
User's Guide
Machine type(s):
Model(s):
630, 635, 646


Connect the power cord to a properly grounded electrical outlet that is near the product and easily accessible.
Do not place or use this product near water or wet locations.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
Use only the power cord provided with this product or the manufacturer's authorized replacement.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a service representative.
Safety information 6

SAVE THESE INSTRUCTIONS.
Safety information 7

Using this guide
This User’s Guide provides general and specific information on using the printer models that are listed on the cover page.
The following chapters contain information applicable to all printer models:
To find instructions for your printer:
Overview 8

Overview 9

Selecting a location for the printer 10
When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any options, then leave enough room for them also. It is important to:


Selecting a location for the printer 11


Additional printer setup 12
Installing internal options
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
– Parallel 1284‑B interface – MarkNet N8130 10/100 fiber interface – RS‑232‑C serial interface
* This internal option is available only in the MS610de printer model.
Access the controller board to install internal options.
For MS510dn and MS610dn, see “Accessing the controller board” on page 40. For MS610de, see “Accessing the controller board” on page 74.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.

Additional printer setup 13
1 Access the controller board.
For the MS510dn and MS610dn printer models, see “Accessing the controller board” on page 40.
For the MS610de printer model, see “Accessing the controller board” on page 74.
2 Unpack the optional card.
3 Holding the card by its sides, align the plastic pins (1) on the card with the holes (2) on the controller board.



Additional printer setup 14
4 Push the card firmly into place as shown in the illustration.

5 For the MS510dn and MS610dn printer models, close the controller board access door.
For the MS610de printer model, close the controller board shield, and then close the access door.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.

Additional printer setup 15
An optional memory card can be purchased separately and attached to the controller board.
1 Access the controller board. For the MS510dn and MS610dn printer models, see “Accessing the controller board” on page 40. For the MS610de printer model, see “Accessing the controller board” on page 74.
2 Unpack the memory card.
3 Align the notch (1) on the memory card with the ridge (2) on the connector.

4 Push the memory card straight into the connector and forward into the controller board wall until it clicks into place.


5 For the MS510dn and MS610dn printer models, close the controller board access door.
For the MS610de printer model, close the controller board shield, and then close the access door.

Additional printer setup 16
The controller board supports one optional LexmarkTM Internal Solutions Port (ISP). This option is supported only in MS610de printer model.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Open the controller board access door.


Additional printer setup 17
2 Lightly press the stop on the left side of the access door, and then slide the access door to remove it.

3 Unpack the ISP kit.


2 Screw to attach the ISP to the bracket
4 Screws to attach the ISP metal bracket to the printer cage

Additional printer setup 18
4 Place the plastic bracket inside the ISP exterior cover until it clicks into place.


5 Slide and push the ISP solution into the plastic bracket.


6 Secure the ISP solution to the plastic bracket using the long screw.



Additional printer setup 19
7 Tighten the two screws on the end of the ISP solution.


8 Attach the white plug of the ISP solution interface cable into the white receptacle on the ISP.



Additional printer setup 20
9 Attach the ISP exterior cover at an angle by inserting the left hinges first.

10 Lower the rest of the cover, and then slide the cover to the right.


Additional printer setup 21
11 Run the ISP cable through the controller board shield.


12 Open the shield using the green handle.

13 Attach the blue plug of the ISP solution interface cable into the blue receptacle on the controller board.

Additional printer setup 22


14 Close the shield.
15 Close the ISP exterior cover.

Additional printer setup 23
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 74
2 Unpack the printer hard disk.
3 Install the printer hard disk on the controller board:



Additional printer setup 24
b Align the screws on the printer hard disk to the slots on the controller board bracket, and then slide the printer
hard disk onto the brackets.

c Tighten the two screws.


d Insert the plug of the printer hard disk interface cable into the receptacle of the controller board.

Additional printer setup 25

4 Close the controller board shield, and then close the access door.
1 Access the controller board. For MS610de printer model, see “Accessing the controller board” on page 74.
2 Loosen the screws that connect the printer hard disk to the controller board bracket.

Additional printer setup 26
3 Unplug the printer hard disk interface cable from the receptacle in the controller board , leaving the cable attached to the printer hard disk. To unplug the cable, squeeze the paddle at the plug of the interface cable to disengage the latch before pulling the cable out.

4 Hold the printer hard disk by the edges, and then remove it from the printer.
5 Close the controller board shield, and then close the access door.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer using the power switch, and then unplug the power cord from the electrical outlet.


2 Unpack the tray, and then remove all packing materials.

Additional printer setup 27
3 Pull the tray completely out of the base.

4 Remove any packing material from inside the tray.
5 Insert the tray into the base.
6 Place the tray near the printer.
7 Align the printer with the tray, and then lower the printer into place.

8 Connect the power cord to the printer, then to a properly grounded electrical outlet, and then turn on the printer.

Additional printer setup 28
To uninstall the optional trays, slide the latch on the right side of the printer toward the front of the printer until it clicks into place, and then remove stacked trays one at a time from the top to the bottom.
2 Do either of the following: • If you are using the Software and Documentation CD, then insert the CD and wait for the installation dialog to appear. If the installation dialog does not appear, then do the following:
From the Search charm, type run, and then navigate to: Apps list > Run > type D:\setup.exe > OK.
, or click Start and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
c Press Enter, or click OK.
a Click

Additional printer setup 29
Click the CD icon on the desktop. • If you are using the downloaded software installer from the Web, then double‑click the installer that you have saved in your computer. Wait for the Select Installation Type dialog to appear, and then click Install.
3 Click Install, and then follow the instructions on the computer screen.
When any hardware options are installed, you may need to manually add the options in the printer driver to make them available for use.
1 Open the printers folder.
From the Search charm, type run, and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
4 Click the Configuration tab.
6 Click Apply.
In Windows 8 · a Click

Additional printer setup 30
2 Add any installed hardware options, and then click OK.
To configure your printer to connect to an Ethernet network, organize the following information before you begin:
You will need an Ethernet cable to connect the printer to the network and an available port where the printer can physically connect to the network. Use a new network cable when possible to avoid potential problems caused by a damaged cable.
2 Do either of the following: • If you are using the Software and Documentation CD, then insert the CD and wait for the installation dialog to appear. If the installation dialog does not appear, then do the following:

Additional printer setup 31
From the Search charm, type run, and then navigate to: Apps list > Run > type D:\setup.exe > OK
In Windows 7 or earlier
, or click Start and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
c Press Enter, or click OK.
3 Click Install, and then follow the instructions on the computer screen.
4 Select Ethernet connection, and then click Continue.
5 Attach the Ethernet cable when instructed to do so.
6 Select the printer from the list, and then click Continue.
7 Follow the instructions on the computer screen.
1 Allow the network DHCP server to assign an IP address to the printer.
3 Install the printer driver on the computer. a Insert the Software and Documentation CD, and then double‑click the installer package for the printer. b Follow the instructions on the computer screen.
c Select a destination, and then click Continue. d From the Easy Install screen, click Install. e Type the user password, and then click OK.
All the necessary applications are installed on the computer. f Click Close when installation is complete.
4 Add the printer. • For IP printing: a From the Apple menu, navigate to either of the following:
– System Preferences > Print & Scan – System Preferences > Print & Fax
In Windows 8 · a Click

Additional printer setup 32
b Click +.
c If necessary, click Add Printer or Scanner or Add Other Printer or Scanner. d Click the IP tab. e Type the printer IP address in the address field, and then click Add. • For AppleTalk printing:
– Make sure AppleTalk is activated on your printer. – This feature is supported only in Mac OS X version 10.5. a From the Apple menu, navigate to:
System Preferences > Print & Fax b Click +, and then navigate to:
AppleTalk > select your printer > Add
Make sure you have the following information before setting up the printer on a wireless network:
Some ad hoc networks will also require the automatic setting. Check with your system support person if you are not sure which channel to select. • Security Method—There are three basic options for Security Method: – WEP key
If your network uses more than one WEP key, then enter up to four in the provided spaces. Select the key currently in use on the network by selecting the default WEP transmit key. or – WPA or WPA2 preshared key or passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network. – 802.1X–RADIUS
If you are installing the printer on an 802.1X network, then you may need the following:

Additional printer setup 33
If your wireless network does not use any type of security, then you will not have any security information.
– If you do not know the SSID of the network that your computer is connected to, then launch the wireless utility
of the computer network adapter, and then look for the network name. If you cannot find the SSID or the security information for your network, then see the documentation that came with the access point, or contact your system support person. – To find the WPA/WPA2 preshared key/passphrase for the wireless network, see the documentation that came
with the access point, see the Web page associated with the access point, or consult your system support person.
Before you begin, make sure that:
– > Settings > > Network/Ports > > Active NIC > > Auto >
> Network/Ports > Active NIC > Auto
1 Depending on your printer model, navigate to either of the following:
> Wireless Connection Setup >
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wireless Connection Setup
2 Select a wireless connection setup.
Search for networks Show available wireless connections.
Enter a network name Manually type the SSID.
Wi‑Fi Protected Setup Connect the printer to a wireless network using Wi‑Fi Protected Setup.
3 Follow the instructions on the printer display.
Use To

Additional printer setup 34
Connecting the printer to a wireless network using the Wi‑Fi Protected Setup
Before connecting the printer to a wireless network, make sure that:
1 Depending on your printer model, navigate to either of the following:
> Wi‑Fi Protected Setup > > Start Push Button Method >
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wi‑Fi Protected Setup > Start Push Button Method
2 Follow the instructions on the printer display.
1 Depending on your printer model, navigate to either of the following:
> Wi‑Fi Protected Setup > > Start PIN Method >
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wi‑Fi Protected Setup > Start PIN Method
2 Copy the eight‑digit WPS PIN.
3 Open a Web browser, and then type the IP address of your access point in the address field.
4 Access the WPS settings. For more information, see the documentation that came with your access point.
5 Enter the eight‑digit PIN, and then save the setting.
Before you begin, make sure that:
1 Open a Web browser, and then type the printer IP address in the address field.

Additional printer setup 35
2 Click Settings > Network/Ports > Wireless.
3 Modify the settings to match the settings of your access point (wireless router).
4 Click Submit.
5 Turn off the printer, and then disconnect the Ethernet cable. Then wait for at least five seconds, and then turn the printer back on.
6 To verify if your printer is connected to the network, print a network setup page. Then in the Network Card [x] section, see if the status is “Connected”.
For more information, see the “Verifying printer setup” section of the User’s Guide.
When all hardware and software options are installed and the printer is turned on, verify that the printer is set up correctly by printing the following:

Using MS510dn and MS610dn 36
Learning about the printer


1 Printer control panel
4 Front door release button
5 Controller board access door
6 100‑sheet multipurpose feeder
7 Standard 250‑sheet tray
8 Optional 250‑ or 550‑sheet trays
2 Paper stop · 3 Standard bin

Using MS510dn and MS610dn 37



8 Optional 250‑ or 550‑sheet trays
1 2 3 4 5 6 7

8 9 10 11 12 13


Using MS510dn and MS610dn 38

7 Sleep button Enable Sleep mode or Hibernate mode.
The following actions wake the printer from Sleep mode:
8 USB port Connect a flash drive to the printer.
9 Stop or cancel button Stop all printer activities.
13 Indicator light Check the status of the printer.
The colors of the Sleep button and indicator lights on the printer control panel signify a certain printer status or condition.

Off The printer is off or in Hibernate mode.
Blinking green The printer is warming up, processing data, or printing.
Off The printer is off, idle or in Ready state.
Blinking amber The printer is entering or waking from Hibernate mode.
Blinking amber for 0.1 second, then goes completely off for 1.9 seconds in a slow, pulsing pattern

Using MS510dn and MS610dn 39
Connect the printer to the computer using a USB or parallel cable, or to the network using an Ethernet cable.
Make sure to match the following:

1 USB port Attach an optional wireless network adapter.
2 USB printer port Connect the printer to a computer.
3 Ethernet port Connect the printer to an Ethernet network.
Connect the printer to a computer.
5 Power switch Turn on or turn off the printer.
6 Printer power cord socket Connect the printer to an electrical outlet.
7 Security slot Attach a lock that will secure the printer in place.
Use the To · 4 Parallel port

Using MS510dn and MS610dn 40
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Open the controller board access door.

2 Use the following illustration to locate the appropriate connector.

1 Memory card connector
2 Option card connector

Using MS510dn and MS610dn 41
The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 181 and “Storing paper” on page 118.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Paper Size/Type >
2 Press the up or down arrow button to select the tray or feeder, and then press .
3 Press the up or down arrow button to select the paper size, and then press .
4 Press the up or down arrow button to select the paper type, and then press to change the settings.
The Universal paper size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Universal Setup > > Units of Measure > > select a unit of
2 Select Portrait Width or Portrait Height, and then press .
3 Press the left or right arrow button to change the setting, and then press .
The standard bin holds up to 150 sheets of 75‑g/m2 (20‑lb) paper. It collects prints facedown. The standard bin includes a paper stop that keeps paper from sliding out the front of the bin as it stacks.
measure >

Using MS510dn and MS610dn 42
To open the paper stop, pull it so that it flips forward.

1 Pull out the tray completely.

LTR
EXEC
B5
A5
A6

Using MS510dn and MS610dn 43
2 Squeeze and then slide the width guide tab to the correct position for the size of the paper you are loading.

A4 B5 A5
EXEC

LTR
A4
B5
A5
3 Squeeze and then slide the length guide tab to the correct position for the size of the paper you are loading.


EXEC
B5 A5 A6
A4
B5
EXEC
LTR
A5

Using MS510dn and MS610dn 44


4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.


Using MS510dn and MS610dn 45
5 Load the paper stack.



EXEC
B5 A5 A6
A4
B5
EXEC
LTR
A5

Using MS510dn and MS610dn 46
6 Insert the tray.

7 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.
Use the multipurpose feeder when printing on different paper sizes and types or specialty media, such as card stock, transparencies, paper labels, and envelopes. You can also use it for single‑page print jobs on letterhead.
1 Open the multipurpose feeder.



Using MS510dn and MS610dn 47
a Pull the multipurpose feeder extender.

b Pull the extender gently so that the multipurpose feeder is fully extended and open.

2 Squeeze the tab on the left width guide, and then move the guides for the paper you are loading.



Using MS510dn and MS610dn 48
3 Prepare the paper or specialty media for loading. • Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

4 Load the paper or specialty media.

Using MS510dn and MS610dn 49






Using MS510dn and MS610dn 50
5 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper or specialty media loaded in the multipurpose feeder.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu.
4 Click Submit.

Using MS510dn and MS610dn 51
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Select a custom name, and then type a new custom paper type name.
4 Click Submit.
5 Click Custom Types, and then verify if the new custom paper type name has replaced the custom name.
Using the printer control panel
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Custom Names
2 Select a custom name, and then type a new custom paper type name.
3 Press .
4 Press Custom Types, and then verify if the new custom paper type name has replaced the custom name.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Types.
3 Select a custom paper type name, and then select a paper type.
4 Click Submit.

Using MS510dn and MS610dn 52
Using the printer control panel
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Custom Types
2 Select a custom paper type name, and then select a paper type.
3 Press .
1 From the Paper menu on the printer control panel, set the paper type and size to match the paper loaded.
2 Send the print job:
a With a document open, click File > Print. b Click Properties, Preferences, Options, or Setup.
c Adjust the settings, if necessary. d Click OK > Print.
a Customize the settings in the Page Setup dialog if necessary:
1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the paper loaded. 3 Click OK. b Customize the settings in the Page Setup dialog if necessary:
1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options. 2 From the Print dialog and pop‑up menus adjust the settings if necessary.
Using the Embedded Web Server
1 Open a Web browser, and then type the IP address of the printer in the address field.
For Windows users · For Macintosh users

Using MS510dn and MS610dn 53
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the toner darkness, and then click Submit.
Using the printer control panel
1 From the printer control panel, navigate to:
> Settings > > Print Settings > > Quality Menu > > Toner Darkness
2 Adjust the toner darkness, and then press .
1 Insert a flash drive into the USB port.


Using MS510dn and MS610dn 54

2 From the printer control panel, select the document you want to print.
3 Press the left or right arrow button to specify the number of copies for printing, and then press .
Flash drive File type
Documents:
Images:

Using MS510dn and MS610dn 55
To download a compatible mobile printing application, visit www.lexmark.com/mobile.
1 From the printer control panel, navigate to:
> Security > Confidential Print
2 Select a print job type.
Confidential Job Expiration Hold print jobs in the computer until you enter the PIN from the printer control panel.
Max Invalid PIN Limit the number of times an invalid PIN can be entered.
Repeat Job Expiration Print and store print jobs in the printer memory.
Reserve Job Expiration Store print jobs for printing at a later time.
Verify Job Expiration Print one copy of a print job and hold the remaining copies. It lets you examine if the first copy is satisfactory.
3 Press .
Use To

Using MS510dn and MS610dn 56
1 With a document open, click File > Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click Print and Hold.
4 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
5 Click OK or Print.
1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2 From the print options or Copies & Pages pop‑up menu, choose Job Routing.
3 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
4 Click OK or Print.
1 From the printer control panel, navigate to:
> Settings > > Reports > > Print Fonts
2 Press the up or down arrow button to select the font setting.
For Windows users · For Macintosh users

Using MS510dn and MS610dn 57
3 Press .
From the printer control panel, navigate to:
> Settings > Reports > > Print Directory >
From the printer control panel, press
> .
For Windows users
1 Open the printers folder.
From the Search charm, type run, and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
2 Double‑click the printer icon.
3 Select the print job you want to cancel.
4 Click Delete.
2 From the printer window, select the print job you want to cancel, and then delete it.
In Windows 8 · a Click

Using MS510dn and MS610dn 58
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server — Security: Administrator's Guide on the Lexmark support Web site at http://support.lexmark.com.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Check the virtual display that appears at the top left corner of the screen.
The virtual display works as an actual display would work on a printer control panel.
You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Supply Notifications.
3 From the drop‑down menu for each supply, select one of the following notification options:

Using MS510dn and MS610dn 59
Off The normal printer behavior for all supplies occurs.
E‑mail Only The printer generates an e-mail when the supply condition is reached. The status of the supply will appear on the menus page and status page.
Continuable Stop1 The printer stops processing jobs when the supply condition is reached, and the user needs to press a button to continue printing.
Non Continuable Stop1,2 The printer stops when the supply condition is reached. The supply must be replaced to continue printing.
1 The printer generates an e-mail about the status of the supply when supply notification is enabled.
2 The printer stops when some supplies become empty to prevent damage.
4 Click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings tab > Security > Confidential Print Setup.
4 Save the modified settings.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click the Copy Printer Settings.
Notification Description

Using MS510dn and MS610dn 60
3 To change the language, select a language from the drop-down menu, and then click Click here to submit language.
4 Click Printer Settings.
5 Type the IP addresses of the source and target printers in their appropriate fields.
6 Click Copy Printer Settings.
The Panel PIN Protect menu lets you restrict access to the menus from the printer control panel. To restrict access to the menus, create a Personal Identification Number (PIN), and then assign the PIN to each menu.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Security > Panel PIN Protect.
3 From the Create User PIN or Create Admin PIN sections, enter your PIN.
4 Click Modify.
5 From any menu in the Administrative Menus, Management, or Function Access sections, select User PIN Protected or Admin PIN Protected or Admin PIN and User PIN Protected.
6 Click Submit.
If you try to access a PIN‑protected menu from the printer control panel, the printer will require you to enter the PIN.
Print a menu settings page to view the current menu settings and to verify if the printer options are installed correctly.
From the printer control panel, navigate to:
> Settings > Reports > > Menu Settings Page >

Using MS510dn and MS610dn 61
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the printer control panel, navigate to:
> Settings > Reports > > Network Setup Page >
2 Check the first section of the network setup page, and confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult your system support person for a solution, and then print another network setup page.
A message appears on the printer display when a replacement supply item is needed or when maintenance is required.
From the printer control panel, navigate to:
> Status/Supplies > > View Supplies >
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Device Status > More Details.
Using Eco‑mode
Use Eco‑Mode to quickly select one or more ways to reduce your printer's environmental impact.
1 From the printer control panel, navigate to:
> Settings > Settings > > General Settings > > Eco‑Mode > > select the setting you want

Using MS510dn and MS610dn 62
Off Use the factory default settings for all settings associated with Eco‑Mode. This setting supports the performance specifications for your printer.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy and Paper modes.
2 Press .
Use Quiet mode to reduce the printer noise.
1 From the printer control panel, navigate to:
> Settings > Settings > > General Settings > > Quiet Mode >
2 Select a setting you want.
On Reduce printer noise.
Off Use factory default settings.
3 Press .
To save energy, decrease the number of minutes before the printer enters Sleep mode. Select from 1 to 120. The factory default setting is 30 minutes.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
Use To · Use To

Using MS510dn and MS610dn 63
2 Navigate to:
Settings > General Settings > Timeouts
3 In the Sleep Mode field, enter the number of minutes you want the printer to wait before it enters Sleep mode.
4 Click Submit.
Using the printer control panel
1 From the printer control panel, navigate to:
> Settings > > Settings > > General Settings > > Timeouts > > Sleep Mode >
2 In the Sleep Mode field, select the number of minutes you want the printer to wait before it enters Sleep mode.
3 Press .
Hibernate is an ultra‑low‑power operating mode. When operating in Hibernate mode, all other systems and devices are powered down safely.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Sleep Button Settings.
3 From the “Press Sleep Button” or “Press and Hold Sleep Button” drop‑down menu, select Hibernate.
4 Click Submit.

Using MS510dn and MS610dn 64
Using the printer control panel
1 From the printer control panel, navigate to:
> Settings > > Settings > > General Settings >
2 Press the arrow buttons until Press Sleep Button or Press and Hold Sleep Button appears, and
then press .
3 Press the arrow buttons until Hibernate appears, and then press .
Hibernate Timeout lets you set the amount of time the printer waits after a print job is processed before it goes into a reduced power state.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Timeouts.
3 From the Hibernate Timeout menu, select the number of hours, days, weeks, or months you want for the printer to wait before it goes into a reduced power state.
4 Click Submit.
Using the printer control panel
1 From the printer control panel, navigate to:
> Settings > > Settings > > General Settings > > Timeouts > > Hibernate Timeout >
2 Select the amount of time the printer waits after a print job is processed before it enters Hibernate mode.
3 Press .

Using MS510dn and MS610dn 65
Schedule Power Modes lets you schedule when the printer goes into a reduced power state or into the Ready state.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Schedule Power Modes.
3 From the Action menu, select the power mode.
4 From the Time menu, select the time.
5 From the Day(s) menu, select the day or days.
6 Click Add.
To save energy, or if you have trouble reading the display, adjust its brightness settings.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings.
3 In the Screen Brightness field, enter the brightness percentage you want for the display.
4 Click Submit.
If you want to keep a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings. For more information, see “Printing a menu settings page” on page 60.
If you want a more comprehensive method of restoring the printer factory default settings, then perform the Wipe All Settings option. For more information, see “Erasing non‑volatile memory” on page 67.

Using MS510dn and MS610dn 66
From the printer control panel, navigate to:
> Settings > Settings > > General Settings > > Factory Defaults > > Restore Now >
The printer is equipped with a security lock feature. Attach a security lock compatible with most laptop computers in the location shown to secure the printer in place.


Your printer contains various types of memory that can store device and network settings, and user data.
Type of memory Description
Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print jobs.
Non-volatile memory Your printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store operating system, device settings, and network information.
Erase the content of any installed printer memory in the following circumstances:

Using MS510dn and MS610dn 67
The volatile memory (RAM) installed in your printer requires a power source to retain information. To erase the buffered data, turn off the printer.
Erasing non‑volatile memory
Erase individual settings, device and network settings, security settings, and embedded solutions by following these steps:
1 Turn off the printer.
2 Hold down 2 and 6 on the keypad while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
3 Press the up or down arrow button until Wipe All Settings appears.
The printer will restart several times during this process.
4 Navigate to:
Back > Exit Config Menu
The printer will perform a power‑on reset, and then return to normal operating mode.
In high-security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer cannot be accessed by unauthorized persons. For more information, visit the Lexmark security Web page.
You can also see the Embedded Web Server — Security: Administrator’s Guide for additional information:
1 Go to www.lexmark.com, and then navigate to Support & Downloads > select your printer.
2 Click the Manuals tab, and then select Embedded Web Server — Security: Administrator’s Guide.

Learning about the printer


1 Printer control panel
4 Front door release button
5 Controller board access door
6 100‑sheet multipurpose feeder
7 Standard 550‑sheet tray
8 Optional 250‑ or 550‑sheet tray
Using MS610de 68 · 2 Paper stop · 3 Standard bin

1 2 3 4


4 Sleep button Enable Sleep mode or Hibernate mode.
The following actions wake the printer from Sleep mode:
5 Stop or cancel button Stop all printer activity.
6 Indicator light Check the status of the printer.
7 USB port Connect a flash drive to the printer.
The colors of the Sleep button and indicator lights on the printer control panel signify a certain printer status or condition.

Off The printer is off or in Hibernate mode.
Blinking green The printer is warming up, processing data, or printing.
Using MS610de 69

Sleep button light Printer status
Off The printer is off, idle or in Ready state.
Solid amber The printer is in Sleep mode.
Blinking amber The printer is entering or waking from Hibernate mode.
Blinking amber for 0.1 second, then goes completely off for 1.9 seconds in a slow, pulsing pattern
The printer is in Hibernate mode.
When the printer is turned on, the display shows a basic screen, referred to as the home screen. Use the home screen buttons and icons to initiate an action.
1 2 3 4

5 6 7 8
1 Change Language Change the primary language of the printer.
2 Bookmarks Create, organize, and save a set of bookmarks (URLs) into a tree view of folders and file links.
3 Held Jobs Display all current held jobs.
4 USB View, select, or print photos and documents from a flash drive.
5 Menus Access printer menus.
Using MS610de 70 · Touch To

8 Tips View a context‑sensitive help information.
This may also appear on the home screen:
Search Held Jobs Search current held jobs.
Jobs by user Access print jobs saved by user.
Profiles and Solutions Access profiles and solutions.
If an attendance message affects a function, then this icon appears and the red indicator light blinks.
The IP address of your printer is located at the top left corner of the home screen and appears as four sets of numbers separated by periods. You can use the IP address when accessing the Embedded Web Server to view and remotely configure printer settings even when you are not physically near the printer.


1 Radio button Select or clear an item.
2 Up arrow Scroll up.
3 Down arrow Scroll down.
4 Accept button Save a setting.
Return to the home screen.
Open a context-sensitive Help dialog on the printer control panel.
Scroll to the left.
Scroll to the right.
Connect the printer to the computer using a USB cable or parallel cable, or to the network using an Ethernet cable.
Using MS610de 72 · Touch the To · Touch To

Make sure to match the following:

1 Security slot Attach a lock that will secure the controller board.
2 USB printer port Connect the printer to a computer.
3 USB port Connect a flash drive to the printer.
4 USB port Attach an optional wireless network adapter.
5 Ethernet port Connect the printer to an Ethernet network.
6 Power switch Turn on or off the printer.
7 Printer power cord socket Connect the printer to an electrical outlet.
Using MS610de 73 · Use the To

CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Open the controller board access door.

2 Open the controller board shield using the green handle.


3 Use the following illustration to locate the appropriate connector.
Using MS610de 74


1 Memory card connector
2 Option card connector
3 Printer hard disk connector
4 Internal Solutions Port connector
4 Close the controller board shield, and then close the controller board access door.


Using MS610de 75

The computer IP address is required when setting up home screen applications, such as:
1 Open the command window.
From the Search charm, type run, and then navigate to:
Apps list > Run > type cmd > OK
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type cmd.
c Press Enter, or click OK.
2 Type ipconfig, and then click Go or press Enter.
3 Look for IP Address.
The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123.
1 From the Apple menu, navigate to:
System Preferences > Network
2 Click Ethernet, Wi‑Fi, or AirPort.
3 Click Advanced > TCP/IP.
4 Look for IPv4 Address.
Using MS610de 76 · In Windows 8 · a Click

You can find the printer IP address:
The Embedded Web Server is the printer Web page that lets you view and remotely configure printer settings even when you are not physically near the printer.
2 Open a Web browser, and then type the printer IP address in the address field.
3 Press Enter.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Do one or more of the following: • Show or hide the icons of basic printer functions. a Click Settings > General Settings > Home screen customization. b Select the check boxes to specify which icons appear on the home screen.
Using MS610de 77

Your printer comes with preinstalled home screen applications. Before you can use these applications, you must first activate and set up these applications using the Embedded Web Server. For more information on accessing the Embedded Web Server, see “Accessing the Embedded Web Server” on page 77.
For more information on configuring and using the home screen applications, do the following:
1 Go to http://support.lexmark.com.
3 Click the Manuals tab, and then select the document for the home screen application.

The application lets you customize the background and idle screen of your printer home screen.
1 From the home screen, navigate to:
Change Background > select background to use

The application helps you simplify and streamline work processes by letting you quickly find and print frequently used online forms directly from the printer home screen.

1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Apps > Apps Management > Forms and Favorites.
3 Define the bookmarks, and then customize the settings.
4 Click Apply.
To use the application, touch Forms and Favorites on the printer home screen, and then navigate through form categories, or search for forms based on a form number, name, or description.
Understanding Eco‑Settings
The application lets you easily manage energy consumption, noise, toner, and paper usage settings to help reduce the environmental impact of your printer.
This application enables you to interact with the printer control panel even when you are not physically near the network printer. From your computer, you can view the printer status, release held print jobs, create bookmarks, and do other print-related tasks.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Remote Operator Panel Settings.
3 Select the Enable check box, and then customize the settings.
4 Click Submit.
To use the application, click Remote Operator Panel > Launch VNC Applet.
You can export configuration settings into a text file, and then import the file to apply the settings to other printers.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Apps > Apps Management.
Using MS610de 79 · Icon Description

3 From the list of installed applications, click the name of the application you want to configure.
4 Click Configure, and then do one of the following: • To export a configuration to a file, click Export, and then follow the instructions on the computer screen to save the configuration file.
– When saving the configuration file, you can type a unique file name or use the default name. – If a "JVM Out of Memory” error occurs, then repeat the export process until the configuration file is
saved. • To import a configuration from a file, click Import, and then browse to the saved configuration file that was exported from a previously configured printer.
– Before importing the configuration file, you can choose to preview it first or load it directly. – If a timeout occurs and a blank screen appears, then refresh the Web browser, and then click Apply.
The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 181 and “Storing paper” on page 118.
From the home screen navigate to:
> Paper Menu > Paper Size/Type > select a tray > select the paper size or type >
The Universal paper size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus.
1 From the printer control panel, navigate to:
> Paper Menu > Universal Setup > Units of Measure > select a unit of measure >
2 Touch Portrait Width or Portrait Height.
3 Select the width or height, and then touch
Using MS610de 80

The standard bin holds up to 150 sheets of 75‑g/m2 (20‑lb) paper. It collects prints facedown. The standard bin includes a paper stop that keeps paper from sliding out the front of the bin as it stacks.
To open the paper stop, pull it so that it flips forward.

1 Pull out the tray completely.
Using MS610de 81

LTR
EXEC
B5
A5
A6
2 Squeeze and then slide the width guide tab to the correct position for the size of the paper you are loading.
EXEC
A4 B5 A5
B5
EXEC
LTR
A4
A5
Using MS610de 82

3 Squeeze and then slide the length guide tab to the correct position for the size of the paper you are loading.
EXEC
B5 A5 A6
EXEC
LTR
A4
B5
A5
Using MS610de 83


4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper stack.

Using MS610de 84

EXEC
B5 A5 A6
A4
B5
EXEC
LTR
A5
6 Insert the tray.
7 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.
Using MS610de 85

Use the multipurpose feeder when printing on different paper sizes and types or specialty media, such as card stock, transparencies, paper labels, and envelopes. You can also use it for single‑page print jobs on letterhead.
1 Open the multipurpose feeder.
a Pull the multipurpose feeder extender.
b Pull the extender gently so that the multipurpose feeder is fully extended and open.
Using MS610de 86

2 Squeeze the tab on the left width guide, and then move the guides for the paper you are loading.

3 Prepare the paper or specialty media for loading. • Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

4 Load the paper or specialty media.
Using MS610de 87

Using MS610de 88

5 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper or specialty media loaded in the multipurpose feeder.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu.
4 Click Submit.
Using MS610de 89

Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Select a custom name, and then type a custom paper type name.
4 Click Submit.
5 Click Custom Types, and then verify if the new custom paper type name has replaced the custom name.
Using the printer control panel
1 From the home screen, navigate to:
> Paper Menu > Custom Names
2 Select a custom name, and then type a custom paper type name.
4 Touch Custom Types, and then verify that the new custom paper type name has replaced the custom name.
Using the Embedded Web Server
Assign a custom paper type name to a tray when linking or unlinking trays.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Types.
Using MS610de 90 · 3 Touch

3 Select a custom paper type name, and then select a paper type
4 Click Submit.
Using the printer control panel
1 From the home screen, navigate to:
> Paper Menu > Custom Types
2 Select a custom paper type name, and then select a paper type
Use the Forms and Favorites application to quickly and easily access frequently used forms or other information that is regularly printed. Before you can use this application, first set it up on the printer. For more information, see “Setting up Forms and Favorites” on page 78.
1 From the printer home screen, navigate to:
Forms and Favorites > select the form from the list > enter the number of copies > adjust other settings
2 Depending on your printer model, touch
, or Submit.
1 From the Paper menu on the printer control panel, set the paper type and size to match the paper loaded.
2 Send the print job:
a With a document open, click File > Print. b Click Properties, Preferences, Options, or Setup.
c Adjust the settings, if necessary. d Click OK > Print.
a Customize the settings in the Page Setup dialog:
1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the paper loaded. 3 Click OK.

b Customize the settings in the Print dialog:
1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options. 2 From the Print dialog and pop‑up menus, adjust the settings if necessary.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the setting, and then click Submit.
Using the printer control panel
1 From the home screen, navigate to:
> Settings > Print Settings > Quality Menu > Toner Darkness
2 Adjust the setting, and then touch
Using MS610de 92

1 Insert a flash drive into the USB port.

Using MS610de 93


2 From the printer control panel, touch the document you want to print.
3 Touch the arrows to specify the number of copies for printing, and then touch Print.
Flash drive File type
Documents:
Images:
To download a compatible mobile printing application, visit www.lexmark.com/mobile.
Using MS610de 94

1 From the home screen, navigate to:
> Security > Confidential Print > select a print job type
Max Invalid PIN Limit the number of times an invalid PIN can be entered.
Confidential Job Expiration Hold print jobs in the computer until you enter the PIN from the printer control panel.
Repeat Job Expiration Print and store print jobs in the printer memory.
Verify Job Expiration Print one copy of a print job and hold the remaining copies. It lets you examine if the first copy is satisfactory or not. The print job is automatically deleted from the printer memory when all copies are printed.
Reserve Job Expiration Store print jobs for printing at a later time.
1 With a document open, click File > Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click Print and Hold.
4 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
5 Click OK or Print.

1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2 From the print options or Copies & Pages pop‑up menu, choose Job Routing.
3 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
4 Click OK or Print.
1 From the home screen, navigate to:
> Reports > Print Fonts
2 Touch PCL Fonts or PostScript Fonts.
A directory list shows the resources stored in a flash memory or on the printer hard disk.
From the home screen, navigate to:
> Reports > Print Directory
Using MS610de 96 · For Macintosh users

1 From the printer control panel, touch Cancel Job or press
on the keypad.
2 Touch the print job you want to cancel, and then touch Delete Selected Jobs.
on the keypad, then touch Resume to return to the home screen.
For Windows users
1 Open the printers folder.
From the Search charm, type Run, and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
, or click Start and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
2 Double‑click the printer icon.
3 Select the print job you want to cancel.
4 Click Delete.
2 From the printer window, select the print job you want to cancel, and then delete it.
Use serial printing to print when the computer is far from the printer or to print at a reduced speed.
Using MS610de 97 · In Windows 8 · a Click

After installing the serial or communication (COM) port, configure the printer and the computer. Make sure you have connected the serial cable to the COM port on your printer.
1 Set the parameters in the printer. a From the printer control panel, navigate to the menu for the port settings. b Locate the menu for the serial port settings, and then adjust the settings, if necessary.
c Save the modified settings, and then print a menu settings page.
2 Install the printer driver. a Obtain a copy of the software installer package.
From the Search charm type run, and then navigate to: Apps list > Run > type D:\setup.exe > OK
, or click Start and then click Run. 2 In the Start Search or Run dialog, type D:\setup.exe. 3 Press Enter or click OK.
f From the Configure Printer Connection dialog, select a port. g If the port is not in the list, then click Refresh, or navigate to:
Add port > select a port type > enter the necessary information > OK h Click Continue > Finish.
3 Set the COM port parameters.
After installing the printer driver, set the serial parameters in the COM port assigned to the printer driver.
Using MS610de 98 · 1 Click

From the Search charm, type run and then navigate to: Apps list > Run > type devmgmt.msc > OK
, or click Start and then click Run. 2 In the Start Search or Run dialog, type devmgmt.msc. 3 Press Enter or click OK. b Double‑click Ports (COM & LPT) to expand the list of available ports.
c Do either of the following:
Check the serial heading of the menu settings page for the printer settings. f Click OK, and then close all the dialogs. g Print a test page to verify printer installation.
When a new Lexmark Internal Solutions Port (ISP) is installed in the printer, the printer configurations on computers that access the printer must be updated since the printer will be assigned a new IP address. All computers that access the printer must be updated with this new IP address.
1 Open a Web browser, and then type the printer IP address in the address field.
Using MS610de 99 · 1 Click

2 Open the printers folder.
From the Search charm, type Run and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
, or click Start and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
4 Click the Ports tab.
5 Select the port from the list, and then click Configure Port.
6 Type the new IP address in the “Printer Name or IP Address” field.
7 Click OK > Close.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Add the printer. • For IP printing: a From the Apple menu, navigate to either of the following:
– System Preferences > Print & Scan – System Preferences > Print & Fax b Click +.
c Click the IP tab. d Type the printer IP address in the address field, and then click Add. • For AppleTalk printing:
– Make sure AppleTalk is activated on your printer. – This feature is supported only in Mac OS X version 10.5.
Using MS610de 100 · In Windows 8 · a Click

a From the Apple menu, navigate to:
System Preferences > Print & Fax b Click +, and then navigate to:
AppleTalk > select the printer > Add
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server — Security: Administrator's Guide on the Lexmark support Web site at http://support.lexmark.com.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Check the virtual display that appears at the top left corner of the screen.
The virtual display works as an actual display would work on a printer control panel.
You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Supply Notifications.
3 From the drop‑down menu for each supply, select one of the following notification options:
Using MS610de 101

Off The normal printer behavior for all supplies occurs.
E‑mail Only The printer generates an e‑mail when the supply condition is reached. The status of the supply appears on the menus page and status page.
Continuable Stop1 The printer stops processing jobs when the supply condition is reached, and the user needs to press a button to continue printing.
Non Continuable Stop1,2 The printer stops processing jobs when the supply condition is reached. The supply must be replaced to continue printing.
1 The printer generates an e-mail about the status of the supply when supply notification is enabled.
2 The printer stops when some supplies become empty to prevent damage.
4 Click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Security > Confidential Print Setup.
4 Click Submit to save the modified settings.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Copy Printer Settings.
3 To change the language, select a language from the drop‑down menu, and then click Click here to submit language.
Using MS610de 102 · Notification Description

4 Click Printer Settings.
5 Type the IP addresses of the source and target printers.
6 Click Copy Printer Settings.
The Panel PIN Protect menu lets you restrict access to the menus from the printer control panel. To restrict access to the menus, create a Personal Identification Number (PIN), and then assign the PIN to each menu.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Security > Panel PIN Protect.
3 From the Create User PIN or Create Admin PIN section, enter your PIN.
4 Click Modify.
5 From any menu in the Administrative Menus, Management, or Function Access sections, select User PIN Protected, Admin PIN Protected, or Admin PIN and User PIN Protected.
6 Click Submit.
If you try to access a PIN‑protected menu from the printer control panel, then the printer will require you to enter the PIN.
From the home screen, navigate to:
> Reports > Menu Settings Page
Using MS610de 103

If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the home screen, navigate to:
> Reports > Network Setup Page
2 Check the first section of the network setup page, and confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult a system support person for a solution, and then print another network setup page.
A message appears on the printer display when a replacement supply item is needed or when maintenance is required.
From the home screen, touch Status/Supplies > View Supplies.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Device Status > More Details.
Using Eco‑Mode
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Eco‑Mode > select a setting
Using MS610de 104

Off Use the factory default settings for all settings associated with Eco‑Mode. Off supports the performance specifications of the printer.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy and Paper modes.
3 Click Submit.
Enable Quiet Mode to reduce printer noise.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Quiet Mode > select a setting
On Reduce printer noise.
Off Use factory default settings.
3 Click Submit.
Using MS610de 105 · Use To · Use To

To save energy, decrease the number of minutes the printer waits before it enters Sleep mode. Select from 1 to 120. The factory default setting is 30 minutes.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Timeouts.
3 In the Sleep Mode field, enter the number of minutes you want for the printer to wait before it enters Sleep mode.
4 Click Submit.
Using the printer control panel
1 From the home screen, navigate to:
> Settings > General Settings > Timeouts > Sleep Mode
2 In the Sleep Mode field, select the number of minutes you want for the printer to wait before it enters Sleep mode.
Hibernate is an ultra‑low‑power operating mode. When operating in Hibernate mode, the printer is essentially off, and all other systems and devices are powered down safely.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Sleep Button Settings.
Using MS610de 106 · 3 Touch

3 From the “Press Sleep Button” or “Press and Hold Sleep Button” drop‑down menu, select Hibernate.
4 Click Submit.
Using the printer control panel
1 From the home screen, navigate to:
> Settings > General Settings
2 Touch Press Sleep Button or Press and Hold Sleep Button.
3 Touch Hibernate >
Hibernate Timeout lets you set the amount of time the printer waits after a print job is processed before it goes into a reduced power state.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Timeouts.
3 From the Hibernate Timeout menu, select the number of hours, days, weeks, or months you want for the printer to wait before it goes into a reduced power state.
4 Click Submit.
Using the printer control panel
1 From the printer control panel, navigate to:
> Settings > General Settings > Timeouts > Hibernate Timeout
2 Select the amount of time the printer waits after a print job is processed before it enters Hibernate mode.
Using MS610de 107 · 3 Touch

Schedule Power Modes lets you schedule when the printer goes into a reduced power state or into the Ready state.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Schedule Power Modes.
3 From the Action menu, select the power mode.
4 From the Time menu, select the time.
5 From the Day(s) menu, select the day or days.
6 Click Add.
To save energy, or if you are have trouble reading your display, adjust the brightness of the display.
Available settings range from 20–100. The factory default setting is 100.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings.
3 In the Screen Brightness field, enter the brightness percentage you want for the display.
4 Click Submit.
Using the printer control panel
1 From the home screen, navigate to:
> Settings > General Settings > Screen Brightness
2 In the Screen Brightness field, enter the brightness percentage you want for the display.
Using MS610de 108 · 3 Touch

If you want to keep a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings. For more information, see “Printing a menu settings page” on page 103.
If you want a more comprehensive method of restoring the printer factory default settings, then perform the Wipe All Settings option. For more information, see “Erasing non‑volatile memory” on page 111.
From the home screen, navigate to:
> Settings > General Settings > Factory Defaults > Restore Now >
Attach a lock that is compatible with most laptop computers in the location shown to prevent access to the controller board.


Your printer contains various types of memory that can store device and network settings, and user data.
Using MS610de 109

Type of memory Description
Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print jobs.
Non-volatile memory Your printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store the operating system, device settings, network information and bookmark settings, and embedded solutions.
Hard disk memory Some printers have a hard disk drive installed. The printer hard disk is designed for printer-specific functionality. This lets the printer retain buffered user data from complex print jobs, as well as form data, and font data.
Erase the content of any installed printer memory in the following circumstances:
Disposing of a printer hard disk
In high‑security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer hard disk cannot be accessed when the printer—or its hard disk—is removed from your premises.
The volatile memory (RAM) installed in your printer requires a power source to retain information. To erase the buffered data, simply turn off the printer.
Using MS610de 110

Erasing non‑volatile memory
Erase individual settings, device and network settings, security settings, and embedded solutions by following these steps:
1 Turn off the printer.
2 Hold down 2 and 6 on the keypad while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display instead of the standard home screen icons.
3 Touch Wipe All Settings.
The printer will restart several times during this process.
4 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.
Using the printer control panel
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, the touch screen displays a list of functions.
4 Touch Yes to proceed with disk wiping.
5 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.
Using MS610de 111

Enable hard disk encryption to prevent loss of sensitive data in the event the printer or its hard disk is stolen.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Security > Disk Encryption.
3 From the Disk encryption menu, select Enable.
4 Click Submit.
Using the printer control panel
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
3 Touch Disk Encryption > Enable.
4 Touch Yes to proceed with disk wiping.
5 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.
Using MS610de 112

In high-security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer cannot be accessed by unauthorized persons. For more information, visit the Lexmark security Web page.
You can also see the Embedded Web Server — Security: Administrator’s Guide for additional information:
1 Go to www.lexmark.com, and then navigate to Support & Downloads > select your printer.
2 Click the Manuals tab, and then select Embedded Web Server — Security: Administrator’s Guide.
Using MS610de 113

Paper and specialty media guide 114
Using specialty media
Card stock is heavy, single‑ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly impact print quality. Print samples on the card stock being considered for use before buying large quantities.
When printing on card stock:
Print samples on the envelopes being considered for use before buying large quantities.

Paper and specialty media guide 115
Print samples on the labels being considered for use before buying large quantities.
For more information on label printing, characteristics, and design, see the Card Stock & Label Guide available at http://support.lexmark.com.
When printing on labels:
releasing hazardous emissions. – Label adhesives, face sheet (printable stock), and topcoats can withstand up to 172‑kPa (25‑psi) pressure without

Paper and specialty media guide 116
Selecting the correct paper or specialty media reduces printing problems. For the best print quality, try a sample of the paper or specialty media before buying large quantities.
The following paper characteristics affect print quality and reliability. Consider these characteristics when evaluating new paper stock.
The printer trays can automatically feed paper weights up to 120‑g/m2 (32‑lb) bond grain long paper. The multipurpose feeder can automatically feed paper weights up to 163‑g/m2 (43‑lb) bond grain long paper. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 75‑g/m2 (20‑lb) bond grain long paper. For paper smaller than 182 x 257 mm (7.2 x 10.1 inches), we recommended to use 90 g/m2
(24 lb) or heavier paper.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.
Paper smoothness directly affects print quality. If paper is too rough, then toner cannot fuse to it properly. If paper is too smooth, then it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; however, smoothness between 150 and 250 Sheffield points produces the best print quality.
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.
Store paper in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extend the time to several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60–90‑g/m2 (16–24‑lb) bond paper, grain long paper is recommended.

Paper and specialty media guide 117
Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton can negatively affect paper handling.
The following paper types are not recommended for use with the printer:
Using the appropriate paper prevents jams and helps ensure trouble‑free printing.
To help avoid paper jams and poor print quality:
Use these guidelines when selecting preprinted forms and letterhead:
Use papers printed with heat‑resistant inks designed for use in xerographic copiers. The ink must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions. Use inks that are not affected by the resin in toner. Inks that are oxidation‑set or oil‑based generally meet these requirements; latex inks might not. When in doubt, contact the paper supplier.

Paper and specialty media guide 118
Preprinted papers such as letterhead must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser (electrophotographic) printers. In 1998, Lexmark presented to the US government a study demonstrating that recycled paper produced by major mills in the US fed as well as non-recycled paper. However, no blanket statement can be made that all recycled paper will feed well.
Lexmark consistently tests its printers with recycled paper (20–100% post-consumer waste) and a variety of test paper from around the world, using chamber tests for different temperature and humidity conditions. Lexmark has found no reason to discourage the use of today's recycled office papers, but generally the following property guidelines apply to recycled paper.
Recycled paper, paper of lower weight (
Use these paper storage guidelines to help avoid jams and uneven print quality:

Paper and specialty media guide 119
Paper size Standard tray Optional 250‑ or 550‑sheet tray Multipurpose feeder Duplex mode
210 x 297 mm (8.3 x 11.7 in.)
148 x 210 mm (5.8 x 8.3 in.)
105 x 148 mm (4.1 x 5.8 in.)
182 x 257 mm (7.2 x 10.1 in.)
216 x 279 mm (8.5 x 11 in.)
216 x 356 mm (8.5 x 14 in.)
184 x 267 mm (7.3 x 10.5 in.)
216 x 340 mm (8.5 x 13.4 in.)
216 x 330 mm (8.5 x 13 in.)
140 x 216 mm (5.5 x 8.5 in.)
76.2 x 127 mm (3 x 5 in.) up to 216 x 356 mm (8.5 x 14 in.)
7 3/4 Envelope (Monarch)
98 x 191 mm (3.9 x 7.5 in.)
98 x 225 mm (3.9 x 8.9 in.)
1 This size setting formats the page for 216 x 356 mm (8.5 x 14 in.) unless the size is specified by the software application.
2 Universal is supported only in the standard tray if the paper size is at least 105 x 148 mm (4.1 x 5.8 in.). Universal is supported only in the optional 250- or 550-sheet tray if the paper size is at least 148 x 210 mm (5.8 x 8.3 in.). Universal is only supported in duplex mode if the width is at least 210 mm (8.3 in.) and length is at least 279 mm (11 in.). The smallest supported Universal size is only supported in the multipurpose feeder.

Paper and specialty media guide 120
Paper size Standard tray Optional 250‑ or 550‑sheet tray Multipurpose feeder Duplex mode
105 x 241 mm (4.1 x 9.5 in.)
110 x 220 mm (4.3 x 8.7 in.)
C5 Envelope 162 x 229 mm (6.4 x 9 in.) X X X
176 x 250 mm (6.9 x 9.8 in.)
229 x 356 mm (9 x 14 in.)
1 This size setting formats the page for 216 x 356 mm (8.5 x 14 in.) unless the size is specified by the software application.
2 Universal is supported only in the standard tray if the paper size is at least 105 x 148 mm (4.1 x 5.8 in.). Universal is supported only in the optional 250- or 550-sheet tray if the paper size is at least 148 x 210 mm (5.8 x 8.3 in.). Universal is only supported in duplex mode if the width is at least 210 mm (8.3 in.) and length is at least 279 mm (11 in.). The smallest supported Universal size is only supported in the multipurpose feeder.
The standard tray supports 60–90‑g/m2 (16–24‑lb) paper weights. The optional tray supports 60–120‑g/m2 (16–32‑lb) paper weights. The multipurpose feeder supports 60–163‑g/m2 (16–43‑lb) paper weights.

Paper type 250‑ or 550‑sheet tray Multipurpose feeder Duplex mode

Paper and specialty media guide 121
Paper type 250‑ or 550‑sheet tray Multipurpose feeder Duplex mode
1 One‑sided paper labels designed for laser printers are supported for occasional use. It is recommended to print 20 or fewer pages of paper labels per month. Vinyl, pharmacy, and two‑sided labels are not supported.
2 Bond and Heavy Paper are supported in duplex mode up to 90‑g/m2 (24‑lb) paper weight.

Understanding the printer menus 122
Menus list
Paper Menu Reports Network/Ports
Default Source Paper Size/Type
Menu Settings Page Device Statistics
Network Setup Page2
Profiles List Print Fonts
Miscellaneous Security Settings4
Flash Drive Menu4
Erase Temporary Data Files4
Set Date and Time
Menu Map Information Guide
1 This menu appears only in touch‑screen printer models.
2 Depending on the printer setup, this menu item appears as Network Setup Page or Network [x] Setup Page.
3 Depending on the printer setup, this menu item appears as Standard Network or Network [x].
4 This feature is available only in select printer models.

Understanding the printer menus 123
Set a default paper source for all print jobs.
Tray [x] Multipurpose Feeder Manual Paper Manual Envelope
Specify the paper size loaded in each tray.
A4 A5 A6 JIS‑B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the type of paper loaded in each tray.
Plain Paper Transparency Recycled Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]

Understanding the printer menus 124
Specify the paper size loaded in the multipurpose feeder.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the type of paper loaded in the multipurpose feeder.
Plain Paper Card Stock Transparency Recycled Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Use To · Multipurpose Feeder Size · Multipurpose Feeder Type

Understanding the printer menus 125
Specify the paper size being manually loaded.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the paper type being manually loaded.
Plain Paper Card Stock Transparency Recycled Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Specify the envelope size being manually loaded.
7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the envelope type being manually loaded.
Envelope Rough Envelope Custom Type [x]

Understanding the printer menus 126
Determine when the printer selects paper from the multipurpose feeder.
Substitute a specified paper size if the requested paper size is not available.
Off Statement/A5 Letter/A4 All Listed
Specify the relative texture of the plain paper loaded.
Specify the relative texture of the card stock loaded.
Specify the relative texture of the transparencies loaded.
Specify the relative texture of the recycled paper loaded.

Understanding the printer menus 127
Specify the relative texture of the labels loaded.
Specify the relative texture of the bond paper loaded.
Specify the relative texture of the envelopes loaded.
Specify the relative texture of the rough envelopes loaded.
Specify the relative texture of the letterhead loaded.
Specify the relative texture of the preprinted paper loaded.
Specify the relative texture of the colored paper loaded.
Specify the relative texture of the paper loaded.
Specify the relative texture of the paper loaded.
Specify the relative texture of the cotton paper loaded.
Specify the relative texture of the custom paper loaded.

Understanding the printer menus 128
Specify the relative weight of the plain paper loaded.
Specify the relative weight of the card stock loaded.
Specify the relative weight of the transparencies loaded.
Specify the relative weight of the recycled paper loaded.
Specify the relative weight of the labels loaded.
Specify the relative weight of the bond paper loaded.
Specify the relative weight of the envelope loaded.
Specify the relative weight of the rough envelope loaded.
Specify the relative weight of the letterhead loaded.
Specify the relative weight of the preprinted paper loaded.

Understanding the printer menus 129
Specify the relative weight of the colored paper loaded.
Specify that the weight of the paper loaded is light.
Specify that the weight of the paper loaded is heavy.
Specify the relative weight of the cotton or rough paper loaded.
Specify the relative weight of the custom paper loaded.
Determine and set two‑sided printing for all print jobs that specify Recycled as the paper type.
Determine and set two‑sided printing for all print jobs that specify Bond as the paper type.
Determine and set two‑sided printing for all print jobs that specify Letterhead as the paper type.
Determine and set two‑sided printing for all print jobs that specify Preprinted as the paper type.
Determine and set two‑sided printing for all print jobs that specify Colored as the paper type.

Understanding the printer menus 130
Determine and set two‑sided printing for all print jobs that specify Light as the paper type.
Determine and set two‑sided printing for all print jobs that specify Heavy as the paper type.
Determine and set two‑sided printing for all print jobs that specify Custom [x] as the paper type.
Associate a paper or specialty media type with a factory default Custom Type [x] name or a user‑defined custom name created in the Embedded Web Server or MarkVisionTM Professional. The user‑defined name appears instead of Custom Type [x].
Paper Card Stock Transparency Rough/Cotton Labels Envelope
Specify a paper type when the Recycled setting is selected in other menus.
Paper Card Stock Transparency Rough/Cotton Labels Envelope Cotton
Custom Name [x] Specify a custom name for a paper type. This name replaces the Custom Type [x] name in the printer menus.

Understanding the printer menus 131
Identify the units of measure.
Set the portrait width.
3–8.5 inches 76–216 mm
Set the portrait height.
3–14.17 inches 76–360 mm
Specify the feed direction if the paper can be loaded in either direction.
Short Edge Long Edge
Menu Settings Page Print a report containing information about the paper loaded in trays, installed memory, total page count, alarms, timeouts, printer control panel language, TCP/IP address, status of supplies, status of the network connection, and other information.
Device Statistics Print a report containing printer statistics such as supply information and details about printed pages.
![Page 132 of the Lexmark MS610DN user manual — Standard Network or Network [x] menus](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-132.webp?w=400)
Understanding the printer menus 132
Network Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address information.
Profiles List Print a list of profiles stored in the printer.
Print a report of all the fonts available for the printer language currently set in the printer.
PCL Fonts PostScript Fonts
Print Directory Print a list of all the resources stored in an optional flash memory card or printer hard disk.
Asset Report Print a report containing printer asset information, such as serial number and model name.
Auto [list of available network cards]
Set the printer to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language.

Understanding the printer menus 133
Set the printer to automatically switch to PS emulation when a print job requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.
Set the size of the network input buffer.
Auto 3KB to [maximum size allowed]
Temporarily store print jobs in the printer hard disk before printing. This menu only appears when a formatted disk is installed.
Set the printer to process Macintosh binary PostScript print jobs.

Understanding the printer menus 134
Standard Network Setup OR Network [x] Setup
Display and set the printer network settings.
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
To access the menu, navigate to any of the following:
Print Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address.
To access the menu, navigate to either of the following:
View the connection status of the network card.
View Card Speed View the speed of an active network card.
View the network addresses.
Job Timeout 0–255 seconds Set the amount of time it takes for a network print job to be canceled.

Understanding the printer menus 135
To access the menu, navigate to any of the following:
Set Hostname Set the host name.
IP Address View or change the current TCP/IP address.
Netmask View or change the current TCP/IP netmask.
Gateway View or change the current TCP/IP gateway.
Specify the DHCP address and parameter assignment.
Specify the RARP address assignment setting.
Specify the BOOTP address assignment setting.
Specify the Zero Configuration Networking setting.
Enable the built-in FTP server, which lets you send files to the printer using File Transfer Protocol.
Enable the built-in Web server (Embedded Web Server). When enabled, the printer can be monitored and managed remotely using a Web browser.
WINS Server Address View or change the current WINS server address.

Understanding the printer menus 136
View or change the current DDNS setting.
View or change the current mDNS setting.
DNS Server Address View or change the current DNS server address.
Backup DNS Server Address View or change the backup DNS server addresses.
Backup DNS Server Address 2
Backup DNS Server Address 3
View or change the current HTTPS setting.
To access the menu, navigate to any of the following:
Enable Internet Protocol Version Six (IPv6) in the printer.
IPv6 uses bigger numbers to create IP addresses.
Specify whether or not the network adapter accepts the automatic IPv6 address configuration entries provided by a router.
Set Hostname* Set the host name.
View Address* View the current IPv6 addresses.
View Router Address* View the current router address.
Enable DHCPv6 in the printer.
* These settings can be changed only from the Embedded Web Server.

Understanding the printer menus 137
To access the menu, navigate to any of the following:
Wi‑Fi Protected Setup (WPS)
Establish a wireless network and enable network security.
Start Push Button Method Start PIN Method
Enable/Disable WPS Auto‑detection
Automatically detect the connection method that an access point with WPS uses—Start Push Button Method or Start PIN Method.
Specify the network mode.
Specify the wireless standard for the wireless network.
802.11b/g 802.11b/g/n
Choose Network Select an available network for the printer to use.
View Signal Quality View the quality of the wireless connection.
View Security Mode View the encryption method for the wireless network.
To access the menu, navigate to any of the following:

Understanding the printer menus 138
Enable or disable AppleTalk support.
View Name Show the assigned AppleTalk name.
View Address Show the assigned AppleTalk address.
Provide a list of AppleTalk zones available on the network.
[list of zones available on the network]
Set the printer to automatically switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.
![Page 139 of the Lexmark MS610DN user manual — Parallel [x] menu](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-139.webp?w=400)
Understanding the printer menus 139
Set the size of the USB input buffer.
Disabled Auto 3K to [maximum size allowed]
Temporarily store print jobs in the printer hard disk before printing.
Set the printer to process Macintosh binary PostScript print jobs.
Set the network address information for an external print server.
yyy.yyy.yyy.yyy
Set the netmask information for an external print server.
yyy.yyy.yyy.yyy
Set the gateway information for an external print server.
yyy.yyy.yyy.yyy
![Page 140 of the Lexmark MS610DN user manual — Parallel [x] menu](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-140.webp?w=400)
Understanding the printer menus 140
Set the printer to automatically switch to PCL emulation when a print job received through a serial port requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job received through a serial port requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.
Set the size of the parallel input buffer.
Disabled Auto 3K to [maximum size allowed]
Temporarily store print jobs on the printer hard disk before printing.
![Page 141 of the Lexmark MS610DN user manual — Parallel [x] menu](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-141.webp?w=400)
Understanding the printer menus 141
Enable bidirectional communication through the parallel port.
Specify the parallel port protocol.
Determine if the printer honors printer hardware initialization requests from the computer.
Determine if the parallel port data is sampled on the leading or trailing edge of a strobe.
Set the printer to process Macintosh binary PostScript print jobs.
Set the network address information for an external print server.
yyy.yyy.yyy.yyy
Set the netmask information for an external print server.
yyy.yyy.yyy.yyy
Set the gateway information for an external print server.
yyy.yyy.yyy.yyy

Understanding the printer menus 142
Primary SMTP Gateway Specify SMTP server gateway and port information.
Secondary SMTP Gateway Port
5–30 Specify the amount of time in seconds before the server stops trying to send an e‑mail.
Reply Address Specify a reply address of up to 128 characters in the e-mail sent by the printer.
Set the printer to use SSL for increased security when connecting to the SMTP server.
Specify the type of user authentication required for printing privileges.
No authentication required Login/Plain CRAM‑MD5 Digest‑MD5 NTLM Kerberos 5
Device‑Initiated E‑mail
Specify what credentials will be used when communicating to the SMTP server. Some SMTP servers require credentials to send an e-mail.
None Use Device SMTP Credentials

Understanding the printer menus 143
Limit the number and time frames of failed login attempts from the printer control panel before all users are locked out.
Login failures* Failure time frame* Lockout time* Panel Login Timeout Remote Login Timeout
1–16 Limit the digit length of the PIN.
* These menus appear only in touch-screen printer models.
Limit the number of times an invalid PIN can be entered.
Limit the amount of time a confidential print job stays in the printer before it is deleted.
Off 1 hour 4 hours 24 hours 1 week

Understanding the printer menus 144
Set a time limit on how long the printer stores print jobs.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs needing verification.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs for printing at a later time.
Off 1 hour 4 hours 24 hours 1 week
Export Log Let an authorized user export the audit log.
Specify whether or not audit logs are deleted.
Delete now Do not delete

Understanding the printer menus 145
Specify how and whether or not audit logs are created.
Yes No Enable Remote Syslog
No Yes Remote Syslog Facility
0–23 Severity of events to log
Erase Temporary Data Files deletes only print job data on the printer hard disk that are not currently in use by the file system. All permanent data on the printer hard disk are preserved, such as downloaded fonts, macros, and held jobs.
Specify the mode for erasing temporary data files.
Mark all disk space used by a previous print job. This method does not permit the file system to reuse this space until it has been cleared.
Single pass Multiple pass
Current Date and Time Show the current date and time settings for the printer.
Manually Set Date and Time
Enter the date and time.

Understanding the printer menus 146
Select the time zone.
[list of time zones]
Set the printer to use the applicable daylight saving time (DST) start and end times associated with the printer Time Zone setting.
Enable Network Time Protocol, which synchronizes the clocks of devices on a network.

Understanding the printer menus 147
Set the language of the text appearing on the printer display.
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portuguese Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese
Display the estimates of the supplies on the printer control panel, Embedded Web Server, menu settings, and the device statistics reports.
Show estimates Do not show estimates
1 This menu item appears only in touch‑screen printer models.
2 This menu item appears only in non‑touch‑screen printer models.
Use To · Display Language · Show Supply Estimates

Understanding the printer menus 148
Minimize the use of energy, paper, or specialty media.
Off Energy Energy/Paper Paper
Reduce the amount of noise produced by the printer.
Instruct the printer to run the setup wizard.
1 This menu item appears only in touch‑screen printer models.
2 This menu item appears only in non‑touch‑screen printer models.

Understanding the printer menus 149
Specify a language and custom key information for the printer control panel keyboard. The additional tabs enable access to accent marks and symbols from the printer control panel keyboard.
English Francais Francais Canadien Deutsch Italiano Espanol Greek Dansk Norsk Nederlands Svenska Suomi Portuguese Russian Polski Swiss German Swiss French Korean Magyar Turkish Czech Simplified Chinese Traditional Chinese Japanese Custom Key [x]
Specify the unit of measurement for paper sizes.
1 This menu item appears only in touch‑screen printer models.
2 This menu item appears only in non‑touch‑screen printer models.

Understanding the printer menus 150
Specify what is displayed on the upper left and right corners of the home screen.
Left side Right side Custom Text [x]
For the Left side and Right side options, select from the following options:
None IP Address Hostname Contact Name Location Date/Time mDNS/DDNS Service Name Zero Configuration Name Custom Text [x] Model Name
Displayed Information (continued)1
Customize the displayed information for Black Toner.
Select from the following options:
Do not display Display Message to Display
1 This menu item appears only in touch‑screen printer models.
2 This menu item appears only in non‑touch‑screen printer models.

Understanding the printer menus 151
Displayed Information (continued)1
Customize the displayed information for Waste Toner Bottle, Paper Jam, Load Paper, and Service Errors.
Paper Jam Load Paper Service Errors
Select from the following options:
Yes No Message to Display
Change the icons and buttons that appear on the home screen.
Change Language Search Held Jobs Held Jobs USB Drive Profiles and Solutions Bookmarks Jobs by user Forms and Favorites Eco-Settings Showroom Change Background
For each icon or button, select from the following options:
Display Do not display
Format the printer date.
MM‑DD‑YYYY DD‑MM‑YYYY YYYY‑MM‑DD
Format the printer time.
12 hour A.M./P.M. 24 hour clock
Specify the brightness of the printer display.
1 This menu item appears only in touch‑screen printer models.
2 This menu item appears only in non‑touch‑screen printer models.

Understanding the printer menus 152
Specify whether icons and buttons have audio feedback.
Specify whether bookmarks are displayed from the Held Jobs area.
Web Page Refresh Rate1
Specify the number of seconds between Embedded Web Server refreshes.
Contact Name1 Specify a contact name for the printer.
Location1 Specify the location of the printer.
Specify the number of minutes of inactivity before the printer enters a lower power state.
Set the amount of time the printer waits after a job is printed before it goes into a reduced power state.
1 This menu item appears only in touch‑screen printer models.
2 This menu item appears only in non‑touch‑screen printer models.

Understanding the printer menus 153
Set the amount of time the printer waits before it enters Hibernate mode.
Disabled 1 hour 2 hours 3 hours 6 hours 1 day 2 days 3 days 1 week 2 weeks 1 month
Set the printer to Hibernate mode even if there is an active Ethernet connection.
Hibernate Timeout on Connection
Hibernate Do Not Hibernate
Set the amount of time in seconds the printer waits before returning the display to the ready state.
Display a message that lets you reset the screen timeout timer instead of returning to the home screen.
Set the amount of time in seconds the printer waits to receive an end‑of‑job message before canceling the remainder of the print job.
Set the amount of time in seconds the printer waits for additional data before canceling a print job.
1 This menu item appears only in touch‑screen printer models.
2 This menu item appears only in non‑touch‑screen printer models.

Understanding the printer menus 154
Let the printer automatically continue printing from certain offline situations when these are not resolved within the specified time period.
Specify whether the printer reprints jammed pages.
Let the printer successfully print a page that may not have printed otherwise.
Hibernate Timeout on Connection
Set the printer to hibernate mode even there is an active Ethernet connection.
Hibernate Do Not Hibernate
Determine how the printer, while in idle state, reacts to a short press of the Sleep button.
Do nothing Sleep Hibernate
Press and Hold Sleep Button
Determine how the printer, while in idle state, reacts to a long press of the Sleep button.
Do nothing Sleep Hibernate
1 This menu item appears only in touch‑screen printer models.
2 This menu item appears only in non‑touch‑screen printer models.

Understanding the printer menus 155
GUI Log Level1
Everything (0) Keys (1) Debug (2) Warnings (3) Errors (4) Critical (5) System Info (6)
Return the printer settings to the factory default settings.
Do Not Restore Restore Now
Custom Home Message2
Select a custom home message that appears as an alternating display of the printer status.
Off IP Address Hostname Contact Name Location Zero Configuration Name Custom Text [x]
Export Configuration Package1
Export files from the flash drive.
1 This menu item appears only in touch‑screen printer models.
2 This menu item appears only in non‑touch‑screen printer models.
1–999 Specify a default number of copies for each print job.
Set a default paper source for all print jobs.
Tray [x] Multipurpose Feeder Manual Paper Manual Envelope

Understanding the printer menus 156
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)
Specify whether prints are on one side or on both sides of the paper.
1 sided 2 sided
Define binding for duplexed pages in relation to paper orientation.
Long Edge Short Edge
Specify the orientation of a multiple‑page document.
Specify that multiple‑page images be printed on one side of a paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Print a border on each page image.
Specify the positioning of multiple‑page images.
Horizontal Reverse Horizontal Reverse Vertical Vertical

Understanding the printer menus 157
Specify whether blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages
Specify the paper source for separator sheets.
Tray [x] Multipurpose Feeder
Specify whether blank pages are inserted in a print job.
Do Not Print Print
Set the default printer language.
PCL Emulation PS Emulation

Understanding the printer menus 158
Set the logical and physical printable area.
Set the storage location for downloads.
Specify how the printer handles temporary downloads, such as fonts and macros stored in the RAM, when the printer receives a print job that requires more memory than is available.
Specify the order in which held and confidential jobs are printed when Print All Order is selected.
Alphabetical Oldest First Newest First

Understanding the printer menus 159
Specify whether two‑sided (duplex) printing is set as the default for all print jobs.
1 sided 2 sided
For Windows users:
1 Click File > Print. 2 Click Properties, Preferences, Options, or Setup.
For Macintosh users:
1 Choose File > Print. 2 Adjust the settings from the print dialog and pop‑up menus.
Define the way two‑sided pages are bound and printed.
Long Edge Short Edge
1–999 Specify the default number of copies for each print job.
Specify whether to insert blank pages in a print job.
Do Not Print Print
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)
Specify whether to insert blank separator sheets.
Off Between Copies Between Jobs Between Pages
Specify the paper source for separator sheets.
Tray [x] Multi‑Purpose Feeder

Understanding the printer menus 160
Print multiple‑page images on one side of a paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Specify the positioning of multiple‑page images when using Paper Saver.
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify the orientation of a multiple‑page document.
Print a border when using Paper Saver.
Specify the printed output resolution in dots per inch.
300 dpi 600 dpi 1200 dpi 1200 Image Q 2400 Image Q
Enable more pixels to print in clusters for clarity, in order to enhance images horizontally or vertically, or to enhance fonts.
Off Fonts Horizontally Vertically Both directions Isolated
1–10 Lighten or darken the printed output.

Understanding the printer menus 161
Enable a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts.
Automatically adjust the contrast enhancement applied to images.
Adjust the printed output either by lightening or darkening it. You can conserve toner by lightening the output.
‑6 to 6
0–5 Adjust the contrast of printed objects.
Determine and set if the printer creates a log of the print jobs it receives.
Job Accounting Utilities Print and delete log files or export them to a flash drive.
Determine and set how often a log file is created.
Log Action at End of Frequency
Determine and set how the printer responds when the frequency threshold expires.
None E‑mail Current Log E‑mail & Delete Current Log Post Current Log Post & Delete Current Log
Disk Near Full Level
Specify the maximum size of the log file before the printer executes the Disk Near Full Action.

Understanding the printer menus 162
Disk Near Full Action
Determine and set how the printer responds when the printer hard disk is nearly full.
None E‑mail Current Log E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post Current Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
Determine and set how the printer responds when disk usage reaches the maximum limit (100MB).
None E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
URL to Post Logs Determine and set where the printer posts job accounting logs.
E‑mail Address to Send Logs Specify the e‑mail address to which the device sends job accounting logs.
Log File Prefix Specify the prefix you want for the log file name.
Delete confidential and held jobs from the printer hard disk.
Confidential Held Not Restored All

Understanding the printer menus 163
Format the flash memory.
Delete Downloads on Disk
Delete downloads from the printer hard disk, including all held jobs, buffered jobs, and parked jobs.
Delete Now Do Not Delete
Activate Hex Trace Assist in isolating the source of a print job problem.
Provide an estimate of the percentage coverage of toner on a page. The estimate is printed on a separate page at the end of each print job.
Print a page containing information on errors, including XML markup errors.
Scale page content to fit the selected paper size.

Understanding the printer menus 164
Print annotations in a PDF.
Do Not Print Print
Print a page containing the PostScript error.
Lock PS Startup Mode
Disable the SysStart file.
Establish the font search order.
Specify the set of fonts used by the Font Name menu.
Resident Download Flash All
Identify a specific font and the option where it is stored.

Understanding the printer menus 165
Specify the symbol set for each font name.
Change the point size for scalable typographic fonts.
1.00–1008.00
Specify the font pitch for scalable monospaced fonts.
0.08–100
Specify the orientation of text and graphics on the page.
Specify the number of lines that print on each page.
Set the printer to print on A4‑size paper.
198 mm 203 mm

Understanding the printer menus 166
Specify whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command.
Auto CR after LF
Specify whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command.
Auto LF after CR
Configure the printer to work with printer software or programs that use different source assignments for trays and feeders.
Off None 0–199 Assign Tray [x]
Off None 0–199 Assign Manual Paper
Off None 0–199 Assign Manual Env
Display the factory default setting assigned to each tray or feeder.
MPF Default = 8 T1 Default = 1 T2 Default = 4 T3 Default = 5 T4 Default = 20 T5 Default = 21 Env Default = 6 MPaper Default = 2 MEnv Default = 3
Restore all tray and feeder assignments to their factory default settings.

Understanding the printer menus 167
Joanna MT Letter Gothic Lubalin Graph Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino StempelGaramond Taffy Times TimesNewRoman Univers Zapf Chancery NewSansMTCS NewSansMTCT New SansMTJA NewSansMTKO
Set the default font for HTML documents.
Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text Intl CG Times Intl Courier Intl Univers
1–255 pt Set the default font size for HTML documents.
1–400% Scale the default font for HTML documents.
Set the page orientation for HTML documents.

Understanding the printer menus 168
8–255 mm Set the page margin for HTML documents.
Specify whether to print backgrounds on HTML documents.
Do Not Print Print
Select the optimal paper size, scaling, and orientation.
Invert bitonal monochrome images.
Scale the image to fit the selected paper size.
Anchor Top Left Best Fit Anchor Center Fit Height/Width Fit Height Fit Width
Set the image orientation.
Portrait Landscape Reverse Portrait Reverse Landscape
The Help menu consists of a series of Help pages that are stored in the printer as PDFs. They contain information about using the printer and performing printing tasks.
English, French, German, and Spanish translations are stored in the printer. Other translations are available at http://support.lexmark.com.
Print All Guides Print all the guides.
Print Quality Print information about solving print quality issues.

Understanding the printer menus 169
Printing Guide Print information about loading paper and other specialty media.
Media Guide Print a list of the paper sizes supported in trays and feeders.
Print Defects Guide Print information about resolving print defects.
Menu Map Print a list of the printer control panel menus and settings.
Information Guide Print a guide in locating additional information.
Connection Guide Print information about connecting the printer locally (USB) or to a network.
Moving Guide Print instructions for safely moving the printer.
Supplies Guide Print part numbers for ordering supplies.
Use To

Saving money and the environment 170
Saving paper and toner
Studies show that as much as 80% of the carbon footprint of a printer is related to paper usage. You can significantly reduce your carbon footprint by using recycled paper and the following printing suggestions, such as printing on both sides of the paper and printing multiple pages on one side of a single sheet of paper.
For information on how you can quickly save paper and energy using one printer setting, see “Using Eco‑Mode” on page 104.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser printers. For more information on recycled papers that work well with your printer, see “Using recycled paper and other office papers” on page 118.
If your printer model supports duplex printing, then you can control whether print appears on one or two sides of the paper by selecting 2‑sided printing from the Print dialog or from the Lexmark Toolbar.
You can print up to 16 consecutive pages of a multiple‑page document onto one side of a single sheet of paper by selecting a setting from the Multipage printing (N‑Up) section of the Print dialog screen.
Before printing or making multiple copies of a document:
Correctly set the paper type and size to avoid paper jams. For more information, see “Avoiding jams” on page 181.
Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information, see:

Saving money and the environment 171
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country or region from the list.
3 Follow the instructions on the computer screen.
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark will recycle the box.
Lexmark Cartridge Collection Program diverts millions of Lexmark cartridges from landfills annually by making it both easy and free for Lexmark customers to return used cartridges to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. Boxes used to return the cartridges are also recycled.
To return Lexmark cartridges for reuse or recycling, follow the instructions that came with your printer or cartridge and use the prepaid shipping label. You can also do the following:
1 Go to www.lexmark.com/recycle.
2 From the Toner Cartridges section, select your country or region.
3 Follow the instructions on the computer screen.

Maintaining the printer 172
1 Make sure that the printer is turned off and unplugged from the electrical outlet.
2 Remove paper from the standard bin and multipurpose feeder.
3 Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.
4 Dampen a clean, lint-free cloth with water, and use it to wipe the outside of the printer.
5 Make sure all areas of the printer are dry before sending a new print job.
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, visit the Lexmark Web site at www.lexmark.com or contact the place where you purchased the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. Use of third-party supplies or parts can affect warranty coverage. Damage caused by the use of third-party supplies or parts is not covered by the warranty. All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.

Maintaining the printer 173

For the European Union, European Economic Area , and Switzerland
For the Asia Pacific Region (includes Australia and New Zealand)
For Africa, Middle East, Central Eastern Europe, and Commonwealth of Independent States
1 This cartridge is supported only in MS410d, MS410dn, MS510dn, MS610dn, and MS610de printer models.
2 This cartridge is supported only in MS510dn, MS610dn, and MS610de printer models.
For more information on countries located in each region, visit www.lexmark.com/regions.

Maintaining the printer 174
High Yield Toner Cartridge 500HA1
Extra High Yield Toner Cartridge 500XA2
Ultra High Yield Toner Cartridge 500UA3
1 This cartridge is supported only in MS310d and MS310dn printer models.
2 This cartridge is supported only in MS410d and MS410dn printer models.
3 This cartridge is supported only in MS510dn, MS610dn, and MS610de printer models.
Extremely low print coverage for extended periods of time may cause imaging unit parts to fail prior to exhaustion of toner from toner cartridge.
For more information on replacing the imaging unit, see the instruction sheet that came with the supply.
Part name Lexmark Return Program Regular
Imaging unit 500Z 500ZA
Printer model Part number
MS510dn (100v) 40X8439*
MS610dn (100v) 40X8440*
MS610de (100v) 40X8441*
* This kit is available only in Japan.

Maintaining the printer 175
The estimated number of remaining pages is based on the recent printing history of the printer. Its accuracy may vary significantly and is dependent on many factors, such as actual document content, print quality settings, and other printer settings.
The accuracy of the estimated number of remaining pages may decrease when the actual printing consumption is different from the historical printing consumption. Consider the variable level of accuracy before purchasing or replacing supplies based on the estimate. Until an adequate print history is obtained on the printer, initial estimates assume future supplies consumption based on the International Organization for Standardization* test methods and page content.
* Average continuous black declared cartridge yield in accordance with ISO/IEC 19752.
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:
1 Press the button on the right side of the printer, and then open the front door.



Maintaining the printer 176
2 Pull the toner cartridge out using the handle.

3 Unpack the toner cartridge, and then remove all packing materials.
4 Shake the new cartridge to redistribute the toner.

5 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.


6 Close the front door.

Maintaining the printer 177
1 Press the button on the right side of the printer, and then open the front door.
2 Pull the toner cartridge out using the handle.
3 Lift the green handle, and then pull the imaging unit out of the printer.


Maintaining the printer 178
4 Unpack the new imaging unit, and then shake it.

5 Remove all packing materials from the imaging unit.

6 Insert the imaging unit into the printer by aligning the arrows on the side rails of the imaging unit with the arrows on the side rails inside the printer.



Maintaining the printer 179
7 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.
8 Close the front door.


Use only the power cord provided with this product or the manufacturer's authorized replacement.

Maintaining the printer 180
The printer and its hardware options can be safely moved to another location by following these precautions:
When shipping the printer, use the original packaging or call the place of purchase for a relocation kit.

By carefully selecting paper and specialty media and loading it properly, you should be able to avoid most jams. If jams occur, then follow the steps outlined in this chapter.
Correct loading of paper Incorrect loading of paper

Clearing jams 181



When a jam occurs, a message indicating the jam location and information to clear the jam appears on the printer display. Open the doors, covers, and trays indicated on the display to remove the jam.
Clearing jams 182



Area Printer control panel message What to do
1 Standard bin [x]‑page jam, clear standard bin. [20y.xx]
Remove the jammed paper.
2 Rear door [x]‑page jam, open rear door. [20y.xx]
Open the rear door, and then remove the jammed paper.
3 Tray 1 [x]‑page jam, remove tray 1 to clear duplex. [23y.xx]
Pull tray 1 completely out, then push the front duplex flap down, and then remove the jammed paper.
4 Tray [x] [x]‑page jam, remove tray [x]. [24y.xx]
Pull the indicated tray out, and then remove the jammed paper.
[x]‑page jam, clear manual feeder. [250.xx]
Remove all paper from the multipurpose feeder, and then remove the jammed paper.
6 Front door [x]‑page jam, open front door. [20y.xx]
Open the front door, then remove the toner cartridge, imaging unit, and jammed paper.
Clearing jams 183 · 5 Multipurpose feeder
![Page 184 of the Lexmark MS610DN user manual — [x] ‑ page jam, open front door. [20y.xx]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-184.webp?w=400)
1 Press the button on the right side of the printer, and then open the front door.
2 Pull out the toner cartridge using the handle.
3 Lift the green handle, and then pull out the imaging unit from the printer.
![Lexmark MS610DN — [x] ‑ page jam, open front door. [20y.xx] diagram (page 184)](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/rimg-102.webp)
Clearing jams 184
![Page 185 of the Lexmark MS610DN user manual — [x]-page jam, open front door. [20y.xx]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-185.webp?w=400)
4 Place the imaging unit aside on a flat, smooth surface.
5 Lift the green flap in front of the printer.
![Lexmark MS610DN — [x]-page jam, open front door. [20y.xx] diagram (page 185)](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/rimg-103.webp)
6 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark MS610DN — [x]-page jam, open front door. [20y.xx] diagram (page 185)](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/rimg-104.webp)
Clearing jams 185
![Page 186 of the Lexmark MS610DN user manual — [x]-page jam, open front door. [20y.xx]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-186.webp?w=400)
7 Insert the imaging unit by aligning the arrows on the side rails of the unit with the arrows on the side rails inside the printer, and then insert the imaging unit into the printer.
8 Insert the toner cartridge by aligning the side rails of the cartridge with the arrows on the side rails inside the printer, and then insert the cartridge into the printer.
9 Close the front door.
10 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > > Clear the jam, press OK > .
Clearing jams 186
![Page 187 of the Lexmark MS610DN user manual — [x] ‑ page jam, open rear door. [20y.xx]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-187.webp?w=400)
1 Open the front door.
2 Gently pull down the rear door.
![Lexmark MS610DN — [x] ‑ page jam, open rear door. [20y.xx] diagram (page 187)](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/rimg-105.webp)
3 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 187
![Page 188 of the Lexmark MS610DN user manual — [x] ‑ page jam, clear standard bin. [20y.xx]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-188.webp?w=400)
4 Close the rear door.
to clear the message and continue printing. For non‑touch‑screen printer
5 From the printer control panel, touch
models, select Next > > Clear the jam, press OK > .
1 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark MS610DN — [x] ‑ page jam, clear standard bin. [20y.xx] diagram (page 188)](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/rimg-106.webp)
to clear the message and continue printing. For non‑touch‑screen printer
2 From the printer control panel, touch
models, select Next > > Clear the jam, press OK > .
Clearing jams 188
![Page 189 of the Lexmark MS610DN user manual — [x] ‑ page jam, remove tray 1 to clear duplex. [23y.xx]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-189.webp?w=400)
1 Pull the tray completely out of the printer.
![Lexmark MS610DN — [x] ‑ page jam, remove tray 1 to clear duplex. [23y.xx] diagram (page 189)](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/rimg-107.webp)
2 Locate the blue lever, and then pull it down to release the jam.
![Lexmark MS610DN — [x] ‑ page jam, remove tray 1 to clear duplex. [23y.xx] diagram (page 189)](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/rimg-108.webp)
![Lexmark MS610DN — [x] ‑ page jam, remove tray 1 to clear duplex. [23y.xx] diagram (page 189)](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/rimg-109.webp)
3 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 189
![Page 190 of the Lexmark MS610DN user manual — [x] ‑ page jam, open tray [x]. [24y.xx]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-190.webp?w=400)
![Lexmark MS610DN — [x]-page jam, open tray [x]. [24y.xx] diagram (page 190)](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/rimg-110.webp)
4 Insert the tray.
5 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > > Clear the jam, press OK > .
1 Pull the tray completely out of the printer.
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 190
![Page 191 of the Lexmark MS610DN user manual — [x] ‑ page jam, clear manual feeder. [25y.xx]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-191.webp?w=400)
![Lexmark MS610DN — [x]-page jam, clear manual feeder. [25y.xx] diagram (page 191)](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/rimg-111.webp)
3 Insert the tray.
to clear the message and continue printing. For non‑touch‑screen printer
4 From the printer control panel, touch
models, select Next > > Clear the jam, press OK > .
1 From the multipurpose feeder, firmly grasp the jammed paper on each side, and then gently pull it out.
2 Flex the sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.
![Lexmark MS610DN — [x] ‑ page jam, clear manual feeder. [25y.xx] diagram (page 191)](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/fig-191-1.webp)
Clearing jams 191
![Page 192 of the Lexmark MS610DN user manual — [x]-page jam, clear manual feeder. [25y.xx]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-192.webp?w=400)
3 Reload paper into the multipurpose feeder.
![Lexmark MS610DN — [x]-page jam, clear manual feeder. [25y.xx] diagram (page 192)](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/rimg-112.webp)
4 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > > Clear the jam, press OK > .
Clearing jams 192
![Page 193 of the Lexmark MS610DN user manual — Change [paper source] to [custom type name] load [orientation]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-193.webp?w=400)
Understanding the printer messages
1 Check if both the toner cartridge and imaging unit are MICR (Magnetic Ink Character Recognition) or non-MICR supplies.
2 Change the toner cartridge or imaging unit so that both are MICR or non‑MICR supplies.
You may need to order a toner cartridge. If necessary, select Continue on the printer control panel to clear the message
and continue printing. For non‑touch‑screen printer models, press to confirm.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to replace the toner cartridge very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Try one or more of the following
press to confirm. • Cancel the print job.
Troubleshooting 193
![Page 194 of the Lexmark MS610DN user manual — Configuration change, some held jobs were not restored [57]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-194.webp?w=400)
Try one or more of the following:
models, press to confirm. • Cancel the print job.
Try one or more of the following:
press to confirm. • Cancel the print job.
Try one or more of the following:
press to confirm. • Cancel the print job.
Close the front door of the printer.
Try one or more of the following:
printer models, press to confirm.
Held jobs are invalidated because of any of the following possible changes in the printer:
Troubleshooting 194
![Page 195 of the Lexmark MS610DN user manual — Imaging unit very low, [x] estimated pages remain [84.xy]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-195.webp?w=400)
From the printer control panel, select Continue to clear the message. For non-touch-screen printer models, press to confirm.
Try one or more of the following:
printer models, press to confirm. • Cancel the current print job.
Error reading USB drive. Remove USB.
An unsupported USB device is inserted. Remove the USB device, and then insert a supported one.
Error reading USB hub. Remove hub.
An unsupported USB hub has been inserted. Remove the USB hub, and then install a supported one.
You may need to order an imaging unit. If necessary, select Continue on the printer control panel to clear the message
and continue printing. For non‑touch‑screen printer models, press to confirm.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to replace the imaging unit very soon. For more information, see the "Replacing supplies" section of the User’s Guide.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Troubleshooting 195
![Page 196 of the Lexmark MS610DN user manual — Insufficient memory, some Held Jobs were deleted [37]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-196.webp?w=400)
Try one or more of the following:
Insert the indicated tray into the printer.
Install additional printer memory or select Continue on the printer control panel to disable Resource Save, clear the
message, and continue printing. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
rest of the print job. For non‑touch‑screen printer models, press to confirm. • Cancel the current print job.
Try one or more of the following:
The printer deleted some held jobs in order to process current jobs.
Troubleshooting 196
![Page 197 of the Lexmark MS610DN user manual — Load [paper source] with [paper size] [paper orientation]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-197.webp?w=400)
Select Continue to clear the message. For non-touch-screen printer models, press to confirm.
Try one or more of the following:
to confirm. • Delete other held jobs to free up additional printer memory.
Try one or more of the following:
For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
panel. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 197
![Page 198 of the Lexmark MS610DN user manual — Load manual feeder with [paper size] [paper orientation]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-198.webp?w=400)
Try one or more of the following:
control panel. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 198
![Page 199 of the Lexmark MS610DN user manual — Memory full [38]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-199.webp?w=400)
Try one or more of the following:
You may need to order a maintenance kit. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
If necessary, select Continue to clear the message and continue printing. For non‑touch‑screen printer models,
press to confirm.
For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
If necessary, select Continue to clear the message and continue printing. For non‑touch‑screen printer models,
press to confirm.
You may need to replace the maintenance kit very soon. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
to confirm. • Install additional printer memory.
Troubleshooting 199
![Page 200 of the Lexmark MS610DN user manual — Not enough free space in flash memory for resources [52]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-200.webp?w=400)
Try one or more of the following:
The printer has detected a non‑Lexmark supply or part installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components.
All life indicators are designed to function with Lexmark supplies and parts and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or associated components.
To accept any and all of these risks and to proceed with the use of non-genuine supplies or parts in your printer, press
and the # button on the printer control panel simultaneously for 15 seconds.
For non‑touch‑screen printer models, press and
on the printer control panel simultaneously for 15 seconds to clear the message and continue printing.
If you do not wish to accept these risks, then remove the third-party supply or part from your printer, and then install a genuine Lexmark supply or part.
Try one or more of the following:
Troubleshooting 200 · and hold
![Page 201 of the Lexmark MS610DN user manual — Replace cartridge, printer region mismatch [42.xy]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-201.webp?w=400)
Printer had to restart. Last job may be incomplete.
to clear the message and continue printing. For non‑touch‑screen printer
From the printer control panel, touch
models, press to confirm.
For more information, visit http://support.lexmark.com or contact customer support.
Try one or more of the following:
For information on installing the cartridge, see the “Replacing supplies” section of the User’s Guide. • If the toner cartridge is installed, then remove the unresponsive toner cartridge, and then reinstall it.
Try one or more of the following:
For information on installing the imaging unit, see the “Replacing supplies” section of the User’s Guide. • If the imaging unit is installed, then remove the unresponsive imaging unit, and then reinstall it.
Remove the paper stack from the standard bin. The printer automatically detects paper removal and resumes printing.
If removing the paper does not clear the message, then select Continue on the printer control panel. For non-touch-
screen printer models, press to confirm.
Replace the toner cartridge to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Install a toner cartridge that matches the region number of the printer. x indicates the value of the printer region. y indicates the value of the cartridge region. x and y can have the following values:
Troubleshooting 201
![Page 202 of the Lexmark MS610DN user manual — Replace unsupported imaging unit [32.xy]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-202.webp?w=400)
1 United States, Canada
2 European Economic Area (EEA), Switzerland
3 Asia Pacific, Australia, New Zealand
5 Africa, Middle East, rest of Europe
Replace the imaging unit to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
The printer is scheduled for maintenance. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact your service representative, and then report the message.
Remove the toner cartridge, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Remove the imaging unit, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
![Page 203 of the Lexmark MS610DN user manual — Standard USB port disabled [56]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-203.webp?w=400)
Try one or more of the following:
to confirm. • Turn off the printer, and then turn it back on.
SMTP server not set up. Contact system administrator.
From the printer control panel, select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
to confirm.
From the printer control panel, select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 203
![Page 204 of the Lexmark MS610DN user manual — Unsupported option in slot [x] [55]](/cdn/reader/f8/f888dd53d499e9dd8693b7a361f398d9ba27cd46a2568cf31b5e438d7790bb16/images/page-204.webp?w=400)
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra flash memory.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra trays.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Try one or more of the following:
printer models, press to confirm. • Format the flash memory.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the unsupported option card from the printer controller board, and then replace it with a supported card.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Weblink server not set up. Contact system administrator.
Select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 204

Go to step 2. Turn on the printer.
Make sure the printer is turned on.
Is the printer turned on?
Step 2 Check if the printer is in Sleep mode or Hibernate mode.
Press the Sleep button to wake the printer from Sleep mode or Hibernate mode.
Go to step 3.
Is the printer in Sleep mode or Hibernate mode?
Go to step 4. Plug one end of the power cord into the printer and the other to a properly grounded electrical outlet.
Check if one end of the power cord is plugged into the printer and the other to a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
Unplug the other electrical equipment, and then turn on the printer. If the printer does not work, then reconnect the other electrical equipment.
Go to step 5.
Check other electrical equipment plugged into the electrical outlet.
Does other electrical equipment work?
Go to step 6. Make sure to match the following:
Check if the cables connecting the printer and the computer are inserted in the correct ports.
Are the cables inserted in the correct ports?
Turn on the switch or reset the breaker.
Go to step 7.
Make sure the electrical outlet is not turned off by a switch or breaker.
Is the electrical outlet turned off by a switch or breaker?

Connect the printer power cord directly to a properly grounded electrical outlet.
Go to step 8.
Check if the printer is plugged into any surge protectors, uninterruptible power supplies, or extension cords.
Is the printer plugged into any surge protectors, uninterruptible power supplies, or extension cords?
Go to step 9. Connect the printer cable securely to the printer and the computer, print server, option, or other network device.
Check if one end of the printer cable is plugged into a port on the printer and the other to the computer, print server, option, or other network device.
Is the printer cable securely attached to the printer and the computer, print server, option, or other network device?
Step 9 Make sure to install all hardware options properly and remove any packing material.
Go to step 10. Turn off the printer, remove all packing materials, then reinstall the hardware options, and then turn on the printer.
Are all hardware options properly installed and all packing material removed?
Go to step 11. Use correct printer driver settings.
Check if you have selected the correct port settings in the printer driver.
Are the port settings correct?
Step 11 Check the installed printer driver.
Go to step 12. Install the correct printer driver.
Is the correct printer driver installed?
The problem is solved. Contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Is the printer working?

The problem is solved. Go to step 2.
Press the Sleep button on the printer control panel.
Does Ready appear on the printer display?
The problem is solved. Turn off the printer, and then contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Do Please wait and Ready appear on the printer display?
The problem is solved. Go to step 2.
Turn off the printer, then wait for about 10 seconds, and then turn on the printer.
Does the internal option operate correctly?
Go to step 3. Connect the internal option to the controller board.
Check if the internal option is properly installed in the controller board.
a Turn off the printer using the power switch, and then unplug the power
cord from the electrical outlet. b Make sure the internal option is installed in the appropriate connector
in the controller board. c Connect the power cord to the printer, then to a properly grounded
electrical outlet, and then turn on the printer.
Is the internal option properly installed in the controller board?
Go to step 4. Reinstall the internal option.
Print a menu settings page, and then check to see if the internal option is listed in the Installed Features list.
Is the internal option listed in the menu settings page?

The problem is solved. Contact customer support.
a Check if the internal option is selected.
It may be necessary to manually add the internal option in the printer driver to make it available for print jobs. For more information, see “Updating available options in the printer driver” on page 29. b Resend the print job.
Does the internal option operate correctly?
The problem is solved. Go to step 2.
a Open the tray and do one or more of the following:
Is the tray working?
The problem is solved. Go to step 3.
a Turn off the printer, then wait about 10 seconds, and then turn the
printer back on. b Resend the print job.
Is the tray working?
Go to step 4. Reinstall the tray. For more information, see the setup documentation that came with the tray.
Check if the tray is installed.
Print a menu settings page, and then check if the tray is listed in the Installed Options list.
Is the tray listed in the menu settings page?
Go to step 5. Manually add the tray in the printer driver.
Check if the tray is available in the printer driver.
Is the tray available in the printer driver?

The problem is solved. Contact customer support.
Check if the option is selected.
a From the application you are using, select the option. For Mac OS X
version 9 users, make sure the printer is set up in Chooser. b Resend the print job.
Is the tray working?
Go to step 2. Check if you have a supported ISP.
Make sure the Internal Solutions Port (ISP) is installed.
a Install the ISP. For more information, see “Installing an Internal
Solutions Port” on page 16. b Print a menu settings page, and then check if the ISP is listed in the
Installed Options list.
Is the ISP listed in the Installed Options list?
The problem is solved. Contact customer support.
Check the cable and the ISP connection.
a Use the correct cable, and then make sure it is securely connected to
the ISP. b Check if the ISP solution interface cable is securely connected into the
receptacle of the controller board.
Does the Internal Solutions Port operate correctly?
Go to step 2. Check if you have a supported USB or parallel interface card.
Make sure the USB or parallel interface card is installed.
a Install the USB or parallel interface card. For more information, see
“Installing an Internal Solutions Port” on page 16. b Print a menu settings page, and then check if the USB or parallel
interface card is listed in the Installed Options list.
Is the USB or parallel interface card listed in the Installed Options list?

Contact customer support.
Connect the cable to the USB or parallel interface card connector.
Check if you are using the correct cable and if it is connected securely to the USB or parallel interface card.
Is the correct cable securely connected to the USB or parallel interface card?
Go to step 2. The problem is solved.
a Pull out the tray, and then do one or more of the following:
If jam recovery is enabled, then the print jobs will reprint automatically.
Do paper jams still occur frequently?
Go to step 3. The problem is solved.
a Load paper from a fresh package.
Do paper jams still occur frequently?
Contact customer support.
The problem is solved.
a Review the tips on avoiding jams. For more information, see “Avoiding
jams” on page 181. b Follow the recommendations, and then resend the print job.
Do paper jams still occur frequently?

a Do either of the following:
Contact customer support.
The problem is solved.
or Done.
the jam, press OK > . b Follow the instructions on the printer display.
Does the paper jam message remain?
a Turn on jam recovery.
The problem is solved. Contact customer support.
1 From the printer control panel, navigate to:
Settings > General Settings > Print Recovery > Jam Recovery 2 Select On or Auto.
3 Depending on your printer model, press or touch Submit. b Resend the pages that did not print.
Were the jammed pages reprinted?
Multiple‑language PDF files do not print
The problem is solved. Go to step 2.
a Check if the print options for the PDF output are set to embed all fonts. b Generate a new PDF file, and then resend the print job.
Do the files print?
The problem is solved. Contact customer support.
a Open the document you want to print in Adobe Acrobat. b Click File > Print > Advanced > Print As Image > OK > OK.
Do the files print?

Go to step 2. Insert the flash drive into the front USB slot.
Check if the flash drive is inserted into the front USB slot.
Is the flash drive inserted into the front USB slot?
Step 2 Check if the printer is busy.
Wait until the printer is ready, then view the held jobs list, and then print the documents.
Go to step 3.
Is there an error message on the display?
Clear the message. Go to step 4.
Check for an error message on the display.
Does the printer require attention?
Go to step 5. Use a supported flash drive.
Check if the flash drive is supported.
For more information regarding tested and approved USB flash memory devices, see “Supported flash drives and file types” on page 94.
Is the flash drive supported?
Step 5 Check if the USB slot is disabled by the system support person.
Contact your system support person.
Contact customer support.
Is the USB slot disabled?
The problem is solved. Go to step 2.
a From the document you are trying to print, open the Print dialog and
check if you have selected the correct printer.
Do the jobs print?

The problem is solved. Go to step 3.
a Check if the printer is plugged in and turned on, and if Ready appears
on the printer display. b Resend the print job.
Do the jobs print?
The problem is solved. Go to step 4.
If an error message appears on the printer display, then clear the message.
Do the jobs print?
The problem is solved. Go to step 5.
a Check if the ports (USB, serial, or Ethernet) are working and if the
cables are securely connected to the computer and the printer.
Do the jobs print?
The problem is solved. Go to step 6.
a Turn off the printer, then wait for about 10 seconds, and then turn the
printer back on. b Resend the print job.
Do the jobs print?
The problem is solved. Contact customer support.
a Remove, and then reinstall the printer software. For more
information, see “Installing the printer software” on page 28.
Do the jobs print?

Go to step 2. Select one of the Print and Hold options, and then resend the print job. For more information, see “Printing confidential and other held jobs” on page 95.
Open the held jobs folder on the printer display, and then verify that your print job is listed.
Is your print job listed in the held jobs folder?
The problem is solved. Go to step 3.
The print job may contain a formatting error or invalid data.
If you are printing from the Internet, then the printer may be reading multiple job titles as duplicates and deleting all jobs except the first one.
a Open the Print Properties folder. b From the Print and Hold dialog, select the “Keep duplicate documents”
check box. c Enter a PIN number.
Save each print job, name each job differently, and then send the individual jobs to the printer.
Does the job print?
The problem is solved. Add additional printer memory.
Free up additional printer memory by deleting some of the held jobs.
Does the job print?

The problem is solved. Go to step 2.
Change the environmental settings of the printer.
a From the printer control panel, navigate to:
Settings > General Settings b Select Eco‑Mode or Quiet Mode, and then select Off.
Did the job print?
The problem is solved. Go to step 3.
Reduce the number and size of fonts, the number and complexity of images, and the number of pages in the print job, and then resend the job
Did the job print?
The problem is solved. Go to step 4.
a Remove held jobs stored in the printer memory. b Resend the print job.
Did the job print?
The problem is solved. Go to step 5.
a Disable the Page Protect feature.
From the printer control panel, navigate to: Settings > General Settings > Print Recovery > Page Protect > Off b Resend the print job.
Did the job print?
The problem is solved. Contact customer support.
Install additional printer memory, and then resend the print job.
Did the job print?
The problem is solved. Go to step 2.
a Check if you are printing on paper that is supported by the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?

The problem is solved. Go to step 3.
a From the Paper menu on the printer control panel, set the paper size
and type to match the paper loaded in the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 4.
a Depending on your operating system, open Printing Preferences or
the Print dialog, and then specify the paper type. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Contact customer support.
a Check if the trays are not linked. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
Deactivate Hex Trace mode.
Go to step 2.
Make sure the printer is not in Hex Trace mode.
Is the printer in Hex Trace mode?
Contact customer support.
The problem is solved.
a From the printer control panel, select Standard Network or
Network [x], and then set SmartSwitch to On. b Resend the print job.
Do incorrect characters print?

a From the printer control panel, set the paper size and type in the Paper
The problem is solved. Contact customer support.
menu to match the paper loaded in the trays to be linked.
Do the trays link correctly?
The problem is solved. Go to step 2.
a From the Finishing menu on the printer control panel, set Collate to
(1,2,3) (1,2,3). b Resend the print job.
Did the job print and collate correctly?
The problem is solved. Go to step 3.
a From the printer software, set Collate to (1,2,3) (1,2,3).
Did the job print and collate correctly?
The problem is solved. Contact customer support.
Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Did the job print and collate correctly?
Step 1 Adjust the print timeout settings.
The problem is solved. Go to step 2.
a From the printer control panel, navigate to:
Settings > General Settings > Timeouts > Print Timeout b Select a higher setting and then, depending on your printer model,
select or Submit. c Resend the print job.
Did the file print correctly?


a Check the original file for manual page breaks. b Resend the print job.

Go to step 2. Select a font that is supported by the printer.
a Print a font sample list to check if the fonts you are using are supported
Menus > Reports > Print Fonts 2 Select PCL Fonts or PostScript Fonts. b Resend the print job.
Are you using fonts that are supported by the printer?
Step 2 Check if the fonts installed on the computer are supported by the printer.
Are the fonts installed on the computer supported by the printer?
ABCDE ABCDE ABCDE
Troubleshooting 218 · Leading edge · Trailing edge

Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the paper loaded. b Resend the print job.
Is the page or image clipped?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Do the paper size and type match the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.
Is the page or image clipped?
Contact customer support.
The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge. 2 Remove the imaging unit.
Is the page or image clipped?
ABCD ABCD ABCD ABCD


Go to step 2. Load paper with the correct paper type and weight in the tray.
Load paper with the correct paper type and weight in the tray.
Is paper with the correct paper type and weight loaded in the tray?
Go to step 3. Change the paper loaded in the tray to match the paper type and weight specified in the tray settings.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Is the tray set to the type and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do shadow images still appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do shadow images still appear on prints?

a From the Quality Menu on the printer control panel, decrease the

The problem is solved. Go to step 3.
Reinstall the imaging unit and the toner cartridge.
a Remove the toner cartridge. b Remove the imaging unit.
Did the gray background disappear from the prints?
The problem is solved. Contact customer support.
Replace the imaging unit, and then resend the print job.
Did the gray background disappear from the prints?
ABCD ABCD ABCD
The problem is solved. Go to step 2.
a Move the width and length guides in the tray to the correct positions
for the paper size loaded. b Resend the print job.
Are the margins correct?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size in the Paper menu to match the paper loaded in the tray.
Does the paper size match the paper loaded in the tray?

The problem is solved. Contact customer support.
a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.
Are the margins correct?
Go to step 2. Adjust the width and length guides.
Move the width and length guides in the tray to the correct positions for the size of the paper loaded.
Are the width and length guides positioned correctly?
Go to step 3. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the paper still curled?
Go to step 5. The problem is solved.
a Remove the paper from the tray, and then turn it over. b Resend the print job.
Is the paper still curled?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Is the paper still curled?

) ) ABCDE
ABCDE ABCDE
Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded in the tray. b Resend the print job.
Do print irregularities still appear?
Go to step 3. Specify the paper size and type from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Do the printer settings match the type and weight of the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do print irregularities still appear?
From the printer control panel, set the paper texture in the Paper menu to match the paper loaded in the tray.
Go to step 5.
Check if the paper loaded in the tray has texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Do print irregularities still appear?
Contact customer support at http://support.lexmar k.com or your service representative.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do print irregularities still appear?

Go to step 2. 1 Check if the distance between the defects equal to 80 mm (3.15 in.) 2 Take note of the distance, and then contact customer support at http://support.le xmark.com or your service representative.
Measure the distance between the defects.
Check for a distance between the defects that equals:
Is the distance between defects equal to one of the listed measurements?
Contact customer support at http://support.lexma rk.com or your service representative.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do the repeating defects still appear?
Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, reduce the toner
darkness.
Is the print still too dark?

Go to step 3. Do one or more of the following:
a From the printer control panel, set the paper type, texture and weight
in the Paper menu to match the paper loaded in the tray. b Resend the print job.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type, texture
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too dark?
From the printer control panel, change the texture settings in the Paper Texture menu to match the paper you are printing on.
Go to step 5.
Check if the paper loaded in the tray has texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too dark?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the print still too dark?

Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, increase the toner
darkness.
Is the print still too light?
Go to step 3. Change the paper type, texture, and weight to match the paper loaded in the tray.
From the printer control panel, set the paper type, texture, and weight in the Paper menu to match the paper loaded in the tray.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too light?
From the printer control panel, change the texture settings in the Paper Texture menu to match the paper you are printing on.
Go to step 5.
Make sure that the paper has no texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too light?

Go to step 7. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Is the print still too light?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the print still too light?
Go to step 2. The problem is solved.
a Check if there is packing material left on the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Check if the packing material is properly removed from the imaging unit.
Is the printer still printing blank pages?

Go to step 3. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Is the printer still printing blank pages?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the printer still printing blank pages?
) ) ABCDE
ABCDE ABCDE
Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded. b Resend the print job.
Is the print still skewed?
Contact customer support.
The problem is solved.
a Check if you are printing on a paper that is supported by the tray. b Resend the print job.
Is the print still skewed?

Go to step 2. The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge, and then the imaging unit.
Is the printer printing solid black pages?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the printer printing solid black pages?
Go to step 2. Set the paper type to Transparency.
From the printer control panel, set the paper type in the Paper menu to match the paper loaded in the tray.
Is the paper type for the tray set to Transparency?
Contact customer support.
The problem is solved.
a Check if you are using a recommended type of transparency. b Resend the print job.
Is the print quality still poor?

ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the tray or feeder from
Printing Preferences or the Print dialog. b Resend the print job.
Do streaked horizontal lines appear on prints?
Go to step 3. Change the paper type and weight to match the paper loaded in the tray.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked horizontal lines appear on prints?
Go to step 5. The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge, and then the imaging unit.
Do streaked horizontal lines appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do streaked horizontal lines appear on prints?

ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do streaked vertical lines appear on prints?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper texture, type, and weight in the Paper menu to match the paper loaded in the tray.
Do the paper texture, type, and weight match the paper in the tray?
Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked vertical lines appear on prints?
Go to step 5. The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge, and then the imaging unit.
Do streaked vertical lines appear on prints?


Contact customer support at http://support.lexmar k.com or your service representative.
Replace the imaging unit, and then resend the print job.

a Make sure your software program is using a correct fill pattern. b Resend the print job.
a Load the specified tray or feeder with a recommended type of paper. b Resend the print job.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Replace the imaging unit, and then resend the print job.
Troubleshooting 232

Go to step 2. The problem is solved.
a Make sure your software program is using a correct fill pattern. b Resend the print job.
Do vertical voids appear on prints?
Go to step 3. The problem is solved.
a From the printer control panel, set the paper type and weight in the
Paper menu to match the paper loaded in the tray. b Resend the print job.
Do vertical voids appear on prints?
Step 3 Check if you are using a recommended type of paper.
Go to step 4. The problem is solved.
a Load the indicated tray or feeder with a recommended type of paper. b Resend the print job.
Do vertical voids appear on prints?
Contact customer support.
The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Do vertical voids appear on prints?


Replace the imaging unit, and then resend the print job.

a Remove, and then install the imaging unit. b Resend the print job.
Contact customer support at http://support.lexmar k.com or your service representative.
Replace the imaging unit, and then resend the print job.
ABC DEF
Troubleshooting 234 · Leading edge · Trailing edge

Go to step 2. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
From the Paper menu on the printer control panel, check the paper type and weight.
Do the paper type and texture match the paper loaded in the tray?
From the Paper menu on the printer control panel, set the paper texture.
Contact customer support.
Check if you are printing on paper with texture or rough finishes.
Are you printing on textured or rough paper?
Replace the imaging unit, and then resend the print job.
Contact customer support.
The problem is solved.
Is the print density uneven?

This troubleshooting step applies only to touch‑screen printer models.
Go to step 2. Contact customer support.
Check the system log for relevant details.
a Open a Web browser, and then type the printer IP address in the
address field.
If you do not know the IP address of the printer, then you can:
c From the Filter menu, select an application status. d From the Application menu, select an application, and then click
Submit.
Does an error message appear in the log?
Step 2 Resolve the error.
The problem is solved. Contact customer support.
Is the application working now?
The problem is solved. Go to step 2.
a Turn on the printer. b Open a Web browser, and then type the printer IP address.
c Press Enter.
Does the Embedded Web Server open?

The problem is solved. Go to step 3.
Make sure the printer IP address is correct.
a View the printer IP address:
Does the Embedded Web Server open?
Step 3 Check if the network is working.
The problem is solved. Go to step 4.
a Print a network setup page. b Check the first section of the network setup page and confirm that the
status is Connected.
Does the Embedded Web Server open?
The problem is solved. Go to step 5.
Check if the cable connections to the printer and print server are secure.
a Connect the cables properly. For more information, see the setup
documentation that came with the printer. b Open a Web browser, and then type the printer IP address.
c Press Enter.
Does the Embedded Web Server open?
The problem is solved. Contact your system support person.
Temporarily disable the Web proxy servers.
Proxy servers may block or restrict you from accessing certain Web sites including the Embedded Web Server.
Does the Embedded Web Server open?

When you contact customer support, describe the problem you are experiencing, the message on the printer display, and the troubleshooting steps you have already taken to find a solution.
You need to know your printer model type and serial number. For more information, see the label on the inside top front cover or at the back of the printer. The serial number is also listed on the menu settings page.
Lexmark has various ways to help you solve your printing problem. Visit the Lexmark Web site at http://support.lexmark.com, and then select one of the following:
Tech Library You can browse our library of manuals, support documentation, drivers, and other downloads to help you
solve common problems.
E-mail You can send an e-mail to the Lexmark team, describing your problem. A service representative will respond and provide you with information to solve your problem.
Live chat You can chat directly with a service representative. They can work with you to solve your printer problem or provide assistance through Assisted Service where the service representative can remotely connect to your computer through the Internet to troubleshoot problems, install updates, or complete other tasks to help you successfully use your Lexmark product.
Telephone support is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, visit the Lexmark Web site at http://support.lexmark.com.
Troubleshooting 238

Product name:
Lexmark MS510dn, MS610dn, and MS610de
Machine type:
Model(s):
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
© 2013 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
630, 635, 646 · May 2013

Lexmark, Lexmark with diamond design, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
PrintCryption is a trademark of Lexmark International, Inc.
Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
The following terms are trademarks or registered trademarks of these companies:

CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Agfa Corporation

Univers Linotype-Hell AG and/or its subsidiaries
All other trademarks are the property of their respective owners.
AirPrint and the AirPrint logo are trademarks of Apple, Inc.
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232–3000
Wireless‑equipped models contain the following modular component(s):
Lexmark Regulatory Type/Model LEX-M01-005; FCC ID:IYLLEXM01005; IC:2376A-M01005
All licensing notices associated with this product can be viewed from the root directory of the installation software CD.

The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Printing 55 dBA (simplex); 54 dBA (duplex)
Values are subject to change. See www.lexmark.com for current values.
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products.
If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.
According to Article 15 of the Waste Disposal Act in the announcement of Taiwan EPA, the producing or the importing manufacturer is responsible for recycling, clearance, and disposal of dry cell batteries, batteries packaged with products and sold, given, and promoted with products to consumers may be labeled with the recycling mark with the remark "please recycle waste batteries" on the product package, the label, or the product manual. Enclosed please find the waste dry cell batteries recycle logo with the remark. Please give the waste dry cell batteries to a company who has
Ready N/A

the waste dry cell batteries recycle logo and provides the recycle service in order to have the appropriate process for the waste dry cell batteries.
This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching the metal frame of the printer.
Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
Ambient operating temperature 15.6 to 32.2°C (60 to 90°F)
Shipping temperature -40 to 43.3°C (-40 to 110°F)
Storage temperature and relative humidity 1 to 35°C (34 to 95°F)
8 to 80% RH
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, Chapter I, Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1.

Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 7 milliwatt gallium arsenide laser operating in the wavelength of 655-675 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
A laser notice label may be affixed to this printer as shown:
Opasnost - Nevidljivo lasersko zračenje kada su kasete uklonjene i poništena sigurnosna veza. Izbjegavati izlaganje zracima.
NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, ze zařízení je vysíláno neviditelné laserové záření. Nevystavujte se působení laserového paprsku.
FARE - Usynlig laserstråling, når patroner fjernes, og spærreanordningen er slået fra. Undgå at blive udsat for laserstrålen. GEVAAR - Onzichtbare laserstraling wanneer cartridges worden verwijderd en een vergrendeling wordt genegeerd. Voorkom blootstelling aan de laser.
VAARA - Näkymätöntä lasersäteilyä on varottava, kun värikasetit on poistettu ja lukitus on auki. Vältä lasersäteelle altistumista.
VESZÉLY – Nem látható lézersugárzás fordulhat elő a patronok eltávolításakor és a zárószerkezet felbontásakor. Kerülje a lézersugárnak való kitettséget.
FARE – Usynlig laserstråling når kassettene tas ut og sperren er satt ut av spill. Unngå eksponering for laserstrålen. NIEBEZPIECZEŃSTWO - niewidzialne promieniowanie laserowe podczas usuwania kaset i blokady. Należy unikać naświetlenia promieniem lasera.
ОПАСНО! Невидимое лазерное излучение при извлеченных картриджах и снятии блокировки. Избегайте воздействия лазерных лучей.
Pozor – Nebezpečenstvo neviditeľného laserového žiarenia pri odobratých kazetách a odblokovanej poistke. Nevystavujte sa lúčom.
危险 - 当移除碳粉盒及互锁失效时会产生看不见的激光辐射,请避免暴露在激光光束下。
危険 - カートリッジが取り外され、内部ロックが無効になると、見えないレーザー光が放射されます。 このレーザー光に当たらないようにしてください。
Power consumption
Product power consumption
The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs. 600 (MS510dn); 640 (MS610dn, MS610de)
Copy The product is generating hard‑copy output from hard‑copy original documents.
Scan The product is scanning hard‑copy documents. NA
Ready The product is waiting for a print job. 10 (MS510 and MS610dn); 12 (MS610de)
Sleep Mode The product is in a high‑level energy‑saving mode. 5 (MS510 and MS610dn); 5.5 (MS610de)

Mode Description Power consumption (Watts)
Hibernate The product is in a low‑level energy‑saving mode. 1
Off The product is plugged into an electrical outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.
This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 30
By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 120 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
This product is designed with an ultra‑low power operating mode called Hibernate mode. When operating in Hibernate Mode, all other systems and devices are powered down safely.
The Hibernate mode can be entered in any of the following methods:
Factory default Hibernate Timeout for this product in all countries or regions except for EU countries and Switzerland
Factory default value for this product in EU countries or regions and Switzerland 3 days
The amount of time the printer waits after a job is printed before it enters Hibernate mode can be modified between one hour and one month.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the electrical outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
Disabled

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
この装置は、クラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この 装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをしてください。
VCCI-B
European Community (EC) directives conformity
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and the ecodesign of energy- related products.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
This section contains the following regulatory information pertaining to wireless products that contain transmitters, for example, but not limited to, wireless network cards or proximity card readers.
The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.

This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb
The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.
Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement.
Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada.
En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.
Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur et loin des fenêtres afin de garantir une protection optimale.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc-sc.gc.ca/rpb
Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme aux spécifications techniques d'Industry Canada.
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, radio equipment and telecommunications terminal equipment and on the ecodesign of energy-related products.

Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
Products equipped with 2.4GHz Wireless LAN option are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment and on the ecodesign of energy-related products.
Compliance is indicated by the CE marking.
Operation is allowed in all EU and EFTA countries, but is restricted to indoor use only.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product may be used in the countries indicated in the table below.

AT BE BG CH CY CZ DE DK EE
EL ES FI FR HR HU IE IS IT
LI LT LU LV MT NL NO PL PT
Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.
Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.
Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.
Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.
Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.
Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.
Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky
príslušné ustanovenia smernice 1999/5/ES.
Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
STATEMENT OF LIMITED WARRANTY FOR LEXMARK LASER PRINTERS, LEXMARK LED PRINTERS, AND LEXMARK MULTIFUNCTION LASER PRINTERS
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country- specific warranty information that came with your product.

This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Transfer/Transport Units, Paper Feed items, if any, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
As part of your warranty service and/or replacement, Lexmark may update the firmware in your printer to the latest version. Firmware updates may modify printer settings and cause counterfeit and/or unauthorized products, supplies, parts, materials (such as toners and inks), software, or interfaces to stop working. Authorized use of genuine Lexmark products will not be impacted.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.

Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.

The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Elliptic Curve Cryptography (ECC) Cipher Suites for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Elliptic Curve Cipher Suites with SHA-256/382 and AES Galois Counter Mode (GCM) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Suite B Profile for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Addition of the Camellia Cipher Suites to Transport Layer Security (TLS) implemented in the product or service.
The use of certain patents in this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for AES-CCM ECC Cipher Suites for TLS implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for IKE and IKEv2 Authentication Using the Eliptic Curve Digital Signature Algorithm (ECDSA) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Suite B Cryptographic Suites for IPSec implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Algorithms for Internet Key Exchange version 1 (IKEv1) implemented in the product or service.







Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.