
User's Guide
Machine type(s):
Model(s):
415, 436


Connect the power cord to a properly grounded electrical outlet that is near the product and easily accessible.
Do not place or use this product near water or wet locations.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
Use only the power cord provided with this product or the manufacturer's authorized replacement.
Use only the telecommunications (RJ‑11) cord provided with this product or a 26 AWG or larger replacement when connecting this product to the public switched telephone network.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a service representative.
Safety information 7

SAVE THESE INSTRUCTIONS.
Safety information 8

Learning about the printer 9
Finding information about the printer

Learning about the printer 10
When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any options, then leave enough room for them also. It is important to:

Learning about the printer 11


Learning about the printer 12

1 Printer control panel
9 Optional 550-sheet tray (Tray 3)

Learning about the printer 13
Automatic document feeder (ADF) Scanner glass

Use the scanner glass for single‑page documents, book pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
Use the ADF for multiple‑page documents including two- sided (duplex) pages.
When using the ADF:
When using the scanner glass:

Understanding the printer control panel 14
Using the printer control panel

4 Clear all / Reset button Reset the default settings of a function, such as printing, copying, or e-mailing.
6 Sleep button Enable Sleep mode or Hibernate mode.
8 Start button Start a job, depending on which mode is selected.
9 Indicator light Check the status of the printer.
10 USB port Connect a flash drive to the printer.
When the printer is turned on, the display shows a basic screen, referred to as the home screen. Use the home screen buttons and icons to initiate an action such as copying, faxing, or scanning; to open the menu screen; or respond to messages.

Understanding the printer control panel 15

1 Copy Access the Copy menus and make copies.
2 Fax Access the Fax menus and send fax.
3 E‑mail Access the E-mail menus and send e‑mails.
4 FTP Access the File Transfer Protocol (FTP) menus and scan documents directly to an FTP server.
5 Menu icon Access printer menus.
This may also appear on the home screen:

Jobs by user Access print jobs saved by user.

Attendance message alert If an attendance message affects a function, then this icon appears and the red indicator light blinks.
Touch To

Understanding the printer control panel 16
The IP address of your printer is located at the top left corner of the home screen and appears as four sets of numbers separated by periods. You can use the IP address when accessing the Embedded Web Server to view and remotely configure printer settings even when you are not physically near the printer.
The colors of the Sleep button and indicator lights on the printer control panel signify a certain printer status or condition.
Indicator light Printer status
Off The printer is off or in Hibernate mode.
Blinking green The printer is warming up, processing data, or printing.
Solid green The printer is on, but idle.
Blinking red The printer requires user intervention.
Sleep button light Printer status
Off The printer is off, idle or in Ready state.
Solid amber The printer is in Sleep mode.
Blinking amber The printer is entering or waking from Hibernate mode.
Blinking amber for 0.1 second, then goes completely off for 1.9 seconds in a slow, pulsing pattern
The printer is in Hibernate mode.
Feature Description · Printer IP address

Understanding the printer control panel 17

1 Arrows View a list of options.
2 Copy It Print a copy.
3 Advanced Options Select a copy option.
4 Home Go to the home screen.
5 Increase Select a higher value.
6 Decrease Select a lower value.
7 Tips Open a context-sensitive Help dialog.
Save a setting.
Reset values on the screen.

Setting up and using the home screen applications 18
The computer IP address is required when setting up home screen applications, such as:
1 Open the command window.
From the Search charm, type run, and then navigate to:
Apps list > Run > type cmd > OK
or click Start, and then click Run. b In the Start Search or Run dialog, type cmd.
c Press Enter, or click OK.
2 Type ipconfig, and then click Go or press Enter.
3 Look for IP Address.
The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123.
1 From the Apple menu, navigate to:
System Preferences > Network
2 Click Ethernet, Wi‑Fi, or AirPort.
a Click

Setting up and using the home screen applications 19
3 Click Advanced > TCP/IP.
4 Look for IPv4 Address.
You can find the printer IP address:
The Embedded Web Server is the printer Web page that lets you view and remotely configure printer settings even when you are not physically near the printer.
2 Open a Web browser, and then type the printer IP address in the address field.
3 Press Enter.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Do one or more of the following: • Show or hide the icons of basic printer functions. a Click Settings > General Settings > Home screen customization. b Select the check boxes to specify which icons appear on the home screen.

Setting up and using the home screen applications 20
Card Copy Scan and print both sides of a card on a single page. For more information, see “Setting up Card Copy” on page 21.
Fax Scan a document, and then send it to a fax number. For more information, see “Faxing” on page 92.
Forms and Favorites Quickly find and print frequently used online forms directly from the printer home screen. For more
information, see “Setting up Forms and Favorites” on page 20.
Multi Send Scan a document, and then send it to multiple destinations. For more information, see “Setting up Multi Send” on page 22.
MyShortcut Create shortcuts directly on the printer home screen. For more information, see “Using MyShortcut” on page 22.
Scan to E‑mail Scan a document, and then send it to an e‑mail address. For more information, see “E-mailing” on page 85.
Scan to Computer Scan a document, and then save it to a predefined folder on a host computer. For more information, see “Setting up Scan to Computer” on page 118.
Scan to FTP Scan documents directly to a File Transfer Protocol (FTP) server. For more information, see “Scanning to an FTP address” on page 115.
Scan to Network Scan a document, and then send it to a network shared folder. For more information, see “Setting up Scan to Network” on page 23.
Your printer comes with preinstalled home screen applications. Before you can use these applications, you must first activate and set up these applications using the Embedded Web Server. For more information on accessing the Embedded Web Server, see “Accessing the Embedded Web Server” on page 19.
For more information on configuring and using the home screen applications, do the following:
1 Go to http://support.lexmark.com, and then click SELECT YOUR PRODUCT > .
3 Click the Manuals tab, and then select the document for the home screen application.
Use To

Setting up and using the home screen applications 21

Streamline work processes by letting you quickly find and print frequently used online forms directly from the printer home screen.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Apps > Apps Management > Forms and Favorites.
3 Click Add, and then customize the settings.
4 Click Apply.
To use the application, touch Forms and Favorites on the printer home screen, and then navigate through form categories, or search for forms based on a form number, name, or description.

Quickly and easily copy insurance, identification, and other wallet‑size cards.
You can scan and print both sides of a card on a single page, saving paper and showing the information on the card in a more convenient manner.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Apps > Apps Management > Card Copy.
Use To · Use To

Setting up and using the home screen applications 22
– When scanning a card, make sure the scan resolution is not more than 200 dpi for color, and 400 dpi for
black and white. – When scanning multiple cards, make sure the scan resolution is not more than 150 dpi for color, and
300 dpi for black and white. • Print Borders—Select the check box to print the scan image with a border around it.
4 Click Apply.
To use the application, touch Card Copy on the printer home screen, and then follow the instructions.

Create shortcuts on the printer home screen, with settings for up to 25 frequently used copy, fax, or e- mail jobs.
To use the application, touch MyShortcut, and then follow the instructions on the printer display.

Scan a document, and then send the scanned document to multiple destinations.
Use To · Use To

Setting up and using the home screen applications 23
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Apps > Apps Management > Multi Send.
3 From the Profiles section, click Add, and then customize the settings.
4 Click Apply.
To use the application, touch Multi Send on the printer home screen, and then follow the instructions on the printer display.

Scan a document and send it to a shared network folder. You can define up to 30 unique folder destinations.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Apps > Apps Management > Scan to Network.
3 Specify the destinations, and then customize the settings.
4 Click Apply.
Use To

Setting up and using the home screen applications 24
To use the application, touch Scan to Network on the printer home screen, and then follow the instructions on the printer display.
This application shows the printer control panel on your computer screen and lets you interact with the printer control panel, even when you are not physically near the network printer. From your computer screen, you can view the printer status, release held print jobs, create bookmarks, and do other print-related tasks you might normally do while standing at the network printer.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Remote Operator Panel Settings.
3 Select the Enabled check box, and then customize the settings.
4 Click Submit.
To use the application, click Remote Operator Panel > Launch VNC Applet.
You can export configuration settings into a text file, and then import the file to apply the settings to other printers.
1 Open a Web browser, and then type the printer IP address in the address field.
2 To export or import a configuration for one application, do the following: a Click Settings > Apps > Apps Management. b From the list of installed applications, click the name of the application you want to configure.
c Click Configure, and then do either of the following:
– When saving the configuration file, you can type a unique file name or use the default name. – If a "JVM Out of Memory” error occurs, then repeat the export process until the configuration file is
saved. • To import a configuration from a file, click Import, and then browse to the saved configuration file that was exported from a previously configured printer.
– Before importing the configuration file, you can choose to preview it first or load it directly. – If a timeout occurs and a blank screen appears, then refresh the Web browser, and then click Apply.

Setting up and using the home screen applications 25
3 To export or import a configuration for multiple applications, do the following: a Click Settings > Import/Export. b Do either of the following:

Additional printer setup 26
Installing internal options
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electircal outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.

Additional printer setup 27
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board at the back of the printer.
2 Turn the screws counterclockwise to remove them.

3 Slightly open the controller board access cover, and then shift to the right to remove it.


4 Locate the appropriate connector on the controller board.

Additional printer setup 28

1 Memory card connector
2 Option card connector
5 Reattach the cover.



Additional printer setup 29
6 Turn the screws clockwise to lock the cover.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 27.
2 Unpack the memory card.

Additional printer setup 30
3 Align the notch (1) on the memory card with the ridge (2) on the connector.

4 Push the memory card straight into the connector, and then push the card toward the controller board wall until it clicks into place.

5 Close the controller board access cover.

Additional printer setup 31
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 27.
2 Unpack the optional card.
3 Holding the card by its sides, align the plastic pins (1) on the card with the holes (2) on the controller board.



Additional printer setup 32
4 Push the card firmly into place as shown in the illustration.

5 Close the controller board access door.

Additional printer setup 33
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Install the printer and any optional tray in the following order:
The printer supports two optional input sources: a 550‑sheet tray (Tray 3) and a 650‑sheet duo tray (Tray 2) with an integrated multipurpose feeder.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Unpack the optional tray and the dust cover, and then remove all packing material.

2 Place the tray near the printer.

Additional printer setup 34
3 Align the 650‑sheet duo tray with the 550‑sheet tray, and then lower it into place.

4 Align the printer with the 650‑sheet duo tray, and then lower the printer into place.


Additional printer setup 35
5 Install the dust covers.


Connect the printer to the computer using a USB cable or to the network using an Ethernet cable.
Make sure to match the following:

Additional printer setup 36

1 Rear USB port Attach an optional wireless network adapter or an optional printer hard disk.
2 Security lock port Lock the controller board.
3 Printer power cord socket
Connect the printer to a properly grounded electrical outlet.
4 LINE port Connect the printer to an active telephone line through a standard wall jack (RJ‑11), DSL filter, or VoIP adapter, or any other adapter that allows you to access the telephone line to send and receive faxes.
5 EXT port Connect additional devices (telephone or answering machine) to the printer and the telephone line. Use this port if you do not have a dedicated fax line for the printer and if this connection method is supported in your country or region.
6 USB printer port Connect the printer to a computer using a USB cable.
7 Ethernet port Connect the printer to an Ethernet network.
Use the To

Additional printer setup 37
2 Double‑click the software installer package.
Wait for the installation dialog to appear.
If you are using a Software and Documentation CD and the installation dialog does not appear, then do the following:
From the Search charm, type run, and then navigate to:
Apps list > Run > type D:\setup.exe > OK.
or click Start, and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
c Press Enter, or click OK.
Click the CD icon on the desktop.
3 Click Install, and then follow the instructions on the computer screen.
When any hardware options are installed, you may need to manually add the options in the printer driver to make them available for use.
1 Open the printers folder.
From the Search charm, type run, and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
a Click · In Windows 8 · a Click

Additional printer setup 38
4 Click the Configuration tab.
6 Click Apply.
2 Add any installed hardware options, and then click OK.
To configure your printer to connect to an Ethernet network, organize the following information before you begin:

Additional printer setup 39
You will need an Ethernet cable to connect the printer to the network and an available port where the printer can physically connect to the network. Use a new network cable when possible to avoid potential problems caused by a damaged cable.
2 Double‑click the software installer package.
Wait for the installation dialog to appear.
If you are using the Software and Documentation CD and the installation dialog does not appear, then do the following:
From the Search charm, type run, and then navigate to:
Apps list > Run > type: D:\setup.exe > OK
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
c Press Enter, or click OK.
3 Click Install, and then follow the instructions on the computer screen.
4 Select Ethernet connection, and then click Continue.
5 Attach the Ethernet cable when instructed to do so.
6 Select the printer from the list, and then click Continue.
7 Follow the instructions on the computer screen.
1 Allow the network DHCP server to assign an IP address to the printer.
In Windows 8 · a Click

Additional printer setup 40
3 Install the printer driver on the computer. a Insert the Software and Documentation CD, and then double‑click the installer package for the printer. b Follow the instructions on the computer screen.
c Select a destination, and then click Continue. d From the Easy Install screen, click Install. e Type the user password, and then click OK.
All the necessary applications are installed on the computer. f Click Close when installation is complete.
4 Add the printer. • For IP printing: a From the Apple menu, navigate to either of the following:
– System Preferences > Print & Scan – System Preferences > Print & Fax b Click +.
c Click the IP tab. d Type the printer IP address in the address field, and then click Add. • For AppleTalk printing:
– Make sure AppleTalk is activated on your printer. – This feature is supported only in Mac OS X version 10.5. a From the Apple menu, navigate to:
System Preferences > Print & Fax b Click +, and then navigate to:
AppleTalk > select your printer > Add
Make sure you have the following information before setting up the printer on a wireless network:
Some ad hoc networks will also require the automatic setting. Check with your system support person if you are not sure which channel to select.

Additional printer setup 41
If your network uses more than one WEP key, then enter up to four in the provided spaces. Select the key currently in use on the network by selecting the default WEP transmit key. – WPA or WPA2 preshared key or passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network. – 802.1X–RADIUS
If you are installing the printer on an 802.1X network, then you may need the following:
If your wireless network does not use any type of security, then you will not have any security information.
– If you do not know the SSID of the network that your computer is connected to, then launch the wireless utility
of the computer network adapter, and then look for the network name. If you cannot find the SSID or the security information for your network, then see the documentation that came with the access point, or contact your system support person. – To find the WPA/WPA2 preshared key or passphrase for the wireless network, see the documentation that
came with the access point, see the Embedded Web Server associated with the access point, or consult your system support person.
Before you begin, make sure that:
> Network/Ports > Active NIC > Auto >
1 From the printer control panel, navigate to:
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wireless Connection Setup
2 Select a wireless connection setup.

Additional printer setup 42
Search for networks Show available wireless connections.
Enter a network name Manually type the SSID.
Wi‑Fi Protected Setup Connect the printer to a wireless network using Wi‑Fi Protected Setup.
3 Follow the instructions on the printer display.
Connecting the printer to a wireless network using Wi‑Fi Protected Setup
Before you begin, make sure that:
1 From the printer control panel, navigate to:
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wireless Connection Setup > Wi‑Fi Protected Setup > Start Push Button Method
2 Follow the instructions on the printer display.
1 From the printer control panel, navigate to:
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wireless Connection Setup > Wi‑Fi Protected Setup > Start PIN Method
2 Copy the eight‑digit WPS PIN.
3 Open a Web browser, and then type the IP address of your access point in the address field.
4 Access the WPS settings. For more information, see the documentation that came with your access point.
5 Enter the eight‑digit PIN, and then save the setting.
Use To

Additional printer setup 43
Before you begin, make sure that:
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Network/Ports > Wireless.
3 Modify the settings to match the settings of your access point (wireless router).
4 Click Submit.
5 Turn off the printer, and then disconnect the Ethernet cable. Then wait for at least five seconds, and then turn the printer back on.
6 To verify if your printer is connected to the network, print a network setup page. Then in the Network Card [x] section, see if the status is Connected.
When all hardware and software options are installed and the printer is turned on, verify that the printer is set up correctly by printing the following:
From the home screen, navigate to:
> Reports > Menu Settings Page

Additional printer setup 44
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the home screen, navigate to:
> Reports > Network Setup Page
2 Check the first section of the network setup page, and confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult a system support person for a solution, and then print another network setup page.

Loading paper and specialty media 45
This chapter covers the selection and handling of paper and specialty media. Proper selection and loading of media can improve how reliably documents print. For more information, see “Avoiding jams” on page 240 and “Storing paper” on page 60.
From the home screen navigate to:
> Paper Menu > Paper Size/Type > select a tray > select the paper size or type >
The Universal paper size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus.
1 From the home screen, navigate to:
> Paper Menu > Universal Setup > Units of Measure > select a unit of measure
2 Touch Portrait Width or Portrait Height.
3 Select the width or height, and then touch
The printer has one 250-sheet tray (Tray 1) with an integrated manual feeder. The 250-sheet tray, the 650-sheet duo tray, and the 550-sheet tray support the same paper sizes and types and are loaded in the same way.
1 Pull out the tray completely.

Loading paper and specialty media 46

2 If the paper is longer than letter‑size paper, then squeeze and then slide the length guide at the back of the tray to extend it.


3 Squeeze, and then slide the length guide tab to the correct position for the size of the paper being loaded.


Loading paper and specialty media 47
4 Squeeze, and then slide the width guide tab to the correct position for the size of the paper being loaded.

5 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

6 Load the paper stack with the recommended printable side faceup.


7 Place the paper guides securely against the edges of the paper.

Loading paper and specialty media 48
8 Insert the tray.

9 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.
The standard 250‑sheet tray has an integrated manual feeder that can be used to print on different types of paper one sheet at a time.
One‑sided printing using a letterhead Two‑sided printing using a letterhead

ABC

2 Feed paper into the manual feeder only to the point where its leading edge can contact the paper guides.
3 Adjust the paper guides to the width of the paper loaded.

Loading paper and specialty media 49


The 650‑sheet duo tray (Tray 2) consists of a 550‑sheet tray and an integrated 100‑sheet multipurpose feeder. The tray is loaded in the same way as the 250‑sheet tray and the optional 550‑sheet tray, and supports the same paper types and sizes. The only differences are the look of the guide tabs and the location of the paper size indicators.

1 Length guide tab
2 Paper size indicator
3 Width guide tab

Loading paper and specialty media 50
1 Push the multipurpose feeder latch to the left.


2 Open the multipurpose feeder.

3 Pull the multipurpose feeder extender.


Loading paper and specialty media 51
4 Prepare the paper for loading. • Flex the sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Locate the maximum paper fill indicator and tab.


Loading paper and specialty media 52
5 Paper size indicator
6 Load the paper, and then adjust the width guide to lightly touch the edge of the paper stack. • Load paper, card stock, and transparencies with the recommended printable side facedown and the top edge entering the printer first.


7 From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
When the paper size and paper type for any trays are the same, the printer links those trays. When one linked tray becomes empty, paper feeds from the next linked tray. We recommend giving all unique paper, such as letterhead and different colored plain papers, a different custom type name so that the trays they are in do not automatically link.
1 Open a Web browser, and then type the printer IP address in the address field.

Loading paper and specialty media 53
2 Click Settings > Paper Menu.
4 Click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Select a custom name, and then type a custom paper type name.
4 Click Submit.
5 Click Custom Types, and then verify if the new custom paper type name has replaced the custom name.
1 From the home screen, navigate to:
> Paper Menu > Custom Names
2 Select a custom name, and then type a custom paper type name.
4 Touch Custom Types, and then verify that the new custom paper type name has replaced the custom name.
3 Touch

Loading paper and specialty media 54
Assign a custom paper type name to a tray when linking or unlinking trays.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Types.
3 Select a custom paper type name, and then select a paper type
4 Click Submit.
1 From the home screen, navigate to:
> Paper Menu > Custom Types
2 Select a custom paper type name, and then select a paper type
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Types.
3 Select a custom name you want to configure, then select a paper or specialty media type, and then click Submit.
1 From the home screen, navigate to:
> Paper Menu > Custom Types
2 Select a custom name you want to configure, and then touch
3 Touch

Paper and specialty media guide 55
Using specialty media
Source Printing Printable side Paper orientation
One‑sided Faceup Load the sheet with the top edge entering the printer first.

Two‑sided Facedown Load the sheet with the bottom edge entering the printer first.

One‑sided Facedown Load the sheet with the top edge entering the printer first.
Trays · Trays · Manual feeder

Paper and specialty media guide 56
Source Printing Printable side Paper orientation
Two‑sided Faceup Load the sheet with the bottom edge entering the printer first.
One‑sided Facedown Load the sheet with the top edge entering the printer first.
Two‑sided Faceup Load the sheet with the bottom edge entering the printer first.

Print a test page on the transparencies being considered for use before buying large quantities.
Manual feeder · Multipurpose feeder · Multipurpose feeder

Paper and specialty media guide 57

Paper and specialty media guide 58
Card stock is heavy, single‑ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly affect print quality.
Select the correct paper or specialty media to reduce printing problems. For the best print quality, try a sample of the paper or specialty media before buying large quantities.
The following paper characteristics affect print quality and reliability. Consider these characteristics when evaluating new paper stock.
The printer trays can automatically feed paper weights up to 176‑g/m2 (47‑lb) bond grain long paper. The multipurpose feeder can automatically feed paper weights up to 176‑g/m2 (47‑lb) bond grain long paper. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 75‑g/m2 (20‑lb) bond grain long paper. For paper smaller than 182 x 257 mm (7.2 x 10.1 inches), we recommend 90 g/m2 (24 lb) or heavier paper.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.
Paper smoothness directly affects print quality. If paper is too rough, then toner cannot fuse to it properly. If paper is too smooth, then it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; smoothness between 150 and 250 Sheffield points produces the best print quality.

Paper and specialty media guide 59
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.
Store paper in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extend the time to several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60–90‑g/m2 (16–24‑lb) bond paper, grain long paper is recommended.
Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton can negatively affect paper handling.
The following paper types are not recommended for use with the printer:
Using the appropriate paper prevents jams and helps ensure trouble‑free printing.
To help avoid paper jams and poor print quality:

Paper and specialty media guide 60
Use these guidelines when selecting preprinted forms and letterhead:
Use inks that are not affected by the resin in toner. Inks that are oxidation‑set or oil‑based generally meet these requirements; latex inks might not.
When in doubt, contact your paper supplier.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser (electrophotographic) printers. In 1998, Lexmark presented to the US government a study demonstrating that recycled paper produced by major mills in the US fed as well as non-recycled paper. However, no blanket statement can be made that all recycled paper will feed well.
Lexmark consistently tests its printers with recycled paper (20–100% post-consumer waste) and a variety of test paper from around the world, using chamber tests for different temperature and humidity conditions. Lexmark has found no reason to discourage the use of today's recycled office papers, but generally the following property guidelines apply to recycled paper.
Recycled paper, paper of lower weight (
Use these paper storage guidelines to help avoid jams and uneven print quality:

Paper and specialty media guide 61
This chapter provides information on standard and optional paper sources and the types of paper they support.
Note: Your printer model may have a 650‑sheet duo tray, which consists of a 550‑sheet tray and an integrated 100‑sheet multipurpose feeder. The 550‑sheet tray of the 650‑sheet duo tray supports the same paper sizes as the optional 550‑sheet tray. The integrated multipurpose feeder supports different paper sizes, types, and weights.
Paper size and dimension
Standard 250‑sheet tray
650‑sheet duo tray 550‑sheet tray
mode 550‑sheet tray
1
210 x 297 mm (8.3 x 11.7 in.)
1 2 1 2 X
148 x 210 mm (5.83 x 8.3 in.)
X X 1 X X X
105 x 148 mm (4.1 x 5.8 in.)
1 1 1 1 X
182 x 257 mm (7.2 x 10.1 in.)
Letter 216 x 279 mm (8.5 x 11 in.)
1
216 x 356 mm (8.5 x 14 in.)
1 The paper source supports paper size without size sensing.
2 Universal is supported in the standard 250‑ and optional 550‑sheet trays only if the paper size is from 148 x 215.9 mm (5.83 x 8.5 in.) to 215.9 x 355.6 mm (8.5 x 14 in.).
3 Universal is supported in the multipurpose feeder and manual feeder only if the paper size is from 76.2 x 127 mm (3 x 5 in.) to 215.9 x 359.9 mm (8.5 x 14.17 in.).
4 Universal is supported in duplex mode only if the width is from 210 mm (8.27 in.) to 215.9 mm (8.5 in.), and the length is from 279.4 mm (11 in.) to 355.6 mm (14 in.).

Paper and specialty media guide 62
Paper size and dimension
Standard 250‑sheet tray
650‑sheet duo tray 550‑sheet tray
mode 550‑sheet tray
184 x 267 mm (7.3 x 10.5 in.)
216 x 340 mm (8.5 x 13.4 in.)
216 x 330 mm (8.5 x 13 in.)
140 x 216 mm (5.5 x 8.5 in.)
76 x 127 mm (3 x 5 in.) to 216 x 356 mm (8.5 x 14 in.)
Universal 148 x 210 mm (5.8 x 8.3 in) to 216 x 356 mm (8.5 x 14 in).
7 3/4 Envelope (Monarch)
98 x 191 mm (3.9 x 7.5 in.)
9 Envelope 98 x 225 mm (3.9 x 8.9 in.)
X X 1 X X X X
105 x 241 mm (4.1 x 9.5 in.)
1 The paper source supports paper size without size sensing.
2 Universal is supported in the standard 250‑ and optional 550‑sheet trays only if the paper size is from 148 x 215.9 mm (5.83 x 8.5 in.) to 215.9 x 355.6 mm (8.5 x 14 in.).
3 Universal is supported in the multipurpose feeder and manual feeder only if the paper size is from 76.2 x 127 mm (3 x 5 in.) to 215.9 x 359.9 mm (8.5 x 14.17 in.).
4 Universal is supported in duplex mode only if the width is from 210 mm (8.27 in.) to 215.9 mm (8.5 in.), and the length is from 279.4 mm (11 in.) to 355.6 mm (14 in.).

Paper and specialty media guide 63
Paper size and dimension
Standard 250‑sheet tray
650‑sheet duo tray 550‑sheet tray
mode 550‑sheet tray
110 x 220 mm (4.3 x 8.7 in.)
162 x 229 mm (6.4 x 9 in.)
176 x 250 mm (6.9 x 9.8 in.)
98 x 162 mm (3.9 x 6.3 in.) up to 176 x 250 mm (6.9 x 9.8 in.)
1 The paper source supports paper size without size sensing.
2 Universal is supported in the standard 250‑ and optional 550‑sheet trays only if the paper size is from 148 x 215.9 mm (5.83 x 8.5 in.) to 215.9 x 355.6 mm (8.5 x 14 in.).
3 Universal is supported in the multipurpose feeder and manual feeder only if the paper size is from 76.2 x 127 mm (3 x 5 in.) to 215.9 x 359.9 mm (8.5 x 14.17 in.).
4 Universal is supported in duplex mode only if the width is from 210 mm (8.27 in.) to 215.9 mm (8.5 in.), and the length is from 279.4 mm (11 in.) to 355.6 mm (14 in.).

Paper and specialty media guide 64

650‑sheet duo tray 550‑sheet tray

Printing forms
Use the Forms and Favorites application to quickly and easily access frequently used forms or other information that is regularly printed. Before you can use this application, first set it up on the printer. For more information, see “Setting up Forms and Favorites” on page 20.
1 From the printer home screen, navigate to:
Forms and Favorites > select the form from the list > enter the number of copies > adjust other settings
2 Depending on your printer model, touch
, or Submit.
1 From the printer control panel, set the paper type and size to match the paper loaded.
2 Send the print job:
a With a document open, click File > Print. b Click Properties, Preferences, Options, or Setup.
c Adjust the settings, if necessary. d Click OK > Print.
a Customize the settings in the Page Setup dialog:
1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the paper loaded. 3 Click OK. b Customize the settings in the Print dialog:
1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options. 2 From the print options pop‑up menus, adjust the settings, if necessary.
From the home screen, navigate to:
Printing 65 · ,

> Settings > Print Settings > Quality Menu > Print Mode > Black Only >
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the setting, and then click Submit.
1 From the home screen, navigate to:
> Settings > Print Settings > Quality Menu > Toner Darkness
2 Adjust the setting, and then touch
Max Speed and Max Yield let you choose between a faster print speed or a higher toner yield. Max Yield is the factory default setting.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Setup Menu.
3 From the Printer Usage list, select Max Speed or Max Yield.
4 Click Submit.
Printing 66

1 From the home screen, navigate to:
> Settings > Print Settings > Setup Menu
2 From the Printer Usage list, select Max Speed or Max Yield.
3 Touch Submit.
1 Insert a flash drive into the USB port.

Printing 67

2 From the printer control panel, touch the document you want to print.
3 Touch the arrows to get a preview of the document.
to specify the number of copies to be printed, and then touch Print.
Printing 68 · 4 Use · or

Recommended flash drives File type
Documents:
Images:
1 From the home screen, navigate to:
> Security > Confidential Print > select a print job type
Max Invalid PIN Limit the number of times an invalid PIN can be entered.
Confidential Job Expiration Hold print jobs in the computer until you enter the PIN from the printer control panel.
Repeat Job Expiration Print and store print jobs in the printer memory.
Verify Job Expiration Print one copy of a print job and hold the remaining copies. It lets you examine if the first copy is satisfactory or not. The print job is automatically deleted from the printer memory when all copies are printed.
Reserve Job Expiration Store print jobs for printing at a later time.
Printing 69 · Use To

1 With a document open, click File > Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click Print and Hold.
4 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
5 Click OK or Print.
1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2 From the print options or Copies & Pages pop‑up menu, choose Job Routing.
3 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
4 Click OK or Print.
1 Open a Web browser, and then type the printer IP address in the address field.
Printing 70 · 2 Touch

2 Click Configuration > Other Settings tab > Security > Confidential Print Setup.
4 Save the modified settings.
1 From the home screen, navigate to:
> Reports > Print Fonts
2 Touch PCL Fonts or PostScript Fonts.
A directory list shows the resources stored in a flash memory or in the printer hard disk.
From the home screen, navigate to:
> Reports > Print Directory
1 From the home screen, touch Cancel Jobs, or press on the keypad.
2 Touch the job you want to cancel, and then touch
3 Press on the keypad to return to the home screen.
1 Open the printers folder.
Printing 71

From the Search charm, type run, and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
2 Double‑click the printer icon.
3 Select the print job you want to cancel.
4 Click Delete.
2 From the printer window, select the print job you want to cancel, and then delete it.
Printing 72 · In Windows 8 · a Click

Use the scanner glass for single-page documents, book pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
Use the ADF for multiple‑page documents including two-sided (duplex) pages.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, press .
1 Load an original document faceup, short edge first into the ADF tray.
Copying 73 · ADF Scanner glass

2 Adjust the paper guides.
3 From the home screen, navigate to:
Copy > specify the copy settings > Copy It
1 Place an original document facedown on the scanner glass in the upper left corner.
2 From the home screen, navigate to:
Copy > specify the copy settings > Copy It
If you have more pages to scan, then place the next document on the scanner glass, and then touch Scan the next page.
3 Touch Finish the Job.
1 Place a photo facedown on the scanner glass in the upper left corner.
2 From the home screen, navigate to:
Copy > Content > Photo >
3 From the Content Source menu, select the appropriate setting that best matches the original photo.
5 Touch Finish the Job.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 From the home screen, navigate to:
Copy > Copy from > select the size of the original document
Copying 74 · 4 Touch · > Copy It

3 Navigate to:
Copy to > select the tray that contains transparencies > Copy It
If there are no trays that support transparencies, then navigate to:
Manual Feeder > select the size of the transparencies > Transparency
4 Load transparencies into the multipurpose feeder, and then touch Copy It.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 From the home screen, navigate to:
Copy > Copy from > select the size of the original document
3 Touch Copy to > Manual Feeder.
4 Place the letterhead faceup, top edge first into the multipurpose feeder.
5 Select the size of the letterhead, and then touch Letterhead > Copy It.
1 From the home screen, touch Copy.
2 Adjust the copy settings, and then touch Save As Shortcut.
3 Type a unique name for the shortcut, and then touch
4 Verify that the shortcut name is correct, and then touch OK.
If the shortcut name is incorrect, then touch Cancel, and then reenter the information.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
Copying 75

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Copy from > select the size of the original document
4 Navigate to:
Copy to > select a new size for the copy > Copy It
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Copy from > select the size of the original document
4 Touch Copy to, and then select the tray that contains the paper type you want to use.
5 Touch Copy It.
Use the ADF to copy original documents with different paper sizes. Depending on the paper sizes loaded and the “Copy to” and “Copy from” settings, each copy is either printed on mixed paper sizes (Example 1) or scaled to fit a single paper size (Example 2).
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
Copying 76

3 From the home screen, navigate to:
Copy > Copy from > Mixed Sizes > Copy to > Auto Size Match > Copy It
The scanner identifies the different paper sizes as they are scanned. Copies are printed on mixed paper sizes corresponding to the paper sizes of the original document.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Copy from > Mixed Sizes > Copy to > Letter > Copy It
The scanner identifies the different paper sizes as they are scanned, and then scales the mixed paper sizes to fit on the paper size selected.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Sides (Duplex) > select the preferred duplexing method
> Copy It.
Copies can be scaled from 25% to 400% of the original document size.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
Copying 77 · 4 Touch

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, touch Copy.
4 From the Scale area, touch
to enlarge or reduce your copies.
5 Touch Copy It.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:

> Copy It.
If you print multiple copies of a document, then you can choose to print the copies as a set (collated) or to print the copies as groups of pages (not collated).
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > enter the number of copies > Collate > select the preferred order of pages >
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Separator Sheets

> Copy It.
In order to save paper, you can copy either two or four consecutive pages of a multiple‑page document onto a single sheet of paper.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Paper Saver > select the output you want >
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
4 Select Header or Footer, and then touch
5 Select where you want to insert the header or footer, then select a text option, and then touch

6 Select where you want to print the header or footer, and then touch
7 From the Header/Footer menu, touch
> Copy It.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Overlay > select an overlay message >
4 Touch Copy It.
When the ADF begins processing a document, touch Cancel Job on the printer control panel.
From the home screen, touch Cancel Job.
Canceling appears on the display. When the job is canceled, the Copy screen appears.
1 From the printer control panel, press .
2 Touch the job you want to cancel, and then touch
3 Press to return to the home screen.
Copying 81

This option lets you select the paper size of the original document.
This option lets you select the size and type of paper on which your copies will be printed.
This option lets you scale the document from 25% to 400% of the original document size. You can also set automatic scaling.
on the printer control panel. To make a continuous decrease or increase in value, hold the button for two seconds or more.
This option lets you adjust how light or dark the copies are in relation to the original document.
This option lets you make one- or two-sided copies from one- or two-sided original documents.
This option keeps the pages of a print job stacked in sequence when printing multiple copies of the document.
This option lets you set the number of copies to be printed.
Copying 82 · or

This option lets you set the original document type and source.
Select from the following content types:
Select from the following content sources:
This option lets you set the output to either color or monochrome for the scanned image.
This option lets you specify the document orientation, whether documents are one-sided or two-sided, and how documents are bound.
This option lets you save the current settings by assigning a shortcut name.
This option lets you increase or reduce the size of the margin of a page by shifting the scanned image. Touch
to set the margin you want. If the additional margin is too large, then the copy will be cropped.
This option lets you remove smudges or marks around the edges of a document. You can choose to remove an equal area around all four sides of the paper, or pick a particular edge. Edge Erase also removes whatever is within the area selected, leaving nothing on that portion of the scan.
Copying 83 · or

This option lets you create a watermark (or message) that overlays the content of your copy. You can choose from Confidential, Copy, Draft, Urgent, and Custom. You can type a custom message in the ”Enter the Custom Text Overlay and press OK” field. The message will appear, faintly, in large print across each page.
This option lets you set up the cover page of copies and booklets.
This option lets you place a blank sheet of paper between copies, prints, pages, print jobs or copy jobs. The separator sheets can be drawn from a tray that contains a type or color of paper that is different from the paper your copies are printed on.
This option lets you insert a header or footer and specify its location on a page.
Select one of the following:
This option lets you print two or more pages of an original document on the same page. Paper Saver is also called N- up printing where N stands for the number of pages. For example, 2-up would print two pages of your document on a single page, and 4-up would print four pages of your document on a single page.
This option lets you adjust the Auto Center, Background Removal, Color Balance, Color Dropout, Contrast, Mirror Image, Negative Image, Scan Edge to Edge, Shadow Detail, Sharpness, and Temperature settings before you copy the document.
This option lets you create a sequence of printed and collated pages that, when folded, forms a booklet half the page size of the original document and with all the pages in order. You can choose between one‑sided and two‑sided.
This option lets you combine multiple scan jobs into a single job and appears only when a working printer hard disk is installed.
Copying 84

Use the scanner glass for single-page documents, book pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
Use the ADF for multiple‑page documents including two-sided (duplex) pages.
You can use the printer to e‑mail scanned documents to one or more recipients. There are three ways to send an e‑mail from the printer. You can type the e‑mail address, use a shortcut number, or use the address book.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > E-mail/FTP Settings > E-mail Settings.
3 Enter the appropriate information, and then click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
E-mailing 85 · ADF Scanner glass

2 Click Settings.
3 From the Other Settings column, click Manage Shortcuts > E-mail Shortcut Setup.
4 Type a unique name for the e‑mail recipient, and then type the e‑mail address. If you are entering multiple addresses, then separate each address with a comma.
5 Click Add.
1 From the home screen, navigate to:
E-mail > Recipient(s) > type the recipient’s e‑mail address >
, and then type the next recipient’s e-mail address.
2 Touch Subject > type the e‑mail subject >
3 Touch Message > type your message >
4 Adjust the e‑mail settings.
5 Touch Save As Shortcut.
6 Type a unique name for the shortcut, and then touch
7 Verify that the shortcut name is correct, and then touch OK.
If the shortcut name is incorrect, then touch Cancel, and then reenter the information.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
E-mailing 86

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
4 Type the e‑mail address, or press # and then enter the shortcut number.
, and then enter the e‑mail address or shortcut number that you want to add.
To enter additional recipients, touch
> E‑mail It.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 Press #, then enter the shortcut number using the keypad, and then touch
, and then enter the e‑mail address or shortcut number that you want to add.
To enter additional recipients, touch
> E‑mail It.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
E-mail > Recipient(s) >
> type the name of the recipient >

4 Touch the name of the recipient.
To search for additional recipients, touch New Search, and then type the name of the next recipient.
> E‑mail It.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
E-mail > Recipient(s) > type the e‑mail address >
4 Touch Subject > type the e‑mail subject >
5 Touch Message > type your message >
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
E-mail > Recipient(s) > type the e‑mail address >
E-mailing 88 · 5 Touch · > Send as

> E‑mail It.
This option lets you enter the recipient of your e-mail. You may enter multiple e‑mail addresses.
This option lets you type a subject line for your e-mail.
This option lets you type a message that will be sent with your scanned attachment.
This option lets you customize the attachment file name.
This option lets you save the current settings as a shortcut by assigning a shortcut name.
This option lets you set the paper size of the documents you are going to e‑mail. When Original Size is set to Mixed Sizes, you can scan an original document that contains mixed paper sizes (letter‑ and legal‑size pages).
E-mailing 89 · 5 Touch

This option lets you adjust how light or dark your scanned documents are in relation to the original document.
This option lets you adjust the output quality of your e-mail. Increasing the image resolution increases the e-mail file size and the time needed to scan your original document. Decreasing the image resolution reduces the file size.
This option lets you set the output to either color or monochrome for the scanned image.
This option lets you set the output type for the scan image.
Select one of the following:
This option lets you set the original document type and source.
Select from the following content types:
Select from the following content sources:
E-mailing 90

This option lets you change the following settings:
This option lets you combine multiple scan jobs into a single job and appears only when a working printer hard disk is installed.
This option lets you view the first page of the image before it is included in the e-mail. When the first page is scanned, the scanning is paused and a preview image appears.
This option lets you print the transmission log or transmission error log.
This option lets you remove smudges or any mark around the edges of a document. You can remove an equal area around all four sides of the paper, or you can pick a particular edge. Edge Erase also removes whatever is within the area selected, leaving nothing on that portion of the scan.
This option lets you adjust the Background Removal, Color Balance, Color Dropout, Contrast, JPEG Quality, Mirror Image, Negative Image, Scan Edge to Edge, Shadow Detail, Sharpness, and Temperature settings before you e‑mail the document.
E-mailing 91

Automatic document feeder (ADF) Scanner glass
Use the scanner glass for single-page documents, book pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
Use the ADF for multiple‑page documents including two- sided (duplex) pages.
During the initial printer setup, clear the Fax funtion and any other function you plan to set up later, and then press Continue.
Faxing 92


Many countries and regions require outgoing faxes to contain the following information in a margin at the top or bottom of each transmitted page, or on the first page of the transmission: fax name (identification of the business, other entity, or individual sending the message) and fax number (telephone number of the sending fax machine, business, other entity, or individual). For more information, see “Regulatory notices for telecommunication terminal equipment” on page 327.
To enter your fax setup information, use the printer control panel, or use your browser to access the Embedded Web Server and then enter the Settings menu.
When the printer is turned on for the first time, a series of start‑up screens appear. If the printer has fax capabilities, then the Fax Name and Fax Number screens appear.
1 When the Fax Name screen appears, do the following: a Enter the name to be printed on all outgoing faxes. b Enter the fax name, and then touch Submit.
2 When the Fax Number screen appears, enter the fax number, and then touch Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Fax Settings > Analog Fax Setup.
3 In the Fax Name field, type the name to be printed on all outgoing faxes.
Faxing 93

4 In the Fax Number field, enter the printer fax number.
5 Click Submit.
Setup 1: Printer is connected to a dedicated fax line


To connect:
1 Connect one end of the telephone cable that came with the printer to the port of the printer.
2 Connect the other end of the telephone cable to an active analog wall jack.
Faxing 94

Connected to the same telephone wall jack

To connect:
1 Connect one end of the telephone cable that came with the printer to the port of the printer.
2 Connect the other end of the telephone cable to an active analog wall jack.
3 Connect the answering machine to the port of the printer.
Faxing 95

Connected to different wall jacks

To connect:
1 Connect one end of the telephone cable that came with the printer to the port of the printer.
2 Connect the other end of the telephone cable to an active analog wall jack.
Faxing 96


To connect:
1 Connect one end of the telephone cable that came with the printer to the port of the printer.
2 Connect the other end of the telephone cable to an active analog wall jack.
3 Connect the telephone to the port of the printer.
When you answer the telephone and you hear fax tones, press *9* or the manual answer code on the telephone to receive the fax. • You can also set the printer to receive faxes automatically (Auto Answer On), but you need to turn off the voice mail service when you are expecting a fax. This setting works best if you are using voice mail more often than fax.
Faxing 97


A Digital Subscriber Line splits your regular telephone line into two channels: voice and Internet. Telephone and fax signals travel through the voice channel, and Internet signals pass through the other channel. This way, you can use the same line for analog voice calls (including faxes) and digital Internet access.
To minimize interference between the two channels and ensure a quality connection, you need to install a DSL filter for the analog devices (fax machine, telephone, answering machine) in your network. Interference causes noise and static on the telephone, failed and poor quality faxes for the printer, and slow Internet connection on your computer.
To install a filter for the printer:
1 Connect the line port of the DSL filter to the wall jack.
2 Connect one end of the telephone cable that came with your printer to the port of the printer. Connect the other end to the phone port on the DSL filter.
3 To continue using a computer for Internet access, connect the computer to the DSL HPN port on the DSL filter.
4 To connect a telephone to the printer, remove any installed adapter plug from the port of the printer, and then connect the telephone to the port.
Faxing 98



To connect:
1 Connect one end of the telephone cable that came with the printer to the port of the printer.
2 Connect the other end of the cable to the port labeled Phone Line 1 or Phone Port on the VoIP adapter.
3 Connect the telephone to the port of the printer.
Faxing 99

Setup 1: Printer is connected directly to a cable modem

1 Connect one end of the telephone cable that came with your printer to the port of the printer.
2 Connect the other end of the cable to the port labeled Phone Line 1 or Phone Port on the cable modem.
3 Connect your analog telephone phone to the port of the printer.
Faxing 100

Setup 2: Printer is connected to a wall jack; cable modem is installed elsewhere in the facility


1 Connect one end of the telephone cable that came with your printer to the port of the printer.
2 Connect the other end of the telephone cable to an active analog telephone wall jack.
3 Connect your analog telephone to the port of the printer.
Some countries or regions may have different types of telephone wall jack connectors than those that came with the printer. The standard wall jack adopted by most countries or regions is RJ-11. Your printer comes with the RJ-11 jack and a telephone cable with the RJ-11 plug.
Faxing 101

If the wall jack or equipment in your facility is not compatible with this type of connection, then you need to use a telephone adapter. An adapter for your country or region may not come with your printer, and you may need to purchase it separately.
There may be an adapter plug installed in the port of the printer. If you are using a telephone adapter or a facility that has a cascaded or serial wiring scheme, then do not remove the adapter plug from the port of the printer.
Part name Part number
Lexmark adapter plug 40X8519
Faxing 102

Connecting the printer to a non‑RJ‑11 wall jack

1 Connect one end of the telephone cable that came with printer to the port of the printer.
2 Connect the other end of the cable to the RJ‑11 adapter, and then connect the adapter to the wall jack.
3 If you want to connect another device (telephone or answering machine) to the same wall jack, and if the device has a non‑RJ‑11 connector, then connect it directly to the telephone adapter.
Faxing 103

The German wall jack has two kinds of ports. The N ports are for fax machines, modems, and answering machines. The F port is for telephones.

Connect the printer to any of the N ports.

1 Connect one end of the telephone cable that came the printer to the port of the printer.
2 Connect the other end of the telephone cable to the RJ‑11 adapter, and then connect the adapter to an N port.
Faxing 104

3 If you want to connect a telephone and answering machine to the same wall jack, then connect the devices as shown.
A distinctive ring service may be available from your telephone company. This service lets you have multiple telephone numbers on one telephone line, with each telephone number having a different ring pattern. This may be useful for distinguishing between fax and voice calls. If you subscribe to a distinctive ring service, then follow these steps to connect the equipment:
1 Connect one end of the telephone cable that came with the printer to the printer LINE port .
2 Connect the other end of the telephone cable to an active analog telephone wall jack.

3 Change the distinctive rings setting to match the setting you want for the printer to answer.
> Settings > Fax Settings > Analog Fax Setup > Answer On
b Select the pattern setting you want to change, and then touch
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Fax Settings > Analog Fax Setup.
3 In the Fax Name field, type the name to be printed on all outgoing faxes.
Faxing 105

4 In the Fax Number field, enter the printer fax number.
5 Click Submit.
You can set the date and time so that they are printed on every fax you send.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Security > Set Date and Time.
3 In the Manually Set Date & Time field, enter the current date and time.
4 Click Submit.
The printer can be set to automatically adjust for daylight saving time:
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Security > Set Date and Time.
3 Select the Automatically Observe DST check box, and then enter the DST start and end dates in the Custom Time Zone Setup section.
4 Click Submit.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
Faxing 106

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, touch Fax.
4 From the printer control panel keypad, enter the fax number or the shortcut number.
, and then enter the recipient's telephone number or shortcut number, or search the address book.
5 Touch Fax It.
The printer driver fax option lets you send a print job to the printer, which sends the job as a fax. The fax option works as a normal fax machine, but is controlled through the printer driver instead of the printer control panel.
1 With a document open, click File > Print.
2 Select the printer, and then click Properties, Preferences, Options, or Setup.
3 Navigate to:
Fax tab > Enable fax
4 Enter the recipient fax number or numbers in the “Fax number(s)” field.
5 If necessary, enter a prefix in the “Dialing prefix” field.
6 Select the appropriate paper size and page orientation.
7 If you want to include a cover page with the fax, then select Include cover page with fax, and then enter the appropriate information.
8 Click OK.
Fax shortcuts are like the speed dial numbers on a telephone or a fax machine. A shortcut number (1–999) can contain a single recipient or multiple recipients.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
Faxing 107

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, press #, and then enter the shortcut number using the keypad.
4 Touch Fax It.
The address book feature lets you search for bookmarks and network directory servers.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
> type the name of the recipient >
4 Touch the name of the recipient, and then touch Fax It.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
Fax > enter the fax number > Delayed Send
Faxing 108 · Fax >

4 Specify the time the fax will be transmitted, and then touch
The time is increased or decreased in 30‑minute increments.
5 Touch Fax It.
Assign a shortcut number to a single fax number or a group of fax numbers.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Manage Shortcuts > Fax Shortcut Setup.
3 Type a name for the shortcut, and then enter the fax number.
4 Assign a shortcut number.
5 Click Add.
1 From the home screen, touch Fax, and then enter the fax number.
To create a group of fax numbers, touch
, and then enter the other fax number.
3 Type a unique name for the shortcut, and then touch
4 Verify that the shortcut name and number are correct, and then touch OK.
If the name or number is incorrect, then touch Cancel, and then reenter the information.
Faxing 109 · 2 Touch

1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, touch Fax, and then enter the fax number.
4 From the Resolution area, touch
to change to the resolution you want.
5 Touch Fax It.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, touch Fax, and then enter the fax number.
4 From the Darkness area, touch
to adjust the darkness setting of the fax.
5 Touch Fax It.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Reports.
3 Click Fax Job Log or Fax Call Log.
Faxing 110 · or · or

1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Fax Settings > Analog Fax Setup > Block No Name Fax.
1 On the home screen, touch Cancel Jobs.
The Cancel Jobs screen appears.
2 Touch the job or jobs you want to cancel.
Only three jobs appear on the screen; touch the down arrow until the job you want appears, and then touch the job you want to cancel.
3 Touch Delete Selected Jobs.
The Deleting Selected Jobs screen appears, the selected jobs are deleted, and then the home screen appears.
This option lets you hold received faxes from printing until they are released. Held faxes can be released manually or at a scheduled day or time.
1 Open a Web browser, and then type the printer IP address in the address field.
Faxing 111

2 Click Settings > Fax Settings > Analog Fax Setup > Holding Faxes.
4 If you selected Scheduled, then continue with the following steps: a Click Fax Holding Schedule. b From the Action menu, select Hold faxes.
c From the Time menu, select the time you want the held faxes released. d From the Day(s) menu, select the day you want the held faxes released.
5 Click Add.
This option lets you print and forward received faxes to a fax number, e‑mail address, FTP site, or LDSS.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Fax Settings.
3 From the Fax Forwarding menu, select Print, Print and Forward, or Forward.
4 From the “Forward to” menu, select Fax, E‑mail, FTP, LDSS, or eSF.
5 In the “Forward to Shortcut” field, enter the shortcut number where you want the fax forwarded.
6 Click Submit.
This option lets you adjust how light or dark the faxes are in relation to the original document.
Faxing 112

This option lets you adjust the quality of the fax output. Increasing the image resolution increases the file size and the time needed to scan your original document. Decreasing the image resolution reduces the file size.
Select one of the following:
This option lets you set the output to either color or monochrome for the scanned image.
This option lets you specify the content type and source of the original document.
Select from the following content types:
Select from the following content sources:
This option lets you change the following settings:
Faxing 113

This option lets you print the transmission log or transmission error log.
This option lets you remove smudges or any mark around the edges of a document. You can remove an equal area around all four sides of the paper, or you can pick a particular edge. Edge Erase also removes whatever is within the area selected, leaving nothing on that portion of the scan.
This option lets you combine multiple scan jobs into a single job and appears only when a working printer hard disk is installed.
This option lets you view the first page of the image before it is included in the fax. When the first page is scanned, the scanning is paused and a preview image appears.
This option lets you send a fax at a later time or date.
This option lets you change or adjust the Background Removal, Color Balance, Color Dropout, Contrast, Mirror Image, Negative Image, Scan Edge to Edge, Shadow Detail, and Sharpness settings before you fax the document.
Faxing 114

Using Scan to Network
Scan to Network lets you scan your documents to network destinations specified by your system support person. After the destinations (shared network folders) have been established on the network, the setup process for the application involves installing and configuring the application on the appropriate printer using its Embedded Web Server. For more information, see “Setting up Scan to Network” on page 23.
Automatic document feeder (ADF) Scanner glass
Use the ADF for multiple‑page documents including two- sided (duplex) pages.
Use the scanner glass for single-page documents, book pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
The scanner lets you scan documents directly to a File Transfer Protocol (FTP) server. Only one FTP address may be sent to the server at a time.
When an FTP destination has been configured by your system support person, the name of the destination becomes available as a shortcut number, or it is listed as a profile under the Held Jobs icon. An FTP destination could also be another PostScript printer.
Instead of entering the entire FTP site address on the printer control panel each time you want to send a document to an FTP server, you can create a permanent FTP destination and assign a shortcut number. There are two methods for creating shortcut numbers: using the Embedded Web Server or using the printer control panel.
1 Open a Web browser, and then type the printer IP address in the address field.
Scanning 115

2 Navigate to:
Settings > Other Settings area > Manage Shortcuts > FTP Shortcut Setup
3 Enter the appropriate information.
4 Enter a shortcut number.
5 Click Add.
1 From the home screen, navigate to:
FTP > FTP Address > type the FTP address >
> type a name for the shortcut >
2 Verify that the shortcut name and number are correct, and then touch OK.
If the name or number is incorrect, then touch Cancel, and then reenter the information. If you enter a number that is already in use, then you will be prompted to select another number.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the home screen, navigate to:
FTP > FTP Address > type the FTP address >
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
Scanning 116 · > · > Scan It

2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 From the printer control panel, press # on the keypad, and then enter the FTP shortcut number.
4 Touch Scan It.
Use the ADF for multiple‑page documents. Use the scanner glass for single-page documents, small items (such as postcards
or photos), transparencies, photo paper, or thin media (such as magazine clippings).
The scanner lets you scan documents directly to a computer or a flash drive. The computer does not have to be directly connected to the printer for you to receive images when scanning to a computer. You can scan the document back to the computer over the network by creating a scan profile on the computer and then downloading the profile to the printer.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Scan Profile > Create Scan Profile.
3 Select your scan settings, and then click Next.
4 Select a location on your computer where you want to save the scan image.
Scanning 117 · ADF Scanner glass

5 Type a scan name, and then a user name.
6 Click Submit.
7 Review the instructions on the Scan Profile screen. a Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
c Do either of the following:
8 View the file from the computer.
1 Open the printers folder.
From the Search charm, type run, and then navigate to:
Apps list > Run > type control printers > OK
or click Start, and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
2 Depending on your operating system, click Add devices and printers, Add a device, or Add a printer.
3 Select your printer from the list.
Scanning 118 · a Click

4 Click Next > Close.
6 From the menu that appears, select Scan Properties or Properties, and then change the settings as necessary.
8 Touch Send It.
Remote scan in progress appears on the printer display. The scanned image opens automatically on the computer screen.
1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.
2 If you are loading a document into the ADF tray, then adjust the paper guides.
3 Insert the flash drive into the USB port on the front of the printer.
4 Select the destination folder, and then touch Scan to USB drive.
5 Adjust the scan settings, and then touch Scan It.
This option lets you enter the IP address for the FTP destination.
This option lets you type a file name for the scan image.
Scanning 119

This option lets you save the current settings as a shortcut by assigning a shortcut name.
This option lets you set the paper size of the documents you are going to scan. When Original Size is set to Mixed Sizes, you can scan an original document that contains mixed paper sizes (letter‑ and legal‑size pages).
This option lets you adjust how light or dark the scanned documents are in relation to the original document.
This option lets you adjust the output quality of your file. Increasing the image resolution increases the file size and the time needed to scan your original document. Decreasing the image resolution reduces the file size.
This option lets you set the output to either color or monochrome for the scanned image.
This option lets you set the output type for the scan image.
Select one of the following:
This option lets you set the original document type and source.
Select from the following content types:
Scanning 120

Select from the following content sources:
This option lets you change the following settings:
This option lets you print the transmission log or transmission error log.
This option lets you view the first page of the image before it is included in the file. When the first page is scanned, the scanning is paused and a preview image appears.
This option lets you remove smudges or any mark around the edges of a document. You can remove an equal area around all four sides of the paper, or you can pick a particular edge. Edge Erase also removes whatever is within the area selected, leaving nothing on that portion of the scan.
This option lets you adjust the Background Removal, Color Balance, Color Dropout, Contrast, JPEG Quality, Mirror Image, Negative Image, Scan Edge to Edge, Shadow Detail, and Sharpness settings before you scan the document.
This option lets you combine multiple scan jobs into a single job and appears only when a working printer hard disk is installed.
Scanning 121

Understanding printer menus 122
Menus list
Supplies Menu Paper Menu Reports Network/Ports
Cyan Cartridge Magenta Cartridge
Default Source Paper Size/Type
Menu Settings Page Device Statistics
Active NIC Standard Network or Network [x]
Network [x] Setup Page
E‑mail Shortcuts Fax Shortcuts
Custom Scan Sizes Universal Setup
Security Settings Help Manage Shortcuts Option Card Menu
[index of each installed DLE]
E‑mail Shortcuts
E‑mail Guide
Disk Wiping Security Audit Log
E‑mail Settings
Set Date and Time
Print Defects Guide Information Guide

Understanding printer menus 123
Cyan, Magenta, Yellow, or Black Toner Cartridge
Show the status of the cyan, magenta, yellow, or black toner cartridge.
Nearly Low Low Very Low Replace Missing Defective Missing or Unresponsive Unsupported Invalid Region OK Non‑genuine Lexmark Cartridge
Black or Color Imaging Kit
Show the status of the black or color imaging kit.
Nearly Low Low Very Low Replace Missing Defective Missing or Unresponsive Unsupported OK Non‑genuine Lexmark Imaging Kit
Show the status of the waste toner bottle.
Near Full Replace Missing OK
Show the status of the maintenance kit.
Nearly Low Low Very Low Replace OK
Use To · Waste Toner Bottle · Maintenance Kit

Understanding printer menus 124
Set a default paper source for all print jobs.
Tray [x] MP Feeder Manual Paper Manual Envelope
Specify the paper size loaded in each tray.
A4 A5 JIS‑B5 Letter Legal Executive Oficio (Mexico) Folio Universal
Specify the type of paper loaded in each tray.
Plain Paper Card Stock Transparency Recycled Labels Glossy Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]

Understanding printer menus 125
Specify the paper size loaded in the multipurpose feeder.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the paper type loaded in the multipurpose feeder.
Plain Paper Card Stock Transparency Recycled Glossy Labels Bond Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Use To · MP Feeder Size · MP Feeder Type

Understanding printer menus 126
Specify the size of the paper being manually loaded.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the paper type being manually loaded.
Plain Paper Card Stock Transparency Recycled Glossy Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Specify the envelope size being manually loaded.
7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the envelope type being manually loaded.
Envelope Custom Type [x]

Understanding printer menus 127
Substitute a specified paper size if the requested paper size is not available.
Off Statement/A5 Letter/A4 All Listed
Specify the relative texture of the plain paper loaded.
Specify the relative texture of the card stock loaded.
Specify the relative texture of the transparencies loaded.
Specify the relative texture of the recycled paper loaded.
Specify the relative texture of the glossy paper loaded.
Specify the relative texture of the heavy glossy paper loaded.
Specify the relative texture of the labels loaded.

Understanding printer menus 128
Specify the relative texture of the bond paper loaded.
Specify the relative texture of the envelopes loaded.
Specify the relative texture of the letterhead loaded.
Specify the relative texture of the preprinted paper loaded.
Specify the relative texture of the colored paper loaded.
Specify the relative texture of the light paper loaded.
Specify the relative texture of the heavy paper loaded.
Specify the relative texture of the cotton paper loaded.
Specify the relative texture of the custom paper loaded.

Understanding printer menus 129
Specify the relative weight of the plain paper loaded.
Specify the relative weight of the card stock loaded.
Specify the relative weight of the transparencies loaded.
Specify the relative weight of the recycled paper loaded.
Specify the relative weight of the glossy paper loaded.
Specify the relative weight of the heavy glossy paper loaded.
Specify the relative weight of the labels loaded.
Specify the relative weight of the bond paper loaded.
Specify the relative weight of the envelope loaded.
Specify the relative weight of the rough envelope loaded.

Understanding printer menus 130
Specify the relative weight of the letterhead loaded.
Specify the relative weight of the preprinted paper loaded.
Specify the relative weight of the colored paper loaded.
Specify that the relative weight of the paper loaded is light.
Specify that the relative weight of the paper loaded is heavy.
Specify the relative weight of the rough or cotton paper loaded.
Specify the relative weight of the custom paper loaded.
Determine and set two‑sided printing for all print jobs that specify Cardstock as the paper type.
Determine and set two‑sided printing for all print jobs that specify Recycled as the paper type.
Determine and set two‑sided printing for all print jobs that specify Glossy as the paper type.

Understanding printer menus 131
Determine and set two‑sided printing for all print jobs that specify Heavy Glossy as the paper type.
Determine and set two‑sided printing for all print jobs that specify Labels as the paper type.
Determine and set two‑sided printing for all print jobs that specify Bond as the paper type.
Determine and set two‑sided printing for all print jobs that specify Letterhead as the paper type.
Determine and set two‑sided printing for all print jobs that specify Preprinted as the paper type.
Determine and set two‑sided printing for all print jobs that specify Colored as the paper type.
Determine and set two‑sided printing for all print jobs that specify Light as the paper type.
Determine and set two‑sided printing for all print jobs that specify Heavy as the paper type.
Determine and set two‑sided printing for all print jobs that specify Rough/Cotton as the paper type.
Determine and set two‑sided printing for all print jobs that specify Custom [x] as the paper type.

Understanding printer menus 132
Associate a paper or specialty media type with a factory default Custom Type [x] name or a user‑defined custom name created in the Embedded Web Server or MarkVisionTM Professional.
Paper Card Stock Transparency Glossy Rough/Cotton Labels Envelope
Specify a paper type when Recycled is selected.
Paper Card Stock Transparency Glossy Rough/Cotton Labels Envelope
Custom Name [x] Specify a custom name for a paper type. This name replaces Custom Type [x] in the printer menus.
Custom Scan Size [x]
Specify a custom scan size name, scan sizes, and options.
Scan Size Name Width
1–8.5 inches (25–215.9 mm) Height
1–14 inches (25–355.6 mm) Orientation
Portrait Landscape 2 scans per side Off On

Understanding printer menus 133
Specify the unit of measure.
Set the width for portrait orientation.
3–8.5 inches 76–215.9 mm
Set the height for portrait orientation.
3–14.17 inches 76–360 mm
Menu Settings Page Print a report containing information about the paper loaded in trays, installed memory, total page count, alarms, timeouts, printer control panel language, TCP/IP address, status of supplies, status of the network connection, and other information.
Device Statistics Print a report containing printer statistics such as supply information and details about printed pages.
Network Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address.
Network [x] Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address.
![Page 134 of the Lexmark 415 user manual — Standard Network or Network [x] menus](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-134.webp?w=400)
Understanding printer menus 134
Shortcut List Print a report containing information about configured shortcuts.
Fax Job Log Print a report containing information about the last 200 completed faxes.
Fax Call Log Print a report containing information about the last 100 attempted, received, and blocked calls.
Copy Shortcuts Print a report containing information about copy shortcuts.
E‑mail Shortcuts Print a report containing information about e‑mail shortcuts.
Fax Shortcuts Print a report containing information about fax shortcuts.
FTP Shortcuts Print a report containing information about FTP shortcuts.
Profiles List Print a list of profiles stored in the printer.
Print Fonts Print a report of all the fonts available for the printer language currently set in the printer.
Print Directory Print a list of all the resources stored on an optional flash memory card or in printer hard disk.
Asset Report Print a report containing asset information including the printer serial number and model name. The report contains text and UPC barcodes that can be scanned into an asset database.
Allow the printer to connect to a network.
Auto [list of available network cards]
Use To · Use To · Active NIC

Understanding printer menus 135
Set the printer to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.
Set the size of the network input buffer.
Auto 3KB to [maximum size allowed]
Temporarily store print jobs in the printer hard disk before printing. This menu only appears when a formatted disk is installed.

Understanding printer menus 136
Set the printer to process Macintosh binary PostScript print jobs.
Standard Network Setup OR Network [x] Setup
Display and set the printer network settings.
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
To access the menu, navigate to either of the following:
Print Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address.
To access the menu, navigate to either of the following:
View the connection status of the network card.
View Card Speed View the speed of an active network card.
View the network addresses.

Understanding printer menus 137
Set the amount of time it takes for a network print job to be canceled.
To access the menu, navigate to either of the following:
Set Hostname Set the current TCP/IP host name.
IP Address View or change the current TCP/IP address.
Netmask View or change the current TCP/IP netmask.
Gateway View or change the current TCP/IP gateway.
Specify the DHCP address and parameter assignment.
Specify the RARP address assignment setting.
Specify the BOOTP address assignment setting.
Specify the Zero Configuration Networking setting.
Enable the built-in FTP server, which lets you send files to the printer using File Transfer Protocol.
Enable the built-in Web server (Embedded Web Server). When enabled, the printer can be monitored and managed remotely using a Web browser.

Understanding printer menus 138
WINS Server Address View or change the current WINS server address.
View or change the current DDNS setting.
View or change the current mDNS setting.
DNS Server Address View or change the current DNS server address.
Backup DNS Server Address View or change the backup DNS server addresses.
Backup DNS Server Address 2
Backup DNS Server Address 3
View or change the current HTTPS setting.
To access the menu, navigate to any of the following:
Enable IPv6 in the printer.
Specify whether or not the network adapter accepts the automatic IPv6 address configuration entries provided by a router.
Set Hostname Set the host name.
Enable DHCPv6 in the printer.

Understanding printer menus 139
To access the menu, navigate to:
Network/Ports > Network [x] > Network [x] Setup > Wireless
Wi‑Fi Protected Setup
Establish a wireless network and enable network security.
Start Push Button Method Start PIN Method
Enable/Disable WPS Auto‑detection
Automatically detect the connection method that an access point with WPS uses—Start Push Button Method or Start PIN Method.
Specify the network mode.
Specify the wireless standard for the wireless network.
802.11b/g 802.11b/g/n
Choose Network Select an available network for the printer to use.
View Signal Quality View the quality of the wireless connection.
View Security Mode View the encryption method for the wireless network.
To access the menu, navigate to either of the following:
Enable or disable AppleTalk support.
View Name Show the assigned AppleTalk name.

Understanding printer menus 140
View Address Show the assigned AppleTalk address.
Provide a list of AppleTalk zones available on the network.
[list of zones available on the network]
Set the printer to automatically switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.

Understanding printer menus 141
Set the size of the USB input buffer.
Disabled Auto 3K to [maximum size allowed]
Set the printer to process Macintosh binary PostScript print jobs.
Set the network address information for an external print server.
yyy.yyy.yyy.yyy
Set the netmask information for an external print server.
yyy.yyy.yyy.yyy
Set the gateway information for an external print server.
yyy.yyy.yyy.yyy
Primary SMTP Gateway Specify SMTP server gateway and port information.
Secondary SMTP Gateway Port
5–30 Specify the amount of time in seconds before the server stops trying to send an e‑mail.
Reply Address Specify a reply address of up to 128 characters in the e-mail sent by the printer.

Understanding printer menus 142
Set the printer to use SSL for increased security when connecting to the SMTP server.
Specify the type of user authentication required for scan to e‑mail privileges.
No authentication required Login/Plain CRAM‑MD5 Digest‑MD5 NTLM Kerberos 5
Device‑Initiated E‑mail
Specify what credentials will be used when communicating to the SMTP server.
None Use Device SMTP Credentials
User‑Initiated E‑mail
None Use Device SMTP Credentials Use Session User ID and Password Use Session E‑mail address and Password Prompt user

Understanding printer menus 143
Limit the number and time frames of failed login attempts from the printer control panel before all users are locked out.
Login failures Failure time frame Lockout time Panel Login Timeout Remote Login Timeout
1–16 Limit the digit length of the PIN.
Limit the number of times an invalid PIN can be entered.
Limit the amount of time a confidential print job stays in the printer before it is deleted.
Off 1 hour 4 hours 24 hours 1 week

Understanding printer menus 144
Set a time limit on how long the printer stores print jobs.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs needing verification.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs for printing at a later time.
Off 1 hour 4 hours 24 hours 1 week
Disk Wiping erases only print job data on the printer hard disk that are not currently in use by the file system. All permanent data on the printer hard disk are preserved, such as downloaded fonts, macros, and held jobs.
Specify the mode for disk wiping.
Mark all disk space used by a previous print job. This method does not permit the file system to reuse this space until it has been cleared.
Single pass Multiple pass

Understanding printer menus 145
Export Log Let an authorized user export the security audit log.
Specify whether audit logs are deleted.
Specify how audit logs are configured.
Yes No Enable Remote Syslog
No Yes Remote Syslog Facility
0–23 Severity of events to log
Current Date and Time View the current date and time settings for the printer.
Manually Set Date and Time
Enter the date and time.
Select the time zone.
[list of time zones]
Set the printer to use the applicable daylight saving time (DST) start and end times associated with the printer Time Zone setting.
Enable Network Time Protocol, which synchronizes the clocks of devices on a network.

Understanding printer menus 146
Set the language of the text appearing on the printer display.
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portuguese Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese
Display the estimates of the supplies on the printer control panel, Embedded Web Server, menu settings, and device statistics reports.
Show estimates Do not show estimates
Minimize the use of energy, paper, or specialty media.
Off Energy Energy/Paper Paper

Understanding printer menus 147
Specify a custom beep when paper is loaded in the ADF.
Reduce the amount of noise produced by the printer.
Run the setup wizard.

Understanding printer menus 148
Specify a language and custom key information for the printer keyboard.
English Francais Francais Canadien Deutsch Italiano Espanol Greek Dansk Norsk Nederlands Svenska Suomi Portuguese Russian Polski Swiss German Swiss French Korean Magyar Turkce Cesky Simplified Chinese Traditional Chinese Japanese Custom Key [x]
Specify the default system of measurement for paper sizes.
U.S. Metric
Scan to PC Port Range
Specify a valid port range for printers behind a port blocking firewall. The valid ports are specified by two sets of numbers separated by a semicolon.

Understanding printer menus 149
Specify what is displayed on the upper left and right corners of the home screen.
Left side Right side Custom Text [x]
For the “Left side” and “Right side” menus, select from the following options:
None IP Address Hostname Contact Name Location Date/Time mDNS/DDNS Service Name Zero Configuration Name Cartridge Level Custom Text [x]
Customize the displayed information for the Black Toner, Cyan Toner, Magenta Toner, Yellow Toner, Fuser, and Transfer Module settings. Select from the following options:
Black Toner Cyan Toner Magenta Toner Yellow Toner Fuser Transfer Module
Do not display Display Message to display

Understanding printer menus 150
Specify the displayed information for Waste Toner Bottle, Paper Jam, Load Paper, and Service Errors settings.
Waste Toner Bottle Paper Jam Load Paper Service Errors
Select from the following options:
Yes No Message to display
Add or remove icons and buttons that appear on the home screen.
Change Language Copy Copy Shortcuts Fax Fax Shortcuts E‑mail E‑mail Shortcuts FTP FTP Shortcuts Search Held Jobs Held Jobs USB Drive Profiles and Solutions Bookmarks Jobs by user Forms and Favorites Basic Card Copy Scan to Network My Shortcuts Multi-Send
For each icon or button, select from the following options:
Display Do Not Display
Format the printer date.
MM‑DD‑YYYY DD‑MM‑YYYY YYYY‑MM‑DD

Understanding printer menus 151
Format the printer time.
12 hour A.M./P.M. 24 hour clock
20–100 Specify the brightness of the printer control panel screen.
Set copies from the scanner glass to only one page at a time.
Set the audio volume for the buttons.
Specify whether bookmarks are displayed from the Held Jobs area.
Specify whether image background removal is allowed in copy, fax, e‑mail, FTP, or scan‑to‑USB jobs.
Allow Custom Job Scans
Determine if Custom Job and Custom Job scanning settings appear for copy, scan, and fax jobs.
Specify how a scanned job should be reloaded if a paper jam occurs in the ADF.
Job level Page level
Web Page Refresh Rate
30–300 Specify the number of seconds between Embedded Web Server refreshes.

Understanding printer menus 152
Contact Name Specify a contact name for the printer.
Location Specify the location of the printer.
Set an alarm when the printer requires operator intervention. When activated, Alarm Control lets you set the number of times that the alarm sounds, while Cartridge Alarm lets you stop printing when a cartridge-low condition occurs.
Alarm Control Cartridge Alarm
For each alarm type, select from the following options:
Specify the number of minutes of inactivity before the printer enters a lower power state.
Set the amount of time in seconds the printer waits after a job is printed before it goes into a reduced power state.
Set the printer to operate at a low power state.
Disabled 1–3 hours 6 hours 1–3 days 1–2 weeks 1 month

Understanding printer menus 153
Set the printer to follow the setting of “Hibernate Timeout” even when an active Ethernet or fax connection exists.
Hibernate Timeout on Connection
Hibernate Do Not Hibernate
Set the amount of time in seconds the printer waits before returning the printer display to Ready state.
Set the printer to continue the specified job without returning to the home screen when the screen timeout timer expires.
Set the amount of time in seconds the printer waits to receive an end‑of‑job message before canceling the remainder of the print job.
Set the amount of time in seconds the printer waits for additional data before canceling a print job.

Understanding printer menus 154
Set the amount of time in seconds the printer waits for user intervention before it holds jobs that require unavailable resources and continues to print other jobs in the print queue.
Set the printer to restart when an error is encountered.
Reboot when idle Reboot always Reboot never
Determine the number of automatic reboots the printer can perform.
Let the printer automatically continue printing from certain offline situations when not resolved within the specified time period.
Specify whether the printer reprints jammed pages.
Print a page that may not have printed otherwise.

Understanding printer menus 155
Determine how the printer, while in idle state, reacts to a short press of the Sleep button.
Do Nothing Sleep Hibernate
Press and Hold Sleep Button
Determine how the printer, while in idle state, reacts to a long press of the Sleep button.
Do Nothing Sleep Hibernate
Restore printer settings to its factory defaults.
Do Not Restore Restore Now
Export the printer configuration package to a flash drive.
Specify the content of the original document.
Text Graphics Text/Photo Photo
Specify how the original document was produced.
Black/White Laser Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify whether copies are printed in color.

Understanding printer menus 156
Enable color in copies.
Specify whether an original document is two‑sided (duplex) or one‑sided, and then specify whether the copy should be two‑sided or one‑sided.
1 sided to 1 sided 1 sided to 2 sided 2 sided to 1 sided 2 sided to 2 sided
Allow copying of two or four sheets of a document on one page.
Off 2‑up Portrait 2‑up Landscape 4‑up Portrait 4‑up Landscape
Allow page borders in printed copies.
Keep the pages of a print job stacked in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)

Understanding printer menus 157
Specify the paper size of the original document.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in. ID Card
Specify the paper source for copy jobs.
Tray [x] Manual Feeder Multipurpose Feeder
Place a sheet of paper between transparencies.
Place a sheet of paper between pages, copies, or jobs.
Off Between Copies Between Jobs Between Pages
Specify the separator sheet source.
Tray [x] Multipurpose Feeder
1–9 Specify the level of darkness for the copy job.
1–999 Specify the number of copies for the copy job.

Understanding printer menus 158
Specify header and footer information and its location on the page.
Select from the following location options:
Off Date/Time Page number Custom text Print on
All pages First page only All but first page Custom text
Specify the overlay text printed on each page of the copy job.
Confidential Copy Draft Urgent Custom Off
Custom Overlay Specify the custom overlay text.
Allow interruption of a print job to copy a page or document.
Copy in a single copy job, a document that contains mixed paper sizes.
Allow Save as Shortcut
Save custom copy settings as shortcuts.
Adjust the amount of background visible on a copy.
‑4 to 4
Automatically center the content on the page.
Enable an equal balance of colors in the output.
Cyan - Red Magenta - Green Yellow - Blue

Understanding printer menus 159
Specify which color to drop during copies, and how much the dropout is increased or decreased.
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specify the contrast used for the copy job.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a copy.
‑4 to 4
Correct the slight skew in the scanned image.
Scan edge to edge
Allow edge-to-edge scanning of the original document.
1–5 Adjust the amount of sharpness of a copy.
Specify “warm” or “cool” outputs.
‑4 to 4
Create a sample copy of the original document.

Understanding printer menus 160
Analog Fax Setup mode sends the fax job through a telephone line.
Fax Name Specify the name of the fax in the printer.
Fax Number Specify the telephone number assigned to the fax.
Specify how the fax is identified.
Fax Name Fax Number
Set the printer to fax manually, which requires a line splitter and a telephone handset.
Define the allocation of non-volatile memory between sending and receiving fax jobs.
All receive Mostly receive Equal Mostly send All send
Specify whether the printer cancels fax jobs.
Specify the type of caller ID being used.
Specify the direction from where digits are masked in an outgoing fax number.
Off From left From right
0–58 Specify the number of digits to mask in an outgoing fax number.

Understanding printer menus 161
Configure the fax cover page.
Off by default On by default Never use Always use Include to Field
On Off Include from Field
On Off From Include Message Field
On Off Message Include Logo
On Off Include Footer [x]
On Off Footer [x]
Specify quality in dots per inch (dpi). A higher resolution gives better print quality, but increases the fax transmission time for outgoing faxes.
Standard Fine 200 dpi Super Fine 300 dpi

Understanding printer menus 162
Specify the paper size of the original document.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in.
Specify how text and graphics are oriented on a page.
Off Long edge Short edge
Specify the content of the original document.
Text Graphics Text/Photo Photo
Specify how the original document was produced.
Black/White Laser Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
1–9 Adjust the darkness of the output.
Dial Prefix Enter a dialing prefix, such as 99. A numeric entry field is provided.

Understanding printer menus 163
Establish a dialing prefix rule.
0–9 Specify the number of times the printer tries to send the fax to a specified number.
1–200 Specify the number of minutes between redials.
Enable or disable switchboard blind dialing without a dial tone.
Enable or disable Error Correction Mode for fax jobs.
Fax files that are scanned at the printer.
Allow the printer driver to send fax jobs.
Allow Save as Shortcut
Save fax numbers as shortcuts in the printer.
Specify the dialing sound, either as a tone or a pulse.
Specify the maximum speed in baud at which faxes are sent.
2400 4800 9600 14400 33600
Scan a document that contains mixed paper sizes into a single file.
Show a preview on the display for scan jobs.

Understanding printer menus 164
Adjust the amount of background visible on a scanned image.
‑4 to 4
Enable an equal balance of colors in the scanned image.
Cyan - Red Magenta - Green Yellow - Blue
Specify which color to drop, and how much the dropout is increased or decreased.
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specify the contrast in the scanned image.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible.
‑4 to 4
Correct the slight skew in the scanned image.
Scan edge to edge
Allow edge-to-edge scanning of the original document prior to faxing.
1–5 Adjust the sharpness of a fax.

Understanding printer menus 165
Specify “warm” or “cool” outputs.
‑4 to 4
Enable Color Fax Scans
Enable color faxing.
Off by default On by default Never use Always use
Auto Convert Color Faxes to Mono Faxes
Convert all outgoing faxes to black and white.
Allow the printer to receive fax jobs.
Remove fax jobs from the print queue when the job requires specific unavailable resources.
None Toner Toner and Supplies
1–25 Specify the number of rings before answering an incoming fax job.
Allow the printer to answer an incoming fax job.
0–9 Enter a code on the telephone number pad to begin receiving a fax.
Scale an incoming fax job so that it fits the size of the paper loaded in the designated fax source.

Understanding printer menus 166
Specify the paper source for printing incoming fax jobs.
Auto Tray [x] Manual Feeder Multipurpose Feeder
Enable two‑sided (duplex) printing for incoming fax jobs.
Enable the printer to include separator sheets for incoming fax jobs.
Off Before Job After Job
Specify where the printer picks the separator sheet.
Tray [x] Manual Feeder
Print the transmission information at the bottom of each page from a received fax.
Specify the maximum speed in baud at which faxes are received.
2400 4800 9600 14400 33600
Enable forwarding of received faxes to another recipient.
Print Print and Forward Forward
Specify the type of recipient to which faxes are forwarded.
Fax E‑mail FTP LDSS eSF
Forward to Shortcut Enter the shortcut number which matches the recipient type (Fax, E-mail, FTP, LDSS, or eSF).
Block No Name Fax
Enable blocking of incoming faxes sent from devices with no station ID or fax ID specified.
Banned Fax List Enable the list of blocked fax numbers stored in the printer.

Understanding printer menus 167
Enable fax holding all of the time or according to set schedule.
Off Always On Manual Scheduled Fax Holding Schedule
Enable Color Fax Receive
Enable the printer to receive fax in color.
Enable printing of a transmission log after each fax job.
Print log Do not print log Print only for error
Enable printing of a receive error log following a receive error.
Print Never Print on Error
Enable automatic printing of fax logs.
Specify the source of the paper used for printing logs.
Tray [x] Manual Feeder
Specify whether printed logs display the dialed number or the station name or fax name returned.
Remote Station Name Dialed Number
Enable access to the Fax Job log.
Enable access to the Fax Call log.

Understanding printer menus 168
Specify the mode of the speaker.
Always Off On until Connected Always On
Control the volume setting.
Control the fax speaker ringer volume.
All Rings Single Ring Only Double Ring Only Triple Ring Only Single or Double Rings Only Single or Triple Rings Only Double or Triple Rings Only
Specify ring patterns when the printer is answering calls.
Fax Mode sends the fax job to a fax server for transmission.
To Format Enter specific fax information using the virtual keyboard on the printer control panel.
SMTP Setup Specify SMTP setup information.
Primary SMTP Gateway Specify SMTP server port information.
Specify the image type for scanning to fax.
PDF (.pdf) XPS (.xps) TIFF (.tif)

Understanding printer menus 169
Specify the content of the original document.
Text Graphics Text/Photo Photo
Specify how the content was originally produced.
Black/White Laser Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify the resolution level for scanning to fax.
Standard Fine 200 dpi Super Fine 300 dpi
1–9 Adjust the darkness of the output.
Specify the orientation of the scanned image.
Specify the paper size of the document being scanned.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Custom Scan Size [x] Book Original Business Card 4 x 6 in. 3 x 5 in.

Understanding printer menus 170
Use Multi‑Page TIFF
Provide a choice between single‑page TIFF files and multiple‑page TIFF files. For a multiple-page scan‑to‑fax job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the scan job.
Enable receiving of analog faxes.
E‑mail Server Setup
Specify e‑mail server information.
Subject Message File Name
E‑mail Server Setup
Send a copy of the e-mail to the sender.
Send me a copy
Never appears On by default Off by default Always On
E‑mail Server Setup
Specify the maximum e-mail size in kilobytes (KB).
Max E‑mail size
E‑mail Server Setup
Send a message when an e-mail is greater than the configured size limit.
E‑mail Server Setup
Specify a domain name, such as a company domain name, and then limit e‑mail destinations only to that domain name.
E‑mail Server Setup
Define the e‑mail server path name, for example: /directory/path.
Server Login Password Path File Name Web Link

Understanding printer menus 171
Specify the format of the scanned file.
PDF (.pdf) Secure PDF TIFF (.tif) JPEG (.jpg) XPS (.xps)
Set the version of the PDF file to be scanned for e‑mailing.
1.2–1.6 A–1a
Specify the content of the original document.
Text Graphics Text/Photo Photo
Specify how the original document was produced.
Black/White Laser Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify whether to print copies in color.
Specify the resolution of the scan in dots per inch.
75 dpi 150 dpi 200 dpi 300 dpi 400 dpi 600 dpi
1–9 Adjust the darkness of the output.
Specify the orientation of the scanned image.

Understanding printer menus 172
Specify the paper size of the document being scanned.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in.
Specify how the text and graphics are oriented on the page.
Off Long edge Short edge
Set the quality of a JPEG photo image in relation to file size and quality of the image.
Best for content 5–90
5–90 Set the quality of a text image in relation to file size and quality of the image.
5–90 Set the quality of a text or photo image in relation to file size and the quality of the image.
5–90 Set the quality of a photo image in relation to file size and the quality of the image.

Understanding printer menus 173
E‑mail images sent as
Specify how images are sent.
Use Multi‑Page TIFF
Provide a choice between single-page TIFF files and multiple‑page TIFF files. For a multiple-page scan‑to‑e-mail job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the job.
Specify whether or not the transmission log prints.
Print log Do not print log Print only for error
Specify the paper source for printing e-mail logs.
Tray [x] Manual Feeder
E‑mail Bit Depth
Enable the Text/Photo mode to produce smaller file sizes by using 1‑bit images.
1 bit 8 bit
Copy a document that contains mixed paper sizes.
Specify whether or not a preview will appear on the display for scan jobs.
Allow Save as Shortcut
Save e-mail addresses as shortcuts.
Adjust the amount of background visible on a scanned image.
‑4 to 4
Enable an equal balance of colors in the output.
Cyan - Red Magenta - Green Yellow - Blue

Understanding printer menus 174
Specify which color to drop during scanning, and how much to increase or decrease the dropout.
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specify the contrast of the output.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4
Scan edge to edge
Allow edge-to-edge scanning of the original document.
1–5 Adjust the amount of sharpness on a scanned image.
Enable the user to specify “warm” or “cool” outputs.
‑4 to 4
Use cc:/bcc:
Enable the use of the “cc” and “bcc” fields.

Understanding printer menus 175
Specify the format of the file for FTP sending.
PDF (.pdf) Secure PDF (.pdf) TIFF (.tif) JPEG (.jpg) XPS (.xps)
Set the version level of the PDF file for FTP sending.
1.2–1.6 A–1a
Specify the content of the original document.
Text Graphics Text/Photo Photo
Specify how the original document was produced.
Black/White Laser Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify whether to print copies in color.
Specify the quality of the scan in dots per inch (dpi).
75 dpi 150 dpi 200 dpi 300 dpi 400 dpi 600 dpi
1–9 Adjust the darkness of the output.
Specify the orientation of the scanned image.

Understanding printer menus 176
Specify the paper size of the original document.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in.
Specify how the text and graphics are oriented on the page.
Off Long edge Short edge
Set the quality of a JPEG photo image in relation to file size and the quality of the image.
Best for content 5–90
5–90 Set the quality of the text in relation to file size and the quality of the image.
5–90 Set the quality of a text/photo image in relation to file size and the quality of the image.
5–90 Set the quality of a photo image in relation to file size and the quality of the image.

Understanding printer menus 177
Use Multi‑Page TIFF
Provide a choice between single-page TIFF files and multiple‑page TIFF files. For a multiple-page scan‑to‑FTP job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the job.
Specify whether the transmission log prints.
Print log Do not print log Print only for error
Specify a paper source when printing FTP logs.
Tray [x] Manual Feeder
Enable the Text/Photo mode to have smaller file sizes by using 1‑bit images.
1 bit 8 bit
File Name Type a base file name.
Copy a document that contains mixed paper sizes into a single scan job.
Specify whether a preview will appear on the display for scan jobs.
Allow Save as Shortcut
Enable shortcut creation for FTP addresses.
Adjust the amount of background visible on a copy.
‑4 to 4
Enable an equal balance of colors in the output.
Cyan - Red Magenta - Green Yellow - Blue

Understanding printer menus 178
Specify which color to drop during scanning, and how much to increase or decrease the dropout.
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specify the contrast of the output.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4
Scan edge to edge
Allow edge-to-edge scanning of the original document.
1–5 Adjust the amount of sharpness of a scanned image
Enable the user to specify “warm” or “cool” outputs.
‑4 to 4

Understanding printer menus 179
Specify the format of the file to be sent through FTP.
PDF (.pdf) Secure PDF TIFF (.tif) JPEG (.jpg) XPS (.xps)
Set the version of the PDF file to be sent through FTP.
1.2–1.6 A1‑a
Specify the content of the original document.
Text Graphics Text/Photo Photo
Specify how the original document was produced.
Black/White Laser Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify whether the device captures and transmits content in color or in black and white.
Specify the resolution of the scan in dots per inch (dpi).
75 dpi 150 dpi 200 dpi 300 dpi 400 dpi 600 dpi
1–9 Adjust the darkness of the output.
Specify the orientation of the scanned image.

Understanding printer menus 180
Specify the paper size of the original document.
Letter Legal Executive Folio Statement Oficio (Mexico) Universal Auto Size Sense Mixed Sizes A4 A5 A6 JIS B5 Custom Scan Size [x] Book Original Business Card 3 x 5 in. 4 x 6 in.
Specify how the text and graphics are oriented on a page.
Off Long edge Short edge
Set the quality of a JPEG photo image in relation to file size and quality.
Best for content 5–90
5–90 Set the quality of the text in relation to file size and quality of the image.
5–90 Set the quality of a text/photo image in relation to file size and quality.
5–90 Set the quality of a photo image in relation to file size and quality.

Understanding printer menus 181
Use Multi‑Page TIFF
Provide a choice between single-page TIFF files and multiple‑page TIFF files. For a multiple-page scan‑to‑FTP job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page.
Enable the Text/Photo mode to have smaller file sizes by using 1‑bit images when Color is set to Off.
1 bit 8 bit
File Name Type a base file name.
Copy a document containing mixed paper sizes in a single copy job.
Show a preview on the display for scan jobs.
Adjust the amount of background visible in a scanned image.
‑4 to 4
Enable an equal balance of colors in the output.
Cyan - Red Magenta - Green Yellow - Blue
Specify which color to drop during scanning, and how much the dropout is increased or decreased.
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold

Understanding printer menus 182
Specify the contrast of the output.
0–5 Best for content
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4
Correct the slight skew in the scanned image.
Scan edge to edge
Allow edge-to-edge scanning of the original document.
1–5 Adjust the amount of sharpness on a scanned image.
Specify “warm” or “cool” outputs.
‑4 to 4
1–999 Specify a default number of copies for each print job.
Set a default paper source for all print jobs.
Tray [x] MP Feeder Manual Paper Manual Envelope
Specify whether the device captures and transmits content in color or in black and white.

Understanding printer menus 183
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)
Specify whether prints are on one side or on both sides of the page.
1 sided 2 sided
Define binding for duplexed pages in relation to page orientation.
Long Edge Short Edge
Specify the orientation of a multiple‑page document.
Print multiple pages on one sheet of paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Print a border on each page.
Specify the order in which pages are printed on a single sheet when using Paper Saver.
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify whether blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages

Understanding printer menus 184
Specify the paper source for separator sheets.
Tray [x] Manual Feeder
Specify whether blank pages are inserted in a print job.
Do Not Print Print
Set the default printer language.
PCL Emulation PS Emulation
Specify that print jobs be removed from the print queue if they require unavailable printer options or custom settings. They are stored in a separate print queue, so other jobs print normally. When the missing information or options are obtained, the stored jobs print.
Set the logical and physical printable area.
Normal Fit to Page Whole Page
Set the printer for a faster print speed or for a higher toner yield.
Max Yield Max Speed
Set the printer to print text and graphics using only the black toner cartridge.

Understanding printer menus 185
Set the storage location for downloads.
Specify how the printer handles temporary downloads, such as fonts and macros stored in the RAM, when the printer receives a job that requires more memory than is available.
Specify the order in which held and confidential jobs are printed when Print All is selected.
Alphabetical Oldest First Newest First
Specify whether two‑sided (duplex) printing is set as the default for all print jobs.
1 sided 2 sided
Click File > Print, and then click Properties, Preferences, Options, or Setup. For Macintosh users:
Choose File > Print, and then adjust the settings from the Print dialog and pop‑up menus.
Define binding for duplexed pages in relation to page orientation.
Long Edge Short Edge

Understanding printer menus 186
1–999 Specify the default number of copies for each print job.
Specify whether blank pages are inserted in a print job.
Do Not Print Print
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)
Specify whether blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages
Specify the paper source for separator sheets.
Tray [x] Manual Feeder
Print multiple pages on a single sheet of paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Specify the order in which pages are printed on a single sheet when using Paper Saver.
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify the orientation in which pages are printed on a single sheet.

Understanding printer menus 187
Print a border when using Paper Saver.
Specify whether images are printed in black and white or in color.
Adjust the color output on the printed page.
Specify the printed output resolution in dots per inch or in color quality (CQ).
1200 dpi 4800 CQ
1–5 Lighten or darken the printed output.
Enable a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts.
Click File > Print, and then click Properties, Preferences, Options, or Setup. For Macintosh users:
Choose File > Print, and then adjust the settings from the Print dialog and pop‑up menus.

Understanding printer menus 188
Reduce the amount of toner used for graphics and images. The amount of toner used for text is not reduced.
Adjust the printed output either by lightening or darkening it. You can conserve toner by lightening the output.
‑6 to 6
0–5 Adjust the contrast of printed objects.
0–5 Adjust saturation in color outputs.
Adjust color in printed output by increasing or decreasing the amount of toner being used for each color.
‑5 to 5 Magenta
‑5 to 5 Yellow
‑5 to 5 Black
‑5 to 5 Reset Defaults
Print sample pages for each of the RGB and CMYK color conversion tables used in the printer.
sRGB Display sRGB Vivid Display—True Black Vivid Off—RGB US CMYK Euro CMYK Vivid CMYK Off—CMYK

Understanding printer menus 189
Customize the RGB color conversions.
RGB Image RGB Text RGB Graphics
Select from the following options:
Vivid sRGB Display Display—True Black sRGB Vivid Off
Customize the CMYK color conversions. Select from the following options:
CMYK Image CMYK Text CMYK Graphics
US CMYK Euro CMYK Vivid CMYK Off
Spot Color Replacement Assign specific CMYK values to named spot colors.
Color Adjust Initiate a recalibration of color conversion tables and allow the printer to make adjustments for color variations in output.
Use To · Manual Color · Manual Color (continued)

Understanding printer menus 190
Determine and set if the printer creates a log of the print jobs it receives.
Job Accounting Utilities Print and delete log files or export them to a flash drive.
Determine and set how often a log file is created.
Log Action at End of Frequency
Determine and set how the printer responds when the frequency threshold expires.
None E‑mail Current Log E‑mail & Delete Current Log Post Current Log Post & Delete Current Log
Disk Near Full Level
Specify the maximum size of the log file.
Disk Near Full Action
Determine and set how the printer responds when the printer hard disk is nearly full.
None E‑mail Current Log E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post Current Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
Determine and set how the printer responds when disk usage reaches the maximum limit (100MB).
None E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
URL to Post Logs Determine and set where the printer posts job accounting logs.

Understanding printer menus 191
E‑mail to Send Logs Specify the e‑mail address to which the device sends job accounting logs.
Log File Prefix Specify the prefix you want for the log file name.
Delete confidential and held jobs from the printer hard disk.
Confidential Held Not Restored All
Format the flash memory.
Delete Downloads on Disk
Delete downloads from the printer hard disk, including all held jobs, buffered jobs, and parked jobs.
Delete Now Do Not Delete
Activate Hex Trace Assist in isolating the source of a print job problem.

Understanding printer menus 192
Provide an estimate of the percentage coverage of toner on a page. The estimate is printed on a separate page at the end of each print job.
Print a page containing information on errors, including XML markup errors.
Scale page content to fit the selected paper size.
Print annotations in a PDF.
Do Not Print Print
Print a page containing the PostScript error.
Lock PS Startup Mode
Enable users to disable the SysStart file.
Establish the font search order.

Understanding printer menus 193
Enhance the contrast and sharpness of low‑resolution images and smoothen their color transitions.
Specify the set of fonts used by the Font Name menu.
Resident Disk Download Flash All
Identify a specific font and the option where it is stored.
Specify the symbol set for each font name.
Change the point size for scalable typographic fonts.
1.00–1008.00

Understanding printer menus 194
Specify the font pitch for scalable monospaced fonts.
0.08–100
Specify the orientation of text and graphics on the page.
Specify the number of lines that print on each page.
Set the printer to print on A4‑size paper.
198 mm 203 mm
Specify whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command.
Auto CR after LF
Specify whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command.
Auto LF after CR

Understanding printer menus 195
Configure the printer to work with printer software or programs that use different source assignments for trays and feeders.
Off None 0–199 Assign Tray [x]
Off None 0–199 Assign Manual Paper
Off None 0–199 Assign Manual Env
Display the factory default setting assigned to each tray or feeder.
MPF Default = 8 T1 Default = 1 T1 Default = 4 T1 Default = 5 T1 Default = 20 T1 Default = 21 Env Default = 6 MPaper Default = 2 MEnv Default = 3
Restore all tray and feeder assignments to the factory default settings.

Understanding printer menus 196
Joanna MT Letter Gothic Lubalin Graph Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino StempelGaramond Taffy Times TimesNewRoman Univers Zapf Chancery NewSansMTCS NewSansMTCT New SansMTJA NewSansMTKO
Set the default font for HTML documents.
Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text Intl CG Times Intl Courier Intl Univers
1–255 pt Set the default font size for HTML documents.
1–400% Scale the default font for HTML documents.
Set the page orientation for HTML documents.

Understanding printer menus 197
8–255 mm Set the page margin for HTML documents.
Specify whether to print backgrounds on HTML documents.
Do Not Print Print
Select the optimal paper size, scaling, and orientation.
Invert bitonal monochrome images.
Scale the image to fit the selected paper size.
Anchor Top Left Best Fit Anchor Center Fit Height/Width Fit Height Fit Width
Set the image orientation.
Portrait Landscape Reverse Portrait Reverse Landscape
The Help menu consists of a series of Help pages that are stored in the multifunction printer (MFP) as PDF files. They contain information about using the printer and performing various tasks, including copying, scanning, e‑mailing, and faxing.
English, French, German, and Spanish translations are stored in the printer. Other translations are available at http://support.lexmark.com.

Understanding printer menus 198
Print All Guides Prints all the guides
Copy Guide Provides information about making copies and changing settings
E‑mail Guide Provides information about sending e‑mails using addresses, shortcut numbers, or the address book, and about changing settings
Fax Guide Provides information about sending faxes using fax numbers, shortcut numbers, or the address book, and about changing settings
FTP Guide Provides information about scanning documents directly to an FTP server using an FTP address, shortcut numbers, or the address book, and about changing settings
Color Quality Provides information about solving color quality issues
Print Defects Guide Provides help in resolving repeating defects in copies or prints
Information Guide Provides help in locating additional information
Supplies Guide Provides part numbers for ordering supplies
Menu item Description

Saving money and the environment 199
Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impact on the environment. We design with the environment in mind, engineer our packaging to reduce materials, and provide collection and recycling programs. For more information, see:
By selecting certain printer settings or tasks, you may be able to reduce your printer's impact even further. This chapter outlines the settings and tasks that may yield a greater environmental benefit.
Studies show that as much as 80% of the carbon footprint of a printer is related to paper usage. You can significantly reduce your carbon footprint by using recycled paper and the following printing suggestions, such as printing on both sides of the paper and printing multiple pages on one side of a single sheet of paper.
For information on how you can quickly save paper and energy using one printer setting, see “Using Eco‑Mode” on page 200.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser printers. For more information on recycled papers that work well with your printer, see “Using recycled paper and other office papers” on page 60.
There are a number of ways you can reduce the amount of paper and toner you use when printing. You can:
If your printer model supports duplex printing, then you can control whether print appears on one or two sides of the paper by selecting 2‑sided printing from the Print dialog or the Lexmark Toolbar.
You can print up to 16 consecutive pages of a multiple‑page document onto one side of a single sheet of paper by selecting a setting from the Multipage printing (N‑Up) section of the Print dialog screen.
Before printing or making multiple copies of a document:

Saving money and the environment 200
Carefully select and load paper to avoid paper jams. For more information, see “Avoiding jams” on page 240.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Eco‑Mode > select a setting
Off Use the factory default settings for all settings associated with Eco‑Mode. Off supports the performance specifications of the printer.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy and Paper modes.
3 Click Submit.
Enable Quiet Mode to reduce printer noise.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Quiet Mode > select a setting
Use To

Saving money and the environment 201
On Reduce printer noise.
Off Use factory default settings.
3 Click Submit.
To save energy, decrease the number of minutes the printer waits before it enters Sleep mode. Select from 1 to 120. The factory default setting is 30 minutes.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Timeouts.
3 In the Sleep Mode field, enter the number of minutes you want for the printer to wait before it enters Sleep mode.
4 Click Submit.
1 From the home screen, navigate to:
> Settings > General Settings > Timeouts > Sleep Mode
2 In the Sleep Mode field, select the number of minutes you want for the printer to wait before it enters Sleep mode.
Use To · 3 Touch

Saving money and the environment 202
Hibernate is an ultra‑low power operating mode. When operating in Hibernate mode, the printer is essentially off, and all other systems and devices are powered down safely.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Sleep Button Settings.
3 From the Press Sleep Button or Press and Hold Sleep Button drop‑down menu, select Hibernate.
4 Click Submit.
1 From the home screen, navigate to:
> Settings > General Settings
2 Touch Press Sleep Button or Press and Hold Sleep Button.
3 Touch Hibernate >
Hibernate Timeout lets you set the amount of time the printer waits after a print job is processed before it goes into a reduced power state.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Timeouts.
3 From the Hibernate Timeout menu, select the number of hours, days, weeks, or months you want for the printer to wait before it goes into a reduced power state.
4 Click Submit.

Saving money and the environment 203
1 From the printer control panel, navigate to:
> Settings > General Settings > Timeouts > Hibernate Timeout
2 Select the amount of time the printer waits after a print job is processed before it enters Hibernate mode.
Schedule Power Modes lets you schedule when the printer goes into a reduced power state or into Ready state.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Schedule Power Modes.
3 From the Action menu, select the power mode.
4 From the Time menu, select the time.
5 From the Day(s) menu, select the day or days.
6 Click Add.
To save energy, or if you are have trouble reading your display, adjust the brightness of the display.
Available settings range from 20–100. The factory default setting is 100.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings.
3 In the Screen Brightness field, enter the brightness percentage you want for the display.
4 Click Submit.
3 Touch

Saving money and the environment 204
1 From the home screen, navigate to:
> Settings > General Settings > Screen Brightness
2 In the Screen Brightness field, enter the brightness percentage you want for the display.
Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information, see:
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country or region from the list.
3 Follow the instructions on the computer screen.
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark will recycle the box.
Lexmark Cartridge Collection Program diverts millions of Lexmark cartridges from landfills annually by making it both easy and free for Lexmark customers to return used cartridges to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. Boxes used to return the cartridges are also recycled.
3 Touch

Saving money and the environment 205
To return Lexmark cartridges for reuse or recycling, follow the instructions that came with your printer or cartridge and use the prepaid shipping label. You can also do the following:
1 Go to www.lexmark.com/recycle.
2 From the Toner Cartridges section, select your country or region.
3 Follow the instructions on the computer screen.

Securing the printer 206
Using the security lock feature
The printer is equipped with a security lock feature. Attach a security lock compatible with most laptop computers in the location shown to secure the printer in place.


Your printer contains various types of memory that can store device and network settings, and user data.
Type of memory Description
Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print jobs.
Non-volatile memory Your printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store the operating system, device settings, network information and bookmark settings, and embedded solutions.
Hard disk memory Some printers have a hard disk drive installed. The printer hard disk is designed for printer-specific functionality. This lets the printer retain buffered user data from complex print jobs, as well as form data, and font data.
Erase the content of any installed printer memory in the following circumstances:

Securing the printer 207
In high‑security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer hard disk cannot be accessed when the printer—or its hard disk—is removed from your premises.
The volatile memory (RAM) installed in your printer requires a power source to retain information. To erase the buffered data, simply turn off the printer.
Erase individual settings, device and network settings, security settings, and embedded solutions by following these steps:
1 Turn off the printer.
2 Hold down 2 and 6 on the keypad while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display instead of the standard home screen icons.
3 Touch Wipe All Settings.
The printer will restart several times during this process.
4 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.

Securing the printer 208
Configuring Disk Wiping in the printer menus lets you remove residual confidential material left by print jobs by securely overwriting files that have been marked for deletion.
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, the touch screen displays a list of functions.
4 Touch Yes to proceed with disk wiping.
5 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.
Enable hard disk encryption to prevent loss of sensitive data in the event the printer or its hard disk is stolen.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Security > Disk Encryption.
3 From the Disk encryption menu, select Enable.

Securing the printer 209
4 Click Submit.
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
3 Touch Disk Encryption > Enable.
4 Touch Yes to proceed with disk wiping.
5 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.
In high-security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer cannot be accessed by unauthorized persons. For more information, visit the Lexmark security Web page.
You can also see the Embedded Web Server Administrator’s Guide for additional information:
1 Go to http://support.lexmark.com.
2 In the Search field, type the model name of your printer, and then click Go.
3 Click the Manuals tab, and then select the Embedded Web Server Administrator’s Guide.

Maintaining the printer 210
Periodically, certain tasks are required to maintain optimum print quality.
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:
1 Make sure that the printer is turned off and unplugged from the electrical outlet.
2 Remove paper from the standard bin, multipurpose feeder, and manual feeder.
3 Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.
4 Dampen a clean, lint-free cloth with water, and use it to wipe the outside of the printer.
5 Make sure all areas of the printer are dry before sending a new print job.

Maintaining the printer 211
Clean the scanner glass if you encounter print quality problems, such as streaks on copied or scanned images.
1 Slightly dampen a soft, lint-free cloth or paper towel with water.
2 Open the scanner cover.
3 Clean all the areas shown, and then let them dry.

1 White underside of the ADF cover
2 White underside of the scanner cover
4 Close the scanner cover.
3 Scanner glass · 4 ADF glass

Maintaining the printer 212
From the home screen, navigate to:
Status/Supplies > View Supplies
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Device Status > More Details.
The estimated number of remaining pages is based on the recent printing history of the printer. Its accuracy may vary significantly and is dependent on many factors, such as actual document content, print quality settings, and other printer settings.
The accuracy of the estimated number of remaining pages may decrease when the actual printing consumption is different from the historical printing consumption. Consider the variable level of accuracy before purchasing or replacing supplies based on the estimate. Until an adequate print history is obtained on the printer, initial estimates assume future supplies consumption based on the International Organization for Standardization* test methods and page content.
* Average continuous black or composite CMY declared cartridge yield in accordance with ISO/IEC 19798.

Maintaining the printer 213
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, visit the Lexmark Web site at www.lexmark.com or contact the place where you purchased the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. Use of third-party supplies or parts can affect warranty coverage. Damage caused by the use of third-party supplies or parts is not covered by the warranty. All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.

Item United States and Canada European Union (EU), European Economic Area
For more information on countries located in each region, visit www.lexmark.com/regions.

Maintaining the printer 214

Item United States and Canada European Union (EU), European Economic Area
For more information on countries located in each region, visit www.lexmark.com/regions.

For more information on countries located in each region, visit www.lexmark.com/regions.



Maintaining the printer 215
Item All countries and regions
Waste toner bottle C540X75G

2 Waste toner bottle
3 Right side cover
1 Unpack the replacement waste toner bottle.
2 Open the front door.
1 Top door · 4 Front door

Maintaining the printer 216

3 Open the top door.


4 Remove the right side cover.


Maintaining the printer 217
5 Press the green levers on each side of the waste toner bottle, and then remove the waste toner bottle.


6 Seal the used waste toner bottle in the enclosed packaging.
For more information, see “Recycling Lexmark products” on page 204.
7 Insert the replacement waste toner bottle.

Maintaining the printer 218
8 Insert the right side cover.


9 Slide and hold the release latch on the right side of the printer, and then slowly close the top door.
10 Close the front door.

Maintaining the printer 219
1 Open the front door.
2 Open the top door.

Maintaining the printer 220
3 Remove the toner cartridges by lifting the handles, and then gently pulling them away from the imaging kit.


4 Remove the right side cover.

5 Press the green levers on each side of the waste toner bottle, and then remove the waste toner bottle.


Maintaining the printer 221
6 Lift the blue levers on the imaging kit, and then pull the imaging kit until it stops.

7 Press down the blue lever, and then grasp the green handles on the sides to pull out the imaging kit.

8 Unpack the replacement black and color imaging kit.


9 Seal the used imaging kit in the bag that the replacement imaging kit came in.

Maintaining the printer 222
For more information, see “Recycling Lexmark products” on page 204.

10 Gently shake the yellow, cyan, magenta, and black developer units side‑to‑side.

11 Remove the red packing strip and the attached fabric from the developer units.


Maintaining the printer 223
12 Gently insert the yellow, cyan, magenta, and black developer units.

13 Remove the red packing strip from the imaging kit.



Maintaining the printer 224
14 Align and then insert the imaging kit.


15 Gently but firmly push the blue levers down until the imaging kit fits into place.

16 Insert the waste toner bottle.

Maintaining the printer 225
17 Insert the right side cover.

18 Insert the toner cartridges.
19 Slide and hold the release latch on the right side of the printer, and then slowly close the top door.

Maintaining the printer 226
20 Close the front door.
1 Open the top door.



Maintaining the printer 227
2 Remove the toner cartridge by lifting the handle, and then gently pulling it away from the imaging kit.

3 Unpack the new toner cartridge, and then remove its packaging.
4 Align the new toner cartridge, and then press the cartridge down until it fits into place.

Maintaining the printer 228
5 Slide and hold the release latch on the right side of the printer, and then slowly close the top door.

6 Seal the used toner cartridge in the bag that the replacement toner cartridge came in.
For more information, see “Recycling Lexmark products” on page 204.
Replace the developer unit when a print quality defect occurs or when damage occurs to the printer.
1 Open the front door.

Maintaining the printer 229
2 Open the top door.
3 Lift the toner cartridge handle, and then gently pull it from the imaging kit.

Maintaining the printer 230
4 Remove the right side cover.
5 Press the green levers on each side of the waste toner bottle, and then remove the waste toner bottle.
6 Lift the blue levers on the imaging kit, and then pull the imaging kit until it stops.

Maintaining the printer 231
7 Press down the blue lever, and then grasp the green handles on the sides to pull out the imaging kit.
8 Remove the used developer unit.

9 Gently shake the replacement developer unit side‑to‑side before removing it from its packaging.

Maintaining the printer 232
10 Remove the red shipping cover from the developer unit.
11 Insert the developer unit.
12 Align and then insert the imaging kit.

Maintaining the printer 233
13 Gently but firmly push the blue levers down until the imaging kit fits into place.
14 Replace the waste toner bottle.
15 Insert the right side cover.

Maintaining the printer 234
16 Insert the toner cartridges.
17 Slide and hold the release latch on the right side of the printer, and then slowly close the top door.
18 Close the front door.
19 Seal the used developer unit in the bag that the replacement developer unit came in.
For more information, see “Recycling Lexmark products” on page 204.

Maintaining the printer 235
The printer and its hardware options can be safely moved to another location by following these precautions:
When shipping the printer, use the original packaging.

Managing the printer 236
Finding advanced networking and administrator information
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server Administrator's Guide on the Lexmark Web site at http://support.lexmark.com.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Check the virtual display that appears at the top left corner of the screen.
The virtual display works as an actual display would work on a printer control panel.
Configure the printer to send you e‑mail alerts when the supplies are getting low or when the paper needs to be changed or added, or when there is a paper jam.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings.
3 From the Other Settings menu, click E‑mail Alert Setup.
4 Select the items you want to be notified on, and then type the e‑mail addresses.
5 Click Submit.
You can view some reports from the Embedded Web Server. These reports are useful for assessing the status of the printer, network, and supplies.
1 Open a Web browser, and then type the printer IP address in the address field.

Managing the printer 237
2 Click Reports, and then click the type of report you want to view.
You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Supply Notifications.
3 From the drop‑down menu for each supply, select one of the following notification options:
Off The normal printer behavior for all supplies occurs.
E‑mail Only The printer generates an e-mail when the supply condition is reached. The status of the supply appears on the menus page and status page.
Continuable Stop1 The printer stops processing jobs when the supply condition is reached. The user needs to press a button to continue printing.
Non Continuable Stop1,2 The printer stops when the supply condition is reached. The supply must be replaced to continue printing.
1 The printer generates an e-mail about the status of the supply when supply notification is enabled.
2 The printer stops when some supplies become empty to prevent damage.
4 Click Submit.
Notification Description

Managing the printer 238
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Configuration > Other Settings tab > Security > Confidential Print Setup.
4 Save the modified settings.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click the Copy Printer Settings.
3 To change the language, select a language from the drop-down menu, and then click Click here to submit language.
4 Click Printer Settings.
5 Type the IP addresses of the source and target printers in their appropriate fields.
6 Click Copy Printer Settings.
If you want to keep a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings. For more information, see “Printing a menu settings page” on page 43.

Managing the printer 239
If you want a more comprehensive method of restoring the printer factory default settings, then perform the Wipe All Settings option. For more information, see “Erasing non‑volatile memory” on page 207.
From the home screen, navigate to:
> Settings > General Settings > Factory Defaults > Restore Now >

Avoiding jams
Correct loading of paper Incorrect loading of paper


Clearing jams 240


When a jam occurs, a message indicating the jam location and information to clear the jam appears on the printer display. Open the doors, covers, and trays indicated on the display to remove the jam.


Jam location Message on the display What to do
[x]‑page jam, open automatic feeder top cover [28y.xx]
Remove all paper from the ADF tray, and then remove the jammed paper.
2 Standard bin [x]‑page jam, clear standard bin [203.xx]
Clearing jams 241
![Page 242 of the Lexmark 415 user manual — [x] ‑ page jam, clear standard bin [203.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-242.webp?w=400)
Jam location Message on the display What to do
3 Fuser [x]‑page jam, open front door to clear fuser [202.xx]
Open the front door, then pull the tab and hold the fuser cover down, and then remove the jammed paper.
4 Front door [x]‑page jam, open front door [20y.xx] Open the front door, and then remove the jammed
paper.
5 Duplex area [x]‑page jam, open front door to clear duplex [23y.xx]
Open the front door, and then remove the jammed paper.
6 Tray [x] [x]‑page jam, open tray [x] [24y.xx] Pull out the indicated tray, and then remove the jammed paper.
7 Multipurpose feeder [x]‑page jam, clear multipurpose feeder [250.xx]
Push the paper release lever to lift the paper rollers, and then remove the jammed paper.
8 Manual feeder [x]‑page jam, clear manual feeder [251.xx]
Remove the jammed paper.
1 Open the top door.
![Lexmark 415 — [x] ‑ page jam, clear standard bin [203.xx] diagram (page 242)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-90.webp)
![Lexmark 415 — [x] ‑ page jam, clear standard bin [203.xx] diagram (page 242)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-91.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 242
![Page 243 of the Lexmark 415 user manual — [x]-page jam, clear standard bin [203.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-243.webp?w=400)
![Lexmark 415 — [x]-page jam, clear standard bin [203.xx] diagram (page 243)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-92.webp)
3 Open the front door.
![Lexmark 415 — [x]-page jam, clear standard bin [203.xx] diagram (page 243)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-93.webp)
a If there is a jammed paper under the fuser, then firmly grasp the paper on each side, and then gently pull it out.
Clearing jams 243
![Page 244 of the Lexmark 415 user manual — [x]-page jam, clear standard bin [203.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-244.webp?w=400)
b Pull the green lever to open the fuser cover.
![Lexmark 415 — [x]-page jam, clear standard bin [203.xx] diagram (page 244)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-94.webp)
![Lexmark 415 — [x]-page jam, clear standard bin [203.xx] diagram (page 244)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-95.webp)
c If there is a jammed paper in the fuser, then hold down the fuser cover, and then remove the paper.
![Lexmark 415 — [x]-page jam, clear standard bin [203.xx] diagram (page 244)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-96.webp)
Clearing jams 244
![Page 245 of the Lexmark 415 user manual — [x]-page jam, open front door to clear fuser [202.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-245.webp?w=400)
4 Slide and hold the release latch on the right side of the printer, and then slowly close the top door.
5 Close the front door.
to clear the message and continue printing. For non‑touch‑screen printer
6 From the printer control panel, touch
models, select Next > Clear the jam, press OK, and then press to confirm.
1 Open the front door.
Clearing jams 245
![Page 246 of the Lexmark 415 user manual — [x]-page jam, open front door to clear fuser [202.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-246.webp?w=400)
2 Open the top door.
Clearing jams 246
![Page 247 of the Lexmark 415 user manual — [x]-page jam, open front door to clear fuser [202.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-247.webp?w=400)
3 Pull the green lever to open the fuser cover.
4 Hold down the fuser cover, and then remove the jammed paper.
Clearing jams 247
![Page 248 of the Lexmark 415 user manual — [x]-page jam, open front door [20y.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-248.webp?w=400)
5 Slide and hold the release latch on the right side of the printer, and then slowly close the top door.
6 Close the front door.
to clear the message and continue printing. For non‑touch‑screen printer
7 From the printer control panel, touch
models, select Next > Clear the jam, press OK, and then press to confirm.
1 Open the front door.
Clearing jams 248
![Page 249 of the Lexmark 415 user manual — [x] ‑ page jam, open front door to clear duplex [23y.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-249.webp?w=400)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
3 Close the front door.
to clear the message and continue printing. For non‑touch‑screen printer
4 From the printer control panel, touch
models, select Next > Clear the jam, press OK, and then press to confirm.
1 Open the front door.
Clearing jams 249
![Page 250 of the Lexmark 415 user manual — [x] ‑ page jam, open tray [x] [24y.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-250.webp?w=400)
![Lexmark 415 — [x]-page jam, open tray [x] [24y.xx] diagram (page 250)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-97.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
3 Close the front door.
4 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > Clear the jam, press OK, and then press to confirm.
1 Pull out the tray completely.
Clearing jams 250
![Page 251 of the Lexmark 415 user manual — [x]-page jam, open tray [x] [24y.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-251.webp?w=400)
![Lexmark 415 — [x]-page jam, open tray [x] [24y.xx] diagram (page 251)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-98.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark 415 — [x]-page jam, open tray [x] [24y.xx] diagram (page 251)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-99.webp)
3 Insert the tray.
4 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > Clear the jam, press OK, and then press to confirm.
Clearing jams 251
![Page 252 of the Lexmark 415 user manual — [x] ‑ page jam, clear multipurpose feeder [250.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-252.webp?w=400)
1 Pull out the standard 250-sheet tray (Tray 1) and manual feeder.
![Lexmark 415 — [x] ‑ page jam, clear manual feeder [251.xx] diagram (page 252)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-100.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark 415 — [x] ‑ page jam, clear manual feeder [251.xx] diagram (page 252)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-101.webp)
3 Insert the tray.
4 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > Clear the jam, press OK, and then press to confirm.
1 Push the paper release lever in the multipurpose feeder to access the jammed paper, and then gently pull out the paper.
Clearing jams 252
![Page 253 of the Lexmark 415 user manual — [x]-page jam, clear manual feeder [251.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-253.webp?w=400)
![Lexmark 415 — [x]-page jam, clear manual feeder [251.xx] diagram (page 253)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-102.webp)
2 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.
![Lexmark 415 — [x]-page jam, clear manual feeder [251.xx] diagram (page 253)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/fig-253-1.webp)
3 Reload paper into the multipurpose feeder.
![Lexmark 415 — [x]-page jam, clear manual feeder [251.xx] diagram (page 253)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-103.webp)
Clearing jams 253
![Page 254 of the Lexmark 415 user manual — [x] ‑ page jam, open automatic feeder top cover. [28y.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-254.webp?w=400)
4 Slide the paper guide until it rests lightly against the edge of the paper stack.
![Lexmark 415 — [x]-page jam, open automatic feeder top cover. [28y.xx] diagram (page 254)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-104.webp)
to clear the message and continue printing. For non‑touch‑screen printer
5 From the printer control panel, touch
models, select Next > > Clear the jam, press OK > .
1 Remove all original documents from the ADF tray.
2 Open the ADF cover.
![Lexmark 415 — [x] ‑ page jam, open automatic feeder top cover. [28y.xx] diagram (page 254)](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/rimg-105.webp)
Clearing jams 254
![Page 255 of the Lexmark 415 user manual — [x]-page jam, open automatic feeder top cover. [28y.xx]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-255.webp?w=400)
3 Firmly grasp the jammed paper on each side, and then gently pull it out.
4 Close the ADF cover.
5 Straighten the edges of the original documents, then load the documents into the ADF, and then adjust the paper guide.
6 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > > Clear the jam, press OK > .
Clearing jams 255

Understanding the printer messages
Wait for the process to complete.
Try one or more of the following:
panel to clear the message and continue printing. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
panel to clear the message and continue printing. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
panel to clear the message and continue printing. For non‑touch‑screen printer models, press to confirm.
Make sure the right side cover is installed, and then close the front and top doors to clear the message.
Troubleshooting 256
![Page 257 of the Lexmark 415 user manual — Configuration change, some held jobs were not restored [57]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-257.webp?w=400)
Try one or more of the following:
You may need to order a toner cartridge. If necessary, select Continue to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to replace the toner cartridge very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
printer models, press to confirm.
Held jobs are invalidated because of any of the following possible changes in the printer:
Troubleshooting 257
![Page 258 of the Lexmark 415 user manual — Incompatible tray [x] [59]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-258.webp?w=400)
From the printer control panel, select Continue to clear the message. For non-touch-screen printer models, press to confirm.
Try one or more of the following:
printer models, press to confirm. • Cancel the current print job.
Try one or more of the following:
From the printer control panel, touch Format disk to format the printer hard disk and clear the message.
Error reading USB drive. Remove USB.
An unsupported USB device is inserted. Remove the USB device, and then insert a supported one.
Error reading USB hub. Remove hub.
An unsupported USB hub has been inserted. Remove the USB hub, and then install a supported one.
Remove, and then reinstall the indicated tray to clear the message.
Troubleshooting 258
![Page 259 of the Lexmark 415 user manual — Insufficient memory to support Resource Save feature [35]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-259.webp?w=400)
Try one or more of the following:
Insert the indicated tray into the printer.
Try one or more of the following:
The printer deleted some held jobs in order to process current jobs.
Select Continue to clear the message. For non-touch-screen printer models, press to confirm.
Try one or more of the following:
rest of the print job. For non‑touch‑screen printer models, press to confirm. • Cancel the current print job.
Install additional printer memory or select Continue on the printer control panel to disable Resource Save, clear the
message, and continue printing. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 259
![Page 260 of the Lexmark 415 user manual — Load [paper source] with [paper size]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-260.webp?w=400)
Try one or more of the following:
to confirm. • Delete other held jobs to free up additional printer memory.
Try one or more of the following:
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
For non‑touch‑screen printer models, press to confirm.
Troubleshooting 260
![Page 261 of the Lexmark 415 user manual — Load Manual Feeder with [paper type] [paper size]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-261.webp?w=400)
Try one or more of the following:
panel. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 261
![Page 262 of the Lexmark 415 user manual — Not enough free space in flash memory for resources [52]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-262.webp?w=400)
You may need to order a maintenance kit. For more information, contact customer support at http://support.lexmark.com or your service representative. If necessary, select Continue to clear the message and
continue printing. For non‑touch‑screen printer models, press to confirm.
For more information, contact customer support at http://support.lexmark.com or your service representative. If necessary, select Continue to clear the message and continue printing. For non‑touch‑screen printer models,
press to confirm.
You may need to replace the maintenance kit very soon. For more information, contact customer support at http://support.lexmark.com or your service representative.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
to confirm. • Install additional printer memory.
Try one or more of the following:
Try one or more of the following:
Troubleshooting 262
![Page 263 of the Lexmark 415 user manual — Reinstall missing or unresponsive [type] imaging kit [31.xy]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-263.webp?w=400)
The printer has detected a non‑Lexmark supply or part installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components.
All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.
To accept any and all of these risks, and to proceed with the use of non-genuine supplies or parts in your printer, press
and hold and the # button on the printer control panel simultaneously for 15 seconds.
For non‑touch‑screen printer models, press and simultaneously for 15 seconds to clear the message and continue printing.
If you do not wish to accept these risks, then remove the third-party supply or part from your printer, and then install a genuine Lexmark supply or part.
Try one or more of the following:
Try one or more of the following:
Troubleshooting 263
![Page 264 of the Lexmark 415 user manual — Replace [type] imaging kit, 0 estimated pages remain [84.xy]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-264.webp?w=400)
Try any of the following:
sheet. For non‑touch‑screen printer models, press to confirm. • Cancel the print job.
1 Remove any remaining packing material from the indicated location.
2 From the printer control panel, touch Continue to clear the message. For non‑touch‑screen printer models, press
to confirm.
Remove the paper stack from the standard bin.
Replace the indicated toner cartridge to clear the message and continue printing. For more information, see the instruction sheet that came with the supply.
Install a toner cartridge that matches the region number of the printer. x indicates the value of the printer region. y indicates the value of the cartridge region. x and y can have the following values:
1 United States, Canada
2 European Union (EU), European Economic Area (EEA), Switzerland
8 Rest of the world
![Page 265 of the Lexmark 415 user manual — Replace defective [type] imaging kit [31.xy]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-265.webp?w=400)
Replace the indicated imaging kit to clear the message and continue printing. For more information, see the instruction sheet that came with the supply.
Replace all originals if restarting job.
Try one or more of the following:
Remove and replace the defective printer hard disk.
Replace the defective toner cartridge to clear the message. For more information, see the instruction sheet that came with the supply.
Replace the defective imaging kit to clear the message and continue printing. For more information, see the instruction sheet that came with the supply.
Replace jammed originals if restarting job.
Try one or more of the following:
Troubleshooting 265
![Page 266 of the Lexmark 415 user manual — Replace waste toner bottle [82.xy]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-266.webp?w=400)
Contact customer support at http://support.lexmark.com or your service representative, and then report the message. The printer is scheduled for maintenance.
Install the indicated toner cartridge to clear the message. For more information, see the “Replacing supplies” section of the User’s Guide.
Install the indicated imaging kit to clear the message. For more information, see the “Replacing supplies” section of the User’s Guide.
Install the missing waste toner bottle to clear the message. For more information, see the instruction sheet that came with the supply.
Remove the toner cartridge, and then install a supported one to clear the message.
Remove the indicated imaging kit, and then install a supported one to clear the message.
Replace the waste toner bottle to clear the message.
Troubleshooting 266

Try one or more of the following:
non‑touch‑screen printer models, press to confirm. • Select Do not restore if you do not want any print jobs to be restored. For non‑touch‑screen printer models, press
to confirm.
Close the ADF cover.
Print without the scanner, or contact your system support person.
From the printer control panel, try one or more of the following:
Remove the jammed paper from the scanner.
Remove the jammed paper from the scanner.
From the printer control panel, select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 267
![Page 268 of the Lexmark 415 user manual — Too many flash options installed [58]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-268.webp?w=400)
SMTP server not set up. Contact system administrator.
From the printer control panel, select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
From the printer control panel, select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
are needed to continue processing the current job. For non‑touch‑screen printer models, press to clear the message and continue printing.
1 Order the missing supply immediately. 2 Install the supply. For more information, see the instruction sheet that came with the supply. • Cancel the print job, then install the missing supply, and then resend the print job.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra flash memory.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Troubleshooting 268
![Page 269 of the Lexmark 415 user manual — Waste toner bottle nearly full [82.xy]](/cdn/reader/82/828233be67d652f25b27890fb7af6ae55b85140517cc951a003ec89c99ccf32f/images/page-269.webp?w=400)
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra trays.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
You may need to order an imaging kit. If necessary, select Continue on the printer control panel to clear the message
and continue printing. For non‑touch‑screen printer models, press to confirm.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to replace the imaging kit very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
printer models, press to confirm. • Format the flash memory.
You may need to order a waste toner bottle. If necessary, select Continue on the printer control panel to clear the
message and continue printing. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 269

Weblink server not set up. Contact system administrator.
Select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Go to step 2. Turn on the printer.
Make sure the printer is turned on.
Is the printer turned on?
Press the Sleep button to wake the printer from Sleep mode or Hibernate mode.
Go to step 3.
Check if the printer is in Sleep mode or Hibernate mode.
Is the printer in Sleep mode or Hibernate mode?
Go to step 4. Plug one end of the power cord into the printer and the other to a properly grounded electrical outlet.
Check if one end of the power cord is plugged into the printer and the other to a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
Unplug the other electrical equipment, and then turn on the printer. If the printer does not work, then reconnect the other electrical equipment.
Go to step 5.
Check other electrical equipment plugged into the electrical outlet.
Does other electrical equipment work?

Go to step 6. Make sure to match the following:
Check if the cables connecting the printer and the computer are inserted in the correct ports.
Are the cables inserted in the correct ports?
Step 6 Make sure the electrical outlet is not turned off by a switch or breaker.
Turn on the switch or reset the breaker.
Go to step 7.
Is the electrical outlet turned off by a switch or breaker?
Connect the printer power cord directly to a properly grounded electrical outlet.
Go to step 8.
Check if the printer is plugged into any surge protectors, uninterruptible power supplies, or extension cords.
Is the printer plugged into any surge protectors, uninterruptible power supplies, or extension cords?
Step 8 Check if one end of the printer cable is plugged into a port on the printer and the other to the computer, print server, option, or other network device.
Go to step 9. Connect the printer cable securely to the printer and the computer, print server, option, or other network device.
Is the printer cable securely attached to the printer and the computer, print server, option, or other network device?
Go to step 10. Turn off the printer, remove all packing materials, then reinstall the hardware options, and then turn on the printer.
Make sure to install all hardware options properly and remove any packing material.
Are all hardware options properly installed and all packing material removed?
Go to step 11. Use correct printer driver settings.
Check if you have selected the correct port settings in the printer driver.
Are the port settings correct?
Go to step 12. Install the correct printer driver.
Check the installed printer driver.
Is the correct printer driver installed?
The problem is solved. Contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Is the printer working?

The problem is solved. Go to step 2.
Press the Sleep button on the printer control panel.
Does Ready appear on the printer display?
The problem is solved. Turn off the printer, and then contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Do Please wait and Ready appear on the printer display?
The problem is solved. Go to step 2.
Turn off the printer, then wait for about 10 seconds, and then turn on the printer.
Does the internal option operate correctly?
Go to step 3. Connect the internal option to the controller board.
Check if the internal option is properly installed in the controller board.
a Turn off the printer using the power switch, and then unplug the power
cord from the electrical outlet. b Make sure the internal option is installed in the appropriate connector
in the controller board. c Connect the power cord to the printer, then to a properly grounded
electrical outlet, and then turn on the printer.
Is the internal option properly installed in the controller board?
Go to step 4. Reinstall the internal option.
Print a menu settings page, and then check to see if the internal option is listed in the Installed Features list.
Is the internal option listed in the menu settings page?

The problem is solved. Contact customer support.
a Check if the internal option is selected.
It may be necessary to manually add the internal option in the printer driver to make it available for print jobs. For more information, see “Updating available options in the printer driver” on page 37. b Resend the print job.
Does the internal option operate correctly?
Make sure the memory card is installed.
The problem is solved. Contact customer support.
a Install the memory card. For more information, see “Installing a
memory card” on page 29.
Installed Options list.
Is the card listed in the Installed Options list?
The problem is solved. Go to step 2.
a Pull out the tray, and then do one or more of the following:
Is the tray working?
The problem is solved. Go to step 3.
a Turn off the printer, then wait about 10 seconds, and then turn the
printer back on. b Resend the print job.
Is the tray working?

Go to step 4. Reinstall the tray. For more information, see the setup documentation that came with the tray.
Check if the tray is installed and recognized by the printer.
Print a menu settings page, and then check if the tray is listed in the Installed Features list.
Is the tray listed in the menu settings page?
The problem is solved. Contact customer support.
Check if the tray is available in the printer driver.
Is the tray available in the printer driver?
Turn on Jam Recovery.
The problem is solved. Contact customer support.
a From the home screen, navigate to:
> Settings > General Settings > Print Recovery b From the Jam Recovery menu, touch the arrows to scroll to On or
Auto. c Touch Submit.
Do pages reprint after a jam?

Go to step 2. The problem is solved.
a Pull out the tray, and then do one or more of the following:
If jam recovery is enabled, then the print jobs will reprint automatically.
Do paper jams still occur frequently?
Go to step 3. The problem is solved.
a Load paper from a fresh package.
Do paper jams still occur frequently?
Contact customer support.
The problem is solved.
a Review the tips on avoiding jams. For more information, see “Avoiding
jams” on page 240. b Follow the recommendations, and then resend the print job.
Do paper jams still occur frequently?
Check the entire paper path for jammed paper.
Contact customer support.
The problem is solved.
a Remove any jammed paper. b From the printer control panel, touch Continue to clear the message.
Does the paper jam message remain?

Go to step 2. Select one of the Print and Hold options, and then resend the print job. For more information, see “Printing confidential and other held jobs” on page 70.
Open the held jobs folder on the printer display, and then verify that your print job is listed.
Is your print job listed in the held jobs folder?
Step 2 The print job may contain a formatting error or invalid data.
The problem is solved. Go to step 3.
If you are printing from the Internet, then the printer may be reading multiple job titles as duplicates and deleting all jobs except the first one.
a Open the Print Properties folder. b From the Print and Hold dialog, select the “Keep duplicate documents”
check box. c Enter a PIN number.
For Macintosh users Save each print job, name each job differently, and then send the individual jobs to the printer.
Does the job print?
The problem is solved. Add additional printer memory.
Free up additional printer memory by deleting some of the held jobs.
Does the job print?

Go to step 2. Insert the flash drive into the front USB port.
Check if the flash drive is inserted into the front USB port.
Is the flash drive inserted into the front USB port?
Wait until the printer is ready, then view the held jobs list, and then print the documents.
Go to step 3.
Check if the indicator light on the printer control panel is blinking green.
Is the indicator light blinking green?
Go to step 4. The problem is solved.
a Check for an error message on the display. b Clear the message.
Does the error message still appear?
Go to step 5. The problem is solved.
Check if the flash drive is supported.
For more information on tested and approved USB flash drives, see “Supported flash drives and file types” on page 68.
Does the error message still appear?
Contact customer support.
The problem is solved.
Check if the USB port is disabled by the system support person.
Does the error message still appear?
Deactivate Hex Trace mode.
Go to step 2.
Make sure the printer is not in Hex Trace mode.
Is the printer in Hex Trace mode?
Contact customer support.
The problem is solved.
a From the printer control panel, select Standard Network or
Network [x], and then set SmartSwitch to On. b Resend the print job.
Do incorrect characters print?

The problem is solved. Go to step 2.
a Check if you are printing on paper that is supported by the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 3.
a From the Paper menu on the printer control panel, set the paper size
and type to match the paper loaded in the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 4.
a Depending on your operating system, open Printing Preferences or
the Print dialog, and then specify the paper type. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Contact customer support.
a Check if the trays are not linked. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 2.
a From the Finishing menu on the printer control panel, set Collate to
(1,2,3) (1,2,3). b Resend the print job.
Did the job print and collate correctly?
The problem is solved. Go to step 3.
a From the printer software, set Collate to (1,2,3) (1,2,3).
Did the job print and collate correctly?

The problem is solved. Contact customer support.
Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Did the job print and collate correctly?
Multiple‑language PDF files do not print
The problem is solved. Go to step 2.
a Check if the print options for the PDF output are set to embed all fonts.
For more information, see the documentation that came with Adobe Acrobat. b Generate a new PDF file, and then resend the print job.
Do the files print?
The problem is solved. Contact customer support.
a Open the document you want to print in Adobe Acrobat. b Click File > Print > Advanced > Print As Image > OK > OK.
Do the files print?
Place letter‑ or A4‑size paper in the tray, and then resend the print job. Does the print speed increase?
The problem is solved. Contact customer
support.

The problem is solved. Go to step 2.
a From the document you are trying to print, open the Print dialog and
check if you have selected the correct printer.
Do the jobs print?
The problem is solved. Go to step 3.
a Check if the printer is plugged in and turned on, and if Ready appears
on the printer display. b Resend the print job.
Do the jobs print?
Step 3 If an error message appears on the printer display, then clear the message.
The problem is solved. Go to step 4.
Do the jobs print?
The problem is solved. Go to step 5.
a Check if the ports (USB, serial, or Ethernet) are working and if the
cables are securely connected to the computer and the printer.
Do the jobs print?
The problem is solved. Go to step 6.
a Turn off the printer, then wait for about 10 seconds, and then turn the
printer back on. b Resend the print job.
Do the jobs print?
The problem is solved. Contact customer support.
a Remove, and then reinstall the printer software. For more
information, see “Installing the printer software” on page 36.
Do the jobs print?

The problem is solved. Go to step 2.
Change the environmental settings of the printer.
a From the printer control panel, navigate to:
Settings > General Settings b Select Eco‑Mode or Quiet Mode, and then select Off.
Did the job print?
The problem is solved. Go to step 3.
Reduce the number and size of fonts, the number and complexity of images, and the number of pages in the print job, and then resend the job
Did the job print?
The problem is solved. Go to step 4.
a Remove held jobs stored in the printer memory. b Resend the print job.
Did the job print?
The problem is solved. Go to step 5.
a Disable the Page Protect feature.
From the printer control panel, navigate to: Settings > General Settings > Print Recovery > Page Protect > Off b Resend the print job.
Did the job print?
The problem is solved. Go to step 6.
a Check if the cable connections to the printer and print server are
secure. For more information, see the setup documentation that came with the printer. b Resend the print job.
Did the job print?
The problem is solved. Contact customer support.
Install additional printer memory, and then resend the print job.
Did the job print?

The problem is solved. Go to step 2.
a Open the trays, and then check if they contain paper of the same size
and type.
Do the trays link correctly?
The problem is solved. Contact customer support.
a From the printer control panel, set the paper size and type in the Paper
menu to match the paper loaded in the trays to be linked.
Do the trays link correctly?
Increase the printing timeout.
The problem is solved. Check the original file for manual page breaks.
a From the home screen, navigate to:
> Settings > General Settings > Timeouts b Increase the Print Timeout setting, and then touch Submit.
c Resend the print job.
Did the file print correctly?


Go to step 2. Select a font that is supported by the printer.
a Print a font sample list to check if the fonts you are using are supported
Menus > Reports > Print Fonts 2 Select PCL Fonts or PostScript Fonts. b Resend the print job.
Are you using fonts that are supported by the printer?
Check if the fonts installed on the computer are supported by the printer.
Are the fonts installed on the computer supported by the printer?

a Move the width and length guides in the tray to the correct positions
for the paper loaded. b Resend the print job.
Troubleshooting 283

Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Does the paper size match the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.
Is the page or image clipped?
Contact customer support.
The problem is solved.
a Remove, and then reinstall the imaging kit.
Is the page or image clipped?
ABCDE
ABCDE ABCDE


a From the Quality menu on the printer control panel, reduce the toner

a Make sure your software program is using a correct fill pattern. b Resend the print job.
a Load the specified tray or feeder with a recommended type of paper. b Resend the print job.
Troubleshooting 285

Go to step 4. The problem is solved.
a Remove, and then reinstall the imaging kit.
Do horizontal voids appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do horizontal voids appear on prints?
ABCD ABCD ABCD
The problem is solved. Go to step 2.
a Move the width and length guides in the tray to the correct positions
for the paper size loaded. b Resend the print job.
Are the margins correct?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size in the Paper menu to match the paper loaded in the tray.
Does the paper size match the paper loaded in the tray?

The problem is solved. Contact customer support.
a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.
Are the margins correct?
Go to step 2. Adjust the width and length guides.
Move the width and length guides in the tray to the correct positions for the size of the paper loaded.
Are the width and length guides positioned correctly?
Go to step 3. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the paper still curled?
Go to step 5. The problem is solved.
a Remove the paper from the tray, and then turn it over. b Resend the print job.
Is the paper still curled?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Is the paper still curled?

) ) ABCDE
ABCDE ABCDE
Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded in the tray. b Resend the print job.
Do print irregularities still appear?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Is the tray set to the size and type of the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do print irregularities still appear?
Step 4 Check if the paper loaded in the tray has texture or rough finishes.
From the printer control panel, set the paper texture in the Paper menu to match the paper loaded in the tray.
Go to step 5.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Do print irregularities still appear?

Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do print irregularities still appear?
Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, select Color
Adjust. b Resend the print job.
Is the print still too dark?
Go to step 3. The problem is solved.
a From the Quality menu on the printer control panel, reduce the toner
darkness.
Is the print still too dark?
Go to step 4. Change the paper loaded in the tray to match the paper type, texture, and weight specified in the tray settings.
a From the printer control panel, set the paper type, texture, and weight
in the Paper menu to match the paper loaded in the tray. b Resend the print job.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 5. The problem is solved.
a Depending on your operating system, specify the paper type, texture
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too dark?

From the printer control panel, set the paper texture in the Paper menu to match the paper loaded on the tray.
Go to step 6.
Check if the paper loaded in the tray has texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 7. The problem is solved.
a Load paper from a fresh package.
Is the print still too dark?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Is the print still too dark?
Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, select Color
Adjust. b Resend the print job.
Is the print still too light?
Go to step 3. The problem is solved.
a From the Quality menu on the printer control panel, increase the toner
darkness.
Is the print still too light?

Go to step 4. Specify the paper type, texture, and weight from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper type, texture, and weight in the Paper menu to match the paper loaded in the tray.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 5. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too light?
From the printer control panel, set the paper texture in the Paper menu to match the paper loaded in the tray
Go to step 5.
Make sure that the paper has no texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 7. The problem is solved.
a Load paper from a fresh package.
Is the print still too light?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Is the print still too light?

Go to step 2. The problem is solved.
a Check if there is packing material left on the imaging kit.
1 Remove the imaging kit. 2 Check if the packing material is properly removed from the imaging kit.
Is the printer still printing blank pages?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Is the printer still printing blank pages?
Go to step 2. The problem is solved.
a Remove, and then reinstall the imaging kit.
Is the printer printing solid black pages?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Is the printer printing solid black pages?


Go to step 2. 1 Check if the distance between the defects is equal to one of the following:
Check for a distance between the defects that equals:
Is the distance between defects equal to one of the listed measurements?
Replace the imaging kit, and then resend the print job.

Troubleshooting 293 · Leading edge · Trailing edge

Go to step 2. Load paper with the correct paper type and weight in the tray.
Check if the paper loaded in the tray has the correct paper type and weight.
Is paper with the correct paper type and weight loaded in the tray?
Go to step 3. Change the paper type and weight to match the paper loaded in the tray.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the printer settings match the type and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do shadow images still appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do shadow images still appear on prints?
) ) ABCDE
ABCDE ABCDE
Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded. b Resend the print job.
Is the print still skewed?
Contact customer support.
The problem is solved.
a Check if you are printing on a paper that is supported by the tray. b Resend the print job.
Is the print still skewed?

ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the tray or feeder from
Printing Preferences or the Print dialog. b Resend the print job.
Do streaked horizontal lines appear on prints?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the paper in the tray?
Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked horizontal lines appear on prints?


Replace the imaging kit, and then resend the print job.
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do streaked vertical lines appear on prints?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper texture, type, and weight in the Paper menu to match the paper loaded in the tray.
Do the paper texture, type, and weight match the paper in the tray?

Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked vertical lines appear on prints?
Go to step 5. The problem is solved.
a Remove, and then reinstall the imaging kit.
Do streaked vertical lines appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do streaked vertical lines appear on prints?
ABCDE
ABCDE ABCDE
The problem is solved. Go to step 2.
a Remove, and then reinstall the imaging kit.
Does fog or shading disappear from the prints?


Replace the imaging kit, and then resend the print job.

Go to step 2. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
From the Paper menu on the printer control panel, check the paper type and weight.
Do the paper type and texture match the paper loaded in the tray?
From the Paper menu on the printer control panel, set the paper texture.
Check if you are printing on paper with texture or rough finishes.

Replace the imaging kit, and then resend the print job.
Troubleshooting 298


Go to step 2. Set the paper type to Transparency.
From the printer control panel, set the paper type in the Paper menu to match the paper loaded in the tray.
Is the paper type for the tray set to Transparency?
a Check if you are using a recommended type of transparency. b Resend the print job.

Replace the imaging kit, and then resend the print job.

a Check if your software program is using a correct fill pattern. b Resend the print job.
Troubleshooting 299

Go to step 3. The problem is solved.
a From the Paper Menu on the printer control panel, check the paper
type and paper weight. b Resend the print job.
Do vertical voids appear on prints?
Go to step 4. The problem is solved.
Check if you are using a recommended type of paper.
a Load paper source with a recommended type of paper. b Resend the print job.
Do vertical voids appear on prints?
Go to step 5. The problem is solved.
a Remove, and then reinstall the imaging kit.
Do vertical voids appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do vertical voids appear on prints?
What is RGB color?
Red, green, and blue light can be added together in various amounts to produce a large range of colors observed in nature. For example, red and green can be combined to create yellow. Televisions and computer monitors create colors in this manner. RGB color is a method of describing colors by indicating the amount of red, green, or blue needed to produce a certain color.
What is CMYK color?
Cyan, magenta, yellow, and black inks or toners can be printed in various amounts to produce a large range of colors observed in nature. For example, cyan and yellow can be combined to create green. Printing presses, inkjet printers, and color laser printers create colors in this manner. CMYK color is a method of describing colors by indicating the amount of cyan, magenta, yellow, and black needed to reproduce a particular color.

How is color specified in a document to be printed?
Software programs typically specify the document color using RGB or CMYK color combinations. Additionally, they let users modify the color of each object in a document. For more information, see the help information of your operating system.
How does the printer know what color to print?
When a user prints a document, information describing the type and color of each object is sent to the printer. The color information is passed through color conversion tables that translate the color into the appropriate amounts of cyan, magenta, yellow, and black toner needed to produce the color you want. The object information determines the application of color conversion tables. For example, it is possible to apply one type of color conversion table to text while applying a different color conversion table to photographic images.
What is manual color correction?
When manual color correction is enabled, the printer employs user‑selected color conversion tables to process objects. However, Color Correction must be set to Manual, or no user‑defined color conversion will be implemented. Manual color correction settings are specific to the type of object being printed (text, graphics, or images), and how the color of the object is specified in the software program (RGB or CMYK combinations).
To manually apply a different color conversion table, do the following:
1 From the Quality menu on the printer control panel, select Color Correction, and then select Manual.
2 From the Quality menu on the printer control panel, select Manual Color, and then select the appropriate color conversion table for the affected object type.
Object type Color conversion tables
RGB Image RGB Text
Troubleshooting 301 · RGB Graphics

Object type Color conversion tables
How can I match a particular color (such as a corporate logo)?
Nine types of Color Samples sets are available from the Quality menu on the printer control panel. These are also available from the Color Samples page of the Embedded Web Server. Selecting any sample set generates a multiple‑page printout consisting of hundreds of colored boxes. Either a CMYK or RGB combination is located on each box, depending on the table selected. The observed color of each box is obtained by passing the CMYK or RGB combination labeled on the box through the selected color conversion table.
By examining Color Samples sets, you can identify the box whose color is the closest to the color you want. The color combination labeled on the box can then be used for modifying the color of the object in a software program. For more information, see the help information of your operating system.
Selecting which Color Samples set to use for a particular color‑matching problem depends on the Color Correction setting being used , the type of object being printed, and how the color of the object is specified in the software program. When Color Correction is set to Off, the color is based on the print job information, and no color conversion is implemented.
Note: The Color Samples pages are not useful if the software program does not specify colors with RGB or CMYK combinations. Additionally, certain situations exist in which the software program or the computer operating system adjusts the RGB or CMYK combinations specified in the program through color management. The resulting printed color may not be an exact match of the Color Samples pages.
Go to step 2. Set the paper type to Transparency.
From the printer control panel, make sure the paper type setting is set to Transparency.
Is the paper type setting correct?
The problem is solved. Go to step 3.
Reduce the toner darkness, and then resend the print job.
Does the print on the color transparency look lighter?

The problem is solved. Contact customer support.
Make sure you are using a recommended type of color transparency, and then resend the print job.
Does the print on the color transparency look lighter?
The color of the print does not match the color of the original file
The problem is solved. Go to step 2.
a Set Color Correction to Off.
Does the color of the print match the color of the file on the computer screen?
The problem is solved. Contact customer support.
From the Quality menu on the printer control panel, do the following:
a Select Color Correction, and then select Manual. b Select Manual Color, and then select the appropriate color conversion
table for the affected object type. c Resend the print job.
Does the color of the print match the color of the file on the computer screen?
Adjust the color balance.
The problem is solved. Contact customer support.
a From the Color Balance menu on the printer control panel, increase
or decrease the values for cyan, magenta, yellow, and black. b Resend the print job.
Does the print still appear tinted?

Clear the error or status message.
Go to step 2.
Check if an error or status message appears on the display.
Does an error or status message appear?
Go to step 3. Connect the power cord to the printer and a properly grounded electrical outlet.
Check if the power cord is plugged into the printer and a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
The problem is solved. Contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn it back on.
Did Performing Self Test and Ready appear?
Check if there are no obstructions between the scanner unit and the printer.
The problem is solved. Contact customer support.
a Lift the scanner unit. b Remove any obstruction that keeps the scanner unit open.
c Lower the scanner unit.
Did the scanner unit close properly?

Clear the error or status message.
Go to step 2.
Check if an error or status message appears on the display.
Does an error or status message appear?
Go to step 3. Increase the scan resolution setting for a higher‑quality output.
Check the quality of the original document.
Is the quality of the original document satisfactory?
Go to step 4. See “Cleaning the scanner glass” on page 211.
If dark marks appear on prints, then clean the scanner glass and the ADF glass using a clean, lint-free cloth dampened with water.
Is the scanner glass clean?
Go to step 5. See “Print quality problems” on page 283.
Send a print job, and then check for print quality problems.
a From the General Settings menu, adjust the Eco‑Mode settings. b From the Copy menu, adjust the Darkness setting.
c If the print remains faded, then replace the toner cartridge.
Is the print quality satisfactory?
Go to step 6. Place the document or photo facedown on the scanner glass in the upper left corner.
Check the placement of the document or photo.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Is the document or photo loaded correctly?
Go to step 7. Change the Content Type and Content Source settings to match the document being scanned.
Check the copy settings.
From the Copy screen, check if the Content Type and Content Source settings are correct for the document being scanned.
Are the Content Type and Content Source settings correct for the document being scanned?
Step 7 Check for patterns on print.
Go to step 8. The problem is solved.
a From the printer control panel, navigate to:
Copy > Sharpness > select a lower setting
Do patterns appear on prints?

Go to step 9. The problem is solved.
Check for missing or faded text on prints.
a From the Copy screen, adjust the settings of the following:
Do prints have missing or faded text?
Contact customer support.
The problem is solved.
Check for washed‑out or overexposed output.
a From the Copy screen, adjust the settings of the following:
Do pages show washed‑out or overexposed prints?
Go to step 2. Place the document or photo facedown on the scanner glass in the upper left corner.
Check the placement of the document or photo.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Is the document or photo loaded correctly?
Go to step 3. Change the paper size setting to match the paper loaded in the tray, or load the tray with paper that matches the paper size setting.
Check if the paper size setting matches the size of the paper loaded in the tray.
From the Paper menu on the printer control panel, check the Paper Size setting.
Does the paper size setting match the size of the paper loaded in the tray.
The problem is solved. Contact customer support.
a Specify the paper size. Depending on your operating system, specify
the paper size in Printing Preferences or the Print dialog. b Resend the print job.
Do copies print properly?

Contact your telephone company to check if your telephone line is subscribed to the caller ID service.
The problem is solved. Contact customer support.
Does the caller ID appear?
Clear the error or status message.
Go to step 2.
Check if an error or status message appears on the display.
Is there an error or status message on the display?
Step 2 Check if the power cord is plugged into the printer and a properly grounded electrical outlet.
Go to step 3. Connect the power cord to the printer and a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
Go to step 4. Turn on the printer, and then wait until Ready appears on the display.
Check the power.
Check if the printer is plugged in and turned on, and if Ready appears on the display.
Is the printer turned on, and does Ready appear on the display?

Go to step 5. Securely connect the cables.
Check the printer connections.
If applicable, check if the cable connections for the following equipment are secure:
Are the cable connections secure?
The problem is solved. Go to step 6.
a Check the telephone wall jack.
1 Plug the telephone cable into the wall jack. 2 Listen for a dial tone. 3 If you do not hear a dial tone, then plug a different telephone cable into the wall jack. 4 If you still do not hear a dial tone, then plug the telephone cable into a different wall jack. 5 If you hear a dial tone, then connect the printer to that wall jack. b Try sending or receiving a fax.
Can you send or receive a fax?
Go to step 7. Connect the printer to an analog phone service or the correct digital connector.
Check if the printer is connected to an analog phone service or the correct digital connector.
The fax modem is an analog device. Certain devices can be connected to the printer so that digital telephone services can be used.
Is the printer connected to an analog phone service or the correct digital connector?

Check for a dial tone.
Did you hear a dial tone?
The problem is solved. Go to step 9.
Temporarily disconnect other equipment (such as answering machines, computers with modems, or telephone line splitters) between the printer and the telephone line, and then try sending or receiving a fax.
Can you send or receive a fax?
The problem is solved. Go to step 10.
a Temporarily disable call waiting. Contact your telephone company to
obtain the keypad sequence for temporarily disabling call waiting. b Try sending or receiving a fax.
Can you send or receive a fax?
The problem is solved. Go to step 11.
a Temporarily disable voice mail service. For more information, contact
your telephone company.
Can you send or receive a fax?
The problem is solved. Contact customer support.
Scan the original document one page at a time.
a Dial the fax number. b Scan the document one page at a time.
Can you send or receive a fax?

The problem is solved. Go to step 2.
Check the tray or feeder.
If empty, then load paper in the tray or feeder.
Can you receive faxes?
The problem is solved. Go to step 3.
Check the ring count delay settings.
a Open a Web browser, and then type the printer IP address in the
address field.
c In the “Rings to Answer” field, enter the number of times you want
the phone to ring before the printer answers. d Click Submit.
Can you receive faxes?
The problem is solved. Contact customer support.
Replace the toner cartridge. For more information, see the instruction sheet that came with the supply.
Can you receive faxes?
The problem is solved. Go to step 2.
Check if the printer is in Fax mode.
From the home screen, touch Fax to put the printer in Fax mode, and then send the fax.
Can you send faxes?

The problem is solved. Go to step 3.
Load the original document properly.
Load the original document faceup, short edge first into the ADF tray or facedown on the scanner glass in the upper left corner.
Can you send faxes?
Step 3 Set up the shortcut number properly.
The problem is solved. Contact customer support.
Can you send faxes?
a From the home screen, navigate to:
The problem is solved. Contact customer support.
> Settings > General Settings > Run initial setup > Yes > Submit b Turn off the printer, and then turn it back on.
The “Select your language” screen appears on the printer display.
. d Select a country or region, and then touch Next. e Select a time zone, and then touch Next.
c Select a language, and then touch
f Select Fax and E‑mail, and then touch Next.
Are fax and e‑mail functions set up?

The problem is solved. Go to step 2.
Ask the person who sent you the fax to:
a Check if the quality of the original document is satisfactory. b Increase the fax scan resolution, if possible.
c Resend the fax.
Is the fax print quality satisfactory?
The problem is solved. Go to step 3.
Decrease the incoming fax transmission speed.
a Open a Web browser, and then type the printer IP address in the
address field.
c In the Max Speed menu, click one of the following:
Is the fax print quality satisfactory?
The problem is solved. Contact customer support.
Replace the toner cartridge.
When Cartridge low [88.xy] appears, replace the cartridge, and then resend the fax.
Is the fax print quality satisfactory?

Go to step 2. Turn on the printer.
Check if the printer is turned on.
Is the printer turned on?
Go to step 3. Connect the printer cable securely to the printer and the computer, print server, option, or other network device.
Check if the printer cable is securely attached to the printer and the computer, print server, option, or other network device.
Is the printer cable securely attached to the printer and the computer, print server, option, or other network device?
Go to step 4. Connect the power cord to the printer and a properly grounded electrical outlet.
Check if the power cord is plugged into the printer and a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
Turn on the switch or reset the breaker.
Go to step 5.
Check if the electrical outlet is turned off by a switch or breaker.
Is the electrical outlet turned off by a switch or breaker?
Connect the printer power cord directly to a properly grounded electrical outlet.
Go to step 6.
Check if the printer is plugged into any surge protectors, uninterruptible power supplies, or extension cords.
Is the printer plugged into any surge protectors, uninterruptible power supplies, or extension cords?
Unplug the other electrical equipment and turn on the printer. If the printer does not work, then reconnect the other electrical equipment and then go to step 6.
Go to step 7.
Check other electrical equipment plugged into the outlet.
Are the other electrical equipment working?

The problem is solved. Contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Are the printer and scanner working?
Go to step 2. Connect the cables properly.
Check the cable connections.
Make sure the Ethernet or USB cable is securely connected to the computer and the printer.
Are the cables securely connected?
Change the file name. Go to step 3.
Check if the file name is already in use.
Is the file name already in use?
Step 3 Check if the document or photo you want to scan is open in another application or being used by another user.
Close the file you are scanning.
Go to step 4.
Is the file you want to scan open by another application or user?
Step 4 Check if either the Append time stamp or the Overwrite existing file check box is selected in the destination configuration settings.
Contact customer support.
Select the Append time stamp or Overwrite existing file check box in the destination configuration settings.
Is the Append time stamp or Overwrite existing file check box selected in the destination configuration settings?
Check if there are obstructions in the scanner unit.
The problem is solved. Contact customer support.
a Lift the scanner unit. b Remove any obstruction keeping the scanner unit open.
c Lower the scanner unit.
Did the scanner unit close correctly?

Go to step 2. The problem is solved.
Check if other applications are interfering with the scan.
Close all applications that are not being used.
Does scanning still take too long or freeze the computer?
Contact customer support.
The problem is solved.
Select a lower scan resolution.
Does scanning still take too long or freeze the computer?
Step 1 Check if an error message appears on the display.
Clear the error message.
Go to step 2.
Is there an error message on the printer display?
Go to step 3. Increase the scan resolution settings for a higher‑quality output.
Check the quality of the original document.
Is the quality of the original document satisfactory?
Go to step 4. See “Cleaning the scanner glass” on page 211.
Clean the scanner glass and the ADF glass using a clean, lint‑free cloth dampened with water.
Is the scanner glass clean?
Go to step 5. Place the document or photo facedown on the scanner glass in the upper left corner.
Check the placement of the document or photo.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Is the document or photo loaded correctly?
Go to step 6. See “Print quality problems” on page 283.
Send a print job, and then check for print quality problems.
Is the print quality satisfactory?

Go to step 7. Change the Content Type and Content Source settings to match the document being scanned.
Check the scan settings.
From the Scan screen, make sure the Content Type and Content Source settings are correct for the document being scanned.
Are the Content Type and Content Source settings correct for the document being scanned?
Problem solved. Contact customer support.
Increase the scan resolution settings for a higher‑quality output.
Did the increased resolution produce a higher‑quality output?
Check the placement of the document or photo.
Contact customer support.
Load the document or photo facedown on the scanner glass in the upper left corner.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Is the document or photo loaded correctly?
Go to step 3. Go to step 2.
Make sure the printer is turned on and that Ready appears on the printer display before scanning a job.
Does Ready appear before scanning the job?
Clear the error message.
Go to step 3.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Is there an error message on the printer display?
Contact customer support.
Tighten the cable connections.
Check the cable connections between the printer and the print server to make sure they are secure.
For more information, see the setup documentation that came with the printer.
Are the cable connections between the printer and the print server secure?

Step 1 Check the system log for relevant details.
Go to step 2. Contact customer support.
a Open a Web browser, and then type the printer IP address in the
address field.
If you do not know the IP address of the printer, then you can:
c From the Filter menu, select an application status. d From the Application menu, select an application, and then click
Submit.
Does an error message appear in the log?
Step 2 Resolve the error.
The problem is solved. Contact customer support.
Is the application working now?
The problem is solved. Go to step 2.
a Turn on the printer. b Open a Web browser, and then type the printer IP address.
c Press Enter.
Does the Embedded Web Server open?

The problem is solved. Go to step 3.
Make sure the printer IP address is correct.
a View the printer IP address:
Does the Embedded Web Server open?
Step 3 Check if the network is working.
The problem is solved. Go to step 4.
a Print a network setup page. b Check the first section of the network setup page and confirm that the
status is Connected.
Does the Embedded Web Server open?
The problem is solved. Go to step 5.
Check if the cable connections to the printer and print server are secure.
a Connect the cables properly. For more information, see the setup
documentation that came with the printer. b Open a Web browser, and then type the printer IP address.
c Press Enter.
Does the Embedded Web Server open?
The problem is solved. Contact your system support person.
Temporarily disable the Web proxy servers.
Proxy servers may block or restrict you from accessing certain Web sites including the Embedded Web Server.
Does the Embedded Web Server open?

When you contact customer support, you will need to be able to describe the problem you are experiencing, the message on the printer display, and the troubleshooting steps you have already taken to find a solution.
You need to know your printer model type and serial number. For more information, see the label at the back of the printer. The serial number is also listed on the menu settings page.
Lexmark has various ways to help you solve your printing problem. Visit the Lexmark Web site at http://support.lexmark.com, and then select one of the following:
Tech Library You can browse our library of manuals, support documentation, drivers, and other downloads to help you
solve common problems.
E-mail You can send an e-mail to the Lexmark team, describing your problem. A service representative will respond and provide you with information to solve your problem.
Live chat You can chat directly with a service representative. They can work with you to solve your printer problem or provide assistance through Assisted Service where the service representative can remotely connect to your computer through the Internet to troubleshoot problems, install updates, or complete other tasks to help you successfully use your Lexmark product.
Telephone support is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, visit http://support.lexmark.com.
Troubleshooting 319

Product name:
Lexmark CX410e and CX410de
Machine type:
Model(s):
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
© 2012 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
415, 436 · October 2012

All licensing notices associated with this product can be viewed from the root directory of the installation software CD.
Lexmark, Lexmark with diamond design, MarkNet, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
The following terms are trademarks or registered trademarks of these companies:
Albertus The Monotype Corporation plc
Antique Olive Monsieur Marcel OLIVE
Apple-Chancery Apple Computer, Inc.
Arial The Monotype Corporation plc
CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Agfa Corporation
Chicago Apple Computer, Inc.
Clarendon Linotype-Hell AG and/or its subsidiaries
Geneva Apple Computer, Inc.
GillSans The Monotype Corporation plc
Helvetica Linotype-Hell AG and/or its subsidiaries
Hoefler Jonathan Hoefler Type Foundry
ITC Avant Garde Gothic International Typeface Corporation
ITC Bookman International Typeface Corporation
ITC Mona Lisa International Typeface Corporation
ITC Zapf Chancery International Typeface Corporation
Joanna The Monotype Corporation plc
Monaco Apple Computer, Inc.
New York Apple Computer, Inc.
Palatino Linotype-Hell AG and/or its subsidiaries
Stempel Garamond Linotype-Hell AG and/or its subsidiaries
Eurostile Nebiolo · Marigold Arthur Baker · Oxford Arthur Baker

Times New Roman The Monotype Corporation plc
Univers Linotype-Hell AG and/or its subsidiaries
All other trademarks are the property of their respective owners.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Values are subject to change. See www.lexmark.com for current values.
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products.
If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.

This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching the metal frame of the printer.
Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
Ambient temperature 15.6 to 32.2°C (60 to 90°F)
Shipping and storage temperature -40 to 43°C (-40 to 110°F)
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, Chapter I, Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 7 milliwatt gallium arsenide laser operating in the wavelength of 655-675 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
A laser notice label may be affixed to this printer as shown:

Opasnost - Nevidljivo lasersko zračenje kada su kasete uklonjene i poništena sigurnosna veza. Izbjegavati izlaganje zracima.
NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, ze zařízení je vysíláno neviditelné laserové záření. Nevystavujte se působení laserového paprsku.
FARE - Usynlig laserstråling, når patroner fjernes, og spærreanordningen er slået fra. Undgå at blive udsat for laserstrålen.
VAARA - Näkymätöntä lasersäteilyä on varottava, kun värikasetit on poistettu ja lukitus on auki. Vältä lasersäteelle altistumista.
ΚΙΝΔΥΝΟΣ - Έκλυση αόρατης ακτινοβολίας laser κατά την αφαίρεση των κασετών και την απασφάλιση της μανδάλωσης. Αποφεύγετε την έκθεση στην ακτινοβολία laser.
VESZÉLY – Nem látható lézersugárzás fordulhat elő a patronok eltávolításakor és a zárószerkezet felbontásakor. Kerülje a lézersugárnak való kitettséget. PERICOLO - Emissione di radiazioni laser invisibili durante la rimozione delle cartucce e del blocco. Evitare l´esposizione al raggio laser.
FARE – Usynlig laserstråling når kassettene tas ut og sperren er satt ut av spill. Unngå eksponering for laserstrålen.
ОПАСНО! Невидимое лазерное излучение при извлеченных картриджах и снятии блокировки. Избегайте воздействия лазерных лучей. Pozor – Nebezpečenstvo neviditeľného laserového žiarenia pri odobratých kazetách a odblokovanej poistke. Nevystavujte sa lúčom.
FARA – Osynlig laserstrålning när patroner tas ur och spärrmekanismen är upphävd. Undvik exponering för laserstrålen.
危险 - 当移除碳粉盒及互锁失效时会产生看不见的激光辐射,请避免暴露在激光光束下。
危険 - カートリッジが取り外され、内部ロックが無効になると、見えないレーザー光が放射されます。 このレーザー光に当たらないようにしてください。
Power consumption
Product power consumption
The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs. 600 W
Copy The product is generating hard‑copy output from hard‑copy original documents.
Scan The product is scanning hard‑copy documents. 65 W
Ready The product is waiting for a print job. 40 W
Sleep Mode The product is in a high‑level energy‑saving mode. 7 W
Hibernate The product is in a low‑level energy‑saving mode. 0.5 W
Off The product is plugged into an electrical outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.

This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 30 minutes
By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 120 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
This product is designed with an ultra‑low power operating mode called Hibernate mode. When operating in Hibernate Mode, all other systems and devices are powered down safely.
The Hibernate mode can be entered in any of the following methods:
Factory default Hibernate Timeout for this product in all countries or regions except for EU countries and Switzerland N/A
Factory default value for this product in EU countries or regions and Switzerland 3 days
The amount of time the printer waits after a job is printed before it enters Hibernate mode can be modified between one hour and one month.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the electrical outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
This section contains regulatory information pertaining to electromagnetic compatibility.
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232–3000
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and the ecodesign of energy- related products.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.

This section contains regulatory information pertaining to products that contain telecommunication terminal equipment such as facsimile.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachments (ACTA). On the back of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to your telephone company.
This equipment uses the RJ-11C Universal Service Order Code (USOC) jack.
A plug and jack used to connect this equipment to the premises’ wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See your setup documentation for more information.
The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact your local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (for example, 03 is a REN of 0.3). For earlier products, the REN is shown separately on the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. You will also be advised of your right to file a complaint with the FCC.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
If you experience trouble with this equipment, for repair or warranty information, contact Lexmark International, Inc. at www.lexmark.com or your Lexmark representative. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
This equipment contains no user serviceable parts. For repair and warranty information, contact Lexmark International, Inc. See the previous paragraph for contact information.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. It is recommended that the customer install an appropriate AC surge arrestor in the AC outlet to which this device is connected. An appropriate AC surge arrestor is defined as one that is suitably rated, and certified by UL (Underwriter's Laboratories), another NRTL (Nationally Recognized Testing Laboratory), or a recognized safety certification body in the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges.

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless said message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)
See your user documentation in order to program this information into your fax machine.
This product meets the applicable Industry Canada technical specifications. The Ringer Equivalence Number (REN) is an indication of the maximum number of terminals allowed to be connected to a telephone interface. The terminus of an interface may consist of any combination of devices, subject only to the requirement that the sum of the RENs of all the devices does not exceed five. The modem REN is located on the rear of the equipment on the product labeling.
Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. It is recommended that the customer install an appropriate AC surge arrestor in the AC outlet to which this device is connected. An appropriate AC surge arrestor is defined as one that is suitably rated, and certified by UL (Underwriter’s Laboratories), another NRTL (Nationally Recognized Testing Laboratory), or a recognized safety certification body in the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges.
This equipment uses CA11A telephone jacks.
Ce produit est conforme aux spécifications techniques d’Industrie Canada. Le numéro REN (ringer equivalence number : numéro d’équivalence de sonnerie) fournit une indication du nombre maximum de terminaux pouvant être connectés à l’interface téléphonique. En bout de ligne, le nombre d’appareils qui peuvent être connectés n’est pas directement limité, mais la somme des REN de ces appareils ne doit pas dépasser cinq. Le numéro REN du modem est indiqué sur l’étiquette produit située à l’arrière de l’équipement.
Les compagnies de téléphone constatent que les surtensions électriques, en particulier celles dues à la foudre, entraînent d'importants dégâts sur les terminaux privés connectés à des sources d’alimentation CA. Il s’agit-là d’un problème majeur d’échelle nationale. En conséquence, il vous est recommandé de brancher un parasurtenseur dans la prise de courant à laquelle l’équipement est connecté. Utilisez un parasurtenseur répondant à des caractéristiques nominales satisfaisantes et certifié par le laboratoire d’assureurs UL (Underwriter’s Laboratories), un autre laboratoire agréé de type NRTL (Nationally Recognized Testing Laboratory) ou un organisme de certification agréé dans votre région ou pays. Ceci prévient tout endommagement de l’équipement causé par les orages et autres surtensions électriques.
Cet équipement utilise des prises de téléphone CA11A.
This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb
The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.
Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement.
Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada.
En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.
Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur et loin des fenêtres afin de garantir une protection optimale.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc-sc.gc.ca/rpb
Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme aux spécifications techniques d'Industry Canada.
The following are special conditions for the Facsimile User Instructions. The grant of a telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.
This equipment shall not be set up to make automatic calls to the Telecom's 111 Emergency Service.
This equipment may not provide for the effective hand-over of a call to another device connected to the same line.
This equipment should not be used under any circumstances that may constitute a nuisance to other Telecom customers.

Some parameters required for compliance with Telecom's telepermit requirements are dependent on the equipment associated with this device. The associated equipment shall be set to operate within the following limits for compliance to Telecom's specifications:
This product requires a Swiss billing tone filter (Lexmark part number 80D1877) to be installed on any line which receives metering pulses in Switzerland. The filter must be used, as metering pulses are present on all analog telephone lines in Switzerland.
Cet appareil nécessite l’utilisation d’un filtre de tonalité de facturation suisse (nº de référence Lexmark : 80D1877) devant être installé sur toute ligne recevant des impulsions de comptage en Suisse. Ce filtre doit être utilisé pour toute installation car ces impulsions existent sur toutes les lignes téléphoniques suisses.
Für dieses Produkt muss ein schweizerischer Billing Tone Filter zur Zählzeichenübertragung (Lexmark Teilenummer 80D1877) für jede Leitung installiert werden, über die in der Schweiz Zeitsteuertakte übertragen werden. Die Verwendung des Filters ist obligatorisch, da in allen analogen Telefonleitungen in der Schweiz Zeitsteuertakte vorhanden sind.
Questo prodotto richiede un filtro toni Billing svizzero, (codice Lexmark 80D1877) da installare su tutte le linee che ricevono impulsi remoti in Svizzera. È necessario utilizzare il filtro poiché gli impulsi remoti sono presenti su tutte le linee analogiche in Svizzera.
Products bearing the CE mark are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, radio equipment and telecommunications terminal equipment and on the ecodesign of energy‑related products.

Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
Refer to the table at the end of the Notices section for further compliance information.
This section contains the following regulatory information pertaining to wireless products that contain transmitters, for example, but not limited to, wireless network cards or proximity card readers.
This product may contain the following modular component(s):
Lexmark Regulatory Type/Model LEX-M01-005, FCC ID: IYLLEXM01005; IC:2376A-M01005
The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, radio equipment and telecommunications terminal equipment and on the ecodesign of energy-related products.
Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.

This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
Products equipped with 2.4GHz Wireless LAN option are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment and on the ecodesign of energy-related products.
Compliance is indicated by the CE marking.
Operation is allowed in all EU and EFTA countries, but is restricted to indoor use only.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product may be used in the countries indicated in the table below.

AT BE BG CH CY CZ DE DK EE
EL ES FI FR HR HU IE IS IT
LI LT LU LV MT NL NO PL PT
Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.
Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.
Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.

Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.
Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.
Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.
Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky
príslušné ustanovenia smernice 1999/5/ES.
Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
LEXMARK LED PRINTERS, AND LEXMARK MULTIFUNCTION LASER PRINTERS
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country- specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship

If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Transfer/Transport Units, Paper Feed items, if any, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
As part of your warranty service and/or replacement, Lexmark may update the firmware in your printer to the latest version. Firmware updates may modify printer settings and cause counterfeit and/or unauthorized products, supplies, parts, materials (such as toners and inks), software, or interfaces to stop working. Authorized use of genuine Lexmark products will not be impacted.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment

—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Elliptic Curve Cryptography (ECC) Cipher Suites for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Elliptic Curve Cipher Suites with SHA-256/382 and AES Galois Counter Mode (GCM) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Suite B Profile for Transport Layer Security (TLS) implemented in the product or service.

The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Addition of the Camellia Cipher Suites to Transport Layer Security (TLS) implemented in the product or service.
The use of certain patents in this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for AES-CCM ECC Cipher Suites for TLS implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for IKE and IKEv2 Authentication Using the Eliptic Curve Digital Signature Algorithm (ECDSA) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Suite B Cryptographic Suites for IPSec implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Algorithms for Internet Key Exchange version 1 (IKEv1) implemented in the product or service.











printing from a Macintosh
computer 70 printing from Windows 70 vertical voids appear on prints 299 viewing
reports 236 viewing a fax log 110 virtual display
checking, using Embedded Web
Server 236 voice mail
setting up 94 Voice over Internet Protocol (VoIP)
fax setup 99 VoIP adapter 99 volatile memory 206
ordering 215 replacing 215 Waste toner bottle nearly full [82.xy] 269 wiping the printer hard disk 208 Wireless menu 138 wireless network
configuration information 40 wireless network setup
using the Embedded Web
Server 43 wireless setup wizard
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.