EN
Lexmark logo
Official user manual

Lexmark M412

312 pages·3.8 MB·Printer·PDF·ENDEFRITNLJA
Lexmark M412
Table of Contents 202 sections Introduction · About This Book · Other Information · Online Documents · … ShowHide
Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 1 of the Lexmark M412 user manual — M410 M412
Page 1 · click to enlarge
Page 1

M410 M412

Lexmark M412 — M410 M412 diagram (page 1)
Fig. 1
Page 2 of the Lexmark M412 user manual
Page 2 · click to enlarge
Page 2
EditionMay 2000

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.

A form for the reader’s comments is provided at the back of this publication. If the form has been removed, comments may be addressed to Lexmark International, Inc., Department F95/035-3, 740 West New Circle Road, Lexington, Kentucky 40550, U.S.A. In the United Kingdom and Eire, send to Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. You can purchase additional copies of publications related to this product by calling 1-800-553-9727. In the United Kingdom and Eire, call 0628-481500. In other countries, contact your point of purchase.

References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.

© Copyright 1999, 2000 Lexmark International, Inc. All rights reserved.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS This software and documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 and in applicable FAR provisions: Lexmark International, Inc., Lexington, KY 40550.

Page 3 of the Lexmark M412 user manual — Table of contents
Page 3 · click to enlarge
Page 3

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 4 of the Lexmark M412 user manual — Table of contents
Page 4 · click to enlarge
Page 4

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 5 of the Lexmark M412 user manual — Table of contents
Page 5 · click to enlarge
Page 5

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 6 of the Lexmark M412 user manual — Table of contents
Page 6 · click to enlarge
Page 6

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 7 of the Lexmark M412 user manual — Table of contents
Page 7 · click to enlarge
Page 7

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 8 of the Lexmark M412 user manual — Table of contents
Page 8 · click to enlarge
Page 8

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 9 of the Lexmark M412 user manual — ix Introduction
Page 9 · click to enlarge
Page 9

Introduction

About This Book This User’s Guide contains information about the Lexmark Optra M410 and M412 laser printers. It provides setup instructions for the printer and printer options as well as information about loading print material, changing printer settings, replacing printer supplies, and trouble- shooting problems.

Keep this book in a handy place and use it as a reference when you have a question about printer function or if you encounter a printing problem.

It may be helpful for you to recognize the following con- ventions used throughout this book:

  • Notes, warnings, and cautions appear in the left column for easy reference.
  • Operator panel buttons are printed in boldface type:

Press Go after changing a menu setting.

  • Messages, menu names, menu items, and menu settings that appear on the operator panel display are also printed in boldface type:

If Load Tray 1 appears on the operator panel dis- play, you must load print material in tray 1 and press Go before you can resume printing.

ix Introduction

Page 10 of the Lexmark M412 user manual — x Introduction
Page 10 · click to enlarge
Page 10

The Paper Source setting is available in the PAPER MENU.

Other Information In addition to this User’s Guide, Lexmark offers the follow- ing sources of information about your printer and other Lexmark products and services.

Online Documents The Drivers, MarkVision and Utilities compact disc (CD) that comes with your printer contains several online docu- ments. Refer to the booklet that comes with the CD for launching instructions. Once you launch the CD, click View Documentation to display a list of available docu- ments.

The CD includes:

The MarkVision printer utility information, which pro- vides step-by-step instructions for installing MarkVision for Windows 95/98/2000, Windows NT 4.0, Macintosh, and OS/2 on several different networks. It also describes some of the most popular MarkVision features.

  • Documents which provide general information about setting up an optional print server after installing it in your printer.
  • Documents which describe font options and available resources.
  • A Card Stock & Label Guide which provides detailed information about selecting print material appropriate for your printer.
  • A Technical Reference which includes information about printer languages and commands, interface specification, and printer memory management.

x Introduction

Page 11 of the Lexmark M412 user manual — xi Trademarks
Page 11 · click to enlarge
Page 11

Trademarks

Lexmark, Lexmark with diamond design, MarkNet, MarkVision, and Optra are trademarks of Lexmark Inter- national, Inc., registered in the United States and/or other countries.

MarkTrack, Optra Forms, and PictureGrade are trade- marks of Lexmark International, Inc.

Operation ReSource is a service mark of Lexmark Interna- tional, Inc.

PCL® is a registered trademark of the Hewlett-Packard Company. PCL 6 is Hewlett-Packard Company’s designa- tions of a set of printer commands (language) and func- tions included in its printer products. This printer is intended to be compatible with the PCL 6 language. This means the printer recognizes PCL 6 commands used in various application programs, and that the printer emu- lates the functions corresponding to the commands.

PostScript® is a registered trademark of Adobe Systems Incorporated. PostScript 3 is Adobe Systems’ designation of a set of printer commands (language), fonts, and func- tions included in its software products. This printer is intended to be compatible with the PostScript 3 language. This means the printer recognizes PostScript 3 commands used in various application programs, and that the printer emulates the functions corresponding to the commands.

Details relating to compatibility are included in the Technical Reference.

xi Trademarks

Page 12 of the Lexmark M412 user manual — xii Trademarks
Page 12 · click to enlarge
Page 12

The following terms are trademarks or registered trade- marks of these companies.

Albertus The Monotype Corporation plc.

Antique Olive Monsieur Marcel OLIVE

Arial The Monotype Corporation plc.

CG Omega A product of Bayer Corporation

CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Bayer Corporation

Helvetica Linotype-Hell AG and/or its subsidiaries

ITC Bookman International Typeface Corporation

ITC Zapf Chancery International Typeface Corporation

LocalTalk Apple Computer, Inc.

Macintosh Apple Computer, Inc.

Marigold AlphaOmega Typography, Inc.

Palatino Linotype-Hell AG and/or its subsidiaries

Pantone Pantone, Inc.

PostScript Adobe Systems Incorporated

Times New Roman The Monotype Corporation plc.

TrueType Apple Computer, Inc.

Univers Linotype-Hell AG and/or its subsidiaries

Other trademarks are the property of their respective owners.

xii Trademarks

Intellifont Bayer Corporation · Wingdings Microsoft Corporation

Page 13 of the Lexmark M412 user manual — CD
Page 13 · click to enlarge
Page 13
Lexmark M412 — Setting Up YourPrinter diagram (page 13)
Fig. 2 · Setting Up YourPrinter

Complete the following sections to set up your Lexmark™ Optra™M410 and M412 printers.

Unpacking Your Printer

1 Remove the printer and all items from the packag- ing carton.

Save the carton and packing materials in case you need to repack the printer for service or storage.

Lexmark M412 — Unpacking Your Printer diagram (page 13)
Fig. 3 · Unpacking Your Printer

2 Make sure you have the items shown.

If any items are missing, contact the place where you bought your printer.

3 Place the printer on a flat, sturdy surface in a well- ventilated area.

Allow at least 304.8 mm (12 in.) of clearance on all sides of the printer. Since you may want to install the optional 500-sheet drawer, leave at least 129.6 mm (5.1 in.) clearance above the printer. Leave enough space in front of the printer to allow for easy paper access.

CD

1 Unpacking Your Printer

Plastic Bracket

Page 14 of the Lexmark M412 user manual — 2 Chapter 1: Setting Up Your Printer
Page 14 · click to enlarge
Page 14

Use the following information to help determine where to place your printer.

Lexmark M412 — Removing Print Cartridge Packaging diagram (page 14)
Fig. 4 · Removing Print Cartridge Packaging

Do not place the printer:

– In direct sunlight. – Near heat sources or air conditioners. – In dusty or dirty environments.

Removing Print

To remove the print cartridge packaging:

Lexmark M412 — Removing Print diagram (page 14)
Fig. 5 · Removing Print

1 Push the upper release latch to release the upper front door.

2 Chapter 1: Setting Up Your Printer

Page 15 of the Lexmark M412 user manual — 3 Removing Print Cartridge Packaging
Page 15 · click to enlarge
Page 15

2 Raise the upper front door.

Lexmark M412 — Removing Print Cartridge Packaging diagram (page 15)
Fig. 6 · Removing Print Cartridge Packaging

It remains in place.

3 Grasp the print cartridge by the handgrip.

Lexmark M412 — Removing Print Cartridge Packaging diagram (page 15)
Fig. 7 · Removing Print Cartridge Packaging

3 Removing Print Cartridge Packaging

Page 16 of the Lexmark M412 user manual — 4 Chapter 1: Setting Up Your Printer
Page 16 · click to enlarge
Page 16

4 Lift the print cartridge up and pull out.

Lexmark M412 — Removing Print Cartridge Packaging diagram (page 16)
Fig. 8 · Removing Print Cartridge Packaging

5 Pull up on each end of the plastic piece and then remove the packaging material.

Lexmark M412 — Removing Print Cartridge Packaging diagram (page 16)
Fig. 9 · Removing Print Cartridge Packaging

Discard all packaging material: the plastic piece, the foam, and the paper connected to the foam.

6 Continue with “Installing the Print Cartridge” on page 5.

4 Chapter 1: Setting Up Your Printer

Page 17 of the Lexmark M412 user manual — 5 Installing the Print Cartridge
Page 17 · click to enlarge
Page 17

Installing the Print Cartridge

To prepare the print cartridge for printing:

1 Gently shake the print cartridge side-to-side to distribute the toner.

Lexmark M412 — Installing the Print Cartridge diagram (page 17)
Fig. 10 · Installing the Print Cartridge

2 Insert the print cartridge:

Lexmark M412 — 2 Insert the print cartridge: diagram (page 17)
Fig. 11 · 2 Insert the print cartridge:

a Align the tabs located on each side of the print

cartridge with the slots on either side of the print cartridge cradle as shown.

Use the colored arrows inside the printer for placement.

5 Installing the Print Cartridge

Page 18 of the Lexmark M412 user manual — 6 Chapter 1: Setting Up Your Printer
Page 18 · click to enlarge
Page 18

b Slide the print cartridge straight back into the

Lexmark M412 — b Slide the print cartridge straight back into the diagram (page 18)
Fig. 12 · b Slide the print cartridge straight back into the

printer until it snaps into place.

3 Close the upper front door.

You cannot close the door completely if the print cartridge is not installed correctly.

Loading the

Your printer has one standard 250-sheet input tray that holds five paper sizes. For information on the different sizes and types of print material you can use with your printer, see “Using Print Materials” on page 115.

Standard Input Tray

For information on loading envelopes and other types of print material, see “Multipurpose Feeder” on page 139.

Lexmark M412 — Standard Input Tray diagram (page 18)
Fig. 13 · Standard Input Tray

To load paper:

1 Pull the input tray straight out of the printer.

Remove the input tray completely from the printer.

6 Chapter 1: Setting Up Your Printer

Page 19 of the Lexmark M412 user manual — 7 Loading the Standard Input Tray
Page 19 · click to enlarge
Page 19

2 Press down on the metal plate until it locks into place.

Lexmark M412 — Loading the Standard InputTray diagram (page 19)
Fig. 14 · Loading the Standard InputTray

The metal plate remains stationary on the inside bottom of the input tray.

3 Press down on the length guide tab with one hand, and with the other hand slide the length guide to the correct position for the size paper you are loading.

Paper Size Indicators Length Guide

Lexmark M412 — Loading the Standard InputTray diagram (page 19)
Fig. 15 · Loading the Standard InputTray

Use the paper size indicators to adjust the length guide for one of the following five paper sizes: A4, B5, LTR (Letter), LGL (Legal), and EXEC (Execu- tive).

7 Loading the Standard Input Tray

Page 20 of the Lexmark M412 user manual — 8 Chapter 1: Setting Up Your Printer
Page 20 · click to enlarge
Page 20

4 Press down on the width guide tab and slide the width guide to the far right side of the input tray as shown.

Lexmark M412 — Loading the Standard InputTray diagram (page 20)
Fig. 16 · Loading the Standard InputTray

5 Flex the sheets back and forth to loosen them, then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

Lexmark M412 — Loading the Standard InputTray diagram (page 20)
Fig. 17 · Loading the Standard InputTray

For this setup, load letter-size paper.

8 Chapter 1: Setting Up Your Printer

Width Guide Tab

Page 21 of the Lexmark M412 user manual — 9 Loading the Standard Input Tray
Page 21 · click to enlarge
Page 21

6 Place the paper against the left side of the input tray and insert it under the metal stop.

Lexmark M412 — Loading the Standard InputTray diagram (page 21)
Fig. 18 · Loading the Standard InputTray

Make sure the recommended print side is face down and the front edge is placed toward the front of the input tray.

For information on how to load letterhead, see “Printing on Letterhead” on page 135.

Lexmark M412 — Loading the Standard InputTray diagram (page 21)
Fig. 19 · Loading the Standard InputTray

7 Do not exceed the maximum stack height indi- cated by the line under the arrows.

9 Loading the Standard Input Tray

Page 22 of the Lexmark M412 user manual — 10 Chapter 1: Setting Up Your Printer
Page 22 · click to enlarge
Page 22

8 Push on the right side of the width guide to move it to the left until it lightly touches the edge of the paper.

Lexmark M412 — Loading the Standard InputTray diagram (page 22)
Fig. 20 · Loading the Standard InputTray
Lexmark M412 — Loading the Standard InputTray diagram (page 22)
Fig. 21 · Loading the Standard InputTray

9 Slide the input tray all the way into the printer until it snaps into place.

10 Chapter 1: Setting Up Your Printer

Width Guide

Page 23 of the Lexmark M412 user manual — 11 Installing the Paper Bail
Page 23 · click to enlarge
Page 23

Installing the

The paper bail helps prevent offset bin stacking by guid- ing print material into the standard output bin.

Paper Bail

The paper bail consists of two parts: a plastic bracket already installed on the printer and a metal bail.

Complete the following steps to install the metal bail:

1 Locate the metal bail that comes with your printer.

2 Orient the metal bail as shown.

3 Place the tips of the metal bail into the holes located on either end of the plastic bracket as shown.

Metal Bail Plastic Bracket

Lexmark M412 — Paper Bail diagram (page 23)
Fig. 22 · Paper Bail

11 Installing the Paper Bail

Page 24 of the Lexmark M412 user manual — 12 Chapter 1: Setting Up Your Printer
Page 24 · click to enlarge
Page 24

Connecting Your

To print from your computer, you need to connect your printer to your computer with either a parallel interface cable or a Universal Serial Bus (USB) cable.

Printer to a

Computer

Using a Parallel Cable

Your printer uses an IEEE 1284-compliant parallel cable that supports bidirectional communication. We recom- mend Lexmark part number 1329605 (10 ft) or 1427498 (20 ft). If you use a cable other than an IEEE-com- pliant cable, you may not be able to access all of your printer functions.

1 Turn the printer power Off (O) and unplug the printer power cord from the electrical outlet.

2 Align and plug the parallel cable into the parallel connector as shown.

12 Chapter 1: Setting Up Your Printer

Parallel Cable · Parallel Connector

Page 25 of the Lexmark M412 user manual — 6 Continue with “Plugging the Printer In” on page 20. Clips
Page 25 · click to enlarge
Page 25

3 Push the clips at each end of the connector down into the notches on the plug as shown. The clips snap into the notches.

4 Connect the other end of the parallel cable to the back of your computer. Tighten the screws on the parallel cable to the computer.

5 Check the parallel cable connections to make sure they are completely secured.

6 Continue with “Plugging the Printer In” on page 20. Clips

13 Connecting Your Printer to a Computer

Page 26 of the Lexmark M412 user manual — 14 Chapter 1: Setting Up Your Printer
Page 26 · click to enlarge
Page 26

Using a USB Cable Your printer has one standard USB port located on the printer system board.

Complete the following steps to connect your printer using a USB cable.

For Windows 2000 users:

1 Make sure the computer and printer power are Off (O) and the printer power cord is unplugged from the electrical outlet.

2 Connect the USB cable to the port on the back of your computer.

3 Connect the other end of the cable to the USB port on the back of your printer.

Lexmark M412 — For Windows 2000 users: diagram (page 26)
Fig. 23 · For Windows 2000 users:

4 Turn on your computer and your printer.

5 When the Found New Hardware Wizard screen appears, select Cancel to close the wizard.

6 Insert the CD that came with your printer and select Start.

7 From the Start menu, select Run, then click Browse.

8 Click on the My Computer shortcut in the Browse window, double-click on the CD icon, and double- click on the Setup icon.

9 Click OK to start the printer driver installation program.

10 Follow the installation instructions in the printer drivers dialog box.

11 In the Print to the following port check box, select the USB port that best describes the order you’ve connected USB printers to your computer (for example, the first USB printer is USB001, the sec- ond USB002, and so on).

14 Chapter 1: Setting Up Your Printer

Page 27 of the Lexmark M412 user manual — 15 Connecting Your Printer to a Computer
Page 27 · click to enlarge
Page 27

12 In the Select a port for this printer check box, select the USB port that best describes the order you’ve connected USB printers to your com- puter (for example, the first USB printer is USB001, the second USB002, and so on).

13 When you finish, exit the setup program and remove the CD from your computer.

For Windows 98 users:

1 Make sure the printer power is Off (O) and the printer power cord is unplugged from the electri- cal outlet.

Lexmark M412 — For Windows 98 users: diagram (page 27)
Fig. 24 · For Windows 98 users:

2 Align and plug the USB cable into the USB port on the back of your printer as shown.

3 Connect the other end of the USB cable to the back of your computer.

4 Check the cable connections to make sure they are completely secured.

5 Follow the steps under “Plugging the Printer In” on page 20.

6 Follow the steps under “Turning the Printer Power On” on page 20.

7 Complete the following steps to setup the printer port and install the correct drivers.

When you turn the printer power On (|), the Add New Hardware Wizard screen appears on your com- puter.

a Click Next.

b Click the default to search for the best driver.

Click Next.

c Click to clear the check boxes for Floppy Disk or

CD-ROM.

15 Connecting Your Printer to a Computer

Page 28 of the Lexmark M412 user manual — 16 Chapter 1: Setting Up Your Printer
Page 28 · click to enlarge
Page 28

d Insert the compact disc (CD) that came with

your printer.

e Click Specify a location.

f Click Browse.

g Scroll down until you locate your CD-ROM

drive. Double-click to select it.

h Highlight the folder for WIN98USB and click

OK.

i Click Next.

A screen displays indicating the application is looking for this laser printer to verify the driver for the printer.

j Click Next.

Wait as the information processes. When the next screen appears that tells you the software is installed, click Finish. Complete the following to install the printer driver.

k Click Install Software.

l Click Printer Software.

The Choose your Installation Path screen displays.

m Select Install from this CD.

The License Agreement displays.

n Click Agree once you have read the agreement.

o Select Custom Install and click Next.

Printer Drivers is selected as the default on the next screen.

p Click Next.

q Scroll through the list of printers on the left of

the screen and click the check box to select Optra M410 or Optra M412.

16 Chapter 1: Setting Up Your Printer

Page 29 of the Lexmark M412 user manual — 17 Connecting Your Printer to a Computer
Page 29 · click to enlarge
Page 29

r Click the Add button.

The name of your printer moves to the box on the right of the screen.

s Click Next.

The Drivers tab screen displays.

t Highlight LPT1 in the top window of the screen for the PostScript language.

u Scroll to USB001 in the bottom window of the

screen and select it.

v Return to the top window of the screen and

select LPT1 for the PCL language.

w Scroll to USB001 in the bottom window of the

screen and select it.

x Click Finish Installation.

Wait as the information processes.

y Click Yes to restart Windows.

z Click OK.

17 Connecting Your Printer to a Computer

Page 30 of the Lexmark M412 user manual — 18 Chapter 1: Setting Up Your Printer
Page 30 · click to enlarge
Page 30

For Macintosh users:

1 Make sure the printer power is Off (O) and the printer power cord is unplugged from the electri- cal outlet.

2 Connect the end of the USB cable to the port on your computer.

Lexmark M412 — For Macintosh users: diagram (page 30)
Fig. 25 · For Macintosh users:

3 Align and plug the other end of the USB cable into the port on the back of your printer as shown.

4 Follow the steps under “Plugging the Printer In” on page 20.

5 Follow the steps under “Turning the Printer Power On” on page 20.

6 Launch the CD to install the necessary items. Instructions to launch the CD are in the CD booklet.

7 Restart the computer.

8 Open the Apples Extras folder.

9 Open the Apple LaserWriter Software folder.

10 Open the Desktop Printer Utility application.

11 The New Desktop Printer screen displays.

12 Select Printer (USB) from the list and click OK.

13 In the USB printer selection area, click Change.

The USB printer dialog box displays.

14 Select Optra M410 or Optra M412 and click OK.

The previous screen displays. Notice the new printer icon.

15 In the PostScript printer description (PPD) file, click Auto Setup.

Wait for the information to process.

18 Chapter 1: Setting Up Your Printer

Page 31 of the Lexmark M412 user manual — 19 Connecting Your Printer to a Computer
Page 31 · click to enlarge
Page 31

The previous screen displays. Notice the new printer icon.

16 Click Create.

A window appears for you to name the printer.

17 Type in the name of the printer or accept the default name.

18 Click Save.

19 Quit the Desktop Printer Utility application.

The printer icon displays on your Desktop.

20 Click the new desktop printer icon.

The Printing menu appears on the menu bar.

21 Scroll down in the Printing menu and select Set Default Printer.

A dark line appears around the printer in the printer icon to indicate it is selected as the default printer.

19 Connecting Your Printer to a Computer

Page 32 of the Lexmark M412 user manual — 20 Chapter 1: Setting Up Your Printer
Page 32 · click to enlarge
Page 32

Plugging the

1 Plug the printer power cord into the connector as shown.

Printer In

2 Plug the other end of the printer power cord into a properly grounded electrical outlet.

Lexmark M412 — Printer In diagram (page 32)
Fig. 26 · Printer In

3 Continue with “Turning the Printer Power On” on page 20.

Turning the Printer

Turn the printer power On (|).

Power On

If an error message displays, see “Understanding Printer Messages” on page 151 for more information.

Lexmark M412 — Power On diagram (page 32)
Fig. 27 · Power On

20 Chapter 1: Setting Up Your Printer

Page 33 of the Lexmark M412 user manual — 21 Printing the Menu Settings Page
Page 33 · click to enlarge
Page 33

Printing the Menu

The menu settings page shows current settings for the menus, a list of installed options, and available printer memory. You can use this page to verify that all printer options are properly installed and the printer settings are set to what you want.

Settings Page

1 Make sure the printer power is On (|) and the

Ready status message appears on the display.

2 Press Menu> or <Menu to enter the menus.

3 Continue to press and release Menu> or <Menu until you see UTILITIES MENU on the second line of the display.

4 Press Select.

5 Press Menu> until Print Menus appears on the sec- ond line of the display.

6 Press Select.

The message Printing Menu Settings appears and remains on the operator panel display until the page prints. The printer returns to the Ready state after the menu settings page prints.

If an error message appears, see “Understanding Printer Messages” on page 151 for more information.

21 Printing the Menu Settings Page

Page 34 of the Lexmark M412 user manual — 22 Chapter 1: Setting Up Your Printer
Page 34 · click to enlarge
Page 34

Installing the Operator Panel

If English is your preferred language, continue with “Installing Printer Drivers and Utilities” on page 24.

Overlay

If English is not your preferred language, complete the fol- lowing steps to customize the operator panel.

1 Locate the operator panel overlay.

If this User’s Guide is printed in a language other than English, an overlay for the operator panel is included with the printer. The overlay has trans- lated names for the operator panel buttons.

2 Peel the protective backing off the overlay.

Lexmark M412 — Overlay diagram (page 34)
Fig. 28 · Overlay

3 Align the operator panel overlay on the operator panel and press it into place as shown.

Rub the overlay firmly to make sure that it adheres securely.

4 Peel the protective covering away from the top of the overlay.

5 Continue with “Changing the Operator Panel Dis- play Language” on page 23 to change the display language to match the overlay.

22 Chapter 1: Setting Up Your Printer

Page 35 of the Lexmark M412 user manual — 23 Changing the Operator Panel Display Language
Page 35 · click to enlarge
Page 35

Changing the Operator Panel Display Language

Complete the following steps to change the language of the menus and messages that appear on the operator panel display:

1 Press the Menu> or <Menu button to enter the menus.

2 Continue to press and release Menu> or <Menu until

SETUP MENU appears on the second line of the dis- play.

3 Press the Select button.

4 Press Menu> until Display Language appears on the second line of the display.

5 Press Select.

6 Press Menu> until your preferred language appears on the second line of the display.

7 Press Select.

The printer resets and displays text in the requested language.

23 Changing the Operator Panel Display Language

Page 36 of the Lexmark M412 user manual — 24 Chapter 1: Setting Up Your Printer
Page 36 · click to enlarge
Page 36

Installing Printer

1 Locate the Drivers, MarkVision and Utilities CD that comes with your printer.

Drivers and

Utilities

If your computer does not have a CD-ROM drive, you can transfer the information on the CD to dis- kettes. Locate a computer with a CD-ROM drive, start the CD-ROM utility, and follow the instruc- tions presented to create diskettes.

2 Follow the instructions in the booklet included with the CD to start the printer setup utility.

The setup utility lets you install printer drivers and utilities to manage Lexmark printers attached to your network. See “Introducing MarkVision” on page 25 for more information.

3 If necessary, use standard network software to identify the printer to the LAN and to complete any other setup that may be needed.

24 Chapter 1: Setting Up Your Printer

Page 37 of the Lexmark M412 user manual — 25 MarkVision Printer Management Software
Page 37 · click to enlarge
Page 37

2 MarkVision

MarkVision Printer

This section provides a brief overview of the MarkVision printer utility and some of its key features. For more infor- mation on MarkVision, refer to the online Help or the doc- umentation on the Drivers, MarkVision and Utilities CD that comes with your printer:

Management

Software

  • Introduction to MarkVision
  • Installation Tips

Operating Systems

MarkVision for Windows 95/98/2000, Windows NT 4.0, Macintosh, and OS/2 Warp is shipped with your printer on the Drivers, MarkVision and Utilities CD.

Supported

Introducing

The MarkVision graphical user interface provides advanced, real-time, centralized management capabilities for Lexmark printers connected locally or attached directly to a network. Network users and administrators can also use the following MarkVision features to increase productivity:

MarkVision

  • Centralized setup capabilities let you quickly configure and install multiple printers.

– You can configure multiple printers simulta- neously from one workstation. – Automatic network printer discovery and multi- adapter flash update let you set up and configure

25 MarkVision Printer Management Software

Page 38 of the Lexmark M412 user manual — 26 Chapter 2: MarkVision
Page 38 · click to enlarge
Page 38

Lexmark network printers and change network addresses from one workstation.

  • Use MarkVision to easily manage and monitor your Lexmark printers.

– Messages on the MarkVision remote operator panel reflect printer real-time status. – The dynamic printer graphic provides a visual confirmation of installed options. – A list of installed features shows you printer capabilities.

  • MarkVision provides the tools to make printerrelated administrative tasks effortless.

– Monitor network print jobs, change their print- ing order, and hold or delete specific jobs. – Use asset management options to maintain printer inventory, assign property tags, track page counts, and gather job statistics. – Download and manage resources such as fonts, demo pages, and overlays.

MarkVision for Intranet Servers

This section provides a brief overview of MarkVision for Intranet Servers and some of its key features. For more information on MarkVision for Intranet Servers, refer to the documentation installed with the software:

  • MarkVision for Intranets User’s Guide .
  • MarkVision Installation and Configuration Guide .

This document is also located on the Drivers, MarkVision and Utilities CD that comes with your printer.

Introducing MarkVision for Intranet Servers

MarkVision for Intranet Servers is a Web-based printer management utility that:

  • Lets you monitor and manage devices using a Web browser from any PC with intranet access.

26 Chapter 2: MarkVision

Page 39 of the Lexmark M412 user manual — 27 MarkVision for UNIX Networks
Page 39 · click to enlarge
Page 39
  • Enables print management over your existing intranet infrastructure using TCP/IP.
  • Offers a cross-platform solution for Windows and UNIX users.
  • Lets you manage multivendor printers.

Network users and administrators can also use the follow- ing MarkVision features to increase productivity.

Maps

Locate printers quickly in your organization by position- ing printer icons on a map to show not only printer status, but also actual printer location.

Filters

Search for devices using criteria such as printer status and installed features.

Filters automatically organize printers into groups based on real-time status information.

Remote Updates

Remotely update firmware on multiple Lexmark print servers simultaneously.

MarkVision for UNIX Networks

MarkVision for UNIX/Sun offers enterprise scalability, reliability, and performance that helps you easily set up, manage, and maintain printers across networks. Ulti- mately, this reduces help desk costs and increases network administrator productivity using:

  • Centralized Lexmark printer setup capabilities.
  • Remote monitoring and management.
  • Proactive status alerts on Lexmark printers.
  • Tools that allocate printing expenses, balance workload, and access printing resources.

27 MarkVision for UNIX Networks

Page 40 of the Lexmark M412 user manual — 28 Chapter 2: MarkVision
Page 40 · click to enlarge
Page 40

MarkVision Simple Network Management Protocol (SNMP) Services let administrators manage popular mul- tivendor printers.

MarkVision for UNIX Networks and Intranet Servers is recommended to assist in remote printer setup for UNIX platforms.

To purchase MarkVision for UNIX, contact the place where you bought your printer or visit the Lexmark Web site at www.lexmark.com

Lexmark MarkTrack

MarkTrack™is a network printer reporting software package that helps administrators manage printing envi- ronments more efficiently. Administrators can use Mark- Track to:

  • Retrieve and analyze network printer information from a Web browser.
  • Allocate printing resources more efficiently.
  • Make better purchasing decisions.
  • Allocate printing costs to different departments.
  • Provide statistical information on employee printing habits.
  • Track Lexmark and SNMP-compliant printers.
  • Collect, analyze, and create reports using MarkVision Printer Inventory and Job Statistics data or SNMP MIB data.
  • Create reports using a Web server.
  • View reports using a Web browser.
  • Create an inventory of network printer assets automatically.
  • Analyze printing for the enterprise.
  • Plan ahead for supplies purchases, maintenance schedules, and printer replacement.

For more information on MarkTrack, refer to the product information, contact the place where you bought your

28 Chapter 2: MarkVision

Page 41 of the Lexmark M412 user manual — 29 Lexmark NetPnP
Page 41 · click to enlarge
Page 41

printer, or visit the Lexmark Web site at www.lexmark.com

Lexmark NetPnP NetPnP automates the configuration and installation of Lexmark printers on a network. NetPnP senses when a new printer is attached to the network, automatically cre- ates a shared printer object on a Windows NT 4.0 system, and notifies users by e-mail that the printer is available for printing. It also notifies IT administrators by e-mail when a new printer is detected or when an error occurs during automatic printer installation.

  • Lets administrators make printers available to users within seconds.
  • Extends network printer installation to include the end user by installing all necessary components that enable printing to workstations across the network.
  • Provides huge productivity gains when rolling out large numbers of network printers.
  • Supports a wide range of printer installation options for IT administrators, from fully automatic installation to prompted confirmations.
  • Lets you customize network printer installation in Windows NT environments running TCP/IP.
  • Automates the setup of Lexmark network printers, eliminating more than a dozen steps in the process.

Software Installation and Distribution Tools

On the Drivers, MarkVision and Utilities CD, Lexmark's all- in-one software installation utility provides IT administra- tors with time-saving installation and distribution tools that enhance productivity and improve efficiency.

  • Software installation and updates by way of the Lexmark Web site.

Users can initiate Web updates or schedule updates to run periodically. This ensures that users have the most recent version of Lexmark software and driv-

29 Lexmark NetPnP

Page 42 of the Lexmark M412 user manual — 30 Chapter 2: MarkVision
Page 42 · click to enlarge
Page 42

ers on their workstations with the least amount of effort.

  • Scripting capability to distribute software to users on the network.

IT administrators can store software and driver installation settings in a file. This file can then be used to automatically distribute the software to multiple workstations simultaneously.

  • Distribution of drivers with custom settings to users.

IT administrators can remotely install, update, and distribute drivers with custom settings to users on the network, eliminating time-consuming worksta- tion driver installation and configuration.

Optra Forms Optra Forms combines data from a customer’s application with printer-resident electronic forms to produce com- pleted forms such as invoices, statements, pick slips, labels, and purchase orders. Support for bar codes, spe- cialized graphics and other options is included.

The same data can be sent to several remote printers with different resident forms so that the completed forms can be customized for the specific printer location. For exam- ple, the same purchase order information can be sent to different printers and printed with different addresses and logos.

Optra Forms:

  • Requires no server-based or host-based merge program or software.
  • Can be used:

– With virtually any ASCII text print file from any platform, mainframe, AS/400, UNIX or worksta- tion. – Over Coax, Twinax, parallel, serial or LAN (TCP/IP).

  • Generally makes no changes to database applications.

30 Chapter 2: MarkVision

Page 43 of the Lexmark M412 user manual — Customers
Page 43 · click to enlarge
Page 43
  • Prints different forms at different locations from the same database.
  • Globally updates forms quickly and easily over the LAN.
  • Provides support for bar codes, color, duplex, multipage form sets, and more.
  • Stores forms as efficient, compact forms in flash.
  • Works with Optra M410 and M412 printers and the Optra T and Optra W laser printer families using the Optra Forms™1, 2, 4, 8, and 16MB Flash DIMMs or Optra Forms Hard Disk.

Solaris Ready Printers for Sun

Solaris Ready printers are specially configured for Sun users. They are Ethernet-ready and include Sun-specific documentation as well as MarkVision for Sun Systems and Intranet Servers. These applications provide seamless installation in Sun Solaris network environments.

Customers

31 Solaris Ready Printers for Sun Customers

Page 44 of the Lexmark M412 user manual — 32 Chapter 2: MarkVision
Page 44 · click to enlarge
Page 44

32 Chapter 2: MarkVision

Page 45 of the Lexmark M412 user manual — 33 Using the Operator Panel and Menus
Page 45 · click to enlarge
Page 45

Using the Operator Panel

and Menus

This chapter contains information about using the operator panel, changing printer settings, and under- standing operator panel menus.

You can change most printer settings from your software application or printer driver. Settings you change from the application or driver apply only to the job you are prepar- ing to send to the printer.

If there is a setting you cannot change from your software application, use the operator panel or the remote operator panel available from the MarkVision utility. See “MarkVi- sion” on page 25 for information about MarkVision. Changing a printer setting from the operator panel or from MarkVision makes that setting the user default.

If you are familiar with using an operator panel similar to this, you may want to skip to “Overview of Printer Menus” on page 43.

33 Using the Operator Panel and Menus

Page 46 of the Lexmark M412 user manual — 34 Chapter 3: Using the Operator Panel and Menus
Page 46 · click to enlarge
Page 46

Using the Operator Panel

The operator panel, on the front left-side of your printer, has a 2-line by 16-character liquid crystal display (LCD), one printer indicator light, and six buttons. Notice the Menu button is split into two functioning halves; there- fore, it works like two buttons.

The numbers on the operator panel by the names of the buttons are only used for entering your Personal Identifi- cation Number (PIN) if you send a print job that is confi- dential. For more information, see CONFIDENTIAL JOB on page 60 and “Entering a Personal Identification Number (PIN)” on page 111.

LCD

Printer Indicator

The printer indicator light gives information about the status of your printer.

Light

On Solid The printer is On (|) and in the Ready state.

Blinking The printer is On (|) and Busy.

Off The printer is Off (O).

34 Chapter 3: Using the Operator Panel and Menus

Show 4 more labels / short text on this page
Menu Select Return · Go Stop · Printer Indicator Light · Light State Meaning
Page 47 of the Lexmark M412 user manual — 35 Using the Operator Panel
Page 47 · click to enlarge
Page 47

Operator Panel

Use the operator panel buttons to open a menu, scroll through a list of values, change printer settings, respond to printer messages, temporarily stop all print activity, and key in a PIN. The following table describes the func- tions of each button.

Buttons

If this User’s Guide is printed in a language other than English, an operator panel overlay with translated buttons and light names is included with your printer. See “Install- ing the Operator Panel Overlay” on page 22 for more information.

Operator Panel Buttons

Go Press the Go button to:

  • Return to the Ready state if the printer is in an offline situation (the Ready message does not appear on the display).
  • Exit printer menus and return to the Ready state.
  • Clear operator panel error messages.
  • Resume printing after loading print material and clearing paper jams.
  • Exit Power Saver .

If you have changed printer settings from the operator panel menus, press Go before sending a job to print. The printer must display Ready for jobs to print.

Each end of the button has a function. Press the Menu> or <Menu button:

  • At the Ready message, to take the printer offline (out of the Ready state) and enter the menus. Menu> takes you to the first menu in the menus. <Menu takes you to the last menu in the menus.
  • At the Busy message, to list the menu items in the JOB MENU .
  • When the printer is offline: - Press Menu> to go to the next item in the menus, or - Press <Menu to go to the previous item in the menus.
  • For menu items that have numerical values, such as Copies , press and hold Menu> to scroll forward, or <Menu to scroll backward. Release the button when the number you want displays.

35 Using the Operator Panel

Button Function · Menu> and <Menu

Page 48 of the Lexmark M412 user manual — 36 Chapter 3: Using the Operator Panel and Menus
Page 48 · click to enlarge
Page 48

Operator Panel Buttons (continued)

Select Press the Select button to:

  • Select the menu shown on the second line of the display. Depending on the type of menu, this action: - Opens the menu and displays the first item in the menu. - Opens the menu item and displays the default setting.
  • Save the displayed menu item as the new default setting. The printer displays the Saved message briefly and returns to the menu item.
  • Clear certain messages from the operator panel display.
  • Continue printing after the Change <input source> message displays. See Change <input source> on page 167 for more information.

Return Press the Return button to return to the previous menu level or menu item.

Stop Press the Stop button at the Ready, Busy, or Waiting message to temporarily stop all activity and take the printer offline. The operator panel status message changes to Not Ready. No data is lost.

Press Go to return the printer to the Ready, Busy, or Waiting state.

1, 2, 3, 4, 5, 6 The numbers located next to the names of the buttons are only used for entering your Personal Identification Number (PIN) after you send a Confidential Job. For more information, see “Entering a Personal Identification Number (PIN)” on page 111.

36 Chapter 3: Using the Operator Panel and Menus

Button Function

Page 49 of the Lexmark M412 user manual — 37 Printer Messages
Page 49 · click to enlarge
Page 49

Printer Messages The operator panel displays three types of messages:

  • Status messages provide information about the current state of the printer.
  • Attendance messages report printer errors that you must resolve.
  • Service messages indicate printer failures that may require servicing.

Status Messages When the Ready status message displays, the printer is ready to receive a print job. While a job is processing or printing, the Busy status message or a customized mes- sage appears on the first line of the operator panel display.

The screen to the left is an example of an operator panel message. The printer status appears on the first line of the display. The second line displays messages, such as warn- ing messages, that give more information about printer status.

The Busy message identifies the printer language (PCL emulation) used for the print job. The Parallel mes- sage tells you that the printer is processing data received by the parallel port.

Attendance

Attendance messages help you solve printer problems.

Messages

For example, if print material is jammed in the printer, the message 200 Paper Jam Remove Cartridge appears on the display.

This message tells you to open the printer upper front door and check for jammed print material.

200 Paper Jam Remove Cartridge

Service Messages Service messages notify you of printer failures that may require a service call.

37 Printer Messages

Busy PCL Parallel

Page 50 of the Lexmark M412 user manual — 38 Chapter 3: Using the Operator Panel and Menus
Page 50 · click to enlarge
Page 50

Operator Panel

A number of menus are available to make it easy for you to change printer settings. The diagram on page 43 shows the menus and all of the menu items available in each menu. The items in each menu and the values you can select are described in more detail in the tables beginning on page 44.

Menus

Some menus appear only if a specific option is installed in the printer. Other menu items may only be effective for a particular printer language. You can select these values at any time, but they only affect printer function when you use the specified printer language.

An asterisk (*) next to a value in the tables indicates the factory default setting. These settings are the original printer settings. (Factory defaults may vary for different coun- tries.) See Factory Defaults on page 57 or on page 107 for more information.

When you select a new setting from the operator panel, the asterisk moves next to the selected setting to identify it as the current user default setting. These settings are active until new ones are stored or the factory defaults are restored. See “Changing Menu Settings” on page 40 for more information.

38 Chapter 3: Using the Operator Panel and Menus

Page 51 of the Lexmark M412 user manual — 39 Operator Panel Menus
Page 51 · click to enlarge
Page 51

Printing the Menu

The menu settings page shows current settings for the menus, a list of installed options, and available printer memory. You can use this page to verify that the printer options are properly installed and the printer settings are set to what you want.

Settings Page

See “Using the Operator Panel” on page 34 to identify the display and operator panel buttons if you need help.

To print a menu settings page:

1 Make sure the printer power is On (|) and the

Ready status message appears on the display.

2 Press Menu> or <Menu to enter the menus.

3 Continue to press and release Menu> or <Menu until you see UTILITIES MENU on the second line of the display.

4 Press Select.

5 Press Menu> until Print Menus appears on the sec- ond line of the display.

6 Press Select.

The message Printing Menu Settings appears and remains on the operator panel display until the page prints. The printer returns to the Ready state after the menu settings page prints.

If an error message appears on the display, see “Understanding Printer Messages” on page 151.

7 If you installed options, verify that they are listed on the menu settings page under “Installed Fea- tures.”

If an option you installed does not appear on the page, turn the printer power Off (O), unplug the printer power cord, reinstall the option, and print the menu settings page again.

39 Operator Panel Menus

Page 52 of the Lexmark M412 user manual — 40 Chapter 3: Using the Operator Panel and Menus
Page 52 · click to enlarge
Page 52

Changing Menu Settings

You can use the operator panel to change printer settings and customize your printer to meet your specific needs.

To select a new value as the default setting:

1 From the Ready state, press Menu> or <Menu to enter the menus.

2 Continue to press and release Menu> or <Menu until the menu you need appears on the second line of the display.

See “Overview of Printer Menus” on page 43 for a list of the menus and their menu items.

3 Press Select.

The menu opens and the first menu item in the menu appears on the second line of the display.

4 Press Menu> or <Menu until the menu item you need appears on the second line of the display.

5 Press Select.

An asterisk (*) appears beside the current user default setting for that menu item.

Some menu items have submenus. For example, if you select PAPER MENU, and then select the PAPER TYPE menu item, you must select another menu (such as Tray 1 Type) before the available values dis- play.

A value can be:

– An On or Off setting. – A phrase or word that describes a setting. – A numerical value that you can increase or decrease.

6 Press Menu> or <Menu until the value you need appears on the second line of the display.

40 Chapter 3: Using the Operator Panel and Menus

Page 53 of the Lexmark M412 user manual — 41 Operator Panel Menus
Page 53 · click to enlarge
Page 53

7 Press Select.

An asterisk (*) appears beside the value to indicate that it is now the user default setting. The display shows the new setting for one second and then clears. The Saved message displays, then the previ- ous list of menu items appears on the operator panel display.

8 Press Return to go back to previous menus or menu items and set new default settings.

9 Press Go to return to Ready if this is the last printer setting you want to change.

Disabling the Operator Panel

To disable the menus so that changes cannot be made to the printer default settings:

Menus

1 Turn the printer power Off (O).

2 Press and hold the Select and Return buttons and turn the printer power On (|).

3 Release the buttons when Performing Self Test appears on the operator panel display.

When the printer self test completes, the CONFIG MENU displays.

4 Press Menu> until Panel Menus displays on the sec- ond line.

5 Press Select.

6 Press Menu> until Disable displays on the second line of the display.

7 Press Select.

41 Operator Panel Menus

Page 54 of the Lexmark M412 user manual — 42 Chapter 3: Using the Operator Panel and Menus
Page 54 · click to enlarge
Page 54

8 The Saved message briefly appears, then Disabling

Menus displays.

The CONFIG MENU displays again with Panel Menus on the second line.

9 Press Menu> until Exit Config Menu displays on the second line.

10 Press Select.

Activating Menu Changes briefly appears, and then Performing Self Test briefly appears. The printer returns to the Ready state.

To enable the menus, repeat the previous steps and select Enable instead of Disable.

42 Chapter 3: Using the Operator Panel and Menus

Page 55 of the Lexmark M412 user manual — 43 Operator Panel Menus
Page 55 · click to enlarge
Page 55

Overview of Printer Menus

Menus or menu items in italics only appear on the display if the corresponding option is installed. Capitalized menu items (for example, PAPER SIZE) have submenus. See the tables on the following pages for a list of the values for each menu item.

PAPER MENU (page 44)

FINISHING MENU (page 53)

UTILITIES MENU (page 57)

JOB MENU (page 59)

QUALITY MENU (page 71)

Paper Source PAPER SIZE PAPER TYPE CUSTOM TYPES Substitute Size Configure MP PAPER TEXTURE PAPER WEIGHT PAPER LENGTH

Copies Blank Pages Collation Separator Sheets Separator Source Multipage Print Multipage Order Multipage View Multipage Border

Print Menus Print Net1 Setup Print Fonts Print Directory Factory Defaults Format Flash Defragment Flash Format Disk Job Acct Stat Hex Trace

Cancel Job CONFIDENTIAL JOB HELD JOBS Reset Printer Print Buffer

Print Resolution Toner Darkness PQET PictureGrade

SETUP MENU (page 73)

PCL EMUL MENU (page 79)

POSTSCRIPT MENU (page 83)

PARALLEL MENU (page 84)

SERIAL MENU (page 87)

Printer Language Power Saver1 Resource Save Download Target Print Timeout Wait Timeout Auto Continue Jam Recovery Page Protect Print Area Display Language Alarm Control Job Buffer Size Job Accounting Job Acct Limit

Font Source Font Name Point Size Pitch Symbol Set Orientation Lines Per Page A4 Width TRAY RENUMBER Auto CR after LF Auto LF after CR

Print PS Error Font Priority

STD PARALLEL PARALLEL OPT 1 PCL SmartSwitch PS SmartSwitch NPA Mode Parallel Buffer Job Buffering Advanced Status Protocol Honor Init Parallel Mode 12 Parallel Mode 2

SERIAL OPTION 1 PCL SmartSwitch PS SmartSwitch NPA Mode Serial Buffer RS-232/RS-422 RS-422 Polarity Serial Protocol Robust XON Baud Data Bits Parity Honor DSR

NETWORK MENU (page 91)

INFRARED MENU (page 93)

LOCALTALK MENU (page 96)

USB MENU (page 99)

FAX MENU (page 102)

NETWORK OPTION 1 PCL SmartSwitch PS SmartSwitch NPA Mode Network Buffer Network 1 Setup

Infrared Port PCL SmartSwitch PS SmartSwitch NPA Mode Infrared Buffer Window Size Transmit Delay Max Baud Rate

LocalTalk Port PCL SmartSwitch PS SmartSwitch NPA Mode LocalTalk Buffer NPA Hosts LocalTalk Name LocalTalk Addr LocalTalk Zone

STANDARD USB USB OPTION 1 PCL SmartSwitch PS SmartSwitch NPA Mode USB Buffer Job Buffering

Fax Port Fax Baud Fax Data Bits Fax Parity Fax Buffer Fax Paper Size Fax Paper Type

1 Some printer models released in the year 2000 or later designated as Energy Star printers cannot have Power Saver disabled. 2 Parallel Mode 1 is not supported on the Optra M412 printer. For all menus:

CONFIG MENU (page 106)

Prt Quality Pgs Panel Menus Buffered Jobs Factory Defaults NARROW MEDIA Exit Config Menu

– Press Menu> or <Menu to enter the menus and scroll through the options. – Press Select to choose a menu, menu item, or value. – Press Return to back up to the previous menu level. For all menus except CONFIG MENU:

– Press Go to return to Ready.

43 Operator Panel Menus

Page 56 of the Lexmark M412 user manual — 44 Chapter 3: Using the Operator Panel and Menus
Page 56 · click to enlarge
Page 56

Paper Menu Use the PAPER MENU to define all settings relating to print material input and output, as well as the specific print material you are using with your printer.

Paper Menu

Paper Source Tray 1* Tray 2 MP Feeder Manual Paper Manual Env

The Paper Source setting identifies the default paper source.

Tray 2 is available only if the optional 500-sheet drawer is installed. See “Optional 500-Sheet Drawer” on page 223 for more information.

Select Manual Paper when manually feeding a sheet of print material other than an envelope through the multipurpose feeder.

Select Manual Env when manually feeding an envelope through the multipurpose feeder.

MP Feeder displays only if Configure MP is set to Cassette. If Paper Source is set to MP Feeder and Configure MP is set to First, the Paper Source setting automatically changes to Tray 1.

If you are using the same size and type of print material in two paper sources (and the Paper Size and Paper Type settings are correctly set), the trays are automatically linked. When one paper source is empty, print material automatically feeds from the other paper source. See “Tray Linking” on page 135 for more information.

44 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 57 of the Lexmark M412 user manual — 45 Operator Panel Menus
Page 57 · click to enlarge
Page 57

Paper Menu (continued)

PAPER SIZE Tray 1 Size Tray 2 Size

Each of the above menu items support the following values as a second menu:

A4* (Country specific) JIS B5 Letter* (Country specific) Legal Executive

A4* (Country specific) A5 JIS B5 Letter* (Country specific) Legal Executive Universal 7 ¾ Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope

45 Operator Panel Menus

Menu Item Values · MP Feeder Size · *Factory default

Page 58 of the Lexmark M412 user manual — 46 Chapter 3: Using the Operator Panel and Menus
Page 58 · click to enlarge
Page 58

Paper Menu (continued)

A4* (Country specific) A5 JIS B5 Letter* (Country specific) Legal Executive Universal

7 ¾ Envelope 9 Envelope 10 Envelope* (Country specific) DL Envelope* (Country specific) C5 Envelope B5 Envelope Other Envelope

The PAPER SIZE setting identifies the default formatting size for each paper source. See the tables beginning on page 116 for a list of the dimensions for each paper and envelope size.

Select Manual Pap Size when manually feeding a single sheet of print material other than an envelope through the multipurpose feeder.

Select Manual Env Size when manually feeding a single envelope through the multipurpose feeder.

Universal refers to any size that is not considered a standard size. Select Universal from the PAPER SIZE menu when you load print material that does not match any of the other available sizes. The printer automatically formats the page for the maximum possible size. You can then set the actual page size from your application.

Select Other Envelope from the PAPER SIZE menu when you load envelopes that do not match any of the other available sizes. The printer automatically formats for the maximum possible envelope size. You can then set the actual envelope size from your application.

46 Chapter 3: Using the Operator Panel and Menus

Show 5 more labels / short text on this page
Menu Item Values · PAPER SIZE (continued) · Manual Pap Size · Manual Env Size · *Factory default
Page 59 of the Lexmark M412 user manual — 47 Operator Panel Menus
Page 59 · click to enlarge
Page 59

Paper Menu (continued)

PAPER TYPE Tray 1 Type Tray 2 Type Manual Pap Type

Each of the above menu items support the following values as a second menu:

Plain Paper* Card Stock Transparency Labels Bond Letterhead Preprinted Colored Paper Custom Type 1 Custom Type 2* Custom Type 3 Custom Type 4 Custom Type 5 Custom Type 6

Plain Paper Card Stock Transparency Labels Bond Envelope Letterhead Preprinted Colored Paper Custom Type 1 Custom Type 2 Custom Type 3 Custom Type 4 Custom Type 5 Custom Type 6*

47 Operator Panel Menus

Menu Item Values · MP Feeder Type · *Factory default

Page 60 of the Lexmark M412 user manual — 48 Chapter 3: Using the Operator Panel and Menus
Page 60 · click to enlarge
Page 60

Paper Menu (continued)

Envelope* Custom Type 1 Custom Type 2 Custom Type 3 Custom Type 4 Custom Type 5 Custom Type 6

The PAPER TYPE setting lets you specify the type of print material installed in each paper source. This setting is used by the printer in the following ways:

  • Enables the printer to optimize print quality for the specified print material.
  • Enables you to select paper sources through your software application by selecting only a type and size. A source selection is unnecessary.
  • Enables the printer to automatically link paper sources. Any sources that contain the same type and size of print material are automatically linked by the printer if you have set the PAPER SIZE and the PAPER TYPE to the correct settings for the paper sources. See “Tray Linking” on page 135 for more information.

Select Manual Pap Type when manually feeding a single sheet of print material through the multipurpose feeder.

Select Manual Env Type when manually feeding an envelope through the multipurpose feeder.

Custom Type 1 through 6 refers to special types of print materials. You can change the names through a utility, such as MarkVision. For more information on setting the Custom Type names, see CUSTOM TYPES on page 49.

If you are using different print material in the paper sources, each source with a different print material must have the PAPER SIZE and PAPER TYPE set to a unique value to disable the automatic tray linking feature. Otherwise, if a paper source becomes empty, the printer selects print material from another source since the printer sees the trays as linked. This might cause a one-page letter to print on a sheet of labels or on a transparency. See “Tray Linking” on page 135 for more information.

48 Chapter 3: Using the Operator Panel and Menus

Show 4 more labels / short text on this page
Menu Item Values · PAPER TYPE (continued) · Manual Env Type · *Factory default
Page 61 of the Lexmark M412 user manual — 49 Operator Panel Menus
Page 61 · click to enlarge
Page 61

Paper Menu (continued)

CUSTOM TYPES Custom Type x (where x represents a custom type from 1 to 6)

Paper* Card Stock Transparency Labels Envelope

The CUSTOM TYPES setting identifies the kind of print material used for each of the Custom Types available in the PAPER TYPE menu item. This print material designation optimizes print quality settings when you select print material from a paper source when the type is set to Custom Type x. If a user-defined name is available, the name displays instead of Custom Type x, where x represents a number 1 through 6. The user-defined name is truncated to 14 characters.

Substitute Size Off Letter/A4*

Select Letter/A4 to let the printer automatically print A4-size jobs on letter-size paper and letter-size jobs on A4-size paper, if the requested size is not currently installed in the paper source.

Configure MP Cassette* Manual First

When the multipurpose feeder is set to Cassette and the PAPER SIZE and PAPER TYPE settings are set correctly, the printer treats the multipurpose feeder like any other paper source. If a print job requests a size print material that is only loaded in the multipurpose feeder, the printer selects the print material from the multipurpose feeder for the print job.

Select Manual to manually feed single sheets of print material through the multipurpose feeder. The multipurpose feeder acts like a manual feed slot and you can feed only one sheet of print material through at a time.

If you set Configure MP to First, the printer feeds print material from the multipurpose feeder until it is empty, regardless of the paper source or paper size requested for the job.

49 Operator Panel Menus

Menu Item Values · *Factory default

Page 62 of the Lexmark M412 user manual — 50 Chapter 3: Using the Operator Panel and Menus
Page 62 · click to enlarge
Page 62

Paper Menu (continued)

PAPER TEXTURE Plain Texture Card Stock Text Trnsprncy Text Labels Texture Bond Texture Envelope Texture Ltrhead Texture Preprint Texture Colored Texture Custom 1 Texture Custom 2 Texture Custom 3 Texture Custom 4 Texture Custom 5 Texture Custom 6 Texture

Each of the above menu items support the following three values as a second menu:

  • Smooth
  • Normal*
  • Rough

Select the appropriate PAPER TEXTURE value (Smooth, Normal, or Rough) for each PAPER TYPE, including the Custom Types, that you are using. Set the correct PAPER TEXTURE value for your print material to make sure characters print clearly, without dropouts or voids. If the characters on your printed page appear broken or poorly-formed, set PAPER TEXTURE to Rough. If characters on your printed page appear smeared, set PAPER TEXTURE to Smooth or Normal.

The PAPER TEXTURE setting works in connection with the PAPER TYPE and PAPER WEIGHT settings. You may need to change those settings to optimize print quality for your specific print material.

If a user-defined texture is available, its name displays as a value instead of Custom x Texture, where x represents a number 1 through 6. The user-defined name is truncated to 14 characters.

50 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 63 of the Lexmark M412 user manual — 51 Operator Panel Menus
Page 63 · click to enlarge
Page 63

Paper Menu (continued)

PAPER WEIGHT Plain Weight CardStock Weight Trnsprncy Weight Labels Weight Bond Weight Envelope Weight Ltrhead Weight Preprint Weight Colored Weight Custom 1 Weight Custom 2 Weight Custom 3 Weight Custom 4 Weight Custom 5 Weight Custom 6 Weight

Each of the above menu items support the following three values as a second menu:

  • Light
  • Normal*
  • Heavy

Select the appropriate PAPER WEIGHT value (Light, Normal, or Heavy) for each PAPER TYPE, including the Custom Types, that you are using. Set the correct PAPER WEIGHT value for your print material to make sure the toner adheres properly to the page. If you have trouble with toner rubbing off the page, set PAPER WEIGHT to Heavy. If your printed pages are curling excessively, set PAPER WEIGHT to Normal or Light.

The PAPER WEIGHT setting works in connection with the PAPER TYPE and PAPER TEXTURE settings. You may need to change those settings to optimize print quality for your specific print material.

If a user-defined weight is available, its name displays as a value instead of Custom x Weight, where x represents a number 1 through 6. The user-defined name is truncated to 14 characters.

51 Operator Panel Menus

Menu Item Values · *Factory default

Page 64 of the Lexmark M412 user manual — 52 Chapter 3: Using the Operator Panel and Menus
Page 64 · click to enlarge
Page 64

Paper Menu (continued)

PAPER LENGTH Plain Length CardStock Length Trnsprncy Length Labels Length Bond Length Envelope Length Ltrhead Length Preprint Length Colored Length Custom 1 Length Custom 2 Length Custom 3 Length Custom 4 Length Custom 5 Length Custom 6 Length

Each of the above menu items support the following values as a second menu:

  • Short
  • Normal*

Select the appropriate PAPER LENGTH value (Normal or Short) for each printer paper type.

Set the PAPER LENGTH value to Short if your print material is 152.4 mm (6 in.) or less in length. Set the PAPER LENGTH value to Normal for all other print material.

Print material 152.4 mm (6 in.) or less in length can only be fed through the multipurpose feeder and must exit to the rear output bin.

If a user-defined length is available, its name displays as a value instead of Custom x Length, where x represents a number 1 through 6. The user-defined name is truncated to 14 characters.

52 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 65 of the Lexmark M412 user manual — 53 Operator Panel Menus
Page 65 · click to enlarge
Page 65

Finishing Menu Use the FINISHING MENU to define all settings relating to printer output.

Finishing Menu

The Copies setting determines the number of copies printed for each page. The printer does not automatically collate the copies. For example, if you send three pages to print and set Copies to 2, the printer prints page 1, page 1, page 2, page 2, page 3, page 3.

For information about how to use the Copies setting with the Collation setting, see Collation as follows.

Blank Pages Do Not Print* Print

Select Print to include application-generated blank pages with your print job.

Select Do Not Print if you do not want the printer to print any application-generated blank pages that appear in your document.

When Collation is set to Off, the printer prints each page of a job the number of times as specified by the Copies setting. For example, if you send three pages to print and set Copies to 2, the printer prints page 1, page 1, page 2, page 2, page 3, page 3.

When Collation is set to On, the printer prints the entire job the number of times as specified by the Copies setting. For example, if you send three pages to print and set Copies to 2, the printer prints page 1, page 2, page 3, page 1, page 2, page 3.

Many applications collate documents by repeatedly sending the file to the printer. As a result, the printer must process each print job until the correct number of copies has printed. This requires additional time since the printer must process the same pages over again. By using Collation, the printer processes the file only once, saves the file in printer memory, and prints the multiple copies. This saves processing time for the printer and for the application, and overall printing time may be reduced.

For Collation to work effectively, your software application must recognize this printer feature and not send the job to the printer multiple times. Your application must also let you specify the number of copies needed or let you use the printer default setting for Copies.

Select Collation from the operator panel or from the printer driver. For best results, select Collated in the printer driver and set the number of copies to one. In your application, select Uncollated (if the option is available) and then select the number of copies you want.

If the job is complex or exceeds the memory capacity of your printer, you may receive a 37 Insufficient Collation Area message. Press Go to clear the message. The printer collates the remaining pages in memory. If you reset the printer, the printer discards the job. See 37 Insufficient Collation Area on page 160 for more information.

53 Operator Panel Menus

Show 4 more labels / short text on this page
Menu Item Values · Copies 1*…999 · Collation Off* On · *Factory default
Page 66 of the Lexmark M412 user manual — 54 Chapter 3: Using the Operator Panel and Menus
Page 66 · click to enlarge
Page 66

Finishing Menu (continued)

Separator Sheets None* Between Copies Between Jobs Between Pages

You can have the printer insert blank separator sheets between jobs, between multiple copies of a job, or between each page of a job. Separator sheets are pulled from the source specified in the Separator Source menu item.

Select Between Copies for multiple copy jobs. If Collation is set to Off, a blank page is inserted between sets of each printed page. If Collation is set to On, a blank page is inserted between each copy of the job.

Select Between Jobs to insert a blank page after each print job. This may be helpful when several people are using the printer.

Select Between Pages to insert a blank page between each page of a job. This is useful if you are printing transparencies and want to reduce static build-up when stacking transparencies in the output bin.

Separator Source Tray 1* Tray 2 MP Feeder

If you are using separator sheets, Separator Source lets you specify the paper source that holds the separator sheets.

Only installed paper sources display as values. You can only select MP Feeder as the separator source if Configure MP is set to Cassette. If Separator Source is set to MP Feeder and Configure MP is set to First, the Separator Source setting automatically changes to Tray 1. See “Configure MP” on page 49 for more information.

Multipage Print Off* 2-Up 3-Up 4-Up 6-Up 9-Up 12-Up 16-Up

Use the Multipage Print (N-up) setting to print multiple page images on a single page. For example, 2-Up means two page images are printed on one page, 3-Up means three page images are printed on one page, and so forth.

The printer uses the Multipage Order, Multipage View, and Multipage Border settings to determine the order and orientation of the page images and if a border is printed around each page image.

Printer setting changes within a print job may affect the results you get when using Multipage Print.

54 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 67 of the Lexmark M412 user manual — 55 Operator Panel Menus
Page 67 · click to enlarge
Page 67

Finishing Menu (continued)

Multipage Order Horizontal* Vertical Rev Horizontal Rev Vertical

The Multipage Order setting determines the positioning of multiple page images on pages printed using Multipage Print. You may choose one of four different orders. The positioning of page images depends on if the pages are sent to the printer as portrait or landscape images. The following examples show the result of using each Multipage Order setting on a 4-Up print job.

Page 1 Page 2

Page 4 Page 3

Page 1 Page 3

Page 4 Page 2

Page 1 Page 2

Page 1 Page 3

Page 3 Page 4

Page 2 Page 4

Rev Horizontal Portrait Landscape

Rev Vertical Portrait Landscape

Page 2 Page 1

Page 3 Page 4

Page 3 Page 1

Page 2 Page 4

Page 2 Page 1

Page 3 Page 1

Page 4 Page 3

Page 4 Page 2

55 Operator Panel Menus

Show 4 more labels / short text on this page
Menu Item Values · Horizontal Portrait Landscape · Vertical Portrait Landscape · *Factory default
Page 68 of the Lexmark M412 user manual — 56 Chapter 3: Using the Operator Panel and Menus
Page 68 · click to enlarge
Page 68

Finishing Menu (continued)

Multipage View Auto* Long Edge Short Edge

Use the Multipage View setting to select the orientation of the printed page with respect to the page images during Multipage Print.

Select Auto to allow the printer to choose between portrait and landscape positioning.

Select Long Edge to position the long edge of the print material as the top of the page.

Select Short Edge to position the short edge of the print material as the top of the page.

Multipage Border None* Solid

Use the Multipage Border setting to specify if a border is printed around each page image during Multipage Print.

Select None if you do not want to print a border around each page image.

Select Solid to print a solid line border around each page image.

56 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 69 of the Lexmark M412 user manual — 57 Operator Panel Menus
Page 69 · click to enlarge
Page 69

Utilities Menu Use the UTILITIES MENU to print a variety of listings relating to available printer resources, printer settings, and print jobs. Additional menu items let you set up printer hardware and troubleshoot printer problems.

Utilities Menu

Print Menus Press Select to print the menu settings page.

The menu settings page is a list of the user default settings, the installed options, and the amount of available printer memory. This list also shows you the order of menu items.

Print Net1 Setup Press Select to print the internal print server settings page.

The internal print server settings page contains information on your network setup and the printer settings for your network as defined by the Network 1 Setup menu item in the NETWORK MENU. See “Network 1 Setup” on page 92 for more information.

Print Fonts PCL Fonts PS Fonts

Press Select to print a font sample list that shows all the fonts currently available in the selected printer language, PCL Fonts or PS Fonts. For more information, see “Printing a Font Sample List” on page 242.

Print Directory Press Select to print a list of all the resources stored in flash memory or on the hard disk option.

The Print Directory menu item is available only if at least one of the options is installed and formatted. Refer to the Technical Reference for details.

Factory Defaults Restore Do Not Restore

If you choose Restore:

  • All downloaded resources (fonts, macros, symbol sets) in printer memory (RAM) are deleted. (Resources residing in flash memory or on the hard disk option are unaffected.)
  • All menu settings are returned to the factory default values except: – Display Language (SETUP MENU) which is the operator panel display language. – All settings in the PARALLEL MENU, SERIAL MENU, NETWORK MENU, INFRARED

MENU, LOCALTALK MENU, USB MENU, and FAX MENU.

The message Restoring Factory Defaults briefly appears while the printer restores the factory default settings. See Restoring Factory Defaults on page 157 for more information.

57 Operator Panel Menus

Menu Item Values

Page 70 of the Lexmark M412 user manual — 58 Chapter 3: Using the Operator Panel and Menus
Page 70 · click to enlarge
Page 70

Utilities Menu (continued)

Format Flash Yes No

Formatting the flash memory option deletes all resources (fonts, macros, symbol sets) stored in flash memory and prepares the flash memory card to receive new resources.

The Format Flash menu item only displays if the installed flash memory option is not defective or Read/Write or Write protected. 51 Defective Flash may display when the printer is turned on, or during flash format and write operations. See 51 Defective Flash on page 161 for more information.

Defragment Flash Yes No

Defragmenting the flash memory option transfers all undeleted resources stored in flash memory to printer memory and then reformats the flash memory option. When the format operation is complete, the undeleted resources are loaded back into flash memory.

The Defragment Flash menu item only displays if the installed flash memory option is not defective or Read/Write or Write protected. 51 Defective Flash may display when the printer is turned on, or during flash format and write operations. See 51 Defective Flash on page 161 for more information.

37 Insufficient Defrag Memory displays if printer memory is too full to perform the Flash Memory Defragment operation. See 37 Insufficient Defrag Memory on page 160 for more information.

Format Disk Yes No

Formatting the hard disk option deletes all resources stored on the hard disk and prepares it to receive new resources.

The Format Disk menu item only displays if the installed hard disk option is not defective or Read/Write or Write protected. 61 Defective Disk may display when the printer is turned on, or during disk format and write operations. See 61 Defective Disk on page 165 for more infor- mation.

Format Disk does not display if Job Buffer Size is set to 100%. See Job Buffer Size on page 77 for more information.

58 Chapter 3: Using the Operator Panel and Menus

Menu Item Values

Page 71 of the Lexmark M412 user manual — 59 Operator Panel Menus
Page 71 · click to enlarge
Page 71

Utilities Menu (continued)

Job Acct Stat Print Clear

The Job Acct Stat menu item only displays if a hard disk option is installed in your printer and is not defective or Read/Write or Write protected. Job Accounting in the SETUP MENU must be set to On.

Select Print to print a list of statistics for a defined number of the most recent print jobs. (The number of jobs is determined by the value of the Job Acct Limit menu item in the SETUP MENU). The statistics include if the job printed with or without errors, the time required to print the job, the size (in bytes) of the job, the requested paper size and paper type, the total number of printed pages, and the number of copies requested.

Select Clear to delete all accumulated job statistics from the hard disk option. Clearing Job Accounting Stat displays until the process completes. See Clearing Job Accounting Stat on page 152 for more information.

Hex Trace Press Select to enter Hex Trace mode.

Hex Trace helps isolate the source of a print job problem. With Hex Trace selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not run.

To exit Hex Trace, turn the printer power Off (O), or reset the printer. To reset the printer, press Menu> or <Menu. JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select.

Job Menu Some JOB MENU menu items are available when the printer displays the Ready message and is idle since it is not accepting, formatting, or printing a job. Other menu items in JOB MENU are only available when the printer is busy processing or printing a job, when a printer message other than Ready displays, or when the printer is in Hex Trace mode.

59 Operator Panel Menus

Menu Item Values

Page 72 of the Lexmark M412 user manual — 60 Chapter 3: Using the Operator Panel and Menus
Page 72 · click to enlarge
Page 72

Job Menu

Cancel Job Press Select to cancel the current print job.

Cancel Job displays only when the printer is processing a print job.

CONFIDENTIAL JOB

Once a correct Personal Identification Number (PIN) is entered, the following values are available as second and third sub-menus. See “Entering a Personal Identification Number (PIN)” on page 111 for more information.

This menu item is not displayed in the JOB MENU until the printer has processed at least one Confidential Job.

PRINT A JOB

...

DELETE A JOB

...

PRINT COPIES

...

Note: In the sub-menu values listed above, the Username field is based on the username field in your driver. By default, this is the user name or user ID you type to log on to your operating system. You can change the name in this field to another name in the driver before you send the job. The Jobname field contains a title name for your file as defined by your application software when the job was sent. You cannot change this field. If one or both of the fields is empty, the name was not defined by the application. For example, if your last name is Smith and your file is called timesheet, the operator panel may display smith timesheet. The Username and Jobname fields are truncated to 16 characters.

When you create a Confidential Job, the printer formats your job and holds the job in memory. The printer delays the printing of your job until you enter a PIN assigned to the job. You enter the number through the operator panel. See “Entering a Personal Identification Number (PIN)” on page 111 for more information.

60 Chapter 3: Using the Operator Panel and Menus

Show 4 more labels / short text on this page
Menu Item Values · Enter PIN · Print All Jobs · Delete All Jobs
Page 73 of the Lexmark M412 user manual — 61 Operator Panel Menus
Page 73 · click to enlarge
Page 73

Job Menu (continued)

Once a valid PIN is entered, the operator panel displays:

CONFIDENTIAL JOB Print All Jobs

You have several print or delete options to choose from:

  • print all jobs
  • print a job
  • print copies
  • delete all jobs
  • delete a job

Press Menu> or <Menu until the menu item you need appears on the second line of the display.

Press Select.

While in the values for this menu item, the following button actions are possible:

  • Press Go to exit the selection and the menu group, and return to the previous screen.
  • Press Menu> or <Menu to choose the next or previous option in the list.
  • Press Return to exit the operation, but remain in the JOB MENU or to return to the previous screen after scrolling through a list of print jobs.

61 Operator Panel Menus

Menu Item Values · CONFIDENTIAL JOB (continued)

Page 74 of the Lexmark M412 user manual — 62 Chapter 3: Using the Operator Panel and Menus
Page 74 · click to enlarge
Page 74

Job Menu (continued)

If you press Select to choose this value, printing starts and the operator panel exits this operation.

All Confidential Jobs associated with your assigned PIN are printed.

The message Queuing Jobs displays. For more information, see “Queuing Jobs” on page 156.

PRINT A JOB

If you press Select to choose this value, a list of jobs available for printing is displayed. The first job is displayed on the second line.

PRINT A JOB

All Confidential Jobs associated with your assigned PIN are listed. Use Menu> or <Menu to scroll through the list of available jobs.

PRINT A JOB

See the note on page 60 for an explanation of Username and Jobname.

Press Menu> or <Menu to scroll to the job you want to print. When the job is on the second line of the display, press Select to mark the job for printing. An asterisk (*) appears to mark the job for printing. You may select additional jobs to print by marking them with an asterisk.

When a job has been marked for printing, the job is removed from the list of available print jobs in the DELETE A JOB list. See DELETE A JOB on page 63 for more information.

Press Return until you exit the menus or press Go to exit the menus. The message Queuing Jobs displays; however, the message Queuing and Deleting Jobs displays if you previously selected some print jobs for deletion. Once the printer exits the menus and returns to an online state, the job starts printing. For more information, see Queuing Jobs and Queuing and Deleting Jobs on page 156.

62 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · CONFIDENTIAL JOB (continued) · Print All Jobs

Page 75 of the Lexmark M412 user manual — 63 Operator Panel Menus
Page 75 · click to enlarge
Page 75

Job Menu (continued)

If you press Select to choose this value, the message Delete All Jobs. Go/Stop? displays. You have one chance to stop the deletion of all the confidential jobs associated with your PIN.

Press Stop if you do not want to delete all jobs. The operator panel returns to the following screen, and you may choose to exit the CONFIDENTIAL JOB menu item or scroll to another value using Menu> or <Menu.

CONFIDENTIAL JOB Delete All Jobs

Press Go to delete all jobs. The message Deleting Jobs displays. The jobs are deleted and the printer exits the menus.

DELETE A JOB

If you press Select to choose this value, a list of jobs held in printer memory is displayed as shown. The first job is displayed on the second line.

DELETE A JOB

All Confidential Jobs associated with your assigned PIN are listed. Use Menu> or <Menu to scroll through the list of available jobs.

DELETE A JOB

See the note on page 60 for an explanation of Username and Jobname.

Press Menu> or <Menu to scroll to the job you want to delete. When the job is on the second line of the display, press Select to mark a job for deletion. An asterisk (*) appears to mark the job for deletion. You may select additional jobs to delete by marking them with an asterisk.

When a job has been marked for deletion, the job is removed from the list of available print jobs in the PRINT A JOB list and the PRINT COPIES list. See PRINT A JOB on page 62 and PRINT COPIES on page 64 for more information.

Press Return until you exit the menus or press Go to exit the menus. Once the printer exits the menus and returns to an online state, the jobs you selected are deleted. The message Deleting Jobs displays; however, the message Queuing and Deleting Jobs displays if you previously selected some jobs to print. For more information, see Deleting Jobs and Queuing and Deleting Jobs on page 153.

63 Operator Panel Menus

Menu Item Values · CONFIDENTIAL JOB (continued) · Delete All Jobs

Page 76 of the Lexmark M412 user manual — 64 Chapter 3: Using the Operator Panel and Menus
Page 76 · click to enlarge
Page 76

Job Menu (continued)

PRINT COPIES

If you press Select to choose this value, a list of jobs held in printer memory is displayed as shown. The first job is displayed on the second line.

PRINT COPIES

All Confidential Jobs associated with your assigned PIN are listed. Use Menu> or <Menu to scroll through the list of available jobs.

PRINT COPIES

See the note on page 60 for an explanation of Username and Jobname.

You may select one or more jobs to print and you may change the number of copies for each job to be printed.

Press Menu> or <Menu to scroll to the one job you want to print. When the job is on the second line of the display, press Select.

The following prompt displays:

The setting for the current number of copies is indicated by the asterisk (*). Press Menu> or <Menu to increase or decrease the number of copies as specified by the x value. You may choose to print from 1 to 999 copies of a single job at a time.

Press Select to save the setting for the number of copies you need. The Saved message displays and then the list of jobs displays. An asterisk (*) appears beside the job name to indicate it is selected for printing. You may select other jobs to print and change the number of copies required.

When a job has been marked for printing, the job is removed from the list of available print jobs in the DELETE A JOB list. See DELETE A JOB on page 63 for more information.

When you finish making selections and change the number of copies, press Return until you exit the menus or press Go to exit the menus. The message Queuing Jobs displays; however, the message Queuing and Deleting Jobs displays if you previously selected some jobs for deletion. Once the printer exits the menus and returns to an online state, the remaining copies print. Once all copies are printed, the job is deleted from printer memory. For more infor- mation, see Queuing Jobs and Queuing and Deleting Jobs on page 156.

64 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · CONFIDENTIAL JOB (continued) · Copies =x*

Page 77 of the Lexmark M412 user manual — 65 Operator Panel Menus
Page 77 · click to enlarge
Page 77

Job Menu (continued)

HELD JOBS

This menu item is not displayed in the JOB MENU until the printer has processed at least one Repeat Print, Reserve Print, or Verify Print job.

PRINT A JOB

...

DELETE A JOB

...

PRINT COPIES

...

Note: In the sub-menu values listed above, the Username field is based on the username field in your driver. By default, this is the user name or user ID you type in to log on to your operating system. You can change the name in this field to another name in the driver before you send the job. The Jobname field contains a title name for your file as defined by your application software when the job was sent. You cannot change this field. If one or both of the fields is empty, the name was not defined by the application. For example, if your last name is Smith and your file is called timesheet, the operator panel may display smith timesheet. The Username and Jobname fields are truncated to 16 characters.

Unlike a Confidential Job, you do not enter a PIN to access the values once you enter the HELD JOBS menu item.

When you create a Repeat Print job, the job formats and prints, but the printer stores the job in memory so you can print additional copies of the job at a later time. As long as the job remains stored in memory, you may print additional copies. Repeat Jobs are automatically deleted when the printer requires extra memory to process additional jobs or when the number of Repeat Jobs stored exceeds the value of the set limit for Print and Hold Repeat Job Limit. For more information about this setting, refer to the Technical Reference.

When you create a Reserve Print job, the job formats, but does not print. The printer stores the job in memory so you can print the job at a later time. All pages in the job are held in memory until you activate printing by using the operator panel to select Print All Jobs or PRINT A JOB. Reserve Print jobs are not deleted from memory when the job prints. To delete a Reserve Print job, you must request DELETE A JOB using the operator panel.

65 Operator Panel Menus

Menu Item Values · Print All Jobs · Delete All Jobs

Page 78 of the Lexmark M412 user manual — 66 Chapter 3: Using the Operator Panel and Menus
Page 78 · click to enlarge
Page 78

Job Menu (continued)

When you create a Verify Print job, the job formats, and one copy of the job prints. Additional requested copies are held in printer memory. You specify the number of copies you want when you send the job from the printer driver. This allows you to examine the first copy to be sure it is satisfactory before you print the other copies.

If the job is unsatisfactory, you would not want the other copies to print. Select the DELETE A JOB value, and select the job to delete it. See DELETE A JOB on page 68 for more information.

To print the remaining copies, you can:

  • Change the number of remaining copies to print. Select PRINT COPIES . Select the specific job. At the Copies prompt, change the number of copies to print from the number set in the printer driver and press Select . Press Return until you exit the menus or press Go to exit the menus. Once the printer exits the menus and returns to an online state, the remaining copies print. Once all copies are printed, the job is deleted from printer memory. For more information, see PRINT COPIES on page 69.
  • Print the number of copies set in the printer driver. Select PRINT A JOB . Select the specific job. The remaining copies print. Once all copies are printed, the job is deleted from printer memory. For more information, see PRINT A JOB on page 67.

Once you select HELD JOBS, the operator panel displays:

HELD JOBS Print All Jobs

You have several print or delete options to choose from:

  • print all jobs
  • print a job
  • print copies
  • delete all jobs
  • delete a job

Press Menu> or <Menu until the menu item you need appears on the second line of the display.

Press Select.

While in the values for this menu item, the following button actions are possible:

  • Press Go to exit the selection, the menu group, and return to the previous screen.
  • Press Menu> or <Menu to choose the next or previous option in the list.
  • Press Return to exit the operation, but remain in the JOB MENU or to return to the previous screen after scrolling through a list of print jobs.

66 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · HELD JOBS (continued)

Page 79 of the Lexmark M412 user manual — 67 Operator Panel Menus
Page 79 · click to enlarge
Page 79

Job Menu (continued)

If you press Select to choose this value, printing starts and the operator panel exits this operation.

All Repeat Print, Reserve Print, and Verify Print jobs are printed.

The message Queuing Jobs displays. For more information, see “Queuing Jobs” on page 156.

PRINT A JOB

If you press Select to choose this value, a list of jobs available for printing is displayed. The first job is displayed on the second line.

PRINT A JOB

All Repeat Print, Reserve Print, and Verify Print jobs are listed. Use Menu> or <Menu to scroll through the list of available jobs.

PRINT A JOB

See the note on page 65 for an explanation of Username and Jobname.

Press Menu> or <Menu to scroll to the one job you want to print. When the job is on the second line of the display, press Select to mark a job for printing. An asterisk (*) appears to mark the job for printing. You may select additional jobs to print by marking them with an asterisk.

When a job has been marked for printing, the job is removed from the list of available print jobs in the DELETE A JOB list. See DELETE A JOB on page 68 for more information.

Press Return until you exit the menus or press Go to exit the menus. The message Queuing Jobs displays; however, the message Queuing and Deleting Jobs displays if you previously selected some jobs for deletion. Once the printer exits the menus and returns to an online state, the jobs you selected start printing. For more information, see Queuing Jobs and Queuing and Deleting Jobs on page 156.

67 Operator Panel Menus

Menu Item Values · HELD JOBS (continued) · Print All Jobs

Page 80 of the Lexmark M412 user manual — 68 Chapter 3: Using the Operator Panel and Menus
Page 80 · click to enlarge
Page 80

Job Menu (continued)

If you press Select to choose this value, the message Delete All Jobs. Go/Stop? displays so you have one chance to stop the deletion of all the print jobs you have sent.

Press Stop if you do not want to delete all jobs. The operator panel returns to the following screen, and you may choose to exit the CONFIDENTIAL JOB menu item or scroll to another value using Menu> or <Menu.

CONFIDENTIAL JOB Delete All Jobs

Press Go to delete all jobs. The message Deleting Jobs displays. The jobs are deleted and the printer exits the menus.

DELETE A JOB

If you press Select to choose this value, a list of jobs held in printer memory is displayed as shown. The first job is displayed on the second line.

DELETE A JOB

All Repeat Print, Reserve Print, and Verify Print jobs are listed. Use Menu> or <Menu to scroll through the list of available jobs.

DELETE A JOB

See the note on page 65 for an explanation of Username and Jobname.

Press Menu> or <Menu to scroll to the one job you want to delete. When the job you want to delete is on the second line of the display, press Select to mark a job for deletion. An asterisk (*) appears to mark the job for deletion. You may select additional jobs to delete by marking them with an asterisk.

When a job has been marked for deletion, the job is removed from the list of available jobs in the PRINT A JOB list and the PRINT COPIES list. See PRINT A JOB on page 67 and PRINT COPIES on page 69 for more information.

Press Return until you exit the menus or press Go to exit the menus. Once the printer exits the menus and returns to an online state, the job is deleted. The message Deleting Jobs displays; however, the message Queuing and Deleting Jobs displays if you previously selected some jobs to print. For more information, see Deleting Jobs and Queuing and Deleting Jobs on page 153.

68 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · HELD JOBS (continued) · Delete All Jobs

Page 81 of the Lexmark M412 user manual — 69 Operator Panel Menus
Page 81 · click to enlarge
Page 81

Job Menu (continued)

PRINT COPIES

If you press Select to choose this value, a list of jobs held in printer memory is displayed as shown. The first job is displayed on the second line.

PRINT COPIES

All Repeat Print, Reserve Print, and Verify Print jobs are listed. Use Menu> or <Menu to scroll through the list of available jobs.

PRINT COPIES

See the note on page 65 for an explanation of Username and Jobname.

You may select one or more jobs to print and you may change the number of copies for each job to be printed.

Press Menu> or <Menu to scroll to the job you want to print. When the job is on the second line of the display, press Select.

The following prompt displays:

The setting for the current number of copies is indicated by the asterisk (*). Press Menu> or <Menu to increase or decrease the number of copies as specified by the x value. You may choose to print from 1 to 999 copies of a single job at a time.

Press Select to save the setting for the number of copies you need. The Saved message displays and then the list of jobs displays. There is now an asterisk beside the job name to indicate it is selected for printing. You may select other jobs to print and change the number of copies required.

When a job has been marked for printing, the job is removed from the list of available jobs in the DELETE A JOB list. See DELETE A JOB on page 68 for more information.

When you are finished making selections and changing the number of copies, press Return until you exit the menus or press Go to exit the menus. The message Queuing Jobs displays; however, the message Queuing and Deleting Jobs displays if you previously selected some jobs for deletion. Once the printer exits the menus and returns to an online state, the remaining copies print. For more information, see Queuing Jobs and Queuing and Deleting on page 156.

69 Operator Panel Menus

Menu Item Values · HELD JOBS (continued) · Copies =x*

Page 82 of the Lexmark M412 user manual — 70 Chapter 3: Using the Operator Panel and Menus
Page 82 · click to enlarge
Page 82

Job Menu (continued)

Reset Printer Press Select to reset the printer.

When you select Reset Printer, the printer resets to the user default setting for each menu item. All downloaded resources (fonts, macros, symbol sets) in printer memory (RAM) are deleted. All data on the currently selected host interface is deleted from the interface link buffer. All Print and Hold jobs are deleted.

Print Buffer Press Select to print any data stored in the print buffer.

This menu item is only available when you enter the JOB MENU while the Waiting message is displayed. The Waiting state occurs if an incomplete job is sent to the printer or if an ASCII job is being printed. Examples include sending a print screen command from your host computer or copying a DOS file.

70 Chapter 3: Using the Operator Panel and Menus

Menu Item Values

Page 83 of the Lexmark M412 user manual — 71 Operator Panel Menus
Page 83 · click to enlarge
Page 83

Quality Menu Use the QUALITY MENU to change settings affecting the quality of the printed characters and images.

Quality Menu

Print Resolution 300 dpi 600 dpi* 1200 Image Q

The Print Resolution setting defines the number of dots printed per inch (dpi). The higher the setting, the sharper the clarity of printed characters and graphics.

If your print jobs are mostly text, select 600 dpi for the highest quality output. Select 1200 Image Q (1200 Image Quality) when your job contains bitmapped images, such as scanned photos or some business graphics, that will benefit from enhanced line screening.

Toner Darkness 1 2 3 4 5 6 7 8* 9 10

Use the Toner Darkness menu item to lighten or darken the image appearance in your print jobs and get the most from your toner supply.

If you want finer line width, higher definition in graphics, and lighter gray-scale images, set Toner Darkness to 6 or 7.

If you want a bolder line width, emphasis in graphics, or darker gray-scale images, set Toner Darkness to 9 or 10. Use the 10 value to emphasize line width, produce the boldest text, and the darkest images.

If you want to help conserve the printer toner supply, use the 1 to 5 values.

71 Operator Panel Menus

Menu Item Values · *Factory default

Page 84 of the Lexmark M412 user manual — 72 Chapter 3: Using the Operator Panel and Menus
Page 84 · click to enlarge
Page 84

Quality Menu (continued)

When you first enter Toner Darkness, the operator panel displays:

Toner Darkness =8 - v..+*

A minus sign (-) at the left end of the string of periods indicates you are scrolling to the lower numbers in the string. A plus sign (+) at the right end of the string of periods indicates you are scrolling to the higher numbers in the string. If you decide to change the setting to 6, for example, use <Menu to scroll back to the 6.

Toner Darkness =6 - v.|..+

As you scroll backward toward the minus sign (-) indicating lower numbers, notice the v or arrow symbol moves on the operator panel as you press the <Menu button. It now appears in place of the sixth period. Notice the numeral 6 displays next to the equal sign to indicate your selection. A vertical bar (|) indicates the factory default of 8. The vertical bar remains at 8 unless 8 is selected. Then, the arrow covers the vertical bar.

Press Select to select 6 as your current setting. The Saved message displays.

When printed characters appear to have jagged or uneven edges, set PQET (Print Quality Enhancement Technology) to On to improve the print quality of your text and make the characters appear smoother.

Use the PictureGrade™menu item to improve the quality of gray-scale printing at 300 and 600 dpi resolutions in PostScript 3 emulation.

If you select Off, the printer uses the standard screening parameters. If you select On, different default screening parameters are used to improve the print quality of graphics.

72 Chapter 3: Using the Operator Panel and Menus

Show 5 more labels / short text on this page
Menu Item Values · Toner Darkness (continued) · PQET Off On* · PictureGrade Off On* · *Factory default
Page 85 of the Lexmark M412 user manual — 73 Operator Panel Menus
Page 85 · click to enlarge
Page 85

Setup Menu Use the SETUP MENU to configure a variety of printer features.

Setup Menu

Printer Language PCL Emulation* PS Emulation

The printer language defines how the computer communicates with the printer. Your computer uses printer languages, such as PCL emulation and PostScript 3 emulation, to send print data to the printer. Setting a printer language as the default does not prevent the software appli- cation from sending print jobs that use the other printer language.

Power Saver Disabled 1…120 (20*) [Optra M410] 1…240 (15*) [Optra M412]

The Power Saver menu item lets you reduce power usage when the printer is idle by deter- mining the length of time (in minutes) the printer waits after a job is printed before it goes to a reduced power state.

If you have selected a Power Saver value, the Power Saver message replaces the Ready message and becomes the new printer default when the printer is in a Ready state. Both messages indicate the printer is ready to receive jobs.

If your printer is in constant use, select a high setting, such as 120. Under most circum- stances, this keeps the printer ready to print with minimum warm-up time. However, a high setting also uses more energy.

Set Power Saver to 1 to put the printer in Power Saver mode one minute after it finishes a print job. This uses much less energy, but requires more warm-up time for the printer. If your printer shares an electrical circuit with room lighting and you notice lights flickering, you may want to set Power Saver to 1.

If you want a balance between energy consumption and a shorter warm-up period, select a Power Saver value between 1 and 120 minutes or 1 and 240 minutes depending on your printer model.

Resource Save Off* On

The Resource Save setting determines what the printer does with downloaded resources, such as fonts and macros, if it receives a job that requires more memory than is available.

If Resource Save is set to On, the printer retains all permanent downloaded resources for all printer languages during language changes and printer resets. If the printer runs out of memory, Memory Full appears on the operator panel display.

If Resource Save is set to Off, the printer retains permanent downloaded resources only until memory is needed. Then it deletes those resources stored for the inactive printer language.

73 Operator Panel Menus

Menu Item Values · *Factory default

Page 86 of the Lexmark M412 user manual — 74 Chapter 3: Using the Operator Panel and Menus
Page 86 · click to enlarge
Page 86

Setup Menu (continued)

Download Target RAM* Flash Disk

The Download Target menu item specifies the storage location for downloaded resources, such as fonts and macros.

Storing downloaded resources in flash memory or hard disk is permanent storage rather than the temporary storage that RAM provides. You can add resources to flash memory or to the hard disk until the option is full. Use your software application or the printer Toolkit to download resources to the printer.

The Download Target menu item only displays if a formatted flash memory option or hard disk option is installed in the printer and is not defective or Read/Write or Write protected. 51 Defective Flash or 61 Defective Disk may display when the printer is turned on, or during format and write operations. See 51 Defective Flash on page 161 or 61 Defective Disk on page 165 for more information.

Disk does not display for Download Target if Job Buffer Size is set to 100%. See Job Buffer Size on page 77 for more information.

If neither option is installed, Download Target does not display and all downloaded resources are automatically stored in printer memory (RAM).

Print Timeout Disabled 1…255 (90*)

The Print Timeout setting determines the time (in seconds) the printer waits before printing the last page of a print job that does not end with a command to print the page. The print timeout counter does not start until the Waiting message displays.

When a print timeout occurs, the printer stores the page in the print buffer.

Select Disabled to turn Print Timeout off. When Print Timeout is disabled, the printer does not print the last page of a print job until one of the following occurs:

  • The printer receives enough information to fill the page.
  • The printer receives a Form Feed command.
  • You select Print Buffer from the JOB MENU . See page 70 for more information.

Wait Timeout Disabled 15…65535 (40*)

The Wait Timeout setting determines the amount of time (in seconds) the printer waits to receive additional bytes of data from the computer. When this timeout expires, the print job is canceled.

Select Disabled to turn Wait Timeout off.

Wait Timeout is only available when using PostScript 3 emulation. The setting has no effect on PCL emulation print jobs.

74 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 87 of the Lexmark M412 user manual — 75 Operator Panel Menus
Page 87 · click to enlarge
Page 87

Setup Menu (continued)

Auto Continue Disabled* 5…255

Set Auto Continue to a value between 5 seconds and 255 seconds to have the printer continue printing after it detects one of the following errors:

34 Short Paper 35 Res Save Off Deficient Memory 37 Insufficient Collation Area 37 Insufficient Defrag Memory 37 Insufficient Memory 38 Memory Full 39 Complex Page 51 Defective Flash 52 Flash Full 53 Unformatted Flash 54 Serial Option 1 Error 54 Std Par ENA Connection Lost 54 Par 1 ENA Connection Lost 54 Ser 1 Fax Connection Lost 54 Network 1 Software Error 55 Insufficient Fax Buffer 56 Serial Port 1 Disabled 56 Std Parallel Port Disabled 56 Parallel Port 1 Disabled 58 Too Many Flash Options 61 Defective Disk 62 Disk Full 63 Unformatted Disk Print Jobs on Disk? Go/Stop?

If one of these errors occurs and Auto Continue is set to Disabled, the printer stops and waits for operator intervention. When Auto Continue is set to a numerical value, the printer waits for the specified length of time and then automatically resumes processing.

This setting is also used as a timer. After an inactive period in the menus, the printer automat- ically exits the menus and returns to the Ready state.

Jam Recovery On Off Auto*

When Jam Recovery is set to Off, the printer does not reprint a page that has jammed.

When Jam Recovery is set to On, the printer keeps the image for a printed page until the printer signals that the page has successfully exited the printer. The printer reprints all jammed pages.

If Jam Recovery is set to Auto, the printer keeps the image and reprints the page unless the memory required to hold the page is needed for other printer tasks.

75 Operator Panel Menus

Menu Item Values · *Factory default

Page 88 of the Lexmark M412 user manual — 76 Chapter 3: Using the Operator Panel and Menus
Page 88 · click to enlarge
Page 88

Setup Menu (continued)

Page Protect Off* On

Set Page Protect to On to make sure an entire page is processed before it is printed. This may be helpful if you are having trouble printing a page properly because of complex page errors. If you still cannot print the page, your printer may not have enough memory to process the page. You may have to reduce the size and number of fonts on the page, or increase the installed printer memory.

For most print jobs, you do not need to set Page Protect to On. When Page Protect is set to On, printing may be slowed.

Print Area Normal* Whole Page

The Print Area setting lets you modify the PCL formatting area and the printer physical print area. Refer to the Technical Reference for more information about printable areas.

Display Language English* French German Italian Spanish Danish Norwegian Dutch Swedish Portuguese Finnish

The following languages appear as a menu item value on some operator panels:

Japanese Russian Polish Hungarian Turkish Czech

The Display Language setting determines the language of the text that appears on the operator panel display.

76 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 89 of the Lexmark M412 user manual — 77 Operator Panel Menus
Page 89 · click to enlarge
Page 89

Setup Menu (continued)

Alarm Control Off Single* Continuous

If you want the printer alarm to sound any time the printer requires intervention, select Single or Continuous. If you select Single, the printer sounds three quick beeps to let you know operator intervention is required. If you select Continuous, the printer repeats the three beeps every ten seconds.

Select Off if you do not want the alarm to sound.

Job Buffer Size Disabled* 10…100%

If you have a hard disk option installed in your printer, you can allocate a portion of the available hard disk space for processing print jobs. The job is temporarily stored on the hard disk before being printed, usually freeing the host computer while the job prints.

The Job Buffer Size menu item lets you select the amount of hard disk space allocated to job buffering for all ports that have Job Buffering set to On. You can choose any 1% increment between 10% and 100%. You must select a Job Buffer Size before you can set the Job Buffering menu item On in the PARALLEL MENU or USB MENU. See Job Buffering on page 85 and on page 101 for more information.

The Job Buffer Size menu item only displays if the installed hard disk option is formatted and is not defective or Read/Write or Write protected. 61 Defective Disk may display when the printer is turned on, or during disk format and write operations. See 61 Defective Disk on page 165 for more information.

To password protect the hard disk option and use Job Buffering simultaneously, perform the following steps in order:

  • Set the Job Buffer Size for the hard disk option.
  • Download the files you want to the hard disk option.
  • Password protect the disk.

Refer to the Technical Reference for detailed information on how to password protect the hard disk option.

77 Operator Panel Menus

Menu Item Values · *Factory default

Page 90 of the Lexmark M412 user manual — 78 Chapter 3: Using the Operator Panel and Menus
Page 90 · click to enlarge
Page 90

Setup Menu (continued)

Job Accounting Off* On

If Job Accounting is set to On, the installed hard disk option stores statistical information about the most recent printer jobs. The statistics include whether the job printed with or without errors, the time required to print the job, the size (in bytes) of the job, the requested paper size and paper type, the total number of printed pages, and the number of copies requested.

To print a listing of all the accumulated statistics, select Print from the Job Acct Stat menu item in the UTILITIES MENU. See Job Acct Stat on page 59 for more information.

The Job Accounting menu item does not display if the installed disk option is defective or Read/Write or Write protected, or if Job Buffer Size is set to 100%. See Job Buffer Size on page 77 for more information.

Job Acct Limit Disabled 10…1000* (in increments of 1 job)

If a hard disk option is installed in your printer, you can use the hard disk to store statistical information about a specified number of jobs. The value you select from the Job Acct Limit menu item determines the number of jobs for which statistics are stored. Once you reach the job limit, statistics for the oldest job are deleted as new statistics are stored, maintaining statistics for the specified number of jobs.

If you select Disabled, the number of jobs for which statistics are stored is limited to the memory available on the hard disk.

The Job Acct Limit menu item does not display if the installed hard disk option is defective or Read/Write or Write protected, or if Job Buffer Size is set to 100%. See Job Buffer Size on page 77 for more information.

78 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 91 of the Lexmark M412 user manual — 79 Operator Panel Menus
Page 91 · click to enlarge
Page 91

PCL Emul Menu Use the PCL EMUL MENU to change printer settings that only affect jobs printed using the PCL emulation printer language.

PCL Emul Menu

Font Source Resident* Download Flash Disk All

The Font Source setting determines which fonts appear in the Font Name menu.

If a font source is not installed or does not contain any fonts, it is not listed as a value. Fonts are loaded and stored on the flash memory option.

See “Understanding Fonts” on page 231 for more information.

Font Name Font position and font name for all fonts in the selected font source (displays on both lines of the operator panel)

After you select a font source, choose the specific font from the Font Name menu item. The printer displays the font source abbreviation, font ID, and font name for each font. The font source abbreviation is R for resident, F for flash, K for disk, and D for download.

To print a font sample list showing all the fonts available for PCL emulation, see “Printing a Font Sample List” on page 242.

Point Size (only displays for PostScript or typographic fonts)

1…1008 (in increments of 0.25)

Point size refers to the height of the characters in the font. One point equals approximately 1/72 of an inch.

If you chose a scalable typographic font, you can select the point size for the font. You can select point sizes from 1 to 1008 in increments of 0.25 points. See “Pitch and Point Size” on page 232 for more information.

79 Operator Panel Menus

Show 4 more labels / short text on this page
Menu Item Values · (R0 Courier*) · (12*) · *Factory default
Page 92 of the Lexmark M412 user manual — 80 Chapter 3: Using the Operator Panel and Menus
Page 92 · click to enlarge
Page 92

PCL Emul Menu (continued)

Pitch (only displays for fixed or monospaced fonts)

0.08…100 (in increments of 0.01)

Pitch refers to the number of fixed-space characters in a horizontal inch of type.

If you chose a scalable monospaced font, you can select the font pitch. You can select a pitch from 0.08 to 100 characters per inch (cpi) in increments of 0.01 cpi. For non-scalable monospaced fonts, the pitch displays, but it cannot be changed. See “Pitch and Point Size” on page 232 for more information.

Symbol Set List of Symbol Set IDs and Symbol Set names (displays on both lines of the operator panel)

10U PC-8* (Country specific) 12U PC-850* (Country specific)

A symbol set is a set of alphabetic and numeric characters, punctuation, and special symbols used when printing with a selected font. Symbol sets support the different requirements for languages or specific applications, such as math symbols for scientific text. The printer displays only the symbol sets supported for the selected font name.

The Orientation setting determines how the printing is oriented on the page.

Select Portrait to print parallel to the short edge of the print material.

This is PORTRAIT orientation. This is PORTRAIT orientation. This is

Select Landscape to print parallel to the long edge of the print material.

This is LANDSCAPE orientation. This is LANDSCAPE orientation.

80 Chapter 3: Using the Operator Panel and Menus

Show 4 more labels / short text on this page
Menu Item Values · (10*) · Orientation Portrait* Landscape · *Factory default
Page 93 of the Lexmark M412 user manual — 81 Operator Panel Menus
Page 93 · click to enlarge
Page 93

PCL Emul Menu (continued)

Lines per Page 1…255

60* (Country specific) 64* (Country specific)

Use the Lines per Page menu item to change the number of lines that print on each page.

The Lines per Page setting can range from 1 to 255 lines per page. The printer sets the amount of space between each line (vertical line spacing) based on the Lines per Page, PAPER SIZE, and Orientation settings. Select the correct PAPER SIZE from the PAPER MENU and Orientation before setting Lines per Page. See PAPER SIZE on page 45 and Orientation on page 80 for more information.

A4 Width 198 mm* 203 mm

The A4 Width menu item lets you select the width of the logical page for A4 paper.

When you select 198 mm, the width of the logical page is compatible with that of the Hewlett-Packard LaserJet 5 printer. When you select 203 mm, the width of the logical page is wide enough to print eighty 10-pitch characters.

81 Operator Panel Menus

Menu Item Values · *Factory default

Page 94 of the Lexmark M412 user manual — 82 Chapter 3: Using the Operator Panel and Menus
Page 94 · click to enlarge
Page 94

PCL Emul Menu (continued)

TRAY RENUMBER Assign MP Feeder Assign Tray 1 Assign Tray 2 Assign Man Paper Assign Man Env

Each of the above menu items supports the following three values:

Off* 0 ... 199 None

VIEW FACTORY DEF Restore Defaults

Only installed paper sources display on the operator panel as values. However, you may set TRAY RENUMBER to uninstalled sources.

The TRAY RENUMBER menu item lets you configure your printer to work with printer drivers or applications that use different source assignments to request a given input source.

Select Off to use the factory default paper source assignments.

Select a numeric value (0 ... 199) to assign a custom value to a paper source.

Select VIEW FACTORY DEF to view the factory default values assigned to each paper source.

In the Restore Defaults menu item, select Yes to return all tray assignments to factory default values.

See “Paper Sources and Sizes” on page 116 for information on available paper sources for your printer.

Refer to the Technical Reference for more information about assigning source numbers.

Auto CR after LF Off* On

The Auto CR after LF setting determines if the printer automatically performs a carriage return after a line feed control command.

Auto LF after CR Off* On

The Auto LF after CR setting determines if the printer automatically performs a line feed after a carriage return control command.

82 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · Yes No · *Factory default

Page 95 of the Lexmark M412 user manual — 83 Operator Panel Menus
Page 95 · click to enlarge
Page 95

PostScript Menu Use the POSTSCRIPT MENU to change settings that only affect jobs printed using the PostScript 3 emulation printer language.

PostScript Menu

Print PS Error Off* On

Select On to print PostScript 3 emulation errors. If an error occurs, the job stops processing, the error message prints, and the printer discards the job.

If Print PS Error is set to Off and an error occurs, the job is discarded but no error message prints.

Font Priority Resident* Flash / Disk

The Font Priority menu item only displays if a flash memory or disk option is installed, formatted and is not defective, Read/Write or Write protected and Job Buffer Size is not set to 100%. See Job Buffer Size on page 77 for more information.

83 Operator Panel Menus

Menu Item Values · *Factory default

Page 96 of the Lexmark M412 user manual — 84 Chapter 3: Using the Operator Panel and Menus
Page 96 · click to enlarge
Page 96

Parallel Menu Use the PARALLEL MENU to change settings affecting jobs sent to the printer through the parallel interface con- nection. PARALLEL MENU displays as a standard feature or as an option, and appears as one of the following:

  • STD PARALLEL
  • PARALLEL OPT 1

PARALLEL OPT 1 is only available if a parallel/USB interface option card is installed. The following menu items set the configuration of the parallel interface connec- tion.

Parallel Menu

PCL SmartSwitch Off On*

If PCL SmartSwitch is set to On, the printer examines the data on the parallel interface connection and selects PCL emulation if the data indicates that is the printer language.

If both PCL SmartSwitch and PS SmartSwitch are set to Off, the printer uses the language specified in the Printer Language menu as the default. If only one SmartSwitch setting is set to Off, the printer uses the language that has its SmartSwitch setting set to On as the default.

PS SmartSwitch Off On*

If PS SmartSwitch is set to On, the printer examines the data on the parallel interface connection and selects PostScript 3 emulation if the data indicates that is the printer language.

If both PCL SmartSwitch and PS SmartSwitch are set to Off, the printer uses the language specified in the Printer Language menu as the default. If only one SmartSwitch setting is set to Off, the printer uses the language that has its SmartSwitch setting set to On as the default.

84 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 97 of the Lexmark M412 user manual — 85 Operator Panel Menus
Page 97 · click to enlarge
Page 97

Parallel Menu (continued)

NPA Mode On Off Auto*

NPA is a mode of bidirectional communication that follows the conventions defined in Network Printing Alliance Protocol, A Printer/Host Control Specification Developed by the NPA. NPA mode requires special processing of the print data.

If NPA Mode is set to On, the data received must be in NPA format. If not, it is rejected as bad data. If NPA Mode is set to Off, the printer does not perform any NPA processing. If NPA Mode is set to Auto, the printer examines the data to determine the format and then processes it in either format.

The NPA Mode setting in the PARALLEL MENU applies only to the parallel interface connection.

Parallel Buffer Disabled Auto* 3K to maximum size allowed

You can configure the size of the parallel input buffer to meet the requirements of your system.

The maximum size available for modification depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the parallel buffer size, you can disable or reduce the size of the serial, network, infrared, LocalTalk, and Universal Serial Bus (USB) buffers.

Choose Auto to let the printer calculate a buffer size proportional to the total amount of available printer memory. In most cases, Auto is the recommended setting.

Job Buffering Off* On

Job buffering lets you delay processing of a print job. The job is temporarily stored on a hard disk option before being printed, usually freeing the host computer while the job prints.

The Job Buffering menu item only displays if the installed hard disk option is formatted and is not defective, Read/Write or Write protected, and if Job Buffer Size is not set to Disabled. See Job Buffer Size on page 77 for more information. 61 Defective Disk may display when the printer is turned on, or during disk format and write operations. See 61 Defective Disk on page 165 for more information.

If Job Buffering is set to On, print jobs are buffered to the hard disk option. If Job Buffering is set to Off, print jobs are not buffered.

85 Operator Panel Menus

Menu Item Values · *Factory default

Page 98 of the Lexmark M412 user manual — 86 Chapter 3: Using the Operator Panel and Menus
Page 98 · click to enlarge
Page 98

Parallel Menu (continued)

Advanced Status Off On*

If Advanced Status is set to On, bidirectional communication is enabled through the parallel interface.

You can select Standard or Fastbytes protocol for the parallel interface. Fastbytes is compatible with most existing parallel interface implementations. Use Standard only if you experience parallel interface problems.

Refer to the Technical Reference for more information about the parallel interface.

Honor Init Off* On

The Honor Init setting determines whether the printer honors hardware initialization requests from the computer. The computer requests initialization by activating the INIT signal on the parallel interface. Many personal computers activate the INIT signal each time the computer is turned on and off.

Parallel Mode 1 Off On*

The Parallel Mode 1 setting controls the pull up resistors on the parallel port signals. It is useful for personal computers that have open collector outputs on the parallel port signals.

Set Parallel Mode 1 to On to disable the resistors or to Off to enable the resistors.

Parallel Mode 2 Off On*

The Parallel Mode 2 setting determines if the parallel port data is sampled on the leading or trailing edge of strobe.

If Parallel Mode 2 is set to On, the parallel port data is sampled on the leading edge of strobe.

If Parallel Mode 2 is set to Off, the parallel port data is sampled on the trailing edge of strobe.

86 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · Protocol Standard Fastbytes* · *Factory default

Page 99 of the Lexmark M412 user manual — 87 Operator Panel Menus
Page 99 · click to enlarge
Page 99

Serial Menu Use the SERIAL MENU to change settings affecting jobs sent to the printer through the serial interface port.

SERIAL MENU displays as an option, and appears as SERIAL OPTION 1. SERIAL OPTION 1 is only available if the Tri-Port interface option card is installed and Fax Port is set to disabled.

Serial Menu

PCL SmartSwitch Off On*

If PCL SmartSwitch is set to On, the printer examines the data on the serial interface connection and selects PCL emulation if the data indicates that is the printer language.

If both PCL SmartSwitch and PS SmartSwitch are set to Off, the printer uses the language specified in the Printer Language menu as the default. If only one SmartSwitch setting is set to Off, the printer uses the language that has its SmartSwitch setting set to On as the default.

PS SmartSwitch Off On*

If PS SmartSwitch is set to On, the printer examines the data on the serial interface connection and selects PostScript 3 emulation if the data indicates that is the printer language.

If both PCL Smartswitch and PS Smartswitch are set to Off, the printer uses the language specified in the Printer Language menu as the default. If only one SmartSwitch setting is set to Off, the printer uses the language that has its SmartSwitch setting set to On as the default.

NPA Mode On Off Auto*

NPA is a mode of bidirectional communication that follows the conventions defined in Network Printing Alliance Protocol, A Printer/Host Control Specification Developed by the NPA. NPA mode requires special processing of the print data.

If NPA Mode is set to On, the data received must be in NPA format. If not, it is rejected as bad data. If NPA Mode is set to Off, the printer does not perform any NPA processing. If NPA Mode is set to Auto, the printer examines the data to determine the format and then processes it in either format.

The NPA Mode setting in the SERIAL MENU applies only to the serial interface connection.

87 Operator Panel Menus

Menu Item Values · *Factory default

Page 100 of the Lexmark M412 user manual — 88 Chapter 3: Using the Operator Panel and Menus
Page 100 · click to enlarge
Page 100

Serial Menu (continued)

Serial Buffer Disabled Auto* 3K to maximum size allowed

You can configure the size of the serial input buffer to meet the requirements of your system. If the limited size of the serial buffer is preventing you from continuing work in your software application each time you send a job to the printer, you may want to increase the buffer size.

The maximum size depends on the amount of memory in your printer, the size of the other link buffers and whether the Resource Save setting is set to On or Off. To maximize the range for the serial buffer size, you can disable or reduce the size of the parallel, infrared, LocalTalk, and USB buffers. Choose Auto to let the printer calculate a buffer size proportional to the total amount of available printer memory. In most cases, Auto is the recommended setting.

RS-232/RS-422 RS-232* RS-422

Choose the serial communication configuration for your printer. Selecting RS-422 automat- ically sets Serial Protocol to XON/XOFF.

RS-422 Polarity Normal* Reverse

Select Normal or Reverse polarity.

This setting is only available if the serial communication configuration is set to RS-422. To do this, select SERIAL MENU, SERIAL OPTION 1, RS-232/RS-422, and RS-422.

Serial Protocol DTR* (hardware handshaking) DTR/DSR (hardware handshaking) XON/XOFF (software handshaking) XON/XOFF/DTR (combined handshaking) XON/XOFF/DTR/DSR (combined handshaking)

Handshaking is the exchange of predetermined signals when a connection is established.

This printer supports hardware handshaking, software handshaking, and combined hardware and software handshaking.

Refer to the Technical Reference for more information about serial interface.

Robust XON Off* On

Robust XON only applies to the serial port if Serial Protocol is set to XON/XOFF.

When Robust XON is set to On, the printer sends a continuous stream of XONs to the host computer to indicate that the serial port is ready to receive more data.

88 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 101 of the Lexmark M412 user manual — 89 Operator Panel Menus
Page 101 · click to enlarge
Page 101

Serial Menu (continued)

Baud 1200 2400 4800 9600* 19200 38400 57600 115200

This setting lets you select the rate at which data is being sent to or from your computer. Refer to the Technical Reference for information about the range of baud values.

Data Bits 7 8*

This setting lets you select the number of data bits that are sent in each transmission frame. Refer to the Technical Reference for more information about data bits.

89 Operator Panel Menus

Menu Item Values · *Factory default

Page 102 of the Lexmark M412 user manual — 90 Chapter 3: Using the Operator Panel and Menus
Page 102 · click to enlarge
Page 102

Serial Menu (continued)

Parity Even Odd None* Ignore

This setting lets you select the parity for serial input and output data frames.

Even The port expects to receive data frames with an even number of logical 1’s per byte. The port transmits XOFF and XON with even parity. If the port detects a parity error, the port sends an inverted question mark to the printer instead of the character sent by the host system. Odd The port expects to receive data frames with an odd number of logical 1’s per byte. The printer transmits XOFF and XON with odd parity. If the printer detects a parity error, the port sends X'5F' to the printer instead of the character sent by the host system. None The port expects no parity bit when it receives data. The port transmits XON and XOFF without parity bits. Ignore The port expects a parity bit when the port receives a data frame. The port

ignores the parity bit. The port uses even parity when it transmits XON and XOFF.

Refer to the Technical Reference for more information about parity.

Honor DSR (only available if configured for RS-232)

Honor DSR determines if the printer uses the Data Set Ready (DSR) signal. DSR is one of the handshaking signals for most serial interface cables. If Honor DSR is set to Off, data received by the serial interface is seen as valid data. If Honor DSR is set to On, only data received while the DSR signal is in high condition is treated as valid data.

The serial interface uses DSR to distinguish data sent by the computer from data created by electrical noise in the serial cable. This electrical noise can cause stray characters to print.

Set Honor DSR to On to prevent stray characters from printing.

90 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · Off* On · *Factory default

Page 103 of the Lexmark M412 user manual — 91 Operator Panel Menus
Page 103 · click to enlarge
Page 103

Network Menu Use the NETWORK MENU to change settings affecting jobs sent to the printer through the network port.

NETWORK MENU displays as an option, and appears as NETWORK OPTION 1. NETWORK OPTION 1 is only available if an optional print server is installed in your printer.

Network Menu

PCL SmartSwitch Off On*

If PCL SmartSwitch is set to On, the printer examines the data on the network interface connection and selects PCL emulation if the data indicates that is the printer language.

If both PCL SmartSwitch and PS SmartSwitch are set to Off, the printer uses the language specified in the Printer Language menu as the default. If only one SmartSwitch setting is set to Off, the printer uses the language that has its SmartSwitch set to On as the default.

PS SmartSwitch Off On*

If PS SmartSwitch is set to On the printer examines the data on the network interface connection and selects PostScript 3 emulation if the data indicates that is the printer language.

If both PCL SmartSwitch and PS SmartSwitch are set to Off, the printer uses the language specified in the Printer Language menu as the default. If only one SmartSwitch setting is set to Off, the printer uses the language that has its SmartSwitch setting set to On as the default.

NPA Mode Off Auto*

NPA is a mode of bidirectional communication that follows the conventions defined in Network Printing Alliance Protocol, A Printer/Host Control Specification Developed by the NPA. NPA mode requires special processing of the print data.

If NPA Mode is set to On, the data received must be in NPA format. If not, it is rejected as bad data. If NPA Mode is set to Off, the printer does not perform any NPA processing. If NPA Mode is set to Auto, the printer examines the data to determine the format and then processes it in either format.

The NPA Mode setting in the NETWORK MENU applies only to the network interface connection.

91 Operator Panel Menus

Menu Item Values · *Factory default

Page 104 of the Lexmark M412 user manual — 92 Chapter 3: Using the Operator Panel and Menus
Page 104 · click to enlarge
Page 104

Network Menu (continued)

Network Buffer Auto* 3K to maximum size allowed

You can configure the size of the network input buffer to meet the requirements of your system. If the limited size of the network buffer is preventing you from continuing work in your software application each time you send a job to the printer, you may want to increase the buffer size.

The maximum size available for modification depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the network buffer size, you can disable or reduce the size of the parallel and USB buffers.

Choose Auto to let the printer calculate the buffer size proportional to the total amount of available printer memory. In most cases, Auto is the recommended setting.

Network 1 Setup Values for this menu item are supplied by the specific network card. Open the menu to see the available values.

For more information, refer to the documentation that comes with your network option.

92 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 105 of the Lexmark M412 user manual — 93 Operator Panel Menus
Page 105 · click to enlarge
Page 105

Infrared Menu Use the INFRARED MENU to change settings affecting jobs sent to the printer through the infrared interface port.

If Infrared Port is set to Disabled, all other menu items in the INFRARED MENU are not available.

This menu is only available if the Tri-Port interface option card is installed in your printer.

Infrared Menu

Infrared Port Disabled* IR Option 1

Select IR Option 1 to activate the infrared port on the Tri-Port interface option card. If you select Disabled, all of the other menu items in the INFRARED MENU are not available.

PCL SmartSwitch Off On*

If PCL SmartSwitch is set to On, the printer examines the data on the infrared interface connection and selects PCL emulation if the data indicates that is the printer language.

If both PCL SmartSwitch and PS SmartSwitch are set to Off, the printer uses the language specified in the Printer Language menu as the default. If only one SmartSwitch setting is set to Off, the printer uses the language that has its SmartSwitch setting set to On as the default.

PS SmartSwitch Off On*

If PS SmartSwitch is set to On the printer examines the data on the network infrared connection and selects PostScript 3 emulation if the data indicates that is the printer language.

If both PCL SmartSwitch and PS SmartSwitch are set to Off, the printer uses the language specified in the Printer Language menu as the default. If only one SmartSwitch setting is set to Off, the printer uses the language that has its SmartSwitch setting set to On as the default.

93 Operator Panel Menus

Menu Item Values · *Factory default

Page 106 of the Lexmark M412 user manual — 94 Chapter 3: Using the Operator Panel and Menus
Page 106 · click to enlarge
Page 106

Infrared Menu (continued)

NPA Mode Off Auto*

NPA is a mode of bidirectional communication that follows the conventions defined in Network Printing Alliance Protocol, A Printer/Host Control Specification Developed by the NPA. NPA mode requires special processing of the print data.

If NPA Mode is set to On, the data received must be in NPA format. If not, it is rejected as bad data. If NPA Mode is set to Off, the printer does not perform any NPA processing. If NPA Mode is set to Auto, the printer examines the data to determine the format and then processes it in either format.

The NPA Mode setting in the INFRARED MENU applies only to the infrared interface connection.

Infrared Buffer Disabled Auto* 5K to maximum size allowed

You can configure the size of the infrared input buffer to meet the requirements of your system. If the limited size of the input buffer is preventing you from continuing work in your software application each time you send a job to the printer, you may want to increase the buffer size.

The maximum size available for modification depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the infrared buffer size, you can disable or reduce the size of the parallel, serial, LocalTalk, and USB buffers.

Choose Auto to let the printer calculate a buffer size proportional to the total amount of available printer memory. In most cases, Auto is the recommended setting.

Window Size Auto* 1

The Window Size setting specifies the maximum number of infrared frames the printer can receive before it must send an acknowledgment to the host computer.

Select Auto to let the printer automatically set the window size during a power on reset to maximize link performance.

In most cases, Auto is the recommended setting. If you have trouble printing using the infrared port, changing the Window Size setting to 1 may resolve the problem.

94 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 107 of the Lexmark M412 user manual — 95 Operator Panel Menus
Page 107 · click to enlarge
Page 107

Infrared Menu (continued)

Transmit Delay Auto* None 1…15

The Transmit Delay setting defines the amount of time the printer must wait before trans- mitting meaningful infrared data to the host computer, as well as the amount of time the printer requests the host computer to wait before it transmits infrared data.

Select Auto to let the printer automatically set the Transmit Delay value during a power on reset to maximize link performance.

In most cases, Auto is the recommended setting. If you have trouble printing using the infrared port, selecting a high Transmit Delay setting, such as 15, may resolve the problem.

Max Baud Rate 2400 9600 19200 38400 57600 115200 576000 1152000* 4000000

The maximum baud rate possible for both the printer and the infrared adapter is automatically set during a power on reset. However, if your printer is situated in a bright or highly reflective environment, you may experience intermittent communication problems. If you do, select a lower baud rate for the infrared connection.

95 Operator Panel Menus

Menu Item Values · *Factory default

Page 108 of the Lexmark M412 user manual — 96 Chapter 3: Using the Operator Panel and Menus
Page 108 · click to enlarge
Page 108

LocalTalk Menu Use the LOCALTALK MENU to change settings affecting jobs sent to the printer through the LocalTalk port.

If LocalTalk Port is set to Disabled, all other menu items in the LOCALTALK MENU are not available.

This menu is only available if the Tri-Port interface option card is installed in your printer.

LocalTalk Menu

LocalTalk Port Disabled* LTalk Option 1

Select LTalk Option 1 to activate the LocalTalk port on the Tri-Port interface option card.

If you select Disabled, all of the other menu items in the LOCALTALK MENU are not available.

PCL SmartSwitch Off On*

If PCL SmartSwitch is set to On, the printer examines the data on the LocalTalk interface connection and selects PCL emulation if the data indicates that is the printer language.

If both PCL SmartSwitch and PS SmartSwitch are set to Off, the printer uses the language specified in the Printer Language menu as the default. If only one SmartSwitch setting is set to Off, the printer uses the language that has its SmartSwitch setting set to On as the default.

PS SmartSwitch Off On*

If PS SmartSwitch is set to On, the printer examines the data on the specified LocalTalk interface connection and selects PostScript 3 emulation if the data indicates that is the printer language.

If both PCL SmartSwitch and PS SmartSwitch are set to Off, the printer uses the language specified in the Printer Language menu as the default. If only one SmartSwitch setting is set to Off, the printer uses the language that has its SmartSwitch setting set to On as the default.

96 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 109 of the Lexmark M412 user manual — 97 Operator Panel Menus
Page 109 · click to enlarge
Page 109

LocalTalk Menu (continued)

NPA Mode Off Auto*

NPA is a mode of bidirectional communication that follows the conventions defined in Network Printing Alliance Protocol, A Printer/Host Control Specification Developed by the NPA. NPA mode requires special processing of the print data.

If NPA Mode is set to On, the data received must be in NPA format. If not, it is rejected as bad data. If NPA Mode is set to Off, the printer does not perform any NPA processing. If NPA Mode is set to Auto, the printer examines the data to determine the format and then processes it in either format.

The NPA Mode setting in the LOCALTALK MENU applies only to the LocalTalk interface connection.

LocalTalk Buffer Disabled Auto* 6K to maximum size allowed

You can configure the size of the LocalTalk input buffer to meet the requirements of your system. If the limited size of the input buffer is preventing you from continuing work in your software application each time you send a job to the printer, you may want to increase the buffer size.

The maximum size available for modification depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the LocalTalk buffer size, you can disable or reduce the size of the parallel, serial, infrared, and USB buffers.

Choose Auto to let the printer calculate a buffer size proportional to the total amount of available printer memory. In most cases, Auto is the recommended setting.

NPA Hosts 1…10 (2*)

Use this setting to specify the maximum number of NPA hosts that can register for NPA printer alerts. When the number of hosts registered for NPA alerts exceeds the quantity specified by NPA Hosts, any additional hosts attempting to register for alerts are ignored.

LocalTalk Name Lexmark Optra M410 or Lexmark Optra M412

This setting identifies the printer model name stored in printer memory. It cannot be modified through the operator panel.

97 Operator Panel Menus

Menu Item Values · *Factory default

Page 110 of the Lexmark M412 user manual — 98 Chapter 3: Using the Operator Panel and Menus
Page 110 · click to enlarge
Page 110

LocalTalk Menu (continued)

LocalTalk Addr (LocalTalk Node Number)

This setting identifies the LocalTalk Node number assigned to the printer. It cannot be modified through the operator panel.

LocalTalk Zone (Zone name provided by LocalTalk network)

This setting determines the LocalTalk Zone. It cannot be modified through the operator panel.

98 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 111 of the Lexmark M412 user manual — 99 Operator Panel Menus
Page 111 · click to enlarge
Page 111

USB Menu Use the USB MENU to change settings affecting the Uni- versal Serial Bus (USB) interface port. The USB MENU displays as a standard feature or as an option, and appears as one of the following:

  • STANDARD USB
  • USB OPTION 1

USB OPTION 1 is only available if a parallel/USB inter- face option card is installed on the printer system board. See “Using a USB Cable” on page 14 for information on how to attached a USB cable and “Parallel/USB Interface Option Card” on page 215 for installation information.

USB Menu

PCL SmartSwitch Off On*

If PCL SmartSwitch is set to On, the printer examines the data on the USB interface connection and selects PCL emulation if the data indicates that is the printer language.

If both PCL SmartSwitch and PS SmartSwitch are set to Off, the printer uses the language specified in the Printer Language menu as the default. If only one SmartSwitch setting is set to Off, the printer uses the language that has its SmartSwitch setting set to On as the default.

PS SmartSwitch Off On*

If PS SmartSwitch is set to On, the printer examines the data on the specified USB interface connection and selects PostScript 3 emulation if the data indicates that is the printer language.

If both PCL SmartSwitch and PS SmartSwitch are set to Off, the printer uses the language specified in the Printer Language menu as the default. If only one SmartSwitch setting is set to Off, the printer uses the language that has its SmartSwitch setting set to On as the default.

99 Operator Panel Menus

Menu Item Values · *Factory default

Page 112 of the Lexmark M412 user manual — 100 Chapter 3: Using the Operator Panel and Menus
Page 112 · click to enlarge
Page 112

USB Menu (continued)

NPA Mode On Off Auto*

NPA is a mode of bidirectional communication that follows the conventions defined in Network Printing Alliance Protocol, A Printer/Host Control Specification Developed by the NPA. NPA mode requires special processing of the print data.

If NPA Mode is set to On, the data received must be in NPA format. If not, it is rejected as bad data. If NPA Mode is set to Off, the printer does not perform any NPA processing. If NPA Mode is set to Auto, the printer examines the data to determine the format and then processes it in either format.

The NPA Mode setting in the USB MENU applies only to the USB interface connection.

USB Buffer Disabled Auto* 3K to maximum size allowed

You can configure the size of the USB input buffer to meet the requirements of your system. If the limited size of the input buffer is preventing you from continuing work in your software application each time you send a job to the printer, you may want to increase the buffer size.

The maximum size available for modification depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the USB buffer size, you can disable or reduce the size of the parallel, serial, network, infrared, and LocalTalk buffers.

Choose Auto to let the printer calculate a buffer size proportional to the total amount of available printer memory. In most cases, Auto is the recommended setting.

100 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 113 of the Lexmark M412 user manual — 101 Operator Panel Menus
Page 113 · click to enlarge
Page 113

USB Menu (continued)

Job Buffering Off* On

This menu item only displays if you are using standard USB and have a hard disk option card installed.

Job buffering lets you delay processing of a print job. The job is temporarily stored on a hard disk option before being printed, usually freeing the host computer while the job prints.

The Job Buffering menu item only displays if the installed hard disk option is formatted and is not defective, Read/Write or Write protected, and if Job Buffer Size is not set to Disabled. See Job Buffer Size on page 77 for more information. 61 Defective Disk may display when the printer is turned on, or during disk format and write operations. See 61 Defective Disk on page 165 for more information.

If Job Buffering is set to On, print jobs are buffered to the hard disk option. If Job Buffering is set to Off, print jobs are not buffered.

101 Operator Panel Menus

Menu Item Values · *Factory default

Page 114 of the Lexmark M412 user manual — 102 Chapter 3: Using the Operator Panel and Menus
Page 114 · click to enlarge
Page 114

Fax Menu Use the FAX MENU to change settings affecting fax data received by the printer through the serial interface port on the Tri-Port interface option card.

With the Tri-Port interface option card installed, the printer can receive and print fax data.

If Fax Port is set to Disabled, all other menu items in the FAX MENU are not available.

Ser Option 1 is only available if a Tri-Port interface option card is installed in your printer. See “Tri-Port Interface Option Card” on page 212 or “Fax” on page 197 for more information.

Fax Menu

Fax Port Disabled* Ser Option 1

Select Ser Option 1 to activate the serial port on the Tri-Port interface option card and configure it to receive fax data.

If you select Disabled, all of the other menu items in the FAX MENU are not available.

Fax Baud 1200 2400 4800 9600 19200* 38400 57600 115200

This setting lets you select the rate at which fax data is being sent to or from your computer. Refer to the Technical Reference for information about the range of baud values.

Fax Data Bits 7 8*

This setting lets you select the number of fax data bits that are sent in each transmission frame. Refer to the Technical Reference for more information about data bits.

102 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 115 of the Lexmark M412 user manual — 103 Operator Panel Menus
Page 115 · click to enlarge
Page 115

Fax Menu (continued)

Fax Parity Even Odd None* Ignore

The Fax Parity setting lets you select the parity for fax data frames.

Even The port expects to receive data frames with an even number of logical 1’s per byte. The port transmits XOFF and XON with even parity. If the port detects a parity error, it sends an inverted question mark to the printer instead of the character sent by the host system. Odd The port expects to receive data frames with an odd number of logical 1’s per byte. The printer transmits XOFF and XON with odd parity. If the printer detects a parity error, it sends X'5F' to the printer instead of the character sent by the host system. None The port expects no parity bit when it receives data. The port transmits XON and XOFF without parity bits. Ignore The port expects a parity bit when it receives a data frame. The port ignores the

parity bit and uses even parity when it transmits XON and XOFF.

Refer to the Technical Reference for more information about parity.

Fax Buffer Disabled Auto* 105K to max size allowed

You can configure the size of the fax input buffer to meet the requirements of your system. If the limited size of the input buffer is preventing you from receiving fax data, you may want to increase the fax buffer size.

The maximum size depends on the amount of memory in your printer, the size of the other link buffers and whether the Resource Save setting is set to On or Off. To maximize the range for the fax buffer size, you can disable or reduce the size of the parallel, infrared, LocalTalk, and USB buffers.

Choose Auto to let the printer calculate a buffer size proportional to the total amount of available printer memory. In most cases, Auto is the recommended setting.

103 Operator Panel Menus

Menu Item Values · *Factory default

Page 116 of the Lexmark M412 user manual — 104 Chapter 3: Using the Operator Panel and Menus
Page 116 · click to enlarge
Page 116

Fax Menu (continued)

Fax Paper Size A4* (Country specific) A5 JIS B5 Letter* (Country specific) Legal Executive Universal

The Fax Paper Size setting lets you specify the size of print material used for printing fax data. Incoming faxes are automatically formatted to print on the paper size set in the Fax Paper Size menu item.

The printer automatically prints from the paper source containing the correct paper size and paper type as specified in the Fax Paper Size and Fax Paper Type settings. If no paper source contains the correct paper size and paper type, you are prompted to change the print material in a selected source to match the Fax Paper Size and Fax Paper Type settings. See Fax Paper Type on page 105 for more information.

104 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · *Factory default

Page 117 of the Lexmark M412 user manual — 105 Operator Panel Menus
Page 117 · click to enlarge
Page 117

Fax Menu (continued)

Fax Paper Type Plain Paper* Card Stock Transparency Labels Bond Letterhead Preprinted Colored Paper Custom Type 1 Custom Type 2 Custom Type 3 Custom Type 4 Custom Type 5 Custom Type 6

The Fax Paper Type setting lets you specify the type of print material used for printing fax data.

The printer automatically prints from the paper source containing the correct paper size and paper type as specified in the Fax Paper Size and Fax Paper Type settings. If no paper source contains the correct paper size and paper type, you are prompted to change the print material in a selected source to match the Fax Paper Size and Fax Paper Type settings. See Fax Paper Size on page 104 for more information.

Custom Type 1 through 6 refers to special types of print materials. You can change the names through a utility, such as MarkVision. The user-defined name is truncated to 14 characters. For more information on setting the Custom Type names, see CUSTOM TYPES on page 49.

105 Operator Panel Menus

Menu Item Values · *Factory default

Page 118 of the Lexmark M412 user manual — 106 Chapter 3: Using the Operator Panel and Menus
Page 118 · click to enlarge
Page 118

Config Menu You only have access to the CONFIG MENU if you follow these steps:

1 Turn the printer power Off (O).

2 Press and hold the Select and Return buttons and turn the printer power On (|).

3 Release the buttons when Performing Self Test appears on the operator panel display.

When the printer self test completes, the CONFIG MENU displays.

When you exit the CONFIG MENU, the printer restarts automatically and returns to the Ready state. See Exit Config Menu on page 107 for more information.

Config Menu

Prt Quality Pgs Press Select to print the quality test pages. The first page contains a combination of graphics and text which always prints in English. The second and third pages contain graphics only.

Panel Menus Disable Enable*

For more information, see “Disabling the Operator Panel Menus” on page 41.

Select Discard to delete all print jobs stored in the print buffer.

The message Formatting Disk briefly appears while the buffered jobs are being discarded. See Formatting Disk on page 153 for more information.

106 Chapter 3: Using the Operator Panel and Menus

Menu Item Values · Buffered Jobs Discard · *Factory default

Page 119 of the Lexmark M412 user manual — 107 Operator Panel Menus
Page 119 · click to enlarge
Page 119

Config Menu (continued)

Factory Defaults Restore All

If you select Restore All:

  • All downloaded resources (fonts, macros, symbol sets) in printer memory (RAM) are deleted. (Resources residing in flash memory or on the hard disk option are unaffected.)
  • All menu settings are returned to the factory default values except: – Display Language (SETUP MENU) which is the operator panel display language. – All settings in the PARALLEL MENU, SERIAL MENU, NETWORK MENU, INFRARED

MENU, LOCALTALK MENU, USB MENU, and FAX MENU.

The message Restoring Factory Defaults briefly appears while the printer restores the factory default settings. See Restoring Factory Defaults on page 157 for more information.

NARROW MEDIA Plain Width Card Stock Width Trnsprncy Width Labels Width Bond Width Letterhead Width Preprinted Width Colored Width Envelope Width Custom 1 Width Custom 2 Width Custom 3 Width Custom 4 Width Custom 5 Width Custom 6 Width

Each of the above menu items support the following values as a second menu:

Set NARROW MEDIA to Narrow when using print material less than 172 mm (6.77 in.) in width, so the printer can adjust its speed, thus prolonging the life of the fuser.

Custom x Width refers to special types of print materials. You can change the names through a utility, such as MarkVision. If a user-defined name is available, the name displays instead of Custom x Width, where x represents a number 1 through 6. The user-defined name is truncated to 16 characters.

Exit Config Menu Press Select to exit the CONFIG MENU. The printer automatically restarts and returns to the Ready state.

107 Operator Panel Menus

Menu Item Values · Normal* Narrow · *Factory default

Page 120 of the Lexmark M412 user manual — 108 Chapter 3: Using the Operator Panel and Menus
Page 120 · click to enlarge
Page 120

Understanding

The Print and Hold function lets you delay the printing of a job, print it later, and ask for additional copies.

Print and Hold Jobs

The types of Print and Hold jobs are:

  • Confidential Job
  • Repeat Print Job
  • Reserve Print Job
  • Verify Print Job

In the JOB MENU, there are two categories or menu items of Print and Hold jobs:

  • CONFIDENTIAL JOB
  • HELD JOBS

Repeat Print job, Reserve Print job, and Verify Print job are grouped into the category called Held Jobs.

You select the type of job you want from your software application or printer driver. To access your jobs once they are sent to print, you must use the operator panel or the remote operator panel in MarkVision to enter the JOB MENU.

Confidential Jobs When you send a Confidential Job, the printer formats your job and holds the job in memory. The printer delays the printing of your job until you enter a PIN assigned to the job. You enter the number through the operator panel. See “Entering a Personal Identification Number (PIN)” on page 111 for more information.

For more information about Confidential Jobs, see CONFIDENTIAL JOB on page 60.

  • To print all Confidential Jobs, see Print All Jobs on page 62.
  • To print a specific Confidential Job, see PRINT A JOB on page 62.
  • To print additional copies of a Confidential Job, see PRINT COPIES on page 64.

108 Chapter 3: Using the Operator Panel and Menus

Page 121 of the Lexmark M412 user manual — 109 Understanding Print and Hold Jobs
Page 121 · click to enlarge
Page 121
  • To delete all Confidential Jobs, see Delete All Jobs on page 63.
  • To delete a specific Confidential Job, see DELETE A JOB on page 63.

Held Jobs Held Jobs refers any of the following types of jobs: Repeat Print job, Reserve Print job, and Verify Print job.

Repeat Print Job

When you create a Repeat Print job, the job formats and prints, but the printer stores the job in memory so you can print additional copies of the job at a later time. As long as the job remains stored in memory, you may print addi- tional copies. Repeat Jobs are automatically deleted when the printer requires extra memory to process additional jobs or when the number of Repeat Jobs stored exceeds the value of the setting for Print and Hold Repeat Job Limit. For more information about this setting, refer to the Technical Reference.

Reserve Print Job

When you create a Reserve Print job, the job formats, but does not print. The printer stores the job in memory so you can print the job at a later time. All pages in the job are held in memory until you activate printing by using the operator panel to select Print All Jobs or PRINT A JOB. Reserve Print jobs are not deleted from memory when the job prints. To delete a Reserve Print job, you must request DELETE A JOB using the operator panel.

109 Understanding Print and Hold Jobs

Page 122 of the Lexmark M412 user manual — 110 Chapter 3: Using the Operator Panel and Menus
Page 122 · click to enlarge
Page 122

Verify Print Job

When you create a Verify Print job, the job formats, and one copy of the job prints. Additional requested copies are held in printer memory. You specify the number of copies you want when you send the job from the printer driver. This allows you to examine the first copy to see if it is sat- isfactory before you print the other copies.

If the job is unsatisfactory, you would not want the other copies to print. To delete the job, you must select the DELETE A JOB value, and select this job to delete it. See DELETE A JOB on page 68 for more information.

If the job is satisfactory, you can change the number of copies to print or print the number of copies already set in the printer driver.

To change the number of remaining copies to print:

1 Select PRINT COPIES.

2 Select the specific job.

3 At the Copies prompt, change the number of copies to print from the number set in the printer driver and press Select.

4 Press Return until you exit the menus or press Go to exit the menus. Once the printer exits the menus and returns to an online state, the remaining copies print.

Once all copies are printed, the job is deleted from printer memory. For more information, see PRINT COPIES on page 69.

To print the number of copies set in the printer driver:

1 Select PRINT A JOB.

2 Select the specific job. The remaining copies print.

Once all copies are printed, the job is deleted from printer memory. For more information, see PRINT A JOB on page 67.

110 Chapter 3: Using the Operator Panel and Menus

Page 123 of the Lexmark M412 user manual — 111 Entering a Personal Identification Number (PIN)
Page 123 · click to enlarge
Page 123

Printing and Deleting

Once you have sent a Repeat Print job, a Reserve Print job, or a Verify Print job from the software application or the printer driver and have selected a value in the HELD JOBS menu item, the jobs are displayed on the operator panel in lists. You may choose to delete all, delete one or more indi- vidually, print all, print one or more individually, or print multiple copies of a job.

Held Jobs

  • To print all Held Jobs, see Print All Jobs on page 67.
  • To print one or more Held Jobs by selecting them individually, see PRINT A JOB on page 67.
  • To print additional copies of a Held Job, see PRINT COPIES on page 69.
  • To delete all Held Jobs, see Delete All Jobs on page 68.
  • To delete one or more Held Jobs by selecting them individually, see DELETE A JOB on page 68.

Entering a

Once you send a Confidential Job from your software application or printer driver, it is processed and held in printer memory. A Personal Identification Number (PIN) is paired with the print job in printer memory.

Personal Identification Number (PIN)

Entry of the PIN using the operator panel is required to delete or print a Confidential Job.

When you want to access your Confidential Job held in printer memory, you:

1 Press Menu> to enter the menus and go to the JOB

MENU.

If JOB MENU is on the first line of the display, con- tinue with step 2. If JOB MENU is on the second line, press Select.

2 Continue to press and release Menu> until you see

CONFIDENTIAL JOB on the second line of the dis- play.

111 Entering a Personal Identification Number (PIN)

Page 124 of the Lexmark M412 user manual — 112 Chapter 3: Using the Operator Panel and Menus
Page 124 · click to enlarge
Page 124

3 Press Select.

The following prompt appears on the display:

Enter PIN=____

You are required to enter the four-digit PIN associ- ated with your Confidential Job next to the equal sign (=). Each digit must be a number from 1 to 6.

At this point, the buttons on the operator panel cease to function as before, such as scrolling through the menus. You press the numbers on the operator panel like pressing numbers on a calcula- tor. To simplify the operator panel, the illustration shows just the numbers and not the names of the operator panel buttons.

As you press each button to enter each digit of your PIN, an asterisk (*) appears on the display.

If you make a mistake entering your PIN, for instance, if you enter a number incorrectly, con- tinue to press any of the buttons until the mes- sage No Jobs Found. Retry? displays. Press Go to refresh the operator panel and the Enter PIN: prompt displays again.

If you enter a PIN that does not match any Confi- dential Job in printer memory, the message No Jobs Found. Retry? displays. Press Go to refresh the operator panel and display the Enter PIN: prompt again or press Stop to cancel the entry of a PIN.

Once you successfully enter the PIN, the printer checks the PIN with each stored PIN associated with each Confidential Job in printer memory. If the number matches, you are given access to the next level of the CONFIDENTIAL JOB menu item where you can select to print or delete jobs matching the PIN.

112 Chapter 3: Using the Operator Panel and Menus

Page 125 of the Lexmark M412 user manual — HELD JOBS
Page 125 · click to enlarge
Page 125

Print and Hold Formatting Errors

A lightning bolt symbol displays on the operator panel to indicate a formatting error occurred on at least one type of Print and Hold job. It looks like this:

When this type of error occurs, a portion of the processed job may still print, so the printer does not discard the entire job. Instead the lightning bolt displays to tell you that there is a formatting error on the particular job.

When any values are selected from either the CONFIDEN- TIAL JOB menu item or the HELD JOBS menu item, the symbol displays next to the value if at least one job experi- ences a formatting error as shown:

HELD JOBS

CONFIDENTIAL JOB

CONFIDENTIAL JOB

HELD JOBS

PRINT A JOB

PRINT A JOB

CONFIDENTIAL JOB

HELD JOBS

CONFIDENTIAL JOB

HELD JOBS

DELETE A JOB

DELETE A JOB

CONFIDENTIAL JOB

HELD JOBS

PRINT COPIES

PRINT COPIES

113 Print and Hold Formatting Errors

Show 4 more labels / short text on this page
Print All Jobs · Print All Jobs · Delete All Jobs · Delete All Jobs
Page 126 of the Lexmark M412 user manual — 114 Chapter 3: Using the Operator Panel and Menus
Page 126 · click to enlarge
Page 126

Once you select PRINT A JOB, DELETE A JOB, or PRINT COPIES values in the CONFIDENTIAL JOB menu item or the HELD JOBS menu item, the lightning bolt displays by the value if the currently displayed job experiences a formatting error. For example, if three jobs are sent to print and the second job experiences a formatting error, when you select PRINT COPIES, the operator panel displays as follows as you use the Menu> button to scroll to each job:

PRINT COPIES Job #1

PRINT COPIES Job #2

PRINT COPIES Job #3

The lightning bolt only displays for the second job since it is the only job that encountered a formatting error.

114 Chapter 3: Using the Operator Panel and Menus

Page 127 of the Lexmark M412 user manual — 115 Using Print Materials
Page 127 · click to enlarge
Page 127
Lexmark M412 — Using Print Materials diagram (page 127)
Fig. 29 · Using Print Materials

This chapter provides specifications and guidelines for each type of print material that can be used with your printer, as well as important information about the paper sources and the output bins.

Lexmark M412 — Using Print Materials diagram (page 127)
Fig. 30 · Using Print Materials

Your printer has two standard paper sources, the 250-sheet input tray and the multipurpose feeder, and two output bins, providing high quality printing on a variety of print materials from different paper sources.

Load the print material you use for the majority of your print jobs in the 250-sheet input tray.

Reserve the multipurpose feeder for when you print on different sizes and types of print material, such as card stock, transparencies, postcards, note cards, and enve- lopes. You may also want to use the multipurpose feeder for single page print jobs on letterhead, or other special print material you do not keep in an input tray.

115 Using Print Materials

Optional 500-Sheet Drawer

Page 128 of the Lexmark M412 user manual — 116 Chapter 4: Using Print Materials
Page 128 · click to enlarge
Page 128

Paper Sources

The following table details the types and quantities of media you can load in each of the paper sources. For more information about selecting specific print material for use with your printer, see “Print Material Guidelines” on page 118.

and Sizes

See “Paper and Envelope Dimensions” on page 117 for a list of the print material and envelope sizes your printer supports.

Paper Source Specifications

Paper Weight 1 Capacity 2

Tray 1 (250-sheet input tray)

A4, JIS B5, letter, legal, executive

60 to 90 g/m2

(16 to 24 lb)

up to 100 labels 3

Tray 2 (optional 500-sheet drawer)

Paper only A4, JIS B5, letter, legal, executive

60 to 90 g/m2

(16 to 24 lb)

Multipurpose feeder Paper, envelopes, labels, transparencies, card stock 4

Minimum69.85 x 127 mm (2.75 x 5.0 in.) 5

60 to 163 g/m2

(16 to 43 lb)

Maximum215.9 x 356 mm (8.5 x 14 in.)

Supports all sizes listed in the “Paper and Envelope Dimensions” table on page 117.

10 sheets card stock

1 This refers to paper only. For weights of other print materials, refer to the Card Stock & Label Guide for more infor- mation. 2 For 20 lb print material, unless otherwise noted. 3 Refer to the Card Stock & Label Guide for more information. 4 3 x 5 in. and 4 x 6 in. index cards must exit to the rear output bin. 5 Print material 152.4 mm (6 in.) or less in length must exit to the rear output bin.

116 Chapter 4: Using Print Materials

Show 9 more labels / short text on this page
Source Media Sizes · Paper, labels, transparencies · 250 sheets paper · 50 transparencies · 500 sheets paper · 100 sheets paper · 10 envelopes · 30 labels · 20 transparencies
Page 129 of the Lexmark M412 user manual — 117 Paper Sources and Sizes
Page 129 · click to enlarge
Page 129

The following table lists the paper and envelope sizes you can use with your printer.

Paper and Envelope Dimensions

Paper Dimensions Envelope Dimensions

A4 210 x 297 mm (8.27 x 11.7 in.)

7 3/4 Envelope (Monarch)

98.4 x 190.5 mm (3.875 x 7.5 in.)

A5 (Multipurpose feeder only)

148 x 210 mm (5.83 x 8.27 in.)

9 Envelope 98.4 x 225.4 mm (3.875 x 8.875 in.)

JIS B5 182 x 257 mm (7.17 x 10.12 in.)

104.8 x 241.3 mm (4.125 x 9.5 in.)

Letter 215.9 x 279.4 mm (8.5 x 11 in.)

DL Envelope 110 x 220 mm (4.33 x 8.66 in.)

Legal 215.9 x 356 mm (8.5 x 14 in.)

C5 Envelope 162 x 229 mm (6.38 x 9.01 in.)

Executive 184.2 x 266.7 mm (7.25 x 10.5 in.)

B5 Envelope 176 x 250 mm (6.93 x 9.84 in.)

215.9 x 356 mm (8.5 x 14 in.)

Other Envelope 2 229.11 x 356 mm (9.02 x 14 in.)

1 Select this value when using a non-standard size sheet of print material. The printer formats the page for the maximum size (8.5 x 14 in.). Set the actual size from your software application. 2 Select this value when using a non-standard size of envelope. The printer formats the envelope for the maximum size (9.02 x 14 in.). Set the actual size from your software application.

117 Paper Sources and Sizes

10 Envelope (Com-10) · Universal 1 · (Multipurpose feeder only)

Page 130 of the Lexmark M412 user manual — 118 Chapter 4: Using Print Materials
Page 130 · click to enlarge
Page 130

Print Material

Selecting the appropriate print material (paper, transpar- encies, envelopes, labels, and card stock) for your printer helps you avoid printing problems.

Guidelines

The following sections contain guidelines for choosing the correct print material for your printer.

Paper For the best print quality, use 75 g/m2 (20 lb) xerographic, grain long paper. Try a sample of any paper you are con- sidering using with the printer before buying large quanti- ties.

When loading paper, note the recommended print side on the paper package, and load paper accordingly. See “Loading Print Material” on page 124 for detailed loading instructions.

The following papers are not recommended for use with your printer:

  • Paper with a rough or heavily textured surface
  • Coated papers, such as erasable bond
  • Preprinted papers manufactured with chemicals that may contaminate the printer
  • Multiple-part forms
  • Synthetic papers
  • Thermal papers
  • Recycled paper having a weight less than 75 g/m 2 (20 lb)

Letterhead Preprinted papers such as letterhead must be able to with- stand temperatures up to 200°C (392°F) without melting or releasing hazardous emissions. Use inks that are not affected by the resin in toner or the silicone in the fuser. Inks that are oxidation-set or oil-based should meet these requirements; latex inks might not.

118 Chapter 4: Using Print Materials

Page 131 of the Lexmark M412 user manual — 119 Print Material Guidelines
Page 131 · click to enlarge
Page 131

Transparencies You can feed transparencies from the 250-sheet input tray or the multipurpose feeder. Try a sample of any transpar- encies you are considering using with the printer before buying large quantities.

Do not load transparencies in the optional 500-sheet drawer. To load transparencies in the 250-sheet input tray, see page 124. To load transparencies in the multipurpose feeder, see page 141.

When printing on transparencies:

  • Use transparencies designed specifically for laser printers. Transparencies must be able to withstand temperatures of 175°C (347°F) without melting, discoloring or releasing hazardous emissions.
  • To prevent print quality problems, avoid getting fingerprints on the transparencies.
  • Before loading transparencies, fan the stack to prevent sheets from sticking together.

Envelopes You can load up to 10 envelopes in the multipurpose feeder. Try a sample of any envelopes you are considering using with the printer before buying large quantities. See page 141 for loading instructions.

When printing on envelopes:

  • Use envelopes made from 75 to 105 g/m 2 (20 to 28 lb) bond paper. For best performance and fewer paper jams, do not use envelopes that:

– Have excessive curl. – Are stuck together. – Are damaged in any way. – Contain windows, holes, perforations, cutouts or embossing. – Use metal clasps, string ties, or metal folding bars. – Have postage stamps attached. – Have any exposed adhesive when the flap is in the sealed or closed position.

119 Print Material Guidelines

Page 132 of the Lexmark M412 user manual — 120 Chapter 4: Using Print Materials
Page 132 · click to enlarge
Page 132
  • Use envelopes that can withstand temperatures of 205°C (401°F) without sealing, excessive curling, wrinkling, or releasing hazardous emissions.
  • Adjust the right paper guide to fit the width of the envelopes.
  • Load envelopes with the flap side down and the short edge nearest the return address positioned to enter the printer first. See page 147 for an illustration for loading envelopes.
  • If you are feeding self-sealing envelopes, open the rear output bin door so envelopes feed straight out the back of the printer. The rear output bin holds about 10 envelopes.

Labels Your printer can print on many labels designed for use with laser printers. These labels are supplied in letter-size and A4-size sheets. Label adhesives, face sheet (printable stock), and topcoats must be able to withstand tempera- tures of 205°C (401°F) and pressure of 25 pounds per square inch (psi).

Try a sample of any labels you are considering using with the printer before purchasing a large quantity.

For detailed information on label printing, characteristics and design, refer to the Card Stock & Label Guide on the CD that comes with your printer.

When printing on labels:

  • Do not load labels together with paper or transparencies in the same paper source.
  • Do not use label sheets with a slick backing material.
  • Do not print within 1 mm (0.040 in.) of the die cut.
  • Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial sheets will also contaminate your printer and your cartridge with adhesive, and could void your printer and cartridge warranties.

120 Chapter 4: Using Print Materials

Page 133 of the Lexmark M412 user manual — 121 Print Material Guidelines
Page 133 · click to enlarge
Page 133
  • Use labels that can withstand temperatures of 205°C (401°F) without sealing, excessive curling, wrinkling, or releasing hazardous emissions.
  • Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.
  • Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your warranty.
  • If zone coating of the adhesive is not possible, a 3 mm (0.125 in.) strip should be removed on the leading and driver edge, and a non-oozing adhesive should be used.
  • Remove a 3 mm (0.125 in.) strip from the leading edge to prevent labels from peeling inside the printer.
  • Portrait orientation is preferred, especially when printing bar codes.
  • Do not use labels that have exposed adhesive.
  • You may feed vinyl labels from the 250-sheet input tray and the multipurpose feeder.

After continuously printing approximately 10,000 pages of labels (or each time you replace the print cartridge), complete the following steps to maintain printer feeding reliability:

1 Print 5 sheets of paper.

2 Wait approximately 5 seconds.

3 Print 5 more sheets of paper.

121 Print Material Guidelines

Page 134 of the Lexmark M412 user manual — 122 Chapter 4: Using Print Materials
Page 134 · click to enlarge
Page 134

Card Stock

Card stock is single ply, and has a large array of proper- ties, such as the orientation of paper fibers and texture, that can significantly affect the print quality.

Guidelines

Try a sample of any card stock you are considering using with the printer before purchasing a large quantity.

See page 116 for information on the preferred weight of print materials.

When printing on card stock:

  • Use card stock that can withstand temperatures of 205°C (401°F) without sealing, excessive curling, wrinkling, or releasing hazardous emissions.
  • Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting introduces semi-liquid and volatile components in the printer.
  • Do not use card stock that is perforated or creased. It may cause paper jams.
  • We recommend the use of grain short card stock.

After printing approximately 10,000 pages of card stock (or each time you replace the print cartridge), complete the following steps to maintain printer feeding reliability:

1 Print 5 sheets of paper.

2 Wait approximately 5 seconds.

3 Print 5 more sheets of paper.

For detailed information on card stock printing, character- istics, and design, refer to the Card Stock & Label Guide on the CD.

122 Chapter 4: Using Print Materials

Page 135 of the Lexmark M412 user manual — 123 Storing Print Material
Page 135 · click to enlarge
Page 135

Storing Print

Use the following guidelines for proper print material storage:

Material

  • For best results, store print material in an environment where the temperature is approximately 21°C (70°F) and the relative humidity is 40%.
  • Store cartons of print material on a pallet or shelf, rather than directly on the floor.
  • If you store individual packages of print material, make sure they rest on a flat surface so the edges do not buckle or curl.
  • Do not place anything on top of the print material packages.

123 Storing Print Material

Page 136 of the Lexmark M412 user manual — 124 Chapter 4: Using Print Materials
Page 136 · click to enlarge
Page 136

Loading Print Material

Proper print material loading helps prevent paper jams and helps make your printing trouble-free.

Do not remove input trays while a job is printing or while Busy displays on the operator panel. Doing so may cause a paper jam.

Before loading print material, know the recommended print side of the print material you are using. This infor- mation is usually indicated on the print material package.

Loading an

Your printer has one standard 250-sheet input tray that holds five paper sizes: A4, B5, LTR (Letter), LGL (Legal), and EXE (Executive). The 250-sheet input tray also holds labels or transparencies.

Input Tray

You may purchase an optional 500-sheet drawer as a paper source. See “Optional 500-Sheet Drawer” on page 223 for installation information.

Lexmark M412 — Input Tray diagram (page 136)
Fig. 31 · Input Tray

To load print material in an input tray:

1 Pull the input tray straight out of the printer.

If you are loading the 250-sheet input tray, pull the input tray straight out and remove it completely from the printer.

If you are loading the input tray for the optional 500-sheet drawer, pull the input tray straight out and remove it completely from the support unit.

124 Chapter 4: Using Print Materials

Page 137 of the Lexmark M412 user manual — 125 Loading Print Material
Page 137 · click to enlarge
Page 137

2 Press down on the metal plate until it locks into place.

Lexmark M412 — Loading PrintMaterial diagram (page 137)
Fig. 32 · Loading PrintMaterial

The metal plate remains stationary on the inside bottom of the input tray.

3 Move the length guide to the correct position for the size print material you are loading.

Lexmark M412 — Loading PrintMaterial diagram (page 137)
Fig. 33 · Loading PrintMaterial

– For the 250-sheet input tray, press down on the length guide tab with one hand, and with the other hand slide the length guide to the correct position for the size print material you are load- ing.

125 Loading Print Material

Paper Size Indicators · Length Guide

Page 138 of the Lexmark M412 user manual — 126 Chapter 4: Using Print Materials
Page 138 · click to enlarge
Page 138

– For the 500-sheet input tray, lift the length guide straight up out of the input tray and replace it in the correct position.

Lexmark M412 — Loading PrintMaterial diagram (page 138)
Fig. 34 · Loading PrintMaterial

Insert the tabs located on each end of the length guide into the slots on the side of the input tray.

4 Press down on the width guide tab and slide the width guide to the far right side of the input tray as shown.

126 Chapter 4: Using Print Materials

Page 139 of the Lexmark M412 user manual — 127 Loading Print Material
Page 139 · click to enlarge
Page 139

5 Flex the sheets back and forth to loosen them, then fan them. Do not fold or crease the print material. Straighten the edges on a level surface.

Lexmark M412 — Loading PrintMaterial diagram (page 139)
Fig. 35 · Loading PrintMaterial

6 Place the print material against the left side of the input tray and insert it under the metal stop.

Lexmark M412 — Loading PrintMaterial diagram (page 139)
Fig. 36 · Loading PrintMaterial

Make sure the recommended print side is face down and the front edge is placed toward the front of the input tray.

For information on loading letterhead, see “Printing on Letterhead” on page 135.

127 Loading Print Material

Page 140 of the Lexmark M412 user manual — 128 Chapter 4: Using Print Materials
Page 140 · click to enlarge
Page 140
Lexmark M412 — Loading PrintMaterial diagram (page 140)
Fig. 37 · Loading PrintMaterial

7 Do not exceed the maximum stack height indi- cated by the line under the arrows.

8 Push on the right side of the width guide to move it to the left until it lightly touches the edge of the print material.

Lexmark M412 — Loading PrintMaterial diagram (page 140)
Fig. 38 · Loading PrintMaterial

128 Chapter 4: Using Print Materials

Page 141 of the Lexmark M412 user manual — 129 Loading Print Material
Page 141 · click to enlarge
Page 141
Lexmark M412 — Loading PrintMaterial diagram (page 141)
Fig. 39 · Loading PrintMaterial

9 Insert the input tray.

Slide the input tray all the way into the printer until it snaps into place.

Slide the 500-sheet input tray all the way into the support unit.

If an error message displays, see “Understanding Printer Messages” on page 151.

10 Send your job to print.

For information on duplexing, see “Manual Duplex Printing” on page 136.

129 Loading Print Material

Page 142 of the Lexmark M412 user manual — 130 Chapter 4: Using Print Materials
Page 142 · click to enlarge
Page 142

Loading the Multipurpose Feeder

Your printer has one standard multipurpose feeder that holds several sizes and types of print material, such as paper, card stock, transparencies, postcards, note cards, and envelopes. You can load approximately 100 sheets of 75 g/m2 (20 lb) paper at a time. You can also load approxi- mately 10 envelopes or 20 transparencies at a time.

You may also want to use the multipurpose feeder for sin- gle page print jobs on letterhead or other special print material you do not keep in an input tray.

For information on the types of print material that you can use with the multipurpose feeder, see “Paper Sources and Sizes” on page 116. For more information about using the multipurpose feeder, see “Multipurpose Feeder” on page 139.

Complete the following instructions to load print material in the multipurpose feeder:

1 Open the multipurpose feeder door. See “Opening the Multipurpose Feeder” on page 141 for more information.

2 Slide the paper width guide to the far right side of the multipurpose feeder. Paper Width Guide

Lexmark M412 — Loading the Multipurpose Feeder diagram (page 142)
Fig. 40 · Loading the Multipurpose Feeder

130 Chapter 4: Using Print Materials

Page 143 of the Lexmark M412 user manual — 131 Loading Print Material
Page 143 · click to enlarge
Page 143

3 Flex the sheets back and forth to loosen them, then fan them. Do not fold or crease the print material. Straighten the edges on a level surface.

Lexmark M412 — Loading the Multipurpose Feeder diagram (page 143)
Fig. 41 · Loading the Multipurpose Feeder

4 Locate the stack height limiter on the left side of the printer.

Lexmark M412 — Loading the Multipurpose Feeder diagram (page 143)
Fig. 42 · Loading the Multipurpose Feeder

5 Place the print material against the left side of the multipurpose feeder with the recommended print side face up and the top edge going in first toward the printer.

131 Loading Print Material

Stack Height Limiter

Page 144 of the Lexmark M412 user manual — 132 Chapter 4: Using Print Materials
Page 144 · click to enlarge
Page 144

6 Slide the print material into the multipurpose feeder as far as it will go. Do not force it. Forcing print material could cause a paper jam.

Lexmark M412 — Loading the Multipurpose Feeder diagram (page 144)
Fig. 43 · Loading the Multipurpose Feeder

7 Slide the paper width guide to the left until it lightly touches the edge of the print material.

Make sure the print material fits loosely in the mul- tipurpose feeder and is not bent or wrinkled. Do not overload the multipurpose feeder.

8 Send your job to print.

For information on duplexing, see “Manual Duplex Printing” on page 136.

132 Chapter 4: Using Print Materials

Page 145 of the Lexmark M412 user manual — 133 Using the Paper Exits (Output Bins)
Page 145 · click to enlarge
Page 145

Using the Paper Exits (Output Bins)

You printer has two standard paper exits. The following sections explain how to use the printer output bins.

Using the Standard Output Bin

The standard output bin holds 250 sheets of print material and is located on top of the printer. The printer automati- cally sends print jobs to the standard output bin.

The standard output bin collates print jobs face down.

133 Using the Paper Exits (Output Bins)

Standard Output Bin

Page 146 of the Lexmark M412 user manual — 134 Chapter 4: Using Print Materials
Page 146 · click to enlarge
Page 146

Using the Rear Output Bin

You may want to use the rear output bin when you print on different sizes and types of print material, such as paper, card stock, transparencies, postcards, note cards, and envelopes. The rear output bin holds 20 sheets of paper. For information on other types of print material, refer to the Card Stock & Label Guide.

The printer automatically sends print jobs to the rear out- put bin when you open it. The rear output bin reverse col- lates print jobs face up.

1 Locate the rear output bin door as shown.

Lexmark M412 — Using the Rear Output Bin diagram (page 146)
Fig. 44 · Using the Rear Output Bin

2 Pull the handhold to open the rear output bin.

3 Close the rear output bin door when you finish using it.

134 Chapter 4: Using Print Materials

Page 147 of the Lexmark M412 user manual — 135 Printing on Letterhead
Page 147 · click to enlarge
Page 147

Printing on

Check with the manufacturer or vendor to determine whether the preprinted letterhead you have chosen is acceptable for laser printers.

Letterhead

Page orientation is important when printing on letterhead. Use the following table for help when loading letterhead in the paper sources.

Orienting Letterhead

Tray 1 (250-sheet input tray)

Face down Front of tray (nearest tray handle)

Left side of tray

Tray 2 (optional 500-sheet drawer)

Multipurpose feeder (including feeding individual sheets)

Face up Rear of tray (enters the printer first)

Left side of tray

Tray Linking If you are using the same size and type of print material in all paper sources (input trays and the multipurpose feeder) and the PAPER MENU settings for the sources are the same, the automatic tray linking feature is enabled. For example, if you have the same size and type print material loaded in the standard 250-sheet tray and the optional 500-sheet drawer, the printer will select print material from one tray when the other becomes empty.

If you load the same size print material in each tray, make sure the print material is all the same type. If you use dif- ferent print material in the trays, each source with a differ- ent print material must have the PAPER TYPE set to a unique value to disable the automatic tray linking feature. See PAPER TYPE on page 47 for more information.

135 Printing on Letterhead

Top of page · Tray Print side · Portrait Landscape

Page 148 of the Lexmark M412 user manual — 136 Chapter 4: Using Print Materials
Page 148 · click to enlarge
Page 148

Manual Duplex

Manual duplex printing lets you print on both sides of paper and card stock.

Printing

Manual duplexing does not damage your printer, but print quality and feed reliability may vary when printing on the other side of the page.

To print on both sides of paper and card stock (called duplex printing or two-sided printing), print the first side of the print material like any other print job. When printing on the other side of the page, set PAPER WEIGHT to Heavy in the PAPER MENU to achieve the best results.

Make sure the placement or orientation of the print mate- rial is correct.

Duplex Printing from

When printing letterhead paper from the multipurpose feeder, load it with the design face up, so the top edge of the sheet with the logo enters the printer first.

the Multipurpose

Feeder

To print the second side of the sheet, load the printed side face down with the top edge of the sheet facing toward the printer.

Duplex Printing from

When printing letterhead paper from the trays, load it with the design face down with the top edge of the sheet facing toward the front of the printer.

the Trays

To print the second side of the sheet, load the printed side face up with the top edge of the sheet facing toward the front of the printer.

136 Chapter 4: Using Print Materials

Page 149 of the Lexmark M412 user manual — 137 Avoiding Paper Jams
Page 149 · click to enlarge
Page 149

Avoiding Paper Jams

If you follow the tips outlined in “Print Material Guide- lines” on page 118 and in “Loading Print Material” on page 124, you are well on your way to trouble-free print- ing. If jams do occur, however, follow the steps outlined in “Clearing Jams” on page 183. If jams occur frequently, make sure you are following these tips:

  • Use only recommended print materials. See “Print Material Guidelines” on page 118.
  • If you need to load print material in a tray while a job is printing, press the Stop button and wait for the printer motors to idle before you remove the tray from the printer. After you reinstall the loaded tray, press Go to continue printing.
  • Do not load wrinkled, creased, damp, or curled print material.
  • Flex, fan, and straighten the print material before you load it. If jams do occur, try manually feeding the print material one sheet at a time.
  • Do not overload the paper sources. Make sure the print material does not exceed the maximum height indicated on the stack height indicator.
  • Do not use print material that you have cut or trimmed yourself.
  • Do not mix print material sizes, weights, or types in the same paper source.
  • Do not use coated print materials.
  • Make sure the recommended print side is face down when loading all input trays and the recommended print side is face up when loading the multipurpose feeder.
  • Keep print materials stored in an acceptable environment. See “Storing Print Material” on page 123.
  • Do not remove input trays during a print job.

137 Avoiding Paper Jams

Page 150 of the Lexmark M412 user manual — 138 Chapter 4: Using Print Materials
Page 150 · click to enlarge
Page 150

138 Chapter 4: Using Print Materials

Page 151 of the Lexmark M412 user manual — 139 Multipurpose Feeder
Page 151 · click to enlarge
Page 151
Lexmark M412 — Multipurpose Feeder diagram (page 151)
Fig. 45 · Multipurpose Feeder

The multipurpose feeder is located on the front of your printer. It can be closed when you are not using it, making the printer more compact.

Lexmark M412 — Multipurpose Feeder diagram (page 151)
Fig. 46 · Multipurpose Feeder

You may want to use the multipurpose feeder when you print on different sizes and types of print material, such as paper, card stock, transparencies, postcards, note cards, and envelopes. You may also want to use the multipur- pose feeder for single-page print jobs on letterhead, or other special print material you do not keep in a paper tray.

You can load approximately 100 sheets of 75 g/m2 (20 lb) print material at a time. You can load approximately 10 envelopes or 20 transparencies at a time.

The maximum stack height for the loading of any print material is 10 mm (0.4 in.). Print material is loaded face up in the multipurpose feeder.

The multipurpose feeder accepts print material within the following dimensions:

Lexmark M412 — Multipurpose Feeder diagram (page 151)
Fig. 47 · Multipurpose Feeder

Width 69.85 mm (2.75 in.) 229.11 mm (9.02 in.)

Length 127 mm (5 in.) 355.6 mm (14 in.)

139 Multipurpose Feeder

Multipurpose Feeder

Page 152 of the Lexmark M412 user manual — 140 Chapter 5: Multipurpose Feeder
Page 152 · click to enlarge
Page 152

When printing from the multipurpose feeder, be sure to set the PAPER SIZE and PAPER TYPE for the MP Feeder menu item. Also, select the size and paper type from your software application for the print material you have loaded. See PAPER SIZE on page 45 and PAPER TYPE on page 47 for more information.

Multipurpose Feeder Guidelines

Follow these guidelines when using the multipurpose feeder:

  • Load only one size and type of print material or envelopes at a time in the multipurpose feeder.
  • To achieve the best possible print quality, use only high-quality print material that is designed for use in laser printers. See “Using Print Materials” on page 115 for guidelines on selecting types of print material.
  • To prevent paper jams, do not add print material to the multipurpose feeder until it is empty.
  • Do not close the multipurpose feeder while a job is printing or while Busy displays on the operator panel. Doing so may cause a paper jam.
  • Load print material with the top edge going into the multipurpose feeder first.
  • Do not place objects on the multipurpose feeder. Also, avoid pressing down or applying excessive force on it.

140 Chapter 5: Multipurpose Feeder

Page 153 of the Lexmark M412 user manual — 141 Opening the Multipurpose Feeder
Page 153 · click to enlarge
Page 153

Opening the Multipurpose

To open the multipurpose feeder door:

Lexmark M412 — Opening the Multipurpose diagram (page 153)
Fig. 48 · Opening the Multipurpose

1 Push the lower release latch on the front left side to release the multipurpose feeder door.

The multipurpose feeder door is the same as the lower front door.

The multipurpose feeder door opens and stops in place.

141 Opening the Multipurpose Feeder

Page 154 of the Lexmark M412 user manual — 142 Chapter 5: Multipurpose Feeder
Page 154 · click to enlarge
Page 154
Lexmark M412 — Opening the Multipurpose Feeder diagram (page 154)
Fig. 49 · Opening the Multipurpose Feeder

2 Locate the metal bar in the recessed area on the multipurpose feeder.

3 Pull the metal bar straight out to extend the multi- purpose feeder.

142 Chapter 5: Multipurpose Feeder

Page 155 of the Lexmark M412 user manual — 143 Loading the Multipurpose Feeder
Page 155 · click to enlarge
Page 155

Loading the Multipurpose

Proper loading prevents paper jams and ensures trouble-free printing. The following sections give detailed instructions for loading.

Feeder

Loading Print

Material

1 Locate the icons on the multipurpose feeder sur- face. These icons show the correct orientation for loading paper, as well as how to load letterhead and envelopes.

143 Loading the Multipurpose Feeder

Simplex Envelope

Page 156 of the Lexmark M412 user manual — 144 Chapter 5: Multipurpose Feeder
Page 156 · click to enlarge
Page 156

2 Slide the paper width guide to the far right side of the multipurpose feeder.

Lexmark M412 — Loading the Multipurpose Feeder diagram (page 156)
Fig. 50 · Loading the Multipurpose Feeder

3 Prepare specific print material for loading:

Lexmark M412 — 3 Prepare specific print material for loading: diagram (page 156)
Fig. 51 · 3 Prepare specific print material for loading:

– Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

– Hold transparencies by the edges and fan them to prevent feeding failures.

Lexmark M412 — 3 Prepare specific print material for loading: diagram (page 156)
Fig. 52 · 3 Prepare specific print material for loading:

144 Chapter 5: Multipurpose Feeder

Page 157 of the Lexmark M412 user manual — 145 Loading the Multipurpose Feeder
Page 157 · click to enlarge
Page 157

– Fan envelopes back and forth to loosen them. Do not fold or crease the envelopes. Straighten the edges on a level surface.

Lexmark M412 — Loading the Multipurpose Feeder diagram (page 157)
Fig. 53 · Loading the Multipurpose Feeder

4 Locate the stack height limiter on the left side of the multipurpose feeder.

5 Place the print material against the left side of the multipurpose feeder. Do not mix different sizes and types of print material.

145 Loading the Multipurpose Feeder

Stack Height Limiter

Page 158 of the Lexmark M412 user manual — 146 Chapter 5: Multipurpose Feeder
Page 158 · click to enlarge
Page 158

6 Load specific print material:

Lexmark M412 — 6 Load specific print material: diagram (page 158)
Fig. 54 · 6 Load specific print material:

– Load paper with the recommended print side face up and the top edge going in first as shown.

Lexmark M412 — 6 Load specific print material: diagram (page 158)
Fig. 55 · 6 Load specific print material:

– Load letterhead with the design face up and the top edge going in first as shown.

146 Chapter 5: Multipurpose Feeder

Page 159 of the Lexmark M412 user manual — 147 Loading the Multipurpose Feeder
Page 159 · click to enlarge
Page 159
Lexmark M412 — Loading the Multipurpose Feeder diagram (page 159)
Fig. 56 · Loading the Multipurpose Feeder

– Load transparencies with the recommended print side face up and the top edge going in first as shown.

– Load envelopes with the flap side down and the stamp area end going in last as shown.

Do not feed stamped envelopes into the multi- purpose feeder. The stamp is shown for place- ment only.

147 Loading the Multipurpose Feeder

Page 160 of the Lexmark M412 user manual — 148 Chapter 5: Multipurpose Feeder
Page 160 · click to enlarge
Page 160

7 Slide the print material into the multipurpose feeder as far as it will go. Do not force it. Forcing print material could cause a paper jam.

Lexmark M412 — Loading the Multipurpose Feeder diagram (page 160)
Fig. 57 · Loading the Multipurpose Feeder

8 Slide the paper width guide to the left until it lightly touches the edge of the print material.

Lexmark M412 — Loading the Multipurpose Feeder diagram (page 160)
Fig. 58 · Loading the Multipurpose Feeder

Make sure the print material fits loosely in the mul- tipurpose feeder and is not bent or wrinkled. Do not overload the multipurpose feeder.

148 Chapter 5: Multipurpose Feeder

Page 161 of the Lexmark M412 user manual — 149 Using the Multipurpose Feeder
Page 161 · click to enlarge
Page 161

Using the Multipurpose

After loading print material in the multipurpose feeder, select the paper source from your software application, and then select the paper size and type from both your software application and from the operator panel.

Feeder

To set the operator panel:

1 Make sure the PAPER SIZE for the multipurpose feeder (MP Feeder Size) is set to the correct size for the print material you are loading.

2 Make sure the PAPER TYPE for the multipurpose feeder (MP Feeder Type) is set to the correct value for the print material you are loading.

3 Make sure the PAPER LENGTH for the PAPER TYPE in the multipurpose feeder is set to the correct value for the print material you are loading.

Print material 152.4 mm (6 in.) or less in length must exit to the rear output bin. See “Using the Rear Output Bin” on page 134 for more information.

4 Press Go to return the printer to the Ready state.

149 Using the Multipurpose Feeder

Page 162 of the Lexmark M412 user manual — 150 Chapter 5: Multipurpose Feeder
Page 162 · click to enlarge
Page 162

Closing the Multipurpose

When you finish printing with the multipurpose feeder:

Feeder

1 Remove all print material.

Lexmark M412 — Feeder diagram (page 162)
Fig. 59 · Feeder

2 Push the metal bar straight back to collapse the multipurpose feeder to its short-length position.

Lexmark M412 — Feeder diagram (page 162)
Fig. 60 · Feeder

3 Close the multipurpose feeder door.

4 Close the rear output bin if you were printing on print material 152.4 mm (6 in.) or less in length. See page 134 for more information.

150 Chapter 5: Multipurpose Feeder

Page 163 of the Lexmark M412 user manual — 151 Status Messages
Page 163 · click to enlarge
Page 163

Understanding

Printer Messages 6

This chapter describes the various messages that may appear on your operator panel display. Status messages give information about the current state of the printer. Attendance messages indicate printer errors that you must resolve. Service messages indicate printer failures that may require servicing.

Status Messages The first line (line 1) on the display provides information on the current state or status of the printer, as shown in the tables beginning on page 152. However in some cases, a message is long enough that it requires both lines to dis- play the entire message.

Usually the second line (line 2) on the display provides additional information about printer status. See “Warning Messages” on page 158 for more information.

151 Status Messages

Page 164 of the Lexmark M412 user manual — 152 Chapter 6: Understanding Printer Messages
Page 164 · click to enlarge
Page 164

Line 1 Messages

Status Message Meaning and Actions Allowed While Message Displays

The printer is reset to activate a printer setting change.

No button actions are possible while this message displays.

The printer is busy receiving, processing, or printing data. The printer indicator light blinks while the printer is processing data.

The display shows one of the following items on line 1 while the printer processes data:

  • A PJL RDYMSG, if it is defined
  • A Network Printing Alliance (NPA) protocol job name, if one is defined
  • The printer language
  • Press Stop to take the printer out of the Busy state. The Not Ready message displays. No more data is processed, but all print material in the printer paper path prints. Press Go to return to Busy and continue receiving, processing, or printing data.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .
  • Print or delete Print and Hold jobs. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until CONFIDENTIAL JOB or HELD JOBS appears. Continue with the instructions for CONFIDENTIAL JOB on page 60 or HELD JOBS on page 65 to print all jobs, print a job, print copies, delete all jobs, or delete a job.

For more information, refer to the Technical Reference.

Cancelling Job The printer is processing a request to cancel the current print job.

Clearing Job Accounting Stat

The printer is deleting all job statistics stored on the hard disk option.

No button actions are possible while this message displays.

Defragmenting DO NOT POWER OFF

The printer is defragmenting the flash memory option to reclaim storage space occupied by deleted resources.

No button actions are possible while this message displays.

152 Chapter 6: Understanding Printer Messages

Activating Menu Changes · Busy <warning>

Page 165 of the Lexmark M412 user manual — 153 Status Messages
Page 165 · click to enlarge
Page 165

Status Message Meaning and Actions Allowed While Message Displays

The printer is deleting one or more Print and Hold jobs. This message displays if you selected Delete All Jobs or DELETE A JOB, and there are no other print jobs selected for printing.

Queuing and Deleting Jobs

The printer is deleting one or more Print and Hold jobs and printing one or more Print and Hold jobs. This message displays if one or more print jobs are selected for deletion in the CONFIDENTIAL JOB and HELD JOBS menu items, and one or more print jobs are selected for printing.

No button actions are possible while either of these messages displays.

See Delete All Jobs on page 63 and on page 68 or DELETE A JOB on page 63 and on page 68 for more information.

Disabling Menus This message briefly displays after the operator panel menus have been disabled. See “Disabling the Operator Panel Menus” on page 41 for more information.

No button actions are possible while this message displays.

Enabling Menus If the operator panel menus are disabled, this message briefly displays after they are enabled. See “Disabling the Operator Panel Menus” on page 41 for more information.

No button actions are possible while this message displays.

Flushing Buffer The printer is flushing corrupted print data and discarding the current print job.

No button actions are possible while this message displays.

Formatting Disk The hard disk option is formatting.

This message also displays if you select the Discard value for the Buffered Jobs menu item in the CONFIG MENU.

No button actions are possible while this message displays.

Formatting Flash DO NOT POWER OFF

The flash memory option is formatting.

No button actions are possible while this message displays.

Invalid Network 1 Code

This message displays if the code in the optional internal print server (also called an internal network adapter or INA) has not been programmed or if the code is not valid. You can download network code while this message displays.

When this message appears, the Ready and Busy messages do not display until valid code is programmed into the optional internal print server.

No button actions are possible while this message displays.

Menus Disabled The printer menus are disabled. This message displays when Menu> or <Menu is pressed.

See “Disabling the Operator Panel Menus” on page 41 for more information.

No button actions are possible while this message displays.

153 Status Messages

Deleting Jobs

Page 166 of the Lexmark M412 user manual — 154 Chapter 6: Understanding Printer Messages
Page 166 · click to enlarge
Page 166

Status Message Meaning and Actions Allowed While Message Displays

The optional internal print server is being reset. The Network 1 Setup menu item in the NETWORK MENU is not available while this message displays.

No button actions are possible while this message displays.

Not Ready The printer is in the Not Ready state, which means it is not ready to receive or process data.

  • Press Go to take the printer out of the Not Ready state.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

The printer is running the normal series of start-up tests after it is powered On (|). When the tests are complete, the printer returns to the Ready state.

No button actions are possible while this message display.

The printer is in Power Saver mode.

  • Press Go to take the printer out of Power Saver mode.
  • Press Menu> or <Menu to enter the menus.
  • Press Stop to take the printer offline. The Not Ready message displays. No data is processed. Press Go to return the printer to Power Saver .

154 Chapter 6: Understanding Printer Messages

Network Card Busy · Performing Self Test · Power Saver <warning>

Page 167 of the Lexmark M412 user manual — 155 Status Messages
Page 167 · click to enlarge
Page 167

Status Message Meaning and Actions Allowed While Message Displays

The printer is processing or printing a directory of all files stored in the flash memory option or on the hard disk option.

The printer is processing or printing a list of all available fonts for the selected printer language.

Printing Job Accounting Stat

The printer is processing or printing the Job Accounting Statistics.

The printer is processing or printing the menu settings page. See “Printing the Menu Settings Page” on page 39 for more information.

The message displays until the function completes and the page prints.

  • Press Stop to take the printer offline. The Not Ready message displays. No more data is processed, but all print material in the printer paper path prints. Press Go to return to the previous message.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

Printing Quality Test Pages

The printer is formatting the Print Quality Test Pages once Prt Quality Pgs is selected in the CONFIG MENU. Once the pages start printing, the Busy message displays.

No button actions are possible while this message displays.

For more information about these pages, see Prt Quality Pgs on page 106.

Program Flash DO NOT POWER OFF

The printer is storing resources, fonts or macros, in the flash memory option. If infor- mation is written to the flash memory option and to the hard disk option at the same time, the Program Flash message displays.

No button actions are possible while this message displays.

Programming Disk DO NOT POWER OFF

The printer is storing resources, fonts or macros, on the hard disk option. If information is written to the flash memory option and to the hard disk option at the same time, the Program Flash message displays.

No button actions are possible while this message displays.

155 Status Messages

Printing Directory List · Printing Font List · Printing Menu Settings

Page 168 of the Lexmark M412 user manual — 156 Chapter 6: Understanding Printer Messages
Page 168 · click to enlarge
Page 168

Status Message Meaning and Actions Allowed While Message Displays

The printer is processing one or more Print and Hold jobs selected for printing. This message displays if you selected PRINT A JOB, Print All Jobs, or PRINT COPIES and no jobs are selected for deletion.

Queuing and Deleting Jobs

The printer is processing one or more Print and Hold jobs selected for printing and deleting one or more Print and Hold jobs. This message displays if you selected one or more jobs to print using PRINT A JOB, Print All Jobs, or PRINT COPIES values in the CONFIDENTIAL JOB or HELD JOBS menu items, and one or more jobs are selected for deletion.

No button actions are possible while either of these messages displays.

See PRINT A JOB on page 62 and on page 67, Print All Jobs on page 62 and on page 67, or PRINT COPIES on page 64 and on page 69 for more information.

The printer is ready to receive and process data.

  • Press Menu> or <Menu to take the printer out of the Ready state and enter the menus.
  • Press Stop to take the printer offline. The Not Ready message displays. No data is processed. Press Go to return the printer to the Ready state.

For more information, refer to the Technical Reference.

The printer is ready and Hex Trace mode is active. Hex Trace isolates the source of a print job problem. When Hex Trace is selected, all data sent to the printer prints in hexadecimal and character representation. Control codes print, but do not execute.

  • Power Off (O) the printer to exit Hex Trace .
  • Press Stop to take the printer offline. The Not Ready message displays, and no data is processed. Press Go to return the printer to the Ready state.
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

156 Chapter 6: Understanding Printer Messages

Queuing Jobs · Ready <warning> · Ready Hex <warning>

Page 169 of the Lexmark M412 user manual — 157 Status Messages
Page 169 · click to enlarge
Page 169

Status Message Meaning and Actions Allowed While Message Displays

The resolution of the page is reduced from 600 dots per inch (dpi) to 300 dpi to prevent a 38 Memory Full error. Res Reduced displays for the duration of the current job. The printer indicator light blinks while the printer is processing data.

  • Press Stop to take the printer out of the Res Reduced state. The Not Ready message displays. Press Go to return to Res Reduced .
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .

The printer is deleting any print jobs in process and restoring all printer settings to user defaults.

No button actions are possible while this message displays.

The printer is restoring factory defaults. Factory defaults are restored by selecting Factory Defaults in the UTILITIES MENU or by selecting Factory Defaults in the CONFIG MENU.

See page 57 or page 107 for details about which printer settings are affected.

No button actions are possible while this message displays.

Waiting displays when one of the following occurs:

  • The printer has received a page of data to print, but is waiting for an End of Job command, Form Feed command, or for additional data. Waiting displays until the Print Timeout occurs or additional data is received.
  • When Collation is set to On , but the print job has not been canceled. Termination of the print job is required before page collated copies print.
  • Press Go to print the contents of the buffer.
  • Press Stop to take the printer out of the Waiting state. The Not Ready message displays. Press Go to return to Waiting .
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

157 Status Messages

Show 4 more labels / short text on this page
Res Reduced <warning> · Resetting the Printer · Restoring Factory Defaults · Waiting <warning>
Page 170 of the Lexmark M412 user manual — 158 Chapter 6: Understanding Printer Messages
Page 170 · click to enlarge
Page 170

Ready Tray 1 Missing

In this example, Tray 1 Missing is the warning message.

The following table lists messages that appear on the sec- ond line of the operator panel display. If none of the fol- lowing conditions exist, line 2 of the operator panel display is blank.

Fax 1 The printer is processing a fax through the optional interface.

Infrared 1 The optional infrared interface is the active communication link.

LocalTalk 1 The optional LocalTalk interface is the active communication link.

Network 1 The optional network interface is the active communication link.

Parallel The standard parallel interface is the active communication link.

Parallel 1 The optional parallel interface is the active communication link.

Serial 1 The optional serial interface is the active communication link.

Tray 1 Missing The 250-sheet input tray is missing.

Tray 1 Missing is available only if the optional 500-sheet drawer is installed. See “Optional 500-Sheet Drawer” on page 223 for more information.

USB The standard USB interface is the active communication link.

USB 1 The optional USB interface is the active communication link.

158 Chapter 6: Understanding Printer Messages

Status Message Meaning

Page 171 of the Lexmark M412 user manual — 159 Attendance Messages
Page 171 · click to enlarge
Page 171

Attendance

Attendance messages indicate printer errors that you must resolve before you can continue printing. The mes- sages are listed in numerical then alphabetical order.

Messages

Attendance Message Meaning and Required Action

34 Short Paper The printer determines the paper length is too short to print the formatted data. This occurs when the printer does not know the actual paper size loaded in tray. This message also displays if you select Universal as a Paper Size setting and use print material too short for the page format.

  • Press Go to clear the message and continue printing.
  • Make sure the Paper Size setting in the PAPER MENU is correct for the size print material you are using. If the MP Feeder Size setting is set to Universal , make sure your print material is large enough.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

35 Res Save Off Deficient Memory

The printer lacks the memory needed to enable Resource Save. This message usually indicates that too much memory is allocated for one or more of the printer link buffers.

To enable Resource Save after this message displays:

  • Install additional memory, or
  • Set the link buffer back to Auto , and exit the menus to activate the link buffer changes. When Ready displays, enable Resource Save from the SETUP MENU .

Press Go to disable Resource Save and continue printing.

159 Attendance Messages

Page 172 of the Lexmark M412 user manual — 160 Chapter 6: Understanding Printer Messages
Page 172 · click to enlarge
Page 172

Attendance Message Meaning and Required Action

37 Insufficient Collation Area

The printer memory used to store pages of data is too full to collate the rest of the print job.

  • Press Go to clear the message, print the portion of the job already in memory, and begin collating the rest of the job.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

37 Insufficient Defrag Memory

The printer memory used to store undeleted flash resources is too full to perform the flash memory defragment operation.

  • Press Go to clear the message.

To perform the defragment operation, you can:

  • Delete fonts, macros, and other data in printer RAM.
  • Install additional printer memory.

The printer memory contains Print and Hold jobs, and is too full to continue processing the current job.

Held Jobs may be lost. Go/Stop?

  • Press Go to clear the messages and continue printing the current job. The printer frees memory by deleting all Print and Hold jobs. If the current job is a Print and Hold job, it is not deleted.
  • Press Stop to clear the messages and continue printing the job. However, some data may not print or may not print correctly.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

160 Chapter 6: Understanding Printer Messages

37 Insufficient Memory

Page 173 of the Lexmark M412 user manual — 161 Attendance Messages
Page 173 · click to enlarge
Page 173

Attendance Message Meaning and Required Action

38 Memory Full The printer is processing data, but the memory used to store pages is full.

  • Press Go to clear the message and continue printing the job. However, some data may not print or may not print correctly.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

After resetting the printer, reduce the complexity of the print job and send it to print again. To simplify the print job:

  • Reduce the amount of text or graphics on a page.
  • Reduce the print resolution.
  • Delete unnecessary downloaded fonts or macros.

Install additional printer memory to avoid future 38 Memory Full errors.

39 Complex Page The page may not print correctly because the amount of text, graphics, or print infor- mation on the page is very complex.

  • Set Page Protect in the SETUP MENU to On and send the print job again.
  • Press Go to clear the message and continue printing the job. However, some data may not print or may not print correctly. Try to simplify the print job.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

The printer detects a defective flash memory option. This message appears when you power On (|) the printer, or during format and write to flash operations.

Press Go to clear the message and continue printing. You must install a different flash memory option before you can perform any flash memory operations.

161 Attendance Messages

51 Defective Flash

Page 174 of the Lexmark M412 user manual — 162 Chapter 6: Understanding Printer Messages
Page 174 · click to enlarge
Page 174

Attendance Message Meaning and Required Action

52 Flash Full There is not enough free space in the flash memory option to store the data that was sent.

  • Press Go to clear the message and continue printing. Downloaded fonts and macros not previously stored in flash memory are deleted.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

The printer detects an unformatted flash memory option. This message appears when you power On (|) the printer.

You must format the flash memory option before you can perform any flash memory operations. To format the flash memory option, select Format Flash from the UTILITIES MENU.

Press Go to clear the message and continue printing. If the error message remains, the flash memory option may be defective and need replacing.

162 Chapter 6: Understanding Printer Messages

53 Unformatted Flash

Page 175 of the Lexmark M412 user manual — 163 Attendance Messages
Page 175 · click to enlarge
Page 175

Attendance Message Meaning and Required Action

54 Serial Option 1 Error

A serial interface error is detected (framing or parity) on the optional serial port. This error usually indicates the serial link has not been set up correctly. When the serial error displays, the reporting of other serial errors is suppressed until interface parameters are changed or the printer is reset.

54 Std Par ENA Connection Lost

Displays only during the printer power-on cycle to indicate the connection to an external print server (also called an external network adapter or ENA) is lost.

54 Par 1 ENA Connection Lost

54 Ser 1 Fax Connection Lost

The serial port is configured to receive fax data, but the connection to the external modem has been lost. If the Fax Port menu item in the FAX MENU is not set to Disabled, the printer automatically assumes a modem is connected for fax processing. See “Fax Menu” on page 102 for more information.

Check the interface to:

  • Verify you are using the correct cable.
  • Make sure the serial interface parameters (protocol, baud, parity, data bits) are correct.

If one of these messages display:

  • Press Go to clear the message and continue printing the job. However, some data may not print or may not print correctly.
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

54 Network 1 Software Error

A network port is installed, but the software cannot establish communications with the port.

  • Press Go to clear the message. The printer disables communications with the network.

163 Attendance Messages

Page 176 of the Lexmark M412 user manual — 164 Chapter 6: Understanding Printer Messages
Page 176 · click to enlarge
Page 176

Attendance Message Meaning and Required Action

55 Insufficient Fax Buffer

The printer link buffer used to process data is too full to receive an incoming fax.

This message usually displays when the printer is busy receiving, processing, or printing data from a host interface connection while fax data is being received through a serial interface port configured for fax processing.

  • Press Go to clear the message and continue printing the job. However, some data may not print or may not print correctly.
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

After this message displays, the connection between the printer and the sending fax machine is broken. The printer will not accept additional fax data until sufficient fax buffer space is made available. However, any fax data stored in the fax buffer is printed. See “Fax Menu” on page 102 for more information.

56 Serial Port 1 Disabled

Data is sent to the printer across the serial port, but the serial port is disabled. When the serial error displays, the reporting of other serial errors is suppressed until the menus are entered or the printer is reset.

If this message displays:

  • Make sure the Serial Buffer menu item in the SERIAL MENU is not set to Disabled .
  • Press Go to clear the message. The printer discards any data received on the serial port.
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

56 Std Parallel Port Disabled

Data is sent to the printer through the parallel port, but the parallel port is disabled. When the error displays, the reporting of other errors is suppressed until the menus are entered or the printer is reset.

56 Parallel Port 1 Disabled

If one of these messages displays:

  • Make sure the Parallel Buffer menu item in the PARALLEL MENU is not set to Disabled .
  • Press Go to clear the message. The printer discards any data received through the parallel port.
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

164 Chapter 6: Understanding Printer Messages

Page 177 of the Lexmark M412 user manual — 165 Attendance Messages
Page 177 · click to enlarge
Page 177

Attendance Message Meaning and Required Action

58 Too Many Flash Options

The printer detects more than one flash option installed. Your printer can only have one flash option installed.

  • Press Go to clear the error.
  • Turn the printer power Off (O). Remove the extra option. Turn the printer power On (|). See “Removing Memory Options” on page 210 for more information.

The printer detects a defective hard disk option. This message appears when you power On (|) the printer, or during hard disk format or write operations.

Press Go to clear the message and continue printing. You must install a different hard disk option before you can perform any hard disk operations.

62 Disk Full There is not enough free space in the hard disk option to store the data that was sent.

  • Press Go to clear the message and continue processing. Any information not previously stored in the hard disk option is deleted.
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

The printer detects an unformatted hard disk option. This message appears when you power On (|) the printer.

You must format the hard disk option before you can perform any hard disk operations. To format the hard disk option, select Format Disk from the UTILITIES MENU.

Press Go to clear the message and continue printing. If the error message remains, the hard disk option may be defective and need replacing. Hard disk operations are not allowed until the defective disk is replaced and the new one is formatted.

70. 79 messages Reserved for messages relating to the optional internal print server.

For more information, refer to the online documentation that comes with your printer. Also, refer to the documentation that comes with the optional internal print server.

200 Paper Jam Remove Cartridge

The printer detects a paper jam. Open the upper front door, remove the print cartridge, and gently remove the jammed print material. Reinstall the print cartridge and close the upper front door. See “200 and 201 Paper Jam - Remove Cartridge” on page 184 for more information.

Press Go to clear the message and continue printing. The printer prints a new copy of the page that jammed if Jam Recovery is set to On or Auto. However, the Auto setting does not guarantee the page will print.

201 Paper Jam Remove Cartridge

The printer detects a paper jam. Open the upper front door, remove the print cartridge, and gently remove the jammed print material. Reinstall the print cartridge and close the upper front door. See “200 and 201 Paper Jam - Remove Cartridge” on page 184 for more information.

Press Go to clear the message and continue printing. The printer prints a new copy of the page that jammed if Jam Recovery is set to On or Auto. However, the Auto setting does not guarantee the page will print.

165 Attendance Messages

61 Defective Disk · 63 Unformatted Disk

Page 178 of the Lexmark M412 user manual — 166 Chapter 6: Understanding Printer Messages
Page 178 · click to enlarge
Page 178

Attendance Message Meaning and Required Action

202 Paper Jam Open Rear Door

The printer detects a paper jam behind the rear output bin door. Open the rear output bin door and gently remove the jammed print material. Close the rear output bin door. See “202 Paper Jam - Open Rear Door” on page 186 for more information.

Press Go to clear the message and continue printing. The printer prints a new copy of the page that jammed if Jam Recovery is set to On or Auto. However, the Auto setting does not guarantee the page will print.

Once the print job is complete, close the rear output bin door.

203 Paper Jam Short Paper

The printer detects a paper jam behind the rear output bin door. Open the rear output bin door and gently remove the jammed print material. Leave the rear output bin door open. Set PAPER LENGTH to Short from the operator panel. See “203 Paper Jam - Short Paper” on page 190 for more information.

Press Go to clear the message and continue printing. The printer prints a new copy of the page that jammed if Jam Recovery is set to On or Auto. However, the Auto setting does not guarantee the page will print.

Once the print job is complete, close the rear output bin door.

250 Paper Jam Check MP Feeder

The printer detects a paper jam in the multipurpose feeder. If the print material is visible from the front of the multipurpose feeder, pull it out gently. If only a small portion is visible, open the upper front door, remove the print cartridge, and remove the jammed print material. Reinstall the cartridge and close the upper front door. See “250 Paper Jam - Check MP Feeder” on page 192 for more information.

Press Go to clear the message and continue printing. The printer prints a new copy of the page that jammed if Jam Recovery is set to On or Auto. However, the Auto setting does not guarantee the page will print.

These service messages indicate printer failures that may require service.

When a service message occurs, the printer immediately stops printing. Turn the printer power Off (O), wait for about 10 seconds, and then turn the printer power On (|).

If the service message recurs, call for service and report the message number and description of the problem.

166 Chapter 6: Understanding Printer Messages

900-999 service messages

Page 179 of the Lexmark M412 user manual — 167 Attendance Messages
Page 179 · click to enlarge
Page 179

Attendance Message Meaning and Required Action

The printer requests a different print material than what is loaded in the tray or set in the PAPER SIZE or PAPER TYPE menus.

<Custom Type Name> <size> <type><size>

Line 1 displays the input source (<input source>), which is one of the following items:

  • Tray 1
  • Tray 2
  • MP Feeder

Line 2 displays one of the following items:

  • <Custom Type Name> : A user-defined name for Custom Type 1 through 6. The name is truncated to fit on the operator panel display. Use the MarkVision utility to create Custom Type names. See “Introducing MarkVision” on page 25 for more information.
  • <size> : If the requested type matches the type currently in the paper source and the custom type name has not been defined by you, only the print material or envelope size ( <size> ) displays. The name is truncated to fit on the operator panel display.
  • <type><size> : The requested type ( <type> ) is a type other than a custom type. The requested size ( <size> ) of print material or envelope displays. The type and size names are truncated to fit on the operator panel display.

If you are using Tray 1 or Tray 2 when this message displays, you can:

  • Load the requested size and type print material in the input source. Press Go to continue printing.
  • Press Select to clear the message and continue printing on the print material installed in the input source.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

If you are using the multipurpose feeder when this message displays, you can:

  • Load the requested size and type print material in the multipurpose feeder. The printer will clear the message and automatically continue printing.
  • If the correct print material is already loaded in the multipurpose feeder, press Go .
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

167 Attendance Messages

Change <input source>

Page 180 of the Lexmark M412 user manual — 168 Chapter 6: Understanding Printer Messages
Page 180 · click to enlarge
Page 180

Attendance Message Meaning and Required Action

Check Tray 2 Connection

The printer has lost communication with the optional 500-sheet drawer.

Communication may be lost if the optional 500-sheet drawer was removed from the printer, for example, to clear a paper jam. The optional 500-sheet drawer may still be attached to the printer, but may not be fully connected or may be experiencing a hardware failure.

If this message displays:

  • Reestablish communication by removing the optional 500-sheet drawer and reattaching it to the printer. See “Installing the Optional Drawer” on page 223 for more information. When the optional 500-sheet drawer is recognized by the printer, the message clears.
  • In case of a hardware failure, turn the printer power Off (O) and back On (|). If the error recurs, turn the printer power Off (O), remove the optional 500-sheet drawer, and call for service.

Close Door or Insert Cartridge

The upper front door is open or the print cartridge is not installed.

Close the door or install the print cartridge, then close the door.

Delete All Jobs. Go/Stop?

The printer requests confirmation to delete all Print and Hold jobs. This message displays if Delete All Jobs is selected from the CONFIDENTIAL JOB menu item or from the HELD JOBS menu item.

  • Press Go to continue. The printer deletes all Print and Hold jobs.
  • Press Stop to cancel this operation.

See CONFIDENTIAL JOB on page 60 or HELD JOBS on page 65 for more information.

Enter PIN=____

The printer requests you enter a four-digit Personal Identification Number (PIN) associated with your Confidential Job once you enter the CONFIDENTIAL JOB menu item on the operator panel. You use the operator panel buttons to enter the number.

See “Entering a Personal Identification Number (PIN)” on page 111 for more infor- mation.

Files will be Lost. Go/Stop?

This message displays when you change the Job Buffer Size setting on the operator panel. The printer must reformat the hard disk option. The message asks for confir- mation to continue and erase all files on the hard disk option.

  • Press Go to continue. The hard disk option formats and the specified job buffer partition is created. The message Format Disk displays while the hard disk option formats.
  • Press Stop to cancel this operation.

168 Chapter 6: Understanding Printer Messages

Page 181 of the Lexmark M412 user manual — 169 Attendance Messages
Page 181 · click to enlarge
Page 181

Attendance Message Meaning and Required Action

Insert Tray 1 This message displays when the printer needs to select print material from Tray 1 (250-sheet input tray). The printer is requesting the 250-sheet input tray be inserted so it can continue printing. This may happen if you remove the 250-sheet input tray to fill it with print material while a job is printing.

To avoid this message, press Stop, wait for the job to stop printing, and then remove the 250-sheet input tray to fill it.

When this message occurs:

  • Insert Tray 1 to clear the message and continue printing the job.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

Install Tray 2 or Cancel Job

The printer has lost communication with the optional 500-sheet drawer support unit. The support unit is not properly attached to the printer when you have sent a job to print.

When this message occurs:

  • Reattach the printer to the optional 500-sheet drawer support unit to clear the message and continue printing the job.

1 Lift the printer by the handholds or ask someone to help you lift the printer. Make sure your fingers are not under the printer when you set it down.

2 Place the printer on top of the support unit. Make sure the edges of the printer and the support unit are aligned properly.

  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

169 Attendance Messages

Page 182 of the Lexmark M412 user manual — 170 Chapter 6: Understanding Printer Messages
Page 182 · click to enlarge
Page 182

Attendance Message Meaning and Required Action

The printer is trying to feed print material from an input source it detects is empty.

<Custom Type Name> <size> <type><size>

Line 1 displays the input source (<input source>), which is one of the following items:

  • Tray 1
  • Tray 2
  • MP Feeder

Line 2 displays one of the following items:

  • <Custom Type Name> : A user-defined name for custom type 1 through 6. The name is truncated to fit on the operator panel display. Use the MarkVision utility to create custom type names. See “Introducing MarkVision” on page 25 for more information.
  • <size> : If the requested type matches the type currently in the tray and the custom type name has not been defined by you, only the print material or envelope size displays. The name is truncated to fit on the operator panel display.
  • <type><size> : The requested type ( <type> ) is a type other than a custom type. The requested size <size> of print material or envelope displays. The type and size names are truncated to fit on the operator panel display.

If you are using Tray 1 or Tray 2 when this message displays, you can:

  • Load the requested size and type print material in the input source. Press Go to continue printing.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

If you are using the multipurpose feeder when this message displays, you can:

  • Load the requested size and type print material in the multipurpose feeder. The printer will clear the message and automatically continue printing.
  • If the correct print material is already loaded in the multipurpose feeder, press Go .
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

170 Chapter 6: Understanding Printer Messages

Load <input source>

Page 183 of the Lexmark M412 user manual — 171 Attendance Messages
Page 183 · click to enlarge
Page 183

Attendance Message Meaning and Required Action

The printer requests print material to be manually fed from the multipurpose feeder.

<Custom Type Name> <size> <type><size>

Line 2 displays one of the following items:

  • <Custom Type Name> : A user-defined name for custom type 1 through 6. The name is truncated to fit on the operator panel display. Use the MarkVision utility to create custom type names. See “Introducing MarkVision” on page 25 for more information.
  • <size> : If the requested type matches the type currently in the tray and the custom type name has not been defined by you, only the print material or envelope size displays. The name is truncated to fit on the operator panel display.
  • <type><size> : The requested type ( <type> ) is a type other than a custom type. The requested size ( <size> ) of print material or envelope displays. The type and size names are truncated to fit on the operator panel display.

When this message displays you can:

  • Load the requested size or type of print material in the multipurpose feeder. The printer automatically clears the message and continues printing.
  • Press Go if the correct size and type print material is loaded in the multipurpose feeder.
  • Press Select to clear the message and print on the print material installed in Tray 1 or the optional Tray 2.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

No Jobs Found. Retry?

The Personal Identification Number (PIN) you entered is not a PIN associated with any Confidential Job in printer memory.

  • Press Go to enter another PIN.
  • Press Stop to exit the PIN entry prompt.

See “Entering a Personal Identification Number (PIN)” on page 111 for more infor- mation.

171 Attendance Messages

Load Manual

Page 184 of the Lexmark M412 user manual — 172 Chapter 6: Understanding Printer Messages
Page 184 · click to enlarge
Page 184

Attendance Message Meaning and Required Action

Open Rear Door The print material in the multipurpose feeder is 152.4 mm (6 in.) or less in length and the rear output bin door is not open.

When this message displays you can:

  • Open the rear output bin door to let the print material exit.
  • Cancel the current job. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Cancel Job appears on the second line of the operator panel display. Press Select .
  • Reset the printer. Press Menu> or <Menu . The JOB MENU displays. Press Menu> or <Menu until Reset Printer appears on the second line of the operator panel display. Press Select .

Operation Failed Jobs on Disk

This message displays when the printer receives a request to format the hard disk option or modify the Job Buffer Size setting and Print and Hold jobs are currently stored on the hard disk option.

Operation Failed Faxes on Disk

This message displays when the printer receives a request to format the hard disk option or modify the Job Buffer Size setting and fax jobs are currently stored on the hard disk option.

You cannot format the hard disk option or change the Job Buffer Size while the hard disk option contains Print and Hold jobs or fax jobs.

  • Press Go to continue. The request is ignored.

Print Jobs on Disk? Go/Stop?

This message displays when Print Job Buffering is enabled and the printer power is turned Off (O) while print jobs are spooled to the hard disk option. When the printer power is turned back On (|), it asks for confirmation to print the waiting jobs.

  • Press Go to print the jobs.
  • Press Return or Stop to delete all spooled jobs from the hard disk option without printing them.

172 Chapter 6: Understanding Printer Messages

Page 185 of the Lexmark M412 user manual — 173 Solving Printer Problems
Page 185 · click to enlarge
Page 185

7 Solving Printer

Problems

Sometimes printer problems are very easy to solve. When you have a problem, first make sure that:

  • The printer power cord is plugged into the printer and a properly grounded electrical outlet.
  • The printer power switch is On (|).
  • The electrical outlet is not turned off by any switch or breaker.
  • Other electrical equipment plugged into the outlet is working.
  • All options are properly installed.

If you have checked all of the above and still have a prob- lem, turn the printer power Off (O), wait for about 10 sec- onds, and then turn the printer power On (|). This often fixes the problem.

173 Solving Printer Problems

Page 186 of the Lexmark M412 user manual — 174 Chapter 7: Solving Printer Problems
Page 186 · click to enlarge
Page 186

The tables in this chapter define printing problems that may occur and what you can do to resolve them. If the suggested corrective action does not fix the problem, call your service representative.

Turn to the appropriate page for help with your printing problem:

Problem with... See page...

Other Problems and Questions 182

174 Chapter 7: Solving Printer Problems

Show 5 more labels / short text on this page
Display 175 · Print Quality 178 · Printing 176 · Network 181 · Option 180
Page 187 of the Lexmark M412 user manual — 175 Display Problems
Page 187 · click to enlarge
Page 187

Display Problems

Menus Disabled status message appears on the display.

The operator panel menus are disabled. To enable the menus:

  • Turn the printer power Off (O).
  • Press and hold Select and Return , and then turn the printer power On (|).
  • Release the buttons when Performing Self Test displays.

Once the printer finishes powering on, the CONFIG MENU displays.

  • Press Menu> until Panel Menus displays on the second line. Press Select .
  • Press Menu> until Enable displays on the second line. Press Select .

The Saved message briefly appears and then, the Enabling Menus displays.

The CONFIG MENU displays again with Panel Menu on the second line.

  • Press Menu> until Exit Config Menu displays on the second line. Press Select .

Activating Menu Changes briefly appears, and then Performing Self Test briefly appears. The printer returns to the Ready state.

If the operator panel menus are password protected, see your system adminis- trator.

Display shows only diamonds or is blank.

  • Turn the printer power Off (O), wait about 10 seconds, and turn the printer power On (|).
  • The Performing Self Test message appears on the operator panel display. When the test is completed, the Ready message displays.

If the messages do not display, turn the printer power Off (O) and call Lexmark Customer Support Center.

Menu settings changed from the operator panel have no effect.

Settings in the software application, the printer driver, or the printer utilities are overriding the settings in the operator panel.

  • Change the menu settings from the printer driver, the printer utilities, or the software application instead of the operator panel.
  • Disable the settings in the printer driver, the printer utilities, or the software application so you can change settings from the operator panel.

175 Display Problems

Problem Action

Page 188 of the Lexmark M412 user manual — 176 Chapter 7: Solving Printer Problems
Page 188 · click to enlarge
Page 188

Printing Problems

Job did not print or incorrect characters printed.

Make sure the Ready status message appears on the operator panel display before you send a job to print. Press Go to return the printer to the Ready status message.

Make sure there is print material loaded in the printer. Press Go to return the printer to the Ready status message.

Verify that the printer is using the correct printer language.

  • Verify that the correct printer driver is being used.
  • Make sure the parallel cable or USB cable is firmly plugged in at the back of the printer.
  • Check the cable connection. Make sure you are using the correct cable. If you use the parallel port, we recommend a IEEE 1284-compliant parallel cable such as Lexmark part number 1329605 (10 ft) or 1427498 (20 ft). If you use the USB port, we recommend the cable with Lexmark part number 12A2405 (2M).
  • If the printer is connected through a switch box, try a direct connection.
  • Verify that the correct paper size is selected through the operator panel, in the printer driver, or in the software application setting.
  • Make sure PCL SmartSwitch and PS SmartSwitch are set to On .
  • If a print spooler is used, verify that the spooler is not stalled.
  • If you print across a network or on a Macintosh, see “Network Printing Problems” on page 181.

Determine which host interface you are using. Print a menu settings page to verify that the current interface settings are correct. See “Printing the Menu Settings Page” on page 39 for more information.

If you are using serial interface:

  • Make sure Honor DSR is set to Off .
  • Check the protocol, baud, parity, and data bit settings. The settings on the printer and on the host computer should match.

You are connected to the USB port, but the printer will not print.

Make sure you are using Windows 98 or other USB-capable operating system supported by Lexmark.

176 Chapter 7: Solving Printer Problems

Problem Action

Page 189 of the Lexmark M412 user manual — 177 Printing Problems
Page 189 · click to enlarge
Page 189

Problem (continued) Action (continued)

Print material misfeeds or multiple feeds occur.

  • Make sure the print material you are using meets the specifications for your printer. See “Print Material Guidelines” on page 118 for more information.
  • Flex print material before loading it in any of the paper sources.
  • Make sure the print material is loaded correctly.
  • Make sure the paper width and length guides on the paper sources are adjusted correctly and are not too tight.
  • Do not overfill the paper sources.
  • Do not force print material into the multipurpose feeder when you load it; otherwise, it may skew or buckle.
  • Remove any curled print material from paper sources.
  • If there is a recommended print side for the print material, load the print material as described in “Print Material Guidelines” on page 118.
  • Load less print material in the input sources.
  • Turn the print material over or around and try printing again to see if feeding improves.
  • Do not mix print material types.
  • Do not mix reams of print material.
  • Remove the top and bottom sheets of a ream before loading the print material.
  • Load an input source only when it is empty.

You get unexpected page breaks. Check the Print Timeout setting in the SETUP MENU. Increase the setting. See Print Timeout on page 74 for more information.

Job prints from the wrong input source or on the wrong print material.

Check the PAPER TYPE setting in the PAPER MENU on the operator panel and in the printer driver. See PAPER TYPE on page 47 for more information.

Print material does not stack neatly in an output bin.

  • Turn the print material stack over in the tray or multipurpose feeder.
  • If the print material is exiting to the standard output bin, make sure the paper bail is installed correctly. See “Installing the Paper Bail” on page 11 for more information.

177 Printing Problems

Page 190 of the Lexmark M412 user manual — 178 Chapter 7: Solving Printer Problems
Page 190 · click to enlarge
Page 190

Print Quality

Problems

  • Print is too light.
  • Check the toner supply.
  • Change the Toner Darkness setting in the QUALITY MENU . See Toner Darkness on page 71 for more information.
  • If you are printing on an uneven print surface, change the PAPER WEIGHT and PAPER TEXTURE settings in the PAPER MENU . See PAPER TYPE on page 47 for more information.
  • Verify that the correct print material is being used.

Toner smears or print comes off the page.

  • If you are printing on an uneven print surface, change the PAPER TEXTURE and PAPER WEIGHT settings in the PAPER MENU . See PAPER TEXTURE on page 50 and PAPER WEIGHT on page 51 for more information.
  • Verify that the print material is within the printer specifications. See “Using Print Materials” on page 115 for more information.
  • If the problem continues, call Lexmark Customer Support Center.

Toner appears on the back of the printed page.

Toner is on the transfer roll. To help prevent this, do not load print material that is smaller than the page size of the job to be printed.

  • Open and close the printer upper front door to run the printer through its setup cycle and clean the transfer roll.
  • Replace the fuser cleaner. The fuser cleaner and replacement instructions are included in the box when you purchase a new print cartridge.

Toner fog or background shading appears on the page.

  • Check the print cartridge to make sure it is installed correctly. See “Installing the Print Cartridge” on page 5 for more information.
  • Change the print cartridge. See “Maintaining Your Printer” on page 193 for more information.
  • If the problem continues, change the charge roll. See “Ordering a Charge Roll Kit” on page 195 for more information.
  • Entire page is white.
  • Make sure the packaging material is removed from the print cartridge. See “Removing Print Cartridge Packaging” on page 2.
  • Check the print cartridge to be sure it is installed correctly. See “Installing the Print Cartridge” on page 5 for more information.
  • Check the toner supply.

178 Chapter 7: Solving Printer Problems

Problem Action

Page 191 of the Lexmark M412 user manual — 179 Print Quality Problems
Page 191 · click to enlarge
Page 191

Problem (continued) Action (continued)

  • Streaks appear on the page.
  • The toner may be low. Remove the cartridge. To utilize the remaining toner, shake the cartridge gently. Reinstall the same print cartridge. See “Installing the Print Cartridge” on page 5 for directions.
  • If you are using preprinted forms, make sure the ink can withstand temperatures of 200 ° C (392 ° F).
  • The printhead lens may need cleaning. See “Cleaning the Printhead Lens” on page 195 for directions.

Printing is too dark. Change the Toner Darkness setting in the QUALITY MENU. See Toner Darkness on page 71 for more information.

Characters have jagged or uneven edges.

  • Change the Print Resolution setting in the QUALITY MENU to 600 dpi . See Print Resolution on page 71 for more information.
  • Turn PQET in the QUALITY MENU to On . See PQET on page 72 for more information.
  • If you are using downloaded fonts, verify that the fonts are supported by the printer, the host computer, and the software application.

Image quality is poor. Resolution was automatically reduced. Reduce the complexity of the print job or add additional printer memory. See Res Reduced on page 157 for more information.

Part of all of the page is printed in black.

  • Check the print cartridge to see if it is installed correctly. See “Installing the Print Cartridge” on page 5 for more information.
  • If the charge roll has been replaced, verify that it has been installed correctly. Refer to the installation instructions that come with the charge roll kit. See “Ordering a Charge Roll Kit” on page 195 for more information.

The job prints, but the left and top margins are incorrect.

  • Make sure the PAPER SIZE setting is set correctly in the PAPER MENU . See PAPER SIZE on page 45 for more information.
  • Make sure the margins are set correctly in the software application you are using.
  • Check the Print Area setting in the SETUP MENU . Set the value to Normal . See Print Area on page 76 for more information.

179 Print Quality Problems

Page 192 of the Lexmark M412 user manual — 180 Chapter 7: Solving Printer Problems
Page 192 · click to enlarge
Page 192

Option Problems

Option does not operate correctly after it is installed or it quits working.

  • Turn the printer power Off (O), wait for about 10 seconds, and turn the printer power On (|). If this does not fix the problem, unplug the printer, and check the connection between the option and printer.
  • Print the menu settings page and check to see if the option is listed in the Installed Options list. If the option is not listed, reinstall it. See “Verifying the Installation of Options” on page 229 for more information.
  • Make sure the option is selected in the software application you are using.

For Macintosh users: Make sure the printer is set up in CHOOSER.

Option does not operate correctly after it is installed.

Optional Drawer: Make sure the connection between the optional 500-sheet drawer and the printer is secure. See “Optional 500-Sheet Drawer” on page 223 for more information.

Make sure the print material is loaded correctly. See “Loading Print Material” on page 124 for more information.

Flash Memory Option: Check to make sure the flash memory option is securely connected to the printer system board. See “Understanding Memory Options” on page 206 for more information.

Printer Memory Option: Check to make sure the printer memory option is securely connected to the printer system board. See “Understanding Memory Options” on page 206 for more information.

Hard Disk Option: Check to make sure the hard disk option is securely connected to the printer system board. See “Hard Disk Option” on page 212 for more information.

Hard Disk Adapter Card: Check to make sure the hard disk option is securely connected to the hard disk adapter card. Also check to make sure the hard disk adapter card is securely connected to the printer system board. See “Hard Disk Option” on page 212 for more information.

Internal Print Server Option: Check to make sure the optional internal print server (also called an internal network adapter or INA) is securely connected to the printer system board. See “Internal Print Server (Internal Network Adapter or INA)” on page 211 for more information.

The connection to the network is made through the network cable. Check that you have the correct cable, that it is securely connected, and that the network software is correctly set up. See the documentation that comes with your optional internal print server for more information.

Tri-Port Interface Option: Check to make sure the Tri-Port Interface option card is securely connected to the printer system board. See “Tri-Port Interface Option Card” on page 212 for more information.

For Macintosh users: Make sure the host computer is set to LocalTalk.

If you are using a phone wire connection, a terminator plug must be used.

180 Chapter 7: Solving Printer Problems

Problem Action

Page 193 of the Lexmark M412 user manual — 181 Network Printing Problems
Page 193 · click to enlarge
Page 193

Problem (continued) Action (continued)

Option does not operate correctly after it is installed. (continued)

Infrared AdapterIf infrared communication stops or does not occur, check the following:
  • Communication distance: The distance between the two infrared ports should be 3 meters (10 ft.) or less. If communication does not occur between ports, move the ports closer together.
  • Make sure both ports are stable. Make sure the computer is on a level surface.
  • Make sure the angle of communication between the two infrared ports is within 15 degrees of either side of an imaginary line drawn between the two infrared ports.
  • Make sure there is no bright light, such as direct sunshine, interfering with communication.
  • Make sure no objects are placed between the two infrared ports.

Parallel/USB Interface Option: Check to make sure the parallel/USB interface option card is securely connected to the printer system board. See “Parallel/USB Interface Option Card” on page 215 for more information.

Network Printing

Problems

Job did not print or incorrect characters printed.

If you are using a Lexmark internal print server or external print server, verify that it is set up properly and the network cable is connected.

For Novell users:

  • Make sure the netware.drv file is dated October 24, 1994 or later.
  • Make sure the NT (no tabs) flag is included in the capture statement.

For Macintosh users:

  • The printer may need an optional internal print server to allow Macintosh connection.
  • Verify that the printer is set up correctly in CHOOSER.

181 Network Printing Problems

Problem Action

Page 194 of the Lexmark M412 user manual — 182 Chapter 7: Solving Printer Problems
Page 194 · click to enlarge
Page 194

Other Problems

and Questions

How do I get updated printer drivers or utilities?

See “Introducing MarkVision” on page 25 for more information.

How do I attach a serial cable to the printer?

Your printer requires an optional adapter to allow serial attachment. The Tri-Port interface option card supports serial RS-232C/RS-422A. See “Tri-Port Interface Option Card” on page 212 for more information.

Where are the printer escape codes listed?

The CD that was shipped with your printer contains an Adobe Acrobat file with a complete list of Printer Command Language (PCL) escape codes.

182 Chapter 7: Solving Printer Problems

Problem Action

Page 195 of the Lexmark M412 user manual — 183 Clearing Jams
Page 195 · click to enlarge
Page 195

8 Clearing Jams

By carefully selecting print materials and loading them properly, you should be able to avoid most paper jams. If paper jams do occur, complete the steps in the following sections. If paper jams occur frequently, make sure you see “Avoiding Paper Jams” on page 137.

To clear paper jam attendance messages, you must remove all jammed print material from the paper path.

Press Go to resume printing. If Jam Recovery is set to On or Auto, the printer prints a new copy of the page that jammed. However, the Auto setting does not guarantee the page will print.

Refer to the appropriate page for help with clearing paper jams.

If the following error message displays... See page...

200 Paper Jam - Remove Print Cartridge 184

201 Paper Jam - Remove Print Cartridge 184

202 Paper Jam - Open Rear Door 186

203 Paper Jam - Short Paper 190

250 Paper Jam - Check MP Feeder 192

183 Clearing Jams

Page 196 of the Lexmark M412 user manual — 184 Chapter 8: Clearing Jams
Page 196 · click to enlarge
Page 196

Possible Paper

The following illustration shows the path that print mate- rial travels through the printer. The path varies depending on the input source and exit selection (output bin). The jam areas are also shown.

Jam Areas

202 Paper Jam 250 Paper Jam

200 and 201 Paper Jam - Remove

Print material is jammed in the area under the print cartridge. This requires removing the print cartridge from the printer. With a 201 attendance message, the jam is far- ther back in the printer, so you need to reach in farther to remove the jammed print material.

Cartridge

1 Open the upper front door.

2 Remove the print cartridge.

See page 2 for instructions on removing the print cartridge.

184 Chapter 8: Clearing Jams

203 Paper Jam · 201 Paper Jam · 200 Paper Jam

Page 197 of the Lexmark M412 user manual — 185 Possible Paper Jam Areas
Page 197 · click to enlarge
Page 197

3 Notice that in some instances the ends of the print material are not visible.

Lexmark M412 — Possible Paper Jam Areas diagram (page 197)
Fig. 61 · Possible Paper Jam Areas

4 Gently pull the right side of the print material until the upper right corner is loose.

Lexmark M412 — Possible Paper Jam Areas diagram (page 197)
Fig. 62 · Possible Paper Jam Areas

5 With both hands, pull the print material up to the right and then out.

6 Reinstall the print cartridge. (See page 5 for instructions on reinstalling the print cartridge.)

7 Close the upper front door.

185 Possible Paper Jam Areas

Page 198 of the Lexmark M412 user manual — 186 Chapter 8: Clearing Jams
Page 198 · click to enlarge
Page 198

202 Paper Jam - Open Rear Door

Jams in the following areas cause a 202 attendance mes- sage. Jams in these areas require opening the printer rear output bin door and the upper front door:

  • The print material jams before reaching the standard output bin. See “Before Reaching the Standard Output Bin” as follows.
  • The print material jams after it starts into the standard output bin, but before it exits completely into the bin. See “Exiting to the Standard Output Bin” on page 189.

Before Reaching the Standard Output Bin

The print material jams before reaching the standard output bin.

Lexmark M412 — Before Reaching the Standard Output Bin diagram (page 198)
Fig. 63 · Before Reaching the Standard Output Bin

1 Locate the handhold on the rear output bin door and pull it toward you.

The rear output bin door opens and drops back toward you. If you need help, see “Using the Rear Output Bin” on page 134.

186 Chapter 8: Clearing Jams

Page 199 of the Lexmark M412 user manual — 187 Possible Paper Jam Areas
Page 199 · click to enlarge
Page 199

2 Determine how to remove the jammed print material based on what part of the print material is visible.

Lexmark M412 — 202 Paper Jam - Open Rear Door diagram (page 199)
Fig. 64 · 202 Paper Jam - Open Rear Door

– If the middle of the sheet of print material is visible, but not the ends, grasp the print material on both sides and gently pull it straight out toward you.

187 Possible Paper Jam Areas

Page 200 of the Lexmark M412 user manual — 188 Chapter 8: Clearing Jams
Page 200 · click to enlarge
Page 200
Lexmark M412 — 202 Paper Jam - Open Rear Door diagram (page 200)
Fig. 65 · 202 Paper Jam - Open Rear Door

– If an end of the print material is visible, pull the print material straight out toward you.

3 Close the rear output bin door.

188 Chapter 8: Clearing Jams

Page 201 of the Lexmark M412 user manual — 189 Possible Paper Jam Areas
Page 201 · click to enlarge
Page 201

Exiting to the Standard Output Bin

Print material jams before it exits completely into the standard output bin.

1 Pull the print material straight out. If there is resis- tance to the print material and it does not move immediately when you pull, stop pulling and con- tinue with the next step.

Lexmark M412 — Exiting to the Standard Output Bin diagram (page 201)
Fig. 66 · Exiting to the Standard Output Bin

2 Open the upper front door to release the fuser rollers.

Lexmark M412 — Exiting to the Standard Output Bin diagram (page 201)
Fig. 67 · Exiting to the Standard Output Bin

3 Pull the print material straight out.

189 Possible Paper Jam Areas

Page 202 of the Lexmark M412 user manual — 190 Chapter 8: Clearing Jams
Page 202 · click to enlarge
Page 202

203 Paper Jam - Short Paper

A 203 attendance message indicates print material less than 152.4 mm (6 in.) in length has attempted to exit the standard output bin.

A jam in this area requires that the rear output bin door be opened.

Lexmark M412 — 203 Paper Jam - Short Paper diagram (page 202)
Fig. 68 · 203 Paper Jam - Short Paper

1 Locate the handhold on the rear output bin door and pull it toward you.

The rear output bin door opens and drops back toward you. If you need help, see “Using the Rear Output Bin” on page 134.

190 Chapter 8: Clearing Jams

Page 203 of the Lexmark M412 user manual — 191 Possible Paper Jam Areas
Page 203 · click to enlarge
Page 203
Lexmark M412 — 203 Paper Jam - ShortPaper diagram (page 203)
Fig. 69 · 203 Paper Jam - ShortPaper

If there is resistance to the print material and it does not move immediately when you pull, stop pulling. Remove the print cartridge, return to the back of the printer, and pull the print material out.

3 Leave the rear output bin door open to allow the job to finish printing.

4 Press Go to resume printing.

5 If you are going to print additional pages less than 152.4 mm (6 in.) in length, set Paper Length to Short.

191 Possible Paper Jam Areas

Page 204 of the Lexmark M412 user manual — 192 Chapter 8: Clearing Jams
Page 204 · click to enlarge
Page 204

250 Paper Jam - Check MP Feeder

The print material jams as it enters the printer from the multipurpose feeder.

Lexmark M412 — 250 Paper Jam - Check MP Feeder diagram (page 204)
Fig. 70 · 250 Paper Jam - Check MP Feeder

Pull the jammed print material straight out of the multi- purpose feeder toward you.

To avoid tearing, pull the jammed print material out gen- tly and slowly.

192 Chapter 8: Clearing Jams

Page 205 of the Lexmark M412 user manual — 193 Ordering a Print Cartridge
Page 205 · click to enlarge
Page 205

9 Maintaining Your Printer

Periodically, you will need to replace the print cartridge and clean the printer to maintain optimum print quality.

If several people are using the printer, you may want to designate a key operator to do the setup and maintenance of your printer. Refer printing problems and maintenance tasks to this key operator.

Ordering a Print

You need to have a new print cartridge available when the current one no longer prints satisfactorily. There are two recommended print cartridges specifically designed for your printer:

Cartridge

Printer Model Part Number Yield (Average) Coverage

Optra M410 or M412

17G0152 5,000 pages 5%

Optra M410 or M412

17G0154 15,000 pages 5%

193 Ordering a Print Cartridge

Page 206 of the Lexmark M412 user manual — 194 Chapter 9: Maintaining Your Printer
Page 206 · click to enlarge
Page 206

Storing the Print

Store the print cartridge in the original packaging until you are ready to install it.

Cartridge

Do not store the print cartridge in:

  • Temperatures greater than 40°C (104°F).
  • An environment with extreme changes in humidity or temperature.
  • Direct sunlight.
  • Dusty places.
  • A car for a long period of time.
  • An environment where corrosive gases are present.
  • An environment with salty air.

Replacing the Print Cartridge

Complete the following steps to replace the print cartridge. Refer to the documentation that comes with the print cartridge for detailed installation information.

1 Remove the used print cartridge.

2 Clean the printer.

3 Install the new print cartridge.

4 Replace the fuser cleaner.

Use the installation instructions that come in the box with your new print cartridge to complete steps 2 through 4.

5 Follow the instructions on the new print cartridge box to recycle the used print cartridge.

When you return a used print cartridge, you contribute to a worldwide recycling effort at no cost to you.

For best results, use Lexmark supplies with the printer.

194 Chapter 9: Maintaining Your Printer

Page 207 of the Lexmark M412 user manual — 195 Cleaning the Printhead Lens
Page 207 · click to enlarge
Page 207

Cleaning the Printhead Lens

Complete the following steps to clean the printhead lens:

1 Turn the printer power Off (O).

2 Open the upper and lower front doors.

3 Remove the print cartridge.

4 Gently wipe the printhead lens with a clean, dry lint-free cloth.

Lexmark M412 — Cleaning the Printhead Lens diagram (page 207)
Fig. 71 · Cleaning the Printhead Lens

5 Insert the print cartridge.

6 Close the upper and lower front doors.

7 Turn the printer power On (|).

Ordering a Charge Roll Kit

We recommend you order a new charge roll kit when toner fog or background shading appears on printed pages. See “Print Quality Problems” on page 178 for more information on toner fog and background shading.

Order Lexmark part number 4K00196. Installation instruc- tions are included in the kit.

If you’re in the U.S. or Canada, call 1-800-438-2468 for information about Lexmark Authorized Supplies Dealers in your area. In other countries, contact the place where you bought your printer.

195 Cleaning the Printhead Lens

Page 208 of the Lexmark M412 user manual — 196 Chapter 9: Maintaining Your Printer
Page 208 · click to enlarge
Page 208

196 Chapter 9: Maintaining Your Printer

Page 209 of the Lexmark M412 user manual — Hardware
Page 209 · click to enlarge
Page 209

10 Fax

Understanding the

If your printer has a Tri-Port interface option card installed and the serial interface port is not in use, you can use your printer to receive and print fax data.

Fax Port

The serial interface port is only available if a Tri-Port inter- face option card is installed in your printer. See “Tri-Port Interface Option Card” on page 212 for more information.

When you want to use the fax serial port for another pur- pose, you must first follow the instructions for disabling the fax port on page 200. If you decide to reactivate the fax port, make sure you follow the instructions for setting up the fax port on page 198.

Choosing

To use your printer serial port to process fax data, you need an external, class 1 fax modem. You can use virtually any brand, as long as it is a class 1 fax modem.

Hardware

197 Understanding the Fax Port

Page 210 of the Lexmark M412 user manual — 198 Chapter 10: Fax
Page 210 · click to enlarge
Page 210

Setting Up a

To use your printer serial port to process fax data:

Fax Port

1 Turn the printer power Off (O) and unplug the printer power cord.

Lexmark M412 — Fax Port diagram (page 210)
Fig. 72 · Fax Port

2 Turn the modem power Off and unplug the modem power cord.

3 Disconnect all cables from the back of the printer.

4 Connect the hardware. The end of the modem cable that connects to the serial port must be 25-pin.

The class 1 fax modem connects to the serial port of your printer. If you need additional help, refer to the class 1 fax modem documentation for details.

5 Reconnect all cables to the back of the printer.

6 Reconnect the power cords to the printer and the modem to properly grounded electrical outlets.

7 Turn the modem power On.

8 Turn the printer power On (|).

9 Once Ready displays, complete the following steps to configure the serial port for fax data:

a Press Menu> or <Menu to enter the menus.

b Press Menu> until FAX MENU appears on the first

line of the display.

c Press Select.

Fax Port appears on the second line of the display.

d Press Select to choose Fax Port.

198 Chapter 10: Fax

Printer Serial Port · Modem Cable

Page 211 of the Lexmark M412 user manual — 199 Resetting a Fax Port
Page 211 · click to enlarge
Page 211

e Press Menu> until Ser Option 1 appears on the

second line of the display.

f Press Select to choose Ser Option 1.

g Fax Port appears on the second line. Press Go.

Activating Menu Changes appears and remains on the display until the serial port is reset.

See “Fax Menu” on page 102 for more information.

Resetting a

If power to the modem is interrupted you must complete the following steps, in order, for your printer to process fax data:

Fax Port

1 Turn the printer power Off (O).

2 Turn the modem power On.

3 Turn the printer power On (|).

199 Resetting a Fax Port

Page 212 of the Lexmark M412 user manual — 200 Chapter 10: Fax
Page 212 · click to enlarge
Page 212

Disabling a

To disable the fax port and restore the printer serial port settings:

Fax Port

1 When Ready displays on the top line of the opera- tor panel display, press Menu> or <Menu to enter the menus.

2 Continue to press Menu> or <Menu until FAX MENU appears on the first line of the display.

3 Press Select.

Fax Port appears on the second line of the display.

4 Press Select to choose Fax Port.

5 Press Menu> until Disabled appears on the second line of the display.

Serial Option 1 displays on the second line of the dis- play.

6 Press Select to disable the fax port.

7 Press Go.

Activating Menu Changes appears and remains on the display until the printer restores the serial port settings.

8 Turn the modem power Off.

9 Turn the printer power Off (O).

10 Disconnect all system components from the modem.

11 Disconnect the modem cable from the printer serial port.

12 Turn the printer power On (|).

See “Fax Menu” on page 102 for more information.

200 Chapter 10: Fax

Page 213 of the Lexmark M412 user manual — 201 Accessing the Printer System Board
Page 213 · click to enlarge
Page 213

11 Memory and Option Cards

You can customize your printer memory capacity and con- nectivity. This chapter provides instructions for installing and removing each option. To install each option, you must first access the printer system board. This can be done from the left side of the printer.

Accessing the Printer System

Complete the following steps before installing printer memory, a flash memory option, or an option card.

Board

1 Turn the printer power Off (O) and unplug the printer power cord from the electrical outlet.

2 Disconnect all cables from the back of the printer.

201 Accessing the Printer System Board

Page 214 of the Lexmark M412 user manual — 202 Chapter 11: Memory and Option Cards
Page 214 · click to enlarge
Page 214
Lexmark M412 — Memory and Option Cards diagram (page 214)
Fig. 73 · Memory and Option Cards

3 Push the upper release latch to release the upper front door.

4 Push the lower release latch to release the lower front door.

5 Press the latches located inside the front of the printer to release the side door.

202 Chapter 11: Memory and Option Cards

Page 215 of the Lexmark M412 user manual — 203 Accessing the Printer System Board
Page 215 · click to enlarge
Page 215

6 Remove the side door and lay it aside.

Lexmark M412 — Memory and Option Cards diagram (page 215)
Fig. 74 · Memory and Option Cards

7 Loosen the six screws on the shield. Do not remove the screws.

203 Accessing the Printer System Board

Page 216 of the Lexmark M412 user manual — 204 Chapter 11: Memory and Option Cards
Page 216 · click to enlarge
Page 216
Lexmark M412 — Memory and Option Cards diagram (page 216)
Fig. 75 · Memory and Option Cards

8 Use the tabs located on the side of the shield to slide the shield up until the top three screws fit into the three keyholes on the shield.

9 Hold the shield by the tabs and lift it off.

10 Locate the appropriate connector for the option you are installing.

204 Chapter 11: Memory and Option Cards

Page 217 of the Lexmark M412 user manual — 205 Accessing the Printer System Board
Page 217 · click to enlarge
Page 217

11 See the appropriate section for instructions on installing the option.

– For a printer memory or flash memory option, see “Installing Memory Options” on page 207. – For an optional internal print server (also called an internal network adapter or INA), see “Internal Print Server (Internal Network Adapter or INA)” on page 211. – For a Tri-Port interface option card, see “Tri-Port Interface Option Card” on page 212. – For a hard disk option, see “Hard Disk Option” on page 212. – For a Parallel/USB interface option card, see “Parallel/USB Interface Option Card” on page 215.

205 Accessing the Printer System Board

Page 218 of the Lexmark M412 user manual — 206 Chapter 11: Memory and Option Cards
Page 218 · click to enlarge
Page 218

Understanding Memory Options

Because the steps required to install a printer memory option and a flash memory option card are the same, they are grouped together in this section. Details about the two option cards follow.

Printer Memory The printer memory option increases the printer sync dynamic random access memory (SDRAM). Additional printer memory allows the printer to print complex jobs and operate more efficiently.

Your printer has 4MB of standard printer memory. You can purchase printer memory cards having 4MB, 8MB, 16MB, 32MB, and 64MB of memory. You can install up to two optional printer memory cards in your printer, for a total of up to 132MB of SDRAM.

Flash Memory The flash memory option is useful for storing information such as downloaded fonts, macros, symbol sets, logos, and forms. Use your printer driver or the MarkVision utility to download resources to flash memory.

You can install one flash memory option in your printer. Flash memory options available are 2, 4, 8, and 16MB.

See page 212 for instructions on installing the hard disk option, which provides memory storage similar to the flash memory option.

206 Chapter 11: Memory and Option Cards

Page 219 of the Lexmark M412 user manual — 207 Installing Memory Options
Page 219 · click to enlarge
Page 219

Installing Memory Options

This section offers instructions for installing either a printer memory option or a flash memory option card. You may install any one of the following memory configu- rations on your printer system board:

  • One printer memory option.
  • One flash memory option.
  • One printer memory option and one flash memory option.
  • Two printer memory options.

Before installing any option card, you must remove the printer system board cover.

1 Follow the steps in “Accessing the Printer System Board” on page 201.

2 Locate the two memory connectors on the system board.

Both memory connector 1 and memory connector 2 are capable of accepting either a printer memory option or a flash memory option card.

3 Follow the steps under “Removing Memory Options” on page 210 if you need to remove an option card before you install a new one. Otherwise, go to step 4.

207 Installing Memory Options

Memory Connector 1 · Memory Connector 2

Page 220 of the Lexmark M412 user manual — 208 Chapter 11: Memory and Option Cards
Page 220 · click to enlarge
Page 220

4 Unpack the new option card.

Avoid touching the connection points along the edge of the card. Save the packaging.

5 Hold the option card with the connection points pointing toward the system board as shown.

208 Chapter 11: Memory and Option Cards

Connection Points · Connection Points

Page 221 of the Lexmark M412 user manual — 209 Installing Memory Options
Page 221 · click to enlarge
Page 221

6 Insert the option card straight into the connector as shown.

Lexmark M412 — Installing MemoryOptions diagram (page 221)
Fig. 76 · Installing MemoryOptions

Make sure the edges of the card fit into the slots located on each of the connector latches.

7 Push in on one side of the card and push in one of the latches until it snaps into place. Repeat for the other side of the card.

Lexmark M412 — Installing MemoryOptions diagram (page 221)
Fig. 77 · Installing MemoryOptions

Make sure each latch fits over the notch located on either side of the option card.

8 Repeat steps 4 through 7 to install another mem- ory option card in one of the memory connectors. Otherwise, go to step 9.

9 Continue with “Installing an Option Card” on page 216 if you have other option cards to install. Otherwise, go to “Closing the Printer System Board” on page 220.

209 Installing Memory Options

Latch

Page 222 of the Lexmark M412 user manual — 210 Chapter 11: Memory and Option Cards
Page 222 · click to enlarge
Page 222

Removing Memory Options

Before removing a memory option, follow the steps under “Accessing the Printer System Board” on page 201.

To remove a printer memory option or a flash memory option card:

1 Locate the option card that you want to remove.

2 Push the latches at each end of the memory con- nector away from the option card.

3 Pull the option card straight out of the memory connector.

4 Place the option card in its original packaging.

If you did not save the packaging, wrap the option card in paper and store it in a box.

5 Follow the steps under “Installing Memory Options” on page 207 if you need to install a new printer memory option or flash memory option card. Otherwise, go to step 6.

6 Continue with “Closing the Printer System Board” on page 220.

210 Chapter 11: Memory and Option Cards

Page 223 of the Lexmark M412 user manual — 211 Understanding Option Cards
Page 223 · click to enlarge
Page 223

Understanding

Four kinds of option cards are available for your printer:

Option Cards

  • Internal print server option card
  • Tri-Port interface option card
  • Hard disk option
  • Parallel/USB interface option card

Refer to the documentation that is included with each option card for detailed information about that specific card.

The installation instructions are the same for each type of option card; therefore, they are grouped together. Installa- tion instructions begin on page 216.

Internal Print Server

An optional internal print server lets you connect your printer to a local area network (LAN). You can install one print server in your printer. There are MarkNetTM cards available to support the following topologies:

(Internal Network

Adapter or INA)

  • Ethernet (100BaseTX, 10BaseT, 10Base2)
Lexmark M412 — (Internal Network diagram (page 223)
Fig. 78 · (Internal Network
  • Token-Ring (DB9 or RJ45)

Internal print servers have a similar size and shape. Make sure the network port on the card corresponds to your net- work cable requirements. Refer to the documentation that came with the print server for more information.

Installing the Optional Internal Print Server

To install, complete the following two sections in order:

  • “Accessing the Printer System Board” on page 201
  • “Installing an Option Card” on page 216

211 Understanding Option Cards

Card Connector Points

Page 224 of the Lexmark M412 user manual — 212 Chapter 11: Memory and Option Cards
Page 224 · click to enlarge
Page 224

Tri-Port Interface

The Tri-Port interface option card lets you connect to:

Option Card

  • A LocalTalk network
  • Serial interface (RS-232C or Serial RS-422A)
  • An infrared adapter
Lexmark M412 — Option Card diagram (page 224)
Fig. 79 · Option Card

For information about the LocalTalk network, see “Local- Talk Menu” on page 96.

For more information about serial interface, see “Serial Menu” on page 87.

An infrared adapter receives an infrared beam that allows you to print remotely to an IrDA-compatible computer. For more information, see “Infrared Menu” on page 93.

Installing the Tri-Port Interface Option Card

To install, complete the following two sections in order:

  • “Accessing the Printer System Board” on page 201
  • “Installing an Option Card” on page 216

Hard Disk Option Like the flash memory option, the hard disk option is use- ful for storing information such as downloaded fonts, macros, and symbol sets.

You can also use the hard disk option to store incoming print jobs in a buffer until they print. Since hard disk memory provides permanent storage, job buffering to the hard disk prevents the loss of print job data if the printer loses power. It may also free your application faster for other work. Job buffering is only available for jobs trans- mitted across the standard parallel and USB interface.

212 Chapter 11: Memory and Option Cards

Show 4 more labels / short text on this page
LocalTalk Port · Serial Port · Infrared Port · Card Connector Points
Page 225 of the Lexmark M412 user manual — 213 Understanding Option Cards
Page 225 · click to enlarge
Page 225

You can purchase:

  • A hard disk with an adapter card already installed.
  • A hard disk that supports Optra Forms TM with an adapter card already installed. Refer to Optra Forms for more information.
  • A hard disk adapter card for installing a separately purchased hard disk.

Complete the following instructions to attach the hard disk to the adapter card. If your disk is already attached to a card, go to “Accessing the Printer System Board” on page 201.

Attaching a Hard Disk to the Adapter Card

You can use the adapter card with any hard disk meeting the following criteria:

  • 2.5-inch platter
  • ATA-2 (IDE) interface
  • Maximum thickness of 15 mm (.59 in.)

To attach the hard disk to the adapter card:

Lexmark M412 — Attaching a Hard Disk to the Adapter Card diagram (page 225)
Fig. 80 · Attaching a Hard Disk to the Adapter Card

1 Align the connector pins on the end of the hard disk with the connector on the back of the adapter card. Hard Disk

213 Understanding Option Cards

Page 226 of the Lexmark M412 user manual — 214 Chapter 11: Memory and Option Cards
Page 226 · click to enlarge
Page 226

2 Push the hard disk securely into the connector.

Lexmark M412 — Installing the Hard Disk Option Card diagram (page 226)
Fig. 81 · Installing the Hard Disk Option Card

3 Turn the adapter card over and insert the four screws. Securely tighten each screw.

Lexmark M412 — Installing the Hard Disk Option Card diagram (page 226)
Fig. 82 · Installing the Hard Disk Option Card

Installing the Hard Disk Option Card

To install, complete the following two sections in order:

  • “Accessing the Printer System Board” on page 201
  • “Installing an Option Card” on page 216

214 Chapter 11: Memory and Option Cards

Page 227 of the Lexmark M412 user manual — 215 Understanding Option Cards
Page 227 · click to enlarge
Page 227

Parallel/USB

The parallel/USB interface option card lets you connect your printer to a parallel interface. You can also use the USB (Universal Serial Bus) port to connect your printer to a computer. For more information about USB, see “USB Menu” on page 99.

Interface Option Card

Installing the Parallel/USB Interface Option Card

Lexmark M412 — Installing the Parallel/USB Interface Option Card diagram (page 227)
Fig. 83 · Installing the Parallel/USB Interface Option Card

To install, complete the following two sections in order:

  • “Accessing the Printer System Board” on page 201
  • “Installing an Option Card” on page 216

215 Understanding Option Cards

USB Port · Parallel Port · Card Connector Points

Page 228 of the Lexmark M412 user manual — 216 Chapter 11: Memory and Option Cards
Page 228 · click to enlarge
Page 228

Installing an

Before installing an option card, follow the steps under “Accessing the Printer System Board” on page 201.

Option Card

Lexmark M412 — Option Card diagram (page 228)
Fig. 84 · Option Card

To install a hard disk option card, optional internal print server, Tri-Port interface option card, or parallel/USB interface option card:

1 Locate the option card connector on the printer system board.

2 Follow the steps under “Removing an Option Card” on page 219 if you need to remove an option card before installing another one. Otherwise, go to step 3.

216 Chapter 11: Memory and Option Cards

Page 229 of the Lexmark M412 user manual — 217 Installing an Option Card
Page 229 · click to enlarge
Page 229
Lexmark M412 — Installing an OptionCard diagram (page 229)
Fig. 85 · Installing an OptionCard

3 Remove the metal plate covering the connector slot.

a Locate the two screws on the back of the printer

that attach the metal plate to the slot.

b Remove and save the two screws. Remove and

discard the plate.

4 Unpack the option card.

Save the packing materials.

5 Align the connector on the option card with the connector on the system board.

The cable connectors on the side of the option card must fit through the opening in the faceplate.

6 Push the option card firmly into the option card connector on the system board.

217 Installing an Option Card

Option Card Connector

Page 230 of the Lexmark M412 user manual — 218 Chapter 11: Memory and Option Cards
Page 230 · click to enlarge
Page 230
Lexmark M412 — Installing an OptionCard diagram (page 230)
Fig. 86 · Installing an OptionCard

7 Insert the two screws saved from the metal plate (or the extra screws shipped with the option card) into the holes on either side of the connector slot.

8 Gently tighten the screws to secure the card to the system board.

9 Continue with “Closing the Printer System Board” on page 220.

218 Chapter 11: Memory and Option Cards

Page 231 of the Lexmark M412 user manual — 219 Removing an Option Card
Page 231 · click to enlarge
Page 231

Removing an

Before removing an option card, follow the steps under “Accessing the Printer System Board” on page 201.

Option Card

To remove an option card:

1 Remove the two screws on either side of the con- nector slot located on the back of the printer.

2 Pull the option card straight out of the system board connector.

3 Place the option card in its original packaging.

If you did not save the packaging, wrap the card in paper and store it in a box.

4 Follow the steps under “Installing an Option Card” on page 216 if you need to install an option card. Otherwise, go to step 5.

5 Continue with “Closing the Printer System Board” on page 220.

219 Removing an Option Card

Page 232 of the Lexmark M412 user manual — 220 Chapter 11: Memory and Option Cards
Page 232 · click to enlarge
Page 232

Closing the Printer

After you have installed all of your options on the printer system board, reattach the shield and close the side door:

System Board

1 Grasp the shield by the tabs and align the three keyholes on the shield with the top three screws on the side of the printer.

2 Holding the shield by the tabs, slide it down.

3 Tighten all six screws.

220 Chapter 11: Memory and Option Cards

Tabs

Page 233 of the Lexmark M412 user manual — 221 Closing the Printer System Board
Page 233 · click to enlarge
Page 233

4 Hold the side door slightly to the left of the printer and place the latches located on the back edge of the side door against the metal shield.

Lexmark M412 — Closing the Printer System Board diagram (page 233)
Fig. 87 · Closing the Printer System Board

The edge of the metal shield fits into the latches. The top latch fits inside the back of the printer.

5 Close the side door, pressing on the side door latches to snap it into place.

7 Reconnect all cables to the back of the printer.

8 Reconnect the printer power cord to the printer and a properly grounded electrical outlet.

10 Make sure the Ready message appears on the oper- ator panel display.

If an error message appears, see “Understanding Printer Messages” on page 151.

221 Closing the Printer System Board

Page 234 of the Lexmark M412 user manual — 222 Chapter 11: Memory and Option Cards
Page 234 · click to enlarge
Page 234

222 Chapter 11: Memory and Option Cards

Page 235 of the Lexmark M412 user manual — 223 Installing the Optional Drawer
Page 235 · click to enlarge
Page 235

Optional 500-Sheet Drawer

Decide on a location to set the support unit. The printer will be placed on top of it, so allow enough space for easy paper access. The location must be sturdy and large enough to accommodate the printer and the optional 500-sheet drawer.

Installing the Optional Drawer

The optional drawer consists of a support unit and an input tray. To install the optional 500-sheet drawer:

1 Turn the printer power Off (O).

2 Unplug the printer power cord.

3 Disconnect all cables from the back of the printer.

4 Remove the support unit from its packaging.

Remove any packing tape.

223 Installing the Optional Drawer

Page 236 of the Lexmark M412 user manual — 224 Chapter 12: Optional 500-Sheet Drawer
Page 236 · click to enlarge
Page 236

5 Pull the input tray out of the support unit.

Lexmark M412 — Optional 500-Sheet Drawer diagram (page 236)
Fig. 88 · Optional 500-Sheet Drawer

Remove any packing material and tape from the input tray.

6 Grasp the support unit on each side at opposite corners and move it to the location being used.

Lexmark M412 — Optional 500-Sheet Drawer diagram (page 236)
Fig. 89 · Optional 500-Sheet Drawer

7 Notice the following parts located on the top sur- face of the optional support unit: the tab, the round hole, and the four square holes.

Lexmark M412 — Optional 500-Sheet Drawer diagram (page 236)
Fig. 90 · Optional 500-Sheet Drawer

8 Lift the printer by the handholds or ask someone to help you lift the printer.

The bottom surface of the printer has matching holes or feet that accommodate the tab, round hole, and four square holes.

Round Hole Square Holes

224 Chapter 12: Optional 500-Sheet Drawer

Square Holes

Page 237 of the Lexmark M412 user manual — 225 Installing the Optional Drawer
Page 237 · click to enlarge
Page 237

9 Place the printer on top of the support unit.

Lexmark M412 — Optional 500-Sheet Drawer diagram (page 237)
Fig. 91 · Optional 500-Sheet Drawer

Make sure the edges of the printer and the support unit are aligned properly.

10 Load print material in the input tray.

See “Loading Print Material” on page 124 for more information.

11 Install the input tray in the support unit.

12 Reconnect all cables to the back of the printer.

13 Plug the printer power cord into a properly grounded electrical outlet.

14 Turn the printer power On (|).

15 When Ready displays, press Menu> to enter the menus.

16 Set the PAPER SIZE , PAPER TYPE , and PAPER

LENGTH menu settings for this paper source.

See PAPER SIZE on page 45, PAPER TYPE on page 47, and PAPER LENGTH on page 52 for more informa- tion.

17 Press Go to return to the Ready state.

If an error message appears, see “Understanding Printer Messages” on page 151.

225 Installing the Optional Drawer

Page 238 of the Lexmark M412 user manual — 226 Chapter 12: Optional 500-Sheet Drawer
Page 238 · click to enlarge
Page 238

226 Chapter 12: Optional 500-Sheet Drawer

Page 239 of the Lexmark M412 user manual — 227 Connecting the Cable and Using the Infrared Adapter
Page 239 · click to enlarge
Page 239

13 Infrared Adapter

You can use an infrared adapter to print remotely to an IrDA-compatible computer equipped with an infrared port.

The Tri-Port interface option card, which includes an infrared port, lets you connect the infrared adapter to your printer. For more information, see “Tri-Port Interface Option Card” on page 212. If you need to install the Tri- Port interface option card, see “Installing an Option Card” on page 216.

After you install the Tri-Port interface option card, com- plete the following steps to connect the infrared adapter to your printer.

Connecting the Cable and Using

To connect the infrared adapter to your printer:

1 Unplug the printer power cord.

the Infrared

2 Locate the infrared port on the back of your printer.

Adapter

The infrared port is attached to the Tri-Port interface option card installed in your printer.

227 Connecting the Cable and Using the Infrared Adapter

Page 240 of the Lexmark M412 user manual — 228 Chapter 13: Infrared Adapter
Page 240 · click to enlarge
Page 240
Lexmark M412 — Infrared Adapter diagram (page 240)
Fig. 92 · Infrared Adapter

3 Plug the adapter cable into the infrared port.

4 Reconnect the printer power cord to a properly grounded electrical outlet.

If any light on the infrared adapter comes on when the printer is plugged in, the adapter is connected to the port correctly.

5 Aim the computer infrared port at the infrared port on the front of the Tri-Port interface option card.

Refer to the documentation that came with your computer for information about your computer infrared port.

6 Draw an imaginary line between the two infrared ports. Aim the infrared port on your computer within 15 degrees of either side of this line, as shown.

Lexmark M412 — Infrared Adapter diagram (page 240)
Fig. 93 · Infrared Adapter

7 Send a job to print.

If the job does not print correctly, see Infrared Adapter on page 181.

228 Chapter 13: Infrared Adapter

Infrared Port

Page 241 of the Lexmark M412 user manual — Settings Page
Page 241 · click to enlarge
Page 241

Verifying the Installation of

Options

You can verify that printer options are properly installed by printing a menu settings page.

A menu settings page lists:

  • All printer settings in the operator panel menus and their default values.
  • All installed features and options, such as the optional 500-sheet drawer, internal print server (also called an internal network adapter or INA), flash memory option, printer memory option, and hard disk option.
  • Amount of available printer memory.
  • Other printer settings.

Printing the Menu

Before printing the menu settings page, make sure the selected paper source holds letter-, legal-, or A4-size paper, the PAPER SIZE setting is set to the correct size, and the PAPER TYPE setting for the paper source is Plain Paper.

Settings Page

229 Printing the Menu Settings Page

Page 242 of the Lexmark M412 user manual — 230 Chapter 14: Verifying the Installation of Options
Page 242 · click to enlarge
Page 242

To print a menu settings page:

1 Make sure the printer power is On (|) and the

Ready status message appears on the display.

If you need help, see “Using the Operator Panel” on page 34 to identify the display and operator panel buttons.

2 Press Menu> or <Menu to enter the menus.

3 Continue to press and release Menu> or <Menu until you see UTILITIES MENU.

4 Press Select.

5 Press Menu> until Print Menus appears on the sec- ond line of the display.

6 Press Select.

The message Printing Menu Settings appears and remains on the operator panel display until the page prints. The printer returns to the Ready state after the menu settings page prints.

If an error message appears, see “Understanding Printer Messages” on page 151.

7 Check to see if the option you installed is listed.

All installed options are listed on the menu settings page under Installed Features.

If an installed option does not appear on the page, it is not installed correctly or aligned properly. Turn the printer power Off (O), unplug the printer power cord, reinstall the option, and print the menu set- tings page again.

230 Chapter 14: Verifying the Installation of Options

Page 243 of the Lexmark M412 user manual — 231 Appendix A: Understanding Fonts
Page 243 · click to enlarge
Page 243

Understanding

A

Fonts

This appendix contains basic information about fonts, their characteristics, and the specific fonts available in PCL 6 and PostScript 3 emulations.

Typefaces

A font is a set of characters and symbols created with a dis- tinct design. The distinct design is called a typeface. The typefaces you select add personality to a document. Well-chosen typefaces make a document easier to read.

and Fonts

The printer has numerous resident fonts in PCL 6 and PostScript 3 emulations. See “Resident Fonts” on page 235 for a listing of all resident fonts.

Weight and Style Typefaces are often available in different weights and styles. These variations modify the original typeface so you can, for example, emphasize important words in text or highlight book titles. The different weights and styles are designed to complement the original typeface.

Weight refers to the thickness of the lines that form the characters. Thicker lines result in darker characters. Some words commonly used to describe the weight of a type- face are bold, medium, light, black and heavy.

231 Appendix A: Understanding Fonts

Page 244 of the Lexmark M412 user manual — 232 Appendix A: Understanding Fonts
Page 244 · click to enlarge
Page 244

Style refers to other typeface modifications, such as tilt or character width. Italic and oblique are styles where the characters are tilted. Narrow, condensed and extended are three common styles that modify the character widths.

Some fonts combine several weight and style modifica- tions; for example, Helvetica Narrow Bold Italic. A group of several weight and style variations of a single typeface is called a typeface family. Most typeface families have four variations: regular, italic, bold, and bold italic. Some fami- lies have more variations, as the following illustration for the Helvetica typeface family shows:

Lexmark M412 — Pitch and Point Size diagram (page 244)
Fig. 94 · Pitch and Point Size

Pitch and Point Size The size of a font is specified as either a pitch or point size, depending on whether the font is fixed space or propor- tional.

In fixed space fonts, each character has the same width. Pitch is used to specify the size of fixed space fonts. It is a measure of the number of characters that will print in one horizontal inch of type. For example, all 10-pitch fonts print 10 characters per inch (cpi) and all 12-pitch fonts print 12 cpi:

Lexmark M412 — Pitch and Point Size diagram (page 244)
Fig. 95 · Pitch and Point Size

232 Appendix A: Understanding Fonts

Page 245 of the Lexmark M412 user manual — ITC Avant Garde abcdefghABCDEFGH
Page 245 · click to enlarge
Page 245

In proportional (or typographic) fonts, every character can have a different width. Since proportional fonts have char- acters with different widths, the font size is specified in point size, not pitch. Point size refers to the height of the characters in the font. A point is defined as 1/72 inch. The characters in a font printed at 24 point will be twice as large as the characters in the same font printed at 12 point. The following illustration shows samples of a font printed in different point sizes:

48 point 36 point

24 point 18 point 12 point 10 point

The point size of a font is defined as the distance from the top of the tallest character in the font to the bottom of the lowest character in the font. Due to the definition of point size, different fonts printed at the same point size may appear quite different in size. This is because there are other font parameters that affect how the font looks. How- ever, the point size of a font is an excellent specification of the relative size of a font. The following examples illus- trate two very different proportional fonts at 14 point:

ITC Avant Garde abcdefghABCDEFGH

ITC Zapf Chancery abcdefghABCDEFGH

233 Appendix A: Understanding Fonts

Page 246 of the Lexmark M412 user manual — 234 Appendix A: Understanding Fonts
Page 246 · click to enlarge
Page 246

Bitmapped and

The printer uses both bitmapped and scalable fonts.

Scalable Fonts

Bitmapped fonts are stored in printer memory as pre- defined patterns of bits that represent a typeface at a spe- cific size, style and resolution. An example of a character from a bitmapped font is shown at left.

Bitmapped fonts are available in different type styles and point sizes as downloadable fonts. Contact your point of purchase for more information about downloadable fonts.

Scalable fonts are stored as computer programs that define the outlines of the characters in the font. Each time you print characters from a scalable font, the printer creates a bitmap of the characters at the point size you choose and saves it temporarily in printer memory. These temporary bitmapped fonts are deleted when you turn off or reset the printer. Scalable fonts provide the flexibility of printing in many different point sizes.

Your printer uses different scalable font formats for down- loading fonts to the printer. PCL 6 emulation uses Intelli- font and TrueType scalable fonts. PostScript 3 emulation uses Type 1 and TrueType scalable fonts. There are thou- sands of different scalable fonts available in these different font formats from numerous font suppliers.

If you plan to use many downloadable bitmapped or scal- able fonts or if you plan to use many different sizes of scal- able fonts, you may need to purchase additional memory for your printer. See page 206 for more information.

234 Appendix A: Understanding Fonts

Page 247 of the Lexmark M412 user manual — 235 Appendix A: Understanding Fonts
Page 247 · click to enlarge
Page 247

Resident Fonts Your printer is equipped with resident fonts stored perma- nently in printer memory. Different fonts are available in PCL 6 and PostScript 3 emulations. Some of the most pop- ular typefaces, like Courier and Times New Roman, are available for all printer languages.

The following tables list all the fonts resident in your printer. See page 242 for instructions on how to print sam- ples of the fonts. You can select the resident fonts from your software application, or from the operator panel if you are using PCL 6 emulation.

Resident Scalable Fonts

PCL 6 Emulation PostScript 3 Emulation

Antique Olive Italic AntiqueOlive-Italic

Antique Olive Bold AntiqueOlive-Bold

Arial Bold Italic Arial-BoldItalicMT

ITC Avant Garde Book AvantGarde-Book

ITC Avant Garde Book Oblique AvantGarde-BookOblique

ITC Avant Garde Demi AvantGarde-Demi

ITC Avant Garde Demi Oblique AvantGarde-DemiOblique

ITC Bookman Light Bookman-Light

ITC Bookman Light Italic Bookman-LightItalic

ITC Bookman Demi Bookman-Demi

ITC Bookman Demi Italic Bookman-DemiItalic

235 Appendix A: Understanding Fonts

Show 10 more labels / short text on this page
Albertus Medium AlbertusMT · AlbertusMT-Italic · AlbertusMT-Light · Albertus Extra Bold · Antique Olive AntiqueOlive-Roman · AntiqueOlive-Compact · Arial ArialMT · Arial Italic Arial-ItalicMT · Arial Bold Arial-BoldMT · Clarendon Condensed Bold
Page 248 of the Lexmark M412 user manual — 236 Appendix A: Understanding Fonts
Page 248 · click to enlarge
Page 248

Resident Scalable Fonts (continued)

PCL 6 Emulation PostScript 3 Emulation

CourierPS Bold Italic Courier-BoldOblique

CG Omega Bold Italic

Garamond Kursiv Halbfett Garamond-KursivHalbfett

Helvetica Light Oblique Helvetica-LightOblique

Helvetica Black Oblique Helvetica-BlackOblique

Helvetica Bold Italic Helvetica-BoldOblique

Helvetica Narrow Italic Helvetica-Narrow-Oblique

Helvetica Narrow Bold Helvetica-Narrow-Bold

Helvetica Narrow Bold Italic Helvetica-Narrow-BoldOblique

CG Times Italic Intl-CG-Times-Italic

CG Times Bold Intl-CG-Times-Bold

CG Times Bold Italic Intl-CG-Times-BoldItalic

236 Appendix A: Understanding Fonts

Show 17 more labels / short text on this page
Coronet Coronet-Regular · CourierPS Courier · CourierPS Oblique Courier-Oblique · CourierPS Bold Courier-Bold · CG Omega · CG Omega Bold · CG Omega Italic · Garamond Antiqua Garamond-Antiqua · Garamond Halbfett Garamond-Halbfett · Garamond Kursiv Garamond-Kursiv · Helvetica Light Helvetica-Light · Helvetica Black Helvetica-Black · Helvetica Helvetica · Helvetica Italic Helvetica-Oblique · Helvetica Bold Helvetica-Bold · Helvetica Narrow Helvetica-Narrow · CG Times Intl-CG-Times
Page 249 of the Lexmark M412 user manual — 237 Appendix A: Understanding Fonts
Page 249 · click to enlarge
Page 249

Resident Scalable Fonts (continued)

PCL 6 Emulation PostScript 3 Emulation

Univers Medium Italic Intl-Univers-MediumItalic

Univers Bold Italic Intl-Univers-BoldItalic

Courier Bold Italic Intl-Courier-BoldOblique

Letter Gothic Italic LetterGothic-Slanted

Letter Gothic Bold LetterGothic-Bold

Century Schoolbook Roman NewCenturySchlbk-Roman

Century Schoolbook Italic NewCenturySchlbk-Italic

Century Schoolbook Bold NewCenturySchlbk-Bold

Century Schoolbook Bold Italic NewCenturySchlbk-BoldItalic

Palatino Bold Italic Palatino-BoldItalic

237 Appendix A: Understanding Fonts

Show 19 more labels / short text on this page
Univers Medium Intl-Univers-Medium · Univers Bold Intl-Univers-Bold · Courier Intl-Courier · Courier Italic Intl-Courier-Oblique · Courier Bold Intl-Courier-Bold · Letter Gothic LetterGothic · LetterGothic-BoldSlanted · Marigold Marigold · Optima · Optima-Bold · Optima-BoldItalic · Optima-Italic · Palatino Roman Palatino-Roman · Palatino Italic Palatino-Italic · Palatino Bold Palatino-Bold · SymbolPS Symbol · Symbol · Times Roman Times-Roman · Times Italic Times-Italic
Page 250 of the Lexmark M412 user manual — 238 Appendix A: Understanding Fonts
Page 250 · click to enlarge
Page 250

Resident Scalable Fonts (continued)

PCL 6 Emulation PostScript 3 Emulation

Times Bold Italic Times-BoldItalic

Times New Roman TimesNewRomanPSMT

Times New Roman Italic TimesNewRomanPS-ItalicMT

Times New Roman Bold TimesNewRomanPS-BoldMT

Times New Roman Bold Italic TimesNewRomanPS-BoldItalicMT

Univers Condensed Medium Univers-Condensed

Univers Condensed Medium Italic Univers-CondensedOblique

Univers Condensed Bold Univers-CondensedBold

Univers Condensed Bold Italic Univers-CondensedBoldOblique

ITC Zapf Chancery Medium Italic ZapfChancery-MediumItalic

ITC Zapf Dingbats ZapfDingbats

Resident Bitmapped Fonts

PCL 6 Emulation PostScript 3 Emulation

238 Appendix A: Understanding Fonts

Show 8 more labels / short text on this page
Times Bold Times-Bold · Univers · Univers-Oblique · Univers-Bold · Univers-BoldOblique · Wingdings Wingdings-Regular · Line Printer 16 · POSTNET Barcode
Page 251 of the Lexmark M412 user manual — 239 Appendix A: Understanding Fonts
Page 251 · click to enlarge
Page 251

Symbol Sets A symbol set is the collection of alphabetic and numeric characters, punctuation, and special characters available in the font you select. Symbol sets support the require- ments for different languages or specific applications, such as math symbols used for scientific text.

In PCL 6 emulation, a symbol set also defines which char- acter will print for each key on the keyboard (or more spe- cifically, for each code point). Some applications require different characters at some code points. To support multi- ple applications and languages, your printer has 83 symbol sets for the resident PCL 6 emulation fonts.

Symbol Sets for PCL 6 Emulation

Not all font names support all of the symbol sets listed. Refer to the Technical Reference to determine which sym- bols sets are supported by each font name.

ABICOMP Brazil/Portugal ABICOMP International DeskTop Legal MC Text Microsoft Publishing Russian-GOST Ukrainian PCL ITC Zapf Dingbats PS ITC Zapf Dingbats PS Math PS Text Pi Font Symbol Wingdings POSTNET Barcode ISO : German ISO : Spanish ISO 2: IRV (Int'l Ref Version) ISO 4: United Kingdom ISO 6: ASCII ISO 10: Swedish ISO 11: Swedish for Names ISO 14: JIS ASCII ISO 15: Italian ISO 16: Portuguese ISO 17: Spanish ISO 21: German ISO 25: French ISO 57: Chinese ISO 60: Norwegian version 1 ISO 61: Norwegian version 2

239 Appendix A: Understanding Fonts

Page 252 of the Lexmark M412 user manual — 240 Appendix A: Understanding Fonts
Page 252 · click to enlarge
Page 252

ISO 69: French ISO 84: Portuguese ISO 85: Spanish ISO 8859-1 Latin 1 (ECMA-94) ISO 8859-2 Latin 2 ISO 8859-5 Latin/Cyrillic ISO 8859-7 Latin/Greek ISO 8859-9 Latin 5 ISO 8859-10 Latin 6 ISO 8859-15 Latin 9 PC-8 Bulgarian PC-8 Danish/Norwegian (437N) PC-8 Greek Alternate (437G) PC-8 Turkish (437T) PC-8 Latin/Greek PC-8 PC Nova PC-8 Polish Mazovia PC-8 Code Page 437 PC-775 Baltic (PC-8 Latin 6) PC-850 Multilingual PC-851 Greece PC-852 Latin 2 PC-853 Latin 3 (Turkish) PC-855 Cyrillic PC-857 Latin 5 (Turkish) PC-858 Multilingual Euro PC-860 Portugal PC-861 Iceland PC-863 Canadian French PC-865 Nordic PC-866 Cyrillic PC-869 Greece PC-911 Katakana PC-1004 OS/2 Math-8 Greek-8 Turkish-8 Roman-8 Roman-9 Roman Extension Ventura ITC Zapf Dingbats Ventura International Ventura Math Ventura US Windows 3.0 Latin 1 Windows 98 Cyrillic Windows 98 Greek Windows 98 Latin 1 Windows 98 Latin 2 Windows 98 Latin 5 Windows 98 Latin 6 (Baltic)

240 Appendix A: Understanding Fonts

Page 253 of the Lexmark M412 user manual — 241 Appendix A: Understanding Fonts
Page 253 · click to enlarge
Page 253

Downloadable

You can download scalable fonts in PostScript 3 emulation and either scalable or bitmapped fonts in PCL 6 emula- tion. Fonts can be downloaded to printer memory or to a flash memory option or hard disk option. Fonts down- loaded to flash memory or hard disk remain in memory even after the printer language changes, the printer resets, or the printer is turned off.

Fonts

The MarkVision utility includes a remote management function that lets you manipulate the font files you have downloaded to flash memory or hard disk. See page 25 for more information about MarkVision.

241 Appendix A: Understanding Fonts

Page 254 of the Lexmark M412 user manual — 242 Appendix A: Understanding Fonts
Page 254 · click to enlarge
Page 254

Printing a Font

To print samples of all the fonts currently available for your printer:

Sample List

1 Make sure the printer power is On (|) and the

Ready status message appears on the display.

2 Press Menu> or <Menu to enter the menus.

3 Continue to press and release Menu> until you see

UTILITIES MENU.

4 Press Select.

5 Press Menu> until Print Fonts appears.

6 Press Select.

7 Press Menu> or <Menu until either PCL Fonts or

PS Fonts appears on the second line of the display.

– Select PCL Fonts to print a listing of the fonts available to the PCL emulator. – Select PS Fonts to print a listing of the fonts avail- able to the PostScript 3 emulator.

8 Press Select.

The message Printing Font List appears and remains on the operator panel display until the page prints. The printer returns to the Ready state after the font sample list prints.

242 Appendix A: Understanding Fonts

Page 255 of the Lexmark M412 user manual — 243 Appendix B: Notices
Page 255 · click to enlarge
Page 255

B Notices

Electronic Emissions

Notices

Electronic emission information for your printer varies, depending on whether or not you have an optional network adapter installed.

Without a Network

Federal Communications Commission (FCC) Compliance Information Statement

Adapter Installed

The Lexmark Optra M410 and M412 laser printers, Type 4045, have been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The FCC Class B limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter- mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult your point of purchase or service representative for additional suggestions.

The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate this equipment.

243 Appendix B: Notices

Page 256 of the Lexmark M412 user manual — 244 Appendix B: Notices
Page 256 · click to enlarge
Page 256

To assure compliance with FCC regulations on electromagnetic interference for a Class B computing device, use a properly shielded and grounded cable such as Lexmark part number 1329605 for parallel and 12A2405 for USB. Use of a substitute cable not prop- erly shielded and grounded may result in a violation of FCC regulations.

Any questions regarding this compliance information statement should be directed to:

Director of Lab Operations Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (606) 232-3000

Industry Canada Compliance Statement

This Class B digital apparatus meets all requirements of the Canadian Interference- Causing Equipment Regulations.

Avis de conformité aux normes d’Industrie Canada

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

European Community (EC) Directives Conformity

This product is in conformity with the protection requirements of EC Council directives 89/336/EEC and 73/23/EEC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits.

A declaration of conformity with the requirements of the Directive has been signed by the Director of Manufacturing and Technical Support, Lexmark International, S.A., Boi- gny, France.

This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.

244 Appendix B: Notices

Page 257 of the Lexmark M412 user manual — 245 Appendix B: Notices
Page 257 · click to enlarge
Page 257

With a Network Adapter

Federal Communications Commission (FCC) Compliance Information Statement

Installed

The Lexmark Optra M410n and M412n laser printers, Type 4045, have been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The FCC Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equip- ment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interfer- ence at his own expense.

The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate this equipment.

Industry Canada Compliance Statement

This Class A digital apparatus meets all requirements of the Canadian Interference- Causing Equipment Regulations.

Avis de conformité aux normes d’Industrie Canada

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

European Community (EC) Directives Conformity

This product is in conformity with the protection requirements of EC Council directives 89/336/EEC and 73/23/EEC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits.

A declaration of conformity with the requirements of the Directive has been signed by the Director of Manufacturing and Technical Support, Lexmark International, S.A., Boi- gny, France.

This product satisfies the Class A limits of EN 55022 and safety requirements of EN 60950.

245 Appendix B: Notices

Page 258 of the Lexmark M412 user manual — 246 Appendix B: Notices
Page 258 · click to enlarge
Page 258

The United Kingdom Telecommunications Act

This apparatus is approved under the approval number NS/G/1234/J/100003 for the indirect connections to the public telecommunications systems in the United Kingdom.

German Acoustics

The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.

Statement

1-Meter Average Sound Pressure, dBA Optra M410 Optra M412

Printing 48 dBA 50 dBA

Idling 30 dBA 30 dBA

Energy Star The EPA ENERGY STAR Computers program is a partnership effort with computer manufacturers to promote the introduction of energy-efficient products and to reduce air pollution caused by power generation.

Companies participating in this program introduce personal computers, printers, moni- tors, or fax machines that power down when they are not being used. This feature will cut the energy used by up to 50 percent. Lexmark is proud to be a participant in this program.

As an Energy Star Partner, Lexmark International, Inc. has determined that this product meets the Energy Star guidelines for energy efficiency.

246 Appendix B: Notices

Acoustics

Page 259 of the Lexmark M412 user manual — 247 Appendix B: Notices
Page 259 · click to enlarge
Page 259

Laser Notices The following laser notice labels may be affixed to this printer as shown:

Laser Advisory Label

Lexmark M412 — Laser Advisory Label diagram (page 259)
Fig. 96 · Laser Advisory Label

247 Appendix B: Notices

Page 260 of the Lexmark M412 user manual — 248 Appendix B: Notices
Page 260 · click to enlarge
Page 260

Class 1 Laser Statement Label

CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE

APPAREIL À LASER DE CLASSE 1

TO IEC 825

Laser Notice The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1.

Class I laser products are not considered to be hazardous. The printer contains inter- nally a Class IIIb (3b) laser that is nominally a 5 milliwatt aluminum gallium arsenide laser operating in the wavelength region of 770-795 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.

Laser Der Drucker erfüllt gemäß amtlicher Bestätigung der USA die Anforderungen der Bestimmung DHHS (Department of Health and Human Services) 21 CFR Teil J für Laserprodukte der Klasse I (1). In anderen Ländern gilt der Drucker als Laserprodukt der Klasse I, der die Anforderungen der IEC (International Electrotechnical Commission) 60825-1 gemäß amtlicher Bestätigung erfüllt.

Laserprodukte der Klasse I gelten als unschädlich. Der Drucker ist intern mit einem Laser der Klasse IIIb (3b) ausgestattet. Hierbei handelt es sich nominell um einen 5- Milliwatt-Aluminium-Galliumarsenidlaser, der in einem Wellenlängenbereich von 770 bis 795 Nanometern arbeitet. Das Lasersystem und der Drucker sind so konzipiert, daß im Normalbetrieb, bei der Wartung durch den Benutzer oder bei ordnungsgemäßer Wartung durch den Kundendienst Laserbestrahlung, die die Klasse I übersteigen würde, Menschen keinesfalls erreicht.

248 Appendix B: Notices

Page 261 of the Lexmark M412 user manual — 249 Appendix B: Notices
Page 261 · click to enlarge
Page 261

Avis relatif à l’utilisation

Pour les Etats-Unis : cette imprimante est certifiée conforme aux provisions DHHS 21 CFR alinéa J concernant les produits laser de Classe I (1). Pour les autres pays : cette imprimante répond aux normes IEC 60825-1 relatives aux produits laser de Classe I.

de laser

Les produits laser de Classe I sont considérés comme des produits non dangereux. L'imprimante contient un laser interne de classe IIIb (3b) ; il s'agit d'un laser semi- conducteur à arséniure de gallium de 5 mw en aluminim utilisant la plage de la longueur d'ondes située entre 770 et 795 nanomètres. L’imprimante et son système laser sont conçus pour impossible, dans des conditions normales d’utilisation, d’entretien par l’utilisateur ou de révision, l’exposition à des rayonnements laser supérieurs à des rayonnements de Classe I .

Avvertenze sui prodotti

Questa stampante è certificata negli Stati Uniti per essere conforme ai requisiti del DHHS 21 CFR Sottocapitolo J per i prodotti laser di classe 1 ed è certificata negli altri Paesi come prodotto laser di classe 1 conforme ai requisiti della norma CEI 60825-1.

laser

I prodotti laser di classe non sono considerati pericolosi. La stampante contiene al suo interno un laser di Classe IIIb (3b) che è un laser all'arsenito gallio a 5 milliwatt di alluminio funzionante nell'intervallo di lunghezza d'onda di 770-795 nanometri. Il sistema laser e la stampante sono stati progettati in modo tale che le persone a contatto con la stampante, durante il normale funzionamento, le operazioni di servizio o quelle di assistenza tecnica, non ricevano radiazioni laser superiori al livello della classe 1.

Avisos sobre el láser Se certifica que, en los EE.UU., esta impresora cumple los requisitos para los productos láser de Clase I (1) establecidos en el subcapítulo J de la norma CFR 21 del DHHS (Departamento de Sanidad y Servicios) y, en los demás países, reúne todas las condiciones expuestas en la norma IEC 60825-1 para productos láser de Clase I (1).

Los productos láser de Clase I no se consideran peligrosos. La impresora contiene en su interior un láser de la clase IIIb (3b) que se trata de un láser de arseniuro de galio con 5 milivatios de aluminio que funciona en el intervalo de longitud de onda entre 770 y 795 nanómetros. El sistema láser y la impresora están diseñados de forma que ninguna persona pueda verse afectada por ningún tipo de radiación láser superior al nivel de la Clase I durante su uso normal, el mantenimiento realizado por el usuario o cualquier otra situación de servicio técnico.

Declaração sobre laser A impressora está certificada nos E.U.A. em conformidade com os requisitos da regulamentação DHHS 21 CFR Subcapítulo J para a Classe I (1) de produtos laser. Em outros locais, está certificada como um produto laser da Classe I, em conformidade com os requisitos da norma IEC 60825-1.

Os produtos laser da Classe I não são considerados perigosos. A impressora contém no seu interior um laser Classe IIIb (3b) que é nominalmente um laser de 5 miliwatts de alumínio de arseneto de gálio a operar na região de comprimento de onda de 770-795 nanómetros. O sistema e a impressora laser foram concebidos de forma a nunca existir qualquer possiblidade de acesso humano a radiação laser superior a um nível de Classe I durante a operação normal, a manutenção feita pelo utilizador ou condições de assistência prescritas.

Laserinformatie De printer voldoet aan de eisen die gesteld worden aan een laserprodukt van klasse I. Voor de Verenigde Staten zijn deze eisen vastgelegd in DHHS 21 CFR Subchapter J, voor andere landen in IEC 60825-1.

Laserprodukten van klasse I worden niet als ongevaarlijk aangemerkt. De printer bevat een interne 5 aluminium milliwatt gallium arsenide laser van Klasse IIIb (3b) die werkt in de golflengte 770-795 nanometer. Het lasergedeelte en de printer zijn zo ontworpen dat bij normaal gebruik, bij onderhoud of reparatie conform de voorschriften, nooit blootstelling mogelijk is aan laserstraling boven een niveau zoals voorgeschreven is voor klasse 1.

249 Appendix B: Notices

Page 264 of the Lexmark M412 user manual — 252 Appendix B: Notices
Page 264 · click to enlarge
Page 264

252 Appendix B: Notices

Page 265 of the Lexmark M412 user manual — 253 Appendix C: Safety Information
Page 265 · click to enlarge
Page 265

Safety Information

  • If your product is NOT marked with this symbol , it MUST be connected to an electrical outlet that is properly grounded.
  • The power cord must be connected to an electrical outlet that is near the product and easily accessible.
  • Refer service or repairs, other than those described in the operating instructions, to a professional service person.
  • This product is designed, tested and approved to meet strict global safety standards with the use of specific Lexmark components. The safety features of some parts may not always be obvious. Lexmark is not responsible for the use of other replacement parts.
  • Your product uses a laser, exercise CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
  • Your product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.

253 Appendix C: Safety Information

Safety Information

Page 266 of the Lexmark M412 user manual — 254 Appendix C: Safety Information
Page 266 · click to enlarge
Page 266
  • Si le symbole n'apparaît PAS sur votre produit, ce dernier DOIT être branché sur une prise de courant mise à la terre.
  • Le câble d'alimentation doit être connecté à une prise de courant placée près du produit et facilement accessible.
  • L'entretien et les réparations autres que ceux décrits dans les instructions d'emploi doivent être effectués par le personnel de maintenance qualifié.
  • Ce produit a été conçu, testé et approuvé pour respecter les normes strictes de sécurité globale lors de l'utilisation de composants Lexmark spécifiques. Les caractéristiques de sécurité de certains éléments ne sont pas toujours évidentes. Lexmark ne peut être tenu responsable de l'utilisation d'autres pièces de rechange.
  • Le produit utilise un laser : ATTENTION : Les commandes, les réglages et l'exécution de toute autre procédure que celle indiquée dans le présent document peuvent entraîner des risques de radiations.
  • Le produit utilise un système d'impression qui chauffe le support d'impression duquel peuvent alors se dégager des émissions. Vous devez consulter les directives générales dans la section appropriée des instructions d'emploi pour savoir comment empêcher que ces émissions ne se produisent.
  • Se il prodotto NON è contrassegnato con questo simbolo DEVE essere collegato lo stesso ad una presa elettrica con messa a terra.
  • Il cavo di alimentazione deve essere collegato ad una presa elettrica posta nelle vicinanze del prodotto e facilmente raggiungibile.
  • Per la manutenzione o le riparazioni, escluse quelle descritte nelle istruzioni operative, consultare il personale di assistenza autorizzato.
  • Il prodotto è stato progettato, testato e approvato in conformità a severi standard di sicurezza e per l’utilizzo con componenti Lexmark specifici. Le caratteristiche di sicurezza di alcune parti non sempre sono di immediata comprensione. Lexmark non è responsabile per l’utilizzo di parti di ricambio di altri produttori.
  • Poiché il prodotto in questione utilizza il laser, considerare il seguente avvertimento: ATTENZIONE: L'uso di dispositivi di controllo o di regolazione, o l'esecuzione di procedure non incluse tra quelle descritte in questa documentazione, può provocare una pericolosa esposizione alle radiazioni.
  • Il prodotto in questione utilizza un processo di stampa che riscalda i supporti di stampa; il calore generato può determinare l'emissione di sostanze dannose da parte dei supporti. Leggere attentamente la sezione riportata nelle istruzioni riguardante le operazioni di selezione dei supporti di stampa in modo da evitare la possibilità di emissioni dannose.

254 Appendix C: Safety Information

Consignes de sécurité · Norme di sicurezza

Page 267 of the Lexmark M412 user manual — 255 Appendix C: Safety Information
Page 267 · click to enlarge
Page 267
  • Falls der Drucker nicht mit diesem Symbol markiert ist, muß er an eine ordnungsgemäß geerdete Steckdose angeschlossen werden.
  • Das Netzkabel muß an eine Steckdose angeschlossen werden, die sich in der Nähe des Geräts befindet und leicht zugänglich ist.
  • Wartungsarbeiten und Reparaturen, mit Ausnahme der in der Betriebsanleitung näher beschriebenen, sollten Fachleuten überlassen werden.
  • Dieses Produkt und die zugehörigen Komponenten wurden entworfen und getestet, um beim Einsatz die weltweit gültigen Sicherheitsanforderungen zu erfüllen. Die sicherheitsrelevanten Funktionen der Bauteile und Optionen sind nicht immer offensichtlich. Sofern Teile eingesetzt werden, die nicht von Lexmark sind, wird von Lexmark keinerlei Verantwortung oder Haftung für dieses Produkt übernommen.
  • Dieses Produkt verwendet einen Laser. Wenden Sie daher besondere VORSICHT an: Die Verwendung von Kontrollen bzw. die Regulierung von Vorgängen mit Ausnahme derjenigen, die in dieser Betriebsanleitung behandelt werden, kann Sie gefährlicher Bestrahlung aussetzen.
  • Dieses Produkt verwendet ein Druckverfahren, bei dem das Druckmedium erhitzt wird. Diese Erwärmung kann zu einer Freigabe von Emissionen des Druckmediums führen. Es ist daher wichtig, daß Sie in der Betriebsanleitung den Abschnitt, der sich mit der Auswahl geeigneter Druckmedien befaßt, sorgfältig durchlesen und die dort aufgeführten Richtlinien befolgen, um der Gefahr schädlicher Emissionen vorzubeugen.
  • Si su producto NO tiene este símbolo, , es IMPRESCINDIBLE conectarlo a una toma de corriente eléctrica con toma de tierra correcta.
  • El cable de alimentación deberá conectarse a una toma de corriente situada cerca del producto y de fácil acceso.
  • Cualquier servicio o reparación deberá realizarse por parte del personal cualificado, a menos que se trate de las averías descritas en las instrucciones de utilización.
  • Este producto se ha diseñado, verificado y aprobado para cumplir los más estrictos estándares de seguridad global usando los componentes específicos de Lexmark. Puede que las características de seguridad de algunas piezas no sean siempre evidentes. Lexmark no se hace responsable del uso de otras piezas de recambio.
  • El producto utiliza un láser. Actúe con PRECAUCION: El uso de los controles o ajustes o el llevar a cabo procedimientos distintos a los especificados aquí puede causar niveles de radiación peligrosos.
  • Durante el proceso de impresión que utiliza este producto se calienta el medio de impresión, y el calor puede provocar que el medio emita gases. Para evitar emisiones peligrosas, el usuario deberá comprender y seguir lo expuesto en la sección de las instrucciones de utilización donde se describen las directrices para seleccionar el medio de impresión.

255 Appendix C: Safety Information

Sicherheitshinweise · Pautas de Seguridad

Page 270 of the Lexmark M412 user manual — 258 Appendix C: Safety Information
Page 270 · click to enlarge
Page 270
  • Si el vostre producte NO està marcat amb el símbol , S’HAURÀ de connectar a una presa elèctrica de terra.
  • El cable de potència s’haurà de connectar a una presa de corrent propera al producte i fàcilment accessible.
  • Si heu de fer una reparació que no figuri entre les descrites a les instruccions de funcionament, confieu-la a un professional.
  • Aquest producte està dissenyat, comprovat i aprovat per tal d'acomplir les estrictes normes de seguretat globals amb la utililització de components específics de Lexmark. Les característiques de seguretat d'algunes peces pot ser que no sempre siguin òbvies. Lexmark no es responsabilitza de l'us d'altres peces de recanvi.
  • El vostre producte funciona amb un làser. Procediu amb PRECAUCIÓ: La utilització de controls, els ajustaments o la realització de procediments distints dels especificats aquí poden donar lloc a una exposició a radiacions perillosa.
  • El vostre producte fa servir un procediment d’impressió que escalfa el mitjà d’impressió, i la calor pot fer que aquest mitjà alliberi emissions. Llegiu atentament l’apartat de les instruccions de funcionament on s’exposen les directrius de selecció del mitjà d’emissió per tal d’evitar la possibilitat d’emissions nocives.

Turvaohjeet

  • Jos tuotteessa ei ole tätä tunnusta, , sen saa kytkeä vain maadoitettuun pistorasiaan.
  • Tuotteen verkkojohto on kytkettävä sitä lähellä olevaan pistorasiaan. Varmista, että kulku pistorasian luo on esteetön.
  • Muut kuin käyttöohjeissa mainitut huoltotai korjaustoimet on jätettävä huoltoedustajalle.
  • Tämä tuote on testattu ja hyväksytty. Se täyttää korkeat maailmanlaajuiset turvallisuusvaatimukset, kun siinä käytetään tiettyjä Lexmarkin valmistusosia. Joidenkin osien turvallisuusominaisuudet eivät aina ole itsestään selviä. Lexmark ei vastaa muiden kuin alkuperäisten osien käytöstä.
  • Laite sisältää lasertuotteen. Varoitus: Muiden kuin tässä mainittujen säätöjen tai toimien teko voi saattaa käyttäjän alttiiksi vaaralliselle säteilylle.
  • Tulostusmateriaali kuumenee tulostusprosessin aikana. Lämmön vaikutuksesta materiaalista saattaa irrota haitallisia aineita. Voit välttää haitalliset päästöt noudattamalla käyttöohjeissa annettuja tulostusmateriaalien valintaohjeita.

258 Appendix C: Safety Information

Informació de Seguretat

Page 272 of the Lexmark M412 user manual — 260 Appendix C: Safety Information
Page 272 · click to enlarge
Page 272
Lexmark M412 — Turvaohjeet diagram (page 272)
Fig. 97 · Turvaohjeet
Lexmark M412 — Turvaohjeet diagram (page 272)
Fig. 98 · Turvaohjeet
Lexmark M412 — Turvaohjeet diagram (page 272)
Fig. 99 · Turvaohjeet
Lexmark M412 — Turvaohjeet diagram (page 272)
Fig. 100 · Turvaohjeet

260 Appendix C: Safety Information

Page 273 of the Lexmark M412 user manual — 261 Appendix C: Safety Information
Page 273 · click to enlarge
Page 273
Lexmark M412 — Turvaohjeet diagram (page 273)
Fig. 101 · Turvaohjeet
Lexmark M412 — Turvaohjeet diagram (page 273)
Fig. 102 · Turvaohjeet
Lexmark M412 — Turvaohjeet diagram (page 273)
Fig. 103 · Turvaohjeet

261 Appendix C: Safety Information

Page 274 of the Lexmark M412 user manual — 262 Appendix C: Safety Information
Page 274 · click to enlarge
Page 274
Lexmark M412 — Turvaohjeet diagram (page 274)
Fig. 104 · Turvaohjeet
Lexmark M412 — Turvaohjeet diagram (page 274)
Fig. 105 · Turvaohjeet
Lexmark M412 — Turvaohjeet diagram (page 274)
Fig. 106 · Turvaohjeet

262 Appendix C: Safety Information

Page 275 of the Lexmark M412 user manual — 263 Appendix C: Safety Information
Page 275 · click to enlarge
Page 275
Lexmark M412 — Turvaohjeet diagram (page 275)
Fig. 107 · Turvaohjeet

263 Appendix C: Safety Information

Page 276 of the Lexmark M412 user manual — 264 Appendix C: Safety Information
Page 276 · click to enlarge
Page 276

264 Appendix C: Safety Information

Page 277 of the Lexmark M412 user manual — 265 Appendix D: Warranty
Page 277 · click to enlarge
Page 277

D Warranty

Statement of Limited

Lexmark International, Inc., Lexington, KY

Warranty

This warranty applies to the United States and Canada. For customers outside the U.S. and Canada, refer to the country-specific warranty information that came with your printer.

Lexmark Optra M410 and

This Statement of Limited Warranty applies to this product if it was originally pur- chased for your use, and not for resale, from Lexmark or a Lexmark remarketer, referred to in this statement as “Remarketer.”

M412 Laser Printers

Warranty Lexmark warrants that this product:

  • Is manufactured from new parts, or new and serviceable used parts, which perform like new parts,
  • Is free from defects in material and workmanship,
  • Conforms to Lexmark’s official published specifications, and
  • Is in good working order.

If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair without charge.

If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was designed. To obtain warranty service, you may be required to present the feature or option with the product.

If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.

265 Appendix D: Warranty

Page 278 of the Lexmark M412 user manual — 266 Appendix D: Warranty
Page 278 · click to enlarge
Page 278

Warranty Service The warranty period is 12 months and starts on the date of original purchase as shown on the purchase receipt.

To obtain warranty service you may be required to present proof of original purchase. Warranty service will be provided at your location.at a Remarketer or a Lexmark desig- nated location. You may be required to deliver your product to the Remarketer or Lex- mark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the designated location.at a Lexmark designated location.

  • at your location.
  • at a Remarketer or a Lexmark designated location. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the designated location.
  • at a Lexmark designated location.

When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item. The replacement item assumes the remaining warranty period of the original product.

Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, or damaged beyond repair. Also, such product must be free of any legal obligation or restrictions that prevent its exchange.

Before you present this product for warranty service, remove all programs, data, and removable storage media.

For further explanation of your warranty alternatives and the nearest Lexmark autho- rized servicer in your area, please contact Lexmark at 1-800-LEXMARK (1-800-539- 6275), or on the World Wide Web at http://www.lexmark.com

Free remote technical support is provided for this product throughout its warranty period. Lexmark offers a variety of extended warranty programs that include an exten- sion of technical support. For products no longer covered by a Lexmark warranty, tech- nical support may only be available for a fee.

Extent of Warranty We do not warrant uninterrupted or error-free operation of a product.

Warranty service does not include repair of failures caused by:

  • modification or attachments
  • accidents or misuse
  • unsuitable physical or operating environment
  • maintenance by anyone other than Lexmark or a Lexmark authorized servicer
  • operation of a product beyond the limit of its duty cycle
  • failure to have installed a maintenance kit as specified (if applicable)
  • use of printing media outside of Lexmark specifications
  • use of other than Lexmark supplies (such as toner cartridges, inkjet cartridges, and ribbons)
  • use of other than Lexmark product or component

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WAR- RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR- POSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD.

266 Appendix D: Warranty

Page 279 of the Lexmark M412 user manual — 267 Appendix D: Warranty
Page 279 · click to enlarge
Page 279

Limitation of Liability Your sole remedy under this Statement of Limited Warranty is set forth in this section. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this Statement of Limited Warranty, you may recover actual damages up to the limit set forth in the following paragraph.

Lexmark's liability for actual damages from any cause whatsoever will be limited to the greater of 1) $5,000 or 2) the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. In no event will Lexmark be liable for any lost profits, lost savings, incidental damage, or other economic consequential damages. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.

This limitation of remedies also applies to any developer of materials supplied to Lex- mark. Lexmark’s and the developer’s limitations of remedies are not cumulative. Such developer is an intended beneficiary of this limitation.

Additional Rights Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

267 Appendix D: Warranty

Page 280 of the Lexmark M412 user manual — 268 Appendix D: Warranty
Page 280 · click to enlarge
Page 280

268 Appendix D: Warranty

Page 281 of the Lexmark M412 user manual — 269 Glossary
Page 281 · click to enlarge
Page 281

Glossary

Numerics 7 3/4 Envelope. See Monarch.

9 Envelope. An envelope measuring 98.4 x 225.4 mm (3.875 x 8.875 in.).

10 Envelope. See Com-10.

500-sheet optional drawer. An optional input tray and drawer you can purchase for the printer to increase input capacity.

1200 Image Quality. A print resolution setting that lets the printer to vary the size of each printed pixel, thereby producing a continuous tone effect. This setting improves the print quality of graphic fills, images, and halftones.

A A4. Print material measuring 210 x 297 mm (8.27 x 11.7 in.).

A5. Print material measuring 148 x 210 mm (5.83 x 8.27 in.).

all points addressable (APA). In computer graphics, the ability to address and display, or not display, each picture element (pel) on a display surface.

APA. See all points addressable.

application. See software application.

269 Glossary

Page 282 of the Lexmark M412 user manual — 270 Glossary
Page 282 · click to enlarge
Page 282

attendance message. An operator panel message that describes a printer problem. Operator intervention is required before the printer can continue processing.

automated fax system. A Lexmark system for providing customers with quick product information, technical tips, and printer driver information.

automatic interface. A printer function that determines the active interface: parallel, serial, network, infrared, LocalTalk, or USB.

B B5. (1) Envelope measuring 176 x 250 mm (6.93 x 9.84 in.). (2) Print material measuring 182 x 257 mm (7.17 x 10.12 in.).

baud. The rate, in bits per second (bps), at which data is transferred to or from the computer through the serial interface.

bidirectional communication. Two-way communication between the printer and a computer, using Network Printing Alliance Protocol (NPAP 1.0 standard).

bin. See output bin.

bitmapped font. Predefined pattern of bits that represent a typeface at a specific size, style, and resolution.

bits per second (bps). A measurement of the speed of data transferred through a serial interface.

bps. See bits per second.

buffer. A portion of memory used to temporarily store data.

270 Glossary

Page 283 of the Lexmark M412 user manual — 271 Glossary
Page 283 · click to enlarge
Page 283

Busy. A printer state in which the printer is processing data or printing pages.

byte. A group of eight binary digits processed as a unit. Typically used to represent an alphanumeric character.

C C5. Envelope measuring 162 x 229 mm (6.38 x 9.01 in.).

card stock. Heavy, single-ply print material frequently used for reports or book covers.

Centronics parallel interface. A standard for connecting printers and other peripheral devices to a computer. It defines the plug, socket and electrical signals that are used for controlling the transmission of data.

characters per inch (cpi). The number of characters that can be printed in one inch.

Com-10. Also called a 10 Envelope. An envelope measuring 104.8 x 241.3 mm (4.125 x 9.5 in.).

configuration. (1) The arrangement of a computer system, printer, or network. (2) The devices and programs that make up a system, subsystem, or network.

corona wire. A thin wire in the printer that electrically charges the print material to attract toner from the photoconductor.

curl. Curvature at the edge of a sheet of print material.

D Data Set Ready (DSR). A “handshaking” signal contained in a serial interface indicating the device is ready to exchange information.

data stream. Print data and printer control information that flows from the host system (computer) to the printer without interruption.

271 Glossary

Page 284 of the Lexmark M412 user manual — 272 Glossary
Page 284 · click to enlarge
Page 284

Data Terminal Ready (DTR). A “handshaking” signal contained in a serial interface indicating the device is ready to exchange information.

default. An attribute, value, or setting that is assumed when none is explicitly specified.

disk. See hard disk option.

display. See operator panel display.

DL. Envelope measuring 110 x 220 mm (4.33 x 8.66 in.).

download. To transfer information, such as fonts, from a diskette or other device to your computer or printer for temporary or permanent storage.

dpi. Dots per inch. See resolution.

DRAM. See dynamic random access memory.

driver. See printer driver.

DSR. See Data Set Ready.

DTR. See Data Terminal Ready.

duplex. To print on both sides of a sheet of print material.

dynamic random access memory (DRAM). Memory that allows rapid storage and retrieval of data. DRAM contents are erased when electrical power is turned off.

E emulation. Imitation of a printer processing language. For example, PCL 6 emulation imitates the Hewlett-Packard LaserJet printer language.

ENA. External network adapter. See external print server.

error message. See attendance message.

272 Glossary

Page 285 of the Lexmark M412 user manual — 273 Glossary
Page 285 · click to enlarge
Page 285

Ethernet. A network with a bus topology that utilizes carrier sense multiple access with collision detection (CSMA/CD). An Ethernet network may be installed using any of three cabling systems:

  • Ethernet 10Base2 (using RG-58 coax)
  • Ethernet 10BaseT (using telephone twisted pair cable)
  • Ethernet 100BaseTX

executive. Print material measuring 184.2 x 266.7 mm (7.25 x 10.5 in.).

external network adapter (ENA). See external print server.

external print server. Also called an external network adapter (ENA). A LAN device that attaches externally to the printer and lets you connect various printers to your network, thereby freeing dedicated PC print servers for use as LAN workstations.

F factory default. Printer setting defined when the printer is manufactured.

Fastbytes protocol. A parallel printer protocol that enables the printer to receive information at faster than normal transmission rates.

fixed-pitch font. A font that prints each character in a fixed amount of horizontal space, regardless of the width of the character. These fonts are identified by the number of characters that print in 1 inch of horizontal line space, such as 10 pitch or 12 pitch.

flash memory. Optional memory you can install in the printer to provide non-volatile storage for downloaded fonts, symbol sets, or macros.

273 Glossary

Page 286 of the Lexmark M412 user manual — 274 Glossary
Page 286 · click to enlarge
Page 286

font. A family or set of characters that have common visual characteristics, such as size, weight, and style; for example, Arial Bold.

fuser. The part of the printer that uses heat and pressure to make toner adhere to the print material.

G grain. The alignment of the paper fibers in a sheet of print material. For example, in grain long paper, the fibers run the length of the page.

g/m². Grams per square meter. Metric measurement for print material weight.

H handshaking. The exchange of predetermined signals when a connection is established.

hard disk option. An optional device you can install in the printer to provide non-volatile storage for downloaded fonts, symbol sets, or macros.

hex trace. A diagnostic printer mode that lets you print the uninterpreted printer data stream so you can see a hexadecimal and character representation of a print job.

Honor INIT. A printer setting that allows the printer to be reset by an initialization signal sent from the computer.

I images. Visual data typically scanned from original sources external to the PC, such as photographs or video frames.

INA. Internal network adapter. See internal print server.

infrared adapter. An external device that uses a low- power infrared beam to allow a computer to exchange data with a printer without a physical connection between the two.

274 Glossary

Page 287 of the Lexmark M412 user manual — 275 Glossary
Page 287 · click to enlarge
Page 287

input source. A printer tray or the multipurpose feeder. An input source holds print material for printing.

Integrated Network Option. See print server.

interface. The connection between the computer and the printer.

internal network adapter (INA). See internal print server.

internal print server. Also called an internal network adapter (INA). An optional card you can install in the printer to connect it to a local area network (LAN).

J job accounting. A printer feature that lets you store statistical information about most recent printer jobs on a hard disk option installed in the printer.

job buffering. A printer feature that lets you spool print jobs to a hard disk option installed in the printer.

K KB. Kilobyte; 1024 bytes.

L LAN. See local area network.

landscape orientation. Printed page orientation in which the width of the page is greater than the height.

LCD. See liquid crystal display.

leading edge. The edge of the printed page that exits the printer first.

legal. Print material measuring 215.9 x 356 mm (8.5 x 14 in.).

letter. Print material measuring 215.9 x 279.4 mm (8.5 x 11 in.).

275 Glossary

Page 288 of the Lexmark M412 user manual — 276 Glossary
Page 288 · click to enlarge
Page 288

lines per page (lpp). The number of lines of text that can be printed on one page.

link. The connection between the computer system or local area network and the printer.

liquid crystal display (LCD). The display technology that shows operator panel messages and menu selections.

local area network (LAN). A computer network located on a user’s premises within a limited geographical area.

long-edge binding. A printer setting that arranges the orientation and layout of a duplexed page to be bound along the long side of the page.

LPTx. A representation of one of the logical parallel ports (for example, LPT1) on a personal computer.

M macro. A collection of commands grouped together and temporarily or permanently stored in printer memory.

manual feed. A process of feeding print material (paper, envelope, label, transparency, card stock) into the multipurpose feeder on the printer one sheet at a time.

MarkNet S. Family of multi-protocol Lexmark internal print servers. Ethernet and Token-Ring versions are available.

MarkNet XLe. Family of multi-protocol Lexmark external print servers. Ethernet, Token-Ring, and LocalTalk versions are available.

MarkVision. A printer utility that provides continuous printer status and lets you configure multiple printers from a single setup file.

MB. Megabyte; 1,048,576 bytes.

media. See print material.

276 Glossary

Page 289 of the Lexmark M412 user manual — 277 Glossary
Page 289 · click to enlarge
Page 289

menu. A list of choices that control printer operation, printer features, and the appearance of the printed page.

menu item. See setting.

Monarch. Also called a 7 3/4 Envelope. An envelope measuring 98.4 x 190.5 mm (3.875 x 7.5 in.).

monospaced font. A font in which the space for each character does not vary, regardless of the width of the character.

multipurpose feeder. A print material input source on the front of the printer that lets you load a small stack of paper, envelopes, transparencies, labels, and odd-size print material. You can also use the multipurpose feeder to manually feed print material into the printer one sheet at a time.

N network. A group of computers, printers, and other hardware devices connected to each other to share information.

network adapter. See print server.

non-volatile random access memory (NVRAM). Memory that allows rapid storing and retrieving of data. NVRAM contents are preserved when electrical power is turned off.

Not Ready. A printer state in which the printer does not accept data from the computer. This state is initiated either by operator intervention or a printer error.

O operating system. The basic software which provides the low-level functions needed to operate your computer, such as booting up.

Operation ReSource. A Lexmark process established to recycle toner cartridges and print units.

277 Glossary

Page 290 of the Lexmark M412 user manual — 278 Glossary
Page 290 · click to enlarge
Page 290

operator panel. The buttons and liquid crystal display (LCD) on the printer that are used to change printer settings and display printer status.

operator panel display. The liquid crystal display on the operator panel that shows printer menus and messages.

operator panel overlay. An adhesive label with translated names for the operator panel display buttons and numbers in one language. A package of overlays is supplied for you to select the label with the language you need.

orientation. A page description defining whether the printed text runs along the short edge (portrait) or the long edge (landscape) of the page.

Other Envelope. Value to select for all envelopes that are not a standard size; defaults to 229.11 x 356 mm (9.02 x 14 in.). Set the actual size of the envelope from your software application.

output bin. A print material exit area. The default is the standard output bin, located on top of the printer. A rear output bin, located on the back of the printer, is also available.

overlay. Background text or graphics that appear consistent in each file that uses the overlay.

P pages per minute (ppm). The number of typical pages of text that can be printed in one minute.

paper. See print material.

paper guides. The length guide and the width guide located in an input tray that define proper placement of print material. Failing to properly adjust these guides may result in paper jams.

278 Glossary

Page 291 of the Lexmark M412 user manual — 279 Glossary
Page 291 · click to enlarge
Page 291

paper type. A printer setting that defines the type of print material (plain paper, card stock, transparency, label, bond, letterhead, preprinted, colored paper, envelope, or custom) loaded in a specified input source.

parallel interface. A bidirectional interface for exchanging data between the computer and the printer.

parallel/USB interface option card. An optional card that connects your printer to a parallel interface and a Universal Serial Bus (USB).

pel. Picture element. The smallest addressable unit that can be effectively reproduced by the printer.

photoconductor. An element of the print unit that works like film in a camera. As the photoconductor drum rotates, it uses positive and negative charges to alternately attract the toner necessary to define the image produced by the laser and transfer the image to the page. Fingerprints or scratches on the photoconductor prevent proper toner transfer and may result in reduced print quality.

pitch. A unit of measure that determines the number of characters that can be printed in 1 horizontal inch. For example, a 10-pitch font prints 10 characters per inch (cpi).

point. A unit of measure that determines the height of a printed character (1 point = 1/72 in.).

point size. The height of the characters in a font.

portrait orientation. Printed page orientation in which the height of the page is greater than the width.

power saver. A printer setting that reduces power usage when the printer is idle. When the Power Saver message displays, the printer is ready to receive print jobs.

ppm. See pages per minute.

PQET. See Print Quality Enhancement Technology.

279 Glossary

Page 292 of the Lexmark M412 user manual — 280 Glossary
Page 292 · click to enlarge
Page 292

precharger wire. A wire inside the print unit that electrically charges the photoconductor during the printing process.

Print and Hold job. A print job sent from your software application, stored in printer memory, and accessed at a later time from the CONFIDENTIAL JOB menu item or the HELD JOBS menu item. A Print and Hold job lets you delay the printing of a job, print it later, ask for additional copies, verify one copy before printing more, and access confidential print jobs by using a Personal Identification Number (PIN).

print cartridge. The replaceable unit inside the printer that contains the photoconductor and toner supply.

print material. Any material you print on, such as paper, card stock, envelopes, labels, and transparencies.

Print Quality Enhancement Technology (PQET). A printer feature that improves the quality of text by smoothing the edges of characters and lines.

print server. A device that lets you connect the printer to a local area network (LAN).

printer driver. A program that translates software application language to printer language so data can be transferred.

printer language. A set of defined commands (such as PCL or PostScript) to which the printer responds.

printer memory. See dynamic random access memory (DRAM) or random access memory (RAM).

proportionally spaced font. A font that varies the width of the character to allow uniform spacing around characters.

protocol. A set of rules governing the communication and data transfer between two or more devices.

280 Glossary

Page 293 of the Lexmark M412 user manual — 281 Glossary
Page 293 · click to enlarge
Page 293

R RAM. See random access memory.

random access memory (RAM). Memory that allows rapid storage and retrieval of data. RAM contents are erased when electrical power is turned off.

Ready. A printer state in which the printer can receive, process, and print data.

resolution. A measure of the sharpness of a printed image, expressed in the number of dots per inch (dpi).

S scalable font. A font whose characters are stored only as outlines so it is easy to change (or scale) the size of the characters (measured in points).

screen font. A downloadable font that appears the same on the computer screen as it does on a printed page.

serial interface. A way of communicating between computer and printer by transmitting data one bit at a time.

server. A device that allows the sharing of resources, such as printers, on a network.

service message. An operator panel display message that indicates the printer needs service.

setting. Values you choose from printer menus or software applications that control printer operation and the appearance of the printed page.

setup utility. A program provided with the printer that installs printer drivers, tests printer setup, and completes the setup of printer options.

short-edge binding. A printer setting that arranges the orientation and layout of a duplexed page to be bound along the short side of the page.

simplex. See single-sided printing.

281 Glossary

Page 294 of the Lexmark M412 user manual — 282 Glossary
Page 294 · click to enlarge
Page 294

single-sided printing. Printing on only one side of a sheet of print material (simplex printing).

SmartSwitch. A printer function that automatically switches the printer language to match that of the current print job.

software application. Any program loaded on your computer used to perform a specific task, such as word processing or data compiling.

Standard protocol. A parallel printer protocol where the printer receives information sent from the computer at a normal transmission rate.

status message. A operator panel display message that provides information on the state of the printer.

symbol set. A unique set of alphanumeric characters and symbols that the printer uses to print the requested font. Different symbol sets offer the diverse characters required for different languages or symbol-intense applications.

system board. The printer main circuit board.

T timeout. A time interval allotted for certain operations.

Token-Ring. A type of network communication that conforms to IEEE 802.5 standard. The name is derived from its physical ring configuration and the passing of a token from print server to print server.

toner. The material that adheres to the print material to create a printed page.

toner cartridge. See print cartridge.

tray linking. A means of increasing input source capacity by feeding print material from one input source until it is empty and then automatically feeding print material from another input source.

282 Glossary

Page 295 of the Lexmark M412 user manual — 283 Glossary
Page 295 · click to enlarge
Page 295

Tri-Port interface option card. An optional card you can install inside the printer to add support for LocalTalk, serial, and infrared interfaces.

TrueType fonts. Fonts that use a single font outline for both screen display and printing. You can use TrueType fonts in Windows applications and scale them to any height. They print exactly as they appear on the screen.

type size. A measurement in pitch or points of a graphic character in a font.

type style. The form or shape of the characters in a font.

typeface. The style that defines a group of characters and symbols.

typographic fonts. Fonts whose characters are spaced proportionally on the page according to character width.

U Universal. Value to select for all print material excluding envelopes loaded in the multipurpose feeder that is not a standard size; defaults to 215.9 x 356 mm (8.5 x 14 in.). Set the actual size of the page from your software application.

Universal Serial Bus (USB). An industry accepted serial bus for external devices. It replaces all the different types of serial and parallel ports with one standardized plug.

USB. See Universal Serial Bus.

user default. Printer setting selected by a user that remains in effect until a new user default is chosen.

V value. One of the settings available for a menu item.

283 Glossary

Page 296 of the Lexmark M412 user manual — 284 Glossary
Page 296 · click to enlarge
Page 296

W watermark. See overlay.

weight. The thickness of the typeface line or the thickness of print material.

284 Glossary

Page 297 of the Lexmark M412 user manual — Table of Contents
Page 297 · Contents
Contents

Contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 298 of the Lexmark M412 user manual — Table of contents
Page 298 · click to enlarge
Page 298

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 299 of the Lexmark M412 user manual — Table of contents
Page 299 · click to enlarge
Page 299

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 300 of the Lexmark M412 user manual — Table of contents
Page 300 · click to enlarge
Page 300

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 301 of the Lexmark M412 user manual — Table of contents
Page 301 · click to enlarge
Page 301

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 302 of the Lexmark M412 user manual — Table of contents
Page 302 · click to enlarge
Page 302

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 303 of the Lexmark M412 user manual — Table of contents
Page 303 · click to enlarge
Page 303

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 304 of the Lexmark M412 user manual — Table of contents
Page 304 · click to enlarge
Page 304

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 305 of the Lexmark M412 user manual — Table of contents
Page 305 · click to enlarge
Page 305

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 306 of the Lexmark M412 user manual — Table of contents
Page 306 · click to enlarge
Page 306

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 307 of the Lexmark M412 user manual — Table of contents
Page 307 · click to enlarge
Page 307

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 308 of the Lexmark M412 user manual — Table of contents
Page 308 · click to enlarge
Page 308

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 309 of the Lexmark M412 user manual — Table of contents
Page 309 · click to enlarge
Page 309

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 310 of the Lexmark M412 user manual — Table of contents
Page 310 · click to enlarge
Page 310

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 311 of the Lexmark M412 user manual — Table of contents
Page 311 · click to enlarge
Page 311

Table of contents

Introductionp.9About This Bookp.9Other Informationp.10Online Documentsp.10Trademarksp.11Setting Up YourPrinterp.13Unpacking YourPrinterp.13Removing Print Cartridge Packagingp.14Installing the PrintCartridgep.17Loading the Standard InputTrayp.18Installing the Paper Bailp.23Connecting Your Printer to a Computerp.24Using a ParallelCablep.24Using a USB Cablep.26For Windows 2000 users:p.26For Windows 98 users:p.27For Macintosh users:p.30Plugging the PrinterInp.32Turning the Printer Power Onp.32Printing the Menu Settings Pagep.33Installing the Operator Panel Overlayp.34Changing the Operator Panel Display Languagep.35Installing Printer Drivers and Utilitiesp.36MarkVisionp.37MarkVision Printer Management Softwarep.37Operating Systems Supportedp.37Introducing MarkVisionp.37MarkVision for Intranet Serversp.38Introducing MarkVision for Intranet Serversp.38Mapsp.39Filtersp.39Remote Updatesp.39MarkVision for UNIX Networksp.39Lexmark MarkTrackp.40Lexmark NetPnPp.41Software Installation and Distribution Toolsp.41Optra Formsp.42Solaris Ready Printers for Sun Customersp.43Using the Operator Panel and Menusp.45Using the OperatorPanelp.46Printer Indicator Lightp.46Operator Panel Buttonsp.47Printer Messagesp.49Status Messagesp.49Attendance Messagesp.49Service Messagesp.49Operator Panel Menusp.50Printing the Menu Settings Pagep.51Changing MenuSettingsp.52Disabling the Operator Panel Menusp.53Overview of PrinterMenusp.55Paper Menup.56Finishing Menup.65Utilities Menup.69Job Menup.71Quality Menup.83Setup Menup.85PCL Emul Menup.91PostScript Menup.95Parallel Menup.96Serial Menup.99Network Menup.103Infrared Menup.105LocalTalk Menup.108USB Menup.111Fax Menup.114Config Menup.118Understanding Print and HoldJobsp.120Confidential Jobsp.120Held Jobsp.121Repeat Print Jobp.121Reserve Print Jobp.121Verify Print Jobp.122Printing and Deleting Held Jobsp.123Entering a Personal Identification Number (PIN)p.123Print and Hold Formatting Errorsp.125Using Print Materialsp.127Paper Sources andSizesp.128Print Material Guidelinesp.130Paperp.130Letterheadp.130Transparenciesp.131Envelopesp.131Labelsp.132Card Stock Guidelinesp.134Storing Print Materialp.135Loading PrintMaterialp.136Loading an InputTrayp.136Loading the Multipurpose Feederp.142Using the PaperExits (Output Bins)p.145Using the StandardOutput Binp.145Using the RearOutput Binp.146Printing on Letterheadp.147Tray Linkingp.147Manual Duplex Printingp.148Duplex Printing from the Multipurpose Feederp.148Duplex Printing from the Traysp.148Avoiding PaperJamsp.149Multipurpose Feederp.151Multipurpose Feeder Guidelinesp.152Opening the Multipurpose Feederp.153Loading the Multipurpose Feederp.155Loading Print Materialp.155Using the Multipurpose Feederp.161Closing the Multipurpose Feederp.162Understanding Printer Messagesp.163Status Messagesp.163Line 1 Messagesp.164Warning Messagesp.170Attendance Messagesp.171Solving Printer Problemsp.185Display Problemsp.187Printing Problemsp.188Print Quality Problemsp.190Option Problemsp.192Network Printing Problemsp.193Other Problems and Questionsp.194Clearing Jamsp.195Possible Paper Jam Areasp.196200 and 201 Paper Jam - Remove Cartridgep.196202 Paper Jam - Open Rear Doorp.198Before Reaching the Standard Output Binp.198Exiting to the Standard Output Binp.201203 Paper Jam - ShortPaperp.202250 Paper Jam - Check MP Feederp.204Maintaining Your Printerp.205Ordering a Print Cartridgep.205Storing the Print Cartridgep.206Replacing the Print Cartridgep.206Cleaning the Printhead Lensp.207Ordering a ChargeRoll Kitp.207Faxp.209Understanding the Fax Portp.209Choosing Hardwarep.209Setting Up a FaxPortp.210Resetting a FaxPortp.211Disabling a FaxPortp.212Memory and Option Cardsp.213Accessing the Printer System Boardp.213Understanding Memory Optionsp.218Printer Memoryp.218Flash Memoryp.218Installing MemoryOptionsp.219Removing MemoryOptionsp.222Understanding OptionCardsp.223Internal Print Server (Internal Network Adapter or INA)p.223Installing the Optional Internal Print Serverp.223Tri-Port Interface Option Cardp.224Installing the Tri-Port Interface Option Cardp.224Hard Disk Optionp.224Attaching a Hard Disk to the Adapter Cardp.225Installing the Hard Disk Option Cardp.226Parallel/USB Interface OptionCardp.227Installing the Parallel/USB Interface Option Cardp.227Installing an OptionCardp.228Removing an Option Cardp.231Closing the Printer System Boardp.232Optional 500-Sheet Drawerp.235Installing the Optional Drawerp.235Infrared Adapterp.239Connecting the Cable and Using the Infrared Adapterp.239Verifying the Installation of Optionsp.241Printing the Menu Settings Pagep.241Understanding Fontsp.243Typefaces andFontsp.243Weight and Stylep.243Pitch and Point Sizep.244Bitmapped and Scalable Fontsp.246Resident Fontsp.247Symbol Setsp.251Symbol Sets for PCL6 Emulationp.251Downloadable Fontsp.253Printing a Font Sample Listp.254Noticesp.255Safety Informationp.265Turvaohjeetp.270Warrantyp.277Glossaryp.281Numericsp.281Ap.281Bp.282Cp.283Dp.283Ep.284Fp.285Gp.286Hp.286Ip.286Jp.287Kp.287Lp.287Mp.288Np.289Op.289Pp.290Rp.293Sp.293Tp.294Up.295Vp.295Wp.296Indexp.297
Page 312 of the Lexmark M412 user manual — 300 Index
Page 312 · click to enlarge
Page 312

300 Index

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Menus Disabled status message appears on the display.The operator panel menus are disabled. To enable the menus: • Turn the printer power Off (O). • Press and hold Select and Return, and then turn the printer power On (|). • Release the buttons when Performing Self Test displays. Once the printer finishes powering on, the CONFIG MENU displays. • Press Menu> until Panel Menus displays on the second line. Press Select. • Press Menu> until Enable displays on the second line. Press Select. The Saved message briefly appears and then, the Enabling Menus displays. The CONFIG MENU displays again with Panel Menu on the second line. • Press Menu> until Exit Config Menu displays on the second line. Press Select. Activating Menu Changes briefly appears, and then Performing Self Test briefly appears. The printer returns to the Ready state. If the operator panel menus are password protected, see your system adminis- trator. p.187
Display shows only diamonds or is blank.• Turn the printer power Off (O), wait about 10 seconds, and turn the printer power On (|). • The Performing Self Test message appears on the operator panel display. When the test is completed, the Ready message displays. If the messages do not display, turn the printer power Off (O) and call Lexmark Customer Support Center. p.187
Menu settings changed from the operator panel have no effect.Settings in the software application, the printer driver, or the printer utilities are overriding the settings in the operator panel. • Change the menu settings from the printer driver, the printer utilities, or the software application instead of the operator panel. • Disable the settings in the printer driver, the printer utilities, or the software application so you can change settings from the operator panel. p.187
Job did not print or incorrect characters printed.Make sure the Ready status message appears on the operator panel display before you send a job to print. Press Go to return the printer to the Ready status message. p.188
Job did not print or incorrect characters printed.Make sure there is print material loaded in the printer. Press Go to return the printer to the Ready status message. p.188
Job did not print or incorrect characters printed.Verify that the printer is using the correct printer language. p.188
Job did not print or incorrect characters printed.• Verify that the correct printer driver is being used. • Make sure the parallel cable or USB cable is firmly plugged in at the back of the printer. • Check the cable connection. Make sure you are using the correct cable. If you use the parallel port, we recommend a IEEE 1284-compliant parallel cable such as Lexmark part number 1329605 (10 ft) or 1427498 (20 ft). If you use the USB port, we recommend the cable with Lexmark part number 12A2405 (2M). • If the printer is connected through a switch box, try a direct connection. • Verify that the correct paper size is selected through the operator panel, in the printer driver, or in the software application setting. • Make sure PCL SmartSwitch and PS SmartSwitch are set to On. • If a print spooler is used, verify that the spooler is not stalled. • If you print across a network or on a Macintosh, see “Network Printing Problems” on page 181. p.188
Job did not print or incorrect characters printed.Determine which host interface you are using. Print a menu settings page to verify that the current interface settings are correct. See “Printing the Menu Settings Page” on page 39 for more information. If you are using serial interface: • Make sure Honor DSR is set to Off. • Check the protocol, baud, parity, and data bit settings. The settings on the printer and on the host computer should match. p.188
You are connected to the USB port, but the printer will not print.Make sure you are using Windows 98 or other USB-capable operating system supported by Lexmark. p.188
Print material misfeeds or multiple feeds occur.• Make sure the print material you are using meets the specifications for your printer. See “Print Material Guidelines” on page 118 for more information. • Flex print material before loading it in any of the paper sources. • Make sure the print material is loaded correctly. • Make sure the paper width and length guides on the paper sources are adjusted correctly and are not too tight. • Do not overfill the paper sources. • Do not force print material into the multipurpose feeder when you load it; otherwise, it may skew or buckle. • Remove any curled print material from paper sources. • If there is a recommended print side for the print material, load the print material as described in “Print Material Guidelines” on page 118. • Load less print material in the input sources. • Turn the print material over or around and try printing again to see if feeding improves. • Do not mix print material types. • Do not mix reams of print material. • Remove the top and bottom sheets of a ream before loading the print material. • Load an input source only when it is empty. p.189
You get unexpected page breaks.Check the Print Timeout setting in the SETUP MENU. Increase the setting. See Print Timeout on page 74 for more information. p.189
Job prints from the wrong input source or on the wrong print material.Check the PAPER TYPE setting in the PAPER MENU on the operator panel and in the printer driver. See PAPER TYPE on page 47 for more information. p.189
Print material does not stack neatly in an output bin.• Turn the print material stack over in the tray or multipurpose feeder. • If the print material is exiting to the standard output bin, make sure the paper bail is installed correctly. See “Installing the Paper Bail” on page 11 for more information. p.189
Print is too light.• Check the toner supply. • Change the Toner Darkness setting in the QUALITY MENU. See Toner Darkness on page 71 for more information. • If you are printing on an uneven print surface, change the PAPER WEIGHT and PAPER TEXTURE settings in the PAPER MENU. See PAPER TYPE on page 47 for more information. • Verify that the correct print material is being used. p.190
Toner smears or print comes off the page.• If you are printing on an uneven print surface, change the PAPER TEXTURE and PAPER WEIGHT settings in the PAPER MENU. See PAPER TEXTURE on page 50 and PAPER WEIGHT on page 51 for more information. • Verify that the print material is within the printer specifications. See “Using Print Materials” on page 115 for more information. • If the problem continues, call Lexmark Customer Support Center. p.190
Toner appears on the back of the printed page.Toner is on the transfer roll. To help prevent this, do not load print material that is smaller than the page size of the job to be printed. • Open and close the printer upper front door to run the printer through its setup cycle and clean the transfer roll. • Replace the fuser cleaner. The fuser cleaner and replacement instructions are included in the box when you purchase a new print cartridge. p.190
Toner fog or background shading appears on the page.• Check the print cartridge to make sure it is installed correctly. See “Installing the Print Cartridge” on page 5 for more information. • Change the print cartridge. See “Maintaining Your Printer” on page 193 for more information. • If the problem continues, change the charge roll. See “Ordering a Charge Roll Kit” on page 195 for more information. p.190
Entire page is white.• Make sure the packaging material is removed from the print cartridge. See “Removing Print Cartridge Packaging” on page 2. • Check the print cartridge to be sure it is installed correctly. See “Installing the Print Cartridge” on page 5 for more information. • Check the toner supply. p.190
Streaks appear on the page.• The toner may be low. Remove the cartridge. To utilize the remaining toner, shake the cartridge gently. Reinstall the same print cartridge. See “Installing the Print Cartridge” on page 5 for directions. • If you are using preprinted forms, make sure the ink can withstand temperatures of 200°C (392°F). • The printhead lens may need cleaning. See “Cleaning the Printhead Lens” on page 195 for directions. p.191
Printing is too dark.Change the Toner Darkness setting in the QUALITY MENU. See Toner Darkness on page 71 for more information. Note: Macintosh users should make sure the lines per inch (lpi) setting is not set too high in the software application. p.191
Characters have jagged or uneven edges.• Change the Print Resolution setting in the QUALITY MENU to 600 dpi. See Print Resolution on page 71 for more information. • Turn PQET in the QUALITY MENU to On. See PQET on page 72 for more information. • If you are using downloaded fonts, verify that the fonts are supported by the printer, the host computer, and the software application. p.191
Image quality is poor.Resolution was automatically reduced. Reduce the complexity of the print job or add additional printer memory. See Res Reduced on page 157 for more information. p.191
Part of all of the page is printed in black.• Check the print cartridge to see if it is installed correctly. See “Installing the Print Cartridge” on page 5 for more information. • If the charge roll has been replaced, verify that it has been installed correctly. Refer to the installation instructions that come with the charge roll kit. See “Ordering a Charge Roll Kit” on page 195 for more information. p.191
The job prints, but the left and top margins are incorrect.• Make sure the PAPER SIZE setting is set correctly in the PAPER MENU. See PAPER SIZE on page 45 for more information. • Make sure the margins are set correctly in the software application you are using. • Check the Print Area setting in the SETUP MENU. Set the value to Normal. See Print Area on page 76 for more information. p.191
Option does not operate correctly after it is installed or it quits working.• Turn the printer power Off (O), wait for about 10 seconds, and turn the printer power On (|). If this does not fix the problem, unplug the printer, and check the connection between the option and printer. • Print the menu settings page and check to see if the option is listed in the Installed Options list. If the option is not listed, reinstall it. See “Verifying the Installation of Options” on page 229 for more information. • Make sure the option is selected in the software application you are using. For Macintosh users: Make sure the printer is set up in CHOOSER. p.192
Option does not operate correctly after it is installed.Optional Drawer: Make sure the connection between the optional 500-sheet drawer and the printer is secure. See “Optional 500-Sheet Drawer” on page 223 for more information. Make sure the print material is loaded correctly. See “Loading Print Material” on page 124 for more information. p.192
Option does not operate correctly after it is installed.Flash Memory Option: Check to make sure the flash memory option is securely connected to the printer system board. See “Understanding Memory Options” on page 206 for more information. p.192
Option does not operate correctly after it is installed.Printer Memory Option: Check to make sure the printer memory option is securely connected to the printer system board. See “Understanding Memory Options” on page 206 for more information. p.192
Option does not operate correctly after it is installed.Hard Disk Option: Check to make sure the hard disk option is securely connected to the printer system board. See “Hard Disk Option” on page 212 for more information. p.192
Option does not operate correctly after it is installed.Hard Disk Adapter Card: Check to make sure the hard disk option is securely connected to the hard disk adapter card. Also check to make sure the hard disk adapter card is securely connected to the printer system board. See “Hard Disk Option” on page 212 for more information. p.192
Option does not operate correctly after it is installed.Internal Print Server Option: Check to make sure the optional internal print server (also called an internal network adapter or INA) is securely connected to the printer system board. See “Internal Print Server (Internal Network Adapter or INA)” on page 211 for more information. The connection to the network is made through the network cable. Check that you have the correct cable, that it is securely connected, and that the network software is correctly set up. See the documentation that comes with your optional internal print server for more information. p.192
Option does not operate correctly after it is installed.Tri-Port Interface Option: Check to make sure the Tri-Port Interface option card is securely connected to the printer system board. See “Tri-Port Interface Option Card” on page 212 for more information. For Macintosh users: Make sure the host computer is set to LocalTalk. If you are using a phone wire connection, a terminator plug must be used. p.192
Option does not operate correctly after it is installed. (continued)Infrared Adapter: If infrared communication stops or does not occur, check the following: • Communication distance: The distance between the two infrared ports should be 3 meters (10 ft.) or less. If communication does not occur between ports, move the ports closer together. • Make sure both ports are stable. Make sure the computer is on a level surface. • Make sure the angle of communication between the two infrared ports is within 15 degrees of either side of an imaginary line drawn between the two infrared ports. • Make sure there is no bright light, such as direct sunshine, interfering with communication. • Make sure no objects are placed between the two infrared ports. p.193
Option does not operate correctly after it is installed. (continued)Parallel/USB Interface Option: Check to make sure the parallel/USB interface option card is securely connected to the printer system board. See “Parallel/USB Interface Option Card” on page 215 for more information. p.193
Job did not print or incorrect characters printed.If you are using a Lexmark internal print server or external print server, verify that it is set up properly and the network cable is connected. Note: Refer to the documentation that comes with your print server for more information. For Novell users: • Make sure the netware.drv file is dated October 24, 1994 or later. • Make sure the NT (no tabs) flag is included in the capture statement. For Macintosh users: • The printer may need an optional internal print server to allow Macintosh connection. • Verify that the printer is set up correctly in CHOOSER. p.193
How do I get updated printer drivers or utilities?See “Introducing MarkVision” on page 25 for more information. p.194
How do I attach a serial cable to the printer?Your printer requires an optional adapter to allow serial attachment. The Tri-Port interface option card supports serial RS-232C/RS-422A. See “Tri-Port Interface Option Card” on page 212 for more information. p.194
Where are the printer escape codes listed?The CD that was shipped with your printer contains an Adobe Acrobat file with a complete list of Printer Command Language (PCL) escape codes. p.194

Ask about the Lexmark M412

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lexmark M412

Be the first to ask — other owners or our team will answer.

Original document

Lexmark M412 manual PDF

312 pages·3.8 MB·Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…