EN
Lexmark logo
Official user manual

Lexmark 925dte

105 pages·2.7 MB·Printer·PDF·ENDEFRITNLJA
Lexmark 925dte
Table of Contents 47 sections Contents · Introduction · Understanding letters after model numbers · Learning about the printer · … ShowHide
Page 1 of the Lexmark 925dte user manual — May 2012 www.lexmark.com
Page 1 · click to enlarge
Page 1

C925de, C925dte, X925de

Technical Reference

May 2012 www.lexmark.com

Page 2 of the Lexmark 925dte user manual — Edition notice
Page 2 · click to enlarge
Page 2

Edition notice

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.

References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.

For Lexmark technical support, visit http://support.lexmark.com. For information on supplies and downloads, visit www.lexmark.com. If you don't have access to the Internet, you can contact Lexmark by mail: Lexmark International, Inc. Bldg 004-2/CSC 740 New Circle Road NW Lexington, KY 40550 USA

© 2012 Lexmark International, Inc. All rights reserved.

Trademarks Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries. PCL® is a registered trademark of the Hewlett-Packard Company. All other trademarks are the property of their respective owners.

GOVERNMENT END USERS The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commerical Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.

May 2012

Page 5 of the Lexmark 925dte user manual — Understanding letters after model numbers
Page 5 · click to enlarge
Page 5

Introduction

Overview

This edition of the Technical Reference contains information about the following printers or multifunction printers (MFPs):

Understanding letters after model numbers

Some LexmarkTM printers and MFP options may have one or more letters after the model number to indicate features.

AcronymMeaning dduplex1 deduplex and e-Task (electronic task) touch-screen interface dfeduplex, finisher/stapler, and e-Task touch-screen interface dheduplex, high-capacity drawer, and e-Task touch-screen interface dhnduplex, high-capacity drawer, and network dmeduplex, mailbox, and e-Task touch-screen interface dnduplex and network dnfduplex, network, and finisher/stapler dnw or dwduplex, network, and wireless dtduplex and additional tray2 dteduplex, additional tray2, and e-Task touch-screen interface dtfeduplex, additional tray2, finisher/stapler, and e-Task touch-screen interface dtmeduplex, additional tray2, mailbox, and e-Task touch-screen interface dtnduplex, additional tray2, and network dtpeduplex, additional tray2, finisher with hole punch, and e-Task touch-screen interface dttnduplex, tandem tray module, and network dtseduplex, additional tray2, stacker, and e-Task touch-screen interface dtweduplex, additional tray2, wireless, and e-Task touch-screen interface ee-Task touch-screen interface hdnhard disk, duplex, and network 1 Duplex (two‑sided) printing using an optional duplex unit or an internal duplex unit based on the product 2 The additional tray may be part of a drawer.
Lexmark 925dte — Understanding letters after model numbers diagram (page 5)
Fig. 1 · Understanding letters after model numbers

Introduction 5 · C925de C925dte X925de

Page 6 of the Lexmark 925dte user manual — Introduction
Page 6 · click to enlarge
Page 6
AcronymMeaning nnetwork nlnetwork light model ninetwork and ImageQuick tnnetwork and additional tray2 1 Duplex (two‑sided) printing using an optional duplex unit or an internal duplex unit based on the product 2 The additional tray may be part of a drawer.

Introduction 6

Page 7 of the Lexmark 925dte user manual — Learning about the printer
Page 7 · click to enlarge
Page 7

Learning about the printer 7

Learning about the printer

Finding information about the printer

What are you looking for?Find it here Initial setup instructions: • Connecting the printer • Installing the printer softwareSetup documentation—The setup documentation came with the printer and is also available on the Lexmark Web site at http://support.lexmark.com. Additional setup and instructions for using the printer: • Selecting and storing paper and specialty media • Loading paper • Configuring printer settings • Viewing and printing documents and photos • Setting up and using the printer software • Configuring the printer on a network (depending on your printer model) • Caring for and maintaining the printer • Troubleshooting and solving problemsUser's Guide—The User's Guide is available on the Software and Documentation CD. For updates, check our Web site at http://support.lexmark.com. Instructions for: • Installing the printer using Guided or Advanced wireless setup • Connecting the printer to an Ethernet or a wireless network • Troubleshooting printer connection problemsNetworking Guide—Open the Software and Documentation CD, and then look for Printer and Software Documentation under the Pubs folder. From the list of publications, click the Networking Guide link. Help using the printer softwareWindows or Mac Help—Open a printer software program or application, and then click Help. ? Click to view context‑sensitive information. Notes: • Help is automatically installed with the printer software. • The printer software is located in the printer program folder or on the desktop, depending on your operating system.
Page 8 of the Lexmark 925dte user manual — Learning about the printer
Page 8 · click to enlarge
Page 8

Learning about the printer 8

What are you looking for?Find it here Latest supplemental information, updates, and customer support: • Documentation • Driver downloads • Live chat support • E‑mail support • Voice supportLexmark Support Web site— http://support.lexmark.com Note: Select your country or region, and then select your product to view the appropriate support site. Support telephone numbers and hours of operation for your country or region can be found on the Support Web site or on the printed warranty that came with your printer. Record the following information (located on the store receipt and at the back of the printer), and have it ready when you contact customer support so that they may serve you faster: • Machine Type number • Serial number • Date purchased • Store where purchased Warranty informationWarranty information varies by country or region: • In the US—See the Statement of Limited Warranty included with this printer, or at http://support.lexmark.com. • In other countries and regions—See the printed warranty that came with your printer.
Page 9 of the Lexmark 925dte user manual — Printable areas
Page 9 · click to enlarge
Page 9

Printer Control Language (PCL) page formatting 9

Printer Control Language (PCL) page formatting

For more information on PCL, see the Printer Languages and Interfaces Technical Reference. It contains a complete listing with descriptions of PCL commands.

To determine which PCL commands your printer supports, see “Appendix A: PCL support” on page 22.

Printable areas

The printable areas and logical pages for PCL emulation (both portrait and landscape orientation) are illustrated below. See the legend that follows for definitions of areas A through I.

Lexmark 925dte — Printable areas diagram (page 9)
Fig. 2 · Printable areas
Legend: APortrait physical page width and landscape physical page length BPortrait physical page length and landscape physical page width CPortrait logical page width DLandscape logical page width EDistance between the side edge of the physical page and the logical page in portrait FDistance between the side edge of the physical page and the logical page in landscape GDistance between the top and bottom edge of the physical page and logical page HDistance between the left and right edge of the physical page and the printable area in portrait, or distance between the top and bottom edge of the physical page and printable area in landscape IDistance between the top and bottom edge of the physical page and the printable area in portrait, or distance between the left and right edge of the physical page and the printable area in landscape
Page 10 of the Lexmark 925dte user manual — Supported paper and envelope dimensions
Page 10 · click to enlarge
Page 10

Printer Control Language (PCL) page formatting 10

Supported paper and envelope dimensions

The following table lists the page sizes and print area dimensions for all supported paper and envelope sizes. For more information about the printable areas and logical pages for PCL emulation, see “Printable areas” on page 9.

SelectionPaper/envelope dimensionsDimensions by area (pels)1 Page size parameters2NamemminchesABCDEFGHI Paper 2, 602Letter216 x 2798.5 x 1151006600480063601501200100100 3, 603Legal216 x 3568.5 x 1451008400480081601501200100100 12, 45, 612JIS B5182 x 2577.2 x 10.143006070400058301501200100100 26, 626A4 (198 mm)3210 x 2978.3 x 11.74960701446766778142118080100 26, 626A4 (203 mm)3210 x 2978.3 x 11.7496070144800677880118080100 1, 601Executive184.2 x 266.77.25 x 10.543506300405060601501200100100 13, 613A5148 x 2105.83 x 8.2734964960319647201421180100100 300Oficio (México)215.9 x 340.48.5 x 13.451008040480078001501200100100 46JIS B4257 x 36410.12 x 14.3360708600578683641421180100100 27A3297 x 42011.7 x 16.5470149920673096841421180100100 6 or 1111 x 17279.4 x 431.811 x 17660010200630099601501200100100 4 or 10Folio216 x 3308.5 x 1351007800480075601501200100100 15Statement139.7 x 215.95.5 x 8.533005100300048601501200100100 24A6105 x 1484.13 x 5.8324803496219932601421180100100 1 Pel dimensions are for 600 dpi. 2 Page Size Parameters are explained in the Page Control table in the PCL chapter of the Printer Language and Interfaces Technical Reference. 3 The width of the logical page for A4 paper can be changed from the printer control panel or your application. 4 For the Universal paper size, the area dimensions are listed in pel ranges. 5 Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039. 6 To support two‑sided printing, the Universal paper size length must be between 5.83 inches (148 mm) and 17 inches (431.8 mm); and the width must be between 8.27 inches (210 mm) and 11.69 inches (297 mm). Note: The explanation of the printable area assumes that the Print Area menu item is set to Normal. For more information, see “Print Area Menu Item” in the PCL chapter of the Printer Language and Interfaces Technical Reference.
Page 11 of the Lexmark 925dte user manual — Supported paper and envelope dimensions
Page 11 · click to enlarge
Page 11

Printer Control Language (PCL) page formatting 11

SelectionPaper/envelope dimensionsDimensions by area (pels)1 Page size parameters2NamemminchesABCDEFGHI 101Universal297 x 1219611.69 x 4862124– 701443498– 2880041824– 671443258– 2856041501200100100 Envelope 807 3/4 Envelope98.4 x 190.53.875 x 7.523244500202442601501200100100 899 Envelope98.4 x 225.43.875 x 8.87523245324202450841501200100100 8110 Envelope104.8 x 241.34.125 x 9.524745700217454601501200100100 90DL Envelope220 x 1108.66 x 4.3325985196231449601421180100100 91C5 Envelope229 x 1629.02 x 6.3838265408354251721421180100100 995, 100B5 envelope176.0 x 250.06.93 x 9.8441565904387256681421180100100 600Other Envelope216 x 3568.5 x 1470128400480081601501200100100 1 Pel dimensions are for 600 dpi. 2 Page Size Parameters are explained in the Page Control table in the PCL chapter of the Printer Language and Interfaces Technical Reference. 3 The width of the logical page for A4 paper can be changed from the printer control panel or your application. 4 For the Universal paper size, the area dimensions are listed in pel ranges. 5 Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039. 6 To support two‑sided printing, the Universal paper size length must be between 5.83 inches (148 mm) and 17 inches (431.8 mm); and the width must be between 8.27 inches (210 mm) and 11.69 inches (297 mm). Note: The explanation of the printable area assumes that the Print Area menu item is set to Normal. For more information, see “Print Area Menu Item” in the PCL chapter of the Printer Language and Interfaces Technical Reference.
Page 12 of the Lexmark 925dte user manual — Printer Job Language (PJL)
Page 12 · click to enlarge
Page 12

Printer Job Language (PJL) 12

Printer Job Language (PJL)

PJL commands information

Your printer supports complete PJL commands, including certain commands that cause the printer to enter PCL emulation, PostScript emulation, and Personal Printer Data Stream (PPDS).

For a complete listing with descriptions of PJL commands, see the Printer Languages and Interfaces Technical Reference.

To determine which commands your printer supports, see “Appendix B: PJL support” on page 31.

Page 13 of the Lexmark 925dte user manual — Supported paper sizes
Page 13 · click to enlarge
Page 13

PostScript (PS) emulation 13

PostScript (PS) emulation

Your printer supports complete PostScript emulation supplemental operators. For full, detailed descriptions of these operators, see the PostScript emulation chapter of the Printer Languages and Interfaces Technical Reference.

To determine which commands your printer supports, see “Appendix C: PostScript support” on page 81.

Supported paper sizes

X = Not supported

Paper sizes Printer model

Size Literal name Size (mm) Size (inches) Size (points) C925de, C925dte

11 x 17 11x17 279.4 x 431.8 11 x 17 792 x 1224

17 x 11 ledger 431.8 x 279.4 17 x 11 1224 x 792

A3 a3 297 x 420 11.7 x 16.54 842 x 1191

A4 a4 210.0 x 297.0 8.3 x 11.7 595 x 842

A5 a5 148.0 x 210.0 5.83 x 8.27 419 x 595

A6 a6 105.0 x 148.0 4.13 x 5.83 297 x 419

Executive executivepage 184.2 x 266.7 7.25 x 10.5 522 x 756

Folio folio 215.9 x 330.2 8.5 x 13.0 612 x 936

JIS B4 b4* 257 x 364 10.12 x 14.33 729 x 1032

JIS B5 b5* 182.0 x 257.0 7.2 x 10.1 516 x 729

Legal legal 215.9 x 355.6 8.5 x 14.0 612 x 1008

Letter letter 215.9 x 279.4 8.5 x 11.0 612 x 792

Oficio oficio 215.9 x 340.4 8.5 x 13.4 612 x 965 (Lexmark‑unique size)

612 x 972 (official PostScript size)

Statement statement 139.7 x 215.9 5.5 x 8.5 396 x 612

Universal 297 x 1219 11.69 x 48 841.68 x 3456

* This is a Japanese Industry Standard (JIS) paper size. The same named designation is used by the JIS and International Organization for Standardization (ISO) for different paper sizes.

X925de

Page 14 of the Lexmark 925dte user manual — Tray selected with tray operators
Page 14 · click to enlarge
Page 14

PostScript (PS) emulation 14

PostScript paper tray support

When the printer receives one of the operators listed in “Tray selected with tray operators” on page 14, it performs the actions listed in this section. This paper tray selection process ends when a suitable paper source is chosen and paper is fed from this tray.

  • The printer checks the value of manualfeed in statusdict and the ManualFeed page device parameter. If either one is true, then the printer sends a message to load the requested size in the manual feeder or multipurpose feeder.
  • The PageSize Policy is set to 0 by means of setpagedevice .
  • The printer checks the paper size loaded in the current active source to determine if it matches the requested size. If the sizes match, then the paper is fed from the active source.
  • Note: The current active tray is the last source that was selected from the printer control panel or by the printer language.
  • If the requested size and the size loaded in the active source do not match, then the sources are searched in the order defined by the Priority array in the InputAttributes dictionary in the pagedevice dictionary.
  • If the requested media size is not found by the previous search, then the following search order is used: – Tray 1 – Tray 2 – Tray 3 – Multipurpose feeder – Tray 4 – Tray 5
  • If the requested size cannot be located in any automatic source, then a configurationerror is issued and the job is flushed.

For printers that support automatic two‑sided printing (duplexing):

  • Automatic two ‑ sided printing is not supported for custom-size paper or for envelopes in the multipurpose feeder. Automatic two ‑ sided printing is supported from the multipurpose feeder for all other papers.
  • If the paper source is changed before the back side of a two ‑ sided page prints, then a blank back page prints, the paper source changes, and the information for the back side of the page is printed on the front side of a page sent from the new paper source.

When these operators are used, it is equivalent to executing the following PostScript emulation sequence:

>>

where x y are the PageSize in points.

Tray selected with tray operators

Operator Tray selected (corresponding image size is set)

11x17tray Tray with 11 x 17‑size paper

a3tray Tray with A3‑size paper

setpagedevice · C925de, C925dte X925de

Page 15 of the Lexmark 925dte user manual — Envelope sizes supported
Page 15 · click to enlarge
Page 15

PostScript (PS) emulation 15

Lexmark 925dte — PostScript envelope size support diagram (page 15)
Fig. 3 · PostScript envelope size support

PostScript envelope size support

The literal names in “Envelope sizes supported” on page 15 are also supported as operators in userdict. These operators change the image size, but do not change the active paper source. Therefore, when these operators are used, part of the image may be clipped.

When these literal names are used as operators, it is equivalent to executing the following PostScript emulation sequence. The following example uses a 3.875 x 7.5 envelope.

>>setpagedevice

Envelope sizes supported

Lexmark 925dte — Envelope sizes supported diagram (page 15)
Fig. 4 · Envelope sizes supported

Size name Literal name Size (mm) Size (inches) Size (points) C925de, C925dte

7 3/4 3.875x7.5envelope 98.4 x 190.5 3.875 x 7.5 279 x 540

Commercial 9 3.875x8.875envelope 98.4 x 225.4 3.875 x 8.875 279 x 639

Page 16 of the Lexmark 925dte user manual — PostScript envelope tray support
Page 16 · click to enlarge
Page 16

PostScript (PS) emulation 16

Lexmark 925dte — PostScript envelope tray support diagram (page 16)
Fig. 5 · PostScript envelope tray support

Size name Literal name Size (mm) Size (inches) Size (points) C925de, C925dte

Commercial 10 4.125x9.5envelope 104.8 x 241.3 4.125 x 9.5 297 x 684

International B5 176x250envelope 176 x 250 6.93 x 9.84 499 x 708

International C5 162x229envelope 162 x 229 6.38 x 9.01 459 x 649

International DL 110x220envelope 110 x 220 4.33 x 8.66 312 x 624

Other envelope otherenvelope 296.93 x 427.48 11.69 x 16.83 842 x 1212

Literal names supported

Lexmark 925dte — Literal names supported diagram (page 16)
Fig. 6 · Literal names supported

PostScript envelope tray support

If manualfeed in statusdict and the ManualFeed page device parameter are false when the printer receives one of the envelopetray operators listed in “Envelopetray operator selections” on page 17, then the following occurs:

  • The printer sets the PageSize Policy to 0 .
  • The printer checks the active source to see if it matches the requested envelope size. If the sizes match, then the envelope is fed from the active source.
  • Note: The active source is the last source selected from the printer control panel or data stream.
  • If the requested size and the size loaded in the active source do not match, then the sources are searched in the order defined by the Priority array in the InputAttributes dictionary in the pagedevice dictionary.
  • If the requested media size is not found by the previous search, then the following search order is used: – Envelope feeder – Multipurpose feeder
Page 17 of the Lexmark 925dte user manual — Envelopetray operator selections
Page 17 · click to enlarge
Page 17

PostScript (PS) emulation 17

  • If the requested size and type are not available from any automatic source, then you are prompted to load the requested envelope size and type in the manual feed source.
  • If the size is still not available, then a configurationerror is issued, and the print job is flushed.

If manualfeed or ManualFeed is true, then the printer prompts you to load the requested size manually. If no manual feed exists on the printer, then a rangecheck error message is issued.

The envelope tray the printer selects when it receives an envelopetray operator is listed in “Envelopetray operator selections” on page 17. These operators are equivalent to executing the following PostScript emulation sequence:

setpagedevice

where x y are the PageSize in points.

Envelopetray operator selections

Lexmark 925dte — Envelopetray operator selections diagram (page 17)
Fig. 7 · Envelopetray operator selections

Operator Tray selected (corresponding image size is set) C925de, C925dte X925de

110x220envelopetray Tray with 110 x 220‑size envelopes

dlenvelopetray Tray with 110 x 220‑size envelopes

162x229envelopetray Tray with 162 x 229‑size envelopes

c5envelopetray Tray with 162 x 229‑size envelopes

176x250envelopetray Tray with 176 x 250‑size envelopes

b5envelopetray Tray with 176 x 250‑size envelopes

3.875x7.5envelopetray Tray with 3.875 x 7.5‑size envelopes

monarcenvelopetray Tray with 3.875 x 7.5‑size envelopes

3.875x8.875envelopetray Tray with 3.875 x 8.875‑size envelopes

4.125x9.5envelopetray Tray with 4.125 x 9.5‑size envelopes

com10envelopetray Tray with 4.125 x 9.5‑size envelopes

Page 18 of the Lexmark 925dte user manual — Noise emission levels
Page 18 · click to enlarge
Page 18

Printer specifications

Airflow requirement

The room should meet ASHRAE 62—1989 standards.

Noise emission levels

The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.

Lexmark 925dte — Noise emission levels diagram (page 18)
Fig. 8 · Noise emission levels

Printer specifications 18

Page 19 of the Lexmark 925dte user manual — Physical specifications
Page 19 · click to enlarge
Page 19

Electrical specifications

Lexmark 925dte — Electrical specifications diagram (page 19)
Fig. 9 · Electrical specifications

C925 SFP and X925 MFP low‑voltage models 100–127 V at 50–60Hz, nominal

C925 SFP and X925 MFP high‑voltage models

220–240 V at 50–60Hz, nominal (available only in some countries or regions)

Power requirements

The following table specifies the nominal average power requirements for the base configuration, including fuser power.

Lexmark 925dte — Power requirements diagram (page 19)
Fig. 10 · Power requirements

Physical specifications

Single‑function printer dimensions (unpackaged)

Lexmark 925dte — Physical specifications diagram (page 19)
Fig. 11 · Physical specifications

C925de, C925dte 420 mm (16.54 in.) 622 mm (24.49 in.) 557 mm (21.93 in.) 48.3 kg (106.5 lb)

Printer specifications 19

Page 20 of the Lexmark 925dte user manual — Printer air temperature ranges
Page 20 · click to enlarge
Page 20

Multiple‑function printer dimensions (unpackaged)

Lexmark 925dte — Clearance requirements diagram (page 20)
Fig. 12 · Clearance requirements

X925de 771 mm (30.35 in.) 672 mm (26.46 in.) 668 mm (26.30 in.) 79.3 kg (174.8 lb)

Dimensions of the C925 or X925 hardware options (unpackaged)

Lexmark 925dte — Dimensions of the C925 or X925 hardware options (unpackaged) diagram (page 20)
Fig. 13 · Dimensions of the C925 or X925 hardware options (unp…

135 mm (5.32 in.) 590 mm (23.23 in.) 539 mm (21.22 in.) 14 kg (30.8 lb)

Caster base 101.6 mm (4 in.) 685.8 mm (27 in.) 660.4 mm (26 in.) 9 kg (20 lb)

Printer stand 406.4 mm (16 in.) 656.68 mm (25.85 in.) 772.3 mm (27.89 in.) 14.96 kg (33 lb)

Printer dimensions when extensions are in open position

Lexmark 925dte — Printer dimensions when extensions are in open position diagram (page 20)
Fig. 14 · Printer dimensions when extensions are in open posit…

C925de, C925dte 420 mm (16.54 in.) 863.6 mm (34 in.) 938 mm (36.93 in.)

X925de 1066.8 mm (42 in.) 914.4 mm (36 in.) 1049 mm (41.3 in.)

Clearance requirements

Lexmark 925dte — Clearance requirements diagram (page 20)
Fig. 15 · Clearance requirements

Printer model Left side Right side Front Rear Top

100 mm (3.94 in.) 385 mm (15.16 in.) 380 mm (15 in.) 100 mm (3.94 in.) 100 mm (3.94 in.)

Printer model Left side Right side Front Rear Top

X925de 100 mm (3.94 in.) 348 mm (13.7 in.) 282 mm (11.1 in.) 100 mm (3.94 in.) 285 mm (11.22 in.)

Environmental conditions

Printer air temperature ranges

Lexmark 925dte — Printer air temperature ranges diagram (page 20)
Fig. 16 · Printer air temperature ranges

Product operating Print quality assurance Product not operating* Packaged

10.0 to 33.0°C (50 to 91.4°F) 15.0 to 27.0°C (59 to 80.6°F) ‑5 to 40°C (23 to 104°F) ‑40 to 43.3°C (‑40 to 110°F)

X925de 10.0 to 33.0°C (50 to 91.4°F) 15.0 to 27.0°C (59 to 80.6°F) ‑5 to 40°C (23 to 104°F) ‑40 to 43.3°C (‑40 to 110°F)

Printer specifications 20

Page 21 of the Lexmark 925dte user manual — Atmospheric pressure specifications
Page 21 · click to enlarge
Page 21

Values for the ambient operating environment

Lexmark 925dte — Values for the ambient operating environment diagram (page 21)
Fig. 17 · Values for the ambient operating environment

Printer humidity ranges

Lexmark 925dte — Printer humidity ranges diagram (page 21)
Fig. 18 · Printer humidity ranges

Cartridge air temperature ranges

Lexmark 925dte — Cartridge air temperature ranges diagram (page 21)
Fig. 19 · Cartridge air temperature ranges

‑40 to 43.3°C (‑40 to 110°F)

X925de ‑40 to 43.3°C (‑40 to 110°F)

Altitude and atmospheric pressure specifications

Altitude specifications

Lexmark 925dte — Altitude specifications diagram (page 21)
Fig. 20 · Altitude specifications

C925de, C925dte 0–2300 m (7546 ft) Less than 10300 m (34000 ft)

X925de 0–2300 m (7546 ft) Less than 10300 m (34000 ft)

Atmospheric pressure specifications

Lexmark 925dte — Atmospheric pressure specifications diagram (page 21)
Fig. 21 · Atmospheric pressure specifications

Printer specifications 21

Page 22 of the Lexmark 925dte user manual — Appendix A: PCL support
Page 22 · click to enlarge
Page 22
Appendix APCL support 22

Appendix A: PCL support

PCL emulation commands

Lexmark 925dte — Appendix A: PCL support diagram (page 22)
Fig. 22 · Appendix A: PCL support
Page 23 of the Lexmark 925dte user manual — Appendix A: PCL support
Page 23 · click to enlarge
Page 23
Appendix APCL support 23
Lexmark 925dte — Appendix A: PCL support diagram (page 23)
Fig. 23 · Appendix A: PCL support

ESC&l#C Set Vertical Motion Index (VMI)

Page 24 of the Lexmark 925dte user manual — Appendix A: PCL support
Page 24 · click to enlarge
Page 24
Appendix APCL support 24
Lexmark 925dte — Appendix A: PCL support diagram (page 24)
Fig. 24 · Appendix A: PCL support
Page 25 of the Lexmark 925dte user manual — Appendix A: PCL support
Page 25 · click to enlarge
Page 25
Appendix APCL support 25
Lexmark 925dte — Appendix A: PCL support diagram (page 25)
Fig. 25 · Appendix A: PCL support

ESC)#X Select Secondary Download Font (by Font ID)

ESC)s#V Secondary Font Height (Point Size) X X

Page 26 of the Lexmark 925dte user manual — Appendix A: PCL support
Page 26 · click to enlarge
Page 26
Appendix APCL support 26
Lexmark 925dte — Appendix A: PCL support diagram (page 26)
Fig. 26 · Appendix A: PCL support

ESC*l#W[data] Color Lookup Tables X X

ESC*p#X Set Horizontal Cursor Position (in PCL Units)

ESC*p#Y Set Vertical Cursor Position (in PCL Units)

Page 27 of the Lexmark 925dte user manual — Appendix A: PCL support
Page 27 · click to enlarge
Page 27
Appendix APCL support 27
Lexmark 925dte — Appendix A: PCL support diagram (page 27)
Fig. 27 · Appendix A: PCL support

ESC%‑12345X Universal Exit Language (UEL) / Start of PJL

Page 28 of the Lexmark 925dte user manual — GL/2 commands
Page 28 · click to enlarge
Page 28
Appendix APCL support 28

GL/2 commands

Lexmark 925dte — GL/2 commands diagram (page 28)
Fig. 28 · GL/2 commands
Page 29 of the Lexmark 925dte user manual — GL/2 commands
Page 29 · click to enlarge
Page 29
Appendix APCL support 29
Lexmark 925dte — GL/2 commands diagram (page 29)
Fig. 29 · GL/2 commands
Page 30 of the Lexmark 925dte user manual — GL/2 commands
Page 30 · click to enlarge
Page 30
Appendix APCL support 30
Lexmark 925dte — GL/2 commands diagram (page 30)
Fig. 30 · GL/2 commands
Page 31 of the Lexmark 925dte user manual — Common variables for both printer languages
Page 31 · click to enlarge
Page 31

Common variables for both printer languages

Lexmark 925dte — Common variables for both printer languages diagram (page 31)
Fig. 31 · Common variables for both printer languages
Page 32 of the Lexmark 925dte user manual — PJL messages for auto-continuable conditions
Page 32 · click to enlarge
Page 32
Lexmark 925dte — USTATUS unsolicited status variables diagram (page 32)
Fig. 32 · USTATUS unsolicited status variables

USTATUS unsolicited status variables

Lexmark 925dte — USTATUS unsolicited status variables diagram (page 32)
Fig. 33 · USTATUS unsolicited status variables

PJL messages for auto-continuable conditions

Lexmark 925dte — PJL messages for auto-continuable conditions diagram (page 32)
Fig. 34 · PJL messages for auto-continuable conditions

30016 37 Insufficient memory, some Held Jobs were deleted

30016 37 Insufficient memory, some Held Jobs were deleted

Page 33 of the Lexmark 925dte user manual — USTATUS unsolicited status variables
Page 33 · click to enlarge
Page 33
Lexmark 925dte — USTATUS unsolicited status variables diagram (page 33)
Fig. 35 · USTATUS unsolicited status variables

30016 37 Insufficient memory, some Held Jobs will not be restored

30016 37 Insufficient memory for Flash Memory Defragment operation

30016 57 Configuration change, some held jobs were not restored

Held Jobs May Not Be Restored (57 Configuration Change)

30016 37 Insufficient memory, some held jobs will not be restored

30017 39 Complex page, some data may not have printed

Page 34 of the Lexmark 925dte user manual — USTATUS unsolicited status variables
Page 34 · click to enlarge
Page 34
Lexmark 925dte — USTATUS unsolicited status variables diagram (page 34)
Fig. 36 · USTATUS unsolicited status variables
Page 35 of the Lexmark 925dte user manual — USTATUS unsolicited status variables
Page 35 · click to enlarge
Page 35
Lexmark 925dte — USTATUS unsolicited status variables diagram (page 35)
Fig. 37 · USTATUS unsolicited status variables

30076 35 Insufficient memory to support Resource Save feature

30076 35 Insufficient memory to support Resource Save feature

Page 36 of the Lexmark 925dte user manual — USTATUS unsolicited status variables
Page 36 · click to enlarge
Page 36
Lexmark 925dte — USTATUS unsolicited status variables diagram (page 36)
Fig. 38 · USTATUS unsolicited status variables
Page 37 of the Lexmark 925dte user manual — USTATUS unsolicited status variables
Page 37 · click to enlarge
Page 37
Lexmark 925dte — USTATUS unsolicited status variables diagram (page 37)
Fig. 39 · USTATUS unsolicited status variables

32002 52 Not enough free space in flash memory for resources

Page 38 of the Lexmark 925dte user manual — USTATUS unsolicited status variables
Page 38 · click to enlarge
Page 38
Lexmark 925dte — USTATUS unsolicited status variables diagram (page 38)
Fig. 40 · USTATUS unsolicited status variables

40048 [Pick up text from 'data1' and 'data2 but not 'userMessage1' and 'userMessage2']

40049 [Pick up text from 'data1' and 'data2' but not 'userMessage1' and 'userMessage2']

Page 39 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 39 · click to enlarge
Page 39
Lexmark 925dte — PJL messages for attendance conditions diagram (page 39)
Fig. 41 · PJL messages for attendance conditions

PJL messages for attendance conditions

Lexmark 925dte — PJL messages for attendance conditions diagram (page 39)
Fig. 42 · PJL messages for attendance conditions

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 40 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 40 · click to enlarge
Page 40
Lexmark 925dte — PJL messages for attendance conditions diagram (page 40)
Fig. 43 · PJL messages for attendance conditions

40019 Remove originals from the scanner automatic document feeder

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 41 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 41 · click to enlarge
Page 41
Lexmark 925dte — PJL messages for attendance conditions diagram (page 41)
Fig. 44 · PJL messages for attendance conditions

40021 Cover Open, Close Top Covers, Close Door, or Insert Cartridge

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 42 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 42 · click to enlarge
Page 42
Lexmark 925dte — PJL messages for attendance conditions diagram (page 42)
Fig. 45 · PJL messages for attendance conditions

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 43 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 43 · click to enlarge
Page 43
Lexmark 925dte — PJL messages for attendance conditions diagram (page 43)
Fig. 46 · PJL messages for attendance conditions

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 44 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 44 · click to enlarge
Page 44
Lexmark 925dte — PJL messages for attendance conditions diagram (page 44)
Fig. 47 · PJL messages for attendance conditions

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 45 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 45 · click to enlarge
Page 45
Lexmark 925dte — PJL messages for attendance conditions diagram (page 45)
Fig. 48 · PJL messages for attendance conditions

Intervention Required - 84 Black Photo Dev Life Warning

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 46 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 46 · click to enlarge
Page 46
Lexmark 925dte — PJL messages for attendance conditions diagram (page 46)
Fig. 49 · PJL messages for attendance conditions

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 47 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 47 · click to enlarge
Page 47
Lexmark 925dte — PJL messages for attendance conditions diagram (page 47)
Fig. 50 · PJL messages for attendance conditions

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 48 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 48 · click to enlarge
Page 48
Lexmark 925dte — PJL messages for attendance conditions diagram (page 48)
Fig. 51 · PJL messages for attendance conditions

40129 84.xx Replace [color] imaging unit and [color] cartridge

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 49 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 49 · click to enlarge
Page 49
Lexmark 925dte — PJL messages for attendance conditions diagram (page 49)
Fig. 52 · PJL messages for attendance conditions

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 50 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 50 · click to enlarge
Page 50
Lexmark 925dte — PJL messages for attendance conditions diagram (page 50)
Fig. 53 · PJL messages for attendance conditions

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 51 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 51 · click to enlarge
Page 51
Lexmark 925dte — PJL messages for attendance conditions diagram (page 51)
Fig. 54 · PJL messages for attendance conditions

40309 32.xx Black cartridge part number unsupported by device

40310 32.xx Cyan cartridge part number unsupported by device

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 52 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 52 · click to enlarge
Page 52
Lexmark 925dte — PJL messages for attendance conditions diagram (page 52)
Fig. 55 · PJL messages for attendance conditions

40311 32.xx Magenta cartridge part number unsupported by device

40312 32.xx Yellow cartridge part number unsupported by device

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 53 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 53 · click to enlarge
Page 53
Lexmark 925dte — PJL messages for attendance conditions diagram (page 53)
Fig. 56 · PJL messages for attendance conditions

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 54 of the Lexmark 925dte user manual — PJL messages for attendance conditions
Page 54 · click to enlarge
Page 54
Lexmark 925dte — PJL messages for attendance conditions diagram (page 54)
Fig. 57 · PJL messages for attendance conditions

40409 30.xx Missing black cartridge and/or black imaging unit

40410 30.xx Missing cyan cartridge and/or cyan imaging unit

40411 30.xx Missing magenta cartridge and/or magenta imaging unit

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

Page 55 of the Lexmark 925dte user manual — PJL messages for paper handling
Page 55 · click to enlarge
Page 55
Lexmark 925dte — PJL messages for paper handling diagram (page 55)
Fig. 58 · PJL messages for paper handling

40412 30.xx Missing yellow cartridge and/or yellow imaging unit

Intervention Required - Insert Duplex Pages in Tray [x]

* This message contains a subset of letters CMYK, where CMYK denotes Cyan, Magenta, Yellow, and Black cartridges, respectively.

PJL messages for paper handling

Lexmark 925dte — PJL messages for paper handling diagram (page 55)
Fig. 59 · PJL messages for paper handling
Page 56 of the Lexmark 925dte user manual — PJL messages for paper handling
Page 56 · click to enlarge
Page 56
Lexmark 925dte — PJL messages for paper handling diagram (page 56)
Fig. 60 · PJL messages for paper handling
Page 57 of the Lexmark 925dte user manual — PJL messages for paper handling
Page 57 · click to enlarge
Page 57
Lexmark 925dte — PJL messages for paper handling diagram (page 57)
Fig. 61 · PJL messages for paper handling

41xyy Load [paper source] with [paper type] [paper size]

41xyy Load Manual Feeder with [paper type] [paper size]

Page 58 of the Lexmark 925dte user manual — PJL messages for paper handling
Page 58 · click to enlarge
Page 58
Lexmark 925dte — PJL messages for paper handling diagram (page 58)
Fig. 62 · PJL messages for paper handling

41xyy Load single sheet feeder with [Custom Type Name]

41xyy Load single sheet feeder with [paper type] [paper size]

41xyy Change [paper source] to [Custom Type Name], load [orientation]

41xyy Change [paper source] to [Custom String] load [orientation]

41xyy Change [paper source] to [paper type] [paper size]

Page 59 of the Lexmark 925dte user manual — PJL messages for paper handling
Page 59 · click to enlarge
Page 59
Lexmark 925dte — PJL messages for paper handling diagram (page 59)
Fig. 63 · PJL messages for paper handling

41xyy Change [paper source] to [paper type] [paper size] load [orientation]

41xxy Load Manual Feeder with [paper type] [paper size]

Page 60 of the Lexmark 925dte user manual — PJL messages for paper jams
Page 60 · click to enlarge
Page 60

PJL messages for paper jams

Lexmark 925dte — PJL messages for paper jams diagram (page 60)
Fig. 64 · PJL messages for paper jams

w indicates that this message includes a letter indicating a door or cover that needs to be opened.

x represents the number of jammed pages in the printer. y represents the tray number.

Page 61 of the Lexmark 925dte user manual — PJL messages for paper jams
Page 61 · click to enlarge
Page 61
Lexmark 925dte — PJL messages for paper jams diagram (page 61)
Fig. 65 · PJL messages for paper jams

w indicates that this message includes a letter indicating a door or cover that needs to be opened.

x represents the number of jammed pages in the printer.

Page 62 of the Lexmark 925dte user manual — PJL messages for paper jams
Page 62 · click to enlarge
Page 62
Lexmark 925dte — PJL messages for paper jams diagram (page 62)
Fig. 66 · PJL messages for paper jams

w indicates that this message includes a letter indicating a door or cover that needs to be opened.

x represents the number of jammed pages in the printer.

Page 63 of the Lexmark 925dte user manual — PJL messages for paper jams
Page 63 · click to enlarge
Page 63
Lexmark 925dte — PJL messages for paper jams diagram (page 63)
Fig. 67 · PJL messages for paper jams

w indicates that this message includes a letter indicating a door or cover that needs to be opened.

x represents the number of jammed pages in the printer.

Page 64 of the Lexmark 925dte user manual — PJL messages for paper jams
Page 64 · click to enlarge
Page 64
Lexmark 925dte — PJL messages for paper jams diagram (page 64)
Fig. 68 · PJL messages for paper jams

w indicates that this message includes a letter indicating a door or cover that needs to be opened.

x represents the number of jammed pages in the printer.

Page 65 of the Lexmark 925dte user manual — PJL messages for paper jams
Page 65 · click to enlarge
Page 65
Lexmark 925dte — PJL messages for paper jams diagram (page 65)
Fig. 69 · PJL messages for paper jams

w indicates that this message includes a letter indicating a door or cover that needs to be opened.

x represents the number of jammed pages in the printer.

Page 66 of the Lexmark 925dte user manual — Lexmark ‑ unique PJL commands
Page 66 · click to enlarge
Page 66
Lexmark 925dte — Service errors diagram (page 66)
Fig. 70 · Service errors

w indicates that this message includes a letter indicating a door or cover that needs to be opened.

x represents the number of jammed pages in the printer.

Service errors

Lexmark 925dte — Service errors diagram (page 66)
Fig. 71 · Service errors

Device attendance messages

Lexmark 925dte — Device attendance messages diagram (page 66)
Fig. 72 · Device attendance messages

Lexmark ‑ unique PJL commands

These commands are Lexmark extensions which have been added to the PJL command set to provide the user with remote control of many printer functions.

Lexmark 925dte — Lexmark ‑ unique PJL commands diagram (page 66)
Fig. 73 · Lexmark ‑ unique PJL commands
Page 67 of the Lexmark 925dte user manual — File and device protection commands
Page 67 · click to enlarge
Page 67
Lexmark 925dte — File and device protection commands diagram (page 67)
Fig. 74 · File and device protection commands

File and device protection commands

Lexmark 925dte — File and device protection commands diagram (page 67)
Fig. 75 · File and device protection commands
Page 68 of the Lexmark 925dte user manual — Appendix C: PostScript support
Page 68 · click to enlarge
Page 68
Appendix CPostScript support 81

Appendix C: PostScript support

Supplemental operators

Lexmark 925dte — Appendix C: PostScript support diagram (page 68)
Fig. 76 · Appendix C: PostScript support
Page 69 of the Lexmark 925dte user manual — Appendix C: PostScript support
Page 69 · click to enlarge
Page 69
Appendix CPostScript support 82
Lexmark 925dte — Appendix C: PostScript support diagram (page 69)
Fig. 77 · Appendix C: PostScript support
Page 70 of the Lexmark 925dte user manual — Appendix C: PostScript support
Page 70 · click to enlarge
Page 70
Appendix CPostScript support 83
Lexmark 925dte — Appendix C: PostScript support diagram (page 70)
Fig. 78 · Appendix C: PostScript support
Page 71 of the Lexmark 925dte user manual — Page device parameters
Page 71 · click to enlarge
Page 71
Appendix CPostScript support 84
Lexmark 925dte — Page device parameters diagram (page 71)
Fig. 79 · Page device parameters

Page device parameters

Lexmark 925dte — Page device parameters diagram (page 71)
Fig. 80 · Page device parameters
Page 72 of the Lexmark 925dte user manual — Page device parameters
Page 72 · click to enlarge
Page 72
Appendix CPostScript support 85
Lexmark 925dte — Page device parameters diagram (page 72)
Fig. 81 · Page device parameters
Page 73 of the Lexmark 925dte user manual — Page device parameters
Page 73 · click to enlarge
Page 73
Appendix CPostScript support 86
Lexmark 925dte — Page device parameters diagram (page 73)
Fig. 82 · Page device parameters
Page 74 of the Lexmark 925dte user manual — Page device parameters
Page 74 · click to enlarge
Page 74
Appendix CPostScript support 87
Lexmark 925dte — Page device parameters diagram (page 74)
Fig. 83 · Page device parameters
Page 75 of the Lexmark 925dte user manual — User interpreter parameters
Page 75 · click to enlarge
Page 75
Appendix CPostScript support 88
Lexmark 925dte — User interpreter parameters diagram (page 75)
Fig. 84 · User interpreter parameters

User interpreter parameters

Lexmark 925dte — User interpreter parameters diagram (page 75)
Fig. 85 · User interpreter parameters
Page 76 of the Lexmark 925dte user manual — System interpreter parameters
Page 76 · click to enlarge
Page 76
Appendix CPostScript support 89
Lexmark 925dte — System interpreter parameters diagram (page 76)
Fig. 86 · System interpreter parameters

System interpreter parameters

Lexmark 925dte — System interpreter parameters diagram (page 76)
Fig. 87 · System interpreter parameters
Page 77 of the Lexmark 925dte user manual — System interpreter parameters
Page 77 · click to enlarge
Page 77
Appendix CPostScript support 90
Lexmark 925dte — System interpreter parameters diagram (page 77)
Fig. 88 · System interpreter parameters
Page 78 of the Lexmark 925dte user manual — System interpreter parameters
Page 78 · click to enlarge
Page 78
Appendix CPostScript support 91
Lexmark 925dte — System interpreter parameters diagram (page 78)
Fig. 89 · System interpreter parameters
Page 79 of the Lexmark 925dte user manual — Devices supported
Page 79 · click to enlarge
Page 79
Appendix CPostScript support 92
Lexmark 925dte — Devices supported diagram (page 79)
Fig. 90 · Devices supported

Devices supported

Lexmark 925dte — Devices supported diagram (page 79)
Fig. 91 · Devices supported
Page 80 of the Lexmark 925dte user manual — Devices supported
Page 80 · click to enlarge
Page 80
Appendix CPostScript support 93
Lexmark 925dte — Devices supported diagram (page 80)
Fig. 92 · Devices supported
Page 81 of the Lexmark 925dte user manual — Device parameters
Page 81 · click to enlarge
Page 81
Appendix CPostScript support 94
Lexmark 925dte — Device parameters diagram (page 81)
Fig. 93 · Device parameters

Device parameters

Lexmark 925dte — Device parameters diagram (page 81)
Fig. 94 · Device parameters

Device Parameters for the Communication Device %Parallel%, %ParallelA%, %ParallelB%, %ParallelC%, %ParallelD%

Page 82 of the Lexmark 925dte user manual — Device parameters
Page 82 · click to enlarge
Page 82
Appendix CPostScript support 95
Lexmark 925dte — Device parameters diagram (page 82)
Fig. 95 · Device parameters

Device Parameters for the Communication Device %Serial%, %SerialA%, %SerialB%, %SerialC%, %SerialD%

Device Parameters for the Communication Device %LocalTalk%, %LocalTalkA%, %LocalTalkB%, %LocalTalkC%, %LocalTalkD%

Page 83 of the Lexmark 925dte user manual — Device parameters
Page 83 · click to enlarge
Page 83
Appendix CPostScript support 96
Lexmark 925dte — Device parameters diagram (page 83)
Fig. 96 · Device parameters

Device Parameters for the Communication Device %EtherTalk%, %EtherTalkA%, %EtherTalkB%, %EtherTalkC%, %EtherTalkD%

Device Parameters for the Communication Device %IR%, %IR_A%, %IR_B%, %IR_C%, %IR_D%

Page 84 of the Lexmark 925dte user manual — Device parameters
Page 84 · click to enlarge
Page 84
Appendix CPostScript support 97
Lexmark 925dte — Device parameters diagram (page 84)
Fig. 97 · Device parameters

Device Parameters for the Communication Device %USB%, %USB_A%, %USB_B%, %USB_C%, %USB_D%

Device Parameters for the Communication Device %TokenTalk%, %TokenTalkA%, %TokenTalkB%, %TokenTalkC%, %TokenTalkD%

Page 85 of the Lexmark 925dte user manual — Device parameters
Page 85 · click to enlarge
Page 85
Appendix CPostScript support 98
Lexmark 925dte — Device parameters diagram (page 85)
Fig. 98 · Device parameters

Device Parameters for the Communication Device %AppSocket%, %AppSocketA%, %AppSocketB%, %AppSocketC%, %AppSocketD%

Device Parameters for the Communication Device %RemotePrinter%, %RemotePrinterA%, %RemotePrinterB%, %RemotePrinterC%, %RemotePrinterD%

Device Parameters for the Communication Device %PrintServer%, PrintServerA%, PrintServerB%, %PrintServerC%, %PrintServerD%

Page 86 of the Lexmark 925dte user manual — Device parameters
Page 86 · click to enlarge
Page 86
Appendix CPostScript support 99
Lexmark 925dte — Device parameters diagram (page 86)
Fig. 99 · Device parameters

Device Parameters for the Communication Device %LPR%, %LPR_A%, %LPR_B%, %LPR_C%, %LPR_D%

Device Parameters for the Communication Device %LexLink%, %LexLinkA%, %LexLinkB%, %LexLinkC%, %LexLinkD%

Device Parameters for the Communication Device %IP%, %IP_A%, %IP_B%, %IP_C%, %IP_D%

Page 87 of the Lexmark 925dte user manual — Device parameters
Page 87 · click to enlarge
Page 87
Appendix CPostScript support 100
Lexmark 925dte — Device parameters diagram (page 87)
Fig. 100 · Device parameters

Device Parameters for the Communication Device %EthernetPhysical%, %EthernetPhysicalA%, %EthernetPhysicalB%, %EthernetPhysicalC%, %EthernetPhysicalD%

Device Parameters for the Communication Device %TokenRingPhysical%, %TokenRingPhysicalA%, %TokenRingPhysicalB%, %TokenRingPhysicalC%, %TokenRingPhysicalD%

Page 88 of the Lexmark 925dte user manual — Device parameters
Page 88 · click to enlarge
Page 88
Appendix CPostScript support 101
Lexmark 925dte — Device parameters diagram (page 88)
Fig. 101 · Device parameters

Device Parameters for the Parameters Device %Calendar%, %CalendarA%, %CalendarB%, %CalendarC%, %CalendarD%

Page 89 of the Lexmark 925dte user manual — Device parameters
Page 89 · click to enlarge
Page 89
Appendix CPostScript support 102
Lexmark 925dte — Device parameters diagram (page 89)
Fig. 102 · Device parameters
Page 90 of the Lexmark 925dte user manual — PostScript message keys commands
Page 90 · click to enlarge
Page 90
Appendix CPostScript support 103

PostScript message keys commands

Key C925de, C925dte X925de

job · status · source

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Lexmark 925dte

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lexmark 925dte

Be the first to ask — other owners or our team will answer.

Original document

Lexmark 925dte manual PDF

105 pages·2.7 MB·Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…