EN
Lexmark logo
Official user manual

Lexmark 522

32 pages·1.1 MB·Printer·PDF·ENDEFRITNLJA
Lexmark 522
Table of Contents 37 sections Lexmark T522 · Setup Guide · May 2001 · www.lexmark.com · … ShowHide
Page 1 of the Lexmark 522 user manual — www.lexmark.com
Page 1 · click to enlarge
Page 1

Lexmark T522

Setup Guide

May 2001

www.lexmark.com

Page 2 of the Lexmark 522 user manual — CAUTION!
Page 2 · click to enlarge
Page 2
EditionMay 2001

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.

Comments about this publication may be addressed to Lexmark International, Inc., Department F95/032-2, 740 West New Circle Road, Lexington, Kentucky 40550, U.S.A. In the United Kingdom and Eire, send to Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. You can purchase additional copies of publications related to this product by calling 1-800-553-9727. In the United Kingdom and Eire, call 0628-481500. In other countries, contact your point of purchase.

References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any function- ally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.

Lexmark and Lexmark with diamond design and MarkNet are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. ImageQuick is a trademark of Lexmark International, Inc.

Other trademarks are the property of their respective owners.

© Copyright 2001 Lexmark International, Inc. All rights reserved.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS This software and documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 and in applicable FAR provisions: Lex- mark International, Inc., Lexington, KY 40550.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any questions on this statement should be directed to:

Director of Lab Operations Lexmark International, Inc. 740 West New Circle Road NW Lexington, KY 40550 (859) 232-3000

Refer to the Lexmark T620/T622 Publications CD for details.

  • If your product is NOT marked with this symbol , it MUST be connected to an electrical outlet that is properly grounded.
  • The power cord must be connected to an electrical outlet that is near the product and easily accessible.
  • Refer service or repairs, other than those described in the operating instructions, to a professional service person.
  • This product is designed, tested and approved to meet strict global safety standards with the use of specific Lexmark components. The safety features of some parts may not always be obvious. Lexmark is not responsible for the use of other replacement parts.
  • Your product uses a laser, exercise CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
  • Your product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.

Conventions

CAUTION!

FCC emissions information · Safety information

Page 3 of the Lexmark 522 user manual — Getting started
Page 3 · click to enlarge
Page 3

Getting started

1 Select a well-ventilated place to set up your printer. Allow at least as much space as shown in the illustration. Make sure you have a sturdy, low table or the optional printer stand on which to set the printer.

137.16 cm (4.5 ft)

304.8 mm (12 in.)

304.8 mm (12 in.)

508 mm (20 in.)

304.8 mm (12 in.)

2 Remove all items from the box except the printer. If any items are missing, contact the place where you bought the printer.

Lexmark 522 — Getting started diagram (page 3)
Fig. 1 · Getting started

Save the carton and packing material in case you need to repack the printer for ser- vice or storage.

Paper bail and bracket

ready to install it. Then ask someone to help you lift the printer using the hand- holds.

Operator panel overlay (non-English only)

Turn off the printer If your printer is already set up, make sure the printer power is off and the power cord and any cables are unplugged before installing any options.

Options compatibility Options compatible with the Lexmark T522TM printer are labeled with a colored triangle. Label locations are indicated in the illustrations in this book.

Troubleshooting If you encounter a problem while setting up the printer, refer to the Lexmark T522 Publications CD.

Show 6 more labels / short text on this page
CDs · Printer · Handhold · Power switch cover · 500 sheet drawer · Power cord
Page 4 of the Lexmark 522 user manual — Getting started
Page 4 · click to enlarge
Page 4
Lexmark 522 — Getting started diagram (page 4)
Fig. 2 · Getting started
Page 5 of the Lexmark 522 user manual — Step 1: Install paper options
Page 5 · click to enlarge
Page 5

Step 1: Install paper options

and printer

The table illustrates various combinations of paper options supported by your printer.

Attach up to: Four optional drawers.

Lexmark 522 — Step 1: Install paper options diagram (page 5)
Fig. 3 · Step 1: Install paper options

2000-Sheet drawer 250-Sheet drawer 500-Sheet drawer 500-Sheet Duplex unit Envelope feeder

Installing the 2000-sheet drawer Your printer supports one 2000-sheet drawer. It gives your printer added capacity by letting you load up to four reams (approximately 2,000 sheets) of 20 lb. paper.

Lexmark 522 — Step 1: Install paper options diagram (page 5)
Fig. 4 · Step 1: Install paper options

The 2000-sheet drawer is packaged with a User’s Guide that contains detailed instructions for instal- lation, setup, and use, including loading paper and removing paper jams.

When you have finished installing the 2000-sheet drawer, install any other drawers or an optional duplex unit that you may have purchased.

Lexmark T522 label (colored triangle)

Lexmark T522(n)

Page 6 of the Lexmark 522 user manual — 3 Attach another optional drawer, a duplex unit, or the printer:
Page 6 · click to enlarge
Page 6

Installing a 250-sheet or

Paper drawers attach under the printer and optional duplex unit. The printer automatically recognizes any drawer that has been installed.

500-sheet drawer

Lexmark 522 — 500-sheet drawer diagram (page 6)
Fig. 5 · 500-sheet drawer

A drawer consists of a paper tray and a support unit. The 250-sheet drawer and the 500-sheet drawer are installed the same way.

Lexmark T522 label (colored triangle)

1 Remove the tray from the support unit. Remove all packing material and tape from both the support unit and the tray.

Lexmark 522 — 500-sheet drawer diagram (page 6)
Fig. 6 · 500-sheet drawer

2 Place the support unit on top of any previously installed paper drawers, or the table or printer cabinet where you plan to use the printer.

Lexmark 522 — 500-sheet drawer diagram (page 6)
Fig. 7 · 500-sheet drawer

The tab, round peg, and square holes on top of any drawer help you seat the support unit so the edges are aligned properly. Make sure the support unit is securely in place.

3 Attach another optional drawer, a duplex unit, or the printer:

  • To attach a drawer, repeat steps 1 and 2.
  • To attach a duplex unit, see “Installing a duplex unit” on page 5.
  • To attach the printer, see “Setting up the printer” on page 6.
Show 4 more labels / short text on this page
Tray labels · Support unit · Tab · Square hole
Page 7 of the Lexmark 522 user manual — Installing a 250-sheet or
Page 7 · click to enlarge
Page 7

Installing a duplex unit The duplex unit attaches under the printer, below the stan- dard input tray and above any paper drawers.

Refer to the Lexmark T522 online information, on the Lex- mark T522 Publications CD, for details about using the duplex unit.

Lexmark T522 label (colored triangle)

1 Place the duplex unit on top of any installed paper drawers, or the table or printer cabinet where you plan to use the printer.

Lexmark 522 — Installing a 250-sheet or diagram (page 7)
Fig. 8 · Installing a 250-sheet or

The tab, round peg, and square holes on top of any drawer help you seat the duplex unit so the edges are aligned properly. Make sure it is securely in place.

2 Attach the printer. See “Setting up the printer” on page 6.

Back cover

Page 8 of the Lexmark 522 user manual — Installing a 250-sheet or
Page 8 · click to enlarge
Page 8

Setting up the printer In order to ensure adequate clearance when installing sys- tem board options, see “Install memory and option cards” starting on page 10 before you position the printer if:

  • You plan to install memory or option cards
  • You will have less than 605.6 mm (24 in.) clearance on the left side of the printer.

when you set it down. 1 Ask someone to help you lift the printer by the hand- holds and lower it onto the duplex unit, optional drawer, table or printer cabinet.

The tab, round peg, and square holes on top of any drawer or the duplex unit help you seat the printer so the edges are aligned properly. Make sure the printer is securely in place.

Lexmark 522 — Installing a 250-sheet or diagram (page 8)
Fig. 9 · Installing a 250-sheet or

2 Remove the print cartridge packaging.

a Push the release latch and open the printer

upper front door.

b Grasp the print cartridge by the hand grip and

pull the print cartridge up and out.

and

Page 9 of the Lexmark 522 user manual — Installing a 250-sheet or
Page 9 · click to enlarge
Page 9
Lexmark 522 — Installing a 250-sheet or diagram (page 9)
Fig. 10 · Installing a 250-sheet or

c Pull on each end of the plastic, V-shaped piece

and then pull the packaging material straight out. Discard all packaging material.

d Align the slides on the print cartridge with the

slots on the print cartridge cradle. Use the col- ored arrows inside the printer for placement.

e Guide the print cartridge down as it drops and

f Close the upper front door.

3 Attach decals to any optional paper trays.

Decals showing the number “1” are on your printer and the standard input tray. These decals keep the standard input tray paired with the printer.

If you purchased optional drawers, you received a sheet of decals.

Peel the decals from the sheet and attach them to the recessed areas on the drawer and the matching tray.

Page 10 of the Lexmark 522 user manual — Installing a 250-sheet or
Page 10 · click to enlarge
Page 10
Lexmark 522 — Installing a 250-sheet or diagram (page 10)
Fig. 11 · Installing a 250-sheet or

4 Attach the operator panel overlay.

If English is not your preferred language, attach the overlay with the appropriately translated names for the operator panel.

a Peel the protective backing off the overlay.

b Align the holes in the overlay with the buttons on

the operator panel and press it into place.

c Rub the overlay firmly to make sure it adheres

securely to the operator panel.

d Peel the protective covering away from the over-

lay.

5 Attach the paper bail.

Lexmark 522 — Installing a 250-sheet or diagram (page 10)
Fig. 12 · Installing a 250-sheet or

a Remove the printer top cover and slide the plas-

tic bracket onto the static brush holder. Adjust the bracket so it is centered over the area where paper exits.

b Place the tips of the wire paper bail into the ends

of the plastic bracket so that the bail curves downward.

c Replace the top cover.

Page 11 of the Lexmark 522 user manual — Installing a 250-sheet or
Page 11 · click to enlarge
Page 11
Lexmark 522 — Installing a 250-sheet or diagram (page 11)
Fig. 13 · Installing a 250-sheet or

Installing the envelope feeder The envelope feeder attaches to the front of your printer behind the lower front door. It can be removed when you are not using it, making the printer more compact.

Refer to the Lexmark T522 online information for details about using the envelope feeder.

1 Push the release latch and open the printer lower front door.

2 Lift open the envelope feeder connector door.

3 Align the tabs on the envelope feeder with the slots on both sides of the printer, and then gently push the envelope feeder into the opening until it snaps into place.

The envelope feeder tilts downward at a slight angle when it is installed properly.

Page 12 of the Lexmark 522 user manual — Step 2: Install memory and
Page 12 · click to enlarge
Page 12

Step 2: Install memory and

option cards

You can customize your printer memory capacity and con- nectivity by adding optional cards. The instructions in this section help you install any of the following options:

  • Printer memory
  • Flash memory
  • Tri-Port Adapter
  • USB/Parallel 1284-C Interface Card
  • Parallel 1284-C Interface Card
  • MarkNet™ internal print servers (also called internal network adapters or INAs)
  • Hard disk
  • Optional firmware card
Lexmark 522 — Step 2: Install memory and diagram (page 12)
Fig. 14 · Step 2: Install memory and

You must access the printer system board to install printer memory, flash memory, or an option card.

1 Make sure the printer power is off, the printer power cord is unplugged, and all cables are disconnected from the back of the printer.

2 Press the release latches to open the upper and lower front doors.

Page 13 of the Lexmark 522 user manual — Step 2: Install memory and
Page 13 · click to enlarge
Page 13
Lexmark 522 — Step 2: Install memory and diagram (page 13)
Fig. 15 · Step 2: Install memory and

3 Press down on the side door latches and open the side door.

4 Loosen, but do not remove, the six screws on the shield.

You need a small Phillips screwdriver to loosen these screws.

5 Use the tabs to slide the shield up until the top three screws fit into the three keyholes on the shield.

6 Hold the shield by the tabs and lift it off.

Page 14 of the Lexmark 522 user manual — Step 2: Install memory and
Page 14 · click to enlarge
Page 14
Lexmark 522 — Step 2: Install memory and diagram (page 14)
Fig. 16 · Step 2: Install memory and

mark printers cannot be used with your printer. Refer to the Lexmark T522 Publications CD for specifications. 1 Follow the steps in “Accessing the printer system board” on page 10.

by static electricity. Touch something metal on the printer before you touch the mem- ory option.

2 Unpack the memory option. Avoid touching the connection points along its edge. Save the packaging materials.

3 Open both latches on the connector completely. Insert the memory option straight into the connector with the connection points pointing toward the system board.

4 Push the memory card firmly into the connector until it snaps into place. Make sure each latch fits over the notch located on either side of the option card.

Lexmark 522 — Step 2: Install memory and diagram (page 14)
Fig. 17 · Step 2: Install memory and

5 Follow the steps in “Reattaching the shield and closing the doors” on page 16.

Connection points Latch · Latch

Page 15 of the Lexmark 522 user manual — 1 Access the system board. (See page 10 for instructions.)
Page 15 · click to enlarge
Page 15

Installing an optional

Follow the instructions in this section to install an optional firmware card. The system board has one location where a firmware card can be installed.

firmware card

1 Access the system board. (See page 10 for instructions.)

aged by static electricity. Touch something metal on the printer before you touch a card.

2 Unpack the firmware card.

Lexmark 522 — 1 Access the system board. (See page 10 for instructions.) diagram (page 15)
Fig. 18 · 1 Access the system board. (See page 10 for instruct…

Avoid touching the metal contacts on the connector. Save the packaging.

3 Hold the firmware card by its edges, and align the two pins on the card with the holes on the system board.

Orient the card so that the pins are closest to the bottom edge of the system board.

4 Push in until the firmware card is firmly in place.

touch the system board. Some force may be required to fully install the firmware card. 5 Follow the steps in “Reattaching the shield and closing the doors” on page 16.

Page 16 of the Lexmark 522 user manual — Installing an optional
Page 16 · click to enlarge
Page 16

Installing an option card Your printer has two connectors that support the following option cards:

  • Hard disk with adapter card
  • MarkNet internal print server
  • USB/Parallel 1284-C Interface Card

Install a MarkNet internal print server to add an Ethernet or Token-Ring port for connecting your printer to a network.

Install a MarkNet N2501e or N2401e internal print server if you received either of these cards as part of a multifunction printer upgrade.

  • Parallel 1284-C Interface Card
  • Coax/Twinax Adapter for SCS
  • Tri-Port Adapter

Refer to the documentation included with each card for detailed information about that specific card.

You need a small Phillips screwdriver to install these options.

Install a Tri-Port Adapter to add LocalTalk, serial, and infrared ports. For details on setting up and using the Tri-Port Adapter, refer to the docu- mentation that shipped with the card.

print server already installed.

Install a USB/Parallel 1284-C interface card to add a Universal Serial Bus (USB) port or a parallel port.

Install a hard disk with adapter card to add additional storage space to your printer.

Lexmark 522 — Installing an optional diagram (page 16)
Fig. 19 · Installing an optional

1 Follow the steps in “Accessing the printer system board” on page 10.

aged by static electricity. Touch something metal on the printer before you touch the card.

2 Locate the card connectors on the system board. If you are installing only one card, install it in connector 1. If you are installing two cards, use connector 1 first and then connector 2.

Page 17 of the Lexmark 522 user manual — Installing an optional
Page 17 · click to enlarge
Page 17
Lexmark 522 — Installing an optional diagram (page 17)
Fig. 20 · Installing an optional

3 Remove and save the two screws on the back of the printer that attach the metal plate to the slot. Remove and discard the plate.

4 Unpack the card. Save the packaging materials.

5 Align the connection points on the card with the connector on the system board and push the card firmly into the system board connector.

6 Insert the two screws saved from the metal plate (or the extra screws shipped with the card) into the holes.

7 Tighten the screws to secure the card.

Page 18 of the Lexmark 522 user manual — Installing an optional
Page 18 · click to enlarge
Page 18
Lexmark 522 — Installing an optional diagram (page 18)
Fig. 21 · Installing an optional

After you have installed option cards on the printer system board, follow these steps to reattach the shield and close the doors.

1 Grasp the shield by the tabs and align the three key- holes on the shield with the top three screws. Hold- ing the shield by the tabs, slide it down onto the screws. Tighten all six screws.

2 Close the side door.

Lexmark 522 — Installing an optional diagram (page 18)
Fig. 22 · Installing an optional

3 Close the upper and lower front doors.

up the printer” beginning on page 6, do so now.

Page 19 of the Lexmark 522 user manual — Step 3: Load print material
Page 19 · click to enlarge
Page 19

Step 3: Load print material

Complete these instructions to load print material into any of the standard or optional trays. All paper trays are loaded in the same way.

Lexmark 522 — Step 3: Load print material diagram (page 19)
Fig. 23 · Step 3: Load print material

1 Remove the paper tray.

2 Pull the width guide tab and slide the width guide to the far right side of the tray.

3 Squeeze the length guide lever and slide the length guide to the correct position for the size paper you are loading.

. 4 Place the paper into the paper tray with the recommended print side face down for single-sided printing and face up for duplex printing. Do not fill paper above the paper capacity mark (fill line).

5 Pull the width guide tab and slide the width guide to the left until it lightly rests against the edge of the paper stack.

6 Reinstall the tray.

Lexmark 522 — Step 3: Load print material diagram (page 19)
Fig. 24 · Step 3: Load print material
Page 20 of the Lexmark 522 user manual — Step 4: Attach cables
Page 20 · click to enlarge
Page 20

Step 4: Attach cables

You can attach your printer to a network or locally (directly to a computer).

Network printing You can attach your printer to a network using standard network cables.

A 10BaseT/100BaseTX Fast Ethernet port is standard on the Lexmark T522 printer. You can add a Token-Ring or 10Base2 Ethernet port by installing an optional MarkNet internal print server.

To attach the printer to a network:

1 Make sure the printer, computer, and any other attached devices are turned off and unplugged.

2 Connect the printer to a LAN drop or hub using standard cabling that is compatible with your network.

The printer automatically adjusts itself for the net- work speed.

– Token-Ring, Ethernet 10BaseT, or Ethernet 100BaseTX networks (Category 5) use an RJ-45 connector.

Page 21 of the Lexmark 522 user manual — Step 4: Attach cables
Page 21 · click to enlarge
Page 21

– Token-Ring networks (Shielded Twisted Pair) use a DB9 connector.

– Ethernet 10Base2 networks (Thin Coax) use a BNC T-connector.

Local printing You can attach your printer locally using either the USB port or parallel port. A USB port is standard on all printer models. The parallel port is standard on the base (non- network) model. The parallel port requires an IEEE-1284 compliant parallel cable. We recommend Lexmark part number 1329605 (10 ft) or 1427498 (20 ft).

If you add a parallel port by installing an optional USB/Par- allel Interface Card, you need a 1284 A-C parallel cable, such as Lexmark part number 43H5171 (9.8 ft).

support USB connections. Consult your computer documentation to see if your system supports USB.

Page 22 of the Lexmark 522 user manual — Step 4: Attach cables
Page 22 · click to enlarge
Page 22

If you have installed an optional Tri-Port Adapter, you can locally attach the printer with a serial cable. We recom- mend Lexmark part number 1038693 (50 ft). For details on LocalTalk or infrared connections, refer to the docu- mentation that shipped with the Tri-Port Adapter.

cable connections. However, only the Windows 98/ Me and Windows 2000 operating systems support USB cable connections.

To attach the printer to a computer:

1 Make sure the printer, computer, and any other attached devices are turned off and unplugged.

2 Connect the printer to the computer using a parallel or USB cable.

– Use an IEEE-1284 compliant parallel cable to ensure that you can access all of your printer functions.

– Be sure to match the USB symbol on the cable to the USB symbol on the printer.

Page 23 of the Lexmark 522 user manual — Step 5: Verify printer setup
Page 23 · click to enlarge
Page 23

Step 5: Verify printer setup

Turning on the printer 1 Plug one end of the printer power cord into the socket at the back of the printer and the other end into a properly grounded outlet.

2 Turn on the printer. If the printer is attached locally (directly to a computer), leave the computer and any other attached devices turned off. You will turn these on in a later step.

The printer requires time to warm up after you turn it on. During this period, the message Performing Self Test appears on the operator panel display.

After the printer completes its internal tests, the Ready message indicates the printer is ready to receive jobs.

If you see other messages on the display, refer to the Lexmark T522 Publications CD for instructions on clearing the message. Click Printing, and then click Understanding printer messages.

3 Go to “Printing a menu settings page” on page 22. If you attached the printer to a network, see “Printing a network setup page”.

operator panel display. Refer to the Lexmark T522 Publications CD for instructions.

Printing a network setup page If the printer is attached to a network, print a network setup page to verify the network connection. This page also provides important information that will help you con- figure for network printing.

Page 24 of the Lexmark 522 user manual — 3 Verify that the options you installed are listed under “Installed Features.”
Page 24 · click to enlarge
Page 24

1 Press Menu until you see Utilities Menu, and then press Select.

2 Press Menu until you see Print Net Setup, and then press Select to print the page.

The network setup page prints and the printer returns to Ready status.

1 Menu 2 Select 3 Return 4

3 Check the first section on the network setup page and confirm that Status is “Connected.”

Go 5 Stop 6

you see Print Net1 Setup. If the card is installed in Slot 2, you see Print Net2 Setup.

If Status is “Not Connected,” your LAN drop may not be active or your network cable may be malfunction- ing. Consult your network support person, and then print another network setup page to verify that you are connected to your network.

Save the network setup page for use with later instructions.

Printing a menu settings page Print the menu settings page to review the default printer settings and to verify that printer options are installed cor- rectly. For more information about using the printer opera- tor panel and changing menu settings, refer to the Lexmark T522 Publications CD.

1 Press Menu until you see Utilities Menu, and then press Select.

2 Press Menu until you see Print Menus, and then press Select to print the page.

The message Printing Menus is displayed.

3 Verify that the options you installed are listed under “Installed Features.”

If an option you installed is not listed, turn the printer off, unplug the power cord, and reinstall the option.

4 Verify the amount of memory installed is correctly listed under “Printer Information.”

5 Verify that the paper trays are configured for the sizes and types of paper you loaded in the printer.

Ready

Page 25 of the Lexmark 522 user manual — IP address
Page 25 · click to enlarge
Page 25

Step 6: Configure for TCP/IP

If you have TCP/IP available on your network, we recom- mend that you assign an IP address to the printer.

Setting the printer

If your network is using DHCP, an address is automatically assigned.

IP address

1 Look for the address under the TCP/IP heading on the network setup page you printed in “Printing a network setup page” on page 21.

2 Go to “Verifying the IP settings” on page 24 and begin with step 2.

ting the IP address in the online documentation on the drivers CD that shipped with your printer.

If your network is not using DHCP, then you must manually assign an IP address. One of the easiest ways is to use the operator panel:

1 Press Menu until you see Network Menu, and then press Select.

2 Press Menu until you see Standard Network, and then press Select.

Standard Network appears if you purchased a printer with an on-board network port. If you have an optional MarkNet card installed in Slot 1, you see Network Option 1. If the card is installed in Slot 2, you see Network Option 2.

3 Press Menu until you see Std Net Setup, and then press Select.

4 Press Menu until you see TCP/IP, and then press Select.

5 Press Menu until you see Set IP Address, and then press Select.

Page 26 of the Lexmark 522 user manual — Configure for Pull Printing (ImageQuick)
Page 26 · click to enlarge
Page 26

6 Change the address by pressing Menu to increase (or decrease) each number. Press Select to move to the next segment. Press Select when you are finished.

The message Saved appears briefly.

7 Press Menu until you see Set IP Netmask, and then press Select.

8 Repeat step 6 to set the IP Netmask.

9 Press Menu until you see Set IP Gateway, and then press Select.

10 Repeat step 6 to set the IP Gateway.

11 When you are finished, press Go to return the printer to the Ready state.

Verifying the

1 Print another network setup page and make sure the IP Address, Netmask, and Gateway are what you expected.

IP settings

Use the information in “Printing a network setup page” on page 21 if you need help.

2 Ping the printer and verify that it responds.

For example, at a command prompt on a network computer type “ping” followed by the new printer IP address:

ping xxx.xxx.xxx.xx

If the printer is active on the network, you will receive a reply.

Configure for Pull Printing (ImageQuick)

If your printer has an optional ImageQuick™ firmware card installed, you can configure for Pull Printing once an IP address has been assigned to your printer.

For detailed configuration instructions, refer to the online documentation on the ImageQuick CD. The ImageQuick CD is shipped with printers that have the optional ImageQuick firmware card preinstalled, and also with the firmware card if you purchased it separately.

Page 27 of the Lexmark 522 user manual — Printer drivers
Page 27 · click to enlarge
Page 27

Step 7: Install printer drivers

A printer driver is software that lets your computer commu- nicate with your printer.

The following table is a quick guide to finding the specific instructions you need.

Type of printer installation Network environment or operating system Page

(Ethernet or Token-Ring connections)

(Windows 95/98/Me, Windows NT 4.0, Windows 2000)

(parallel or USB connections)

(Windows 95/98/Me, Windows NT 4.0, Windows 2000)

Network printing The following instructions explain how to install printer drivers on printers attached to a network.

Windows Ports

The following network printer ports are supported:

  • Microsoft IP port (Windows NT 4.0 and Windows 2000)
  • Lexmark network port (Windows 95/98/Me, Windows NT 4.0, and Windows 2000)

Printer drivers

a Lexmark network port provides enhanced func- tionality, such as printer status alerts.

The following printer drivers are supported:

  • Windows system printer driver
  • Lexmark T522 custom printer driver
Show 9 more labels / short text on this page
Network · Windows · Macintosh 26 · UNIX/Linux 27 · NetWare 27 · Local · Windows · Macintosh 28 · UNIX/Linux 29
Page 28 of the Lexmark 522 user manual — Creating ports and installing drivers
Page 28 · click to enlarge
Page 28

System drivers are built into Windows operating systems. Custom drivers are available on the drivers CD.

Updated system and custom drivers are available on the Lexmark Web site at www.lexmark.com/drivers

Printing methods

The following network printing methods are supported:

  • Direct IP printing
  • Shared printing (point and print, peer-to-peer)

Creating ports and installing drivers

Read the detailed instructions on the drivers CD. Click View documentation and look for network printer installa- tion.

If you choose to install without using the instructions on the drivers CD, you need a basic understanding of net- work printing on TCP/IP networks, printer driver installa- tion, and the process involved in adding new network ports.

Macintosh Your Lexmark T522 printer connects automatically to AppleTalk networks and becomes readily visible to other network clients.

You must create a printer object (icon) on the desktop of each network client using the LaserWriter 8 printer driver and the Lexmark T522 PostScript Printer Description (PPD) file.

about the capabilities of a printer to UNIX or Macin- tosh drivers or applications.

A printer object (icon) must be created on the desktop of each network client using the LaserWriter 8 printer driver and the Lexmark T522 PostScript Printer Description (PPD) file.

Specific information about installing the printer on your AppleTalk network is found in the online documentation on the drivers CD that shipped with your printer.

A Lexmark PPD Installer is provided in the downloadable Web package available on the Lexmark Web site at www.lexmark.com

Page 29 of the Lexmark 522 user manual — Non-NDPS (queue-based)
Page 29 · click to enlarge
Page 29

Depending upon which drivers CD shipped with your printer, you may also find this software on the drivers CD. Launch this utility and follow the instructions to install the PPDs. Send a test print job when you have finished.

UNIX/Linux Your printer supports many UNIX platforms, such as Sun Solaris and Linux.

drivers CD and on the Lexmark Web site at www.lexmark.com/drivers

Lexmark provides a printer driver package for each sup- ported UNIX platform containing all the necessary drivers and PPDs. The user’s guide contained in each package gives detailed instructions for installing and using Lexmark printers in UNIX environments.

You can download these printer driver packages from Lex- mark’s Web site at www.lexmark.com/drivers Depending on which drivers CD shipped with your printer, you may also find the driver package you need on the CD.

NetWare Your Lexmark T522 printer works with both Novell Distrib- uted Print Services (NDPS) and regular queue-based Net- Ware environments.

Novell Distributed Print Services (NDPS)

If you have an NDPS environment, we recommend you install the Lexmark NDPS IP Gateway. The gateway tightly integrates your printers with NDPS so you can easily mon- itor, control, and print to them.

You can get the gateway, the snap-ins, the support files, and a white paper with installation instructions on the Web at www.lexmark.com/networking/ndps.html

Additional information about network printer installation can be found at www.lexmark.com/publications or on the drivers CD that shipped with your printer.

Non-NDPS (queue-based)

For the latest information about Lexmark support for non- NDPS (queue-based) environments, click View Documen- tation on the drivers CD and look for network printer instal-

Page 30 of the Lexmark 522 user manual — Installation instructions
Page 30 · click to enlarge
Page 30

lation. This documentation is also available on the Lexmark Web site at www.lexmark.com/publications

Local printing The following instructions explain how to install a printer driver on a printer attached to a computer using a parallel or USB connection.

Windows Supported connections

The following printer connections are supported:

  • Parallel (Windows 95/98/Me, Windows NT 4.0, and Windows 2000)
  • USB (Windows 98/Me and Windows 2000)

vides enhanced functionality, such as printer status alerts.

Printer drivers

The following printer drivers are supported:

  • Windows system printer driver
  • Lexmark T522 custom printer driver

System drivers are built into Windows operating systems. Custom drivers are available on the drivers CD.

Updated system and custom drivers are available at www.lexmark.com/drivers

Installation instructions

Read the detailed online instructions on the drivers CD. Click View documentation and look for information about local printer installation. Detailed instructions are provided for parallel and USB connections.

Macintosh If you are setting up the printer for local printing, you need to install the Lexmark T522 PPD and use it with the Laser- Writer 8 printer driver or the Adobe PostScript driver.

The Lexmark T522 PPD and specific information about local printer installation on Macintosh computers can be found on the drivers CD that shipped with your printer.

After the printer is installed, print a test page to verify your printer is correctly set up.

Page 31 of the Lexmark 522 user manual — Windows Supported connections
Page 31 · click to enlarge
Page 31

UNIX/Linux Your printer supports many UNIX platforms, such as Sun Solaris and Linux.

drivers CD and on the Lexmark Web site at www.lexmark.com/drivers

Lexmark provides a printer driver package for each sup- ported UNIX platform containing all the necessary drivers and PPDs. The user’s guide contained in each package gives detailed instructions for installing and using Lexmark printers in UNIX environments.

All the driver packages support local printing using a paral- lel connection. The driver package for Sun Solaris sys- tems also supports USB connections to Sun Ray appliances and Sun workstations.

You can download these printer driver packages from Lex- mark’s Web site at www.lexmark.com/drivers Depending on which drivers CD shipped with your printer, you may also find the driver package you need on the CD.

Page 32 of the Lexmark 522 user manual — www.lexmark.com
Page 32 · click to enlarge
Page 32

P/N 09H0401 E.C. 2H0000

Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. © 2001 Lexmark International, Inc. 740 West New Circle Road Lexington, Kentucky 40550

www.lexmark.com

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Lexmark 522

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lexmark 522

Be the first to ask — other owners or our team will answer.

Original document

Lexmark 522 manual PDF

32 pages·1.1 MB·Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…