EN
Lexmark logo
Official user manual

Lexmark 840

119 pages·2.7 MB·Printer·PDF·ENDEFRITNLJA
Lexmark 840
Table of Contents 126 sections Contents · Learning about the printer · Printer overview · Basic model · … ShowHide
Contentsp.3Learning about the printerp.6Printer overviewp.6Basic modelp.6Configured modelp.7Understanding the printer operator panelp.9Installing drivers for local printingp.11Windowsp.11Using Windows Server 2003, Windows2000, WindowsXP, Windows98SE, WindowsMe, or WindowsNTp.11Using Windows 95 and Windows 98 (first edition)p.12Serial printingp.13Macintoshp.15Creating a queue in Print Center / Printer Setup Utility (MacOSX)p.15UNIX/Linuxp.16Installing drivers for network printingp.17Printing a network setup pagep.17Assigning a printer IP addressp.17Verifying the IP settingsp.18Windowsp.18Supported printer driversp.18Supported network printer portsp.18Direct printing using Windows98SE, Me, WindowsNT4.0, Windows2000, WindowsXP, or WindowsSer...p.19Shared printing using WindowsNT 4.0, Windows2000, WindowsXP, or WindowsServer2003p.20Configuring Drag‘N’Printp.21Macintoshp.22Mac OS Xp.22MacOS9.xp.23UNIX/Linuxp.24NetWarep.24Installing optionsp.25Accessing the printer system boardp.26Installing a printer memory cardp.28Installing a flash memory or firmware cardp.29Installing an optioncardp.30Installing a hard diskp.32Replacing the access panelp.34Understanding paper and specialty media guidelinesp.35Supported print mediap.35Selecting print mediap.42Paperp.42Transparenciesp.45Envelopesp.45Labelsp.46Card stockp.47Storing print mediap.47Avoiding jamsp.47Printingp.49Loading standard or optional 500-sheet traysp.49Loading the multipurpose feederp.52Loading the 2000-sheet dual input traysp.55Loading the 2000-sheet high capacity feederp.56Loading Letter or A4 size print media in the short-edge feed orientationp.58Setting up trays with different orientationsp.58Linking traysp.59Identifying and linking output binsp.60Linking output binsp.60Sending a job to printp.61Printing from a USB flash memory devicep.62Canceling a print jobp.63Canceling a job from the printer operator panelp.63Canceling a job from a computer running Windowsp.63Canceling a job from a Macintosh computerp.64Printing the menu settings pagep.64Printing a network setup pagep.65Printing a font sample listp.65Printing a directory listp.65Printing confidential and held jobsp.65Printing a confidential jobp.65Printing and deleting held jobsp.67Printing A5/Statement or JIS-B5/Executive sizesp.69Maintaining the printerp.70Storing suppliesp.70Determining the status of suppliesp.70Photoconductor kit end-of-lifep.71Conserving suppliesp.71Ordering suppliesp.71Ordering a toner cartridgep.71Ordering a photoconductor kitp.71Maintenance kitp.72Ordering staple cartridgesp.72Recycling Lexmark productsp.72Clearing jamsp.73Identifying jamsp.73Access doors and traysp.74Understanding jam messagesp.75Clearing printer jamsp.75250 Paper Jam Check MP Feederp.7524x Paper Jam Check Tray <x>p.76200, 201, and 202 Paper Jam Check Door Ap.79203 Paper Jam Check <Areas A/E>p.80230 Paper Jam Check Door <A, E, D>p.82231 Paper Jam Check <A, D>p.84Clearing Area Bp.85Clearing Area Cp.8828x Paper Jam Check Finisherp.90Clearing staple jamsp.92Troubleshootingp.94Online customer supportp.94Calling for servicep.94Checking an unresponsive printerp.94Printing multiple-language PDFsp.95Solving printing problemsp.95Solving option problemsp.97Solving 2000-sheet drawer problemsp.98Solving paper feed problemsp.99Solving print quality problemsp.100Administrative supportp.104Adjusting operator panel brightness and contrastp.104Disabling operator panel menusp.104Enabling operator panel menusp.105Restoring factory default settingsp.105Adjusting Power Saverp.106Disabling Power Saverp.106Encrypting the diskp.107Setting security using the Embedded Web Server (EWS)p.108Setting the system passwordp.108Using the secure Embedded Web Serverp.108Supporting SNMPv3 (Simple Network Management Protocol version 3)p.108Supporting IPSec (Internet Protocol Security)p.109Using Secure modep.109Using 802.1x Authenticatingp.110Locking the operator panel menusp.110Printing Lockoutp.111Confidential Print Setupp.111Noticesp.112Indexp.117
Page 1 of the Lexmark 840 user manual — W840
Page 1 · click to enlarge
Page 1

W840

User’s Guide

March 2005

www.lexmark.com

Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. © 2005 Lexmark International, Inc. All rights reserved. 740 West New Circle Road Lexington, Kentucky 40550

Page 2 of the Lexmark 840 user manual — Safety information
Page 2 · click to enlarge
Page 2

Edition: March 2005

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time. Comments about this publication may be addressed to Lexmark International, Inc., Department F95/032-2, 740 West New Circle Road, Lexington, Kentucky 40550, U.S.A. In the United Kingdom and Eire, send to Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. You can purchase additional copies of publications related to this product by calling 1-800-553-9727. In the United Kingdom and Eire, call +44 (0)8704 440 044. In other countries, contact your point of purchase. References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility. © 2005 Lexmark International, Inc. All rights reserved. UNITED STATES GOVERNMENT RIGHTS This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.

Trademarks

Lexmark, Lexmark with diamond design, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. Drag’N’Print and PrintCryption are trademarks of Lexmark International, Inc. PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and the printer emulates the functions corresponding to the commands. PostScript® is a registered trademark of Adobe Systems Incorporated. PostScript 3 is Adobe Systems’ designation of a set of printer commands (language) and functions included in its software products. This printer is intended to be compatible with the PostScript 3 language. This means the printer recognizes PostScript 3 commands used in various application programs, and the printer emulates the functions corresponding to the commands. Details relating to compatibility are included in the Technical Reference. Other trademarks are the property of their respective owners.

Safety information

  • Connect the power cord to a properly grounded electrical outlet that is near the product and easily accessible. CAUTION: Do not set up this product or make any electrical or cabling connections, such as the power cord or telephone, during a lightning storm.
  • Refer service or repairs, other than those described in the operating instructions, to a professional service person.
  • This product is designed, tested, and approved to meet strict global safety standards with the use of specific Lexmark components. The safety features of some parts may not always be obvious. Lexmark is not responsible for the use of other replacement parts.
  • Your product uses a laser. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
  • Your product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
Page 3 of the Lexmark 840 user manual — Table of Contents
Page 3 · Contents
Contents

Contents

Contentsp.3Learning about the printerp.6Printer overviewp.6Basic modelp.6Configured modelp.7Understanding the printer operator panelp.9Installing drivers for local printingp.11Windowsp.11Using Windows Server 2003, Windows2000, WindowsXP, Windows98SE, WindowsMe, or WindowsNTp.11Using Windows 95 and Windows 98 (first edition)p.12Serial printingp.13Macintoshp.15Creating a queue in Print Center / Printer Setup Utility (MacOSX)p.15UNIX/Linuxp.16Installing drivers for network printingp.17Printing a network setup pagep.17Assigning a printer IP addressp.17Verifying the IP settingsp.18Windowsp.18Supported printer driversp.18Supported network printer portsp.18Direct printing using Windows98SE, Me, WindowsNT4.0, Windows2000, WindowsXP, or WindowsSer...p.19Shared printing using WindowsNT 4.0, Windows2000, WindowsXP, or WindowsServer2003p.20Configuring Drag‘N’Printp.21Macintoshp.22Mac OS Xp.22MacOS9.xp.23UNIX/Linuxp.24NetWarep.24Installing optionsp.25Accessing the printer system boardp.26Installing a printer memory cardp.28Installing a flash memory or firmware cardp.29Installing an optioncardp.30Installing a hard diskp.32Replacing the access panelp.34Understanding paper and specialty media guidelinesp.35Supported print mediap.35Selecting print mediap.42Paperp.42Transparenciesp.45Envelopesp.45Labelsp.46Card stockp.47Storing print mediap.47Avoiding jamsp.47Printingp.49Loading standard or optional 500-sheet traysp.49Loading the multipurpose feederp.52Loading the 2000-sheet dual input traysp.55Loading the 2000-sheet high capacity feederp.56Loading Letter or A4 size print media in the short-edge feed orientationp.58Setting up trays with different orientationsp.58Linking traysp.59Identifying and linking output binsp.60Linking output binsp.60Sending a job to printp.61Printing from a USB flash memory devicep.62Canceling a print jobp.63Canceling a job from the printer operator panelp.63Canceling a job from a computer running Windowsp.63Canceling a job from a Macintosh computerp.64Printing the menu settings pagep.64Printing a network setup pagep.65Printing a font sample listp.65Printing a directory listp.65Printing confidential and held jobsp.65Printing a confidential jobp.65Printing and deleting held jobsp.67Printing A5/Statement or JIS-B5/Executive sizesp.69Maintaining the printerp.70Storing suppliesp.70Determining the status of suppliesp.70Photoconductor kit end-of-lifep.71Conserving suppliesp.71Ordering suppliesp.71Ordering a toner cartridgep.71Ordering a photoconductor kitp.71Maintenance kitp.72Ordering staple cartridgesp.72Recycling Lexmark productsp.72Clearing jamsp.73Identifying jamsp.73Access doors and traysp.74Understanding jam messagesp.75Clearing printer jamsp.75250 Paper Jam Check MP Feederp.7524x Paper Jam Check Tray <x>p.76200, 201, and 202 Paper Jam Check Door Ap.79203 Paper Jam Check <Areas A/E>p.80230 Paper Jam Check Door <A, E, D>p.82231 Paper Jam Check <A, D>p.84Clearing Area Bp.85Clearing Area Cp.8828x Paper Jam Check Finisherp.90Clearing staple jamsp.92Troubleshootingp.94Online customer supportp.94Calling for servicep.94Checking an unresponsive printerp.94Printing multiple-language PDFsp.95Solving printing problemsp.95Solving option problemsp.97Solving 2000-sheet drawer problemsp.98Solving paper feed problemsp.99Solving print quality problemsp.100Administrative supportp.104Adjusting operator panel brightness and contrastp.104Disabling operator panel menusp.104Enabling operator panel menusp.105Restoring factory default settingsp.105Adjusting Power Saverp.106Disabling Power Saverp.106Encrypting the diskp.107Setting security using the Embedded Web Server (EWS)p.108Setting the system passwordp.108Using the secure Embedded Web Serverp.108Supporting SNMPv3 (Simple Network Management Protocol version 3)p.108Supporting IPSec (Internet Protocol Security)p.109Using Secure modep.109Using 802.1x Authenticatingp.110Locking the operator panel menusp.110Printing Lockoutp.111Confidential Print Setupp.111Noticesp.112Indexp.117
Page 6 of the Lexmark 840 user manual — Basic model
Page 6 · click to enlarge
Page 6

1 Learning about the printer

Conventions used in this book

Printer overview

telephone, during a lightning storm.

Basic model

The following illustration shows a printer with its base features.

Tray 1 and Tray 2 (500-sheet trays)

Learning about the printer

Standard output bin · Operator panel · Multipurpose feeder

Page 7 of the Lexmark 840 user manual — Learning about the printer
Page 7 · click to enlarge
Page 7

Learning about the printer

Configured model

The following illustration shows a fully configured printer. Items denoted with an asterisk (*) are options.

Bridge unit assembly* (used in conjunction with finisher)

Exit 2* (used in conjunction with

Lexmark 840 — Learning about the printer diagram (page 7)
Fig. 1 · Learning about the printer

duplex unit and finisher)

Tray 5* (2000-sheet high

Tray 3 and Tray 4* (500-sheet trays or 2000-sheet dual input trays)

Operator panel · capacity feeder) · Printer overview

Page 8 of the Lexmark 840 user manual — Paper Menu
Page 8 · click to enlarge
Page 8

Learning about the printer

A number of menus are available to make it easy for you to change printer settings. The diagram shows the menu index on the operator panel and the menus and items available under each menu. For more information about menus and menu items, see the Menus and Messages book on the publications CD.

Menu

Paper Menu

Reports

Settings

Paper Menu Default Source Paper Size/Type Configure MP Substitute Size Paper Texture Paper Loading Custom Types Universal Setup Bin Setup

Reports Menu Settings Page Device Statistics Network Setup Page Network [x] Setup Page Profiles List Print Quick Ref NetWare Setup Page Print Fonts Print Directory

Settings Setup Menu Finishing Menu Quality Menu Utilities Menu PDF Menu PostScript Menu PCL Emul Menu HTML Menu Image Menu

Network/Ports TCP/IP IPv6 Standard Network Network [x] Standard USB USB [x] Front USB Parallel Parallel [x] Serial [x] NetWare AppleTalk LexLink

Security Max Invalid PIN Job Expiration

Help Print All Print Quality Printing Guide Supplies Guide Media Guide Print Defects Menu Map Information Guide Connection Guide Moving Guide

Printer overview

Page 9 of the Lexmark 840 user manual — Learning about the printer
Page 9 · click to enlarge
Page 9

Learning about the printer

Understanding the printer operator panel

The operator panel consists of these items:

  • A 4-line, back-lit, gray-scale display that can show both graphics and text
  • Eight buttons: Back, Menu, Stop, Select ( ), , , , and
  • Indicator light
  • Numeric pad
  • USB Direct Interface
Lexmark 840 — Learning about the printer diagram (page 9)
Fig. 2 · Learning about the printer

USB Direct interface Select button

Stop Navigation buttons Numeric pad

The use of the buttons and the layout of the display panel are described in the following table.

Button or operator panel itemFunction BackPress the Back button to return to the last screen you viewed. Note: Changes made on a screen will not be applied if you press the Back button. MenuPress the Menu button to open the menu index. Note: The printer must be in the Ready state to access the menu index. A message indicating the menus are unavailable will appear if the printer is not ready. StopPress the Stop button to stop the mechanical operation of the printer. After pressing Stop, the message Stopping appears. When the printer has stopped, the status line in the operator panel will show Stopped, and a list of options will appear. Navigation buttonsThe Up or Down buttons are used to move up and down lists. When navigating through a list using the Up or Down button, the cursor moves one line at a time. Pressing the Down button at the bottom of the screen changes the screen to the next whole page. The Left or Right buttons are used to move within a screen such as moving from one menu index item to another. They are also used to scroll through text that will not fit on the screen. The Select button is used to initiate action on a selection. Press Select when the cursor appears next to the selection you want such as following a link, submitting a configuration item, or when you want to start or cancel a job.

Understanding the printer operator panel

Display

Page 10 of the Lexmark 840 user manual — Learning about the printer
Page 10 · click to enlarge
Page 10

Learning about the printer

Button or operator panel itemFunction Indicator lightA two-toned LED is used on the operator panel, one color being green and the other being red. The lights indicate whether the printer power is on, the printer is busy, idle, processing a job, or requires operator intervention. Status Indicates Off Power is off Solid green Printer is on, but idle Flashing green Printer is warming up, processing data, or printing a job Solid red Operator intervention is required Numeric pad 1 2 3 4 5 6 7 8 9 0 #The numeric pad consists of numbers, a pound '#' sign, and a backspace button. The 5 button has a raised bump for non-visual orientation. The numbers are used to enter numeric values for items like quantities or PINs. The backspace is used to delete the number to the left of the cursor. Pressing the backspace multiple times will delete additional entries. Note: The pound '#' sign is not used. Display 250 Paper JamThe display shows messages and graphics describing the current state of the printer and indicating possible printer problems you must resolve. The top line of the display is the header line. If applicable, it will contain the graphic indicating the Back button can be used. It will also display the current status and the Supplies (Warnings) status. If multiple warnings are present, each warning will be separated by a comma. The other three lines of the display are the body of the screen. This is where you view printer status, supplies messages, show-me screens, and make selections.
StatusIndicates OffPower is off Solid greenPrinter is on, but idle Flashing greenPrinter is warming up, processing data, or printing a job Solid redOperator intervention is required
Lexmark 840 — Learning about the printer diagram (page 10)
Fig. 3 · Learning about the printer
Lexmark 840 — Learning about the printer diagram (page 10)
Fig. 4 · Learning about the printer
Lexmark 840 — Learning about the printer diagram (page 10)
Fig. 5 · Learning about the printer

Understanding the printer operator panel

Page 11 of the Lexmark 840 user manual — Windows
Page 11 · click to enlarge
Page 11

2 Installing drivers for local printing

A local printer is a printer attached to the computer using a USB or parallel cable. The local printer is intended to be used by the computer to which it is attached. If attaching a local printer, install the printer driver on the computer before setting up the printer.

The printer driver is software that lets the computer communicate with the printer.

The procedure to install drivers depends on the operating system used. Use the following table to find driver installation instructions for the particular operating system. For additional help, see the documentation that shipped with the computer and the software.

Operating systemGo to page Windows11 Windows Server 2003, Windows 2000, Windows XP, Windows 98 SE, Windows Me, Windows NT 4.x11 Windows 95 and Windows 98 (first edition)12 Serial printing13 Macintosh15 UNIX/Linux16

Windows

Some Windows operating systems may already include a printer driver that is compatible with the printer.

and appear in the Printers folder.

Use the drivers CD that shipped with the printer to install the custom printer driver and obtain enhanced printer features and functionality.

Drivers are also available in downloadable software packages on the Lexmark Web site at www.lexmark.com.

Using Windows Server 2003, Windows 2000, Windows XP, Windows 98 SE, Windows Me, or Windows NT

1 Insert the drivers CD.

If the CD does not launch automatically, click Start Æ Run, and type D:\Setup.exe in the Run dialog (where D is the letter of the CD-ROM drive).

Installing drivers for local printing

Page 12 of the Lexmark 840 user manual — Using Windows 95 and Windows 98 (first edition)
Page 12 · click to enlarge
Page 12

Installing drivers for local printing

2 Click Install Printer and Software.

drivers on the computer.

3 Click Agree to accept the license agreement.

4 Select Suggested, and click Next.

The Suggested option is the default installation for local and network-attached setup. To install utilities, change settings, or customize device drivers, select Custom, and follow the instructions on the screen.

5 Select Local Attach, and click Finish.

Follow the instructions on the screen. It may take some time for the drivers to load.

6 Close the drivers CD installer application.

7 Connect the USB cable, and turn on the printer.

The Plug and Play screen appears, and a printer object is created in the printers folder of the computer.

Using Windows 95 and Windows 98 (first edition)

1 Turn on the computer.

2 Insert the drivers CD. If the CD launches automatically, click Exit to return to the Add Printer Wizard.

3 Click Start Æ Settings Æ Printers, and double-click Add Printer.

4 When prompted, select Local printer.

5 Click Have Disk.

drivers on the computer.

6 Specify the location of the custom printer driver on the drivers CD.

The path should be similar to the following:

D:\Drivers\Print\Win_9xMe\<language>

Where D is the letter of the CD-ROM drive.

7 Click OK.

It may take some time for the drivers to load.

8 Close the drivers CD.

Windows

Page 13 of the Lexmark 840 user manual — Installing a printer driver
Page 13 · click to enlarge
Page 13

Installing drivers for local printing

Serial printing

With serial printing, data is transferred one bit at a time. Although serial printing is usually slower than parallel printing, it is the preferred option when there is a great deal of distance between the printer and computer, or when a parallel interface is not available.

Before printing, establishing communication between the printer and computer is required. To do this:

1 Set serial parameters in the printer.

2 Install a printer driver on the attached computer.

3 Match the serial settings in the COM port.

Setting parameters in the printer

1 Press on the operator panel.

2 Press until Network/Ports appears, and then press .

3 Press until Serial Option X appears, and then press .

4 Press until <Parameter> appears, and then press (where <Parameter> is the parameter required for a change).

5 Press until <Setting> appears, and then press (where <Setting> is the setting required for a change).

  • Maximum baud rate supported is 115,200.
  • Data Bits must be set to 7 or 8.
  • Parity must be set to Even, Odd, or None.
  • Stop Bits must be set to 2.
  • Flow Control recommended protocol setting is Xon/Xoff.

6 Press repeatedly to return the printer to the Ready state.

7 Print a Menu Settings page, and verify that the serial parameters are correct.

a Press on the operator panel.

b Press until Reports appears, and then press .

c Press until Menu Settings Page appears, and then press .

d Look under the Standard Serial (or Serial Option X if a serial interface card is installed) heading to find the serial parameters.

Installing a printer driver

A printer driver must be installed on the computer that is connected to the printer.

1 Insert the drivers CD. It should launch automatically. If the CD does not launch automatically, click Start Æ Run, and type the following in the Run dialog:

D:\Setup.exe

Where D is the letter of the CD-ROM drive.

Windows

Page 14 of the Lexmark 840 user manual — Setting parameters in the communications (COM) port
Page 14 · click to enlarge
Page 14

Installing drivers for local printing

2 Click Install Printer and Software.

3 Click Agree to accept the Printer Software License Agreement.

4 Select Custom, and click Next.

5 Select Components, and click Next.

6 Select Local, and click Next.

7 Select the printer from the list, and click Add Printer.

8 Expand the printer item listed below Selected Components.

9 Click PORT: <LPT1>, and select the communications port (COM1 or COM2) needed for use.

10 Click Finish to complete the printer software installation.

Setting parameters in the communications (COM) port

After the printer driver is installed, the serial parameters must be set for the communications port assigned to the printer driver.

The serial parameters in the communications port must match exactly to the serial parameters set in the printer.

1 Click Start Æ Settings Æ Control Panel, and double-click System.

2 On the Device Manager tab, click + to expand the list of available ports.

3 Select the communications port assigned to the printer (COM1 or COM2).

4 Click Properties.

5 On the Port Settings tab, set the serial parameters to the exact same serial parameters in the printer.

Look for the printer settings under the Serial Standard (or Serial Option X) heading on the Menu Settings page printed previously.

6 Click OK, and close all the windows.

7 Print a test page to verify printer installation.

a Click Start Æ Settings Æ Printers.

b Select the printer just added.

c Click File Æ Properties.

d Click Print Test Page. When a test page prints successfully, printer setup is complete.

Windows

Page 15 of the Lexmark 840 user manual — ` Creating a desktop printer icon (Mac OS 9.x)
Page 15 · click to enlarge
Page 15

Installing drivers for local printing

Macintosh

Mac OS 9.x or later is required for USB printing. To print locally to a USB-attached printer, create a desktop printer icon (Mac OS 9) or create a queue in Print Center / Printer Setup Utility (Mac OS X).

Creating a queue in Print Center / Printer Setup Utility (Mac OS X)

1 Install a PostScript Printer Description (PPD) file on the computer.

a Insert the drivers CD.

b Double-click the installer package for the printer.

c Click Continue on the Welcome screen and again after viewing the Readme file.

d Click Continue after viewing the license agreement, and click Agree to accept the terms of the agreement.

e Select a Destination, and click Continue.

f On the Easy Install screen, click Install.

g Enter the user password, and click OK. All the necessary software is installed on the computer.

h Click Close when installation is complete.

2 Open Finder, click Applications, and click Utilities.

3 Double-click Print Center or Printer Setup Utility.

at www.lexmark.com.

4 Do one of the following:

  • If the USB-attached printer appears in the Printer List, quit Print Center or Printer Setup Utility. A queue has been created for the printer.
  • If the USB-attached printer does not appear in the Printer List, make sure the USB cable is properly connected and the printer is turned on. After the printer appears in the Printer List, quit Print Center or Printer Setup Utility.

` Creating a desktop printer icon (Mac OS 9.x)

1 Install a PostScript Printer Description (PPD) file on the computer.

a Insert the drivers CD.

b Double-click Classic, and double-click the installer package for the printer.

c Choose the language needed for use, and click Continue.

d Click Continue after viewing the Readme file.

e Click Continue after viewing the license agreement, and click Agree to accept the terms of the agreement.

f On the Easy Install screen, click Install. All the necessary files are installed on the computer.

g Click Close when installation is complete.

at www.lexmark.com.

Macintosh

Page 16 of the Lexmark 840 user manual — UNIX/Linux
Page 16 · click to enlarge
Page 16

Installing drivers for local printing

2 Do one of the following:

  • For Mac OS 9.0 : Open Apple LaserWriter .
  • For Mac OS 9.1 – 9.x : Open Applications , and click Utilities .

3 Double-click Desktop Printer Utility.

4 Select Printer (USB), and click OK.

5 In the USB Printer Selection section, click Change.

If the printer does not appear in the USB Printer Selection list, make sure the USB cable is properly connected, and the printer is turned on.

6 Select the name of the printer, and click OK. The printer appears in the original Printer (USB) window.

7 In the PostScript Printer Description (PPD) File section, click Auto Setup. Make sure the printer PPD now matches the printer in use.

8 Click Create, and click Save.

9 Specify a printer name, and click Save. The printer is now saved as a desktop printer.

UNIX/Linux

Local printing is supported on many UNIX and Linux platforms, such as Sun Solaris and Red Hat.

The Sun Solaris and Linux packages are available on the drivers CD and on the Lexmark Web site at www.lexmark.com. The UNIX/Linux User’s Guide in each package gives detailed instructions for installing and using Lexmark printers in UNIX and Linux environments.

All the printer driver packages support local printing using a parallel connection. The driver package for Sun Solaris supports USB connections to Sun Ray appliances and Sun workstations.

Visit the Lexmark Web site at www.lexmark.com for a complete list of supported UNIX and Linux platforms.

UNIX/Linux

Page 17 of the Lexmark 840 user manual — Assigning a printer IP address
Page 17 · click to enlarge
Page 17

3 Installing drivers for network printing

Printing a network setup page

If the printer is attached to a network, print a network setup page on the printer to verify the network connection. This page also provides important information that helps in configuring for network printing.

1 Make sure the printer is on.

2 Press on the operator panel.

3 Press until Reports appears, and then press .

4 Press until Network Setup Page appears, and then press .

5 Check the first section on the network setup page, and confirm that Status is “Connected.”

If Status is “Not Connected” the LAN drop may not be active, or the network cable may be malfunctioning. Consult a system support person for a solution, and print another network setup page to verify that the printer is connected to the network.

Assigning a printer IP address

If the network is using DHCP, an IP address is automatically assigned after connecting the network cable to the printer.

1 Look for the address under the “TCP/IP” heading on the network setup page printed in Printing a network setup page.

2 Go to Verifying the IP settings, and begin with step 2.

If the network is not using DHCP, then manually assign an IP address to the printer. One of the easiest ways is to use the operator panel:

1 Press on the operator panel.

2 Press until Network/Ports appears, and then press .

3 Press until TCP/IP appears, and then press .

Standard Network appears if the printer has a network port on the printer system board. If an internal print server is installed in the option card, Network Option 1 appears.

4 Press until Address appears, and then press .

5 Using the numeric pad, enter the IP address. Once the address is entered, press .

Submitting Selection appears briefly.

6 Press until Netmask appears, and then press .

7 Using the numeric pad, enter the IP address. Once the address is entered, press .

Submitting Selection appears briefly.

8 Press until Gateway appears, and then press .

Installing drivers for network printing

Page 18 of the Lexmark 840 user manual — Supported network printer ports
Page 18 · click to enlarge
Page 18

Installing drivers for network printing

9 Using the numeric pad, enter the IP address. Once the address is entered, press .

Submitting Selection appears briefly.

10 Press repeatedly until the printer returns to Ready.

Verifying the IP settings

1 Print another network setup page. Look under the “TCP/IP” heading, and make sure the IP address, netmask, and gateway are correct. See Printing a network setup page on page 17 if help is needed.

2 Ping the printer, and verify that it responds. At a command prompt on a network computer, type ping followed by the new printer IP address (for example, 192.168.0.11).

Command prompt if using Windows 2000).

If the printer is active on the network, a reply is sent.

After the TCP/IP settings are assigned and verified, install the printer on each network computer.

Windows

In Windows environments, network printers can be configured for direct printing or shared printing. Both network printing methods require the installation of a printer driver and the creation of a network printer port.

Supported printer drivers

  • Windows system printer driver
  • Lexmark custom printer driver

System drivers are built into Windows operating systems. Custom drivers are available on the drivers CD.

Updated system and custom drivers are available on the Lexmark Web site at www.lexmark.com.

Supported network printer ports

  • Microsoft Standard TCP/IP port—Windows 2000, Windows XP, and Windows Server 2003
  • LPR—Windows NT 4.0
  • Lexmark Enhanced TCP/IP port—Windows 98 SE/Me, Windows NT 4.0, Windows 2000, Windows XP, and Windows Server 2003

For basic printer functionality, install a system printer driver and use a system network printer port, such as an LPR or a Standard TCP/IP port. The system printer driver and port allow for a consistent user interface for use with all the printers on the network. However, using a custom printer driver and network port provides enhanced functionality, such as printer status alerts.

Verifying the IP settings

Page 19 of the Lexmark 840 user manual — Installing drivers for network printing
Page 19 · click to enlarge
Page 19

Installing drivers for network printing

Follow the steps for the printing configuration and operating system in use to configure the network printer:

Printing configuration Operating system Go to page

  • Direct
  • Printer is connected directly to the network using a network cable, such as Ethernet.
  • Printer drivers are typically installed on each network computer.

Windows 98 SE, Windows NT 4.0, Windows Me, Windows 2000, Windows XP, or Windows Server 2003

  • Shared
  • Printer is connected to one of the computers on the network using a local cable, such as USB.
  • Printer drivers are installed on the computer attached to the printer.
  • During driver installation, the printer is set up to be “shared” so that other network computers can print to it.

Windows NT 4.0, Windows 2000, Windows XP, or Windows Server 2003

Direct printing using Windows 98 SE, Me, Windows NT 4.0, Windows 2000, Windows XP, or Windows Server 2003

To install a custom printer driver and network port:

1 Launch the drivers CD.

2 Click Install Printer and Software.

3 Click Agree to accept the license agreement.

4 Select Suggested, and click Next.

5 Select Network Attach, and click Next.

6 Select the printer model from the list, and click Next.

7 Select the printer port from the list, and click Finish to complete the installation.

If the printer port is not listed:

a Click Add Port.

b Select Lexmark Enhanced TCP/IP Port, and enter the information to create the port.

c Enter a port name.

This can be any name to associate with the printer, such as Color1-lab4. After the port is created, this name appears in the list of available ports.

d Enter the IP address in the text box.

help, see Printing a network setup page and Verifying the IP settings.

8 Print a test page to verify printer installation.

Printer · Clients · Windows

Page 20 of the Lexmark 840 user manual — Installing drivers for network printing
Page 20 · click to enlarge
Page 20

Installing drivers for network printing

Shared printing using Windows NT 4.0, Windows 2000, Windows XP, or Windows Server 2003

After connecting the printer to a Windows NT 4.0, Windows 2000, Windows XP, or Windows Server 2003 computer (which will act as a server), follow these steps to configure the network printer for shared printing:

1 Install a custom printer driver.

a Launch the drivers CD.

b Click Install Printer and Software.

c Click Agree to accept the license agreement.

d Select Suggested, and click Next.

The Suggested option is the default installation for local and network-attached setup. To install utilities, change settings, or customize device drivers, select Custom, and follow the instructions on the screen.

e Select Local Attach, and click Finish.

Follow the instructions on the screen. It may take some time for the drivers to load.

f Close the drivers CD installer application.

g Connect the USB cable, and turn on the printer.

The Plug and Play screen appears, and a printer object is created in the Printers folder of the computer. The printer is shared in step 2: “Share the printer on the network.”

h Print a test page to verify printer installation.

2 Share the printer on the network.

a Click Start Æ Settings Æ Printers.

b Select the printer just added.

c Click File Æ Sharing.

d Select the Shared as check box, and enter a name in the text box.

e In the Alternate Drivers section, select the operating systems of all the network clients that will print to the printer.

f Click OK.

g Check the following to make sure the printer was successfully shared.

  • The printer object in the Printers folder now has a shared indicator. For example, in Windows NT 4.0, a hand appears under the printer object.
  • Browse Network Neighborhood. Find the host name of the server, and look for the shared name assigned to the printer.
Show 4 more labels / short text on this page
Server · Printer · Clients · Windows
Page 21 of the Lexmark 840 user manual — Configuring Drag‘N’Print
Page 21 · click to enlarge
Page 21

Installing drivers for network printing

Install the printer driver (or subset) on network clients

Using the point and print method

the print job processing. This lets network clients return to applications much faster.

With this method, a subset of driver information is copied from the server to the client computer. This is just enough information to send a print job to the printer.

1 Double-click Network Neighborhood on the Windows desktop of the client computer.

2 Locate the host name of the server computer, and double-click the host name.

3 Right-click the shared printer name, and click Install.

Wait a few minutes for the driver information to be copied from the server computer to the client computer and for a new printer object to be added to the Printers folder. The time this takes varies based on network traffic and other factors.

4 Close Network Neighborhood.

5 Print a test page to verify printer installation.

Using the peer-to-peer method

With this method, the printer driver is fully installed on each client computer. Network clients retain control of driver modifications. The client computer handles the print job processing.

1 Click Start Æ Settings Æ Printers.

2 Click Add Printer to launch the Add Printer wizard.

3 Click Next.

4 Click Network Printer, and click Next.

5 Enter the printer name or URL (if on the Internet or an intranet), and click Next.

If the printer name or URL is unknown, leave the text box blank, and click Next.

6 Select the network printer from the Shared printers list. If the printer is not listed, enter the path of the printer in the text box.

The path looks similar to the following:

\\<server host name>\<shared printer name>

provide a path to available drivers.

The server host name is the name of the server computer that identifies it to the network. The shared printer name is the name assigned during the server installation process.

7 Click OK.

8 Select whether this printer will be the default printer for the client, and click Finish.

9 Print a test page to verify printer installation.

Configuring Drag‘N’Print

For detailed configuration instructions, launch the drivers CD, click View Documentation, and click Software and utilities.

Windows

Page 22 of the Lexmark 840 user manual — Using AppleTalk Printing
Page 22 · click to enlarge
Page 22

Installing drivers for network printing

Macintosh

printer to UNIX or Macintosh computers.

To print to a network printer, each Macintosh user must install a custom PostScript Printer Description (PPD) file, and either create a desktop printer on the computer (Mac OS 9.x) or create a print queue in Print Center (Mac OS X).

Mac OS X

Step 1: Install a custom PPD file

1 Install a PostScript Printer Description (PPD) file on the computer.

a Insert the drivers CD.

b Double-click the installer package for the printer.

c Click Continue on the Welcome screen and again after viewing the Readme file.

d Click Continue after viewing the license agreement, and click Agree to accept the terms of the agreement.

e Select a Destination, and click Continue.

f On the Easy Install screen, click Install.

g Enter the user password, and click OK. All the necessary software is installed on the computer.

h Click Close when installation is complete.

2. Create a print queue in Print Center or Printer Setup Utility

Using AppleTalk Printing

Follow these steps to create a print queue using AppleTalk Printing.

1 Open Finder, click Applications, and click Utilities.

2 Double-click Print Center or Printer Setup Utility.

3 Choose Add Printer from the “Printers” menu.

4 Choose AppleTalk from the pop-up menu.

select.

5 Select the AppleTalk zone from the list.

6 Select the new printer from the list, and click Add.

7 Verify printer installation:

a Open Finder, click Applications, and click TextEdit.

b Choose Print from the “File” menu.

c Choose Summary from the “Copies & Pages” pop-up menu.

to know which printer to select.

Macintosh

Page 23 of the Lexmark 840 user manual — Mac OS 9.x
Page 23 · click to enlarge
Page 23

Installing drivers for network printing

  • If the PPD file displayed in the Summary window is correct for the printer, then printer setup is complete.
  • If the PPD file displayed in the Summary window is not correct for the printer, delete the printer from the printer list in Print Center or Printer Setup Utility, and repeat Step 1: Install a custom PPD file .

Using IP Printing

Follow these steps to create a print queue using IP Printing. To create an AppleTalk print queue, see Step 2: Create a print queue in Print Center or Printer Setup Utility.

1 Open Finder, click Applications, and click Utilities.

2 Double-click Print Center or Printer Setup Utility.

3 Choose Add Printer from the “Printers” menu.

4 Choose IP Printing from the pop-up menu.

5 Enter the IP address or the printer DNS name in the Printer Address box.

6 Choose Lexmark from the “Printer Model” pop-up menu.

7 Select the new printer from the list, and click Add.

8 Verify printer installation:

a Open Finder, click Applications, and click TextEdit.

b Choose Print from the “File” menu.

c Choose Summary from the “Copies & Pages” pop-up menu.

d Do one of the following:

  • If the PPD file displayed in the Summary window is correct for the printer, then printer setup is complete.
  • If the PPD file displayed in the Summary window is not correct for the printer, delete the printer from the printer list in Print Center or Printer Setup Utility, and repeat Step 1: Install a custom PPD file .

Mac OS 9.x

Step 1: Install a custom PPD file

1 Insert the drivers CD.

a Double-click Classic, and double-click the installer package for the printer.

b Choose the language needed for use, and click Continue.

c Click Continue after viewing the Readme file.

d Click Continue after viewing the license agreement, and click Agree to accept the terms of the agreement.

e On the Easy Install screen, click Install. All the necessary files are installed on the computer.

f Click Close when installation is complete.

at www.lexmark.com.

Macintosh

Page 24 of the Lexmark 840 user manual — NetWare
Page 24 · click to enlarge
Page 24

Installing drivers for network printing

Step 2: Create a desktop printer

1 In the Chooser, select the LaserWriter 8 driver.

2 For a routed network, select the default zone from the list. For the zone to select, look on the Network Setup page under AppleTalk for Zone.

3 Select the new printer from the list.

4 For printer to select, look on the Network Setup page under the “AppleTalk” heading to find the default name of the printer.

5 Click Create.

6 Make sure there is an icon next to the printer name in the Chooser.

7 Close the Chooser window.

8 Verify printer installation.

a Click the desktop printer icon just added.

b Choose Printing Æ Change Setup.

– If the PPD file displayed in the PostScript Printer Description (PPD) file portion of the menu is correct for the printer, printer setup is complete. – If the PPD file displayed in the PostScript Printer Description (PPD) file portion of the menu is not correct for the printer, repeat Step 1: Install a custom PPD file.

UNIX/Linux

The printer supports many UNIX and Linux platforms, such as Sun Solaris and Red Hat. Visit the Lexmark Web site at www.lexmark.com for a complete list of supported UNIX and Linux platforms.

www.lexmark.com.

We provide a printer driver package for each supported UNIX and Linux platform. The User’s Guide in each package gives detailed instructions for installing and using Lexmark printers in UNIX and Linux environments.

These packages are available for download from the Lexmark Web site. The driver package needed is also on the drivers CD.

NetWare

The printer supports Novell Distributed Print Services (NDPS/iPrint). For the latest information about installing a network printer in a NetWare environment, launch the drivers CD, and click View Documentation.

UNIX/Linux

Page 25 of the Lexmark 840 user manual — 4 Installing options
Page 25 · click to enlarge
Page 25

4 Installing options

and unplug the power cord before continuing.

You can customize the printer memory capacity and connectivity by adding optional cards. The instructions in this section help you install any of the following options:

  • Memory cards – Printer memory – Flash memory
  • Firmware cards – Bar Code – Forms – IPDS and SCS/TNe – PRESCRIBE – PrintCryption™
  • Other options – Printer hard disk – External Serial Adapter – Tri-Port Adapter – Infrared Adapter – USB/Parallel 1284-C interface card – Coax/Twinax Adapter – Internal print servers (also called internal network adapters or INAs)

Installing options

Page 26 of the Lexmark 840 user manual — Installing options
Page 26 · click to enlarge
Page 26

Installing options

Accessing the printer system board

You must access the printer system board to install printer memory, flash memory, a hard disk, or an option card.

1 Loosen the screws on the access panel located on the back side of the printer.

Lexmark 840 — Installing options diagram (page 26)
Fig. 6 · Installing options

2 Remove the panel from the printer, and set it aside.

Lexmark 840 — Installing options diagram (page 26)
Fig. 7 · Installing options

Accessing the printer system board

Page 27 of the Lexmark 840 user manual — Installing options
Page 27 · click to enlarge
Page 27

Installing options

Use the illustration to locate the connector for the option you want to install.

Lexmark 840 — Installing options diagram (page 27)
Fig. 8 · Installing options

Flash memory or firmware card connectors

Printer memory card connector

Accessing the printer system board

Hard disk connector · Option card connector

Page 28 of the Lexmark 840 user manual — Installing options
Page 28 · click to enlarge
Page 28

Installing options

Installing a printer memory card

Complete the following instructions to install a printer memory card.

1 Remove the system board access panel. (See Accessing the printer system board.)

2 Push open the latches on both ends of the memory card connector.

3 Unpack the memory card.

printer frame before you touch a memory card.

Avoid touching the connection points along the edge of the card. Save the packaging.

4 Align the notches on the bottom of the card with the notches on the connector.

5 Push the memory card firmly into the connector until the latches on either end of the connector snap into place.

It may require some force to fully seat the card.

Lexmark 840 — Installing options diagram (page 28)
Fig. 9 · Installing options

6 Make sure each latch fits over the notch on the end of the card.

Installing a printer memory card

Page 29 of the Lexmark 840 user manual — Installing options
Page 29 · click to enlarge
Page 29

Installing options

Installing a flash memory or firmware card

1 Remove the system board access panel. (See Accessing the printer system board.)

2 Unpack the flash memory or firmware card.

such as the printer frame before you touch a card.

3 Holding the flash memory or firmware card by the locking clips, align the plastic pins on the card with the holes on the system board.

4 Push the flash memory or firmware card firmly into place, and release the locking clips.

The entire length of the connector on the flash memory or firmware card must touch the system board and be locked into the connector.

Be careful not to damage the connectors.

Lexmark 840 — Installing options diagram (page 29)
Fig. 10 · Installing options

Installing a flash memory or firmware card

Page 30 of the Lexmark 840 user manual — Installing options
Page 30 · click to enlarge
Page 30

Installing options

Installing an option card

frame before you touch a memory card.

1 Remove the system board access panel. (See Accessing the printer system board.)

2 Open the system board door.

Lexmark 840 — Installing options diagram (page 30)
Fig. 11 · Installing options

3 Locate the card connector on the system board.

4 Remove the screws and the cover plate, and save them.

Lexmark 840 — Installing options diagram (page 30)
Fig. 12 · Installing options
Lexmark 840 — Installing options diagram (page 30)
Fig. 13 · Installing options

5 Unpack the card. Save the packaging materials.

Installing an option card

Page 31 of the Lexmark 840 user manual — Installing options
Page 31 · click to enlarge
Page 31

Installing options

6 Align the connection points on the card with the connector on the system board, and push the card firmly into the system board connector.

Lexmark 840 — Installing options diagram (page 31)
Fig. 14 · Installing options

7 Insert the screws saved from the cover plate (or the extra screws shipped with the card).

8 Tighten the screws to secure the card.

Lexmark 840 — Installing options diagram (page 31)
Fig. 15 · Installing options

Installing an option card

Page 32 of the Lexmark 840 user manual — Installing options
Page 32 · click to enlarge
Page 32

Installing options

Installing a hard disk

1 Remove the system board access panel. (See Accessing the printer system board.)

2 Remove the mounting plate, hard disk, ribbon cable, and attachment screws from the package.

3 Align the ribbon cable connector with the connector pins on the hard disk.

4 Attach the ribbon cable to the hard disk.

5 Align the screw holes on the mounting plate with the holes in the hard disk.

6 Secure the mounting plate to the hard disk with the screws.

Installing a hard disk

Hard disk · Ribbon cable

Page 33 of the Lexmark 840 user manual — Installing options
Page 33 · click to enlarge
Page 33

Installing options

7 Press the ribbon cable connector into the connector on the system board.

Lexmark 840 — Installing options diagram (page 33)
Fig. 16 · Installing options

8 Press the three posts on the mounting plate into the holes on the system board. The hard disk snaps into place.

Lexmark 840 — Installing options diagram (page 33)
Fig. 17 · Installing options

Installing a hard disk

Page 34 of the Lexmark 840 user manual — Installing options
Page 34 · click to enlarge
Page 34

Installing options

Replacing the access panel

After you have installed options on the printer system board, follow these steps to reattach the access panel.

1 Align the tabs on the right side of the access panel with the slots on the printer.

2 Slide the panel to the right and towards the printer.

Lexmark 840 — Installing options diagram (page 34)
Fig. 18 · Installing options
Lexmark 840 — Installing options diagram (page 34)
Fig. 19 · Installing options

3 Tighten the screws.

Lexmark 840 — Installing options diagram (page 34)
Fig. 20 · Installing options

4 Plug the printer power cord back into a properly grounded electrical outlet and turn on the printer.

Replacing the access panel

Page 35 of the Lexmark 840 user manual — Supported print media
Page 35 · click to enlarge
Page 35

5 Understanding paper and specialty media guidelines

Print media is paper, card stock, transparencies, labels, and envelopes. The last four are sometimes referred to as specialty media. The printer provides high quality printing on a variety of media. A number of things must be considered concerning media before printing. This chapter provides information on making media selections and caring for media.

  • Supported print media
  • Selecting print media
  • Storing print media
  • Avoiding jams

For more details about the types of paper and specialty media your printer supports, see the Card Stock & Label Guide available on our Lexmark Web site at www.lexmark.com.

We recommend that you try a limited sample of any paper or specialty media you are considering using with the printer before purchasing large quantities.

Supported print media

The following tables provide information on standard and optional sources for both input and output trays and bins.

  • Print media sizes
  • Media sizes supported in the finisher
  • Feed characteristics by print media size
  • Print media types
  • Print media weights
  • Media weights supported in the finisher

Understanding paper and specialty media guidelines

Page 36 of the Lexmark 840 user manual — Print media sizes
Page 36 · click to enlarge
Page 36

Understanding paper and specialty media guidelines

Print media sizes

— indicates support

500-sheet trays (standard and option)

300-sheet second exit output bin3

2000-sheet dual input trays (option)

500-sheet standard output bin

2000-sheet high capacity feeder

Print media size Dimensions

A3 297 x 420 mm (11.7 x 16.5 in.)

A4 210 x 297 mm (8.27 x 11.7 in.)

A51 148 x 210 mm (5.83 x 8.27 in.)

JIS B4 257 x 364 mm (10.1 x 14.3 in.)

JIS B51 182 x 257 mm (7.17 x 10.1 in.)

Letter 215.9 x 279.4 mm (8.5 x 11 in.)

Legal 215.9 x 355.6 mm (8.5 x 14 in.)

Executive1 184.2 x 266.7 mm (7.25 x 10.5 in.)

Folio 216 x 330 mm (8.5 x 13 in.)

Statement1 139.7 x 215.9 mm (5.5 x 8.5 in.)

Tabloid 279 x 432 mm (11.0 x 17.0 in.)

Universal2 98.4 x 89.0 mm to 297.0 x 431.8 mm (3.9 x 3.5 in. to 11.7 x 17.0 in.)

7 ¾ Envelope 98.4 x 190.5 mm (3.875 x 7.5 in.)

10 Envelope 104.8 x 241.3 mm (4.12 x 9.5 in.)

DL Envelope 110 x 220 mm (4.33 x 8.66 in.)

C5 Envelope 162 x 229 mm (6.38 x 9.01 in.)

98.4 x 89.0 mm to 297.0 x 431.8 mm (3.9 x 3.5 in. to 11.7 x 17.0 in.)

1 These sizes may not appear in the Paper Size menu until Auto Size Sensing is changed. See Printing A5/Statement or JIS-B5/Executive sizes on page 69 for more information. 2 This size setting formats the page for 297.0 x 431.8 mm (11.7 x 17.0 in.) unless the size is specified by the software application. 3 This output bin is only available when the finisher is installed.

Show 7 more labels / short text on this page
Multipurpose feeder · Duplex unit · (option) · (option) · Other Envelope · · Supported print media
Page 37 of the Lexmark 840 user manual — A3
Page 37 · click to enlarge
Page 37

Understanding paper and specialty media guidelines

Media sizes supported in the finisher

Bin 1 Bin 2

Standard* Offset Staple Punch Standard* Offset Staple Punch

A3

A4

A5

JIS B4

JIS B5

Letter

Legal

Executive

Folio

Tabloid

* Paper passes to the finisher bin without being stapled or offset.

Show 9 more labels / short text on this page
Size · Statement · Universal · 7 ¾ Envelope · 10 Envelope · DL Envelope · C5 Envelope · Other Envelope · Supported print media
Page 38 of the Lexmark 840 user manual — Feed characteristics by print media size
Page 38 · click to enlarge
Page 38

Understanding paper and specialty media guidelines

Feed characteristics by print media size

Print media size Feed orientation1 Print media orientation2 Size supports duplex

A3 Portrait Short-edge

A4 Portrait or Landscape Short-edge or Long-edge

A5 Portrait Short-edge

JIS B4 Portrait Short-edge

JIS B5 Landscape Long-edge

Letter Portrait or Landscape Short-edge or Long-edge

Legal Portrait Short-edge

Executive Landscape Long-edge

Folio Portrait Short-edge

Statement Portrait Short-edge

Tabloid Portrait Short-edge

Universal Portrait3 Short-edge

7 ¾ Envelope Landscape Long-edge

10 Envelope Landscape Long-edge

DL Envelope Landscape Long-edge

C5 Envelope Landscape Long-edge

Other Envelope Portrait Short-edge

1 Feed orientation indicates how the printer will place the image on the page, not whether the physical page will be short- edge or long-edge oriented. 2 Short-edge Printing must be enabled for the printer to recognize letter or A4 size print media loaded in the short-edge orientation. For more information, see Loading Letter or A4 size print media in the short-edge feed orientation on page 58. 3 The feed orientation for Universal is actually variable.

Supported print media

Page 39 of the Lexmark 840 user manual — Print media types
Page 39 · click to enlarge
Page 39

Understanding paper and specialty media guidelines

Print media types

2000-sheet dual input trays

Second exit output bin

2000-sheet high capacity feeder

Paper

Card stock

Transparencies

Paper labels

Bond

Envelope

Letterhead

Preprinted

Colored paper

Show 11 more labels / short text on this page
Finisher · Multipurpose feeder · Standard output bin · 500-sheet trays · Duplex unit · Hole Punch · Standard · Stapled · Offset · Print media · Supported print media
Page 40 of the Lexmark 840 user manual — Print media weights
Page 40 · click to enlarge
Page 40

Understanding paper and specialty media guidelines

Print media weights

2000-sheet high capacity feeder

2000-sheet dual input trays

Paper Xerographic or business paper

  • Tray 1 : 64 to 105 g/m 2 grain long (17 to 28 lb bond)
  • Other 500-sheet trays : 64 to 216 g/m 2 grain long (17 to 58 lb bond)

64 to 216 g/m2 grain long (17 to 58 lb bond)

64 to 105 g/m2 grain long (17 to 28 lb bond)

Card stock— maximum (grain long)1

Index Bristol 163 g/m2 (90 lb) 120 g/m2 (67 lb)

Tag 163 g/m2 (100 lb) 120 g/m2 (74 lb)

Cover 176 g/m2 (65 lb) 135 g/m2 (50 lb)

Card stock— maximum (grain short)1

Index Bristol 199 g/m2 (110 lb) 163 g/m2 (90 lb)

Tag 203 g/m2 (125 lb) 163 g/m2 (100 lb)

Cover 216 g/m2 (80 lb) 176 g/m2 (65 lb)

Transparencies Laser printer 138 to 146 g/m2 (37 to 39 lb bond)

138 to 146 g/m2 (37 to 39 lb bond)

Labels Paper 180 g/m2 (48 lb bond)

163 g/m2 (43 lb bond)

Integrated forms Pressure- sensitive area (must enter the printer first)

135 to 140 g/m2 (36 to 37 lb bond)

135 to 140 g/m2 (36 to 37 lb bond)

Paper base (grain long)

75 to 135 g/m2 (20 to 36 lb bond)

75 to 135 g/m2 (20 to 36 lb bond)

Envelopes2 Sulfite, wood- free or up to 100% cotton bonds

60 to 105 g/m2 (16 to 28 lb bond)3

1 Grain short is preferred for papers over 135 g/m2. 2 100% cotton content maximum weight—24 lb. 3 28 lb bond envelopes are limited to 25% cotton content.

Show 7 more labels / short text on this page
Print media weight · 500-sheet trays · Multipurpose · Duplex unit · feeder · Print media Type · Supported print media
Page 41 of the Lexmark 840 user manual — Media weights supported in the finisher
Page 41 · click to enlarge
Page 41

Understanding paper and specialty media guidelines

Media weights supported in the finisher

Offset Staple Hole Punch

Paper Xerographic or business paper

64 to 105 g/m2 grain long (17 to 28 lb bond)

64 to 216 g/m2 grain long (17 to 58 lb bond)

  • 40 sheets of 90 g/m 2 grain long (24 lb bond)
  • 50 sheets of 64 to 75 g/m 2 grain long (17 to 20 lb bond)

64 to 216 g/m2 grain long (17 to 58 lb bond)

Card stock— maximum (grain long)

Index Bristol 163 g/m2 (90 lb bond) Not recommended

Tag 163 g/m2 (100 lb bond)

Cover 176 g/m2 (65 lb bond)

Card stock— maximum (grain short)

Index Bristol 199 g/m2 (110 lb bond) Not recommended

Tag 203 g/m2 (125 lb bond)

Cover 216 g/m2 (80 lb bond)

Transparencies Laser printer 138 to 146 g/m2 37 to 39 lb bond) Not recommended

140 to 175 g/m2 (up to 47 lb bond)

Integrated forms Pressure sensitive area

Paper base (grain long)

75 to 135 g/m2 (20 to 36 lb bond)

Labels — upper limit

Paper 180 g/m2 (48 lb bond)

60 to 105 g/m2 (16 to 28 lb bond)

Envelopes Sulfite, wood-free or up to 100% cotton bond

Show 8 more labels / short text on this page
Finisher media weight · Bin 2 · Print media Type · Bin 1 · Not recommended · Not recommended · Not recommended · Supported print media
Page 42 of the Lexmark 840 user manual — Curl
Page 42 · click to enlarge
Page 42

Understanding paper and specialty media guidelines

Selecting print media

Selecting the appropriate print media for the printer helps you avoid printing problems. The following sections contain guidelines for choosing the correct print media for the printer.

  • Paper
  • Transparencies
  • Envelopes
  • Labels
  • Card stock

Paper

To ensure the best print quality and feed reliability, use 90 g/m2 (24 lb) xerographic, grain long paper. Business papers designed for general business use may also provide acceptable print quality.

We recommend Lexmark part number 12A5950 letter size glossy paper and Lexmark part number 12A5951 for A4 size glossy paper.

Always print several samples before buying large quantities of any type of media. When choosing any media, consider the weight, fiber content, and color.

The laser printing process heats paper to high temperatures of 230°C (446°F) for non-MICR applications. Use only paper able to withstand these temperatures without discoloring, bleeding, or releasing hazardous emissions. Check with the manufacturer or vendor to determine whether the paper chosen is acceptable for laser printers.

When loading paper, note the recommended print side on the paper package, and load paper accordingly. For detailed tray loading instructions, see the following:

  • Loading standard or optional 500-sheet trays on page 49
  • Loading the multipurpose feeder on page 52
  • Loading the 2000-sheet dual input trays on page 55
  • Loading the 2000-sheet high capacity feeder on page 56

Paper characteristics

The following paper characteristics affect print quality and reliability. It is recommended that these guidelines are followed when evaluating new paper stock.

For detailed information, see the Card Stock & Label Guide available on the Lexmark Web site at www.lexmark.com/ publications.

Weight

The printer can automatically feed paper weights from 60 to 176 g/m2 (16 to 47 lb bond) grain long in the integrated and optional trays and paper weights from 60 to 135 g/m2 (16 to 36 lb bond) grain long in the multipurpose feeder. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 90 g/m2 (24 lb bond) grain long paper. To use paper narrower than 182 x 257 mm (7.2 x 10.1 in.), it is recommended that the weight be greater than or equal to 90 g/m2 (24 lb bond).

Curl

Curl is the tendency of media to curve at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold and dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.

Selecting print media

Page 43 of the Lexmark 840 user manual — Selecting paper
Page 43 · click to enlarge
Page 43

Understanding paper and specialty media guidelines

Smoothness

The degree of smoothness of paper directly affects print quality. If the paper is too rough, the toner does not fuse to the paper properly, resulting in poor print quality. If the paper is too smooth, it can cause paper feeding or print quality issues. Smoothness needs to be between 100 and 300 Sheffield points; however, smoothness between 150 and 250 Sheffield points produces the best print quality.

Moisture content

The amount of moisture in the paper affects both print quality and the ability of the printer to feed the paper properly. Leave the paper in its original wrapper until it is time to use it. This limits the exposure of the paper to moisture changes that can degrade its performance.

Condition paper while it is still in the original wrapper. To condition it, store it in the same environment as the printer for 24 to 48 hours before printing to let the paper stabilize in the new conditions. Extend the time several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period because of the mass of material.

Grain direction

Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.

For 60 to 90 g/m2 (16 to 24 lb bond) paper, grain long fibers are recommended.

Fiber content

Most high-quality xerographic paper is made from 100% chemically pulped wood. This content provides the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton possess characteristics that can result in degraded paper handling.

Unacceptable paper

The following papers are not recommended for use with the printer:

  • Chemically treated papers used to make copies without carbon paper, also known as carbonless papers, carbonless copy paper (CCP), or no carbon required (NCR) paper
  • Preprinted papers with chemicals that may contaminate the printer
  • Preprinted papers that can be affected by the temperature in the printer fuser
  • Preprinted papers that require a registration (the precise print location on the page) greater than ±0.09 in., such as optical character recognition (OCR) forms

In some cases, you can adjust registration with your software application to successfully print on these forms.

  • Coated papers (erasable bond), synthetic papers, thermal papers
  • Rough-edged, rough or heavily textured surface papers or curled papers
  • Recycled papers containing more than 25% post-consumer waste that do not meet DIN 19 309
  • Recycled paper having a weight less than 60 g/m 2 (16 lb)
  • Multiple-part forms or documents

Selecting paper

Proper paper loading helps prevent jams and ensures trouble-free printing.

To help avoid jams or poor print quality:

  • Always use new, undamaged paper.
  • Before loading paper, know the recommended print side of the paper. This information is usually indicated on the paper package.

Selecting print media

Page 44 of the Lexmark 840 user manual — Printing on letterhead
Page 44 · click to enlarge
Page 44

Understanding paper and specialty media guidelines

  • Do not use paper that has been cut or trimmed by hand.
  • Do not mix media sizes, weights, or types in the same source; mixing results in jams.
  • Do not use coated papers unless they are specifically designed for electrophotographic printing.
  • Do not forget to change the Paper Size setting when using a source that does not support auto size sensing.
  • Do not remove trays while a job is printing or Busy appears on the operator panel.
  • Make sure the Paper Type, Paper Texture, and Paper Weight settings are correct. (See “Paper Menu” in the Menus and Messages Guide located on the publications CD for detailed information about these settings.)
  • Make sure the paper is properly loaded in the source.
  • Flex paper back and forth. Do not fold or crease the paper. Straighten the edges on a level surface.

Selecting preprinted forms and letterhead

Use the following guidelines when selecting preprinted forms and letterhead paper for the printer:

  • Use grain long papers for best results for 60 to 90 g/m 2 weights.
  • Use only forms and letterhead printed using an offset lithographic or engraved printing process.
  • Avoid papers with rough or heavily textured surfaces.

Use papers printed with heat-resistant inks designed for use in xerographic copiers. The ink must withstand temperatures of 230°C (446°F) without melting or releasing hazardous emissions. Use inks that are not affected by the resin in toner. Inks that are oxidation-set or oil-based should meet these requirements; latex inks might not. When in doubt, contact the paper supplier.

Preprinted papers such as letterhead must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions.

Printing on letterhead

Check with the manufacturer or vendor to determine whether the chosen preprinted letterhead is acceptable for laser printers.

Page orientation is important when printing on letterhead. Use the following table for help when loading letterhead in the media sources.

Media source or process Print side Top of page

  • 500-sheet trays
  • Single-sided printing: Printed letterhead face-up
  • Duplex (two-sided) printing: Printed letterhead face-down
  • Long-edge fed: Letterhead top edge towards the front of the tray.
  • Short-edge fed: Letterhead top edge towards the left of the tray.

2000-sheet dual input trays Letterhead goes toward the front of the tray.

  • 2000-sheet high capacity feeder
  • Single-sided printing: Printed letterhead face-down
  • Duplex (two-sided) printing: Printed letterhead face-up

Letterhead goes toward the front of the tray.

  • Multipurpose feeder
  • Long-edge fed: Letterhead top edge towards the front of the printer.
  • Short-edge fed: Letterhead top edge enters last.

Selecting print media

Page 45 of the Lexmark 840 user manual — Envelopes
Page 45 · click to enlarge
Page 45

Understanding paper and specialty media guidelines

Transparencies

Feed transparencies from the standard tray or the multipurpose feeder. Try a sample of any transparencies being considered for use with the printer before buying large quantities.

When printing on transparencies:

  • Be sure to set the Paper Type to Transparency from the printer driver or from MarkVision™ Professional to avoid damaging the printer.
  • Use transparencies designed specifically for laser printers. Transparencies must be able to withstand temperatures of 230°C (446°F) without melting, discoloring, offsetting or releasing hazardous emissions.
  • To prevent print quality problems, avoid getting fingerprints on the transparencies.
  • Before loading transparencies, fan the stack to prevent sheets from sticking together.

Selecting transparencies

The printer can print directly on transparencies designed for use in laser printers. Print quality and durability depend on the transparency used. Always print samples on the transparencies being considered for use before buying large quantities.

We recommend Lexmark part number 70X7240 letter size transparency and Lexmark part number 12A5010 for A4 size transparency.

The Paper Type setting should be set to Transparency to help prevent jams. (See “Paper Type” on the publications CD for detailed information about this setting.) Check with the manufacturer or vendor to determine whether the transparencies are compatible with laser printers that heat transparencies to 230°C (446°F). Use only transparencies that are able to withstand these temperatures without melting, discoloring, offsetting, or releasing hazardous emissions. For detailed information, see the Card Stock & Label Guide, which is available on the Lexmark Web site at www.lexmark.com/publications.

Transparencies can be fed automatically from the multipurpose feeder and the standard 500-sheet trays (Tray 1 and Tray 2). See Print media types on page 39 for information about transparency compatibility with output bins.

Be careful when you handle transparencies. Fingerprints on the surface of the transparency cause poor print quality.

Envelopes

You can load up to 10 envelopes in the multipurpose feeder. Try a sample of any envelopes you are considering using with the printer before buying large quantities. See Loading the multipurpose feeder on page 52 for instructions on loading envelopes.

When printing on envelopes:

  • To achieve the best possible print quality, use only high-quality envelopes that are designed for use in laser printers.
  • Set the Paper Source in the Paper menu based on the source in use, set the Paper Type to Envelope, and select the correct envelope size from the operator panel, the printer driver, or from MarkVision Professional.
  • For best performance, use envelopes made from 90 g/m 2 (24 lb bond) paper. Use up to 105 g/m 2 (28 lb bond) weight for the 500-sheet standard trays and multipurpose feeder as long as the cotton content is 25% or less. Envelopes with 100% cotton content must not exceed 90 g/m 2 (24 lb bond) weight.
  • Use only new, undamaged envelopes.
  • For best performance and to minimize jams, do not use envelopes that: – Have excessive curl or twist. – Are stuck together or damaged in any way. – Contain windows, holes, perforations, cutouts or embossing. – Use metal clasps, string ties, or metal folding bars. – Have an interlocking design. – Have postage stamps attached. – Have any exposed adhesive when the flap is in the sealed or closed position. – Have nicked edges or bent corners.

Selecting print media

Page 46 of the Lexmark 840 user manual — Labels
Page 46 · click to enlarge
Page 46

Understanding paper and specialty media guidelines

  • – Have rough, cockle, or laid finishes.
  • Use envelopes that can withstand temperatures of 230°C (446°F) without sealing, excessive curling, wrinkling, or releasing hazardous emissions. If you have any doubts about the envelopes you are considering using, check with the envelope supplier.
  • Adjust the width guide to fit the width of the envelopes.
  • Load only one size of envelope at a time.
  • A combination of high humidity (over 60%) and the high printing temperatures may seal the envelopes.

Labels

The printer can print on many labels designed for use with laser printers, except for vinyl labels. These labels are supplied in letter size, A4 size, and legal size sheets. Label adhesives, face sheet (printable stock), and topcoats must be able to withstand temperatures of 230°C (446°F) and pressure of 25 pounds per square inch (psi).

Try a sample of any labels you are considering using with the printer before purchasing a large quantity.

For detailed information on label printing, characteristics, and design, see the Card Stock & Label Guide available on the Lexmark Web site at www.lexmark.com/publications.

After printing approximately 10,000 pages of labels (or each time you replace the toner cartridge), complete the following steps to maintain printer feeding reliability:

1 Print five sheets of paper.

2 Wait approximately five seconds.

3 Print five more sheets of paper.

When printing on labels:

  • Set the Paper Type menu item to Labels in the Paper menu. Set the Paper Type from the printer operator panel, the printer driver, or from MarkVision Professional.
  • Do not load labels together with paper or transparencies in the same source; mixing media can cause feeding problems.
  • Do not use label sheets with a slick backing material.
  • Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets also contaminate the printer and the cartridge with adhesive, and could void the printer and cartridge warranties.
  • Use labels that can withstand temperatures of 230°C (446°F) without sealing, excessive curling, wrinkling, or releasing hazardous emissions.
  • Do not print within 1 mm (0.04 in.) of the edge of the label, of the perforations, or between die-cuts of the label.
  • Do not use label sheets that have adhesive to the edge of the sheet. Zone coating of the adhesive at least 1 mm (0.04 in.) away from edges is recommended. Adhesive material contaminates the printer and could void the warranty.
  • If zone coating of the adhesive is not possible, remove a 3 mm (0.125 in.) strip on the leading and driver edge, and use a non-oozing adhesive.
  • Remove a 3 mm (0.125 in.) strip from the leading edge to prevent labels from peeling inside the printer.
  • Portrait orientation is preferred, especially when printing bar codes.
  • Do not use labels that have exposed adhesive.

For detailed information on label printing, characteristics, and design, see the Card Stock & Label Guide, available on the Lexmark Web site at www.lexmark.com/publications.

Selecting print media

Page 47 of the Lexmark 840 user manual — Avoiding jams
Page 47 · click to enlarge
Page 47

Understanding paper and specialty media guidelines

Card stock

Card stock is single ply, and has a large array of properties, such as the moisture content, thickness, and texture, that can significantly affect print quality. See Supported print media on page 35 for information on the preferred weight and for the grain direction of print media.

Try a sample of any card stock you are considering using with the printer before purchasing a large quantity.

See Print media weights on page 40 for information on the preferred weight of media.

When printing on card stock:

  • Set the Paper Type menu item in the Paper Menu to Card Stock from the operator panel, from the printer driver, or from MarkVision Professional. Set the Paper Weight to CardStock Weight, and select the CardStock Weight as Normal or Heavy for the value. Set this from the operator panel, the printer driver, or from MarkVision Professional. Use Heavy for card stock weighing more than or heavier than 163 g/m 2 (90 lb).
  • Be aware that preprinting, perforation, and creasing can significantly affect the print quality and cause media handling or jamming problems.
  • Avoid using card stock that may release hazardous emissions when heated.
  • Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting introduces semi-liquid and volatile components into the printer.
  • The use of grain long card stock is recommended.

Storing print media

Use the following guidelines to avoid paper feeding problems and uneven print quality.

  • For best results, store media in an environment where the temperature is approximately 21°C (70°F) and the relative humidity is 40%.

Most label manufacturers recommend printing in a temperature range of 18 to 24°C (65 to 75°F) with a relative humidity of 40 to 60%.

  • Store cartons of media on a pallet or shelf, rather than directly on the floor.
  • When storing individual packages of media out of the original carton, make sure they rest on a flat surface so the edges do not buckle or curl.
  • Do not place anything on top of the media packages.
  • Store paper in its original wrapper until you load it into the printer.

Avoiding jams

Use appropriate print media (paper, transparencies, labels, and card stock) to help ensure trouble-free printing. See Supported print media on page 35 for more information.

large quantities.

By selecting the appropriate print media and loading it properly, you can avoid most jams. For detailed tray loading instructions, see the following:

  • Loading standard or optional 500-sheet trays on page 49
  • Loading the multipurpose feeder on page 52
  • Loading the 2000-sheet dual input trays on page 55
  • Loading the 2000-sheet high capacity feeder on page 56

Storing print media

Page 48 of the Lexmark 840 user manual — Understanding paper and specialty media guidelines
Page 48 · click to enlarge
Page 48

Understanding paper and specialty media guidelines

The following hints can help you avoid jams:

  • Use only recommended print media.
  • Do not overload the print media sources. Make sure the stack height does not exceed the maximum height indicated by the stack line on the labels in the sources.
  • Do not load wrinkled, creased, damp, or curled print media.
  • Flex, fan, and straighten print media before you load it. If jams do occur with print media, try feeding one sheet at a time through the multipurpose feeder.
  • Do not use print media that you have cut or trimmed yourself.
  • Do not mix print media sizes, weights, or types in the same print media source.
  • Make sure the recommended print side is loaded in the source according to your simplex or duplex needs.
  • Keep print media stored in an acceptable environment. See Storing print media on page 47 .
  • Do not remove trays during a print job.
  • Push all trays in firmly after loading them.
  • Make sure the guides in the trays are properly positioned for the size of print media you have loaded. Make sure the guides are not placed too tightly against the stack of print media.

Avoiding jams

Page 49 of the Lexmark 840 user manual — Loading standard or optional 500-sheet trays
Page 49 · click to enlarge
Page 49
Lexmark 840 — Printing diagram (page 49)
Fig. 21 · Printing

This chapter covers information about loading print media, linking output bins, sending a job to print, printing confidential jobs, canceling a print job, printing a menu settings page, a font list, and a directory list. For tips on paper jam prevention and print media storage, see Avoiding jams on page 47 or Storing print media on page 47.

Loading standard or optional 500-sheet trays

Your printer has two 500-sheet standard trays. You may have also purchased an optional 2x500-sheet drawer which has two additional 500-sheet trays. Print media is loaded into all the 500-sheet trays the same way.

feeder are different than the steps for loading a 500-sheet tray.

To load print media:

so may cause a jam.

1 Pull out the tray.

Lexmark 840 — Loading standard or optional 500-sheet trays diagram (page 49)
Fig. 22 · Loading standard or optional 500-sheet trays

Printing

Page 50 of the Lexmark 840 user manual — Printing
Page 50 · click to enlarge
Page 50

Printing

2 Squeeze the side guide tab, and slide the guide to outside of the tray.

Lexmark 840 — Printing diagram (page 50)
Fig. 23 · Printing

3 Squeeze the front guide tab and slide the guide to the correct position for the size media you are loading.

4 Flex the sheets back and forth to loosen them, then fan them. Do not fold or crease the print media. Straighten the edges on a level surface.

5 Load print media in the tray with the print side up.

Lexmark 840 — Printing diagram (page 50)
Fig. 24 · Printing

For information about loading Letter or A4 size media in the short-edge feed position, see Loading Letter or A4 size print media in the short-edge feed orientation on page 58.

Loading standard or optional 500-sheet trays

Page 51 of the Lexmark 840 user manual — Printing
Page 51 · click to enlarge
Page 51

Printing

6 Squeeze the side guide tab, and slide the guide until it lightly rests against the edge of the media.

Lexmark 840 — Printing diagram (page 51)
Fig. 25 · Printing

7 Insert the tray.

Lexmark 840 — Printing diagram (page 51)
Fig. 26 · Printing

Loading standard or optional 500-sheet trays

Page 52 of the Lexmark 840 user manual — Printing
Page 52 · click to enlarge
Page 52

Printing

Loading the multipurpose feeder

The multipurpose feeder can hold several sizes and types of print media, such as transparencies, postcards, note cards, and envelopes. It can be used for single-page or manual printing or as an additional tray.

The multipurpose feeder can hold approximately:

  • 100 sheets of 75 g/m 2 (20 lb) paper
  • 10 envelopes
  • 75 transparencies

The multipurpose feeder accepts print media within the following dimensions:

  • Width—89 mm (3.5 in.) to 297 mm (11.7 in.)
  • Length—98 mm (3.9 in.) to 432 mm (17.0 in.)

The icons on the multipurpose feeder show you how to load the multipurpose feeder with paper, how to turn an envelope for printing, and how to load letterhead paper for simplex and duplex printing.

To load print media:

the operator panel indicator light is blinking. Doing so may cause a jam.

1 Lower the multipurpose feeder.

Loading the multipurpose feeder

Page 53 of the Lexmark 840 user manual — Printing
Page 53 · click to enlarge
Page 53

Printing

2 Pull the tray extension out.

force on it.

Lexmark 840 — Printing diagram (page 53)
Fig. 27 · Printing

3 Slide the width guides to the outside of the feeder.

4 Flex the sheets or envelopes back and forth to loosen them, then fan them. Do not fold or crease the print media. Straighten the edges on a level surface.

5 Load the media in the feeder.

Lexmark 840 — Printing diagram (page 53)
Fig. 28 · Printing

Loading the multipurpose feeder

Page 54 of the Lexmark 840 user manual — Printing
Page 54 · click to enlarge
Page 54

Printing

6 Slide the width guides until they lightly rest against the edge of the media.

Lexmark 840 — Printing diagram (page 54)
Fig. 29 · Printing

7 Set the Paper Size and Paper Type for the multipurpose feeder (MP Feeder Size and MP Feeder Type) to the correct value for the print media you loaded.

a Press on the operator panel.

b Press until Paper Menu appears, and then press .

c Press until Paper Size/Type appears, and then press .

d Press until MP Feeder Size/Type appears, and then press .

e Press until the appears next to the media size you loaded, and then press .

f Press until the media type you loaded appears, and then press .

g Press repeatedly to return to the Ready state.

Loading the multipurpose feeder

Page 55 of the Lexmark 840 user manual — Printing
Page 55 · click to enlarge
Page 55

Printing

Loading the 2000-sheet dual input trays

The 2000-sheet dual input drawer includes two trays: an 850-sheet tray and an 1150-sheet tray. Although the trays are different in appearance, they both load the same way.

1 Pull out the tray.

Lexmark 840 — Printing diagram (page 55)
Fig. 30 · Printing

2 Squeeze the front guide tab, and slide the guide to the correct position for the size media you are loading.

Lexmark 840 — Printing diagram (page 55)
Fig. 31 · Printing

Loading the 2000-sheet dual input trays

Page 56 of the Lexmark 840 user manual — Loading the 2000-sheet high capacity feeder
Page 56 · click to enlarge
Page 56

Printing

3 Flex the sheets back and forth to loosen them, then fan them. Do not fold or crease the print media. Straighten the edges on a level surface.

4 Load print media in the tray with the print side up.

Lexmark 840 — Printing diagram (page 56)
Fig. 32 · Printing

5 Insert the tray into the printer.

Loading the 2000-sheet high capacity feeder

The high capacity feeder can hold 2000 sheets of Letter, A4, Executive, and JIS B5 paper (75 g/m2 [20 lb]).

1 Pull out the tray.

Lexmark 840 — Loading the 2000-sheet high capacity feeder diagram (page 56)
Fig. 33 · Loading the 2000-sheet high capacity feeder

Loading the 2000-sheet high capacity feeder

Page 57 of the Lexmark 840 user manual — Printing
Page 57 · click to enlarge
Page 57

Printing

2 If loading print media with a different width or length, adjust the width and length guides.

Lexmark 840 — Printing diagram (page 57)
Fig. 34 · Printing

3 Flex the sheets back and forth to loosen them, then fan them. Do not fold or crease the print media. Straighten the edges on a level surface.

4 Load print media in the tray with the print side down.

Lexmark 840 — Printing diagram (page 57)
Fig. 35 · Printing
  • Place pre-punched paper with the holes toward the left side of the tray.
  • Place letterhead (or the top of the page) toward the front of the tray.

5 Insert the tray into the high capacity feeder.

Loading the 2000-sheet high capacity feeder

Page 58 of the Lexmark 840 user manual — Changing the Custom Type Name
Page 58 · click to enlarge
Page 58

Printing

Loading Letter or A4 size print media in the short-edge feed orientation

In order for the printer to recognize letter or A4 size print media loaded in the short-edge feed orientation, Short-edge Printing must be enabled.

1 Make sure the printer is off.

2 Press and hold the and buttons while you turn the printer on.

3 Release both buttons when Performing Self Test appears on the display.

The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.

4 Press until Short-edge Printing appears, and then press .

Disabled appears on the second line of the display.

5 Press or to change the setting to Enabled, and then press .

Submitting Selection appears briefly on the display, and then is replaced by Config Menu on the first line and Short-edge Printing on the second line.

6 Press and release or until Exit Config Menu appears, and then press .

Activating Menu Changes appears briefly, followed by Performing Self Test. The printer returns to Ready.

Setting up trays with different orientations

We recommend that you use the custom type settings to differentiate print media of the same size with different orientations. For example, if you want to have letter-size paper loaded into both standard trays, but one in the long-edge orientation and one in the short-edge orientation, you could set up the trays as follows:

  • Tray 1 : Long-edge Fed; Paper Size=Letter; Paper Type=Plain
  • Tray 2 : Short-edge Fed; Paper Size=Letter; Paper Type=Custom Type 1

By setting the printer menus like this, you can easily choose which orientation you want to use for a print job by selecting the appropriate tray.

Changing the Custom Type Name

You can use the printer Embedded Web Server or MarkVision to define a name other than "Custom Type [x]" for each of the custom media types that are loaded. When a custom name is defined for a Custom Type, then the printer displays this name wherever it would normally display "Custom Type [x]".

Loading Letter or A4 size print media in the short-edge feed orientation

Page 59 of the Lexmark 840 user manual — Linking trays
Page 59 · click to enlarge
Page 59

Printing

To define a custom name using the Embedded Web Server:

1 Open the printer Embedded Web Server by typing its IP address in the address bar of a browser. For example:

http://192.168.0.11

2 Click Configuration.

3 Click PAPER MENU.

4 Click CUSTOM NAMES.

5 Define one or more custom names.

For example, you could enter names such as “Short-edge Letter” or “Yellow Glossy.”

6 Click Submit.

Linking trays

Tray linking enables the automatic linking feature for trays when you load the same size and type of print media in multiple sources. The printer automatically links the trays; when one tray is empty, print media feeds from the next linked tray.

For example, if you have the same size and type of print media loaded in tray 2 and tray 4, the printer selects print media from tray 2 until it becomes empty, and then the printer automatically feeds print media from the next linked tray—tray 4.

By linking all five trays, you effectively create a single source with a capacity of 4,000 sheets.

If you load the same size print media in each tray, make sure the print media is all the same type in order to link the trays.

To set the paper type or size:

1 Press on the operator panel.

2 Press until Paper Menu appears, and then press .

3 Press until Paper Size/Type appears, and then press .

4 Press until Tray <x> Size/Type appears, and then press .

5 Press until the appears next to the media size you loaded, and then press .

6 Press until the media type you loaded appears, and then press .

7 Press repeatedly to return to the Ready state.

Once the trays you selected are loaded with the same size and type of print media, select the same Paper Type setting in the Paper menu for these sources.

To disable tray linking, set the Paper Type to a unique value in each one of the trays. If all the trays do not have the same type of print media when they are linked, you could mistakenly print a job on the wrong paper type.

Linking trays

Page 60 of the Lexmark 840 user manual — Linking output bins
Page 60 · click to enlarge
Page 60

Printing

Identifying and linking output bins

There is one standard output bin on all printer models. If you need additional output capacity, the optional finisher provides up to 3500 sheets of additional output capacity.

The following table provides information on output bin capacities.

Lexmark 840 — Printing diagram (page 60)
Fig. 36 · Printing

Output bin Each bin accommodates Illustration of output bin

  • Standard bin
  • 500 sheets * (75 g/m 2 [20 lb]) plain paper
  • 300 transparencies
  • 200 labels
  • 50 envelopes (75 g/m 2 [20 lb])

Finisher bin 1 500 sheets (75 g/m2 [20 lb]) plain paper

Finisher bin 2 3000 sheets† (75 g/m2 [20 lb]) plain paper

* Standard bin capacity with finisher installed: up to 300 sheets. † This capacity may decrease if mixed print media sizes are sent to this bin.

Linking output bins

If you have multiple output bins, linking them lets you create a single output source so the printer can automatically switch output to the next available bin. For more information on the values available to configure your output bins, see the Menus and Messages Guide.

to the floor to the bin farthest from the floor.

To link output bins:

1 Press on the operator panel.

2 Press until Paper Menu appears, and then press .

Identifying and linking output bins

Page 61 of the Lexmark 840 user manual — Sending a job to print
Page 61 · click to enlarge
Page 61

Printing

3 Press until Bin Setup appears, and then press .

4 Press until Configure Bins appears, and then press .

5 Press until Link appears, and then press .

6 Press repeatedly to return to the Ready state.

Sending a job to print

A printer driver is software that lets your computer communicate with your printer. When you choose Print from a software application, a window representing the printer driver opens. You can then select the appropriate settings for the specific job you are sending to the printer. Print settings selected from the driver override the default settings selected from the printer operator panel.

You may need to click Properties or Setup from the initial Print box to see all of the available printer settings you can change. If you are not familiar with a feature in the printer driver window, open the online Help for more information.

To support all the printer features, use the Lexmark custom printer drivers supplied with your printer. Updated drivers, as well as a complete description of the driver packages and Lexmark driver support, are available from the Lexmark Web site. You can also use the system drivers built into your operating system.

To print a job from a typical Windows application:

1 Open the file you want to print.

2 From the “File” menu, select Print.

3 Select the correct printer in the dialog. Modify the printer settings as appropriate (such as the pages you want to print or the number of copies).

4 Click Properties or Setup to adjust printer settings that were not available on the first screen, and then click OK.

5 Click OK or Print to send the job to the selected printer.

Sending a job to print

Page 62 of the Lexmark 840 user manual — Printing
Page 62 · click to enlarge
Page 62

Printing

Printing from a USB flash memory device

A USB Direct interface is located on the operator panel so you can insert a USB flash memory device and print PDF documents. Printing a document from a USB flash memory device is similar to printing a held job.

For information regarding tested and approved USB flash memory devices, see our Lexmark Web site at http:// support.lexmark.com and click on KnowledgeBase to search for Direct USB printing.

  • USB devices must be compatible with the USB 2.0 standard.
  • Hi-Speed USB devices must support the Full-Speed standard as well. Devices only supporting USB low speed capabilities are not supported.
  • USB devices must use the FAT file system. Devices formatted with NTFS or any other file system are not supported.
  • You cannot print encrypted files or files without printing permissions.

To print from a USB flash memory device:

1 Make sure the printer is on and Ready or Busy appears.

2 Insert a USB flash memory device into the USB Direct interface.

  • If you insert the memory device when the printer requires attention such as when a paper jam has occurred, the printer ignores the memory device.
  • If you insert the memory device when the printer is busy printing other jobs, the message Printer Busy appears. Select Continue , and your job prints after the other jobs finish.

Printing from a USB flash memory device

Page 63 of the Lexmark 840 user manual — Canceling a job from a computer running Windows
Page 63 · click to enlarge
Page 63

Printing

3 Press until the appears next to the document you want to print, and then press .

A screen asking the number of copies to be printed will appear.

USB drive

Copies

My_document_01

My_document_02

4 To print only one copy, press , or manually input the number of copies with the number pad, then press .

finished printing.

The document will begin printing.

If you leave the device in the printer after exiting the USB drive menu, you can still print PDFs on the device as held jobs. See Printing confidential and held jobs on page 65.

Canceling a print job

There are several methods for canceling a print job.

  • Canceling a job from the printer operator panel
  • Canceling a job from a computer running Windows

– Canceling a job from the taskbar – Canceling a job from the desktop

  • Canceling a job from a Macintosh computer

– Canceling a job from a Macintosh computer running Mac OS 9.x – Canceling a job from a Macintosh computer running Mac OS X

Canceling a job from the printer operator panel

page 9.

If the job you want to cancel is printing, and Busy appears on the display, press until Cancel a job appears, and then press . The message Canceling Job appears until the job is canceled.

Canceling a job from a computer running Windows

Canceling a job from the taskbar

When you send a job to print, a small printer icon appears in the right corner of the taskbar.

1 Double-click the printer icon.

A list of print jobs appears in the printer window.

2 Select the job you want to cancel.

Canceling a print job

Page 64 of the Lexmark 840 user manual — Printing the menu settings page
Page 64 · click to enlarge
Page 64

Printing

3 Press the Delete key on the keyboard.

Canceling a job from the desktop

1 Minimize all programs to reveal the desktop.

2 Double-click the My Computer icon.

3 Double-click the Printers icon.

A list of available printers appears.

4 Double-click the printer you selected when you sent the job.

A list of print jobs appears in the printer window.

5 Select the job you want to cancel.

6 Press the Delete key on the keyboard.

Canceling a job from a Macintosh computer

Canceling a job from a Macintosh computer running Mac OS 9.x

When you send a job to print, the printer icon for your selected printer appears on the desktop.

1 Double-click the printer icon on your desktop.

A list of print jobs appears in the printer window.

2 Select the print job you want to cancel.

3 Click the trash can icon.

Canceling a job from a Macintosh computer running Mac OS X

1 Open Applications Æ Utilities, and then double-click Print Center or Printer Setup.

2 Double-click the printer you are printing to.

3 In the printer window, select the print job you want to cancel.

4 Press Delete.

Printing the menu settings page

You can print a menu settings page to review the default printer settings and to verify printer options are installed correctly.

1 Make sure the printer is on and Ready.

2 Press on the operator panel.

3 Press until Reports appears, and then press .

4 Press until Menu Settings Page appears, and then press .

Printing Menus Settings appears on the display.

The printer returns to the Ready state after the menu settings page prints.

Printing the menu settings page

Page 65 of the Lexmark 840 user manual — Printing a confidential job
Page 65 · click to enlarge
Page 65

Printing

Printing a network setup page

You can print a network settings page to review the default printer settings and to verify printer options are installed correctly. Go to Printing a network setup page on page 17.

Printing a font sample list

To print samples of the fonts currently available for your printer:

1 Make sure the printer is on and the Ready message appears.

2 Press on the operator panel.

3 Press until Reports appears, and then press .

4 Press until Print Fonts appears, and then press .

5 Press until the appears next to PCL Emul Fonts, PostScript Fonts, or PPDS Fonts, and then press .

Printing a directory list

A directory listing shows the resources stored in flash memory or on the hard disk. To print a listing:

1 Make sure the printer is on and the Ready message appears.

2 Press on the operator panel.

3 Press until Reports appears, and then press .

4 Press until Print Directory appears, and then press .

The message Printing Directory List appears on the display.

The printer returns to the Ready state after the directory list prints.

Printing confidential and held jobs

The term held job refers to any type of print job that can be initiated by the user at the printer. This includes a confidential job, a verify print job, a reserve print job, a repeat print job, a bookmark, a profile, or a file on a USB flash memory device.

When sending a job to the printer, you can specify in the driver that you want the printer to hold the job in memory. Once your job is stored in printer memory, go to the printer and use the printer operator panel to specify what you want to do with your print job.

All confidential and held jobs have a user name associated with them. To access confidential or held jobs, you must first select the type of job (confidential or held), and then select your user name from the user name list. Once you select your user name, you can print all your confidential jobs or select an individual print job. You can then choose the number of copies for the print job or you can delete the print job.

Printing a confidential job

When you send a confidential job to the printer, you must enter a personal identification number (PIN) from the driver. The PIN must be four digits using the numbers 0–9. The job is held in printer memory until you enter the same four-digit PIN from the operator panel and choose to print or delete the job. This ensures the job does not print until you are there to retrieve it. No one else using the printer can print the job without the PIN.

Printing a network setup page

Page 66 of the Lexmark 840 user manual — At the printer
Page 66 · click to enlarge
Page 66

Printing

Windows

1 From a word processor, spreadsheet, browser, or other application, select File Æ Print.

2 Click Properties. (If there is no Properties button, click Setup, and then click Properties.)

3 Depending on the operating system, you may have to click the Other Options tab, and then click Print and Hold.

Confidential Print or Print and Hold, and then follow the driver instructions.

4 Enter a User Name and PIN.

5 Send your job to the printer.

Go to the printer when you are ready to retrieve your confidential print job, and follow the At the printer steps on page 66.

Macintosh

1 From a word processor, spreadsheet, browser, or other application, select File Æ Print.

2 In the “Copies & Pages” or “General” pop-up menu, select Job Routing.

a When using Mac OS 9, if Job Routing is not a choice on the pop-up menu, select Plug-in Preferences Æ Print Time Filters.

b Turn down the disclosure triangle to the left of Print Time Filters, and select Job Routing.

c In the pop-up menu, select Job Routing.

3 In the radio group, select Confidential Print.

4 Enter a User Name and PIN.

5 Send your job to the printer.

Go to the printer when you are ready to retrieve your confidential print job, and follow the At the printer steps on page 66.

At the printer

1 Press until Held jobs appears, and then press .

2 Press until Confidential jobs appears, and then press .

3 Press until the appears next to your user name, and then press .

4 Enter your PIN.

For more information, see Entering a personal identification number (PIN) on page 67.

5 Press until the appears next to the job you want to print, and then press .

Printing confidential and held jobs

Page 67 of the Lexmark 840 user manual — Windows
Page 67 · click to enlarge
Page 67

Printing

Entering a personal identification number (PIN)

When you select Confidential Job from the Held job menu, the following prompt appears on the display after you select your user name:

Enter PIN

*

1 Use the numeric pad to enter the four-digit PIN associated with your confidential job.

If you enter an invalid PIN, the Invalid PIN screen appears.

  • To reenter the PIN, make sure Try again appears, and then press .
  • To cancel, press until Cancel appears, and then press .

2 Press until the appears next to the job you want to print, and then press .

Printing and deleting held jobs

Held jobs such as Verify Print, Reserve Print, Repeat Print, Bookmarks, and USB flash memory files differ in function and do not require a PIN to print the job. These jobs are printed or deleted from the printer operator panel.

Verify Print

If you send a Verify Print job, the printer prints one copy and holds the remaining copies you requested in printer memory. Use Verify Print to examine the first copy to see if it is satisfactory before printing the remaining copies. Once all copies are printed, the Verify Print job is automatically deleted from printer memory.

Reserve Print

If you send a Reserve Print job, the printer does not print the job immediately. It stores the job in memory so you can print the job later. The job is held in memory until you delete it from the Held Jobs menu. Reserve Print jobs may be deleted if the printer requires extra memory to process additional held jobs.

Repeat Print

If you send a Repeat Print job, the printer prints all requested copies of the job and stores the job in memory so you can print additional copies later. You can print additional copies as long as the job remains stored in memory.

memory to process additional held jobs.

Windows

1 From a word processor, spreadsheet, browser, or other application, select File Æ Print.

2 Click Properties. (If there is no Properties button, click Setup, and then click Properties.)

Printing confidential and held jobs

Page 68 of the Lexmark 840 user manual — At the printer
Page 68 · click to enlarge
Page 68

Printing

3 Depending on the operating system, you may have to click the Other Options tab, and then click Print and Hold.

Print and Hold, then follow the driver instructions.

4 Select the type of held job you want, and then send your job to the printer.

Go to the printer when you are ready to retrieve your confidential print job, and follow the At the printer steps on page 68.

Macintosh

1 From a word processor, spreadsheet, browser, or other application, select File Æ Print.

2 In the Copies & Pages or General pop-up menu, select Job Routing.

a When using Mac OS 9, if Job Routing is not a choice on the pop-up menu, select Plug-in Preferences Æ Print Time Filters.

b Turn down the disclosure triangle to the left of Print Time Filters, and select Job Routing.

c In the pop-up menu, select Job Routing.

3 In the radio group, select the type of held job you want, enter a user name, and then send your job to the printer.

Go to the printer when you are ready to retrieve your confidential print job, and follow the At the printer steps on page 68.

At the printer

1 Press until Held jobs appears, and then press .

2 Press until the appears next to your user name, and then press .

3 Press until the appears next to the type of action you want to perform:

Print All Jobs Delete All Jobs

Print A Job Delete A Job

4 Press .

5 Press until the appears next to the job you want, and then press .

The job will print or be deleted according to the type of print job and action you selected.

Printing confidential and held jobs

Print Copies

Page 69 of the Lexmark 840 user manual — Printing
Page 69 · click to enlarge
Page 69

Printing

Printing A5/Statement or JIS-B5/Executive sizes

When Auto Size Sensing is set to On, the printer cannot distinguish between Statement and A5 or Executive and JIS-B5. Follow these directions to change the Size Sensing setting.

1 Make sure the printer is off.

2 Press and hold the and buttons while you turn the printer on.

3 Release both buttons when Performing Self Test appears on the display.

The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.

4 Press until Size Sensing appears, and then press .

Tray 1 Sensing appears on the second line of the display.

5 Press and release or to select the input option that has A5/Statement or JIS-B5/Executive loaded, and then press .

The first line of the display shows the selected input option, and the second line shows the current setting.

6 Press or to change the setting to Sense A5/Sense Statement or Sense JIS-B5/Sense Executive, and then press .

Submitting Selection appears briefly on the display, and then is replaced by Config Menu on the first line and Size Sensing on the second line.

7 Press and release or until Exit Config Menu appears, and then press .

Activating Menu Changes appears briefly, followed by Performing Self Test. The printer returns to Ready.

Printing A5/Statement or JIS-B5/Executive sizes

Page 70 of the Lexmark 840 user manual — Status / Supplies
Page 70 · click to enlarge
Page 70

7 Maintaining the printer

Periodically, you need to complete certain tasks to maintain optimum print quality. These tasks are covered in this chapter.

If several people are using the printer, you may want to designate a key operator to do the setup and maintenance of your printer. Refer printing problems and maintenance tasks to this key operator.

In the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark Authorized Supplies Dealers in your area. In other countries or regions, visit the Lexmark Web site at www.lexmark.com or contact the place where you bought your printer.

Storing supplies

Choose a cool, clean storage area for your printer supplies. Store supplies right side up in their original packaging until you are ready to use them.

Do not expose supplies to:

  • Direct sunlight
  • Temperatures above 35°C (95°F)
  • High humidity (above 80%)
  • Salty air
  • Corrosive gases
  • Heavy dust

Determining the status of supplies

The printer operator panel alerts you once a supply item or maintenance is required. You can also view the status of supplies in your printer on the operator panel unless the printer is printing or in a busy state. The header or gray area at the top of the display will indicate the printer is Ready and lets you know if any trays are low. Selecting Status / Supplies on the display will open the Status / Supplies screen where you can view the status of the various trays and open the supplies screen to view the current status of your toner cartridge.

Ready. Tray 1 Low, Tray 2 Low… Status / Supplies

Status / Supplies

View supplies

Held jobs

Ready

Tray 1 Low

View Supplies

Toner Low

Staples OK

Maintaining the printer

Page 71 of the Lexmark 840 user manual — Ordering a photoconductor kit
Page 71 · click to enlarge
Page 71

Maintaining the printer

Photoconductor kit end-of-life

To ensure print quality and to avoid damage to the printer, the printer stops operating after the photoconductor kit has reached approximately 60,000 pages (Letter/A4). The message 84 Replace PC Unit is displayed when the printer reaches this point. If the Toner Alarm setting is set to Single or Continuous (default is Off), the printer automatically notifies you before the photoconductor reaches this point and displays the message 84 PC Unit Life Warning. To avoid having the printer stop operating, replace the photoconductor kit when you first receive the 84 PC Unit Life Warning message. Once the photoconductor kit has been replaced, normal printer operation resumes.

Conserving supplies

Several settings in your application software or on the display let you conserve toner and paper. For more information on changing these settings, see the Menus and Messages Guide.

Supply Menu selection item What the setting does

Toner Toner Darkness in the Defaults Æ Quality Menu

Lets you adjust the level of toner released on a sheet of print media. The values range from 1 (lightest setting) to 10 (darkest setting).

Print media Multipage Print in the Defaults Æ Finishing Menu

Causes the printer to print the two or more page images on one side of a sheet. Values for Multipage Print are 2 Up, 3 Up, 4 Up, 6 Up, 9 Up, 12 Up, and 16 Up. Combined with the duplex setting, Multipage Print lets you print up to 32 pages on one sheet of paper (16 images on the front and 16 on the back).

Duplex in the Defaults Æ Finishing Menu

Duplex printing is available when you attach the optional duplex unit. It lets you print on both sides of a sheet of paper.

Use your software application or printer driver to send a Verify Print job.

Lets you examine the first copy of a multiple-copy job to be sure it is satisfactory before you print the other copies. If the job is unsatisfactory, you can cancel the job. See Printing and deleting held jobs on page 67 for more information about a Verify Print job.

Ordering supplies

To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark Authorized Supplies Dealers in your area. In other countries or regions, visit the Lexmark Web site at www.lexmark.com or contact the place where you bought your printer.

Ordering a toner cartridge

When the 88 Toner Low message appears, you should order a new toner cartridge. You can print a few hundred pages after the 88 Toner Low message appears. You need to have a new cartridge available when the current one no longer prints satisfactorily.

Order Lexmark part number W84020H.

Ordering a photoconductor kit

When the 84 PC Life Warning message appears, you should order a new photoconductor kit. You can print a few hundred pages after the 84 PC Life Warning message appears.

Order Lexmark part number W84030H.

Photoconductor kit end-of-life

Page 72 of the Lexmark 840 user manual — Recycling Lexmark products
Page 72 · click to enlarge
Page 72

Maintaining the printer

Maintenance kit

80 Scheduled Maintenance appears on the display after 300,000 pages have printed to let you know it is time to replace printer maintenance items. Order a maintenance kit when 80 Scheduled Maintenance first appears on the display. The maintenance kit contains all the items necessary to replace the pick rollers, the fuser, and the transfer roller.

See the following table for the maintenance kit part number for your specific printer.

Machine voltage Part numbers

110 V 40X0956

220 V 40X0957

100 V 40X0958

Ordering staple cartridges

Staple cartridges hold 3,000 staples. Use part number 25A0013 to order a pack of three staple cartridges.

When Staples Low or Staples Empty appears on the operator panel display, insert a new staple cartridge in the finisher. See the illustrations inside the stapler access door for more information.

  • If Staple Alarm is set to Single, the printer stops printing and the Load Staples message appears. Install a new staple cartridge, or press Go to clear the message and continue printing.
  • If Staple Alarm is set to Continuous, the printer displays the Load Staples message and continues printing. A partial sheet of staples will remain in the staple cartridge holder when this message appears. Do not remove this sheet. Install a new staple cartridge to properly feed the partial sheet of staples.

Recycling Lexmark products

To return Lexmark products to Lexmark for recycling:

1 Visit our Web site:

www.lexmark.com/recycle

2 Follow the instructions on the computer screen.

Recycling Lexmark products

Page 73 of the Lexmark 840 user manual — Show A
Page 73 · click to enlarge
Page 73

8 Clearing jams

By carefully selecting print media and loading it properly, you should be able to avoid most paper jams. For more information on avoiding paper jams, see Avoiding jams on page 47. If jams do occur, follow the steps outlined in this section.

To resolve the paper jam messages, you must clear the entire paper path and then press to clear the message and resume printing. The printer prints a new copy of the page that jammed if Jam Recovery is set to On or Auto; however, the Auto setting does not guarantee the page will print.

Identifying jams

When the printer jams, the appropriate jam message appears on the printer operator panel. If you select Show Areas on the operator panel, you can view one or more images to help you clear the jam.

23<x> Paper Jam, 3 pages jammed

Show areas

Show A

Continue

Show C

Show areas A, C, F

Show F

1. Open manual feed door.

Clearing jams

Page 74 of the Lexmark 840 user manual — H
Page 74 · click to enlarge
Page 74

Clearing jams

Access doors and trays

The following illustrations show the areas where jams may occur.

Lexmark 840 — Clearing jams diagram (page 74)
Fig. 37 · Clearing jams
Lexmark 840 — Clearing jams diagram (page 74)
Fig. 38 · Clearing jams

H

G

J

Access doors and trays

Trays 1–4

Page 75 of the Lexmark 840 user manual — 250 Paper Jam Check MP Feeder
Page 75 · click to enlarge
Page 75

Clearing jams

Understanding jam messages

The following table lists the jam messages that can occur and the action necessary to clear the message. The jam message indicates the area where the jam occurred. However, it is best to clear the entire paper path to ensure you have cleared all possible jams.

Message What to do

200, 201, and 202 Paper Jam Check Door A Open the side door, and remove the jam.

203 Paper Jam Check <Areas A/E> Open the side door and the Exit 2 door, and remove the jam.

230 Paper Jam Check Door <A, E, D> Lower the duplex unit, and remove the jam. Open the side door and the Exit 2 door, and remove the jam.

231 Paper Jam Check <A, D> Lower the duplex unit, and remove the jam. Open the side door, and remove the jam.

24x Paper Jam Check Tray <x> Open each tray, and remove any jammed media.

250 Paper Jam Check MP Feeder Remove all media from the multipurpose feeder, flex and stack the media, reload the multipurpose feeder, and adjust the guide.

28x Paper Jam Check Finisher Open the finisher door, bridge unit assembly, or output bin, then remove the jam.

Clearing printer jams

Although there are several places a jam can occur, clearing the paper path is fairly easy depending on the jam message or messages displayed on the operator panel.

to help you quickly clear the print path.

250 Paper Jam Check MP Feeder

1 Remove the paper from the multipurpose feeder.

2 Flex, fan, and restack the media, and place it into the multipurpose feeder.

3 Load the print media.

4 Slide the side guide toward the inside of the tray until it lightly rests against the edge of the media.

5 Press .

Understanding jam messages

Page 76 of the Lexmark 840 user manual — Clearing jams
Page 76 · click to enlarge
Page 76

Clearing jams

24x Paper Jam Check Tray <x>

Paper jams in these areas can occur on the incline surface of a tray or across more than one tray. To clear these areas:

1 Open the tray. If necessary, remove the tray from the printer.

Lexmark 840 — Clearing jams diagram (page 76)
Fig. 39 · Clearing jams

2 Remove the media from the printer tray slot.

Lexmark 840 — Clearing jams diagram (page 76)
Fig. 40 · Clearing jams

3 Remove any crumpled paper from the tray.

4 Insert the tray into the printer.

5 Press .

Clearing printer jams

Page 77 of the Lexmark 840 user manual — Clearing jams
Page 77 · click to enlarge
Page 77

Clearing jams

Clearing the 2000-sheet high capacity feeder (Tray 5)

1 If necessary, close the multipurpose feeder.

2 Slide the high capacity feeder away from the printer.

Lexmark 840 — Clearing jams diagram (page 77)
Fig. 41 · Clearing jams

3 Raise the top door, and lift the jam access cover.

Lexmark 840 — Clearing jams diagram (page 77)
Fig. 42 · Clearing jams
Lexmark 840 — Clearing jams diagram (page 77)
Fig. 43 · Clearing jams

Clearing printer jams

Page 78 of the Lexmark 840 user manual — Clearing jams
Page 78 · click to enlarge
Page 78

Clearing jams

4 Remove the jammed paper.

Lexmark 840 — Clearing jams diagram (page 78)
Fig. 44 · Clearing jams

5 Close the jam access cover and top door.

Lexmark 840 — Clearing jams diagram (page 78)
Fig. 45 · Clearing jams
Lexmark 840 — Clearing jams diagram (page 78)
Fig. 46 · Clearing jams

Clearing printer jams

Page 79 of the Lexmark 840 user manual — 200, 201, and 202 Paper Jam Check Door A
Page 79 · click to enlarge
Page 79

Clearing jams

6 Slide the feeder firmly against the printer.

Lexmark 840 — Clearing jams diagram (page 79)
Fig. 47 · Clearing jams

7 Press .

200, 201, and 202 Paper Jam Check Door A

1 Open Door A by pushing the release latch and lowering the door.

Lexmark 840 — 200, 201, and 202 Paper Jam Check Door A diagram (page 79)
Fig. 48 · 200, 201, and 202 Paper Jam Check Door A

Clearing printer jams

Page 80 of the Lexmark 840 user manual — 203 Paper Jam Check <Areas A/E>
Page 80 · click to enlarge
Page 80

Clearing jams

2 Pull the print media up and toward you.

green lever to make it easier to remove the media. Make sure all paper fragments are removed.

Lexmark 840 — Clearing jams diagram (page 80)
Fig. 49 · Clearing jams

3 Close Door A.

4 Press .

203 Paper Jam Check <Areas A/E>

1 Open Door A by pushing the release latch and lowering the door.

Lexmark 840 — 203 Paper Jam Check <Areas A/E> diagram (page 80)
Fig. 50 · 203 Paper Jam Check <Areas A/E>

Clearing printer jams

Page 81 of the Lexmark 840 user manual — Clearing jams
Page 81 · click to enlarge
Page 81

Clearing jams

2 Open Door E by pushing the release latch and lowering the door.

3 Pull the print media up.

4 Close Door E.

5 Close Door A.

6 Press .

Clearing printer jams

Page 82 of the Lexmark 840 user manual — Clearing jams
Page 82 · click to enlarge
Page 82

Clearing jams

230 Paper Jam Check Door <A, E, D>

1 Open Door D by the duplex rear door.

Lexmark 840 — Clearing jams diagram (page 82)
Fig. 51 · Clearing jams

2 Remove the jammed media.

Lexmark 840 — Clearing jams diagram (page 82)
Fig. 52 · Clearing jams

3 Close Door D.

4 Open Door A by pushing the release latch and lowering the door.

Lexmark 840 — Clearing jams diagram (page 82)
Fig. 53 · Clearing jams

Clearing printer jams

Page 83 of the Lexmark 840 user manual — Clearing jams
Page 83 · click to enlarge
Page 83

Clearing jams

5 Open Door E by pushing the release latch and lowering the door.

6 Pull the print media up.

7 Close Door E.

8 Close Door A.

9 Press .

Clearing printer jams

Page 84 of the Lexmark 840 user manual — Clearing jams
Page 84 · click to enlarge
Page 84

Clearing jams

231 Paper Jam Check <A, D>

1 Open Door D by the duplex rear door.

Lexmark 840 — Clearing jams diagram (page 84)
Fig. 54 · Clearing jams

2 Remove the jammed media.

Lexmark 840 — Clearing jams diagram (page 84)
Fig. 55 · Clearing jams

3 Close Door D.

4 Open Door A by pushing the release latch and lowering the door.

Lexmark 840 — Clearing jams diagram (page 84)
Fig. 56 · Clearing jams

Clearing printer jams

Page 85 of the Lexmark 840 user manual — Clearing Area B
Page 85 · click to enlarge
Page 85

Clearing jams

5 Pull the print media up.

it easier to remove the media. Make sure all paper fragments are removed.

Lexmark 840 — Clearing jams diagram (page 85)
Fig. 57 · Clearing jams

6 Close Door A.

7 Press .

Clearing Area B

1 If the printer is configured with a 2000-sheet high capacity feeder, slide the feeder away from the printer.

Lexmark 840 — Clearing Area B diagram (page 85)
Fig. 58 · Clearing Area B

Clearing printer jams

Page 86 of the Lexmark 840 user manual — Clearing jams
Page 86 · click to enlarge
Page 86

Clearing jams

2 Open Door B.

3 Remove the jammed media.

4 Close Door B.

Clearing printer jams

Page 87 of the Lexmark 840 user manual — Clearing jams
Page 87 · click to enlarge
Page 87

Clearing jams

5 Slide the feeder firmly against the printer.

Lexmark 840 — Clearing jams diagram (page 87)
Fig. 59 · Clearing jams

6 Press .

Clearing printer jams

Page 88 of the Lexmark 840 user manual — Clearing jams
Page 88 · click to enlarge
Page 88

Clearing jams

Clearing Area C

1 If the printer is configured with a 2000-sheet high capacity feeder, slide the feeder away from the printer.

Lexmark 840 — Clearing jams diagram (page 88)
Fig. 60 · Clearing jams

2 Open Door C.

Lexmark 840 — Clearing jams diagram (page 88)
Fig. 61 · Clearing jams

Clearing printer jams

Page 89 of the Lexmark 840 user manual — Clearing jams
Page 89 · click to enlarge
Page 89

Clearing jams

3 Remove the jammed media.

Lexmark 840 — Clearing jams diagram (page 89)
Fig. 62 · Clearing jams

4 Close Door C.

5 Slide the feeder firmly against the printer.

Lexmark 840 — Clearing jams diagram (page 89)
Fig. 63 · Clearing jams

6 Press .

Clearing printer jams

Page 90 of the Lexmark 840 user manual — Clearing Area F
Page 90 · click to enlarge
Page 90

Clearing jams

28x Paper Jam Check Finisher

There are three areas associated with the finisher. Follow the appropriate instructions to clear a jam in the finisher.

Clearing Area F

1 Lift the bridge unit assembly door.

2 Remove the jammed media.

Lexmark 840 — Clearing Area F diagram (page 90)
Fig. 64 · Clearing Area F
Lexmark 840 — Clearing Area F diagram (page 90)
Fig. 65 · Clearing Area F

3 Close the door.

4 Press .

Clearing printer jams

Page 91 of the Lexmark 840 user manual — Clearing Area H
Page 91 · click to enlarge
Page 91

Clearing jams

Clearing Area G

1 Open the finisher door.

Lexmark 840 — Clearing jams diagram (page 91)
Fig. 66 · Clearing jams

2 Remove the jammed media, as indicated on the operator panel.

3 Close the door.

4 Press .

Clearing Area H

1 Lift Door H.

Lexmark 840 — Clearing Area H diagram (page 91)
Fig. 67 · Clearing Area H

2 Remove the jammed media.

Lexmark 840 — Clearing Area H diagram (page 91)
Fig. 68 · Clearing Area H

3 Close the door.

4 Press .

Clearing printer jams

Page 92 of the Lexmark 840 user manual — Clearing jams
Page 92 · click to enlarge
Page 92

Clearing jams

Clearing staple jams

A Staples Empty or Misfed message indicates staples are jammed in the stapler. This requires removing the staple cartridge holder from the printer.

1 Check that the machine stops operations, and open Door G (front door) of the finisher.

2 Hold the lever on the staple cartridge holder, and move the holder to the right (towards you).

Lexmark 840 — Clearing jams diagram (page 92)
Fig. 69 · Clearing jams

3 Firmly pull the colored tab to remove the staple cartridge.

Lexmark 840 — Clearing jams diagram (page 92)
Fig. 70 · Clearing jams

Clearing staple jams

Page 93 of the Lexmark 840 user manual — Clearing jams
Page 93 · click to enlarge
Page 93

Clearing jams

4 Use the metal tab to lift the staple guard, and then pull out the sheet of staples.

Discard the entire sheet.

5 Remove any loose staples from the staple guard.

6 Look through the clear covering on the bottom of the cartridge holder to make sure no staples are jammed in the entry throat.

7 Press down on the staple guard until it snaps securely into place.

Lexmark 840 — Clearing jams diagram (page 93)
Fig. 71 · Clearing jams

8 Push the cartridge holder firmly into the stapler until the holder clicks into place.

Lexmark 840 — Clearing jams diagram (page 93)
Fig. 72 · Clearing jams

9 Close Door G.

Priming Stapler appears on the operator panel display. Priming ensures the stapler is functioning properly.

Clearing staple jams

Page 94 of the Lexmark 840 user manual — Checking an unresponsive printer
Page 94 · click to enlarge
Page 94

9 Troubleshooting

Online customer support

Customer support is available on our Lexmark Web site at www.lexmark.com.

Calling for service

When you call for printer service, describe the problem you are experiencing, the message on the display, and the troubleshooting steps you have already taken to find a solution.

You need to know your printer model type and serial number. See the label on the printer for this information.

The serial number is also listed on the menu settings page. See Printing the menu settings page on page 64 for more information.

For service in the U.S. or Canada, call 1-800-Lexmark (1-800-539-6275). See our Lexmark Web site at www.lexmark.com for the numbers for other countries/regions.

Checking an unresponsive printer

If your printer is not responding, first make sure:

  • The power cord is plugged into the printer and a properly grounded electrical outlet.
  • The electrical outlet is not turned off by any switch or breaker.
  • The printer is not plugged into any surge protectors, uninterrupted power supplies, or extension cords.
  • Other electrical equipment plugged into the outlet is working.
  • The printer is turned on.
  • The printer cable is securely attached to the printer and the host computer, print server, option, or other network device.

Once you have checked each of these possibilities, turn the printer off and back on. This often fixes the problem.

Troubleshooting

Page 95 of the Lexmark 840 user manual — Solving printing problems
Page 95 · click to enlarge
Page 95

Troubleshooting

Printing multiple-language PDFs

Some documents do not print.

The documents contain unavailable fonts.

1 Open the document you want to print in Adobe Acrobat. 2 Click the printer icon. The Print dialog appears. 3 Check the Print as image box. 4 Click OK.

Solving printing problems

The operator panel display is blank or displays only diamonds.

The printer self test failed.

Turn the printer off, wait about 10 seconds, and turn the printer back on. If the Performing Self Test and Ready messages do not appear, turn the printer off and call for service.

The message USB device unsupported appears when using a USB device.

The USB device you are using may not be supported or has an error. Only specific USB flash memory devices are supported.

For information regarding tested and approved USB flash memory devices, see our Lexmark Web site at http:// support.lexmark.com and click on KnowledgeBase to search for Direct USB printing.

Jobs do not print. The printer is not ready to receive data.

Make sure Ready or Power Saver appears on the display before sending a job to print. Press to return the printer to the Ready state.

The specified output bin is full.

Remove the stack of paper from the output bin, and then press

The specified tray is empty.

Load paper in the tray.

You are using the wrong printer driver or are printing to a file.

  • Verify you are using the printer driver associated with your printer.
  • If you are using a USB Direct interface, make sure you are running Windows 98/Me, Windows 2000, Windows XP, or Windows Server 2003 and using a Windows 98/Me, Windows 2000, Windows XP, or Windows Server 2003 compatible printer driver.

Your internal print server is not set up properly or is not connected properly.

Verify that you have properly configured the printer for network printing. See the drivers CD or the Lexmark Web site for information.

You are using the wrong interface cable, or the cable is not securely connected.

Make sure you are using a recommended interface cable. Make sure the connection is secure.

Symptom Cause Solution · Symptom Cause Solution · Printing multiple-language PDFs

Page 96 of the Lexmark 840 user manual — Troubleshooting
Page 96 · click to enlarge
Page 96

Troubleshooting

Held jobs do not print. A formatting error has occurred.

  • Print the job. (Only part of the job may print.)
  • Delete the job.
  • Free up additional printer memory by scrolling through the list of held jobs and deleting others you have sent to the printer. The printer has insufficient memory.

The printer has received invalid data.

Delete the job.

Job takes longer than expected to print.

The job is too complex. Reduce the complexity of your print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.

Page Protect is set to On.

Set Page Protect to Off from the Setup Menu. For more information, see the Menus and Messages Guide.

Job prints from the wrong tray or on the wrong paper or specialty media.

The operator panel menu settings do not match the media loaded in the tray.

Make sure the Paper Size and Paper Type specified in the printer driver match the paper size and type in the tray.

Incorrect characters print.

You are using an incompatible parallel cable.

If you are using a parallel interface, make sure you are using an IEEE 1284-compliant parallel cable. We recommend Lexmark part number 1329605 (10 ft) or 1427498 (20 ft) for the standard parallel port.

The printer is in Hex Trace mode.

If Ready Hex appears on the display, you must exit Hex Trace mode before you can print your job. Turn the printer off and back on to exit Hex Trace mode.

Tray linking does not work.

Tray linking is not configured properly.

  • Make sure both the size and type of media are the same in both trays.
  • Make sure the paper guides in the trays are set for the correct size media.
  • Make sure the menu values for both size and type are set correctly in the Paper menu.
  • See Linking trays on page 59 or see the Menus and Messages Guide for more information.

Large jobs do not collate. Collate is not set to On. Set Collation to On in the Finishing Menu or through the printer driver. Note: Setting Collation to Off in the driver overrides the setting in the Finishing Menu. See the Menus and Messages Guide for more information.

The job is too complex. Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.

The printer does not have enough memory.

Add printer memory or an optional hard disk.

Unexpected page breaks occur.

The job has timed out. Set Print Timeout to a higher value from the Setup Menu. See the Menus and Messages Guide for more information.

Symptom Cause Solution · Solving printing problems

Page 97 of the Lexmark 840 user manual — Troubleshooting
Page 97 · click to enlarge
Page 97

Troubleshooting

Solving option problems

If an option does not operate correctly after it is installed or if it quits working:

  • Turn the printer off, wait for about 10 seconds, and turn the printer on. If this does not fix the problem, unplug the printer, and check the connection between the option and printer.
  • Print the menu settings page, and check to see if the option is listed in the Installed Options list. If the option is not listed, reinstall it. See Printing the menu settings page on page 64 for more information.
  • Make sure the option is selected in the software application you are using.

For Macintosh computer users: Make sure the printer is set up in Chooser.

The following table lists printer options and suggested corrective actions for related problems. If the suggested corrective action does not fix the problem, call your service representative.

  • Drawers
  • Make sure the connection between drawers and the printer is secure.
  • Make sure the print media is loaded correctly.

Duplex unit Make sure the connection between the duplex unit and the printer is secure. If the duplex unit is listed on the menu settings page, but print media jams when it enters or exits the duplex unit, the printer and duplex unit may not be properly aligned.

  • Finisher
  • Make sure the connection between the finisher and the printer is secure. If the finisher is listed on the menu settings page, but print media jams when it exits the printer and enters the finisher, it may not be properly installed. Reinstall the finisher.
  • Make sure you are using a print media size compatible with your optional output bins. See Supported print media on page 35 .

Flash memory Make sure flash memory is securely connected to the printer system board.

Hard disk with adapter

Make sure the hard disk is securely connected to the printer system board.

  • Infrared adapter If infrared communication stops or does not occur, make sure:
  • The distance between the two infrared ports is 1 meter (39 in.) or less. If communication does not occur between ports, move the ports closer together.
  • Both ports are stable.
  • The computer and the printer are on a level surface.
  • The angle of communication between the two infrared ports is within 15 degrees of either side of an imaginary line drawn between the two infrared ports.
  • No bright light, such as direct sunlight, is interfering with communication.
  • No objects are placed between the two infrared ports.
  • Internal print server
  • Make sure the internal print server (also called an internal network adapter or INA) is securely connected to the printer system board.
  • Make sure you are using the correct cable, that it is securely connected, and the network software is correctly set up. See the drivers CD that shipped with your printer for more details.

High capacity feeder (2000-sheet drawer)

See Solving 2000-sheet drawer problems on page 98.

Printer memory Make sure printer memory is securely connected to the printer system board.

  • Make sure the USB/parallel interface card is securely connected to the printer system board.
  • Make sure you are using the correct cable and that it is securely connected.

Option Action · USB/Parallel interface · Solving option problems

Page 98 of the Lexmark 840 user manual — Troubleshooting
Page 98 · click to enlarge
Page 98

Troubleshooting

Solving 2000-sheet drawer problems

The elevator tray does not raise when the loading door is closed, or the elevator tray does not lower when the door is opened and the elevator button is pushed.

  • Check the following:
  • The printer is properly attached to the 2000-sheet drawer.
  • The printer is powered on.
  • The power cord is plugged firmly into the back of the 2000-sheet drawer.
  • The power cord is plugged into an outlet.
  • The outlet has power.

The elevator tray lowers unexpectedly. Check to see if your printer is out of print media or has a jam.

More than one sheet of print media is fed or a sheet is fed improperly.

Remove the print media in the printer paper path, and check the stack to ensure the print media has been loaded properly. Be sure to remove the top and bottom sheets of each ream of paper that is loaded. A jam occurs.

Rubber feed rollers do not turn to advance print media.

  • Check the following:
  • The power cord is plugged firmly into the back of the 2000-sheet drawer.
  • The power cord is plugged into an outlet.
  • The outlet has power.
  • Consistent misfeeds or jams in the drawer. Try the following:
  • Flex the paper.
  • Turn the print media over. Check the following:
  • Drawer is properly installed.
  • Print media is loaded correctly.
  • Print media is not damaged.
  • Print media meets specifications.
  • Guides are positioned correctly for the print media size selected.

Service messages A service message indicates printer failure that may require service. Turn the printer off, wait about 10 seconds, and then turn the printer on. If the error recurs, write down the error number, the problem, and a detailed description. Call for service.

Problem Solution · Solving option problems

Page 99 of the Lexmark 840 user manual — Troubleshooting
Page 99 · click to enlarge
Page 99

Troubleshooting

Solving paper feed problems

Paper frequently jams. You are using paper that does not meet the printer specifications.

Use recommended paper and other specialty media. See the Card Stock & Label Guide available on our Lexmark Web site at www.lexmark.com for detailed specifications. See Avoiding jams on page 47 for information that can help prevent jams from occurring.

You have loaded too much paper or too many envelopes.

Make sure the stack of paper you load does not exceed the maximum stack height indicated in the tray or on the multipurpose feeder.

Guides in the selected tray are not set to the appropriate position for the size paper loaded.

Move the guides in the tray to the correct position.

The paper has absorbed moisture due to high humidity.

Load paper from a fresh package. Store paper in its original wrapper until you load it. See Storing print media on page 47 for more information.

The Paper Jam message remains after you remove the jammed paper.

You have not pressed or have not cleared the entire paper path.

Clear paper from the entire paper path, and then press

See Clearing printer jams on page 75 for more information.

The page that jammed does not reprint after you clear the jam.

Jam Recovery in the Setup menu is set to Off.

Set Jam Recovery to Auto or On. See the Menus and Messages Guide for more information.

Blank pages feed into the output bin.

An incorrect media type is loaded in the tray being printed from.

Load the correct type media for your print job, or change the Paper Type to match the type of media loaded. See the Menus and Messages Guide for more information.

Solving paper feed problems

Symptom Cause Solution

Page 100 of the Lexmark 840 user manual — ABC DEF
Page 100 · click to enlarge
Page 100

Troubleshooting

Solving print quality problems

The information in the following table may help you solve print quality problems. If these suggestions still do not correct the problem, call for service. You may have a printer part that requires adjustment or replacement.

  • Print is too light.
  • The toner may be low.
  • Change the Toner Darkness setting in the Quality menu.
  • Change the Brightness setting in the Quality menu.
  • Change the Contrast setting in the Quality menu.
  • If you are printing on an uneven print surface, change the Paper Weight and Paper Texture settings in the Paper menu.
  • Verify the correct print media is being used.

ABC DEF

Toner smears or print comes off the page.

  • If you are printing on an uneven print surface, change the Paper Weight and Paper Texture settings in the Paper menu.
  • Verify the print media is within the printer specifications. See Understanding paper and specialty media guidelines on page 35 for more details. If the problem continues, contact the Lexmark Customer Support Center at <a href="http://support.lexmark.com" rel="nofollow noopener" target="_blank">http://support.lexmark.com</a> .

ABC DEF

Toner appears on the back of the printed page.

Toner is on the transfer roll. To help prevent this, do not load print media that is smaller than the page size of the job to be printed. Open and close the printer top front cover to run the printer setup cycle and clean the transfer roll.

Toner fog or background shading appears on the page.

  • Check the photoconductor kit to make sure it is installed correctly.
  • Replace the photoconductor kit.

ABC DEF

Solving print quality problems

Problem Action

Page 101 of the Lexmark 840 user manual — ABC DEF ABC DEF
Page 101 · click to enlarge
Page 101

Troubleshooting

  • Entire page is white.
  • Make sure the packaging material is removed from the photoconductor kit.
  • Check the photoconductor kit to be sure it is installed correctly.
  • Replace the photoconductor kit.
  • Streaks appear on the page.
  • If you are using preprinted forms, make sure the ink can withstand temperatures of 230°C (446°F).
  • Replace the photoconductor kit or toner cartridge.

ABC DEF

  • Printing is too dark.
  • Change the Toner Darkness setting in the Quality menu.
  • Change the Brightness setting in the Quality menu.
  • Change the Contrast setting in the Quality menu. Note: Macintosh computer users should make sure the lines per inch (lpi) setting is not set too high in the software application.

ABC DEF ABC DEF

Characters have jagged or uneven edges.

  • Change the Print Resolution setting in the Quality menu to 600 dpi, 1200 dpi, or 2400 Image Q.
  • Enable Enhance Fine Lines.
  • If you are using downloaded fonts, verify the fonts are supported by the printer, the host computer, and the software application.

Solving print quality problems

Problem Action

Page 102 of the Lexmark 840 user manual — ABC DEF ABC DEF
Page 102 · click to enlarge
Page 102

Troubleshooting

Part or all of the page is printed in black.

Check the photoconductor kit to see if it is installed correctly.

The job prints, but the top and side margins are incorrect.

  • Make sure the Paper Size setting in the Paper menu is correct.
  • Make sure the margins are set correctly in your software application.

ABC DEF ABC DEF

  • Ghost images appear.
  • Make sure the Paper Type setting in the Paper menu is correct.
  • Replace the photoconductor kit.
  • Gray background prints.
  • The Toner Darkness setting may be too dark. Change the Toner Darkness setting in the Quality menu.
  • Adjust the Brightness to a darker setting.
  • Adjust the Contrast to a darker setting.
  • The photoconductor kit may be defective. Replace the photoconductor kit.

Some of the print is cut off on the sides, top, or bottom of the media.

Move the guides in the tray to the proper positions for the size loaded.

Print is skewed, or inappropriately slanted.

Transparency print quality is poor.

  • Use only transparencies recommended by the printer manufacturer.
  • Make sure the Paper Type setting in the Paper menu is set to Transparency.

Solving print quality problems

Problem Action

Page 103 of the Lexmark 840 user manual — Troubleshooting
Page 103 · click to enlarge
Page 103

Troubleshooting

The Quality menu operator panel options can be adjusted to help improve print quality.

Menu selection Purpose Values

Print Resolution To select printed output resolution 600 dpi 1200 dpi 2400 Image Quality*

Toner Darkness Lightens or darkens printed output and conserves toner

1–10 8* is the default setting. Select a lower number to lighten the printed output or save toner.

Brightness Adjusts the gray value of printed objects

-6 – +6 0* is the default setting.

Contrast Adjusts the contrast of printed objects 0–5 0* is the default setting.

In addition, the Enhance Fine Lines and Gray Correction options can be enabled to improve print quality. These settings are available on the driver and on the printer Embedded Web Server (EWS) interface. For more information about these options, see the driver help.

Driver option Purpose Values†

Enhance Fine Lines A selection to enable a print mode preferable for certain files containing fine line detail, such as architectural drawings, maps, electronic circuit diagrams and flow charts

On In the driver, enable the check box.

Off* In the driver, disable the check box.

Gray Correction Automatically adjusts the contrast enhancement applied to images

Auto In the driver, enable the check box.

Off* In the driver, disable the check box.

† Values marked by an asterisk (*) are the factory default settings.

Solving print quality problems

Page 104 of the Lexmark 840 user manual — Disabling operator panel menus
Page 104 · click to enlarge
Page 104

10 Administrative support

Adjusting operator panel brightness and contrast

The LCD operator panel contrast and brightness can be adjusted through the Utilities menu. For more information, see the Menus and Messages Guide.

The LCD Brightness and LCD Contrast settings are adjusted separately. To change the LCD Brightness or LCD Contrast settings:

1 Make sure your printer is on.

2 Press on the operator panel.

3 Press until Settings appears, and then press .

4 Press until Utilities Menu appears, and then press .

5 Press until appears next to the LCD setting you want to change, and then press .

6 Press to increase the brightness or contrast or press to decrease the brightness or contrast.

7 When the adjustment is complete, press .

This saves this setting as the new user default and the printer returns to Ready.

Disabling operator panel menus

Since many people could be using the printer, an administrator may choose to lock the operator panel menus to keep others from changing menu settings from the operator panel.

To disable the operator panel menus so that changes cannot be made to the printer default settings:

1 Turn the printer off.

2 Press and hold and while turning the printer on.

3 Release both buttons when Performing Self Test appears on the display.

The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.

4 Press until Panel Menus appears, and then press .

5 Press until Disable appears, and then press .

The following messages appear briefly: Submitting Selection and Disabling Menus. The operator panel returns to Panel Menus.

6 Press until Exit Config Menus appears, and then press .

Activating Menu Changes appears. The menus are disabled.

Resetting the Printer appears briefly followed by a clock. The operator panel then returns to Ready.

Administrative support

Page 105 of the Lexmark 840 user manual — Restoring factory default settings
Page 105 · click to enlarge
Page 105

Administrative support

Enabling operator panel menus

1 Turn the printer off.

2 Press and hold and while turning the printer on.

3 Release both buttons when Performing Self Test appears on the display.

The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.

4 Press until Panel Menus appears, and then press .

5 Press until Enable appears, and then press .

The following messages appear briefly in succession: Submitting Selection and Enabling Menus.

The operator panel returns to Panel Menus.

6 Press until Exit Config Menus appears, and then press .

Activating Menu Changes appears. The menus are enabled.

Resetting the Printer appears briefly followed by a clock. The operator panel then returns to Ready.

Restoring factory default settings

When you first enter the printer menus from the operator panel, you may notice an asterisk (*) to the left of a value in the menus. This asterisk indicates the factory default setting. These settings are the original printer settings. (Factory defaults may vary for different regions.)

When you select a new setting from the operator panel, Submitting Selection appears. When the Submitting Selection message disappears, an asterisk appears next to the setting to identify it as the current user default setting. These settings are active until new ones are stored or the factory defaults are restored.

To restore the original printer factory default settings:

(Resources residing in flash memory or on the optional hard disk remain unaffected.)

1 Make sure the printer is on and Ready appears on the display.

2 Press on the operator panel.

3 Press until Settings appears, and then press .

4 Press until Setup Menu appears, and then press .

5 Press until Factory Defaults appears, and then press .

6 Press until Restore Now appears, and then press .

7 The message Restoring Factory Defaults appears, followed by the Ready message.

When you select Restore:

  • No other button actions are available on the operator panel while Restoring Factory Defaults appears.
  • All menu settings return to the factory default values, except:

– The operator panel Display Language setting in the Setup menu. – All settings in the Parallel menu, Serial menu, Network menu, and USB menu.

Enabling operator panel menus

Page 106 of the Lexmark 840 user manual — Disabling Power Saver
Page 106 · click to enlarge
Page 106

Administrative support

Adjusting Power Saver

To adjust the Power Saver setting:

1 Make sure the printer is on and Ready appears on the display.

2 Press on the operator panel.

3 Press until Settings appears, and then press .

4 Press until Setup Menu appears, and then press .

5 Press until Power Saver appears, and then press .

6 Using the numeric pad or the right and left arrows on the operator panel, enter the number of minutes for the printer to wait before entering Power Saver.

The settings available range from 2–240 minutes. If you want to turn Power Saver off, see Disabling Power Saver on page 106.

7 Press .

Submitting Selection appears.

more information, see the Technical Reference available on our Lexmark Web site at www.lexmark.com.

Disabling Power Saver

Disabling Power Saver is a two step process. First, you must turn the variable on, and then select the variable. To disable Power Saver:

1 Turn the printer off.

2 Press and hold and while turning the printer on.

3 Release both buttons when Performing Self Test appears on the display.

The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.

4 Press until Energy Conserve appears, and then press .

5 Press until Off appears, and then press .

Submitting Selection appears.

The operator panel returns to Energy Conserve.

6 Press until Exit Config Menus appears, and then press .

Resetting the Printer appears briefly followed by a clock. The operator panel then returns to Ready.

7 Make sure Ready appears.

8 Press on the operator panel.

9 Press until Settings appears, and then press .

10 Press until Setup Menu appears, and then press .

11 Press until Power Saver appears, and then press .

12 Use either the numeric keypad or the right and left arrows to enter 0 (zero). Disabled appears, and then press

Submitting Selection appears. Power Saver is now disabled.

Adjusting Power Saver

Page 107 of the Lexmark 840 user manual — Administrative support
Page 107 · click to enlarge
Page 107

Administrative support

Encrypting the disk

unaffected.)

1 Turn the printer off.

2 Press and hold and while turning the printer on.

3 Release both buttons when Performing Self Test appears on the display.

The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.

4 Press until Disk Encryption appears, and then press .

5 Press until Enable appears, and then press .

Contents will be lost. Continue? appears.

6 Press until Yes appears, and then press .

The Encrypting Disk progress bar appears.

7 When disk encryption has finished, click .

8 Press until Exit Config Menu appears, and then press .

To disable disk encryption:

1 Turn the printer off.

2 Press and hold and while turning the printer on.

3 Release both buttons when Performing Self Test appears on the display.

The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.

4 Press until Disk Encryption appears, and then press .

5 Press until Disable appears, and then press .

Contents will be lost. Continue? appears.

6 Press until Yes appears, and then press .

The Encrypting Disk progress bar appears.

7 When disk encryption has finished, click .

8 Press until Exit Config Menu appears, and then press .

Encrypting the disk

Page 108 of the Lexmark 840 user manual — Supporting SNMPv3 (Simple Network Management Protocol version 3)
Page 108 · click to enlarge
Page 108

Administrative support

Setting security using the Embedded Web Server (EWS)

You can enhance the security of network communications and device configuration by using the advanced security options. These features are available through the Web page of the device.

Setting the system password

Setting the system password protects configuration of the Embedded Web Server. A system password is also required for Secure mode and confidential communication with MVP.

To set the system password:

1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http: //ip_address/.

2 Click Configuration.

3 Under Other Settings, click Security.

4 Click Create Password, if one has not been set previously. If a password has already been set, click Change or Remove Password.

Using the secure Embedded Web Server

The SSL (Secure Sockets Layer) allows for secure connections to the Web server within the print device. You can connect to the Embedded Web Server more securely by connecting to the SSL port instead of the default HTTP port. The SSL port connection will encrypt all Web server network communications between the PC and the printer. To connect to the SSL port:

Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: https: //ip_address/.

Supporting SNMPv3 (Simple Network Management Protocol version 3)

SNMPv3 protocol allows for encrypted and authenticated network communications. It also lets the administrator select a desired level of security. Prior to use, at least one user name and password must be established from the settings page. To configure for SNMPv3 through the Embedded Web Server of the printer:

1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.

2 Click Configuration.

3 Under Other Settings, click Network/Ports.

4 Click SNMP.

SNMPv3 authentication and encryption has three levels of support:

  • No authentication and no encryption
  • Authentication with no encryption
  • Authentication and encryption

Setting security using the Embedded Web Server (EWS)

Page 109 of the Lexmark 840 user manual — Using Secure mode
Page 109 · click to enlarge
Page 109

Administrative support

Supporting IPSec (Internet Protocol Security)

IP Security protocol provides authentication and encryption of communications at the network layer allowing all application and network communications over the IP protocol to be secure. IPSec can be set up between the printer and up to five hosts, using both IPv4 and IPv6. To configure IPSec through the Embedded Web Server:

1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/

2 Click Configuration.

3 Under Other Settings, click Network/Ports.

4 Click IPSec.

Two types of authentication are supported for IPSec:

  • Shared Key Authentication —Any ASCII phrase shared among all the participating hosts. This is the easiest way to configure when only a few hosts on the network use IPSec.
  • Certificate Authentication —Allows any hosts or subnet of hosts to authenticate for IPSec. Each host must have a public/private key pair. Validate Peer Certificate is enabled by default, requiring each host to have a signed certificate and the authority certificate must be installed. Each host must have its identifier in the Subject Alternate Name of the signed certificate.

place.

Using Secure mode

You can configure the TCP and UDP ports to one of three modes:

  • Disabled —Never allows network connections to this port.
  • Secure and Unsecure —Allows the port to remain open, even in Secure mode.
  • Unsecured Only —Allows the port to only open when the printer is not in Secure mode

Unsecure will be open.

To configure the Secure mode for TCP and UDP ports from the Embedded Web Server:

1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.

2 Click Configuration.

3 Under Other Settings, click Network/Ports.

4 Click TCP/IP Port Access.

Setting security using the Embedded Web Server (EWS)

Page 110 of the Lexmark 840 user manual — Locking the operator panel menus
Page 110 · click to enlarge
Page 110

Administrative support

Using 802.1x Authenticating

802.1x port authentication allows the printer to join networks that require authentication before allowing access. 802.1x port authentication can be used with the WPA (Wi-Fi Protected Access) feature of an optional internal wireless print server to provide WPA-Enterprise security support.

Support for 802.1x requires the establishment of credentials for the printer. The printer must be known to the Authentication Server (AS). The AS will allow network access to devices presenting a valid set of credentials which typically involves a name/password combination and possibly a certificate. The AS will allow network access to printers presenting a valid set of credentials. You can manage the credentials by using the Embedded Web Server of the printer. To use certificates as part of the credentials:

1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.

2 Click Configuration.

3 Under Other Settings, click Network/Ports.

4 Click Certificate Management.

To enable and configure 802.1x on the Embedded Web Server after installing the required certificates:

1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.

2 Click Configuration.

3 Under Other Settings, click Network/Ports.

4 Click 802.1x Authentication.

Authentication.

Locking the operator panel menus

Operator Panel Menu Lockout lets you create a PIN number and choose specific menus to lock. Each time a locked menu is selected, the user will be prompted to enter the correct PIN at the operator panel. The PIN does not affect any access through the EWS. To lock operator panel menus:

1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.

2 Click Configuration.

3 Under Other Settings, click Security.

4 Click Menu Lockout Setup.

Setting security using the Embedded Web Server (EWS)

Page 111 of the Lexmark 840 user manual — Confidential Print Setup
Page 111 · click to enlarge
Page 111

Administrative support

Printing Lockout

Printing Lockout lets you lock or unlock a printer using an assigned PIN. When locked, every job the printer receives will buffer to the hard disk. A user can print jobs only by entering the correct PIN on the operator panel. You can assign a PIN through the Web page of the device.

can be retrieved from a locked printer.

To set Printing Lockout:

1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.

2 Click Configuration.

3 Under Other Settings, click Security.

4 Click Printer Lockout PIN.

Confidential Print Setup

Confidential Print Setup lets you designate a maximum number of PIN entry attempts and set an expiration time for print jobs. When a user exceeds a specific number of PIN entry attempts, all of that user’s print jobs are deleted. When a user has not printed their jobs within a designated time period, the print jobs are deleted. To activate Confidential Print Setup:

1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.

2 Click Configuration.

3 Under Other Settings, click Security.

4 Click Confidential Print Setup.

Setting security using the Embedded Web Server (EWS)

Page 112 of the Lexmark 840 user manual — Federal Communications Commission (FCC) compliance information statement
Page 112 · click to enlarge
Page 112

Notices

  • Licensing notice

Licensing notice

  • Electronic emission notices

The printer resident software contains software developed and copyrighted by Lexmark. In addition, the printer resident software may contain:

  • The United Kingdom Telecommunications Act 1984
  • Noise emission levels
  • Lexmark modified software licensed under the provisions of the GNU General Public License version 2 and/or the GNU Lesser General Public License version 2.1
  • Software licensed under the BSD license
  • Software licensed under other licenses Click the title of the document you want to review:
  • ENERGY STAR
  • Waste from Electrical and Electronic Equipment (WEEE) directive
  • Laser notice
  • BSD License and Warranty statements
  • GNU General Public License
  • Open Source License The Lexmark modified third-party software covered by these thirdparty licenses is free software; you can redistribute it and/or modify it under the terms of the licenses referenced above. These licenses do not provide you any rights to the Lexmark copyrighted software in this printer. Since the third-party licensed software the Lexmark modifications are based on is supplied explicitly without warranty, use of the Lexmark modified version is similarly provided without warranty. See the warranty disclaimers in the referenced licenses for additional details. To obtain source code files for the Lexmark modified GNU licensed software, launch the drivers CD that shipped with your printer and click Contact Lexmark . For source code that is required to be made available with the product, see the publications CD in the en/OpenSource directory.
  • Radio frequency statements
  • European Community (EC) directives conformity
  • India emissions notice
  • Statement of Limited Warranty for Lexmark W840

Electronic emission notices

Federal Communications Commission (FCC) compliance information statement

The Lexmark W840, Machine Type 4024, has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The FCC Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

Page 113 of the Lexmark 840 user manual — Korean MIC statement
Page 113 · click to enlarge
Page 113

Notices

interference, in which case the user will be required to correct the interference at his own expense. The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment. Note: To assure compliance with FCC regulations on electromagnetic interference for a Class A computing device, use a properly shielded and grounded cable such as Lexmark part number 12A2405 for USB attach or 1329605 for parallel attach. Use of a substitute cable not properly shielded and grounded may result in a violation of FCC regulations.

The United Kingdom Telecommunications Act 1984

This apparatus is approved under the approval number NS/G/1234/ J/100003 for the indirect connections to the public telecommunications systems in the United Kingdom.

Noise emission levels

The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.

Industry Canada compliance statement

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

1-meter average sound pressure, dBA

Avis de conformité aux normes de l’industrie du Canada

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

ENERGY STAR

Lexmark 840 — ENERGY STAR diagram (page 113)
Fig. 73

European Community (EC) directives conformity

The EPA ENERGY STAR Office Equipment program is a partnership effort with office equipment manufacturers to promote the introduction of energy-efficient products and to reduce air pollution caused by power generation. Companies participating in this program introduce products that power down when they are not being used. This feature will cut the energy used by up to 50 percent. Lexmark is proud to be a participant in this program. As an ENERGY STAR Partner, Lexmark International, Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

A declaration of conformity with the requirements of the directives has been signed by the Director of Manufacturing and Technical Support, Lexmark International, S.A., Boigny, France. This product satisfies the Class A limits of EN 55022 and safety requirements of EN 60950.

Radio interference notice

Japanese VCCI notice

Waste from Electrical and Electronic Equipment (WEEE) directive

Lexmark 840 — Japanese VCCI notice diagram (page 113)
Fig. 74 · Japanese VCCI notice

Korean MIC statement

If this symbol appears on your product, the accompanying statement is applicable.

Lexmark 840 — Korean MIC statement diagram (page 113)
Fig. 75 · Korean MIC statement

The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products. If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.

This equipment has undergone EMC registration as a business product. It should not be used in a residential area.

Printing 56 · Idling 30

Page 114 of the Lexmark 840 user manual — Avis de conformité aux normes de l’industrie du Canada
Page 114 · click to enlarge
Page 114

Notices

Laser notice

European Community (EC) directives conformity

The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1. Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 5 milliwatt gallium arsenide laser operating in the wavelength region of 770-795 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.

This product is in conformity with the protection requirements of EC Council directives 89/336/EEC, 73/23/EEC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment. Compliance is indicated by the CE marking.

A declaration of conformity with the requirements of the directives is available from the Director of Manufacturing and Technical Support, Lexmark International, S. A., Boigny, France. This product satisfies the limits of EN 55022 (Class A); safety requirements of EN 60950; radio spectrum requirements of ETSI EN 300 330-1 and ETSI EN 300 330-2; and the EMC requirements of EN 55024, ETSI EN 301 489-1 and ETSI EN 301 489-3.

LUOKAN 1 LASERLAITE

VAROITUS! Laitteen käyttäminen muulla kuin tässä käyttoohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

KLASS 1 LASER APPARAT

Hereby, Lexmark International Inc., declares that this Short Range Device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

VARNING! Om apparaten används på annat sätt än i denna bruksanvisning specificerats, kan avnändaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.

Valmistaja Lexmark International Inc. vakuuttaa täten että Short Range Device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Radio frequency statements

Exposure to radio frequency radiation

Hierbij verklaart Lexmark International Inc. dat het toestel Short Range Device in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG

The radiated output power of this device is far below the FCC radio frequency exposure limits. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC.

Bij deze verklaart Lexmark International Inc. dat deze Short Range Device voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.

Industry Canada compliance statement

This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.

Par la présente Lexmark International Inc. déclare que l'appareil Short Range Device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE

Par la présente, Lexmark International Inc. déclare que ce Short Range Device est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables

Avis de conformité aux normes de l’industrie du Canada

Cet appareil est conforme à la spécification RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne peut engendrer aucune interférence et (2) il doit accepter toute interférence qu'il reçoit, y compris celles qui peuvent altérer son fonctionnement.

Härmed intygar Lexmark International Inc. att denna Short Range Device står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Undertegnede Lexmark International Inc. erklærer herved, at følgende udstyr Short Range Device overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF

Show 6 more labels / short text on this page
English · Finnish · Dutch · French · Swedish · Danish
Page 115 of the Lexmark 840 user manual — Limited warranty
Page 115 · click to enlarge
Page 115

Notices

Hiermit erklärt Lexmark International Inc., dass sich dieser/diese/dieses Short Range Device in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi)

Lexmark 840 — Notices diagram (page 115)
Fig. 76 · Notices

Lexmark International Inc., deklarujemy z pelna odpowiedzialnoscia, ze wyrób Short Range Device spelnia podstawowe wymagania i odpowiada warunkom zawartym w dyrektywie 1999/5/EC

Lexmark International Inc. týmto vyhlasuje, že tento Short Range Device vyhovuje technickým požiadavkám a ïalším ustanoveniam smernice 1999/5/ES, ktoré sa na tento výrobok vz″ahujú.

Hiermit erklärt Lexmark International Inc. die Übereinstimmung des Gerätes Short Range Device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien)

S tem dokumentom Lexmark International Inc., izjavlja, da je ta Short Range Device v skladu z bistvenimi zahtevami in z drugimi ustreznimi dolocili Direktive 1999/5/EC

Με την παρουσα Lexmark International Inc. δηλωνει οτι Short Range Device συµµορφωνεται προσ τισ ουσιωδεισ απαιτησεισ και τισ λοιπεσ σΧετικεσ διαταξεισ τησ οδηγιασ 1999/5/EK.

India emissions notice

Con la presente Lexmark International Inc. dichiara che questo Short Range Device è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/ 5/CE.

This device uses very low power low range RF communication that has been tested and found not to cause any interference whatsoever. The manufacturer is not responsible in case of any disputes arising out of requirement of permissions from any local authority, regulatory bodies or any organization, required by the end-user to install and operate this product at his premises.

Por medio de la presente Lexmark International Inc. declara que el Short Range Device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE

Lexmark International Inc. declara que este Short Range Device está conforme com os requisitos essenciais e outras provisões da Directiva 1999/5/ CE.

Statement of Limited Warranty for Lexmark W840

Lexmark International Inc. tímto prohlašuje, že tento výrobek s typovým oznacením Short Range Device vyhovuje základním požadavkum a dalším ustanovením smernice 1999/5/ES, které se na tento výrobek vztahují.

Lexmark International, Inc. Lexington, KY

Lexmark International Inc. ezennel kijelenti, hogy ez a Short Range Device termék megfelel az alapveto követelményeknek és az 1999/5/EC irányelv más vonatkozó ndelkezéseinek.

This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country-specific warranty information that came with your product. This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as "Remarketer."

Käesolevaga kinnitab Lexmark International Inc. seadme Short Range Device vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Limited warranty

Ar šo Lexmark International Inc. deklare, ka Short Range Device atbilst Direktivas 1999/5/EK butiskajam prasibam un citiem ar to saistitajiem noteikumiem.

Lexmark warrants that this product:

  • Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
  • Is, during normal use, free from defects in material and workmanship If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option). If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product. If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the

Lexmark International Inc. deklaruoja, kad irenginys Short Range Device tenkina 1999/5/EB Direktyvos esminius reikalavimus ir kitas sios direktyvos nuostatas

Hawnhekk, Lexmark International Inc., jiddikjara li dan Short Range Device jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 1999/5/EC

Show 11 more labels / short text on this page
German · Greek · Italian · Spanish · Portuguese · Czech · Hungarian · Estonian · Latvian · Lithuanian · Maltese
Page 116 of the Lexmark 840 user manual — Extent of limited warranty
Page 116 · click to enlarge
Page 116

Notices

remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.

CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.

Limited warranty service

The warranty period starts on the date of original purchase and ends 12 months later as shown on the purchase receipt provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Paper Feed items, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a "Life Warning" or "Scheduled Maintenance" message for such item. To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location. When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item. The replacement item assumes the remaining warranty period of the original product. Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances. Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark). For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area, contact on the World Wide Web at http://support.lexmark.com Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.

Limitation of liability

Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph. Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim. This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.

Additional rights

Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you. This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.

Extent of limited warranty

Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product. Warranty service does not include repair of failures caused by:

  • Modification or unauthorized attachments
  • Accidents, misuse, abuse or use inconsistent with Lexmark user's guides, manuals, instructions or guidance.
  • Unsuitable physical or operating environment
  • Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
  • Operation of a product beyond the limit of its duty cycle
  • Use of printing media outside of Lexmark specifications
  • Modification, refurbishment, repair, refilling or remanufacture of products by a third party, supplies or parts.
  • Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR
Page 118 of the Lexmark 840 user manual — Table of contents
Page 118 · click to enlarge
Page 118

Table of contents

Contentsp.3Learning about the printerp.6Printer overviewp.6Basic modelp.6Configured modelp.7Understanding the printer operator panelp.9Installing drivers for local printingp.11Windowsp.11Using Windows Server 2003, Windows2000, WindowsXP, Windows98SE, WindowsMe, or WindowsNTp.11Using Windows 95 and Windows 98 (first edition)p.12Serial printingp.13Macintoshp.15Creating a queue in Print Center / Printer Setup Utility (MacOSX)p.15UNIX/Linuxp.16Installing drivers for network printingp.17Printing a network setup pagep.17Assigning a printer IP addressp.17Verifying the IP settingsp.18Windowsp.18Supported printer driversp.18Supported network printer portsp.18Direct printing using Windows98SE, Me, WindowsNT4.0, Windows2000, WindowsXP, or WindowsSer...p.19Shared printing using WindowsNT 4.0, Windows2000, WindowsXP, or WindowsServer2003p.20Configuring Drag‘N’Printp.21Macintoshp.22Mac OS Xp.22MacOS9.xp.23UNIX/Linuxp.24NetWarep.24Installing optionsp.25Accessing the printer system boardp.26Installing a printer memory cardp.28Installing a flash memory or firmware cardp.29Installing an optioncardp.30Installing a hard diskp.32Replacing the access panelp.34Understanding paper and specialty media guidelinesp.35Supported print mediap.35Selecting print mediap.42Paperp.42Transparenciesp.45Envelopesp.45Labelsp.46Card stockp.47Storing print mediap.47Avoiding jamsp.47Printingp.49Loading standard or optional 500-sheet traysp.49Loading the multipurpose feederp.52Loading the 2000-sheet dual input traysp.55Loading the 2000-sheet high capacity feederp.56Loading Letter or A4 size print media in the short-edge feed orientationp.58Setting up trays with different orientationsp.58Linking traysp.59Identifying and linking output binsp.60Linking output binsp.60Sending a job to printp.61Printing from a USB flash memory devicep.62Canceling a print jobp.63Canceling a job from the printer operator panelp.63Canceling a job from a computer running Windowsp.63Canceling a job from a Macintosh computerp.64Printing the menu settings pagep.64Printing a network setup pagep.65Printing a font sample listp.65Printing a directory listp.65Printing confidential and held jobsp.65Printing a confidential jobp.65Printing and deleting held jobsp.67Printing A5/Statement or JIS-B5/Executive sizesp.69Maintaining the printerp.70Storing suppliesp.70Determining the status of suppliesp.70Photoconductor kit end-of-lifep.71Conserving suppliesp.71Ordering suppliesp.71Ordering a toner cartridgep.71Ordering a photoconductor kitp.71Maintenance kitp.72Ordering staple cartridgesp.72Recycling Lexmark productsp.72Clearing jamsp.73Identifying jamsp.73Access doors and traysp.74Understanding jam messagesp.75Clearing printer jamsp.75250 Paper Jam Check MP Feederp.7524x Paper Jam Check Tray <x>p.76200, 201, and 202 Paper Jam Check Door Ap.79203 Paper Jam Check <Areas A/E>p.80230 Paper Jam Check Door <A, E, D>p.82231 Paper Jam Check <A, D>p.84Clearing Area Bp.85Clearing Area Cp.8828x Paper Jam Check Finisherp.90Clearing staple jamsp.92Troubleshootingp.94Online customer supportp.94Calling for servicep.94Checking an unresponsive printerp.94Printing multiple-language PDFsp.95Solving printing problemsp.95Solving option problemsp.97Solving 2000-sheet drawer problemsp.98Solving paper feed problemsp.99Solving print quality problemsp.100Administrative supportp.104Adjusting operator panel brightness and contrastp.104Disabling operator panel menusp.104Enabling operator panel menusp.105Restoring factory default settingsp.105Adjusting Power Saverp.106Disabling Power Saverp.106Encrypting the diskp.107Setting security using the Embedded Web Server (EWS)p.108Setting the system passwordp.108Using the secure Embedded Web Serverp.108Supporting SNMPv3 (Simple Network Management Protocol version 3)p.108Supporting IPSec (Internet Protocol Security)p.109Using Secure modep.109Using 802.1x Authenticatingp.110Locking the operator panel menusp.110Printing Lockoutp.111Confidential Print Setupp.111Noticesp.112Indexp.117
Page 119 of the Lexmark 840 user manual — Index
Page 119 · click to enlarge
Page 119

Index

W

verify print 67 · Windows 18

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Some documents do not print.The documents contain unavailable fonts.1 Open the document you want to print in Adobe Acrobat. 2 Click the printer icon. The Print dialog appears. 3 Check the Print as image box. 4 Click OK. p.95
The operator panel display is blank or displays only diamonds.The printer self test failed.Turn the printer off, wait about 10 seconds, and turn the printer back on. If the Performing Self Test and Ready messages do not appear, turn the printer off and call for service. p.95
The message USB device unsupported appears when using a USB device.The USB device you are using may not be supported or has an error. Only specific USB flash memory devices are supported.For information regarding tested and approved USB flash memory devices, see our Lexmark Web site at http:// support.lexmark.com and click on KnowledgeBase to search for Direct USB printing. p.95
Jobs do not print.The printer is not ready to receive data.Make sure Ready or Power Saver appears on the display before sending a job to print. Press to return the printer to the Ready state. p.95
Jobs do not print.The specified output bin is full.Remove the stack of paper from the output bin, and then press . p.95
Jobs do not print.The specified tray is empty.Load paper in the tray. p.95
Jobs do not print.You are using the wrong printer driver or are printing to a file.• Verify you are using the printer driver associated with your printer. • If you are using a USB Direct interface, make sure you are running Windows 98/Me, Windows 2000, Windows XP, or Windows Server 2003 and using a Windows 98/Me, Windows 2000, Windows XP, or Windows Server 2003 compatible printer driver. p.95
Jobs do not print.Your internal print server is not set up properly or is not connected properly.Verify that you have properly configured the printer for network printing. See the drivers CD or the Lexmark Web site for information. p.95
Jobs do not print.You are using the wrong interface cable, or the cable is not securely connected.Make sure you are using a recommended interface cable. Make sure the connection is secure. p.95
Held jobs do not print.A formatting error has occurred.• Print the job. (Only part of the job may print.) • Delete the job. • Free up additional printer memory by scrolling through the list of held jobs and deleting others you have sent to the printer. p.96
Held jobs do not print.The printer has insufficient memory. p.96
Held jobs do not print.The printer has received invalid data.Delete the job. p.96
Job takes longer than expected to print.The job is too complex.Reduce the complexity of your print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job. p.96
Job takes longer than expected to print.Page Protect is set to On.Set Page Protect to Off from the Setup Menu. For more information, see the Menus and Messages Guide. p.96
Job prints from the wrong tray or on the wrong paper or specialty media.The operator panel menu settings do not match the media loaded in the tray.Make sure the Paper Size and Paper Type specified in the printer driver match the paper size and type in the tray. p.96
Incorrect characters print.You are using an incompatible parallel cable.If you are using a parallel interface, make sure you are using an IEEE 1284-compliant parallel cable. We recommend Lexmark part number 1329605 (10 ft) or 1427498 (20 ft) for the standard parallel port. p.96
Incorrect characters print.The printer is in Hex Trace mode.If Ready Hex appears on the display, you must exit Hex Trace mode before you can print your job. Turn the printer off and back on to exit Hex Trace mode. p.96
Tray linking does not work.Tray linking is not configured properly.• Make sure both the size and type of media are the same in both trays. • Make sure the paper guides in the trays are set for the correct size media. • Make sure the menu values for both size and type are set correctly in the Paper menu. • See Linking trays on page 59 or see the Menus and Messages Guide for more information. p.96
Large jobs do not collate.Collate is not set to On.Set Collation to On in the Finishing Menu or through the printer driver. Note: Setting Collation to Off in the driver overrides the setting in the Finishing Menu. See the Menus and Messages Guide for more information. p.96
Large jobs do not collate.The job is too complex.Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job. p.96
Large jobs do not collate.The printer does not have enough memory.Add printer memory or an optional hard disk. p.96
Unexpected page breaks occur.The job has timed out.Set Print Timeout to a higher value from the Setup Menu. See the Menus and Messages Guide for more information. p.96
The elevator tray does not raise when the loading door is closed, or the elevator tray does not lower when the door is opened and the elevator button is pushed.Check the following: • The printer is properly attached to the 2000-sheet drawer. • The printer is powered on. • The power cord is plugged firmly into the back of the 2000-sheet drawer. • The power cord is plugged into an outlet. • The outlet has power. p.98
The elevator tray lowers unexpectedly.Check to see if your printer is out of print media or has a jam. p.98
More than one sheet of print media is fed or a sheet is fed improperly.Remove the print media in the printer paper path, and check the stack to ensure the print media has been loaded properly. Be sure to remove the top and bottom sheets of each ream of paper that is loaded. p.98
A jam occurs. p.98
Rubber feed rollers do not turn to advance print media.Check the following: • The power cord is plugged firmly into the back of the 2000-sheet drawer. • The power cord is plugged into an outlet. • The outlet has power. p.98
Consistent misfeeds or jams in the drawer.Try the following: • Flex the paper. • Turn the print media over. Check the following: • Drawer is properly installed. • Print media is loaded correctly. • Print media is not damaged. • Print media meets specifications. • Guides are positioned correctly for the print media size selected. p.98
Service messagesA service message indicates printer failure that may require service. Turn the printer off, wait about 10 seconds, and then turn the printer on. If the error recurs, write down the error number, the problem, and a detailed description. Call for service. p.98
Paper frequently jams.You are using paper that does not meet the printer specifications.Use recommended paper and other specialty media. See the Card Stock & Label Guide available on our Lexmark Web site at www.lexmark.com for detailed specifications. See Avoiding jams on page 47 for information that can help prevent jams from occurring. p.99
Paper frequently jams.You have loaded too much paper or too many envelopes.Make sure the stack of paper you load does not exceed the maximum stack height indicated in the tray or on the multipurpose feeder. p.99
Paper frequently jams.Guides in the selected tray are not set to the appropriate position for the size paper loaded.Move the guides in the tray to the correct position. p.99
Paper frequently jams.The paper has absorbed moisture due to high humidity.Load paper from a fresh package. Store paper in its original wrapper until you load it. See Storing print media on page 47 for more information. p.99
The Paper Jam message remains after you remove the jammed paper.You have not pressed or have not cleared the entire paper path.Clear paper from the entire paper path, and then press . See Clearing printer jams on page 75 for more information. p.99
The page that jammed does not reprint after you clear the jam.Jam Recovery in the Setup menu is set to Off.Set Jam Recovery to Auto or On. See the Menus and Messages Guide for more information. p.99
Blank pages feed into the output bin.An incorrect media type is loaded in the tray being printed from.Load the correct type media for your print job, or change the Paper Type to match the type of media loaded. See the Menus and Messages Guide for more information. p.99
Print is too light. ABC DEF• The toner may be low. • Change the Toner Darkness setting in the Quality menu. • Change the Brightness setting in the Quality menu. • Change the Contrast setting in the Quality menu. • If you are printing on an uneven print surface, change the Paper Weight and Paper Texture settings in the Paper menu. • Verify the correct print media is being used. p.100
Toner smears or print comes off the page. ABC DEF• If you are printing on an uneven print surface, change the Paper Weight and Paper Texture settings in the Paper menu. • Verify the print media is within the printer specifications. See Understanding paper and specialty media guidelines on page 35 for more details. If the problem continues, contact the Lexmark Customer Support Center at http://support.lexmark.com. p.100
Toner appears on the back of the printed page.Toner is on the transfer roll. To help prevent this, do not load print media that is smaller than the page size of the job to be printed. Open and close the printer top front cover to run the printer setup cycle and clean the transfer roll. p.100
Toner fog or background shading appears on the page. ABC DEF• Check the photoconductor kit to make sure it is installed correctly. • Replace the photoconductor kit. p.100
Entire page is white.• Make sure the packaging material is removed from the photoconductor kit. • Check the photoconductor kit to be sure it is installed correctly. • Replace the photoconductor kit. p.101
Streaks appear on the page. ABC DEF• If you are using preprinted forms, make sure the ink can withstand temperatures of 230°C (446°F). • Replace the photoconductor kit or toner cartridge. p.101
Printing is too dark. ABC DEF• Change the Toner Darkness setting in the Quality menu. • Change the Brightness setting in the Quality menu. • Change the Contrast setting in the Quality menu. Note: Macintosh computer users should make sure the lines per inch (lpi) setting is not set too high in the software application. p.101
Characters have jagged or uneven edges.• Change the Print Resolution setting in the Quality menu to 600 dpi, 1200 dpi, or 2400 Image Q. • Enable Enhance Fine Lines. • If you are using downloaded fonts, verify the fonts are supported by the printer, the host computer, and the software application. p.101
Part or all of the page is printed in black.Check the photoconductor kit to see if it is installed correctly. p.102
The job prints, but the top and side margins are incorrect. ABC DEF• Make sure the Paper Size setting in the Paper menu is correct. • Make sure the margins are set correctly in your software application. p.102
Ghost images appear.• Make sure the Paper Type setting in the Paper menu is correct. • Replace the photoconductor kit. p.102
Gray background prints.• The Toner Darkness setting may be too dark. Change the Toner Darkness setting in the Quality menu. • Adjust the Brightness to a darker setting. • Adjust the Contrast to a darker setting. • The photoconductor kit may be defective. Replace the photoconductor kit. p.102
Some of the print is cut off on the sides, top, or bottom of the media.Move the guides in the tray to the proper positions for the size loaded. p.102
Print is skewed, or inappropriately slanted. p.102
Transparency print quality is poor.• Use only transparencies recommended by the printer manufacturer. • Make sure the Paper Type setting in the Paper menu is set to Transparency. p.102

Ask about the Lexmark 840

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lexmark 840

Be the first to ask — other owners or our team will answer.

Original document

Lexmark 840 manual PDF

119 pages·2.7 MB·Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…