
© 2008 Lexmark International, Inc. All rights reserved.

Edition notice January 2008 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time. © 2008 Lexmark International, Inc. All rights reserved.
UNITED STATES GOVERNMENT RIGHTS This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.


Follow these steps to set up your printer



1 Set up the printer hardware.
2 Decide how you want to connect the printer.
This guide includes three methods:

Setting up the printer


Unpack the printer, cables, and CD.

Grasp the paper tray handle, and then pull the tray completely out.
Raise the support bin.

Squeeze the width guide tabs together, and then slide the guide to the correct position for the size of paper being loaded.
Setting up the printer


Squeeze the length guide tabs together, and then slide the guide to the correct position for the size of paper being loaded.

Flex a stack of paper back and forth to loosen the sheets, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

Load the paper stack with the recommended print side faceup. Load the stack toward the back of the tray as shown.

Align the tray, and then reinsert it.
Setting up the printer


Grasp the handle, and pull forward to open the front door.

Allow the front door to open completely.

Pull the protective sheet straight out of the toner cartridge area to remove it.

Pull each toner cartridge straight out of the printer, one at a time.
Setting up the printer


Firmly shake the toner cartridge side-to-side and front- to-back several times to distribute the toner.

Remove the red packing material from each toner cartridge.

Place each toner cartridge back into the printer.

Pull out on each side of the packing strip, and then pull it forward to remove it from the transfer module.

Remove the red packing strip from the top of each photoconductor.
Setting up the printer


Close the front door.
Setting up the printer

For detailed steps, see “Information you will need to set up the printer on a wireless network” on page 12 and “Installing the printer on a wireless network (Windows)” on page 14.
For detailed steps, see “Information you will need to set up the printer on a wireless network” on page 12 and “Installing the printer on a wireless network (Macintosh)” on page 16.
For detailed steps, see “Connecting using a USB cable” on page 32.
For detailed steps, see “Connecting using an Ethernet network” on page 33.
Choosing a connection method

Information you will need to set up the printer on a wireless network
Some ad hoc networks will also require the auto setting. Check with your system support person if you are not sure which channel to select. • Security Method—There are three basic options for Security Method: – WEP key
If your network uses more than one WEP key, enter up to four in the provided spaces. Select the key currently in use on the network by selecting the Default WEP Transmit Key. or – WPA or WPA2 passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network. – No security
If your wireless network does not use any type of security, then you will not have any security information.
If you are installing the printer on an 802.1X network using the Advanced method, then you may need the following:
Every network device has a unique hardware identification number to distinguish it from other network devices. This identification number is called the Media Access Control (MAC) address.
A list of MAC addresses can be set on a wireless router so that only those devices with matching MAC addresses can join the network. This is called MAC address filtering. When installing the printer on a network that uses MAC address filtering, be sure to add the printer MAC address to the list of addresses allowed by the wireless router. If this address is not specifically allowed on the wireless network, the printer will not work wirelessly.
Preparing to connect wirelessly

If the printer has a factory-installed internal print server, the MAC address is a series of letters and numbers located on the MAC address sheet that shipped with the printer.
The MAC address appears in the following format:
00:04:12:34:56:78
Preparing to connect wirelessly


Before you install the printer on a wireless network, make sure that:
1 Connect the power cable to the printer and then to a properly grounded electrical outlet, and then turn the printer on.



Make sure the printer and computer are fully on and ready.

Do not connect the USB cable until instructed to do so on the screen.
2 Insert the Software and Documentation CD.

Connecting to a wireless network using Windows

3 Click Install.
4 Click Agree.
5 Click Suggested.
6 Click Wireless Network Attach.
7 Temporarily connect a USB cable between the computer on the wireless network and the printer.

8 Follow the on-screen instructions to complete the software installation.
9 To allow other computers on the wireless network to use the wireless printer, follow steps 2 through 6 and step 8 for each computer.
Connecting to a wireless network using Windows


1 Locate the printer MAC address on the sheet that shipped with the printer. Write the last six digits of the MAC address in the space provided below:
2 Connect the power cable to the printer and then to a properly grounded electrical outlet, and then turn the power on.
1 Access the AirPort options.
a From the Finder desktop, click Apple menu System Preferences. b Click Network.
c Click AirPort.
a From the Finder desktop, click Go Applications. b From the Applications folder, double-click Internet Connect.
c From the toolbar, click AirPort.
Connecting to a wireless network using Macintosh

2 From the Network popup menu, select print server xxxxxx, where the x’s are the last six digits of the MAC address located on the MAC address sheet.
3 Open the Safari browser.
4 From the Bookmarks drop-down menu, select Show.
5 Under Collections, select Bonjour or Rendevous, and then double-click the printer name.
6 From the main page of the Embedded Web Server, navigate to the page where the wireless settings information is stored.
1 Type the name of your network (SSID) in the appropriate field.
2 Select Infrastructure as your Network Mode if you are using a wireless router.
3 Select the type of security you use to protect your wireless network.
4 Enter the security information necessary for the printer to join your wireless network.
5 Click Submit.
6 Open the AirPort application on your computer:
a From the Finder desktop, click Apple menu System Preferences. b Click Network.
c Click AirPort.
a From the Finder desktop, click Go Applications. b From the Applications folder, double-click Internet Connect.
c From the toolbar, click AirPort.
7 From the Network popup menu, select your wireless network.
To print to a network printer, each Macintosh user must install a custom PostScript Printer Description (PPD) file and create a printer in the Print Center or Printer Setup Utility.
1 Install a PPD file on the computer: a Insert the Software and Documentation CD in the CD or DVD drive. b Double-click the installer package for the printer.
c From the Welcome screen, click Continue. d Click Continue again after viewing the Readme file. e Click Continue after viewing the license agreement, and then click Agree to accept the terms of the
agreement. f Select a Destination, and then click Continue. g From the Easy Install screen, click Install.
Connecting to a wireless network using Macintosh

h Type the user password, and then click OK.
All necessary software is installed on the computer. i Click Close when installation is complete.
1 From the Finder desktop, click Apple menu System Preferences. 2 Click Print & Fax. 3 Click +. 4 Select the printer from the list. 5 Click Add.
1 From the Finder desktop, click Go Applications. 2 Double-click the Utilities folder. 3 Locate and double-click Printer Setup Utility or Print Center. 4 From the Printer List, choose Add. 5 Select the printer from the list. 6 Click Add. b For AppleTalk printing:
1 From the Finder desktop, click Apple menu System Preferences. 2 Click Print & Fax. 3 Click +. 4 Click AppleTalk. 5 Select the printer from the list. 6 Click Add.
1 From the Finder desktop, click Go Applications. 2 Double-click the Utilities folder. 3 Locate and double-click Print Center or Printer Setup Utility. 4 From the Printer List, choose Add. 5 Choose the Default Browser tab. 6 Click More Printers. 7 From the first pop-up menu, choose AppleTalk. 8 From the second pop-up menu, select Local AppleTalk zone. 9 Select the printer from the list. 10 Click Add.
Connecting to a wireless network using Macintosh

In serial printing, data is transferred one bit at a time. Although serial printing is usually slower than parallel printing, it is the preferred option when there is a great deal of distance between the printer and computer or when an interface with a better transfer rate is not available.
After installing the serial port, you will need to configure the printer and the computer so they can communicate. Make sure you have connected the serial cable to the serial port on your printer.
1 Set the parameters in the printer: a From the printer control panel, navigate to the menu with port settings. b Locate the submenu with serial port settings.
c Make any necessary changes to the serial settings. d Save the new settings. e Print a menu settings page.
2 Install the printer driver: a Insert the Software and Documentation CD. It launches automatically.
If the CD does not launch automatically, do one of the following:
. 2 In the Start Search box, type D:\setup.exe, where D is the letter of your CD or DVD drive.
1 Click Start. 2 Click Run. 3 Type D:\setup.exe, where D is the letter of your CD or DVD drive.
b Click Install Printer and Software.
c Click Agree to accept the Printer Software License Agreement. d Click Custom. e Make sure Select Components is selected, and then click Next.
f Make sure Local is selected, and then click Next. g Select the manufacturer of the printer from the menu. h Select the printer model from the menu, and then click Add Printer.
i Click the + beside the printer model under Select Components. j Make sure the correct port is available under Select Components. This is the port where the serial cable attaches to the computer. If the correct port is not available, select the port under the Select Port menu, and then click Add Port. k Make any configuration changes necessary in the Add a New Port window. Click Add Port to finish adding
the port. l Make sure the box next to the selected printer model is checked. m Select any other optional software you want to install, and then click Next.
n Click Finish to complete the printer software installation.
Connecting to a wireless network using Macintosh
1 Click

3 Set the COM port parameters:
After the printer driver is installed, you must set the serial parameters in the communications (COM) port assigned to the printer driver.
The serial parameters in the COM port must match the serial parameters you set in the printer.
a Open the Device Manager. Do one of the following:
. 2 Click Control Panel. 3 Click System and Maintenance. 4 Click System. 5 Click Device Manager.
1 Click Start. 2 Click Control Panel. 3 Click Performance and Maintenance. 4 Click System. 5 From the Hardware tab, click Device Manager.
1 Click Start. 2 Click Settings Control Panel. 3 Click System. 4 From the Hardware tab, click Device Manager. b Click + to expand the list of available ports.
c Select the communications port where you attached the serial cable to your computer (example: COM1). d Click Properties. e On the Port Settings tab, set the serial parameters to the same serial parameters in the printer.
Look for the printer settings under the serial heading on the Menu Settings page you printed earlier. f Click OK, and then close all the windows. g Print a test page to verify printer installation. When a test page prints successfully, printer setup is complete.
Connecting to a wireless network using Macintosh
1 Click

For more information on networking terms and concepts, refer to the User's Guide on the Software and Documentation CD.
Before beginning to troubleshoot the wireless printer, verify that:
Print a network setup page to verify the SSID the printer is using.
If you are not sure if the SSID is correct, run the wireless setup again.
If you are not sure if your security information is correct, run the wireless setup again.
Try accessing other computers on the wireless network.
If the network has Internet access, try connecting to the Internet over a wireless connection.
For most networks, the printer should be within 100 feet (30 meters) of the wireless access point (wireless router).
Remove any large metal objects between the access point and the printer.
Make sure the printer and wireless access point are not separated by poles, walls, or support columns containing metal or concrete.
Many devices can interfere with the wireless signal, including baby monitors, motors, cordless phones, security system cameras, other wireless networks, and some Bluetooth devices.
A network setup page lists the configuration settings of the printer, including the IP address and MAC address. This information is very helpful when troubleshooting the network configuration of the printer.
For more information on printing a network setup page, refer to the User's Guide on the installation software CD.

If you encountered problems while installing, or if your printer does not appear in the printers folder or as a printer option when sending a print job, you can try uninstalling and reinstalling the software.
These are possible solutions. Try one or more of the following:
MAKE SURE YOUR COMPUTER IS CONNECTED TO YOUR WIRELESS ACCESS POINT (WIRELESS ROUTER)
MOVE THE COMPUTER AND/OR PRINTER CLOSER TO THE WIRELESS ROUTER
Although the possible distance between devices in 802.11b or 802.11g networks is 300 feet, the maximum range for optimal performance is generally 100–150 feet.
There may be temporary interference from other devices such as microwave ovens or other appliances, cordless phones, baby monitors, and security system cameras. Make sure your access point is not positioned too closely to these devices.
CHECK WHETHER THE PRINTER IS ON THE SAME WIRELESS NETWORK AS THE
Print a network setup page. Refer to the documentation that came with your printer for details on printing a network setup page.
Make sure the SSID the printer is using matches the wireless network SSID. If you are not sure how to find the network SSID, use one of the following:
1 Type the IP address of the wireless access point in the address field of your Web browser.
If you do not know the IP address of the wireless access point:
a Do one of the following:
. 2 Click All Programs Accessories. 3 Click Command Prompt.
1 Click Start. 2 Click All Programs or Programs Accessories Command Prompt.
1 Click

b Type ipconfig.
c Press Enter.
2 Type your user name and password for the wireless access point when prompted.
3 Click OK.
4 On the main page, click Wireless or another selection where settings are stored. The SSID appears.
5 Write down the SSID, security type, and the WEP key/WPA passphrase (if shown).
6 Store the SSID and the WEP key or WPA passphrase in a safe place for future reference.
In Mac OS X version 10.5
1 From the menu bar, click Apple menu System Preferences.
2 Click Network.
3 Click AirPort.
The SSID of the network the computer is connected to is displayed in the Network Name pop-up menu.
4 Write down the SSID.
1 From the menu bar, click Go Applications.
2 From the Applications folder, double-click Internet Connect.
3 From the toolbar, click AirPort.
The SSID of the network the computer is connected to is displayed in the Network pop-up menu.
4 Write down the SSID.
1 Type the IP address of the wireless access point in the address field of your Web browser and continue to Step 2.
If you do not know the IP address of the wireless access point, then do the following:
a From the menu bar, click Apple menu System Preferences. b Click Network.
c Click AirPort.

d Click Advanced. e Click TCP/IP.
The “Router” entry is typically the wireless access point.
a From the menu bar, click Apple menu System Preferences. b Click Network.
c From the Show pop-up menu, select Airport. d Click TCP/IP.
The “Router” entry is typically the wireless access point.
2 Type your user name and password when prompted.
3 Click OK.
4 On the main page, click Wireless or another selection where settings are stored. The SSID will be displayed.
5 Write down the SSID, security type and the WEP key/WPA passphrase (if shown).
If your wireless access point is using Wireless Equivalent Privacy (WEP) security, the WEP key should be:
or • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard. ASCII characters in a WEP key are case-sensitive.
If your wireless access point is using Wi-Fi Protected Access (WPA) security the WPA passphrase should be:
or • Exactly 64 hexadecimal characters. Hexadecimal characters are A-F, a-f, and 0-9.
When you are connected to another network through a VPN connection, you will not be able to access the printer over your wireless network. End your VPN session and try printing again.

You will lose your connection to a wireless printer on your local network when connected to most Virtual Private Networks (VPNs). Most VPNs allow users to communicate with only the VPN and no other network at the same time. If you would like to have the ability to connect to your local network and to a VPN at the same time, the system support person for the VPN must enable split tunneling. Be aware that some organizations will not allow split tunneling due to security or technical concerns.
If the configuration software does not let you continue configuring your printer wirelessly after you attach the USB cable, then there may be a problem with the cable. Try one or more of the following:

1 Attach the large, rectangular connector to any USB port on your computer. USB ports may be on the front or the back of the computer, and may be horizontal or vertical.

2 Attach the small, square connector to the printer.

E RROR MADE WHEN ENTERING KEY
A valid WEP key must be:
or • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard.
A valid WPA pre-shared key must be:
or • Exactly 64 hexadecimal characters. Hexadecimal characters are A-F, a-f, and 0-9.
There are several reasons why the target network might not appear in the list of networks during printer setup.
Some networks will not appear in the network list because they do not broadcast their SSIDs.
1 Select I want to enter a different network.
2 Click Next.
3 Enter the SSID, wireless mode, and channel (if ad hoc is selected) information.
4 Click Next and continue the installation.

1 Select I want to enter a different network. 2 Click Next, and then complete the required network information.
THE PRINTER OR INSTALLING COMPUTER IS TOO FAR AWAY FROM THE ACCESS POINT
Confirm that the network equipment is functioning properly:
THERE IS RF (RADIO FREQUENCY) INTERFERENCE BETWEEN THE WIRELESS
Limit the sources of RF interference between the wireless access point and the installing computer by rearranging the network and items in the signal path. Sources of RF interference include:

THERE IS AN OBJECT BLOCKING THE SIGNAL BETWEEN THE PRINTER AND THE
The wireless signal can also be distorted or blocked by objects in the path between the access point and the printer.
A wireless device will communicate on the network only when no other device is communicating. Too many computers, printers, and other wireless devices can cause a wireless network to be so busy that a new device is unable to send or receive information.
These are possible solutions. Try one or more of the following:

If the Wireless Setup Utility stops responding during the wireless configuration process, restart the computer. Insert the Software and Documentation CD and run the Wireless Setup Utility again.
These are possible solutions. Try one or more of the following:

All computers that print to the wireless printer must first have the printer driver installed.
Third-party (non-Microsoft) firewalls can interfere with wireless printing. If the printer and computer are configured correctly, and the wireless network is working, but the printer will not print wirelessly, a firewall could be the problem. If there is a firewall (other than the Windows firewall) on the computer, try one or more of the following:
Network printer does not show up in the printer selection list during installation
MAKE SURE THE PRINTER IS ON THE SAME WIRELESS NETWORK AS THE COMPUTER
The SSID of the printer must match the SSID of the wireless network.
1 Type the IP address of your wireless access point into the address field of your browser. a If you do not know the IP address of the wireless access point, do one of the following:
. 2 Click All Programs Accessories. 3 Click Command Prompt.
1 Click Start. 2 Click All Programs or Programs Accessories Command Prompt. b Type ipconfig.
1 Click

c Press Enter.
2 Type the user name and password for the access point when prompted.
3 Click OK.
4 Locate the page where the SSID is displayed.
5 Write down the SSID, security type, and the WEP key or WPA passphrase, if they are shown.
1 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start.
2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Click Wireless Setup Utility.
4 Follow the instructions on the computer screen, including typing in the SSID of the wireless access point and the WEP key or WPA passphrase when prompted.
5 Store the SSID and the WEP key or WPA passphrase in a safe place for future reference.

USB setup and connection
1 Insert the Software and Documentation CD.
2 Click Install.
3 Click Agree.
4 Click Suggested.
5 Click Local Attach.
6 Connect the installation cable to a USB port on the computer and the USB port on the back of the printer.

7 Connect the power cable to the printer and then to a properly grounded electrical outlet, and then turn the printer on.

8 Follow the on-screen instructions to complete the USB configuration.
Connecting using a USB cable

Wired setup and connection
1 Connect the Ethernet cable to the printer and to an active Ethernet port on the network.

Make sure the computer you are using to configure the printer is attached to a working network port on the same network as the printer.
2 Connect the power cable to the printer and then to a properly grounded electrical outlet, and then turn the printer on.

3 Insert the Software and Documentation CD.
4 Click Install.
5 Click Agree.
6 Click Suggested.
7 Click Wired Network Attach.
8 Follow the on-screen instructions to complete the wired configuration.
Connecting using an Ethernet network

ad hoc mode A setting for a wireless device that lets it communicate directly with other wireless devices without an access point or router.
ad hoc network A wireless network that does not use an access point.
AutoIP address An IP address automatically assigned by a network device. If the device is set to use DHCP, but no DHCP server is available, an AutoIP address may be assigned by the device.
BSS (Basic Service Set) Basic Service Set describes the type of wireless network that you are using. The BSS type can be one of the following: Infrastructure network or Ad-Hoc network.
channel A specific radio frequency used by two or more wireless devices to communicate with each other. All devices on the network must use the same channel.
DHCP (Dynamic Host Configuration Protocol)
A language used by DHCP servers.
DHCP IP address An IP address automatically assigned by a DHCP server.
DHCP server A computer or router that gives a unique IP address to each device on the network. Unique addresses prevent conflicts.
infrastructure mode A setting for a wireless device that lets it communicate directly with other wireless devices using an access point or router.
installation cable Connects the printer to the computer temporarily during some methods of installation.
internal wireless print server A device that lets computers and printers talk to each other over a network without cables.
IP (Internet Protocol) address The network address of a computer or printer. Each device on the network has its own network address. The address may be assigned manually by you (Static IP address), automatically by the DHCP server (DHCP IP address), or automatically by the device (AutoIP address).
ipconfig A command that displays the IP address and other network information of a Windows computer.
MAC (Media Access Control) address A hardware address that uniquely identifies each device on a network.
MAC filtering A method of limiting access to your wireless network by specifying which MAC addresses may communicate on the network. This setting may be specified on wireless routers or access points.
network adapter/card A device that lets computers or printers talk to each other over a network.
network hub A device that connects multiple devices on a wired network.
network name See “SSID (Service Set Identifier)” on page 35
ping A test to see if your computer can communicate with another device.
printer nickname The name you assign to your printer so that you and others can identify it on the network.
router A device that shares a single Internet connection with multiple computers or other devices. The basic router controls network traffic.
Networking glossary

security key A password, such as a WEP key or a WPA pass phrase, used to make a network secure.
signal strength Measure of how strongly a transmitted signal is being received.
SSID (Service Set Identifier) The name of a wireless network. When you connect a printer to a wireless network, the printer needs to use the same SSID as the network. Also referred to as network name or BSS (Basic Service Set).
Static IP address An IP address assigned manually by you.
switch A device similar to a network hub that can connect different networks together
UAA (Universally Administered Address)
An address assigned to a network printer or print server by the manufacturer. To find the UAA, print a network setup page and look for the UAA listing.
USB cable A lightweight, flexible cable that lets the printer communicate with the computer at much higher speeds than parallel cables
USB port A small, rectangular port on the back of the computer that connects the peripheral devices using a USB cable, and lets them communicate at high speeds
WEP (Wired Equivalent Privacy) A security setting that helps prevent unauthorized access to a wireless network. Other possible security settings are WPA and WPA2.
wireless access point A device that connects wireless devices together to form a wireless network
wireless router A router that also serves as a wireless access point
Wi-Fi An industry term that describes the technology used to create an interoperable wireless local area network (WLAN).
WPA (Wi-Fi Protected Access) A security setting that helps prevent unauthorized access to a wireless network. WPA is not supported on ad hoc wireless networks. Other possible security settings are WEP and WPA2.
WPA2 A newer version of WPA. Older routers are less likely to support this. Other possible security settings are WPA and WEP.
Networking glossary
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.