is reached, and the user needs to press a button to continue printing.
Non Continuable Stop1,2 The printer stops processing jobs when the supply condition is reached. The supply must be replaced to continue printing.
1 The printer generates an e-mail about the status of the supply when supply notification is enabled.
2 The printer stops when some supplies become empty to prevent damage.
4 Click Submit.
Notification Description

Managing the scanner and the printer 264
If you want to retain a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings.
From the home screen, navigate to:
> Settings > General Settings > Factory Defaults > Restore Now > Submit

Carefully select paper and specialty media and load them properly to avoid most jams. If jams occur, then follow the steps outlined in this chapter.

Clearing jams 265



– If the bin extender is shorter than the size of the paper you are printing on, then the paper causes a jam in
the mailbox bin. For example, if you are printing on a legal-size paper and the bin extender is set to letter- size, then a jam occurs. – If the bin extender is longer than the size of the paper you are printing on, then the edges become uneven
and the paper is not stacked properly. For example, if you are printing on a letter-size paper and the bin extender is set to legal-size, then the paper does not stack properly.
Clearing jams 266



When a jam occurs, a message indicating the jam location and information to clear the jam appears on the printer display. Open the doors, covers, and trays indicated on the display to remove the jam.
Clearing jams 267


3 4 5 6



Jam location Printer message What to do
1 Staple finisher [x]‑page jam, remove paper, open stapler door. Leave paper in bin. [455–457]
Remove paper from the stapler bin, open the stapler door, then remove the staple cartridge, and then remove the jammed staples.
2 Standard bin [x]‑page jam, remove standard bin jam. [203]
Remove jammed paper from the standard bin.
Clearing jams 268

Jam location Printer message What to do
3 Inside the printer [x]‑page jam, lift front cover to remove cartridge. [200– 201]
Open the front cover and the multipurpose feeder, then remove the toner cartridge and the imaging unit, and then remove the jammed paper.
4 Multipurpose feeder [x]‑page jam, clear manual feeder. [250]
Remove all paper from the multipurpose feeder, and then remove the jammed paper.
5 Duplex area [x]‑page jam, remove tray 1 to clear duplex. [235–239]
Pull out tray 1 completely, then push down the front duplex flap, and then remove the jammed paper.
6 Trays [x]‑page jam, open tray [x]. [24x]
Pull out the indicated tray, and then remove the jammed paper.
7 Output expander [x]‑page jam, remove paper, open expander rear door. Leave paper in bin. [41y.xx]
Open the rear door of the output expander, and then remove the jammed paper.
8 Upper rear door [x]‑page jam, open upper rear door. [202]
Open the rear door of the printer, and then remove the jammed paper.
9 Upper door and rear duplex area
[x]‑page jam, open upper and lower rear door. [231–234]
Open the rear door of the printer and the rear duplex area, and then remove the jammed paper.
10 Mailbox [x]‑page jam, remove paper, open mailbox rear door. Leave paper in bin. [43y.xx]
Open the rear door of the mailbox, and then remove the jammed paper.
11 Staple finisher rear door [x]‑page jam, remove paper, open finisher rear door. Leave paper in bin. [451]
Open the rear door of the staple finisher, and then remove the jammed paper.
[x]‑page jam, open automatic feeder top cover. [28y.xx]
12 Automatic document feeder (ADF)
Remove all paper from the ADF tray, and then remove the jammed paper.
Clearing jams 269
![Page 270 of the Lexmark MX6500E user manual — [x] ‑ page jam, lift front cover to remove cartridge. [200–201]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-270.webp?w=400)
1 Lift the front cover, and then pull down the multipurpose feeder door.
2 Lift the green handle, and then pull out the toner cartridge from the printer.
3 Place the cartridge aside.
4 Lift the green handle, and then pull out the imaging unit from the printer.
Clearing jams 270
![Page 271 of the Lexmark MX6500E user manual — [x]-page jam, lift front cover to remove cartridge. [200–201]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-271.webp?w=400)
5 Place the imaging unit aside on a flat, smooth surface.
6 Pull the jammed paper gently to the right, and then remove it from the printer.
![Lexmark MX6500E — [x]-page jam, lift front cover to remove cartridge. [200–201] diagram (page 271)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-138.webp)
7 Install the imaging unit.
8 Insert the cartridge into the printer, and then push the green handle back into place.
Clearing jams 271
![Page 272 of the Lexmark MX6500E user manual — [x] ‑ page jam, open upper rear door. [202]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-272.webp?w=400)
9 Close the multipurpose feeder door and the front cover.
10 From the scanner control panel, touch Done to clear the message and continue printing.
1 Pull down the rear door.
![Lexmark MX6500E — [x] ‑ page jam, open upper rear door. [202] diagram (page 272)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-139.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 272
![Page 273 of the Lexmark MX6500E user manual — [x] ‑ page jam, open upper and lower rear door. [231–234]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-273.webp?w=400)
3 Close the rear door.
4 From the scanner control panel, touch Done to clear the message and continue printing.
1 Pull down the rear door.
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 273
![Page 274 of the Lexmark MX6500E user manual — [x]-page jam, open upper and lower rear door. [231–234]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-274.webp?w=400)
3 Close the rear door.
4 Push the back of the standard tray.
![Lexmark MX6500E — [x]-page jam, open upper and lower rear door. [231–234] diagram (page 274)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-140.webp)
5 Press down the rear duplex flap, then firmly grasp the jammed paper, and then gently pull out the paper.
Clearing jams 274
![Page 275 of the Lexmark MX6500E user manual — [x] ‑ page jam, remove tray 1 to clear duplex. [235–239]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-275.webp?w=400)
![Lexmark MX6500E — [x]-page jam, remove standard bin jam. [203] diagram (page 275)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-141.webp)
![Lexmark MX6500E — [x]-page jam, remove standard bin jam. [203] diagram (page 275)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-142.webp)
6 Insert the standard tray.
7 From the scanner control panel, touch Done to clear the message and continue printing.
1 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark MX6500E — [x] ‑ page jam, remove standard bin jam. [203] diagram (page 275)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-143.webp)
2 From the scanner control panel, touch Done to clear the message and continue printing.
1 Pull out the tray.
Clearing jams 275
![Page 276 of the Lexmark MX6500E user manual — [x]-page jam, remove standard bin jam. [203]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-276.webp?w=400)
![Lexmark MX6500E — [x]-page jam, remove standard bin jam. [203] diagram (page 276)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-144.webp)
![Lexmark MX6500E — [x]-page jam, remove standard bin jam. [203] diagram (page 276)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-145.webp)
2 Push down the front duplex flap, then firmly grasp the jammed paper, and then gently pull the paper to the right and out of the printer.
![Lexmark MX6500E — [x]-page jam, remove standard bin jam. [203] diagram (page 276)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-146.webp)
3 Insert the tray.
4 From the scanner control panel, touch Done to clear the message and continue printing.
Clearing jams 276
![Page 277 of the Lexmark MX6500E user manual — [x] ‑ page jam, open tray [x]. [24x]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-277.webp?w=400)
1 Check which tray is indicated on the printer display, and then pull the tray.
![Lexmark MX6500E — [x] ‑ page jam, open tray [x]. [24x] diagram (page 277)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-147.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
3 Insert the tray.
4 From the scanner control panel, touch Done to clear the message and continue printing.
Clearing jams 277
![Page 278 of the Lexmark MX6500E user manual — [x] ‑ page jam, clear manual feeder. [250]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-278.webp?w=400)
1 From the multipurpose feeder, firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark MX6500E — [x] ‑ page jam, clear manual feeder. [250] diagram (page 278)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-148.webp)
2 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.
![Lexmark MX6500E — [x] ‑ page jam, clear manual feeder. [250] diagram (page 278)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/fig-278-1.webp)
3 Reload paper into the multipurpose feeder.
Clearing jams 278
![Page 279 of the Lexmark MX6500E user manual — [x]-page jam, remove paper, open mailbox rear door. Leave paper in bin. [41y.xx]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-279.webp?w=400)
4 Slide the paper guide until it rests lightly against the edge of the paper.
![Lexmark MX6500E — [x]-page jam, remove paper, open mailbox rear door. Leave paper in bin. [41y.xx] diagram (page 279)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-149.webp)
![Lexmark MX6500E — [x]-page jam, remove paper, open mailbox rear door. Leave paper in bin. [41y.xx] diagram (page 279)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-150.webp)
5 From the scanner control panel, touch Done to clear the message and continue printing.
[x]‑page jam, remove paper, open mailbox rear door. Leave paper in bin. [41y.xx]
1 Open the mailbox rear door.
![Lexmark MX6500E — [x]-page jam, remove paper, open mailbox rear door. Leave paper in bin. [41y.xx] diagram (page 279)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-151.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 279
![Page 280 of the Lexmark MX6500E user manual — [x]-page jam, remove paper, open mailbox rear door. Leave paper in bin. [41y.xx]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-280.webp?w=400)
3 Close the mailbox rear door.
4 If the jam is in the mailbox bin, then firmly grasp the jammed paper, and then gently pull it out.
![Lexmark MX6500E — [x]-page jam, remove paper, open mailbox rear door. Leave paper in bin. [41y.xx] diagram (page 280)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-152.webp)
Clearing jams 280
![Page 281 of the Lexmark MX6500E user manual — [x]-page jam, remove paper, open finisher rear door. Leave paper in bin. [451]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-281.webp?w=400)
5 From the scanner control panel, touch Done to clear the message and continue printing.
[x]‑page jam, remove paper, open finisher rear door. Leave paper in bin. [451]
1 Open the staple finisher rear door.
![Lexmark MX6500E — [x]-page jam, remove paper, open finisher rear door. Leave paper in bin. [451] diagram (page 281)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-153.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 281
![Page 282 of the Lexmark MX6500E user manual — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-282.webp?w=400)
3 Close the staple finisher rear door.
4 From the scanner control panel, touch Done to clear the message and continue printing.
[x]‑page jam, remove paper, open stapler door. Leave paper in bin. [455–457]
1 From the stapler bin, firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark MX6500E — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457] diagram (page 282)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-154.webp)
Clearing jams 282
![Page 283 of the Lexmark MX6500E user manual — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-283.webp?w=400)
2 Open the stapler door.
3 Pull down the latch of the staple cartridge holder, and then pull out the holder from the printer.
4 Use the metal tab to lift the staple guard, and then remove any loose staples.
![Lexmark MX6500E — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457] diagram (page 283)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-155.webp)
Clearing jams 283
![Page 284 of the Lexmark MX6500E user manual — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-284.webp?w=400)
5 Press down the staple guard until it clicks into place.
![Lexmark MX6500E — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457] diagram (page 284)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-156.webp)
6 Press the staples against the metal bracket.
![Lexmark MX6500E — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457] diagram (page 284)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-157.webp)
Clearing jams 284
![Page 285 of the Lexmark MX6500E user manual — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-285.webp?w=400)
![Lexmark MX6500E — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457] diagram (page 285)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-158.webp)
7 Push the cartridge holder firmly back into the stapler unit until the cartridge holder clicks into place.
8 Close the stapler door.
9 From the scanner control panel, touch Done to clear the message and continue printing.
Clearing jams 285
![Page 286 of the Lexmark MX6500E user manual — [x]-page jam, remove paper, open expander rear door. Leave paper in bin. [43y.xx]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-286.webp?w=400)
[x]‑page jam, remove paper, open expander rear door. Leave paper in bin. [43y.xx]
1 Open the output expander rear door.
![Lexmark MX6500E — [x]-page jam, remove paper, open expander rear door. Leave paper in bin. [43y.xx] diagram (page 286)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-159.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
3 Close the output expander rear door.
4 From the scanner control panel, touch Done to clear the message and continue printing.
Clearing jams 286
![Page 287 of the Lexmark MX6500E user manual — [x] ‑ page jam, open automatic feeder top cover [28y.xx]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-287.webp?w=400)
1 Remove all original documents from the ADF tray.
2 Open the ADF cover.
![Lexmark MX6500E — [x] ‑ page jam, open automatic feeder top cover [28y.xx] diagram (page 287)](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/rimg-160.webp)
3 Firmly grasp the jammed paper on each side, and then gently pull it out.
4 Close the ADF cover.
5 Straighten the edges of the original documents, then load the documents into the ADF, and then adjust the paper guides.
6 From the scanner control panel, touch Done to clear the message and continue printing.
Clearing jams 287
![Page 288 of the Lexmark MX6500E user manual — Cartridge low [88.xy]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-288.webp?w=400)
For information on connecting the scanner and the printer, see “Connecting the scanner and the printer” on page 29.
The indicator light blinks red until you set up fax and e‑mail. To disable the blinking light, follow these steps:
1 From the home screen, navigate to:
Menus > Settings > General Settings
2 Touch the arrows next to Run initial setup, and then touch Yes > Submit.
3 Turn the scanner off, and then turn the scanner back on.
4 From the scanner control panel, touch your language.
5 Touch your country or region, and then touch Continue.
6 Select your time zone, and then touch Continue.
7 Touch Fax and E‑mail to clear the icons, and then touch Continue.
1 Check if the toner cartridge and imaging unit are both MICR (Magnetic Imaging Content Recording) or non-MICR supplies.
2 Change the toner cartridge or imaging unit so that both are MICR or non‑MICR supplies.
You may need to order a replacement toner cartridge. If necessary, touch Continue on the scanner control panel to clear the message and continue printing.
Troubleshooting 288
![Page 289 of the Lexmark MX6500E user manual — Change [paper source] to [paper type] [paper size] load [orientation]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-289.webp?w=400)
If necessary, touch Continue on the scanner control panel to clear the message and continue printing.
You may need to replace the toner cartridge very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, touch Continue on the scanner control panel to clear the message and continue printing.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 289

Try one or more of the following:
If the error occurs a second time, then:
1 Turn off the printer and the scanner. 2 Unplug the power cord from the electrical outlet. 3 Remove the indicated tray. 4 Reattach the tray. 5 Connect the power cord to a properly grounded electrical outlet. 6 Turn on the printer and the scanner.
If the error occurs again, then:
1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Remove the tray. 4 Contact customer support. • From the scanner control panel, touch Continue to clear the message and resume the job.
The toner cartridge is missing or not installed properly. Insert the cartridge, and then close all doors and covers.
Close the side door of the finisher.
Try one or more of the following:
Close the front door of the printer.
Troubleshooting 290

Close the printer top access cover to clear the message.
Try one or more of the following:
Held jobs are invalidated because of the following possible changes in the scanner:
From the scanner control panel, touch Continue to clear the message.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 291

From the scanner control panel, touch Format disk to format the scanner hard disk and to clear the message.
Disk near full. Securely clearing disk space.
Try one or more of the following:
1 Empty the hole punch box.
For instructions on emptying the hole punch box, touch More Information from the scanner control panel.
2 Reinsert the hole punch box into the finisher, and then touch Continue to clear the message.
Error reading USB drive. Remove USB.
An unsupported USB device is inserted. Remove the USB device, and then insert a supported one.
Error reading USB hub. Remove hub.
An unsupported USB hub has been inserted. Remove the USB hub, and then install a supported one.
From the scanner control panel, touch Continue to clear the message.
Fax partition inoperative. Contact system administrator.
Try one or more of the following:
Fax server 'To Format' not set up. Contact system administrator.
Try one or more of the following:
Troubleshooting 292
![Page 293 of the Lexmark MX6500E user manual — Incompatible tray [x] [59]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-293.webp?w=400)
Fax Station Name not set up. Contact system administrator.
Try either of the following:
Fax Station Number not set up. Contact system administrator.
Try one or more of the following:
You may need to order a replacement imaging unit. If necessary, select Continue on the scanner control panel to clear the message and continue printing.
If necessary, touch Continue on the scanner control panel to clear the message and continue printing.
You may need to replace the imaging unit very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, touch Continue on the scanner control panel to clear the message and continue printing.
Try one or more of the following:
Try one or more of the following:
Troubleshooting 293
![Page 294 of the Lexmark MX6500E user manual — Install bin [x]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-294.webp?w=400)
Try one or more of the following:
Insert the hole punch box into the finisher, and then touch Continue to clear the message.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 294
![Page 295 of the Lexmark MX6500E user manual — Insufficient memory, some held jobs will not be restored [37]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-295.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Install additional scanner memory or touch Continue to disable Resource Save, to clear the message, and to continue printing.
From the scanner control panel, touch Continue to clear the message.
Try one or more of the following:
Troubleshooting 295
![Page 296 of the Lexmark MX6500E user manual — Load [paper source] with [paper size] [paper orientation]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-296.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 296

Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 297
![Page 298 of the Lexmark MX6500E user manual — Network [x] software error [54]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-298.webp?w=400)
You may need to order a maintenance kit. For more information, visit the Lexmark Web site at http://support.lexmark.com or contact customer support, and then report the message. If necessary, touch Continue to clear the message and continue printing.
For more information, visit the Lexmark Web site at http://support.lexmark.com or contact customer support, and then report the message. If necessary, touch Continue to clear the message and continue printing.
You may need to replace the maintenance kit very soon. For more information, visit the Lexmark Web site at http://support.lexmark.com or contact customer support, and then report the message. If necessary, touch Continue to clear the message and continue printing.
Try one or more of the following:
1 From the scanner control panel, touch Continue to clear the message and cancel the fax job.
No analog phone line connected to modem, fax is disabled.
Connect the printer to an analog phone line.
Try one or more of the following:
Troubleshooting 298
![Page 299 of the Lexmark MX6500E user manual — Parallel port [x] disabled [56]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-299.webp?w=400)
The printer has detected a non‑Lexmark supply or part installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components.
All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or associated components.
To accept any and all of these risks, and to proceed with the use of non-genuine supplies or parts in your printer, touch and hold and the # on the scanner control panel simultaneously for 15 seconds to clear the message and continue printing.
If you do not want to accept these risks, then remove the third-party supply or part from your printer, and then install a genuine Lexmark supply or part.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Network/Ports > Parallel [x] > Parallel Buffer > Auto
Troubleshooting 299
![Page 300 of the Lexmark MX6500E user manual — Reattach bins [x] – [y]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-300.webp?w=400)
Printer had to restart. Last job may be incomplete.
From the scanner control panel, touch Continue to clear the message and continue printing.
For more information, visit http://support.lexmark.com or contact customer support.
Try one or more of the following:
Try one or more of the following:
Troubleshooting 300

5 Connect the power cord of the printer to a properly grounded electrical outlet. 6 Turn on the printer and the scanner.
From the scanner control panel, touch Continue to clear the message and print without using the indicated bins.
Try one or more of the following:
For information on installing the cartridge, see the “Replacing supplies” section of the User’s Guide. • If the toner cartridge is installed, then remove the unresponsive toner cartridge, and then reinstall it.
Try one or more of the following:
For more information on installing the fuser, see the instruction sheet that came with the part.
Try one or more of the following:
For information on installing the imaging unit, see the “Replacing supplies” section of the User’s Guide. • If the imaging unit is installed, then remove the unresponsive imaging unit, and then reinstall it.
Remove and replace the defective printer hard disk.
Remove any remaining packaging material from the specified location.
Remove the paper from all of the bins. The printer automatically senses paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Troubleshooting 301

Remove the paper from the specified bin. The printer automatically senses paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Remove paper from the specified bin. The printer automatically detects paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Remove the paper stack from the standard bin.
Replace all originals if restarting job.
Try one or more of the following:
Replace the toner cartridge to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Install a toner cartridge that matches the region number of the printer. x indicates the value of the printer region. y indicates the value of the cartridge region. x and y can have the following values:
1 United States, Canada
2 European Economic Area (EEA), Switzerland
3 Asia Pacific, Australia, New Zealand
![Page 303 of the Lexmark MX6500E user manual — Replace maintenance kit, 0 estimated pages remain [80.xy]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-303.webp?w=400)
5 Africa, Middle East, rest of Europe
Replace the imaging unit to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Replace jammed originals if restarting job.
Try one or more of the following:
Replace last scanned page and jammed originals if restarting job.
Try one or more of the following:
Contact customer support at http://support.lexmark.com or your service representative, and then report the message. The printer is scheduled for maintenance.
Troubleshooting 303 · Region number Region · 9 Invalid

1 Install the missing fuser. For more information, see the instruction sheet that came with the replacement part.
2 From the scanner control panel, touch Continue to clear the message.
Try one or more of the following:
Try one or more of the following:
Remove the toner cartridge, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Remove the fuser, and then install a supported one. For more information, see the instruction sheet that came with the part.
Remove the imaging unit, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Try one or more of the following:
Troubleshooting 304
![Page 305 of the Lexmark MX6500E user manual — Scanner jam, remove jammed originals from the scanner [2yy.xx]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-305.webp?w=400)
Try one or more of the following:
The scan job exceeds the maximum number of pages. Touch Cancel job to clear the message and cancel the scan job.
Close the ADF cover.
Print without the scanner, or contact your system support person.
Try one or more of the following:
Remove the jammed paper from the scanner.
Remove the jammed paper from the scanner.
Troubleshooting 305

1 Unlock the scan bar.
2 Touch Continue to clear the message and continue scanning.
Contact customer support, and then report the message. The printer is scheduled for maintenance.
Try one or more of the following:
Try one or more of the following:
From the scanner control panel, touch Continue to delete the indicated job.
Troubleshooting 306
![Page 307 of the Lexmark MX6500E user manual — Too many disks installed [58]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-307.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Network/Ports > USB Buffer > Auto
The scanner discards any data received through the USB port.
Do either of the following:
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra bins.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra printer hard disks.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Troubleshooting 307
![Page 308 of the Lexmark MX6500E user manual — Unsupported option in slot [x] [55]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-308.webp?w=400)
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra flash memory.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra trays.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Replace with a supported paper size.
Try one or more of the following:
The camera mode does not support PictBridge.
Unplug the camera, change the mode and plug the camera back into the printer.
An unsupported disk has been inserted. Remove the unsupported disk, and then install a supported one.
1 Turn off the scanner.
2 Unplug the power cord from the electrical outlet.
3 Remove the unsupported option card from the scanner controller board, and then replace it with a supported card.
Troubleshooting 308

4 Connect the power cord to a properly grounded electrical outlet.
5 Turn on the scanner.
From the scanner control panel, touch Continue to clear the message.
Weblink server not set up. Contact system administrator.
From the scanner control panel, touch Continue to clear the message.
Go to step 2. Turn on the printer.
Make sure the printer is turned on.
Is the printer turned on?
Press the Sleep button to wake the printer from Sleep mode.
Go to step 3.
Check if the printer is in Sleep mode.
Is the printer in Sleep mode?
Go to step 4. Plug one end of the power cord into the printer and the other to a properly grounded electrical outlet.
Check if one end of the power cord is plugged into the printer and the other to a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
![Page 310 of the Lexmark MX6500E user manual — USB port [x] disabled [56]](/cdn/reader/00/00902ec94dffaee076cdc8c8f02afcf877b5ae55085f2ae8a333eb1b35474b4d/images/page-310.webp?w=400)
Unplug the other electrical equipment, and then turn on the printer. If the printer does not work, then reconnect the other electrical equipment.
Go to step 5.
Check other electrical equipment plugged into the electrical outlet.
Do the other electrical equipment work?
Step 5 Check if the cables connecting the printer and the computer are inserted in the correct ports.
Go to step 6. Make sure to match the following:
Are the cables inserted in the correct ports?
Turn on the switch or reset the breaker.
Go to step 7.
Make sure the electrical outlet is not turned off by a switch or breaker.
Is the electrical outlet turned off by a switch or breaker?
Connect the printer power cord directly to a properly grounded electrical outlet.
Go to step 8.
Check if the printer is plugged into any surge protectors, uninterruptible power supplies, or extension cords.
Is the printer plugged into any surge protectors, uninterruptible power supplies, or extension cords?
Go to step 9. Connect the printer cable securely to the printer and the computer, print server, option, or other network device.
Check if one end of the printer cable is plugged into a port on the printer and the other to the computer, print server, option, or other network device.
Is the printer cable securely attached to the printer and the computer, print server, option, or other network device?
Go to step 10. Turn off the printer, remove all packing materials, then reinstall the hardware options, and then turn on the printer.
Make sure to install all hardware options properly and remove any packing material.
Are all hardware options properly installed and all packing material removed?
Go to step 11. Use correct printer driver settings.
Check if you have selected the correct port settings in the printer driver.
Are the port settings correct?

Go to step 12. Install the correct printer driver.
Check the installed printer driver.
Is the correct printer driver installed?
The problem is solved. Contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn it back on.
Is the printer working?
The problem is solved. Go to step 2.
Press the Sleep button on the scanner control panel.
Does Ready appear on the scanner display?
The problem is solved. Turn off the scanner, and then contact customer support.
Turn off the scanner, then wait for about 10 seconds, and then turn it back on.
Do Please wait and Ready appear on the scanner display?
Step 1 Turn off the scanner, then wait for about 10 seconds, and then turn it back on.
The problem is solved. Go to step 2.
Does the internal option operate correctly?
Step 2 Check if the internal option is properly installed in the controller board.
Go to step 3. Connect the internal option to the controller board.
a Turn off the scanner using the power switch, and then unplug the
power cord from the electrical outlet. b Make sure the internal option is installed in the appropriate connector
in the controller board. c Connect the power cord to the scanner, then to a properly grounded
electrical outlet, and then turn on the scanner.
Is the internal option properly installed in the controller board?

Go to step 4. Reinstall the internal option.
Print a menu settings page, and then check to see if the internal option is listed in the Installed Features list.
Is the USB or parallel interface card listed in the Installed Features list?
The problem is solved. Contact customer support.
a Check if the internal option is selected.
It may be necessary to manually add the internal option in the printer driver to make it available for print jobs. For more information, see “Adding available options in the print driver” on page 56. b Resend the print job.
Does the internal option operate correctly?
Go to step 2. Check if the internal print server is supported by the printer.
Reinstall the internal print server.
a Remove, and then install the internal print server. For more
information, see “Installing an Internal Solutions Port” on page 38. b Print a menu settings page, and then check if the internal print server
is listed in the Installed Features list.
Is the internal print server listed in the Installed Features list?
The problem is solved. Contact customer support.
Check the cable and the internal print server connection.
Use the correct cable, and then check if it is securely connected to the internal print server.
Does the internal print server operate correctly?
Go to step 2. Check if you have a supported ISP.
Make sure the Internal Solutions Port (ISP) is installed.
a Install the ISP. For more information, see “Installing an Internal
Solutions Port” on page 38. b Print a menu settings page, and then check if the ISP is listed in the
Installed Features list.
Is the ISP listed in the Installed Features list?

The problem is solved. Contact customer support.
Check the cable and the ISP connection.
a Use the correct cable, and then make sure it is securely connected to
the ISP. b Check if the ISP solution interface cable is securely connected into the
receptacle of the controller board.
Does the Internal Solutions Port operate correctly?
The problem is solved. Go to step 2.
a Pull out the tray, and then do one or more of the following:
Is the tray working?
The problem is solved. Go to step 3.
a Turn off the printer, then wait about 10 seconds, and then turn the
printer back on. b Resend the print job.
Is the tray working?
Go to step 4. Reinstall the tray. For more information, see the setup documentation that came with the tray.
Check if the tray is installed and recognized by the printer.
Print a menu settings page, and then check if the tray is listed in the Installed Features list.
Is the tray listed in the menu settings page?

The problem is solved. Contact customer support.
Check if the tray is available in the printer driver.
Is the tray available in the printer driver?
Go to step 2. Check if you have a supported USB or parallel interface card.
Make sure the USB or the parallel interface card is installed.
a Install the USB or the parallel interface card. For more information,
see “Installing an Internal Solutions Port” on page 38. b Print a menu settings page, and then check if the USB or parallel
interface card is listed in the Installed Features list.
Is the USB or parallel interface card listed in the Installed Features list?
The problem is solved. Contact customer support.
Check the cable and the USB or parallel interface card connection.
Use the correct cable, and then make sure it is securely connected to the USB or parallel interface card.
Does the USB or parallel interface card operate correctly?
Turn on Jam Recovery.
The problem is solved. Contact customer support.
a From the home screen, navigate to:
> Settings > General Settings > Print Recovery b From the Jam Recovery menu, touch the arrows to scroll to On or
Auto. c Touch Submit.
Do pages reprint after a jam?

Go to step 2. The problem is solved.
a Pull out the tray, and then do one or more of the following:
If jam recovery is enabled, then the print jobs will reprint automatically.
Do paper jams still occur frequently?
Go to step 3. The problem is solved.
a Load paper from a fresh package.
Do paper jams still occur frequently?
Contact customer support.
The problem is solved.
a Review the tips on avoiding jams. For more information, see “Avoiding
jams” on page 265. b Follow the recommendations, and then resend the print job.
Do paper jams still occur frequently?
Check the entire paper path for jammed paper.
Contact customer support.
The problem is solved.
a Remove any jammed paper. b From the scanner control panel, touch Continue to clear the message.
Does the paper jam message remain?

Go to step 2. Select one of the Print and Hold options, and then resend the print job. For more information, see “Printing confidential and other held jobs” on page 98.
Open the held jobs folder on the scanner display, and then verify that your print job is listed.
Is your print job listed in the held jobs folder?
Step 2 The print job may contain a formatting error or an invalid data.
The problem is solved. Go to step 3.
If you are printing from the Internet, then the printer may be reading multiple job titles as duplicates and deleting all jobs except the first one.
a Open the Print Properties folder. b From the Print and Hold dialog, select the Keep duplicate
documents check box. c Enter a PIN number.
For Macintosh users Save each print job, name each job differently, and then send the individual jobs to the printer.
Does the job print?
The problem is solved. Add additional printer memory.
Free up additional printer memory by deleting some of the held jobs.
Does the job print?

a Use envelopes that have been stored in a dry environment.
Contact customer support.
The problem is solved.
Does the envelope seal when printing?
Go to step 2. Insert the flash drive into the front USB port.
Check if the flash drive is inserted into the front USB port.
Is the flash drive inserted into the front USB port?
Wait until the scanner is ready, then view the held jobs list, and then print the documents.
Go to step 3.
Check if the indicator light on the scanner control panel is blinking green.
Is the indicator light blinking green?
Go to step 4. The problem is solved.
a Check for an error message on the display. b Clear the message.
Does the error message still appear?
Step 4 Check if the flash drive is supported.
Go to step 5. The problem is solved.
For more information on tested and approved USB flash drives, see “Supported flash drives and file types” on page 96.
Does the error message still appear?
Contact customer support.
The problem is solved.
Check if the USB port is disabled by the system support person.
Does the error message still appear?

Deactivate Hex Trace mode.
Go to step 2.
Make sure the printer is not in Hex Trace mode.
Is the printer in Hex Trace mode?
Contact customer support.
The problem is solved.
a From the scanner control panel, select Standard Network or
Network [x], and then set SmartSwitch to On. b Resend the print job.
Do incorrect characters print?
The problem is solved. Go to step 2.
a Check if you are printing on paper that is supported by the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 3.
a From the Paper menu on the scanner control panel, set the paper size
and type to match the paper loaded in the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 4.
a Depending on your operating system, specify the paper size from the
Printing Preferences or from the Print dialog. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Contact customer support.
a Check if the trays are not linked. b Resend the print job.
Did the job print from the correct tray or on the correct paper?

The problem is solved. Go to step 2.
a From the Finishing menu on the scanner control panel, set Collate to
(1,2,3) (1,2,3). b Resend the print job.
Did the job print and collate correctly?
The problem is solved. Go to step 3.
a From the printer software, set Collate to (1,2,3) (1,2,3).
Did the job print and collate correctly?
The problem is solved. Contact customer support.
Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Did the job print and collate correctly?
Multiple‑language PDF files do not print
The problem is solved. Go to step 2.
a Check if the print options for the PDF output are set to embed all fonts.
For more information, see the documentation that came with Adobe Acrobat. b Generate a new PDF file, and then resend the print job.
Do the files print?
The problem is solved. Contact customer support.
a Open the document you want to print in Adobe Acrobat. b Click File > Print > Advanced > Print As Image > OK > OK.
Do the files print?

The problem is solved. Go to step 2.
a Make sure the size of the paper loaded in the tray matches the fuser
type.
Does the print speed increase?
The problem is solved. Contact customer support.
a Replace the fuser. For more information on installing the fuser, see
the instruction sheet that came with the part. b Resend the print job.
Does the print speed increase?
The problem is solved. Go to step 2.
a From the document you are trying to print, open the Print dialog and
check if you have selected the correct printer.
Do the jobs print?
The problem is solved. Go to step 3.
a Check if the scanner and the printer are plugged in and turned on, and
if Ready appears on the scanner display. b Resend the print job.
Do the jobs print?
Step 3 If an error message appears on the scanner display, then clear the message.
The problem is solved. Go to step 4.
Do the jobs print?

The problem is solved. Go to step 5.
a Check if the ports (USB, serial, or Ethernet) are working and if the
cables are securely connected to the computer and to the scanner.
Do the jobs print?
The problem is solved. Go to step 6.
a Turn off the printer and the scanner, then wait for about 10 seconds,
and then turn them back on. b Resend the print job.
Do the jobs print?
The problem is solved. Contact customer support.
a Remove, and then reinstall the scanner software. For more
information, see “Installing the scanner” on page 55.
Do the jobs print?
Go to step 2. The problem is solved.
Change the environmental settings of the printer.
a From the scanner control panel, navigate to:
Settings > General Settings b Select Eco‑Mode or Quiet Mode, and then select Off.
Did the print job take longer than expected?
Go to step 3. The problem is solved.
Reduce the number and size of fonts, the number and complexity of images, and the number of pages in the print job, and then resend the job
Did the print job take longer than expected?

Go to step 4. The problem is solved.
a Remove held jobs stored in the scanner memory. b Resend the print job.
Did the print job take longer than expected?
Go to step 5. The problem is solved.
a Disable the Page Protect feature.
From the scanner control panel, navigate to: Settings > General Settings > Print Recovery > Page Protect > Off b Resend the print job.
Did the print job take longer than expected?
Go to step 6. The problem is solved.
a Check if the cable connections to the scanner and print server are
secure. For more information, see the setup documentation that came with the scanner. b Resend the print job.
Did the print job take longer than expected?
Contact customer support.
The problem is solved.
Install additional scanner memory, and then resend the print job.
Did the print job take longer than expected?
The problem is solved. Go to step 2.
a Open the trays, and then check if they contain paper of the same size
and type.
Do the trays link correctly?

The problem is solved. Contact customer support.
a From the scanner control panel, set the paper size and paper type in
the Paper menu to match the paper loaded in the trays to be linked.
Do the trays link correctly?
Increase the printing timeout.
The problem is solved. Check the original file for manual page breaks.
a From the home screen, navigate to:
> Settings > General Settings > Timeouts b Increase the Print Timeout setting, and then touch Submit.
c Resend the print job.
Did the file print correctly?

Go to step 2. The problem is solved.
a Print a font sample list to check if the fonts you are using are supported
by the printer.
1 From the scanner control panel, navigate to:
> Reports > Print Fonts 2 Touch PCL Fonts or PostScript Fonts. b Use a font that is supported by the printer or install the font that you
want to use. For more information, contact your system support person. c Resend the print job.
Do prints still contain characters that have jagged or uneven edges?
Contact customer support.
The problem is solved.
a Use a font that is supported by the printer or install the font that you
want to use on your computer. For more information, contact your system support person. b Resend the print job.
Do prints still contain characters that have jagged or uneven edges?

a Move the width and length guides in the tray to the correct positions
for the paper loaded. b Resend the print job.

Go to step 3. Do one or more of the following:
From the scanner control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.
Do the paper size and type match the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.
Is the page or image clipped?
Contact customer support.
The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge. 2 Remove the imaging unit.
Is the page or image clipped?
The problem is solved. Go to step 2.
a Make sure the size of the paper loaded in the tray matches the fuser
type.
Do compressed images still appear?


a Replace the fuser. For more information on installing the fuser, see
the instruction sheet that came with the part. b Resend the print job.

a From the Quality Menu on the scanner control panel, reduce the toner
a Remove the toner cartridge. b Remove the imaging unit.
Replace the imaging unit, and then resend the print job.
Troubleshooting 326


a Make sure your software program is using a correct fill pattern. b Resend the print job.
a Load the specified tray or feeder with a recommended type of paper. b Resend the print job.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Replace the imaging unit, and then resend the print job.
Troubleshooting 327

ABCD ABCD ABCD
The problem is solved. Go to step 2.
a Move the width and length guides in the tray to the correct positions
for the paper size loaded. b Resend the print job.
Are the margins correct?
Go to step 3. Do one or more of the following:
From the scanner control panel, set the paper size in the Paper menu to match the paper loaded in the tray.
Does the paper size match the paper loaded in the tray?
The problem is solved. Contact customer support.
a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.
Are the margins correct?

Go to step 2. Adjust the width and length guides.
Move the width and length guides in the tray to the correct positions for the size of the paper loaded.
Are the width and length guides positioned correctly?
Go to step 3. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
From the scanner control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the paper still curled?
Go to step 5. The problem is solved.
a Remove the paper from the tray, and then turn it over. b Resend the print job.
Is the paper still curled?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Is the paper still curled?

Go to step 2. The problem is solved.
a Check if there is packing material left on the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Check if the packing material is properly removed from the imaging unit.
Is the printer still printing blank pages?
Go to step 3. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Is the printer still printing blank pages?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the printer still printing blank pages?


1 Remove the toner cartridge, and then the imaging unit.
Replace the imaging unit, and then resend the print job.
) ) ABCDE
ABCDE ABCDE
Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded in the tray. b Resend the print job.
Do print irregularities still appear?
Go to step 3. Specify the paper size and type from the tray settings to match the paper loaded in the tray.
From the scanner control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.
Do the printer settings match the type and weight of the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do print irregularities still appear?

From the scanner control panel, set the paper texture in the Paper menu to match the paper loaded in the tray.
Go to step 5.
Check if the paper loaded in the tray has texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Do print irregularities still appear?
Contact customer support at http://support.lexmar k.com or your service representative.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do print irregularities still appear?
Go to step 2. The problem is solved.
a From the Quality menu on the scanner control panel, reduce the toner
darkness.
Is the print still too dark?

Go to step 3. Do one or more of the following:
a From the scanner control panel, set the paper type, texture and weight
in the Paper menu to match the paper loaded in the tray. b Resend the print job.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type, texture
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too dark?
From the scanner control panel, change the texture settings in the Paper Texture menu to match the paper you are printing on.
Go to step 5.
Check if the paper loaded in the tray has texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too dark?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the print still too dark?

Go to step 2. The problem is solved.
a From the Quality menu on the scanner control panel, increase the
toner darkness.
Is the print still too light?
Go to step 3. Change the paper type, texture, and weight to match the paper loaded in the tray.
From the scanner control panel, set the paper type, texture, and weight in the Paper menu to match the paper loaded in the tray.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too light?
From the scanner control panel, change the texture settings in the Paper Texture menu to match the paper you are printing on.
Go to step 5.
Make sure that the paper has no texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too light?

Go to step 7. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Is the print still too light?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the print still too light?
Go to step 2. The problem is solved.
a Replace the imaging unit if the distance between the defects is equal
to any of the following:
Do repeating defects still appear on prints?
Contact customer support.
The problem is solved.
a Replace the fuser if the distance between the defects is equal to either
of the following:
Do repeating defects still appear on prints?


Go to step 2. Load paper with the correct paper type and weight in the tray.
Load paper with the correct paper type and weight in the tray.
Is paper with the correct paper type and weight loaded in the tray?
Go to step 3. Change the paper loaded in the tray to match the paper type and weight specified in the tray settings.
From the scanner control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Is the tray set to the type and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do shadow images still appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do shadow images still appear on prints?
) ) ABCDE
ABCDE ABCDE

Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded. b Resend the print job.
Is the print still skewed?
Contact customer support.
The problem is solved.
a Check if you are printing on a paper that is supported by the tray. b Resend the print job.
Is the print still skewed?
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the tray from Printing
Preferences or the Print dialog. b Resend the print job.
Do streaked horizontal lines appear on prints?
Go to step 3. Change the paper type and weight to match the paper loaded in the tray.
From the scanner control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked horizontal lines appear on prints?


1 Remove the toner cartridge, and then the imaging unit.
Replace the imaging unit, and then resend the print job.
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do streaked vertical lines appear on prints?
Go to step 3. Do one or more of the following:
From the scanner control panel, set the paper texture, type, and weight in the Paper menu to match the paper loaded in the tray.
Do the paper texture, type, and weight match the paper in the tray?

Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked vertical lines appear on prints?
Go to step 5. The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge, and then the imaging unit.
Do streaked vertical lines appear on prints?
Contact customer support at http://support.lexmar k.com or your service representative.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do streaked vertical lines appear on prints?
ABCDE
ABCDE ABCDE
The problem is solved. Go to step 2.
a Reinstall the imaging unit.
1 Remove the toner cartridge, and then the imaging unit.
Did the toner fog or background shading disappear from the prints?


Replace the imaging unit, and then resend the print job.
Did the toner fog or background shading disappear from the prints?

Go to step 2. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
From the Paper menu on the scanner control panel, check the paper type and weight.
Do the paper type and weight match the paper loaded in the tray?
From the Paper menu on the scanner control panel, set the paper texture.
Check if you are printing on paper that is heavy or has texture or rough finishes.

Replace the imaging unit, and then resend the print job.
Troubleshooting 340


Go to step 2. Set the paper type to Transparency.
From the scanner control panel, set the paper type in the Paper menu to match the paper loaded in the tray.
Is the paper type for the tray set to Transparency?
a Check if you are using a recommended type of transparency. b Resend the print job.

Replace the imaging unit, and then resend the print job.

a Make sure your software program is using a correct fill pattern. b Resend the print job.
Troubleshooting 341

Go to step 3. The problem is solved.
a From the scanner control panel, set the paper type and weight in the
Paper menu to match the paper loaded in the tray. b Resend the print job.
Do vertical voids appear on prints?
Go to step 4. The problem is solved.
Check if you are using a recommended type of paper.
a Load the specified tray or feeder with a recommended type of paper. b Resend the print job.
Do vertical voids appear on prints?
Go to step 5. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Do vertical voids appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do vertical voids appear on prints?

Clear the error or status message.
Go to step 2.
Check if an error or status message appears on the scanner display.
Does an error or status message appear?
Go to step 3. Connect the power cord to the scanner and to a properly grounded electrical outlet.
Check if the power cord is plugged into the scanner and to a properly grounded electrical outlet.
Is the power cord plugged into the scanner and to a properly grounded electrical outlet?
Go to step 4. Connect the power cord to the printer and to a properly grounded electrical outlet.
Check if the power cord is plugged into the printer and to a properly grounded electrical outlet.
Is the power cord plugged into the printer and to a properly grounded electrical outlet?
The problem is solved. Contact customer support.
Turn off the printer and the scanner, wait for about 10 seconds, and then turn them back on.
Did Performing Self Test and Ready appear?
Go to step 2. Place the document or photo facedown on the scanner glass in the lower left corner.
Check the placement of the document or photo.
Make sure the document or photo is loaded facedown on the scanner glass in the lower left corner.
Is the document or photo loaded correctly?
Go to step 3. Change the paper size setting to match the paper loaded in the tray, or load the tray with paper that matches the paper size setting.
Check if the paper size setting matches the size of the paper loaded in the tray.
From the Paper menu on the scanner control panel, check the Paper Size setting.
Does the paper size setting match the size of the paper loaded in the tray.

The problem is solved. Contact customer support.
a Specify the paper size. Depending on your operating system, specify
the paper size in Printing Preferences or the Print dialog. b Resend the copy job.
Do copies print properly?
Clear the error or status message.
Go to step 2.
Check if an error or status message appears on the display.
Does an error or status message appear?
Go to step 3. Increase the scan resolution setting for a higher‑quality output.
Check the quality of the original document.
Is the quality of the original document satisfactory?
Go to step 4. See “Cleaning the scanner glass” on page 240.
If dark marks appear on prints, then clean the scanner glass and the ADF glass using a clean, lint-free cloth dampened with water.
Is the scanner glass clean?
Go to step 5. See “Print quality problems” on page 323.
Send a print job, and then check for print quality problems.
a From the General Settings menu, adjust the Eco‑Mode settings. b From the Copy menu, adjust the toner darkness.
c If the print remains faded, then replace the toner cartridge.
Is the print quality satisfactory?
Go to step 6. Place the document or photo facedown on the scanner glass in the upper left corner.
Check the placement of the document or photo.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Is the document or photo loaded correctly?
The problem is solved. Go to step 7.
Increase the scan resolution setting for a higher‑quality output.
Did the increased resolution produce a higher‑quality output?

Go to step 8. Change the Content Type and Content Source settings to match the document being scanned.
Check the copy settings.
From the Copy screen, check if the Content Type and Content Source settings are correct for the document being scanned.
Are the Content Type and Content Source settings correct for the document being scanned?
Go to step 9. The problem is solved.
Check for patterns on print.
a From the Copy screen, navigate to:
Advanced Options > Advanced Imaging > Sharpness > select a lower setting b On the Copy screen, make sure no scaling is being selected.
Do patterns appear on prints?
Go to step 10. The problem is solved.
Check for missing or faded text on prints.
a From the Copy screen, navigate to:
Advanced Options > Advanced Imaging b Adjust the settings:
Do prints have missing or faded text?
Contact customer support.
The problem is solved.
Check for washed‑out or overexposed output.
a From the Copy screen, navigate to:
Advanced Options > Advanced Imaging b Adjust the settings of the following:
Do pages show washed‑out or overexposed prints?

Check if there are no obstructions between the scanner unit and the printer.
The problem is solved. Contact customer support.
a Lift the scanner unit. b Remove any obstruction that keeps the scanner unit open.
c Lower the scanner unit.
Did the scanner unit close properly?
Contact your telephone company to check if your telephone line is subscribed to the caller ID service.
The problem is solved. Contact customer support.
Does the caller ID appear?
Troubleshooting 346 · Action Yes No · Action Yes No

Clear the error or status message.
Go to step 2.
Check if an error or status message appears on the display.
Is there an error or status message on the display?
Go to step 3. Connect the power cord to the printer and a properly grounded electrical outlet.
Check if the power cord is plugged into the printer and a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
Go to step 4. Turn on the printer, and then wait until Ready appears on the display.
Check the power.
Check if the printer is plugged in and turned on, and if Ready appears on the display.
Is the printer turned on, and does Ready appear on the display?
Go to step 5. Securely connect the cables.
Check the printer connections.
If applicable, check if the cable connections for the following equipment are secure:
Are the cable connections secure?
The problem is solved. Go to step 6.
a Check the telephone wall jack.
1 Plug the telephone cable into the wall jack. 2 Listen for a dial tone. 3 If you do not hear a dial tone, then plug a different telephone cable into the wall jack. 4 If you still do not hear a dial tone, then plug the telephone cable into a different wall jack. 5 If you hear a dial tone, then connect the printer to that wall jack. b Try sending or receiving a fax.
Can you send or receive a fax?

Go to step 7. Connect the printer to an analog phone service or the correct digital connector.
Check if the printer is connected to an analog phone service or the correct digital connector.
The fax modem is an analog device. Certain devices can be connected to the printer so that digital telephone services can be used.
Is the printer connected to an analog phone service or the correct digital connector?
Check for a dial tone.
Did you hear a dial tone?
Step 8 Temporarily disconnect other equipment (such as answering machines, computers with modems, or telephone line splitters) between the printer and the telephone line, and then try sending or receiving a fax.
The problem is solved. Go to step 9.
Can you send or receive a fax?
The problem is solved. Go to step 10.
a Temporarily disable call waiting. Contact your telephone company to
obtain the keypad sequence for temporarily disabling call waiting. b Try sending or receiving a fax.
Can you send or receive a fax?

The problem is solved. Go to step 11.
a Temporarily disable voice mail service. For more information, contact
your telephone company.
Can you send or receive a fax?
The problem is solved. Contact customer support.
Scan the original document one page at a time.
a Dial the fax number. b Scan the document one page at a time.
Can you send or receive a fax?
The problem is solved. Go to step 2.
Check if the printer is in Fax mode.
From the home screen, touch Fax to put the printer in Fax mode, and then send the fax.
Can you send faxes?
The problem is solved. Go to step 3.
a Load the original document properly.
Load the original document facedown, long edge first into the ADF tray or facedown on the scanner glass in the lower left corner.
Can you send faxes?
The problem is solved. Contact customer support.
Set up the shortcut number properly, and then resend the fax.
Can you send faxes?

The problem is solved. Go to step 2.
Check the tray or feeder.
If empty, then load paper in the tray or feeder.
Can you receive faxes?
The problem is solved. Go to step 3.
Check the ring count delay settings.
a Open a Web browser, and then type the scanner IP address in the
address field.
c In the “Rings to Answer” field, enter the number of times you want
the phone to ring before the printer answers. d Click Submit.
Can you receive faxes?
The problem is solved. Contact customer support.
Replace the toner cartridge. For more information, see the instruction sheet that came with the supply.
Can you receive faxes?

a From the scanner home screen, navigate to:
The problem is solved. Contact customer support.
> Settings > General Settings > Run initial setup > Yes > Submit b Turn off the printer and the scanner, and then turn them back on.
The “Select your language” screen appears on the scanner display.
. d Select a country or region, and then touch Next. e Select a time zone, and then touch Next.
c Select a language, and then touch
f Select Fax and E‑mail, and then touch Next.
Are the fax and e‑mail functions set up?
The problem is solved. Go to step 2.
Ask the person who sent you the fax to:
a Check if the quality of the original document is satisfactory. b Increase the fax scan resolution, if possible.
c Resend the fax.
Is the fax print quality satisfactory?

The problem is solved. Go to step 3.
Decrease the incoming fax transmission speed.
a Open a Web browser, and then type the scanner IP address in the
address field.
c In the Max Speed menu, click one of the following:
Is the fax print quality satisfactory?
The problem is solved. Contact customer support.
Replace the toner cartridge.
When Cartridge low [88.xy] appears, replace the cartridge, and then resend the fax.
Is the fax print quality satisfactory?

Go to step 4. Go to step 2.
Make sure the scanner is turned on and that Ready appears on the scanner display before scanning a job.
Does Ready appear before scanning the job?
Go to step 4. Go to step 3.
Turn off the scanner, then wait for about 10 seconds, and then turn it back on.
Does Ready appear before scanning the job?
The problem is solved. Go to step 4.
a If an error message appears on the scanner display, then clear the
message. b Resend the scan job.
Are you able to scan from a computer?
The problem is solved. Contact customer support.
a Check the cable connections between the scanner and the print server
to make sure they are secure.
For more information, see the setup documentation that came with the scanner. b Resend the scan job.
Are you able to scan from a computer?
a Check the placement of the document or photo.
The problem is solved. Contact customer support.
Make sure the document or photo is loaded facedown on the scanner glass in the lower left corner. b Scan the document or photo again.
Is the document or photo scanned correctly?

Clear the error message.
Go to step 2.
Check if an error message appears on the scanner display.
Is there an error message on the scanner display?
Go to step 3. Increase the scan resolution settings for a higher‑quality output.
Check the quality of the original document.
Is the quality of the original document satisfactory?
Go to step 4. See “Cleaning the scanner glass” on page 240.
Clean the scanner glass and the ADF glass using a clean, lint‑free cloth dampened with water.
Is the scanner glass clean?
Go to step 5. Place the document or photo facedown on the scanner glass in the upper left corner.
Check the placement of the document or photo.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Is the document or photo loaded correctly?
Go to step 6. See “Print quality problems” on page 323.
Send a print job, and then check for print quality problems.
Is the print quality satisfactory?
The problem is solved. Go to step 7.
Increase the scan resolution settings for a higher‑quality output.
Did the increased resolution produce a higher‑quality output?
Contact customer support.
Change the Content Type and Content Source settings to match the document being scanned.
Check the scan settings.
From the Scan screen, make sure the Content Type and Content Source settings are correct for the document being scanned.
Are the Content Type and Content Source settings correct for the document being scanned?

Go to step 2. Connect the cables properly.
Check the cable connections.
Make sure the Ethernet or USB cable is securely connected to the computer and the printer.
Are the cables securely connected?
Change the file name. Go to step 3.
Check if the file name is already in use.
Is the file name already in use?
Close the file you are scanning.
Go to step 4.
Check if the document or photo you want to scan is open in another application or being used by another user.
Is the file you want to scan open in another application or being used by another user?
Go to step 5. Select the Append time stamp or Overwrite existing file check box in the destination configuration settings.
Check if either the Append time stamp or the Overwrite existing file check box is selected in the destination configuration settings.
Is the Append time stamp or Overwrite existing file check box selected in the destination configuration settings?
The problem is solved. Go to step 6.
From the Flash Drive menu, reduce the scan resolution settings, and then resend the scan job.
Does the job scan?
The problem is solved. Change the Content Type and Content Source settings to match the document being scanned.
Check the scan settings.
From the Scan screen, make sure the Content Type and Content Source settings are correct for the document being scanned.
Are the Content Type and Content Source settings correct for the document being scanned?

Check if there are obstructions in the scanner unit.
The problem is solved. Contact customer support.
a Lift the scanner unit. b Remove any obstruction keeping the scanner unit open.
c Lower the scanner unit.
Did the scanner unit close correctly?
Step 1 Check if other applications are interfering with the scan.
Go to step 2. The problem is solved.
Close all applications that are not being used.
Does scanning still take too long or freeze the computer?
Contact customer support.
The problem is solved.
Select a lower scan resolution.
Does scanning still take too long or freeze the computer?
Go to step 2. Turn on the scanner.
Check if the scanner is turned on.
Is the scanner turned on?
Go to step 3. Connect the Ethernet cable securely to the scanner and the computer, print server, option, or other network device.
Check if the Ethernet cable is securely attached to the scanner and the computer, print server, option, or other network device.
Is the Ethernet cable securely attached to the scanner and the computer, print server, option, or other network device?
Go to step 4. Connect the power cord to the scanner and to a properly grounded electrical outlet.
Check if the power cord is plugged into the scanner and to a properly grounded electrical outlet.
Is the power cord plugged into the scanner and to a properly grounded electrical outlet?

Turn on the switch or reset the breaker.
Go to step 5.
Check if the electrical outlet is turned off by a switch or breaker.
Is the electrical outlet turned off by a switch or breaker?
Connect the scanner power cord directly to a properly grounded electrical outlet.
Go to step 6.
Check if the scanner is plugged into any surge protectors, uninterruptible power supplies, or extension cords.
Is the scanner plugged into any surge protectors, uninterruptible power supplies, or extension cords?
Unplug the other electrical equipment, and then turn on the scanner. If the scanner does not work, then reconnect the other electrical equipment, and then go to step 6.
Go to step 7.
Check the other electrical equipment plugged into the outlet.
Are the other electrical equipment working?
The problem is solved. Contact customer support.
Turn off the scanner, then wait for about 10 seconds, and then turn it back on.
Is the scanner working?

Go to step 2. Contact customer support.
Check the system log for relevant details.
a Open a Web browser, and then type the scanner IP address in the
address field.
If you do not know the IP address of the scanner, then you can:
c From the Filter menu, select an application status. d From the Application menu, select an application, and then click
Submit.
Does an error message appear in the log?
Step 2 Resolve the error.
The problem is solved. Contact customer support.
Is the application working now?
Go to step 2. Type the correct scanner IP address in the address field of your Web browser.
Make sure the scanner IP address is correct.
View the scanner IP address:
Is the scanner IP address correct?

Go to step 3. Turn on the printer, and then the scanner.
Check if the scanner and printer are turned on and if Ready appears on the scanner display.
Are the scanner and the printer turned on and does Ready appear on the scanner display?
Go to step 4. Contact your system support person.
Check if the network connection is working.
Is the network connection working?
Go to step 5. Tighten the cable connection.
Make sure the cable connections to the scanner and print server are secure.
For more information, see the setup documentation that came with the scanner.
Are the cable connections to the scanner and print server secure?
Go to step 6. Contact your system support person.
Temporarily disable the Web proxy servers.
Are the Web proxy servers disabled?
The problem is solved. Contact customer support.
Access the Embedded Web Server again by typing the correct IP address in the address field.
Did the Embedded Web Server open?
When you contact customer support, describe the problem you are experiencing, the printer control panel light sequence, and the troubleshooting steps you have already taken to find a solution.
You need to know your printer model type and serial number. For more information, see the label on the inside top front cover of the printer. The serial number is also listed on the menu settings page.
Lexmark has various ways to help you solve your printing problem. Visit the Lexmark Web site at http://support.lexmark.com, and then select one of the following:
Tech Library You can browse our library of manuals, support documentation, drivers, and other downloads to help you
solve common problems.
E-mail You can send an e-mail to the Lexmark team, describing your problem. A service representative will respond and provide you with information to solve your problem.

Live chat You can chat directly with a service representative. They can work with you to solve your printer problem or provide assistance through Assisted Service where the service representative can remotely connect to your computer through the Internet to troubleshoot problems, install updates, or complete other tasks to help you successfully use your Lexmark product.
Telephone support is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, visit the Lexmark Web site at http://support.lexmark.com.
Troubleshooting 360

Product name:
Machine type:
Model(s):
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
© 2014 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
Lexmark MX6500e · February 2014

Lexmark, Lexmark with diamond design, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
PrintCryption, ScanBack, and StapleSmart are trademarks of Lexmark International, Inc.
Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
The following terms are trademarks or registered trademarks of these companies:

CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Agfa Corporation

Univers Linotype-Hell AG and/or its subsidiaries
All other trademarks are the property of their respective owners.
This product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
This product may contain the following modular component(s):
Lexmark Regulatory Type/Model LEX-M01-005; FCC ID:IYLLEXM01005; IC:2376A-M01005
Lexmark Regulatory Type/Model LEX-M05-001; FCC ID: IYLLEXM05001; Industry Canada IC: 2376A-M05001
Lexmark Regulatory Type/Model LEX-M05-002; FCC ID: IYLLEXM05002; Industry Canada IC: 2376A-M05002
All licensing notices associated with this product can be viewed from the CD:\LEGAL directory of the installation software CD.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Printing One-sided: 57 dBA (MS710, MS711), 57 dBA (MS810n, MS810dn), 58 dBA (MS811n, MS811dn), 58 dBA (MS812dn); Two-sided: 56 dBA (MS710,

1-meter average sound pressure, dBA MS711), 56 dBA (MS810n, MS810dn), 57 dBA (MS811n, MS811dn), 58 dBA (MS812dn)
Scanning 45 dBA (mono), 44 dBA (color)
Values are subject to change. See www.lexmark.com for current values.
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products. If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching the metal frame of the printer.
Ambient operating temperature 16 to 32°C (60 to 90°F)
Shipping temperature -40 to 43.3°C (-40 to 110°F)
Storage temperature and relative humidity 1 to 35°C (34 to 95°F)
8 to 80% RH
Copying 55 dBA · Ready 36 dBA

The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Chapter I, Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 10 milliwatt gallium arsenide laser operating in the wavelength of 787-800 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
A laser notice label may be affixed to this printer as shown:
Opasnost - Nevidljivo lasersko zračenje kada su kasete uklonjene i poništena sigurnosna veza. Izbjegavati izlaganje zracima.
NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, ze zařízení je vysíláno neviditelné laserové záření. Nevystavujte se působení laserového paprsku. FARE - Usynlig laserstråling, når patroner fjernes, og spærreanordningen er slået fra. Undgå at blive udsat for laserstrålen.
VAARA - Näkymätöntä lasersäteilyä on varottava, kun värikasetit on poistettu ja lukitus on auki. Vältä lasersäteelle altistumista. GEFAHR - Unsichtbare Laserstrahlung beim Herausnehmen von Druckkassetten und offener Sicherheitssperre. Laserstrahl meiden.
ΚΙΝΔΥΝΟΣ - Έκλυση αόρατης ακτινοβολίας laser κατά την αφαίρεση των κασετών και την απασφάλιση της μανδάλωσης. Αποφεύγετε την έκθεση στην ακτινοβολία laser.
VESZÉLY – Nem látható lézersugárzás fordulhat elő a patronok eltávolításakor és a zárószerkezet felbontásakor. Kerülje a lézersugárnak való kitettséget.
ОПАСНО! Невидимое лазерное излучение при извлеченных картриджах и снятии блокировки. Избегайте воздействия лазерных лучей.
Pozor – Nebezpečenstvo neviditeľného laserového žiarenia pri odobratých kazetách a odblokovanej poistke. Nevystavujte sa lúčom. PELIGRO: Se producen radiaciones láser invisibles al extraer los cartuchos con el interbloqueo desactivado. Evite la exposición al haz de láser.
FARA – Osynlig laserstrålning när patroner tas ur och spärrmekanismen är upphävd. Undvik exponering för laserstrålen.
危险 - 当移除碳粉盒及互锁失效时会产生看不见的激光辐射,请避免暴露在激光光束下。
危険 - カートリッジが取り外され、内部ロックが無効になると、見えないレーザー光が放射されます。 このレーザー光に当たらないようにしてください。
Power consumption
Product power consumption
The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs.
One-sided: 700 W (MS710, MS711), 700 W (MS810n, MS810dn), 770 W (MS811n, MS811dn), 830 W (MS812dn); Two-sided: 500 W (MS710, MS711), 500 W (MS810n, MS810dn), 560 W (MS811n, MS811dn), 630 W (MS812dn)

Mode Description Power consumption (Watts)
Copy The product is generating hard‑copy output from hard‑copy original documents.
Scan The product is scanning hard‑copy documents. 70 W
Ready The product is waiting for a print job. 40 W
Sleep Mode The product is in a high‑level energy‑saving mode. 25 W
Off The product is plugged into a wall outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.
This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 20
By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 120 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the wall outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe A est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.

This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class A limits of EN 55022 and safety requirements of EN 60950‑1.
This is a product that complies with the emission requirements of EN55022 Class A limits and immunity requirements of EN55024. This product is not intended to be used in residential/domestic environments.
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
This section contains regulatory information pertaining to products that contain telecommunication terminal equipment such as facsimile.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachments (ACTA). On the back of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to your telephone company.
This equipment uses the RJ-11C Universal Service Order Code (USOC) jack.
A plug and jack used to connect this equipment to the premises’ wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See your setup documentation for more information.
The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact your local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (for example, 03 is a REN of 0.3). For earlier products, the REN is shown separately on the label.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. You will also be advised of your right to file a complaint with the FCC.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
If you experience trouble with this equipment, for repair or warranty information, contact Lexmark International, Inc. at www.lexmark.com or your Lexmark representative. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
This equipment contains no user serviceable parts. For repair and warranty information, contact Lexmark International, Inc. See the previous paragraph for contact information.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. It is recommended that the customer install an appropriate AC surge arrestor in the AC outlet to which this device is connected. An appropriate AC surge arrestor is defined as one that is suitably rated, and certified by UL (Underwriter's Laboratories), another NRTL (Nationally Recognized Testing Laboratory), or a recognized safety certification body in the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless said message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)
See your user documentation in order to program this information into your fax machine.
This product meets the applicable Industry Canada technical specifications. The Ringer Equivalence Number (REN) is an indication of the maximum number of terminals allowed to be connected to a telephone interface. The terminus of an interface may consist of any combination of devices, subject only to the requirement that the sum of the RENs of all the devices does not exceed five. The modem REN is located on the rear of the equipment on the product labeling.
Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. It is recommended that the customer install an appropriate AC surge arrestor in the AC outlet to which this device is connected. An appropriate AC surge arrestor is defined as one that is suitably rated, and certified by UL (Underwriter’s Laboratories), another NRTL (Nationally Recognized Testing Laboratory), or a recognized safety certification body in the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges.
This equipment uses CA11A telephone jacks.

Ce produit est conforme aux spécifications techniques d’Industrie Canada. Le numéro REN (ringer equivalence number : numéro d’équivalence de sonnerie) fournit une indication du nombre maximum de terminaux pouvant être connectés à l’interface téléphonique. En bout de ligne, le nombre d’appareils qui peuvent être connectés n’est pas directement limité, mais la somme des REN de ces appareils ne doit pas dépasser cinq. Le numéro REN du modem est indiqué sur l’étiquette produit située à l’arrière de l’équipement.
Les compagnies de téléphone constatent que les surtensions électriques, en particulier celles dues à la foudre, entraînent d'importants dégâts sur les terminaux privés connectés à des sources d’alimentation CA. Il s’agit-là d’un problème majeur d’échelle nationale. En conséquence, il vous est recommandé de brancher un parasurtenseur dans la prise de courant à laquelle l’équipement est connecté. Utilisez un parasurtenseur répondant à des caractéristiques nominales satisfaisantes et certifié par le laboratoire d’assureurs UL (Underwriter’s Laboratories), un autre laboratoire agréé de type NRTL (Nationally Recognized Testing Laboratory) ou un organisme de certification agréé dans votre région ou pays. Ceci prévient tout endommagement de l’équipement causé par les orages et autres surtensions électriques.
Cet équipement utilise des prises de téléphone CA11A.
The following are special conditions for the Facsimile User Instructions. The grant of a telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.
This equipment shall not be set up to make automatic calls to the Telecom's 111 Emergency Service.
This equipment may not provide for the effective hand-over of a call to another device connected to the same line.
This equipment should not be used under any circumstances that may constitute a nuisance to other Telecom customers.
Some parameters required for compliance with Telecom's telepermit requirements are dependent on the equipment associated with this device. The associated equipment shall be set to operate within the following limits for compliance to Telecom's specifications:
This product requires a Swiss billing tone filter (Lexmark part number 80D1877) to be installed on any line which receives metering pulses in Switzerland. The filter must be used, as metering pulses are present on all analog telephone lines in Switzerland.

Cet appareil nécessite l’utilisation d’un filtre de tonalité de facturation suisse (nº de référence Lexmark : 80D1877) devant être installé sur toute ligne recevant des impulsions de comptage en Suisse. Ce filtre doit être utilisé pour toute installation car ces impulsions existent sur toutes les lignes téléphoniques suisses.
Für dieses Produkt muss ein schweizerischer Billing Tone Filter zur Zählzeichenübertragung (Lexmark Teilenummer 80D1877) für jede Leitung installiert werden, über die in der Schweiz Zeitsteuertakte übertragen werden. Die Verwendung des Filters ist obligatorisch, da in allen analogen Telefonleitungen in der Schweiz Zeitsteuertakte vorhanden sind.
Questo prodotto richiede un filtro toni Billing svizzero, (codice Lexmark 80D1877) da installare su tutte le linee che ricevono impulsi remoti in Svizzera. È necessario utilizzare il filtro poiché gli impulsi remoti sono presenti su tutte le linee analogiche in Svizzera.
Products bearing the CE mark are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class A limits of EN 55022 and safety requirements of EN 60950‑1.
Refer to the table at the end of the Notices section for further compliance information.
This section contains the following regulatory information pertaining to wireless products that contain transmitters, for example, but not limited to, wireless network cards or proximity card readers.

The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.
This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb
The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.
Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement.
Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada.
En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.
Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur et loin des fenêtres afin de garantir une protection optimale.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc-sc.gc.ca/rpb
Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme aux spécifications techniques d'Industry Canada.

Products bearing the CE mark are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, radio equipment and telecommunications terminal equipment, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class A limits of EN 55022 and safety requirements of EN 60950‑1.
Products equipped with 2.4GHz Wireless LAN option are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment.
Compliance is indicated by the CE marking.
Operation is allowed in all EU and EFTA countries, but is restricted to indoor use only.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product may be used in the countries indicated in the table below.
AT BE BG CH CY CZ DE DK EE
EL ES FI FR HR HU IE IS IT
LI LT LU LV MT NL NO PL PT
Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.
Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.
Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.
Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.
Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.
Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.
Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky
príslušné ustanovenia smernice 1999/5/ES.
Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country- specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web at http://support.lexmark.com.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark MX6500e

Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.

The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Elliptic Curve Cryptography (ECC) Cipher Suites for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Elliptic Curve Cipher Suites with SHA-256/382 and AES Galois Counter Mode (GCM) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Suite B Profile for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Addition of the Camellia Cipher Suites to Transport Layer Security (TLS) implemented in the product or service.
The use of certain patents in this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for AES-CCM ECC Cipher Suites for TLS implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for IKE and IKEv2 Authentication Using the Eliptic Curve Digital Signature Algorithm (ECDSA) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Suite B Cryptographic Suites for IPSec implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Algorithms for Internet Key Exchange version 1 (IKEv1) implemented in the product or service.







Configuration change, some held
Insufficient memory, some held
Remove packaging material, [area
jobs were not restored [57] 291 Defective flash detected [51] 291 Disk full 62 291 Disk full, scan job canceled 291 Disk must be formatted for use in
jobs will not be restored [37] 295 Load [paper source] with [custom
name] 301 Remove paper from [linked set bin
name] 302 Remove paper from all bins 301 Remove paper from bin [x] 302 Remove paper from standard
string] [paper orientation] 296 Load [paper source] with [custom
this device 292 Disk near full. Securely clearing
type name] [paper orientation] 296 Load [paper source] with [paper
output bin 302 Replace all originals if restarting
disk space. 292 Empty the hole punch box 292 Error reading USB drive. Remove
size] [paper orientation] 296 Load [paper source] with [paper
job. 302 Replace cartridge, 0 estimated
USB. 292 Error reading USB hub. Remove
type] [paper size] [paper orientation] 296 Load Manual Feeder with [custom
pages remain [88.xy] 302 Replace cartridge, printer region
hub. 292 Fax memory full 292 Fax partition inoperative. Contact
mismatch [42.xy] 302 Replace imaging unit, 0 estimated
string] [paper orientation] 297 Load Manual Feeder with [custom
pages remain [84.xy] 303 Replace jammed originals if
system administrator. 292 Fax server 'To Format' not set up.
type name] [paper orientation] 297 Load Manual Feeder with [paper
restarting job. 303 Replace last scanned page and
Contact system administrator. 292 Fax Station Name not set up.
size] [paper orientation] 297 Load manual feeder with [paper
jammed originals if restarting job. 303 Replace maintenance kit, 0
Contact system administrator. 293 Fax Station Number not set up.
type] [paper size] [paper orientation] 297 Load staples 297 Maintenance kit low [80.xy] 298 Maintenance kit nearly low
estimated pages remain [80.xy] 303 Replace missing fuser [31.xy] 304 Replace missing or unresponsive
Contact system administrator. 293 Imaging unit low [84.xy] 293 Imaging unit nearly low
[80.xy] 298 Maintenance kit very low, [x]
fuser [31.xy] 301 Replace roller kit [81.xy] 304 Replace separator pad 304 Replace unsupported cartridge
[84.xy] 293 Imaging unit very low, [x]
estimated pages remain [80.xy] 298 Memory full [38] 298 Memory full, cannot send
estimated pages remain [84.xy] 293 Incompatible output bin [x]
[32.xy] 304 Replace unsupported fuser
faxes 298 Network [x] software error
[32.xy] 304 Replace unsupported imaging unit
[59] 293 Incompatible tray [x] [59] 293 Incorrect paper size, open [paper
[54] 298 No analog phone line connected
[32.xy] 304 Replace wiper 304 Restore held jobs? 305 Scan document too long 305 Scanner automatic feeder cover
source] [34] 294 Insert hole punch box 294 Insert staple cartridge 294 Insert Tray [x] 294 Install bin [x] 294 Install Tray [x] 295 Insufficient memory for Flash
to modem, fax is disabled. 298 Non‑Lexmark [supply type], see
User’s Guide [33.xy] 299 Not enough free space in flash
open 305 Scanner disabled by admin
memory for resources [52] 299 Paper changes needed 299 Parallel port [x] disabled [56] 299 Printer had to restart. Last job
[840.01] 305 Scanner disabled. Contact system
Memory Defragment operation [37] 295 Insufficient memory to collate job
administrator if problem persists. [840.02] 305 Scanner jam, remove all originals
may be incomplete. 300 Reattach bin [x] 300 Reattach bins [x] – [y] 300 Reinstall missing or unresponsive
[37] 295 Insufficient memory to support
from the scanner [2yy.xx] 305 Scanner jam, remove jammed
Resource Save feature [35] 295 Insufficient memory, some Held
cartridge [31.xy] 301 Reinstall missing or unresponsive
originals from the scanner [2yy.xx] 305 Scanner locked, release lock under
Jobs were deleted [37] 295
imaging unit [31.xy] 301 Remove defective disk [61] 301
Index 384 · scanner 306




Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.