EN
Lexmark logo
Official user manual

Lexmark E310

154 pages·4.2 MB·Printer·PDF·ENDEFRITNLJA
Lexmark E310
Table of Contents 68 sections Table of Contents · Laser Notice · Safety Information · 1. General Information · … ShowHide
Table of Contentsp.3Laser Noticep.5Safety Informationp.151. General Informationp.21Optionsp.212. Diagnostic Informationp.23Startp.23Service Error Codesp.24User Error Message Tablep.28Power-On Self Test (POST)p.31Symptom Tablesp.32Service Checksp.34Cooling Fan Service Checkp.34Cover Open Switch Service Checkp.35Dead Machine Service Checkp.36Fuser Service Checkp.39Main Motor Service Checkp.43Operator Panel Service Checkp.45Operator Panel Button Service Checkp.46Paper Feed Service Checkp.46Print Quality Service Checkp.50Parallel Port Service Checkp.573. Diagnostic Aidsp.59Memory Testp.59Diagnostic Testp.59Print Quality Testp.60User Mode Print Testp.61Configuration Modep.61Hex Tracep.69Restoring Factory Defaultsp.70Engine Clean Cyclep.71Toggle Demo/Normal Modep.72Printer Operationp.72Paper Pathp.734. Repair Informationp.75Handling ESD-Sensitive Partsp.75Removal Proceduresp.76Screw Identification Tablep.76Coversp.76Frame Assemblyp.81Fuser Assemblyp.82HVPSp.84Interconnect Board (model E310)p.86Engine/LVPS Board (model E310)p.87Engine/LVPS Board (model E312)p.89Main Drive Assemblyp.91Pick Roll Assemblyp.92Printhead Assemblyp.94Transfer Rollp.955. Connector Locationsp.97Controller Board (model E310/E312)p.97Engine/LVPS Board (model E310)p.100Engine Board (model E312)p.105LVPS (model E312)p.110High Voltage Power Supply (model E310)p.112High Voltage Power Supply (model E312)p.114Interconnect Board (model E310)p.1176. Parts Catalogp.121Assembly 1: Coversp.122Assembly 2: Framep.126Assembly 3: Fuserp.130Assembly 4: Main Drivep.134Assembly 5: Paper Feedp.136Assembly 6: Electronics (model E310)p.140Assembly 6: Electronics (model E312)p.144Assembly 7: Optionsp.146Assembly 8: Miscellaneousp.147Indexp.149
Page 1 of the Lexmark E310 user manual — Optra TM E310/E312
Page 1 · click to enlarge
Page 1

Optra TM E310/E312

  • Table of Contents
  • Start Diagnostics
  • Safety and Notices
  • Trademarks
  • Index

Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.

Page 2 of the Lexmark E310 user manual
Page 2 · click to enlarge
Page 2
EditionMay 2001

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.

A form for reader’s comments is provided at the back of this publication. If the form has been removed, comments may be addressed to Lexmark International, Inc., Department D22A/032-2, 740 West New Circle Road, Lexington, Kentucky 40550, U.S.A. Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. You can purchase additional copies of publications related to this product by calling 1-800-553-9727. In other countries, contact your point of purchase.

Lexmark and Optra are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.

Other trademarks are the property of their respective owners.

© Copyright Lexmark International, Inc. 2000, 2001. All rights reserved.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS This software and documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 and in applicable FAR provisions: Lexmark International, Inc., Lexington, KY 40550.

Page 3 of the Lexmark E310 user manual — Table of Contents
Page 3 · Contents
Contents

Contents

Table of Contentsp.3Laser Noticep.5Safety Informationp.151. General Informationp.21Optionsp.212. Diagnostic Informationp.23Startp.23Service Error Codesp.24User Error Message Tablep.28Power-On Self Test (POST)p.31Symptom Tablesp.32Service Checksp.34Cooling Fan Service Checkp.34Cover Open Switch Service Checkp.35Dead Machine Service Checkp.36Fuser Service Checkp.39Main Motor Service Checkp.43Operator Panel Service Checkp.45Operator Panel Button Service Checkp.46Paper Feed Service Checkp.46Print Quality Service Checkp.50Parallel Port Service Checkp.573. Diagnostic Aidsp.59Memory Testp.59Diagnostic Testp.59Print Quality Testp.60User Mode Print Testp.61Configuration Modep.61Hex Tracep.69Restoring Factory Defaultsp.70Engine Clean Cyclep.71Toggle Demo/Normal Modep.72Printer Operationp.72Paper Pathp.734. Repair Informationp.75Handling ESD-Sensitive Partsp.75Removal Proceduresp.76Screw Identification Tablep.76Coversp.76Frame Assemblyp.81Fuser Assemblyp.82HVPSp.84Interconnect Board (model E310)p.86Engine/LVPS Board (model E310)p.87Engine/LVPS Board (model E312)p.89Main Drive Assemblyp.91Pick Roll Assemblyp.92Printhead Assemblyp.94Transfer Rollp.955. Connector Locationsp.97Controller Board (model E310/E312)p.97Engine/LVPS Board (model E310)p.100Engine Board (model E312)p.105LVPS (model E312)p.110High Voltage Power Supply (model E310)p.112High Voltage Power Supply (model E312)p.114Interconnect Board (model E310)p.1176. Parts Catalogp.121Assembly 1: Coversp.122Assembly 2: Framep.126Assembly 3: Fuserp.130Assembly 4: Main Drivep.134Assembly 5: Paper Feedp.136Assembly 6: Electronics (model E310)p.140Assembly 6: Electronics (model E312)p.144Assembly 7: Optionsp.146Assembly 8: Miscellaneousp.147Indexp.149
Page 5 of the Lexmark E310 user manual — Laser Notice
Page 5 · click to enlarge
Page 5

Notices and Safety Information

Laser Notice

The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 825.

Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 5 milliwatt gallium arsenide laser operating in the wavelength region of 770-795 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.

Page 6 of the Lexmark E310 user manual — Laser Advisory Label
Page 6 · click to enlarge
Page 6

Laser Advisory Label

Lexmark E310 — Laser Advisory Label diagram (page 6)
Fig. 1 · Laser Advisory Label
Page 7 of the Lexmark E310 user manual — Class 1 Laser Statement Label
Page 7 · click to enlarge
Page 7

Class 1 Laser Statement Label

Lexmark E310 — Class 1 Laser Statement Label diagram (page 7)
Fig. 2 · Class 1 Laser Statement Label
Page 8 of the Lexmark E310 user manual — Avis relatif à l’utilisation de laser
Page 8 · click to enlarge
Page 8

Laser

Der Drucker erfüllt gemäß amtlicher Bestätigung der USA die Anforderungen der Bestimmung DHHS (Department of Health and Human Services) 21 CFR Teil J für Laserprodukte der Klasse I (1). In anderen Ländern gilt der Drucker als Laserprodukt der Klasse I, der die Anforderungen der IEC (International Electrotechnical Commission) 825 gemäß amtlicher Bestätigung erfüllt.

Laserprodukte der Klasse I gelten als unschädlich. Im Inneren des Druckers befindet sich ein Laser der Klasse IIIb (3b), bei dem es sich um einen Galliumarsenlaser mit 5 Milliwatt handelt, der Wellen der Länge 770-795 Nanometer ausstrahlt. Das Lasersystem und der Drucker sind so konzipiert, daß im Normalbetrieb, bei der Wartung durch den Benutzer oder bei ordnungsgemäßer Wartung durch den Kundendienst Laserbestrahlung, die die Klasse I übersteigen würde, Menschen keinesfalls erreicht.

Avis relatif à l’utilisation de laser

Pour les Etats-Unis : cette imprimante est certifiée conforme aux provisions DHHS 21 CFR alinéa J concernant les produits laser de Classe I (1). Pour les autres pays : cette imprimante répond aux normes IEC 825 relatives aux produits laser de Classe I.

Les produits laser de Classe I sont considérés comme des produits non dangereux. Cette imprimante est équipée d’un laser de Classe IIIb (3b) (arséniure de gallium d’une puissance nominale de 5 milliwatts) émettant sur des longueurs d’onde comprises entre 770 et 795 nanomètres. L’imprimante et son système laser sont conçus pour impossible, dans des conditions normales d’utilisation, d’entretien par l’utilisateur ou de révision, l’exposition à des rayonnements laser supérieurs à des rayonnements de Classe I .

Page 9 of the Lexmark E310 user manual — Avisos sobre el láser
Page 9 · click to enlarge
Page 9

Avvertenze sui prodotti laser

Questa stampante è certificata negli Stati Uniti per essere conforme ai requisiti del DHHS 21 CFR Sottocapitolo J per i prodotti laser di classe 1 ed è certificata negli altri Paesi come prodotto laser di classe 1 conforme ai requisiti della norma CEI 825.

I prodotti laser di classe non sono considerati pericolosi. La stampante contiene al suo interno un laser di classe IIIb (3b) all’arseniuro di gallio della potenza di 5mW che opera sulla lunghezza d’onda compresa tra 770 e 795 nanometri. Il sistema laser e la stampante sono stati progettati in modo tale che le persone a contatto con la stampante, durante il normale funzionamento, le operazioni di servizio o quelle di assistenza tecnica, non ricevano radiazioni laser superiori al livello della classe 1..

Avisos sobre el láser

Se certifica que, en los EE.UU., esta impresora cumple los requisitos para los productos láser de Clase I (1) establecidos en el subcapítulo J de la norma CFR 21 del DHHS (Departamento de Sanidad y Servicios) y, en los demás países, reúne todas las condiciones expuestas en la norma IEC 825 para productos láser de Clase I (1).

Los productos láser de Clase I no se consideran peligrosos. La impresora contiene en su interior un láser de Clase IIIb (3b) de arseniuro de galio de funcionamiento nominal a 5 milivatios en una longitud de onda de 770 a 795 nanómetros. El sistema láser y la impresora están diseñados de forma que ninguna persona pueda verse afectada por ningún tipo de radiación láser superior al nivel de la Clase I durante su uso normal, el mantenimiento realizado por el usuario o cualquier otra situación de servicio técnico.

Page 10 of the Lexmark E310 user manual — Laserinformatie
Page 10 · click to enlarge
Page 10

Declaração sobre Laser

A impressora está certificada nos E.U.A. em conformidade com os requisitos da regulamentação DHHS 21 CFR Subcapítulo J para a Classe I (1) de produtos laser. Em outros locais, está certificada como um produto laser da Classe I, em conformidade com os requisitos da norma IEC 825.

Os produtos laser da Classe I não são considerados perigosos. Internamente, a impressora contém um produto laser da Classe IIIb (3b), designado laser de arseneto de potássio, de 5 milliwatts ,operando numa faixa de comprimento de onda entre 770 e 795 nanómetros. O sistema e a impressora laser foram concebidos de forma a nunca existir qualquer possiblidade de acesso humano a radiação laser superior a um nível de Classe I durante a operação normal, a manutenção feita pelo utilizador ou condições de assistência prescritas.

Laserinformatie

De printer voldoet aan de eisen die gesteld worden aan een laserprodukt van klasse I. Voor de Verenigde Staten zijn deze eisen vastgelegd in DHHS 21 CFR Subchapter J, voor andere landen in IEC 825.

Laserprodukten van klasse I worden niet als ongevaarlijk aangemerkt. De printer is voorzien van een laser van klasse IIIb (3b), dat wil zeggen een gallium arsenide-laser van 5 milliwatt met een golflengte van 770-795 nanometer. Het lasergedeelte en de printer zijn zo ontworpen dat bij normaal gebruik, bij onderhoud of reparatie conform de voorschriften, nooit blootstelling mogelijk is aan laserstraling boven een niveau zoals voorgeschreven is voor klasse 1.

Page 12 of the Lexmark E310 user manual — Laser-melding
Page 12 · click to enlarge
Page 12

Laser-notis

Denna skrivare är i USA certifierad att motsvara kraven i DHHS 21 CFR, underparagraf J för laserprodukter av Klass I (1). I andra länder uppfyller skrivaren kraven för laserprodukter av Klass I enligt kraven i IEC 825.

Laserprodukter i Klass I anses ej hälsovådliga. Skrivaren har en inbyggd laser av Klass IIIb (3b) som består av en laserenhet av gallium-arsenid på 5 milliwatt som arbetar i våglängdsområdet 770- 795 nanometer. Lasersystemet och skrivaren är utformade så att det aldrig finns risk för att någon person utsätts för laserstrålning över Klass I-nivå vid normal användning, underhåll som utförs av användaren eller annan föreskriven serviceåtgärd.

Laser-melding

Skriveren er godkjent i USA etter kravene i DHHS 21 CFR, underkapittel J, for klasse I (1) laserprodukter, og er i andre land godkjent som et Klasse I-laserprodukt i samsvar med kravene i IEC 825.

Klasse I-laserprodukter er ikke å betrakte som farlige. Skriveren inneholder internt en klasse IIIb (3b)-laser, som består av en gallium-arsenlaserenhet som avgir stråling i bølgelengdeområdet 770-795 nanometer. Lasersystemet og skriveren er utformet slik at personer aldri utsettes for laserstråling ut over klasse I-nivå under vanlig bruk, vedlikehold som utføres av brukeren, eller foreskrevne serviceoperasjoner.

Page 14 of the Lexmark E310 user manual — Chinese Laser Notice
Page 14 · click to enlarge
Page 14

Japanese Laser Notice

Lexmark E310 — Japanese Laser Notice diagram (page 14)
Fig. 3 · Japanese Laser Notice

Chinese Laser Notice

Lexmark E310 — Chinese Laser Notice diagram (page 14)
Fig. 4 · Chinese Laser Notice
Page 15 of the Lexmark E310 user manual — Safety Information
Page 15 · click to enlarge
Page 15

Korean Laser Notice

Lexmark E310 — Korean Laser Notice diagram (page 15)
Fig. 5 · Korean Laser Notice
Lexmark E310 — Korean Laser Notice diagram (page 15)
Fig. 6 · Korean Laser Notice

Safety Information

  • This product is designed, tested and approved to meet strict global safety standards with the use of specific Lexmark components. The safety features of some parts may not always be obvious. Lexmark is not responsible for the use of other replacement parts.
  • The maintenance information for this product has been prepared for use by a professional service person and is not intended to be used by others.
  • There may be an increased risk of electric shock and personal injury during disassembly and servicing of this product. Professional service personnel should understand this and take necessary precautions.
Page 16 of the Lexmark E310 user manual — Norme di sicurezza
Page 16 · click to enlarge
Page 16

Consignes de Sécurité

  • Ce produit a été conçu, testé et approuvé pour respecter les normes strictes de sécurité globale lors de l'utilisation de composants Lexmark spécifiques. Les caractéristiques de sécurité de certains éléments ne sont pas toujours évidentes. Lexmark ne peut être tenu responsable de l'utilisation d'autres pièces de rechange.
  • Les consignes d'entretien et de réparation de ce produit s'adressent uniquement à un personnel de maintenance qualifié.
  • Le démontage et l'entretien de ce produit pouvant présenter certains risques électriques, le personnel d'entretien qualifié devra prendre toutes les précautions nécessaires.

Norme di sicurezza

  • Il prodotto è stato progettato, testato e approvato in conformità a severi standard di sicurezza e per l’utilizzo con componenti Lexmark specifici. Le caratteristiche di sicurezza di alcune parti non sempre sono di immediata comprensione. Lexmark non è responsabile per l’utilizzo di parti di ricambio di altri produttori.
  • Le informazioni riguardanti la manutenzione di questo prodotto sono indirizzate soltanto al personale di assistenza autorizzato.
  • Durante lo smontaggio e la manutenzione di questo prodotto, il rischio di subire scosse elettriche e danni alla persona è più elevato. Il personale di assistenza autorizzato, deve, quindi, adottare le precauzioni necessarie.
Page 19 of the Lexmark E310 user manual — Korean Safety Information
Page 19 · click to enlarge
Page 19

Chinese Safety Information

Lexmark E310 — Chinese Safety Information diagram (page 19)
Fig. 7 · Chinese Safety Information

Korean Safety Information

Lexmark E310 — Korean Safety Information diagram (page 19)
Fig. 8 · Korean Safety Information
Page 20 of the Lexmark E310 user manual — Safety Information
Page 20 · click to enlarge
Page 20
Page 20 of the Lexmark E310 user manual — Safety Information
Page 21 of the Lexmark E310 user manual — Options
Page 21 · click to enlarge
Page 21

1. General Information

This printer is a letter-quality laser page printer designed to attach to an IBM Personal Computer or other computers compatible with the IBM Personal Computer (with 386 processor or higher) and Macintosh Computers via the USB connection.

MT/Model 4044-001 4044-201 4044-2L1 4044-2L2

Speed 8 pages per minute

10 pages per minute

10 pages per minute

10 pages per minute

2MB 4MB 4MB 2MB

Emulations PSLII, PCL6, PPDS

PSLII, PCL6, PPDS

PSLII, PCL6, PPDS

PSLII, PCL6, PPDS

Resolution True 600dpi/Image Quality 1200dpi

6k pages 6k pages 1.5k pages 1.5k pages

Options

The following options are available. Some options are not available in every country. Contact your point of purchase for options available in your country.

Memory options of 8MB, 16MB, 32MB and 64MB Flash memory options of 1MB, 2MB and 4MB

Show 12 more labels / short text on this page
Product Name · Optra E310 · Optra E312 · Optra E312L · Optra E312L · Base Memory · Connectivity Parallel/ USB · Parallel/ USB · Parallel/ USB · Parallel/ USB · Starter Toner Cartridge · General Information 1-1
Page 22 of the Lexmark E310 user manual — Acronyms
Page 22 · click to enlarge
Page 22

Acronyms

CSU Customer Setup DRAM Dynamic Random Access Memory EP Electrophotographic Process EPROM Erasable, Programmable Read-Only Memory ESD Electrostatic Discharge FRU Field Replaceable Unit HVPS High Voltage Power Supply LASER Light Amplification by Stimulated Emission of Radiation LCD Liquid Crystal Display LED Light-Emitting Diode LVPS Low Voltage Power Supply MROM Masked Read Only Memory NVRAM Nonvolatile Random Access Memory OEM Original Equipment Manufacturer PC Photoconductor POST Power-On Self Test ROM Read Only Memory SIMM Single In-Line Memory Module SRAM Static Random Access Memory UPR Used Parts Return USB Universal Serial Bus V ac Volts alternating current V dc Volts direct current

Page 23 of the Lexmark E310 user manual — Start
Page 23 · click to enlarge
Page 23

2. Diagnostic Information

Start

CAUTION: NEVER manually actuate or disable the top cover interlock switch and the printhead shutter actuator at the same time. To perform some of the service checks and tests, such as troubleshooting paper feed problems, you need to actuate the top cover interlock switch with the covers opened or removed and power applied to the machine. It is important for personal safety that you DO NOT, FOR ANY REASON, disable the printhead shutter actuator when power is on.

Remove power from the printer before you connect or disconnect any cable or electronic board or assembly for personal safety and to prevent damage to the printer.

Use the service error code, user error message, symptom table, service checks, and diagnostic aids in this chapter to determine the corrective action necessary to repair a malfunctioning printer.

The lights on the operator panel can indicate either a user error message or service error message. When a service error occurs, the printer stops printing and all operator panel LEDs blink in a continuous pattern, indicating a service error, until the printer is powered off. If all operator panel LEDs are blinking, go to the “Service Error Codes” on page 2-2.

When a user error message occurs, one or two operator panel LEDs are on solid or blinking. Go to the “User Error Message Table” on page 2-6.

If your machine does not have a service error code and does not complete POST, go to the “POST Symptom Table” on page 2-10. If your machine completes POST without an error, and you have a symptom, go to the “Base Printer Symptom Table” on page 2-10. Locate your symptom and take the appropriate action.

If a service error code appears while you are working on the machine, go to the “Service Error Codes” on page 2-2 and take the indicated action for that error.

Diagnostic Information 2-1

Page 24 of the Lexmark E310 user manual — Primary Service Error Codes
Page 24 · click to enlarge
Page 24

Service Error Codes

Primary Service Error Codes

When a service error occurs the printer stops printing and all operator panel LEDs blink in a continuous pattern, indicating a service error, until the printer is powered off.

Press and release the operator panel button to display the service error code. Locate the blinking LEDs in the following table and take the indicated action.

Blinking Operator Panel LED Action

Software Service Error Code Run the Printer Diagnostic Test to diagnose between the ROM SIMM and the controller board. If no other error code displays after the test completes, replace the controller board.

Fuser Failure Error Press and release the operator panel button to view the secondary service error code. Go to “Secondary Service Error Codes” on page 2-5.

Laser Diode Failure Inspect the printhead cable and replace as necessary. Replace the printhead assembly. If this does not correct the problem, replace the engine/LVPS board.

Page 25 of the Lexmark E310 user manual — Service Error Codes
Page 25 · click to enlarge
Page 25
Lexmark E310 — Service Error Codes diagram (page 25)
Fig. 9 · Service Error Codes

Mirror Motor Failure Inspect the printhead cable and replace as necessary. Replace the printhead assembly. If this does not correct the problem, replace the engine/LVPS board.

Optional Memory Error Replace the optional memory SIMM. If this does not correct the problem, replace the controller board.

ROM Checksum Error Replace the ROM SIMM. If this does not correct the problem, replace the controller board.

Diagnostic Information 2-3

Page 26 of the Lexmark E310 user manual — Service Error Codes
Page 26 · click to enlarge
Page 26
Lexmark E310 — Service Error Codes diagram (page 26)
Fig. 10 · Service Error Codes

Flash Memory Failure Error Replace the ROM SIMM w/Flash. If this does not correct the problem, replace the controller board.

Font Checksum Failure Error Replace the ROM SIMM. If this does not correct the problem, replace the controller board.

Page 27 of the Lexmark E310 user manual — Secondary Service Error Codes
Page 27 · click to enlarge
Page 27

Secondary Service Error Codes

For some service error codes, a second service error code is used to further describe the error. When a service error occurs, pressing the operator panel button after viewing the primary service error code displays the secondary service error code. The following table contains the secondary service error codes.

Blinking Operator Panel LED Action

Fuser Failure - Over Temperature Go to the “Hot Fuser Service Check” on page 2-21.

Fuser Failure - Under Temperature

Go to the “Cold Fuser Service Check” on page 2-17.

Fuser Failure - Thermistor Open Go to the “Fuser Service Check” on page 2-17.

Diagnostic Information 2-5

Page 28 of the Lexmark E310 user manual — Primary User Error Message Table
Page 28 · click to enlarge
Page 28

User Error Message Table

Primary User Error Message Table

When a user error message occurs the printer stops printing and one or two operator panel LEDs are on solid or blinking until the printer is powered off. Locate the printer’s LED Status in the following table and take the indicated action.

User Error Message LED Status Action

Paper Jam Paper Jam on solid Open cover and clear any paper jams. Close the top cover. If the error message is still present, go to the“Paper Feed Service Check” on page 2-24.

Load Manual Paper/ Envelope

Load Paper blinks and Press Button on solid

Load media into the manual slot and push the operator panel button to resume printing one sheet or do an operator panel reset by pressing and holding the operator panel button for more than three seconds.

Load Paper on solid and Press Button on solid

Load media in the appropriate paper tray and push the operator panel button to resume printing or do an operator panel reset by pressing and holding the operator panel button for more than three seconds.

Top Cover Open Error on solid Close the top cover. If the error LED remains on solid and POST does not continue, go to the “Cover Open Switch Service Check” on page 2-13.

Load Paper/Load Envelope

Page 29 of the Lexmark E310 user manual — User Error Message Table
Page 29 · click to enlarge
Page 29

User Error Message LED Status Action

Memory Full/Complex Page/Resolution Reduction Warning/ Font Error/ Resource Save Off Deficient Memory

Error on solid and Press Button on solid

The printer memory is full or the page is too complex to print. The printer is forced to reduce the resolution of a formatted page to 300 dpi before printing, or the printer is unable to maintain the required data transfer rate. Go to the “Secondary User Error Message Table” on page 2-8.

Flash Memory Full Error blinks and Press Button on solid

This condition only occurs when the Flash memory is full.

Diagnostic Information 2-7

Page 30 of the Lexmark E310 user manual — Secondary User Error Message Table
Page 30 · click to enlarge
Page 30

Secondary User Error Message Table

Press and release the operator panel button two times to display the user secondary error LED status. Each press and release action must be performed within a half second. Locate the printer’s LED status in the following table and take the indicated action.

User Error Message LED Status Action

Complex Page Ready, Error, and Press Button on solid

Switch the printing mode to a different printing mode using the Lexmark driver for Windows, or push the operator panel button to resume printing, or do an operator panel reset by pressing and holding the operator panel button for more than three seconds.

Memory Full Ready, Data, Error, and Press Button on solid

Change the printing mode to Quick Print Plus or reduce the complexity of the job or the resolution, or push the operator panel button to resume printing, or do an operator panel reset by pressing and holding the operator panel button for more than three seconds.

Resolution Reduction Ready, Data blinking and the Error, Press Button on solid

Switch from the GL/2 or raster mode to Quick Print Plus mode using the Lexmark driver for Windows, or press the operator panel button to resume printing, or do an operator panel reset by pressing and holding the operator button for more than three seconds.

Page 31 of the Lexmark E310 user manual — Power-On Self Test (POST)
Page 31 · click to enlarge
Page 31

User Error Message LED Status Action

Font Error Data blinking and Error, Press Button on solid

The print command is requesting a font that is not present or installed. The user must select a different font or try turning the Best Fit setting on and retry the print command.

Resource Save Off Deficient Memory

Ready blinking and Error, Press Button on solid

The printer lacks sufficient memory to enable Resource Save. It is recommended that the user install additional memory or set each link buffer to the Auto value.

Power-On Self Test (POST)

When you turn the printer On, it performs a Power-On Self Test. Check for correct POST functioning of the base printer by observing the following:

1. All LEDs turn on solid. 2. All LEDs turn off. 3. The cooling fan and fuser lamp turn on. Note: The fuser lamp turns off once the thermistor reaches operating temperature. As the temperature drops, the lamp turns back on automatically.
4. The LEDs begin to turn on then off sequentially. 5. Once the fuser has reached operating temperature, the main motor turns on and the pick roller shaft assembly rotates to home position. 6. The Ready LED turns on solid while the Data LED blinks. 7. The engine/LVPS board checks the status of the input and exit paper feed sensors. 8. The main motor turns off. 9. The Data LED turns off.

Diagnostic Information 2-9

Page 32 of the Lexmark E310 user manual — Base Printer Symptom Table
Page 32 · click to enlarge
Page 32

Symptom Tables

POST Symptom Table

The main motor, cooling fan and fuser do not come on.

Go to “Cover Open Switch Service Check” on page 2-13.

POST completes except one or more LEDs do not come on.

Go to the“Operator Panel Service Check” on page 2-23.

None of the LEDs come on. Go to the “Operator Panel Service Check” on page 2-23.

Main motor does not come on. Go to the “Main Motor Service Check” on page 2-21.

Fan does not come on. Go to the “Cooling Fan Service Check” on page 2-12.

Fuser lamp does not come on. Go to the “Cold Fuser Service Check” on page 2-17.

Fuser lamp never turns off. Go to the “Hot Fuser Service Check” on page 2-21.

The paper feed picks and tries to feed paper.

Go to the “Paper Feed Service Check” on page 2-24.

Base Printer Symptom Table

Dead Machine (no power) Go to the “Dead Machine Service Check” on page 2-14.

Fan noisy or not working Go to the “Cooling Fan Service Check” on page 2-12.

Fuser parts melted Go to the “Hot Fuser Service Check” on page 2-21.

Fuser lamp doesn’t light Go to “Cold Fuser Service Check” on page 2-17.

Toner not fused to the paper Go to “Cold Fuser Service Check” on page 2-17.

Symptom Action · Symptom Action

Page 33 of the Lexmark E310 user manual — Symptom Tables
Page 33 · click to enlarge
Page 33

Blank page Go to “Blank page” on page 2-28.

Black page Go to “Black page” on page 2-29.

Heavy background Go to “Heavy background” on page 2-30.

Light print Go to “Light print” on page 2-33.

White or black lines or bands Go to “White or black lines or bands” on page 2-34.

Toner on back of page Go to “Toner on back of page” on page 2-34.

Incorrect characters print Go to “Incorrect characters print” on page 2-34.

Paper jams Go to “Paper Feed Service Check” on page 2-24.

Main Motor noisy or does not move

Go to “Main Motor Service Check” on page 2-21.

Paper never picks Go to “Paper never picks” on page 2-27.

Paper feeds continuously Go to “Paper picks during POST and/or continuously” on page 2-25.

Paper skew Go to “Paper Feed Service Check” on page 2-24.

Printer not communicating with host

Go to “Parallel Port Service Check” on page 2-35.

Paper wrinkled or bent Go to “Paper "trees", wrinkles, stacks poorly or curls” on page 2-28.

Top cover will not close Go to “Cover Open Switch Service Check” on page 2-13.

Operator panel button does not respond

Go to “Operator Panel Button Service Check” on page 2-24.

Operator panel LEDs do not light or very dim

Go to “Operator Panel Service Check” on page 2-23.

Symptom Action · Diagnostic Information 2-11

Page 34 of the Lexmark E310 user manual — Cooling Fan Service Check
Page 34 · click to enlarge
Page 34

Service Checks

Cooling Fan Service Check

Model E310 Interconnect Board Cooling Fan

Make sure motor cable is properly seated in location CN408 on the interconnect board. Disconnect the cable and check connector-pin CN408-3 for +24 V dc. If the voltage is not present, replace the interconnect board. If the voltage is present, replace the cooling fan.

Model E312 Engine Board Cooling Fan

Make sure motor cable is properly seated in location CN3 on the engine board. Disconnect the cable and check connector-pin CN3-1 for +24 V dc. If the voltage is not present, replace the engine board. If the voltage is present, replace the cooling fan.

FRU Action · FRU Action

Page 35 of the Lexmark E310 user manual — Cover Open Switch Service Check
Page 35 · click to enlarge
Page 35

Cover Open Switch Service Check

Models E310 & E312 Cover Open Switch

Make sure the cover open switch cable is properly seated in CN2 of the HVPS. Disconnect the cable and check the switch for continuity. Push the cover open switch lever down to engage the switch and close the circuit. If the circuit does not close, replace the switch.

Model E310 HVPS Engine/LVPS Board

Measure the voltage at CN2-3 of the HVPS. It measures +24 V dc. If voltage is present at CN2-3, check for continuity between CN2-1 and CN1-2. If continuity does not exist, replace the HVPS. If continuity does exist, check the HVPS to engine/ LVPS board cable for continuity. Replace if defective. If voltage is not present at CN2-3, check the voltage at CN1-1. It measures +24 V dc. If it does, replace the HVPS. If it does not, check the voltage at CN2-2 of the engine/LVPS board. It measures +24 V dc. If it does, replace the HVPS to engine/LVPS board cable.

FRU Action · Diagnostic Information 2-13

Page 36 of the Lexmark E310 user manual — Dead Machine Service Check
Page 36 · click to enlarge
Page 36

Measure the voltages at CN2 of the HVPS. CN2-3 measures +5 V dc and CN2-4 measures +24 V dc. If the correct voltage is present, check the continuity between the following connector locations:

CN2-3 - CN1-17 CN2-3 - CN1-19 CN2-4 - CN1-2 CN2-4 - CN1-4

If any location does not measure continuity, replace the HVPS.

Model E312 HVPS to Engine Board Cable

Replace the cable if it does not measure continuity.

Go to the “Engine Board (model E312)” on page -9. Measure the voltages on CN11. If any voltages are incorrect, replace the engine board.

Dead Machine Service Check

100 V ac - 127 V ac for the low voltage model printer

200 V ac - 240 V ac for the high voltage model printer

Model E310 & E312 LVPS Fuse

Check the fuse on the LVPS for continuity. Replace with the appropriate fuse if blown. If a fuse blows again after being replaced, install a new fuse and go to “Engine/ LVPS Board (model E310)” on page 5-4 and check the engine/ LVPS board output.

Show 4 more labels / short text on this page
FRU Action · Model E312 HVPS · E312 Engine Board · FRU Action
Page 37 of the Lexmark E310 user manual — CN401/CN402/CN403/CN404/ CN405/CN407/CN408
Page 37 · click to enlarge
Page 37

Model E310 Engine/LVPS Board Power Switch

Disconnect the cables from CN2 and CN5 and leave the cables connected to the power switch attached. With the printer positioned on its left side and the engine/LVPS board positioned on a flat surface, turn the power switch on and check the AC line voltage at connector CN201. If no voltage is present, replace the power switch. If line voltage is present, measure the voltages at connectors CN2 and CN5. Go to the“Engine/LVPS Board (model E310)” on page 5-4 and check for correct voltage measurements. Replace the engine/LVPS board if any of the voltage measurements are incorrect.

Model E310 LVPS to Interconnect Board Cable

Check the continuity of the LVPS to interconnect board cable. Replace the cable if it does not measure continuity.

Model E310 Interconnect Board

Reconnect the LVPS to the interconnect board cable. Go to “Interconnect Board (model E310)” on page 5-21 and measure voltages on the following connectors on the interconnect board:

CN401/CN402/CN403/CN404/ CN405/CN407/CN408

If any of the measured voltages are incorrect, replace the interconnect board.

Model E312 Power Switch

Place the printer on its rear side. Position the LVPS board on a flat surface with all the cables connected. Turn the printer power switch to the on position. Check the AC line voltage at power switch connector CN501. If no voltage is present, replace the power switch

FRU Action · Diagnostic Information 2-15

Page 38 of the Lexmark E310 user manual — Dead Machine Service Check
Page 38 · click to enlarge
Page 38

Model E312 LVPS Board

Disconnect the LVPS cable from connector CN7 on the engine board. Go to the “LVPS (model E312)” on page -14. Check the voltage measurements at connector CN503. If any voltage measurements are incorrect, replace the LVPS.

Model E312 Engine Board

Reconnect the LVPS cable to connector CN7 on the engine board. Disconnect all other cables from the engine board. Go to the “Engine Board (model E312)” on page -9. Check the voltage measurements at each connector. If any voltages are incorrect, replace the engine board. If all voltages are correct, reconnect all the cables to the engine board one at a time. Check the voltage meausrements on the engine board each time you connect a cable. If a voltage measurement is incorrect after connecting one of the cables, replace the FRU that you connected.

FRU Action

Page 39 of the Lexmark E310 user manual — Cold Fuser Service Check
Page 39 · click to enlarge
Page 39

Fuser Service Check

Cold Fuser Service Check

When toner is partially fused to the paper, it is usually caused by low fuser temperature.

Avoid handling the lamp as much as possible as it is easily broken. Be careful not to touch the glass housing with bare hands as skin contains acids that can weaken the glass.

The line voltage to the printer must be within the following limits:

100 V ac - 127 V ac for the low voltage model printer

200 V ac - 240 V ac for the high voltage model printer

Turn the printer off and wait a few minutes for the fuser lamp to cool. Turn the machine on and observe the lamp turning on during POST. You can see the lamp with the left side cover and fuser wire cover removed.

Diagnostic Information 2-17

Page 40 of the Lexmark E310 user manual — The fuser lamp does light
Page 40 · click to enlarge
Page 40

The fuser lamp does light

If the fuser lamp comes on and a fuser failure LED error code displays, be sure the thermistor is contacting the hot roll and the thermistor cable is firmly seated in connector CN1 on the LVPS board. Check for excessive toner buildup on the surface of the thermistor. Clean or replace as necessary. Turn the printer off and disconnect the thermistor cable from CN1 on the LVPS board. Measure the resistance of the thermistor between CN1-1 and CN1-2. The resistance measures approximately 225K ohms when cool. Replace the thermistor as necessary.

If the fuser lamp comes on and a fuser failure LED error code displays, be sure the thermistor is contacting the hot roll and the thermistor cable is firmly seated in connector CN10 on the engine board. Check for excessive toner buildup on the surface of the thermistor. Clean or replace as necessary. Turn the printer off and disconnect the thermistor cable from CN10 on the engine board. Measure the resistance of the thermistor between CN10-1 and CN10-3. The resistance measures approximately 225K ohms when cool. Replace the thermistor as necessary.

Models E310 & E312 Fuser Lamp

Make sure the correct voltage lamp is installed. The voltage rating is stamped on one of the lamp contacts.

FRU Action · Model 310 Thermistor · Model 312 Thermistor

Page 41 of the Lexmark E310 user manual — The fuser lamp does not light
Page 41 · click to enlarge
Page 41

The fuser lamp does not light

Model E310 Fuser Lamp Lamp Cable Thermistor LVPS

Turn the printer off and disconnect the fuser lamp wires from the fuser. Check for continuity across the fuser lamp wire contacts. If there is continuity, go to step 1: Continuity. If there is no continuity, go to step 2: No Continuity.

1. Continuity

Measure the voltage at connector CN202 on the LVPS. It should match the line voltage. If it does not, replace the LVPS. If line voltage is present, check the fuser lamp cable for continuity. Replace if defective.Make sure the fuser thermistor is correctly connected to CN1 on the LVPS. If the problem persists, disconnect the thermistor cable from CN1 on the LVPS board and measure the voltage between CN1-1 and ground. The voltage measures approximately 3.9 V dc. If the voltage is incorrect, replace the LVPS. If correct, replace the thermistor.

2. No Continuity

Check the thermal fuse for continuity. If incorrect, replace the thermal fuse. If correct, replace the lamp.

FRU Action · Diagnostic Information 2-19

Page 42 of the Lexmark E310 user manual — Fuser Service Check
Page 42 · click to enlarge
Page 42

Model E312 Fuser Lamp Lamp Cable Thermistor LVPS

Turn the printer off and disconnect the fuser lamp wires from the fuser. Check for continuity across the fuser lamp wire contacts. If there is continuity, go to step 1: Continuity. If there is no continuity, go to step 2: No Continuity.

1. Continuity

Measure the voltage at connector CN502 on the LVPS. It should match the line voltage. If it does not, replace the LVPS. If line voltage is present, check the fuser lamp cable for continuity. Replace if defective.Make sure the fuser thermistor is correctly connected to CN10 on the engine board. If the problem persists, disconnect the thermistor cable from CN1o on the engine board and measure the voltage between CN10-1 and ground. The voltage measures approximately 3.9 V dc. If the voltage is incorrect, replace the engine board. If correct, replace the thermistor.

2. No Continuity

Check the thermal fuse for continuity. If incorrect, replace the thermal fuse. If correct, replace the lamp.

FRU Action

Page 43 of the Lexmark E310 user manual — Main Motor Service Check
Page 43 · click to enlarge
Page 43

Hot Fuser Service Check

Model E310 Fuser Thermistor

Disconnect the thermistor cable from the LVPS. Measure the resistance across CN1-1 and CN1-2 of the thermistor cable. Replace the thermistor if the resistance is lower than 1k ohm or shorted.

Model E312 Fuser Thermistor

Disconnect the thermistor cable from the engine board. Measure the resistance across CN10-1 and CN10-3 of the thermistor cable. Replace the thermistor if the resistance is lower than 1k ohm or shorted.

Models E310 & E312 Fuser Lamp

Make sure the correct voltage fuser lamp is installed. Replace if necessary.

Main Motor Service Check

Model E310 Interconnect Board Main Motor Main Motor Cable

Check the interconnect board for the following voltages:

CN405-3 +24 V dc CN405-4 +24 V dc

If these voltages are not correct, replace the interconnect board. If these voltages are correct, check the main motor cable for continuity. If continuity exists on each wire, replace the main motor. If continuity does not exist on one or more of the wires, replace the cable.

FRU Action · FRU Action · Diagnostic Information 2-21

Page 44 of the Lexmark E310 user manual — Main Motor Service Check
Page 44 · click to enlarge
Page 44

Model E312 Engine Board Main Motor Main Motor Cable

Check the engine board for the following voltages:

CN2-3 +24 V dc CN2-4 +24 V dc

If these voltages are not correct, replace the engine board. If these voltages are correct, check the main motor cable for continuity. If continuity exists on each wire, replace the main motor. If continuity does not exist on one or more of the wires, replace the cable.

FRU Action

Page 45 of the Lexmark E310 user manual — Operator Panel Service Check
Page 45 · click to enlarge
Page 45

Operator Panel Service Check

Inspect the operator panel cable for damage. Make sure the cable is plugged in securely.

Run POST and check each LED for proper operation.

Models E310 & E312 Operator Panel Operator Panel Cable

If more than one LED does not turn on or an individual LED stays on solid during POST, check the operator panel cable for continuity. Replace if defective. If the cable measures continuity, replace the operator panel.

Models E310 & E312 Operator Panel Operator Panel Cable Controller Board

If all LEDs are dim and operate erratically during POST or all LEDs come on and stay on solid during POST, replace the following FRUs one at a time in the order shown:

Controller Board Operator Panel Operator Panel Cable

If none of the LEDs come on, make sure the cable is properly connected to the operator panel and the controller board. Disconnect the cable and check it for continuity. Replace if necessary. If the cable measures continuity, measure the following voltages with the printer on at idle:

U5-1: Ground U5-2: +5 V dc U5-3: +5 V dc U5-5: +5 V dc U5-6: Ground

If these voltages are not correct, replace the controller board. If these voltages are correct, replace the operator panel.

FRU Action · Diagnostic Information 2-23

Page 46 of the Lexmark E310 user manual — Paper Jam error indication during POST
Page 46 · click to enlarge
Page 46

Operator Panel Button Service Check

Models E310 & E312 Operator Panel Operator Panel Cable

Disconnect the operator panel from the operator panel cable. Check the continuity between U5-1 and U5-2 on the operator panel as you press the operator panel button. As the button is pressed, continuity is present. Replace the operator panel if continuity is not present. If continuity is present, replace the operator panel cable.

Paper Feed Service Check

Paper Jam error indication during POST

Models E310 & E312 Exit Sensor Flag

If the exit sensor flag is not resting within the paper exit sensor during POST, the printer displays a paper jam message. Make sure the flag is operating freely and correctly installed.

Models E310 & E312 Input Paper Feed Sensor

Make sure the input paperfeed sensor is working properly. A stuck or incorrectly installed sensor causes this error.

FRU Action · FRU Action

Page 47 of the Lexmark E310 user manual — Paper picks but stops half way through the printer
Page 47 · click to enlarge
Page 47

Paper picks during POST and/or continuously

Models E310 & E312 Pick Roller Clutch Solenoid

Check the pick roller clutch for wear. The solenoid interacts with the clutch controlling motion of the pick roller. If the cam surface of the pick roller clutch assembly is worn, the solenoid may not stop the pick roller from rotating. Replace the pick roller clutch assembly if necessary. Make sure the spring on the solenoid is properly installed. If the spring is improperly installed or missing, the pick roller will continuously pick paper.

Paper picks but stops about an inch down the page

Models E310 & E312 Roller Guides

Check for correct position of roller guides on pick roller assembly.

Paper picks but stops half way through the printer

Model E310 Input Paper Feed Sensor Interconnect Board

Make sure the input paper feed sensor is working properly. Check for a broken or stuck flag on the input paper feed sensor. Check to make sure the cable is seated on the CN401 connector on the interconnect board. Disconnect the cable and check for the following voltages:

CN401-3 +5 V dc CN401-4 Ground

If these voltages are not correct, replace the interconnect board. If correct, replace the input paper feed sensor.

Show 4 more labels / short text on this page
FRU Action · FRU Action · FRU Action · Diagnostic Information 2-25
Page 48 of the Lexmark E310 user manual — Operator Panel Button Service Check
Page 48 · click to enlarge
Page 48

Model E312 Input Paper Feed Sensor Engine Board

Make sure the input paper feed sensor is working properly. Check for a broken or stuck flag on the input paper feed sensor. Check to make sure the cable is seated on the CN6 connector on the engine board. Disconnect the cable and check for the following voltages:

CN6-3 +5 V dc CN6-4 Ground

If these voltages are not correct, replace the engine board. If correct, replace the input paper feed sensor.

FRU Action

Page 49 of the Lexmark E310 user manual — Paper occasionally picks or picks multiple sheets at once
Page 49 · click to enlarge
Page 49

Paper never picks

Models E310 & E312 Paper Tray

Make sure the paper tray is correctly installed. The black mylar guide sheet in the front of the tray must be positioned in the paper path just behind the pick roller assembly. This guide sheet can easily block the paper path if installed incorrectly.

Model E310 Pick Roller Solenoid

Make sure solenoid is installed correctly and its cable is plugged into CN402 on the interconnect board. If installation is correct, disconnect the solenoid and check CN402-1 for +24 V dc. If the voltage is present, replace the solenoid. If the voltage is not present, replace the interconnect board.

Model E312 Pick Roller Solenoid

Make sure solenoid is installed correctly and its cable is plugged into CN4 on the engine board. If installation is correct, disconnect the solenoid and check CN4-1 for +24 V dc. If the voltage is present, replace the solenoid. If the voltage is not present, replace the engine board.

Paper occasionally picks or picks multiple sheets at once

Models E310 & E312 Pick Roller Assembly

Check pick roller assembly for wear. Replace as necessary.

Models E310 & E312 Paper Separator Assembly

Check the friction pad on the paper separator for signs of wear. Replace as necessary.

Models E310 & E312 Pick Roller Pad Assembly

Check the friction pad on the pick roller pad assembly for signs of wear. Replace as necessary.

FRU Action · FRU Action · Diagnostic Information 2-27

Page 50 of the Lexmark E310 user manual — Blank page
Page 50 · click to enlarge
Page 50

Paper "trees", wrinkles, stacks poorly or curls

Models E310 & E312 Transfer Roller

This problem is most likely due to a worn transfer roller. A worn transfer roller causes the printer to run hotter than required for the media being printed. Excessive heat can cause paper treeing problems, poor stacking or curl.

Print Quality Service Check

Blank page

Models E310 & E312 Toner Cartridge

Remove the toner cartridge and gently shake the assembly to evenly distribute the toner.

Printhead Printhead Cable HVPS Engine/LVPS Board (Model E310) Engine Board (Model E312)

Blank pages can be caused by a defective printhead assembly, high voltage power supply or engine/ LVPS board. Disconnect the printhead cable from the HVPS and measure the signals on connectors CN3 and CN4. Go to the “High Voltage Power Supply (model E310)” on page 5-16 in the connector locations chapter and check the voltage measurements. If the voltages are correct, check the printhead cable for continuity. If the cable measures continuity, replace the printhead. If the cable does not measure continuity, replace the cable. If the voltage measurements are not correct, replace the HVPS. If the problem still exists, replace the engine/LVPS board on the model E310 or the engine board on the model E312.

FRU Action · FRU Action

Page 51 of the Lexmark E310 user manual — Black page
Page 51 · click to enlarge
Page 51

Black page

Models E310 & E312 HVPS Contacts

Check the contacts for contamination and correct installation. Replace as necessary.

Model E310 Engine/LVPS Board HVPS Cable HVPS

Make sure the HVPS to engine/ LVPS cable is correctly installed. Disconnect the cable and measure the signals on CN2 of the engine/ LVPS board. Go to “Engine/LVPS Board (model E310)” on page 5-4 and check the voltage measurements. If the voltages are not correct, replace the engine/LVPS board. If the voltages are correct, check the HVPS to engine/LVPS cable for continuity. If the cable does not measure continuity, replace the cable. If the cable measures continuity, replace the HVPS.

Model E312 Engine Board HVPS Cable HVPS

Make sure the HVPS to engine board cable is correctly installed. Disconnect the cable and measure the signals on CN11 of the engine board. Go to the “Engine Board (model E312)” on page -9. Check the voltage measurements. If the voltages are not correct, replace the engine board. If the voltages are correct, check the HVPS to engine board cable for continuity. If the cable does not measure continuity, replace the cable. If the cable measures continuity, replace the HVPS.

FRU Action · Diagnostic Information 2-29

Page 52 of the Lexmark E310 user manual — Heavy background
Page 52 · click to enlarge
Page 52

Heavy background

Poor development or poorly charged toner particles cause excessive background. This is more noticeable as the toner cartridge nears end of life.

Models E310 & E12 Toner Cartridge

Make sure toner cartridge is correctly installed and the high voltage contacts are clean. If the cartridge is installed correctly, try a new cartridge.

Model E310 HVPS Contacts HVPS Board Engine/LVPS Board

Check the contacts for correct installation and contamination where contact is made with the toner cartridge and HVPS Board. Clean as necessary. If this does not correct the problem, replace the following FRUs one at a time in the order shown:

HVPS Board Engine/LVPS Board

Model E312 HVPS Contacts HVPS Board Engine Board

Check the contacts for correct installation and contamination where contact is made with the toner cartridge and HVPS Board. Clean as necessary. If this does not correct the problem, replace the following FRUs one at a time in the order shown:

HVPS Board Engine Board

FRU Action

Page 53 of the Lexmark E310 user manual — Variation in image density horizontally across page
Page 53 · click to enlarge
Page 53

Partial blank image/white spots (no periodic pattern)

Toner Cartridge Remove the toner cartridge and gently shake the assembly to evenly distribute the toner. If toner cartridge is low, try a new one.

Fuser Backup Roller Springs Check left and right backup roller springs and backup roller to ensure adequate even pressure is applied to the fuser hotroll.

Paper Make sure recommended paper is being used.

Variation in image density horizontally across page

Toner Cartridge The charge roll in the toner cartridge may have an unbalanced pressure against the PC drum. Try a new toner cartridge.

Transfer Roller Bearing Assembly Transfer Roller

Check the springs in the left and right transfer roller bearings. The bearing assemblies should support the transfer roller, applying even pressure to the PC drum. Replace either or both transfer roller bearing assemblies if the springs show signs of damage or fatigue. Inspect the transfer roller for signs of wear or damage and replace as necessary.

FRU Action · FRU Action · Diagnostic Information 2-31

Page 54 of the Lexmark E310 user manual — Periodic irregularity down page
Page 54 · click to enlarge
Page 54

Periodic irregularity down page

PC Drum (Toner Cartridge)

The PC drum or gear driving the PC drum may be contaminated or damaged. Inform the customer to replace the toner cartridge.

Distance Between Irregularity 94.5 mm

Charge Roller (Toner Cartridge)

The charge roller or gear driving the charge roller may be contaminated or damaged. Inform the customer to replace the toner cartridge.

Distance Between Irregularity 37.8 mm

Supply Roller (Toner Cartridge)

The supply roller or gear driving the supply roller may be contaminated or damaged. Inform the customer to replace the toner cartridge.

Distance Between Irregularity 40.1 mm

Developer Roller (Toner Cartridge)

The supply roller or gear driving the developer roller may be contaminated or damaged. Inform the customer to replace the toner cartridge.

Distance Between Irregularity 46.1 mm

The transfer roller or gear driving the transfer roller may contaminated or damaged. Inspect the roller and gear. Replace as necessary.

Distance Between Irregularity 46.0 mm

The hot roll of the fuser or gear driving the hot roll may be contaminated or damaged. Inspect the hot roll and gear. Replace or clean as necessary.

Distance Between Irregularity 56.7 mm

The backup roller of the fuser may be contaminated or damaged. Inspect and replace as necessary.

Distance Between Irregularity 69.1 mm

Show 4 more labels / short text on this page
FRU Action · Transfer Roller · Hot Roll · Backup Roller
Page 55 of the Lexmark E310 user manual — Light print
Page 55 · click to enlarge
Page 55

Poor fusing of image

Fuser Lamp The fuser may not be operating at the proper temperature to fuse the toner to the paper. Go to the “Cold Fuser Service Check” on page 2-17.

Paper Make sure recommended paper is being used.

Light print

Toner Cartridge Make sure the toner cartridge is installed correctly and is not low on toner. If the problem continues, install a new toner cartridge.

Transfer Roller HVPS Contact (Transfer Roller) HVPS Board

Check the transfer roller for signs of toner buildup and contamination. Inspect the HVPS contact (transfer roller) for contamination. Inspect the HVPS board for contamination where it meets the HVPS contacts. If all components appear free of contamination, replace the following FRUs one at a time in the order shown:

Transfer Roller HVPS Contact (Transfer Roller) HVPS Board

FRU Action · FRU Action · Diagnostic Information 2-33

Page 56 of the Lexmark E310 user manual — Incorrect characters print
Page 56 · click to enlarge
Page 56

White or black lines or bands

Toner Cartridge Paper Feed Drive Gears

Banding appears as light or dark horizontal lines on a uniformly gray page or on a page with a large area of graphics. Banding is primarily due to a variation in the speed of the paper as it feeds through the printer especially in the developer and transfer process. Inspect the toner cartridge and paper feed components, especially the drive gears, for signs of wear, debris, binds or damage.

Toner on back of page

Print Cartridge Inspect the overall paper path for signs of spilled toner. Gently clean the contaminated areas with a soft cloth or compressed air.

Fuser Hot Roll Backup Roller

The fuser hot roll can cause toner on the back of the paper if toner is building up on the hot roll. This buildup may transfer to the backup roller, later transferring to the backside of the paper. Inspect the hot roll and backup roller for signs of contamination and replace as necessary.

Transfer Roller A transfer roller contaminated with toner can cause toner to transfer to backside of printed pages. Inspect the transfer roller for contamination and replace as necessary.

Incorrect characters print

Make sure the correct printer driver software is installed. Incorrect software can cause incorrect characters to print and the image may not fit the page.

FRU Action · FRU Action

Page 57 of the Lexmark E310 user manual — Parallel Port Service Check
Page 57 · click to enlarge
Page 57

Parallel Port Service Check

1. Perform a print test to make sure the printer prints correctly. 2. Be sure the printer cable is designed for bidirectional printing. 3. Be sure the user application is set up correctly. Improper set up can prevent establishing a communication link with the printer. 4. Try enabling the parallel port pull-up resistors. Go to “Parallel Mode 1” on page 3-8. Try printing a test page after enabling resistors. If the printer still does not print, disable the resistors. 5. If the internal print test page prints correctly, the user application/printer driver is set up correctly and the correct bi- directional parallel cable is installed, yet the printer still fails to print on command from the host, replace the controller board.

Diagnostic Information 2-35

Page 58 of the Lexmark E310 user manual — Parallel Port Service Check
Page 58 · click to enlarge
Page 58
Page 58 of the Lexmark E310 user manual — Parallel Port Service Check
Page 59 of the Lexmark E310 user manual — Diagnostic Test
Page 59 · click to enlarge
Page 59

3. Diagnostic Aids

This chapter explains the tests and procedures you can run to identify printer failures and verify that repairs have corrected the problem.

Memory Test

The following tests run sequentially when performing this test:

Standard Memory Test Optional Memory Test

The memory test runs automatically during POST if a different size optional memory SIMM is installed since the last printer power on.

Perform the following steps to run the Memory Test:

1. Turn the printer off. 2. Open the top cover. 3. Press and hold the operator panel button as you turn on the printer. Release the button once the Error LED comes on solid. 4. Close the top cover. 5. If all the diagnostic tests run correctly, the Data LED blinks. If a test fails, the Error LED pattern for the service error code dis- plays on the operator panel. Go to the “Service Error Codes” on page 2-2 and take the indicated action for that error.

Diagnostic Test

Once the memory test is complete, the diagnostic test pages can be printed by briefly pressing the operator panel button. Two pages are printed. The first page is a listing of various printer settings and code level. The second page is used to inspect registration. If the printer requires a registration adjustment, you must contact your next level of support to obtain the software utility that enables you to adjust registration.

Diagnostic Aids 3-1

Page 60 of the Lexmark E310 user manual — Print Quality Test
Page 60 · click to enlarge
Page 60

Print Quality Test

There are three print quality test pages. The first page displays the installed printer base code level and user default settings for the following:

Top Margin Offset Left Margin Offset Printer Page Count Installed Memory PQET Setting (on/off) Toner Saver (on/off) Print Resolution Print Darkness

The next two test pages are used to evaluate print quality. One test page is gray and the other is black. Perform the following steps to print the second test page:

1. Turn the printer off. 2. Open the top cover. 3. Turn the printer power on. 4. When the Error LED comes on solid, double-click the operator panel button. 5. Once the Error and Press Button LEDs start blinking, close the top cover. 6. The Ready LED comes on solid and the Error and Press Button LED continue blinking. 7. Double-click the operator button four times. The Ready and Data LEDs come on solid while the Error and Press Button LEDs continue blinking. 8. Perform a long button press until all LEDs come on solid. 9. The test pages are printing. 10. When the test pages have finished printing, the Ready LED comes on solid and the Data LED goes off.

Page 61 of the Lexmark E310 user manual — Configuration Mode
Page 61 · click to enlarge
Page 61

User Mode Print Test

The User Mode Print Test Page displays the user default values, installed options, printer features, various typefaces, and the installed printer base code level.

1. Turn the printer power on. The Ready LED comes on solid (printer is in the ready state). 2. Press and release the operator panel button. 3. The Ready LED comes on solid and the Data LED blinks indicating the printer is busy. 4. The test page prints and the operator panel Ready LED comes on solid and the Data LED turns off. 5. The printer returns to the Ready mode.

Configuration Mode

The configuration mode gives the ability to set the following printer functions through the operator panel:

Enable Port NPA Mode Protocol Mode 1 Mode 2 Strobe Adjust

Enable Port NPA Mode

PPDS Activated Auto CRLF/LFCR

Parallel Port Settings · USB Settings · Diagnostic Aids 3-3

Page 62 of the Lexmark E310 user manual — Configuration Mode Operator Panel Overlays
Page 62 · click to enlarge
Page 62

Operator Panel Configuration Mode Button Definition

Brief Button Press Press the operator panel button no longer than three seconds.

This action moves through the configura- tion mode settings.

Long Button Press Press and hold the operator panel button for more than three seconds.

This action selects and saves the setting for the menu item dis- played. To indicate that the setting is saved, all LEDs blink once.

Press and release the operator panel button two times. Each press and release action must be performed within a half second.

This action moves through the configura- tion mode menu.

Perform the following steps to enter the configuration mode:

1. Turn the printer power off. 2. Open the top cover. 3. Turn the printer power on. 4. When the Error LED comes on solid, double-click the operator panel button. 5. When the Error and Press Button LEDs start blinking, close the top cover. The Ready LED comes on solid and the Error and Press Button LEDs continue blinking. 6. Double-click the operator panel button two times. The Load Paper LED comes on solid while the Error and Press Button LEDs continue blinking. 7. Perform a long button press. All LEDs blink once. The Ready LED stays on solid. The printer is in the configuration mode. 8. To exit the configuration mode, turn the printer power off.

Configuration Mode Operator Panel Overlays

When in configuration mode, the first menu item and its setting are displayed. The first menu item is the Parallel Port and is indicated by

Term Description Result · Double-Click Button Press

Page 63 of the Lexmark E310 user manual — USB NPA
Page 63 · click to enlarge
Page 63

the solid Ready LED. The setting of the menu item is indicated by the status of the Press Button LED. To change the menu item setting, briefly press the operator panel button. Once the setting you want is indicated by the status of the Press Button LED, perform a long button press to save the setting. All LEDs come on while the setting is saved. To select other menu items, double-click the operator panel button until the menu item LED you want is selected.

There are ten menu items that can be selected by using the five LEDs as indicated by the following overlays on two passes through the configuration menu. The first time through the menu the LED selected is on solid. The second time through the menu the LED selected is blinking.

First pass - LED on solid overlay.

Parallel Port Parallel NPA

PPDS

CRLF/LFCR

Second pass - LED blinking overlay

Parallel Mode 1 Parallel Mode 2

USB NPA

Show 8 more labels / short text on this page
Parallel Protocol · Off/On/Auto · Operator Panel Button · Parallel Strobe · USB Port · Off/On/Auto · Operator Panel Button · Diagnostic Aids 3-5
Page 64 of the Lexmark E310 user manual — Parallel NPA
Page 64 · click to enlarge
Page 64

Configuration Mode Settings

The following is a description of the available configuration mode menu items and settings. The asterisk (*) indicates the factory default setting.

Parallel Port

Parallel Port allows the user to enable or disable the parallel port. If the port is not being used, disabling it frees allocated memory to be used to process print jobs.

Perform the following steps to change the Parallel Port setting:

1. Enter the configuration mode. Note: The Parallel Port (Ready) LED comes on solid. The current Parallel Port setting is indicated by the Off/On/Auto (Press Button) LED. When the LED is off, the parallel port is disabled. When the LED is *blinking, the parallel port is enabled.
2. Perform a brief button press to select the Parallel Port setting. 3. Perform a long button press. All LEDs blink once, indicating the setting is saved. 4. Exit the configuration mode by turning the printer power off.

Parallel NPA

Parallel NPA mode allows two way communication between the host and the printer.

Perform the following steps to change the Parallel NPA setting:

1. Enter the configuration mode. 2. Perform a double click button press. This moves to the Parallel NPA item on the configuration menu. The Parallel NPA (Data) LED comes on solid. 3. The current Parallel NPA setting is indicated by the Off/On/Auto (Press Button) LED.
  • When the LED is on solid, all data received by the printer must be in NPA packets. Any non-packet data is rejected as bad packets.
  • When the LED is off, the printer is not performing any NPA processing.
Page 65 of the Lexmark E310 user manual — PPDS
Page 65 · click to enlarge
Page 65
  • When the LED is *blinking, the printer examines incoming data and decides whether it is receiving NPA packets. 4. Perform a brief button press to select the Parallel NPA setting. 5. Perform a long button press. All LEDs blink once, indicating the setting is saved. 6. Exit the configuration mode by turning the printer power off.

Parallel Protocol

The printer supports two parallel protocol settings: standard and fastbytes. When the protocol is set to standard, information is received at a normal transmission rate. When the protocol is set to fastbytes, information can be received at a much faster transmission rate provided the host computer supports the fastbytes mode.

Perform the following steps to change the Parallel Protocol setting:

1. Enter the configuration mode. 2. Perform a double click button press twice. This moves to the Parallel Protocol item on the configuration menu. The Parallel Protocol (Load Paper) LED comes on solid. 3. The current Parallel Protocol setting is indicated by the Off/On/ Auto (Press Button) LED. When the LED is off, the Parallel Protocol is set to standard. When the LED is *on, the Parallel Protocol is set to fastbytes. Perform a brief button press to select the Parallel Protocol setting. 4. Perform a long button press. All LEDs blink once, indicating the setting is saved. 5. Exit the configuration mode by turning the printer power off.

PPDS

To access the PPDS data stream, the PPDS setting must be set to active. When PPDS is activated, the default Printer Language is changed to PPDS and the default PCL and PostScript Smartswitch settings are changed to Off.

Perform the following steps to change the PPDS setting:

1. Enter the configuration mode. 2. Perform a double click button press three times. This moves to the PPDS item on the configuration menu. The PPDS (Paper Jam) LED comes on solid.

Diagnostic Aids 3-7

Page 66 of the Lexmark E310 user manual — Parallel Mode 1
Page 66 · click to enlarge
Page 66
3. The current PPDS setting is indicated by the Off/On/Auto (Press Button) LED. When the LED is *off, the PPDS is set to inactive. When the LED is on, the PPDS is set to active. Perform a brief button press to select the PPDS setting. 4. Perform a long button press. All LEDs blink once, indicating the setting is saved. 5. Exit the configuration mode by turning the printer power off.

CRLF/LFCR

This function controls whether or not the printer automatically performs a carriage return after a line feed control command and whether or not the printer automatically performs a line feed after a carriage return control command.

Perform the following steps to change the CRLF/LFCR setting:

1. Enter the configuration mode. 2. Perform a double click button press four times. This moves to the CRLF/LFCR item on the configuration menu. The CRLF/ LFCR (Error) LED comes on solid. 3. The current CRLF/LFCR setting is indicated by the Off/On/Auto (Press Button) LED.
  • When the LED is *off, Auto CR after LF is off and Auto LF after CR is off.
  • When the LED is on, Auto CR after LF is on and Auto LF after CR is off.
  • When the LED is blinking, Auto CR after LF is off and Auto LF after CR is on. 4. Perform a brief button press to select the CRLF/LFCR setting. 5. Perform a long button press. All LEDs blink once, indicating the setting is saved. 6. Exit the configuration mode by turning the printer power off.

Parallel Mode 1

Parallel Mode 1 controls whether or not resistors are enabled on the parallel post signals. The default is to not have the resistors enabled, however, this function is useful because some IBM clone PC’s have open collector outputs on their parallel port signals.

Page 67 of the Lexmark E310 user manual — Parallel Strobe
Page 67 · click to enlarge
Page 67

Perform the following steps to change the Parallel Mode 1 setting:

1. Enter the configuration mode. 2. Perform a double click button press five times. This moves to the Parallel Mode 1 item on the configuration menu. The Parallel Mode 1 (Ready) LED is blinking. 3. The current Parallel Mode 1 setting is indicated by the Off/On/ Auto (Press Button) LED. When the LED is off, the Parallel Mode 1 is set to off. When the LED is *on, the Parallel Mode 1 is set to on. Perform a brief button press to select the Parallel Mode 1 setting. 4. Perform a long button press. All LEDs blink once, indicating the setting is saved. 5. Exit the configuration mode by turning the printer power off.

Parallel Mode 2

Parallel Mode 2 controls whether or not the parallel port data is sampled on the leading or trailing edge of strobe. The default is to sample on the leading edge of strobe, however, some IBM clone PC’s assumes that a printer will sample on the trailing edge.

Perform the following steps to change the Parallel Mode 2 setting:

1. Enter the configuration mode. 2. Perform a double click button press six times. This moves to the Parallel Mode 2 item on the configuration menu. The Parallel Mode 2 (Data) LED is blinking. 3. The current Parallel Mode 2 setting is indicated by the Off/On/ Auto (Press Button) LED. When the LED is off, the Parallel Mode 2 is set to sample on trailing edge. When the LED is *on, the Parallel Mode 2 is set to sample on leading edge. Perform a brief button press to select the Parallel Mode 2 setting. 4. Perform a long button press. All LEDs blink once, indicating the setting is saved. 5. Exit the configuration mode by turning the printer power off.

Parallel Strobe

This setting allows the user to adjust the factory setting for the amount of time strobe is sampled to determine that valid data is

Diagnostic Aids 3-9

Page 68 of the Lexmark E310 user manual — USB Port
Page 68 · click to enlarge
Page 68

available on the parallel port. Each increment of the strobe adjust value means the strobe is sampled 50ns longer.

Perform the following steps to change the Parallel Strobe Adjust:

1. Enter the configuration mode. 2. Perform a double click button press seven times. This moves to the Parallel Strobe item on the configuration menu. The Parallel Strobe (Load Paper) LED is blinking. 3. The current Parallel Strobe setting is indicated by the Off/On/ Auto (Press Button) LED. When the LED is *off, the Parallel Strobe is set to normal. When the LED is on, the Parallel Strobe is set to +1. When the LED is blinking, the Parallel Strobe is set to +2. Perform a brief button press to select the Parallel Strobe setting. 4. Perform a long button press. All LEDs blink once, indicating the setting is saved. 5. Exit the configuration mode by turning the printer power off.

USB Port

This menu item allows the user to enable or disable the USB port. If the port is not being used, disabling it frees allocated memory to be used to process print jobs.

Perform the following steps to change the USB Port setting:

1. Enter the configuration mode. 2. Perform a double click button press eight times. This moves to the USB Port item on the configuration menu. The USB Port (Paper Jam) LED is blinking. 3. The current USB Port setting is indicated by the Off/On/Auto (Press Button) LED. When the LED is off, the USB Port is disabled. When the LED is *blinking, the USB Port is enabled. Perform a brief button press to select a different USB Port setting. 4. Perform a long button press. All LEDs blink once, indicating the setting is saved. 5. Exit the configuration mode by turning the printer power off.

Page 69 of the Lexmark E310 user manual — Hex Trace
Page 69 · click to enlarge
Page 69

USB NPA

USB NPA mode allows for two way communication between the host and the printer.

Perform the following steps to change the USB NPA setting:

1. Enter the configuration mode. 2. Perform a double click button press nine times. This moves to the USB NPA mode item on the configuration menu. The USB NPA (Error) LED is blinking. 3. The current USB NPA setting is indicated by the Off/On/Auto (Press Button) LED.
  • When the LED is off, the USB port does not search for NPA data within the received data.
  • When the LED is *blinking, the USB port searches for optional NPA data within the received data.
  • When the LED is on solid, the USB port requires that data sent to the printer be in NPA format. 4. Perform a brief button press to select a different USB NPA setting. 5. Perform a long button press. All LEDs blink once, indicating the setting is saved. 6. Exit the configuration mode by turning the printer power off.

Hex Trace

When the printer is in Hex Trace, it prints a hexadecimal and a character representation of a print job. The printer does not recognize any print controls or commands in this mode. A Hex Trace printout is used to help isolate the cause of print problems.

When a job is printed, the printer operator panel displays the Hex Trace indication, (Ready LED blinking), showing that the printer remains in the Hex Trace mode. Turn the printer power off or do an operator panel reset (long button press) to exit the Hex Trace mode.

Perform the following steps to enter the Hex Trace mode:

1. Turn the printer power off. 2. Open the top cover. 3. Turn the printer power on.

Diagnostic Aids 3-11

Page 70 of the Lexmark E310 user manual — Restoring Factory Defaults
Page 70 · click to enlarge
Page 70

4. When the Error LED comes on solid, double-click the opera- tor panel button. 5. Once the Error and Press Button LEDs start to blink, close the top cover. 6. The Ready LED comes on solid and the Error and Press Button LEDs continue blinking. 7. Double-click the operator button three times. The Paper Jam LED comes on solid while the Error and Press Button LEDs continue blinking. 8. Perform a long button press until all LEDs come on solid. The printer is in Hex Trace mode 9. To exit the Hex Trace mode, turn the printer power off.

Restoring Factory Defaults

Restoring factory defaults returns the printer settings to the original factory settings.

Perform the following steps to invoke factory defaults:

1. Turn the printer power off. 2. Open the top cover. 3. Turn the printer power on. 4. When the Error LED comes on solid, double-click the opera- tor panel button. 5. Once the Error and Press Button LEDs start blinking, close the top cover. 6. The Ready LED comes on solid and the Error and Press Button LEDs continue blinking. 7. Double-click the operator button one time. The Data LED comes on solid while the Error and Press Button LEDs con- tinue blinking. 8. Perform a long button press until all LEDs come on solid. 9. The printer is reset to factory defaults.

Page 71 of the Lexmark E310 user manual — Engine Clean Cycle
Page 71 · click to enlarge
Page 71

Engine Clean Cycle

The Engine Clean Cycle function prints one blank page in a special cleaning mode. The cleaning mode helps eliminate small specs of toner present in the background when printing.

Perform the following steps to perform the Engine Clean Cycle:

1. Turn the printer power off. 2. Open the top cover. 3. Turn the printer power on. 4. When the Error LED comes on solid, double-click the operator panel button. 5. Once the Error and Press Button LEDs start blinking, close the top cover. 6. The Ready LED comes on solid and the Error and Press Button LEDs continue blinking. 7. Perform a long button press until all LEDs come on solid. 8. The printer feeds one page from the automatic paper feed slot and then returns to normal printing mode.

Diagnostic Aids 3-13

Page 72 of the Lexmark E310 user manual — Printer Operation
Page 72 · click to enlarge
Page 72

Toggle Demo/Normal Mode

The Toggle Demo/Normal Mode function enables or disables the printer’s retail demo mode. When the printer is in Demo mode, demo pages can be printed by briefly pressing the operator panel button.

Perform the following steps to enter Toggle Demo/Normal Mode:

1. Turn the printer power off. 2. Open the top cover. 3. Turn the printer power on. 4. When the Error LED comes on solid, double-click the operator panel button. 5. Once the Error and Press Button LEDs start blinking, close the top cover. 6. The Ready LED comes on solid and the Error and Press Button LEDs continue blinking. 7. Double-click the operator button five times. The Ready and Load Paper LEDs come on solid while the Error and Press Button LEDs continue blinking. 8. Perform a long button press until all LEDs come on solid. The printer is in Demo mode. 9. To return the printer to Normal mode, repeat steps 1 through 8.

Printer Operation

Paper is held in a 150 page tray where it is picked by a center-fed "D" shape pick roller. The paper follows an "L" shape path as it moves through the printer. Images are created with toner on an OPC drum within the toner cartridge. A transfer roller then draws the toner off the OPC drum onto the paper. Once the toner is affixed to the paper by the fuser, the paper exits either the top or front of the printer.

Page 73 of the Lexmark E310 user manual — Paper Path
Page 73 · click to enlarge
Page 73

Paper Path

Lexmark E310 — Paper Path diagram (page 73)
Fig. 11 · Paper Path

Diagnostic Aids 3-15

Page 74 of the Lexmark E310 user manual — Paper Path
Page 74 · click to enlarge
Page 74
Page 74 of the Lexmark E310 user manual — Paper Path
Page 75 of the Lexmark E310 user manual — Handling ESD-Sensitive Parts
Page 75 · click to enlarge
Page 75

4. Repair Information

Handling ESD-Sensitive Parts

Many electronic products use parts that are known to be sensitive to electrostatic discharge (ESD). To prevent damage to ESD-sensitive parts, follow the instructions below in addition to all the usual precautions, such as turning off power before removing logic boards:

  • Keep the ESD-sensitive part in its original shipping container (a special “ESD bag”) until you are ready to install the part into the machine.
  • Make the least-possible movements with your body to prevent an increase of static electricity from clothing fibers, carpets, and furniture.
  • Put the ESD wrist strap on your wrist. Connect the wrist band to the system ground point. This discharges any static electricity in your body to the machine.
  • Hold the ESD-sensitive part by its edge connector shroud (cover); do not touch its pins. If you are removing a pluggable module, use the correct tool.
  • Do not place the ESD-sensitive part on the machine cover or on a metal table; if you need to put down the ESD-sensitive part for any reason, first put it into its special bag.
  • Machine covers and metal tables are electrical grounds. They increase the risk of damage because they make a discharge path from your body through the ESD-sensitive part. (Large metal objects can be discharge paths without being grounded.)
  • Prevent ESD-sensitive parts from being accidentally touched by other personnel. Install machine covers when you are not working on the machine, and do not put unprotected ESD-sensitive parts on a table.
  • If possible, keep all ESD-sensitive parts in a grounded metal cabinet (case).
  • Be extra careful in working with ESD-sensitive parts when coldweather heating is used because low humidity increases static electricity.

Repair Information 4-1

Page 76 of the Lexmark E310 user manual — Front Cover and Face Up Cover
Page 76 · click to enlarge
Page 76

Removal Procedures

Screw Identification Table

Lexmark E310 — Screw Identification Table diagram (page 76)
Fig. 12 · Screw Identification Table

Type 1 Screw Type 2 Screw Type 3 Screw Type 4 Screw

Covers

Front Cover and Face Up Cover

1. Press the cover inward to release it and pull it forward.
Lexmark E310 — Front Cover and Face Up Cover diagram (page 76)
Fig. 13 · Front Cover and Face Up Cover
Page 77 of the Lexmark E310 user manual — Removal Procedures
Page 77 · click to enlarge
Page 77
2. Remove the face up cover.
Lexmark E310 — Removal Procedures diagram (page 77)
Fig. 14 · Removal Procedures
3. Open the front cover.
Lexmark E310 — Removal Procedures diagram (page 77)
Fig. 15 · Removal Procedures

Repair Information 4-3

Page 78 of the Lexmark E310 user manual — Removal Procedures
Page 78 · click to enlarge
Page 78
4. Remove the screw from the support on each side of the printer.
Lexmark E310 — Removal Procedures diagram (page 78)
Fig. 16 · Removal Procedures
Lexmark E310 — Removal Procedures diagram (page 78)
Fig. 17 · Removal Procedures
Page 79 of the Lexmark E310 user manual — Rear and Top Cover
Page 79 · click to enlarge
Page 79

Rear and Top Cover

1. Remove the three screws, press the retaining tabs and remove the rear cover.
Lexmark E310 — Rear and Top Cover diagram (page 79)
Fig. 18 · Rear and Top Cover
2. Remove the front cover and face up cover. 3. Remove the two screws and remove the top cover.
Lexmark E310 — Rear and Top Cover diagram (page 79)
Fig. 19 · Rear and Top Cover

Repair Information 4-5

Page 80 of the Lexmark E310 user manual — Side Covers
Page 80 · click to enlarge
Page 80

Side Covers

1. Remove the front cover, face up cover, top cover and rear cover. 2. Remove the two screws securing the rear of each side cover. 3. Release the side cover tabs as shown and remove the left and right side covers.
Page 81 of the Lexmark E310 user manual — Frame Assembly
Page 81 · click to enlarge
Page 81

Frame Assembly

1. Remove all covers. 2. Remove the HVPS. 3. Remove the two screws and remove the solenoid. 4. Remove the six screws and remove the frame assembly.
Lexmark E310 — Frame Assembly diagram (page 81)
Fig. 20 · Frame Assembly

Repair Information 4-7

Page 82 of the Lexmark E310 user manual — Fuser Assembly
Page 82 · click to enlarge
Page 82

Fuser Assembly

1. Remove all covers. 2. Remove the wire cover mounting screw (A). 3. Remove the two fuser lamp wire mounting screws (B). 4. Unplug the connector from the engine/LVPS board. 5. Remove the two fuser mounting screws (C). 6. Release the two snaps holding the fuser down.
Lexmark E310 — Fuser Assembly diagram (page 82)
Fig. 21 · Fuser Assembly
Page 83 of the Lexmark E310 user manual — Fuser Assembly
Page 83 · click to enlarge
Page 83
7. Slide the fuser in the direction of the arrows and remove the fuser. Note: The backup roller can fall from the printer if the printer is turned on its side with the fuser removed.
Lexmark E310 — Fuser Assembly diagram (page 83)
Fig. 22 · Fuser Assembly

Repair Information 4-9

Page 84 of the Lexmark E310 user manual — HVPS
Page 84 · click to enlarge
Page 84

HVPS

1. Remove all covers. 2. Remove the HVPS board mounting screws.
Lexmark E310 — HVPS diagram (page 84)
Fig. 23
Page 85 of the Lexmark E310 user manual — HVPS
Page 85 · click to enlarge
Page 85
3. Unplug the three cables from the connectors on top of the HVPS. 4. Unplug the cable from the lower connector inside the HVPS and remove the HVPS. Note: The high voltage contacts can fall from the printer with the HVPS removed. Three contacts with the shorter springs are installed in the hole marked L+S. The contact with the longer spring is installed in the hole marked L+L.
Lexmark E310 — HVPS diagram (page 85)
Fig. 24

Repair Information 4-11

Page 86 of the Lexmark E310 user manual — Interconnect Board (model E310)
Page 86 · click to enlarge
Page 86

Interconnect Board (model E310)

1. Remove the LVPS. 2. Unplug all connectors from the interconnect board. 3. Remove the screws and remove the interconnect board.
Page 87 of the Lexmark E310 user manual — Engine/LVPS Board (model E310)
Page 87 · click to enlarge
Page 87

Engine/LVPS Board (model E310)

1. Turn the printer upside down. 2. Remove all screws securing the SIMM access panel. 3. Remove the SIMM access panel.

Repair Information 4-13

Page 88 of the Lexmark E310 user manual — Engine/LVPS Board (model E310)
Page 88 · click to enlarge
Page 88
4. Unplug all the connectors from the engine/LVPS board. 5. Remove the five screws and remove the engine/LVPS board.
Lexmark E310 — Engine/LVPS Board (model E310) diagram (page 88)
Fig. 25 · Engine/LVPS Board (model E310)
Page 89 of the Lexmark E310 user manual — Engine/LVPS Board (model E312)
Page 89 · click to enlarge
Page 89

Engine/LVPS Board (model E312)

1. Turn the printer upside down. 2. Remove all screws securing the SIMM access panel. 3. Remove the SIMM access panel.

Repair Information 4-15

Page 90 of the Lexmark E310 user manual — Engine/LVPS Board (model E312)
Page 90 · click to enlarge
Page 90
4. Remove the five screws securing the LVPS shield. 5. Lift the shield from the printer and disconnect all the cables from the LVPS.
Lexmark E310 — Engine/LVPS Board (model E312) diagram (page 90)
Fig. 26 · Engine/LVPS Board (model E312)
6. Remove the screws mounting the LVPS to the shield and remove the LVPS. 7. Disconnect all the cables from the engine board. 8. Remove the screws mounting the engine board to the lower frame and remove the engine board.
Page 91 of the Lexmark E310 user manual — Main Drive Assembly
Page 91 · click to enlarge
Page 91

Main Drive Assembly

1. Remove all covers. 2. Remove the six main drive assembly mounting screws. 3. Unplug the connector and remove the main drive assembly.
Lexmark E310 — Main Drive Assembly diagram (page 91)
Fig. 27 · Main Drive Assembly

Repair Information 4-17

Page 92 of the Lexmark E310 user manual — Pick Roll Assembly
Page 92 · click to enlarge
Page 92

Pick Roll Assembly

1. Remove all the covers. 2. Remove the high voltage power supply. 3. Remove the roller bearing.
Lexmark E310 — Pick Roll Assembly diagram (page 92)
Fig. 28 · Pick Roll Assembly
Page 93 of the Lexmark E310 user manual — Pick Roll Assembly
Page 93 · click to enlarge
Page 93
4. Remove the roller access cover on the left side of the pick roller assembly. 5. Remove the upper frame. 6. Remove the pick up roller gear and clutch. 7. Lift the pick roll assembly from the printer.
Lexmark E310 — Pick Roll Assembly diagram (page 93)
Fig. 29 · Pick Roll Assembly

Repair Information 4-19

Page 94 of the Lexmark E310 user manual — Printhead Assembly
Page 94 · click to enlarge
Page 94

Printhead Assembly

1. Remove the top cover. 2. Unplug all the connectors from the printhead. 3. Remove the four mounting screws and remove the printhead.
Lexmark E310 — Printhead Assembly diagram (page 94)
Fig. 30 · Printhead Assembly
Page 95 of the Lexmark E310 user manual — Transfer Roll
Page 95 · click to enlarge
Page 95

Transfer Roll

1. Remove the front cover and face up cover. 2. Remove the black cover on the left end of the transfer roll. 3. Press the latches on the bearings to release them from the lower frame. 4. Lift the transfer roll from the printer.

Repair Information 4-21

Page 96 of the Lexmark E310 user manual — Transfer Roll
Page 96 · click to enlarge
Page 96
Page 96 of the Lexmark E310 user manual — Transfer Roll
Page 97 of the Lexmark E310 user manual — 4 N/A
Page 97 · click to enlarge
Page 97

5. Connector Locations

Controller Board (model E310/E312)

Connector Pin No. Signal

J1 Printhead 1 N/A

U5 Operator Panel (signals at idle)

2 +5 V dc

3 +5 V dc

4 N/A

5 +5 V dc

J7 Engine/LVPS Board 1 +5 V dc

2 +5 V dc

3 +5 V dc

4 +5 V dc

5 +5 V dc

6 +5 V dc

8 +5 V dc

9 +5 V dc

10 +5 V dc

12 +5 V dc

13 +5 V dc

14 +5 V dc

Show 6 more labels / short text on this page
2 Ground · 1 Ground · 6 Ground · 7 Ground · 11 Ground · Connector Locations 5-1
Page 98 of the Lexmark E310 user manual — 5. Connector Locations
Page 98 · click to enlarge
Page 98

Connector Pin No. Signal

J7 (continued) 15 +5 V dc

16 +5 V dc

17 +5 V dc

23 +5 V dc

24 +5 V dc

Show 5 more labels / short text on this page
18 Ground · 19 Ground · 20 Ground · 21 Ground · 22 Ground
Page 99 of the Lexmark E310 user manual — 5. Connector Locations
Page 99 · click to enlarge
Page 99

Connector Locations 5-3

Page 100 of the Lexmark E310 user manual — 5 VDO
Page 100 · click to enlarge
Page 100

Engine/LVPS Board (model E310)

Connector Pin No. Signal

CN201 Power Switch 1 AC In

CN202 Fuser Lamp 1 AC In

CN1 Thermistor 1 THERM

2 +3.9 V dc

CN2 HVPS/Printhead 1 +24 V dc SWITCH

2 +24 V dc

4 +24 V dc

5 VDO

6 MHV

7 LDON

8 SUPPLY

10 DEV350

Show 4 more labels / short text on this page
2 AC In · 2 AC In · 3 Ground · 9 Ground
Page 101 of the Lexmark E310 user manual — 21 AGND
Page 101 · click to enlarge
Page 101

Connector Pin No. Signal

CN2 (continued) 11 HSYNC

12 THVPWM

13 EXT CLK

16 THVEA

17 LREADY

18 DEV300

19 P MOTOR

20 +5 V dc

21 AGND

22 AGND

23 THVREAD

24 AGND

14 Ground · 15 Ground · Connector Locations 5-5

Page 102 of the Lexmark E310 user manual — 19 PMOTOR EXT J
Page 102 · click to enlarge
Page 102

Connector Pin No. Signal

CN4 Interconnect Board 1 DEV FUSE FAN J

2 MOTOR EA J

3 MOTOR PB J

4 MOTOR PA J

5 AGND

6 NEW DEV J

7 PFEED J

8 AGND

11 CLUTCH J

12 PEMPTY J

13 +24 V dc

14 PNARROW J

15 +5 V dc

16 +24 V dc

17 PTL J

18 +5 V dc

19 PMOTOR EXT J

20 EXT CLK J

9 Ground · 10 Ground

Page 103 of the Lexmark E310 user manual — 23 VDO
Page 103 · click to enlarge
Page 103

Connector Pin No. Signal

CN5 Controller Board 1 EBUSY

3 EMSG

4 EXITPAP

5 CCLK

6 PRINT

7 VDI

9 PSYNC

10 READY

11 HSYNC

13 +5 V dc

14 CMSG

15 +5 V dc

16 +5 V dc

18 +5 V dc

23 VDO

Show 10 more labels / short text on this page
2 Not Used · 8 Not Used · 12 Not Used · 17 Ground · 19 Ground · 20 Ground · 21 Ground · 22 Ground · 24 Not Used · Connector Locations 5-7
Page 104 of the Lexmark E310 user manual — Engine/LVPS Board (model E310)
Page 104 · click to enlarge
Page 104
Page 104 of the Lexmark E310 user manual — Engine/LVPS Board (model E310)
Page 105 of the Lexmark E310 user manual — 23 VDO
Page 105 · click to enlarge
Page 105

Engine Board (model E312)

Connector Pin No. Signal

CN1 Controller Board 1 EBUSY

3 EMSG

4 EXITPAP

5 CCLK

6 PRINT

7 VDI

9 PSYNC

10 READY

11 HSYNC

13 +5 V dc

14 CMSG

15 +5 V dc

16 +5 V dc

18 +5 V dc

23 VDO

Show 10 more labels / short text on this page
2 Not Used · 8 Not Used · 12 Not Used · 17 Ground, Floating · 19 Ground, Floating · 20 Ground, Floating · 21 Ground, Floating · 22 Ground, Floating · 24 Not Used · Connector Locations 5-9
Page 106 of the Lexmark E310 user manual — 1 PEMPTY
Page 106 · click to enlarge
Page 106

Connector Pin No. Signal

CN2 Motor 1 OUTA

2 OUTB

3 +24 V dc

4 +24 V dc

5 OUTA*

6 OUTB*

CN3 Fan 1 +24 V dc Switch

CN4 Clutch 1 +24 V dc Switch

CN5 Paper Present Sensor

1 PEMPTY

2 +5 V dc

CN6 Paper Feed/Paper Narrow Sensor

3 +5 V dc

Show 7 more labels / short text on this page
2 Not Used · 3 Fan · 2 Clutch · 3 Ground, Floating · 1 P Feed · 2 P Width · 4 Ground, Floating
Page 107 of the Lexmark E310 user manual — 1 PTL
Page 107 · click to enlarge
Page 107

Connector Pin No. Signal

CN7 LVPS 1 +5 V dc

2 +5 V dc

6 +24 V dc Switch

9 +24 V dc

10 +24 V dc

CN8 Pre-Transfer LED (PTL)

1 PTL

CN9 DCV 1 Not Used

CN10 Thermistor 1 THERM

Show 12 more labels / short text on this page
3 Ground, Floating · 4 Ground, Floating · 5 Fuser On · 7 Ground · 8 Ground · 2 Ground, Floating · 2 Not Used · 3 Not Used · 4 Not Used · 2 Not Used · 3 Ground, Floating · Connector Locations 5-11
Page 108 of the Lexmark E310 user manual — 23 THVREAD
Page 108 · click to enlarge
Page 108

Connector Pin No. Signal

CN11 HVPS 1 +24 V dc

2 +24 V dc Switch

3 +24 V dc

4 +24 V dc Switch

5 LREADY

6 THVEA

7 VDO

8 THV PWM

9 HSYNC

10 MHV PWM

11 DEVEA-A

13 LDON

14 DEVEA-B

18 +5 V dc

20 +5 V dc

23 THVREAD

24 PMOTOR

Show 7 more labels / short text on this page
12 Supply EA · 15 Ground, Floating · 16 Ground, Floating · 17 Ground, Floating · 19 Ground · 21 Ground · 22 Ground
Page 109 of the Lexmark E310 user manual — Engine Board (model E312)
Page 109 · click to enlarge
Page 109

Connector Locations 5-13

Page 110 of the Lexmark E310 user manual — LVPS (model E312)
Page 110 · click to enlarge
Page 110

LVPS (model E312)

Connector Pin No. Signal

CN501 Power Switch 1 AC In

CN502 Fuser Lamp 1 AC In

CN503 Engine Board 1 +5 V dc

2 +5 V dc

6 +24 V dc Switch

9 +24 V dc

10 +24 V dc

Show 7 more labels / short text on this page
2 AC In · 2 AC In · 3 Ground, Floating · 4 Ground, Floating · 5 Fuser On · 7 Ground · 8 Ground
Page 111 of the Lexmark E310 user manual — LVPS (model E312)
Page 111 · click to enlarge
Page 111

Connector Locations 5-15

Page 112 of the Lexmark E310 user manual — 20 P MOTOR
Page 112 · click to enlarge
Page 112

High Voltage Power Supply (model E310)

Connector Pin No. Signal

CN1 Engine/LVPS Board 1 +24 V dc

2 +24 V dc SWITCH

3 +24 V dc

5 MHV

6 VDO

7 SUPPLY

8 LDON

9 DEV350

11 THVPWM

12 HSYNC

14 EXT CLK

15 THVEA

17 DEV300

18 LREADY

19 +5 V dc

20 P MOTOR

21 AGND

22 AGND

23 AGND

24 THVREAD

Show 4 more labels / short text on this page
4 Ground · 10 Ground · 13 Ground · 16 Ground
Page 113 of the Lexmark E310 user manual — 4 LDON
Page 113 · click to enlarge
Page 113

Connector Pin No. Signal

CN2 Cover Open Switch 1 +24 V dc SWITCH

3 +24 V dc

CN3 Printhead 1 +24 V dc SWITCH

2 AGND

3 P MOTOR

4 LREADY

5 EXT CLK

CN4 Printhead 1 HSYNC

2 +5 V dc SWITCH

4 LDON

5 VDO

Show 4 more labels / short text on this page
2 Not Used · 3 Ground · 6 Ground · Connector Locations 5-17
Page 114 of the Lexmark E310 user manual — 23 PMOTOR
Page 114 · click to enlarge
Page 114

High Voltage Power Supply (model E312)

Connector Pin No. Signal

CN1 Engine Board 1 +24 V dc SWITCH

2 +24 V dc

3 +24 V dc SWITCH

4 + 24 V dc

5 THVEA

6 LREADY

7 THV PWM

8 VDO

9 MHV PWM

10 HSYNC

11 SUPPLYEA

12 DEVEA-A

13 DEVEA-B

14 LDON

19 +5 V dc

23 PMOTOR

24 THVREAD

Show 7 more labels / short text on this page
15 Ground, Floating · 16 Ground, Floating · 17 +5 Vdc · 18 Ground, Floating · 20 Ground · 21 Ground · 22 Ground
Page 115 of the Lexmark E310 user manual — 4 LDON
Page 115 · click to enlarge
Page 115

Connector Pin No. Signal

CN2 Cover Open Switch 1 +24 V dc SWITCH

2 +5 V dc SWITCH

3 +5 V dc

4 +24 V dc

CN3 Printhead 1 +24 V dc SWITCH

2 AGND

3 P MOTOR

4 LREADY

5 EXT CLK

CN4 Printhead 1 HSYNC

2 +5 V dc SWITCH

4 LDON

5 VDO

3 Ground, Floating · 6 Not Used · Connector Locations 5-19

Page 116 of the Lexmark E310 user manual — High Voltage Power Supply (model E312)
Page 116 · click to enlarge
Page 116
Page 116 of the Lexmark E310 user manual — High Voltage Power Supply (model E312)
Page 117 of the Lexmark E310 user manual — 5 OUT A*
Page 117 · click to enlarge
Page 117

Interconnect Board (model E310)

Connector Pin No. Signal

CN401 Paper Feed/Paper Narrow Sensor

1 PFEED J

2 PNARROW J

3 +5 V dc

CN402 Clutch 1 +24 V dc

2 CLUTCH J

CN403 Paper Empty Sensor

1 PEMPTY J

2 +5 V dc

CN404 Developer Fuse 1 Not Used

CN405 Main Motor 1 OUT A

2 OUT B

3 +24 V dc

4 +24 V dc

5 OUT A*

6 OUT B*

Show 4 more labels / short text on this page
4 Ground · 3 Ground · 2 Not Used · Connector Locations 5-21
Page 118 of the Lexmark E310 user manual — 2 N/A
Page 118 · click to enlarge
Page 118

Connector Pin No. Signal

1 MOTOR EA J

2 DEV FUSE FAN J

3 MOTOR PA J

4 MOTOR PB J

5 NEW DEV J

6 AGND

7 AGND

8 PFEED J

11 PEMPTY J

12 CLUTCH J

13 PNARROW J

14 +24 V dc

15 +24 V dc

16 +5 V dc

17 +5 V dc

18 PTL J

19 EXT CLK J

20 PMOTOR EXT J

CN407 Pre-Transfer LED (PTL)

1 PTL J

2 +5 V dc

CN408 Cooling Fan 1 DEV FAN J

2 N/A

3 +24 V dc

CN406 Engine/LVPS Board · 9 Ground · 10 Ground

Page 119 of the Lexmark E310 user manual — Interconnect Board (model E310)
Page 119 · click to enlarge
Page 119

Connector Locations 5-23

Page 120 of the Lexmark E310 user manual — Interconnect Board (model E310)
Page 120 · click to enlarge
Page 120
Page 120 of the Lexmark E310 user manual — Interconnect Board (model E310)
Page 121 of the Lexmark E310 user manual — How To Use This Parts Catalog
Page 121 · click to enlarge
Page 121

6. Parts Catalog

How To Use This Parts Catalog

  • SIMILAR ASSEMBLIES: If two assemblies contain a majority of identical parts, they are shown on the same list. Common parts are shown by one index number. Parts peculiar to one or the other of the assemblies are listed separately and identified by description.
  • AR: (As Required) in the Units column indicates that the quantity is not the same for all machines.
  • NS: (Not Shown) in the Asm-Index column indicates that the part is procurable but is not pictured in the illustration.
  • PP: (Parts Packet) in the parts description column indicates the part is contained in a parts packet.
  • INDENTURE: The indenture is marked by a series of dots located before the parts description. The indenture indicates the relationship of a part to the next higher assembly. For example:

INDENTURE RELATIONSHIP OF PARTS (No dot) MAIN ASSEMBLY (One dot) o Detail parts of a main assembly (One dot) o Subassembly of the main assembly (Two dot) o o Detail part of a one-dot subassembly (Two dot) o o Subassembly of a one-dot subassembly

Parts Catalog 6-1

Page 122 of the Lexmark E310 user manual — Assembly 1: Covers
Page 122 · click to enlarge
Page 122

Assembly 1: Covers

Lexmark E310 — Assembly 1: Covers diagram (page 122)
Fig. 31 · Assembly 1: Covers
Page 123 of the Lexmark E310 user manual — Assembly 1: Covers
Page 123 · click to enlarge
Page 123

Part Number Units Description

1-1 12G0021 1 Extender, Paper Support

1-2 12G0022 1 Support, Paper E310

1-2 12G1939 1 Support, Paper E312

1-3 12G0175 1 Cover Asm, Cooling Air/Stacker

1-4 12G0024 1 Stacker Assembly, Paper

1-5 12G0025 1 Support, Open Cover

1-6 12G0126 2 Guide, Paper Stacker

1-7 12G0030 1 Button, Operator Panel

1-8 12G0031 1 Lens, Operator Panel

1-9 12G0032 1 Panel, Operator

1-10 12G1850 1 Cover, Op Panel Cable

1-11 12G0027 1 Cable Asm, Operator Panel

1-12 6 Screw, Type 1 PP 12G0101

1-13 12G0181 2 Latch, Front Exit

1-14 12G0029 1 Tray, Front Exit

1-15 12G1846 1 Cover, Front w/English Overlay E310

1-15 12G1874 1 Cover, Front w/English Overlay E312

1-15 12G3668 1 Cover, Front w/English Overlay E312L

NS 12G3972 1 Op Panel Overlay, English

NS 12G0112 1 Packet, WT Op Panel Overlay

Asm- Index · Parts Catalog 6-3

Page 124 of the Lexmark E310 user manual — Assembly 1: Covers (continued)
Page 124 · click to enlarge
Page 124

Assembly 1: Covers (continued)

Lexmark E310 — Assembly 1: Covers (continued) diagram (page 124)
Fig. 32 · Assembly 1: Covers (continued)
Page 125 of the Lexmark E310 user manual — Assembly 1: Covers
Page 125 · click to enlarge
Page 125

Part Number Units Description

1-17 12G0035 1 Tray Asm, Paper E310

1-17 12G1938 1 Tray Asm, Paper E312

1-18 12G0098 1 Cover Asm, Rear

1-19 7 Screw, Type 1 PP 12G0101

1-20 12G1847 1 Cover, Right Side

1-21 12G0037 1 Cover, Lower Front

1-22 12G0040 1 Cover, Left Side

1-23 12G0041 1 Cover, Top

1-24 12G0176 1 Cover, Optional Paper

Asm- Index · Parts Catalog 6-5

Page 126 of the Lexmark E310 user manual — Assembly 2: Frame
Page 126 · click to enlarge
Page 126

Assembly 2: Frame

Lexmark E310 — Assembly 2: Frame diagram (page 126)
Fig. 33 · Assembly 2: Frame
Page 127 of the Lexmark E310 user manual — Assembly 2: Frame
Page 127 · click to enlarge
Page 127

Part Number Units Description

2-1 12G0099 1 Cable Asm, Printhead to HVPS

2-2 12G0046 1 Printhead Assembly E310

2-2 12G1879 1 Printhead Assembly E312

2-3 6 Screw, Type 2 PP 12G0101

2-4 13 Screw, Type 3 PP 12G0101

2-5 12G0125 1 Frame, Upper E310

2-5 12G1882 1 Frame, Upper E312

2-6 12G0047 1 Solenoid, Pick Roller Clutch E310

2-6 12G1929 1 Solenoid, Pick Roller Clutch E312

2-7 12G0128 1 Fan, Cooling

2-8 12G0059 2 Spring, Print Cartridge Lock

2-9 12G0155 1 Lock, Print CartrIdge, Right

2-10 12G0154 1 Lock, Print Cartridge, Left

2-11 12G0152 1 Housing, Cover Open Sensor E310

2-11 12G1883 1 Housing, Cover Open Sensor E312

2-12 12G0060 1 Lever, Cover Open Sensor E310

2-12 12G1881 1 Lever, Cover Open Sensor E312

2-13 12G0153 1 Spring, Cover Open Sensor

2-14 12G0045 1 Board Asm, Cover Open Sensor E310

2-14 12G1878 1 Board Asm, Cover Open Sensor E312

Asm- Index · Parts Catalog 6-7

Page 128 of the Lexmark E310 user manual — Assembly 2: Frame (continued)
Page 128 · click to enlarge
Page 128

Assembly 2: Frame (continued)

Lexmark E310 — Assembly 2: Frame (continued) diagram (page 128)
Fig. 34 · Assembly 2: Frame (continued)
Page 129 of the Lexmark E310 user manual — Assembly 2: Frame
Page 129 · click to enlarge
Page 129

Part Number Units Description

2-15 12G0048 1 Roller, Transfer

2-16 12G0057 1 LED Asm, Pre-Transfer E310

2-16 12G1887 1 LED Asm, Pre-Transfer E312

2-17 12G0049 1 Bearing Asm, Transfer Roller Right

2-18 12G0119 1 Pad Asm, Friction Left E310

2-18 12G1931 1 Pad Asm, Friction Left E312

2-19 12G0127 2 Post, Separator Asm Spring

2-20 12G0120 1 Pad Asm, Friction Right E310

2-20 12G1932 1 Pad Asm, Friction Right E312

2-21 12G0106 2 Foot, Rubber

2-22 5 Screw, Type 3 PP 12G0101

2-23 12G0050 1 Sensor Asm, Input Paper Feed/Size E310

2-23 12G1884 1 Sensor Asm, Input Paper Feed/Size E312

2-24 12G0113 1 Cable Asm, Fuser Lamp

2-25 12G0051 1 Flag, Paper Exit Sensor E310

2-25 12G1885 1 Flag, Paper Exit Sensor E312

2-26 12G0109 1 Guide, HV Contact

2-27 12G0052 1 Contact Asm, HV-Transfer Roller

2-28 12G0061 1 Cover, Fuser Lamp Wiring

2-29 12G0053 3 Contact Asm, HV-Main

2-30 12G0107 1 Cable Asm, Power Switch E310

2-30 12G1888 1 Cable Asm, Power Switch E312

2-31 12G0056 1 Frame Asm, Lower E310

2-31 12G1930 1 Frame Asm, Lower E312

2-32 12G0130 1 Cover, Pick Roller Access

2-33 12G0069 1 Bearing Asm, Transfer Roller Left

2-34 12G0058 1 Gear, Transfer Roller

Asm- Index · Parts Catalog 6-9

Page 130 of the Lexmark E310 user manual — Assembly 3: Fuser
Page 130 · click to enlarge
Page 130

Assembly 3: Fuser

Lexmark E310 — Assembly 3: Fuser diagram (page 130)
Fig. 35 · Assembly 3: Fuser
Page 132 of the Lexmark E310 user manual — Assembly 3: Fuser (continued)
Page 132 · click to enlarge
Page 132

Assembly 3: Fuser (continued)

Lexmark E310 — Assembly 3: Fuser (continued) diagram (page 132)
Fig. 36 · Assembly 3: Fuser (continued)
Page 133 of the Lexmark E310 user manual — Assembly 3: Fuser
Page 133 · click to enlarge
Page 133

Part Number Units Description

3-15 12G0172 2 Shaft, Fuser Exit Roller

3-16 12G0156 1 Roller, Fuser Exit Center

3-17 12G0076 1 Thermistor, Hot Roll E310

3-17 12G1892 1 Thermistor, Hot Roll E312

3-18 12G1942 1 Holder, Fuser Exit Center Roller

3-19 12G0078 1 Lamp, Fuser, 110 V ac E310

3-19 12G1893 1 Lamp, Fuser, 110 V ac E312

3-19 12G0124 1 Lamp, Fuser, 220 V ac E310

3-19 12G1894 1 Lamp, Fuser, 220 V ac E312

3-20 12G0082 1 Plate, Hot Roll Ground

3-21 12G0081 1 Gear, Fuser Hot Roll

3-22 12G0080 1 Bearing, Right Hot Roll

3-23 12G0083 2 Bearing Asm, Backup Roll

3-24 12G0084 1 Roller Asm, Exit Paper Feed

3-25 12G0174 3 Bushing, Exit Paper Feed Roller

3-26 12G0086 1 Roller, Backup

3-27 12G0079 1 Hot Roll, Fuser

3-28 12G0077 1 Bearing, Left Hot Roll

3-29 12G3776 1 Frame, Fuser E310

3-29 12G3777 1 Frame, Fuser E312

Asm- Index · Parts Catalog 6-13

Page 134 of the Lexmark E310 user manual — Assembly 4: Main Drive
Page 134 · click to enlarge
Page 134

Assembly 4: Main Drive

Lexmark E310 — Assembly 4: Main Drive diagram (page 134)
Fig. 37 · Assembly 4: Main Drive
Page 135 of the Lexmark E310 user manual — Assembly 4: Main Drive
Page 135 · click to enlarge
Page 135

Part Number Units Description

4-1 12G0042 1 Main Drive Assembly E310

4-1 12G1877 1 Main Drive Assembly E312

4-2 12G0044 1 Motor Asm, Main

4-3 5 Screw, Type 4 PP 12G0101

4-4 1 Gear, Drive Feed 1 PP 12G0102

4-5 1 Gear, Drive Feed 2 PP 12G0102

4-6 1 Gear, Input Paper Feed PP 12G0102

4-7 6 Screw, Type 3 PP 12G0101

4-8 1 Gear, Fuser Drive PP 12G0102

4-9 1 Gear, Idler PP 12G0102

4-10 1 Gear, OPC Drive 1 PP 12G0102

4-11 1 Gear, OPC Drive 2 PP 12G0102

Asm- Index · Parts Catalog 6-15

Page 136 of the Lexmark E310 user manual — Assembly 5: Paper Feed
Page 136 · click to enlarge
Page 136

Assembly 5: Paper Feed

Lexmark E310 — Assembly 5: Paper Feed diagram (page 136)
Fig. 38 · Assembly 5: Paper Feed
Page 137 of the Lexmark E310 user manual — Assembly 5: Paper Feed
Page 137 · click to enlarge
Page 137

Part Number Units Description

5-1 12G0063 1 Holder Asm, Spring

5-2 12G0068 1 Spring, Pad Asm, Rear

5-3 12G0062 1 Pad Asm, Pick Roller

5-4 12G0121 1 Spring, Pad Asm, Lower

5-5 12G0104 2 Spring, Separator Asm

5-6 1 Clip, E PP 12G0101

5-7 12G0065 1 Clutch Asm, Pick Roller

5-8 12G0067 1 Roller Asm, Pick E310

5-8 12G1933 1 Roller Asm, Pick E312

5-9 12G0066 1 Bearing, Left Pick Roller Shaft

5-10 12G0064 1 Separator Asm, Paper

Asm- Index · Parts Catalog 6-17

Page 138 of the Lexmark E310 user manual — Assembly 5: Paper Feed (continued)
Page 138 · click to enlarge
Page 138

Assembly 5: Paper Feed (continued)

Lexmark E310 — Assembly 5: Paper Feed (continued) diagram (page 138)
Fig. 39 · Assembly 5: Paper Feed (continued)
Page 139 of the Lexmark E310 user manual — Assembly 5: Paper Feed
Page 139 · click to enlarge
Page 139

Part Number Units Description

5-11 12G0105 1 Shaft Asm, Input Paper Feed E310

5-11 12G1934 1 Shaft Asm, Input Paper Feed E312

5-12 12G0072 2 Separator, Secondary Paper E310

5-13 12G0070 1 Roller Asm, Input Paper Feed E310

5-13 12G1889 1 Roller Asm, Input Paper Feed E312

5-14 12G0073 1 Sensor, Paper Present

5-15 12G0071 1 Flag, Paper Sensor Present

Asm- Index · Parts Catalog 6-19

Page 140 of the Lexmark E310 user manual — Assembly 6: Electronics (model E310)
Page 140 · click to enlarge
Page 140

Assembly 6: Electronics (model E310)

Lexmark E310 — Assembly 6: Electronics (model E310) diagram (page 140)
Fig. 40 · Assembly 6: Electronics (model E310)
Page 141 of the Lexmark E310 user manual — Assembly 6: Electronics (model E310)
Page 141 · click to enlarge
Page 141

Part Number Units Description

6-1 12G0087 1 Board Asm, HVPS E310

6-2 1339526 1 Power Cord, U.S., Canada, Brazil (HV)

6-2 1339517 1 Power Cord, Saudi Arabia

6-2 1339519 1 Power Cord, U.K., Ireland, Bahrain, Qatar, Oman, Jordan, Iraq, Kuwait, Yemen, Egypt, Sudan

6-2 1339520 1 Power Cord, Austria, Germany, Belgium, France, Netherlands, Norway, Spain, Spain-Catalan, Sweden, Finland, Turkey, Hungary, Greece, Czechoslovakia, Slovakia, Eastern Countries, Russia, Poland, Portugal

6-2 1339521 1 Power Cord, Israel

6-2 1339522 1 Power Cord, Switzerland

6-2 1339523 1 Power Cord, South Africa

6-2 1339525 1 Power Cord, Denmark

6-2 1342534 1 Power Cord, Chile

6-2 1342536 1 Power Cord, Argentina, Paraguay, Uruguay

6-3 12G0097 1 Cable Asm, Motor to Interconnect Board E310

6-4 12G0108 1 Bracket, Controller Board Mounting

6-5 14 Screw, Type 3 PP 12G0101

6-6 12G3786 1 Board Asm, Controller E310

6-6 12G3783 1 Board Asm, Controller E312/ 312L(model 2L1)

6-6 12G3784 1 Board Asm, Controller E312L (Model 2L2)

6-7 12G0114 1 Panel, SIMM Access

Asm- Index · Parts Catalog 6-21

Page 142 of the Lexmark E310 user manual — Assembly 6: Electronics (model E310 continued)
Page 142 · click to enlarge
Page 142

Assembly 6: Electronics (model E310 continued)

Lexmark E310 — Assembly 6: Electronics (model E310 continued) diagram (page 142)
Fig. 41 · Assembly 6: Electronics (model E310 continued)
Page 143 of the Lexmark E310 user manual — Assembly 6: Electronics (model E310)
Page 143 · click to enlarge
Page 143

Part Number Units Description

6-8 12G0095 1 Cable Asm, Engine/LVPS Board to Controller Board E310

6-9 12G0089 1 Board Asm, Engine/LVPS-110 V ac E310

6-9 12G0091 1 Board Asm, Engine/LVPS-220 V ac E310

6-10 12G0090 1 Fuse, Power Supply-110 V ac

6-10 12G0092 1 Fuse, Power Supply-220 V ac

6-11 12G0100 1 Cable Asm, Engine/LVPS Board to Interconnect Board E310

6-12 12G0088 1 Board Asm, Interconnect E310

6-13 12G1828 1 Guide, Cable E310

6-14 12G0096 1 Cable Asm, Engine/LVPS to HVPS E310

Asm- Index · Parts Catalog 6-23

Page 144 of the Lexmark E310 user manual — Assembly 6: Electronics (model E312)
Page 144 · click to enlarge
Page 144

Assembly 6: Electronics (model E312)

Lexmark E310 — Assembly 6: Electronics (model E312) diagram (page 144)
Fig. 42 · Assembly 6: Electronics (model E312)
Page 145 of the Lexmark E310 user manual — Assembly 6: Electronics (model E312)
Page 145 · click to enlarge
Page 145

Part Number Units Description

6-1 12G1896 1 Board Asm, HVPS E312

6-2 Power Cord Reference Assembly 6: Electronics (model 310) Asm/Index 6-2.

6-3 12G1940 1 Cable Asm, Motor to Engine Board E312

6-4 12G0108 1 Bracket, Controller Board Mounting

6-5 14 Screw, Type 3 PP 12G0101

6-6 12G1872 1 Board Asm, Controller E312

6-7 12G0114 1 Panel, SIMM Access

6-8 12G1926 1 Cable Asm, Engine Board to Controller Board E312

6-9 12G1941 1 Shield Asm, LVPS E312

6-10 12G1898 1 Board Asm, LVPS-110 V ac E312

6-10 12G1899 1 Board Asm, LVPS-220 V ac E312

6-11 12G0090 1 Fuse, Power Supply-110 V ac

6-11 12G0092 1 Fuse, Power Supply-220 V ac

6-12 12G1937 1 Board Asm, Engine E312

6-13 12G1927 1 Cable Asm, Engine to HVPS E312

Asm- Index · Parts Catalog 6-25

Page 146 of the Lexmark E310 user manual — Assembly 7: Options
Page 146 · click to enlarge
Page 146

Assembly 7: Options

Part Number Units Description

7 99A0517 1 SIMM, 4MB DRAM Memory

7 99A0518 1 SIMM, 8MB DRAM Memory

7 99A0519 1 SIMM, 16MB DRAM Memory

7 99A0520 1 SIMM, 32MB DRAM Memory

7 99A0724 1 SIMM, 64MB DRAM Memory

7 99A0521 1 SIMM, 1 Meg Flash Memory

7 99A0522 1 SIMM, 2 Meg Flash Memory

7 99A0523 1 SIMM, 4 Meg Flash Memory

7 99A0545 1 Adapter, External Serial

Asm- Index

Page 147 of the Lexmark E310 user manual — Assembly 8: Miscellaneous
Page 147 · click to enlarge
Page 147

Assembly 8: Miscellaneous

Part Number Units Description

8 1 Parts Packet, Fasteners PP 12G0101

3 o Screw, Type 1 (m3x10)

2 o Screw, Type 2 (m4x10)

6 o Screw, Type 3 (m3x10)

2 o Screw, Type 4 (m3x6)

1 o Clip, E

8 1 Parts Packet, Gears PP 12G0102

1 o Gear, Drive Feed 1

1 o Gear, Drive Feed 2

1 o Gear, Input Paper Feed

1 o Gear, OPC Drive 2

1 o Gear, OPC Drive 1

1 o Gear, Idler

1 o Gear, Fuser Drive

Asm- Index · Parts Catalog 6-27

Page 148 of the Lexmark E310 user manual — Assembly 8: Miscellaneous
Page 148 · click to enlarge
Page 148
Page 148 of the Lexmark E310 user manual — Assembly 8: Miscellaneous
Page 150 of the Lexmark E310 user manual — U
Page 150 · click to enlarge
Page 150

Primary User Error Message Table

2-6 Secondary User Error Message

R

Table 2-8 User Mode Print Test Page 3-3

Covers 4-2 Engine/LVPS Board (model E310)

Part Numbers

4-13 Engine/LVPS Board (model E312)

12G0021 6-3 12G0022 6-3 12G0024 6-3 12G0025 6-3 12G0027 6-3 12G0029 6-3 12G0030 6-3 12G0031 6-3 12G0032 6-3 12G0035 6-5 12G0037 6-5 12G0040 6-5 12G0041 6-5 12G0042 6-15 12G0044 6-15 12G0045 6-7 12G0046 6-7 12G0047 6-7 12G0048 6-9 12G0049 6-9 12G0050 6-9 12G0051 6-9 12G0052 6-9 12G0053 6-9 12G0056 6-9 12G0057 6-9 12G0058 6-9 12G0059 6-7 12G0060 6-7 12G0061 6-9 12G0062 6-17 12G0063 6-17 12G0064 6-17 12G0065 6-17 12G0066 6-17 12G0067 6-17 12G0068 6-17 12G0069 6-9 12G0070 6-19

4-15 Frame Assembly 4-7 Fuser Assembly 4-8 HVPS 4-10 Interconnect Board 4-12 Main Drive Assembly 4-17 Pick Roll Assembly 4-18 Printhead Assembly 4-20 Transfer Roll 4-21 Restoring Factory Defaults 3-12

S

Safety Information xv Screw Identification Table 4-2 Service Checks 2-12

Cooling Fan 2-12 Cover Open Switch 2-13 Dead Machine 2-14 Fuser 2-17 Main Motor 2-21 Operator Panel 2-23 Operator Panel Button 2-24 Paper Feed 2-24 Parallel Port 2-35 Print Quality 2-28 Service Error Codes 2-2

Primary Service Error Codes 2-2 Secondary Service Error Codes 2-5 Symptom Tables 2-10

Base Printer Symptom Table 2-10 POST Symptom Table 2-10

T

Toggle Demo/Normal Mode 3-14

U

User Error Message Table 2-6

Printer Operation 3-14 · Removals 4-2 · I-2 Service Manual

Page 151 of the Lexmark E310 user manual — Index
Page 151 · click to enlarge
Page 151

12G0071 6-19 12G0072 6-19 12G0073 6-19 12G0074 6-11 12G0075 6-11 12G0076 6-13 12G0077 6-13 12G0078 6-13 12G0079 6-13 12G0080 6-13 12G0081 6-13 12G0082 6-13 12G0083 6-13 12G0084 6-13 12G0086 6-13 12G0087 6-21 12G0088 6-23 12G0089 6-23 12G0090 6-23, 6-25 12G0091 6-23 12G0092 6-23, 6-25 12G0094 6-21 12G0095 6-23 12G0096 6-23 12G0097 6-21 12G0098 6-5 12G0099 6-7 12G0100 6-23 12G0101 6-27 12G0102 6-27 12G0103 6-11 12G0104 6-17 12G0105 6-19 12G0106 6-9 12G0107 6-9 12G0108 6-21, 6-25 12G0109 6-9 12G0112 6-3 12G0113 6-9 12G0114 6-21, 6-25 12G0119 6-9 12G0120 6-9 12G0121 6-17 12G0122 6-11 12G0123 6-11 12G0124 6-13 12G0125 6-7

12G0126 6-3 12G0127 6-9 12G0128 6-7 12G0130 6-9 12G0152 6-7 12G0153 6-7 12G0154 6-7 12G0155 6-7 12G0156 6-13 12G0157 6-11 12G0158 6-11 12G0159 6-11 12G0160 6-11 12G0161 6-11 12G0165 6-11 12G0166 6-11 12G0167 6-11 12G0171 6-11 12G0172 6-13 12G0174 6-13 12G0175 6-3 12G0176 6-5 12G0181 6-3 12G1828 6-23 12G1846 6-3 12G1847 6-5 12G1850 6-3 12G1872 6-21, 6-25 12G1874 6-3 12G1877 6-15 12G1878 6-7 12G1879 6-7 12G1881 6-7 12G1882 6-7 12G1883 6-7 12G1884 6-9 12G1885 6-9 12G1887 6-9 12G1888 6-9 12G1889 6-19 12G1891 6-11 12G1892 6-13 12G1893 6-13 12G1894 6-13 12G1896 6-25 12G1898 6-25 12G1899 6-25

Index I-3

Page 152 of the Lexmark E310 user manual — Index
Page 152 · click to enlarge
Page 152

12G1926 6-25 12G1927 6-25 12G1929 6-7 12G1930 6-9 12G1931 6-9 12G1932 6-9 12G1933 6-17 12G1934 6-19 12G1935 6-11 12G1936 6-11 12G1937 6-25 12G1938 6-5 12G1939 6-3 12G1940 6-25 12G1941 6-25 12G1942 6-13 12G3668 6-3 12G3776 6-13 12G3777 6-13 12G3972 6-3 1339517 6-21 1339519 6-21 1339520 6-21 1339521 6-21 1339522 6-21 1339523 6-21 1339525 6-21 1339526 6-21 1342534 6-21 1342536 6-21 99A0517 6-26 99A0518 6-26 99A0519 6-26 99A0520 6-26 99A0521 6-26 99A0522 6-26 99A0523 6-26 99A0545 6-26 99A0724 6-26

I-4 Service Manual

Page 153 of the Lexmark E310 user manual — Reader Comment Form Lexmark Optra E310/312 4044-XXX Service Manual P/N 12G3613 05/00
Page 153 · click to enlarge
Page 153

Reader Comment Form Lexmark Optra E310/312 4044-XXX Service Manual P/N 12G3613 05/00

You may use this form to communicate your comments about this publication, with the understanding that Lexmark may use or distribute whatever information you supply in any way it believes appropriate without incurring any obligation to you.

1. Did you find the book well organized? Yes No
2. Was the content of the book accurate and complete? Yes No
3. Was the book easy to use? Yes No
4. What can we do to improve the book?
5. What is your job title?

Questions or comments about supplies, service, applications, and so on will slow response time considerably. Please refer those questions or comments to your authorized dealer or point of purchase.

Page 154 of the Lexmark E310 user manual — FIRST CLASS MAIL PERMIT NO. 2659 LEXINGTON, KY
Page 154 · click to enlarge
Page 154

—

NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES

BUSINESS REPLY MAIL

FIRST CLASS MAIL PERMIT NO. 2659 LEXINGTON, KY

POSTAGE WILL BE PAID BY ADDRESSEE

LEXMARK INTERNATIONAL INC DEPARTMENT D22A BUILDING 035 3 740 NEW CIRCLE ROAD NW LEXINGTON KY 40511 9954

| || | ||| ||||| | || ||| || | || | || | || || |

—

Tape Please Do Not Staple Tape

Cut Along Line · Fold Here

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
The main motor, cooling fan and fuser do not come on.Go to “Cover Open Switch Service Check” on page 2-13. p.32
POST completes except one or more LEDs do not come on.Go to the“Operator Panel Service Check” on page 2-23. p.32
None of the LEDs come on.Go to the “Operator Panel Service Check” on page 2-23. p.32
Main motor does not come on.Go to the “Main Motor Service Check” on page 2-21. p.32
Fan does not come on.Go to the “Cooling Fan Service Check” on page 2-12. p.32
Fuser lamp does not come on.Go to the “Cold Fuser Service Check” on page 2-17. p.32
Fuser lamp never turns off.Go to the “Hot Fuser Service Check” on page 2-21. p.32
The paper feed picks and tries to feed paper.Go to the “Paper Feed Service Check” on page 2-24. p.32
Dead Machine (no power)Go to the “Dead Machine Service Check” on page 2-14. p.32
Fan noisy or not workingGo to the “Cooling Fan Service Check” on page 2-12. p.32
Fuser parts meltedGo to the “Hot Fuser Service Check” on page 2-21. p.32
Fuser lamp doesn’t lightGo to “Cold Fuser Service Check” on page 2-17. p.32
Toner not fused to the paperGo to “Cold Fuser Service Check” on page 2-17. p.32
Blank pageGo to “Blank page” on page 2-28. p.33
Black pageGo to “Black page” on page 2-29. p.33
Heavy backgroundGo to “Heavy background” on page 2-30. p.33
Light printGo to “Light print” on page 2-33. p.33
White or black lines or bandsGo to “White or black lines or bands” on page 2-34. p.33
Toner on back of pageGo to “Toner on back of page” on page 2-34. p.33
Incorrect characters printGo to “Incorrect characters print” on page 2-34. p.33
Paper jamsGo to “Paper Feed Service Check” on page 2-24. p.33
Main Motor noisy or does not moveGo to “Main Motor Service Check” on page 2-21. p.33
Paper never picksGo to “Paper never picks” on page 2-27. p.33
Paper feeds continuouslyGo to “Paper picks during POST and/or continuously” on page 2-25. p.33
Paper skewGo to “Paper Feed Service Check” on page 2-24. p.33
Printer not communicating with hostGo to “Parallel Port Service Check” on page 2-35. p.33
Paper wrinkled or bentGo to “Paper "trees", wrinkles, stacks poorly or curls” on page 2-28. p.33
Top cover will not closeGo to “Cover Open Switch Service Check” on page 2-13. p.33
Operator panel button does not respondGo to “Operator Panel Button Service Check” on page 2-24. p.33
Operator panel LEDs do not light or very dimGo to “Operator Panel Service Check” on page 2-23. p.33

Ask about the Lexmark E310

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lexmark E310

Be the first to ask — other owners or our team will answer.

Original document

Lexmark E310 manual PDF

154 pages·4.2 MB·Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…