
User's Guide
Machine type(s):
Model(s):


Connect the power cord to a properly grounded electrical outlet that is near the product and easily accessible.
Do not place or use this product near water or wet locations.
Refer service or repairs, other than those described in the user documentation, to a service representative.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
Use only the telecommunications (RJ‑11) cord provided with this product or a 26 AWG or larger replacement when connecting this product to the public switched telephone network.
CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Use only the power cord provided with this product or the manufacturer's authorized replacement.
Safety information 6

CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
SAVE THESE INSTRUCTIONS.
Safety information 7

Learning about the printer 8
Finding information about the printer

Learning about the printer 9
When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any options, then leave enough room for them also. It is important to:

Learning about the printer 10

You can configure your printer by adding one optional 250‑ or 550‑sheet tray. For instructions on installing the optional tray, see “Installing optional trays” on page 19.

Learning about the printer 11


1 Printer control panel
10 Standard bin

Learning about the printer 12


When using the scanner glass:

Learning about the printer 13
1 2 3 4 5 6 7

8 9 11 12 13 10

2 Arrow buttons Scroll up and down or left and right.
4 Address book button View all the stored addresses.
7 Sleep button Enable Sleep mode or Hibernate mode.
Do the following to wake the printer from Sleep mode:
9 Start button Start a job, depending on which mode is selected.
13 Indicator light Check the status of the printer.
The colors of the indicator and Sleep button lights on the printer control panel signify a certain printer status or condition.

Learning about the printer 14
Indicator light Printer status
Off The printer is off or in Hibernate mode.
Blinking green The printer is warming up, processing data, or printing.
Solid green The printer is on, but idle.
Blinking red The printer requires user intervention.
Sleep button light Printer status
Off The printer is idle or in Ready state.
Solid amber The printer is in Sleep mode.
Blinking amber The printer is waking from or entering Hibernate mode.
Blinking amber for 0.1 second, then goes completely off for 1.9 seconds in pulsing pattern
The printer is in Hibernate mode.

Additional printer setup 15
Installing internal options
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electircal outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Open the controller board access door.


Additional printer setup 16
2 Open the controller board shield using the green handle.


3 Use the following illustration to locate the option card connector.


4 Close the shield, and then the access door.



Additional printer setup 17
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 15.
2 Unpack the optional card.
3 Holding the card by its sides, align the plastic pins (1) on the card with the holes (2) on the controller board.



Additional printer setup 18
4 Push the card firmly into place as shown in the illustration.

5 Close the controller board shield, and then the controller board access door.

Additional printer setup 19
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
CAUTION—TIPPING HAZARD: Floor‑mounted configurations require additional furniture for stability. You must use either a printer stand or printer base if you are using a high‑capacity tray and an input option, or more than one input option. If you purchased a multifunction printer (MFP) that scans, copies, and faxes, you may need additional furniture. For more information, see www.lexmark.com/multifunctionprinters.
Install the printer and any hardware options you have purchased in the following order:
For more information on installing a printer stand, optional 250‑ or 550‑sheet tray, or spacer, see the setup sheet that came with the option.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer using the power switch, and then unplug the power cord from the electrical outlet.

Additional printer setup 20



2 Unpack the tray, and then remove all packing material.
3 Pull out the tray from the base.

4 Remove any packing material from inside the tray.
5 Insert the tray into the base.
6 Place the tray near the printer.
7 Align the printer with the tray, and then slowly lower the printer into place.

Additional printer setup 21

8 Connect the power cord to the printer, then to a properly grounded electrical outlet, and then turn on the printer.



Additional printer setup 22
Connect the printer to the computer using a USB cable or to the network using an Ethernet cable.
Make sure to match the following:

1 Printer power cord socket
Connect the printer to a properly grounded electrical outlet.
2 Power switch Turn the printer on or off.
3 Ethernet port Connect the printer to an Ethernet network.
4 EXT port Connect additional devices (telephone or answering machine) to the printer and the telephone line. Use this port if you do not have a dedicated fax line for the printer and if this connection method is supported in your country or region.
5 LINE port Connect the printer to an active telephone line through a standard wall jack (RJ‑11), DSL filter, or VoIP adapter, or any other adapter that allows you to access the telephone line to send and receive faxes.
6 USB printer port Connect the printer to a computer.
7 Security slot Attach a lock that will secure the printer in place.
Use the To

Additional printer setup 23
1 Close all open software programs.
2 Insert the Software and Documentation CD.
If the installation dialog does not appear after a minute, then launch the CD manually:
, or click Start and then click Run. b In the Start Search or Run dialog, type D:\setup.exe, where D is the letter of your CD or DVD drive.
c Press Enter, or click OK.
3 Click Install, and then follow the instructions on the computer screen.
1 Close all open applications.
2 Insert the Software and Documentation CD.
If the installation dialog does not appear after a minute, then click the CD icon on the desktop.
3 Double-click the software installer package, and then follow the instructions on the computer screen.
1 Go to the Lexmark Web site at http://support.lexmark.com.
2 Navigate to:
SUPPORT & DOWNLOADS > select your printer > select your operating system
3 Download the printer driver, and then install the printer software.
When any hardware options are installed, you may need to manually add the options in the printer driver to make them available for use.
1 Open the printers folder.
, or click Start and then click Run. b In the Start Search or Run dialog, type control printers.
a Click · a Click

Additional printer setup 24
c Press Enter, or click OK.
2 Select the printer.
3 Right‑click the printer, and then select Printer properties (Windows 7) or Properties (earlier versions).
4 Click the Configuration tab.
6 Click Apply.
2 Add any installed hardware options, and then click OK.
To configure your printer to connect to an Ethernet network, organize the following information before you begin:
You will need an Ethernet cable to connect the printer to the network and an available port where the printer can physically connect to the network. Use a new network cable when possible to avoid potential problems caused by a damaged cable.

Additional printer setup 25
1 Insert the Software and Documentation CD.
If the installation dialog does not appear after a minute, then launch the CD manually:
, or click Start and then click Run. b In the Start Search or Run dialog, type D:\setup.exe, where D is the letter of the CD or DVD drive.
c Press Enter, or click OK.
2 Click Install, and then follow the instructions on the computer screen.
3 Select Ethernet connection, and then click Continue.
4 Attach the Ethernet cable when instructed to do so.
5 Select the printer from the list, and then click Continue.
6 Follow the instructions on the computer screen.
1 Allow the network DHCP server to assign an IP address to the printer.
3 Install the printer driver on the computer. a Insert the Software and Documentation CD, and then double‑click the installer package for the printer. b Follow the instructions on the computer screen.
c Select a destination, and then click Continue. d From the Easy Install screen, click Install. e Type the user password, and then click OK.
All the necessary applications are installed on the computer. f Click Close when installation is complete.
4 Add the printer. • For IP printing: a From the Apple menu, navigate to either of the following:
– System Preferences > Print & Scan – System Preferences > Print & Fax b Click +.
c Click the IP tab. d Type the printer IP address in the address field, and then click Add.
a Click

Additional printer setup 26
– Make sure AppleTalk is activated on your printer. – This feature is supported only in Mac OS X version 10.5. a From the Apple menu, navigate to:
System Preferences > Print & Fax b Click +, and then navigate to:
AppleTalk > select your printer > Add
Make sure you have the following information before setting up the printer on a wireless network:
Some ad hoc networks will also require the automatic setting. Check with your system support person if you are not sure which channel to select. • Security Method—There are four basic options for Security Method: – WEP key
If your network uses more than one WEP key, then enter up to four in the provided spaces. Select the key currently in use on the network by selecting the default WEP transmit key. – WPA or WPA2 preshared key or passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network. – 802.1X–RADIUS
If you are installing the printer on an 802.1X network, then you may need the following:
If your wireless network does not use any type of security, then you will not have any security information.
– If you do not know the SSID of the network that your computer is connected to, then launch the wireless utility
of the computer network adapter, and then look for the network name. If you cannot find the SSID or the

Additional printer setup 27
security information for your network, then see the documentation that came with the access point, or contact your system support person. – To find the WPA/WPA2 preshared key or passphrase for the wireless network, see the documentation that
came with the access point, see the Embedded Web Server associated with the access point, or consult your system support person.
Before you begin, make sure that:
> Settings > > Network/Ports > > Active NIC > > Auto >
1 From the printer control panel, navigate to:
> Settings > > Network/Ports > > Network [x] > > Network [x] Setup > > Wireless > >
Wireless Connection Setup >
2 Select a wireless connection setup.
Search for networks Show available wireless connections.
Enter a network name Manually type the SSID.
Wi‑Fi Protected Setup Connect the printer to a wireless network using Wi‑Fi Protected Setup.
3 Press , and then follow the instructions on the printer display.
Before you begin, make sure that:
Use To

Additional printer setup 28
1 From the printer control panel, navigate to:
> Settings > >Network/Ports > > Network [x] > > Network [x] Setup > > Wireless > >
Wi‑Fi Protected Setup > > Start Push Button Method >
2 Follow the instructions on the printer display.
1 From the printer control panel, navigate to:
> Settings > >Network/Ports > > Network [x] > Wireless > > Wi‑Fi Protected Setup > >
Start PIN Method >
2 Copy the eight‑digit WPS PIN.
3 Open a Web browser, and then type the IP address of your access point in the address bar.
4 Access the WPS settings.
5 Enter the eight‑digit PIN, and then save the setting.
Before you begin, make sure that:
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Network/Ports > Wireless.
3 Modify the settings to match the settings of your access point (wireless router).
4 Click Submit.

Additional printer setup 29
5 Turn off the printer, and then disconnect the Ethernet cable. Then wait for at least five seconds, and then turn the printer back on.
6 To verify if your printer is connected to the network, print a network setup page. Then in the Network Card [x] section, see if the status is Connected.
When all hardware and software options are installed and the printer is turned on, verify that the printer is set up correctly by printing the following:
Print a menu settings page to view the current menu settings and to verify if the printer options are installed correctly.
From the printer control panel, navigate to:
> Settings > Reports > > Menu Settings Page >
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the printer control panel, navigate to:
> Settings > Reports > > Network Setup Page >
2 Check the first section of the network setup page, and confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult your system support person for a solution, and then print another network setup page.

Loading paper and specialty media 30
The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 168 and “Storing paper” on page 49.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Paper Size/Type >
2 Press the up or down arrow button to select the tray or feeder, and then press .
3 Press the up or down arrow button to select the paper size, and then press .
4 Press the up or down arrow button to select the paper type, and then press to change the settings.
The Universal paper size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Universal Setup > > Units of Measure > > select a unit of
2 Select Portrait Width or Portrait Height, and then press .
3 Press the left or right arrow button to change the setting, and then press .
1 Pull out the tray completely.
measure >

Loading paper and specialty media 31

2 Squeeze, and then slide the width guide tab to the correct position for the size of the paper you are loading.


EXEC
LTR
A4
A5

Loading paper and specialty media 32
3 Unlock the length guide. Squeeze, and then slide the length guide tab to the correct position for the size of the paper you are loading.


B5
EXEC
LTR
A5

Loading paper and specialty media 33


4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper stack.



Loading paper and specialty media 34


6 Insert the tray.

7 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.

Loading paper and specialty media 35
Use the multipurpose feeder when printing on different paper sizes and types or specialty media, such as card stock, transparencies, paper labels, and envelopes. You can also use it for single‑page print jobs on letterhead.
1 Open the multipurpose feeder.


a Pull the multipurpose feeder extender.


Loading paper and specialty media 36
b Pull the extender gently so that the multipurpose feeder is fully extended and open.

2 Squeeze the tab on the left width guide, and then move the guides for the paper you are loading.

3 Prepare the paper or specialty media for loading. • Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.


Loading paper and specialty media 37
4 Load the paper or specialty media.


Loading paper and specialty media 38






Loading paper and specialty media 39

5 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper or specialty media loaded in the multipurpose feeder.
When one linked tray becomes empty, paper feeds from the next linked tray. We recommended giving all custom paper, such as letterhead and different colored plain papers, a different custom type name so that the trays they are in do not automatically link.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu.
4 Click Submit.

Loading paper and specialty media 40
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Select a custom name, and then type a new custom paper type name.
4 Click Submit.
5 Click Custom Types, and then verify if the new custom paper type name has replaced the custom name.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Custom Names
2 Select a custom name, and then type a new custom paper type name.
3 Press .
4 Press Custom Types, and then verify if the new custom paper type name has replaced the custom name.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Type a name for the paper type, and then click Submit.
4 Select a custom type, and then verify that the correct paper type is associated with the custom name.

Loading paper and specialty media 41
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Custom Names
2 Type a name for the paper type, and then press .
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Types.
3 Select a custom paper type name, and then select a paper type.
4 Click Submit.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Custom Types
2 Select a custom paper type name, and then select a paper type.
3 Press .

Paper and specialty media guide 42
Additional information for printing on speciality media may be found in the Card Stock and Label Guide available at http://support.lexmark.com.
Selecting the correct paper or specialty media reduces printing problems. For the best print quality, try a sample of the paper or specialty media before buying large quantities.
The following paper characteristics affect print quality and reliability. Consider these characteristics when evaluating new paper stock.
The standard printer trays can automatically feed paper weights up to 90‑g/m2 (24‑lb) bond grain long paper. The optional trays can automatically feed paper weights up to 120‑g/m2 (32‑lb) bond grain long paper. The multipurpose feeder can automatically feed paper weights up to 163‑g/m2 (43‑lb) bond grain long paper. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 75‑g/m2 (20‑lb) bond grain long paper. For paper smaller than 182 x 257 mm (7.2 x 10.1 inches), it is recommended to use 90 g/m2
(24 lb) or heavier paper.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.
Paper smoothness directly affects print quality. If paper is too rough, toner cannot fuse to it properly. If paper is too smooth, it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; smoothness between 150–250 Sheffield points produces the best print quality.
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.
Condition paper before printing by storing it in its original wrapper in the same environment as the printer for 24–48 hours before printing. Extend the time to several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.

Paper and specialty media guide 43
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60–90‑g/m2 (16–24‑lb) bond paper, grain long paper is recommended.
Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton can negatively affect paper handling.
The following paper types are not recommended for use with the printer:
Using the appropriate paper prevents jams and helps ensure trouble‑free printing.
To help avoid paper jams and poor print quality:
Use these guidelines when selecting preprinted forms and letterhead:

Paper and specialty media guide 44
Use papers printed with heat‑resistant inks designed for use in xerographic copiers. The ink must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions. Use inks that are not affected by the resin in toner. Inks that are oxidation‑set or oil‑based generally meet these requirements; latex inks might not. When in doubt, contact the paper supplier.
Preprinted papers such as letterhead must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser (electrophotographic) printers. In 1998, Lexmark presented to the US government a study demonstrating that recycled paper produced by major mills in the US fed as well as non-recycled paper. However, no blanket statement can be made that all recycled paper will feed well.
Lexmark consistently tests its printers with recycled paper (20–100% post-consumer waste) and a variety of test paper from around the world, using chamber tests for different temperature and humidity conditions. Lexmark has found no reason to discourage the use of today's recycled office papers, but generally the following property guidelines apply to recycled paper.
Recycled paper, paper of lower weight (

Paper and specialty media guide 45
For information on card stock and labels, see the Card Stock & Label Guide.

250‑sheet tray Optional 250‑ or 550‑sheet tray Multipurpose feeder
A6 105 x 148 mm (4.13 x 5.83 in.)
* To support two‑sided (duplex) printing, the Universal width must be between 76.2 mm (3 in.) and 215.9 mm (8.5 in.); the Universal length must be between 76.2 mm (3 in.) and 359.92 mm (14.17 in.).

Paper and specialty media guide 46

250‑sheet tray Optional 250‑ or 550‑sheet tray Multipurpose feeder
76.2 x 76.2 mm to 215.9 x 359.92 mm (3 x 3 in. to 8.5 x 14.17 in.)
B5 Envelope 176 x 250 mm (6.93 x 9.84 in.)
85.7 x 165 mm to 215.9 x 355.6 mm (3.375 x 6.50 in. to 8.5 x 14 in.)
* To support two‑sided (duplex) printing, the Universal width must be between 76.2 mm (3 in.) and 215.9 mm (8.5 in.); the Universal length must be between 76.2 mm (3 in.) and 359.92 mm (14.17 in.).
The standard tray supports 60–90‑g/m2 (16–24‑lb) paper weights. The optional tray supports 60–120‑g/m2 (16–32‑lb) paper weights. The multipurpose feeder supports 60–163‑g/m2 (16–43‑lb) paper weights.

Paper and specialty media guide 47

Paper type 250‑ or 550‑sheet tray Multipurpose feeder Duplex mode ADF Scanner glass
1 Transparencies are supported only in 250‑sheet tray.
2 One‑sided paper labels designed for laser printers are supported for occasional use. We recommend printing only up to 20 pages of paper labels per month. Vinyl, pharmacy, and two‑sided labels are not supported.
3 Use envelopes that lie flat when individually placed on a table facedown.

Paper and specialty media guide 48
Print samples on the envelopes being considered for use before buying large quantities.
Print samples on the labels being considered for use before buying large quantities.
For more information on label printing, characteristics, and design, see the Card Stock & Label Guide available at http://support.lexmark.com.

Paper and specialty media guide 49
When printing on labels:
releasing hazardous emissions. – Label adhesives, face sheet (printable stock), and topcoats can withstand up to 25‑psi (172‑kPa) pressure without
Card stock is heavy, single‑ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly impact print quality. Print samples on the card stock being considered for use before buying large quantities.
When printing on card stock:
Use these paper storage guidelines to help avoid jams and uneven print quality:

Paper and specialty media guide 50

Printing a document
1 From the Paper menu on the printer control panel, set the paper type and size to match the paper loaded.
2 Send the print job:
a With a document open, click File > Print. b Click Properties, Preferences, Options, or Setup.
c Adjust the settings, if necessary. d Click OK > Print.
a Customize the settings in the Page Setup dialog if necessary:
1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the paper loaded. 3 Click OK. b Customize the settings in the Page Setup dialog if necessary:
1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options. 2 From the Print dialog and pop‑up menus adjust the settings if necessary.
1 Open a Web browser, and then type the IP address of the printer in the address field.
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the toner darkness, and then click Submit.
Printing 51

1 From the printer control panel, navigate to:
> Settings > > Print Settings > > Quality Menu > > Toner Darkness
2 Adjust the toner darkness, and then press .
1 From the printer control panel, navigate to:
> Settings > > Security > > Confidential Print > select the print job type
Print job type Description
Max Invalid PIN Limits the number of times an invalid PIN can be entered.
Confidential Job Expiration Lets you hold print jobs in the computer until you enter the PIN from the printer control panel.
Repeat Job Expiration Lets you print and store print jobs in the printer memory for reprinting.
Verify Job Expiration Lets you print one copy of a print job while the printer holds the remaining copies. It allows you to examine if the first copy is satisfactory. The print job is automatically deleted from the printer memory once all copies are printed.
Reserve Job Expiration Lets you store print jobs for printing at a later time. The print jobs are held until deleted from the Held Jobs menu.
2 Press .
Printing 52

1 With a document open, click File > Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click Print and Hold.
4 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
5 Click OK or Print.
1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2 From the print options or Copies & Pages pop‑up menu, choose Job Routing.
3 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
4 Click OK or Print.
1 Open a Web browser, and then type the printer IP address in the address field.
Printing 53

2 Click Configuration > Other Settings tab > Security > Confidential Print Setup.
4 Save the modified settings.
1 From the printer control panel, navigate to:
> Settings > > Reports > > Print Fonts
2 Press the up or down arrow button to select the font setting.
3 Press .
From the printer control panel, press
. When a list of print jobs appears, select the job to cancel, and then
press .
1 Open the printers folder.
, or click Start and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
2 Double‑click the printer icon.
Printing 54 · a Click

3 Select the print job you want to cancel.
4 Click Delete.
2 From the printer window, select the print job you want to cancel, and then click Delete.
Printing 55

Automatic document feeder (ADF) Scanner glass
Use the ADF for multiple‑page documents including two-sided (duplex) pages.
Use the scanner glass for single-page documents, book pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, press .
1 Load an original document faceup, short edge first into the ADF tray.
Copying 56

2 Adjust the paper guides.
3 From the printer control panel, use the keypad to enter the number of copies, and then press .
1 Place an original document facedown on the scanner glass in the upper left corner.
2 From the printer control panel, use the keypad to enter the number of copies, and then press .
or right arrow button to scroll to Scan the Next Page, and then press .
3 Press the left or right arrow button to scroll to Finish the Job, and then press .
1 Place a photo facedown on the scanner glass in the upper left corner.
2 From the printer control panel, navigate to:
> Copy > > Content Type > Photo
3 From the Content Source menu, choose a setting that best describes the original photo your are copying, and then
press .
to scroll to Scan the Next Page, and then press .
4 Press the left or right arrow button to scroll to Finish the Job, and then press .
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
Copying 57

3 From the printer control panel, navigate to:
> Copy > > Copy from > select the size of the original document
4 Navigate to:
Copy to > > select the tray containing the transparencies > > select the number of copies or enter a
number on the keypad >
5 If there are no trays that contain transparencies, then do the following: a Navigate to:
Copy to > > Manual Feeder > > select the size of the transparencies > > Transparency >
b Load transparencies into the multipurpose feeder, and then press .
button to scroll to Scan the Next Page, and then press .
6 Press the left or right arrow button to scroll to Finish the Job, and then press .
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Copy > > Copy from > select the size of the original document
4 Navigate to:
Copy to > > select the tray containing the letterhead > > select the number of copies or enter a number
on the keypad >
Copying 58

5 If there are no trays that contain letterhead, then do the following: a Navigate to:
Copy to > > Manual Feeder > > select the size of the letterhead > Letterhead
b Place the letterhead faceup, top edge first into the multipurpose feeder, and then press .
button to scroll to Scan the Next Page, and then press .
6 Press the left or right arrow button to scroll to Finish the Job, and then press .
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Copy > > Copy from > select the size of the original document
4 Navigate to:
Copy to > > select a new size for the copy > select the number of copies or enter a number on the keypad >
button to scroll to Scan the Next Page, and then press .
5 Press the left or right arrow button to scroll to Finish the Job, and then press .
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
Copying 59

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Copy > > Copy from > select the size of the original document
4 Navigate to:
Copy to > > select the tray containing the paper size and type you want to use > > select the number of
copies or enter a number on the keypad >
5 If there are no trays that contain the paper size and type you want to use, then do the following: a Navigate to:
Copy to > > Manual Feeder > > select the paper size > > select the paper type >
b Load the size and type of paper into the multipurpose feeder, and then press .
to scroll to Scan the Next Page, and then press .
6 Press the left or right arrow button to scroll to Finish the Job, and then press .
1 Load a document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Copy > > Sides (Duplex) > select a duplex option > select the number of copies or enter a number on
button to scroll to Scan the Next Page, and then press .
4 Press the left or right arrow button to scroll to Finish the Job, and then press .
Copying 60 · the keypad >

Copies can be scaled from 25% to 400% of the original document size.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Copy > > Scale > adjust the scale setting > select the number of copies or enter a number on the keypad >
button to scroll to Scan the Next Page, and then press .
4 Press the left or right arrow button to scroll to Finish the Job, and then press .
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass in the upper left corner.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Copy > > Darkness > adjust the darkness setting > select the number of copies or enter a number on
button to scroll to Scan the Next Page, and then press .
4 Press the left or right arrow button to scroll to Finish the Job, and then press .
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
Copying 61 · the keypad >

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Copy > > Content Type > select the content type of the original document
5 Press the up or down arrow button until Content Source appears, and then press the left or right arrow button to scroll to one of the following:
6 Select the number of copies or enter a number on the keypad, and then press .
button to scroll to Scan the Next Page, and then press .
7 Press the left or right arrow button to scroll to Finish the Job, and then press .
If you print multiple copies of a document, then you can choose to print each copy as a set (collated) or to print the copies as groups of pages (not collated).
Copying 62 · Collated Not collated

To select a Collate setting:
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Copy > > Collate > select the collate setting you want > select the number of copies or enter a number
on the keypad >
button to scroll to Scan the Next Page, and then press .
4 Press the left or right arrow button to scroll to Finish the Job, and then press .
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Copy > > Separator Sheets
4 Select Between Copies, Between Jobs, Between Pages, or Off.
5 Select the number of copies or enter a number on the keypad, and then press .
button to scroll to Scan the Next Page, and then press .
6 Press the left or right arrow button to scroll to Finish the Job, and then press .
To save paper, you can copy either two or four consecutive pages of a multiple‑page document onto a single sheet of paper.
Copying 63

1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Copy > > Paper Saver > select the setting that you want
4 Select Off, 2‑up Portrait, 2‑up Landscape, 4‑up Portrait, or 4‑up Landscape.
5 Select the number of copies or enter a number on the keypad, and then press .
button to scroll to Scan the Next Page, and then press .
6 Press the left or right arrow button to scroll to Finish the Job, and then press .
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Copy > > Overlay > select an overlay message you want
4 Select Off, Confidential, Copy, Draft, Urgent, or Custom.
Copying 64

5 Select the number of copies or enter a number on the keypad, and then press .
button to scroll to Scan the Next Page, and then press .
6 Press the left or right arrow button to scroll to Finish the Job, and then press .
From the printer control panel, press
This option lets you set the number of copies to be printed.
This option opens a screen where you can select the paper size of the original document.
. • To copy an original document that contains mixed paper sizes with the same width, press the left or right arrow
button to scroll to Mixed Sizes, and then press . • To set the printer to automatically detect the size of the original document, press the left or right arrow button to
scroll to Auto Size Sense, and then press .
This option lets you select the paper size and type on which your copies will be printed.
button, and then press . • If the settings for “Copy from” and “Copy to” are different, then the printer automatically adjusts the Scale setting to accommodate the difference.
Copying 65

to scroll to Manual Feeder, press , and then manually load the paper in the manual feeder or multipurpose feeder. • To match each copy to the paper size of the original document, set “Copy to” to Auto Size Match. If a matching paper size is not in one of the trays, then Paper size not found appears and prompts to load a paper in a tray, manual feeder, or multipurpose feeder.
This option lets you scale the document from 25% to 400% of the original document size. You can also set automatic scaling.
This option lets you adjust how light or dark the copies are in relation to the original document.
This option lets you make one- or two-sided copies from one- or two-sided original documents.
This option keeps the pages of a print job stacked in sequence when printing multiple copies of the document.
This option lets you set the original document type.
Select from the following content types:
This option lets you set the original document source.
Select from the following content sources:
Copying 66

This option lets you specify the document orientation, whether documents are one-sided or two-sided, and how documents are bound.
This option lets you create a watermark (or message) that overlays the content of your copy. You can choose from Confidential, Copy, Draft, Urgent, and Custom. You can type a custom message in the ”Enter the Custom Text Overlay and press OK” field. The message will appear, faintly, in large print across each page.
This option lets you place a blank sheet of paper between copies, prints, pages, print jobs or copy jobs. The separator sheets can be drawn from a tray that contains a type or color of paper that is different from the paper your copies are printed on.
This option lets you print two or more pages of an original document on the same page. Paper Saver is also called N- up printing where N stands for the number of pages. For example, 2-up would print two pages of your document on a single page, and 4-up would print four pages of your document on a single page.
Copying 67

Automatic document feeder (ADF) Scanner glass
Use the ADF for multiple‑page documents including two-sided (duplex) pages.
Use the scanner glass for single-page documents, book pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
You can use the printer to e‑mail scanned documents to one or more recipients. There are three ways to send an e‑mail from the printer. You can type the e‑mail address, use a shortcut number, or use the address book.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > E-mail/FTP Settings > E-mail Settings.
3 Enter the appropriate information, and then click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
E-mailing 68

2 Click Settings > E-mail/FTP Settings > E-mail Settings.
3 Enter the appropriate information, and then click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Manage Shortcuts > E-mail Shortcut Setup.
3 Type a name for the shortcut, and then enter the e-mail address.
4 Adjust the scan settings, if necessary.
5 Enter a shortcut number, and then click Add.
If you enter a number that is already in use, then you are prompted to select another number.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 Press #, then enter the shortcut number using the keypad, and then press .
4 Press .
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
E-mailing 69

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> E-mail Shortcuts > > select the name of the recipient >
From the printer control panel, press
E-mailing 70

Automatic document feeder (ADF) Scanner glass
Use the ADF for multiple‑page documents including two-sided (duplex) pages.
Use the scanner glass for single-page documents, book pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).

Faxing 71

Many countries and regions require outgoing faxes to contain the following information in a margin at the top or bottom of each transmitted page, or on the first page of the transmission: fax name (identification of the business, other entity, or individual sending the message) and fax number (telephone number of the sending fax machine, business, other entity, or individual).
To enter your fax setup information, use the printer control panel, or use your browser to access the Embedded Web Server, and then open the Settings menu.
When the printer is turned on for the first time, a series of start‑up screens appear. If the printer has fax capabilities, then the Fax Name or Station Name and Fax Number or Station Number screens appear:
1 When Fax Name or Station Name appears, type the name to be printed on all outgoing faxes, and then press
2 When Fax Number or Station Number appears, enter the printer fax number, and then press .
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Fax Settings > Analog Fax Setup.
3 In the Fax Settings menu, type the name to be printed on all outgoing faxes in the Fax Name or Station Name field.
4 In the Fax Number or Station Number field, enter the printer fax number.
5 Click Submit.
Faxing 72

Setup 1: Printer is connected to a dedicated fax line


To connect:
1 Connect one end of the telephone cable that came with the printer to the port of the printer.
2 Connect the other end of the telephone cable to an active analog wall jack.
Faxing 73

Connected to the same telephone wall jack

To connect:
1 Connect one end of the telephone cable that came with the printer to the port of the printer.
2 Connect the other end of the telephone cable to an active analog wall jack.
3 Connect the answering machine to the port of the printer.
Faxing 74

Connected to different wall jacks

To connect:
1 Connect one end of the telephone cable that came with the printer to the port of the printer.
2 Connect the other end of the telephone cable to an active analog wall jack.
Faxing 75


To connect:
1 Connect one end of the telephone cable that came with the printer to the port of the printer.
2 Connect the other end of the telephone cable to an active analog wall jack.
3 Connect the telephone to the port of the printer.
When you answer the telephone and you hear fax tones, press *9* or the manual answer code on the telephone to receive the fax. • You can also set the printer to receive faxes automatically (Auto Answer On), but you need to turn off the voice mail service when you are expecting a fax. This setting works best if you are using voice mail more often than fax.
Faxing 76


A Digital Subscriber Line splits your regular telephone line into two channels: voice and Internet. Telephone and fax signals travel through the voice channel, and Internet signals pass through the other channel. This way, you can use the same line for analog voice calls (including faxes) and digital Internet access.
To minimize interference between the two channels and ensure a quality connection, you need to install a DSL filter for the analog devices (fax machine, telephone, answering machine) in your network. Interference causes noise and static on the telephone, failed and poor quality faxes for the printer, and slow Internet connection on your computer.
To install a filter for the printer:
1 Connect the line port of the DSL filter to the wall jack.
2 Connect one end of the telephone cable that came with your printer to the port of the printer. Connect the other end to the phone port on the DSL filter.
3 To continue using a computer for Internet access, connect the computer to the DSL HPN port on the DSL filter.
4 To connect a telephone to the printer, remove any installed adapter plug from the port of the printer, and then connect the telephone to the port.
Faxing 77



To connect:
1 Connect one end of the telephone cable that came with the printer to the port of the printer.
2 Connect the other end of the cable to the port labeled Phone Line 1 or Phone Port on the VoIP adapter.
3 Connect the telephone to the port of the printer.
Faxing 78

Setup 1: Printer is connected directly to a cable modem

1 Connect one end of the telephone cable that came with your printer to the port of the printer.
2 Connect the other end of the cable to the port labeled Phone Line 1 or Phone Port on the cable modem.
3 Connect your analog telephone phone to the port of the printer.
Faxing 79

Setup 2: Printer is connected to a wall jack; cable modem is installed elsewhere in the facility

1 Connect one end of the telephone cable that came with your printer to the port of the printer.
2 Connect the other end of the telephone cable to an active analog telephone wall jack.
3 Connect your analog telephone to the port of the printer.
Some countries or regions may have different types of telephone wall jack connectors than those that came with the printer. The standard wall jack adopted by most countries or regions is RJ-11. Your printer comes with the RJ-11 jack and a telephone cable with the RJ-11 plug.
Faxing 80

If the wall jack or equipment in your facility is not compatible with this type of connection, then you need to use a telephone adapter. An adapter for your country or region may not come with your printer, and you may need to purchase it separately.
There may be an adapter plug installed in the port of the printer. If you are using a telephone adapter or a facility that has a cascaded or serial wiring scheme, then do not remove the adapter plug from the port of the printer.
Part name Part number
Lexmark adapter plug 40X8519
Faxing 81

Connecting the printer to a non‑RJ‑11 wall jack

1 Connect one end of the telephone cable that came with printer to the port of the printer.
2 Connect the other end of the cable to the RJ‑11 adapter, and then connect the adapter to the wall jack.
3 If you want to connect another device (telephone or answering machine) to the same wall jack, and if the device has a non‑RJ‑11 connector, then connect it directly to the telephone adapter.
Faxing 82

The German wall jack has two kinds of ports. The N ports are for fax machines, modems, and answering machines. The F port is for telephones.

Connect the printer to any of the N ports.

Faxing 83

1 Connect one end of the telephone cable that came the printer to the port of the printer.
2 Connect the other end of the telephone cable to the RJ‑11 adapter, and then connect the adapter to an N port.
3 If you want to connect a telephone and answering machine to the same wall jack, then connect the devices as shown.
A distinctive ring service may be available from your telephone company. This service lets you have multiple telephone numbers on one telephone line, with each telephone number having a different ring pattern. This may be useful for distinguishing between fax and voice calls. If you subscribe to a distinctive ring service, then follow these steps to connect the equipment:
1 Connect one end of the telephone cable that came with the printer to the printer LINE port .
2 Connect the other end of the telephone cable to an active analog telephone wall jack.

3 Change the Distinctive Rings setting to match the setting you want the printer to answer.
From the printer control panel, navigate to:
> Settings > > Fax Settings > > Distinctive Rings > select the ring tone you want >
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Fax Settings > Analog Fax Setup.
3 From the Fax Settings menu, type the name to be printed on all outgoing faxes in the Fax Name or Station Name field.
4 In the Fax Number or Station Number field, enter the printer fax number.
5 Click Submit.
Faxing 84

You can set the date and time so that they are printed on every fax you send. If there is a power failure, then you may have to reset the date and time.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Other Settings area > Security > Set Date and Time.
3 In the Set Date & Time field, enter the current date and time.
4 Click Submit.
Set the printer to automatically adjust for daylight saving time.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Security > Set Date and Time.
3 Select the Automatically Observe DST check box, and then enter the DST start and end dates in the Custom Time Zone Setup section.
4 Click Submit.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
Faxing 85

3 From the printer control panel, navigate to:
> Fax > > enter a fax or shortcut number on the keypad > > Original Size >
button to scroll to Scan the Next Page, and then press .
4 Press the left or right arrow button to scroll to Finish the Job, and then press .
The printer driver fax option lets you send a print job to the printer, which sends the job as a fax. The fax option works as a normal fax machine, but is controlled through the printer driver instead of the printer control panel.
1 With a document open, click File > Print.
2 Select the printer, and then navigate to:
Properties > Fax tab > Enable fax
3 Enter the recipient fax number or numbers in the “Fax number(s)” field.
4 If necessary, enter a prefix in the “Dialing prefix” field.
5 Select the appropriate paper size and page orientation.
6 If you want to include a cover page with the fax, then select Include cover page with fax, and then enter the appropriate information.
7 Click OK.
Fax shortcuts are just like the speed dial numbers on a telephone or fax machine. A shortcut number (1–999) can contain a single recipient or multiple recipients.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
Faxing 86

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 Press #, and then enter the shortcut number on the keypad.
4 Press .
The address book feature lets you search for bookmarks and network directory servers.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Fax select the name of the recipient >
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Fax > > enter the fax number > Delayed Send > Send Later > select the date you want the fax to be
sent > > select the time you want the fax to be sent >
4 Press .
Assign a shortcut number to a single fax number or a group of fax numbers.
1 Open a Web browser, and then type the printer IP address in the address field.
Faxing 87

2 Click Settings > Manage Shortcuts > Fax Shortcut Setup.
3 Type a name for the shortcut, and then enter the fax number.
4 Assign a shortcut number.
5 Click Add.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> Fax > > enter the fax number > Resolution > select the resolution you want
4 Press .
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
Faxing 88

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
Fax > > enter the fax number > > Darkness > adjust the darkness of the fax >
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Reports.
3 Click Fax Job Log or Fax Call Log.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Fax Settings > Analog Fax Setup > Block No Name Fax.
. • If you are using the scanner glass and Scanning page, Scan the Next Page, or Finish the Job
Faxing 89 · appears, then press

1 From the printer control panel, press
2 Press the left or right arrow button to scroll to the job you want to cancel.
3 Press > Delete Selected Jobs.
This option lets you hold received faxes from printing until they are released. Held faxes can be released manually or at a scheduled day or time.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Fax Settings > Analog Fax Setup > Holding Faxes.
3 From the Held Fax Mode menu, select Off, Always On, Manual, or Scheduled.
4 If you selected Scheduled, then continue with the following steps: a Click Fax Holding Schedule. b From the Action menu, select Hold faxes.
c From the Time menu, select the time you want the held faxes released. d From the Day(s) menu, select the day you want the held faxes released.
5 Click Add.
This option lets you print and forward received faxes to a fax number, e‑mail address, FTP site, or LDSS.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Fax Settings.
3 From the Fax Forwarding menu, select Print, Print and Forward, or Forward.
4 From the “Forward to” menu, select Fax, E‑mail, FTP, LDSS, or eSF.
Faxing 90

5 In the “Forward to Shortcut” field, enter the shortcut number where you want the fax forwarded.
6 Click Submit.
This option lets you choose the size of the documents you are going to fax.
1 From the Fax area of the printer control panel, press the Options button.
Original Size appears.
2 Press .
3 Press the arrow buttons until the size of the original document appears, and then press .
This option lets you adjust the quality of the fax output. Increasing the image resolution increases the file size and the time needed to scan your original document. Decreasing the image resolution reduces the file size.
Select one of the following:
This option lets you adjust how light or dark the faxes are in relation to the original document.
This option lets you set the original document type.
Select from the following content types:
Faxing 91

This option lets you set the original document source.
Select from the following content sources:
This option informs the printer if the original document is simplex (printed on one side) or duplex (printed on both sides). This lets the scanner know what needs to be scanned for inclusion in the fax.
This option lets you specify the orientation of the original document, and then change the Sides and Binding settings to match the orientation.
This option lets you specify if the original document is bound on the long‑edge or short‑edge side.
Faxing 92

Scanning to an FTP address
Automatic document feeder (ADF) Scanner glass
Use the ADF for multiple‑page documents including two-sided (duplex) pages.
Use the scanner glass for single-page documents, book pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
The scanner lets you scan documents directly to a File Transfer Protocol (FTP) server. Only one FTP address may be sent to the server at a time.
When an FTP destination has been configured by your system support person, the name of the destination becomes available as a shortcut number, or it is listed as a profile under the Held Jobs icon. An FTP destination could also be another PostScript printer.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Navigate to:
Settings > Other Settings area > Manage Shortcuts > FTP Shortcut Setup
3 Enter the appropriate information.
Scanning 93

4 Enter a shortcut number.
If you enter a number that is already in use, then you are prompted to select another number.
5 Click Add.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, press #, and then enter the FTP shortcut number.
4 Press .
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, navigate to:
> FTP Shortcuts > > select the name of the recipient >
Scanning 94

Automatic document feeder (ADF) Scanner glass
Use the ADF for multiple‑page documents. Use the scanner glass for single pages, small items (such as postcards or
photos), transparencies, photo paper, or thin media (such as magazine clippings).
The scanner lets you scan documents directly to a computer. The computer does not have to be directly connected to the printer for you to receive Scan to PC images. You can scan the document back to the computer over the network by creating a scan profile on the computer and then downloading the profile to the printer.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Scan Profile > Create Scan Profile.
3 Select your scan settings, and then click Next.
4 Select a location on your computer where you want to save the scanned output file.
5 Type a scan name.
The scan name is the name that appears in the Scan Profile list on the display.
6 Click Submit.
7 Review the instructions on the Scan Profile screen.
A shortcut number is automatically assigned when you click Submit. You can use this shortcut number when you are ready to scan your documents.
a Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
Scanning 95

c From the printer control panel, press #, and then type the shortcut number using the keypad, or press the up or down arrow button to scroll to Held Jobs, and then press the up or down arrow button to scroll to Profiles. After entering the shortcut number, the scanner scans and sends the document to the directory or program you specified. If you selected Profiles on the printer control panel, then locate your shortcut on the list.
8 View the file from the computer.
The output file is saved in the location or launched in the program you specified.
Scanning 96

Understanding printer menus 97
Menus list
Paper Menu Reports Network/Ports Security Settings
Network Setup Page1
Set Date and Time
E‑mail Settings
Fax Call Log Copy Shortcuts
Print Defects Guide Information Guide
1 Depending on the printer setup, this menu item appears as Network Setup Page or Network [x] Setup Page.
2 Depending on the printer setup, this menu item appears as Standard Network or Network [x].

Understanding printer menus 98
Set a default paper source for all print jobs.
Tray [x] MP Feeder Manual Paper Manual Envelope
Specify the size of the paper loaded in each tray.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the type of the paper loaded in each tray.
Plain Paper Transparency Recycled Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]

Understanding printer menus 99
Specify the size of the paper loaded in the multipurpose feeder.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the type of the paper loaded in the multipurpose feeder.
Plain Paper Card Stock Transparency Recycled Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Use To · MP Feeder Size · MP Feeder Type

Understanding printer menus 100
Specify the size of the paper being manually loaded.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the type of the paper being manually loaded.
Plain Paper Card Stock Transparency Recycled Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Specify the size of the envelope being manually loaded.
7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the type of the envelope being manually loaded.
Envelope Rough Envelope Custom Type [x]

Understanding printer menus 101
Determine when the printer selects paper from the multipurpose feeder.
Substitute a specified paper size if the requested paper size is not available.
Off Statement/A5 Letter/A4 All Listed
Specify the relative texture of the plain paper loaded.
Specify the relative texture of the card stock loaded.
Specify the relative texture of the transparencies loaded.
Specify the relative texture of the recycled paper loaded.

Understanding printer menus 102
Specify the relative texture of the labels loaded.
Specify the relative texture of the bond paper loaded.
Specify the relative texture of the envelopes loaded.
Specify the relative texture of the rough envelopes loaded.
Specify the relative texture of the letterhead loaded.
Specify the relative texture of the preprinted paper loaded.
Specify the relative texture of the colored paper loaded.
Specify the relative texture of the paper loaded.
Specify the relative texture of the paper loaded.
Specify the relative texture of the cotton paper loaded.
Specify the relative texture of the custom paper loaded.

Understanding printer menus 103
Specify the relative weight of the plain paper loaded.
Specify the relative weight of the card stock loaded.
Specify the relative weight of the transparencies loaded.
Specify the relative weight of the recycled paper loaded.
Specify the relative weight of the labels loaded.
Specify the relative weight of the bond paper loaded.
Specify the relative weight of the envelope loaded.
Specify the relative weight of the rough envelope loaded.
Specify the relative weight of the letterhead loaded.
Specify the relative weight of the preprinted paper loaded.

Understanding printer menus 104
Specify the relative weight of the colored paper loaded.
Specify that the relative weight of the paper loaded is light.
Specify the relative weight of the paper loaded is heavy.
Specify the relative weight of the cotton or rough paper loaded.
Specify the relative weight of the custom paper loaded.
Determine and set two‑sided printing for all print jobs that specify Recycled as the paper type.
Determine and set two‑sided printing for all print jobs that specify Bond as the paper type.
Determine and set two‑sided printing for all print jobs that specify Letterhead as the paper type.
Determine and set two‑sided printing for all print jobs that specify Preprinted as the paper type.
Determine and set two‑sided printing for all print jobs that specify Colored as the paper type.

Understanding printer menus 105
Determine and set two‑sided printing for all print jobs that specify Light as the paper type.
Determine and set two‑sided printing for all print jobs that specify Heavy as the paper type.
Determine and set two‑sided printing for all print jobs that specify Custom [x] as the paper type.
Associate a paper or specialty media type with a factory default Custom Type [x] name or a user‑defined custom name created in the Embedded Web Server or MarkVisionTM Professional. The user‑defined name appears instead of Custom Type [x].
Paper Card Stock Transparency Rough/Cotton Labels Envelope
Specify a paper type when the Recycled setting is selected in other menus.
Paper Card Stock Transparency Rough/Cotton Labels Envelope Cotton

Understanding printer menus 106
Custom Scan Size [x]
Specify a custom scan size name and page orientation.
Scan Size Name Width Height Orientation
Portrait Landscape 2 scans per side Off On
Identify the units of measure.
Set the portrait width.
3–8.5 inches 76–216 mm
Set the portrait height.
3–14.17 inches 76–360 mm

Understanding printer menus 107
Specify the feed direction if the paper can be loaded in either direction.
Short Edge Long Edge
Menu Settings Page Print a report containing information about the paper loaded into trays, installed memory, total page count, alarms, timeouts, printer control panel language, TCP/IP address, status of supplies, status of the network connection, and other information.
Device Statistics Print a report containing printer statistics such as supply information and details about printed pages.
Network Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address information.
Shortcut List Print a report containing information about configured shortcuts.
Fax Job Log Print a report containing information about the last 200 completed faxes.
Fax Call Log Print a report containing information about the last 100 attempted, received, and blocked calls.
Copy Shortcuts Print a report containing information about copy shortcuts.
E‑mail Shortcuts Print a report containing information about e‑mail shortcuts.
Fax Shortcuts Print a report containing information about fax shortcuts.
FTP Shortcuts Print a report containing information about FTP shortcuts.
Profiles List Print a list of profiles stored in the printer.
Print Fonts Print a report of all the fonts available for the printer language currently set in the printer.
Asset Report Print a report containing asset information including the printer serial number and model name. The report contains text and UPC bar codes that can be scanned into an asset database.
Use To · Feed Direction · Use To
![Page 108 of the Lexmark MX310 user manual — Standard Network or Network [x] menu](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-108.webp?w=400)
Understanding printer menus 108
Auto [list of available network cards]
Set the printer to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.

Understanding printer menus 109
Set the size of the network input buffer.
Auto 3KB to [maximum size allowed]
Set the printer to process Macintosh binary PostScript print jobs.
Standard Network Setup or Network [x] Setup
Display and set the printer network settings.
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
To access the menu, navigate to either of the following:
Print Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address.
To access the menu, navigate to either of the following:

Understanding printer menus 110
View the connection status of the network card.
View Card Speed View the speed of an active network card.
View the network addresses.
Set the amount of time it takes for a network print job to be canceled.
To access the menu, navigate to either of the following:
Set Hostname Set the current TCP/IP host name.
IP Address View or change the current TCP/IP address.
Netmask View or change the current TCP/IP netmask.
Gateway View or change the current TCP/IP gateway.
Specify the DHCP address and parameter assignment.
Specify the RARP address assignment setting.
Specify the BOOTP address assignment setting.

Understanding printer menus 111
Specify the Zero Configuration Networking setting.
Enable the built-in FTP server, which lets you send files to the printer using File Transfer Protocol.
Enable the built-in Web server (Embedded Web Server). When enabled, the printer can be monitored and managed remotely using a Web browser.
WINS Server Address View or change the current WINS server address.
View or change the current DDNS setting.
View or change the current mDNS setting.
DNS Server Address View or change the current DNS server address.
Backup DNS Server Address View or change the backup DNS server addresses.
Backup DNS Server Address 2
Backup DNS Server Address 3
View or change the current HTTPS setting.
To access the menu, navigate to either of the following:
Enable IPv6 in the printer.
Specify whether or not the wireless network adapter accepts the automatic IPv6 address configuration entries provided by a router.

Understanding printer menus 112
View Hostname Set the host name.
Enable DHCPv6 in the printer.
To access the menu, navigate to either of the following:
Wi‑Fi Protected Setup (WPS)
Establish a wireless network connection and enable network security.
Start Push Button Method Start PIN Method
Enable/Disable WPS Auto‑detection
Automatically detect the connection method that an access point with WPS uses—Start Push Button Method or Start PIN Method.
Specify the network mode.
Specify the wireless standard for the wireless network.
802.11b/g 802.11b/g/n
Choose Network Select an available network for the printer to use.
View Signal Quality View the quality of the wireless connection.
View Security Mode View the encryption method for the wireless network.

Understanding printer menus 113
To access the menu, navigate to any of the following:
Enable or disable AppleTalk support.
View Name Show the assigned AppleTalk name.
View Address Show the assigned AppleTalk address.
Provide a list of AppleTalk zones available on the network.
[list of zones available on the network]
Primary SMTP Gateway Specify SMTP server gateway and port information.
Secondary SMTP Gateway Port
5–30 Specify the amount of time in seconds before the server stops trying to send an e‑mail.
Reply Address Specify a reply address of up to 128 characters in the e-mail sent by the printer.
Set the printer to use SSL for increased security when connecting to the SMTP server.

Understanding printer menus 114
Specify the type of user authentication required for scan to e‑mail privileges.
No authentication required Login/Plain CRAM‑MD5 Digest‑MD5 NTLM Kerberos 5
Device‑Initiated E‑mail
Specify what credentials will be used when communicating to the SMTP server.
None Use Device SMTP Credentials
Export Log Let an authorized user export the audit log.
Specify whether or not audit logs are deleted.
Specify how and whether or not audit logs are created.
Yes No Enable Remote Syslog
No Yes Remote Syslog Facility
0–23 Severity of events to log

Understanding printer menus 115
Current Date and Time View the current date and time settings for the printer.
Manually Set Date and Time
Enter the date and time.
Select the time zone.
[list of time zones]
Set the printer to use the applicable daylight saving time (DST) start and end times associated with the printer Time Zone setting.
Enable Network Time Protocol, which synchronizes the clocks of devices on a network.

Understanding printer menus 116
Set the language of the text appearing on the printer display.
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portuguese Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese
Display the estimates of the supplies on the printer control panel, Web page, menu settings, and the device statistics reports.
Show estimates Do not show estimates
Minimize the use of energy, paper, or specialty media.
Off Energy Energy/Paper Paper
Specify whether or not the ADF sounds a beep when paper is loaded.

Understanding printer menus 117
Run the setup wizard.
Specify the unit of measurement for paper sizes.
Scan to PC Port Range
Specify a valid port range for printers behind a port blocking firewall. The valid ports are specified by two sets of numbers separated by a semicolon.
Change the icons and buttons that appear on the printer display.
Change Language Copy Fax Fax shortcuts E‑mail shortcuts FTP shortcuts Search held jobs Held jobs Bookmarks Jobs by user
For each icon or button, select from the following options:
Display Do not display
Set copies from the printer to only one page at a time.
Specify whether image background removal is allowed in copy, and fax jobs.
Allow Custom Job Scans
Scan multiple jobs to one file.
Specify how a scan job should be reloaded if a paper jam occurs in the ADF.
Job Level page Level

Understanding printer menus 118
Set an alarm to sound when the printer requires user intervention. When activated, Alarm Control lets you set the number of times that the alarm sounds, while Cartridge Alarm lets you stop printing when a cartridge‑low condition occurs.
Alarm Control Cartridge Alarm
For each alarm type, select from the following options:
Set the amount of time the printer waits after a job is printed before it goes into a reduced power state.
Set the amount of time the printer waits before it goes to Hibernate mode.
Disabled 1 hour 2 hours 3 hours 6 hours 1 day 2 days 3 days 1 week 2 weeks 1 month
Set the printer to hibernate mode when there is an active Ethernet connection.
Hibernate Timeout on Connection
Hibernate Do Not Hibernate

Understanding printer menus 119
Set the amount of time in seconds the printer waits before returning the display to the Ready state.
Set the amount of time in seconds the printer waits to receive an end‑of‑job message before canceling the remainder of the print job.
Set the amount of time in seconds the printer waits for additional data before canceling a print job.
Automatically reboot the printer back into the normal operation.
Reboot when idle Reboot always Reboot never
Determine the number of automatic reboots the printer can perform.
Let the printer automatically continue printing from certain offline situations when these are not resolved within the specified time period.
Specify whether the printer reprints jammed pages.

Understanding printer menus 120
Set the printer to automatically check for jammed paper.
Let the printer successfully print a page that may not have printed otherwise.
Determine how the printer, while in idle state, reacts to a short press of the Sleep button.
Do nothing Sleep Hibernate
Press and Hold Sleep Button
Determine how the printer, while in idle state, reacts to a long press of the Sleep button.
Do nothing Sleep Hibernate
Return the printer settings to the factory default settings.
Do Not Restore Restore Now
Create a custom home message that appears during warnings, printer errors and the Home Prime/Status state.
Off IP Address Hostname Contact Name Location Zero Configuration Name Custom Text [x]

Understanding printer menus 121
Specify the content of the original document.
Text Graphics Text/Photo Photo
Specify how the original document was produced.
Black/White Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify whether an original document is two‑sided (duplex) or one‑sided, and then specify whether the copy should be two‑sided or one‑sided.
1 sided to 1 sided 1 sided to 2 sided 2 sided to 1 sided 2 sided to 2 sided
Copy two or four sheets of a document on one page.
Off 2‑up Portrait 2‑up Landscape 4‑up Portrait 4‑up Landscape
Specify whether or not a border is printed.
Keep the pages of a print job stacked in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)

Understanding printer menus 122
Specify the paper size of the original document.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense A4 A5 A6 JIS B5 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in. ID Card
Specify the paper source for copy jobs.
Tray [x] Auto Size Match Manual Feeder
Place a sheet of paper between transparencies.
Place a sheet of paper between pages, copies, or jobs.
Off Between Copies Between Jobs Between Pages
Specify the separator sheet source.
1–9 Lighten or darken the print on the copy.
1–999 Specify the number of copies for the copy job.

Understanding printer menus 123
Specify the overlay text printed on each page of the copy job.
Confidential Copy Draft Urgent Custom Off
Allow interruption of a print job to copy a page or document.
Allow Save as Shortcut
Save custom copy settings as shortcuts.
Adjust the amount of background visible on a copy.
‑4 to 4
Automatically align the content at the center of the page.
Specify the contrast used for the copy job.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a copy.
‑4 to 4
Correct slight skew in the scanned image.
Specify if the original document is scanned edge‑to‑edge.
Scan edge to edge
1–5 Adjust the amount of sharpness of a copy.
Create a sample copy of the original document.

Understanding printer menus 124
Analog Fax Setup mode sends the fax job through a telephone line.
Fax Name Specify the name of the fax in the printer.
Fax Number Specify the number assigned to the fax.
Specify how the fax is identified.
Fax Name Fax Number
Set the printer to fax manually, which requires a line splitter and a telephone handset.
Define the allocation of non-volatile memory between sending and receiving fax jobs.
All receive Mostly receive Equal Mostly send All send
Specify whether or not the printer cancels fax jobs.
Specify the type of caller ID being used.
Specify the direction from where digits are masked in an outgoing fax number.
Off From left From right
0–58 Specify the number of digits to mask in an outgoing fax number.

Understanding printer menus 125
Configure the fax cover page.
Off by default On by default Never use Always use Include to Field
On Off Include from Field
On Off Include Message Field
On Off Include Logo
Specify quality in dots per inch (dpi). A higher resolution gives better print quality, but increases the fax transmission time for outgoing faxes.
Standard Fine 200 dpi Super Fine 300 dpi
Specify the paper size of the original document.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in.

Understanding printer menus 126
Specify the content of the original document.
Text Graphics Text/Photo Photo
Specify how the original document was produced.
Black/White Laser Inkjet Photo/Film Magazine Newspaper Press Other
1–9 Lighten or darken the output.
Dial Prefix Enter a dialing prefix, such as 99. A numeric entry field is provided.
0–9 Specify the number of times the printer tries to send the fax to a specified number.
1–200 Specify the number of minutes between redials.
Enable or disable switchboard blind dialing without a dial tone.
Enable or disable Error Correction Mode for fax jobs.
Fax files that are scanned at the printer.
Allow the printer driver to send fax jobs.
Allow Save as Shortcut
Save fax numbers as shortcuts in the printer.
Specify the dialing sound, either as a tone or a pulse.

Understanding printer menus 127
Specify the maximum speed in baud at which faxes are sent.
2400 4800 9600 14400 33600
Scan a document that contains mixed paper sizes into a single file.
Adjust the amount of background visible on a scanned image.
‑4 to 4
Specify the contrast in the scanned image.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible.
‑4 to 4
Correct the slight skew in the scanned image.
1–5 Adjust the sharpness of a fax.
Allow the printer to receive fax jobs.
Remove fax jobs from the print queue when the job requires specific unavailable resources.
None Toner Toner and Supplies
1–25 Specify the number of rings before answering an incoming fax job.

Understanding printer menus 128
Scale an incoming fax job so that it fits the size of the paper loaded in the designated fax source.
Specify the paper source for printing incoming fax jobs.
Auto Tray [x] Multi‑Purpose Feeder
Print the transmission information at the bottom of each page from a received fax.
Specify the maximum speed in baud at which faxes are received.
2400 4800 9600 14400 33600
Enable forwarding of received faxes to another recipient.
Print Print and Forward Forward
Specify the type of recipient to which faxes will be forwarded.
Fax E‑mail FTP LDSS eSF
Forward to Shortcut Enter the shortcut number which matches the recipient type (Fax, E-mail, FTP, LDSS, or eSF).
Block No Name Fax
Enable blocking of incoming faxes sent from devices with no fax ID specified.
Enable printing of a transmission log after each fax job.
Print log Do not print log Print only for error
Enable printing of a receive error log following a receive error.
Print Never Print on Error

Understanding printer menus 129
Enable automatic printing of fax logs.
Specify the source of the paper used for printing logs.
Tray [x] Manual Feeder
Specify whether printed logs display the dialed number or fax name returned.
Remote Station Name Dialed Number
Enable access to the Fax Job log.
Enable access to the Fax Call log.
Specify the mode of the speaker.
Always Off On until Connected Always On
Control the volume setting.
Control the fax speaker ringer volume.

Understanding printer menus 130
All Rings Single Ring Only Double Ring Only Triple Ring Only Single or Double Rings Only Single or Triple Rings Only Double or Triple Rings Only
Specify ring patterns when the printer is answering calls.
E‑mail Server Setup
Send a copy of the e-mail to the sender.
Send me a copy
Never appears On by default Off by default Always On
E‑mail Server Setup
Specify the maximum e-mail size in kilobytes.
Max E‑mail size
Specify the format of the scanned file.
PDF (.pdf) Secure PDF TIFF (.tif) JPEG (.jpg) XPS (.xps)
Set the version of the PDF file that will be scanned for e‑mailing.
1.2–1.6 A–1a
Specify the content of the original document.
Graphics Text Text/Photo Photo
Specify how the original document was produced.
Black/White Laser Inkjet Photo/Film Magazine Newspaper Press Other

Understanding printer menus 131
Specify the resolution of the scan in dots per inch.
75 dpi 150 dpi 200 dpi 300 dpi 400 dpi 600 dpi
1–9 Lighten or darken the output.
Specify the orientation of the scanned image.
Specify the paper size of the document being scanned.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in.
Specify the page orientation of text and graphics.
Off Long edge Short edge

Understanding printer menus 132
Set the quality of a JPEG photo image in relation to file size and quality of the image.
Best for content 5–90
5–90 Set the quality of a text image in relation to file size and quality of the image.
5–90 Set the quality of a text or photo image in relation to file size and the quality of the image.
5–90 Set the quality of a photo image in relation to file size and the quality of the image.
E‑mail images sent as
Specify how the images are sent.
Use Multi‑Page Tiff
Provide a choice between single-page TIFF files and multiple‑page TIFF files. For a multiple-page scan‑to‑e-mail job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the job.
Specify whether or not the transmission log prints.
Print log Do not print log Print only for error
Specify the paper source for printing e-mail logs.
Tray [x] Manual Feeder
Copy a document that contains mixed paper sizes.
Allow Save as Shortcut
Save e-mail addresses as shortcuts.
Adjust the amount of background visible on a scanned image.
‑4 to 4

Understanding printer menus 133
Specify the contrast of the output.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4
Correct slight skew in the scanned image.
Scan edge to edge
Specify whether the original document is scanned edge-to-edge.
1–5 Adjust the amount of sharpness on a scanned image.
Use cc:/bcc:
Enable the use of the cc: and bcc: fields.
Specify the format of the file for FTP sending.
PDF (.pdf) Secure PDF (.pdf) TIFF (.tif) JPEG (.jpg) XPS (.xps)
Set the version level of the PDF file for FTP sending.
1.2–1.6 A–1a
Specify the content of the original document.
Text Graphics Text/Photo Photo

Understanding printer menus 134
Specify how the original document was produced.
Black/White Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify the quality of the scan in dots per inch (dpi).
75 dpi 150 dpi 200 dpi 300 dpi 400 dpi 600 dpi
1–9 Lighten or darken the output.
Specify the orientation of the scanned image.
Specify the paper size of the original document.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in.

Understanding printer menus 135
Specify the page orientation of text and graphics.
Off Long Edge Short Edge
Set the quality of a JPEG photo image in relation to the file size and quality of the image.
Best for content 5–90
5–90 Set the quality of the text in relation to the file size and quality of the image.
5–90 Set the quality of a text or photo image in relation to the file size and quality of the image.
5–90 Set the quality of a photo image in relation to the file size and quality of the image.
Use Multi‑Page TIFF
Choose between single-page TIFF files and multiple‑page TIFF files.
For a multiple-page scan‑to‑FTP job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the job.
Specify whether or not the transmission log prints.
Print log Do not print log Print only for error
Specify a paper source when printing FTP logs.
Tray [x] Manual Feeder
Copy a document that contains mixed paper sizes into a single scan job.
Allow Save as Shortcut
Enable shortcut creation for FTP addresses.

Understanding printer menus 136
Adjust the amount of background visible on a copy.
‑4 to 4
Specify the contrast of the output.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4
Correct slight skew in the scanned image.
Scan edge to edge
Specify whether the original document is scanned edge-to-edge.
1–5 Adjust the amount of sharpness of a scanned image
Set the default printer language.
PCL Emulation PS Emulation
Set the logical and physical printable area.

Understanding printer menus 137
Specify how the printer handles temporary downloads, such as fonts and macros stored in the RAM, when the printer receives a job that requires more memory than is available.
Specify whether two‑sided (duplex) printing is set as the user default setting for all print jobs.
1 sided 2 sided
Click File > Print, and then click Properties, Preferences, Options, or Setup. For Macintosh users:
Choose File > Print, and then adjust the settings from the print dialog and pop‑up menus.
Define the way two‑sided pages are bound and printed.
Long Edge Short Edge
1–999 Specify the default number of copies for each print job.
Specify whether or not blank pages are inserted in a print job.
Do Not Print Print
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)

Understanding printer menus 138
Specify whether or not blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages
Specify the paper source for separator sheets.
Tray [x] Manual Feeder
Print multiple pages on one sheet of paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Specify the order in which pages are printed on a single sheet when using Paper Saver.
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify the orientation in which pages are printed on a single sheet.
Print a border when using Paper Saver.

Understanding printer menus 139
Specify the printed output resolution in dots per inch.
300 dpi 600 dpi 1200 dpi 1200 Image Q 2400 Image Q
Enable more pixels to print in clusters for clarity, in order to enhance images horizontally or vertically, or to enhance fonts.
Off Fonts Horizontally Vertically Both directions Isolated
1–10 Lighten or darken the printed output.
Enable a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts.
Automatically adjust the contrast enhancement applied to images.
Adjust the printed output either by lightening or darkening it. You can conserve toner by lightening the output.
‑6 to 6
0–5 Adjust the contrast of printed objects.

Understanding printer menus 140
Print a page containing information on errors, including XML markup errors.
Scale page content to fit the selected paper size.
Print annotations in a PDF.
Do Not Print Print
Specify the set of fonts used in the Font Name menu.
Identify a specific font and where it is stored.
Specify the symbol set for each font name.
Change the point size for scalable typographic fonts.
1.00–1008.00

Understanding printer menus 141
Specify the font pitch for scalable monospaced fonts.
0.08–100.00
Specify the orientation of text and graphics on a page.
Specify the number of lines that print on each page.
Set the printer to print on A4‑size paper.
198 mm 203 mm
Specify whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command.
Auto CR after LF
Specify whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command.
Auto LF after CR

Understanding printer menus 142
Configure the printer to work with printer software or programs that use different source assignments for trays and feeders.
Off None 0–199 Assign Tray [x]
Off None 0–199 Assign Manual Paper
Off None 0–199 Assign Manual Envelope
Show the factory default setting assigned to each tray or feeder.
MPF Default = 8 T1 Default = 1 T2 Default = 4 T3 Default = 5 T4 Default = 20 T5 Default = 21 Env Default = 6 MPaper Default = 2 MEnv Default = 3
Restore all tray and feeder assignments to the factory default settings.

Understanding printer menus 143
Joanna MT Letter Gothic Lubalin Graph Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino StempelGaramond Taffy Times TimesNewRoman Univers Zapf Chancery NewSansMTCS NewSansMTCT New SansMTJA NewSansMTKO
Set the default font for HTML documents.
Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text Intl CG Times Intl Courier Intl Univers
1–255 pt Set the default font size for HTML documents.
1–400% Scale the default font for HTML documents.
Set the page orientation for HTML documents.

Understanding printer menus 144
8–255 mm Set the page margin for HTML documents.
Specify whether to print backgrounds on HTML documents.
Do Not Print Print
Select the optimal paper size, scaling, and orientation.
Invert bitonal monochrome images.
Scale the image to fit the selected paper size.
Anchor Top Left Best Fit Anchor Center Fit Height/Width Fit Height Fit Width
Set the image orientation.
Portrait Landscape Reverse Portrait Reverse Landscape
The Help menu consists of a series of Help pages that are stored in the multifunction printer (MFP) as PDF files. They contain information about using the printer and performing various tasks, including copying, scanning, and faxing.
English, French, German, and Spanish translations are stored in the printer. Other translations are available at http://support.lexmark.com.
Print All Guides Prints all the guides
Copy Guide Provides information about making copies and changing settings

Understanding printer menus 145
E‑mail Guide Provides information about sending e‑mails using addresses, shortcut numbers, or the address book, and about changing settings
Fax Guide Provides information about sending faxes using fax numbers, shortcut numbers, or the address book, and about changing settings
FTP Guide Provides information about scanning documents directly to an FTP server using an FTP address, shortcut numbers, or the address book, and about changing settings
Print Defects Guide Provides help in resolving repeating defects in copies or prints
Information Guide Provides help in locating additional information
Supplies Guide Provides part numbers for ordering supplies
Menu item Description

Saving money and the environment 146
Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impact on the environment. We design with the environment in mind, engineer our packaging to reduce materials, and provide collection and recycling programs. For more information, see:
By selecting certain printer settings or tasks, you may be able to reduce your printer's impact even further. This chapter outlines the settings and tasks that may yield a greater environmental benefit.
Studies show that as much as 80% of the carbon footprint of a printer is related to paper usage. You can significantly reduce your carbon footprint by using recycled paper and the following printing suggestions, such as printing on both sides of the paper and printing multiple pages on one side of a single sheet of paper.
For information on how you can quickly save paper and energy using one printer setting, see "Using Eco-Mode."
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser printers. For more information on recycled papers that work well with your printer, see “Using recycled paper and other office papers” on page 44.
If your printer model supports duplex printing, then you can control whether print appears on one or two sides of the paper by selecting 2‑sided printing from the Print dialog or from the Lexmark Toolbar.
You can print up to 16 consecutive pages of a multiple‑page document onto one side of a single sheet of paper by selecting a setting from the Multipage printing (N‑Up) section of the Print dialog screen.
Before printing or making multiple copies of a document:
Correctly set the paper type and size to avoid paper jams. For more information, see “Avoiding jams” on page 168.

Saving money and the environment 147
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Eco‑Mode.
3 Select a setting.
Off Use the factory default settings for all settings associated with Eco‑Mode.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy and Paper modes.
Plain Paper Enable the automatic two‑sided (duplex) printing feature.
4 Click Submit.
Enable Quiet mode to reduce the printer noise.
1 From the printer control panel, navigate to:
> Settings > > Settings > > General Settings > > Quiet Mode >
2 Select a setting.
Use To

Saving money and the environment 148
On Reduce printer noise.
Off Use factory default settings.
3 Press .
To save energy, decrease the number of minutes before the printer enters Sleep mode. Select from 1 to 120. The factory default setting is 30 minutes.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Navigate to:
Settings > General Settings > Timeouts
3 In the Sleep Mode field, enter the number of minutes you want the printer to wait before it enters Sleep mode.
4 Click Submit.
1 From the printer control panel, navigate to:
> Settings > > Settings > > General Settings > > Timeouts > > Sleep Mode >
2 In the Sleep Mode field, select the number of minutes you want the printer to wait before it enters Sleep mode.
3 Press .
Use To

Saving money and the environment 149
Hibernate is an ultra‑low‑power operating mode. When operating in Hibernate mode, all other systems and devices are powered down safely.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Sleep Button Settings.
3 From the “Press Sleep Button” or “Press and Hold Sleep Button” drop‑down menu, select Hibernate.
4 Click Submit.
1 From the printer control panel, navigate to:
> Settings > > Settings > > General Settings >
2 Press the arrow buttons until Press Sleep Button or Press and Hold Sleep Button appears, and
then press .
3 Press the arrow buttons until Hibernate appears, and then press .
To save energy, or if you have trouble reading the display, adjust its brightness settings.
1 Open a Web browser, and then type the printer IP address in the address field.

Saving money and the environment 150
2 Click Settings > General Settings.
3 In the Screen Brightness field, enter the brightness percentage you want for the display.
4 Click Submit.
Schedule Power Modes lets the user schedule when the printer goes into a reduced power state or into the Ready state.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Schedule Power Modes.
3 From the Action menu, select the power mode.
4 From the Time menu, select the time.
5 From the Day(s) menu, select the day or days.
6 Click Add.
Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information, see:
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country or region from the list.
3 Follow the instructions on the computer screen.

Saving money and the environment 151
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark will recycle the box.
Lexmark Cartridge Collection Program diverts millions of Lexmark cartridges from landfills annually by making it both easy and free for Lexmark customers to return used cartridges to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. Boxes used to return the cartridges are also recycled.
To return Lexmark cartridges for reuse or recycling, follow the instructions that came with your printer or cartridge and use the prepaid shipping label. You can also do the following:
1 Go to www.lexmark.com/recycle.
2 From the Toner Cartridges section, select your country or region.
3 Follow the instructions on the computer screen.

Securing the printer 152
Statement of Volatility
Your printer contains various types of memory that can store device and network settings, and user data.
Type of memory Description
Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print jobs.
Non-volatile memory Your printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store operating system, device settings, and network information.
Erase the content of any installed printer memory in the following circumstances:
The volatile memory (RAM) installed in your printer requires a power source to retain information. To erase the buffered data, simply turn off the printer.
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully powered up, the printer displays a list of functions.
3 Press the up or down arrow button until Wipe All Settings appears.
The printer will restart several times during this process.
4 Navigate to:
Back > Exit Config Menu

Securing the printer 153
The printer will perform a power‑on reset, and then return to normal operating mode.
In high-security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer cannot be accessed by unauthorized persons. For more information, visit the Lexmark security Web page.
You can also see the Embedded Web Server Administrator’s Guide for additional information:
1 Go to http://support.lexmark.com, and then click SELECT YOUR PRODUCT.
2 From the “Search by Product Category” section, navigate to Software and Solutions > Other Applications.
3 Click the Manuals tab, and then select the Embedded Web Server Administrator’s Guide.

Maintaining the printer 154
Cleaning the printer parts
1 Make sure that the printer is turned off and unplugged from the electrical outlet.
2 Remove paper from the standard bin and multipurpose feeder.
3 Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.
4 Dampen a clean, lint-free cloth with water, and use it to wipe the outside of the printer.
5 Make sure all areas of the printer are dry before sending a new print job.

Maintaining the printer 155
Clean the scanner glass if you encounter print quality problems, such as streaks on copied or scanned images.
1 Slightly dampen a soft, lint-free cloth or paper towel with water.
2 Open the scanner cover.
3 Clean all the areas shown, and then let them dry.

1 White underside of the scanner cover
4 White underside of the ADF cover
4 Close the scanner cover.
2 Scanner glass · 3 ADF glass

Maintaining the printer 156
A message appears on the display when a replacement supply item is needed or when maintenance is required.
From the printer control panel, navigate to:
> Status/Supplies > > View Supplies >
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Device Status > More Details.
The estimated number of remaining pages is based on the recent printing history of the printer. Its accuracy may vary significantly and is dependent on many factors, such as actual document content, print quality settings, and other printer settings.
The accuracy of the estimated number of remaining pages may decrease when the actual printing consumption is different from the historical printing consumption. Consider the variable level of accuracy before purchasing or replacing supplies based on the estimate. Until an adequate print history is obtained on the printer, initial estimates assume future supplies consumption based on the International Organization for Standardization* test methods and page content.
* Average continuous black declared cartridge yield in accordance with ISO/IEC 19752.

Maintaining the printer 157
To order parts and supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, visit the Lexmark Web site at www.lexmark.com or contact the place where you purchased the printer.
The Lexmark Return Program lets you purchase Lexmark supplies at a discounted price in exchange for your agreement to use the supplies only once and return them only to Lexmark for remanufacturing or recycling.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. Use of third-party supplies or parts can affect warranty coverage. Damage caused by the use of third-party supplies or parts is not covered by the warranty. All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.
Item Return Program cartridge
United States and Canada
High Yield Toner Cartridge 601H
European Union (EU), European Economic Area (EEA), and Switzerland
High Yield Toner Cartridge 602H
Asia Pacific region (includes Australia and New Zealand)
High Yield Toner Cartridge 603H
Latin America (includes Puerto Rico and Mexico)
High Yield Toner Cartridge 604H
Africa, Middle East, Central Eastern Europe (non‑EU), and Commonwealth of Independent States (CIS)
High Yield Toner Cartridge 605H
For more information on countries located in each region, visit www.lexmark.com/regions.

Maintaining the printer 158
High Yield Toner Cartridge 600HA
Maintenance kit Part number
100‑V maintenance kit* 40X9146
110‑V maintenance kit 40X9135
220‑V maintenance kit 40X9136
* This is available only in Japan.
Order an ADF separator pad when the ADF fails to pick paper or picks more than one sheet of paper at a time.
For information on replacing the ADF separator pad, see the instruction sheet that came with the part.
Part name Part number
Extremely low print coverage for extended periods of time may cause imaging unit parts to fail prior to exhaustion of toner from toner cartridge.
For more information on replacing the imaging unit, see the instruction sheet that came with the supply.
Part name Lexmark Return Program Regular
Imaging unit 500Z 500ZA
Item Regular cartridge · Worldwide · Separator pad 40X6247

Maintaining the printer 159
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:
1 Press the button on the right side of the printer, and then open the front door.


Maintaining the printer 160
2 Pull the toner cartridge out using the handle.

3 Unpack the toner cartridge, and then remove all packing materials.
4 Shake the new cartridge to redistribute the toner.

5 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.


6 Close the front door.

Maintaining the printer 161
1 Press the button on the right side of the printer, and then open the front door.
2 Pull the toner cartridge out using the handle.
3 Lift the green handle, and then pull the imaging unit out of the printer.


Maintaining the printer 162
4 Unpack the new imaging unit, and then shake it.

5 Remove all packing materials from the imaging unit.

6 Insert the imaging unit into the printer by aligning the arrows on the side rails of the imaging unit with the arrows on the side rails inside the printer.


Maintaining the printer 163
7 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.

8 Close the front door.



Maintaining the printer 164
Use only the power cord provided with this product or the manufacturer's authorized replacement.
The printer and its hardware options can be safely moved to another location by following these precautions:
When shipping the printer, use the original packaging or call the place of purchase for a relocation kit.

Managing the printer 165
Finding advanced networking and administrator information
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server Administrator's Guide on the Lexmark Web site at http://support.lexmark.com.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Check the virtual display that appears at the top left corner of the screen.
The virtual display works as an actual display would work on a printer control panel.
Configure the printer to send you e‑mail alerts when the supplies are getting low, when the paper needs to be changed or added, or when there is a paper jam.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings.
3 From the Other Settings menu, click E‑mail Alert Setup.
4 Select the items you want to be notified on, and then type the e‑mail addresses.
5 Click Submit.
You can view some reports from the Embedded Web Server. These reports are useful for assessing the status of the printer, network, and supplies.
1 Open a Web browser, and then type the printer IP address in the address field.

Managing the printer 166
2 Click Reports, and then click the type of report you want to view.
You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Supply Notifications.
3 From the drop‑down menu for each supply, select one of the following notification options:
Off The normal printer behavior for all supplies occurs.
E‑mail Only The printer generates an e‑mail when the supply condition is reached. The status of the supply appears on the menus page and status page.
Continuable Stop1 The printer stops processing jobs when the supply condition is reached, and the user needs to press a button to continue printing.
Non Continuable Stop1,2 The printer stops processing jobs when the supply condition is reached. The supply must be replaced to continue printing.
1 The printer generates an e-mail about the status of the supply when supply notification is enabled.
2 The printer stops when some supplies become empty to prevent damage.
4 Click Submit.
Notification Description

Managing the printer 167
If you want to keep a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings. For more information, see “Printing a menu settings page” on page 29.
If you want a more comprehensive method of restoring the printer factory default settings, then perform the Wipe All Settings option. For more information, see “Erasing non‑volatile memory” on page 152.
From the printer control panel, navigate to:
> Settings > Settings > > General Settings > > Factory Defaults > > Restore Now >

Jam error messages appear on the printer display and include the area of the printer where the jam occurred. When there is more than one jam, the number of jammed pages is displayed.
Correct loading of paper Incorrect loading of paper


Clearing jams 168


When a jam occurs, a message indicating the jam location and information to clear the jam appears on the printer display. Open the doors, covers, and trays indicated on the display to remove the jam.
Clearing jams 169



Jam access area Printer control panel message What to do
1 Automatic document feeder (ADF)
[x]‑page jam, open automatic feeder top cover. [28y.xx]
Remove all paper from the ADF tray, and then remove the jammed paper.
2 Standard bin [x]‑page jam, clear standard bin. [20y.xx]
Remove the jammed paper.
3 Front door [x]‑page jam, open front door. [20y.xx]
Open the front door, then remove the toner cartridge and imaging unit, and then the jammed paper.
4 Multipurpose feeder [x]‑page jam, clear manual feeder. [250.xx]
Remove all paper from the multipurpose feeder, and then remove the jammed paper.
5 Tray 1 [x]‑page jam, remove tray 1 to clear duplex. [23y.xx]
Pull out tray 1 completely, then push the front duplex flap down, and then remove the jammed paper.
6 Tray [x] [x]‑page jam, remove tray [x]. [24y.xx]
Pull out the indicated tray, and then remove the jammed paper.
7 Rear door [x]‑page jam, open rear door. [20y.xx]
Open the rear door, and then remove the jammed paper.
Clearing jams 170
![Page 171 of the Lexmark MX310 user manual — [x] ‑ page jam, open front door. [20y.xx]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-171.webp?w=400)
1 Press the button on the right side of the printer, and then open the front door.
2 Pull the toner cartridge out using the handle.
Clearing jams 171
![Page 172 of the Lexmark MX310 user manual — [x]-page jam, open front door. [20y.xx]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-172.webp?w=400)
3 Lift the green handle, and then pull the imaging unit out of the printer.
4 Place the imaging unit aside on a flat, smooth surface.
5 Lift the green flap in front of the printer.
![Lexmark MX310 — [x]-page jam, open front door. [20y.xx] diagram (page 172)](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/rimg-64.webp)
Clearing jams 172
![Page 173 of the Lexmark MX310 user manual — [x]-page jam, open front door. [20y.xx]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-173.webp?w=400)
6 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark MX310 — [x]-page jam, open front door. [20y.xx] diagram (page 173)](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/rimg-65.webp)
7 Insert the imaging unit by aligning the arrows on the side rails of the unit with the arrows on the side rails inside the printer, and then insert the imaging unit into the printer.
8 Insert the toner cartridge by aligning the side rails of the cartridge with the arrows on the side rails inside the printer, and then insert the cartridge into the printer.
Clearing jams 173
![Page 174 of the Lexmark MX310 user manual — [x] ‑ page jam, open rear door. [20y.xx]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-174.webp?w=400)
9 Close the front door.
10 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > > Clear the jam, press OK > .
1 Open the front door to loosen the jammed paper in the rear door.
2 Gently pull down the rear door.
![Lexmark MX310 — [x] ‑ page jam, open rear door. [20y.xx] diagram (page 174)](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/rimg-66.webp)
3 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 174
![Page 175 of the Lexmark MX310 user manual — [x] ‑ page jam, clear standard bin. [20y.xx]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-175.webp?w=400)
4 Close the rear door, and then the front door.
5 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > > Clear the jam, press OK > .
1 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark MX310 — [x] ‑ page jam, clear standard bin. [20y.xx] diagram (page 175)](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/rimg-67.webp)
2 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > > Clear the jam, press OK > .
Clearing jams 175
![Page 176 of the Lexmark MX310 user manual — [x] ‑ page jam, remove tray 1 to clear duplex. [23y.xx]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-176.webp?w=400)
1 Pull the tray completely out of the printer.
![Lexmark MX310 — [x] ‑ page jam, remove tray 1 to clear duplex. [23y.xx] diagram (page 176)](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/rimg-68.webp)
2 Locate the blue lever, and then pull it down to release the jam.
![Lexmark MX310 — [x] ‑ page jam, remove tray 1 to clear duplex. [23y.xx] diagram (page 176)](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/rimg-69.webp)
![Lexmark MX310 — [x] ‑ page jam, remove tray 1 to clear duplex. [23y.xx] diagram (page 176)](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/rimg-70.webp)
3 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 176
![Page 177 of the Lexmark MX310 user manual — [x] ‑ page jam, open tray [x]. [24y.xx]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-177.webp?w=400)
![Lexmark MX310 — [x]-page jam, open tray [x]. [24y.xx] diagram (page 177)](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/rimg-71.webp)
4 Insert the tray.
to clear the message and continue printing. For non‑touch‑screen printer
5 From the printer control panel, touch
models, select Next > > Clear the jam, press OK > .
1 Pull the tray completely out of the printer.
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 177
![Page 178 of the Lexmark MX310 user manual — [x] ‑ page jam, clear manual feeder. [25y.xx]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-178.webp?w=400)
![Lexmark MX310 — [x]-page jam, clear manual feeder. [25y.xx] diagram (page 178)](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/rimg-72.webp)
3 Insert the tray.
to clear the message and continue printing. For non‑touch‑screen printer
4 From the printer control panel, touch
models, select Next > > Clear the jam, press OK > .
1 From the multipurpose feeder, firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark MX310 — [x] ‑ page jam, clear manual feeder. [25y.xx] diagram (page 178)](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/rimg-73.webp)
2 Flex the sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.
![Lexmark MX310 — [x] ‑ page jam, clear manual feeder. [25y.xx] diagram (page 178)](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/fig-178-1.webp)
Clearing jams 178
![Page 179 of the Lexmark MX310 user manual — [x] ‑ page jam, open automatic feeder top cover. [28y.xx]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-179.webp?w=400)
3 Reload paper into the multipurpose feeder.
to clear the message and continue printing. For non‑touch‑screen printer
4 From the printer control panel, touch
models, select Next > > Clear the jam, press OK > .
1 Remove all original documents from the ADF tray.
2 Open the ADF cover.
![Lexmark MX310 — [x] ‑ page jam, open automatic feeder top cover. [28y.xx] diagram (page 179)](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/rimg-74.webp)
3 Firmly grasp the jammed paper on each side, and then gently pull it out.
4 Close the ADF cover.
Clearing jams 179
![Page 180 of the Lexmark MX310 user manual — [x]-page jam, open automatic feeder top cover. [28y.xx]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-180.webp?w=400)
5 Straighten the edges of the original documents, then load the original documents into the ADF, and then adjust the paper guide.
6 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > > Clear the jam, press OK > .
Clearing jams 180
![Page 181 of the Lexmark MX310 user manual — Change [paper source] to [custom string] load [paper orientation]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-181.webp?w=400)
Understanding printer messages
1 Check if the toner cartridge and imaging unit are both MICR (Magnetic Imaging Content Recording) or non-MICR supplies.
2 Change the toner cartridge or imaging unit so that both are MICR or non‑MICR supplies.
You may need to order a toner cartridge. If necessary, select Continue on the printer control panel to clear the message
and continue printing. For non‑touch‑screen printer models, press to confirm.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to replace the toner cartridge very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
models, press to confirm. • Cancel the print job.
Troubleshooting 181

Try one or more of the following
press to confirm. • Cancel the print job.
Try one or more of the following:
press to confirm. • Cancel the print job.
Try one or more of the following:
press to confirm. • Cancel the print job.
From the printer control panel, try one or more of the following:
Close the front door of the printer.
Troubleshooting 182

Try one or more of the following:
printer models, press to confirm.
Try one or more of the following:
printer models, press to confirm. • Cancel the current print job.
Error reading USB drive. Remove USB.
An unsupported USB device is inserted. Remove the USB device, and then insert a supported one.
Error reading USB hub. Remove hub.
An unsupported USB hub has been inserted. Remove the USB hub, and then install a supported one.
From the printer control panel, touch Continue to clear the message.
Fax partition inoperative. Contact system administrator.
Try either of the following:
to confirm. • Turn the printer off, and then turn it back on. If the message appears again, then contact your system support person or see the “Setting up the printer to fax” section of the User’s Guide.
Fax server 'To Format' not set up. Contact system administrator.
Try either of the following:
to confirm. • Complete the Fax Server setup. If the message appears again, then contact your system support person.
Troubleshooting 183
![Page 184 of the Lexmark MX310 user manual — Incorrect paper size, open [paper source] [34]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-184.webp?w=400)
Fax Station Name not set up. Contact system administrator.
Try either of the following:
to confirm. • Complete the Analog Fax Setup. If the message appears again after completing the setup, then contact your system support person.
Fax Station Number not set up. Contact system administrator.
Try either of the following:
to confirm. • Complete the Analog Fax Setup. If the message appears again after completing the setup, then contact your system support person.
You may need to order an imaging unit. If necessary, select Continue on the printer control panel to clear the message
and continue printing. For non‑touch‑screen printer models, press to confirm.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to replace the imaging unit very soon. For more information, see the "Replacing supplies" section of the User’s Guide.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
Troubleshooting 184
![Page 185 of the Lexmark MX310 user manual — Insufficient memory to support Resource Save feature [35]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-185.webp?w=400)
Try one or more of the following:
The printer deleted some held jobs in order to process current jobs.
Select Continue to clear the message. For non-touch-screen printer models, press to confirm.
Try one or more of the following:
to confirm. • Delete other held jobs to free up additional printer memory.
Try one or more of the following:
rest of the print job. For non‑touch‑screen printer models, press to confirm. • Cancel the current print job.
Install additional printer memory or select Continue on the printer control panel to disable Resource Save, clear the
message, and continue printing. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 185
![Page 186 of the Lexmark MX310 user manual — Load manual feeder with [paper type] [paper size] [paper orientation]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-186.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 186
![Page 187 of the Lexmark MX310 user manual — Load [paper source] with [paper type] [paper size] [paper orientation]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-187.webp?w=400)
Try one or more of the following:
For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
panel. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
control panel. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 187
![Page 188 of the Lexmark MX310 user manual — Memory full [38]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-188.webp?w=400)
You may need to order a maintenance kit. For more information, contact customer support at http://support.lexmark.com or your service representative. If necessary, select Continue to clear the message and
continue printing. For non‑touch‑screen printer models, press to confirm.
For more information, contact customer support at http://support.lexmark.com or your service representative. If necessary, select Continue to clear the message and continue printing. For non‑touch‑screen printer models,
press to confirm.
You may need to replace the maintenance kit very soon. For more information, contact customer support at http://support.lexmark.com or your service representative.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
From the printer control panel, select Continue to clear the message without printing. For non‑touch‑screen printer
models, press to confirm.
1 From the printer control panel, select Continue to clear the message and cancel the fax job. For non‑touch‑screen
printer models, press to confirm.
Try one or more of the following:
to confirm. • Install additional printer memory.
Troubleshooting 188
![Page 189 of the Lexmark MX310 user manual — Not enough free space in flash memory for resources [52]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-189.webp?w=400)
Try one or more of the following:
No analog phone line connected to modem, fax is disabled.
Connect the printer to an analog phone line.
The printer has detected a non‑Lexmark supply or part installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components.
All life indicators are designed to function with Lexmark supplies and parts and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or associated components.
To accept any and all of these risks and to proceed with the use of non-genuine supplies or parts in your printer, press
and the # button on the printer control panel simultaneously for 15 seconds.
For non‑touch‑screen printer models, press and
on the printer control panel simultaneously for 15 seconds to clear the message and continue printing.
If you do not wish to accept these risks, then remove the third-party supply or part from your printer, and then install a genuine Lexmark supply or part.
Try one or more of the following:
Troubleshooting 189 · and hold

Printer had to restart. Last job may be incomplete.
to clear the message and continue printing. For non‑touch‑screen printer
From the printer control panel, touch
models, press to confirm.
For more information, visit http://support.lexmark.com or contact customer support.
Try one or more of the following:
For information on installing the cartridge, see the “Replacing supplies” section of the User’s Guide. • If the toner cartridge is installed, then remove the unresponsive toner cartridge, and then reinstall it.
Try one or more of the following:
For information on installing the imaging unit, see the “Replacing supplies” section of the User’s Guide. • If the imaging unit is installed, then remove the unresponsive imaging unit, and then reinstall it.
Remove the paper stack from the standard bin. The printer automatically detects paper removal and resumes printing.
If removing the paper does not clear the message, then select Continue on the printer control panel. For non-touch-
screen printer models, press to confirm.
Replace all originals if restarting job.
From the printer control panel, try one or more of the following:
Troubleshooting 190
![Page 191 of the Lexmark MX310 user manual — Replace imaging unit, 0 estimated pages remain [84.xy]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-191.webp?w=400)
Replace the toner cartridge to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Install a toner cartridge that matches the region number of the printer. x indicates the value of the printer region. y indicates the value of the cartridge region. x and y can have the following values:
1 United States, Canada
2 European Economic Area (EEA), Switzerland
3 Asia Pacific, Australia, New Zealand
5 Africa, Middle East, rest of Europe
Replace the defective imaging unit to clear the message. For more information, see the instruction sheet that came with the supply.
Replace the imaging unit to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
![Page 192 of the Lexmark MX310 user manual — Scanner disabled by admin [840.01]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-192.webp?w=400)
Replace jammed originals if restarting job.
From the printer control panel, try one or more of the following:
job. For non‑touch‑screen printer models, press to confirm. • Select Scan from flatbed to continue scanning from the scanner immediately after the last successful scan job. For
non‑touch‑screen printer models, press to confirm. • Select Finish job without further scanning to end the last successful scan job. For non‑touch‑screen printer models,
press to confirm. • Select Restart job to restart the scan job with the same settings from the previous scan job. For non‑touch‑screen
printer models, press to confirm.
Contact customer support at http://support.lexmark.com or your service representative, and then report the message. The printer is scheduled for maintenance.
Remove the toner cartridge, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Remove the imaging unit, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Close the ADF cover.
Print without the scanner, or contact your system support person.
Troubleshooting 192
![Page 193 of the Lexmark MX310 user manual — Standard network software error [54]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-193.webp?w=400)
From the printer control panel, try one or more of the following:
Remove the jammed paper from the scanner.
Remove the jammed paper from the scanner.
Try one or more of the following:
to confirm. • Turn off the printer, and then turn it back on.
SMTP server not set up. Contact system administrator.
From the printer control panel, select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
Troubleshooting 193
![Page 194 of the Lexmark MX310 user manual — Unformatted flash detected [53]](/cdn/reader/85/857dfacc2feac02c5662839b0f23c1f0673fd4c5b21044b6bc5c2b91b638905c/images/page-194.webp?w=400)
From the printer control panel, select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Do either of the following:
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra flash memory.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra trays.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Try one or more of the following:
printer models, press to confirm. • Format the flash memory.
Troubleshooting 194

Weblink server not set up. Contact system administrator.
Select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Go to step 2. Turn on the printer.
Make sure the printer is turned on.
Is the printer turned on?
Press the Sleep button to wake the printer from Sleep mode or Hibernate mode.
Go to step 3.
Check if the printer is in Sleep mode or Hibernate mode.
Is the printer in Sleep mode or Hibernate mode?
Go to step 4. Plug one end of the power cord into the printer and the other to a properly grounded electrical outlet.
Check if one end of the power cord is plugged into the printer and the other to a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
Unplug the other electrical equipment, and then turn on the printer. If the printer does not work, then reconnect the other electrical equipment.
Go to step 5.
Check other electrical equipment plugged into the electrical outlet.
Does other electrical equipment work?

Go to step 6. Make sure to match the following:
Check if the cables connecting the printer and the computer are inserted in the correct ports.
Are the cables inserted in the correct ports?
Turn on the switch or reset the breaker.
Go to step 7.
Make sure the electrical outlet is not turned off by a switch or breaker.
Is the electrical outlet turned off by a switch or breaker?
Connect the printer power cord directly to a properly grounded electrical outlet.
Go to step 8.
Check if the printer is plugged into any surge protectors, uninterruptible power supplies, or extension cords.
Is the printer plugged into any surge protectors, uninterruptible power supplies, or extension cords?
Go to step 9. Connect the printer cable securely to the printer and the computer, print server, option, or other network device.
Check if one end of the printer cable is plugged into a port on the printer and the other to the computer, print server, option, or other network device.
Is the printer cable securely attached to the printer and the computer, print server, option, or other network device?
Step 9 Make sure to install all hardware options properly and remove any packing material.
Go to step 10. Turn off the printer, remove all packing materials, then reinstall the hardware options, and then turn on the printer.
Are all hardware options properly installed and all packing material removed?
Go to step 11. Use correct printer driver settings.
Check if you have selected the correct port settings in the printer driver.
Are the port settings correct?
Step 11 Check the installed printer driver.
Go to step 12. Install the correct printer driver.
Is the correct printer driver installed?
The problem is solved. Contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Is the printer working?

Step 1 Press the Sleep button on the printer control panel.
The problem is solved. Go to step 2.
Does Ready appear on the printer display?
The problem is solved. Turn off the printer, and then contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Do Please wait and Ready appear on the printer display?
The problem is solved. Go to step 2.
Turn off the printer, then wait for about 10 seconds, and then turn on the printer.
Does the internal option operate correctly?
Go to step 3. Connect the internal option to the controller board.
Check if the internal option is properly installed in the controller board.
a Turn off the printer using the power switch, and then unplug the power
cord from the electrical outlet. b Make sure the internal option is installed in the appropriate connector
in the controller board. c Connect the power cord to the printer, then to a properly grounded
electrical outlet, and then turn on the printer.
Is the internal option properly installed in the controller board?
Go to step 4. Reinstall the internal option.
Print a menu settings page, and then check to see if the internal option is listed in the Installed Features list.
Is the internal option listed in the menu settings page?

The problem is solved. Contact customer support.
a Check if the internal option is selected.
It may be necessary to manually add the internal option in the printer driver to make it available for print jobs. For more information, see “Updating available options in the printer driver” on page 23. b Resend the print job.
Does the internal option operate correctly?
The problem is solved. Go to step 2.
a Pull out the tray, and then do one or more of the following:
Is the tray working?
The problem is solved. Go to step 3.
a Turn off the printer, then wait about 10 seconds, and then turn the
printer back on. b Resend the print job.
Is the tray working?
Go to step 4. Reinstall the tray. For more information, see the setup documentation that came with the tray.
Check if the tray is installed and recognized by the printer.
Print a menu settings page, and then check if the tray is listed in the Installed Features list.
Is the tray listed in the menu settings page?
The problem is solved. Contact customer support.
Check if the tray is available in the printer driver.
Is the tray available in the printer driver?

a Turn on jam recovery.
The problem is solved. Contact customer support.
1 From the printer control panel, navigate to:
Settings > General Settings > Print Recovery > Jam Recovery 2 Select On or Auto.
3 Depending on your printer model, press or touch Submit. b Resend the pages that did not print.
Were the jammed pages reprinted?
Go to step 2. The problem is solved.
a Pull out the tray, and then do one or more of the following:
If jam recovery is enabled, then the print jobs will reprint automatically.
Do paper jams still occur frequently?
Go to step 3. The problem is solved.
a Load paper from a fresh package.
Do paper jams still occur frequently?
Contact customer support.
The problem is solved.
a Review the tips on avoiding jams. For more information, see “Avoiding
jams” on page 168. b Follow the recommendations, and then resend the print job.
Do paper jams still occur frequently?

a Do either of the following:
Contact customer support.
The problem is solved.
or Done.
the jam, press OK > . b Follow the instructions on the printer display.
Does the paper jam message remain?
Deactivate Hex Trace mode.
Go to step 2.
Make sure the printer is not in Hex Trace mode.
Is the printer in Hex Trace mode?
Contact customer support.
The problem is solved.
a From the printer control panel, select Standard Network or
Network [x], and then set SmartSwitch to On. b Resend the print job.
Do incorrect characters print?
The problem is solved. Go to step 2.
a Check if you are printing on paper that is supported by the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?

The problem is solved. Go to step 3.
a From the Paper menu on the printer control panel, set the paper size
and type to match the paper loaded in the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 4.
a Depending on your operating system, open Printing Preferences or
the Print dialog, and then specify the paper type. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Contact customer support.
a Check if the trays are not linked. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 2.
a From the Finishing menu on the printer control panel, set Collate to
“(1,2,3) (1,2,3).” b Resend the print job.
Did the job print and collate correctly?
The problem is solved. Go to step 3.
a From the printer software, set Collate to “(1,2,3) (1,2,3).”
Did the job print and collate correctly?
The problem is solved. Contact customer support.
Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Did the job print and collate correctly?

Multiple‑language PDF files do not print
The problem is solved. Go to step 2.
a Check if the print options for the PDF output are set to embed all fonts.
For more information, see the documentation that came with Adobe Acrobat. b Generate a new PDF file, and then resend the print job.
Do the files print?
The problem is solved. Contact customer support.
a Open the document you want to print in Adobe Acrobat. b Click File > Print > Advanced > Print As Image > OK > OK.
Do the files print?
The problem is solved. Go to step 2.
a From the document you are trying to print, open the Print dialog and
check if you have selected the correct printer.
Do the jobs print?
The problem is solved. Go to step 3.
a Check if the printer is plugged in and turned on, and if Ready appears
on the printer display. b Resend the print job.
Do the jobs print?
The problem is solved. Go to step 4.
If an error message appears on the printer display, then clear the message.
Do the jobs print?

The problem is solved. Go to step 5.
a Check if the ports (USB, serial, or Ethernet) are working and if the
cables are securely connected to the computer and the printer.
Do the jobs print?
The problem is solved. Go to step 6.
a Turn off the printer, then wait for about 10 seconds, and then turn the
printer back on. b Resend the print job.
Do the jobs print?
The problem is solved. Contact customer support.
a Remove, and then reinstall the printer software. For more
information, see “Installing the printer software” on page 23.
Do the jobs print?
The problem is solved. Go to step 2.
Change the environmental settings of the printer.
a From the printer control panel, navigate to:
Settings > General Settings b Select Eco‑Mode or Quiet Mode, and then select Off.
Did the job print?
The problem is solved. Go to step 3.
Reduce the number and size of fonts, the number and complexity of images, and the number of pages in the print job, and then resend the job
Did the job print?

The problem is solved. Go to step 4.
a Remove held jobs stored in the printer memory. b Resend the print job.
Did the job print?
The problem is solved. Go to step 5.
a Disable the Page Protect feature.
From the printer control panel, navigate to:
Settings > General Settings > Print Recovery > Page Protect > Off b Resend the print job.
Did the job print?
The problem is solved. Contact customer support.
a Check if the cable connections to the printer and print server are
secure. For more information, see the setup documentation that came with the printer. b Resend the print job.
Did the job print?
The problem is solved. Go to step 2.
a Make sure the size of the paper loaded in the tray matches the fuser
type.
Does the print speed increase?
The problem is solved. Contact customer support.
a Replace the fuser. For more information on installing the fuser, see
the instruction sheet that came with the part. b Resend the print job.
Does the print speed increase?

The problem is solved. Go to step 2.
a Open the trays, and then check if they contain paper of the same size
and type.
Do the trays link correctly?
The problem is solved. Contact customer support.
a From the printer control panel, set the paper size and type in the Paper
menu to match the paper loaded in the trays to be linked.
Do the trays link correctly?
The problem is solved. Go to step 2.
Adjust the print timeout settings.
a From the printer control panel, navigate to:
Settings > General Settings > Timeouts > Print Timeout b Select a higher setting and then, depending on your printer model,
select or Submit. c Resend the print job.
Did the file print correctly?
The problem is solved. Contact customer support.
a Check the original file for manual page breaks. b Resend the print job.
Did the file print correctly?


Go to step 2. Select a font that is supported by the printer.
a Print a font sample list to check if the fonts you are using are supported
Menus > Reports > Print Fonts 2 Select PCL Fonts or PostScript Fonts. b Resend the print job.
Are you using fonts that are supported by the printer?
Check if the fonts installed on the computer are supported by the printer.
Are the fonts installed on the computer supported by the printer?

a Move the width and length guides in the tray to the correct positions
for the paper loaded. b Resend the print job.
Troubleshooting 206

Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Do the paper size and type match the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.
Is the page or image clipped?
Contact customer support.
The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge. 2 Remove the imaging unit.
Is the page or image clipped?
The problem is solved. Go to step 2.
a Make sure the size of the paper loaded in the tray matches the fuser
type.
Do compressed images still appear?


a Replace the fuser. For more information on installing the fuser, see
the instruction sheet that came with the part. b Resend the print job.

a From the Quality Menu on the printer control panel, decrease the
a Remove the toner cartridge. b Remove the imaging unit.
Replace the imaging unit, and then resend the print job.
Troubleshooting 208


a Make sure your software program is using a correct fill pattern. b Resend the print job.
a Load the specified tray or feeder with a recommended type of paper. b Resend the print job.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Replace the imaging unit, and then resend the print job.
Troubleshooting 209

ABCD ABCD ABCD
The problem is solved. Go to step 2.
a Move the width and length guides in the tray to the correct positions
for the paper size loaded. b Resend the print job.
Are the margins correct?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size in the Paper menu to match the paper loaded in the tray.
Does the paper size match the paper loaded in the tray?
The problem is solved. Contact customer support.
a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.
Are the margins correct?

Step 1 Move the width and length guides in the tray to the correct positions for the size of the paper loaded.
Go to step 2. Adjust the width and length guides.
Are the width and length guides positioned correctly?
Step 2 From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Go to step 3. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the paper still curled?
Go to step 5. The problem is solved.
a Remove the paper from the tray, and then turn it over. b Resend the print job.
Is the paper still curled?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Is the paper still curled?
) ) ABCDE
ABCDE ABCDE

Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded in the tray. b Resend the print job.
Do print irregularities still appear?
Go to step 3. Specify the paper size and type from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Do the printer settings match the type and weight of the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do print irregularities still appear?
From the printer control panel, set the paper texture in the Paper menu to match the paper loaded in the tray.
Go to step 5.
Check if the paper loaded in the tray has texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Do print irregularities still appear?
Contact customer support at http://support.lexmar k.com or your service representative.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do print irregularities still appear?

Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, reduce the toner
darkness.
Is the print still too dark?
Go to step 3. Do one or more of the following:
a From the printer control panel, set the paper type, texture and weight
in the Paper menu to match the paper loaded in the tray. b Resend the print job.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type, texture
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too dark?
From the printer control panel, change the texture settings in the Paper Texture menu to match the paper you are printing on.
Go to step 5.
Check if the paper loaded in the tray has texture or rough finishes.
Are you printing on textured or rough paper?

Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too dark?
Step 6 Replace the imaging unit, and then resend the print job.
Contact customer support.
The problem is solved.
Is the print still too dark?
Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, increase the toner
darkness.
Is the print still too light?
Step 2 From the printer control panel, set the paper type, texture, and weight in the Paper menu to match the paper loaded in the tray.
Go to step 3. Change the paper type, texture, and weight to match the paper loaded in the tray.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too light?

From the printer control panel, change the texture settings in the Paper Texture menu to match the paper you are printing on.
Go to step 5.
Make sure that the paper has no texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too light?
Go to step 7. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Is the print still too light?
Step 7 Replace the imaging unit, and then resend the print job.
Contact customer support.
The problem is solved.
Is the print still too light?

Go to step 2. The problem is solved.
a Check if there is packing material left on the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Check if the packing material is properly removed from the imaging unit.
Is the printer still printing blank pages?
Go to step 3. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Is the printer still printing blank pages?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the printer still printing blank pages?

Go to step 2. The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge, and then the imaging unit.
Is the printer printing solid black pages?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the printer printing solid black pages?
Go to step 2. 1 Check if the distance between the defects equal to 80 mm (3.15 in.) 2 Take note of the distance, and then contact customer support at http://support.le xmark.com or your service representative.
Measure the distance between the defects.
Check for a distance between the defects that equals:
Is the distance between defects equal to one of the listed measurements?
Contact customer support at http://support.lexma rk.com or your service representative.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do the repeating defects still appear?


Go to step 2. Load paper with the correct paper type and weight in the tray.
Load paper with the correct paper type and weight in the tray.
Is paper with the correct paper type and weight loaded in the tray?
Go to step 3. Change the paper loaded in the tray to match the paper type and weight specified in the tray settings.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Is the tray set to the type and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do shadow images still appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do shadow images still appear on prints?
) ) ABCDE
ABCDE ABCDE

Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded. b Resend the print job.
Is the print still skewed?
Contact customer support.
The problem is solved.
a Check if you are printing on a paper that is supported by the tray. b Resend the print job.
Is the print still skewed?
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the tray or feeder from
Printing Preferences or the Print dialog. b Resend the print job.
Do streaked horizontal lines appear on prints?
Go to step 3. Change the paper type and weight to match the paper loaded in the tray.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked horizontal lines appear on prints?


1 Remove the toner cartridge, and then the imaging unit.
Replace the imaging unit, and then resend the print job.
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do streaked vertical lines appear on prints?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper texture, type, and weight in the Paper menu to match the paper loaded in the tray.
Do the paper texture, type, and weight match the paper in the tray?

Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked vertical lines appear on prints?
Go to step 5. The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge, and then the imaging unit.
Do streaked vertical lines appear on prints?
Contact customer support at http://support.lexmar k.com or your service representative.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do streaked vertical lines appear on prints?
ABCDE
ABCDE ABCDE
Go to step 2. The problem is solved.
Reinstall the imaging unit.
a Remove, and then install the imaging unit. b Resend the print job.
Does fog or shading appear on prints?
Step 2 Replace the imaging unit, and then resend the print job.
Contact customer support at http://support.lexmar k.com or your service representative.
The problem is solved.
Does fog or shading appear on prints?


Go to step 2. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
From the Paper menu on the printer control panel, check the paper type and weight.
Do the paper type and texture match the paper loaded in the tray?
From the Paper menu on the printer control panel, set the paper texture.
Check if you are printing on paper with texture or rough finishes.

Replace the imaging unit, and then resend the print job.

Go to step 2. Set the paper type to Transparency.
From the printer control panel, set the paper type in the Paper menu to match the paper loaded in the tray.
Is the paper type for the tray set to Transparency?
a Check if you are using a recommended type of transparency. b Resend the print job.
Troubleshooting 222


Replace the imaging unit, and then resend the print job.

a Make sure your software program is using a correct fill pattern. b Resend the print job.
a From the printer control panel, set the paper type and weight in the
Paper menu to match the paper loaded in the tray. b Resend the print job.
Check if you are using a recommended type of paper.
a Load the specified tray or feeder with a recommended type of paper. b Resend the print job.
Troubleshooting 223

Go to step 5. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Do vertical voids appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do vertical voids appear on prints?
Clear the error or status message.
Go to step 2.
Check if an error or status message appears on the display.
Does an error or status message appear?
Go to step 3. Connect the power cord to the printer and a properly grounded electrical outlet.
Check if the power cord is plugged into the printer and a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
The problem is solved. Contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn it back on.
Did Performing Self Test and Ready appear?

Check if there are no obstructions between the scanner unit and the printer.
The problem is solved. Contact customer support.
a Lift the scanner unit. b Remove any obstruction that keeps the scanner unit open.
c Lower the scanner unit.
Did the scanner unit close properly?
Clear the error or status message.
Go to step 2.
Check if an error or status message appears on the display.
Does an error or status message appear?
Go to step 3. Increase the scan resolution setting for a higher‑quality output.
Check the quality of the original document.
Is the quality of the original document satisfactory?
Go to step 4. See “Cleaning the scanner glass” on page 155.
If dark marks appear on prints, then clean the scanner glass and the ADF glass using a clean, lint-free cloth dampened with water.
Is the scanner glass clean?
Go to step 5. See “Print quality problems” on page 206.
Send a print job, and then check for print quality problems.
a From the General Settings menu, adjust the Eco‑Mode settings. b From the Copy menu, adjust the Darkness setting.
c If the print remains faded, then replace the toner cartridge.
Is the print quality satisfactory?
Go to step 6. Place the document or photo facedown on the scanner glass in the upper left corner.
Check the placement of the document or photo.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Is the document or photo loaded correctly?

Go to step 7. Change the Content Type and Content Source settings to match the document being scanned.
Check the copy settings.
From the Copy screen, check if the Content Type and Content Source settings are correct for the document being scanned.
Are the Content Type and Content Source settings correct for the document being scanned?
Go to step 8. The problem is solved.
Check for patterns on print.
a From the printer control panel, navigate to:
Copy > Sharpness > select a lower setting
Do patterns appear on prints?
Go to step 9. The problem is solved.
Check for missing or faded text on prints.
a From the Copy screen, adjust the settings of the following:
Do prints have missing or faded text?
Contact customer support.
The problem is solved.
Check for washed‑out or overexposed output.
a From the Copy screen, adjust the settings of the following:
Do pages show washed‑out or overexposed prints?
Go to step 2. Place the document or photo facedown on the scanner glass in the upper left corner.
Check the placement of the document or photo.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Is the document or photo loaded correctly?

Go to step 3. Change the paper size setting to match the paper loaded in the tray, or load the tray with paper that matches the paper size setting.
Check if the paper size setting matches the size of the paper loaded in the tray.
From the Paper menu on the printer control panel, check the Paper Size setting.
Does the paper size setting match the size of the paper loaded in the tray.
The problem is solved. Contact customer support.
a Specify the paper size. Depending on your operating system, specify
the paper size in Printing Preferences or the Print dialog. b Resend the print job.
Do copies print properly?
Before completing these instructions for network printers, check if the fax cables are connected.

a From the printer control panel, navigate to:
The problem is solved. Contact customer support.
> Settings > > General Settings > > Run initial setup >
> b Turn off the printer, and then turn it back on.
The “Select your language” screen appears on the printer display.
c Select a language, and then press .
d Select a country or region, and then press .
e Select a time zone, and then press . f Press the up or down arrow button to scroll to Fax, and then press
Is the fax function set up?
Contact your telephone company to check if your telephone line is subscribed to the caller ID service.
The problem is solved. Contact customer support.
Does the caller ID appear?
Troubleshooting 228 · Action Yes No · Action Yes No

Clear the error or status message.
Go to step 2.
Check if an error or status message appears on the display.
Is there an error or status message on the display?
Go to step 3. Connect the power cord to the printer and a properly grounded electrical outlet.
Check if the power cord is plugged into the printer and a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
Go to step 4. Turn on the printer, and then wait until Ready appears on the display.
Check the power.
Check if the printer is plugged in and turned on, and if Ready appears on the display.
Is the printer turned on, and does Ready appear on the display?
Go to step 5. Securely connect the cables.
Check the printer connections.
If applicable, check if the cable connections for the following equipment are secure:
Are the cable connections secure?
The problem is solved. Go to step 6.
a Check the telephone wall jack.
1 Plug the telephone cable into the wall jack. 2 Listen for a dial tone. 3 If you do not hear a dial tone, then plug a different telephone cable into the wall jack. 4 If you still do not hear a dial tone, then plug the telephone cable into a different wall jack. 5 If you hear a dial tone, then connect the printer to that wall jack. b Try sending or receiving a fax.
Can you send or receive a fax?

Go to step 7. Connect the printer to an analog phone service or the correct digital connector.
Check if the printer is connected to an analog phone service or the correct digital connector.
The fax modem is an analog device. Certain devices can be connected to the printer so that digital telephone services can be used.
Is the printer connected to an analog phone service or the correct digital connector?
Check for a dial tone.
Did you hear a dial tone?
The problem is solved. Go to step 9.
Temporarily disconnect other equipment (such as answering machines, computers with modems, or telephone line splitters) between the printer and the telephone line, and then try sending or receiving a fax.
Can you send or receive a fax?
The problem is solved. Go to step 10.
a Temporarily disable call waiting. Contact your telephone company to
obtain the keypad sequence for temporarily disabling call waiting. b Try sending or receiving a fax.
Can you send or receive a fax?

The problem is solved. Go to step 11.
a Temporarily disable voice mail service. For more information, contact
your telephone company.
Can you send or receive a fax?
The problem is solved. Contact customer support.
Scan the original document one page at a time.
a Dial the fax number. b Scan the document one page at a time.
Can you send or receive a fax?
The problem is solved. Go to step 2.
Check the tray or feeder.
If empty, then load paper in the tray or feeder.
Can you receive faxes?
The problem is solved. Go to step 3.
Check the ring count delay settings.
a Open a Web browser, and then type the printer IP address in the
address field.
c In the “Rings to Answer” field, enter the number of times you want
the phone to ring before the printer answers. d Click Submit.
Can you receive faxes?

The problem is solved. Contact customer support.
Replace the toner cartridge. For more information, see the instruction sheet that came with the supply.
Can you receive faxes?
The problem is solved. Go to step 2.
Check if the printer is in Fax mode.
From the printer control panel, press Fax to put the printer in fax mode, and then resend the fax job.
Can you send faxes?
The problem is solved. Go to step 3.
a Load the original document faceup, short edge first into the ADF tray
or facedown on the scanner glass in the upper left corner.
Can you send faxes?
The problem is solved. Contact customer support.
a Check if the shortcut number is configured for the number that you
want to dial.
Can you send faxes?

The problem is solved. Go to step 2.
Ask the person who sent you the fax to:
a Check if the quality of the original document is satisfactory. b Increase the fax scan resolution, if possible.
c Resend the fax. There may have been a problem with the quality of
the telephone line connection.
Is the fax print quality satisfactory?
The problem is solved. Go to step 3.
Decrease the incoming fax transmission speed.
a Open a Web browser, and then type the printer IP address in the
address field.
c In the Max Speed menu, click one of the following:
Is the fax print quality satisfactory?
The problem is solved. Contact customer support.
Replace the toner cartridge.
When Cartridge low [88.xy] appears, replace the cartridge, and then resend the fax.
Is the fax print quality satisfactory?

Go to step 2. Turn on the printer.
Check if the printer is turned on.
Is the printer turned on?
Go to step 3. Connect the printer cable securely to the printer and the computer, print server, option, or other network device.
Check if the printer cable is securely attached to the printer and the computer, print server, option, or other network device.
Is the printer cable securely attached to the printer and the computer, print server, option, or other network device?
Step 3 Check if the power cord is plugged into the printer and a properly grounded electrical outlet.
Go to step 4. Connect the power cord to the printer and a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
Turn on the switch or reset the breaker.
Go to step 5.
Check if the electrical outlet is turned off by a switch or breaker.
Is the electrical outlet turned off by a switch or breaker?
Step 5 Check if the printer is plugged into any surge protectors, uninterruptible power supplies, or extension cords.
Connect the printer power cord directly to a properly grounded electrical outlet.
Go to step 6.
Is the printer plugged into any surge protectors, uninterruptible power supplies, or extension cords?
Unplug the other electrical equipment and turn on the printer. If the printer does not work, then reconnect the other electrical equipment and then go to step 6.
Go to step 7.
Check other electrical equipment plugged into the outlet.
Are the other electrical equipment working?
The problem is solved. Contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Are the printer and scanner working?

Go to step 2. Connect the cables properly.
Check the cable connections.
Make sure the Ethernet or USB cable is securely connected to the computer and the printer.
Are the cables securely connected?
Change the file name. Go to step 3.
Check if the file name is already in use.
Is the file name already in use?
Step 3 Check if the document or photo you want to scan is open in another application or being used by another user.
Close the file you are scanning.
Go to step 4.
Is the file you want to scan open by another application or user?
Step 4 Check if either the Append time stamp or the Overwrite existing file check box is selected in the destination configuration settings.
Contact customer support.
Select the Append time stamp or Overwrite existing file check box in the destination configuration settings.
Is the Append time stamp or Overwrite existing file check box selected in the destination configuration settings?
Check if there are obstructions in the scanner unit.
The problem is solved. Contact customer support.
a Lift the scanner unit. b Remove any obstruction keeping the scanner unit open.
c Lower the scanner unit.
Did the scanner unit close correctly?
Go to step 2. The problem is solved.
Check if other applications are interfering with the scan.
Close all applications that are not being used.
Does scanning still take too long or freeze the computer?

Contact customer support.
The problem is solved.
Select a lower scan resolution.
Does scanning still take too long or freeze the computer?
Step 1 Check if an error message appears on the display.
Clear the error message.
Go to step 2.
Is there an error message on the printer display?
Go to step 3. Increase the scan resolution settings for a higher‑quality output.
Check the quality of the original document.
Is the quality of the original document satisfactory?
Go to step 4. See “Cleaning the scanner glass” on page 155.
Clean the scanner glass and the ADF glass using a clean, lint‑free cloth dampened with water.
Is the scanner glass clean?
Go to step 5. Place the document or photo facedown on the scanner glass in the upper left corner.
Check the placement of the document or photo.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Is the document or photo loaded correctly?
Go to step 6. See “Print quality problems” on page 206.
Send a print job, and then check for print quality problems.
Is the print quality satisfactory?
Go to step 7. Change the Content Type and Content Source settings to match the document being scanned.
Check the scan settings.
From the Scan screen, make sure the Content Type and Content Source settings are correct for the document being scanned.
Are the Content Type and Content Source settings correct for the document being scanned?

Problem solved. Contact customer support.
Increase the scan resolution settings for a higher‑quality output.
Did the increased resolution produce a higher‑quality output?
Check the placement of the document or photo.
Contact customer support.
Load the document or photo facedown on the scanner glass in the upper left corner.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Is the document or photo loaded correctly?
The problem is solved. Go to step 2.
a Turn on the printer. b Open a Web browser, and then type the printer IP address.
c Press Enter.
Does the Embedded Web Server open?
The problem is solved. Go to step 3.
Make sure the printer IP address is correct.
a View the printer IP address:
Does the Embedded Web Server open?

The problem is solved. Go to step 4.
Check if the network is working.
a Print a network setup page. b Check the first section of the network setup page and confirm that the
status is Connected.
Does the Embedded Web Server open?
The problem is solved. Go to step 5.
Check if the cable connections to the printer and print server are secure.
a Connect the cables properly. For more information, see the setup
documentation that came with the printer. b Open a Web browser, and then type the printer IP address.
c Press Enter.
Does the Embedded Web Server open?
The problem is solved. Contact your system support person.
Temporarily disable the Web proxy servers.
Proxy servers may block or restrict you from accessing certain Web sites including the Embedded Web Server.
Does the Embedded Web Server open?
When you contact customer support, you will need to be able to describe the problem you are experiencing, the message on the printer display, and the troubleshooting steps you have already taken to find a solution.
You need to know your printer model type and serial number. For more information, see the label at the back of the printer. The serial number is also listed on the menu settings page.
Lexmark has various ways to help you solve your printing problem. Visit the Lexmark Web site at http://support.lexmark.com, and then select one of the following:
Tech Library You can browse our library of manuals, support documentation, drivers, and other downloads to help you
solve common problems.
E-mail You can send an e-mail to the Lexmark team, describing your problem. A service representative will respond and provide you with information to solve your problem.

Live chat You can chat directly with a service representative. They can work with you to solve your printer problem or provide assistance through Assisted Service where the service representative can remotely connect to your computer through the Internet to troubleshoot problems, install updates, or complete other tasks to help you successfully use your Lexmark product.
Telephone support is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, visit http://support.lexmark.com.
Troubleshooting 239

Product name:
Machine type:
Model(s):
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
© 2012 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commerical Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
Lexmark MX310dn · June 2012

All licensing notices associated with this product can be viewed from the root directory of the installation software CD.
Lexmark, Lexmark with diamond design, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
All other trademarks are the property of their respective owners.
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232–3000

The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Values are subject to change. See www.lexmark.com for current values.
Ambient operating temperature 15.6 to 32.2°C (60 to 90°F)
Shipping and storage temperature ‑40 to 60°C (-40 to 140°F)
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products.
If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.

This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching the metal frame of the printer.
Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 7 milliwatt gallium arsenide laser operating in the wavelength of 655-675 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
A laser notice label may be affixed to this printer as shown:

NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, ze zařízení je vysíláno neviditelné laserové záření. Nevystavujte se působení laserového paprsku. FARE - Usynlig laserstråling, når patroner fjernes, og spærreanordningen er slået fra. Undgå at blive udsat for laserstrålen. GEVAAR - Onzichtbare laserstraling wanneer cartridges worden verwijderd en een vergrendeling wordt genegeerd. Voorkom blootstelling aan de laser.
ΚΙΝΔΥΝΟΣ - Έκλυση αόρατης ακτινοβολίας laser κατά την αφαίρεση των κασετών και την απασφάλιση της μανδάλωσης. Αποφεύγετε την έκθεση στην ακτινοβολία laser. VESZÉLY – Nem látható lézersugárzás fordulhat elő a patronok eltávolításakor és a zárószerkezet felbontásakor. Kerülje a lézersugárnak való kitettséget.
ОПАСНО! Невидимое лазерное излучение при извлеченных картриджах и снятии блокировки. Избегайте воздействия лазерных лучей. Pozor – Nebezpečenstvo neviditeľného laserového žiarenia pri odobratých kazetách a odblokovanej poistke. Nevystavujte sa lúčom.
危険 - カートリッジが取り外され、内部ロックが無効になると、見えないレーザー光が放射されます。 このレーザー光に当たらないようにしてください。
Power consumption
Product power consumption
The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs. 520 W
Copy The product is generating hard‑copy output from hard‑copy original documents.
Scan The product is scanning hard‑copy documents. 30 W
Ready The product is waiting for a print job. 12 W
Sleep Mode The product is in a high‑level energy‑saving mode. 5 W
Hibernate The product is in a low‑level energy‑saving mode. 0.5 W
Off The product is plugged into an electrical outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.

This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 30
By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 120 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
This product is designed with an ultra‑low power operating mode called Hibernate mode. When operating in Hibernate Mode, all other systems and devices are powered down safely.
The Hibernate mode can be entered in any of the following methods:
Factory default Hibernate Timeout for this product in all countries or regions except for EU countries and Switzerland
Factory default value for this product in EU countries or regions and Switzerland 3 days
The amount of time the printer waits after a job is printed before it enters Hibernate mode can be modified between one hour and one month.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the electrical outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
Disabled

This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and the ecodesign of energy- related products.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
This section contains regulatory information pertaining to products that contain telecommunication terminal equipment such as facsimile.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachments (ACTA). On the back of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to your telephone company.
This equipment uses the RJ-11C Universal Service Order Code (USOC) jack.
A plug and jack used to connect this equipment to the premises’ wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See your setup documentation for more information.
The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact your local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (for example, 03 is a REN of 0.3). For earlier products, the REN is shown separately on the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. You will also be advised of your right to file a complaint with the FCC.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
If you experience trouble with this equipment, for repair or warranty information, contact Lexmark International, Inc. at www.lexmark.com or your Lexmark representative. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

This equipment contains no user serviceable parts. For repair and warranty information, contact Lexmark International, Inc. See the previous paragraph for contact information.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. It is recommended that the customer install an appropriate AC surge arrestor in the AC outlet to which this device is connected. An appropriate AC surge arrestor is defined as one that is suitably rated, and certified by UL (Underwriter's Laboratories), another NRTL (Nationally Recognized Testing Laboratory), or a recognized safety certification body in the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless said message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)
See your user documentation in order to program this information into your fax machine.
This product meets the applicable Industry Canada technical specifications. The Ringer Equivalence Number (REN) is an indication of the maximum number of terminals allowed to be connected to a telephone interface. The terminus of an interface may consist of any combination of devices, subject only to the requirement that the sum of the RENs of all the devices does not exceed five. The modem REN is located on the rear of the equipment on the product labeling.
Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. It is recommended that the customer install an appropriate AC surge arrestor in the AC outlet to which this device is connected. An appropriate AC surge arrestor is defined as one that is suitably rated, and certified by UL (Underwriter’s Laboratories), another NRTL (Nationally Recognized Testing Laboratory), or a recognized safety certification body in the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges.
This equipment uses CA11A telephone jacks.
Ce produit est conforme aux spécifications techniques d’Industrie Canada. Le numéro REN (ringer equivalence number : numéro d’équivalence de sonnerie) fournit une indication du nombre maximum de terminaux pouvant être connectés à l’interface téléphonique. En bout de ligne, le nombre d’appareils qui peuvent être connectés n’est pas directement limité, mais la somme des REN de ces appareils ne doit pas dépasser cinq. Le numéro REN du modem est indiqué sur l’étiquette produit située à l’arrière de l’équipement.
Les compagnies de téléphone constatent que les surtensions électriques, en particulier celles dues à la foudre, entraînent d'importants dégâts sur les terminaux privés connectés à des sources d’alimentation CA. Il s’agit-là d’un problème majeur d’échelle nationale. En conséquence, il vous est recommandé de brancher un parasurtenseur dans

la prise de courant à laquelle l’équipement est connecté. Utilisez un parasurtenseur répondant à des caractéristiques nominales satisfaisantes et certifié par le laboratoire d’assureurs UL (Underwriter’s Laboratories), un autre laboratoire agréé de type NRTL (Nationally Recognized Testing Laboratory) ou un organisme de certification agréé dans votre région ou pays. Ceci prévient tout endommagement de l’équipement causé par les orages et autres surtensions électriques.
Cet équipement utilise des prises de téléphone CA11A.
The following are special conditions for the Facsimile User Instructions. The grant of a telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.
This equipment shall not be set up to make automatic calls to the Telecom's 111 Emergency Service.
This equipment may not provide for the effective hand-over of a call to another device connected to the same line.
This equipment should not be used under any circumstances that may constitute a nuisance to other Telecom customers.
Some parameters required for compliance with Telecom's telepermit requirements are dependent on the equipment associated with this device. The associated equipment shall be set to operate within the following limits for compliance to Telecom's specifications:
This product requires a Swiss billing tone filter (Lexmark part number 80D1877) to be installed on any line which receives metering pulses in Switzerland. The filter must be used, as metering pulses are present on all analog telephone lines in Switzerland.
Cet appareil nécessite l’utilisation d’un filtre de tonalité de facturation suisse (nº de référence Lexmark : 80D1877) devant être installé sur toute ligne recevant des impulsions de comptage en Suisse. Ce filtre doit être utilisé pour toute installation car ces impulsions existent sur toutes les lignes téléphoniques suisses.
Für dieses Produkt muss ein schweizerischer Billing Tone Filter zur Zählzeichenübertragung (Lexmark Teilenummer 80D1877) für jede Leitung installiert werden, über die in der Schweiz Zeitsteuertakte übertragen werden. Die Verwendung des Filters ist obligatorisch, da in allen analogen Telefonleitungen in der Schweiz Zeitsteuertakte vorhanden sind.

Questo prodotto richiede un filtro toni Billing svizzero, (codice Lexmark 80D1877) da installare su tutte le linee che ricevono impulsi remoti in Svizzera. È necessario utilizzare il filtro poiché gli impulsi remoti sono presenti su tutte le linee analogiche in Svizzera.
Products bearing the CE mark are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, radio equipment and telecommunications terminal equipment and on the ecodesign of energy‑related products.
Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
Refer to the table at the end of the Notices section for further compliance information.
This section contains the following regulatory information pertaining to wireless products that contain transmitters, for example, but not limited to, wireless network cards or proximity card readers.
Wireless‑equipped models contain the following modular component(s):
Lexmark Regulatory Type/Model LEX-M01-005; FCC ID:IYLLEXM01005; IC:2376A-M01005
The following notice is applicable if your printer has a wireless network card installed: The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.


This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, radio equipment and telecommunications terminal equipment and on the ecodesign of energy-related products.
Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
Products equipped with 2.4GHz Wireless LAN option are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment and on the ecodesign of energy-related products.
Compliance is indicated by the CE marking.
Operation is allowed in all EU and EFTA countries, but is restricted to indoor use only.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product may be used in the countries indicated in the table below.


AT BE BG CH CY CZ DE DK EE
EL ES FI FR HR HU IE IS IT
LI LT LU LV MT NL NO PL PT
Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.
Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.
Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.
Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.
Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.
Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.
Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky
príslušné ustanovenia smernice 1999/5/ES.
Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
STATEMENT OF LIMITED WARRANTY FOR LEXMARK LASER PRINTERS, LEXMARK LED PRINTERS, AND LEXMARK MULTIFUNCTION LASER PRINTERS
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country- specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Transfer/Transport Units, Paper Feed items, if any, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.

To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
As part of your warranty service and/or replacement, Lexmark may update the firmware in your printer to the latest version. Firmware updates may modify printer settings and cause counterfeit and/or unauthorized products, supplies, parts, materials (such as toners and inks), software, or interfaces to stop working. Authorized use of genuine Lexmark products will not be impacted.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.

Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.





[x]‑page jam, open tray [x].
Insufficient memory for Flash
incorrect characters print 200 incorrect margins on prints 210 jammed pages are not
[24y.xx] 177 Cartridge low [88.xy] 181 Cartridge nearly low [88.xy] 181 Cartridge very low, [x] estimated
Memory Defragment operation [37] 185 Insufficient memory to collate job
reprinted 199 job prints from wrong tray 200 job prints on wrong paper 200 jobs do not print 202 Large jobs do not collate 201 multiple‑language PDF files do not
[37] 185 Insufficient memory to support
pages remain [88.xy] 181 Cartridge, imaging unit mismatch
Resource Save feature [35] 185 Insufficient memory, some Held
[41.xy] 181 Change [paper source] to [custom
Jobs were deleted [37] 185 Insufficient memory, some held
string] load [paper orientation] 181 Change [paper source] to [custom
print 202 paper curl 211 paper frequently jams 199 print job takes longer than
jobs will not be restored [37] 185 Load [paper source] with [custom
type name] load [orientation] 182 Change [paper source] to [paper
string] [paper orientation] 187 Load [paper source] with [custom
expected 203 tray linking does not work 205 unexpected page breaks
size] load [orientation] 182 Change [paper source] to [paper
type name] [paper orientation] 187 Load [paper source] with [paper
type] [paper size] load [orientation] 182 Close flatbed cover and load
size] [paper orientation] 187 Load [paper source] with [paper
minimum clearances 9 moving 9, 163, 164 selecting a location 9 shipping 164 printer configurations 10
originals if restarting job [2yy.xx] 182 Close front door 182 Complex page, some data may not
type] [paper size] [paper orientation] 187 Load manual feeder with [custom
string] [paper orientation] 186 Load manual feeder with [custom
basic model 10 configured model 10 printer control panel
have printed [39] 183 Defective flash detected [51] 183 Error reading USB drive. Remove
type name] [paper orientation] 186 Load manual feeder with [paper
adjusting brightness 149 factory defaults, restoring 167 indicator light 13 Sleep button light 13 using 13 printer control panel, virtual display
USB. 183 Error reading USB hub. Remove
size] [paper orientation] 186 Load manual feeder with [paper
hub. 183 Fax memory full 183 Fax partition inoperative. Contact
type] [paper size] [paper orientation] 186 Maintenance kit low [80.xy] 188 Maintenance kit nearly low
system administrator. 183 Fax server 'To Format' not set up.
using the Embedded Web
Contact system administrator. 183 Fax Station Name not set up.
[80.xy] 188 Maintenance kit very low, [x]
Server 165 Printer had to restart. Last job may be incomplete. 190 printer information
estimated pages remain [80.xy] 188 Memory full [38] 188 Memory full, cannot print
Contact system administrator. 184 Fax Station Number not set up.
where to find 8 printer is printing blank pages 215 printer messages
Contact system administrator. 184 Imaging unit low [84.xy] 184 Imaging unit nearly low
faxes 188 Memory full, cannot send
[x]‑page jam, clear manual feeder.
faxes 188 Network [x] software error
[25y.xx] 178 [x]‑page jam, clear standard bin.
[84.xy] 184 Imaging unit very low, [x]
[54] 189 No analog phone line connected
[20y.xx] 175 [x]‑page jam, open automatic
estimated pages remain [84.xy] 184 Incorrect paper size, open [paper
to modem, fax is disabled. 189 Non‑Lexmark [supply type], see
feeder top cover. [28y.xx] 179 [x]‑page jam, open front door.
User’s Guide [33.xy] 189 Not enough free space in flash
[20y.xx] 171 [x]‑page jam, open rear door.
memory for resources [52] 189
[20y.xx] 174




configuration information 26 wireless network setup
using the Embedded Web
Server 28 wireless setup wizard
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.