
User’s Guide
March 2005
www.lexmark.com
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. © 2005 Lexmark International, Inc. All rights reserved. 740 West New Circle Road Lexington, Kentucky 40550

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time. Comments about this publication may be addressed to Lexmark International, Inc., Department F95/032-2, 740 West New Circle Road, Lexington, Kentucky 40550, U.S.A. In the United Kingdom and Eire, send to Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. You can purchase additional copies of publications related to this product by calling 1-800-553-9727. In the United Kingdom and Eire, call +44 (0)8704 440 044. In other countries, contact your point of purchase. References in this publication to products, programs, or services do not imply the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.


Identifying printers
Use the following table to determine the features and options of your Lexmark™ T640, T642, or T644 printer.
The illustrations aid you in determining the installation location of options attached to the printer. For more information about installing input options, see Installing and removing options or the instructions that came with the option.
The printer is available in three base models The following table indicates some of the differences between the models.
telephone, during a lightning storm.
Learning about the printer

Configured models
The following illustrations show a standard network and fully configured printer. If you attach print media handling options to the printer, it may look more like the fully configured model. Items denoted with an asterisk (*) are options.
Standard network Fully configured


Tray 1 (integrated tray or standard tray)
Tray 2* (250 or 500 sheets)
Tray 3* (250 or 500 sheets)
Tray 1 (integrated tray or standard tray)
Tray 4* (250 or 500 sheets)
The standard tray holds 250 sheets for the T640 and 500 sheets for the T642 and T644.
Tray 5* (2000-sheet drawer)
stand or printer base if you are using a 2000-sheet drawer, a duplex unit and an input option, or more than one input option. If you purchased a multifunction printer (MFP) that scans, copies, and faxes, you may need additional furniture. See www.lexmark.com/multifunctionprinters for more information.

A number of menus are available to make it easy for you to change printer settings. The diagram shows the menu index on the operator panel and the menus and items available under each menu. For more information about menus and menu items, see the Menus and Messages book on the publications CD.
Paper Menu Reports Settings
Settings Setup Menu Finishing Menu Quality Menu Utilities Menu PDF Menu PostScript Menu PCL Emul Menu HTML Menu Image Menu
Security Max Invalid PIN Job Expiration
Paper Menu Default Source Paper Size/Type Configure MP Envelope Enhance Substitute Size Paper Texture Paper Weight Paper Loading Custom Types Universal Setup Bin Setup
Reports Menu Settings Page Device Statistics Network Setup Page Network Setup Page Profiles List NetWare Setup Page Print Fonts Print Directory
Help Print All Print Quality Printing Guide Supplies Guide Media Guide Menu Map Information Guide Connection Guide Moving Guide
Network/Ports IPv6 TCP/IP Standard Network Network Standard USB USB Parallel Parallel Serial NetWare AppleTalk LexLink
Identifying printers

Understanding the printer operator panel
The operator panel on the printer is a 4-line back-lit gray scale display that can show both graphics and text. The Back, Menu, and Stop buttons are located to the left of the display, the navigation buttons are located below the display, and the numeric pad is located to the right of the display.
The use of the buttons and the layout of the display panel are described in the following table.
Understanding the printer operator panel

Understanding the printer operator panel

A local printer is a printer attached to the computer using a USB or parallel cable. The local printer is intended to be used by the computer to which it is attached. If attaching a local printer, you must install the printer driver on the computer before setting up the printer.
The printer driver is software that lets the computer communicate with the printer.
The procedure to install drivers depends on the operating system used. Use the following table to find driver installation instructions for the particular operating system. For additional help, see the documentation that shipped with the computer and your software.
Operating system Go to page
Windows Server 2003, Windows 2000, Windows XP, Windows 98 SE, Windows Me, Windows NT 4.x
Windows 95 and Windows 98 (first edition) 12
Some Windows operating systems may already include a printer driver that is compatible with the printer.
and appear in the Printers folder.
Use the drivers CD that shipped with the printer to install the custom printer driver and obtain enhanced printer features and functionality.
Drivers are also available in downloadable software packages on the Lexmark Web site at www.lexmark.com.
Using Windows Server 2003, Windows 2000, Windows XP, Windows 98 SE, Windows Me, or Windows NT
1 Insert the drivers CD.
If the CD does not launch automatically, click Start Æ Run, and type D:\Setup.exe in the Run dialog (where D is the letter of the CD-ROM drive).
system, you must have an optional Parallel 1284-B Interface Card installed and use a parallel cable.
Installing drivers for local printing

2 Click Install Printer and Software.
computer.
3 Click Agree to accept the license agreement.
4 Select Suggested, and click Next.
The Suggested option is the default installation for local and network-attached setup. To install utilities, change settings, or customize device drivers, select Custom, and follow the instructions on the screen.
5 Select Local Attach, and click Finish.
Follow the instructions on the screen. It may take some time for the drivers files to load.
6 Close the drivers CD installer application.
7 Connect the USB cable, and turn on the printer.
The Plug and Play screen appears, and a printer object is created in the Printers folder of your computer.
system, you must have an optional Parallel 1284-B Interface Card installed and use a parallel cable. The Plug and Play screen will not appear for Windows NT.
1 Turn on the computer.
2 Insert the drivers CD. If the CD launches automatically, click Exit to return to the Add Printer Wizard.
3 Click Start Æ Settings Æ Printers, and double-click Add Printer.
4 When prompted, select Local printer.
5 Click Have Disk.
computer.
6 Specify the location of the custom printer driver on the drivers CD.
The path should be similar to the following:
D:\Drivers\Print\Win_9xMe\<language>
Where D is the letter of the CD-ROM drive.
7 Click OK.
It may take some time for the drivers to load.
8 Close the drivers CD.
With serial printing, data is transferred one bit at a time. Although serial printing is usually slower than parallel printing, it is the preferred option when there is a great deal of distance between the printer and computer, or when a parallel interface is not available.
Windows

Before you can print, you must establish communication between the printer and computer. To do this:
1 Set serial parameters in the printer.
2 Install a printer driver on the attached computer.
3 Match the serial settings in the COM port.
1 Press on the operator panel.
2 Press until Reports appears, and then press .
printer.
3 Press until Menu Settings Page appears, and then press .
The printer returns to Ready.
4 Press .
5 Press until Network/Ports appears, and then press .
6 Press until Serial Standard or Serial Option X appears, and then press .
(x) is the number of the serial port.
7 Press until <Parameter> appears (where <Parameter> is the parameter required for a change), and then press .
8 Press until <Setting> appears (where <Setting> is the setting required for a change), and then press .
9 Press .
The printer returns to Serial or Serial x.
10 Print a Menu Settings page, and verify the serial parameters are correct.
a Press on the operator panel.
b Press until Reports appears, and then press .
c Press until Menu Settings Page appears, and then press .
d Look under the Standard Serial (or Serial Option X if a serial interface card is installed) heading to find the serial parameters.
Windows

Installing a printer driver
A printer driver must be installed on the computer that is connected to the printer.
Windows 95 and Windows 98 (first edition).
1 Insert the drivers CD. It should launch automatically. If the CD does not launch automatically, click Start Æ Run, and type the following in the Run dialog:
D:\Setup.exe
Where D is the letter of the CD-ROM drive.
2 Click Install Printer and Software.
3 Click Agree to accept the Printer Software License Agreement.
4 Select Custom, and click Next.
5 Select Components, and click Next.
6 Select Local, and click Next.
7 Select the printer from the list, and click Add Printer.
8 Expand the printer item listed below Selected Components.
9 Click PORT: <LPT1>, and select the desired communications port (COM1 or COM2).
10 Click Finish to complete the printer software installation.
After the printer driver is installed, set the serial parameters in the communications port assigned to the printer driver.
The serial parameters in the communications port must exactly match the serial parameters set in the printer.
1 Click Start Æ Settings Æ Control Panel, and double-click System.
2 On the Device Manager tab, click + to expand the list of available ports.
3 Select the communications port assigned to the printer (COM1 or COM2).
4 Click Properties.
5 On the Port Settings tab, set the serial parameters to the exact same serial parameters in the printer.
Look for the printer settings under the Serial Standard (or Serial Option X) heading on the previously printed Menu Settings page.
6 Click OK, and close all the windows.
7 Print a test page to verify printer installation.
a Click Start Æ Settings Æ Printers.
b Select the newly added printer.
c Click File Æ Properties.
d Click Print Test Page. When a test page prints successfully, printer setup is complete.
operating system Help.
Windows

Macintosh
Mac OS 9.x or later is required for USB printing. To print locally to a USB-attached printer, create a desktop printer icon (Mac OS 9) or create a queue in Print Center / Printer Setup Utility (Mac OS X).
Creating a queue in Print Center / Printer Setup Utility (Mac OS X)
1 Install a PostScript Printer Description (PPD) file on the computer.
a Insert the drivers CD.
b Double-click the installer package for the printer.
c Click Continue on the Welcome screen and again after viewing the Readme file.
d Click Continue after viewing the license agreement, and click Agree to accept the terms of the agreement.
e Select a Destination, and click Continue.
f On the Easy Install screen, click Install.
g Enter the password, and click OK. All the necessary software is installed on the computer.
h Click Close when installation is complete.
2 Open Finder, click Applications, and click Utilities.
3 Double-click Print Center or Printer Setup Utility.
4 Do one of the following:
1 Install a PostScript Printer Description (PPD) file on the computer.
a Insert the drivers CD.
b Double-click Classic, and double-click the installer package for the printer.
c Choose the appropriate language, and click Continue.
d Click Continue after viewing the Readme file.
e Click Continue after viewing the license agreement, and click Agree to accept the terms of the agreement.
f On the Installation Type screen, click Install. All the necessary files are installed on the computer.
g Click Close when installation is complete.
Macintosh

2 Do one of the following:
3 Double-click Desktop Printer Utility.
4 Select Printer (USB), and click OK.
5 In the USB Printer Selection section, click Change.
If the printer does not appear in the USB Printer Selection list, make sure the USB cable is properly connected, and the printer is turned on.
6 Select the name of the printer, and click OK. The printer appears in the original Printer (USB) window.
7 In the PostScript Printer Description (PPD) File section, click Auto Setup. Make sure the printer PPD matches the printer.
8 Click Create, and click Save.
9 Specify a printer name, and click Save. The printer is now saved as a desktop printer.
Local printing is supported on many UNIX and Linux platforms, such as Sun Solaris and Red Hat.
The Sun Solaris and Linux packages are available on the drivers CD and on the Lexmark Web site at www.lexmark.com. The UNIX/Linux User’s Guide in each package gives detailed instructions for installing and using Lexmark printers in UNIX and Linux environments.
All the printer driver packages support local printing using a parallel connection. The driver package for Sun Solaris supports USB connections to Sun Ray appliances and Sun workstations.
Visit the Lexmark Web site at www.lexmark.com for a complete list of supported UNIX and Linux platforms.
UNIX/Linux

Printing a network setup page
If the printer is attached to a network, print a network setup page on the printer to verify the network connection. This page also provides important information to configure the printer for network printing.
1 Make sure the printer is on.
2 Press on the operator panel.
3 Press until Reports appears, and then press .
4 Press until Network Setup Page appears, and then press .
on the display.
5 Check the first section on the network setup page, and confirm that Status is “Connected.”
If Status is “Not Connected,” the LAN drop may not be active, or the network cable may be malfunctioning. Consult a system support person for a solution, and print another network setup page to verify the printer is connected to the network.
If the network is using DHCP, an IP address is automatically assigned connecting the network cable to the printer.
1 Look for the address under the “TCP/IP” heading on the network setup page printed in Printing a network setup page.
2 Go to Verifying the IP settings, and begin with step 2.
If the network is not using DHCP, then manually assign an IP address to the printer. One of the easiest ways is to use the operator panel:
1 Press on the operator panel.
2 Press until Network/Ports appears, and then press .
3 Press until TCP/IP appears, and then press .
Standard Network appears if the printer has a network port on the printer system board. If a MarkNet N8000 series internal print server is installed, you see Network Option 1.
4 Press until Address appears, and then press .
5 Using the numeric pad, enter the IP address. When the address is entered, press .
Submitting Selection appears briefly.
6 Press until Netmask appears, and then press .
7 Using the numeric pad, enter the IP netmask. When the address is entered, press .
Submitting Selection appears briefly.
8 Press until Gateway appears, and then press .
Installing drivers for network printing

9 Using the numeric pad, enter the IP gateway. When the address is entered, press .
Submitting Selection appears briefly.
10 Press until the printer returns to Ready.
1 Print another network setup page. Look under the “TCP/IP” heading, and make sure the IP address, netmask, and gateway are correct. See Printing a network setup page if you need help.
2 Ping the printer, and verify that it responds. At a command prompt on a network computer, type ping followed by the new printer IP address (for example, 192.168.0.11).
Command prompt if using Windows 2000).
If the printer is active on the network, a reply is sent.
After the TCP/IP settings are assigned and verified, install the printer on each network computer.
In Windows environments, network printers can be configured for direct printing or shared printing. Both network printing methods require the installation of a printer driver and the creation of a network printer port.
Updated system and custom drivers are available on the Lexmark Web site at www.lexmark.com.
Custom drivers are available on the drivers CD.
For basic printer functionality, install a printer driver, and use a system network printer port, such as an LPR or a Standard TCP/IP port. The printer driver and port let you maintain a consistent user interface for use with all the printers on the network. Using a custom network port provides enhanced functionality, such as printer status alerts.
Verifying the IP settings

Follow the steps for your printing configuration and operating system to configure the network printer:
Printing configuration Operating system Go to page
Windows 98 SE, Windows NT 4.0, Windows Me, Windows 2000, Windows XP, or Windows Server 2003
Windows NT 4.0, Windows 2000, Windows XP, or Windows Server 2003
Direct printing using Windows 98 SE, Me, Windows NT 4.0, Windows 2000, Windows XP, or Windows Server 2003
To install a custom printer driver and network port:
1 Launch the drivers CD.
2 Click Install Printer and Software.
3 Click Agree to accept the license agreement.
4 Select Suggested, and click Next.
5 Select Network Attach, and click Next.
6 Select the printer model from the list, and click Next.
7 Select the printer port from the list, and click Finish to complete the installation.
If the printer port is not listed:
a Click Add Port.
b Select Lexmark Enhanced TCP/IP Port, and enter the information to create the port.
c Enter a port name.
This can be any name to associate with the printer, such as Monochrome1-lab4. After the port is created, this name appears in the list of available ports.
d Enter the IP address in the text box.
help, see Printing a network setup page and Verifying the IP settings.
8 Print a test page to verify printer installation.
Printer · Clients · Windows

Shared printing using Windows NT 4.0, Windows 2000, Windows XP, or Windows Server 2003
After connecting the printer to a Windows NT 4.0, Windows 2000, Windows XP, or Windows Server 2003 computer (which will act as a server), follow these steps to configure the network printer for shared printing:
1 Install a custom printer driver.
a Launch the drivers CD.
b Click Install Printer and Software.
c Click Agree to accept the license agreement.
d Select Suggested, and click Next.
The Suggested option is the default installation for local and network-attached setup. To install utilities, change settings, or customize device drivers, select Custom, and follow the instructions on the screen.
e Select Local Attach, and click Finish.
Follow the instructions on the screen. It may take some time for the drivers to load.
f Close the drivers CD installer application.
g Connect the USB cable, and turn on the printer.
The Plug and Play screen appears, and a printer object is created in the Printers folder of the computer. The printer is shared in step 2: “Share the printer on the network.”
Plug and Play screen will not appear for Windows NT.
h Print a test page to verify printer installation.
2 Share the printer on the network.
a Click Start Æ Settings Æ Printers.
b Select the newly added printer.
c Click File Æ Sharing.
d Select the Shared as check box, and enter a name in the text box.
e In the Alternate Drivers section, select the operating systems of all the network clients that will print to the printer.
f Click OK.
g Check the following to make sure the printer was successfully shared.

Install the printer driver (or subset) on network clients
Using the point and print method
the print job processing. This lets network clients return to applications much faster.
With this method, a subset of driver information is copied from the server to the client computer. This is just enough information to send a print job to the printer.
1 Double-click Network Neighborhood on the Windows desktop of the client computer.
2 Locate the host name of the server computer, and double-click the host name.
3 Right-click the shared printer name, and click Install.
Wait a few minutes for the driver information to be copied from the server computer to the client computer and for a new printer object to be added to the Printers folder. The time this takes varies based on network traffic and other factors.
4 Close Network Neighborhood.
5 Print a test page to verify printer installation.
Using the peer-to-peer method
With this method, the printer driver is fully installed on each client computer. Network clients retain control of driver modifications. The client computer handles the print job processing.
1 Click Start Æ Settings Æ Printers.
2 Click Add Printer to launch the Add Printer wizard.
3 Click Next.
4 Click Network Printer, and click Next.
5 Enter the printer name or URL (if on the Internet or an intranet), and click Next.
If the printer name or URL is unknown, leave the text box blank, and click Next.
6 Select the network printer from the Shared printers list. If the printer is not listed, enter the path of the printer in the text box.
The path looks similar to the following:
\\<server host name>\<shared printer name>
provide a path to available drivers.
The server host name is the name of the server computer that identifies it to the network. The shared printer name is the name assigned during the server installation process.
7 Click OK.
8 Select whether this printer will be the default printer for the client, and click Finish.
9 Print a test page to verify printer installation.
operating system Help.
Windows

Configuring Drag‘N’Print
For detailed configuration instructions, launch the drivers CD, click View Documentation, and click Software and utilities.
printer to UNIX or Macintosh computers.
To print to a network printer, each Macintosh user must install a custom PostScript Printer Description (PPD) file, and either create a desktop printer on the computer (Mac OS 9.x) or create a print queue in Print Center (Mac OS X).
Step 1: Install a custom PPD file
1 Install a PostScript Printer Description (PPD) file on the computer.
a Insert the drivers CD.
b Double-click the installer package for the printer.
c Click Continue on the Welcome screen and again after viewing the Readme file.
d Click Continue after viewing the license agreement, and click Agree to accept the terms of the agreement.
e Select a Destination, and click Continue.
f On the Easy Install screen, click Install.
g Enter the password, and click OK. All the necessary software is installed on the computer.
h Click Close when installation is complete.
Follow these steps to create a print queue using AppleTalk Printing.
1 Open Finder, click Applications, and click Utilities.
2 Double-click Print Center or Printer Setup Utility.
3 Choose Add Printer from the “Printers” menu.
4 Choose AppleTalk from the pop-up menu.
select.
5 Select the AppleTalk zone from the list.
6 Select the new printer from the list, and click Add.
Macintosh

7 Verify printer installation:
a Open Finder, click Applications, and click TextEdit.
b Choose Print from the “File” menu.
c Choose Summary from the “Copies & Pages” pop-up menu.
heading to find the default name of the printer.
Follow these steps to create a print queue using IP Printing. To create an AppleTalk print queue, see Step 2: Create a print queue in Print Center or Printer Setup Utility.
1 Open Finder, click Applications, and click Utilities.
2 Double-click Print Center or Printer Setup Utility.
3 Choose Add Printer from the “Printers” menu.
4 Choose IP Printing from the pop-up menu.
5 Enter the IP address or the printer DNS name in the Printer Address box.
6 Choose Lexmark from the “Printer Model” pop-up menu.
7 Select the new printer from the list, and click Add.
8 Verify printer installation:
a Open Finder, click Applications, and click Text Edit.
b Choose Print from the “File” menu.
c Choose Summary from the “Copies & Pages” pop-up menu.
d Do one of the following:
Step 1: Install a custom PPD file
1 Insert the drivers CD.
a Double-click Classic, and double-click the installer package for the printer.
b Choose the appropriate language, and click Continue.
c Click Continue after viewing the Readme file.
d Click Continue after viewing the license agreement, and click Agree to accept the terms of the agreement.
e On the Easy Install screen, click Install. All the necessary files are installed on the computer.
Macintosh

f Click Close when installation is complete.
1 In the Chooser, select the LaserWriter 8 driver.
2 For a routed network, select the default zone from the list. If you don’t know which zone to select, look on the Network Setup page under AppleTalk for Zone.
3 Select the new printer from the list.
4 To know which printer to select, look on the Network Setup page under the “AppleTalk” heading to find the default name of the printer.
5 Click Create.
6 Make sure there is an icon next to the printer name in the Chooser.
7 Close the Chooser window.
8 Verify printer installation.
a Click the newly created desktop printer icon.
b Choose Printing Æ Change Setup.
– If the PPD file displayed in the PostScript Printer Description (PPD) file portion of the menu is correct for the printer, printer setup is complete. – If the PPD file displayed in the PostScript Printer Description (PPD) file portion of the menu is not correct for the printer, repeat Step 1: Install a custom PPD file.
The printer supports many UNIX and Linux platforms, such as Sun Solaris and Red Hat. Visit the Lexmark Web site at www.lexmark.com for a complete list of supported UNIX and Linux platforms.
Lexmark provides a printer driver package for each supported UNIX and Linux platform. The User’s Guide in each package gives detailed instructions for installing and using Lexmark printers in UNIX and Linux environments.
These packages are available for download from the Lexmark Web site. The required driver package is also on the drivers CD.
The printer supports Novell Distributed Print Services (NDPS/iPrint). For the latest information about installing a network printer in a NetWare environment, launch the drivers CD, and click View Documentation.
UNIX/Linux

Installing input options
Floor-mounted configurations require additional furniture. You must use either a printer stand or printer base if you are using a 2000-sheet drawer, a duplex unit and an input option, or more than one input option. If you purchased an MFP that scans, copies, and faxes, you may need additional furniture. More information is available on our Lexmark Web site at www.lexmark.com/multifunctionprinters.
Install the printer and any options you have purchased in the following order:
before continuing.
For information on installing a printer stand, printer base, or 2000-sheet drawer, see the instructions included with the option.
Installing and removing options

Installing a 250-sheet or 500-sheet drawer
Optional drawers attach under the printer and optional duplex unit. The printer automatically recognizes any drawer that is installed.
A drawer consists of a tray and a support unit. The 250-sheet drawer and the 500-sheet drawer are installed the same way.
1 Remove the tray from the support unit. Remove all packing material and tape from both the support unit and the tray.


2 Place the support unit on top of any previously installed drawers, or the table or printer cabinet where you plan to use the printer.
The tab, round peg, and square holes on top of any drawer help you position the support unit so the edges are aligned properly. Make sure the support unit is securely in place.
3 Attach another optional drawer, a duplex unit, or the printer.
You can attach a label to the trays to indicate the tray number.


Installing a duplex unit
The duplex unit attaches under the printer, below the standard tray and above any drawers.
a 250-sheet standard tray, and the 500-sheet duplex unit only works with printers that have a 500- sheet standard tray. Make sure you have the appropriate duplex unit for the tray size installed in the printer.
1 Place the duplex unit on top of any installed drawers or the table or printer cabinet where you plan to use the printer.
The tab, round peg, and square holes on top of any drawer help you position the duplex unit so the edges are aligned properly. Make sure it is securely in place.

Installing a duplex unit
Tab · Square hole

Installing memory or option cards
and unplug the power cord before continuing.
You can customize the printer memory capacity and connectivity by adding optional cards. The instructions in this section help you install any of the following options:
You must access the printer system board to install printer memory, flash memory, a firmware card, or an option card.
1 Push the release latch, and lower the multipurpose feeder.
2 Push the release latch, and open the top front cover.


Installing memory or option cards

3 Press both side door latches, and open the side door.
4 Loosen, but do not remove, the six screws on the shield.

5 Slide the shield to the right, and then remove it.

Accessing the printer system board

6 Set the shield aside.
Use the illustration to locate the connector for the card you want to install.
Flash and firmware card connectors
1 Remove the system board access cover. (See Accessing the printer system board.)
printer frame before you touch a memory card.
2 Push open the latches on both ends of the memory card connector.
3 Unpack the memory card.
Avoid touching the connection points along the edge of the card. Save the packaging.
4 Align the notches on the bottom of the card with the notches on the connector.
5 Push the memory card firmly into the connector until the latches on either end of the connector snap into place.
It may require some force to fully seat the card.
Installing or removing a memory card
Option card connector · Memory card connector

6 Make sure each latch fits over the notch on the end of the card.

1 Remove the system board access cover. (See Accessing the printer system board.)
as the printer frame before you touch a memory card.
2 Push the latches away from the card on both ends of the memory card connector.
The memory card moves out of the connector as the latches open.
3 Pull the memory card out of the connector.
Avoid touching the connection points along the edge of the card.
4 Place the card into the original packaging.
If you do not have the original packaging, wrap the card in paper, and store it in a box.
5 Close both latches.


Installing or removing a memory card
Memory connector · Memory card

Installing or removing a flash memory or firmware card
Installation
1 Remove the system board access cover. (See Accessing the printer system board.)
memory or firmware card.
2 Unpack the flash memory or firmware card.
3 Holding the flash memory or firmware card by the locking clips, align the plastic pins on the card with the holes on the system board.
4 Push the flash memory or firmware card firmly into place, and release the locking clips.
The entire length of the connector on the flash memory or firmware card must touch the system board and be locked into the connector.
Be careful not to damage the connectors.

Flash memory or firmware card
Installing or removing a flash memory or firmware card
Connector

Removal
1 Remove the system board access cover. (See Accessing the printer system board.)
flash memory or firmware card.
2 Squeeze the flash memory or firmware card locking clips.
3 Pull the card out.
Avoid touching the metal pins on the bottom of the card.
4 Place the flash memory or firmware card in its original packaging.
If you do not have the original packaging, wrap the flash memory or firmware card in paper, and store it in a box.
5 If you removed an option card to access the flash memory or firmware card, reinstall the option card.

Installing or removing a flash memory or firmware card

Installing an option card
The printer has two connectors that support the following option cards:
frame before you touch an option card.
1 Locate the card connectors on the system board.
2 Remove the screw and the cover plate, and save them.
If you are installing a tall card, install it in connector 1. If you are installing two short cards on a model with multiple connectors, use connector 1 first, and then use connector 2.
3 Unpack the card. Save the packaging materials.
4 Align the connection points on the card with the connector on the system board, and push the card firmly into the system board connector.
5 Insert the screw saved from the cover plate (or the extra screw shipped with the card).
6 Tighten the screw to secure the card.

Installing an option card
Screw · Cover plate

Replacing the shield
After you have installed options on the printer system board, follow these steps to reattach the shield and close the doors.
1 Align the keyholes on the shield with the screws on the frame.
2 Slide the shield down onto the screws.
3 Tighten the screws.

4 Close the side door.
5 Close the top front cover.
6 Close the multipurpose feeder.
Replacing the shield

This chapter covers information about sending a job to print, printing confidential jobs, canceling a print job, printing a menu settings page, a font list, and a directory list. This chapter also provides information on printing folio and statement size media. For tips on paper jam prevention and print media storage, see Avoiding jams or Storing print media.
A printer driver is software that lets your computer communicate with the printer. When you choose Print from a software application, a window representing the printer driver opens. You can then select the appropriate settings for the specific job you are sending to the printer. Print settings selected from the driver override the default settings selected from the printer operator panel.
You may need to click Properties or Setup from the initial Print dialog to see all of the available printer settings you can change. If you are not familiar with a feature in the printer driver window, open the online Help for more information.
To support all the printer features, use the Lexmark custom printer drivers supplied with the printer. Updated drivers, as well as a complete description of the driver packages and Lexmark driver support, are available from the Lexmark Web site.
To print a job from a typical Windows application:
1 Open the file you want to print.
2 From the File menu, select Print.
3 Select the correct printer in the dialog. Modify the printer settings as appropriate (such as the pages you want to print or the number of copies).
4 Click Properties or Setup to adjust printer settings that were not available on the first screen, and then click OK.
5 Click OK or Print to send the job to the selected printer.
A USB Direct interface is located on the operator panel so you can insert a USB flash memory device and print PDF documents. Printing a document from a USB flash memory device is similar to printing a held job.
For information regarding tested and approved USB flash memory devices, see our Lexmark Web site at http:// support.lexmark.com, and click KnowledgeBase to search for Direct USB printing.
Printing

To print from a USB flash memory device:
1 Make sure the printer is on and Ready or Busy appears.
2 Insert a USB flash memory device into the USB Direct interface.

3 Press until the appears next to the document you want to print, and then press .
A screen asking the number of copies to be printed will appear.


4 To print only one copy, press , or manually input the number of copies with the number pad, then press .
finished printing.
The document will begin printing.
If you leave the device in the printer after exiting the USB drive menu, you can still print PDFs on the device as held jobs. See Printing confidential and held jobs.
Printing from a USB flash memory device

Canceling a print job
There are several methods for canceling a print job.
– Canceling a job from the taskbar – Canceling a job from the desktop
– Canceling a print job from a computer running Mac OS 9 – Canceling a job from a computer running Mac OS X
If the job is formatting or already printing, and Cancel a Job appears on the first line of the display:
1 Press .
A list of jobs appears.
2 Press until appears next to the job requiring cancelation, and then press .
The message Canceling <filename> appears.
Canceling a job from the taskbar
When you send a job to print, a small printer icon appears in the right corner of the taskbar.
1 Double-click the printer icon.
A list of print jobs appears in the printer window.
2 Select the job you want to cancel.
3 Press the Delete key on the keyboard.
1 Minimize all programs to reveal the desktop.
2 Double-click the My Computer icon.
Settings Æ Control Panel, and then go to step 4.
3 Double-click the Printers icon.
A list of available printers appears.
4 Double-click the printer you selected when you sent the job.
A list of print jobs appears in the printer window.
5 Select the job you want to cancel.
Canceling a print job

6 Press the Delete key on the keyboard.
Canceling a print job from a computer running Mac OS 9
When you send a job to print, the printer icon for your selected printer appears on the desktop.
1 Double-click the printer icon on your desktop.
A list of print jobs appears in the printer window.
2 Select the print job you want to cancel.
3 Click the trash can button.
When you send a job to print, the printer icon for your selected printer appears in the dock.
1 Open Applications Æ Utilities, and then double-click Print Center or Printer Setup.
2 Double-click the printer you are printing to.
3 In the printer window, select the print job you want to cancel.
4 Press Delete.
You can print a menu settings page to review the default printer settings and to verify the printer options are installed correctly.
1 Make sure the printer is on.
2 Press on the operator panel.
3 Press until the appears next to Reports, and then press .
4 Press until the appears next to Menu Settings Page, and then press .
The printer returns to Ready after the page prints.
You can print a network setup page to review the default printer settings and to verify the printer options are installed correctly.
1 Make sure the printer is on.
2 Press on the operator panel.
3 Press until the appears next to Reports, and then press .
4 Press until the appears next to Network Setup Page or Network <x> Setup Page, and then press .
The printer returns to Ready.
Printing the menu settings page

Printing a font sample list
To print samples of the fonts currently available for the printer:
1 Make sure the printer is on and the Ready message appears.
2 Press on the operator panel.
3 Press until the appears next to Reports, and then press .
4 Press until the appears next to Print Fonts, and then press .
5 Press until the appears next to PCL Fonts, PostScript Fonts, or PPDS Fonts, and then press .
The printer returns to Ready.
A directory listing shows the resources stored in flash memory or on the hard disk. To print a listing:
1 Make sure the printer is on and the Ready message appears.
2 Press on the operator panel.
3 Press until the appears next to Reports, and then press .
4 Press until the appears next to Print Directory, and then press .
The printer returns to Ready.
The term held job refers to any type of print job that can be initiated by the user at the printer. This includes a confidential job, a verify print job, a reserve print job, a repeat print job, a bookmark, a profile, or a file on a USB flash memory device. When sending a job to the printer, you can specify in the driver that you want the printer to hold the job in memory. Once your job is stored in printer memory, go to the printer, and use the printer operator panel to specify what you want to do with your print job.
All confidential and held jobs have a user name associated with them. To access confidential or held jobs, you must first select the type of job (confidential or held), and then select your user name from the user name list. Once you select your user name, you can print all your confidential jobs or select an individual print job. You can then choose the number of copies for the print job, or you can delete the print job.
When you send a confidential job to the printer, you must enter a personal identification number (PIN) from the driver. The PIN must be four digits using the numbers 0–9. The job is held in printer memory until you enter the same four-digit PIN from the operator panel and choose to print or delete the job. This ensures the job does not print until you are there to retrieve it. No one else using the printer can print the job without the PIN.
1 From a word processor, spreadsheet, browser, or other application, select File Æ Print.
2 Click Properties. (If there is no Properties button, click Setup, and then click Properties.)
3 Depending on the operating system, you may have to click the Other Options tab, and then click Print and Hold.
Print or Print and Hold, and then follow the driver instructions.
Printing a font sample list
Windows

4 Enter a User Name and PIN.
5 Send your job to the printer.
Go to the printer when you are ready to retrieve your confidential print job, and follow the At the printer steps.
1 From a word processor, spreadsheet, browser, or other application, select File Æ Print.
2 In the Copies & Pages or General pop-up menu, select Job Routing.
a When using Mac OS 9, if Job Routing is not a choice on the pop-up menu, select Plug-in Preferences Æ Print Time Filters.
b Turn down the disclosure triangle to the left of Print Time Filters, and select Job Routing.
c In the pop-up menu, select Job Routing.
3 In the radio group, select Confidential Print.
4 Enter a User Name and PIN.
5 Send your job to the printer.
Go to the printer when you are ready to retrieve your confidential print job, and follow the At the printer steps.
1 Press until the appears next to Held jobs, and then press .
2 Press until the appears next to your user name, and then press .
3 Press until the appears next to Confidential jobs, and then press .
4 Enter your PIN.
For more information, see Entering a personal identification number (PIN).
5 Press until the appears next to the job you want to print, and then press .
After you select your user name and Confidential Job, the Enter PIN screen appears.
1 Use the numeric pad to the right of the display to enter the four-digit PIN associated with your confidential job.
If you enter an invalid PIN, the Invalid PIN screen appears.
Press to reenter the PIN, or press until the appears next to Cancel, and then press .
2 Press until the appears next to the job you want to print, and then press .
Printing confidential and held jobs
Macintosh · At the printer

Printing and deleting held jobs
Held jobs (Verify Print, Reserve Print, or Repeat Print) are printed or deleted from the printer operator panel and do not require a PIN number.
If you send a Verify Print job, the printer prints one copy and holds the remaining copies you requested in printer memory. Use Verify Print to examine the first copy to see if it is satisfactory before printing the remaining copies. Once all copies are printed, the Verify Print job is automatically deleted from printer memory.
If you send a Reserve Print job, the printer does not print the job immediately. It stores the job in memory so you can print the job later. The job is held in memory until you delete it from the Held Jobs menu. Reserve Print jobs may be deleted if the printer requires extra memory to process additional held jobs.
If you send a Repeat Print job, the printer prints all requested copies of the job and stores the job in memory so you can print additional copies later. You can print additional copies as long as the job remains stored in memory.
memory to process additional held jobs.
1 From a word processor, spreadsheet, browser, or other application, select File Æ Print.
2 Click Properties. (If there is no Properties button, click Setup, and then click Properties.)
3 Depending on the operating system, you may have to click the Other Options tab, and then click Print and Hold.
Print and Hold, then follow the driver instructions.
4 Select the type of held job you want, and then send your job to the printer.
Go to the printer when you are ready to retrieve your confidential print job, and follow the At the printer steps.
1 From a word processor, spreadsheet, browser, or other application, select File Æ Print.
2 In the Copies & Pages or General pop-up menu, select Job Routing.
a When using Mac OS 9, if Job Routing is not a choice on the pop-up menu, select Plug-in Preferences Æ Print Time Filters.
b Turn down the disclosure triangle to the left of Print Time Filters, and select Job Routing.
c In the pop-up menu, select Job Routing.
3 In the radio group, select the type of held job you want, enter a user name, and then send your job to the printer.
Go to the printer when you are ready to retrieve your confidential print job, and follow the At the printer steps.
1 Press until the appears next to Held jobs, and then press .
2 Press until the appears next to your user name, and then press .
Printing confidential and held jobs

3 Press until the appears next to the type of action you want to perform, and then press .
Print All Delete All
Print A Job Delete A Job
If you selected Print A Job, Delete A Job, or Print Copies, press until the appears next to the job you want, and then press .
The job will print or be deleted according to the type of print job and action you selected.
Media is paper, card stock, transparencies, labels, and envelopes. The last four are sometimes referred to as specialty media. Follow these instructions to print on specialty media.
1 Load the media as specified for the tray being used. See Loading standard trays and optional trays for help.
2 From the printer operator panel, set the Paper Type and Paper Size according to the media you loaded. See Setting the Paper Type and Paper Size for help.
3 From the computer software application, set the paper type, size, and source according to the media you loaded.
a From a word processor, spreadsheet, browser, or other application, select File Æ Print.
b Click Properties (or Options, Printer, or Setup, depending on the application) to view the printer driver settings.
c Click the Paper tab.
A paper tray list will appear.
d Select the tray containing the specialty media.
e Select the media type (transparencies, envelopes, and so on) from the Paper Type list box.
f Select the size of the specialty media from the Paper Size list box.
g Click OK, and then send the print job as usual.
a Select File Æ Page Setup.
b Select the size of the specialty media from the Paper pop-up menu, and then click OK.
c Select File Æ Print.
d With General selected on the top pop-up menu, go to the Paper Source pop-up menu, and select the tray containing the specialty media or the name of the media.
e Click Print.
a Select File Æ Page Setup.
b Select the printer from the Format for pop-up menu.
c Select the size of the specialty media from the Paper pop-up menu, and then click OK.
Printing on specialty media

d Select File Æ Print.
e On the Copies & Pages pop-up menu, select Imaging.
f Select the specialty media on the Paper Type pop-up menu.
g On the Imaging pop-up menu, select Paper Feed.
h Select the tray containing the specialty media from the All pages from or First page from / Remaining from pop-up menus.
i Click Print.
The printer has a 250-sheet or 500-sheet standard tray, depending on the model you purchased. You may have also purchased one or more 250-sheet or 500-sheet optional trays or a 2000-sheet drawer. The steps for loading a 250-sheet tray or 500-sheet tray are the same.
500-sheet tray.
To load print media:
so may cause a jam.
1 Remove the tray from the printer, and place it on a flat, level surface.
2 Squeeze the side guide tab, and slide the guide to the outer edge of the tray.


Loading standard trays and optional trays

3 Squeeze the rear guide tab, and slide the guide to the correct position for the size media you are loading.
4 Flex the sheets back and forth to loosen them, then fan them. Do not fold or crease the print media. Straighten the edges on a level surface.


Loading standard trays and optional trays
Size indicators

5 Place the print media in the tray:


Loading standard trays and optional trays

6 Squeeze the side guide tab, and slide the guide toward the inside of the tray until it lightly rests against the edge of the media.
7 Insert the tray into the printer.

After setting the Paper Type and Paper Size to the correct values for the type and size used in the trays, then any trays containing the same size and type are automatically linked by the printer.
the Paper Size setting.
To change the Paper Size and Paper Type setting:
1 Make sure the printer is on.
2 Press on the operator panel.
3 Press until the appears next to Paper Menu, and then press .
4 Press until the appears next to Paper Size/Type, and then press .
5 Press until the appears next to the input source you want to use, and then press .
6 Press until the appears next to the paper size you want to use, and then press .
7 Press until the appears next to the paper type you want to use, and then press .
This saves this setting as the new user default, and the printer returns to Ready.
Setting the Paper Type and Paper Size

Loading the multipurpose feeder
The multipurpose feeder can hold several sizes and types of print media, such as transparencies, postcards, note cards, and envelopes. It can be used for single-page or manual printing or as an additional tray.
The multipurpose feeder can hold approximately:
The multipurpose feeder accepts print media within the following dimensions:
The icons on the multipurpose feeder show you how to load the multipurpose feeder with paper, how to turn an envelope for printing, and how to load letterhead paper for simplex and duplex printing. A finisher affects how letterhead documents should be loaded for duplexing. You can print simplex jobs on letterhead (or other preprinted media) that has been loaded specifically for duplex printing by changing the value in the Paper Loading menu.
Loading the multipurpose feeder
Simplex letterhead · Duplex letterhead · Envelope

To load print media:
the operator panel indicator light is blinking. Doing so may cause a jam.
1 Push the release latch, and lower the multipurpose feeder.
2 Pull the tray extension out.
force on it.


3 Slide the width guide to the far right.
4 Flex the sheets or envelopes back and forth to loosen them, then fan them. Do not fold or crease the print media. Straighten the edges on a level surface.
to prevent jams. Be careful not to scratch or leave fingerprints on the transparencies.

Transparencies
Loading the multipurpose feeder

5 Load the media in the tray.
Use the stack height label as a guide for stack height when loading print media.
Loading paper, transparencies, or envelopes
installed.
Never use envelopes with stamps, clasps, snaps, windows, coated linings, or self-stick adhesives. These envelopes may severely damage the printer.
types in the same tray.
Loading the multipurpose feeder

Loading letterhead or preprinted paper
With a finisher attached


Simplex (single sided)


Duplex
Loading the multipurpose feeder

6 Slide the side guide toward the inside of the tray until it lightly rests against the edge of the media.

7 Set the Paper Size and Paper Type for the multipurpose feeder (MP Feeder Size and MP Feeder Type) to the correct value for the print media you loaded.
a Press on the operator panel.
b Press until the appears next to Paper Menu, and then press .
c Press until the appears next to Paper Size/Type, and then press .
d Press until the appears next to MP Feeder Size/Type, and then press .
e Press until the appears next to the media size you loaded, and then press .
f Press until the appears next to MP Feeder Size/Type, and then press .
g Press until the appears next to the media type you loaded, and then press .
The printer returns to Ready.
Closing the multipurpose feeder
1 Remove print media from the multipurpose feeder.
2 Push the extension tray in.
3 Close the multipurpose feeder cover.
Loading the multipurpose feeder

Loading the 2000-sheet drawer
The optional 2000-sheet drawer can be used for plain paper, letterhead or other preprinted paper, labels, or transparencies. For trouble-free printing, make sure you:
you are using. This information is usually on the paper package.
To load the 2000-sheet drawer:
1 Open the loading door. If the elevator tray is not already in the lowered position, push the elevator button to lower the tray.
2 Flex the sheets back and forth to loosen them, then fan them. Do not fold or crease the print media. Straighten the edges on a level surface.
Loading the 2000-sheet drawer
Elevator button

3 Slightly bend the stack of print media as shown, and place it on the elevator tray with the preferred print side facing down. Align the stack of print media to the back of the drawer.
Carefully align each stack as you load it to ensure a smooth edge where the stacks meet. Do not load print media above the load line.
Simplex (single sided)
4 Close the loading door.
Loading the 2000-sheet drawer

Loading the envelope feeder
The optional envelope feeder can accept a variety of envelope sizes. However, the envelope feeder must be adjusted correctly to ensure trouble-free printing. To load the envelope feeder:
1 Adjust the envelope support for the length of envelope you are loading.
2 Lift the envelope weight back toward the printer. It stays in place.


3 Slide the width guide to the far right.
4 Flex a stack of envelopes back and forth, and then straighten the edges on a level surface. Press down the corners to flatten them.
Fan the envelopes. This prevents the edges of the envelopes from sticking together and helps them feed properly.


Loading the envelope feeder

5 Load the stack of envelopes flap side down with the stamp area and the flap on the left. The end of the envelopes with the stamp area enters the envelope feeder first.
Let the envelopes at the bottom of the stack slide into the envelope feeder slightly more than the ones at the top of the stack.
These envelopes may severely damage the printer.
guide for the correct stack height when loading. Do not try to load more envelopes indicated by the stack height label; overloading can cause jams.
6 Slide the width guide to the left until it lightly touches the stack. Make sure the envelopes do not buckle.


7 Lower the envelope weight to touch the stack.

Loading the envelope feeder

8 Set the Paper Size and Paper Type for the envelope feeder (envelope Feeder Size and envelope Feeder Type) to the correct value for the print media you loaded.
a Press on the operator panel.
b Press until the appears next to Paper Menu, and then press .
c Press until the appears next to Paper Size/Type, and then press .
d Press until the appears next to Envelope Feeder Size/Type, and then press .
e Press until the appears next to the envelope size you loaded, and then press .
f Press until the appears next to Envelope Feeder Size/Type, and then press .
g Press until the appears next to the envelope type you loaded, and then press .
The printer returns to Ready.
Tray linking enables the automatic linking feature for trays when you load the same size and type of print media in multiple sources. The printer automatically links the trays; when one tray is empty, print media feeds from the next linked tray.
For example, if you have the same size and type of print media loaded in tray 2 and tray 4, the printer selects print media from tray 2 until it becomes empty, and then the printer automatically feeds print media from the next linked tray—tray 4.
By linking all trays (standard and optional), you effectively create a single source with a capacity of up to 4,100 sheets.
Make sure you load the same size and type of print media in each tray in order to link the trays.
Set the paper size and type for each tray, to set the paper type or size:
1 Press on the operator panel.
2 Press until the appears next to Paper Menu, and then press .
3 Press until the appears next to Paper Size/Type, and then press .
4 Press until the appears next to Tray <x> Size/Type, and then press .
5 Press until the appears next to the paper size you loaded, and then press .
6 Press until the appears next to Tray <x> Size/Type, and then press .
7 Press until the appears next to the paper type you loaded, and then press .
The printer returns to Ready.
To disable tray linking, set the Paper Type to a unique value in each one of the trays. If all the trays do not have the same type of print media when they are linked, you could mistakenly print a job on the wrong paper type.
Linking trays

Identifying and linking output bins
There is one standard output bin on all printer models. Depending on the model you selected, your output bin capacity is 250 or 500 sheets. If you need additional output capacity, there are several optional output bins available for the printer.
If you have multiple output bins, you can link them into a single output source. Linking output bins lets the printer automatically switch output to the next available bin.
The following table provides information on standard and optional output bin capability and connectivity.
Each bin accommodates How many can be installed on the printer
Bin is allowed to connect with Illustration of output bin Print media Printer Models
T640 N/A — one is standard on the printer and located on top of the printer
Any of the options in combinations as follows in this column
500 sheets (75 g/m2) of plain paper 300 transparencies 200 labels • 50 envelopes (75 g/m2)
Finisher Sheets of 75 g/m2 of plain paper (maximum number of stapled jobs is 40) T640 500 sheets T642 750 sheets T644 750 sheets
1 1 output expander or 1 5-bin mailbox*
1 1 output expander*
* See the instructions that came with the option for information on how to install options in relation to each other.
Identifying and linking output bins


Each bin accommodates How many can be installed on the printer
Bin is allowed to connect with Illustration of output bin Print media Printer Models
3 1 5-bin mailbox, 1 high-capacity output stacker, or 1 finisher*
120 sheets (75 g/m2) of plain paper for each of the five bins for a total of 600 for all bins
* See the instructions that came with the option for information on how to install options in relation to each other.
Linking output bins lets you create a single output source so the printer can automatically switch output to the next available bin. You can also set the output type for media such as card stock or envelope sizes that cannot be sent to an optional output bin. For more information on the values available to configure your output bins, see the Menus and Messages Guide.
to the floor to the bin farthest from the floor.
To link output bins:
1 Press on the operator panel.
2 Press until the appears next to Paper Menu, and then press
3 Press until the appears next to Bin Setup, and then press .
4 Press until the appears next to Configure Bins, and then press .
5 Press until the appears next to Link, and then press .
The printer returns to Ready.
Identifying and linking output bins

Print media is paper, card stock, transparencies, labels, and envelopes. The printer provides high quality printing on a variety of print media. You must consider a number of things concerning print media before you print. This chapter provides information to help you make print media selections.
For more details about the types of paper and specialty media the printer supports, see the Card Stock & Label Guide available on our Lexmark Web site at www.lexmark.com.
We recommend that you try a limited sample of any paper or specialty media you are considering using with the printer before purchasing large quantities.
The following tables provide information on standard and optional sources for both input and output trays and bins.
Understanding paper and specialty media guidelines

Legend — indicates support
T642, T644 500-sheet tray
Print media size Dimensions
A4 210 x 297 mm (8.27 x 11.7 in.)
A5 148 x 210 mm (5.83 x 8.27 in.)
JIS B5 182 x 257 mm (7.17 x 10.1 in.)
Letter 215.9 x 279.4 mm (8.5 x 11 in.)
Legal 215.9 x 355.6 mm (8.5 x 14 in.)
Executive 184.2 x 266.7 mm (7.25 x 10.5 in.)
Folio1 216 x 330 mm (8.5 x 13 in.)
Statement1 139.7 x 215.9 mm (5.5 x 8.5 in.)
Universal2 139.7 x 210 mm to 215.9 x 355.6 mm (5.5 x 8.27 in. to 8.5 x 14 in.)
69.85 x 127 mm to 215.9 x 355.6 mm (2.75 x 5 in. to 8.5 x 14 in.)
69.85 x 127 mm to 229 x 355.6 mm (2.75 x 5 in. to 9.01 x 14 in.)
148 x 182 mm to 215.9 x 355.6 mm (5.83 x 7.17 in. to 8.5 x 14 in.)
7 ¾ Envelope 98.4 x 190.5 mm (3.875 x 7.5 in.)
1 This size does not appear in the Paper Size menu until Tray Size Sensing is turned off. See “Printing folio and statement sizes” for more information. 2 This size setting formats the page for 215.9 x 355.6 mm (8.5 x 14 in.) unless the size is specified by the software application.

Legend — indicates support
T642, T644 500-sheet tray
Print media size Dimensions
9 Envelope 98.4 x 225.4 mm (3.875 x 8.87 in.)
10 Envelope 104.8 x 241.3 mm (4.12 x 9.5 in.)
DL Envelope 110 x 220 mm (4.33 x 8.66 in.)
B5 Envelope 176 x 250 mm (6.93 x 9.84 in.)
C5 Envelope 162 x 229 mm (6.38 x 9.01 in.)
Other Envelope1 98.4 x 162 mm to 176 x 250 mm (3.87 x 6.38 in. to 6.93 x 9.84 in.)
98.4 x 162 mm to 229 x 342 mm (3.87 x 6.38 in. to 9.01x 12.76 in.)
1 This size does not appear in the Paper Size menu until Tray Size Sensing is turned off. See “Printing folio and statement sizes” for more information. 2 This size setting formats the page for 215.9 x 355.6 mm (8.5 x 14 in.) unless the size is specified by the software application.

T642, T644
T640
Paper
Card stock
Transparencies
Vinyl labels*
Paper labels*
Polyester label*
Dual-web and integrated labels*
* Printing label applications on the printer requires a special label fuser cleaner. The label fuser cleaner is included with a special label cartridge for label applications. See Ordering supplies for more information on obtaining a label fuser cleaner.

Integrated tray and optional 500-sheet drawer
Multipurpose feeder and optional 250-sheet drawer Envelope feeder
60 to 176 g/m2 grain long (16 to 47 lb bond)
60 to 135 g/m2 grain long (16 to 36 lb bond)
Paper Xerographic or business paper
Card stock— maximum (grain long)1 Index Bristol 163 g/m2 (90 lb) 120 g/m2 (67 lb)
Tag 163 g/m2 (100 lb) 120 g/m2 (74 lb)
Cover 176 g/m2 (65 lb) 135 g/m2 (50 lb)
Card stock— maximum (grain short)1 Index Bristol 199 g/m2 (110 lb) 163 g/m2 (90 lb) n/a
Tag 203 g/m2 (125 lb) 163 g/m2 (100 lb)
Cover 216 g/m2 (80 lb) 176 g/m2 (65 lb)
Transparencies Laser printer 138 to 146 g/m2 (37 to 39 lb bond)
138 to 146 g/m2 (37 to 39 lb bond)
Labels—maximum4 Paper 180 g/m2 (48 lb bond)
163 g/m2 (43 lb bond) Note: Not supported in the multipurpose feeder.
Dual-web paper 180 g/m2 (48 lb bond)
163 g/m2 (43 lb bond) Note: Not supported in the multipurpose feeder.
Polyester 220 g/m2 (59 lb bond)
220 g/m2 (59 lb bond) Note: Not supported in the multipurpose feeder.
Vinyl5 300 g/m2 (92 lb liner)
260 g/m2 (78 lb liner) Note: Not supported in the multipurpose feeder.
1 Grain short is preferred for papers over 135 g/m2. 2 Includes envelopes fed from the multipurpose feeder only. 3 28 lb bond envelopes are limited to 25% cotton content. 4 Printing label applications on the printer requires a special label fuser cleaner. See Ordering supplies for more information on obtaining a fuser cleaner. 5 Information on whether your vinyl label converter has passed Lexmark criteria is available at the Lexmark Web site (www.lexmark.com); search for “converter list.” You can also check the Lexmark Automated Fax system (LEXFAXSM).

Integrated tray and optional 500-sheet drawer
Multipurpose feeder and optional 250-sheet drawer Envelope feeder
140 to 175 g/m2 140 to 175 g/m2
Integrated forms Pressure- sensitive area (must enter the printer first)
Paper base (grain long)
75 to 135 g/m2 (20 to 36 lb bond)
75 to 135 g/m2 (20 to 36 lb bond)
Not recommended 60 to 105 g/m2 (16 to 28 lb bond)2, 3 60 to 105 g/m2 (16 to 28 lb bond)3
Envelopes 100% cotton content maximum weight—24 lb
Sulfite, wood-free, or up to 100% cotton bonds
1 Grain short is preferred for papers over 135 g/m2. 2 Includes envelopes fed from the multipurpose feeder only. 3 28 lb bond envelopes are limited to 25% cotton content. 4 Printing label applications on the printer requires a special label fuser cleaner. See Ordering supplies for more information on obtaining a fuser cleaner. 5 Information on whether your vinyl label converter has passed Lexmark criteria is available at the Lexmark Web site (www.lexmark.com); search for “converter list.” You can also check the Lexmark Automated Fax system (LEXFAXSM).
Print media weight—optional output bins
High-capacity output stacker Finisher
Print media Type 5-bin mailbox Output expander
See separate Finisher media weight table. Card stock— maximum (grain long)
Xerographic or business paper
60 to 90 g/m2 (16 to 24 lb bond)
60 to 176 g/m2 (16 to 47 lb bond)
60 to 176 g/m2 (16 to 47 lb bond)
163 g/m2 (90 lb) 163 g/m2 (90 lb)
Index Bristol Not recommended
Tag 163 g/m2 (100 lb) 163 g/m2 (100 lb)
Cover 176 g/m2 (65 lb) 176 g/m2 (65 lb)
Index Bristol 199 g/m2 (110 lb) 199 g/m2 (110 lb)
Card stock— maximum (grain short)
Tag 203 g/m2 (125 lb) 203 g/m2 (125 lb)
Cover 216 g/m2 (80 lb) 216 g/m2 (80 lb)
Transparencies Laser printer 138 to 146 g/m2 (37 to 39 lb bond)
138 to 146 g/m2 (37 to 39 lb bond)

Print media weight—optional output bins
High-capacity output stacker Finisher
Print media Type 5-bin mailbox Output expander
See separate Finisher media weight table. Dual-web paper
180 g/m2 (48 lb bond)
180 g/m2 (48 lb bond)
180 g/m2 (48 lb bond)
180 g/m2 (48 lb bond)
Polyester 220 g/m2 (59 lb bond)
220 g/m2 (59 lb bond)
Vinyl 300 g/m2 (92 lb liner)
300 g/m2 (92 lb liner)
Integrated forms Pressure sensitive area (must enter the printer first)
140 to 175 g/m2 (up to 47 lb bond)
140 to 175 g/m2 (up to 47 lb bond)
See separate Finisher media weight table.
75 to 135 g/m2 (20 to 36 lb bond)
75 to 135 g/m2 (20 to 36 lb bond)
Paper base (grain long)
Envelopes Sulfite, wood- free or up to 100% cotton bond
60 to 105 g/m2 (16 to 28 lb bond)
60 to 105 g/m2 (16 to 28 lb bond)
Size Standard1 Offset Stapled
A4 210 x 297 mm (8.27 x 11.7 in.)
A5 148 x 210 mm (5.83 x 8.27 in.)
JIS B5 182 x 257 mm (7.17 x 10.1 in.)
Letter 215.9 x 279.4 mm (8.5 x 11 in.)
Legal 215.9 x 355.6 mm (8.5 x 14 in.)
Executive 184.2 x 266.7 mm (7.25 x 10.5 in.)
Folio2 216 x 330 mm (8.5 x 13 in.)
Statement2 139.7 x 215.9 mm (5.5 x 8.5 in.)
1 Paper passes to the finisher bin without being stapled or offset. 2 This size does not appear in the Paper Size menu until Tray Size Sensing is turned off. See Printing folio and statement sizes for more information.

Size Standard1 Offset Stapled
7 ¾ Envelope 98.4 x 190.5 mm (3.875 x 7.5 in.)
9 Envelope 98.4 x 225.4 mm (3.875 x 8.9 in.)
10 Envelope 104.8 x 241.3 mm (4.12 x 9.5 in.)
DL Envelope 110 x 220 mm (4.33 x 8.66 in.)
C5 Envelope 162 x 229 mm (6.38 x 9.01 in.)
B5 Envelope 176 x 250 mm (6.93 x 9.84 in.)
Other Envelope 98.4 x 162 mm to 176 x 250 mm (3.87 x 6.38 in. to 6.93 x 9.84 in.)
98.4 x 162 mm to 229 x 342 mm (3.87 x 6.38 in. to 9.01x 12.76 in.)
1 Paper passes to the finisher bin without being stapled or offset. 2 This size does not appear in the Paper Size menu until Tray Size Sensing is turned off. See Printing folio and statement sizes for more information.
Standard* Offset Stapled
60 to 176 g/m2 (16 to 47 lb bond)
60 to 90 g/m2 (16 to 24 lb bond)
60 to 90 g/m2 (16 to 24 lb bond)
Paper Xerographic or business paper
Card stock— maximum (grain long)
Index Bristol 163 g/m2 (90 lb bond)
Not recommended Not recommended
Tag 163 g/m2 (100 lb bond)
Index Bristol 199 g/m2 (110 lb bond)
Card stock— maximum (grain short)
Not recommended Not recommended
Tag 203 g/m2 (125 lb bond)
Cover 216 g/m2 (80 lb bond)
* Paper passes to the finisher bin without being stapled or jogged.

Standard* Offset Stapled
Transparencies Laser printer 138 to 146 g/m2 (37 to 39 lb bond)
138 to 146 g/m2 37 to 39 lb bond) Not recommended
140 to 175 g/m2 (up to 47 lb bond)
Integrated forms Pressure sensitive area
Not recommended Not recommended
75 to 135 g/m2 (20 to 36 lb bond)
Paper base (grain long)
Labels — upper limit
Paper 180 g/m2 (48 lb bond)
Not recommended Not recommended
Dual-web paper 180 g/m2 (48 lb bond)
Polyester 220 g/m2 (59 lb bond)
Vinyl 300 g/m2 (92 lb bond)
60 to 105 g/m2 (16 to 28 lb bond)
Envelopes Sulfite, wood-free, or up to 100% cotton bond
Not recommended Not recommended
* Paper passes to the finisher bin without being stapled or jogged.
Finisher media weight · Print media Type · Supported print media

Selecting print media
Selecting the appropriate print media for the printer helps you avoid printing problems. The following sections contain guidelines for choosing the correct print media for the printer.
For the best print quality, use 75 g/m2 (20 lb) xerographic, grain long paper. Try a sample of any paper you are considering using with the printer before buying large quantities.
When loading paper, note the recommended print side on the paper package, and load paper accordingly. See Loading standard trays and optional trays, Loading the multipurpose feeder, or Loading the 2000-sheet drawer for detailed tray-loading instructions.
The following paper characteristics affect print quality and reliability. We recommend that you follow these guidelines when evaluating new paper stock.
For detailed information, see the Card Stock & Label Guide located on the Lexmark Web site at www.lexmark.com.
The laser printing process heats paper to high temperatures of 230°C (446°F). For Magnetic Ink Character Recognition (MICR) applications and for non-MICR applications, use only paper able to withstand these temperatures without discoloring, bleeding, or releasing hazardous emissions. Check with the manufacturer or vendor to determine whether the paper you have chosen is acceptable for laser printers.
The printer can automatically feed paper weights from 60 to 176 g/m2 (16 to 47 lb bond) grain long in the integrated and optional 500-sheet trays and paper weights from 60 to 135 g/m2 (16 to 36 lb bond) grain long in the multipurpose feeder and optional 250-sheet trays. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 75 g/m2 (20 lb bond) grain long paper. When using paper narrower than 182 x 257 mm (7.2 x 10.1 in.), make sure the weight is greater than or equal to 90 g/m2 (24 lb bond).
The following papers are not recommended for use with the printer:
In some cases, you can adjust registration with your software application to successfully print on these forms.
Weight · Selecting print media

You can feed transparencies from the standard tray (250-sheet tray for the T640 or 500-sheet tray for the T642 and T644), optional 250- or 500-sheet trays, or the multipurpose feeder. Try a sample of any transparencies you are considering using with the printer before buying large quantities.
When printing on transparencies:
The printer can print directly on transparencies designed for use in laser printers. Print quality and durability depend on the transparency used. Always print samples on the transparencies you are considering before buying large quantities.
The Paper Type setting should be set to Transparency to help prevent jams. Check with the manufacturer or vendor to determine whether your transparencies are compatible with laser printers that heat transparencies to 230°C (446°F). Use only transparencies that are able to withstand these temperatures without melting, discoloring, offsetting, or releasing hazardous emissions. For detailed information, see the Card Stock & Label Guide, which is available on the Lexmark Web site at www.lexmark.com.
Transparencies can be fed automatically from the multipurpose feeder and all standard and optional trays, except the 2000- sheet drawer. See Identifying and linking output bins for information about transparency compatibility with optional output bins.
Be careful when you handle transparencies. Fingerprints on the surface of the transparency cause poor print quality.
You can load up to 10 envelopes in the multipurpose feeder and 85 envelopes in the envelope feeder. Try a sample of any envelopes you are considering using with the printer before buying large quantities. See Loading the multipurpose feeder and Loading the envelope feeder for instructions on loading envelopes.
When printing on envelopes:
Selecting print media

The printer can print on many labels designed for use with laser printers. These labels are supplied in letter size, A4 size, and legal size sheets. Label adhesives, face sheet (printable stock), and topcoats must be able to withstand temperatures of 230°C (446°F) and pressure of 25 pounds per square inch (psi).
Try a sample of any labels you are considering using with the printer before purchasing a large quantity.
For detailed information on label printing, characteristics, and design, see the Card Stock & Label Guide available on the Lexmark Web site at www.lexmark.com/publications.
fuser cleaner for label applications to optimize feed reliability. See Ordering supplies for information on obtaining a label fuser cleaner.
After printing approximately 10,000 pages of labels (or each time you replace the print cartridge), complete the following steps to maintain printer feeding reliability:
1 Print five sheets of paper.
2 Wait approximately five seconds.
3 Print five more sheets of paper.
When printing on labels:
Selecting print media

Card stock is single ply, and has a large array of properties, such as the moisture content, thickness, and texture, that can significantly affect print quality. See Supported print media for information on the preferred weight and for the grain direction of print media.
Try a sample of any card stock you are considering using with the printer before purchasing a large quantity.
After printing approximately 10,000 pages of card stock (or each time you replace the print cartridge), complete the following steps to maintain printer feeding reliability:
1 Print five sheets of paper.
2 Wait approximately five seconds.
3 Print five more sheets of paper.
When printing on card stock:
Use the following guidelines to avoid paper feeding problems and uneven print quality.
Storing print media

Avoiding jams
Use appropriate print media (paper, transparencies, labels, and card stock) to help ensure trouble-free printing. See Supported print media for more information.
large quantities.
By selecting the appropriate print media and loading it properly, you can avoid most jams. See Loading standard trays and optional trays, Loading the multipurpose feeder, or Loading the 2000-sheet drawer for detailed tray-loading instructions.
The following hints can help you avoid jams:
Avoiding jams

Periodically, you need to complete certain tasks to maintain optimum print quality. These tasks are covered in this chapter.
If several people are using the printer, you may want to designate a key operator to do the setup and maintenance of the printer. Refer printing problems and maintenance tasks to this key operator.
In the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark Authorized Supplies Dealers in your area. In other countries or regions, visit the Lexmark Web site at www.lexmark.com or contact the place where you bought the printer.
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packaging until you are ready to use them.
Do not expose supplies to:
Maintaining the printer

Determining the status of supplies
The printer operator panel alerts you once a supply item or maintenance is required. You can also view the status of supplies in the printer on the operator panel unless the printer is printing or in a busy state. The header or gray area at the top of the display will indicate the printer is Ready and lets you know if any trays are low. Selecting Status / Supplies on the display will open the Status / Supplies screen where you can view the status of the various trays and open the View Supplies screen to view the current status of your print cartridge.
Status / Supplies Held jobs
View supplies Ready Tray 1 Low
View Supplies
Toner Low Staples OK
Conserving supplies
Several settings in your application software or on the display let you conserve toner and paper. For more information on changing these settings, see the Menus and Messages Guide on the publications CD.
Supply Menu selection item What the setting does
Toner Toner Darkness in the Settings Æ Quality Menu
Lets you adjust the level of toner released on a sheet of print media. The values range from 1 (lightest setting) to 10 (darkest setting). Note: When toner is low, firmly shake the cartridge to redistribute any remaining toner. See Ordering a print cartridge for more information.
Print media Multipage Print in the Settings Æ Finishing Menu
Causes the printer to print two or more page images on one side of a sheet. Values for Multipage Print are 2 Up, 3 Up, 4 Up, 6 Up, 9 Up, 12 Up, and 16 Up. Combined with the duplex setting, Multipage Print lets you print up to 32 pages on one sheet of paper (16 images on the front and 16 on the back).
Duplex in the Settings Æ Finishing Menu
Duplex printing is available when you install an optional duplex unit. It lets you print on both sides of a sheet of paper.
Use your software application or printer driver to send a Verify Print job.
Lets you examine the first copy of a multiple-copy job to be sure it is satisfactory before you print the other copies. If the job is unsatisfactory, you can cancel the job. See Printing and deleting held jobs for more information about a Verify Print job.
Determining the status of supplies

Ordering supplies
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark Authorized Supplies Dealers in your area. In other countries or regions, visit the Lexmark Web site at www.lexmark.com, or contact the place where you bought the printer.
When the 88 Toner is message appears or when you experience faded print, remove the toner cartridge. Firmly shake it side-to-side and front-to-back several times to redistribute the toner, then reinsert it and continue printing. Repeat this procedure multiple times until the print remains faded. When the print remains faded replace the print cartridge.

Have a new cartridge available when the current one no longer prints satisfactorily.
The recommended print cartridges specifically designed for the printer are:

Part number Description Average cartridge yield1 T640 T642 T644
64015SA Return Program Print Cartridge 6,000 standard pages X X X
64004HA High Yield Return Program Print Cartridge for Label Applications
64404XA Extra High Yield Return Program Print Cartridge for Label Applications
64035SA Print Cartridge 6,000 standard pages X X X
64035HA High Yield Print Cartridge 21,000 standard pages X X X
64435XA Extra High Yield Print Cartridge 32,000 standard pages X
64016SE Return Program Print Cartridge 6,000 standard pages X X X
1 Declared yield value in accordance with ISO/IEC 19752. 2 Designed for use only in the Americas. 3 Designed for use only in Europe, Middle East, and Africa. 4 Designed for use only in Asia Pacific Region, Australia, and New Zealand.
Ordering supplies

Part number Description Average cartridge yield1 T640 T642 T644
64016HE High Yield Return Program Print Cartridge
21,000 standard pages X X X
64416XE Extra High Yield Return Program Print Cartridge
32,000 standard pages X
64004HE High Yield Return Program Print Cartridge for Label Applications
21,000 standard pages X X X
Other available print cartridges
64036SE Print Cartridge 6,000 standard pages X X X
64036HE High Yield Print Cartridge 21,000 standard pages X X X
64436XE Extra High Yield Print Cartridge 32,000 standard pages X
For the Asia Pacific Region4
64017SR Return Program Print Cartridge 6,000 standard pages X X X
64017HR High Yield Return Program Print Cartridge
21,000 standard pages X X X
64417XR Extra High Yield Return Program Print Cartridge
32,000 standard pages X
64004HR High Yield Return Program Print Cartridge for Label Applications
21,000 standard pages X X X
64404XR Extra High Yield Return Program Print Cartridge for Label Applications
32,000 standard pages X
Other available print cartridges
64037SR Print Cartridge 6,000 standard pages X X X
64037HR High Yield Print Cartridge 21,000 standard pages X X X
64437XR Extra High Yield Print Cartridge 32,000 standard pages X
1 Declared yield value in accordance with ISO/IEC 19752. 2 Designed for use only in the Americas. 3 Designed for use only in Europe, Middle East, and Africa. 4 Designed for use only in Asia Pacific Region, Australia, and New Zealand.
You can use the packing material from the new cartridge to ship the old cartridge back to Lexmark for recycling. See Recycling Lexmark products for more information.
80 Scheduled maintenance advised appears on the display after 300,000 pages have printed to let you know it is time to replace printer maintenance items. Order a maintenance kit when 80 Scheduled maintenance advised first appears on the display. The maintenance kit contains all the items necessary to replace the pick rollers, the charge roll, transfer roller, and the fuser.
the charge roll, transfer roller, and pick rollers are contained within the maintenance kit, they should also be individually ordered and replaced as necessary.
Ordering supplies

See the following table for the maintenance kit part number for your specific printer.
Maintenance kit for Part numbers
T640, T642, and T644 40X0102 (100 V) 40X0100 (110 V) 40X0101 (220 V)
Replacement of the fuser must be performed by an authorized service technician.
For finisher maintenance information, see the StapleSmart™ Reference that came with your finisher.
We recommend ordering new charge rolls when toner fog or background shading appears on printed pages. Order Lexmark part number 40X0127.
Order Lexmark part number 40X0130.
Order Lexmark part number 40X0070.Order new pick rolls when the paper fails to properly feed from the tray.
When ordering pick rollers, you need one set per input tray excluding the multipurpose feeder.
A special label fuser cleaner should be used for label applications to optimize feeding reliability. To order this item, visit our Web site at www.lexmark.com or contact your Lexmark representative.
Label fuser cleaners are not recommended for duplex printing.
Staple cartridges hold 3,000 staples. Use part number 11K3188 to order a pack of three staple cartridges. For information on clearing a staple jam, see
When Staples Low or Staples Empty appears on the operator panel display, insert a new staple cartridge in the finisher. See the illustrations inside the stapler access door for more information.
If Staple Alarm is set to Single or Continuous, the alarm is sounded, the printer stops printing, and the Load staples message appears. Install a new staple cartridge, or press to clear the message and continue printing.
To return Lexmark products to Lexmark for recycling:
1 Visit our Web site:
Recycling Lexmark products

2 Follow the instructions on the computer screen.
Follow these guidelines to move the printer within the office or to prepare the printer for shipment.
The printer can be safely moved from one location within an office to another following these precautions:
To transport the printer by vehicle or by commercial carrier, the printer must be repackaged for shipment using the proper packaging. The printer package must be securely fastened to its pallet. Do not use a shipping or transport method that requires the printer to be shipped without a pallet. The printer must stay upright throughout the shipment. If you do not have all the original packaging, contact your local service representative to order the repackaging kit. Additional instructions for repackaging the printer are provided in the repackaging kit.
Moving the printer

By carefully selecting print media and loading it properly, you should be able to avoid most paper jams. For more information on avoiding paper jams, see Avoiding jams. If jams do occur, follow the steps outlined in this section.
To resolve the paper jam messages, you must clear the entire paper path and then press to clear the message and resume printing. The printer prints a new copy of the page that jammed if Jam Recovery is set to On or Auto; however, the Auto setting does not guarantee the page will print.
If the printer jams, the appropriate jam message will be displayed on the printer operator panel. If you select Show areas on the operator panel, you can view one or more images to help you clear the jam.
Show areas Show duplex Show rear door
Continue Show areas
See the diagram on page 81 for an overview of the paper path and areas where jams may occur. The path varies depending on the paper source and output bins.
Clearing jams

Access doors and trays
The following illustration shows the path that print media travels through the printer. The path varies depending on the input source (trays, multipurpose feeder, envelope feeder) and output bins (finisher, stacker, expander, mailbox) you are using.
The numbers in following illustration indicate the numbers that can appear on the operator panel and designate the general area of a paper jam.


27x Paper Jam 28x Paper Jam
Path and locations
Access doors and trays

Understanding jam messages
The following table lists the jam messages that can occur and the action necessary to clear the message. The jam message indicates the area where the jam occurred. However, it is best to clear the entire paper path to ensure you have cleared all possible jams.
Message What to do*
200 and 201 Paper Jam Remove Cartridge
Open the top front cover, remove the print cartridge, and remove the jam.
202 Paper Jam Open Rear Door Open the rear door on the printer, and remove the jam.
23x Paper Jam Check Duplex Remove the duplex tray from the duplex unit, raise duplex deflector, and remove the jam. Open rear duplex door, and remove the jam.
24x Paper Jam Check Tray <x> Open each tray, and remove any jammed media.
250 Paper Jam Check MP Feeder Remove all media from the multipurpose feeder, flex and stack the media, reload the multipurpose feeder, and adjust the guide.
260 Paper Jam Check Env Feeder Lift the envelope weight, remove all envelopes, flex and stack the envelopes, reload the envelope feeder, and adjust the guide.
27x Paper Jam Check Bin x Open the output bin rear doors and then remove the jam.
28x Paper Jam Check Finisher Open the finisher top cover and then remove the jam. Open the finisher rear door, then remove the jam.
28x Staple Jam Open the stapler door, remove the staple holder, remove the staple sheet, clear the jam, reinsert the staples and staple holder, and then close the stapler door.
* After clearing the jam, press to resume printing.
Although there are several places a jam can occur, clearing the paper path is fairly easy depending on the jam message or messages displayed on the operator panel.
Paper jams can occur in three areas: the front of the printer, inside the printer, and at the rear of the printer. Jams in the front of the printer occur in the input options or the duplex tray. Jams inside the printer occur in two locations and require the removal of the print cartridge. Jams can also occur at the rear of the printer or in one of the output options.
been grouped to help you quickly clear the print path. To go to a specific jam, see Understanding jam messages.
Understanding jam messages

1 Remove the paper from the multipurpose feeder.
2 Flex, fan, and restack the media, and place it into the multipurpose feeder.
3 Load the print media.
4 Slide the side guide toward the inside of the tray until it lightly rests against the edge of the media.
5 Press .

The envelope feeder feeds envelopes from the bottom of the stack; the bottom envelope will be the one that is jammed.
1 Lift the envelope weight.
2 Remove all envelopes.
If the jammed envelope has entered the printer and cannot be pulled out, remove the envelope feeder.
a Lift the envelope feeder up out of the printer, and then set it aside.
b Remove the envelope from the printer.
Paper Jam Remove Cartridge for more information.
c Reinstall the envelope feeder. Make sure it snaps into place.
Clearing printer jams

3 Flex and stack the envelopes.


4 Load the envelope feeder.
5 Adjust the guide.
6 Lower the envelope weight.
7 Press .


Clearing printer jams

Paper jams in these areas can occur on the incline surface of a tray or across more than one tray. To clear these areas:
1 Open the printer paper tray, and remove any jammed media.

2 Open the duplex tray.
To remove the media, pull up.


Clearing printer jams

3 Open any optional trays beginning at the top, and remove any jammed media.
Pull the print media either up or down. If it does not pull easily one way, try the other way.


4 If you have an optional 2000-sheet feeder, open the front door, press the elevator button to lower the tray, remove the jam, and make sure the stack of print media is neat and aligned.

5 Press .
Elevator button · Clearing printer jams

1 Push the release latch, and lower the multipurpose feeder.
2 Push the release latch, and open the top front cover.
components.


3 Lift and pull the print cartridge out of the printer.
whenever you are holding the cartridge.
4 Place the print cartridge aside.


Clearing printer jams

5 Pull the print media up and toward you.
the printer.
media from the printer rear door.


6 Align and reinstall the toner cartridge.
7 Close the top front cover.
8 Close the multipurpose feeder.
9 Press .


Clearing printer jams

1 If the paper is exiting the printer, pull the media straight out, and press . Otherwise, continue with step 2.
2 Open the printer rear door.
components.


the printer.
3 Remove the jammed media.
4 Close the rear door.
5 Press .


Clearing printer jams

1 Open the duplex rear door.

2 Remove the jammed media.
Depending on the media location, pull the media either up or down.


Clearing printer jams

3 Close the duplex rear door. Make sure it snaps into place.
4 Press .

Paper jams in this group have been divided into 27x and 28x groups. If you have an output expander, high-capacity output stacker, or the 5-bin mailbox, see 27x Paper Jam Check Bin x. If you have a finisher, see 28x Paper Jam Check Finisher.
To clear a jam in the output expander, high-capacity output stacker, or the 5-bin mailbox:
1 If the paper is exiting into the bin or finisher, pull the media straight out, and press . Otherwise, continue with step 2.
2 Push the output bin rear door latches in toward the center. The rear doors will open and drop down.


Clearing printer jams

3 Remove the jammed media.
4 Close the output bin rear doors, and make sure all doors are secure.
5 Press .


To clear a jam in the finisher:
1 Push the finisher rear door latches in toward the center. The rear door will open and drop down.
2 Remove the jammed media.
3 Close the rear door, and make sure the door is secure.


Clearing printer jams

4 Lift the front edge of the finisher output bin cover until it locks into position.
5 Remove the stack of print media.
6 Close the finisher output bin cover.
7 Press .


A 28x Stapler Jam message indicates staples are jammed in the stapler. This requires removing the staple cartridge holder from the printer.
1 Lift the front edge of the finisher output bin cover until it locks into position.
2 Remove the print media.


3 Press the latch to open the stapler access door.
4 Firmly pull the colored tab to remove the staple cartridge holder from the stapler.


5 Use the metal tab to lift the staple guard, and then pull out the sheet of staples.
Discard the entire sheet.
6 Remove any loose staples from the staple guard.
7 Look through the clear covering on the bottom of the cartridge holder to make sure no staples are jammed in the entry throat.
8 Press down on the staple guard until it snaps securely into place.


Clearing staple jams

9 Push the cartridge holder firmly into the stapler until the cartridge holder clicks into place.
10 Close the stapler access door.
11 Close the finisher output bin cover.

Clearing staple jams

Adjusting operator panel brightness and contrast
If you are having trouble reading your operator panel display, the LCD contrast and brightness can be adjusted through the utilities menu.
The LCD Brightness and LCD Contrast settings are adjusted separately. To change the LCD Brightness or LCD Contrast settings:
1 Make sure the printer is on.
2 Press on the operator panel.
3 Press until the appears next to Settings, and then press .
4 Press until the appears next to Utilities Menu, and then press .
5 Press until the appears next to the LCD setting you want to change, and then press .
6 Press to increase the brightness or contrast, or press to decrease the brightness or contrast.
7 When the adjustment is complete, press .
This saves this setting as the new user default, and the printer returns to Ready.
Since many people could be using the printer, an administrator may choose to lock the operator panel menus to keep others from changing menu settings from the operator panel.
To disable the operator panel menus so that changes cannot be made to the printer default settings:
1 Turn the printer off.
2 Press and hold and while turning the printer on.
3 Release the buttons when you see a clock.
CONFIG MENU appears on the first line of the display.
4 Press until the appears next to Panel Menus, and then press .
5 Press until the appears next to Disable, and then press .
The following messages appear briefly: Submitting selection and Disabling Menus.
The operator panel returns to Panel Menus.
6 Press until the appears next to Exit Config Menus, and then press .
Activating Menu Changes appears. The menus are disabled, and the printer returns to Ready.
Administrative support

Enabling operator panel menus
1 Turn the printer off.
2 Press and hold and while turning the printer on.
3 Release the buttons when you see a clock.
CONFIG MENU appears on the first line of the display.
4 Press until the appears next to Panel Menus, and then press .
5 Press until the appears next to Enable, and then press .
The following messages appear briefly in succession: Submitting selection and Enabling Menus.
The operator panel returns to Panel Menus.
6 Press until the appears next to Exit Config Menus., and then press .
Activating Menu Changes appears. The menus are enabled, and the printer returns to Ready.
When you first enter the printer menus from the operator panel, you may notice an asterisk (*) to the left of a value in the menus. This asterisk indicates the factory default setting. These settings are the original printer settings. (Factory defaults may vary for different regions.)
When you select a new setting from the operator panel, Submitting Selection appears. When the Submitting Selection message disappears, an asterisk appears next to the setting to identify it as the current user default setting. These settings are active until new ones are stored or the factory defaults are restored.
To restore the original printer factory default settings:
(Resources residing in flash memory or on the optional hard disk remain unaffected.)
1 Make sure the printer is on and Ready appears on the display.
2 Press on the operator panel.
3 Press until the appears next to Settings, and then press .
4 Press until the appears next to Setup Menu, and then press .
5 Press until the appears next to Factory Defaults, and then press .
6 Press until the appears next to Restore Now, and then press .
The message Restoring Factory Defaults appears, followed by the Ready message.
When you select Restore:
– The operator panel Display Language setting in the Setup menu. – All settings in the Parallel menu, Serial menu, Network menu, and USB menu.
Enabling operator panel menus

Adjusting Power Saver
To adjust the Power Saver setting:
1 Make sure the printer is on and Ready appears on the display.
2 Press on the operator panel.
3 Press until the appears next to Settings, and then press .
4 Press until the appears next to Setup Menu, and then press .
5 Press until the appears next to Power Saver, and then press .
6 Using the numeric pad or the right and left arrows on the operator panel, enter the number of minutes for the printer to wait before entering Power Saver.
The settings available range from 1–240 minutes. If you want to turn Power Saver off, see Disabling Power Saver.
7 Press .
Submitting Selection appears.
more information, see the Technical Reference available on our Lexmark Web site at www.lexmark.com.
Disabling Power Saver is two step process. First, you must turn the variable on, then select the variable. To disable Power Saver:
1 Turn the printer off.
2 Press and hold and while turning the printer on.
3 Release the buttons when you see a clock.
CONFIG MENU appears on the first line of the display.
4 Press until the appears next to Energy Conserve, and then press .
5 Press until the appears next to Off.
Submitting Selection appears.
The operator panel returns to Energy Conserve.
6 Press until the appears next to Exit Config Menus, and then press .
Resetting the Printer appears briefly followed by a clock. The operator panel then returns to Ready.
7 Make sure Ready appears.
8 Press on the operator panel.
9 Press until the appears next to Settings, and then press .
10 Press until the appears next to Setup Menu, and then press .
11 Press until the appears next to Power Saver, and then press .
12 Use either the numeric keypad or the up and down arrows to enter 0 (zero). After Disabled appears, press .
Submitting Selection appears. Power Saver is now disabled.
Adjusting Power Saver

Encrypting the disk
unaffected.)
1 Turn the printer off.
2 Press and hold and while turning the printer on.
3 Release the buttons when you see a clock.
CONFIG MENU appears on the first line of the display.
4 Press until the appears next to Disk Encryption, and then press .
5 Press until the appears next to Enable, and then press .
6 Contents will be lost. Continue? appears. Press until the appears next to Yes, and then press .
The Encrypting Disk progress bar appears.
7 When disk encryption has finished, press .
8 Press until the appears next to Exit Config Menus, and then press .
To disable disk encryption:
1 Turn the printer off.
2 Press and hold and while turning the printer on.
3 Release the buttons when you see a clock.
CONFIG MENU appears on the first line of the display.
4 Press until the appears next to Disk Encryption, and then press .
5 Press until the appears next to Disable, and then press .
6 Contents will be lost. Continue? appears. Press until the appears next to Yes.
7 Press . The Encrypting Disk progress bar appears.
8 When disk encryption has finished, click the back arrow.
9 Press until the appears next to Exit Config Menu, and then press .
You can enhance the security of network communications and device configuration by using the advanced security options. These features are available through the Web page of the device.
Setting the system password protects configuration of the Embedded Web Server. A system password is also required for Secure mode and confidential communication with MVP.
To set the system password:
1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http: //ip_address/.
2 Click Configuration.
Encrypting the disk

3 Under Other Settings, click Security.
4 Click Create Password if one has not been set previously. If a password has been set before, click Change or Remove Password.
The SSL (Secure Sockets Layer) allows for secure connections to the Web server within the print device. You can connect to the Embedded Web Server more securely by connecting to the SSL port instead of the default HTTP port. The SSL port connection will encrypt all Web server network communications between the PC and the printer. To connect to the SSL port:
Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: https: //ip_address/.
SNMPv3 protocol allows for encrypted and authenticated network communications. It also lets the administrator select a desired level of security. Prior to use, at least one user name and password must be established from the settings page. To configure for SNMPv3 through the Embedded Web Server of the printer:
1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.
2 Click Configuration.
3 Under Other Settings, click Network/Ports.
4 Click SNMP.
SNMPv3 authentication and encryption has three levels of support:
IP Security protocol provides authentication and encryption of communications at the network layer allowing all application and network communications over the IP protocol to be secure. IPSec can be set up between the printer and up to five hosts, using both IPv4 and IPv6. To configure IPSec through the Embedded Web Server:
1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/
2 Click Configuration.
3 Under Other Settings, click Network/Ports.
4 Click IPSec.
Two types of authentication are supported for IPSec:
Setting security using the Embedded Web Server (EWS)

certificate and the certificate authority certificate must be installed. Each host must have its identifier in the Subject Alternate Name of the signed certificate.
place.
You can configure the TCP and UDP ports to one of three modes:
Unsecure will be open.
To configure the Secure mode for TCP and UDP ports from the Embedded Web Server:
1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.
2 Click Configuration.
3 Under Other Settings, click Network/Ports.
4 Click TCP/IP Port Access.
802.1x port authentication allows the printer to join networks that require authentication before allowing access. 802.1x port authentication can be used with the WPA (Wi-Fi Protected Access) feature of an optional internal wireless print server to provide WPA-Enterprise security support.
Support for 802.1x requires the establishment of credentials for the printer. The printer must be known to the Authentication Server (AS). The AS will allow network access to devices presenting a valid set of credentials which typically involves a name/password combination and possibly a certificate. The AS will allow network access to printers presenting a valid set of credentials. You can manage the credentials by using the Embedded Web Server of the printer. To use certificates as part of the credentials:
1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.
2 Click Configuration.
3 Under Other Settings, click Network/Ports.
4 Click Certificate Management.
To enable and configure 802.1x on the Embedded Web Server after installing the required certificates:
1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.
2 Click Configuration.
3 Under Other Settings, click Network/Ports.
Setting security using the Embedded Web Server (EWS)

4 Click 802.1x Authentication.
Authentication.
Operator Panel Menu Lockout lets you create a PIN number and choose specific menus to lock. Each time a locked menu is selected, the user will be prompted to enter the correct PIN at the operator panel. The PIN does not affect any access through the EWS. To lock operator panel menus:
1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.
2 Click Configuration.
3 Under Other Settings, click Security.
4 Click Menu Lockout Setup.
Printing Lockout lets you lock or unlock a printer using an assigned PIN. When locked, every job the printer receives will buffer to the hard disk. A user can print jobs only by entering the correct PIN on the operator panel. You can assign a PIN through the Web page of the device.
can be retrieved from a locked printer.
To set Printing Lockout:
1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.
2 Click Configuration.
3 Under Other Settings, click Security.
4 Click Printer Lockout PIN.
Confidential Print Setup lets you designate a maximum number of PIN entry attempts and set an expiration time for print jobs. When a user exceeds a specific number of PIN entry attempts, all of that user’s print jobs are deleted. When a user has not printed their jobs within a designated time period, the print jobs are deleted. To activate Confidential Print Setup:
1 Open your Web browser. In the address line, enter the IP address of the printer you want to configure using the format: http://ip_address/.
2 Click Configuration.
3 Under Other Settings, click Security.
4 Click Confidential Print Setup.
Setting security using the Embedded Web Server (EWS)

Understanding printer messages
The printer displays three types of messages: status messages, attendance messages, and service messages. Status messages provide information about the current state of the printer. They require no action on your part. Attendance messages alert you to printer problems that require your intervention. Service messages also alert you to problems that require intervention. However the printer will stop printing and the errors are non-recoverable. It may be possible to power the printer off and back on to temporarily recover from the service message error condition. For more information about printer messages, see the Menus and Messages book on the publications CD.
If you receive the following message, see Ordering a print cartridge.
Install the correct cartridge for the printer region. Region codes are:
0 = Worldwide 1 = Americas 2 = EMEA 3 = Asia 9 = Undefined
Technical support is available on our Lexmark Web site at www.lexmark.com.
If the printer is not responding, first make sure:
Once you have checked each of these possibilities, turn the printer off and back on. This often fixes the problem.
Message Action · Troubleshooting

Printing multi-language PDFs
Some documents do not print.
The documents contain unavailable fonts.
1 Open the document you want to print in Adobe Acrobat. 2 Click the printer icon. The Print dialog appears. 3 Check the Print as image box. 4 Click OK.
The operator panel display is blank or displays only diamonds.
The printer self test failed.
Turn the printer off, wait about 10 seconds, and turn the printer back on. If the Ready message does not appear, turn the printer off and call for service.
The message USB device unsupported appears when using a USB device.
The USB device you are using may not be supported or has an error. Only specific USB flash memory devices are supported.
For information regarding tested and approved USB flash memory devices, see our Lexmark Web site at http:// support.lexmark.com and click on KnowledgeBase to search for Direct USB printing.
Jobs do not print. The printer is not ready to receive data.
Make sure Ready or Power Saver appears on the display before sending a job to print. Press to return the printer to the Ready state.
The specified output bin is full.
Remove the stack of paper from the output bin, and then press .
The specified tray is empty.
Load paper in the tray.
You are using the wrong printer driver or are printing to a file.
Your MarkNet N8000 series internal print server is not set up properly or is not connected properly.
Verify that you have properly configured the printer for network printing. See the drivers CD or the Lexmark Web site for information.
You are using the wrong interface cable, or the cable is not securely connected.
Make sure you are using a recommended interface cable. Make sure the connection is secure.
Symptom Cause Solution · Symptom Cause Solution · Printing multi-language PDFs

Held jobs do not print. A formatting error has occurred.
The printer has received invalid data.
Delete the job.
Job takes longer than expected to print.
The job is too complex. Reduce the complexity of your print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Page Protect is set to On.
Set Page Protect to Off from the Setup Menu. For more information, see the Menus and Messages Guide.
Job prints from the wrong tray or on the wrong paper or specialty media.
The operator panel menu settings do not match the media loaded in the tray.
Make sure the Paper Size and Paper Type specified in the printer driver match the paper size and type in the tray.
Incorrect characters print.
You are using an incompatible parallel cable.
If you are using a parallel interface, make sure you are using an IEEE 1284-compliant parallel cable. We recommend Lexmark part number 1329605 (10 ft) or 1427498 (20 ft) for the standard parallel port.
The printer is in Hex Trace mode.
If Ready Hex appears on the display, you must exit Hex Trace mode before you can print your job. Turn the printer off and back on to exit Hex Trace mode.
Tray linking does not work.
Tray linking is not configured properly.
Large jobs do not collate. Collate is not set to On. Set Collation to On in the Finishing Menu or through the printer driver. Note: Setting Collation to Off in the driver overrides the setting in the Finishing Menu. See the Menus and Messages Guide for more information.
The job is too complex. Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
The printer does not have enough memory.
Add printer memory or an optional hard disk.
Unexpected page breaks occur.
The job has timed out. Set Print Timeout to a higher value from the Setup Menu. See the Menus and Messages Guide for more information.
Symptom Cause Solution · Solving printing problems

Solving option problems
If an option does not operate correctly after it is installed or if it quits working:
The following table lists printer options and suggested corrective actions for related problems. If the suggested corrective action does not fix the problem, call your service representative.
5-bin mailbox Make sure the connection between each 5-bin mailbox or the connection between the 5- bin mailbox and the printer is secure. If the 5-bin mailbox is listed on the menu settings page, but print media jams when it exits the printer and enters the mailbox, it may not be properly installed. Reinstall each 5-bin mailbox.
Flash memory Make sure flash memory is securely connected to the printer system board.
Hard disk with adapter
Make sure the hard disk is securely connected to the hard disk adapter card. Also, make sure the hard disk adapter card is securely connected to the printer system board.
Make sure the connection between the output stacker and the printer is secure. If the high- capacity output stacker is listed on the menu settings page, but print media jams when it exits the printer and enters the output stacker, it may not be properly installed. Reinstall the high-capacity output stacker.
Option Action · High-capacity output stacker · Solving option problems

Large capacity feeder (2000-sheet drawer)
See Solving 2000-sheet drawer problems.
Output expander Make sure the connection between each output expander or the connection between the output expander and the printer is secure. If the output expander is listed on the menu settings page, but print media jams when it exits the printer and enters the output expander, it may not be properly installed. Reinstall each output expander.
Printer memory Make sure printer memory is securely connected to the printer system board.

Solving 2000-sheet drawer problems
The elevator tray does not raise when the loading door is closed, or the elevator tray does not lower when the door is opened and the elevator button is pushed.
The elevator tray lowers unexpectedly. Check to see if the printer is out of print media or has a jam.
More than one sheet of print media is fed, or a sheet is fed improperly.
Remove the print media in the printer paper path, and check the stack to ensure the print media has been loaded properly. Be sure to remove the top and bottom sheets of each ream of paper that is loaded. A jam occurs.
Rubber feed rollers do not turn to advance print media.
Service messages A service message indicates printer failure that may require service. Turn the printer off, wait about 10 seconds, and then turn the printer on. If the error recurs, write down the error number, the problem, and a detailed description. Call for service.
Problem Solution · Solving option problems

Solving paper feed problems
Paper frequently jams. You are using paper that does not meet the printer specifications.
Use recommended paper and other specialty media. See the Card Stock & Label Guide available on our Lexmark Web site at www.lexmark.com for detailed specifications. See Avoiding jams for information that can help prevent jams from occurring.
You have loaded too much paper or too many envelopes.
Make sure the stack of paper you load does not exceed the maximum stack height indicated in the tray or on the multipurpose feeder.
Guides in the selected tray are not set to the appropriate position for the size paper loaded.
Move the guides in the tray to the correct position.
The paper has absorbed moisture due to high humidity.
Load paper from a fresh package. Store paper in its original wrapper until you load it. See Storing print media for more information.
The pick rolls may be worn. Replace the pick rolls. See Ordering pick rollers for more information.
The Paper Jam message remains after you remove the jammed paper.
You have not pressed Go or have not cleared the entire paper path.
Clear paper from the entire paper path, and then press . See Clearing jams for more information.
The page that jammed does not reprint after you clear the jam.
Jam Recovery in the Setup menu is set to Off.
Set Jam Recovery to Auto or On. See the Menus and Messages Guide for more information.
Blank pages feed into the output bin.
An incorrect media type is loaded in the tray being printed from.
Load the correct type media for your print job, or change the Paper Type to match the type of media loaded. See the Menus and Messages Guide for more information.
Solving paper feed problems
Symptom Cause Solution

Solving print quality problems
The information in the following table may help you solve print quality problems. If these suggestions still do not correct the problem, call for service. You may have a printer part that requires adjustment or replacement.
Toner smears or print comes off the page.
Toner appears on the back of the printed page.
Toner is on the transfer roll. To help prevent this, do not load print media that is smaller than the page size of the job to be printed. Open and close the printer top front cover to run the printer setup cycle and clean the transfer roll.
Toner fog or background shading appears on the page.
Solving print quality problems
Problem Action

Characters have jagged or uneven edges.
Solving print quality problems
Problem Action

Part or all of the page is printed in black.
Check the print cartridge to see if it is installed correctly.
The job prints, but the top and side margins are incorrect.
Some of the print is cut off on the sides, top, or bottom of the media.
Move the guides in the tray to the proper positions for the size loaded.
Print is skewed or inappropriately slanted.
Transparency print quality is poor.
Solving print quality problems
Problem Action

The quality menu operator panel options can be adjusted to help improve print quality.
Menu selection Purpose Values†
Print Resolution To select printed output resolution 600 dpi* 1200 Image Q 1200 dpi 2400 Image Q
Toner Darkness Lightens or darkens printed output and conserves toner
1–10 8* is the default setting. Select a lower number to lighten the printed output or save toner.
Brightness Adjusts the gray value of printed objects
-6 – +6 0* is the default setting.
Contrast Adjusts the contrast of printed objects 0–5 0* is the default setting.
† Values marked by an asterisk (*) are the factory default settings.
In addition, the Enhance Fine Lines and Gray Correction options can be enabled to improve print quality. These settings are available on the driver and on the printer Embedded Web Server (EWS) interface. For more information about these options, see the driver Help.
Driver option Purpose Values†
Enhance Fine Lines A selection to enable a print mode preferable for certain files containing fine line detail, such as architectural drawings, maps, electronic circuit diagrams, and flow charts
On In the driver, enable the check box.
Off* In the driver, disable the check box.
Gray Correction Automatically adjusts the contrast enhancement applied to images
Auto In the driver, enable the check box.
Off* In the driver, disable the check box.
† Values marked by an asterisk (*) are the factory default settings.
Solving print quality problems


Trademarks
Lexmark and Lexmark with diamond design, Drag’N’Print, MarkNet, and MarkVision are trademarks of Lexmark International, Inc. PrintCryption and StapleSmart are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
LEXFAX is a service mark of Lexmark International, Inc.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and the printer emulates the functions corresponding to the commands.
PostScript® is a registered trademark of Adobe Systems Incorporated. PostScript 3 is Adobe Systems’ designation of a set of printer commands (language) and functions included in its software products. This printer is intended to be compatible with the PostScript 3 language. This means the printer recognizes PostScript 3 commands used in various application programs, and the printer emulates the functions corresponding to the commands.
Details relating to compatibility are included in the Technical Reference.
Other trademarks are the property of their respective owners.
© 2005 Lexmark International, Inc. All rights reserved.
UNITED STATES GOVERNMENT RIGHTS This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.
The printer resident software contains software developed and copyrighted by Lexmark.
In addition, the printer resident software may contain:
Click the title of the document you want to review:
The Lexmark modified third-party software covered by these third-party licenses is free software; you can redistribute it and/or modify it under the terms of the licenses referenced above. These licenses do not provide you any rights to the Lexmark copyrighted software in this printer.
Since the third-party licensed software the Lexmark modifications are based on is supplied explicitly without warranty, use of the Lexmark modified version is similarly provided without warranty. See the warranty disclaimers in the referenced licenses for additional details.
To obtain source code files for the Lexmark modified GNU licensed software, launch the drivers CD that shipped with the printer and click Contact Lexmark.
For source code that is required to be made available with the product, see the publications CD in the en\OpenSource\ directory.
Trademarks

Conventions
The Lexmark family base printers, Types 4061-000, 4061-200, and 4061-400, and network printers, Types 4061-010, 4061- 210, and 4061-410, have been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
device, use a properly shielded and grounded cable such as Lexmark part number 1329605 for parallel attach or 12A2405 for USB attach. Use of a substitute cable not properly shielded and grounded may result in a violation of FCC regulations.
Conventions

Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services
Lexmark International, Inc.
740 West New Circle Road
Industry Canada compliance statement
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Avis de conformité aux normes de l’industrie du Canada
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
European Community (EC) directives conformity
This product is in conformity with the protection requirements of EC Council directives 89/336/EEC and 73/23/EEC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits.
A declaration of conformity with the requirements of the directives has been signed by the Director of Manufacturing and Technical Support, Lexmark International, S.A., Boigny, France.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
If this symbol appears on your product, the accompanying statement is applicable.

If this symbol appears on your product, the accompanying statement is applicable.
This equipment has undergone EMC registration as a household product. It can be used in any area, including a residential area.

Exposure to radio frequency radiation
The radiated output power of this device is far below the FCC radio frequency exposure limits. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC.
The United Kingdom Telecommunications Act 1984
This apparatus is approved under the approval number NS/G/1234/J/100003 for the indirect connections to the public telecommunications systems in the United Kingdom.
Die folgenden Messungen wurden gemäß ISO 7779 durchgeführt und gemäß ISO 9296 gemeldet.
Durchschnittlicher Schallpegel (dB(A)) in 1 m Umkreis
Drucken 53 55 55
Leerlauf 30 30 30

German GS mark notice
Physical address
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Printing 53 55 55
Idling 30 30 30
The EPA ENERGY STAR Office Equipment program is a partnership effort with office equipment manufacturers to promote the introduction of energy-efficient products and to reduce air pollution caused by power generation.
Companies participating in this program introduce products that power down when they are not being used. This feature will cut the energy used by up to 50 percent. Lexmark is proud to be a participant in this program.
As an ENERGY STAR Partner, Lexmark International, Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Waste from Electrical and Electronic Equipment (WEEE) directive
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products. If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
A laser notice label may be affixed to this printer.
VAROITUS! Laitteen käyttäminen muulla kuin tässä käyttoohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING! Om apparaten används på annat sätt än i denna bruksanvisning specificerats, kan avnändaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 5 milliwatt gallium arsenide laser operating in the wavelength region of 770-795 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
Lexmark International, Inc., Lexington, KY
This limited warranty applies to the United States and Canada. For customers outside the U.S., see the country-specific warranty information that came with your product.
This Statement of Limited Warranty applies to this product if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
Waste from Electrical and Electronic Equipment (WEEE) directive
Warranty

If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was designed. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase and ends 12 months later as shown on the purchase receipt provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Paper Feed items, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area, contact on the World Wide Web at http://support.lexmark.com
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Extent of limited warranty
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Statement of limited warranty
Limited warranty service · Limitation of liability

Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.
Statement of limited warranty
Additional rights


Pages referenced in this manual — manufacturer, support and downloads.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Some documents do not print. | The documents contain unavailable fonts. | 1 Open the document you want to print in Adobe Acrobat. 2 Click the printer icon. The Print dialog appears. 3 Check the Print as image box. 4 Click OK. | p.104 |
| The operator panel display is blank or displays only diamonds. | The printer self test failed. | Turn the printer off, wait about 10 seconds, and turn the printer back on. If the Ready message does not appear, turn the printer off and call for service. | p.104 |
| The message USB device unsupported appears when using a USB device. | The USB device you are using may not be supported or has an error. Only specific USB flash memory devices are supported. | For information regarding tested and approved USB flash memory devices, see our Lexmark Web site at http:// support.lexmark.com and click on KnowledgeBase to search for Direct USB printing. | p.104 |
| Jobs do not print. | The printer is not ready to receive data. | Make sure Ready or Power Saver appears on the display before sending a job to print. Press to return the printer to the Ready state. | p.104 |
| Jobs do not print. | The specified output bin is full. | Remove the stack of paper from the output bin, and then press . | p.104 |
| Jobs do not print. | The specified tray is empty. | Load paper in the tray. | p.104 |
| Jobs do not print. | You are using the wrong printer driver or are printing to a file. | • Verify you are using the printer driver associated with the printer. • If you are using a USB port, make sure you are running Windows 98/Me, Windows 2000, Windows XP, or Windows Server 2003 and using a Windows 98/Me, Windows 2000, Windows XP, or Windows Server 2003 compatible printer driver. | p.104 |
| Jobs do not print. | Your MarkNet N8000 series internal print server is not set up properly or is not connected properly. | Verify that you have properly configured the printer for network printing. See the drivers CD or the Lexmark Web site for information. | p.104 |
| Jobs do not print. | You are using the wrong interface cable, or the cable is not securely connected. | Make sure you are using a recommended interface cable. Make sure the connection is secure. | p.104 |
| Held jobs do not print. | A formatting error has occurred. | • Print the job. (Only part of the job may print.) • Delete the job. • Free up additional printer memory by scrolling through the list of held jobs and deleting others you have sent to the printer. | p.105 |
| Held jobs do not print. | The printer has insufficient memory. | p.105 | |
| Held jobs do not print. | The printer has received invalid data. | Delete the job. | p.105 |
| Job takes longer than expected to print. | The job is too complex. | Reduce the complexity of your print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job. | p.105 |
| Job takes longer than expected to print. | Page Protect is set to On. | Set Page Protect to Off from the Setup Menu. For more information, see the Menus and Messages Guide. | p.105 |
| Job prints from the wrong tray or on the wrong paper or specialty media. | The operator panel menu settings do not match the media loaded in the tray. | Make sure the Paper Size and Paper Type specified in the printer driver match the paper size and type in the tray. | p.105 |
| Incorrect characters print. | You are using an incompatible parallel cable. | If you are using a parallel interface, make sure you are using an IEEE 1284-compliant parallel cable. We recommend Lexmark part number 1329605 (10 ft) or 1427498 (20 ft) for the standard parallel port. | p.105 |
| Incorrect characters print. | The printer is in Hex Trace mode. | If Ready Hex appears on the display, you must exit Hex Trace mode before you can print your job. Turn the printer off and back on to exit Hex Trace mode. | p.105 |
| Tray linking does not work. | Tray linking is not configured properly. | • Make sure both the size and type of media are the same in both trays. • Make sure the paper guides in the trays are set for the correct size media. • Make sure the menu values for both size and type are set correctly in the Paper Menu. • See Linking trays, or see the Menus and Messages Guide for more information. | p.105 |
| Large jobs do not collate. | Collate is not set to On. | Set Collation to On in the Finishing Menu or through the printer driver. Note: Setting Collation to Off in the driver overrides the setting in the Finishing Menu. See the Menus and Messages Guide for more information. | p.105 |
| Large jobs do not collate. | The job is too complex. | Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job. | p.105 |
| Large jobs do not collate. | The printer does not have enough memory. | Add printer memory or an optional hard disk. | p.105 |
| Unexpected page breaks occur. | The job has timed out. | Set Print Timeout to a higher value from the Setup Menu. See the Menus and Messages Guide for more information. | p.105 |
| The elevator tray does not raise when the loading door is closed, or the elevator tray does not lower when the door is opened and the elevator button is pushed. | Check the following: • The printer is properly attached to the 2000-sheet drawer. • The printer is powered on. • The power cord is plugged firmly into the back of the 2000-sheet drawer. • The power cord is plugged into an outlet. • The outlet has power. | p.108 | |
| The elevator tray lowers unexpectedly. | Check to see if the printer is out of print media or has a jam. | p.108 | |
| More than one sheet of print media is fed, or a sheet is fed improperly. | Remove the print media in the printer paper path, and check the stack to ensure the print media has been loaded properly. Be sure to remove the top and bottom sheets of each ream of paper that is loaded. | p.108 | |
| A jam occurs. | p.108 | ||
| Rubber feed rollers do not turn to advance print media. | Check the following: • The power cord is plugged firmly into the back of the 2000-sheet drawer. • The power cord is plugged into an outlet. • The outlet has power. | p.108 | |
| Consistent misfeeds or jams in the drawer | Try the following: • Flex the paper. • Turn the print media over. Check the following: • Drawer is properly installed. • Print media is loaded correctly. • Print media is not damaged. • Print media meets specifications. • Guides are positioned correctly for the print media size selected. | p.108 | |
| Service messages | A service message indicates printer failure that may require service. Turn the printer off, wait about 10 seconds, and then turn the printer on. If the error recurs, write down the error number, the problem, and a detailed description. Call for service. | p.108 | |
| Paper frequently jams. | You are using paper that does not meet the printer specifications. | Use recommended paper and other specialty media. See the Card Stock & Label Guide available on our Lexmark Web site at www.lexmark.com for detailed specifications. See Avoiding jams for information that can help prevent jams from occurring. | p.109 |
| Paper frequently jams. | You have loaded too much paper or too many envelopes. | Make sure the stack of paper you load does not exceed the maximum stack height indicated in the tray or on the multipurpose feeder. | p.109 |
| Paper frequently jams. | Guides in the selected tray are not set to the appropriate position for the size paper loaded. | Move the guides in the tray to the correct position. | p.109 |
| Paper frequently jams. | The paper has absorbed moisture due to high humidity. | Load paper from a fresh package. Store paper in its original wrapper until you load it. See Storing print media for more information. | p.109 |
| Paper frequently jams. | The pick rolls may be worn. | Replace the pick rolls. See Ordering pick rollers for more information. | p.109 |
| The Paper Jam message remains after you remove the jammed paper. | You have not pressed Go or have not cleared the entire paper path. | Clear paper from the entire paper path, and then press . See Clearing jams for more information. | p.109 |
| The page that jammed does not reprint after you clear the jam. | Jam Recovery in the Setup menu is set to Off. | Set Jam Recovery to Auto or On. See the Menus and Messages Guide for more information. | p.109 |
| Blank pages feed into the output bin. | An incorrect media type is loaded in the tray being printed from. | Load the correct type media for your print job, or change the Paper Type to match the type of media loaded. See the Menus and Messages Guide for more information. | p.109 |
| Print is too light. | • The toner may be low. To utilize the remaining toner, remove the cartridge by gripping the handles with both hands. With the cartridge arrows pointing downward, firmly shake the print cartridge side-to-side and front-to-back several times to redistribute the toner. Reinstall the cartridge and then press . Repeat this procedure multiple times until the print remains faded. When the print remains faded replace the print cartridge. • Change the Toner Darkness setting in the Quality menu. • Change the Brightness setting in the Quality menu. • Change the Contrast setting in the Quality menu. • If you are printing on an uneven print surface, change the Paper Weight and Paper Texture settings in the Paper menu. • Verify the correct print media is being used. | p.110 | |
| Toner smears or print comes off the page. | • If you are printing on an uneven print surface, change the Paper Weight and Paper Texture settings in the Paper menu. • Verify the print media is within the printer specifications. See Understanding paper and specialty media guidelines for more details. If the problem continues, contact the Lexmark Customer Support Center at 1-800-Lexmark (1-800-539-6275) or http://support.lexmark.com. | p.110 | |
| Toner appears on the back of the printed page. | Toner is on the transfer roll. To help prevent this, do not load print media that is smaller than the page size of the job to be printed. Open and close the printer top front cover to run the printer setup cycle and clean the transfer roll. | p.110 | |
| Toner fog or background shading appears on the page. | • Check the print cartridge to make sure it is installed correctly. • Replace the print cartridge. | p.110 | |
| Entire page is white. | • Make sure the packaging material is removed from the print cartridge. • Check the print cartridge to be sure it is installed correctly. • The toner may be low. To utilize the remaining toner, remove the cartridge by gripping the handles with both hands. With the cartridge arrows pointing downward, firmly shake the print cartridge side-to-side and front-to-back several times to redistribute the toner. Reinstall the cartridge and then press . Repeat this procedure multiple times until the print remains faded. When the print remains faded replace the print cartridge. | p.111 | |
| Streaks appear on the page. | • The toner may be low. To utilize the remaining toner, remove the cartridge by gripping the handles with both hands. With the cartridge arrows pointing downward, firmly shake the print cartridge side-to-side and front-to-back several times to redistribute the toner. Reinstall the cartridge and then press . Repeat this procedure multiple times until the print remains faded. When the print remains faded replace the print cartridge. • If you are using preprinted forms, make sure the ink can withstand temperatures of 230°C (446°F). | p.111 | |
| Printing is too dark. | • Change the Toner Darkness setting in the Quality menu. • Change the Brightness setting in the Quality menu. • Change the Contrast setting in the Quality menu. Note: Macintosh computer users should make sure the lines per inch (lpi) setting is not set too high in the software application. | p.111 | |
| Characters have jagged or uneven edges. | • Change the Print Resolution setting in the Quality menu to 600 dpi, 1200 Image Q, 1200 dpi, or 2400 Image Q. • Enable Enhance Fine Lines. See the tables on page 113 for more settings information. • If you are using downloaded fonts, verify the fonts are supported by the printer, the host computer, and the software application. | p.111 | |
| Part or all of the page is printed in black. | Check the print cartridge to see if it is installed correctly. | p.112 | |
| The job prints, but the top and side margins are incorrect. | • Make sure the Paper Size setting in the Paper menu is correct. • Make sure the margins are set correctly in your software application. | p.112 | |
| Ghost images appear. | • Make sure the Paper Type setting in the Paper menu is correct. • Replace the photoconductor kit. | p.112 | |
| Gray background prints. | • The Toner Darkness setting may be too dark. Change the Toner Darkness setting in the quality menu. • Adjust the Brightness setting darker. • Adjust the Contrast setting lighter. • See the tables on page 113 for more settings information. • The print cartridge may be defective. Replace the print cartridge. | p.112 | |
| Some of the print is cut off on the sides, top, or bottom of the media. | Move the guides in the tray to the proper positions for the size loaded. | p.112 | |
| Print is skewed or inappropriately slanted. | p.112 | ||
| Transparency print quality is poor. | • Use only transparencies recommended by the printer manufacturer. • Make sure the Paper Type setting in the Paper menu is set to Transparency. | p.112 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.