
User's Guide
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. All other trademarks are the property of their respective owners.
© 2014 Lexmark International, Inc. All rights reserved. 740 West New Circle Road Lexington, Kentucky 40550


Connect the power supply cord to a properly grounded electrical outlet that is near the product and easily accessible.
CAUTION—POTENTIAL INJURY: Do not twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If the power cord is misused, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of misuse. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a professional service person.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific Lexmark components. The safety features of some parts may not always be obvious. Lexmark is not responsible for the use of other replacement parts.
Safety information 6

Learning about the printer 7
Printer overview
The LexmarkTM Forms Printer 2500 Series printers are available in 9‑ and 24‑wire narrow‑ and wide‑carriage models. Depending on the model you have chosen, your printer may look slightly different from the printer illustrated.

4 5 6 7


Learning about the printer 8


The Lexmark Forms Printer 2500 Series printers have control panel overlays available in different languages.
To apply an overlay in the language of your choice:
1 Peel the backing off of the layer 1 label, and then place the overlay directly over layer 1 of the control panel.
2 Open the control panel cover to access layer 2.
3 Peel the backing off of the layer 2 label, and then place the overlay directly over layer 2 of the control panel.
4 Close the control panel cover.

Learning about the printer 9

Learning about the printer 10

Learning about the printer 11
The following steps explain how to load a single sheet of paper so you can print a demonstration page.
1 Set the forms thickness lever to position 1.
2 Turn the printer on.
The Power light comes on solid, the Paper Out light is blinking, and the current default font light is on solid.

Learning about the printer 12
3 Open the manual feeder, and then move the paper select lever to the position.

4 Move the left paper guide to the right until it stops.
5 Insert a single sheet of paper into the front of the printer.
6 Adjust the right paper guide to fit the paper width.

8 Turn the printer off.
9 While pressing Font on the control panel, turn the printer on.
Hold down the Font button until all the control panel lights blink.
10 Release the Font button.
The Power and Ready lights stay on, and the demonstration page prints.
If the printer is attached to a network, print a network setup page to verify the network connection and find the printer address.

Learning about the printer 13
1 Make sure the printer is on and paper is loaded.
2 With a paper clip or the tip of a pen, press the recessed button located just above the Network connection.

The network setup page prints.
3 Check the first section on the network setup page, and confirm that the status is Connected.
If the status is Not Connected, the LAN drop may not be active, or the network cable may be malfunctioning. Consult a system support person for a solution, and then print another network setup page.
4 Check the network setup page to find the IP Address and the Fully Qualified Domain Name.
The Fully Qualified Domain Name is useful in situations where the Address changes. For instance, the Address changes if the printer is moved; however, the Fully Qualified Domain Name does not change.
When printing from a Windows application, use the Windows Forms Printer 2500 Series driver available from the Lexmark Web site at www.lexmark.com.
Follow the instructions that came with your DOS application to see what printer drivers are supported for your level of DOS. Most applications let you specify the type of printer you are using so the application can take full advantage of the printer features.
If the printer is using IBM mode (the factory default setting), select a printer from your program in the following preferred order.

Learning about the printer 14
1 Forms Printer 2580/2581
2 Forms Printer 2480/2481 plus
3 Forms Printer 2380/2381 plus
4 2380 plus/2381 plus
5 2380/2381 IBM Personal Printer SeriesTM II
6 4201/4202 IBM ProprinterTM III
7 4201/4202 IBM Proprinter II
8 IBM ExecJetTM Printer Model 4072
1 Forms Printer 2590/2591
2 Forms Printer 2490/2491
3 Forms Printer 2390 plus/2391 plus
4 2390 plus/2391 plus
5 2390/2391 IBM Personal Printer Series II
6 4212 IBM Proprinter 24P
7 2390 IBM PS/1 Printer
8 4207/4208 Proprinter X24/XL24
9 IBM ExecJet Printer Model 4072
10 2205 IBM PS/1 Printer
If your software does not allow you to select one of the printers in this list, you may need to customize your printer for Epson emulation mode.
If the printer is using Epson mode, select a printer from your application in the following preferred order.
2 Epson FX 1050
1 Epson FX850

Learning about the printer 15
2 LQ 1050
Using Okidata MICROLINE emulation mode
If the printer has the Okidata MICROLINE emulation option installed, select a printer from your application in the following preferred order.
1 Oki 320/321 Turbo
1 Epson LQ850 · 2 Oki 320/321

Using the control panel 16
Understanding the control panel buttons
The control panel has two layers of functionality:

2 FormFeed Advances the paper to the next Top‑Of‑Form
3 Tractor Alternates between Tractor 1 and Tractor 2 if the optional Tractor 2 is installed
4 Load/Unload Loads paper to the current Top‑Of‑Form or unloads paper to a parked position
5 Font Selects one of the resident font styles
6 Tear Off Alternates the paper between Tear Off and Top‑Of‑Form
7 Start/Stop Communicates the on/off status of the printer

Using the control panel 17
1 2 3 4
Set TOF LineFeed Macro
1 LineFeed Advances the paper one line. Press and hold LineFeed to advance the paper 5 micro movements, and
then go into continuous feed.
2 Macro To support different styles of pre‑printed forms, selects between four document formats
3 Setup Press to enter Setup mode. Lets you change the default values and modes of printer operation.
4 Micro Feeds the paper downward in small incremental movements. Press and hold to select continuous feed.
5 Pitch Sets the character pitch to: 10 cpi, 12 cpi, 15 cpi, 17 cpi, 20 cpi, or proportional spacing
6 Micro Feeds the paper upward in small incremental movements. Press and hold to select continuous feed.
7 Set TOF Sets the Top‑Of‑Form, which is the position of the first print line on the page
The following tables describe the light patterns on the control panel.

Using the control panel 18

Ready On The printer is online and ready to print.
Paper Out Off Paper is loaded in the printer.
On The control panel is locked, restricting the use of the following buttons: Start/Stop, FormFeed, Tear Off, and Load/Unload.
Font On One of the printer resident fonts is selected.
Font Lock On Font Lock is active. Printer resident fonts are locked.
Off No macro is being used, or Macros are disabled in the Setup menu.
Pitch On One of the printer resident pitches is selected.
Pitch Lock On Pitch Lock is active. Printer resident fonts are locked.
The printer must be online to accept data.
The Ready light comes on. If paper is not loaded, the Paper Out light blinks. When online, the printer is ready to receive print jobs. • To set the printer offline, press Start/Stop.
The Ready light turns off. The printer finishes printing the current line and then stops. To resume printing, press Start/Stop until the Ready light comes on.
Use these control panel buttons to advance the paper when the printer is not printing:

Using the control panel 19
To change the Tear Off position on the current page:
Use the Load/Unload button to unload continuous forms from the printer to allow printing on either a cut form or an envelope.
The Load/Unload function works only when the tractor unit is in the push position.
You can also use the Load/Unload button to load continuous forms into the printer when the paper path is clear, or to change one type of pre‑printed form to another.
To restrict the use of printer functions to the Start/Stop, FormFeed, Tear Off, and Load/Unload buttons, lock the control panel. When the panel is locked, the light comes on.
To lock the control panel:
1 Turn the printer off.
2 Press and hold Load/Unload and Tractor while turning the printer on.
To unlock the control panel:
1 Turn the printer off.
2 Press and hold Load/Unload and Tractor while turning the printer on.
When the optional Tractor 2 Feeder is installed, you can press Tractor to unload the current continuous forms and switch to the continuous forms loaded in the other tractor source.
The Tractor 2 light comes on when the optional Tractor 2 Feeder is selected.

Using the control panel 20
The printer data stream may contain control codes which select a particular font. To override the codes, you can select and lock a particular font of your choice.
1 To select a font, press Font repeatedly until you see the font light on next to the selection you want.
Power Ready Tractor 2 Paper Out
Tear Off Load/Unload Tractor
2 Continue pressing Font until the Font Lock light comes on, and the font you want is selected.
The font is locked until the printer is turned off.
1 To disable Font Lock, press Font repeatedly until the Font Lock light turns off and the font you want is selected.
2 If the printer is offline, press Start/Stop.
The printer is ready to print when the Ready light comes on.

Using the control panel 21
The printer data stream may contain control codes which select a particular pitch. To override the codes, you can select and lock a particular pitch of your choice.
1 To select a pitch, open the control panel to layer 2.
1 2 3 4
Set TOF LineFeed Macro
2 Press Pitch repeatedly until the pitch light comes on next to the pitch you want.
3 Continue pressing Pitch until the Pitch Lock light comes on and the pitch you want is selected.
The pitch is locked until the printer is turned off.
1 To disable Pitch Lock, press Pitch repeatedly until the Pitch Lock light turns off and the pitch you want is selected.
2 Close the control panel.
3 If the printer is offline, press Start/Stop.
When the Ready light comes on, the printer is ready to print.

This section explains how to load continuous forms, cut sheet forms, labels and envelopes. It also includes information about paper orientation, setting the forms thickness lever, and using the push and pull tractors for different paper paths.

1 Cut sheet forms
Use the forms thickness lever to make adjustments for printing on various forms depending on the paper thickness. When setting this lever, see one of the following tables depending on your printer model:


Paper type Paper thickness Paper weight Forms thickness lever setting
Single forms (cut or continuous) Thin 56 g/m2 (15 lb)
65 g/m2 (16 lb)
Normal 68 g/m2 (18 lb)
75 g/m2 (20 lb)
Thick 90 g/m2 (24 lb) 2
Multiple‑part forms 2‑part 3‑part
2 or 3 3 or 4
5, 6, or 7
Envelopes 4, 5, or 6
Paper type Paper thickness Paper weight Forms thickness lever setting
Single forms (cut or continuous) Thin 56 g/m2 (15 lb)
65 g/m2 (16 lb)
Normal 68 g/m2 (18 lb)
75 g/m2 (20 lb)
Thick 90 g/m2 (24 lb) 2
Multiple‑part forms 2‑part
5, 6, or 7
Envelopes 4, 5, or 6
Print quality depends on the multiple‑paper quality and the operating environment. Low‑temperature printing may cause poor print quality, depending on the paper used.
In these examples, the tractor pushes the paper from the front or the rear of the printer.


In these examples, the tractor pulls the paper from the front or the bottom of the printer.

Pressing the Tear Off button advances the perforation of a continuous form to the tear off position. You can set the Tear Off function to automatic or manual by adjusting the Auto Tear Off Setting in Setup mode:
When Auto Tear Off is set to On, it moves the top perforation of a continuous form to the Tear Off position when all of the following are true:
Loading paper 24

If you have already set your Top‑Of‑Form and now want to change the Tear Off position, follow these steps:
1 Press Start/Stop to take the printer offline.
2 Press and hold Tear Off until the printer beeps.
The light blinks.
3 Open the control panel cover to access layer 2.
4 Press Micro or Micro to move the paper to the desired Tear Off position.
5 Close the control panel cover.
The printer beeps twice. The paper rolls backward, then goes to the new Tear Off position.
6 Press Start/Stop.
The paper remains at the current Tear Off position until you send another job to the printer. The paper moves from the Tear Off position to the Top‑Of‑Form and begins printing.
You can load continuous paper utilizing four different paper paths, depending on whether you have the push tractor installed or the pull tractor installed. The factory default setting for your printer is the push tractor position.
1 Turn the printer on.

2 Make sure the paper path is clear.
Loading paper 25

3 Set the forms thickness lever to a setting corresponding with the paper thickness you are using.

4 Pull the front cover up.

5 Move the paper select lever down to the position.
6 Pull the left and right tractor locking levers up to unlock the tractors.

Loading paper 26

7 Open the left and right tractor doors, and then place the paper holes over the second or third pins of the tractor unit.

If necessary, move the left or right tractor to adjust the tractors to the paper width.
8 Close the left and right tractor doors.

9 Move the tractor to align the left margin on your paper with the [A symbol printed on the rear plate.
10 Push the left tractor locking lever down to lock the tractor in place.
11 Remove slack from the paper, and then lock the right locking lever.
Loading paper 27

12 Close the front cover.

13 Press Start/Stop to load the paper to Top‑Of‑Form and put the printer online.
If Auto Tear Off is set to On, the printer moves the paper to the Tear Off bar.
Make sure the tractor is in the pull position.
1 Turn the printer on.
2 Make sure the paper path is clear.
3 Set the forms thickness lever to a setting corresponding with the paper thickness you are using.

4 Remove the ribbon access cover.
5 Move the paper select lever down to the position.
Loading paper 28

6 Pull the left and right tractor locking levers up to unlock the tractors.

7 Open the left and right tractor doors.

8 Open the front cover.
9 Insert paper into the front of the printer between the metal and plastic plates.
Loading paper 29

Push or pull the paper through the paper path until it passes the printhead.

10 Close the front cover.

11 Place the paper holes over the tractor pins.
If necessary, move the left or right tractor to adjust the tractors to the paper width.
12 Close the left and right tractor doors.
13 Replace the ribbon access cover.
14 Move the tractor to align the left margin on the paper with the [A symbol printed on the rear plate.
15 Push the left tractor locking lever down to lock the tractor in place.
Loading paper 30

16 Remove slack from the paper, and then lock the right locking lever.

17 Open the control panel cover to access layer 2.
18 Press Micro, Micro, or LineFeed to move the paper to the Top‑Of‑Form you want to use.
19 Press Set TOF to set the Top‑Of‑Form.
20 Make sure the printer is online, and the Ready light is on solid.
Loading paper 31

1 Turn the printer on.

2 Make sure the paper path is clear.
3 Set the forms thickness lever to 7.

4 Move the paper select lever down to the position.
Loading paper 32

5 Remove the ribbon access cover.

6 Pull the left and right tractor locking levers up to unlock the tractors.

Loading paper 33

7 Open the left and right tractor doors.

8 Insert the paper through the bottom slot of the printer.
Push or pull the paper through the paper path until it passes the printhead.
9 Place the paper holes over the tractor pins.

Loading paper 34

If necessary, move the left or right tractor to adjust the tractors to the paper width.
10 Close the left and right tractor doors.
11 Replace the ribbon access cover.
12 Move the tractor to align the left margin on the paper with the [A symbol printed on the rear plate.

13 Push the left tractor locking lever down to lock the tractor in place.
14 Remove slack from the paper, and then lock the right locking lever.
15 Open the control panel cover to access layer 2.
16 Press Micro , Micro , or LineFeed to move the paper to the Top‑Of‑Form you want to use.
17 Press Set TOF to set the Top‑Of‑Form.
18 Make sure the printer is online, and the Ready light is on solid.
Loading paper 35

Cut forms can be single sheets, envelopes, or multiple-part forms. They are placed one at a time into the manual feeder.
1 Turn the printer on.

2 Make sure the paper path is clear.
3 If continuous forms are currently loaded, tear off the leading edge of the continuous form, and then press Load/Unload to park the continuous forms.
The Paper Out light blinks.
4 Set the forms thickness lever to a corresponding setting for the type of paper you are using.
5 Move the paper select lever up to the position.

6 Open the manual feeder.
Loading paper 36

7 Move the left paper guide so that the print start position you want aligns with the [A symbol printed on the margin guide.
The distance from the left paper guide to the [A symbol determines the width of the left margin.

8 Place a cut form or an envelope against the left paper guide.
9 Move the right paper guide so the guide aligns with the right edge of the cut form or envelope.

1 Left paper guide
2 Cut form or envelope
3 Right paper guide
10 Insert the cut form or envelope into the printer until the Paper Out light stops blinking.
Loading paper 37

11 Make sure the printer is online, and the Ready light is on solid.
You can manually change the first print position at the left margin. The first print position is indicated by the [A symbol. You can also set the left margin in your program.
1 Locate the left margin for continuous forms by locating the [A symbol on the printer.

1 Tractor (in push position)
2 Right locking lever
2 Continue to load paper utilizing different paper paths, depending on whether you have the push tractor installed or the pull tractor installed. For help, see one of the following sections in this chapter:
Loading paper 38

Top-of-Form sets the first line of print. Use the control panel to save your Top-of-Form settings for continuous forms, cut forms, and for each macro enabled.
1 Clear the paper path.
The Paper Out light blinks if no paper is loaded. If the Paper Out light is off, tear off excess forms, and then press Load/Unload. If a cut form is loaded, press FormFeed to clear the paper path.
2 Make sure the paper select lever is in the position.
3 Load continuous form paper on the push tractor feed pins (or the Tractor 2 feed pins if you are using the optional Tractor 2 Feeder).
4 Press FormFeed.
The paper moves to the current Top‑Of‑Form, and the Paper Out light goes off.
5 Open the control panel cover to access layer 2.
1 2 3 4
Set TOF LineFeed Macro
6 Press any paper movement button (LineFeed, Micro, Micro ) to align the horizontal lines located on the platen with the Top‑Of‑Form you want.
7 Press Set TOF to set and save your Top‑Of‑Form.
8 Close the control panel cover.
9 To verify the new Top‑Of‑Form, press Load/Unload to unload the continuous forms paper, and then press FormFeed to reload the continuous forms paper.
The continuous forms paper loads to the current Top‑Of‑Form setting.
10 Press Start/Stop to set the printer online.

1 Turn the printer on.
The Paper Out light blinks if no paper is loaded.
2 Move the paper select lever down to the position.
3 Load continuous form paper on the pull tractor feed pins.
4 Open the control panel cover to access layer 2.

5 Press any paper movement button (Micro, Micro, or LineFeed) to move the paper to the Top‑Of‑Form position.
6 Press Set TOF to set and save Top‑Of‑Form.
7 Close the control panel cover.
8 Press Start/Stop to set the printer online.
Setting Top‑Of‑Form for a cut form or an envelope
Top‑Of‑Form can range from minus one inch to plus 22 inches from the top of a cut form.
1 Clear the paper path.
The Paper Out light blinks if no paper is loaded. If the Paper Out light is off, tear off excess forms, and then press Load/Unload. If a single form is loaded, press FormFeed to clear the paper path.
2 Move the paper select lever up to the position.
Loading paper 40

4 Open the control panel cover to access layer 2.

5 Press any paper movement button (Micro, Micro, LineFeed) to align the horizontal lines located on the platen with the Top‑Of‑Form you want.
6 Press Set TOF to set and save your Top‑Of‑Form.
7 Close the control panel cover.
8 Press Start/Stop to put the printer online.
Each macro has a separate Top‑Of‑Form setting. To set Top‑Of‑Form in a macro, you must first select that macro.
1 Open the control panel cover to access layer 2.
2 Press Macro to select the macro you want to use.
Loading paper 41

Paper and specialty media guide 42
Paper types and sizes supported by the printer
The printer supports paper weights of 56–90 g/m2 (15‑24 lb) and envelope weights of 75–90 g/m2 (20‑24 lb).
Paper types Single Multiple part Envelopes
Cut Forms 76 mm (3.0 in.) to 297 mm (11.7 in.)*
76 mm (3.0 in.) to 297 mm (11.7 in.)*
152 mm (6.0 in.) to 241 mm (9.5 in.)
Continuous Forms 76 mm (3.0 in.) to 254 mm (10.0 in.)
76 mm (3.0 in.) to 254 mm (10.0 in.)
Hole‑to‑hole widths 63 mm (2.5 in.) to 241 mm (9.5 in.)
63 mm (2.5 in.) to 241 mm (9.5 in.)
* When the optional Auto Sheet Feeder or the Tractor 2 Feeder is installed, the cut form maximum width is 215 mm (8.5 in.) for manual loading.
Paper types Single Multiple part Envelopes
Cut Forms 76 mm (3.0 in.) to 559 mm (22.0 in.)
76 mm (3.0 in.) to 559 mm (22.0 in.) 110 mm (4.1 in.) to 152 mm (6.0 in.)
Continuous Forms 76 mm (3.0 in.) (no maximum) 76 mm (3.0 in.) (no maximum) Not applicable
Paper types Single Multiple part Envelopes
Cut Forms 0.058 mm (0.0023 in.) to 0.114 mm (0.0045 in.) See the following note. 0.42 mm (0.017 in.)
Continuous Forms 0.058 mm (0.0023 in.) to 0.114 mm (0.0045 in.) See the following note. 0.42 mm (0.017 in.)
Not applicable · Not applicable

Changing tractor positions 43
The tractor unit can be installed in the push tractor position or the pull tractor position. This section describes how to change the tractor unit position.
The printer comes with the tractor unit installed in the push tractor position, at the front of the printer. Using the front push tractor is the most convenient way to load continuous forms, and allows you to use the Tear Off feature of the printer.

The front tractor unit can be removed and installed at the top of the printer. It then functions as a pull tractor and supports front and bottom paper loading.


Changing tractor positions 44
1 Make sure the printer is off.
2 Make sure paper is not loaded in the printer.
3 Pull the front cover up and out of the way.
4 Hold down the latching levers while you lift and pull the tractor unit out of the printer.

5 Remove the ribbon access cover.
6 Turn the tractor unit around so that the latching levers are upright, facing you.
7 Place the tractor against the back slant of the printer along the tractor guides.

1 Tractor unit · 2 Latching levers

Changing tractor positions 45
8 To slide the tractor feeder into the printer: a Hold down the latching levers and gently push the tractor feeder into the printer until it stops. b Continue holding down the latching levers, and tilt the tractor feeder toward the front of the printer until the
hooks at the end of the latching levers fit around the posts on the printer frame.

c Release the latching levers.
1 Make sure the printer is off.
2 Make sure paper is not loaded in the printer.
3 Hold down the latching levers while you lift and pull the tractor unit out of the printer.

4 Pull the front cover up and out of the way.

Changing tractor positions 46
5 Make sure the paper select lever is set to the position.

6 While holding down the latching levers, fit the left and right locks onto the posts in the printer.

7 Release the latching levers.
8 Close the front cover.

Understanding Setup mode and menu options 47
The printer is preset at the factory for font, pitch, form length, and other settings. These are called factory default settings. This chapter describes how to change the factory default settings, how to set up macros, and how to set form length.
1 Open the control panel to access layer 2.

2 Press Setup to put the printer in Setup mode and print the Main menu.
3 Press LineFeed to print a list of available options you can change.
Exit and Save Setup Set TOF
Forms Macro Options Macro
To Select Press · Print All LineFeed

Understanding Setup mode and menu options 48
4 Select any option from the Main menu by pressing the corresponding button.
5 After you make all your selections, the printer will print a page with your changes reflected.
6 Press Set TOF until the printer returns to the Main menu, or press Pitch from any menu containing a Return to Main menu selection.
7 Press Set TOF again to exit Setup mode.
New settings are saved only when the printer exits Setup mode.
The following is an example of how to change the Menu Language setting.
1 With the printer in Setup mode, press Micro to print the Control Options menu.
2 Press Pitch to print more Control Options.

3 To change the Menu Language, press Macro.


Understanding Setup mode and menu options 49
Control Options Current Press
4 Press the button that corresponds to the language you want, or press Setup to print more Menu Language options.
5 For this example, press Macro to select French.
No Change Set TOF
Return to Main menu Pitch
Printer menus now print in French.
6 Press Pitch to return to the Main menu or press Set TOF (No Change) to go back one menu and change another setting.
7 If you return to the Main menu, press Set TOF to exit Setup mode and save the new setting.
The following list items will appear at the top of the Main menu page:
Forms Macro Options customizes macros to print a variety of forms.
Data Options defines how information sent to the printer is processed.

Understanding Setup mode and menu options 50
Control Options define how the printer performs many basic tasks.
Emulation Options determine how the printer interacts with the program.
Interface Options define how information is transferred from the computer to the printer.
The following list items outline and explain the Forms Macro functions and settings you can use with the printer:
Default Macro lets you select the macro default you want when the printer is powered on. Select Disabled if you do not want to use a macro as the default.
Use the following options to select character option changes, as detailed:
– Eastern European, Baltic, and Middle Eastern language code page configurations can be selected by holding
down specific key combinations when the printer is turned on. For more information, see the Technical Reference available on the Lexmark Web site at www.lexmark.com. – 437 is the factory default setting. • Character Set—Select Character Set 1 or Character Set 2.

Understanding Setup mode and menu options 51
Use the following options to select paper handling option changes, as detailed:
On—Automatically loads paper if the optional Auto Sheet Feeder is installed.
This option lets you set the form length (in lines per page) from one line to a maximum of 22 inches. • Left Margin
This option lets you set the left margin to any inch increment from 0” to 3”. • Right Margin
This option lets you set the right margin to any inch increment from 4” to 8”. If you have a wide carriage model, the maximum right margin is 13.6”. • Lines Per Inch
Lets you specify the number of text lines in an inch from 3 to 8.
The following list items outline and explain the Data options and settings you can use with the printer:

Understanding Setup mode and menu options 52
Requires a line feed to occur.
Requires a CR to occur.
Code Page Sub.
The following list items outline and explain the Control options and settings you can use with the printer:

Understanding Setup mode and menu options 53
Uni‑Dir Printing
Customizes how the printer goes to the Ready state after a cut sheet is loaded.
Select the language you want the menus to print in. Available languages are: English, French, German, Italian, Spanish, and Brazilian Portuguese.

Understanding Setup mode and menu options 54
Make Emulation option selections from IBM (the factory default setting), Epson, or OKI mode. For more information regarding data stream changes, see the Technical Reference available on the Lexmark Web site at www.lexmark.com/publications.
Proprinter III, available only on 2580/2581 printers, enables compatibility with the Proprinter III.
AGM, available only on 2590/2591 models, lets you use the high‑resolution 24‑wire graphics commands. These commands are similar to those used with the Epson LQ570/LQ 1070.
Supported international character sets for Epson mode are: USA, France, Germany, U.K., Denmark, Sweden, Italy, and Spain I.
The following character sets are also supported, but only through host commands used by Epson FX850/FX 1050: Japan, Norway, Denmark II, Korea (2580/2581 models only), Spain II, Latin America, and Legal.
OKI mode lets you select from the following functions:
The following list items outline and explain the Interface options and settings you can use with the printer:

Understanding Setup mode and menu options 55
Unless turned off, the Auto setting automatically selects the printer interface from the available connection cables.
The following connection cables are available: parallel cable, USB cable, serial cable (only available when an optional serial interface is installed), and network cable (only available on network models).
Honor Init.

Maintaining the printer 56
Periodically, certain tasks are required to maintain optimum print quality.
Use the listed part numbers to order printer supply items you will need.
Supply item Part number
Serial adapter and cable 12T0154 (Serial Interface option)
1038693 (50‑foot cable)
1 Turn the printer off.
2 Lift the left and right release latches on the ribbon access cover to remove it.
3 Place the ribbon access cover on a flat surface.
4 Set the forms thickness lever to position 7.
5 Squeeze the left and right latches on the ribbon cartridge to lift it out of the printer.
1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Squeeze the left and right latches on the ribbon cartridge, and then lift it out of the printer.
Every few months, use a soft brush and a vacuum to remove dust, ribbon lint, and pieces of paper from the printer. Vacuum any dust from around the printhead and from inside the printer.
USB cable 12A2405

Maintaining the printer 57
Clean the outside of the printer with a damp cloth and mild soap. Do not use spray or chemical cleaners anywhere on your printer. Do not use liquids or spray near the air vents. For stubborn ink stains on the outside of the printer, use a commercial mechanic's hand cleaner.
To return Lexmark products to Lexmark for recycling:
1 Visit our Web site at www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country from the list.
3 Follow the instructions on the computer screen.

Restoring the factory default settings
The factory default settings for the United States are:
To restore the factory default settings:
1 Make sure the ribbon cartridge is installed and paper is loaded.
2 Turn the printer off.
3 Open the ribbon access cover.
4 Move the printhead over toward the control panel side of the printer until it stops.
5 Close the ribbon access cover.
6 Press and hold Tear Off and Load/Unload while turning the printer on.
7 Continue holding the buttons until the carrier moves.
The factory default settings have been restored once the carrier moves.
The factory default settings for Europe are:
To restore the factory default settings:
1 Make sure the ribbon cartridge is installed and paper is loaded.
2 Turn the printer off.
3 Open the ribbon access cover.
4 Move the printhead over toward the control panel side of the printer until it stops.
5 Close the ribbon access cover.
6 Press and hold Tear Off and Tractor while turning the printer on.
7 Continue holding the buttons until the carrier moves.
Administrative support 58

The factory default settings have been restored once the carrier moves.
Internet Protocol Security (IPSec) provides authentication and encryption at the network layer allowing all application and network connections over the IP protocol to be secure. IPSec can be set up between the printer and up to five hosts, using both IPv4 and IPv6.
To configure IPSec using the Embedded Web Server:
1 Open a Web browser. In the address bar, type the IP address of the printer or print server to be protected using the format: http://ip_address.
2 Click Configuration.
3 Under Other Settings, click Network/Ports.
4 Click IPSec.
IPSec supports two types of authentication:
Simple Network Management Protocol version 3 (SNMPv3) allows for encrypted and authenticated network connections. It also lets a system support person select the desired level of security. Prior to use, at least one user name and password must be assigned from the settings page.
To configure SNMPv3 through the Embedded Web Server:
1 Open a Web browser. In the address bar, type the IP address of the printer or print server to be protected using the format: http://ip_address/.
2 Click Configuration.
3 Under Other Settings, click Network/Ports.
4 Click SNMP.
SNMPv3 authentication and encryption has three levels of support:
Administrative support 59

802.1x authentication allows the printer to join networks that require authentication before allowing access.
Support for 802.1x requires the establishment of credentials for the printer, such as certificates. Certificates provide a way for the printer to be known to the Authentication Server (AS). The AS allows network access to print servers presenting a valid set of credentials. You can manage the credentials by using the Embedded Web Server.
To install and use certificates as part of the credentials:
1 Open a Web browser. In the address bar, type the IP address of the printer or print server to be protected using the format: http://ip_address/.
2 Click Configuration.
3 Under Other Settings, click Network/Ports.
4 Click Certificate Management.
To enable and configure 802.1x after installing the required certificates:
1 Open a Web browser. In the address bar, type the IP address of the printer or print server to be protected using the format: http://ip_address/.
2 Click Configuration.
3 Under Other Settings, click Network/Ports.
4 Click 802.1x Authentication.
Administrative support 60

Checking an unresponsive printer
If your printer is not responding, make sure:
Once you have checked each of these possibilities, turn the printer off and then back on. This often fixes the problem.
Each time you turn the printer on, an internal check, or power‑on self test, is performed.
Running a printer test page produces a printout that shows any problem the printer may be experiencing.
1 Make sure the paper is loaded, and the ribbon cartridge is installed.
2 Turn the printer off.
3 Press and hold LineFeed while turning the printer on.
4 Release LineFeed when printing starts.
Printing continues until you stop the printer.
To interrupt a printer test page:
1 Press Start/Stop.
The printer test page stops printing after a complete line of characters has printed.
2 Press Start/Stop again to continue printing a printer test page.
To stop a printer test page, turn the printer off.
Troubleshooting 61

Hex Trace mode prints the control codes that are sent to the printer. Use this mode to help diagnose software/driver problems.
1 Make sure the paper is loaded, and the ribbon cartridge is installed.
2 Turn the printer off.
3 Press and hold Tractor while turning the printer on.
4 Release Tractor when the lights go out.
5 Turn the printer off and back on again to exit Hex Trace mode.
Check the control panel lights and compare their status with the table information. Different patterns and combinations of lights provide you with information about the condition of the printer and actions needed to correct the condition.
Control panel lights Status Action required
Normal operating conditions. No action required.
1 Load paper. 2 Press Start/Stop.
The Paper Out light goes off and the Ready light comes on.
Ready Blinking The printer has data in the buffer that needs to be printed.

Control panel lights Status Action required
1 Check for a paper or ribbon jam. 2 Turn the printer off. 3 Remove the ribbon cartridge, and then check for paper dust or bits of paper. 4 Make sure the carrier packing tape has been removed. 5 With the printer on, run the printer test. a Replace the ribbon cartridge, and make sure
paper is loaded. b Turn the printer off.
c Press and hold LineFeed while turning the printer on. d Release LineFeed when printing starts.
Printing continues until the printer is stopped. 6 If the printer test fails, contact Customer Support.
Power Off Check the power cord and power source. If the power light remains off, contact Customer Support.
The paper select lever has been changed while the paper was loaded. Move the paper select lever back to the correct position, and then press Start/Stop.
1 Open and close the control panel. 2 Turn the printer off and back on. 3 If the control panel light sequence continues, contact Customer Support.
Make sure the Tractor 2 option is installed correctly. For more information, see the documentation that came with the option.

Control panel lights Status Action required
1 Turn the printer off. 2 Turn the printer on.
If the control panel light sequence returns, contact Customer Support.
All lights on solid On
Occasionally you may want to adjust the character alignment (also called bidirectional alignment) on your printer. The following steps illustrate how to adjust the alignment of the print wires.
1 Turn the printer off.
2 Open the control panel cover to access layer 2.
3 Press and hold Pitch while turning the printer on.

The draft alignment bars print.

4 To set Draft, select the best row of alignment bars from the 01–07 printout. a Press Micro or Micro to select the best alignment by number, or keep the current value. b Press Set TOF to save your selection.
After you make your selection, the printer prints a single row showing the current alignment setting.

c The printer automatically starts printing the alignment bars for Near‑Letter‑Quality (NLQ).

The current value is the number printed below the bars.
Printer test works, but the printer does not print when attached to the computer
These are possible solutions. Try one or more of the following:
Troubleshooting 65

These are possible solutions. Try one of more of the following:
These are possible solutions. Try one or more of the following:
This might indicate an error or a normal operation. If an error condition is present, these are possible solutions. Try one or more of the following:
Set Auto Tear Off to On:
1 Press Start/Stop.
2 Press and hold Tear Off until the printer beeps and the light blinks.
3 Open the control panel to access layer 2.
4 Press Micro or Micro to move the paper to the desired position.
5 Close the control panel.
The printer beeps twice and the paper rolls backward and then advances to the new Top‑Of‑Form position.
6 Press Start/Stop.
The paper remains at the new Top‑Of‑Form position until another job is initiated.
7 Send the print job again.
Troubleshooting 66

1 Turn the printer off.
2 Press and hold Load/Unload and Tractor while turning the printer on.
When the light goes off, the control panel is unlocked, and all buttons are active.
These are possible solutions. Try one of more of the following:
These are possible solutions. Try one or more of the following:
These are possible solutions. Try one or more of the following:
These are possible solutions. Try one of more of the following:
Printing speed is slower when the forms thickness lever is set at 4 or higher. This is normal. • Select resident fonts.
Troubleshooting 67

These are possible solutions. Try one or more of the following:
site at www.lexmark.com. – If you are using DOS, follow the instructions that came with your DOS application.
These are possible solutions. Try one or more of the following:
If you encounter this problem, your software is overriding your control panel font and/or pitch selection, or using graphic fonts. If possible, use resident fonts and/or pitches. Otherwise, try the following solution:
1 Turn the printer off.
2 Detach any continuous forms that have already printed.
3 Set the forms thickness lever to position 7.
4 Tear the continuous forms off at the perforation line just below the bottom of the printer.
5 Open the front cover.
6 Open the left and right tractor doors, and then remove the paper.
7 Remove the ribbon access cover to clear any torn paper.
8 Remove torn perforation strips or bits of paper from the paper path.
Troubleshooting 68

1 Turn the printer off.
2 Set the forms thickness lever to position 7.
3 Push the paper select lever down to the position.
4 Gently pull the sheet of paper from the front of the printer.
5 Remove the ribbon access cover to clear any torn pieces of paper.
6 Push the paper select lever up to the position.
7 Set the forms thickness lever to the proper setting for the type of paper you are using.
These are possible solutions. Try one or more of the following:
These are possible solutions. Try one or more of the following:
The continuous form on one tractor feeder was not properly parked before switching to the other tractor feeder.
Make sure you tear off the leading edge of the continuous form on the currently selected tractor feeder before switching tractor feeders. For help, see the documentation that came with the optional Tractor 2 Feeder.
These are possible solutions. Try one or more of the following:
Look for loose pinfeed hole strips that can sometimes tear from the continuous forms and remain in the printer. • Readjust the right tractor position.
Troubleshooting 69

These are possible solutions. Try one or more of the following:
These are possible solutions. Try one or more of the following:
The optional Tractor 2 Feeder positions paper at incorrect Top‑Of‑Form position
The Top‑Of‑Form is set incorrectly. For more information about correctly setting Top‑Of‑Form, see “Setting Top-of- Form” on page 39.
These are possible solutions. Try one or more of the following:
Troubleshooting 70

The Auto Sheet Feeder places paper at the wrong Top‑Of‑Form position
These are possible solutions. Try one or more of the following:
These are possible solutions. Try one of more of the following:
These are possible solutions. Try one of more of the following:
Troubleshooting 71

The information in the following topics may help you solve print quality problems. If these suggestions do not correct the problem, contact Customer Support. You may have a printer part that requires adjustment or replacement.
These are possible solutions. Try one or more of the following:
The ribbon density control knob located on the ribbon cartridge is preset to 1. When the print becomes too light, turn the knob from 1 to 2 to increase print darkness.

The forms thickness lever may be set to the wrong number. If so, move it to the correct number for the form thickness you are using.
1 Make sure the ribbon is securely snapped down on the carrier.
2 Adjust the density control knob from 1 to 2 to increase darkness of print.
3 Replace the ribbon cartridge.
4 Run a printer test. a Make sure the paper and the ribbon cartridge are installed. b Turn the printer off.
c Press and hold LineFeed while you turn the printer on, and then release LineFeed when printing begins.
Troubleshooting 72

d Press Start/Stop to stop or interrupt the printer test. e Press Start/Stop again if you want to resume the printer test.
Printing continues until you turn the printer off.
If the print quality does not improve, contact Customer Support.
Run a printer test:
1 Make sure the forms thickness lever setting is in a position that corresponds with the forms you are using.
2 Make sure paper and the ribbon cartridge are installed.
3 Set the paper select lever to the position that corresponds with the forms you are using.
4 Turn the printer off.
5 Press and hold LineFeed while you turn the printer on.
6 Release LineFeed when printing starts.
Printing continues until you stop the printer.
7 Press Start/Stop to stop the printing, and then turn the printer off.
These are possible solutions. Try one or more of the following:
These are possible solutions. Try one or more of the following:
These are possible solutions. Try one or more of the following:
Troubleshooting 73

These are possible solutions. Try one or more of the following:
When you call Customer Support, describe the problem you are experiencing, the message on the display, and the troubleshooting steps you have already taken to find a solution.
You need to know your printer model type and serial number. For more information, see the label on the inside top front cover of the printer. The serial number is also listed on the menu settings page.
In the U.S. or Canada, call (1‑800‑539‑6275). For other countries/regions, visit the Lexmark Web site at www.lexmark.com.
Troubleshooting 74


The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
If you don't have access to the Internet, you can contact Lexmark by mail:
Lexmark International, Inc. Bldg 004-2/CSC 740 New Circle Road NW Lexington, KY 40550
© 2014 Lexmark International, Inc.
All rights reserved.
January 2014

This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.
Lexmark and Lexmark with diamond design, ExecJet, and Proprinter are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
Personal Printer Series is a trademark of Lexmark International, Inc.
ITC Avant Garde Gothic is a trademark or registered trademark of International Typeface Corporation.
All other trademarks are the property of their respective owners.
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232–3000
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
This product is in conformity with the protection requirements of EC Council directives 89/336/EEC and 2006/95/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits.
A declaration of conformity with the requirements of the directives has been signed by the Director of Manufacturing and Technical Support, Lexmark International, Inc., S.A., Boigny, France.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Values are subject to change. See www.lexmark.com for current values.
Printing 56 dBA · Ready NA

The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products. If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
Power consumption
The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs. 47 W
Copying The product is generating hard‑copy output from hard‑copy original documents.
Scanning The product is scanning hard‑copy documents. NA
Ready The product is waiting for a print job. 8 W
Power Saver The product is in energy‑saving mode. NA
High Off The product is plugged into a wall outlet, but the power switch is turned off. NA
Low Off (
the product is in the lowest possible power consumption mode.
Off The product is plugged into a wall outlet, but the power switch is turned off. 0.055 W

The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.
This product is designed with an energy-saving mode called Power Saver. The Power Saver Mode is equivalent to the EPA Sleep Mode. The Power Saver Mode saves energy by lowering power consumption during extended periods of inactivity. The Power Saver Mode is automatically engaged after this product is not used for a specified period of time, called the Power Saver Timeout.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the wall outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
Lexmark 2580 Lexmark 2590
Lexmark 2580n Lexmark 2590n
Lexmark 2581 Lexmark 2591
Lexmark 2581n Lexmark 2591n
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country- specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).

If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 24 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web at www.lexmark.com/support.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH

RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.


paper fed in Auto Sheet Feeder
jams at printer entrance 69 paper jammed in Auto Sheet
Feeder 69 printer does not feed from Auto
Sheet Feeder 70 printer does not feed paper 69 troubleshooting, print
buttons do not work 67 incorrect characters print, left
margin changes, or printing stops 68 left margin moves right during
printing 67 Print test works, but printer does
not print when attached to the computer 65 printer alarm sounds 66 printer is noisy 66 printer power switch is on, but the
power light is off 67 printer sounds like it is printing,
but does not print 66 printer speed slows 67 printing continues beyond edges
of continuous forms 68 troubleshooting, print quality
characters are wrong or
missing 73 dots are missing or print quality is
poor 72 graphics do not print 73 incorrect line length 67 incorrect line spacing or
overprinting occurs 74 incorrect number of lines on a
page 73 lines do not start at left margin 67 print is too light 72 printer goes to Tear Off position
before job finishes 66 smudged forms or print too
dark 73 specified font or pitch is not
printing or is changing 68
Index 84 · printing from 13 · control panel 19
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.