
User's Guide
Machine type(s):
Model(s):
832, 835


Connect the power cord to a properly grounded electrical outlet that is near the product and easily accessible.
Do not place or use this product near water or wet locations.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
– Make sure to remove the topmost finisher first.
– To remove the finisher, hold the finisher on both sides, and then lift the latches to unlock the finisher. • If the printer does not have a caster base but is configured with optional trays, then remove the trays.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Use only the power cord provided with this product or the manufacturer's authorized replacement.
Safety information 6

This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a service representative.
SAVE THESE INSTRUCTIONS.
Safety information 7

Learning about the printer 8
Finding information about the printer

Learning about the printer 9
When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any options, then leave enough room for them also. It is important to:

Learning about the printer 10



4 Standard 250‑ or 550‑sheet tray (Tray 1)
1 Standard bin

Learning about the printer 11
The following illustration shows the maximum number of optional finishers and trays that are supported by the printer. For more information on other configurations, visit www.lexmark.com/multifunctionprinters.



Learning about the printer 12
The staple, hole punch finisher must not be combined with any other output option.
In a configuration with two or more optional finishers:
When using optional trays:
1 2 3 4 5

6 7 8 9 10


Learning about the printer 13
7 Back button Return to the previous screen.
8 Home button Go to the home screen.
9 Indicator light Check the status of the printer.
10 USB port Connect a flash drive to the printer.
The colors of the Sleep button and indicator lights on the printer control panel signify a certain printer status or condition.
Indicator light Printer status
Off The printer is off or in Hibernate mode.
Blinking green The printer is warming up, processing data, or printing.
Solid green The printer is on, but idle.
Blinking red The printer requires user intervention.
Sleep button light Printer status
Off The printer is off, idle or in Ready state.
Solid amber The printer is in Sleep mode.
Blinking amber The printer is entering or waking from Hibernate mode.
Blinking amber for 0.1 second, then goes completely off for 1.9 seconds in a slow, pulsing pattern
The printer is in Hibernate mode.
Use the To

Additional printer setup 14
Installing internal options
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Remove the controller board access cover.



Additional printer setup 15
2 Using a screwdriver, loosen the screws on the controller board shield.


3 Remove the shield.


Additional printer setup 16
4 Use the following illustration to locate the appropriate connector:

1 Lexmark Internal Solutions Port or printer hard disk connector
2 Option card connector
3 Memory card connector

Additional printer setup 17
5 Align the screws with the holes on the shield, and then reattach the shield.
6 Tighten the screws on the shield.

Additional printer setup 18
7 Reattach the access cover.


CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
An optional memory card can be purchased separately and attached to the controller board.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 14.
2 Unpack the memory card.
3 Align the notch (1) on the memory card with the ridge (2) on the connector.


Additional printer setup 19
4 Push the memory card straight into the connector, and then push the card toward the controller board wall until it clicks into place.

5 Reattach the controller board shield, and then the controller board access cover.
The controller board supports one optional Lexmark Internal Solutions Port (ISP).
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 14.
2 If an optional printer hard disk is installed, then remove the printer hard disk first.
For more information, see “Removing a printer hard disk” on page 29.

Additional printer setup 20
3 Unpack the ISP kit.


2 Screw for attaching the plastic bracket to the ISP
3 Screws for attaching the ISP mounting bracket to the controller board shield
4 Remove the metal cover from the ISP opening. a Loosen the screw.

b Lift the metal cover, and then pull it out completely.
1 ISP solution · 4 Plastic bracket

Additional printer setup 21



5 Align the posts of the plastic bracket with the holes on the controller board cage, and then press the plastic bracket on the controller board cage until it clicks into place. Make sure the cables are neatly tucked under the plastic bracket.


6 Install the ISP on the plastic bracket.


Additional printer setup 22
7 Lower the ISP toward the plastic bracket until the ISP is seated between the guides of the plastic bracket.


8 Use the provided thumbscrew for the ISP to attach the plastic bracket to the ISP.


Additional printer setup 23
9 Attach the two provided screws to secure the ISP mounting bracket to the controller board shield.


10 Tighten the thumbscrew that is attached to the ISP.
11 Connect the ISP solution interface cable into the receptacle of the controller board.



Additional printer setup 24
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 14.
2 Unpack the optional card.
3 Holding the card by its sides, align the plastic pins (1) on the card with the holes (2) on the controller board.


4 Push the card firmly into place as shown in the illustration.


Additional printer setup 25
5 Close the controller board access door.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 14.
2 Unpack the printer hard disk.

Additional printer setup 26
3 Locate the appropriate connector on the controller board cage.



Additional printer setup 27
To install a printer hard disk onto the ISP:
a Remove the screws attached to the printer hard disk mounting bracket, and then remove the bracket.

b Align the standoffs of the printer hard disk to the holes in the ISP, and then press the printer hard disk down
until the standoffs are in place.
Installation warning: Hold only the edges of the printed circuit board assembly. Do not touch or press on the center of the printer hard disk. Doing so may cause damage.

c Insert the plug of the printer hard disk interface cable into the receptacle of the ISP.

Additional printer setup 28

4 Align the standoffs of the printer hard disk to the holes in the controller board cage, and then press the printer hard disk down until the standoffs are in place.
Installation warning: Hold only the edges of the printed circuit board assembly. Do not touch or press on the center of the printer hard disk. Doing so may cause damage.

5 Insert the plug of the printer hard disk interface cable into the receptacle of the controller board.

Additional printer setup 29


CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.

Additional printer setup 30
1 Access the controller board.
For more information, see “Accessing the controller board” on page 14.
2 Unplug the printer hard disk interface cable from the controller board, leaving the cable attached to the printer hard disk. To unplug the cable, squeeze the paddle at the plug of the interface cable to disengage the latch before pulling out the cable.
3 Remove the screws holding the printer hard disk in place.



Additional printer setup 31
4 Remove the printer hard disk.
5 Set aside the printer hard disk.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Install the printer and any hardware options you have purchased in the following order:
For more information on installing a caster base, optional 550‑ or 250‑sheet tray, spacer, or 2100‑sheet tray, see the setup sheet that came with the option.

Additional printer setup 32
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer using the power switch, and then unplug the power cord from the electrical outlet.


2 Unpack the optional tray, and then remove all packing material.
3 Pull out the tray completely from the base.


4 Remove any packing material from inside the tray.
5 Insert the tray into the base.
6 Place the tray near the printer.
7 Align the optional tray with the caster base.

Additional printer setup 33

8 Align the printer with the tray, and then slowly lower the printer into place.

Additional printer setup 34

9 Connect the power cord to the printer, then to a properly grounded electrical outlet, and then turn on the printer.

Additional printer setup 35



To uninstall the optional trays, slide the latch on the right side of the printer toward the front of the printer until it clicks into place, and then remove stacked trays one at a time from the top to the bottom.
Connect the printer to the computer using a USB cable or Ethernet cable.
Make sure to match the following:

Additional printer setup 36




1 Parallel port Connect the printer to a computer.
2 USB port Attach an optional wireless network adapter.
3 Ethernet port Connect the printer to a network.
4 USB printer port Connect the printer to a computer.
5 Security slot Attach a lock that will secure the controller board.
6 Printer power cord socket Connect the printer to a properly grounded electrical outlet.
After attaching the Ethernet cable and power cord, neatly tuck the cables in the channels at the back of the printer.

Additional printer setup 37


2 Do either of the following: • If you are using the Software and Documentation CD, then insert the CD and wait for the installation dialog to appear. If the installation dialog does not appear, then do the following:

Additional printer setup 38
From the Search charm, type run, and then navigate to: Apps list > Run > type D:\setup.exe > OK.
, or click Start and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
c Press Enter, or click OK.
Click the CD icon on the desktop. • If you are using the downloaded software installer from the Web, then double‑click the installer that you have saved in your computer. Wait for the Select Installation Type dialog to appear, and then click Install.
3 Click Install, and then follow the instructions on the computer screen.
When any hardware options are installed, you may need to manually add the options in the printer driver to make them available for use.
1 Open the printers folder.
From the Search charm, type run, and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
4 Click the Configuration tab.
a Click · In Windows 8 · a Click

Additional printer setup 39
6 Click Apply.
2 Add any installed hardware options, and then click OK.
To configure your printer to connect to an Ethernet network, organize the following information before you begin:
You will need an Ethernet cable to connect the printer to the network and an available port where the printer can physically connect to the network. Use a new network cable when possible to avoid potential problems caused by a damaged cable.

Additional printer setup 40
2 Do either of the following: • If you are using the Software and Documentation CD, then insert the CD and wait for the installation dialog to appear. If the installation dialog does not appear, then do the following:
From the Search charm, type run, and then navigate to: Apps list > Run > type D:\setup.exe > OK
In Windows 7 or earlier
, or click Start and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
c Press Enter, or click OK.
3 Click Install, and then follow the instructions on the computer screen.
4 Select Ethernet connection, and then click Continue.
5 Attach the Ethernet cable when instructed to do so.
6 Select the printer from the list, and then click Continue.
7 Follow the instructions on the computer screen.
1 Allow the network DHCP server to assign an IP address to the printer.
In Windows 8 · a Click

Additional printer setup 41
3 Install the printer driver on the computer. a Insert the Software and Documentation CD, and then double‑click the installer package for the printer. b Follow the instructions on the computer screen.
c Select a destination, and then click Continue. d From the Easy Install screen, click Install. e Type the user password, and then click OK.
All the necessary applications are installed on the computer. f Click Close when installation is complete.
4 Add the printer. • For IP printing: a From the Apple menu, navigate to either of the following:
– System Preferences > Print & Scan – System Preferences > Print & Fax b Click +.
c If necessary, click Add Printer or Scanner or Add Other Printer or Scanner. d Click the IP tab. e Type the printer IP address in the address field, and then click Add. • For AppleTalk printing:
– Make sure AppleTalk is activated on your printer. – This feature is supported only in Mac OS X version 10.5. a From the Apple menu, navigate to:
System Preferences > Print & Fax b Click +, and then navigate to:
AppleTalk > select your printer > Add
Make sure you have the following information before setting up the printer on a wireless network:
Some ad hoc networks will also require the automatic setting. Check with your system support person if you are not sure which channel to select.

Additional printer setup 42
If your network uses more than one WEP key, then enter up to four in the provided spaces. Select the key currently in use on the network by selecting the default WEP transmit key. – WPA or WPA2 preshared key or passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network. – 802.1X–RADIUS
If you are installing the printer on an 802.1X network, then you may need the following:
If your wireless network does not use any type of security, then you will not have any security information.
– If you do not know the SSID of the network that your computer is connected to, then launch the wireless utility
of the computer network adapter, and then look for the network name. If you cannot find the SSID or the security information for your network, then see the documentation that came with the access point, or contact your system support person. – To find the WPA/WPA2 preshared key or passphrase for the wireless network, see the documentation that
came with the access point, see the Embedded Web Server associated with the access point, or consult your system support person.
Before you begin, make sure that:
> Settings > > Network/Ports > > Active NIC > > Auto >
1 From the printer control panel, navigate to:
> Settings > > Network/Ports > > Network [x] > > Network [x] Setup > > Wireless > >
Wireless Connection Setup >
2 Select a wireless connection setup.

Additional printer setup 43
Search for networks Show available wireless connections.
Enter a network name Manually type the SSID.
Wi‑Fi Protected Setup Connect the printer to a wireless network using Wi‑Fi Protected Setup.
3 Press , and then follow the instructions on the printer display.
Before you begin, make sure that:
1 From the printer control panel, navigate to:
> Settings > >Network/Ports > > Network [x] > > Network [x] Setup > > Wireless > >
Wireless Connection Setup > > Wi‑Fi Protected Setup > > Start Push Button Method >
2 Follow the instructions on the printer display.
1 From the printer control panel, navigate to:
> Settings > >Network/Ports > > Network [x] > > Network [x] Setup > > Wireless > >
Wireless Connection Setup > > Wi‑Fi Protected Setup > > Start PIN Method >
2 Copy the eight‑digit WPS PIN.
3 Open a Web browser, and then type the IP address of your access point in the address bar.
4 Access the WPS settings. For more information, see the documentation that came with your access point.
5 Enter the eight‑digit PIN, and then save the setting.
Use To

Additional printer setup 44
Before you begin, make sure that:
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Network/Ports > Wireless.
3 Modify the settings to match the settings of your access point (wireless router).
4 Click Submit.
5 Turn off the printer, and then disconnect the Ethernet cable. Then wait for at least five seconds, and then turn the printer back on.
6 To verify if your printer is connected to the network, print a network setup page. Then in the Network Card [x] section, see if the status is Connected.
When a new Lexmark Internal Solutions Port (ISP) is installed in the printer, the printer configurations on computers that access the printer must be updated since the printer will be assigned a new IP address. All computers that access the printer must be updated with this new IP address.
1 Open a Web browser, and then type the printer IP address in the address field.

Additional printer setup 45
2 Open the printers folder.
From the Search charm, type Run and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
, or click Start and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
4 Click the Ports tab.
5 Select the port from the list, and then click Configure Port.
6 Type the new IP address in the “Printer Name or IP Address” field.
7 Click OK > Close.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Add the printer. • For IP printing: a From the Apple menu, navigate to either of the following:
– System Preferences > Print & Scan – System Preferences > Print & Fax b Click +.
c Click the IP tab. d Type the printer IP address in the address field, and then click Add. • For AppleTalk printing:
In Windows 8 · a Click

Additional printer setup 46
– Make sure AppleTalk is activated on your printer. – This feature is supported only in Mac OS X version 10.5. a From the Apple menu, navigate to:
System Preferences > Print & Fax b Click +, and then navigate to:
AppleTalk > select the printer > Add
Use serial printing to print when the computer is far from the printer or to print at a reduced speed.
After installing the serial or communication (COM) port, configure the printer and the computer. Make sure you have connected the serial cable to the COM port on your printer.
1 Set the parameters in the printer. a From the printer control panel, navigate to the menu for the port settings. b Locate the menu for the serial port settings, and then adjust the settings, if necessary.
c Save the modified settings, and then print a menu settings page.
2 Install the printer driver. a Obtain a copy of the software installer package.
From the Search charm type run, and then navigate to: Apps list > Run > type D:\setup.exe > OK
, or click Start and then click Run. 2 In the Start Search or Run dialog, type D:\setup.exe. 3 Press Enter or click OK.
1 Click

Additional printer setup 47
d Follow the instructions on the computer screen. e Select Advanced, and then click Continue.
f From the Configure Printer Connection dialog, select a port. g If the port is not in the list, then click Refresh, or navigate to:
Add port > select a port type > enter the necessary information > OK h Click Continue > Finish.
3 Set the COM port parameters.
After installing the printer driver, set the serial parameters in the COM port assigned to the printer driver.
From the Search charm, type run and then navigate to: Apps list > Run > type devmgmt.msc > OK
, or click Start and then click Run. 2 In the Start Search or Run dialog, type devmgmt.msc. 3 Press Enter or click OK. b Double‑click Ports (COM & LPT) to expand the list of available ports.
c Do either of the following:
Check the serial heading of the menu settings page for the printer settings. f Click OK, and then close all the dialogs. g Print a test page to verify printer installation.
Print a menu settings page to review the current menu settings and to verify if the printer options are installed correctly.
From the printer control panel, navigate to:
> Settings > >Reports > > Menu Settings Page >
1 Click

Additional printer setup 48
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the printer control panel, navigate to:
> Settings > > Reports > > Network Setup Page >
2 Check the first section of the network setup page, and then confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult your system support person for a solution, and then print another network setup page.

Loading paper and specialty media 49
The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 163 and “Storing paper” on page 73.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Paper Size/Type >
2 Press the up or down arrow button to select the tray or feeder, and then press .
3 Press the up or down arrow button to select the paper size, and then press .
4 Press the up or down arrow button to select the paper type, and then press to change the settings.
The Universal paper size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus.
From the printer control panel, navigate to:
> Settings > > Paper Menu > > Universal Setup > > Units of Measure > > select unit of
1 Pull out the tray.
measure >

Loading paper and specialty media 50

2 Squeeze and slide the width guide to the correct position for the size of the paper being loaded until it clicks into place.


Loading paper and specialty media 51

3 Unlock the length guide, and then squeeze and slide the guide to the correct position for the size of the paper being loaded.


Loading paper and specialty media 52

4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper stack with the printable side facedown.

Without an optional staple finisher With an optional staple finisher

Loading paper and specialty media 53

Without an optional staple finisher With an optional staple finisher



Loading paper and specialty media 54


Loading paper and specialty media 55

6 For custom‑ or Universal‑size paper, adjust the paper guides to lightly touch the sides of the stack, and then lock the length guide.
7 Insert the tray.

8 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.

Loading paper and specialty media 56
1 Pull out the tray.
2 Adjust the width and length guides.
Loading A5‑size paper
a Pull up and slide the width guide to the position for A5.



Loading paper and specialty media 57
b Squeeze and slide the length guide to the position for A5 until it clicks into place.


c Remove the A5 length guide from its holder.


d Insert the A5 length guide into its designated slot.



Loading paper and specialty media 58
Loading A4‑, letter‑, legal‑, oficio‑, and folio‑size paper
a Pull up and slide the width guide to the correct position for the size of the paper being loaded.


b If the A5 length guide is still attached to the length guide, then remove it from its place. If the A5 length guide
is not attached, then proceed to step d.


Loading paper and specialty media 59
c Put the A5 length guide in its holder.
d Squeeze the length guide and slide it to the correct position for the size of the paper being loaded until it clicks
into place.


A4 A5

Loading paper and specialty media 60
3 Flex and fan the sheets to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

4 Load the paper stack with the printable side facedown.

Without an optional staple finisher With an optional staple finisher

Loading paper and specialty media 61



5 Insert the tray.

Loading paper and specialty media 62

6 From the printer control panel, set the size and type in the Paper menu to match the paper loaded in the tray.
1 Pull down the multipurpose feeder door.

B5
EXEC
A4 A5

Loading paper and specialty media 63
2 Pull the multipurpose feeder extender.

LTR
B5
EXEC
3 Slide the width guide to the correct position for the size of the paper being loaded.

A4 A5
EXEC
B5

Loading paper and specialty media 64

B5
4 Prepare the paper or specialty media for loading. • Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper or specialty media.

Loading paper and specialty media 65
Without an optional staple finisher With an optional staple finisher

ABC
One‑sided printing
One‑sided printing
ABC
Two‑sided (duplex) printing
Two‑sided (duplex) printing
One‑sided printing Two‑sided printing


Loading paper and specialty media 66


6 For custom- or Universal-size paper, adjust the width guides to lightly touch the sides of the stack.
7 From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu.
4 Click Submit.

Loading paper and specialty media 67
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Select a custom name, and then type a new custom paper type name.
4 Click Submit.
5 Click Custom Types, and then verify if the new custom paper type name has replaced the custom name.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Custom Names
2 Select a custom name, and then type a new custom paper type name.
3 Press .
4 Press Custom Types, and then verify if the new custom paper type name has replaced the custom name.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.

Loading paper and specialty media 68
3 Type a name for the paper type, and then click Submit.
4 Select a custom type, and then verify that the correct paper type is associated with the custom name.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Custom Names
2 Type a name for the paper type, and then press .
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Types.
3 Select a custom paper type name, and then select a paper type.
4 Click Submit.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Custom Types
2 Select a custom paper type name, and then select a paper type.
3 Press .

Paper and specialty media guide 69
Card stock is heavy, single‑ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly affect print quality.

Paper and specialty media guide 70
The following paper characteristics affect print quality and reliability. Consider these factors before printing on them:
The printer trays and multipurpose feeder can automatically feed paper weights between 60–176 g/m2 (16–47‑lb) grain long paper. The 2100‑sheet tray can automatically feed paper weights up to 60–135 g/m2 (16–36‑lb) grain long paper. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, and may cause jams.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.
Paper smoothness directly affects print quality. If paper is too rough, toner cannot fuse to it properly. If paper is too smooth, it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; smoothness between 150 and 250 Sheffield points produces the best print quality.
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.
Store paper in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extend the time several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.

Paper and specialty media guide 71
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60–176 g/m2 (16–47‑lb) paper, grain long paper is recommended.
Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability, resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton can negatively affect paper handling.
Using the appropriate paper prevents jams and helps ensure trouble‑free printing.
To help avoid paper jams and poor print quality:
As an environmentally conscientious company, Lexmark supports the use of recycled paper produced specifically for use in laser (electrophotographic) printers.
While no blanket statement can be made that all recycled paper will feed well, Lexmark consistently tests papers that represent recycled cut size copier papers available on the global market. This scientific testing is conducted with rigor and discipline. Many factors are taken into consideration both separately and as a whole, including the following:

Paper and specialty media guide 72
Recycled papers are better than ever; however, the amount of recycled content in a paper affects the degree of control over foreign matter. And while recycled papers are one good path to printing in an environmentally responsible manner, they are not perfect. The energy required to de-ink and deal with additives such as colorants and “glue” often generates more carbon emissions than does normal paper production. However, using recycled papers enables better resource management overall.
Lexmark concerns itself with the responsible use of paper in general based on life cycle assessments of its products. To gain a better understanding of the impact of printers on the environment, the company commissioned a number of life cycle assessments and found that paper was identified as the primary contributor (up to 80%) of carbon emissions caused throughout the entire life of a device (from design to end-of-life). This is due to the energy-intensive manufacturing processes required to make paper.
Thus, Lexmark seeks to educate customers and partners on minimizing the impact of paper. Using recycled paper is one way. Eliminating excessive and unnecessary paper consumption is another. Lexmark is well-equipped to help customers minimize printing and copying waste. In addition, the company encourages purchasing paper from suppliers who demonstrate their commitment to sustainable forestry practices.
Lexmark does not endorse specific suppliers, although a converter’s product list for special applications is maintained. However, the following paper choice guidelines will help alleviate the environmental impact of printing:
1 Minimize paper consumption.
2 Be selective about the origin of wood fiber. Buy from suppliers who carry certifications such as the Forestry Stewardship Council (FSC) or The Program for the Endorsement of Forest Certification (PEFC). These certifications guarantee that the paper manufacturer uses wood pulp from forestry operators that employ environmentally and socially responsible forest management and restoration practices.
3 Choose the most appropriate paper for printing needs: normal 75 or 80 g/m2 certified paper, lower weight paper, or recycled paper.
Test results indicate that the following paper types are at risk for use with laser printers:

Paper and specialty media guide 73
For more information about Lexmark, visit www.lexmark.com. General sustainability-related information can be found at the Environmental Sustainability link.
Use these paper storage guidelines to help avoid jams and uneven print quality:
The following tables provide information on standard and optional paper sources and the sizes, types, and weights of paper they support.
The printer engine supports 60–176‑g/m2 (16–47‑lb) paper weights.
Paper type 250‑ or 550‑sheet trays
2100‑sheet tray Multipurpose feeder Duplex
Paper labels X X
Vinyl Labels X X
* Print on transparencies by batches of only up to 20 to prevent them from sticking together. For more information, see “Tips on using transparencies” on page 70.

Paper and specialty media guide 74
Paper size1 Dimensions Standard or optional 250‑ or 550‑sheet trays
Optional 2100‑sheet tray Multipurpose feeder
A4 210 x 297 mm (8.3 x 11.7 in.)
A5 148 x 210 mm (5.8 x 8.3 in.)
A6 105 x 148 mm (4.1 x 5.8 in.)
JIS B5 182 x 257 mm (7.2 x 10.1 in.)
Letter 216 x 279 mm (8.5 x 11 in.)
Legal 216 x 356 mm (8.5 x 14 in.)
Executive 184 x 267 mm (7.3 x 10.5 in.)
Oficio 216 x 340 mm (8.5 x 13.4 in.)
Folio 216 x 330 mm (8.5 x 13 in.)
Statement 140 x 216 mm (5.5 x 8.5 in.)
Universal2 105 x 148 mm to 216 x 356 mm (4.13 x 5.83 in. to 8.5 x 14 in.)
70 x 127 mm to 216 x 356 mm (2.76 x 5 to 8.5 x 14 in.)
1 If your preferred default paper size cannot be set in the printer control panel, then you may select common paper sizes that correspond to the position of the length guide in the tray from the Paper Size/Type menu. If the paper size is not available, then select Universal or turn off tray size sensing. For more information, contact customer support.
2 To support two‑sided (duplex) printing, the Universal width must be between 105 mm (4.13 inches) and 216 mm (8.5 inches); the Universal length must be between 148 mm (5.83 inches) and 356 mm (14 inches).
Duplex

Paper and specialty media guide 75

Paper size 4‑bin mailbox Output expander and
1 The finisher stacks the paper but does not staple or punch holes in it.
2 The finisher stacks and staples the paper but does not punch holes in it.
3 The finisher staples the paper if it is loaded long edge first.
4 The finisher staples the paper if its width is from 8.27 to 8.54 inches but does not punch holes in it.

Paper type Paper weight 4‑bin mailbox Output expander and high‑capacity
1 The finisher stacks the paper but does not staple or punch holes in it.
2 Print on transparencies by batches of only up to 20 to prevent them from sticking together. For more information, see “Tips on using transparencies” on page 70.

Paper and specialty media guide 76

Paper type Paper weight 4‑bin mailbox Output expander and high‑capacity
1 The finisher stacks the paper but does not staple or punch holes in it.
2 Print on transparencies by batches of only up to 20 to prevent them from sticking together. For more information, see “Tips on using transparencies” on page 70.

Paper and specialty media guide 77
Paper type Paper weight 4‑bin mailbox Output expander and high‑capacity
Staple finisher Staple, hole punch
Colored Paper 90–176 g/m2
1 The finisher stacks the paper but does not staple or punch holes in it.
2 Print on transparencies by batches of only up to 20 to prevent them from sticking together. For more information, see “Tips on using transparencies” on page 70.

Printing a document
1 From the Paper menu on the printer control panel, set the paper type and size to match the paper loaded.
2 Send the print job:
a With a document open, click File > Print. b Click Properties, Preferences, Options, or Setup.
c Adjust the settings, if necessary. d Click OK > Print.
a Customize the settings in the Page Setup dialog if necessary:
1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the paper loaded. 3 Click OK. b Customize the settings in the Page Setup dialog if necessary:
1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options. 2 From the Print dialog and pop‑up menus adjust the settings if necessary.
1 Open a Web browser, and then type the IP address of the printer in the address field.
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the toner darkness, and then click Submit.
Printing 78

1 From the printer control panel, navigate to:
> Settings > > Print Settings > > Quality Menu > > Toner Darkness
2 Adjust the toner darkness, and then press .
1 Insert a flash drive into the USB port.


Printing 79

2 From the printer control panel, select the document you want to print.
3 Press the left or right arrow button to specify the number of copies for printing, and then press .
Recommended flash drives File type
Documents:
Printing 80

To download a compatible mobile printing application, visit www.lexmark.com/mobile.
1 From the printer control panel, navigate to:
> Settings > > Security > > Confidential Print > select the print job type
Print job type Description
Max Invalid PIN Limits the number of times an invalid PIN can be entered.
Confidential Job Expiration Lets you hold print jobs in the computer until you enter the PIN from the printer control panel.
Repeat Job Expiration Lets you print and store print jobs in the printer memory for reprinting.
Verify Job Expiration Lets you print one copy of a print job while the printer holds the remaining copies. It allows you to examine if the first copy is satisfactory. The print job is automatically deleted from the printer memory once all copies are printed.
Reserve Job Expiration Lets you store print jobs for printing at a later time. The print jobs are held until deleted from the Held Jobs menu.
2 Press .
Printing 81

1 With a document open, click File > Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click Print and Hold.
4 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
5 Click OK or Print.
1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2 From the print options or Copies & Pages pop‑up menu, choose Job Routing.
3 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
4 Click OK or Print.
Printing 82

For more information on printing information pages, see “Printing a menu settings page” on page 47 and “Printing a network setup page” on page 48.
1 From the printer control panel, navigate to:
> Settings > > Reports > > Print Fonts
2 Press the up or down arrow button to select the font setting.
3 Press .
From the printer control panel, navigate to:
> Settings > Reports > > Print Directory >
From the printer control panel, press > .
1 Open the printers folder.
From the Search charm, type run, and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
Printing 83 · In Windows 8 · a Click

2 Double‑click the printer icon.
3 Select the print job you want to cancel.
4 Click Delete.
2 From the printer window, select the print job you want to cancel, and then delete it.
Printing 84

Understanding printer menus 85
Menus list
Paper Menu Reports Network/Ports
Default Source Paper Size/Type
Menu Settings Page Device Statistics
Network Setup Page 1
Parallel [x] Serial [x]
Universal Setup Bin Setup
Erase Temporary Data Files
Set Date and Time
Media Guide Print Defects Guide
1 Depending on the printer setup, this menu item appears as Network Setup Page or Network [x] Setup Page.
2 Depending on the printer setup, this menu item appears as Standard Network or Network [x].

Understanding printer menus 86
Set a default paper source for all print jobs.
Tray [x] MP Feeder Manual Paper
Specify the paper size loaded in each tray.
A4 A5 A6 JIS‑B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal

Understanding printer menus 87
Specify the type of paper loaded in each tray.
Plain Paper Card Stock Transparency Recycled Labels Vinyl Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Specify the paper size loaded in the multipurpose feeder.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the paper type loaded in the multipurpose feeder.
Plain Paper Card Stock Transparency Recycled Labels Vinyl Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]

Understanding printer menus 88
Specify the size of the paper being manually loaded.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the paper type being manually loaded.
Plain Paper Card Stock Transparency Recycled Labels Vinyl Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Determine when the printer selects paper from the multipurpose feeder.

Understanding printer menus 89
Substitute a specified paper size if the requested paper size is not available.
Off Statement/A5 Letter/A4 All Listed
Specify the relative texture of the plain paper loaded in a specific tray.
Specify the relative texture of the card stock loaded in a specific tray.
Specify the relative texture of the transparencies loaded in a specific tray.
Specify the relative texture of the recycled paper loaded in a specific tray.
Specify the relative texture of the labels loaded in a specific tray.
Specify the relative texture of the vinyl labels loaded in a specific tray.
Specify the relative texture of the bond paper loaded in a specific tray.

Understanding printer menus 90
Specify the relative texture of the letterhead loaded in a specific tray.
Specify the relative texture of the preprinted paper loaded in a specific tray.
Specify the relative texture of the colored paper loaded in a specific tray.
Specify the relative texture of the light paper loaded in a specific tray.
Specify the relative texture of the heavy paper loaded in a specific tray.
Specify the relative texture of the rough or cotton paper loaded in a specific tray.
Specify the relative texture of the custom paper loaded in a specific tray.
Specify the relative weight of the plain paper loaded.
Specify the relative weight of the card stock loaded.
Specify the relative weight of the transparencies loaded.

Understanding printer menus 91
Specify the relative weight of the recycled paper loaded.
Specify the relative weight of the labels loaded.
Specify the relative weight of the vinyl labels loaded.
Specify the relative weight of the bond paper loaded.
Specify the relative weight of the letterhead loaded.
Specify the relative weight of the preprinted paper loaded.
Specify the relative weight of the colored paper loaded.
Specify that the weight of the paper loaded is light.
Specify that the weight of the paper loaded is heavy.
Specify the relative weight of the cotton or rough paper loaded.
Specify the relative weight of the custom paper loaded.

Understanding printer menus 92
Determine and set two-sided printing for all print jobs with Card Stock as the paper type.
Determine and set two-sided printing for all print jobs with Recycled as the paper type.
Determine and set two-sided printing for all print jobs with Labels as the paper type.
Determine and set two-sided printing for all print jobs with Vinyl Labels as the paper type.
Determine and set two-sided printing for all print jobs with Bond as the paper type.
Determine and set two-sided printing for all print jobs with Letterhead as the paper type.
Determine and set two-sided printing for all print jobs with Preprinted as the paper type.
Determine and set two-sided printing for all print jobs with Colored as the paper type.
Determine and set two-sided printing for all print jobs with Light as the paper type.
Determine and set two-sided printing for all print jobs with Heavy as the paper type.
Determine and set two-sided printing for all print jobs with Rough or Cotton as the paper type.

Understanding printer menus 93
Determine and set two-sided printing for all print jobs with Custom [x] as the paper type.
Associate a paper or specialty media type with a factory default custom type name or a user‑defined custom name created from the Embedded Web Server or from MarkVisionTM Professional.
Paper Card Stock Transparency Rough/Cotton Labels Vinyl Labels
Specify a paper type when Recycled is selected in other menus.
Paper Card Stock Transparency Rough/Cotton Labels Vinyl Labels
Identify the units of measure.

Understanding printer menus 94
Set the portrait width.
3–8.5 inches 76–216 mm
Set the portrait height.
3–14.17 inches 76–360 mm
Specify the feed direction if the paper can be loaded in either direction.
Short Edge Long Edge
Specify the default bin.
Standard Bin Bin [x]

Understanding printer menus 95
Specify configuration options for bins.
Mailbox Link Mail Overflow Link Optional Type Assignment
Specify an alternative bin when a designated bin is full.
Standard Bin Bin [x]
Select a bin for each supported paper type.
Plain Paper Bin Card Stock Bin Transparency Bin Recycled Bin Labels Bin Vinyl Labels Bin Bond Bin Letterhead Bin Preprinted Bin Colored Bin Light Paper Bin Heavy Paper Bin Rough/Cotton Bin Custom [x] Bin
For each type, select the following options:
Disabled Standard Bin Bin [x]

Understanding printer menus 96
Menu Settings Page Print a report containing information about the paper loaded in trays, installed memory, total page count, alarms, timeouts, printer control panel language, TCP/IP address, status of supplies, status of the network connection, and other information.
Device Statistics Print a report containing printer statistics such as supply information and details about printed pages.
Stapler Test Print a report that confirms that the staple finisher is functioning properly.
Network Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address information.
Network [x] Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address information.
Profiles List Print a list of profiles stored in the printer.
Print a report of all the fonts available for the printer language currently set in the printer.
PCL Fonts PostScript Fonts
Print Directory Print a list of all the resources stored in an optional flash memory card or printer hard disk.
Asset Report Print a report containing printer asset information, such as serial number and model name.
Use To · Print Fonts
![Page 97 of the Lexmark MS710 user manual — Standard Network or Network [x] menu](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-97.webp?w=400)
Understanding printer menus 97
Allow the printer to connect to a network.
Auto [list of available network cards]
Set the printer to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.

Understanding printer menus 98
Set the size of the network input buffer.
Auto 3KB to [maximum size allowed]
Temporarily store print jobs in the printer hard disk before printing. This menu only appears when a formatted disk is installed.
Set the printer to process Macintosh binary PostScript print jobs.
Standard Network Setup OR Network [x] Setup
Show and set the printer network settings.
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
To access the menu, navigate to either of the following:
Print Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address.

Understanding printer menus 99
To access the menu, navigate to either of the following:
View the connection status of the wireless network adapter.
View Card Speed View the speed of an active wireless network adapter.
View the network addresses.
Job Timeout 0, 10–225 seconds Set the amount of time it takes for a network print job to be canceled.
Allow the printer to print a banner page.
To access the menu, navigate to either of the following:
Set Hostname Set the current TCP/IP host name.
IP Address View or change the current TCP/IP address.
Netmask View or change the current TCP/IP netmask.
Gateway View or change the current TCP/IP gateway.
Specify the DHCP address and parameter assignment.

Understanding printer menus 100
Specify the RARP address assignment setting.
Specify the BOOTP address assignment setting.
Specify the Zero Configuration Networking setting.
Enable the built-in FTP server, which lets you send files to the printer using File Transfer Protocol.
Enable the built-in Web server (Embedded Web Server). When enabled, the printer can be monitored and managed remotely using a Web browser.
WINS Server Address View or change the current WINS server address.
View or change the current DDNS setting.
View or change the current mDNS setting.
DNS Server Address View or change the current DNS server address.
Backup DNS Server Address View or change the backup DNS server addresses.
Backup DNS Server Address 2
Backup DNS Server Address 3
View or change the current HTTPS setting.
To access the menu, navigate to either of the following:

Understanding printer menus 101
Enable IPv6 in the printer.
Specify whether or not the wireless network adapter accepts the automatic IPv6 address configuration entries provided by a router.
View Hostname Set the host name.
Enable DHCPv6 in the printer.
To access the menu, navigate to:
Network/Ports > Network [x] > Network [x] Setup > Wireless
Wi‑Fi Protected Setup
Establish a wireless network and enable network security.
Start Push Button Method Start PIN Method
Enable/Disable WPS Auto‑detection
Automatically detect the connection method that an access point with WPS uses—Start Push Button Method or Start PIN Method.
Specify the network mode.
Specify the wireless standard for the wireless network.
802.11b/g 802.11b/g/n

Understanding printer menus 102
Choose Network Select an available network for the printer to use.
View Signal Quality View the quality of the wireless connection.
View Security Mode View the encryption method for the wireless network.
To access the menu, navigate to either of the following:
Enable or disable AppleTalk support.
View Name Show the assigned AppleTalk name.
View Address Show the assigned AppleTalk address.
Provide a list of AppleTalk zones available on the network.
[list of zones available on the network]
Set the printer to automatically switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language.

Understanding printer menus 103
Set the printer to automatically switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.
Set the size of the USB input buffer.
Disabled Auto 3K to [maximum size allowed]
Temporarily store print jobs in the printer hard disk before printing.
Set the printer to process Macintosh binary PostScript print jobs.
![Page 104 of the Lexmark MS710 user manual — Parallel [x] menu](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-104.webp?w=400)
Understanding printer menus 104
Set the network address information for an external print server.
yyy.yyy.yyy.yyy
Set the netmask information for an external print server.
yyy.yyy.yyy.yyy
Set the gateway information for an external print server.
yyy.yyy.yyy.yyy
Set the printer to automatically switch to PCL emulation when a print job received through a serial port requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job received through a serial port requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.
![Page 105 of the Lexmark MS710 user manual — Parallel [x] menu](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-105.webp?w=400)
Understanding printer menus 105
Set the size of the parallel input buffer.
Disabled Auto 3K to [maximum size allowed]
Temporarily store print jobs on the printer hard disk before printing.
Enable bidirectional communication through the parallel port.
Specify the parallel port protocol.
Determine if the printer honors printer hardware initialization requests from the computer.
Determine if the parallel port data is sampled on the leading or trailing edge of a strobe.
![Page 106 of the Lexmark MS710 user manual — Serial [x] menu](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-106.webp?w=400)
Understanding printer menus 106
Set the printer to process Macintosh binary PostScript print jobs.
Set the network address information for an external print server.
yyy.yyy.yyy.yyy
Set the netmask information for an external print server.
yyy.yyy.yyy.yyy
Set the gateway information for an external print server.
yyy.yyy.yyy.yyy
Set the printer to automatically switch to PCL emulation when a print job received through a serial port requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job received through a serial port requires it, regardless of the default printer language.

Understanding printer menus 107
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.
Set the size of the serial input buffer.
Disabled Auto 3K to [maximum size allowed]
Temporarily store print jobs on the printer hard disk before printing.
Select the hardware and software handshaking settings for the serial port.

Understanding printer menus 108
Determine whether the printer communicates availability to the computer.
Specify the rate at which data can be received through the serial port.
1200 2400 4800 9600 19200 38400 57600 115200 138200 172800 230400 345600
Specify the number of data bits sent in each transmission frame.
Set the parity for serial input and output data frames.
Even Odd None Ignore
Determine whether the printer uses the DSR Signal.
Primary SMTP Gateway Specify SMTP server gateway and port information.
Secondary SMTP Gateway Port

Understanding printer menus 109
5–30 Specify the amount of time in seconds before the server stops trying to send an e‑mail.
Reply Address Specify a reply address of up to 128 characters in the e-mail sent by the printer.
Set the printer to use SSL for increased security when connecting to the SMTP server.
Specify the type of user authentication required for scan to e‑mail privileges.
No authentication required Login/Plain CRAM‑MD5 Digest‑MD5 NTLM Kerberos 5
Device‑Initiated E‑mail
Specify what credentials will be used when communicating to the SMTP server.
None Use Device SMTP Credentials
Limit the number of times an invalid PIN can be entered.

Understanding printer menus 110
Limit the amount of time a confidential print job stays in the printer before it is deleted.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs needing verification.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs for printing at a later time.
Off 1 hour 4 hours 24 hours 1 week
Erase Temporary Data Files deletes only print job data on the printer hard disk that are not currently in use by the file system. All permanent data on the printer hard disk are preserved, such as downloaded fonts, macros, and held jobs.
Specify the mode for erasing temporary data files.

Understanding printer menus 111
Mark all disk space used by a previous print job. This method does not permit the file system to reuse this space until it has been cleared.
Single pass Multiple pass
Export Log Let an authorized user export the audit log.
Specify whether or not audit logs are deleted.
Specify how and whether or not audit logs are created.
Yes No Enable Remote Syslog
No Yes Remote Syslog Facility
0–23 Severity of events to log
Current Date and Time Show the current date and time settings for the printer.
Manually Set Date and Time
Enter the date and time.

Understanding printer menus 112
Select the time zone.
[list of time zones]
Set the printer to use the applicable daylight saving time (DST) start and end times associated with the printer Time Zone setting.
Enable Network Time Protocol, which synchronizes the clocks of devices on a network.
Set the language of the text that appears on the printer display.
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portuguese Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese

Understanding printer menus 113
Display the estimates of the supplies on the printer control panel, Embedded Web Server, menu settings, and device statistics reports.
Show estimates Do not show estimates
Minimize the use of energy, paper, or specialty media.
Off Energy Energy/Paper Paper
Reduce the amount of noise produced by the printer.
Instruct the printer to run the setup wizard.
Specify the default system of measurement for paper sizes.
Change the icons and buttons that appear on the printer control panel.
Change Language Search Held Jobs Held Jobs USB Drive Bookmarks Jobs by user
For each icon or button, select from the following options:
Display Do not display

Understanding printer menus 114
Set the amount of light from the bin.
Set an alarm when the printer requires user intervention.
Alarm Control Cartridge Alarm Staple Alarm Hole Punch Alarm
When activated, Alarm Control lets you set the number of times that the alarm sounds, while Cartridge Alarm lets you stop printing when a cartridge-low condition occurs.
For each alarm type, select from the following options:
Set the amount of time the printer waits after a job is printed before it goes into a reduced power state.

Understanding printer menus 115
Set the printer to operate at a low power state.
Disabled 1 hour 2 hours 3 hours 6 hours 1 day 2 days 3 days 1 week 2 weeks 1 month
Set the printer to follow the setting of “Hibernate Timeout” even when an active Ethernet connection exists.
Hibernate Timeout on Connection
Do Not Hibernate Hibernate
Set the amount of time in seconds the printer waits before returning the display to the Ready state.
Set the amount of time in seconds the printer waits to receive an end‑of‑job message before canceling the remainder of the print job.
Set the amount of time in seconds the printer waits for additional data before canceling a print job.

Understanding printer menus 116
Set the amount of time the printer waits for user intervention before it holds jobs that require unavailable resources and continues to print other jobs in the print queue.
Set the printer to restart when an error is encountered.
Reboot when idle Reboot always Reboot never Max Auto Reboots
Let the printer automatically continue printing from certain offline situations when these are not resolved within the specified time period.
Specify whether the printer reprints jammed pages.
Set the printer to check for jammed paper automatically.
Print a page that may not have printed otherwise.
Determine how the printer, while in idle state, reacts to a short press of the Sleep button.
Do nothing Sleep Hibernate

Understanding printer menus 117
Press and Hold Sleep Button
Determine how the printer, while in idle state, reacts to a long press of the Sleep button.
Do nothing Sleep Hibernate
Restore the printer settings to its factory defaults.
Do Not Restore Restore Now
Display information pertaining to the selected Custom Home Messages on the printer control panel display.
Off IP Address Hostname Contact Name Location Zero Configuration Name Custom Text 1
Export the printer configuration file to a flash drive.
1–999 Specify a default number of copies for each print job.
Set a default paper source for all print jobs.
Tray [x] MP Feeder Manual Paper
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)
Specify whether prints are on one side or on both sides of the page.
1 sided 2 sided

Understanding printer menus 118
Specify whether prints are stapled.
Specify whether prints have holes for binding.
Specify the number of holes to be made on the prints.
2 holes 3 holes 4 holes
Define the way duplexed pages are bound and printed.
Long Edge Short Edge
Specify the orientation of a multiple‑page document.
Specify that multiple‑page images be printed on one side of a paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up

Understanding printer menus 119
Print a border on each page image when using N‑Up (pages per side).
Specify the positioning of multiple‑page images when using N‑Up (pages per side).
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify if blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages
Specify the paper source for the separator sheet.
Tray [x] Manual Feeder MP Feeder
Specify if blank pages are inserted in a print job.
Do Not Print Print

Understanding printer menus 120
Set the default printer language.
PCL Emulation PS Emulation
Determine if print jobs are removed from the print queue when they require unavailable printer options or custom settings. These print jobs are stored in a separate print queue, so other jobs print normally. When the missing information or options, or both are obtained, the stored jobs print.
Set the logical and physical printable area.
Normal Fit to Page Whole Page

Understanding printer menus 121
Set the storage location for downloads.
Specify how the printer handles temporary downloads, such as fonts and macros stored in the RAM, when the printer receives a print job that requires more than the available memory.
Specify whether two‑sided (duplex) printing is set as the default for all print jobs.
1 sided 2 sided
Click File > Print, and then click Properties, Preferences, Options, or Setup. For Macintosh users:
Choose File > Print, and then adjust the settings from the Print dialog and pop‑up menus.
Define the way duplexed pages are bound and printed.
Long Edge Short Edge
1–999 Specify the default number of copies for each print job.

Understanding printer menus 122
Specify whether blank pages are inserted in a print job.
Do Not Print Print
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)
Specify whether blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages
Specify the paper source for the separator sheet.
Tray [x] MP Feeder
Print multiple‑page images on one side of a paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Specify the positioning of multiple‑page images when using Paper Saver.
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify the orientation of a multiple‑page document.

Understanding printer menus 123
Print a border when using Paper Saver.
Specify whether printed output is stapled.
Run Stapler Test Print a report that confirms that the staple finisher is functioning properly.
Specify whether holes will be created on printed outputs for the purpose of collecting the sheets in a binder or folder.
Specify the number of holes to be created on printed outputs for the purpose of collecting the sheets in a binder or folder.
2 holes 3 holes 4 holes
Offset pages at certain instances.
None Between Copies Between Jobs

Understanding printer menus 124
Specify the printed output resolution in dots per inch.
300 dpi 600 dpi 1200 dpi 1200 Image Q 2400 Image Q
Enable more pixels to print in clusters for clarity, in order to enhance images horizontally or vertically, or to enhance fonts.
Off Fonts Horizontally Vertically Both directions Isolated
1–10 Lighten or darken the printed output.
Enable a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts.
Automatically adjust the contrast enhancement applied to images.
Adjust the printed output either by lightening or darkening it. You can conserve toner by lightening the output.
‑6 to 6
0–5 Adjust the contrast of printed objects.

Understanding printer menus 125
Determine and set if the printer creates a log of the print jobs it receives.
Job Accounting Utilities Print and delete log files or export them to a flash drive.
Determine and set how often a log file is created.
Log Action at End of Frequency
Determine and set how the printer responds when the frequency threshold expires.
None E‑mail Current Log E‑mail & Delete Current Log Post Current Log Post & Delete Current Log
Disk Near Full Level
Specify the maximum size of the log file before the printer executes Disk Near Full Action.
Disk Near Full Action
Determine and set how the printer responds when the printer hard disk is nearly full.
None E‑mail Current Log E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post Current Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
Determine and set how the printer responds when disk usage reaches the maximum limit (100MB).
None E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
URL to Post Logs Determine and set where the printer posts job accounting logs.
E-mail to Send Logs Specify the e‑mail address to which the printer sends job accounting logs.

Understanding printer menus 126
Log File Prefix Specify the prefix you want for the log file name.
Delete confidential and held jobs from the printer hard disk.
Confidential Held Not Restored All
Format the flash memory.
Delete Downloads on Disk
Delete downloads from the printer hard disk, including all held jobs, buffered jobs, and parked jobs.
Delete Now Do Not Delete
Activate Hex Trace Assist in isolating the source of a print job problem.
Provide an estimate of the percentage coverage of toner on a page. The estimate is printed on a separate page at the end of each print job.

Understanding printer menus 127
Print a page containing information on errors, including XML markup errors.
Scale page content to fit the selected paper size.
Print annotations in a PDF.
Do Not Print Print
Print a page containing the PostScript error.
Lock PS Startup Mode
Disable the SysStart file.
Establish the font search order.

Understanding printer menus 128
Specify the set of fonts used by the Font Name menu.
Resident Disk Download Flash All
Identify a specific font and the option where it is stored.
Specify the symbol set for each font name.
Change the point size for scalable typographic fonts.
1.00–1008.00
Specify the font pitch for scalable monospaced fonts.
0.08–100
Specify the orientation of text and graphics on the page.

Understanding printer menus 129
Specify the number of lines that print on each page.
Set the printer to print on A4‑size paper.
198 mm 203 mm
Specify whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command.
Auto CR after LF
Specify whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command.
Auto LF after CR
Configure the printer to work with printer software or programs that use different source assignments for trays and feeders.
Off None 0–199 Assign Tray [x]
Off None 0–199 Assign Manual Paper
Off None 0–199 Assign Manual Env

Understanding printer menus 130
Display the factory default setting assigned to each tray or feeder.
MPF Default = 8 T1 Default = 1 T1 Default = 4 T1 Default = 5 T1 Default = 20 T1 Default = 21 Env Default = 6 MPaper Default = 2 MEnv Default = 3
Restore all tray and feeder assignments to the factory default settings.
Joanna MT Letter Gothic Lubalin Graph Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino StempelGaramond Taffy Times TimesNewRoman Univers Zapf Chancery NewSansMTJA NewSansMTCS NewSansMTCT NewSansMTKO
Set the default font for HTML documents.
Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text Intl CG Times Intl Courier Intl Univers

Understanding printer menus 131
1–255 pt Set the default font size for HTML documents.
1–400% Scale the default font for HTML documents.
Set the page orientation for HTML documents.
8–255 mm Set the page margin for HTML documents.
Specify whether to print backgrounds on HTML documents.
Do Not Print Print
Select the optimal paper size, scaling, and orientation.
Invert bitonal monochrome images.
Scale the image to fit the selected paper size.
Anchor Top Left Best Fit Anchor Center Fit Height/Width Fit Height Fit Width

Understanding printer menus 132
Set the image orientation.
Portrait Landscape Reverse Portrait Reverse Landscape
The Help menu consists of a series of Help pages that are stored in the printer as PDFs. They contain information about using the printer and performing printing tasks.
English, French, German, and Spanish translations are stored in the printer. Other translations are available at http://support.lexmark.com.
Print All Guides Prints all the guides
Print Quality Provides information about solving print quality issues
Printing Guide Provides information about loading paper and other specialty media
Media Guide Provides a list of the paper sizes supported in trays and feeders
Print Defects Guide Provides information about resolving print defects
Menu Map Provides a list of the printer control panel menus and settings
Information Guide Provides help in locating additional information
Connection Guide Provides information about connecting the printer locally (USB) or to a network
Moving Guide Provides instructions for safely moving the printer
Supplies Guide Provides part numbers for ordering supplies
Use To · Orientation · Menu item Description

Saving money and the environment 133
Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impact on the environment. We design with the environment in mind, engineer our packaging to reduce materials, and provide collection and recycling programs. For more information, see:
By selecting certain printer settings or tasks, you may be able to reduce your printer's impact even further. This chapter outlines the settings and tasks that may yield a greater environmental benefit.
Studies show that as much as 80% of the carbon footprint of a printer is related to paper usage. You can significantly reduce your carbon footprint by using recycled paper and the following printing suggestions, such as printing on both sides of the paper and printing multiple pages on one side of a single sheet of paper.
For more information on how you can quickly save paper and energy using one printer setting, see “Using Eco‑Mode” on page 134.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser printers. For more information on recycled papers that work well with your printer, see “Using recycled paper and other office papers” on page 71.
If your printer model supports duplex printing, then you can control whether print appears on one or two sides of the paper by selecting 2‑sided printing from the Print dialog or from the Lexmark Toolbar.
You can print up to 16 consecutive pages of a multiple‑page document onto one side of a single sheet of paper by selecting a setting from the Multipage printing (N‑Up) section of the Print dialog screen.
Before printing or making multiple copies of a document:

Saving money and the environment 134
Correctly set the paper type and size to avoid paper jams. For more information, see “Avoiding jams” on page 163.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Eco‑Mode.
3 Select a setting.
Off Use the factory default settings for all settings associated with Eco‑Mode.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy and Paper modes.
Plain Paper Enable the automatic two‑sided (duplex) printing feature.
4 Click Submit.
Enable Quiet mode to reduce the printer noise.
1 From the printer control panel, navigate to:
> Settings > > Settings > > General Settings > > Quiet Mode >
2 Select a setting.
Use To

Saving money and the environment 135
On Reduce printer noise.
Off Use factory default settings.
3 Press .
To save energy, decrease the number of minutes before the printer enters Sleep mode. Select from 1 to 120. The factory default setting is 30 minutes.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Navigate to:
Settings > General Settings > Timeouts
3 In the Sleep Mode field, enter the number of minutes you want the printer to wait before it enters Sleep mode.
4 Click Submit.
1 From the printer control panel, navigate to:
> Settings > > Settings > > General Settings > > Timeouts > > Sleep Mode >
2 In the Sleep Mode field, select the number of minutes you want the printer to wait before it enters Sleep mode.
3 Press .
Use To

Saving money and the environment 136
Hibernate is an ultra‑low‑power operating mode. When operating in Hibernate mode, all other systems and devices are powered down safely.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Sleep Button Settings.
3 From the “Press Sleep Button” or “Press and Hold Sleep Button” drop‑down menu, select Hibernate.
4 Click Submit.
1 From the printer control panel, navigate to:
> Settings > > Settings > > General Settings >
2 Press the arrow buttons until Press Sleep Button or Press and Hold Sleep Button appears, and
then press .
3 Press the arrow buttons until Hibernate appears, and then press .
To save energy, or if you have trouble reading the display, adjust its brightness settings.
1 Open a Web browser, and then type the printer IP address in the address field.

Saving money and the environment 137
2 Click Settings > General Settings.
3 In the Screen Brightness field, enter the brightness percentage you want for the display.
4 Click Submit.
Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information, see:
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country or region from the list.
3 Follow the instructions on the computer screen.
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark will recycle the box.
Lexmark Cartridge Collection Program diverts millions of Lexmark cartridges from landfills annually by making it both easy and free for Lexmark customers to return used cartridges to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. Boxes used to return the cartridges are also recycled.

Saving money and the environment 138
To return Lexmark cartridges for reuse or recycling, follow the instructions that came with your printer or cartridge and use the prepaid shipping label. You can also do the following:
1 Go to www.lexmark.com/recycle.
2 From the Toner Cartridges section, select your country or region.
3 Follow the instructions on the computer screen.

Securing the printer 139
Using the security lock feature
The printer is equipped with a security lock feature. When a lock compatible with most laptop computers is attached, the printer is locked. When locked, the controller board shield and the controller board cannot be removed. Attach a security lock to the printer in the location shown.


Your printer contains various types of memory that can store device and network settings, and user data.
Type of memory Description
Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print jobs.
Non-volatile memory Your printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store the operating system, device settings, network information, bookmark settings, and embedded solutions.
Hard disk memory Some printers have a hard disk drive installed. The printer hard disk is designed for device-specific functionality. This lets the device retain buffered user data from complex print jobs, as well as form data, and font data.
Erase the content of any installed printer memory in the following circumstances:

Securing the printer 140
In high‑security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer hard disk cannot be accessed when the printer—or its hard disk—is removed from your premises.
The volatile memory (RAM) installed in your printer requires a power source to retain information. To erase the buffered data, turn off the printer.
Erase individual settings, device and network settings, security settings, and embedded solutions by following these steps:
1 Turn off the printer.
2 Hold down 2 and 6 on the keypad while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
3 Press the up or down arrow button until Wipe All Settings appears.
The printer will restart several times during this process.
4 Navigate to:
Back > Exit Config Menu
The printer will perform a power‑on reset, and then return to normal operating mode.

Securing the printer 141
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
4 Press the up or down arrow button until Yes appears, and then proceed with disk wiping.
5 Navigate to:
Back > Exit Config Menu
The printer will perform a power‑on reset, and then return to normal operating mode.
Enable hard disk encryption to prevent loss of sensitive data in the event the printer or its hard disk is stolen.
1 Open a Web browser, and then type the printer IP address in the address field.

Securing the printer 142
2 Click Settings > Security > Disk Encryption.
3 From the Disk Encryption menu, select Enable.
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
3 Navigate to:
Disk Encryption > Enable
4 Select Yes to proceed with disk wiping.
5 Navigate to:
Back > Exit Config Menu
The printer will perform a power‑on reset, and then return to normal operating mode.
In high-security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer cannot be accessed by unauthorized persons. For more information, visit the Lexmark security Web page.
You can also see the Embedded Web Server — Security: Administrator’s Guide for additional information:
1 Go to www.lexmark.com, and then navigate to Support & Downloads > select your printer.
2 Click the Manuals tab, and then select Embedded Web Server — Security: Administrator’s Guide.

Maintaining the printer 143
Periodically, certain tasks are required to maintain optimum performance of your printer.
1 Make sure that the printer is turned off and unplugged from the electrical outlet.
2 Remove paper from the standard bin and multipurpose feeder.
3 Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.
4 Dampen a clean, lint-free cloth with water, and use it to wipe the outside of the printer.
5 Make sure all areas of the printer are dry before sending a new print job.
1 Pull out the hole punch box.


Maintaining the printer 144
2 Empty the container.

3 Insert the emptied hole punch box back into the finisher until it clicks into place.


A message appears on the printer display when a replacement supply item is needed or when maintenance is required.
From the printer control panel, navigate to:
> Status/Supplies > View Supplies >

Maintaining the printer 145
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Device Status > More Details.
You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Supply Notifications.
3 From the drop‑down menu for each supply, select one of the following notification options:
Off The normal printer behavior for all supplies occurs.
E‑mail Only The printer generates an e-mail when the supply condition is reached. The status of the supply will appear on the menus page and status page.
Continuable Stop1 The printer stops processing jobs when the supply condition is reached, and the user needs to press a button to continue printing.
1 The printer generates an e-mail about the status of the supply when supply notification is enabled.
2 The printer stops when some supplies become empty to prevent damage.
Notification Description

Maintaining the printer 146
Non Continuable Stop1,2 The printer stops when the supply condition is reached. The supply must be replaced to continue printing.
1 The printer generates an e-mail about the status of the supply when supply notification is enabled.
2 The printer stops when some supplies become empty to prevent damage.
4 Click Submit.
To order parts and supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, visit the Lexmark Web site at www.lexmark.com or contact the place where you purchased the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. Use of third-party supplies or parts can affect warranty coverage. Damage caused by the use of third-party supplies or parts is not covered by the warranty. All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.
The estimated number of remaining pages is based on the recent printing history of the printer. Its accuracy may vary significantly and is dependent on many factors, such as actual document content, print quality settings, and other printer settings.
The accuracy of the estimated number of remaining pages may decrease when the actual printing consumption is different from the historical printing consumption. Consider the variable level of accuracy before purchasing or replacing supplies based on the estimate. Until an adequate print history is obtained on the printer, initial estimates assume future supplies consumption based on the International Organization for Standardization* test methods and page content.
* Average continuous black declared cartridge yield in accordance with ISO/IEC 19752.
Notification Description

Maintaining the printer 147

For the European Union, European Economic Area , and Switzerland
For the Asia Pacific Region (includes Australia and New Zealand)
For Africa, Middle East, Central Eastern Europe, and Commonwealth of Independent States
* This toner cartridge is supported only in the MS711 printer model.
For more information on countries located in a region, visit www.lexmark.com/regions.
1 This cartridge is supported only in the MS710 printer model.
2 This cartridge is supported only in the MS711 printer model.
Extremely low print coverage for extended periods of time may cause imaging unit parts to fail prior to exhaustion of toner.
For more information on replacing the imaging unit, see the instruction sheet that came with the supply.
Part name Lexmark Return Program Regular
Imaging unit 520Z 520ZA
Part name Part number
Staple cartridges 25A0013

Maintaining the printer 148
Part name Part number
Oil wiper in bag 40x8579
Wax wiper in bag 40X8581
To identify the supported fuser type, view the label on the fuser. Do either of the following:
MS710 Series Return Program fuser maintenance kit type 11, 110–120V 40X8530
MS710 Series Return Program fuser maintenance kit type 13, 220–240V 40X8531
MS710 Series Return Program fuser maintenance kit type 15, 100V 40X8532
MS710 Series regular fuser maintenance kit type 17, 110–120V 40X8533
MS710 Series regular fuser maintenance kit type 19, 220–240V 40X8534
MS710 Series regular fuser maintenance kit type 21, 100V 40X8535
MS710 Series roller kit 40X7706
Type Part number · Type Part number · Part number

Maintaining the printer 149
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:
1 Lift the front cover, and then pull down the multipurpose feeder door.


Maintaining the printer 150
2 Pull the cartridge out of the printer using the handle.

3 Unpack the new toner cartridge, then remove the packing material, and then shake the cartridge to redistribute the toner.

4 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.


Maintaining the printer 151
5 Close the multipurpose feeder door and the front cover.
1 Lift the front cover, and then pull down the multipurpose feeder door.

Maintaining the printer 152
2 Pull out the toner cartridge from the printer using the handle.
3 Lift the green handle, and then pull out the imaging unit from the printer.


4 Unpack the new imaging unit, and then shake it.

5 Remove all packing material from the imaging unit.

Maintaining the printer 153

6 Insert the imaging unit into the printer by aligning the arrows on the side rails of the imaging unit with the arrows on the side rails inside the printer.

7 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.

Maintaining the printer 154
8 Close the multipurpose feeder door and the front cover.
1 Open the stapler door.

2 Pull down the latch of the staple cartridge holder, and then pull the holder out of the finisher.



Maintaining the printer 155
3 Squeeze both sides of the empty staple case with your fingers, and then remove the staple case from the cartridge.

4 Insert the front side of the new staple case into the staple cartridge, and then push the rear side into the cartridge.

5 Push the staple cartridge into the finisher until it clicks into place.
6 Close the stapler door.
1 Turn off the printer.
2 Squeeze the fuser wiper cover tab, and then lift to remove the cover assembly.

Maintaining the printer 156



3 Install the new cover assembly into the printer.

4 Turn on the printer.
1 Turn off the printer.
2 Squeeze the fuser wiper cover tab, and then lift to remove the cover assembly.

Maintaining the printer 157
3 Press the green portion of the fuser wiper against the fuser wiper cover, and then unhook the right side of the wiper from the cover frame to remove the fuser wiper.


4 Insert the left side of the new fuser wiper tab through the slot on the left side of the cover frame.


5 Hook the right side of the fuser wiper on the right side of the cover frame.



Maintaining the printer 158
6 Install the cover assembly into the printer.
7 Turn on the printer.
– Make sure to remove the topmost finisher first. – To remove the finisher, hold the finisher on both sides, and then lift the latches to unlock the finisher.

Maintaining the printer 159





Maintaining the printer 160
The printer and its hardware options can be safely moved to another location by following these precautions:
When shipping the printer, use the original packaging or call the place of purchase for a relocation kit.

Managing the printer 161
Finding advanced networking and administrator information
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server — Security: Administrator's Guide on the Lexmark support Web site at http://support.lexmark.com.
The remote control panel on your computer screen lets you interact with the printer control panel, even when you are not physically near the network printer. From your computer screen, you can view the printer status and do print- related tasks you might normally do while standing at the network printer.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Press Enter to open the Web page of your printer.
3 Click Applications.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings tab > Security > Confidential Print Setup.
4 Save the modified settings.

Managing the printer 162
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click the Copy Printer Settings.
3 To change the language, select a language from the drop-down menu, and then click Click here to submit language.
4 Click Printer Settings.
5 Type the IP addresses of the source and target printers in their appropriate fields.
6 Click Copy Printer Settings.
If you want to keep a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings. For more information, see “Printing a menu settings page” on page 47.
If you want a more comprehensive method of restoring the printer factory default settings, then perform the Wipe All Settings option. For more information, see “Erasing non‑volatile memory” on page 140.
From the printer control panel, navigate to:
> Settings > > Settings > > General Settings > > Factory Defaults > > Restore Now >

Carefully select paper and specialty media, and then load them properly to avoid most jams. For more information, see “Avoiding jams” on page 163. If jams occur, then follow the steps outlined in this chapter.

Clearing jams 163



– If the bin extender is shorter than the size of the paper you are printing on, then the paper causes a jam in
the mailbox bin. For example, if you are printing on a legal-size paper and the bin extender is set to letter- size, then a jam occurs. – If the bin extender is longer than the size of the paper you are printing on, then the edges become uneven
and the paper is not stacked properly. For example, if you are printing on a letter-size paper and the bin extender is set to legal-size, then the paper does not stack properly.
Clearing jams 164



When a jam occurs, a message indicating the jam location and information to clear the jam appears on the printer display. Open the doors, covers, and trays indicated on the display to remove the jam.
Clearing jams 165


3 4 5 6


Jam location Printer message What to do
1 Staple finisher [x]‑page jam, remove paper, open stapler door. Leave paper in bin. [455– 457]
Remove paper from the stapler bin, open the stapler door, then remove the staple cartridge, and then remove the jammed staples.
2 Standard bin [x]‑page jam, remove standard bin jam. [203]
Remove jammed paper from the standard bin.
3 Inside the printer [x]‑page jam, lift front cover to remove cartridge. [200–201]
Open the front cover and the multipurpose feeder, then remove the toner cartridge and the imaging unit, and then remove the jammed paper.
4 Multipurpose feeder [x]‑page jam, clear manual
Remove all paper from the multipurpose feeder, and then remove the jammed paper.
feeder. [250]
5 Duplex area [x]‑page jam, remove tray 1 to clear duplex. [235–239]
Pull out tray 1 completely, then push down the front duplex flap, and then remove the jammed paper.
6 Trays [x]‑page jam, open tray [x]. [24x] Pull out the indicated tray, and then remove the jammed paper.
7 Output expander [x]‑page jam, remove paper, open expander rear door. Leave paper in bin. [41y.xx]
Open the rear door of the output expander, and then remove the jammed paper.
8 Upper rear door [x]‑page jam, open upper rear door. [202]
Open the rear door of the printer, and then remove the jammed paper.
Clearing jams 166
![Page 167 of the Lexmark MS710 user manual — [x] ‑ page jam, lift front cover to remove cartridge [200–201]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-167.webp?w=400)
Jam location Printer message What to do
9 Upper door and rear duplex area
[x]‑page jam, open upper and lower rear door. [231–234]
Open the rear door of the printer and the rear duplex area, and then remove the jammed paper.
10 Mailbox [x]‑page jam, remove paper, open mailbox rear door. Leave paper in bin. [43y.xx]
Open the rear door of the mailbox, and then remove the jammed paper.
[x]‑page jam, remove paper, open finisher rear door. Leave paper in bin. [451]
11 Staple finisher rear door
Open the rear door of the staple finisher, and then remove the jammed paper.
1 Lift the front cover, and then pull down the multipurpose feeder door.
Clearing jams 167
![Page 168 of the Lexmark MS710 user manual — [x]-page jam, lift front cover to remove cartridge [200–201]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-168.webp?w=400)
2 Lift the green handle, and then pull the toner cartridge out of the printer.
3 Place the cartridge aside.
4 Lift the green handle, and then pull the imaging unit out of the printer.
![Lexmark MS710 — [x]-page jam, lift front cover to remove cartridge [200–201] diagram (page 168)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-116.webp)
![Lexmark MS710 — [x]-page jam, lift front cover to remove cartridge [200–201] diagram (page 168)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-117.webp)
5 Place the imaging unit aside on a flat, smooth surface.
6 Pull the jammed paper gently to the right, and then remove it from the printer.
Clearing jams 168
![Page 169 of the Lexmark MS710 user manual — [x]-page jam, lift front cover to remove cartridge [200–201]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-169.webp?w=400)
![Lexmark MS710 — [x]-page jam, lift front cover to remove cartridge [200–201] diagram (page 169)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-118.webp)
7 Install the imaging unit.
8 Insert the cartridge into the printer, and then push the green handle back into place.
Clearing jams 169
![Page 170 of the Lexmark MS710 user manual — [x] ‑ page jam, open upper rear door [202]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-170.webp?w=400)
9 Close the multipurpose feeder door and the front cover.
10 To clear the message and continue printing, select Next > > Clear the jam, press OK > .
1 Pull down the rear door.
![Lexmark MS710 — [x] ‑ page jam, open upper rear door [202] diagram (page 170)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-119.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 170
![Page 171 of the Lexmark MS710 user manual — [x] ‑ page jam, open upper and lower rear door [231–234]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-171.webp?w=400)
3 Close the rear door.
4 To clear the message and continue printing, select Next > > Clear the jam, press OK > .
1 Pull down the rear door.
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 171
![Page 172 of the Lexmark MS710 user manual — [x]-page jam, open upper and lower rear door [231–234]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-172.webp?w=400)
3 Close the rear door.
4 Push the back of the standard tray.
![Lexmark MS710 — [x]-page jam, open upper and lower rear door [231–234] diagram (page 172)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-120.webp)
5 Press down the rear duplex flap, then firmly grasp the jammed paper, and then gently pull the paper out.
Clearing jams 172
![Page 173 of the Lexmark MS710 user manual — [x] ‑ page jam, remove standard bin jam [203]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-173.webp?w=400)
![Lexmark MS710 — [x]-page jam, remove standard bin jam [203] diagram (page 173)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-121.webp)
![Lexmark MS710 — [x]-page jam, remove standard bin jam [203] diagram (page 173)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-122.webp)
6 Insert the standard tray.
7 To clear the message and continue printing, select Next > > Clear the jam, press OK > .
1 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark MS710 — [x] ‑ page jam, remove standard bin jam [203] diagram (page 173)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-123.webp)
2 To clear the message and continue printing, select Next > > Clear the jam, press OK > .
Clearing jams 173
![Page 174 of the Lexmark MS710 user manual — [x] ‑ page jam, remove tray 1 to clear duplex [235–239]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-174.webp?w=400)
1 Lift the tray slightly, and then pull out it out completely.
![Lexmark MS710 — [x] ‑ page jam, remove tray 1 to clear duplex [235–239] diagram (page 174)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-124.webp)
![Lexmark MS710 — [x] ‑ page jam, remove tray 1 to clear duplex [235–239] diagram (page 174)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-125.webp)
2 Push down the front duplex flap, then firmly grasp the jammed paper, and then gently pull the paper to the right and out of the printer.
![Lexmark MS710 — [x] ‑ page jam, remove tray 1 to clear duplex [235–239] diagram (page 174)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-126.webp)
3 Insert the tray.
4 To clear the message and continue printing, select Next > > Clear the jam, press OK > .
Clearing jams 174
![Page 175 of the Lexmark MS710 user manual — [x] ‑ page jam, open tray [x] [24x]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-175.webp?w=400)
1 Check which tray is indicated on the printer display.
2 Lift the tray slightly, and then pull it out completely.
![Lexmark MS710 — [x] ‑ page jam, open tray [x] [24x] diagram (page 175)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-127.webp)
3 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark MS710 — [x] ‑ page jam, open tray [x] [24x] diagram (page 175)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-128.webp)
4 Insert the tray.
5 To clear the message and continue printing, select Next > > Clear the jam, press OK > .
Clearing jams 175
![Page 176 of the Lexmark MS710 user manual — [x] ‑ page jam, clear manual feeder [250]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-176.webp?w=400)
1 From the multipurpose feeder, firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark MS710 — [x] ‑ page jam, clear manual feeder [250] diagram (page 176)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-129.webp)
2 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.
3 Reload paper into the multipurpose feeder.
4 Slide the paper guide until it lightly rests against the edge of the paper.
![Lexmark MS710 — [x] ‑ page jam, clear manual feeder [250] diagram (page 176)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-130.webp)
![Lexmark MS710 — [x] ‑ page jam, clear manual feeder [250] diagram (page 176)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-131.webp)
5 To clear the message and continue printing, select Next > > Clear the jam, press OK > .
Clearing jams 176
![Page 177 of the Lexmark MS710 user manual — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-177.webp?w=400)
[x]‑page jam, remove paper, open stapler door. Leave paper in bin. [455–457]
1 From the stapler bin, firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark MS710 — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457] diagram (page 177)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-132.webp)
2 Open the stapler door.
3 Pull down the latch of the staple cartridge holder, and then pull the holder out of the printer.
Clearing jams 177
![Page 178 of the Lexmark MS710 user manual — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-178.webp?w=400)
4 Use the metal tab to lift the staple guard, and then remove any loose staples.
![Lexmark MS710 — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457] diagram (page 178)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-133.webp)
5 Press down the staple guard until it clicks into place.
![Lexmark MS710 — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457] diagram (page 178)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-134.webp)
Clearing jams 178
![Page 179 of the Lexmark MS710 user manual — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-179.webp?w=400)
6 Slide the staples toward the metal bracket.
![Lexmark MS710 — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457] diagram (page 179)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-135.webp)
![Lexmark MS710 — [x]-page jam, remove paper, open stapler door. Leave paper in bin. [455–457] diagram (page 179)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-136.webp)
7 Push the cartridge holder firmly back into the stapler unit until the cartridge holder clicks into place.
8 Close the stapler door.
9 To clear the message and continue printing, select Next > > Clear the jam, press OK > .
Clearing jams 179
![Page 180 of the Lexmark MS710 user manual — [x]-page jam, remove paper, open finisher rear door. Leave paper in bin. [451]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-180.webp?w=400)
[x]‑page jam, remove paper, open finisher rear door. Leave paper in bin. [451]
1 Open the rear staple finisher door.
![Lexmark MS710 — [x]-page jam, remove paper, open finisher rear door. Leave paper in bin. [451] diagram (page 180)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-137.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
3 Close the staple finisher door.
4 To clear the message and continue printing, select Next > > Clear the jam, press OK > .
Clearing jams 180
![Page 181 of the Lexmark MS710 user manual — [x]-page jam, remove paper, open expander rear door. Leave paper in bin. [41y.xx]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-181.webp?w=400)
[x]‑page jam, remove paper, open expander rear door. Leave paper in bin. [41y.xx]
1 Open the output expander rear door.
![Lexmark MS710 — [x]-page jam, remove paper, open expander rear door. Leave paper in bin. [41y.xx] diagram (page 181)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-138.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
3 Close the output expander rear door.
4 To clear the message and continue printing, select Next > > Clear the jam, press OK > .
Clearing jams 181
![Page 182 of the Lexmark MS710 user manual — [x]-page jam, remove paper, open mailbox rear door. Leave paper in bin. [43y.xx]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-182.webp?w=400)
[x]‑page jam, remove paper, open mailbox rear door. Leave paper in bin. [43y.xx]
1 Open the mailbox rear door.
![Lexmark MS710 — [x]-page jam, remove paper, open mailbox rear door. Leave paper in bin. [43y.xx] diagram (page 182)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-139.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
3 Close the mailbox rear door.
Clearing jams 182
![Page 183 of the Lexmark MS710 user manual — [x]-page jam, remove paper, open mailbox rear door. Leave paper in bin. [43y.xx]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-183.webp?w=400)
4 If the jam is in the mailbox bin, then firmly grasp the jammed paper, and then gently pull it out.
![Lexmark MS710 — [x]-page jam, remove paper, open mailbox rear door. Leave paper in bin. [43y.xx] diagram (page 183)](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/rimg-140.webp)
5 To clear the message and continue printing, select Next > > Clear the jam, press OK > .
Clearing jams 183
![Page 184 of the Lexmark MS710 user manual — Change [paper source] to [custom string] load [orientation]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-184.webp?w=400)
Understanding the printer messages
1 Check if both the toner cartridge and imaging unit are MICR (Magnetic Ink Character Recognition) or non-MICR supplies.
2 Change the toner cartridge or imaging unit so that both are MICR or non‑MICR supplies.
You may need to order a toner cartridge. If necessary, press on the printer control panel to clear the message and continue printing.
If necessary, press on the printer control panel to clear the message and continue printing.
You may need to replace a toner cartridge very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, press on the printer control panel to clear the message and continue printing.
Try one or more of the following:
Troubleshooting 184
![Page 185 of the Lexmark MS710 user manual — Check tray [x] connection](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-185.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
If the error occurs a second time, then:
1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Remove the specified tray. 4 Reattach the tray. 5 Connect the power cord to a properly grounded electrical outlet. 6 Turn the printer back on.
If the error occurs again, then:
1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Remove the tray. 4 Contact customer support.
Troubleshooting 185
![Page 186 of the Lexmark MS710 user manual — Defective flash detected [51]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-186.webp?w=400)
The toner cartridge is missing or not installed properly. Insert the cartridge, and then close all doors and covers.
Close the rear door of the finisher.
Close the rear door of the printer.
Try one or more of the following:
Held jobs are unavailable because of any of the following possible changes in the printer:
From the printer control panel, press to clear the message and continue printing.
Try one or more of the following:
Troubleshooting 186
![Page 187 of the Lexmark MS710 user manual — Imaging unit nearly low [84.xy]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-187.webp?w=400)
Try one or more of the following:
From the printer control panel, select Format disk to format the printer hard disk and clear the message.
Disk near full. Securely clearing disk space.
Try one or more of the following:
1 Empty the hole punch box.
For more information, see the “Cleaning the printer” section of the User’s Guide.
2 Reinsert the hole punch box into the finisher, and then press on the printer control panel to clear the message.
Error reading USB drive. Remove USB.
An unsupported USB device is inserted. Remove the USB device, and then insert a supported one.
Error reading USB hub. Remove hub.
An unsupported USB hub has been inserted. Remove the USB hub, and then install a supported one.
You may need to order an imaging unit. If necessary, press on the printer control panel to clear the message and continue printing.
If necessary, press on the printer control panel to clear the message and continue printing.
Troubleshooting 187

You may need to replace the imaging unit very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, press on the printer control panel to clear the message and continue printing.
Do either of the following:
Do either of the following:
Try one or more of the following:
Insert the hole punch box into the finisher, and then press on the printer control panel to clear the message.
Do either of the following:
Troubleshooting 188
![Page 189 of the Lexmark MS710 user manual — Insufficient memory, some Held Jobs were deleted [37]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-189.webp?w=400)
Insert the indicated tray into the printer.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
> Settings > > Settings > >Print Settings > > Utilities Menu > > Format Flash > > Yes >
From the printer control panel, press to clear the message.
Troubleshooting 189
![Page 190 of the Lexmark MS710 user manual — Load [paper source] with [custom string] [orientation]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-190.webp?w=400)
Do either of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
For more information, see the “Replacing supplies” section of the User’s Guide.
Try one or more of the following:
Troubleshooting 190
![Page 191 of the Lexmark MS710 user manual — Load Manual Feeder with [custom string] [orientation]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-191.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 191
![Page 192 of the Lexmark MS710 user manual — Maintenance kit nearly low [80.xy]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-192.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
You may need to order a maintenance kit. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
If necessary, press on the printer control panel to clear the message and continue printing.
For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
If necessary, press on the printer control panel to clear the message and continue printing.
Troubleshooting 192
![Page 193 of the Lexmark MS710 user manual — Non ‑ Lexmark [supply type], see User’s Guide [33.xy]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-193.webp?w=400)
You may need to replace the maintenance kit very soon. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
If necessary, press on the printer control panel to clear the message and continue printing.
Try one or more of the following:
Try one or more of the following:
The printer has detected a non‑Lexmark supply or part installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components.
All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or associated components.
To accept any and all of these risks and to proceed with the use of non-genuine supplies or parts in your printer,
press and on the printer control panel simultaneously for 15 seconds to clear the message and continue printing.
If you do not wish to accept these risks, then remove the third‑party supply or part from your printer, and then install a genuine Lexmark supply or part.
Troubleshooting 193
![Page 194 of the Lexmark MS710 user manual — Reattach bin [x]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-194.webp?w=400)
Try one or more of the following:
From the printer control panel, navigate to:
> Settings > > Settings > > Print Settings > > Utilities Menu > > Format Flash > > Yes >
Try one or more of the following:
Printer had to restart. Last job may be incomplete.
From the printer control panel, select Continue to clear the message and continue printing.
For more information, visit http://support.lexmark.com or contact customer support.
Do either of the following:
The printer discards any data received through the parallel port. • Select Reset active bin to reset the bin for a linked set of bins.
Try one or more of the following:
Troubleshooting 194
![Page 195 of the Lexmark MS710 user manual — Reinstall missing or unresponsive cartridge [31.xy]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-195.webp?w=400)
5 Connect the power cord to a properly grounded electrical outlet. 6 Turn the printer back on. • Remove the specified bin: 1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Remove the specified bin. 4 Contact customer support.
Try one or more of the following:
From the printer control panel, press to clear the message and print without using the specified bins.
Try one or more of the following:
For information on installing the cartridge, see the “Replacing supplies” section of the User’s Guide. • If the toner cartridge is installed, then remove the unresponsive toner cartridge, and then reinstall it.
Troubleshooting 195
![Page 196 of the Lexmark MS710 user manual — Remove paper from [linked set bin name]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-196.webp?w=400)
Try one or more of the following:
For more information on installing the fuser, see the instruction sheet that came with the part.
Try one or more of the following:
For information on installing the imaging unit, see the “Replacing supplies” section of the User’s Guide. • If the imaging unit is installed, then remove the unresponsive imaging unit, and then reinstall it.
Remove and replace the defective printer hard disk.
1 Remove any remaining packaging material from the specified location.
2 From the printer control panel, press to clear the message and continue printing.
Remove paper from all bins to clear the message and continue printing.
Remove paper from the specified bin to clear the message and continue printing.
Remove paper from the specified bin to clear the message and continue printing.
If removing the paper does not clear the message, then select Continue on the printer control panel.
Troubleshooting 196
![Page 197 of the Lexmark MS710 user manual — Replace maintenance kit, 0 estimated pages remain [80.xy]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-197.webp?w=400)
Remove the paper stack from the standard bin.
Replace the toner cartridge to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Install a toner cartridge that matches the region number of the printer. x indicates the value of the printer region. y indicates the value of the cartridge region. x and y can have the following values:
1 United States, Canada
2 European Economic Area (EEA), Switzerland
3 Asia Pacific, Australia, New Zealand
5 Africa, Middle East, rest of Europe
Replace the imaging unit to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
The printer is scheduled for maintenance. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact your service representative, and then report the message.
![Page 198 of the Lexmark MS710 user manual — Serial port [x] disabled [56]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-198.webp?w=400)
1 Replace the roller kit. For more information, see the instruction sheet that came with the part.
2 Press to clear the message and continue printing.
Remove the toner cartridge, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Remove the fuser, and then install a supported one. For more information, see the instruction sheet that came with the part.
Remove the imaging unit, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
1 Replace the fuser wiper. For more information, see the instruction sheet that came with the part.
2 Press to clear the message and continue printing.
Do either of the following:
Try one or more of the following:
The printer discards any data received through the specified serial port. • Select Reset active bin to reset the active bin for a linked set of bins.
Troubleshooting 198
![Page 199 of the Lexmark MS710 user manual — Too many bins attached [58]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-199.webp?w=400)
From the printer control panel, select Continue to clear the message and continue printing.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
are needed to continue processing the current job, and then press to clear the message and continue printing. 1 Order the missing supply immediately. 2 Install the supply. For more information, see the instruction sheet that came with the supply. • Cancel the print job, then install the missing supply, and then resend the print job.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra bins.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Troubleshooting 199

1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra printer hard disks.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra flash memory.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra trays.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
The paper size in the specified tray is unsupported. Replace it with a supported paper size.
Try one or more of the following:
An unsupported disk has been inserted. Remove the unsupported disk, and then install a supported one.
Troubleshooting 200

1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the unsupported option card from the printer controller board, and then replace it with a supported card.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Try one or more of the following:
Step 1 Make sure the printer is turned on.
Go to step 2. Turn on the printer.
Is the printer turned on?
Press the Sleep button to wake the printer from Sleep mode or Hibernate mode.
Go to step 3.
Check if the printer is in Sleep mode or Hibernate mode.
Is the printer in Sleep mode or Hibernate mode?
Go to step 4. Plug one end of the power cord into the printer and the other to a properly grounded electrical outlet.
Check if one end of the power cord is plugged into the printer and the other to a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
![Page 202 of the Lexmark MS710 user manual — Unsupported option in slot [x] [55]](/cdn/reader/73/7354103e167536687ff4f5791a7b501a70458c2d79a3dd91c60a9334654c892e/images/page-202.webp?w=400)
Unplug the other electrical equipment, and then turn on the printer. If the printer does not work, then reconnect the other electrical equipment.
Go to step 5.
Check other electrical equipment plugged into the electrical outlet.
Does other electrical equipment work?
Step 5 Check if the cables connecting the printer and the computer are inserted in the correct ports.
Go to step 6. Make sure to match the following:
Are the cables inserted in the correct ports?
Turn on the switch or reset the breaker.
Go to step 7.
Make sure the electrical outlet is not turned off by a switch or breaker.
Is the electrical outlet turned off by a switch or breaker?
Connect the printer power cord directly to a properly grounded electrical outlet.
Go to step 8.
Check if the printer is plugged into any surge protectors, uninterruptible power supplies, or extension cords.
Is the printer plugged into any surge protectors, uninterruptible power supplies, or extension cords?
Go to step 9. Connect the printer cable securely to the printer and the computer, print server, option, or other network device.
Check if one end of the printer cable is plugged into a port on the printer and the other to the computer, print server, option, or other network device.
Is the printer cable securely attached to the printer and the computer, print server, option, or other network device?
Go to step 10. Turn off the printer, remove all packing materials, then reinstall the hardware options, and then turn on the printer.
Make sure to install all hardware options properly and remove any packing material.
Are all hardware options properly installed and all packing material removed?
Go to step 11. Use correct printer driver settings.
Check if you have selected the correct port settings in the printer driver.
Are the port settings correct?

Go to step 12. Install the correct printer driver.
Check the installed printer driver.
Is the correct printer driver installed?
The problem is solved. Contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Is the printer working?
The problem is solved. Go to step 2.
Press the Sleep button on the printer control panel.
Does Ready appear on the printer display?
The problem is solved. Turn off the printer, and then contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Do Please wait and Ready appear on the printer display?

The problem is solved. Go to step 2.
a Pull out the tray, and then do one or more of the following:
Does the tray operate properly?
The problem is solved. Go to step 3.
Turn off the printer, then wait about 10 seconds, and then turn it back on.
Does the tray operate properly?
Step 3 Print a menu settings page, and then check if the tray is listed in the Installed Features list.
Go to step 4. For more information, see the setup sheet that came with the 2100-sheet tray.
Is the tray listed in the menu settings page?
Step 4 Check if the tray is available in the printer driver.
Go to step 5. Manually add the tray in the printer driver.
Is the tray available in the printer driver?
Step 5 Check if the tray is selected.
The problem is solved. Contact customer support.
From the application you are using, select the tray. If you are using Mac OS X version 9, then make sure the printer is set up in Chooser.
Does the tray operate properly?

The problem is solved. Go to step 2.
Turn off the printer, then wait for about 10 seconds, and then turn on the printer.
Does the internal option operate correctly?
Go to step 3. Connect the internal option to the controller board.
Check if the internal option is properly installed in the controller board.
a Turn off the printer using the power switch, and then unplug the power
cord from the electrical outlet. b Make sure the internal option is installed in the appropriate connector
in the controller board. c Connect the power cord to the printer, then to a properly grounded
electrical outlet, and then turn on the printer.
Is the internal option properly installed in the controller board?
Go to step 4. Reinstall the internal option.
Print a menu settings page, and then check to see if the internal option is listed in the Installed Features list.
Is the internal option listed in the menu settings page?
The problem is solved. Contact customer support.
a Check if the internal option is selected.
It may be necessary to manually add the internal option in the printer driver to make it available for print jobs. For more information, see “Updating available options in the printer driver” on page 38. b Resend the print job.
Does the internal option operate correctly?
Go to step 2. Check if the internal print server is supported by the printer.
Reinstall the internal print server.
a Remove, and then install the internal print server. For more
information, see “Installing an Internal Solutions Port” on page 19. b Print a menu settings page, and then check if the internal print server
is listed in the Installed Features list.
Is the internal print server listed in the Installed Features list?

The problem is solved. Contact customer support.
Check the cable and the internal print server connection.
Use the correct cable, and then check if it is securely connected to the internal print server.
Does the internal print server operate correctly?
The problem is solved. Go to step 2.
a Pull out the tray, and then do one or more of the following:
Is the tray working?
The problem is solved. Go to step 3.
a Turn off the printer, then wait about 10 seconds, and then turn the
printer back on. b Resend the print job.
Is the tray working?
Go to step 4. Reinstall the tray. For more information, see the setup documentation that came with the tray.
Check if the tray is installed and recognized by the printer.
Print a menu settings page, and then check if the tray is listed in the Installed Features list.
Is the tray listed in the menu settings page?
The problem is solved. Contact customer support.
Check if the tray is available in the printer driver.
Is the tray available in the printer driver?

Go to step 2. Check if you have a supported ISP.
Make sure the Internal Solutions Port (ISP) is installed.
a Install the ISP. For more information, see “Installing an Internal
Solutions Port” on page 19. b Print a menu settings page, and then check if the ISP is listed in the
Installed Features list.
Is the ISP listed in the Installed Features list?
The problem is solved. Contact customer support.
Check the cable and the ISP connection.
a Use the correct cable, and then make sure it is securely connected to
the ISP. b Check if the ISP solution interface cable is securely connected into the
receptacle of the controller board.
Does the Internal Solutions Port operate correctly?
Go to step 2. Check if you have a supported USB or parallel interface card.
Make sure the USB or parallel interface card is installed.
a Install the USB or parallel interface card. For more information, see
“Installing an Internal Solutions Port” on page 19. b Print a menu settings page, and then check if the USB or parallel
interface card is listed in the Installed Features list.
Is the USB or parallel interface card listed in the Installed Features list?
The problem is solved. Contact customer support.
Check the cable and the USB or parallel interface card connection.
Use the correct cable, and then make sure it is securely connected to the USB or parallel interface card.
Does the USB or parallel interface card operate correctly?

a Turn on jam recovery.
The problem is solved. Contact customer support.
1 From the printer control panel, navigate to:
Settings > General Settings > Print Recovery > Jam Recovery
2 Select On or Auto, and then press . b Resend the pages that did not print.
Were the jammed pages reprinted?
Go to step 2. The problem is solved.
a Pull out the tray, and then do one or more of the following:
If jam recovery is enabled, then the print jobs will reprint automatically.
Do paper jams still occur frequently?
Go to step 3. The problem is solved.
a Load paper from a fresh package.
Do paper jams still occur frequently?
Contact customer support.
The problem is solved.
a Review the tips on avoiding jams. For more information, see “Avoiding
jams” on page 163. b Follow the recommendations, and then resend the print job.
Do paper jams still occur frequently?

a From the printer control panel, navigate to:
Contact customer support.
The problem is solved.
Next > > Clear the jam, press OK > b Follow the instructions on the printer display.
Does the paper jam message remain?
The problem is solved. Go to step 2.
a From the printer control panel, open the Held Jobs folder, and then
verify that your print job is listed. b Resend the print job.
For more information, see “Printing confidential and other held jobs” on page 82.
Did the jobs print?
The problem is solved. Go to step 3.
Do one or more of the following:
Did the jobs print?
The problem is solved. Contact customer support.
a Increase the printer memory. Do one or more of the following:
Did the jobs print?

Go to step 2. Insert the flash drive into the front USB port.
Check if the flash drive is inserted into the front USB port.
Is the flash drive inserted into the front USB port?
Wait until the printer is ready, then view the held jobs list, and then print the documents.
Go to step 3.
Check if the indicator light on the printer control panel is blinking green.
Is the indicator light blinking green?
Go to step 4. The problem is solved.
a Check for an error message on the display. b Clear the message.
Does the error message still appear?
Go to step 5. The problem is solved.
Check if the flash drive is supported.
For more information on tested and approved USB flash drives, see “Supported flash drives and file types” on page 80.
Does the error message still appear?
Contact customer support.
The problem is solved.
Check if the USB port is disabled by the system support person.
Does the error message still appear?
Deactivate Hex Trace mode.
Go to step 2.
Make sure the printer is not in Hex Trace mode.
Is the printer in Hex Trace mode?
Contact customer support.
The problem is solved.
a From the printer control panel, select Standard Network or
Network [x], and then set SmartSwitch to On. b Resend the print job.
Do incorrect characters print?

The problem is solved. Go to step 2.
a Check if you are printing on paper that is supported by the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 3.
a From the Paper menu on the printer control panel, set the paper size
and type to match the paper loaded in the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 4.
a Depending on your operating system, open Printing Preferences or
the Print dialog, and then specify the paper type. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Contact customer support.
a Check if the trays are not linked. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 2.
a From the Finishing menu on the printer control panel, set Collate to
(1,2,3) (1,2,3). b Resend the print job.
Did the job print and collate correctly?
The problem is solved. Go to step 3.
a From the printer software, set Collate to (1,2,3) (1,2,3).
Did the job print and collate correctly?

The problem is solved. Contact customer support.
Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Did the job print and collate correctly?
Multiple‑language PDF files do not print
The problem is solved. Go to step 2.
a Check if the print options for the PDF output are set to embed all fonts. b Generate a new PDF file, and then resend the print job.
Do the files print?
The problem is solved. Contact customer support.
a Open the document you want to print in Adobe Acrobat. b Click File > Print > Advanced > Print As Image > OK > OK.
Do the files print?
The problem is solved. Go to step 2.
Change the environmental settings of the printer.
a From the printer control panel, navigate to:
Settings > General Settings b Select Eco‑Mode or Quiet Mode, and then select Off.
Did the job print?
The problem is solved. Go to step 3.
Reduce the number and size of fonts, the number and complexity of images, and the number of pages in the print job, and then resend the job
Did the job print?
The problem is solved. Go to step 4.
a Remove held jobs stored in the printer memory. b Resend the print job.
Did the job print?

The problem is solved. Go to step 5.
a Disable the Page Protect feature.
From the printer control panel, navigate to:
Settings > General Settings > Print Recovery > Page Protect > Off b Resend the print job.
Did the job print?
The problem is solved. Contact customer support.
Install additional printer memory, and then resend the print job.
Did the job print?
The problem is solved. Go to step 2.
a From the document you are trying to print, open the Print dialog and
check if you have selected the correct printer.
Do the jobs print?
The problem is solved. Go to step 3.
a Check if the printer is plugged in and turned on, and if Ready appears
on the printer display. b Resend the print job.
Do the jobs print?
The problem is solved. Go to step 4.
If an error message appears on the printer display, then clear the message.
Do the jobs print?
The problem is solved. Go to step 5.
a Check if the ports (USB, serial, or Ethernet) are working and if the
cables are securely connected to the computer and the printer.
Do the jobs print?

The problem is solved. Go to step 6.
a Turn off the printer, then wait for about 10 seconds, and then turn the
printer back on. b Resend the print job.
Do the jobs print?
The problem is solved. Contact customer support.
a Remove, and then reinstall the printer software. For more
information, see “Installing the printer software” on page 37.
Do the jobs print?
The problem is solved. Go to step 2.
a Make sure the size of the paper loaded in the tray matches the fuser
type.
Does the print speed increase?
The problem is solved. Contact customer support.
a Replace the fuser.
For more information on installing the fuser, see the instruction sheet that came with the part. b Resend the print job.
Does the print speed increase?

The problem is solved. Go to step 2.
a Open the trays, and then check if they contain paper of the same size
and type.
Do the trays link correctly?
The problem is solved. Contact customer support.
a From the printer control panel, set the paper size and type in the Paper
menu to match the paper loaded in the trays to be linked.
Do the trays link correctly?
The problem is solved. Go to step 2.
Adjust the print timeout settings.
a From the printer control panel, navigate to:
Settings > General Settings > Timeouts > Print Timeout
b Select a higher setting, and then press . c Resend the print job.
Did the file print correctly?
The problem is solved. Contact customer support.
a Check the original file for manual page breaks. b Resend the print job.
Did the file print correctly?


Go to step 2. Select a font that is supported by the printer.
a Print a font sample list to check if the fonts you are using are supported
Menus > Reports > Print Fonts 2 Select PCL Fonts or PostScript Fonts. b Resend the print job.
Are you using fonts that are supported by the printer?
Check if the fonts installed on the computer are supported by the printer.
Are the fonts installed on the computer supported by the printer?

a Move the width and length guides in the tray to the correct positions
for the paper loaded. b Resend the print job.
Troubleshooting 216

Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Do the paper size and type match the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.
Is the page or image clipped?
Contact customer support.
The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge. 2 Remove the imaging unit.
Is the page or image clipped?
The problem is solved. Go to step 2.
a Make sure the size of the paper loaded in the tray matches the fuser
type.
Do compressed images still appear?


For more information on installing the fuser, see the instruction sheet that came with the part. b Resend the print job.

a From the Quality Menu on the printer control panel, decrease the
a Remove the toner cartridge. b Remove the imaging unit.
Replace the imaging unit, and then resend the print job.
Troubleshooting 218


a Make sure your software program is using a correct fill pattern. b Resend the print job.
a Load the specified tray or feeder with a recommended type of paper. b Resend the print job.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Replace the imaging unit, and then resend the print job.
Troubleshooting 219

ABC DEF ABC DEF
The problem is solved. Go to step 2.
a Move the width and length guides in the tray to the correct positions
for the paper size loaded. b Resend the print job.
Are the margins correct?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size in the Paper menu to match the paper loaded in the tray.
Does the paper size match the paper loaded in the tray?
The problem is solved. Contact customer support.
a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.
Are the margins correct?

Go to step 2. Adjust the width and length guides.
Move the width and length guides in the tray to the correct positions for the size of the paper loaded.
Are the width and length guides positioned correctly?
Go to step 3. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the paper still curled?
Go to step 5. The problem is solved.
a Remove the paper from the tray, and then turn it over. b Resend the print job.
Is the paper still curled?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Is the paper still curled?
) ) ABCDE
ABCDE ABCDE

Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded in the tray. b Resend the print job.
Do print irregularities still appear?
Go to step 3. Specify the paper size and type from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Do the printer settings match the type and weight of the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do print irregularities still appear?
From the printer control panel, set the paper texture in the Paper menu to match the paper loaded in the tray.
Go to step 5.
Check if the paper loaded in the tray has texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Do print irregularities still appear?
Contact customer support at http://support.lexmar k.com or your service representative.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do print irregularities still appear?

ABC DEF ABC DEF
Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, reduce the toner
darkness.
Is the print still too dark?
Go to step 3. Do one or more of the following:
a From the printer control panel, set the paper type, texture and weight
in the Paper menu to match the paper loaded in the tray. b Resend the print job.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type, texture
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too dark?
Step 4 Check if the paper loaded in the tray has texture or rough finishes.
From the printer control panel, change the texture settings in the Paper Texture menu to match the paper you are printing on.
Go to step 5.
Are you printing on textured or rough paper?

Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too dark?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the print still too dark?
ABC DEF
Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, increase the toner
darkness.
Is the print still too light?
Go to step 3. Change the paper type, texture, and weight to match the paper loaded in the tray.
From the printer control panel, set the paper type, texture, and weight in the Paper menu to match the paper loaded in the tray.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too light?

From the printer control panel, change the texture settings in the Paper Texture menu to match the paper you are printing on.
Go to step 5.
Make sure that the paper has no texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too light?
Go to step 7. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Is the print still too light?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the print still too light?

Go to step 2. The problem is solved.
a Check if there is packing material left on the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Check if the packing material is properly removed from the imaging unit.
Is the printer still printing blank pages?
Go to step 3. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Is the printer still printing blank pages?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the printer still printing blank pages?

Go to step 2. The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge, and then the imaging unit.
Is the printer printing solid black pages?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the printer printing solid black pages?
Go to step 2. The problem is solved.
a Replace the imaging unit if the distance between the defects is equal
to any of the following:
Do repeating defects still appear on prints?
Contact customer support.
The problem is solved.
a Replace the fuser if the distance between the defects is equal to either
of the following:
Do repeating defects still appear on prints?


Go to step 2. Load paper with the correct paper type and weight in the tray.
Load paper with the correct paper type and weight in the tray.
Is paper with the correct paper type and weight loaded in the tray?
Go to step 3. Change the paper loaded in the tray to match the paper type and weight specified in the tray settings.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Is the tray set to the type and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do shadow images still appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do shadow images still appear on prints?
) ) ABCDE
ABCDE ABCDE

Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded. b Resend the print job.
Is the print still skewed?
Contact customer support.
The problem is solved.
a Check if you are printing on a paper that is supported by the tray. b Resend the print job.
Is the print still skewed?
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the tray or feeder from
Printing Preferences or the Print dialog. b Resend the print job.
Do streaked horizontal lines appear on prints?
Go to step 3. Change the paper type and weight to match the paper loaded in the tray.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked horizontal lines appear on prints?


1 Remove the toner cartridge, and then the imaging unit.
Replace the imaging unit, and then resend the print job.
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do streaked vertical lines appear on prints?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper texture, type, and weight in the Paper menu to match the paper loaded in the tray.
Do the paper texture, type, and weight match the paper in the tray?

Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked vertical lines appear on prints?
Go to step 5. The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge, and then the imaging unit.
Do streaked vertical lines appear on prints?
Contact customer support at http://support.lexmar k.com or your service representative.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do streaked vertical lines appear on prints?
Replace the imaging unit, and then resend the print job.
Contact customer support.
The problem is solved.
Do toner specks appear on prints?
ABCDE
ABCDE ABCDE


1 Remove the toner cartridge, and then the imaging unit.
Did the toner fog or background shading disappear from the prints?
Replace the imaging unit, and then resend the print job.
Did the toner fog or background shading disappear from the prints?

Go to step 2. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
From the Paper menu on the printer control panel, check the paper type and weight.
Do the paper type and weight match the paper loaded in the tray?
From the Paper menu on the printer control panel, set the paper texture.
Check if you are printing on paper with texture or rough finishes.
a From the Paper Weight menu on the printer control panel, set Heavy
Troubleshooting 232

Contact customer support.
The problem is solved.
a Enable Quiet mode.
From the printer control panel, navigate to:
Settings > General Settings > Quiet Mode > On b Resend the print job.
Does the toner rub off?
Go to step 2. Set the paper type to Transparency.
From the printer control panel, set the paper type in the Paper menu to match the paper loaded in the tray.
Is the paper type for the tray set to Transparency?
Contact customer support.
The problem is solved.
a Check if you are using a recommended type of transparency. b Resend the print job.
Is the print quality still poor?
Replace the imaging unit, and then resend the print job.
Contact customer support.
The problem is solved.
Is the print density uneven?

Go to step 2. The problem is solved.
a Make sure your software program is using a correct fill pattern. b Resend the print job.
Do vertical voids appear on prints?
Go to step 3. The problem is solved.
a From the printer control panel, set the paper type and weight in the
Paper menu to match the paper loaded in the tray. b Resend the print job.
Do vertical voids appear on prints?
Step 3 Check if you are using a recommended type of paper.
Go to step 4. The problem is solved.
a Load the specified tray or feeder with a recommended type of paper. b Resend the print job.
Do vertical voids appear on prints?
Go to step 5. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Do vertical voids appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do vertical voids appear on prints?

Step 1 Make sure the printer IP address is correct.
Go to step 2. Type the correct printer IP address in the address field of your Web browser.
View the printer IP address:
Is the printer IP address correct?
Go to step 3. Turn on the printer.
Check if the printer is turned on.
Is the printer turned on?
Go to step 4. Contact your system support person.
Check if the network connection is working.
Is the network connection working?
Go to step 5. Tighten the cable connection.
Make sure the cable connections to the printer and print server are secure.
For more information, see the setup documentation that came with the printer.
Are the cable connections to the printer and print server secure?
Go to step 6. Contact your system support person.
Temporarily disable the Web proxy servers.
Are the Web proxy servers disabled?
Step 6 Access the Embedded Web Server again by typing the correct IP address in the address field.
The problem is solved. Contact customer support.
Did the Embedded Web Server open?
When you contact customer support, you will need to be able to describe the problem you are experiencing, the message on the printer display, and the troubleshooting steps you have already taken to find a solution.

You need to know your printer model type and serial number. For more information, see the label at the back of the printer. The serial number is also listed on the menu settings page.
Lexmark has various ways to help you solve your printing problem. Visit the Lexmark Web site at http://support.lexmark.com, and then select one of the following:
Tech Library You can browse our library of manuals, support documentation, drivers, and other downloads to help you
solve common problems.
E-mail You can send an e-mail to the Lexmark team, describing your problem. A service representative will respond and provide you with information to solve your problem.
Live chat You can chat directly with a service representative. They can work with you to solve your printer problem or provide assistance through Assisted Service where the service representative can remotely connect to your computer through the Internet to troubleshoot problems, install updates, or complete other tasks to help you successfully use your Lexmark product.
Telephone support is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, visit http://support.lexmark.com.
Troubleshooting 236

Product name:
Lexmark MS710 and MS711
Machine type:
Model(s):
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
© 2013 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
832, 835 · June 2013

Lexmark, Lexmark with diamond design, MarkNet, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
The following terms are trademarks or registered trademarks of these companies:

CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Agfa Corporation

All other trademarks are the property of their respective owners.
AirPrint and the AirPrint logo are trademarks of Apple, Inc.
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232–3000
All licensing notices associated with this product can be viewed from the root directory of the installation software CD.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Printing 56 dBA

1-meter average sound pressure, dBA
Values are subject to change. See www.lexmark.com for current values.
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products.
If you have further questions about recycling options, click EU Waste Electronics Information.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.
This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching the metal frame of the printer.
Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
Ready 32 dBA

Ambient operating temperature 15.6 to 32.2°C (60 to 90°F)
Shipping temperature -40 to 43.3°C (-40 to 110°F)
Storage temperature and relative humidity 1 to 35°C (34 to 95°F)
8 to 80% RH
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Chapter I, Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 10 milliwatt gallium arsenide laser operating in the wavelength of 787-800 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
A laser notice label may be affixed to this printer as shown:
Opasnost - Nevidljivo lasersko zračenje kada su kasete uklonjene i poništena sigurnosna veza. Izbjegavati izlaganje zracima.
NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, ze zařízení je vysíláno neviditelné laserové záření. Nevystavujte se působení laserového paprsku.
FARE - Usynlig laserstråling, når patroner fjernes, og spærreanordningen er slået fra. Undgå at blive udsat for laserstrålen.
VAARA - Näkymätöntä lasersäteilyä on varottava, kun värikasetit on poistettu ja lukitus on auki. Vältä lasersäteelle altistumista.
ΚΙΝΔΥΝΟΣ - Έκλυση αόρατης ακτινοβολίας laser κατά την αφαίρεση των κασετών και την απασφάλιση της μανδάλωσης. Αποφεύγετε την έκθεση στην ακτινοβολία laser. VESZÉLY – Nem látható lézersugárzás fordulhat elő a patronok eltávolításakor és a zárószerkezet felbontásakor. Kerülje a lézersugárnak való kitettséget.
FARE – Usynlig laserstråling når kassettene tas ut og sperren er satt ut av spill. Unngå eksponering for laserstrålen.
Pozor – Nebezpečenstvo neviditeľného laserového žiarenia pri odobratých kazetách a odblokovanej poistke. Nevystavujte sa lúčom.
FARA – Osynlig laserstrålning när patroner tas ur och spärrmekanismen är upphävd. Undvik exponering för laserstrålen.
危险 - 当移除碳粉盒及互锁失效时会产生看不见的激光辐射,请避免暴露在激光光束下。
危険 - カートリッジが取り外され、内部ロックが無効になると、見えないレーザー光が放射されます。 このレーザー光に当たらないようにしてください。
Power consumption
Product power consumption
The following table documents the power consumption characteristics of the product.

Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs. MS710, 780; MS711, 800
Copy The product is generating hard‑copy output from hard‑copy original documents.
Scan The product is scanning hard‑copy documents. N/A
Ready The product is waiting for a print job. Ready 1, 100; Ready 2, 75
Sleep Mode The product is in a high‑level energy‑saving mode. 4.8
Hibernate The product is in a low‑level energy‑saving mode. 0.5
Off The product is plugged into an electrical outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.
This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 30
By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 180 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
This product is designed with an ultra‑low power operating mode called Hibernate mode. When operating in Hibernate Mode, all other systems and devices are powered down safely.
The Hibernate mode can be entered in any of the following methods:
Factory default Hibernate Timeout for this product in all countries or regions except for EU countries and Switzerland
Factory default value for this product in EU countries or regions and Switzerland 3 days
The amount of time the printer waits after a job is printed before it enters Hibernate mode can be modified between one hour and one month.
Disabled

If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the electrical outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
この装置は、クラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この 装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをしてください。
VCCI-B
European Community (EC) directives conformity
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and the ecodesign of energy- related products.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.

This section contains the following regulatory information pertaining to wireless products that contain transmitters, for example, but not limited to, wireless network cards or proximity card readers.
This product may contain the following modular component(s):
Lexmark Regulatory Type/LEX-M01-005; FCC ID: IYLLEXM01005; Industry Canada IC: 2376A-M01005
The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.
This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb
The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.
Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement.
Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada.
En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.
Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur et loin des fenêtres afin de garantir une protection optimale.

Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc-sc.gc.ca/rpb
Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme aux spécifications techniques d'Industry Canada.
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, radio equipment and telecommunications terminal equipment and on the ecodesign of energy-related products.
Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
Products equipped with 2.4GHz Wireless LAN option are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment and on the ecodesign of energy-related products.
Compliance is indicated by the CE marking.
Operation is allowed in all EU and EFTA countries, but is restricted to indoor use only.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product may be used in the countries indicated in the table below.
AT BE BG CH CY CZ DE DK EE
EL ES FI FR HR HU IE IS IT
LI LT LU LV MT NL NO PL PT

Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.
Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.
Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.
Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.
Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.
Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.
Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky
príslušné ustanovenia smernice 1999/5/ES.

Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
LEXMARK LED PRINTERS, AND LEXMARK MULTIFUNCTION LASER PRINTERS
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country- specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Transfer/Transport Units, Paper Feed items, if any, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.

Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
As part of your warranty service and/or replacement, Lexmark may update the firmware in your printer to the latest version. Firmware updates may modify printer settings and cause counterfeit and/or unauthorized products, supplies, parts, materials (such as toners and inks), software, or interfaces to stop working. Authorized use of genuine Lexmark products will not be impacted.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES.

This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Elliptic Curve Cryptography (ECC) Cipher Suites for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Elliptic Curve Cipher Suites with SHA-256/382 and AES Galois Counter Mode (GCM) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Suite B Profile for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Addition of the Camellia Cipher Suites to Transport Layer Security (TLS) implemented in the product or service.
The use of certain patents in this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for AES-CCM ECC Cipher Suites for TLS implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for IKE and IKEv2 Authentication Using the Eliptic Curve Digital Signature Algorithm (ECDSA) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Suite B Cryptographic Suites for IPSec implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Algorithms for Internet Key Exchange version 1 (IKEv1) implemented in the product or service.







Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.