
User's Guide
Machine type(s):
Model(s):
210, 230, 410, 430, 43W, 439, n01, n02, dnw, xd1, xd2, dn1, dn2, gd1, gd2, dw1, dw2, dt1, dt2, gt1, gt2



Connect the power cord to a properly grounded electrical outlet that is near the product and easily accessible.
Do not place or use this product near water or wet locations.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
Use only the power cord provided with this product or the manufacturer's authorized replacement.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a professional service person.
Safety information

SAVE THESE INSTRUCTIONS.
Safety information

Thank you for choosing this printer!
We've worked hard to make sure it will meet your needs.
To start using your new printer right away, use the setup materials that came with the printer, and then skim the User’s Guide to learn how to perform basic tasks. To get the most out of your printer, read the User’s Guide carefully, and make sure you check the latest updates on our Web site.
We're committed to delivering performance and value with our printers, and we want to make sure you're satisfied. If you do encounter any problems along the way, one of our knowledgeable support representatives will be delighted to help you get back on track fast. And if you find something we could do better, please let us know. After all, you are the reason we do what we do, and your suggestions help us do it better.
Learning about the printer

When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any options, leave enough room for them also. It is important to:
Learning about the printer


Learning about the printer


The following illustration shows a fully configured printer model with a 650-sheet duo drawer and an optional 550-sheet tray:
Learning about the printer



Learning about the printer


4 5 6 7

Learning about the printer

Installing internal options
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
You can customize your printer connectivity and memory capacity by adding optional cards. The instructions in this section explain how to install the available cards; you can also use them to locate a card for removal.
Additional printer setup

CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Remove the cover. a Turn the screws on the cover counterclockwise, and then remove them.

Additional printer setup

b Gently pull the cover away from the printer, and then remove it.

2 Use the illustration below to locate the appropriate connector.
Additional printer setup


1 Flash memory card connector
2 Memory card connector
Additional printer setup

The system board has one connector for an optional memory card.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the system board.

Additional printer setup

2 Open both latches on the connector completely.

3 Unpack the memory card.
4 Align the notches on the memory card with the ridges on the connector.
5 Push the memory card straight into the connector until it snaps into place. Make sure each latch fits over the notch located on either side of the memory card.

1 Notch · 2 Latch · Additional printer setup

6 Reinstall the system board access cover.

CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the system board.

Additional printer setup

2 Unpack the memory card.
3 Holding the card by its sides, align the plastic pins on the card with the holes on the system board. This ensures the metal pins line up correctly as well.

4 Push the card firmly into place.

1 Plastic pins · 2 Metal pins · Additional printer setup

5 Reinstall the system board cover.

The printer supports two additional input sources: an optional 550-sheet tray and a 650-sheet duo drawer (Tray 2) with an integrated multipurpose feeder.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Unpack the optional 550-sheet tray, and then remove all packing material and the dust cover.
2 Place the tray in the location chosen for the printer.
Additional printer setup

3 Align a 650-sheet duo drawer with the optional 550-sheet tray, and then lower it into place.

4 Align the printer with the 650-sheet duo drawer, and then lower the printer into place.

5 Install the dust covers.
Additional printer setup

Connect the printer to the computer using a USB cable or an Ethernet cable. A USB port requires a USB cable. Be sure to match the USB symbol on the cable with the USB symbol on the printer. Match the appropriate Ethernet cable to the Ethernet port.

Print menu settings pages to review the current menu settings and to verify if the printer options are installed correctly.
Note: If you have not made any menu item settings changes yet, then the menu settings pages list all the factory default settings. Once you select and save other settings from the menus, they replace the factory default settings as user default settings. A user default setting remains in effect until you access the menu again, choose another value, and save it.
1 Make sure that the printer is on and Ready appears.
2 From the printer control panel, press .
3 Press the arrow buttons until Reports appears, and then press .
4 Press the arrow buttons until Menu Settings Page appears, and then press .
After the menu settings pages print, Ready appears.
1 Ethernet port · 2 USB port · Additional printer setup

If the printer is attached to a network, print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 Make sure the printer is on and Ready appears.
2 From the printer control panel, press .
3 Press the arrow buttons until Reports appears, and then press .
4 Press the arrow buttons until Network Setup Page appears, and then press .
After the network setup page prints, Ready appears.
5 Check the first section on the network setup page, and confirm that Status is “Connected.”
If Status is “Not Connected,” the LAN drop may not be active, or the network cable may be malfunctioning. Consult a system support person for a solution, and then print another network setup page.
A printer driver is software that lets the computer communicate with the printer. The printer software is typically installed during the initial printer setup.
1 Close all open software programs.
2 Insert the Software and Documentation CD.
3 From the main installation dialog, click Install Printer and Software.
4 Follow the instructions on the computer screen.
1 Close all open software applications.
2 Insert the Software and Documentation CD.
3 From the Finder desktop, double-click the printer CD icon that automatically appears.
4 Double-click the Install Printer and Software icon.
5 Follow the instructions on the computer screen.
1 Go to the Lexmark Web site at www.lexmark.com.
2 From the Drivers & Downloads menu, click Driver Finder.
3 Select your printer, and then select your operating system.
4 Download the driver and install the printer software.
Additional printer setup

Once the printer software and any options are installed, it may be necessary to manually add the options in the printer driver to make them available for print jobs.
1 Open the Printers folder:
, or click Start and then click Run. b In the Start Search or Run box, type control printers.
c Press Enter, or click OK. The printer folder opens.
2 Select the printer.
3 Right-click the printer, and then select Properties.
4 Click the Install Options tab.
5 Under Available Options, add any installed hardware options.
6 Click Apply.
In Mac OS X version 10.5 or later
1 From the Apple menu, choose System Preferences.
2 Click Print & Fax.
3 Select the printer, and then click Options & Supplies.
4 Click Driver, and then add any installed hardware options.
5 Click OK.
1 From the Finder desktop, choose Go > Applications.
2 Double-click Utilities, and then double-click Print Center or Printer Setup Utility.
3 Select the printer, and then from the Printers menu, choose Show Info.
4 From the pop-up menu, choose Installable Options.
5 Add any installed hardware options, and then click Apply Changes.
a Click · Additional printer setup

Information you will need to set up the printer on a wireless network
Some ad hoc networks will also require the auto setting. Check with your system support person if you are not sure which channel to select. • Security Method—There are three basic options for Security Method: – WEP key
If your network uses more than one WEP key, enter up to four in the provided spaces. Select the key currently in use on the network by selecting the Default WEP Transmit Key. or – WPA or WPA2 passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network. – No security
If your wireless network does not use any type of security, then you will not have any security information.
If you are installing the printer on an 802.1X network using the Advanced method, then you may need the following:
Before you install the printer on a wireless network, make sure that:
Additional printer setup

1 Connect the power cable to the printer and then to a properly grounded electrical outlet, and then turn the printer on.

Make sure the printer and computer are fully on and ready.
Do not connect the USB cable until instructed to do so on the screen.
2 Insert the Software and Documentation CD.
3 Click Install Printer and Software.
4 Click Agree to agree to the License Agreement.
5 Click Suggested, and then click Next.
6 Click Wireless Network Attach.
7 Temporarily connect a USB cable between the computer on the wireless network and the printer.
Additional printer setup

8 Follow the instructions on the computer screen to complete the software installation.
9 To allow other computers on the wireless network to use the wireless printer, follow steps 2 through 6 and step 8 for each computer.
1 Locate the printer MAC address on the sheet that came with the printer. Write the last six digits of the MAC address in the space provided below:
2 Connect the power cable to the printer and then to a properly grounded electrical outlet, and then turn the printer on.

1 Access the AirPort options.
a From the Apple menu, choose System Preferences. b Click Network.
c Click AirPort.
a From the Finder desktop, choose Go > Applications. b From the Applications folder, double-click Internet Connect.
c From the toolbar, click AirPort.
2 From the Network pop-up menu, select print server xxxxxx, where the x’s are the last six digits of the MAC address located on the MAC address sheet.
3 Open the Safari browser.
4 From the Bookmarks drop-down menu, select Show.
Additional printer setup

5 Under Collections, select Bonjour or Rendezvous, and then double-click the printer name.
6 From the main page of the Embedded Web Server, navigate to the page where the wireless settings information is stored.
1 Type the name of your network (SSID) in the appropriate field.
2 Select Infrastructure as your Network Mode if you are using a wireless router.
3 Select the type of security you use to protect your wireless network.
4 Enter the security information necessary for the printer to join your wireless network.
5 Click Submit.
6 Open the AirPort application on your computer:
a From the Apple menu, choose System Preferences. b Click Network.
c Click AirPort.
a From the Finder desktop, choose Go > Applications. b From the Applications folder, double-click Internet Connect.
c From the toolbar, click AirPort.
7 From the Network pop-up menu, select your wireless network.
To print to a network printer, each Macintosh user must install a custom PostScript Printer Description (PPD) file and create a printer in the Printer Setup Utility or Print Center.
1 Install a PPD file on the computer: a Insert the Software and Documentation CD in the CD or DVD drive. b Double-click the installer package for the printer.
c From the Welcome screen, click Continue. d Click Continue again after viewing the Readme file. e Click Continue after viewing the license agreement, and then click Agree to accept the terms of the agreement.
f Select a Destination, and then click Continue. g From the Easy Install screen, click Install. h Type the user password, and then click OK.
All necessary software is installed on the computer. i Click Close when installation is complete.
Additional printer setup

1 From the Apple menu, choose System Preferences. 2 Click Print & Fax. 3 Click +. 4 Select the printer from the list. 5 Click Add.
1 From the Finder desktop, choose Go > Applications. 2 Double-click the Utilities folder. 3 Locate and double-click Printer Setup Utility or Print Center. 4 From the Printer List, choose Add. 5 Select the printer from the list. 6 Click Add. b For AppleTalk printing:
1 From the Apple menu, choose System Preferences. 2 Click Print & Fax. 3 Click +. 4 Click AppleTalk. 5 Select the printer from the list. 6 Click Add.
1 From the Finder desktop, choose Go > Applications. 2 Double-click the Utilities folder. 3 Locate and double-click Printer Setup Utility or Print Center. 4 From the Printer List, choose Add. 5 Choose the Default Browser tab. 6 Click More Printers. 7 From the first pop-up menu, choose AppleTalk. 8 From the second pop-up menu, select Local AppleTalk zone. 9 Select the printer from the list. 10 Click Add.
These instructions apply to Ethernet and fiber optic network connections.
Additional printer setup

Before you install the printer on a wired network, make sure that:
1 Insert the Software and Documentation CD.
Wait for the Welcome screen to appear.
If the CD does not launch after a minute, then do the following:
, or click Start and then click Run. b In the Start Search or Run box, type D:\setup.exe, where D is the letter of your CD or DVD drive.
2 Click Install Printer and Software.
3 Click Agree to agree to the License Agreement.
4 Select Suggested, and then click Next.
5 Select Wired Network Attach, and then click Next.
6 Select the printer manufacturer from the list.
7 Select the printer model from the list, and then click Next.
8 Select the printer from the list of printers discovered on the network, and then click Finish.
9 Follow the instructions on the computer screen to complete the installation.
1 Allow the network DHCP server to assign an IP address to the printer.
2 Print the network setup page from the printer. For information on printing a network setup page, see “Printing a network setup page” on page 24.
3 Locate the printer IP address in the TCP/IP section of the network setup page. You will need the IP address if you are configuring access for computers on a different subnet than the printer.
4 Install the drivers and add the printer. a Install a PPD file on the computer:
1 Insert the Software and Documentation CD in the CD or DVD drive. 2 Double-click the installer package for the printer. 3 From the Welcome screen, click Continue. 4 Click Continue again after viewing the Readme file. 5 Click Continue after viewing the license agreement, and then click Agree to accept the terms of the agreement. 6 Select a Destination, and then click Continue. 7 From the Easy Install screen, click Install.
a Click · Additional printer setup

8 Type the user password, and then click OK. All the necessary software is installed on the computer. 9 Click Restart when installation is complete. b Add the printer:
1 From the Apple menu, choose System Preferences. 2 Click Print & Fax. 3 Click +. 4 Click IP. 5 Type the IP address of your printer in the Address field. 6 Click Add.
1 From the Finder desktop, choose Go > Applications. 2 Double-click Utilities. 3 Double-click Printer Setup Utility or Print Center. 4 From the Printer List, click Add. 5 Click IP. 6 Type the IP address of your printer in the Address field. 7 Click Add. • For AppleTalk printing:
1 From the Apple menu, choose System Preferences. 2 Click Print & Fax. 3 Click +. 4 Click AppleTalk. 5 Select the printer from the list. 6 Click Add.
1 From the Finder desktop, choose Go > Applications. 2 Double-click Utilities. 3 Double-click Printer Setup Utility or Print Center. 4 From the Printer List, click Add. 5 Choose the Default Browser tab. 6 Click More Printers. 7 From the first pop-up menu, choose AppleTalk. 8 From the second pop-up menu, select Local AppleTalk zone.
Additional printer setup

9 Select the printer from the list. 10 Click Add.
Additional printer setup

Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impact on the environment. We design with the environment in mind, engineer our packaging to reduce materials, and provide collection and recycling programs. For more information, see:
By selecting certain printer settings or tasks, you may be able to reduce your printer's impact even further. This chapter outlines the settings and tasks that may yield a greater environmental benefit.
Studies show that as much as 80% of the carbon footprint of a printer is related to paper usage. You can significantly reduce your carbon footprint by using recycled paper and the following printing suggestions, such as printing on both sides of the paper and printing multiple pages on one side of a single sheet of paper.
For information on how you can quickly save paper and energy using one printer setting, see “Using Eco-Mode” on page 36.
As an environmentally conscientious company, Lexmark supports the use of recycled paper produced specifically for use in laser (electrophotographic) printers.
While no blanket statement can be made that all recycled paper will feed well, Lexmark consistently tests papers that represent recycled cut size copier papers available on the global market. This scientific testing is conducted with rigor and discipline. Many factors are taken into consideration both separately and as a whole, including the following:
Recycled papers are better than ever; however, the amount of recycled content in a paper affects the degree of control over foreign matter. And while recycled papers are one good path to printing in an environmentally responsible manner, they are not perfect. The energy required to de-ink and deal with additives such as colorants and “glue” often generates more carbon emissions than does normal paper production. However, using recycled papers enables better resource management overall.
Lexmark concerns itself with the responsible use of paper in general based on life cycle assessments of its products. To gain a better understanding of the impact of printers on the environment, the company commissioned a number of
Minimizing your printer's environmental impact

life cycle assessments and found that paper was identified as the primary contributor (up to 80%) of carbon emissions caused throughout the entire life of a device (from design to end-of-life). This is due to the energy-intensive manufacturing processes required to make paper.
Thus, Lexmark seeks to educate customers and partners on minimizing the impact of paper. Using recycled paper is one way. Eliminating excessive and unnecessary paper consumption is another. Lexmark is well-equipped to help customers minimize printing and copying waste. In addition, the company encourages purchasing paper from suppliers who demonstrate their commitment to sustainable forestry practices.
Lexmark does not endorse specific suppliers, although a converter’s product list for special applications is maintained. However, the following paper choice guidelines will help alleviate the environmental impact of printing:
1 Minimize paper consumption.
2 Be selective about the origin of wood fiber. Buy from suppliers who carry certifications such as the Forestry Stewardship Council (FSC) or The Program for the Endorsement of Forest Certification (PEFC). These certifications guarantee that the paper manufacturer uses wood pulp from forestry operators that employ environmentally and socially responsible forest management and restoration practices.
3 Choose the most appropriate paper for printing needs: normal 75 or 80 g/m2 certified paper, lower weight paper, or recycled paper.
Test results indicate that the following paper types are at risk for use with laser printers:
For more information about Lexmark, visit www.lexmark.com. General sustainability-related information can be found at the Environmental Sustainability link.
There are a number of ways you can reduce the amount of paper and toner you use when printing. You can:
If your printer model supports duplex printing, you can control whether print appears on one or two sides of the paper by selecting 2-sided printing from the Print dialog or the Lexmark Toolbar.
You can print up to 16 consecutive pages of a multiple-page document onto one side of a single sheet of paper by selecting a setting from the Multipage printing (N-Up) section of the Print dialog.
Minimizing your printer's environmental impact

Before printing or making multiple copies of a document:
Carefully select and load paper to avoid paper jams. For more information, see “Avoiding jams” on page 119.
Use Eco-Mode to quickly select one or more ways to reduce your printer's environmental impact.
Energy Reduce energy use, especially when the printer is idle.
Paper Duplex is enabled on printer models supporting duplex.
Energy/Paper Use all the settings associated with Energy mode and Paper mode.
Off Use factory default settings for all settings associated with Eco-Mode. This setting supports the performance specifications for your printer.
To select an Eco-Mode setting:
1 From the printer control panel, press .
2 Press the arrow buttons until Settings appears, and then press .
3 Press the arrow buttons until General Settings appears, and then press .
4 Press the arrow buttons until Eco-Mode appears, and then press .
5 Select the setting you want, and then press .
Submitting changes appears.
Use Quiet Mode to reduce the printer noise.
Minimizing your printer's environmental impact
Choose To

On Reduce printer noise.
Off Use factory default settings. This setting supports the performance specifications for your printer.
To select a Quiet Mode setting:
1 From the printer control panel, press .
2 Press the arrow buttons until Settings appears, and then press .
3 Press the arrow buttons until General Settings appears, and then press .
4 Press the arrow buttons until Quiet Mode appears, and then press .
5 Select the setting you want, and then press .
Submitting changes appears.
1 Make sure the printer is on and Ready appears.
2 From the printer control panel, press .
3 Press the arrow buttons until Settings appears, and then press .
4 Press the arrow buttons until General Settings appears, and then press .
5 Press the arrow buttons until Timeout appears, and then press .
6 Press the arrow buttons until Power Saver appears, and then press .
7 Press the arrow buttons to enter the number of minutes for the printer to wait before entering the Power Saver mode. Available settings range from 1–240 minutes.
8 Press .
Submitting changes appears.
9 Press , and then press until Ready appears.
Minimizing your printer's environmental impact
Choose To

Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information, see:
To return Lexmark products to Lexmark for recycling:
1 Visit our Web site at www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country from the list.
3 Follow the instructions on the computer screen.
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark will recycle the box.
The Lexmark Cartridge Collection Program diverts millions of Lexmark cartridges from landfills annually by making it both easy and free for Lexmark customers to return used cartridges to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. Boxes used to return the cartridges are also recycled.
To return Lexmark cartridges for reuse or recycling, follow the instructions that came with your printer or cartridge and use the pre-paid shipping label. You can also:
1 Visit our Web site at www.lexmark.com/recycle.
2 From the Toner Cartridges section, select your country from the list.
3 Follow the instructions on the computer screen.
Minimizing your printer's environmental impact

This section explains how to use the 250-sheet tray, the manual feeder, an optional 550-sheet tray and the 650-sheet duo drawer with an integrated multipurpose feeder. It also includes information about paper orientation, setting the Paper Size and Paper Type, and linking and unlinking trays.
Tray linking is useful for large print jobs or multiple copies. When one linked tray is empty, paper feeds from the next linked tray. When the Paper Size and Paper Type settings are the same for any trays, the trays are automatically linked. The Paper Size setting for all trays must be set manually from the Paper Size menu. The Paper Type setting must be set for all trays from the Paper Type menu. The Paper Type menu and the Paper Size menu are both available from the Paper Size/Type menu.
Unlinked trays have settings that are not the same as the settings of any other tray.
To unlink a tray, change the following tray settings so that they do not match the settings of any other tray:
Paper Type names describe the paper characteristics. If the name that best describes your paper is used by linked trays, assign a different Paper Type name to the tray, such as Custom Type , or define your own custom name. • Paper Size (for example: letter, A4, statement)
Load a different paper size to change the Paper Size setting for a tray. Paper Size settings are not automatic; they must be set manually from the Paper Size menu.
Assign a Custom Type name to a tray to link or unlink it. Associate the same Custom Type name to each tray that you want to link.
1 Make sure the printer is on and Ready appears.
2 From the printer control panel, press .
3 Press the arrow buttons until Paper Menu appears, and then press .
4 Press the arrow buttons until Size/Type appears, and then press .
5 Press the arrow buttons, and then press to select the tray.
The Paper Size menu appears.
6 Press the arrow buttons until the Paper Type menu appears.
Loading paper and specialty media

7 Press .
8 Press the arrow buttons until Custom Type <x> or another custom name appears, and then press .
Submitting changes appears, followed by Paper Menu.
9 Press , and then press to return to the Ready state.
1 Make sure that the printer is on and Ready appears.
2 From the printer control panel, press .
3 Press the arrow buttons until Paper Menu appears, and then press .
4 Press the arrow buttons until Size/Type appears, and then press .
5 Press the arrow buttons until the correct tray appears, and then press .
6 Press when Size appears.
7 Press the arrow buttons until the correct size appears, and then press .
Submitting changes appears, followed by Size.
8 Press the arrow buttons until Type appears, and then press .
9 Press the arrow buttons until the correct type appears, and then press .
Submitting changes appears, followed by Type.
The Universal Paper Size is a user-defined setting that lets you print on paper sizes that are not preset in the printer menus. Set the Paper Size for the specified tray to Universal when the size you want is not available from the Paper Size menu. Then, specify all of the following Universal size settings for your paper:
1 Make sure the printer is on and Ready appears.
2 From the printer control panel, press .
3 Press the arrow buttons until Paper Menu appears, and then press .
4 Press the arrow buttons until Universal Setup appears, and then press .
5 Press the arrow buttons until Units of Measure appears, and then press .
Loading paper and specialty media

6 Press the arrow buttons until the correct unit of measure appears, and then press .
Submitting changes appears, followed by the Universal Setup menu.
7 Press , and then press to return to the Ready state.
Defining a specific height and width measurement for the Universal paper size (in the portrait orientation) allows the printer to support the size, including support for standard features such as duplex printing and printing multiple pages on one sheet.
1 From the Universal Setup menu, press the arrow buttons until Portrait Width or Portrait Height appears, and then press .
2 Press the arrow buttons to decrease or increase the setting, and then press .
Submitting changes appears, followed by the Universal Setup menu.
3 Press , and then press to return to the Ready state.
The printer has one standard 250-sheet tray (Tray 1) with an attached manual feeder. The 250-sheet tray, the 650-sheet duo drawer, and the optional 550-sheet tray support the same paper sizes and types and are loaded in the same way.
1 Pull the tray out.

Loading paper and specialty media

2 Squeeze the length guide tab inward as shown, and slide the guide to the correct position for the paper size being loaded.

3 If the paper is longer than A4 or letter size, push the green tab at the back of the tray to extend it.

4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.
5 Load the paper stack with the recommended print side faceup.

Loading paper and specialty media

6 Make sure the paper guides are secure against the edges of the paper.
7 Insert the tray.

8 If a different type or size of paper was loaded than the type or size previously loaded in the tray, change the Paper Type or Paper Size setting for the tray from the printer control panel.
The 650-sheet duo drawer (Tray 2) consists of a 550-sheet tray and an integrated 100-sheet multipurpose feeder. The drawer is loaded in the same way as the 250-sheet tray and the optional 550-sheet tray, and supports the same paper types and sizes. The only differences are the look of the guide tabs and the location of the paper size indicators, as shown in the following illustration:

1 Length guide tabs
3 Width guide tabs
Loading paper and specialty media
2 Size indicators

1 Push the feeder release latch to the left to open the multipurpose feeder.

2 Grasp the extension, and pull it straight out until it is fully extended.
3 Prepare the paper for loading. • Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.
4 Locate the stack height limiter and tab.
Loading paper and specialty media


2 Stack height limiter
5 Load the paper, and then adjust the width guide to lightly touch the edge of the paper stack. • Load paper, card stock, and transparencies with the recommended print side facedown and the top edge entering first.
6 Make sure the paper is as far into the multipurpose feeder as it will go with very gentle pushing. Paper should lie flat in the multipurpose feeder. Make sure the paper fits loosely in the multipurpose feeder and is not bent or wrinkled.
Loading paper and specialty media
1 Tab · 3 Width guides · 4 Size indicators

The standard 250-sheet tray has an integrated manual feeder that can be used to print on different types of paper one sheet at a time.
1 Load one sheet of paper facedown into the center of the manual feeder.

2 Feed paper into the manual feeder only to the point where its leading edge can contact the paper guides.
3 Adjust the paper guides to the paper width.
Loading paper and specialty media


Loading paper and specialty media

Additional information for printing on speciality medias may be found in the Cardstock and Label Guide available at http://support.lexmark.com.
The following paper characteristics affect print quality and reliability. Consider these characteristics when evaluating new paper stock.
The printer can automatically feed paper weights from 60 to 176 g/m2 (16 to 47 lb bond) grain long. Paper lighter than 75 g/m2 (20 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 80 g/m2 (21 lb bond) grain long paper. For paper smaller than 182 x 257 mm (7.2 x 10.1 in.), we recommend 90 g/m2 or heavier paper.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.
Paper smoothness directly affects print quality. If paper is too rough, toner cannot fuse to it properly. If paper is too smooth, it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; however, smoothness between 150 and 200 Sheffield points produces the best print quality.
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.
Condition paper before printing by storing it in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extend the time several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60 to 176 g/m2 (16 to 47 lb bond) paper, use grain long fibers.
Paper and specialty media guidelines

Most high-quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton possesses characteristics that can negatively affect paper handling.
Using appropriate paper prevents jams and helps ensure trouble-free printing.
To help avoid jams and poor print quality:
Use these guidelines when selecting preprinted forms and letterhead:
Use papers printed with heat-resistant inks designed for use in xerographic copiers. The ink must be able to withstand temperatures up to 200°C (392°F) without melting or releasing hazardous emissions. Use inks that are not affected by the resin in toner. Inks that are oxidation-set or oil-based generally meet these requirements; latex inks might not. When in doubt, contact the paper supplier.
Preprinted papers such as letterhead must be able to withstand temperatures up to 200°C (392°F) without melting or releasing hazardous emissions.
Use these paper storage guidelines to help avoid jams and uneven print quality:
Paper and specialty media guidelines

The following tables provide information on standard and optional input sources and the sizes, types, and weights of print media they support.

Paper size Dimensions 250-sheet tray Optional 550-sheet tray Multipurpose feeder
A4 210 x 297 mm (8.3 x 11.7 in.)
A5 148 x 210 mm (5.83 x 8.3 in.)
JIS B5 182 x 257 mm (7.2 x 10.1 in.)
A6 105 x 148 mm (4.1 x 5.8 in.)
Statement 140 x 216 mm (5.5 x 8.5 in.)
Letter 216 x 279 mm (8.5 x 11 in.)
Folio 216 x 330 mm (8.5 x 13 in.)
Oficio (Mexico) 216 x 340 mm (8.5 x 13 in.)
Legal 216 x 356 mm (8.5 x 14 in.)
Executive 184 x 267 mm (7.3 x 10.5 in.)
* When Universal is selected, the page is formatted for 216 x 356 mm (8.5 x 14 in.) unless the size is specified by the software program.
Paper and specialty media guidelines


Paper size Dimensions 250-sheet tray Optional 550-sheet tray Multipurpose feeder
Universal* 148 x 210 mm (5.8 x 8.3 in.) up to 216 x 356 mm (8.5 x 14 in.)
76 x 127 mm (3 x 5 in.) up to 216 x 356 mm (8.5 x 14 in.)
9 Envelope 98 x 225 mm (3.9 x 8.9 in.)
10 Envelope 105 x 241 mm (4.1 x 9.5 in.)
DL Envelope 110 x 220 mm (4.3 x 8.7 in.)
B5 Envelope 176 x 250 mm (6.9 x 9.8 in.)
C5 Envelope 162 x 229 mm (6.4 x 9 in.)
Monarch 105 x 241 mm (4.1 x 9.5 in.)
Other Envelope 98 x 162 mm (3.9 x 6.3 in.) up to 176 x 250 mm (6.9 x 9.8 in.)
* When Universal is selected, the page is formatted for 216 x 356 mm (8.5 x 14 in.) unless the size is specified by the software program.
Paper and specialty media guidelines


* Lexmark transparency part numbers 12A8240 and 12A8241 are supported from the standard tray, the manual feeder, and the multipurpose feeder.
Paper type 250-sheet tray Optional 550-sheet tray
Multipurpose feeder Manual feeder
Light1, 2 60 to 74.9 g/m2 grain long (16 to 19.9 lb bond)
60 to 74.9 g/m2 grain long (16 to 19.9 lb bond)
60 to 74.9 g/m2 grain long (16 to 19.9 lb bond)
60 to 74.9 g/m2 grain long (16 to 19.9 lb bond)
Plain1, 2 75 to 89.9 g/m2 grain long (20 to 23.8 lb bond)
75 to 89.9 g/m2 grain long (20 to 23.8 lb bond)
75 to 89.9 g/m2 grain long (20 to 23.8 lb bond)
75 to 89.9 g/m2 grain long (20 to 23.8 lb bond)
Heavy1, 2 90 to 104.9 g/m2 grain long (23.9 to 27.8 lb bond)
90 to 104.9 g/m2 grain long (23.9 to 27.8 lb bond)
90 to 104.9 g/m2 grain long (23.9 to 27.8 lb bond)
90 to 104.9 g/m2 grain long (23.9 to 27.8 lb bond)
Cardstock1, 2 105 to 176 g/m2 grain long (27.8 to 47 lb bond)
105 to 176 g/m2 grain long (27.8 to 47 lb bond)
105 to 176 g/m2 grain long (27.8 to 47 lb bond)
105 to 176 g/m2 grain long (27.8 to 47 lb bond)
1 Paper types must be set to match the supporting paper weights.
2 The duplex supports paper weights between 60–105 g/m2 (16–28 lb) grain long bond. The duplex does not support card stock, transparencies, envelopes, or labels.
3 For 60 to 176 g/m2 (16 to 47 lb bond) paper, we recommend grain long fibers.
4 Lexmark transparency part numbers 12A8240 and 12A8241 are supported from the 250-sheet tray, manual feeder, and multipurpose feeder.
5 The pressure sensitive area must enter the printer first.
6 100 percent cotton content maximum weight is 90 g/m2 (24 lb) bond.
7 105 g/m2 (28 lb) bond envelopes are limited to 25 percent cotton content.
Paper and specialty media guidelines

Paper type 250-sheet tray Optional 550-sheet tray
Multipurpose feeder Manual feeder
Glossy papers Book—88 to 176 g/m2
Book—88 to 176 g/m2
Book—88 to 176 g/m2
Book—88 to 176 g/m2
grain long (60 to 120 lb book)
grain long (60 to 120 lb book)
grain long (60 to 120 lb book)
grain long (60 to 120 lb book)
Cover—162 to 176 g/m2 grain long (60 to 65 lb cover)
Cover—162 to 176 g/m2 grain long (60 to 65 lb cover)
Cover—162 to 176 g/m2 grain long (60 to 65 lb cover)
Cover—162 to 176 g/m2 grain long (60 to 65 lb cover)
Card stock—maximum (grain long)3
Index Bristol— 120 g/m2 (67 lb)
Index Bristol— 120 g/m2 (67 lb)
Index Bristol— 120 g/m2 (67 lb)
Index Bristol— 120 g/m2 (67 lb)
Tag—120 g/m2 (74 lb)
Tag—120 g/m2 (74 lb)
Tag—120 g/m2 (74 lb)
Tag—120 g/m2 (74 lb)
Cover—135 g/m2
Cover—135 g/m2
Cover—135 g/m2
Cover—135 g/m2
Card stock—maximum (grain short)1
Index Bristol— 163 g/m2 (90 lb)
Index Bristol— 163 g/m2 (90 lb)
Index Bristol— 163 g/m2 (90 lb)
Index Bristol— 163 g/m2 (90 lb)
Tag—163 g/m2 (100 lb)
Tag—163 g/m2 (100 lb)
Tag—163 g/m2 (100 lb)
Tag—163 g/m2 (100 lb)
Cover—176 g/m2
Cover—176 g/m2
Cover—176 g/m2
Cover—176 g/m2
Transparencies4 170–180 g/m2 (45 to 48 lb) N/A 170–180 g/m2 (45 to 48 lb) 170–180 g/m2 (45 to 48 lb)
Labels—maximum5 Paper—131 g/m2
Paper—131 g/m2 (35 lb bond)
Paper—131 g/m2
Paper—131 g/m2
Envelopes6,7 X X 60 to 105 g/m2 (16 to 28 lb bond) 60 to 105 g/m2 (16 to 28 lb bond)
1 Paper types must be set to match the supporting paper weights.
2 The duplex supports paper weights between 60–105 g/m2 (16–28 lb) grain long bond. The duplex does not support card stock, transparencies, envelopes, or labels.
3 For 60 to 176 g/m2 (16 to 47 lb bond) paper, we recommend grain long fibers.
4 Lexmark transparency part numbers 12A8240 and 12A8241 are supported from the 250-sheet tray, manual feeder, and multipurpose feeder.
5 The pressure sensitive area must enter the printer first.
6 100 percent cotton content maximum weight is 90 g/m2 (24 lb) bond.
7 105 g/m2 (28 lb) bond envelopes are limited to 25 percent cotton content.
Paper and specialty media guidelines

Paper type 250-sheet tray Optional 550-sheet tray Multipurpose tray
Paper 250 sheets1 550 sheets1 100 sheets1
Labels 1002 2002 502
Transparencies 50 X 50
Envelopes X X 10
Other X X Various quantities3
1 Based on 75 g/m2 (20 lb) paper
2 Capacity varies depending on label material and construction.
3 Capacity varies depending on the weight and type of paper.
Paper type Standard output bin1
Paper 100 sheets2
1 Capacity may vary depending on media specifications and the printer operating environment.
2 Based on 75 g/m2 (20 lb) paper
Paper and specialty media guidelines

Printing a document
1 Load paper into a tray or feeder.
2 From the printer control panel Paper menu, set the Paper Size/Type to match the loaded paper.
3 Send the print job:
a With a document open, click File Print. b Click Properties, Preferences, Options, or Setup, and then adjust the settings as needed.
a Customize the settings as needed in the Page Setup dialog:
1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the loaded paper. 3 Click OK. b Customize the settings as needed in the Print dialog:
1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options. 2 From the Print dialog and pop-up menus, adjust the settings as needed.
Printing

Additional information for printing on speciality medias may be found in the Cardstock and Label Guide available on http://support.lexmark.com.
Page orientation is important when printing on letterhead. Use the following table to determine which direction to load the letterhead:

Printed letterhead design is placed faceup. The top edge of the sheet with the logo is placed at the front of the tray.
Printed letterhead design is placed facedown. The top edge of the sheet with the logo is placed at the back of the tray.
Printing


Preprinted letterhead design is placed facedown. The top edge of the sheet with the logo should enter the manual feeder first.
Preprinted letterhead design is placed faceup. The top edge of the sheet with the logo should enter the manual feeder last.
Print samples on the transparencies being considered for use before buying large quantities.
When printing on transparencies:
Printing

Print samples on the envelopes being considered for use before buying large quantities.
When printing on envelopes:
Print samples on the labels being considered for use before buying large quantities.
For detailed information on label printing, characteristics, and design, see the Card Stock & Label Guide available on the Lexmark Web site at http://support.lexmark.com.
When printing on labels:
releasing hazardous emissions.
Printing

Card stock is heavy, single-ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly impact print quality. Print samples on the card stock being considered for use before buying large quantities.
When printing on card stock:
Printing

A USB port is located on the printer control panel of some models. Insert a flash drive to print supported file types. Supported file types include: .pdf, .gif, .jpeg, .jpg, .bmp, .png, .tiff, .tif, .pcx, and .dcx.
Many flash drives are tested and approved for use with the printer. For more information, visit the Lexmark Web site at www.lexmark.com.
1 Make sure the printer is on and Ready or Busy appears.
2 Insert a flash drive into the USB port.
3 Press the arrow buttons until the document you want to print appears, and then press .
4 Press to print one copy, or enter the number of copies using the arrow buttons, and then press to initiate the print job.
Printing

1 Insert one end of the USB cable into the camera.
2 Insert the other end of the USB cable into the USB port on the front of the printer.
3 Follow the instructions on the camera to select and print photos.
1 Make sure the printer is on and Ready appears.
2 From the printer control panel, press .
3 Press the arrow buttons until Reports appears, and then press .
4 Press the arrow buttons until Print Fonts appears, and then press .
5 Press the arrow buttons until PCL Fonts or PostScript Fonts appears, and then press .
After the font sample list prints, Ready appears.
Printing

A directory list shows the resources stored in flash memory.
1 Make sure the printer is on and Ready appears.
2 From the printer control panel, press .
3 Press the arrow buttons until Reports appears, and then press .
4 Press the arrow buttons until Print Directory appears, and then press .
After the directory list prints, Ready appears.
Print the print quality test pages to isolate print quality problems.
1 Turn the printer off.
2 Hold down and while turning the printer on.
3 Release the buttons when the dots appear, and then wait for Config Menu to appear.
4 Press the arrow buttons until Prt Quality Pgs appears, and then press .
The print quality test pages print.
5 Press the arrow buttons until Exit Config Menu appears, and then press .
Ready appears.
1 Press .
Stopping appears, followed by Cancel Print Job.
2 Press .
Canceling appears, followed by Ready.
, or click Start and then click Run. b In the Start Search or Run box, type control printers.
c Press Enter, or click OK. The printers folder opens.
2 Double-click the printer icon.
Printing

3 Select the job to cancel.
4 From the keyboard, press Delete.
From the Windows taskbar:
When you send a job to print, a small printer icon appears in the right corner of the taskbar.
1 Double-click the printer icon.
A list of print jobs appears in the printer window.
2 Select a job to cancel.
3 From the keyboard, press Delete.
In Mac OS X version 10.5 or later:
1 From the Apple menu, choose System Preferences.
2 Click Print & Fax, and then double-click the printer icon.
3 From the printer window, select the job to cancel.
4 From the icon bar at the top of the window, click the Delete icon.
In Mac OS X version 10.4 and earlier:
1 From the Go menu, choose Applications.
2 Double-click Utilities, and then double-click Printer Setup Utility or Print Center.
3 Double-click the printer icon.
4 From the printer window, select the job to cancel.
5 From the icon bar at the top of the window, click the Delete icon.
Printing

Menus list
Supplies Menu Paper Menu Reports Network/Ports Settings
Yellow Cartridge Black Cartridge
Paper Texture Paper Weight
Network Setup Page Print Fonts
USB Menu Wireless Menu
Finishing Menu Quality Menu
Cyan, Magenta, Yellow, or Black Toner Cartridges
Shows the status of the toner cartridges
Early Warning Low Invalid Replace Missing or Defective OK Unsupported
Shows the status of the imaging kit
OK Replace Black Imaging Kit Replace Color Imaging Kit Defective
Shows the status of the waste toner box
Near Full Replace Missing OK

Sets a default paper source for all print jobs
Tray MP Feeder Manual Paper Manual Env
Specifies the paper size loaded in each tray
A4 A5 JIS B5 Letter Folio Oficio (Mexico) Legal Executive Universal

Specifies the type of paper loaded in each tray
Plain Paper Glossy Paper Card Stock Transparency Recycled Letterhead Colored Paper Labels Bond Preprinted Light Paper Heavy Paper Rough/Cotton Custom Type
Specifies the paper size loaded in the multipurpose feeder
A4 A5 JIS B5 A6 Statement Letter Folio Oficio (Mexico) Legal Executive Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope B5 Envelope C5 Envelope Other Envelope

Specifies the type of paper loaded in the multipurpose feeder
Plain Paper Glossy Paper Card Stock Transparency Recycled Letterhead Colored Paper Labels Bond Envelope Preprinted Light Paper Heavy Paper Rough/Cotton Custom Type
Specifies the size of the paper being manually loaded
A4 A5 JIS B5 A6 Statement Letter Folio Oficio (Mexico) Legal Executive Universal
Specifies the type of paper being manually loaded
Plain Paper Glossy Paper Card Stock Transparency Recycled Letterhead Colored Paper Labels Bond Preprinted Light Paper Heavy Paper Rough/Cotton Custom Type

Specifies the size of the envelope being manually loaded
7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope B5 Envelope C5 Envelope Other Envelope
Specifies the type of envelope being manually loaded
Envelope Custom Type
Specifies the relative texture of the paper loaded
Specifies the relative texture of the card stock loaded
Specifies the relative texture of the transparencies loaded
Specifies the relative texture of the recycled paper loaded
Specifies the relative texture of the glossy paper loaded
Specifies the relative texture of the labels loaded

Specifies the relative texture of the paper loaded
Specifies the relative texture of the envelopes loaded
Specifies the relative texture of the paper loaded
Specifies the relative texture of the paper loaded
Specifies the relative texture of the colored paper loaded
Specifies the relative texture of the light paper loaded
Specifies the relative texture of the heavy paper loaded
Specifies the relative texture of the rough/cotton paper loaded
Specifies the relative texture of the custom paper loaded

Plain Weight, Glossy Weight, Bond Weight, Letterhead Weight, Preprinted Weight, or Colored Weight
Identifies the relative weight of the paper loaded
Identifies the relative weight of the transparencies loaded
Identifies the relative weight of the recycled paper loaded
Identifies the relative weight of the labels loaded
Identifies the relative weight of the envelopes loaded
Identifies the relative weight of the card stock loaded
Identifies the relative weight of the light paper loaded
Identifies the relative weight of the heavy paper loaded

Identifies the relative weight of the rough/cotton paper loaded
Identifies the relative weight of the custom paper type loaded
Determines the paper loading direction for all jobs that specify Recycled as the paper type
Determines the paper loading direction for all jobs that specify glossy as the paper type
Determines the paper loading direction for all jobs that specify Bond as the paper type
Determines the paper loading direction for all jobs that specify Letterhead as the paper type
Determines the paper loading direction for all jobs that specify Preprinted as the paper type
Determines the paper loading direction for all jobs that specify Colored as the paper type
Determines the paper loading direction for all jobs that specify Light Paper as the paper type

Determines the paper loading direction for all jobs that specify Heavy Paper as the paper type
Determines the paper loading direction for all jobs that specify Rough/Cotton as the paper type
Determines the paper loading direction for all jobs that specify Custom as the paper type
Associates a paper or specialty media type with a factory default Custom Type <x> name or a user-defined Custom Name created from the Embedded Web Server or MarkVisionTM Professional. This user-defined name displays instead of Custom Type <x>.
Paper Card Stock Transparency Glossy Labels Envelope Rough/Cotton
Specifies a paper type when the Recycled setting is selected in other menus
Paper Card Stock Transparency Glossy Labels Envelope Rough/Cotton

Identifies the units of measure
Sets the portrait width
3–14.17 inches 76–360 mm
Sets the portrait height
3–14.17 inches 76–360 mm
Specifies the feed direction
Short Edge Long Edge
Menu Settings Page Prints a report containing information about paper loaded into trays, installed memory, the total page count, alarms, timeouts, the printer control panel language, the TCP/IP address, the status of supplies, the status of the network connection, and other information

Device Statistics Prints a report containing printer statistics such as supply information and details about printed pages
Network Setup Page Prints a report containing information about the network settings, such as TCP/IP address information
Prints a report of all the fonts available for the printer language currently set in the printer
PCL Fonts PostScript Fonts
Print Defects Prints a diagnostic list of problems
Asset Report Prints a report containing asset information including the printer serial number and model name. The report contains text and UPC bar codes that can be scanned into an asset database.

Shows the print server
Auto
Sets the printer to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language
Sets the printer to automatically switch to PostScript emulation when a print job requires it, regardless of the default printer language
Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol
Sets the size of the network input buffer

Sets the printer to process Macintosh binary PostScript print jobs
Sets printer settings on jobs sent through a network port
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
This menu is available from the Network/Ports menu:
Network/Ports Network Menu Reports
Print Setup Page Prints a report containing information about the current network setup
This menu is available from the Network/Ports menu:
Network/Ports Network Menu Network Card
Lets you view the connection status of the network card
View Card Speed Lets you view the speed of a currently active network card
Lets you view the network addresses
Sets the amount of time in seconds that a network print job can take before it is canceled

Allows the printer to print a banner page
This menu is available from the Network/Ports menu:
Network/Ports Network Menu TCP/IP
View Hostname Lets you view the current TCP/IP hostname
IP Address Lets you view or change the current TCP/IP Address
Netmask Lets you view or change the current TCP/IP Netmask
Gateway Lets you view or change the current TCP/IP Gateway
Specifies the DHCP address and parameter assignment setting
Specifies the Zero Configuration Networking setting
Enables the built-in FTP server, which allows you to send files to the printer using the File Transfer Protocol.
Enables the built-in Web server (Embedded Web Server). When enabled, the printer can be monitored and managed remotely using a Web browser.
WINS Server Address Lets you view or change the current WINS Server Address
Lets you view or change the current DDNS/mDNS Server Address
DNS Server Address Lets you view or change the current DNS Server Address

This menu is available from the Network/Ports menu:
Network/Ports Network Menu IPv6
Enables IPv6 in the printer
Specifies whether the network adapter accepts the automatic IPv6 address configuration entries provided by a router
Lets you view the current setting
Enables DHCPv6 in the printer
Use the following menu items to view or configure the wireless internal print server settings.
This menu is available from the Network/Ports menu:
Network/Ports Network Menu Wireless
Specifies the network mode
Specifies the wireless standard for the wireless network
802.11b/g/n 802.11n 802.11b/g
Lets you select an available network for the printer to use

View Signal Quality Lets you view the quality of the wireless connection
View Security Mode Lets you view the encryption method for the wireless connection
This menu is available from the Network/Ports menu:
Network/Ports Network Menu AppleTalk
View Name Shows the assigned AppleTalk name
View Address Shows the assigned AppleTalk address
Provides a list of AppleTalk zones available on the network
Sets the printer to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language
Sets the printer to automatically switch to PostScript emulation when a print job requires it, regardless of the default printer language

Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol
Sets the size of the USB input buffer
Sets the printer to process Macintosh binary PostScript print jobs
Sets the network address, netmask, or gateway information for an external print server that is attached to the printer using a USB cable
ENA Address ENA Netmask ENA Gateway

Sets the language of the text appearing on the display
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portugues Suomi Russian Polski Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese
Minimizes the use of energy, paper, or specialty media
Off Energy Energy/Paper Paper
Reduces the amount of noise produced by the printer

Instructs the printer to run the setup wizard
Sets an alarm to sound when the printer requires operator intervention
Available selections are:
Specifies the number of minutes of inactivity before some systems begin entering a minimum power state
Sets the amount of time in seconds the printer waits before returning the printer display to a Ready state
Sets the amount of time in seconds the printer waits to receive an end-of-job message before canceling the remainder of the print job
Sets the amount of time in seconds the printer waits for additional data before canceling a print job
Lets the printer automatically continue printing from certain offline situations when not resolved within the specified time period

Specifies whether the printer reprints jammed pages
Lets the printer successfully print a page that may not have printed otherwise
Returns the printer settings to the factory default settings
Do Not Restore Restore
Sets the default printer language
PCL Emulation PS Emulation PPDS Emulation
Sets the logical and physical printable area
Normal Fit to Page Whole Page

Sets the storage location for downloads
Specifies how the printer handles temporary downloads, such as fonts and macros stored in RAM, when the printer receives a job that requires more memory than is available
Specifies whether duplex (2-sided) printing is set as the default for all print jobs
1 sided 2 sided
Defines the way duplexed pages are bound and how the printing on the back of the page is oriented in relation to the printing on the front of the page
Long Edge Short Edge
1–999 Specifies a default number of copies for each print job

Specifies whether blank pages are inserted in a print job
Do Not Print Print
Stacks the pages of a print job in sequence when printing multiple copies
Off (1,1,1,2,2,2) On (1,2,1,2,1,2)
Specifies whether blank separator sheets are inserted
None Between Copies Between Jobs Between Pages
Specifies the paper source for separator sheets
Tray MP Feeder
Specifies that multiple-page images be printed on one side of a sheet of paper
Off 2-Up 3-Up 4-Up 6-Up 9-Up 12-Up 16-Up
Specifies the positioning of multiple-page images when using N-up (pages-sides)
Horizontal Reverse Horizontal Reverse Vertical Vertical

Specifies the orientation of a multiple-page sheet
Prints a border around each page image when using N-up (pages-sides)
Adjusts the color output on the printed page
Specifies the printed output resolution
4800 CQ 1200 dpi
1–5 Lightens or darkens the printed output
Enables a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts

Reduces the amount of toner used for graphics and images. The amount of toner used for text is not reduced.
Adjusts brightness in color outputs
0–5 Adjusts contrast in color outputs
0–5 Adjusts saturation in color outputs
Adjusts color in printed output by increasing or decreasing the amount of toner used for each color
Cyan Magenta Yellow Black
Restores the Color Balance factory default settings
Prints sample pages for each of the RGB and CMYK color conversion tables used in the printer
sRGB Display sRGB Vivid Display—True Black Vivid Off—RGB US CMYK Euro CMYK Vivid CMYK Off—CMYK

Customizes the RGB color conversions
RGB Image RGB Text RGB Graphics
Available selections for each setting are:
Vivid sRGB Display Display—True Black sRGB Vivid Off
Customizes the CMYK color conversions
CMYK Image CMYK Text CMYK Graphics
Available selections for each setting are:
US CMYK Euro CMYK Vivid CMYK Off
Color Adjust Initiates an automatic color adjust calibration

Formats the flash memory. Flash memory refers to the memory added by installing an optional flash memory card in the printer.
Prepares the flash memory to receive new data by retrieving lost storage space
Assists in isolating the source of a print job problem
Provides an estimate of the percentage coverage of cyan, magenta, yellow, and black toner on a page. The estimate is printed on a separator page.
Scales page content to fit the selected paper size

Prints annotations in a PDF
Do Not Print Print
Prints a page containing the PostScript error
Establishes the font search order
Enhances the contrast and sharpness of low-resolution images and smooths their color transitions
Specifies the set of fonts used by the Font Name menu item
Resident Download Flash All

Identifies a specific font and the option where it is stored
Specifies the symbol set for each font name
Changes the point size for scalable typographic fonts
1.00–1008.00
Specifies the font pitch for scalable monospaced fonts
0.08–100
Specifies the orientation of text and graphics on the page
Specifies the number of lines that print on each page

Sets the printer to print on A4-size paper
198 mm 203 mm
Specifies whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command
Auto CR after LF
Specifies whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command
Auto LF after CR
Configures the printer to work with printer software or programs that use different source assignments for trays, drawers, and feeders
Assign MP Feeder Assign Tray Assign Manual Paper Assign Man Env
Available selections for each setting are:
Displays the factory default setting assigned to each tray, drawer, or feeder
Returns all tray, drawer, and feeder assignments to the factory default settings

Selects the optimal paper size, scaling, and orientation
Inverts bi-tonal monochrome images
Scales the image to fit the selected paper size
Best Fit Anchor Top Left Anchor Center Fit Height/Width Fit Height Fit Width
Sets the image orientation
Portrait Landscape Rev Portrait Rev Landscape
Controls the size of each photo printed from a PictBridge-enabled digital camera
Auto L 2L Hagaki Postcard Card Size 100 x 150 mm 4 x 6 in 8 x 10 in Letter A4 A5 JIS B5

Determines the maximum number of images that can be printed on one side of the paper
Auto Off 2 Up 3 Up 4 Up 6 Up 9 Up 12 Up 16 Up Index Print
Determines which resolution, toner darkness, and color saver values the printer uses when printing photos sent from a PictBridge-enabled digital camera
Identifies the printer default input source when printing photos from a PictBridge-enabled digital camera
Manual Paper MP Feeder Tray
Enables or disables the USB port on the front of the printer
Enables or disables the ability of the flash drive to update the firmware code by way of a USB device
1–999 Sets the number of copies the printer should produce for each page contained in a print job
Controls whether the printer prints on one side or both sides of the paper
1 sided 2 sided

Periodically, certain tasks are required to maintain optimum print quality.
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:
A message appears on the display when a replacement supply item is needed or when maintenance is required.
You can check the status of printer supplies by printing a menu settings page:
1 Make sure the printer is on and Ready appears.
2 From the printer control panel, press .
3 Press the arrow buttons until Reports appears, and then press .
4 Press the arrow buttons until Menu Settings Page appears, and then press .
1 Type the printer IP address into the address field of your Web browser.
2 Click Device Status. The Device Status page appears, displaying a summary of supply levels.
Maintaining the printer

To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, visit the Lexmark Web Site at www.lexmark.com or contact the place where you purchased the printer.
When 88 Cyan Cartridge Low, 88 Magenta Cartridge Low, 88 Yellow Cartridge Low, or 88 Black Cartridge low appears, order a new cartridge.
When 88 Replace Cyan Cartridge, 88 Replace Magenta Cartridge, 88 Replace Yellow Cartridge, or 88 Replace Black Cartridge appears, you must replace the specified toner cartridge.

Part name Part number C540 and C543 C544 C546
Maintaining the printer


Part name Part number C540 and C543 C544 C546
When Replace black and color imaging kit or Replace black imaging kit appears, order a replacement imaging kit.

Maintaining the printer

When 82 Replace Waste Toner appears, order a replacement waste toner box. The waste toner box must be replaced when 82 Replace Waste Toner appears.
Part name Part number
Waste toner bottle C540X75G
Replace the waste toner box when 82 Replace waste toner appears. The printer will not continue printing until the waste toner box is replaced.

2 Waste toner box
3 Right side cover
1 Top door · 4 Front door · Maintaining the printer

1 Unpack the replacement waste toner box.
2 Grasp the front door at the sides, and then pull it toward you.

3 Open the top door by sliding the button forward.

4 Remove the right side cover.

Maintaining the printer

5 Press the green levers on each side of the waste toner box, and then remove it.

6 Place the waste toner box in the enclosed packaging.
For more information, see “Recycling Lexmark products” on page 38.
7 Insert the new waste toner box.

8 Replace the right side cover.

Maintaining the printer

9 Close the top door.

10 Close the front door.

Replace the black and color imaging kit when 31.yy Defective Imaging Kit appears.
1 Grasp the front door at the sides, and then pull it toward you.

Maintaining the printer

2 Open the top door by sliding the button forward.

3 Remove the toner cartridges by lifting the handles, and then gently pulling them away from the imaging kit.

4 Remove the right side cover.

Maintaining the printer

5 Press the green levers on each side of the waste toner box, and then remove it.

6 Lift the blue levers on the imaging kit, and then pull it toward you.

7 Press down on the blue levers, grasp the green handles on the sides, and then pull the imaging kit out.

Maintaining the printer

8 Remove the yellow, cyan, magenta, and black developer units.

9 Unpack the replacement black and color imaging kit, and leave the packaging on the developer units.
10 Gently shake the yellow, cyan, magenta, and black developer units side to side.
11 Remove the packaging from the developer units.
12 Insert the yellow, cyan, magenta, and black developer units.

13 Place the used black and color imaging kit in the enclosed package.
For more information, see “Recycling Lexmark products” on page 38.
Maintaining the printer

14 Align and insert the imaging kit.

15 Gently, but firmly push the blue levers down until the imaging kit drops into place.

16 Replace the waste toner box.

Maintaining the printer

17 Replace the right side cover.

18 Replace the toner cartridges.

19 Close the top door.

Maintaining the printer

20 Close the front door.

Replace the specified toner cartridge (yellow, cyan, magenta, or black) when 88 Replace <color> Cartridge appears. The printer will not continue printing until the specified cartridge is replaced.
1 Make sure the printer is on and Ready or 88 Replace <color> Cartridge appears.
2 Unpack the new cartridge, and then set it near the printer.
3 Open the top door by sliding the button forward.

Maintaining the printer

4 Remove the toner cartridge by lifting the handle, and then gently pulling it away from the imaging kit.

5 Align the new toner cartridge, and then press down until it clicks into place.

Maintaining the printer

6 Close the top door.

Replace a developer unit when a print quality defect occurs.
1 Grasp the front door at the sides, and then pull it toward you.

2 Open the top door by sliding the button forward.

Maintaining the printer

3 Remove the toner cartridges by lifting the handles and then gently pulling them away from the imaging kit.

4 Remove the right side cover.

5 Press the green levers on each side of the waste toner bottle, and then remove it.

Maintaining the printer

6 Lift the blue levers on the imaging kit, and then pull it toward you.

7 Press down on the blue levers, grasp the handles on the sides, and then pull the imaging kit out.

8 Remove the used developer unit.

9 Place the used developer unit in the enclosed package.
For more information, see “Recycling Lexmark products” on page 38.
10 Unpack the replacement developer unit, and leave the packaging on.
11 Gently shake the developer unit from side to side.
Maintaining the printer

12 Remove the red shipping cover from the developer unit.

13 Insert the developer unit.

14 Align and insert the imaging kit.

Maintaining the printer

15 Gently, but firmly push the blue levers down until the imaging kit drops into place.

16 Replace the waste toner box.

17 Replace the right side cover.

Maintaining the printer

18 Replace the toner cartridges.

19 Close the top door.

20 Close the front door.

1 Make sure that the printer is turned off and unplugged from the wall outlet.
2 Remove paper from the standard exit tray.
3 Dampen a clean, lint-free cloth with water.
Maintaining the printer

4 Wipe only the outside of the printer, making sure to include the standard exit tray.
5 Make sure the standard exit tray is dry before beginning a new print job.
21 kg (46.2 lbs.)
The printer and options can be safely moved to another location by following these precautions:
When shipping the printer, use the original packaging or call the place of purchase for a relocation kit.
Maintaining the printer

Restoring the factory default settings
Menu settings marked with an asterisk (*) indicate the active settings. You can restore the original printer settings, often referred to as the factory default settings. If you want to retain a list of the current menu settings for reference, then print a menu settings page before you restore the factory default settings.
1 Make sure the printer is on and Ready appears.
2 From the printer control panel, press .
3 Press the arrow buttons until Settings appears, and then press .
4 Press the arrow buttons until General Settings appears, and then press .
5 Press the arrow buttons until Factory Defaults appears, and then press .
6 Press the arrow buttons until Restore Now appears, and then press .
Submitting changes appears briefly.
7 Press , and then press until Ready appears.
If the printer is installed on a network, the Embedded Web Server is available for a range of functions:
To access the Embedded Web Server:
1 Type the printer IP address into the address field of your Web browser.
2 Click one of the tabs to access information about the printer, change settings, or view a report.
Administrative support

You can have the printer send you an e-mail when the supplies are getting low or when the paper needs to be changed, added, or unjammed.
To set up e-mail alerts:
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Under Other Settings, click E-mail Alert Setup.
4 Select the items for notification and type in the e-mail addresses that you want to receive e-mail alerts.
5 Click Submit.
You can determine how you would like to be notified when supplies run low or reach their end-of-life.
To configure supply notifications using the Embedded Web Server:
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Click Print Settings.
4 Click Supply Notifications.
5 From the drop-down box for each supply, select among the options for notification. Explanations for each option are provided.
6 Click Submit to save your selections.
Using the Embedded Web Server, you can copy printer settings to up to 15 other network printers. To copy printer settings:
1 Type the printer IP address into the address field of your Web browser.
2 Click Copy Printer Settings.
3 To change the language, select a language from the drop-down list, and then click Click here to submit language.
4 Click Printer Settings.
Administrative support

5 Enter the IP addresses of the source and target printers.
6 Click Copy Printer Settings.
Administrative support

Jam error messages appear on the printer control panel display and include the area of the printer where the jam occurred. When there is more than one jam, the number of jammed pages is displayed.
The following hints can help you avoid jams:

Clearing jams

When a jam occurs, a message indicating the jam location appears. Open doors and covers, and remove trays to access jam locations.
Jam number Access point To access the jam
200 250-sheet tray (Tray 1) and manual feeder
1 Open the front door, and then remove any jams. 2 Open the fuser cover, and then remove any jams. 3 Close the fuser cover. 4 Close the front door. 5 Pull out Tray 1, and then remove any jams. 6 Reinsert Tray 1.
201 Under the fuser
202 In the fuser
In the duplex area
24x 550-sheet tray 1 Pull the 550-sheet tray out, and then remove any jams. 2 Reinsert the tray.
250 In the multipurpose feeder 1 Press the release latch to the left to release the multipurpose feeder. 2 Inspect the multipurpose feeder, and then remove any jams. 3 Close the multipurpose feeder.
230–231and 235 · Clearing jams

1 If the jam is in the paper tray: a Grasp the handle, and pull the standard 250-sheet tray (Tray 1) and manual feeder out.

b Remove the jam.
d Press .
2 If the jam is inside the printer: a Grasp the front door at the side handholds, and then pull it toward you to open it.

Clearing jams

b If the jam is visible, remove the jammed paper.

The fuser cover closes when released.

Clearing jams


f Press .
1 Grasp the front door at the side handholds, and then pull it toward you to open it.
2 Remove the jam.
3 Load the tray with the correct paper size.
4 Insert the tray.
5 Close the front door.
6 Press .
Clearing jams

1 Grasp the handle, and pull the optional 550-sheet tray out.

2 Remove the jammed paper.
3 Insert the tray.
4 Press .
1 Push the lever in the multipurpose feeder down to access the jammed paper.

2 Remove the jam.
3 Insert the tray.
4 Press .
Clearing jams

Understanding printer messages
The printer is adjusting the color. Wait for the message to clear.
Close the upper and lower doors.
Insert the specified tray into the printer.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting

Try one or more of the following:
Try one or more of the following:
If there is no paper in the feeder, load a sheet, and then press to clear the message and continue printing. • Press to clear the message and continue printing.
The printer manually overrides the request, and then prints from an automatically selected tray. • Press , and then press to cancel the print job.
Try one or more of the following:
Try one or more of the following:
The printer manually overrides the request, and then prints from an automatically selected tray. • Press , and then press to cancel the print job.
Try one or more of the following:
If there is no paper in the feeder, load a sheet, and then select to clear the message and continue printing. • Press to clear the message and continue printing.
The printer manually overrides the request, and then prints from an automatically selected tray. • Press , and then press to cancel the print job.
Troubleshooting

Remove the stack of paper from the standard exit bin.
Check for and remove any packaging materials from the toner cartridges.
Remove the unrecognized USB device.
Remove the unrecognized USB hub.
Make sure that the camera is in a valid mode for PictBridge
Insert the missing toner cartridge to clear the message and continue printing. If the message appears again, remove the cartridge, and then insert it until it clicks into place.
Try one or more of the following:
Try one or more of the following:
Replace the black and color imaging kit.
Troubleshooting

Replace the unsupported toner cartridge with a supported one.
The paper in the selected tray is too short for the current print job.
Try one or more of the following:
The printer lacks sufficient memory to save settings. Install additional memory, or press to disable Resource Save, clear the message, and continue printing.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting

Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
The printer detects unformatted flash memory when the power is turned on.
Try one or more of the following:
The printer detects that a network port is installed, but cannot communicate with it. The printer disables all communication to the associated network interface.
Troubleshooting

Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Remove the additional tray(s).
4 Connect the power cord to a properly grounded outlet.
5 Turn the printer back on.
Only options designed specifically for this printer are supported.
Try one or more of the following:
Troubleshooting

Replace the waste toner bottle, and then press to clear the message.
Replace the waste toner bottle, and then press to clear the message.
Press to clear the message.
Press to clear the message.
The specified toner cartridge is exhausted.
1 Replace the specified toner cartridge.
2 Touch Continue to clear the message and continue printing.
If there are basic printer problems, or the printer is unresponsive, make sure:
Once you have checked each of these possibilities, turn the printer off, wait for about 10 seconds, and then turn the printer back on. This often fixes the problem.
The printer self test failed. Turn the printer off, wait about 10 seconds, and then turn the printer back on.
Troubleshooting

If Ready does not appear, turn the printer off and contact Customer Support.
Make sure the USB drive is supported.
These are possible solutions. Try one or more of the following:
Make sure Ready or Power Saver appears on the display before sending a job to print.
Remove the stack of paper from the standard exit bin.
Load paper in the tray.
Copies of the printer software are also available on the Lexmark Web site at http://support.lexmark.com.
MAKE SURE YOU ARE USING A RECOMMENDED USB, SERIAL, OR ETHERNET CABLE
For more information, visit the Lexmark Web site at http://support.lexmark.com.
Check the cable connections to the printer and print server to make sure they are secure.
For more information, see the setup documentation that came with the printer.
Troubleshooting

These are possible solutions. Try one or more of the following:
Eliminate the number and size of fonts, the number and complexity of images, and the number of pages in the job.
1 From the printer control panel, press .
2 Press the arrow buttons until Settings appears, and then press .
3 Press the arrow buttons until Setup Menu appears, and then press .
4 Press the arrow buttons until Print Recovery appears, and then press .
5 Press the arrow buttons until Page Protect appears, and then press .
6 Press the arrow buttons until Off appears, and then press .
C HECK THE PAPER TYPE SETTING
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the Paper Type setting.
MAKE SURE THE PRINTER IS NOT IN HEX TRACE MODE
If Ready Hex appears on the display, then you must exit Hex Trace mode before you can print your job. Turn the printer off and back on to exit Hex Trace mode.
These are possible solutions. Try one or more of the following:
Troubleshooting

USE THE SAME PAPER SIZE AND PAPER TYPE SETTINGS
These are possible solutions. Try one or more of the following:
From the Finishing menu or Print Properties, set Collate to On.
Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Add printer memory or an optional hard disk.
Increase the Print Timeout value:
1 From the printer control panel, press .
2 Press the arrow buttons until Settings appears, and then press .
3 Press the arrow buttons until General Settings appears, and then press .
4 Press the arrow buttons until Timeouts appears, and then press .
5 Press the arrow buttons until Print Timeout appears, and then press .
6 Press the arrow buttons until the desired value appears, and then press .
Troubleshooting

Settings chosen from the software program or application can change or override settings chosen from the printer control panel. If an option is not functioning, then make sure it is selected in the software as well as the printer control panel.
These are possible solutions. Try one or more of the following:
Turn the printer off, wait for about 10 seconds, and then turn the printer on.
1 Turn the printer off.
2 Unplug the printer from the wall outlet.
3 Check the connection between the option and the printer.
Print a menu settings page and check to see if the option is listed in the Installed Options list. If the option is not listed, reinstall it.
From the program you are using, select the option. Mac OS 9 users should make sure the printer is set up in the Chooser.
These are possible solutions. Try one or more of the following:
1 Open the paper tray.
2 Check for paper jams or misfeeds.
3 Make sure paper guides are aligned against the edges of the paper.
4 Make sure the paper tray closes properly.
Turn the printer off, wait about 10 seconds, and then turn the printer on.
Troubleshooting

If the paper tray is listed on the menu settings page, but paper jams when it enters or exits the tray, then it may not be properly installed. Reinstall the paper tray. For more information, see the hardware setup documentation that came with the paper tray, or go to http://support.lexmark.com to view the paper tray instruction sheet.
Make sure the memory card is securely connected to the printer system board.
Make sure the flash memory card is securely connected to the printer system board.
These are possible solutions. Try one or more of the following:
Make sure the 650-sheet duo drawer (multipurpose feeder) is installed properly.
Clear any jams in the multipurpose feeder.
Make sure:
Use recommended paper and specialty media. For more information, see “Paper and specialty media guidelines” on page 48.
Move the guides in the tray to the correct position for the size loaded.
If a service message appears, turn the printer off, wait about 10 seconds, and then turn the printer back on. If the error recurs, then call for service. You may have a printer part that requires adjustment or replacement.
Troubleshooting

These are possible solutions. Try one or more of the following:
Use recommended paper and specialty media. For more information, see “Paper and specialty media guidelines” on page 48.
MAKE SURE THERE IS NOT TOO MUCH PAPER IN THE PAPER TRAY
Make sure the stack of paper you load does not exceed the maximum stack height indicated in the tray or on the multipurpose feeder.
Move the guides in the tray to the correct positions for the paper size loaded.
1 Clear jammed paper from the entire paper path.
2 Press to clear the message and continue printing.
In the Setup menu, Jam Recovery is set to Off. Set Jam Recovery to Auto or On:
1 Press .
2 Press the arrow buttons until Settings appears, and then press .
3 Press the arrow buttons until General settings appears, and then press .
4 Press the arrow buttons until Print Recovery appears, and then press .
5 Press the arrow buttons until Jam Recovery appears, and then press .
6 Press the arrow buttons until On or Auto appears, and then press .
Troubleshooting

To help isolate print quality problems, print the print quality test pages:
1 Turn the printer off.
2 From the printer control panel, press and hold and the right arrow button while turning the printer on.
3 Release both buttons when the clock animation appears.
The printer performs its power-on sequence, and then Config Menu appears.
4 Press the arrow buttons until Prt Quality Pgs appears, and then press .
The pages are formatted, Printing Quality Test Pages appears, and then the pages print. The message remains on the display until all the pages print.
5 After the print quality test pages print, press the arrow buttons until Exit Config Menu appears, and then press .
The information in the following topics may help you solve print quality problems. If these suggestions still do not correct the problem, then call for service. You may have a printer part that requires adjustment or replacement.
These are possible solutions. Try one or more of the following:
Remove the toner cartridge and make sure the packing material is properly removed. Reinstall the toner cartridge.
When 88 Cartridge Low appears, order a new toner cartridge.
If the problem continues, the printer may need to be serviced. For more information, contact Customer Support.
Troubleshooting

Try one or more of the following:
Move the width and length guides in the tray to the correct positions for the paper size loaded.
Make sure the paper size setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the Paper Size setting.
These are possible solutions. Try one or more of the following:
If you are using downloaded fonts, then verify that the fonts are supported by the printer, the host computer, and the software program.
ABCDE
ABCDE ABCDE
Troubleshooting

The imaging kit may be defective.
If Black and color imaging kit life warning orBlack imaging kit life warning appears, replace the imaging kit.
ABCDE
ABCDE ABCDE
C HECK THE T ONER D ARKNESS SETTING
Select a lighter Toner Darkness setting:
These are possible solutions. Try one or more of the following:
Move the guides in the tray to the correct positions for the paper size loaded.
Make sure the paper size setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the Paper Size setting.
Troubleshooting

These are possible solutions. Try one or more of the following:
Replace the defective toner cartridge.
Replace the imaging kit.
These are possible solutions. Try one or more of the following:
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the Paper Type setting.
Troubleshooting

These are possible solutions. Try one or more of the following:
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the Paper Type setting.
Avoid textured paper with rough finishes.
When 88 <color> cartridge low appears or when the print becomes faded, replace the toner cartridge.
Replace the fuser.
These are possible solutions. Try one or more of the following:
The printer automatically calibrates the colors whenever a new imaging kit is detected. If a cartridge is replaced, then you can calibrate the colors manually:
1 From the printer control panel, press .
2 From the Admin menu, press the arrow buttons until Settings appears, and then press .
Troubleshooting

3 Press the arrow buttons until Quality menu appears, and then press .
4 Press the arrow buttons until Color Adjust appears, and then press .
Calibrating appears.
The Toner Darkness setting is too dark, the RGB Brightness setting is too dark, or the RGB Contrast setting is too high.
Avoid textured paper with rough finishes.
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the Paper Type setting.
Replace the imaging kit.
Troubleshooting

These are possible solutions. Try one or more of the following:
The printer automatically calibrates the colors whenever a new imaging kit is detected. If a cartridge is replaced, then you can calibrate the colors manually:
1 From the printer control panel, press .
2 From the Admin menu, press the arrow buttons until Settings appears, and then press .
3 Press the arrow buttons until Quality menu appears, and then press .
4 Press the arrow buttons until Color Adjust appears, and then press .
Calibrating appears.
The Toner Darkness setting is too light, the RGB Brightness setting is too light, or the RGB Contrast setting is too low.
Avoid textured paper with rough finishes.
Troubleshooting

Make sure the paper type setting matches the paper loaded in the tray.
1 From the printer control panel Paper menu, check the Paper Type setting.
Color Saver may be set to On.
When 88 <color> Cartridge Low appears or when the print becomes faded, replace the toner cartridge.
Replace the toner cartridge.
Replace the imaging kit.
REPEATING MARKS OCCUR REPEATEDLY ONLY IN ONE COLOR AND MULTIPLE TIMES ON A PAGE
Replace the developer unit if the defects occur every 43.9 mm (1.7 in.)
Replace the imaging kit if the defects occur every:

C HECK THE PAPER GUIDES
Move the guides in the tray to the correct positions for the paper size loaded.
Make sure you are using paper that meets the printer specifications.
The printer may need to be serviced. For more information, contact Customer Support.
These are possible solutions. Try one or more of the following:
Replace the imaging kit.
Contact Customer Support.
Troubleshooting

These are possible solutions. Try one or more of the following:
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Type setting from the Paper menu.
From the printer control panel Paper menu, make sure the Paper Texture setting matches the paper loaded in the tray.
These are possible solutions. Try one or more of the following:
Replace the imaging kit.
Contact Customer Support.
Troubleshooting

C HECK THE TRANSPARENCIES
Use only transparencies recommended by the printer manufacturer.
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Type setting from the Paper menu.
ABCDE ABCDE ABCDE
Replace the black and color imaging kit.
This section helps answer some basic color-related questions and describes how some of the features provided in the printer control panel Quality menu can be used to solve typical color problems.
ABCDE ABCDE ABCDE ABCDE
Color has shifted outside of the appropriate area or has been superimposed over another color area.
These are possible solutions. Try one or more of the following:
Troubleshooting

Remove the toner cartridges, and then reinstall them.
The printer will automatically calibrate the colors whenever a new imaging kit is detected. If a cartridge is replaced, then you can calibrate the colors manually:
1 From the printer control panel, press .
2 From the Admin menu, press the arrow buttons until Settings appears, and then press .
3 Press the arrow buttons until Quality menu appears, and then press .
4 Press the arrow buttons until Color Adjust appears, and then press .
Calibrating appears.
What is RGB color?
Red, green, and blue light can be added together in various amounts to produce a large range of colors observed in nature. For example, red and green can be combined to create yellow. Televisions and computer monitors create colors in this manner. RGB color is a method of describing colors by indicating the amount of red, green, or blue needed to produce a certain color.
What is CMYK color?
Cyan, magenta, yellow, and black inks or toners can be printed in various amounts to produce a large range of colors observed in nature. For example, cyan and yellow can be combined to create green. Printing presses, inkjet printers, and color laser printers create colors in this manner. CMYK color is a method of describing colors by indicating the amount of cyan, magenta, yellow, and black needed to reproduce a particular color.
How is color specified in a document to be printed?
Software programs typically specify document color using RGB or CMYK color combinations. Additionally, they allow users to modify the color of each object in a document. For more information, see the software program Help topics.
How does the printer know what color to print?
When a user prints a document, information describing the type and color of each object is sent to the printer. The color information is passed through color conversion tables that translate the color into the appropriate amounts of cyan, magenta, yellow, and black toner needed to produce the desired color. The object information determines the application of color conversion tables. For example, it is possible to apply one type of color conversion table to text while applying a different color conversion table to photographic images.
Should I use PostScript or PCL emulation printer software? What settings should I use for the best color?
The PostScript driver is strongly recommended for best color quality. The default settings in the PostScript driver provide the preferred color quality for the majority of printouts.
Troubleshooting

Why doesn't the printed color match the color I see on the computer screen?
The color conversion tables used in Auto Color Correction mode generally approximate the colors of a standard computer monitor. However, because of technology differences that exist between printers and monitors, there are many colors that can also be affected by monitor variations and lighting conditions. For recommendations on how the printer color sample pages may be useful in solving certain color-matching problems, see the question, “How can I match a particular color (such as a corporate logo)?”
The printed page appears tinted. Can I adjust the color?
Sometimes a printed page may appear tinted (for example, everything printed seems to be too red). This can be caused by environmental conditions, paper type, lighting conditions, or user preference. In these instances, adjust the Color Balance setting to create a more preferable color. Color Balance provides the user with the ability to make subtle adjustments to the amount of toner being used in each color plane. Selecting positive or negative values for cyan, magenta, yellow, and black (from the Color Balance menu) will slightly increase or decrease the amount of toner used for the chosen color. For example, if a printed page has a red tint, then decreasing both magenta and yellow could potentially improve the color balance.
My color transparencies seem dark when they are projected. Is there anything I can do to improve the color?
This problem most commonly occurs when projecting transparencies with reflective overhead projectors. To obtain the highest projected color quality, transmissive overhead projectors are recommended. If a reflective projector must be used, then adjusting the Toner Darkness setting to 1, 2, or 3 will lighten the transparency. Make sure to print on the recommended type of color transparencies.
What is manual color correction?
When manual color correction is enabled, the printer employs user-selected color conversion tables to process objects. However, Color Correction must be set to Manual, or no user-defined color conversion will be implemented. Manual color correction settings are specific to the type of object being printed (text, graphics, or images), and how the color of the object is specified in the software program (RGB or CMYK combinations).
To manually apply a different color conversion table:
1 From the Quality menu, select Color Correction, and then select Manual.
2 From the Quality menu, select Manual Color, and then select the appropriate color conversion table for the affected object type.
Troubleshooting

Object type Color conversion tables
How can I match a particular color (such as a corporate logo)?
From the printer Quality menu, nine types of Color Samples sets are available. These are also available from the Color Samples page of the Embedded Web Server. Selecting any sample set generates a multiple-page printout consisting of hundreds of colored boxes. Either a CMYK or RGB combination is located on each box, depending on the table selected. The observed color of each box is obtained by passing the CMYK or RGB combination labeled on the box through the selected color conversion table.
By examining Color Samples sets, a user can identify the box whose color is the closest to the desired color. The color combination labeled on the box can then be used for modifying the color of the object in a software program. For more information, see the software program Help topics. Manual color correction may be necessary to utilize the selected color conversion table for the particular object.
Selecting which Color Samples set to use for a particular color-matching problem depends on the Color Correction setting being used (Auto, Off, or Manual), the type of object being printed (text, graphics, or images), and how the color of the object is specified in the software program (RGB or CMYK combinations). When the printer Color Correction setting is set to Off, the color is based on the print job information; and no color conversion is implemented.
Note: The Color Samples pages are not useful if the software program does not specify colors with RGB or CMYK combinations. Additionally, certain situations exist in which the software program or the computer operating system adjusts the RGB or CMYK combinations specified in the program through color management. The resulting printed color may not be an exact match of the Color Samples pages.
What are detailed Color Samples and how do I access them?
Detailed Color Samples sets are available only through the Embedded Web Server of a network printer. A detailed Color Samples set contains a range of shades (displayed as colored boxes) that are similar to a user-defined RGB or CMYK value. The likeness of the colors in the set are dependent on the value entered in the RGB or CMYK Increment box.

To access a detailed Color Samples set from the Embedded Web Server:
1 Open a Web browser.
2 In the address bar, type the network printer IP address.
3 Click Configuration.
4 Click Color Samples.
5 Click Detailed Options to narrow the set to one color range.
6 When the Detailed Options page appears, select a color conversion table.
7 Enter the RGB or CMYK color number.
8 Enter an Increment value from 1–255.
9 Click Print to print the detailed Color Samples set.
When you call Customer Support, describe the problem you are experiencing, the message on the display, and the troubleshooting steps you have already taken to find a solution.
You need to know your printer model type and serial number. For more information, see the label on the inside top front cover of the printer. The serial number is also listed on the menu settings page.
In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, visit the Lexmark Web site at http://support.lexmark.com.
Troubleshooting

Product name:
Lexmark C540n, C543dn, C544n, C544dn, C544dw, C546dtn
Machine type:
Model(s):
210, 230, 410, 430, 43W, 439, n01, n02, dnw, xd1, xd2, dn1, dn2, gd1, gd2, dw1, dw2, dt1, dt2, gt1, gt2
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
If you don't have access to the Internet, you can contact Lexmark by mail:
Lexmark International, Inc. Bldg 004-2/CSC 740 New Circle Road NW Lexington, KY 40550 USA
© 2010 Lexmark International, Inc.
All rights reserved.
June 2011

This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.
Lexmark, Lexmark with diamond design, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
All other trademarks are the property of their respective owners.
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232–3000

Wireless-equipped models contain the following modular component(s):
Lexmark regulatory type/model LEX-M04-001; FCC ID:IYLLEXM04001; IC:2376A-M04001
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Values are subject to change. See www.lexmark.com for current values.
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products. If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching the metal frame of the printer.
Printing 48 dBA · Ready Inaudible

Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
Ambient temperature 15.6-32.2°C (60-90°F)
Shipping and storage temperature -40-43.3°C (-40-110°F)
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 7 milliwatt gallium arsenide laser operating in the wavelength of 655-675 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
A laser notice label may be affixed to this printer as shown:


The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard-copy output from electronic inputs. 480 W (C540, C543); 500 W (C544, C546)
Copying The product is generating hard-copy output from hard-copy original documents.
Scanning The product is scanning hard-copy documents. N/A
Ready The product is waiting for a print job. 34 W (C540, C543); 36 W (C544, C546)
Power Saver The product is in energy-saving mode.
Off The product is plugged into a wall outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.
This product is designed with an energy-saving mode called Power Saver. The Power Saver Mode is equivalent to the Sleep Mode. The Power Saver Mode saves energy by lowering power consumption during extended periods of inactivity. The Power Saver Mode is automatically engaged after this product is not used for a specified period of time, called the Power Saver Timeout.
Factory default Power Saver Timeout for this product (in minutes): 20 minutes (C540, C543); 30 minutes (C544, C546)
By using the configuration menus, the Power Saver Timeout can be modified between 1 minute and 240 minutes. Setting the Power Saver Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Power Saver Timeout to a high value maintains a fast response, but uses more energy.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the wall outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC and 2006/95/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
This section contains the following regulatory information pertaining to wireless products that contain transmitters, for example, but not limited to, wireless network cards or proximity card readers.
The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.
This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.

The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb
The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.
Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement.
Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada.
En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.
Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur et loin des fenêtres afin de garantir une protection optimale.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc-sc.gc.ca/rpb
Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme aux spécifications techniques d'Industry Canada.
Products bearing the CE mark are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment.
Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
Products equipped with 2.4GHz Wireless LAN option are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 1999/5/EC on the approximation and harmonization of the laws of the

Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment.
Compliance is indicated by the CE marking.
Operation is allowed in all EU and EFTA countries, but is restricted to indoor use only.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.
Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.
Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.
Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.
Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.

Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.
Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky
príslušné ustanovenia smernice 1999/5/ES.
Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Lexmark C540n, C543dn, C544n, C544dn, C544dw, C546dtn
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country- specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed.

To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web at http://support.lexmark.com.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.

Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.
PLEASE READ CAREFULLY BEFORE USING THIS PRODUCT: BY USING THIS PRODUCT, YOU AGREE TO BE BOUND BY ALL THE TERMS AND CONDITIONS OF THIS SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENT. IF YOU DO NOT AGREE WITH THE TERMS OF THIS SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENT, PROMPTLY RETURN THE PRODUCT UNUSED AND REQUEST A REFUND OF THE AMOUNT YOU PAID. IF YOU ARE INSTALLING THIS PRODUCT FOR USE BY OTHER PARTIES, YOU AGREE TO INFORM THE USERS THAT USE OF THE PRODUCT INDICATES ACCEPTANCE OF THESE TERMS.
This License Agreement (“Software License Agreement”) is a legal agreement between you (either an individual or a single entity) and Lexmark International, Inc. (“Lexmark”) that, to the extent your Lexmark product or Software Program is not otherwise subject to a written software license agreement between you and Lexmark or its suppliers, governs your use of any Software Program installed on or provided by Lexmark for use in connection with your Lexmark product. The term “Software Program” includes machine-readable instructions, audio/visual content (such as images and recordings), and associated media, printed materials and electronic documentation, whether incorporated into, distributed with or for use with your Lexmark product.
1 STATEMENT OF SOFTWARE LIMITED WARRANTY. Lexmark warrants that the media (e.g., diskette or compact disk) on which the Software Program (if any) is furnished is free from defects in materials and workmanship under normal use during the warranty period. The warranty period is ninety (90) days and commences on the date the Software Program is delivered to the original end-user. This limited warranty applies only to Software Program media purchased new from Lexmark or an Authorized Lexmark Reseller or Distributor. Lexmark will replace the Software Program should it be determined that the media does not conform to this limited warranty. 2 DISCLAIMER AND LIMITATION OF WARRANTIES. EXCEPT AS PROVIDED IN THIS SOFTWARE LICENSE AGREEMENT AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, LEXMARK AND ITS SUPPLIERS PROVIDE THE SOFTWARE PROGRAM "AS IS" AND HEREBY DISCLAIM ALL OTHER WARRANTIES AND CONDITIONS, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, TITLE, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ABSENCE OF VIRUSES, ALL WITH REGARD TO THE SOFTWARE PROGRAM. TO THE EXTENT LEXMARK CANNOT BY LAW DISCLAIM ANY COMPONENT OF THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, LEXMARK LIMITS THE DURATION OF SUCH WARRANTIES TO THE 90-DAY TERM OF THE EXPRESS SOFTWARE LIMITED WARRANTY.

This Agreement is to be read in conjunction with certain statutory provisions, as that may be in force from time to time, that imply warranties or conditions or impose obligations on Lexmark that cannot be excluded or modified. If any such provisions apply, then to the extent Lexmark is able, Lexmark hereby limits its liability for breach of those provisions to one of the following: providing you a replacement copy of the Software Program or reimbursement of the price paid for the Software Program.
The Software Program may include internet links to other software applications and/or internet web pages hosted and operated by third parties unaffiliated with Lexmark. You acknowledge and agree that Lexmark is not responsible in any way for the hosting, performance, operation, maintenance, or content of, such software applications and/or internet web pages. 3 LIMITATION OF REMEDY. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY AND ALL LIABILITY OF LEXMARK UNDER THIS SOFTWARE LICENSE AGREEMENT IS EXPRESSLY LIMITED TO THE GREATER OF THE PRICE PAID FOR THE SOFTWARE PROGRAM AND FIVE U.S. DOLLARS (OR THE EQUIVALENT IN LOCAL CURRENCY). YOUR SOLE REMEDY AGAINST LEXMARK IN ANY DISPUTE UNDER THIS SOFTWARE LICENSE AGREEMENT SHALL BE TO SEEK TO RECOVER ONE OF THESE AMOUNTS, UPON PAYMENT OF WHICH LEXMARK SHALL BE RELEASED AND DISCHARGED OF ALL FURTHER OBLIGATIONS AND LIABILITY TO YOU.
IN NO EVENT WILL LEXMARK, ITS SUPPLIERS, SUBSIDIARIES, OR RESELLERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, EXEMPLARY, PUNITIVE, OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LOST PROFITS OR REVENUES, LOST SAVINGS, INTERRUPTION OF USE OR ANY LOSS OF, INACCURACY IN, OR DAMAGE TO, DATA OR RECORDS, FOR CLAIMS OF THIRD PARTIES, OR DAMAGE TO REAL OR TANGIBLE PROPERTY, FOR LOSS OF PRIVACY ARISING OUT OR IN ANY WAY RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE PROGRAM, OR OTHERWISE IN CONNECTION WITH ANY PROVISION OF THIS SOFTWARE LICENSE AGREEMENT), REGARDLESS OF THE NATURE OF THE CLAIM, INCLUDING BUT NOT LIMITED TO BREACH OF WARRANTY OR CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY), AND EVEN IF LEXMARK, OR ITS SUPPLIERS, AFFILIATES, OR REMARKETERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY YOU BASED ON A THIRD-PARTY CLAIM, EXCEPT TO THE EXTENT THIS EXCLUSION OF DAMAGES IS DETERMINED LEGALLY INVALID. THE FOREGOING LIMITATIONS APPLY EVEN IF THE ABOVE-STATED REMEDIES FAIL OF THEIR ESSENTIAL PURPOSE. 4 U.S.A. STATE LAWS. This Software Limited Warranty gives you specific legal rights. You may also have other rights that vary from state to state. Some states do not allow limitations on how long an implied warranty lasts or the exclusion of limitation of incidental or consequential damages, so the above limitations may not apply to you. 5 LICENSE GRANT. Lexmark grants you the following rights provided you comply with all terms and conditions of this License Agreement:
a Use. You may Use one (1) copy of the Software Program. The term “Use” means storing, loading, installing,
executing, or displaying the Software Program. If Lexmark has licensed the Software Program to you for concurrent use, you must limit the number of authorized users to the number specified in your agreement with Lexmark. You may not separate the components of the Software Program for use on more than one computer. You agree that you will not Use the Software Program, in whole or in part, in any manner that has the effect of overriding, modifying, eliminating, obscuring, altering or de-emphasizing the visual appearance of any trademark, trade name, trade dress or intellectual property notice that appears on any computer display screens normally generated by, or as a result of, the Software Program. b Copying. You may make one (1) copy of the Software Program solely for purposes of backup, archiving, or
installation, provided the copy contains all of the original Software Program’s proprietary notices. You may not copy the Software Program to any public or distributed network. c Reservation of Rights. The Software Program, including all fonts, is copyrighted and owned by Lexmark International, Inc. and/or its suppliers. Lexmark reserves all rights not expressly granted to you in this License Agreement. d Freeware. Notwithstanding the terms and conditions of this License Agreement, all or any portion of the
Software Program that constitutes software provided under public license by third parties (“Freeware”) is licensed to you subject to the terms and conditions of the software license agreement accompanying such Freeware, whether in the form of a discrete agreement, shrink-wrap license, or electronic license terms at the

time of download. Use of the Freeware by you shall be governed entirely by the terms and conditions of such license. 6 TRANSFER. You may transfer the Software Program to another end-user. Any transfer must include all software components, media, printed materials, and this License Agreement and you may not retain copies of the Software Program or components thereof. The transfer may not be an indirect transfer, such as a consignment. Prior to the transfer, the end-user receiving the transferred Software Program must agree to all these License Agreement terms. Upon transfer of the Software Program, your license is automatically terminated. You may not rent, sublicense, or assign the Software Program except to the extent provided in this License Agreement, and any attempt to do so shall be void. 7 UPGRADES. To Use a Software Program identified as an upgrade, you must first be licensed to the original Software Program identified by Lexmark as eligible for the upgrade. After upgrading, you may no longer use the original Software Program that formed the basis for your upgrade eligibility. 8 LIMITATION ON REVERSE ENGINEERING. You may not alter, decrypt, reverse engineer, reverse assemble, reverse compile or otherwise translate the Software Program, except as and to the extent expressly permitted to do so by applicable law for the purposes of inter-operability, error correction, and security testing. If you have such statutory rights, you will notify Lexmark in writing of any intended reverse engineering, reverse assembly, or reverse compilation. You may not decrypt the Software Program unless necessary for the legitimate Use of the Software Program. 9 ADDITIONAL SOFTWARE. This License Agreement applies to updates or supplements to the original Software Program provided by Lexmark unless Lexmark provides other terms along with the update or supplement. 10 TERM. This License Agreement is effective unless terminated or rejected. You may reject or terminate this license at any time by destroying all copies of the Software Program, together with all modifications, documentation, and merged portions in any form, or as otherwise described herein. Lexmark may terminate your license upon notice if you fail to comply with any of the terms of this License Agreement. Upon such termination, you agree to destroy all copies of the Software Program together with all modifications, documentation, and merged portions in any form. 11 TAXES. You agree that you are responsible for payment of any taxes including, without limitation, any goods and services and personal property taxes, resulting from this Agreement or your Use of the Software Program. 12 LIMITATION ON ACTIONS. No action, regardless of form, arising out of this Agreement may be brought by either party more than two years after the cause of action has arisen, except as provided under applicable law. 13 APPLICABLE LAW. This Agreement is governed by the laws of the Commonwealth of Kentucky, United States of America. No choice of law rules in any jurisdiction shall apply. The UN Convention on Contracts for the International Sale of Goods shall not apply. 14 UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The Software Program has been developed entirely at private expense. Rights of the United States Government to use the Software Program is as set forth in this Agreement and as restricted in DFARS 252.227-7014 and in similar FAR provisions (or any equivalent agency regulation or contract clause). 15 CONSENT TO USE OF DATA. You agree that Lexmark, its affiliates, and agents may collect and use information you provide in relation to support services performed with respect to the Software Program and requested by you. Lexmark agrees not to use this information in a form that personally identifies you except to the extent necessary to provide such services. 16 EXPORT RESTRICTIONS. You may not (a) acquire, ship, transfer, or reexport, directly or indirectly, the Software Program or any direct product therefrom, in violation of any applicable export laws or (b) permit the Software Program to be used for any purpose prohibited by such export laws, including, without limitation, nuclear, chemical, or biological weapons proliferation. 17 AGREEMENT TO CONTRACT ELECTRONICALLY. You and Lexmark agree to form this License Agreement electronically. This means that when you click the “Agree” or “Yes” button on this page or use this product, you acknowledge your agreement to these License Agreement terms and conditions and that you are doing so with the intent to “sign” a contract with Lexmark.

18 CAPACITY AND AUTHORITY TO CONTRACT. You represent that you are of the legal age of majority in the place you sign this License Agreement and, if applicable, you are duly authorized by your employer or principal to enter into this contract. 19 ENTIRE AGREEMENT. This License Agreement (including any addendum or amendment to this License Agreement that is included with the Software Program) is the entire agreement between you and Lexmark relating to the Software Program. Except as otherwise provided for herein, these terms and conditions supersede all prior or contemporaneous oral or written communications, proposals, and representations with respect to the Software Program or any other subject matter covered by this License Agreement (except to the extent such extraneous terms do not conflict with the terms of this License Agreement, any other written agreement signed by you and Lexmark relating to your Use of the Software Program). To the extent any Lexmark policies or programs for support services conflict with the terms of this License Agreement, the terms of this License Agreement shall control.




Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.