


Use only the power supply and power supply cord provided with this product or the manufacturer's authorized replacement power supply and power supply cord.
Connect the power supply cord to an electrical outlet that is near the product and easily accessible.
CAUTION—POTENTIAL INJURY: Do not twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If the power cord is misused, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of misuse. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a professional service person.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific Lexmark components. The safety features of some parts may not always be obvious. Lexmark is not responsible for the use of other replacement parts.
SAVE THESE INSTRUCTIONS.
Safety information

Finding information about the printer
Introduction

Record the following information (located on the store receipt and the back of the printer), and have it ready when you contact customer support so that they may serve you faster:
Introduction

Introduction

Bypassing security warnings during software installation
Third-party applications, including antivirus, security, and firewall programs may alert you about the printer software being installed. For your printer to work properly, allow the printer software to be installed on your computer.
Use the following instructions if you do not want to connect the printer to a computer.
1 Unpack the printer.


Setting up the printer

2 Remove all tape and packing material from all areas of the printer.

3 Raise the paper support, and then extend the paper exit tray.


4 Extend the paper guides.

5 Connect the power cord to the printer, and then to an electrical outlet that is easily accessible and near the printer.

Setting up the printer

6 Press to turn on the printer.

7 If prompted, set the language.

8 If prompted, set the country/region.

Setting up the printer

9 Open the printer, and then press down on the print cartridge carrier levers.


10 Open the color cartridge foil, and then remove the cartridge from the pack.
11 If a storage unit is included, remove the color cartridge from the storage unit.
Setting up the printer

12 Remove the tape from the color print cartridge, insert the cartridge in the right carrier, and then close the color cartridge lid.

13 If a black print cartridge is included in the box contents, open the black cartridge foil, and then remove the cartridge from the pack.
Setting up the printer

14 Remove the tape from the black print cartridge, insert the cartridge in the left cartridge carrier, and then close the cartridge carrier lid.

15 Close the printer, and then load plain paper.


Setting up the printer

16 From the printer control panel, press .

An alignment page prints.
17 Discard or recycle the alignment page.

Setting up the printer


1 Paper support Load paper.
2 Printer control panel Operate the printer.
Check wireless status:
4 PictBridge port Connect a PictBridge-enabled digital camera or a flash drive to the printer.
5 Card reader light Check card reader status. The light blinks to indicate that a memory card is being accessed.
6 Quick Connect laptop port
Connect a laptop computer to the printer using a USB cable.
7 Memory card slots Insert a memory card.
8 Paper exit tray Hold paper as it exits.
Setting up the printer
Use the To · 3 Wi-Fi indicator


10 Paper feed guard Prevent items from falling into the paper slot.

1 Scanner glass Scan and copy photos and documents.
3 Print cartridge carrier Install, replace, or remove a print cartridge.
4 Rear USB port
Connect the printer to a desktop computer using a USB cable.
5 Power supply with port Connect the printer to a power source.
6 Internal wireless print server
Connect the printer to a wireless network.
Setting up the printer
Use the To

The printer control panel contains:


3 / Switch to color mode or black-and-white mode.
4 Start a print, scan, or copy job, depending on which mode is selected.
Setting up the printer

11 Access the setup menu and change printer settings.
A number of menus are available to make it easy for you to change printer settings:
Setting up the printer
Press To

Setup menu Photo menu
Network Setup (appears only if the printer is connected to a network)
Select Computer (appears only if the printer is connected to a network)
Setting up the printer

Copy menu Scan menu PictBridge menu
To access the Copy menu, press on the printer control panel.
From here You can
Copies Specify the number of copies to print. You can choose from one to 99.
Quality Set the quality of a copy as Automatic, Draft, Normal, or Photo.
Lighter/Darker Adjust the brightness of a copy.
Resize Choose to resize the copy by a percentage or according to other options.
Original Size Specify the size of the document being copied.
Photo Reprint Make high-quality reprints of a photograph.
Collate Copy multiple pages as a set. The last page copied is printed first.
Pages per Sheet Choose how many pages to print on a sheet of paper. You can print one, two, or four pages per sheet.
Copies per Sheet Choose how many copies of an image to print on a page. You can copy one, four, nine, or 16 images per page.
Content Type Specify the type of document being copied: text and graphics, photo, or text only.
Setting up the printer

To access the Scan menu, press on the printer control panel.
From here You can
Scan to Choose the destination of the scanned image.
Select:
Quality Choose a scan quality.
Original Size Set the size of the original document.
The Photo menu automatically launches when you insert a memory card or a flash drive that contains only image files into the printer.
If the flash drive you inserted into the printer contains document files and image files, press the arrow buttons until Photo appears, and then press .
You can also access the Photo menu when you press on the printer control panel and then insert a memory device.
From here You can
Easy Photo Print photos. You can print the last photo, print all photos, print photos that fall within a date range, or print photos by selecting photo numbers. You can also set the photo size and paper size.
Print Photos Print photos using the selections in the Easy Photo menu plus:
Setting up the printer

From here You can
Proof Sheet Print and then scan a proof sheet:
Save Photos Save photos to a computer or memory device.
Select Computer (appears only in printers connected to a network)
Choose a network computer.
The PictBridge menu automatically launches when you connect a PictBridge-enabled digital camera to the printer. The menu lets you select printer settings if no settings are selected from your digital camera.
For more information on making camera selections, see the documentation that came with your camera.
From here You can
Photo Size Specify the size of the photo to be printed.
Paper Size Specify a paper size.
Paper Type Specify a paper type.
Layout Choose the layout of the photo or photos to be printed.
Quality Choose the quality of the photo or photos to be printed.
To access the Setup menu, press on the printer control panel.
From here You can
Maintenance Select:
Setting up the printer

From here You can
Device Setup Select:
Select:
Defaults Select:
After selecting an option, press to save your selection. Press until you exit Setup, or press another mode button.
You can set the default paper size, paper type, and photo print size for the documents and photos that you print.
1 From the printer control panel, press .
2 Press the arrow buttons until Defaults appears, and then press .
Paper Size appears on the display.
3 Press again.
4 Press the arrow buttons to select the default paper size for the printer, and then press .
5 Press the arrow buttons until Paper Type appears, and then press .
6 Press the arrow buttons to select the default paper type for the printer, and then press .
7 Press the arrow buttons until Photo Print Size appears, and then press .
Setting up the printer
Network Setup

8 Press the arrow buttons to select the default photo print size for the printer, and then press .
9 Press until you exit Setup, or press another mode button.
The printer has default temporary settings for the menus. The printer reverts to these default temporary settings after two minutes of inactivity or after the printer is turned off:
Photo menu The following Photo options will not time out after two minutes of inactivity or after turning off the power but will return to the default factory settings when a memory card or flash drive is removed.
1 From the printer control panel, press .
2 Press the arrow buttons until Defaults appears, and then press .
3 Press the arrow buttons until Set Defaults appears, and then press .
Use Current appears on the display.
4 Press again.
5 Press until you exit Setup, or press another mode button.
You can disable the settings timeout feature if you do not want the printer to revert to the default temporary settings after two minutes of inactivity or after turning off the printer.
1 From the printer control panel, press .
2 Press the arrow buttons until Device Setup appears, and then press .
Setting up the printer

3 Press the arrow buttons until Clear Settings Timeout appears, and then press .
4 Press the arrow buttons until Never appears, and then press .
5 Press until you exit Setup, or press another mode button.
You can customize the Power Saver timeout of the printer. The Power Saver timeout is the time it takes for the printer to switch to Power Saver mode when the printer is left idle. Change the Power Saver timeout to avoid interruptions when doing multiple jobs on your printer.
1 From the printer control panel, press .
2 Press the arrow buttons until Device Setup appears, and then press .
3 Press the arrow buttons until Power Saver appears, and then press .
4 Press the arrow buttons to select a Power Saver timeout, and then press .
5 Press until you exit Setup, or press another mode button.
1 Close all open software programs.
2 Insert the printer software CD.
3 From the main installation screen, click Install.
4 Follow the instructions on the screens.
1 Close all open software applications.
2 Insert the printer software CD.
3 From the Finder desktop, double-click the printer CD icon that automatically appears.
4 Double-click the Install icon.
5 Follow the instructions on the screens.
1 Go to the Lexmark Web site at www.lexmark.com.
2 From the home page, navigate through the menu selection, and then click Drivers & Downloads.
Setting up the printer

3 Choose the printer and the printer driver for your operating system.
4 Follow the instructions on the screens to download the driver and install the printer software.
The XML Paper Specification (XPS) driver is an optional printer driver designed to make use of the advanced XPS color and graphics features that are available only for Windows Vista users. To use XPS features, you must install the XPS driver as an additional driver after you install the regular printer software.
To install the Microsoft QFE Patch and extract the driver:
1 Insert the installation software CD, and then click Cancel when the Setup Wizard appears.
Computer.
3 Double-click the CD-ROM drive icon, and then double-click Drivers.
4 Double-click xps, and then double-click setupxps file.
XPS driver files are copied to your computer, and any required Microsoft XPS files are launched. Follow the instructions on the screen to finish installing the patch.
To install the XPS driver:
Control Panel.
2 Under Hardware and Sound, click Printer, and then click Add a Printer.
3 From the Add Printer dialog, click Add a local printer.
4 From the “Use an existing port” drop-down menu, select Virtual printer port for USB, and then click Next.
5 Click Have disk.
The Install From Disk dialog appears.
6 Click Browse, and then navigate to the XPS driver files on your computer: a Click Computer, and then double-click (C:). b Double-click the folder that ends in your printer model number, and then double-click Drivers.
c Double-click xps, and then click Open. d From the Install From Disk dialog, click OK.
7 Click Next on the two additional dialogs that appear.
For more information on the XPS driver, see the XPS readme file on the installation software CD. The file is located in the xps folder with the setupxps batch file (D:\Drivers\xps\readme).
Setting up the printer
2 Click · 1 Click

When you set up the printer using the printer software CD, all the necessary software was installed. You may have chosen to install some additional programs. The following table provides an overview of various software programs and what they can help you do.
Lexmark Fast Pics Manage, edit, transfer, and print photos and documents.
Lexmark Tools for Office Access your favorite settings in Microsoft Office 2007.
Abbyy Sprint OCR Scan a document and produce text that you can edit with a word-processing program.
Setting up the printer
Use the To

Printing Preferences When you select File Print with a document open and then click Properties, a Printing Preferences dialog appears. The dialog lets you select options for the print job such as the following:
If you have not installed these additional programs during initial installation, reinsert the installation software CD, run the installation software, and then select Install Additional Software from the Software Already Installed screen.
Print dialog Adjust the print settings and schedule print jobs.
Applications are also installed with the printer software during installation. These applications are saved in the printer folder that appears on the Finder desktop after installation.
1 From the Finder desktop, double-click the printer folder.
2 Double-click the icon of the application that you want to use.
Setting up the printer
Use the To · Use the To · Use the To

Lexmark Wireless Setup Assistant Set up the printer on a wireless network.
Switching between the rear USB port and the Quick Connect laptop port (selected models only)
If the printer is connected to a desktop computer through the rear USB port and you decide to connect a laptop computer to the printer through the Quick Connect laptop port, then the Quick Connect laptop port connection overrides the rear USB port connection. The active print jobs on the desktop computer may be canceled. Pause or cancel active jobs on the desktop computer before switching between ports.
1 Pause or cancel active jobs on the desktop computer.
2 Connect a USB cable to the laptop computer and then to the Quick Connect laptop port on the front of the printer.
3 If you have not yet installed the printer software on the laptop, then install it.
a Insert the installation software CD. b Wait for the Welcome screen to appear.
If the Welcome screen does not appear after a minute, do one of the following:
. 2 In the Start Search box, type D:\setup.exe, where D is the letter of your CD or DVD drive.
1 Click Start. 2 Click Run. 3 Type D:\setup.exe, where D is the letter of your CD or DVD drive.
c Follow the instructions on the computer screen.
Setting up the printer
Use the To · 1 Click

a Insert the installation software CD. b Wait for the Welcome screen to appear.
Setting up the printer


Wireless network compatibility
Your printer contains an IEEE 802.11g wireless print server. Your printer is compatible with IEEE 802.11 b/g/n routers that are Wi-Fi certified. If you are having issues with an n router, verify with your router manufacturer that the current mode setting is compatible with g devices, as this setting varies depending on the router brand/model.
Information you will need to set up the printer on a wireless network
To set up the printer for wireless printing, you need to know:
If your wireless access point (wireless router) is using Wired Equivalent Privacy (WEP) security, the WEP key should be:
or • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, punctuation, and symbols found on a keyboard.
If your wireless access point (wireless router) is using Wi-Fi Protected Access (WPA) security, the WPA passphrase should be:
or • Exactly 64 hexadecimal characters. Hexadecimal characters are A-F, a-f, and 0-9.
If your wireless network is not using security, then you will not have a security key. Using a wireless network with no security is not recommended because it can allow intruders to use your network resources without your consent.

Note: If you do not know the SSID of the network that your computer is connected to, launch the wireless utility of the computer network adapter and look for the network name. If you cannot find the SSID or the security information for your network, see the documentation that came with the wireless access point (wireless router), or contact your system support person.
Installing the printer on a wireless network (selected models only)

Before you install the printer on a wireless network, make sure that:
1 Insert the installation software CD.
2 Wait a minute for the Welcome screen to appear.
If the Welcome screen does not appear after a minute, do one of the following:
. b In the Start Search box, type D:\setup.exe, where D is the letter of your CD or DVD drive.
a Click Start. b Click Run.
c Type D:\setup.exe, where D is the letter of your CD or DVD drive.
3 Follow the instructions on the Welcome screen to set up the printer.
1 Insert the installation software CD.
2 Wait a minute for the Welcome screen to appear.
3 Double-click Install.
4 Follow the instructions on the Welcome screen to set up the printer.
The following instructions apply to customers using a LiveBox, AliceBox, N9UF Box, FreeBox, or Club Internet.
1 Make sure your box is wireless-enabled and activated to work on a wireless network. For more information about configuring the box to work wirelessly, see the documentation that came with your box.
2 Before installing the printer, make sure your box is turned on and that your computer is on and connected to your wireless network.
3 Set up your printer using the setup instructions provided.
Installing the printer on a wireless network (selected models only)
a Click

4 If there is an associate/registration button on the back of your box, press it when you are prompted to choose a network.
5 Return to the computer screen, and choose the network you want to connect to. If you want to use the network shown, choose Connect to <network name>, and then click Continue.
If you do not want to use the network shown:
a Choose Connect to another network, and then click Continue. b Choose the network you want to use from the list of available networks, and then click Continue.
6 Enter the Network key, and then click Continue.
7 Follow the instructions on your screen to complete installation.
The printer will be assigned an IP address automatically through DHCP on most wireless networks.
During wireless setup, you will be asked to manually assign an IP address to the printer in the following situations:
For more information, contact your system support person.
The Wi-Fi indicator light helps you determine the network status of the printer.
The following describes what the colors of the Wi-Fi indicator light mean.
The light should be in this state:
– When the printer is turned off – When the printer is in power saver mode – When the printer does not have an internal print server installed and you want to connect the printer to the
computer using a USB cable • Orange may indicate that the printer is being configured for use on the wireless network, the internal print server is not configured in infrastructure mode, or the internal print server is waiting to be configured for ad hoc mode.
The light should be in this state:
– When you want to use the printer without a computer – When you want to set up the printer on your wireless network – When the printer is set up for an ad hoc network and is broadcasting its wireless network name (SSID)
Installing the printer on a wireless network (selected models only)

point (wireless router) may be turned off or not working properly. – The printer is trying to establish communication with the wireless access point (wireless router).
This is true if you have already configured the printer for use on your wireless network. When the printer has been configured, any time you turn the printer off and then turn it back on, the internal print server in the printer will try to connect to your wireless access point (wireless router). – The wireless settings of the printer may no longer be valid. • Green indicates that the printer is connected to a wireless network.
The light should be in this state when you want to start using the printer that is already set up on your wireless network. • Blinking green indicates that the printer internal print server is being updated.
To change wireless settings on the printer, such as the configured network, the security key, or other settings:
1 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start.
2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Click Tools Lexmark Wireless Setup Utility.
4 Follow the prompts on the computer screen to reinstall the software, and then make the changes that you want.
1 From the Finder desktop, double-click the printer folder.
2 Double-click Lexmark Wireless Setup Assistant.
3 Follow the instructions on the computer screen.
Installing the printer on a wireless network (selected models only)

The Network Setup menu is available only if your printer model has an internal wireless print server, and if the printer is connected to a network. Use this menu to view the wireless settings of the printer, print a network setup page, and reset the internal wireless print server.
1 From the printer control panel, press .
2 Press the arrow buttons until Network Setup appears, and then press .
From here You can
Print Setup Page Print a network setup page.
Wireless Information View the network name of the current active network and the signal strength of the connection.
TCP/IP View network settings.
File Print Choose whether to select a network computer automatically or manually for File Print jobs.
Reset Network Adapter Defaults Reset the internal wireless print server to factory default settings.
From here You can
Network Name View the current Service Set Identifier (SSID).
Wireless Signal Quality View the wireless signal strength.
From here You can
View IP Address View the IP address currently assigned to the printer.
View IP Netmask View the subnet mask currently configured for the printer.
View IP Gateway View the currently configured gateway IP address for the network.
Once the printer is configured, it can be accessed wirelessly by any other computer on the network. However, you will need to install the printer driver on every computer that will access it. You do not need to configure the printer again, although you will need to run the setup software on each computer to install the driver.
Installing the printer on a wireless network (selected models only)

1 Insert the installation software CD.
2 Wait for the Welcome screen to appear.
If the Welcome screen does not appear after a minute, do one of the following:
. b In the Start Search box, type D:\setup.exe, where D is the letter of your CD or DVD drive.
a Click Start. b Click Run.
c Type D:\setup.exe, where D is the letter of your CD or DVD drive.
3 Follow the on-screen instructions for installing a configured printer on a new computer.
1 Insert the installation software CD.
2 Wait for the Welcome screen to appear.
3 Double-click Install.
4 Follow the on-screen instructions for installing a configured printer on a new computer.
The recommended way to set up your wireless network is to use a wireless access point (wireless router). A network set up this way is called an infrastructure network. If you have an infrastructure network in your home, you should configure your printer for use on that network.
If you do not have a wireless access point or would like to set up a standalone network between your printer and a computer with a wireless network adapter, then you can set up an ad hoc network.
2 Click Control Panel.
3 Click Network and Internet.
4 Under Network and Sharing Center, click Connect to a Network.
Installing the printer on a wireless network (selected models only)
a Click · 1 Click

5 In the Connect to a Network dialog, click Set up a wireless ad-hoc (computer-to-computer) network, and then click Next.
6 Follow the instructions in the “Set up a wireless ad hoc network” wizard. As part of the setup: a Create a network name or SSID for the network between the computer and your printer. b Write the name of your network in the space provided so you can refer to it when running the wireless setup.
Make sure you copy the exact spelling and capitalization.
SSID (name of your wireless network)
c Go to the Security Type drop-down list, choose WEP, and then create a security key (or password).
WEP keys must be:
setup. Make sure you copy the exact spelling and capitalization.
Security key (if network is secure)
Windows Vista will enable the ad hoc network for you. It will appear in the “Connect to a network” dialog under “Available networks,” indicating that the computer is configured for the ad hoc network.
7 Close the Control Panel and any remaining windows.
8 If this is the first time you will be setting up the printer for use on a wireless network, insert the installation software CD, and then follow the instructions on the Welcome screen.
Otherwise:
. b Click All Programs.
c Select the printer program folder, and then click Tools Lexmark Wireless Setup Utility.
9 When the available networks are displayed, provide the network name and the security information you created. The installer will configure the printer for use with your computer.
10 Store a copy of your network name and security information in a safe place for future reference.
1 Click Start.
2 Click Control Panel.
3 Click Network and Internet Connections.
4 Click Network Connections.
5 Right-click the icon for your wireless network connection.
Installing the printer on a wireless network (selected models only)
a Click

6 Click Enable, if it appears in the pop-up menu.
7 Right-click the Wireless Network Connection icon.
8 Click Properties.
9 Click the Wireless Networks tab.
10 Select the Use Windows to configure my wireless network settings check box.
11 Under Preferred Networks, delete any existing networks. a Select the network to be removed. b Click Remove to delete the network from the list.
12 Click Add to create an ad hoc network.
13 In the Network Name (SSID) box, type the name you want to give your wireless network.
14 Write down the network name you chose so you can refer to it when running the wireless setup. Make sure you copy the exact spelling and capitalization.
SSID (name of your wireless network)
15 If Network Authentication appears in the list, then select Open.
16 In the “Data encryption” list, select WEP.
17 If necessary, clear the “The key is provided for me automatically” check box.
18 In the Network Key box, type in a security key.
19 Write down the security key you chose so you can refer to it when running the wireless utility. Make sure you copy the exact spelling and capitalization.
Security key (if network is secure)
20 In the “Confirm network key” box, type the same security key.
21 Select This is a computer-to-computer (ad hoc) network; wireless access points are not used..
22 Click OK twice to close the two open windows.
Installing the printer on a wireless network (selected models only)

23 It may take a few minutes for your computer to recognize the new settings. To check on the status of your network: a Right-click the Wireless Network Connections icon. b Select View Available Wireless Networks.
24 If this is the first time you will be setting up the printer for use on a wireless network, insert the installation software CD, and then follow the instructions on the Welcome screen.
Otherwise:
a Click Start. b Click All Programs or Programs.
c Select the printer program folder from the list, and then click Tools Lexmark Wireless Setup Utility.
25 When the available networks are displayed, provide the network name and the security information you created in steps 11-16. The utility will configure the printer for use with your computer.
26 Store a copy of your network name and security information in a safe place for future reference.
1 Make sure the computer is on.
2 Create a network name.
System Preferences. b Click Network.
a From the Finder desktop, click
c Click AirPort. d From the Network Name pop-up menu, click Create Network. e Create a name for your ad hoc network, and then click OK.
a From the Finder desktop, click Go Applications. b From the Applications folder, double-click Internet Connect.
c From the toolbar, click AirPort. d From the Network pop-up menu, click Create Network. e Create a name for your ad hoc network, and then click OK.
3 Write down the network name you chose so you can refer to it when running the wireless utility. Make sure you copy the exact spelling and capitalization.
SSID (name of your wireless network)
Installing the printer on a wireless network (selected models only)

4 If this is the first time you will be setting up the printer for use on a wireless network, insert the installation software CD, double-click the installer icon for your printer on the Finder desktop, and then follow the instructions on the Welcome screen.
Otherwise, from the Finder desktop, double-click the printer folder, and then double-click Lexmark Wireless Setup Assistant.
5 When prompted, provide the network name and/or the security information you created.
The utility will configure the printer for use with your computer.
6 Store a copy of your network name and security information in a safe place for future reference.
1 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start.
2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Click Lexmark Wireless Setup Utility.
4 Follow the instructions on the Welcome screen.
1 From the Finder desktop, double-click the printer folder.
2 Double-click Lexmark Wireless Setup Assistant.
3 Follow the instructions on the Welcome screen.
A network is a collection of devices such as computers, printers, Ethernet hubs, wireless access points, and routers connected together for communication through cables or through a wireless connection. A network can be wired, wireless, or designed to have both wired and wireless devices.
Devices on a wired network use cables to communicate with each other.
Devices on a wireless network use radio waves instead of cables to communicate with each other. For a device to be able to communicate wirelessly, it must have a wireless print server attached or installed that lets it receive and transmit radio waves.
For desktop computers, laptops, and printers to communicate with each other over a network, they must be connected by cables and/or have wireless network adapters built in or installed in them.
Installing the printer on a wireless network (selected models only)

There are different ways a network can be set up. Five common examples appear below.

Four common wireless networks are:
Installing the printer on a wireless network (selected models only)




Installing the printer on a wireless network (selected models only)

When setting up the printer on your wireless network, the printer will need to temporarily connect to a computer using the installation cable. This temporary connection is used to set up the wireless settings of the printer.
The installation cable connects to a rectangular USB port on the installing computer and the square USB port on the printer.
The installation cable attaches to a USB port on the computer and to the square connector on the back of the printer. This connection allows you to configure the printer for a networked or locally attached installation.
1 Attach the large, rectangular connector to any USB port on your computer. USB ports may be on the front or the back of the computer, and may be horizontal or vertical.

Installing the printer on a wireless network (selected models only)

2 Attach the small, square connector to the printer.
3 Continue following the on-screen instructions.
Wireless networks can operate in one of two modes: infrastructure or ad hoc.
In infrastructure mode, all devices on a wireless network communicate with each other through a wireless router. Devices on the wireless network must have valid IP addresses for the current network and share the same SSID and channel as the wireless router (wireless access point).
In ad hoc mode, a computer with a wireless network adapter communicates directly with a printer equipped with a wireless print server. The computer must have a valid IP address for the current network and be set to ad hoc mode. The wireless print server must be configured to use the same SSID and channel that the computer is using.
The following table compares the characteristics and requirements of the two types of wireless networks.
Communication Through wireless access point (wireless router)
Security More security options
Range Determined by range and number of wireless access points (wireless routers)
Restricted to range of individual devices on network
Speed Usually faster Usually slower
Requirements for all devices
Unique IP address for each device Yes Yes
Mode set to Infrastructure mode Ad hoc mode
Same SSID Yes, including the wireless access point (wireless router)
Installing the printer on a wireless network (selected models only)

Same channel Yes, including the wireless access point (wireless router)
Lexmark recommends setting up a network in infrastructure mode using the installation CD that came with the printer.
Infrastructure mode is the recommended setup method because it has:
Wireless devices have built-in antennas that transmit and receive radio signals. The signal strength listed on the printer network setup page indicates how strongly a transmitted signal is being received. Many factors can affect the signal strength. One factor is interference from other wireless devices or other devices such as microwave ovens. Another factor is distance. The farther two wireless devices are from each other, the more likely it is that the communication signal will be weaker.
The strength of the signal received by your computer can also affect the connectivity of the printer with the network during configuration. When you installed the wireless adapter in your computer, the adapter software probably placed an icon in your system tray. Try double-clicking this icon, and it will tell you how strongly the computer is receiving the wireless signal from the network.
To improve signal quality, remove sources of interference and/or move wireless devices closer to the wireless access point (wireless router).
A common reason wireless printers fail to communicate over a network is poor wireless signal quality. If the signal is too weak, too distorted, or blocked by an object, it cannot carry information between the access point and the printer. To determine if the printer is receiving a strong signal from the access point, print a network setup page. The Quality field indicates the relative strength of the wireless signal the printer is receiving. Drops in signal strength can be intermittent, however, and although the signal quality appears high, it may drop during certain conditions.
If you think signal strength is a problem between your access point and the printer, try one or more of the following:
MOVE THE PRINTER CLOSER TO THE WIRELESS ACCESS POINT/WIRELESS ROUTER
If the printer is too far away from the access point, it will not be able to communicate with other devices on the network. For most indoor wireless networks, the maximum distance between the access point and the printer is approximately 100 feet (30 meters). This distance could be longer or shorter, depending upon the layout of the network and the limitations of the access point.
Installing the printer on a wireless network (selected models only)
Infrastructure Ad hoc · Yes

The wireless signal from your access point will pass through most objects. Most walls, floors, furniture and other objects will not block the wireless signal. However, there are materials that are too dense for the signal to pass through. Objects containing metal and concrete can block the signal, including:
Arrange your printer and access point so that the signal is not blocked by any of these objects.
Other types of radio frequencies can cause problems with the wireless signal on your network. These sources of interference can cause printing issues that seem to come and go. Some common sources of interference are:
Turn off these potential sources of interference where possible. Avoid using microwaves and cordless phones when printing over your wireless network.
If another wireless network is operating in the vicinity, change the wireless channel on the access point.
Do not place your access point on a printer. Printers can also interfere with the wireless signal.
Even when the wireless signal is able to pass through an object, it is slightly weakened. If it passes through too many objects, it can be significantly weakened. All objects absorb part of the wireless signal when it passes through them, but certain types of objects absorb enough to cause communications problems. To avoid signal absorption, avoid placing the following items between your access point and your printer:
Place your access point as high in the room as possible to avoid signal absorption.
Installing the printer on a wireless network (selected models only)

A Service Set Identifier (SSID) is the name that identifies a wireless network. All devices on the network must know the SSID of the wireless network or they will not be able to communicate with each other. Usually, the wireless network broadcasts the SSID to allow wireless devices in the area to connect to it. Sometimes, the SSID is not broadcast for security reasons.
An SSID can contain up to 32 alphanumeric characters.
How do I find out what type of security my network is using?
You must know the security key and security mode to properly set up the printer for use on the wireless network. To obtain this information, see the documentation that came with your wireless access point (wireless router), see the Web page associated with the wireless access point (wireless router), or consult your system support person.
Can I use my printer on a USB and a wireless connection at the same time?
The printer can be configured in the following ways:
If you want to use the printer as both a wireless and locally attached printer at the same time, you will need to run the setup software again and select the additional connection type.
A Media Access Control (MAC) address is a 48-bit identifier associated with the hardware of network equipment. The MAC address may also be called the physical address because it is connected to the hardware of a device instead of its software. The MAC address is displayed as a hexadecimal number in this format: 01-23-45-67-89-AB.
Every device capable of communicating on a network has a MAC address. Network printers, computers, and routers, whether Ethernet or wireless, all have MAC addresses.
While it is possible to change the MAC address of a network device, it is not common practice to do so. For this reason, MAC addresses are considered permanent. IP addresses are easily changed, so MAC addresses are a more reliable method of identifying a specific device on a network.
Routers with security capabilities may allow filtering of MAC addresses on networks. This allows a managed list of devices to access the network, identified by their MAC addresses. MAC address filtering can help prevent access on the network from unwanted devices, such as from intruders on a wireless network. MAC address filtering can also prevent legitimate access if you forget to add a new device to the router's list of allowed addresses. If your network uses MAC address filtering, be sure to add the MAC address of the printer to the list of allowed devices.
Installing the printer on a wireless network (selected models only)

Most network equipment has a unique hardware identification number to distinguish it from other devices on the network. This is called the Media Access Control (MAC) address.
The MAC address is a series of letters and numbers located on the back of your printer.

Note: A list of MAC addresses can be set on an access point (router) so that only devices with matching MAC addresses are allowed to operate on the network. This is called MAC filtering. If MAC filtering is enabled in your access point (router) and you want to add a printer to your network, the MAC address of the printer must be included in the MAC filter list.
An IP address is a unique number used by devices (such as a wireless printer, computer, or wireless access point) on an IP network to locate and communicate with each other. Devices on an IP network can communicate with each other only if they have unique and valid IP addresses. A unique IP address means no two devices on the same network have the same IP address.
An IP address is a group of four numbers separated by periods. An example of an IP address is 192.168.100.110.
Networks are able to function because computers, printers, and other devices are able to send data to each other, either through cables or by using wireless signals. This transfer of data is made possible by sets of data transmission rules called protocols. A protocol can be thought of as a language, and like a language, it has rules allowing participants to communicate with each other.
Different types of networks use different protocols, but Transmission Control Protocol/Internet Protocol (TCP/IP) is the most popular. TCP/IP is used to send data over the Internet as well as over most corporate and home networks.
Because computers do not understand words and instead rely upon numbers for communication, TCP/IP requires that every device on a network using TCP/IP to communicate must have an IP address. IP addresses are essentially unique computer names in a numeric format, used to transfer data around a network. IP addresses allow TCP/IP to confirm requests for and receipt of data by various devices on the network.
Installing the printer on a wireless network (selected models only)

1 Do one of the following:
. b Click All Programs Accessories.
c Click Command Prompt.
a Click Start. b Click All Programs or Programs Accessories Command Prompt.
2 Type ipconfig.
3 Press Enter.
The IP address appears as four sets of numbers separated by periods, such as 192.168.0.100.
System Preferences.
2 Click Network.
a Click AirPort. b Click Advanced.
c Click TCP/IP. The IP address appears as four sets of numbers separated by periods, such as 192.168.0.100.
a From the Show pop-up menu, select AirPort. b Click TCP/IP.
The IP address appears as four sets of numbers separated by periods, such as 192.168.0.100.
An IP address may be assigned automatically by the network using DHCP. Once the printer is set up on a computer, the computer sends all print jobs across the network to the printer using this address.
If the IP address is not automatically assigned, you will be asked during wireless setup to manually enter an address and other network information after selecting your printer from the available list.
Installing the printer on a wireless network (selected models only)
a Click · 1 Click

A wireless access point (wireless router) can be configured with as many as four WEP keys. Only one key is used on the network at a time, however. The keys are numbered, and the number of a key is referred to as its key index. All devices on the wireless network must be configured to use the same key index when multiple WEP keys are configured on the wireless access point (wireless router).
The printer is designed to use the first key. Make sure you have configured all of the wireless devices on your network to use the first WEP key where you have the option of selecting a key. Make sure the wireless access point (wireless router) is also configured to use the first key. The first key will usually have an index of 0, though it may be 1 on some devices.
Installing the printer on a wireless network (selected models only)

Loading paper
2 Before loading paper the first time, slide the paper guides out toward the edges of the paper support.
3 Load the paper vertically in the center of the paper support, and adjust the paper guides to rest against the edges of the paper.
You can load up to 100 sheets (depending on the thickness).
Make sure:
You can load up to 25 sheets.
Make sure:
Loading paper

You can load up to 10 envelopes.
Make sure:
You can load up to 25 sheets.
Make sure:
You can load up to 10 transparencies.
Loading paper

Make sure:
You can load up to 10 transfers.
Make sure:
You can load up to 25 cards.
Make sure:
You can load up to 100 sheets (depending on the thickness).
Make sure:
Loading paper

Width:
– 76.2–215.9 mm – 3.0–8.5 inches
Length:
You can load up to 20 sheets.

Make sure:
Loading paper

You can scan and then print photos, text documents, magazine articles, newspapers, and other publications. You can scan a document for faxing.
1 Open the top cover.

2 Place the original document or item facedown on the scanner glass in the lower right corner.

Loading paper

3 Close the top cover to avoid dark edges on the scanned image.

The printer is equipped with an automatic paper type sensing device. The Paper Type Sensor automatically detects the type of paper that has been loaded into the printer and adjusts the settings for you. For example, if you want to print a photo, load photo paper into the printer. The printer detects the type of paper and automatically adjusts the settings to give you optimum photo-printing results.
Loading paper

For instructions on additional printing tasks, see the Help associated with the printer software.
1 Load the paper.
2 Do one of the following to print:
a With a document open in a Windows program , click File Print. b Click Properties, Preferences, Options, or Setup.
c Select the print quality, the number of copies to print, the type of paper to be used, and how the pages should print. d Click OK to close any printer software dialogs. e Click OK or Print.
a With a document open in a Macintosh application, click File Print. b From the Printer pop-up menu, choose the printer.
c From the print options pop-up menu, choose the print quality, the number of copies to print, the type of paper to be used, and how the pages should print. d Click Print.
If you chose to install the Lexmark Toolbar software for your Web browser, then you can use it to create a printer-friendly version of any Web page.
Printing


1 Load paper.
2 Open a Web page using a supported browser.
3 Select a print option to print the page.
You can also adjust settings or preview the page before printing.
1 With a document open, click File Print.
2 Click Properties, Preferences, Options, or Setup.
3 From the Copies section of the Print Setup tab, enter the number of copies that you want to print.
4 Click OK to close any printer software dialogs.
5 Click OK or Print.
1 With a document open, click File Print.
2 From the Printer pop-up menu, choose the printer.
3 In the Copies field, enter the number of copies that you want to print.
4 Click Print.
If you print multiple copies of a document, you can choose to print each copy as a set (collated) or to print the copies as groups of pages (not collated).
1 With a document open, click File Print.
2 Click Properties, Preferences, Options, or Setup.
3 From the Copies section of the Print Setup tab, enter the number of copies that you want to print, and then select Collate Copies.
Collated Not collated · Printing

4 Click OK to close any printer software dialogs.
5 Click OK or Print.
1 With a document open, click File Print.
2 In the Copies field, enter the number of copies that you want to print, and then select Collated.
3 Click Print.
1 With a document open, click File Print.
2 Click Properties, Preferences, Options, or Setup.
3 From the Copies section of the Print Setup tab, select Print Last Page First.
4 Click OK to close any printer software dialogs.
5 Click OK or Print.
1 With a document open, click File Print.
2 From the Printer pop-up menu, choose the printer.
3 Do one of the following:
a From the print options pop-up menu, choose Paper Handling. b From the Page Order menu, select Reverse.
a From the print options pop-up menu, choose Paper Handling. b Select Reverse page order.
4 Click Print.
Printing

1 With a document open, click File Print.
2 Click Properties, Preferences, Options, or Setup.
3 From the Advanced tab, select N-Up under the Layout drop-down menu.
4 Select the number of page images to print on each page.
If you want each page image to be surrounded by a border, then select Print Page Borders.
5 Click OK to close any printer software dialogs.
6 Click OK or Print.
1 With a document open, click File Print.
3 Click Print.
To enable the File print function:
1 Insert a memory card or flash drive.
The following file types are recognized:
Printing

When the printer detects the memory device, the message Memory Card Detected or Storage Device Detected appears on the printer control panel display.
2 If only document files are stored on the memory device, then the printer automatically switches to File Print mode.
If document files and image files are stored on the memory device, then press to select Documents.
3 Do one of the following:
a Press the arrow buttons to select the file name of the document that you want to print or the folder where
the document is saved in the memory device. b Press , and then press to start printing the document.
a Wait for the printer to connect to the network computer or to finish searching the network for available
computers.
If Select Computer appears, press the arrow buttons to select a network computer, and then press .
the document is saved in the memory device. c Press , and then press to start printing the document.
You can also use the programs that are installed with the printer software to print specialty documents. For more information, see the Help associated with these programs.
Printing

1 Load the envelopes in the printer.
2 Do one of the following:
a With a document open, click File Print. b Click Properties, Preferences, Options, or Setup.
c From the Media Type list of the Print Setup tab, select Plain. d From the Paper Size list, select the envelope size.
f Click OK to close any printer software dialogs. g Click OK or Print.
a Customize the settings as needed in the Page Setup dialog.
1 With a document open, click File Page Setup. 2 From the “Format for” pop-up menu, choose the envelope size. If no size matches the size of the envelope, then set a custom size. 3 Select an orientation. 4 Click OK. b Customize the settings as needed in the Print dialog.
1 With a document open, click File Print. 2 From the Printer pop-up menu, choose the printer that you want to use. 3 Click Print.
Printing

1 Load the label sheets in the printer.
2 Do one of the following:
a With a document open, click File Print. b Click Properties, Preferences, Options, or Setup.
c From the Paper Size drop-down menu of the Print Setup tab, choose a paper size that matches the size of the label sheet. If no paper size matches the label sheet size, then set a custom size. If necessary, choose the appropriate type of media from the Media Type drop-down menu. d Click OK to close any printer software dialogs. e Click OK or Print.
a Customize the settings as needed in the Page Setup dialog.
1 With a document open, choose File Page Setup. 2 From the “Format for” pop-up menu, choose the printer that you want to use. 3 From the Paper Size pop-up menu, choose a paper size that matches the size of the label sheet. If no paper size matches the label sheet size, then create a custom size. b Customize the settings as needed in the Print dialog.
1 With a document open, click File Print. 2 From the Printer pop-up menu, choose the printer that you want to use. 3 From the print options pop-up menu, choose Quality & Media. 4 From the Paper type pop-up menu, choose a paper type. 5 From the Print Quality menu, choose a print quality other than Quick Print.
Printing

Before beginning these instructions, load the custom-size paper in the printer. For more information, see the “Loading Paper” chapter.
1 With a document open, click File Print.
2 Click Properties, Preferences, Options, or Setup.
The Print Setup tab appears.
3 In the Paper Options section, from the “Paper size” list, select Custom Size.
The Define Custom Paper Size dialog appears.
4 Select the measurement units to use (inches or millimeters).
5 Click OK to close any printer software dialogs that are open.
6 Print the document.
1 With a document open, click File Page Setup.
2 From the Paper size pop-up menu, choose Manage Custom Sizes.
3 Create a custom size. a Click +. b In the Page Size menu, type the Width and Height of the paper.
c From the Printer Margins pop-up menu, choose the printer that you want to use. The margins are set by the printer. If you want to set the margins, choose User defined, and then type the margins in the Printer Margins area. d From the custom sizes list on the left of the dialog, double-click Untitled, and then type a name for the custom
paper size you set. e Click OK.
4 Open the Paper size pop-up menu again, and then choose the name of the custom paper size you added in Step 3d.
5 Click Print.
1 With a document open, click File Print.
2 Click Properties, Preferences, Options, or Setup.
3 Make adjustments to the settings.
4 Click Profiles, and then click Save your current settings.
Printing

5 Select an empty location for your setting, and then assign a name.
6 Click Save.
7 Close all open software dialogs.
The Presets pop-up menu lets you save the print settings you use often. When print settings are saved into a Preset, there is no need to adjust the print settings for every print job.
1 With a document open, click File Print.
2 From the print options pop-up menu, choose and adjust the settings.
3 From the Presets pop-up menu, choose Save As.
The Save Preset dialog appears.
4 Type a name for the Preset.
5 Click OK.
1 Do one of the following:
. b Click Control Panel.
c Under Hardware and Sound, click Printer.
a Click Start. b Click Printers and Faxes.
a Click · Printing

a Click Start. b Click Settings Printers.
2 Right-click the printer, and then select Pause Printing.
1 Double-click the printer icon in the taskbar.
2 Right-click the document name, and then select Pause.
1 While the document is printing, click the printer icon in the Dock.
The print queue dialog appears.
1 Do one of the following:
. b Click Control Panel.
c Under Hardware and Sound, click Printer.
a Click Start. b Click Printers and Faxes.
a Click Start. b Click Settings Printers.
2 Right-click the printer name, and then select Open.
a Click · Printing

1 Double-click the printer icon in the taskbar.
2 Right-click the document name, and then select Resume.
1 From the menu bar, click
System Preferences Print & Fax.
2 Click Open Print Queue.
The print queue dialog appears.
1 From the menu bar, click Go Utilities Print Center or Printer Setup Utility.
The Printer List dialog appears.
2 Double-click the printer.
The print queue dialog appears.
Press .
The printing status window automatically opens at the bottom-right part of your screen when you send a print job. Click Cancel Printing to cancel the print job.
1 Do one of the following:
. b Click Control Panel.
c Under Hardware and Sound, click Printer.
a Click Start. b Click Printers and Faxes.
a Click · Printing

a Click Start. b Click Settings Printers.
2 Right-click the printer name, and then select Open.
1 Double-click the printer icon in the taskbar.
1 While the document is printing, click the printer icon in the Dock.
2 From the print queue dialog, choose the job that you want to cancel, and then click Delete.
Printing

You can also use the programs that are installed with the printer software to customize and print photos. For more information, see the Help associated with these programs.


Working with photos

2 Wait for the light located near the top memory card slot on the printer to come on. The light blinks to indicate the memory card is being read or is transmitting data.

When the printer detects the memory card, the message Memory Card Detected appears on the printer control panel display.
If the printer does not read the memory card, then remove and reinsert it.
1 Insert the flash drive into the PictBridge port on the front of the printer.

2 Wait for the printer to recognize that a flash drive is installed. When the flash drive is recognized, the message Storage Device Detected appears.
If the printer does not read the flash drive, remove and reinsert it.
Working with photos



1 Insert a memory card, flash drive, or digital camera set to mass storage mode.
2 From the printer control panel, press .
3 Press the arrow buttons until Save Photos appears, and then press .
4 Do one of the following:
a Press . b Press . c On the computer screen, select an option to save photos to the computer. d Follow the instructions on the computer screen.
a Press the arrow buttons until Network appears, and then press .
b If prompted, press the arrow buttons to select the network computer where you want to save the photos,
and then press .
Working with photos

c On the computer screen, select an option to save photos to the computer. d Follow the instructions on the computer screen.
. – In Windows XP and earlier, click Start. 2 Click All Programs or Programs, and then select the printer program folder from the list. 3 Click Lexmark Productivity Studio. 4 From the Photo Printing section of the main screen, click Download to library. 5 Browse to the location of the memory device, and then click Transfer. 6 Select the network printer. 7 Insert the memory device into the network printer. 8 Follow the instructions on the computer screen.
If the printer is connected to a computer through a network, then you can transfer photos from a memory card or flash drive to the computer using the Lexmark Network Card Reader. The printer may require that you select a computer (and a PIN, if required by that computer).
1 Insert a memory card, flash drive or a digital camera set to mass storage mode.
2 From the Finder desktop, double-click the printer folder.
3 Double-click the Lexmark Network Card Reader icon.
4 From the Source list, choose the printer that you want to use, and then click
Thumbnails of the photos stored on the memory device appear on the dialog.
5 If you want to enlarge the thumbnails, then click and drag the slider
6 Select the photos that you want to save, and then click Save.
7 Browse to the location of the folder where you want to save the photos and documents, and then click Save.
If the printer is connected to the computer through a USB cable, and you have set an application to launch when a memory device is connected to the computer, then the application automatically launches. Use it to transfer photos to the computer.
Working with photos

1 Insert a memory card into the printer.
2 After the memory card is detected, press the arrow buttons until Save Photos appears.
3 Insert the flash drive into the printer, and then press the arrow buttons until USB Flash Drive appears.
4 Use the arrow buttons to select a save option. You can transfer all the photos, the most recent photo, or photos within a date range. Press when you make a selection.
5 Follow the instructions on the printer control panel display.
For more options on printing photos and customizing photos, see the Help associated with the programs installed with the printer software.
1 Load photo paper with the glossy or printable side facing you. (If you are not sure which side is the printable side, see the instructions that came with the paper.)
2 From the printer control panel, press .
3 Insert a memory card, flash drive, or digital camera set to mass storage mode.
4 Press the arrow buttons until Easy Photo or Print Photos appears, and then press .
5 Press the arrow buttons to select an option on printing photos, and then press .
Working with photos

each time you make a selection.
7 Press .
1 Load photo paper with the glossy or printable side facing you. (If you are not sure which side is the printable side, then see the instructions that came with the paper.)
2 To print the photos:
a Do one of the following:
. • In Windows XP and earlier, click Start. b Click All Programs or Programs, and then select the printer program folder from the list.
c Select Lexmark Productivity Studio.
with the program.
a Customize the settings as needed in the Page Setup dialog.
1 With a photo open, choose File Page Setup. 2 From the “Format for” pop-up menu, choose the printer. 3 From the Paper Size pop-up menu, choose a paper size. 4 Click OK. b Customize the settings as needed in the Print dialog.
1 With a photo open, choose File Print. 2 From the Printer pop-up menu, choose the printer.
Working with photos

1 Load photo paper with the glossy or printable side facing you. (If you are not sure which side is the printable side, then see the instructions that came with the paper.)
2 Insert a memory card, flash drive, or digital camera set to mass storage mode.
3 From the printer control panel, press .
4 Press the arrow buttons until Save Photos appears, and then press .
5 Transfer the photos to the computer.
a Press . b If you are using Windows:
If you installed Lexmark Productivity Studio, then it launches when you insert the memory device. Follow the instructions on the computer screen to transfer the photos to the computer, and then use the programs installed on the computer to print the photos. If you are using Macintosh: If you have iPhoto installed on the computer, then it launches when you insert the memory device. Follow the instructions on the computer screen to transfer the photos to the computer, and then use the applications installed on the computer to print the photos.
a Press the arrow buttons until Network appears, and then press .
b If prompted, press the arrow buttons to select the network computer where you want to save the photos,
and then press . c If you are using Windows:
1 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start. 2 Click All Programs or Programs, and then select the printer program folder from the list. 3 Click Lexmark Productivity Studio. 4 From the Photo Printing section of the main screen, click Download to library. 5 Browse to the location of the memory device, and then click Transfer. 6 Select the network printer. 7 Follow the instructions on the computer screen to transfer and print the photos. If you are using Macintosh:
Working with photos

If the printer is connected to the computer through a network, then the Lexmark Network Card Reader launches on the computer. Transfer the photos to the computer using the application, and then use the applications installed on the computer to print the photos. For more information on transferring photos using the Lexmark Network Card Reader, see the Help associated with the application.
You can use the printer control panel to apply color effects to your photos.
1 Load photo paper with the glossy or printable side facing you. (If you are not sure which side is the printable side, then see the instructions that came with the paper.)
2 From the printer control panel, press .
3 Insert a memory card or flash drive.
4 Press the arrow buttons until Print Photos appears.
5 Press the arrow buttons to select an option on how to print the photos, and then press .
Lighter/Darker appears on the display.
6 Press the arrow buttons to adjust the brightness of the photo, and then press .
Photo Effects appears on the display.
7 Press the arrow buttons to select a color effect. You can choose to auto-enhance the photo, or print the photo in sepia, antique grey, or antique brown. Press when you make a selection.
8 Use the arrow buttons to select the photo size, paper size, paper type, layout, and quality of the photos. Press each time you make a selection.
9 Press to print the photos.
Working with photos

PictBridge is a technology available in most digital cameras that lets you print directly from your digital camera without using a computer. You can connect a PictBridge-enabled digital camera to the printer, and use the camera to control printing photos.
1 Insert one end of the USB cable into the camera.
2 Insert the other end of the cable into the PictBridge port on the front of the printer.


3 If the PictBridge connection is successful, then the following message appears on the display: PictBridge Camera detected. Press OK to change settings.
4 Use the camera to choose and print photos. If desired, you can also use the Pictbridge menu to select the paper size, paper type, photo size, and layout of the photos that you want to print.
Press to access the PictBridge menu, and then press each time you make a selection.
Working with photos

1 Load letter- or A4-size plain paper.
2 From the printer control panel, press .
3 Insert a memory card or flash drive.
4 Press the arrow buttons until Proof Sheet appears, and then press .
5 Press the arrow buttons to select an option to print a proof sheet.
You can print a proof sheet:
6 Press .
The proof sheets prints.
7 Follow the instructions on the proof sheet to select which photos to print, the number of copies per photo, red-eye reduction, page layout, print options, and paper size.
8 Load the proof sheet facedown on the scanner glass.
Scan Proof Sheet appears on the display.
9 Press .
The printer scans the proof sheet.
10 Load photo paper vertically in the center of the paper support, with the glossy or printable side facing you. (If you are not sure which side is the printable side, then see the instructions that came with the paper.)
11 Press to print the photos.
Working with photos

Digital Print Order Format (DPOF) is a feature available on some digital cameras. If your camera supports DPOF, then you can specify which photos to print, how many of each, and the print settings while the memory card is still in the camera. The printer recognizes these settings when you insert the memory card into the printer or connect the camera to the printer.
1 Load photo paper with the glossy or printable side facing you. (If you are not sure which side is the printable side, then see the instructions that came with the paper.)
2 Insert a memory card.
When the printer detects the memory card, the message Memory Card Detected appears on the printer control panel display.
3 Press the arrow buttons until Print Photos appears, and then press .
4 Press the arrow buttons until Print DPOF appears, and then press to print the photos.
Working with photos

Making copies
1 Load paper.
2 Load the original document facedown on the scanner glass.
3 From the printer control panel, press .
4 Press the arrow buttons to select the number of copies, and then press or to set a color or black-and-white copy.
5 Press .
1 Load photo paper with the glossy or printable side facing you. (If you are not sure which side is the printable side, then see the instructions that came with the paper.)
2 Place a photo facedown on the scanner glass.
3 From the printer control panel, press .
4 Press until Photo Reprint appears.
5 Press the arrow buttons until Yes appears, and then press .
6 Press the arrow buttons until the desired paper size appears. If your desired paper size is not on the list, select Other. Additional paper size options appear on the display.
Press when you make a selection.
7 Press .
1 Load paper.
2 Load an original document facedown on the scanner glass.
3 From the printer control panel, press .
4 Press until Resize appears.
Copying

5 Press the arrow buttons until the setting that you want appears.
6 Press .
1 Load paper.
2 Load an original document facedown on the scanner glass.
3 From the printer control panel, press .
4 Press until Quality appears.
5 Press the arrow buttons to set the copy quality to Automatic, Draft, Normal, or Photo, and then press to save your setting.
6 Press .
1 Load paper.
2 Load an original document facedown on the scanner glass.
3 From the printer control panel, press .
4 Press until Lighter/Darker appears.
5 Press the arrow buttons to adjust the slider, and then press to save your setting.
6 Press .
Copying

If you print multiple copies of a document, then you can choose to print each copy as a set (collated) or to print the copies as groups of pages (not collated).
1 Load paper.
2 Load an original document facedown on the scanner glass.
3 From the printer control panel, press .
4 Press the arrow buttons to select the number of copies, and then press .
5 Press until Collate appears.
6 Press the arrow buttons until On appears.
7 Press to save the image of the page to the printer memory.
8 When prompted if you want to scan another page, press .
9 Load the next page of the original document facedown on the scanner glass, and then press .
10 Repeat steps 8 and 9 until all the pages that you want to copy have been saved to the printer memory.
11 When prompted if you want to scan another page, press the arrow buttons until No appears, and then press to start printing the copies.
You can print the same page image multiple times on one sheet of paper. This option is helpful when creating labels, decals, flyers, handouts, and so on.
1 Load paper.
2 Load an original document facedown on the scanner glass.
3 From the printer control panel, press .
4 Press until Copies per Sheet appears.
5 Press the arrow buttons to choose the number of times that an image is repeated on a page: once, four times, nine times, or 16 times.
6 Press .
Collated Not collated · Copying

The N-Up setting lets you copy multiple pages on one sheet by printing smaller images of each page. For example, you can condense a 20-page document into 5 pages if you use the N-Up setting to print 4 page images per sheet.
1 Load paper.
2 Load an original document facedown on the scanner glass.
3 From the printer control panel, press .
4 Press until Pages per Sheet appears.
5 Press the arrow buttons to choose the number of pages that you want to copy on a sheet of paper. You may choose to copy one, two, or four page images on a sheet.
6 Press to save the image of the page to the printer memory.
7 When prompted if you want to scan another page, press to choose Yes.
8 Load the next page of the original document facedown on the scanner glass, and then press .
9 Repeat steps 7 and 8 until all the pages that you want to copy have been saved to the printer memory.
10 When asked if you want to scan another page, press the arrow buttons until No appears, and then press to start printing.
1 Press .
Scanning stops and the scanner bar returns to its home position.
2 Press to turn off the printer.
Copying

For more options on scanning and customizing scanned images, see the Help associated with the programs installed with the printer software.
You can scan and then print photos, text documents, magazine articles, newspapers, and other publications. You can also scan a document for faxing.
1 Open the top cover, and then load an original document facedown on the scanner glass.

2 Close the top cover to avoid dark edges on the scanned image.
3 From the printer control panel, press .
Scan to appears on the display. You can send the scanned image to a computer, flash drive, memory card, or to a computer over a network.
c Press the arrow buttons until the application that you want appears, and then press . d Use the arrow buttons to select the quality and original image size, and then press each time you make a selection. e Press . • If you choose to send the scanned image to a memory card or flash drive: a Insert the memory device.
Scanning

c Use the arrow buttons to select the quality and original image size, and then press each time you make a selection. d Press .
Note: Do not remove the memory device until the menu indicates that the file has been saved. • If you choose to send the scanned image to a computer over the network (selected models only): a Press the arrow buttons until Network appears, and then press . b If prompted, press the arrow buttons until the computer name of the network computer appears, and
then press .
– You may be prompted to enter a PIN if the computer requires it. To assign a computer name and a
PIN to the network computer, see the Help for the printer software associated with your operating system. – Use the arrow buttons to increase or decrease the value for each digit (the default value is 0000) in
the PIN, and then press each time you select a digit. c Wait until the printer has finished downloading the scan applications list. d Press the arrow buttons until the application that you want appears, and then press . e Use the arrow buttons to select the quality and original image size, and then press each time you make a selection. f Press .
1 Open the top cover, and then load an original document facedown on the scanner glass.
2 Close the top cover to avoid dark edges on the scanned image.
3 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start.
4 Click All Programs or Programs, and then select the printer program folder from the list.
5 Click Lexmark Productivity Studio.
6 From the Photo Printing section of the main screen, click Scan.
7 Follow the instructions on the computer screen.
1 Open the top cover, and then load an original document facedown on the scanner glass.
2 Close the top cover to avoid dark edges on the scanned image.
3 From the Finder desktop, double-click the printer folder.
4 Double-click XXXX Series Center, where XXXX is the printer series.
5 From the “What is being scanned?” menu, choose the type of document to be scanned.
6 Click Scan.
Scanning

1 Open the top cover, and then load an original document facedown on the scanner glass.
2 Close the top cover to avoid dark edges on the scanned image.
3 From the printer control panel, press .
4 Press the arrow buttons to choose where to send the scanned image. You can send the scanned image to a computer, flash drive, memory card, or to a computer over a network.
5 When the destination that you want appears, press .
6 To scan black-and-white documents, press .
7 Press .
1 Open the top cover, and then load an original document facedown on the scanner glass.
2 Close the top cover to avoid dark edges on the scanned image.
3 From the printer control panel, press .
4 Press the arrow buttons until Computer or Network appears, and then press .
5 Wait for the printer to finish downloading the applications list.
6 From the list of applications, press the arrow buttons until the application that you want appears.
7 Press .
The scanned image is sent to the photo-editing application that you selected.
2 Load an original document facedown on the scanner glass.
3 From the printer control panel, press .
Scanning

4 Press the arrow buttons until Network appears, and then press .
5 If prompted, press the arrow buttons to select the computer name of the network computer where you want to send the scanned image, and then press .
6 Wait until the printer has finished downloading the scan applications list.
7 Press the arrow buttons until the application that you want appears, and then press .
8 Press .
To cancel a scan job started in the printer control panel, press .
To cancel a scan job started in the Lexmark Productivity Studio, click Stop on the computer screen.
To cancel a scan job started in the Lexmark All-in-One Center, click Cancel on the computer screen.
Scanning

Before you send a fax, make sure:
You can scan a document to the computer and then fax it to someone using the software.
1 Load an original document facedown on the scanner glass.
2 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start.
3 Click All Programs or Programs, and then select the printer program folder from the list.
4 Click Lexmark Productivity Studio.
5 From the Welcome Screen, click Fax.
6 Select the Document option.
7 Click Start.
8 Enter the recipient information, and then click Next.
9 Enter the cover page information, and then click Next.
10 If there are any additional documents that you want to send with your fax, add these now, and then click Next.
12 If you want a paper copy of your fax, then select Print a copy of your fax.
13 Click Send.
Faxing

1 Load an original document facedown on the scanner glass.
2 From the Finder desktop, double-click the printer folder.
3 Double-click XXXX Series Center, where XXXX is the printer series.
4 From the “What is being scanned?” menu, choose the type of document to be scanned.
5 From the “How will the scanned image be used?” pop-up menu, choose To be faxed.
6 From the “Send scanned image to” pop-up menu, choose Preview.
7 If you have more than one page to fax, select Prompt for multiple pages.
8 Click Scan.
The Scan dialog appears with a preview of the document.
9 From the Scan dialog, click File Print.
11 In the “To” field, enter the fax number of the recipient.
You can also click
to choose a recipient from the Address Book, a built-in application in Macintosh. The Address Book shows only contacts with fax numbers.
12 If you want to include a cover page, select Use Cover Page, and then enter the subject of the fax and a message for the recipient.
13 Click Fax.
1 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start.
2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Click Lexmark Productivity Studio.
4 From the Settings area in the left pane of the Welcome screen, click Set up and manage faxes.
5 From the “I Want To” menu, click Adjust speed dial list and other fax settings.
6 Click the Ringing and Answering tab.
7 From the “Automatically answer incoming calls as a fax” area, select On from the Auto Answer drop-down list.
8 To turn the Auto Answer feature on and off at scheduled times, select the settings that you want from the drop-down lists.
Faxing

9 To set the number of telephone rings before the printer automatically receives faxes, select a setting from the “Pick-up on the” drop-down list in the “Answering on your phone line type” area.
10 Click OK to save the settings.
1 From the menu bar, click
System Preferences.
2 Click Print & Fax.
3 From the Faxes list, click Internal Modem.
4 Click Receive Options.
5 Select Receive faxes on this computer.
6 Select Print to, and then choose the printer from the pop-up menu.
7 Customize other settings as needed, and then click OK.
1 From the menu bar, click
System Preferences.
2 Click Print & Fax.
3 Click the Faxing tab.
4 Select Receive faxes on this computer.
5 Click Set Up Fax Modem.
The Fax list appears.
6 Click Internal Modem, and then close the Fax list.
7 Select Print on printer, and then choose the printer from the pop-up menu.
8 Customize other settings as needed.
1 From the menu bar, click
System Preferences.
2 Click Print & Fax.
3 Click the Faxing tab.
4 Select Receive faxes on this computer.
5 Select Print on printer, and then choose the printer from the pop-up menu.
6 Customize other settings as needed.
Faxing

Maintaining print cartridges
1 Open the printer, and then press down on the cartridge carrier levers.

2 Remove the used print cartridge or cartridges.
3 If you are installing new print cartridges, remove the tape from the back and bottom of the color cartridge, insert the cartridge in the right carrier, and then close the color cartridge carrier lid.

Maintaining the printer

4 If a black cartridge is included in the box contents, remove the tape from the back and bottom of the black cartridge, insert the cartridge in the left carrier, and then close the black cartridge carrier lid.

5 Close the printer, making sure to keep your hands out from underneath the scanner unit.

1 Make sure the printer is on.
2 Lift the scanner unit.
Maintaining the printer

The print cartridge carrier moves and stops at the loading position, unless the printer is busy.

3 Press down on the cartridge carrier latch to raise the cartridge carrier lid.

4 Remove the used print cartridge.
The warranty does not cover repair of failures or damage caused by a refilled cartridge. Lexmark does not recommend use of a refilled cartridge. Refilling a cartridge can affect print quality and may cause damage to the printer. For best results, use Lexmark supplies.
Lexmark printers, print cartridges, and photo paper are designed to perform together for superior print quality.
If you receive an Out of Original Lexmark Ink message, the original Lexmark ink in the indicated cartridge (s) has been depleted.
If you believe you purchased a new, genuine Lexmark print cartridge, but the Out of Original Lexmark Ink message appears:
1 Click Learn More on the message.
2 Click Report a non-Lexmark print cartridge.
To prevent the message from appearing again for the indicated cartridge(s):
Maintaining the printer

Lexmark's warranty does not cover damage caused by non-Lexmark ink or print cartridges.
1 Load plain Letter-size paper.
2 From the printer control panel, press , and then press .
3 Press the arrow buttons until Align Cartridges appears, and then press .
An alignment page prints.
1 Load plain Letter-size paper.
2 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start.
3 Click All Programs or Programs, and then select the printer program folder from the list.
4 From the printer folder, click Maintenance Align Cartridges.
5 Click Print.
6 Follow the instructions on the computer screen.
1 Load plain Letter-size paper.
2 From the Finder desktop, double-click the printer folder.
3 Double-click the printer utility icon.
4 From the Maintenance tab, click Print Alignment Page.
5 Follow the instructions on the computer screen.
If you aligned the cartridges to improve print quality, print your document again. If print quality has not improved, then clean the print cartridge nozzles.
1 Load plain Letter-size paper.
2 From the printer control panel, press , and then press .
Maintaining the printer

3 Press the arrow buttons until Clean Cartridges appears, and then press .
A page prints, forcing ink through the print cartridge nozzles to clean them.
4 Print the document again to verify that the print quality has improved.
1 Load plain Letter-size paper.
2 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start.
3 Click All Programs or Programs, and then select the printer program folder from the list.
4 From the printer folder, click Maintenance Clean Cartridges.
5 Click Print.
A page prints, forcing ink through the print cartridge nozzles to clean them.
6 Print the document again to verify that the print quality has improved.
1 Load plain Letter-size paper.
2 From the Finder desktop, double click the printer folder.
3 Double-click the printer utility icon.
4 From the Maintenance tab, click Clean Print Nozzles.
A page prints, forcing ink through the print cartridge nozzles to clean them.
5 Print the document again to verify that the print quality has improved.
If print quality has not improved, then try cleaning the nozzles up to two more times, or wipe the print cartridge nozzles and contacts.
1 From the printer control panel, press , and then press .
2 Press again.
3 Press the arrow buttons until Color Ink appears, and then press .
Check the ink level of the color cartridge. Install a new cartridge if necessary.
4 Press .
5 If a black cartridge is included in the box contents, and if you have installed a black cartridge in the printer, then press the arrow buttons until Black Ink appears, and then press .
Check the ink level of the black cartridge. Install a new cartridge if necessary.
6 Press until you exit Setup, or press another mode button.
Maintaining the printer

Use the Lexmark Service Center to check the ink levels of the cartridges.
1 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start.
2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Select Lexmark Service Center.
4 If you have not yet downloaded the Lexmark Service Center, download it.
5 Check the ink levels of the cartridges on the Printer Maintenance page.
Install a new cartridge if necessary.
1 From the Finder desktop, double click the printer folder.
2 Double-click the printer utility icon.
The Lexmark Printer Utility appears.
3 If an exclamation point (!) appears on a print cartridge, then the ink level is low. Install a new cartridge if necessary.
1 Remove the print cartridge(s).
2 Dampen a clean, lint-free cloth with water, and then place the cloth on a flat surface.
3 Gently hold the nozzles against the cloth for about three seconds, and then wipe in the direction shown.
Maintaining the printer

4 Using another clean section of the cloth, gently hold the cloth against the contacts for about three seconds, and then wipe in the direction shown.
5 With another clean section of the cloth, repeat step 3 and step 4, and then let the nozzles and contacts dry completely.
6 Reinsert the print cartridge(s), and then print the document again.
7 If the print quality does not improve, clean the print nozzles, and then try printing the document again.
8 Repeat step 7 up to two more times.
9 If print quality is still not satisfactory, replace the print cartridge(s).
1 Dampen a clean, lint-free cloth with water.
2 Gently wipe the scanner glass clean.
1 Make sure that the printer is turned off and unplugged from the wall outlet.
2 Remove paper from the paper support and paper exit tray.
Maintaining the printer

3 Dampen a clean, lint-free cloth with water.
4 Wipe only the outside of the printer, making sure to remove any ink residue that has accumulated on the paper exit tray.
5 Make sure the paper support and paper exit tray are dry before beginning a new print job.
Lexmark 3600-4600 Series models (except Lexmark 3690 and Lexmark 4690)
Item Part number Average cartridge standard page yield is up to1
Black cartridge2 36
High yield black cartridge 36XLA
High yield black cartridge2 36XL
Page yield values available at www.lexmark.com/pageyields.
Color cartridge2 37
High yield color cartridge 37XLA
High yield color cartridge2 37XL
Photo cartridge 31 Not applicable
1 Values obtained by continuous printing. Declared yield value in accordance with ISO/IEC 24711.
2 Licensed Return Program Cartridge
Lexmark 3690 and Lexmark 4690 models
Item Part number Average cartridge standard page yield is up to1
Page yield values available at www.lexmark.com/pageyields. Black cartridge2 4
Color Cartridge2 5
Photo cartridge 31 Not applicable
1 Values obtained by continuous printing. Declared yield value in accordance with ISO/IEC 24711.
2 Licensed Return Program Cartridge

To purchase supplies or to locate a dealer near you, visit our Web site at www.lexmark.com.
For best results when printing photos or other high-quality images, use Lexmark Photo Paper or Lexmark PerfectFinish Photo Paper and Lexmark print cartridges.
USB cable Part number 1021294
You can reset your printer to the original settings without using the printer menus.
1 Turn off the printer.
2 From the printer control panel, press and hold and , and then press to turn the printer on.
1 From the printer control panel, press .
2 Press the arrow buttons until Defaults appears, and then press .
3 Press the arrow buttons until Set Defaults appears, and then press .
4 Press the arrow buttons until Use Factory appears, and then press .
5 Press again.
6 When prompted, press the arrow buttons to select a language, and then press .
7 Press the arrow buttons to select a country, and then press .
Initial Setup Complete appears on the display.
Item Description · Maintaining the printer

Using the printer troubleshooting software (Windows only)
The Lexmark Service Center provides step-by-step troubleshooting help and contains links to printer maintenance tasks and customer support.
To open the Lexmark Service Center, use one of these methods:
Method 1 Method 2
If it appears on an error message dialog, click the For additional assistance, use the Lexmark Service Center link.
1 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start. 2 Click All Programs or Programs, and then select the printer program folder from the list. 3 Select Lexmark Service Center.
These are possible solutions. Try one of the following:
During initial setup, and every time you reset the printer to factory default settings, you will be asked to select a language.
To select a language, press the arrow buttons until the language that you want appears on the display, and then press .
In case the wrong language was set during initial setup, you can still change the language settings of the printer.
1 From the printer control panel, press .
2 Press , and then press .
3 Press again.
4 Press the arrow buttons until the language that you want appears on the display, and then press .
5 If you are sure, press to change the language.
Troubleshooting

These are possible solutions. Try one or more of the following:
Make sure the printer is on by pressing .
1 Disconnect the power cord from the wall outlet, and then from the printer.
2 Plug the cord all the way into the power supply on the printer.
3 Plug the cord into an electrical outlet that other electrical devices have been using.
4 If the light is not on, press .
If you encountered problems while installing, or if your printer does not appear in the list in the Printers folder or as a printer option when sending a print job, you can try uninstalling and reinstalling the software.
These are some other possible solutions. Try one or more of the following:
The following operating systems are supported: Windows Vista, Windows XP, Windows 2000 with Service Pack 3 or later, and Mac OS X versions 10.5, 10.4 and 10.3.
CHECK THAT YOUR COMPUTER MEETS THE MINIMUM SYSTEM REQUIREMENTS LISTED ON THE
C HECK THE USB CONNECTION
1 Check the USB cable for any obvious damage. If the cable is damaged, use a new one.
2 Firmly plug the square end of the USB cable into the back of the printer.
3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.
The USB port is marked with the USB symbol.
Troubleshooting

1 Press to turn the printer off.
2 Disconnect the power cord from the wall outlet.
3 Gently remove the power supply from the printer.
4 Reconnect the power supply to the printer.
5 Plug the power cord into the wall outlet.
6 Press to turn the printer on.
1 Close all open programs.
2 Disable any security programs.
3 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start.
4 Click Computer or My Computer.
5 Double-click the CD or DVD drive icon.
6 If necessary, double-click setup.exe.
7 Follow the instructions on the computer screen to install the software.
8 When the installation is completed, enable the security software again.
These are possible solutions. Try one or more of the following:
If an error message appears, then resolve the error before trying to print again.
If the light is not on, then make sure that the power cord is properly connected to the printer and plugged into a known working electrical outlet that other electrical devices have been using.
C HECK INK
Check the ink levels, and then install new print cartridges if necessary.
Troubleshooting

1 Remove the print cartridges.
2 Make sure the sticker and tape have been removed.
3 Reinsert the cartridges.
1 Do one of the following:
. b Click Control Panel.
c Under Hardware and Sound, click Printer.
a Click Start. b Click Printers and Faxes.
a Click Start. b Click Settings Printers.
2 Double-click the printer.

For Mac OS X version 10.5
System Preferences Print & Fax.
1 From the Finder desktop, click
2 From the Default Printer pop-up menu, check if the printer is the default printer.
If the printer is not the default printer, then you must select the printer for each file that you want to print.
If you want to set the printer as the default printer, then select the printer from the Default Printer pop-up menu.
3 Click Open Print Queue.
The print queue dialog appears.
Make sure that the print job is not on hold. If the print job is on hold:
For Mac OS X version 10.4 and earlier
1 From the Finder desktop, click Go Utilities Print Center or Printer Setup Utility.
The Printer List dialog appears.
2 Double-click the printer.
The print queue dialog appears.
If the print job is on hold:
– If you want to resume a particular print job, choose the document name, and then click Resume. – If you want to resume all print jobs in the queue, then click Start Jobs. • If the printer is not in bold, then it is not the default printer. You must select the printer for each file that you want to print.
If you want to set the printer as the default printer:
a Go back to the Printer List dialog, and then select the printer. b Click Make Default.
1 Press to turn off the printer.
2 Disconnect the power cord from the wall outlet.
3 Remove the power supply from the printer.
4 Reconnect the power supply to the printer.
5 Plug the power cord into the wall outlet.
6 Press to turn on the printer.
Troubleshooting

If you encountered problems while installing, or if your printer does not appear in the printers folder or as a printer option when sending a print job, then try uninstalling and reinstalling the software.
The printer and the computer cannot exchange data.
These are possible solutions. Try one or more of the following:
1 Press to turn the printer off.
2 Disconnect the power cord from the wall outlet.
3 Remove the power supply from the printer.
4 Reconnect the power supply to the printer.
5 Plug the power cord into the wall outlet.
6 Press to turn the printer on.
If the power light is blinking on and off slowly, then the printer is in sleep mode.
1 Unplug the power cord from the wall outlet.
2 Wait ten seconds, and then insert the power cord into the wall outlet.
3 Press to turn the printer on.
If the printer is not functioning properly, or if a communications error message appears when you try to use the printer, then you may need to remove and reinstall the printer software.
1 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start.
2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Select Uninstall.
4 Follow the instructions on the computer screen to remove the printer software.
5 Restart the computer before reinstalling the printer software.
6 Click Cancel on all New Hardware Found screens.
7 Insert the installation CD, and then follow the instructions on the computer screen to reinstall the software.
Troubleshooting

If the install screen does not appear automatically after you restart your computer, do one of the following:
. b In the Start Search box, type D:\setup.exe, where D is the letter of your CD or DVD drive.
a Click Start. b Click Run.
c Type D:\setup.exe, where D is the letter of your CD or DVD drive.
1 Close all open software applications.
2 From the Finder desktop, double-click the printer folder.
3 Double-click the Uninstaller icon.
4 Follow the instructions on the computer screen to remove the printer software.
5 Restart the computer before reinstalling the printer software.
6 Insert the installation CD, and then follow the instructions on the computer screen to reinstall the software.
If the software still does not install correctly, visit our Web site at www.lexmark.com to check for the latest software.
1 In all countries or regions except the United States, select your country or region.
2 Click the links for drivers or downloads.
3 Select your printer family.
4 Select your printer model.
5 Select your operating system.
6 Select the file that you want to download, and then follow the instructions on the computer screen.
To confirm that the USB port is enabled on the computer:
1 Do one of the following:
Control Panel. b Click System and Maintenance System.
c Click Device Manager.
a Click Start. b Click Control Panel Performance and Maintenance System.
a Click · a Click · Troubleshooting

c From the Hardware tab, click Device Manager.
a Click Start. b Click Settings Control Panel System.
c From the Hardware tab, click Device Manager.
2 Click the plus sign (+) beside Universal Serial Bus Controller.
If USB Host Controller and USB Root Hub are listed, then the USB port is enabled.
For more information, see the computer documentation.
Before beginning to troubleshoot the wireless printer, verify the following:
Print a network setup page to verify the SSID the printer is using.
If you are not sure if your SSID is correct, run the wireless setup again.
Log into the wireless access point (wireless router) and check the security settings.
A security key is like a password. All devices on the same wireless network using WEP, WPA, or WPA2 share the same security key.
If you are not sure if your security information is correct, run the wireless setup again.
Try accessing other computers on your wireless network.
If your network has Internet access, try connecting to the Internet over a wireless connection.
For most networks, the printer should be within 100 feet (30 meters) of the wireless access point (wireless router).
Remove any large metal objects between the access point and the printer.
Make sure the printer and wireless access point are not separated by poles, walls, or support columns containing metal or concrete.
Many devices can interfere with the wireless signal, including baby monitors, motors, cordless phones, security system cameras, other wireless networks, and some Bluetooth devices.
Troubleshooting

A network setup page lists the configuration settings of the printer, including the IP address and MAC address of the printer. You can print a network setup page only if your printer has an internal wireless print server.
1 Load plain paper.
2 From the printer control panel, press .
3 Press the arrow buttons until Network Setup appears, and then press .
Print Setup Page appears on the display.
4 Press .
5 Press again.
The network setup page prints.
If the configuration software does not allow you to continue configuring your printer wirelessly after you attach the USB cable, there may be a problem with the cable. Try one or more of the following:
Troubleshooting

2 Attach the small, square connector to the printer.
If you encountered problems while installing, or if your printer does not appear in the printers folder or as a printer option when sending a print job, you can try uninstalling and reinstalling the software.
These are possible solutions. Try one or more of the following:
MAKE SURE YOUR COMPUTER IS CONNECTED TO YOUR WIRELESS ACCESS POINT (WIRELESS
MOVE THE COMPUTER AND/OR PRINTER CLOSER TO THE WIRELESS ROUTER
Although the possible distance between devices in 802.11b or 802.11g networks is 300 feet, the maximum range for optimal performance is generally 100–150 feet.
There may be temporary interference from other devices such as microwave ovens or other appliances, cordless phones, baby monitors, and security system cameras. Make sure your access point is not positioned too closely to these devices.
CHECK WHETHER THE PRINTER IS ON THE SAME WIRELESS NETWORK AS THE COMPUTER
Print a network setup page. Refer to the documentation that came with your printer for details on printing a network setup page.
Make sure the SSID the printer is using matches the wireless network SSID. If you are not sure how to find the network SSID, use one of the following:
1 Type the IP address of the wireless access point (wireless router) in the Web address field of your browser.
Troubleshooting

If you do not know the IP address of the wireless access point:
a Do one of the following:
. 2 Click All Programs Accessories. 3 Click Command Prompt.
In Windows XP and earlier
1 Click Start. 2 Click All Programs or Programs Accessories Command Prompt. b Type ipconfig.
c Press Enter.
2 Type your user name and password for the wireless access point (wireless router) when prompted.
3 Click OK.
4 On the main page, click Wireless or another selection where settings are stored. The SSID appears.
5 Write down the SSID, security type, and the WEP key/WPA passphrase (if shown).
6 Store the SSID and the WEP key or WPA passphrase in a safe place for future reference.
In Mac OS X version 10.5
1 From the menu bar, click
System Preferences.
2 Click Network.
3 Click AirPort.
The SSID of the network the computer is connected to is displayed in the Network Name pop-up menu.
4 Write down the SSID.
In Mac OS X version 10.4 and earlier
1 From the menu bar, click Go Applications.
2 From the Applications folder, double-click Internet Connect.
3 From the toolbar, click AirPort.
The SSID of the network the computer is connected to is displayed in the Network pop-up menu.
4 Write down the SSID.
In Windows Vista · 1 Click · Troubleshooting

1 Type the IP address of the wireless access point (wireless router) in the Web address field of your browser and continue to Step 2.
If you do not know the IP address of the wireless access point (wireless router), then do the following:
In Mac OS X version 10.5
System Preferences. b Click Network.
a From the menu bar, click
c Click AirPort. d Click Advanced. e Click TCP/IP.
The “Router” entry is typically the wireless access point (wireless router).
In Mac OS X version 10.4 and earlier
System Preferences. b Click Network.
a From the menu bar, click
c From the Show pop-up menu, select Airport. d Click TCP/IP.
The “Router” entry is typically the wireless access point (wireless router).
2 Type your user name and password when prompted.
3 Click OK.
4 On the main page, click Wireless or another selection where settings are stored. The SSID will be displayed.
5 Write down the SSID, security type and the WEP key/WPA passphrase (if shown).
Must meet one of the following criteria:
or • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard. ASCII characters in a WEP key are case-sensitive.
Troubleshooting

Must meet one of the following criteria:
or • Exactly 64 hexadecimal characters. Hexadecimal characters are A-F, a-f, and 0-9.
Third-party (non-Microsoft) firewalls can interfere with wireless printing. If the printer and computer are configured correctly, and the wireless network is working, but the printer will not print wirelessly, a firewall could be the problem. If there is a firewall (other than the Windows firewall) on the computer, try one or more of the following:
C HECK POWER
Make sure the light is on.
Wi-Fi indicator light is green but the printer does not print (Windows only)
If you have completed the configuration for wireless printing and all of the settings appear to be correct, but the printer does not print, try one or more of the following:
Do not attempt to print, remove the installation CD, or detach the installation cable until you see the Wireless Setup Successful screen.
Troubleshooting

Confirm that the printer is enabled.
1 Do one of the following:
. b Click Control Panel.
c Under Hardware and Sound, click Printer.
a Click Start. b Click Printers and Faxes.
a Click Start. b Click Settings Printers.
2 Right-click the new printer. If you see Use Printer Online in the menu, select it.
3 Close the Printers or Printers and Faxes window and try printing again.
If you have previously set up your printer as a locally attached printer, you may need to select the wireless printer to use the printer wirelessly.
1 Do one of the following:
. b Click Control Panel.
c Under Hardware and Sound, click Printer.
a Click Start. b Click Printers and Faxes.
a Click Start. b Click Settings Printers.
2 Check to see if you have a printer called Copy 1 in your folder. If you do, right-click the Copy 1 printer and click Use Printer Online from the menu.
3 Close the Printers or Printers and Faxes window and try printing again.
a Click · a Click · Troubleshooting

If you have previously set up your printer as a locally attached printer, you may need to select the wireless printer to use the printer wirelessly.
1 Do one of the following:
. b Click Control Panel.
c Under Hardware and Sound, click Printer.
a Click Start. b Click Printers and Faxes.
a Click Start. b Click Settings Printers.
2 Right-click the printer, and then select Properties from the menu.
3 Click the Ports tab.
4 Locate the selected port. The selected port has a check in the Port column.
5 If the Description column of the selected port indicates that it is a USB port, scroll through the list and select the port with Printer Port in the Description column.
6 Click OK, and then try to print again.
When the Wi-Fi indicator light is blinking orange, it indicates that the printer has been set up for wireless networking but cannot connect to the network for which it has been configured. The printer may be unable to join the network because of interference, its distance from the wireless access point (wireless router), or until its settings are changed.
These are possible solutions. Try one or more of the following:
Check the access point and, if necessary, turn it on.
There may be temporary interference from other devices such as microwave ovens or other appliances, cordless phones, baby monitors, and security system cameras. Make sure your access point is not positioned too closely to these devices.
a Click · Troubleshooting

Antennas usually work best if they are pointing straight up. You may find that reception improves if you experiment with different angles for the printer and/or wireless access point antennas.
Move the printer closer to the access point. Although the possible distance between devices in 802.11b or 802.11g networks is 300 feet, the maximum range for optimal performance is generally 100–150 feet.
You can find the signal strength of the network on the network setup page.
A valid WEP key is:
or • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard.
A valid WPA passphrase is:
or • Exactly 64 hexadecimal characters. Hexadecimal characters are A-F, a-f, and 0-9.
If your wireless network is not using security, then you will not have a security key. Using a wireless network with no security is not recommended because it can allow intruders to use your network resources without your consent.
If your network uses MAC address filtering, make sure that you include the MAC address of the printer in the MAC address filter list. This will allow the printer to operate on the network. For more information, see “How do I find the MAC address?” on page 51.
1 If you do not already know it, find the IP address of the access point. a Do one of the following:
. 2 Click All Programs Accessories. 3 Click Command Prompt.
1 Click Start. 2 Click All Programs or Programs Accessories Command Prompt.
1 Click · Troubleshooting

b Type ipconfig.
c Press Enter.
2 Ping the access point. a Do one of the following:
. 2 Click All Programs Accessories. 3 Click Command Prompt.
1 Click Start. 2 Click All Programs or Programs Accessories Command Prompt. b Type ping followed by a space and the IP address of the wireless access point. For example:
ping 192.168.0.100
c Press Enter.
Try the following:
a Do one of the following:
. 2 Click Control Panel. 3 Click Network and Internet. 4 Click Network and Sharing Center.
1 Click Start. 2 Click Control Panel. 3 Click Network Connection. b Select the appropriate connection from the ones shown.
1 Click · 1 Click · Troubleshooting

If your wireless settings have changed, you must run the printer wireless setup again. Some reasons your settings may have changed include your having manually changed your WEP or WPA keys, channel, or other network settings; or the access point having been reset to factory defaults.
Running the wireless setup again can also resolve issues due to misconfigurations that occurred when configuring the printer for wireless access.
1 Do one of the following: • In Windows Vista, click
. • In Windows XP and earlier, click Start.
2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Click Tools Lexmark Wireless Setup Utility.
4 Follow the instructions on the computer screen.
When the Wi-Fi indicator light is blinking orange, it indicates that the printer has been set up for wireless networking but cannot connect to the network for which it has been configured. The printer may be unable to join the network because of interference, its distance from the wireless access point (wireless router), or until its settings are changed.
These are possible solutions. Try one or more of the following:
Check the wireless access point and, if necessary, turn it on.
There may be temporary interference from other devices such as microwave ovens or other appliances, cordless phones, baby monitors, and security system cameras. Make sure the wireless access point is not positioned too closely to these devices.
Antennas usually work best if they are pointing straight up. You may find that reception improves if you experiment with different angles for the printer and/or wireless access point antennas.
Troubleshooting

Move the printer closer to the wireless access point. Although the possible distance between devices in 802.11b or 802.11g networks is 300 feet, the effective range for optimal performance is generally 100–150 feet.
You can find the signal strength of the network on the network setup page.
A valid WEP key is:
or • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard.
A valid WPA passphrase is:
or • Exactly 64 hexadecimal characters. Hexadecimal characters are A-F, a-f, and 0-9.
If your wireless network is not using security, then you will not have a WEP key or WPA passphrase. Using a wireless network with no security is not recommended because it can allow intruders to use your network resources without your consent.
If your network uses MAC address filtering, make sure that you include the MAC address of the printer in the MAC address filter list. This will allow the printer to operate on the network.
1 Check the AirPort status and, if you do not already know it, find the IP address of the wireless access point.
System Preferences. b Click Network.
a From the menu bar, click
c Click AirPort.
Check Status. It should be on. If it is off, click Turn AirPort On. The AirPort status indicator should also be green. Green means the port is active (turned on) and connected.
Troubleshooting

e Click TCP/IP.
System Preferences. b Click Network.
c If necessary, select Network Status in the Show pop-up menu.
The AirPort status indicator should be green. Green means the port is active (turned on) and connected.
2 Ping the wireless access point. a From the menu bar, click Go Utilities. b Double-click Network Utility.
c Click the Ping tab. d Type the IP address of the wireless access point in the network address field. For example:
10.168.0.100
e Click Ping.
3 If the wireless access point responds, you will see several lines that display the number of bytes received from the access point. This ensures that your computer is connected to the access point.
If the wireless access point does not respond, nothing is displayed. You can use Network Diagnostics to help resolve the problem.
1 From the Finder desktop, double-click the printer folder.
2 Double-click Lexmark Wireless Setup Assistant.
3 Follow the instructions on the computer screen.
When the Wi-Fi indicator light is orange, it may indicate that the printer is:
a Click · Troubleshooting

The printer may be unable to join the network because of interference, its distance from the wireless access point (wireless router), or until its settings are changed.
These are possible solutions. Try one or more of the following:
Make sure your network does not have the same name as another network near you. For example, if you and your neighbor both use a manufacturer's default network name, your printer could be connecting to your neighbor's network.
If you are not using a unique network name, consult the documentation for your wireless access point (wireless router) to learn how to set a network name.
If you set a new network name, you must reset the printer and computer SSID to the same network name.
A valid WEP key is:
or • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard.
A valid WPA passphrase is:
or • Exactly 64 hexadecimal characters. Hexadecimal characters are A-F, a-f, and 0-9.
If your wireless network is not using security, then you will not have a security key. Using a wireless network with no security is not recommended because it can allow intruders to use your network resources without your consent.
Move the printer closer to the wireless access point (wireless router). Although the possible distance between devices in 802.11b or 802.11g networks is 300 feet, the maximum range for optimal performance is generally 100-150 feet.
You can find the strength of the network signal on the printer network setup page.
If your network uses MAC address filtering, make sure that you include the MAC address of the printer in the MAC address filter list. This will allow the printer to operate on the network. For more information, see “How do I find the MAC address?” on page 51.
Troubleshooting

You may see a message during installation indicating that the printer does not have a wireless print server installed. If you are sure the printer is capable of wireless printing, try the following:
Make sure the light is on.
If you are using a laptop and have power saving settings enabled, you may see the Communication not available message on your computer screen when you attempt to print wirelessly. This can occur if the laptop hard drive has powered down.
If you see this message, wait a few seconds and then try to print again. The laptop and printer require a few seconds to power up again and reattach to the wireless network.
If you see this message again after you have waited long enough for the printer and the laptop to attach to the network, there may be a problem with your wireless network. Make sure that the laptop and printer have both received IP addresses. For more information on locating IP addresses, refer to “How do I locate IP addresses?” on page 52.
If the printer and/or the laptop does not have an IP address, or if either has an address of 169.254.x.y (where x and y are any two numbers between 0 and 255):
1 Shut down the device that does not have a valid IP address (the laptop, the printer, or both).
2 Turn on the device(s).
3 Check the IP addresses again.
If the laptop and/or printer still does not receive a valid IP address, there is a problem with your wireless network. Make sure your wireless access point (wireless router) is working, and remove any obstacles that could be blocking the wireless signal.
You will lose your connection to a wireless printer on your local network when connected to most Virtual Private Networks (VPNs). Most VPNs allow users to communicate with only the VPN and no other network at the same time. If you would like to have the ability to connect to your local network and to a VPN at the same time, the system support person for the VPN must enable split tunneling. Be aware that some organizations will not allow split tunneling due to security or technical concerns.
1 From the printer control panel, press .
2 Press the arrow buttons until Network Setup appears, and then press .
Troubleshooting

3 Press the arrow buttons until Reset Network Adapter Defaults appears, and then press .
4 Press the arrow buttons until Yes appears, and then press .
The internal wireless print server is reset to factory default settings. To verify, print a network setup page.
Troubleshooting

Product name:
Machine type:
Model(s):
Product name:
Machine type:
Model number 2:
Edition notice
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.

If you don't have access to the Internet, you can contact Lexmark by mail:
Lexmark International, Inc. Bldg 004-2/CSC 740 New Circle Road NW Lexington, KY 40550 USA
© 2008 Lexmark International, Inc.
All rights reserved.
This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
evercolor and PerfectFinish are trademarks of Lexmark International, Inc.
All other trademarks are the property of their respective owners.
The following document can be viewed from the \Drivers\XPS directory on the installation software CD: Zopen.PDF.
information statement
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232–3000
The following notice is applicable if your printer has a wireless network card installed.
The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
The following notices are applicable if your printer has a wireless network card installed.
This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.

The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb
The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.
Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement.
Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada.
En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.
Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur et loin des fenêtres afin de garantir une protection optimale.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc-sc.gc.ca/rpb
Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme aux spécifications techniques d'Industry Canada.
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC and 2005/32/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and the ecodesign of energy-using products.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
The following notices are applicable if your printer has a wireless network card installed
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment.

Compliance is indicated by the CE marking.
The Alert sign indicates that there are restrictions within certain member states.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
The following restrictions apply:
All countries/regions This product is for indoor use only. This product may not be used outdoors.
L'Italia Si fa presente inoltre che l'uso degli apparati in esame è regolamentato da:
This product satisfies the limits of EN 55022; safety requirements of EN 60950; radio spectrum requirements of ETSI EN 300 328; and the EMC requirements of EN 55024, ETSI EN 301 489-1 and ETSI EN 301 489-17.
Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.
Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.
Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.
Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Country/region Restriction

Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.
Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.
Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.
Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky príslušné ustanovenia smernice 1999/5/ES.
Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Values are subject to change. See www.lexmark.com for current values.

The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products. If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.
Ambient temperature 15–32° C (60–90° F)
Shipping temperature -40–60° C (-40–140° F)
Storage temperature 1–60° C (34–140° F)
Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
The following table documents the power consumption characteristics of the product.

Mode Description Power consumption (Watts)
Printing The product is generating hard-copy output from electronic inputs.
Copying The product is generating hard-copy output from hard-copy original documents.
Scanning The product is scanning hard-copy documents. Lexmark 3600 Series: 10.7; Lexmark 3600es Series: 9.62; Lexmark 4600 Series: 12.5
Ready The product is waiting for a print job. Lexmark 3600 Series: 9.0; Lexmark 3600es Series: 8.73; Lexmark 4600 Series: 12.0
Power Saver The product is in energy-saving mode. Lexmark 3600 Series: 4.8; Lexmark 3600es Series: 5.27; Lexmark 4600 Series: 6.5
Off The product is plugged into a wall outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.
This product is designed with an energy-saving mode called Power Saver. The Power Saver Mode is equivalent to the EPA Sleep Mode. The Power Saver Mode saves energy by lowering power consumption during extended periods of inactivity. The Power Saver Mode is automatically engaged after this product is not used for a specified period of time, called the Power Saver Timeout.
Factory default Power Saver Timeout for this product (in minutes): 60
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the wall outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
PLEASE READ CAREFULLY: BY USING THIS PRODUCT, YOU AGREE TO BE BOUND BY ALL THE TERMS AND CONDITIONS OF THESE LICENSE AGREEMENTS. IF YOU DO NOT AGREE WITH THE TERMS OF THESE LICENSE AGREEMENTS, PROMPTLY RETURN THE PRODUCT UNUSED AND REQUEST A REFUND OF THE AMOUNT YOU PAID. IF YOU ARE INSTALLING THIS PRODUCT FOR USE BY OTHER PARTIES, YOU AGREE TO INFORM THE USERS THAT USE OF THE PRODUCT INDICATES ACCEPTANCE OF THESE TERMS.

I agree that the patented print cartridge(s) shipped with this printing device are sold subject to the following license/agreement: The patented print cartridge(s) contained inside is/are licensed for a single use only and is/are designed to stop working after delivering a fixed amount of ink. A variable amount of ink will remain in the cartridge when replacement is required. After this single use, the license to use the print cartridge terminates, and the used cartridge must be returned only to Lexmark for remanufacturing, refilling or recycling. If I buy another cartridge in the future that is sold subject to the above terms, I accept such terms as to that cartridge. If you do not accept the terms of this single use license/agreement; return this product in its original packaging to your point of purchase. A replacement cartridge sold without these terms is available at www.lexmark.com
This Software License Agreement (“License Agreement”) is a legal agreement between you (either an individual or a single entity) and Lexmark International, Inc. (“Lexmark”) that, to the extent your Lexmark product or Software Program is not otherwise subject to a written software license agreement between you and Lexmark or its suppliers, governs your use of any Software Program installed on or provided by Lexmark for use in connection with your Lexmark product. The term “Software Program” includes machine-readable instructions, audio/visual content (such as images and recordings), and associated media, printed materials and electronic documentation, whether incorporated into, distributed with or for use with your Lexmark product.
1 STATEMENT OF LIMITED WARRANTY. Lexmark warrants that the media (e.g., diskette or compact disk) on which the Software Program (if any) is furnished is free from defects in materials and workmanship under normal use during the warranty period. The warranty period is ninety (90) days and commences on the date the Software Program is delivered to the original end-user. This limited warranty applies only to Software Program media purchased new from Lexmark or an Authorized Lexmark Reseller or Distributor. Lexmark will replace the Software Program should it be determined that the media does not conform to this limited warranty. 2 DISCLAIMER AND LIMITATION OF WARRANTIES. EXCEPT AS PROVIDED IN THIS LICENSE AGREEMENT AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, LEXMARK AND ITS SUPPLIERS PROVIDE THE SOFTWARE PROGRAM "AS IS" AND HEREBY DISCLAIM ALL OTHER WARRANTIES AND CONDITIONS, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, TITLE, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ABSENCE OF VIRUSES, ALL WITH REGARD TO THE SOFTWARE PROGRAM. This Agreement is to be read in conjunction with certain statutory provisions, as that may be in force from time to time, that imply warranties or conditions or impose obligations on Lexmark that cannot be excluded or modified. If any such provisions apply, then to the extent Lexmark is able, Lexmark hereby limits its liability for breach of those provisions to one of the following: replacement of the Software Program or reimbursement of the price paid for the Software Program. 3 LICENSE GRANT. Lexmark grants you the following rights provided you comply with all terms and conditions of this License Agreement:
a Use. You may Use one (1) copy of the Software Program. The term “Use” means storing, loading, installing,
executing, or displaying the Software Program. If Lexmark has licensed the Software Program to you for concurrent use, you must limit the number of authorized users to the number specified in your agreement with Lexmark. You may not separate the components of the Software Program for use on more than one computer. You agree that you will not Use the Software Program, in whole or in part, in any manner that has the effect of overriding, modifying, eliminating, obscuring, altering or de-emphasizing the visual appearance of any trademark, trade name, trade dress or intellectual property notice that appears on any computer display screens normally generated by, or as a result of, the Software Program. b Copying. You may make one (1) copy of the Software Program solely for purposes of backup, archiving, or
installation, provided the copy contains all of the original Software Program’s proprietary notices. You may not copy the Software Program to any public or distributed network.

c Reservation of Rights. The Software Program, including all fonts, is copyrighted and owned by Lexmark International, Inc. and/or its suppliers. Lexmark reserves all rights not expressly granted to you in this License Agreement. d Freeware. Notwithstanding the terms and conditions of this License Agreement, all or any portion of the
Software Program that constitutes software provided under public license by third parties (“Freeware”) is licensed to you subject to the terms and conditions of the software license agreement accompanying such Freeware, whether in the form of a discrete agreement, shrink-wrap license, or electronic license terms at the time of download. Use of the Freeware by you shall be governed entirely by the terms and conditions of such license. 4 TRANSFER. You may transfer the Software Program to another end-user. Any transfer must include all software components, media, printed materials, and this License Agreement and you may not retain copies of the Software Program or components thereof. The transfer may not be an indirect transfer, such as a consignment. Prior to the transfer, the end-user receiving the transferred Software Program must agree to all these License Agreement terms. Upon transfer of the Software Program, your license is automatically terminated. You may not rent, sublicense, or assign the Software Program except to the extent provided in this License Agreement, and any attempt to do so shall be void. 5 UPGRADES. To Use a Software Program identified as an upgrade, you must first be licensed to the original Software Program identified by Lexmark as eligible for the upgrade. After upgrading, you may no longer use the original Software Program that formed the basis for your upgrade eligibility. 6 LIMITATION ON REVERSE ENGINEERING. You may not alter, decrypt, reverse engineer, reverse assemble, reverse compile or otherwise translate the Software Program, except as and to the extent expressly permitted to do so by applicable law for the purposes of inter-operability, error correction, and security testing. If you have such statutory rights, you will notify Lexmark in writing of any intended reverse engineering, reverse assembly, or reverse compilation. You may not decrypt the Software Program unless necessary for the legitimate Use of the Software Program. 7 ADDITIONAL SOFTWARE. This License Agreement applies to updates or supplements to the original Software Program provided by Lexmark unless Lexmark provides other terms along with the update or supplement. 8 LIMITATION OF REMEDIES. To the maximum extent permitted by applicable law, the entire liability of Lexmark, its suppliers, affiliates, and resellers, and your exclusive remedy shall be as follows: Lexmark will provide the express limited warranty described above. If Lexmark does not remedy defective media as warranted, you may terminate your license and your money will be refunded upon the return of all of your copies of the Software Program. 9 LIMITATION OF LIABILITY. To the maximum extent permitted by applicable law, for any claim arising out of Lexmark's limited warranty, or for any other claim whatsoever related to the subject matter of this Agreement, Lexmark's and its suppliers’ liability for all types of damages, regardless of the form of action or basis (including contract, breach, estoppel, negligence, misrepresentation, or tort), shall be limited to the greater of $5,000 or the money paid to Lexmark or its Authorized remarketers for the license hereunder for the Software Program that caused the damages or that is the subject matter of, or is directly related to, the cause of action.
IN NO EVENT WILL LEXMARK, ITS SUPPLIERS, SUBSIDIARIES, OR RESELLERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, EXEMPLARY, PUNITIVE, OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LOST PROFITS OR REVENUES, LOST SAVINGS, INTERRUPTION OF USE OR ANY LOSS OF, INACCURACY IN, OR DAMAGE TO, DATA OR RECORDS, FOR CLAIMS OF THIRD PARTIES, OR DAMAGE TO REAL OR TANGIBLE PROPERTY, FOR LOSS OF PRIVACY ARISING OUT OR IN ANY WAY RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE PROGRAM, OR OTHERWISE IN CONNECTION WITH ANY PROVISION OF THIS LICENSE AGREEMENT), REGARDLESS OF THE NATURE OF THE CLAIM, INCLUDING BUT NOT LIMITED TO BREACH OF WARRANTY OR CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY), AND EVEN IF LEXMARK, OR ITS SUPPLIERS, AFFILIATES, OR REMARKETERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY YOU BASED ON A THIRD-PARTY CLAIM, EXCEPT TO THE EXTENT THIS EXCLUSION OF DAMAGES IS DETERMINED LEGALLY INVALID. THE FOREGOING LIMITATIONS APPLY EVEN IF THE ABOVE-STATED REMEDIES FAIL OF THEIR ESSENTIAL PURPOSE.

10 TERM. This License Agreement is effective unless terminated or rejected. You may reject or terminate this license at any time by destroying all copies of the Software Program, together with all modifications, documentation, and merged portions in any form, or as otherwise described herein. Lexmark may terminate your license upon notice if you fail to comply with any of the terms of this License Agreement. Upon such termination, you agree to destroy all copies of the Software Program together with all modifications, documentation, and merged portions in any form. 11 TAXES. You agree that you are responsible for payment of any taxes including, without limitation, any goods and services and personal property taxes, resulting from this Agreement or your Use of the Software Program. 12 LIMITATION ON ACTIONS. No action, regardless of form, arising out of this Agreement may be brought by either party more than two years after the cause of action has arisen, except as provided under applicable law. 13 APPLICABLE LAW. This Agreement is governed by the laws of the Commonwealth of Kentucky, United States of America. No choice of law rules in any jurisdiction shall apply. The UN Convention on Contracts for the International Sale of Goods shall not apply. 14 UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The Software Program has been developed entirely at private expense. Rights of the United States Government to use the Software Program is as set forth in this Agreement and as restricted in DFARS 252.227-7014 and in similar FAR provisions (or any equivalent agency regulation or contract clause). 15 CONSENT TO USE OF DATA. You agree that Lexmark, its affiliates, and agents may collect and use information you provide in relation to support services performed with respect to the Software Program and requested by you. Lexmark agrees not to use this information in a form that personally identifies you except to the extent necessary to provide such services. 16 EXPORT RESTRICTIONS. You may not (a) acquire, ship, transfer, or reexport, directly or indirectly, the Software Program or any direct product therefrom, in violation of any applicable export laws or (b) permit the Software Program to be used for any purpose prohibited by such export laws, including, without limitation, nuclear, chemical, or biological weapons proliferation. 17 AGREEMENT TO CONTRACT ELECTRONICALLY. You and Lexmark agree to form this License Agreement electronically. This means that when you click the “Agree” or “Yes” button on this page or use this product, you acknowledge your agreement to these License Agreement terms and conditions and that you are doing so with the intent to “sign” a contract with Lexmark. 18 CAPACITY AND AUTHORITY TO CONTRACT. You represent that you are of the legal age of majority in the place you sign this License Agreement and, if applicable, you are duly authorized by your employer or principal to enter into this contract. 19 ENTIRE AGREEMENT. This License Agreement (including any addendum or amendment to this License Agreement that is included with the Software Program) is the entire agreement between you and Lexmark relating to the Software Program. Except as otherwise provided for herein, these terms and conditions supersede all prior or contemporaneous oral or written communications, proposals, and representations with respect to the Software Program or any other subject matter covered by this License Agreement (except to the extent such extraneous terms do not conflict with the terms of this License Agreement, any other written agreement signed by you and Lexmark relating to your Use of the Software Program). To the extent any Lexmark policies or programs for support services conflict with the terms of this License Agreement, the terms of this License Agreement shall control.

ad hoc mode A setting for a wireless device that lets it communicate directly with other wireless devices without an access point or router
ad hoc network A wireless network that does not use an access point
AutoIP address An IP address automatically assigned by a network device. If the device is set to use DHCP, but no DHCP server is available, an AutoIP address may be assigned by the device.
BSS (Basic Service Set) Basic Service Set describes the type of wireless network that you are using. The BSS type can be one of the following: Infrastructure network or Ad-Hoc network.
channel A specific radio frequency used by two or more wireless devices to communicate with each other. All devices on the network must use the same channel.
DHCP (Dynamic Host Configuration Protocol)
A language used by DHCP servers
DHCP IP address An IP address automatically assigned by a DHCP server
DHCP server A computer or router that gives a unique IP address to each device on the network. Unique addresses prevent conflicts.
infrastructure mode A setting for a wireless device that lets it communicate directly with other wireless devices using an access point or router
installation cable Connects the printer to the computer temporarily during some methods of installation.
internal wireless print server A device that lets computers and printers talk to each other over a network without cables
IP (Internet Protocol) address The network address of a computer or printer. Each device on the network has its own network address. The address may be assigned manually by you (Static IP address), automatically by the DHCP server (DHCP IP address), or automatically by the device (AutoIP address).
ipconfig A command that displays the IP address and other network information of a Windows computer
MAC (Media Access Control) address A hardware address that uniquely identifies each device on a network. You can usually find the MAC address printed on the device.
MAC filtering A method of limiting access to your wireless network by specifying which MAC addresses may communicate on the network. This setting may be specified on wireless routers or access points.
network adapter/card A device that lets computers or printers talk to each other over a network
network hub A device that connects multiple devices on a wired network
network name See “SSID (Service Set Identifier)” on page 138
ping A test to see if your computer can communicate with another device
printer nickname The name you assign to your printer so that you and others can identify it on the network
Networking glossary

router A device that shares a single Internet connection with multiple computers or other devices. The basic router controls network traffic.
security key A password, such as a WEP key or a WPA pass phrase, used to make a network secure
signal strength Measure of how strongly a transmitted signal is being received
SSID (Service Set Identifier) The name of a wireless network. When you connect a printer to a wireless network, the printer needs to use the same SSID as the network. Also referred to as network name or BSS (Basic Service Set).
Static IP address An IP address assigned manually by you
switch A device similar to a network hub that can connect different networks together
UAA (Universally Administered Address)
An address assigned to a network printer or print server by the manufacturer. To find the UAA, print a network setup page and look for the UAA listing.
USB cable A lightweight, flexible cable that lets the printer communicate with the computer at much higher speeds than parallel cables
USB port A small, rectangular port on the back of the computer that connects the peripheral devices using a USB cable, and lets them communicate at high speeds
WEP (Wired Equivalent Privacy) A security setting that helps prevent unauthorized access to a wireless network. Other possible security settings are WPA and WPA2.
wireless access point A device that connects wireless devices together to form a wireless network
wireless router A router that also serves as a wireless access point
Wi-Fi An industry term that describes the technology used to create an interoperable wireless local area network (WLAN).
WPA (Wi-Fi Protected Access) A security setting that helps prevent unauthorized access to a wireless network. WPA is not supported on ad hoc wireless networks. Other possible security settings are WEP and WPA2.
WPA2 A newer version of WPA. Older routers are less likely to support this. Other possible security settings are WPA and WEP.
Networking glossary




Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.