EN
Lexmark logo
Official user manual

Lexmark 230

127 pages·7.8 MB·Printer·PDF·ENDEFRITNLJA
Lexmark 230
Table of Contents 65 sections Contents · Notices · Edition notice · Trademarks · … ShowHide
Contentsp.2Noticesp.6Edition noticep.6Trademarksp.6Licensing noticep.7Safety informationp.7Laser noticep.7The United Kingdom Telecommunications Act 1984p.7Conventionsp.7Electronic emission noticesp.7Printer energy consumptionp.9Statement of Limited Warrantyp.9Printer overviewp.11Print media tasks and tipsp.13What types of print media can be loaded?p.14Where can print media be loaded in the printer?p.15Tips on choosing the right print mediap.16Tips on storing print media and suppliesp.18Tips on preventing jamsp.19How to load the 250-sheet and 550-sheet traysp.20How to load the manual feederp.24How to use the rear exitp.25How to clear paper jamsp.26Printing tasksp.29How to manually feed a print jobp.30How to print on both sides of the paper (manual duplex)p.32How to print multiple page images on one page (N-upprinting)p.34How to print a bookletp.35How to print a posterp.36How to print on letterheadp.37How to print using an overlay or a watermarkp.37How to cancel a print jobp.39How to install optionsp.40How to access the system boardp.41How to add a memory cardp.45How to add a flash cardp.46How to install a 550-sheet drawerp.48How to get the printer driver to recognize installed optionsp.49Using the operator panelp.50Overview of the operator panelp.51Understanding the operator panel lightsp.52Operator panel codesp.57Understanding the printer configuration menusp.83Printing the Printer Settings Configuration sheetp.83Configuration menus overviewp.84Software and network tasksp.88How to install drivers for local printingp.89How to print the menu settings and network setup pagesp.94How to print a test pagep.94How to configure for TCP/IPp.95How to set up the printer for network printingp.96Using the printer resident Web pagep.102Using the Local Printer Setup Utilityp.103Supplies informationp.104What supplies do I need and how do I order them?p.105How to conserve suppliesp.105How to know when you need new suppliesp.106How to change a toner cartridgep.108Lexmark Return Programp.111Recycling Lexmark productsp.111How to change a photoconductor kitp.112Troubleshootingp.115General problemsp.116Print quality problemsp.118Indexp.125
Page 1 of the Lexmark 230 user manual — User’s Reference
Page 1 · click to enlarge
Page 1

E230, E232, E330, E332n

User’s Reference

November 2003

www.lexmark.com

Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. © 2003 Lexmark International, Inc. All rights reserved. 740 West New Circle Road Lexington, Kentucky 40550

Page 2 of the Lexmark 230 user manual — Table of Contents
Page 2 · Contents
Contents

Contents

Contentsp.2Noticesp.6Edition noticep.6Trademarksp.6Licensing noticep.7Safety informationp.7Laser noticep.7The United Kingdom Telecommunications Act 1984p.7Conventionsp.7Electronic emission noticesp.7Printer energy consumptionp.9Statement of Limited Warrantyp.9Printer overviewp.11Print media tasks and tipsp.13What types of print media can be loaded?p.14Where can print media be loaded in the printer?p.15Tips on choosing the right print mediap.16Tips on storing print media and suppliesp.18Tips on preventing jamsp.19How to load the 250-sheet and 550-sheet traysp.20How to load the manual feederp.24How to use the rear exitp.25How to clear paper jamsp.26Printing tasksp.29How to manually feed a print jobp.30How to print on both sides of the paper (manual duplex)p.32How to print multiple page images on one page (N-upprinting)p.34How to print a bookletp.35How to print a posterp.36How to print on letterheadp.37How to print using an overlay or a watermarkp.37How to cancel a print jobp.39How to install optionsp.40How to access the system boardp.41How to add a memory cardp.45How to add a flash cardp.46How to install a 550-sheet drawerp.48How to get the printer driver to recognize installed optionsp.49Using the operator panelp.50Overview of the operator panelp.51Understanding the operator panel lightsp.52Operator panel codesp.57Understanding the printer configuration menusp.83Printing the Printer Settings Configuration sheetp.83Configuration menus overviewp.84Software and network tasksp.88How to install drivers for local printingp.89How to print the menu settings and network setup pagesp.94How to print a test pagep.94How to configure for TCP/IPp.95How to set up the printer for network printingp.96Using the printer resident Web pagep.102Using the Local Printer Setup Utilityp.103Supplies informationp.104What supplies do I need and how do I order them?p.105How to conserve suppliesp.105How to know when you need new suppliesp.106How to change a toner cartridgep.108Lexmark Return Programp.111Recycling Lexmark productsp.111How to change a photoconductor kitp.112Troubleshootingp.115General problemsp.116Print quality problemsp.118Indexp.125
Page 6 of the Lexmark 230 user manual — Trademarks
Page 6 · click to enlarge
Page 6

Notices

of publications related to this product by calling 1-800-553-9727. In the United Kingdom and Eire, call +44 (0)8704 440 044. In other countries, contact your point of purchase. References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility. © 2003 Lexmark International, Inc. All rights reserved. UNITED STATES GOVERNMENT RIGHTS This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.

SectionPage Edition notice6 Trademarks6 Licensing notice7 Safety information7 Laser notice7 The United Kingdom Telecommunications Act 19847 Conventions7 Electronic emission notices7 Printer energy consumption9 Statement of Limited Warranty9

Trademarks

Edition notice

Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. PictureGrade is a trademark of Lexmark International, Inc. PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands. PostScript® is a registered trademark of Adobe Systems Incorporated. PostScript 3 is Adobe Systems’ designation of a set of printer commands (language) and functions included in its software products. This printer is intended to be compatible with the PostScript 3 language. This means the printer recognizes PostScript 3 commands used in various application programs, and that the printer emulates the functions corresponding to the commands. Details relating to compatibility are included in the Technical Reference. Other trademarks are the property of their respective owners.

EditionNovember 2003

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time. Comments about this publication may be addressed to Lexmark International, Inc., Department F95/032-2, 740 West New Circle Road, Lexington, Kentucky 40550, U.S.A. In the United Kingdom and Eire, send to Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. You can purchase additional copies

Page 7 of the Lexmark 230 user manual — Electronic emission notices
Page 7 · click to enlarge
Page 7

Licensing notice

Laser notice

The printer resident software contains:

The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1. Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 5 milliwatt gallium arsenide laser operating in the wavelength region of 770-795 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.

  • Software developed and copyrighted by Lexmark
  • Lexmark modified software licensed under the provisions of the GNU General Public License version 2 and the GNU Lesser General Public License version 2.1
  • Software licensed under the BSD license and warranty statements Click the title of the document you want to review:

BSD License and Warranty statements

GNU General Public License

The United Kingdom Telecommunications Act 1984

The Lexmark modified GNU licensed software is free software; you can redistribute it and/or modify it under the terms of the licenses referenced above. These licenses do not provide you any rights to the Lexmark copyrighted software in this printer. Since the GNU licensed software that the Lexmark modifications are based upon is supplied explicitly without warranty, use of the Lexmark modified version is similarly provided without warranty. See the warranty disclaimers in the referenced licenses for additional details. To obtain source code files for the Lexmark modified GNU licensed software, launch the drivers CD that shipped with your printer and click Contact Lexmark.

This apparatus is approved under the approval number NS/G/1234/J/100003 for the indirect connections to the public telecommunications systems in the United Kingdom.

Conventions

Safety information

  • If your product is not marked with this symbol , it must be connected to an electrical outlet that is properly grounded. CAUTION: Do not set up this product or make any electrical or cabling connections, such as the power cord or telephone, during a lightning storm.
  • The power cord must be connected to an electrical outlet that is near the product and easily accessible.
  • Refer service or repairs, other than those described in the operating instructions, to a professional service person.
  • This product is designed, tested, and approved to meet strict global safety standards with the use of specific Lexmark components. The safety features of some parts may not always be obvious. Lexmark is not responsible for the use of other replacement parts.
  • Your product uses a laser. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
  • Your product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.

Electronic emission notices

Federal Communications Commission (FCC) compliance information statement

The Lexmark E230, Machine Type 4505-100, Lexmark E232, Machine Type 4505-200, Lexmark E330, Machine Type 4505-300, and Lexmark E332n, Machine Type 4505-310, have been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The FCC Class B limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Page 8 of the Lexmark 230 user manual — ENERGY STAR
Page 8 · click to enlarge
Page 8
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult your point of purchase or service representative for additional suggestions. The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment. Note: To assure compliance with FCC regulations on electromagnetic interference for a Class B computing device, use a properly shielded and grounded cable such as Lexmark part number 1329605 for parallel attach or 12A2405 for USB attach. Use of a substitute cable not properly shielded and grounded may result in a violation of FCC regulations. Any questions regarding this compliance information statement should be directed to:

If your product includes the following symbol on the regulatory label: the following statement is applicable to your product.

Lexmark 230 — Licensing notice diagram (page 8)
Fig. 1 · Licensing notice

This equipment has undergone EMC registration as a household product. It can be used in any area, including a residential area.

The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.

1-meter average sound pressure, dBA Printing51—Machine types 4505-100, 4505-200, 4546-xxx 52—Machine types 4505-300, 4505-310, 4547-xxx Idling30

Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232-3000

ENERGY STAR

Industry Canada compliance statement

The EPA ENERGY STAR Office Equipment program is a partnership effort with office equipment manufacturers to promote the introduction of energy-efficient products and to reduce air pollution caused by power generation. Companies participating in this program introduce products that power down when they are not being used. This feature will cut the energy used by up to 50 percent. Lexmark is proud to be a participant in this program. As an ENERGY STAR Partner, Lexmark International, Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Avis de conformité aux normes de l’industrie du Canada

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

European Community (EC) directives conformity

This product is in conformity with the protection requirements of EC Council directives 89/336/EEC and 73/23/EEC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits. A declaration of conformity with the requirements of the directives has been signed by the Director of Manufacturing and Technical Support, Lexmark International, S.A., Boigny, France. This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.

Lexmark 230 — ENERGY STAR diagram (page 8)
Fig. 2

Korean MIC statement · Noise emission levels · Japanese VCCI notice

Page 9 of the Lexmark 230 user manual — Printer energy consumption
Page 9 · click to enlarge
Page 9

Printer energy consumption

Statement of Limited Warranty

The following table documents the power consumption characteristics of the printer.

Lexmark International, Inc., Lexington, KY

This warranty applies to the United States and Canada. For customers outside the U.S. and Canada, refer to the country-specific warranty information that came with your printer.

ModeDescriptionPower consumption (by Machine Type) 4505-100, 4505-200, 4546-xxx4505-300, 4505-310, 4547-xxx PrintingPrinter is generating hard copy output370 W420 W ReadyPrinter is waiting for a print job65 W80 W Power SaverPrinter is in energy saving mode6 W7 W OffPrinter is plugged into a wall outlet, but switch is turned off0 W0 W

Lexmark E230, E232, E330, E332n

This Statement of Limited Warranty applies to this product if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark remarketer, referred to in this statement as “Remarketer.”

Lexmark warrants that this product:

  • Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
  • Is free from defects in material and workmanship
  • Conforms to Lexmark’s official published specifications
  • Is in good working order If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair without charge. If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was designed. To obtain warranty service, you may be required to present the feature or option with the product. If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.

The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.

As part of the ENERGY STAR program, this printer is designed with an energy-saving mode called Power Saver. The Power Saver Mode is equivalent to the EPA Sleep Mode. The Power Saver Mode saves energy by lowering power consumption during extended periods of inactivity. The Power Saver Mode is automatically engaged after this printer is not used for a specified period of time, called the Power Saver Timeout. The factory default Power Saver Timeout is 15 minutes for the Lexmark E230 and 30 minutes for the Lexmark E232, Lexmark E330, and Lexmark E332n. By using the printer configuration menus, the Power Saver Timeout can be modified between 1 minute and 240 minutes. Setting the Power Saver Timeout to a low value reduces energy consumption, but may increase the response time of the printer. Setting the Power Saver Timeout to a high value maintains a fast response, but uses more energy. If the Power Saver Mode is affecting the effective use of this printer, this mode can be disabled from the Local Printer Setup Utility (see page 103) or, if you have a network model, from the printer’s resident Web page (see page 102).

The warranty period is 12 months and starts on the date of original purchase as shown on the purchase receipt. To obtain warranty service you may be required to present proof of original purchase. Warranty service will be provided at a Remarketer or a Lexmark designated location. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the designated location. When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item. The replacement item assumes the remaining warranty period of the original product. Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, or damaged beyond repair. Also, such product must be free of any legal obligation or restrictions that prevent its exchange. Before you present this product for warranty service, remove all programs, data, and removable storage media.

It is sometimes helpful to calculate the total printer energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the printer spends in each mode in order to calculate energy usage. The total printer energy usage is the sum of each mode's energy usage.

Show 4 more labels / short text on this page
Warranty · Power Saver · Warranty service · Total energy usage
Page 10 of the Lexmark 230 user manual — Printer energy consumption
Page 10 · click to enlarge
Page 10

For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area, please contact Lexmark at 1-859-232-3000, or on the World Wide Web at http:// support.lexmark.com. Remote technical support is provided for this product throughout its warranty period. Lexmark offers a variety of extended warranty programs that include an extension of technical support. For products no longer covered by a Lexmark warranty, technical support may only be available for a fee.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

We do not warrant uninterrupted or error-free operation of a product. Warranty service does not include repair of failures caused by:

  • Modification or attachments
  • Accidents or misuse
  • Unsuitable physical or operating environment
  • Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
  • Operation of a product beyond the limit of its duty cycle
  • Failure to have installed a maintenance kit as specified (if applicable)
  • Use of printing media outside of Lexmark specifications
  • Use of other than Lexmark supplies (such as toner cartridges, inkjet cartridges, and ribbons)
  • Use of other than Lexmark product or component ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD.

Your sole remedy under this Statement of Limited Warranty is set forth in this section. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this Statement of Limited Warranty, you may recover actual damages up to the limit set forth in the following paragraph. Lexmark's liability for actual damages from any cause whatsoever will be limited to the greater of 1) $5,000 or 2) the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. In no event will Lexmark be liable for any lost profits, lost savings, incidental damage, or other economic consequential damages. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim. This limitation of remedies also applies to any developer of materials supplied to Lexmark. Lexmark’s and the developer’s limitations of remedies are not cumulative. Such developer is an intended beneficiary of this limitation.

Additional rights · Extent of warranty · Limitation of liability

Page 11 of the Lexmark 230 user manual — 1 Printer overview
Page 11 · click to enlarge
Page 11

1 Printer overview

Dust cover (some models)

Show 10 more labels / short text on this page
150-sheet output bin · Paper support · Front cover · Operator panel · Manual feeder · 250-sheet tray · Optional 550-sheet drawer · Rear paper exit · Power button · Printer overview
Page 12 of the Lexmark 230 user manual — Printer overview
Page 12 · click to enlarge
Page 12

The operator panel has 5 lights and 2 buttons.

Lexmark 230 — Printer overview diagram (page 12)
Fig. 3 · Printer overview

Toner Low / Replace PC Kit

  • Press and release Continue to resume printing.
  • Press and release Continue twice quickly to display a secondary error code.
  • Press and release Cancel to cancel the job currently printing.
  • Press and hold Cancel until all of the lights come on to reset the printer.
Show 7 more labels / short text on this page
Continue · Cancel · Ready · Load Paper · Paper Jam · Error · Printer overview
Page 13 of the Lexmark 230 user manual — 2 Print media tasks and tips
Page 13 · click to enlarge
Page 13

2 Print media tasks and tips

What types of print media can be loaded? 14

Where can print media be loaded in the printer? 15

How to load the 250-sheet and 550-sheet trays 20

How to load the manual feeder 24

How to use the rear exit 25

How to clear paper jams 26

Print media tasks and tips

Section Page

Page 14 of the Lexmark 230 user manual — What types of print media can be loaded?
Page 14 · click to enlarge
Page 14

What types of print media can be loaded?

Get the most out of your printer by properly loading the trays. Never mix media types within a tray.

Source Sizes Types Weight Capacity* (sheets)

A4, A5, JIS B5, letter, legal, executive, folio, statement, Universal‡

Plain paper, transparencies, labels

60–90 g/m2 (16–24 lb)

  • 250 paper
  • 50 labels
  • 50 transparencies

A4, A5, JIS B5, letter, legal, executive, folio, statement, Universal‡

Plain paper, transparencies, labels

60–163 g/m2 (16–43 lb)

  • 550 paper
  • 50 labels
  • 50 transparencies

Manual feeder A4, A5, JIS B5, letter, legal, executive, folio, statement, Universal‡

Plain paper, transparencies, labels

60–163 g/m2 (16–43 lb)

Card stock† • 120–163 g/m2

(16–90 lb) Index Bristol

  • 75–163 g/m 2

7¾, 9, 10, DL, C5, B5 Envelopes 90 g/m2 (24 lb)

* Capacity for 20 lb print media, unless otherwise noted. † Grain short is recommended. Use rear exit for best results. ‡ Universal size ranges:

– Tray 1: 89–216 x 210–356 mm (3.5–8.5 x 8.27–14.0 in.) – Tray 2: 148–216 x 210–356 mm (5.83–8.5 x 8.27–14.0 in.) – Manual feeder: 76–216 x 127–356 mm (3.0–8.5 x 5.0–14.0 in.) (includes 3 x 5 in. cards)

Print media tasks and tips

Show 5 more labels / short text on this page
Tray 1 · (250-sheet tray) · Tray 2 · (550-sheet tray) · (50–100 lb) Tag
Page 15 of the Lexmark 230 user manual — Where can print media be loaded in the printer?
Page 15 · click to enlarge
Page 15

Where can print media be loaded in the printer?

Your printer has two standard paper sources: an automatic 250-sheet paper feeder (Tray 1) and a single-sheet manual feeder. Use Tray 1 for most print jobs. Use the manual feeder for a single piece of paper, transparency, envelope, paper label, card stock, or index card. You can increase paper capacity by purchasing an optional 550-sheet drawer.

An output bin on top of the printer holds up to 150 sheets. The single-sheet rear exit provides a straight-through paper path to help reduce curling and potential jams. This is especially useful for specialty media, such as transparencies, envelopes, paper labels, card stock, or index cards.

Print media tasks and tips

Show 8 more labels / short text on this page
150-sheet output bin · Front paper support · Front cover · Operator panel · Manual feeder · 250-sheet tray · Optional 550-sheet drawer · Rear paper exit
Page 16 of the Lexmark 230 user manual — Transparencies
Page 16 · click to enlarge
Page 16

Tips on choosing the right print media

Selecting the right paper or other media reduces printing problems. For best print quality, try a sample of the paper or other media you are considering before buying large quantities.

Refer to the Card Stock & Label Guide available on our Lexmark Web site at www.lexmark.com for more information about which paper provides optimum results for your printing environment.

Paper

  • For the best print quality, use 20 lb (75 g/m 2 ) xerographic, grain long paper.

The printer can automatically feed paper weights from 60 to 90 g/m2 (16 to 24 lb bond) grain long. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, causing jams. Paper heavier than 90 g/m2 (24 lb) should be fed through the optional 550-sheet tray or the manual feeder.

  • The laser printing process heats paper to high temperatures of 170°C (338°F) for non-MICR applications. Use only paper able to withstand these temperatures without discoloring, bleeding, or releasing hazardous emissions. Check with the manufacturer or vendor to determine whether the paper you have chosen is acceptable for laser printers.

Preprinted forms and letterhead

  • Use only forms and letterhead printed using an offset lithographic or engraved printing process.
  • Choose papers that absorb ink, but do not bleed.
  • Avoid papers with rough or heavily textured surfaces.

Use papers printed with heat-resistant inks designed for use in xerographic copiers. The ink must withstand temperatures of 170°C (338°F) without melting or releasing hazardous emissions. Use inks that are not affected by the resin in toner. Inks that are oxidation-set or oil-based should meet these requirements; latex inks might not. If you are in doubt, contact your paper supplier.

Preprinted papers such as letterhead must be able to withstand temperatures up to 170°C (338°F) without melting or releasing hazardous emissions.

Transparencies

  • Use transparencies designed specifically for laser printers. Transparencies must be able to withstand temperatures of 170°C (338°F) without melting, discoloring, offsetting, or releasing hazardous emissions.

We recommend Lexmark laser printer transparencies: part number 70X7240 for letter size transparencies; part number 12A5010 for A4 size transparencies.

  • To prevent print quality problems, avoid getting fingerprints on the transparencies.

Print media tasks and tips

Page 17 of the Lexmark 230 user manual — Labels
Page 17 · click to enlarge
Page 17

Envelopes

  • Use envelopes made from 24 lb (90 g/m 2 ) bond paper.
  • Do not use envelopes that:

– Have excessive curl – Are stuck together – Are damaged in any way – Contain windows, holes, perforations, cutouts, or embossments – Use metal clasps, string ties, or metal folding bars – Have postage stamps attached – Have any exposed adhesive when the flap is in the sealed position

  • Use envelopes that can withstand temperatures of 170°C (338°F) without:

– sealing – excessive curling – wrinkling – releasing hazardous emissions

If you have any doubts about the envelopes you are considering using, check with the envelope supplier.

  • A combination of high humidity (over 60%) and the high printing temperatures may seal the envelopes.

Labels

  • Do not use labels that have exposed adhesive on the sheets.
  • Do not print a large number of labels continuously.
  • Do not use vinyl labels.
  • Use labels that can withstand temperatures of 170°C (338°F) without sealing, excessive curling, wrinkling, or releasing hazardous emissions. Label adhesives, face sheet (printable stock), and topcoats must also be able to withstand 25 pounds per square inch (psi) (172 kilopascals) pressure.

Print media tasks and tips

Page 18 of the Lexmark 230 user manual — Storing supplies
Page 18 · click to enlarge
Page 18

Card stock

  • Preprinting, perforation, and creasing can significantly affect the print quality and cause media handling or jamming problems.
  • Avoid using card stock that may release hazardous emissions when heated.
  • Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting introduces semi-liquid and volatile components into the printer.
  • Use card stock with a maximum weight of 163 g/m 2 and a minimum size of 76 x 127 mm (3 x 5 in.).

Tips on storing print media and supplies

Storing paper

Use the following guidelines to avoid paper feeding problems and uneven print quality.

  • Store paper in an environment where the temperature is approximately 21°C (70°F) and the relative humidity is 40%.
  • Store cartons of paper on a pallet or shelf rather than directly on the floor.
  • If you store individual packages of paper out of the original carton, make sure they rest on a flat surface so the edges do not buckle, curl, or become damaged.
  • Do not place anything on top of paper packages.

Storing supplies

Choose a cool, clean storage area for your printer supplies. Store supplies right side up in their original packaging until you are ready to use them.

Do not expose supplies to:

  • Direct sunlight
  • Temperatures above 35°C (95°F)
  • High humidity (above 80%)
  • Salty air
  • Corrosive gases
  • Heavy dust

Print media tasks and tips

Page 19 of the Lexmark 230 user manual — Tips on preventing jams
Page 19 · click to enlarge
Page 19

Tips on preventing jams

You can avoid most paper jams by correctly loading paper and specialty media in the printer.

The following hints can help you avoid paper jams:

  • Do not load wrinkled, creased, or damp paper.
  • Never mix media types within a tray.
  • Flex, fan, and straighten paper before you load it.
  • Do not exceed the maximum stack height.
  • Push all trays firmly into the printer after loading them.
  • Make sure the guides in the trays are positioned snug against the paper or specialty media.
  • Do not remove paper trays while a job is printing. Wait for a Load Paper light sequence (see “Load media” on page 61 ) before you remove the tray.
  • Before loading transparencies, fan the stack to prevent sheets from sticking together.
  • Do not use envelopes that:

– Have excessive curl – Are stuck together – Are damaged in any way – Contain windows, holes, perforations, cutouts, or embossments – Have metal clasps, string ties, or metal folding bars – Have postage stamps attached – Have any exposed adhesive when the flap is in the sealed position

  • Use only recommended paper. Refer to the Card Stock & Label Guide available on our Lexmark Web site at <a href="http://www.lexmark.com" rel="nofollow noopener" target="_blank">www.lexmark.com</a> for more information about which paper provides optimum results for your printing environment.
  • If you need detailed information before purchasing large quantities of customized paper, refer to the Card Stock & Label Guide .

Print media tasks and tips

Page 20 of the Lexmark 230 user manual — How to load the 250-sheet and 550-sheet trays
Page 20 · click to enlarge
Page 20

How to load the 250-sheet and 550-sheet trays

Follow these instructions to load paper in the 250-sheet tray and 550-sheet tray.

1 Remove the tray.

the paper tray. See “Extending the tray for legal or folio size paper” on page 23 for instructions.

2 Prepare a stack of paper for loading by flexing or fanning it back and forth. Straighten the edges on a level surface.

Print media tasks and tips

Page 21 of the Lexmark 230 user manual — How to load the 250-sheet and 550-sheet trays
Page 21 · click to enlarge
Page 21

3 Load the paper in the tray with the print side facing down.

with the logo should be placed at the front of the tray.

Make sure the paper is below the max fill line on the side guides. Overloading may cause jams.

4 Slide the two side guides and the back guide until they fit snugly against the stack of paper.

Print media tasks and tips

Page 22 of the Lexmark 230 user manual — How to load the 250-sheet and 550-sheet trays
Page 22 · click to enlarge
Page 22

5 Insert the tray.

6 Extend the paper support on the output bin.

Print media tasks and tips

Page 23 of the Lexmark 230 user manual — Attaching the dust cover
Page 23 · click to enlarge
Page 23

Extending the tray for legal or folio size paper

To load legal or folio size paper, you need to extend the paper tray. You should also attach the dust cover on the back of the printer to protect the tray while it is extended.

1 Press down on the latch at the back of the tray.

2 Expand the tray until the extender locks into place.

Attaching the dust cover

The dust cover helps protect the paper tray from the environment as well as keep the tray from being knocked out of position while it is extended.

with a dust cover.

Attach the dust cover to the back of the printer by aligning the tabs on the cover to the holes on the printer and snap the cover in place.

Print media tasks and tips

Page 24 of the Lexmark 230 user manual — How to load the manual feeder
Page 24 · click to enlarge
Page 24

How to load the manual feeder

The manual feeder is located at the front of your printer and can only feed one sheet of print media at a time. You can use the manual feeder to make quick runs of paper types or sizes that are not currently loaded in the paper tray.

For information on acceptable print media to use in the manual feeder, see “What types of print media can be loaded?” on page 14. Using only the specified print media helps prevent paper jams and print quality problems.

manual feeder. See “How to manually feed a print job” on page 30 for more information.

To load the manual feeder:

1 Place a sheet of the selected print media, print side facing up, at the center of the manual feeder, but only to the point where its leading edge can contact the paper guides. Otherwise, the printer will engage the print media too soon and likely skew the print job.

2 Adjust the paper guides to the print media’s width.

3 Hold both sides of the print media close to the manual feeder and push it into the printer until it automatically engages.

There is a brief pause between the time the printer engages the print media and when it feeds into the printer.

  • Insert envelopes with the flap side down and with the stamp area as shown.
  • Hold transparencies by the edges and avoid touching the print side. Oil from your fingers can affect print quality.
  • Load letterhead face-up, with the top of the sheet first.
  • If you experience problems with paper feed, turn the paper over.

Print media tasks and tips

Page 25 of the Lexmark 230 user manual — How to use the rear exit
Page 25 · click to enlarge
Page 25

How to use the rear exit

The single-sheet rear exit provides a straight-through paper path to help reduce curling and potential jams. This is especially useful for specialty media, such as transparencies, envelopes, labels, card stock, or index cards.

To use the rear exit, simply open the rear exit door. When the rear exit door is open, all print media comes out the rear exit. When closed, all media is sent to the output bin on top of the printer.

Print media tasks and tips

Page 26 of the Lexmark 230 user manual — How to clear paper jams
Page 26 · click to enlarge
Page 26

How to clear paper jams

When a paper jam occurs, the printer stops and the operator panel’s Paper Jam and

Continue lights come on. Press and release Continue twice quickly to display the specific secondary error paper jam light sequence. See “Secondary error codes” on page 69 for more information.

We recommend that you clear the entire paper path when a paper jam occurs.

To clear a paper jam:

1 If you are feeding paper from a tray, remove the tray, and then remove any jams.

Print media tasks and tips

Page 27 of the Lexmark 230 user manual — How to clear paper jams
Page 27 · click to enlarge
Page 27

2 Open the front cover and remove the print cartridge assembly.

Lexmark 230 — How to clear paper jams diagram (page 27)
Fig. 4 · How to clear paper jams

period of time. Extended light exposure can cause print quality problems.

3 Remove any jams in the area behind the print cartridge assembly.

Lexmark 230 — How to clear paper jams diagram (page 27)
Fig. 5 · How to clear paper jams

Print media tasks and tips

Page 28 of the Lexmark 230 user manual — How to clear paper jams
Page 28 · click to enlarge
Page 28

4 Lift the flap at the front of the printer and remove any jams beneath the flap.

5 Open the rear exit and remove any jams.

6 After you have cleared the jams, reinstall the print cartridge assembly, make sure all printer

covers and trays are closed, and then press Continue to resume printing.

Print media tasks and tips

Page 29 of the Lexmark 230 user manual — 3 Printing tasks
Page 29 · click to enlarge
Page 29

3 Printing tasks

How to manually feed a print job 30

How to print on both sides of the paper (manual duplex) 32

How to print multiple page images on one page (N-up printing) 34

How to print a booklet 35

How to print a poster 36

How to print on letterhead 37

How to print using an overlay or a watermark 37

How to cancel a print job 39

Section Page · Printing tasks

Page 30 of the Lexmark 230 user manual — How to manually feed a print job
Page 30 · click to enlarge
Page 30

How to manually feed a print job

The manual feeder is located at the front of your printer and can only feed one sheet of print media at a time. For information on acceptable print media to use in the manual feeder, see “What types of print media can be loaded?” on page 14.

When using the manual feeder, send the print job to the printer before loading the print media. When the printer is ready, it will display the Load Manual Feeder light sequence, at which point you should load the media.

To manually feed a print job:

1 From the computer’s software application, select File Æ Print.

2 Click Properties (or Options, Printer, or Setup, depending on the application) to view the printer driver settings.

3 Click the Paper tab.

4 Select Manual paper from the Paper tray drop-down list.

5 Select the appropriate Paper size and type.

6 Click OK.

7 Click OK on the Print window to send the job to print.

The printer displays the Load Manual Feeder light sequence.

Lexmark 230 — How to manually feed a print job diagram (page 30)
Fig. 6 · How to manually feed a print job

Printing tasks

Page 31 of the Lexmark 230 user manual — How to manually feed a print job
Page 31 · click to enlarge
Page 31

8 Place a sheet of the selected print media, print side facing up, at the center of the manual feeder, but only to the point where its leading edge can contact the paper guides.

  • Hold transparencies by the edges and avoid touching the print side. Oil from your fingers can affect print quality.
  • Insert envelopes with the flap side face down and with the stamp area as shown.
  • Load letterhead face up, with the top of the sheet first.
  • If you experience problems with paper feed, turn the paper over.

9 Adjust the paper guides to the print media’s width.

10 Hold both sides of the print media close to the manual feeder and push it into the printer until it automatically engages.

There is a brief pause between the time the printer engages the print media and when it feeds into the printer.

Printing tasks

Page 32 of the Lexmark 230 user manual — How to print on both sides of the paper (manual duplex)
Page 32 · click to enlarge
Page 32

How to print on both sides of the paper (manual duplex)

Printing on both sides of the paper reduces printing costs.

Although you can use Tray 1 or the 550-sheet tray to print the first side of the duplex job, only use Tray 1 to print the second side.

You can choose how you want your job duplexed: Long Edge or Short Edge.

  • Long Edge means pages are bound along the long edge of the page (left edge for portrait, top edge for landscape).

Front of next sheet

Front of next sheet

  • Short Edge means pages are bound along the short edge of the page.

Back of sheet Front of sheet

To manually duplex a print job:

1 From the computer’s software application, select File Æ Print.

2 Click Properties (or Options, Printer, or Setup, depending on the application) to view the printer driver settings.

3 From the Page Layout tab, select 2-sided printing.

Show 9 more labels / short text on this page
Landscape · Portrait · Back of sheet · Back of sheet · Portrait · Back of sheet · Landscape · Front of sheet · Printing tasks
Page 33 of the Lexmark 230 user manual — How to print on both sides of the paper (manual duplex)
Page 33 · click to enlarge
Page 33

4 Select either Long Edge or Short Edge.

5 Select Manual 2-sided printing.

6 Click the Paper tab.

7 Select the appropriate Input options for your print job.

8 Click OK.

9 Click OK on the Print window.

The printer prints every other page of the document first. Once the first side of your job prints,

Lexmark 230 — How to print on both sides of the paper (manual duplex) diagram (page 33)
Fig. 7 · How to print on both sides of the paper (manual dupl…

the Load Paper light comes on and the Continue light blinks.

10 Load the paper back into the printer with the already-printed side up and the top of the page toward the front of the tray.

Printing tasks

Page 34 of the Lexmark 230 user manual — How to print multiple page images on one page (N-up printing)
Page 34 · click to enlarge
Page 34

How to print multiple page images on one page (N-up printing)

The Multipage Printing (N-up) setting is used to print multiple page images on a single page. For example, 2-Up means two page images are printed on one page, 4-up means four page images are printed on one page, and so on.

The printer uses the Multipage Order, Multipage View, and Multipage Border settings to determine the order and orientation of the page images, and whether a border is printed around each page image.

1 From the computer’s software application, select File Æ Print.

2 Click Properties (or Options, Printer, or Setup, depending on the application) to view the printer driver settings.

3 From the Page Layout tab, select the number of images per sheet (from the Multipage printing section) and the orientation you would like the paper to have.

The positioning depends on the number of images and whether the images are portrait or landscape in orientation.

For example, if you select 4-Up multipage printing and portrait orientation, the results differ depending on the Multipage Order value you select:

4 To print a visible border around each page image, select Print page borders.

5 Click OK.

6 Click OK on the Print window to send the job to print.

Across Down · Printing tasks

Page 35 of the Lexmark 230 user manual — How to print a booklet
Page 35 · click to enlarge
Page 35

How to print a booklet

The Booklet setting lets you print multiple pages in booklet form without having to re-format your document so the pages print in the proper order. The pages print so that the finished collated document may be folded along the center of each page to form a booklet.

If the document contains many pages, a booklet may have too many pages to fold easily. If you are printing a fairly large booklet, you might want to use the Sheets per Bundle option to specify how many physical pages are put into one bundle. The printer will print the necessary number of bundles, which you can then bind into one booklet. Printing in bundles helps the outside edge of the pages line up more evenly.

You must specify whether or not you want to print using any Duplex printing options before you select to print using the booklet function. Once you choose Print Using Booklet, the controls for the Duplex options are dimmed and remain at the last setting used.

1 From the computer’s software application, select File Æ Print.

2 Click Properties (or Options, Printer, or Setup, depending on the application) to view the printer driver settings.

3 From the Page Layout tab, click More Page Layout Options.

4 Click Booklet.

If your print job is large, you may want to use the Sheets per Bundle option.

5 Select the appropriate binding edge for your print job.

6 To print a visible fold mark on the pages, select Print fold mark.

7 Click OK twice.

8 Click OK on the Print window to send the job to print.

Printing tasks

Page 36 of the Lexmark 230 user manual — How to print a poster
Page 36 · click to enlarge
Page 36

How to print a poster

The Poster setting lets you print a single image across several pages. Once printed, you can combine the pages to create one large image.

1 From the computer’s software application, select File Æ Print.

2 Click Properties (or Options, Printer, or Setup, depending on the application) to view the printer driver settings.

3 From the Page Layout tab, click More Page Layout Options.

4 Click Poster.

5 Select the poster size you want by choosing the number of pages to use in the poster.

6 To print crop marks on the pages, select Print crop marks.

7 Select the amount of overlap you want each page to have.

8 Click OK twice.

9 Click OK on the Print window to send the job to print.

Printing tasks

Page 37 of the Lexmark 230 user manual — How to print using an overlay or a watermark
Page 37 · click to enlarge
Page 37

How to print on letterhead

To print on letterhead, make sure the paper is loaded with the proper orientation.

1 Make sure the letterhead is properly loaded according to the paper source you are using:

  • Tray 1 or 2 —Load the letterhead paper with the design side facing down. The top edge of the sheet with the logo should be placed at the front of the tray.
  • Manual feeder —Load the letterhead paper face-up, with the top of the sheet first.

letterhead when the printer displays the Load Manual Feeder light sequence (see “How to manually feed a print job” on page 30).

2 From the computer’s software application, select File Æ Print.

3 Click Properties (or Options, Printer, or Setup, depending on the application) to view the printer driver settings.

4 Click the Paper tab.

5 Select Letterhead from the Paper type drop-down lists.

6 Select the appropriate paper size and tray.

7 Click OK.

8 Click OK on the Print window to send the job to print.

How to print using an overlay or a watermark

Overlays and watermarks are templates that can be defined and then printed as a background on a form before the data from the current job is printed. Typical examples of overlays include company logos or letterheads, decorative borders, and simulated “preprinted” forms. Overlays can include text, graphics, or images. Watermarks are simple text. You can create overlays and watermarks and then download them directly to the printer, or you can create an overlay or watermark file on your system and then download it to the printer.

For information about how to create, save, or download an overlay or watermark, refer to the printer driver Help.

Printing tasks

Page 38 of the Lexmark 230 user manual — Using a watermark
Page 38 · click to enlarge
Page 38

Using an overlay

1 From the computer’s software application, select File Æ Print.

2 Click Properties (or Options, Printer, or Setup, depending on the application) to view the printer driver settings.

3 Click the Other Options tab.

4 Click Overlays.

5 Select which pages receive the overlay.

6 Select the overlay to use.

7 Select whether to place the overlay on top of or underneath the page image in the Overlay placement area.

8 Click OK.

Using a watermark

1 From the computer’s software application, select File Æ Print.

2 Click Properties (or Options, Printer, or Setup, depending on the application) to view the printer driver settings.

3 Click the Other Options tab.

4 Click Watermark.

5 Select which pages receive the watermark.

6 Select the watermark to use.

7 Select whether to place the watermark on top of or underneath the page image in the Watermark placement area.

8 Click OK.

Printing tasks

Page 39 of the Lexmark 230 user manual — From a Macintosh computer
Page 39 · click to enlarge
Page 39

How to cancel a print job

A print job can be canceled from the operator panel or from your computer. The Cancel job light sequence is displayed on the operator panel while the job is being cancelled.

From the printer operator panel

Press and release Cancel to cancel the job currently printing.

From a Windows computer

1 Click Start Æ Settings Æ Printers.

2 Double-click the printer you are using to print the job.

A list of print jobs appears.

3 Right-click the document you want to stop printing, and then click Cancel.

From a Macintosh computer

When you send a job to print, the printer icon appears on the desktop.

1 Double-click the printer icon on your desktop.

A list of print jobs appears.

2 Press Control and click the print job you want to cancel. Choose Stop Queue from the pop-up menu.

Printing tasks

Page 40 of the Lexmark 230 user manual — 4 How to install options
Page 40 · click to enlarge
Page 40

4 How to install options

How to access the system board 41

How to add a memory card 45

How to add a flash card 46

How to install a 550-sheet drawer 48

How to get the printer driver to recognize installed options 49

How to install options

Section Page

Page 41 of the Lexmark 230 user manual — How to access the system board
Page 41 · click to enlarge
Page 41

How to access the system board

To install a memory or flash card you must access the printer system board.

1 Open the front cover by pressing the button on the left side of the printer and lowering the cover.

How to install options

Page 42 of the Lexmark 230 user manual — How to access the system board
Page 42 · click to enlarge
Page 42

2 Open the rear exit.

Lexmark 230 — How to access the system board diagram (page 42)
Fig. 8 · How to access the system board

3 Open the side cover by pressing the two detents on the front right side of the machine and swinging the cover back.

Lexmark 230 — How to access the system board diagram (page 42)
Fig. 9 · How to access the system board

How to install options

Page 43 of the Lexmark 230 user manual — How to access the system board
Page 43 · click to enlarge
Page 43

4 Remove the two screws at the top and side of the metal plate covering the system board.

Lexmark 230 — How to access the system board diagram (page 43)
Fig. 10 · How to access the system board

5 Remove the metal plate by rotating it towards the front and to the right.

How to install options

Page 44 of the Lexmark 230 user manual — How to reattach the system board cover
Page 44 · click to enlarge
Page 44

How to reattach the system board cover

When you are finished adding a memory or flash card, be sure to properly reattach the system board’s metal cover.

1 Insert the two tabs on the right side of the metal plate into the holes toward the back of the system board and rotate the system board until it is flush against the printer.

Lexmark 230 — How to reattach the system board cover diagram (page 44)
Fig. 11 · How to reattach the system board cover

2 Screw in the two screws at the top and side of the metal plate.

3 Close the side cover.

4 Close the rear exit.

5 Close the front cover.

How to install options

Page 45 of the Lexmark 230 user manual — How to add a memory card
Page 45 · click to enlarge
Page 45

How to add a memory card

The system board has one connector for an optional memory card. The printer can support up to 64MB of additional memory (for a total of 80MB) for the Lexmark E232 and up to 128MB (for a total of 160MB) for the Lexmark E330 and Lexmark E332n. The Lexmark E230 does not support additional memory.

and unplug the power cord before continuing.

printer.

1 Access the system board (see How to access the system board).

2 Push open the latches on both ends of the memory connector.

3 Unpack the memory card.

damaged by static electricity. Touch something metal, such as the printer frame, before you touch a memory card.

Avoid touching the connection points along the edge of the card.

4 Align the notches on the bottom of the card with the notches on the connector.

5 Push the memory card firmly into the connector until the latches on either end of the connector snap into place.

It may require some force to fully seat the card.

6 Make sure each latch fits over the notch on each end of the card.

7 Reattach the system board cover (see How to reattach the system board cover).

8 See How to get the printer driver to recognize installed options.

How to install options

Page 46 of the Lexmark 230 user manual — How to add a flash card
Page 46 · click to enlarge
Page 46

How to add a flash card

The system board has one connector for an optional flash card. The printer can support 16MB and 32MB flash cards.

unplug the power cord before continuing.

1 Access the system board (see How to access the system board).

2 Unpack the flash card.

as the printer frame, before you touch a card.

Avoid touching the metal pins on the bottom of the card.

3 Holding the card by its sides, align the pins on the card with the holes on the system board.

How to install options

Metal pins

Page 47 of the Lexmark 230 user manual — How to add a flash card
Page 47 · click to enlarge
Page 47

4 Push the flash card firmly into place.

Lexmark 230 — How to add a flash card diagram (page 47)
Fig. 12 · How to add a flash card

The entire length of the connector on the flash card must touch and be flush against the system board.

Be careful not to damage the connectors.

5 Reattach the system board cover (see How to reattach the system board cover).

6 See How to get the printer driver to recognize installed options.

How to install options

Page 48 of the Lexmark 230 user manual — How to install a 550-sheet drawer
Page 48 · click to enlarge
Page 48

How to install a 550-sheet drawer

Your printer supports one optional drawer that lets you load up to 550 sheets of paper.

off and unplug the power cord before continuing.

1 Unpack the 550-sheet drawer and remove any packing material.

2 Place the drawer in the location you have chosen for your printer.

3 Align the holes in the printer with the positioning posts on the 550-sheet drawer and lower the printer into place.

4 See How to get the printer driver to recognize installed options.

How to install options

Page 49 of the Lexmark 230 user manual — How to get the printer driver to recognize installed options
Page 49 · click to enlarge
Page 49

How to get the printer driver to recognize installed options

After the printer is turned on, the printer driver should automatically recognize an option you installed. If it does not, you can add it manually.

under Software and network tasks. After you have installed a printer driver, return here to complete these instructions.

1 Click Start Æ Settings Æ Printers.

2 Select the printer’s icon.

3 Click File Æ Properties.

4 Click the Install Options tab.

5 Add the appropriate options to your configuration:

  • 550-Sheet Tray or Flash Card —Select the option you installed from the Available options list and click Add .
  • Memory Card —Increase the printer memory to the appropriate number.

6 Click OK.

How to install options

Page 50 of the Lexmark 230 user manual — 5 Using the operator panel
Page 50 · click to enlarge
Page 50

5 Using the operator panel

Overview of the operator panel 51

Understanding the operator panel lights 52

Operator panel codes 57

Using the operator panel

Section Page

Page 51 of the Lexmark 230 user manual — Overview of the operator panel
Page 51 · click to enlarge
Page 51

Overview of the operator panel

The operator panel has 5 lights and 2 buttons.

Lexmark 230 — Overview of the operator panel diagram (page 51)
Fig. 13 · Overview of the operator panel

Toner Low / Replace PC Kit

  • Press and release Continue to resume printing.
  • Press and release Continue twice quickly to display a secondary error code.
  • Press and release Cancel to cancel the job currently printing.
  • Press and hold Cancel until all of the lights come on to reset the printer.

Using the operator panel

Show 6 more labels / short text on this page
Continue · Cancel · Ready · Load Paper · Paper Jam · Error
Page 52 of the Lexmark 230 user manual — Understanding the operator panel lights
Page 52 · click to enlarge
Page 52

Understanding the operator panel lights

The operator panel lights mean different things, depending on their sequence. Lights that are off, on, and/or blinking indicate printer conditions such as printer status, intervention, or service.

The following tables show the most common light sequences. Click the indicated page for more information on what it means.

Lexmark 230 — Understanding the operator panel lights diagram (page 52)
Fig. 14 · Understanding the operator panel lights
Page57 58 59 59 60 60 61 61 62 62 63

Using the operator panel

Common light sequences

Page 53 of the Lexmark 230 user manual — Understanding the operator panel lights
Page 53 · click to enlarge
Page 53

Common light sequences (continued)

Lexmark 230 — Understanding the operator panel lights diagram (page 53)
Fig. 15 · Understanding the operator panel lights
Page63 64 64 65 65 66 66 67 67 68 68

* See “Secondary errors” on page 54 for more information.

Using the operator panel

Page 54 of the Lexmark 230 user manual — Secondary errors
Page 54 · click to enlarge
Page 54

Secondary errors

  • When the Error and Continue lights are both on, a secondary error has occurred.
  • When the Paper Jam and Continue lights are both on, a paper jam secondary error has occurred.

Press and release Continue twice quickly to display the secondary error code light sequence. The following table shows what these light sequences mean and where to go for help.

Using the operator panel

Page 55 of the Lexmark 230 user manual — Understanding the operator panel lights
Page 55 · click to enlarge
Page 55
Lexmark 230 — Understanding the operator panel lights diagram (page 55)
Fig. 16 · Understanding the operator panel lights
Page70 70 71 71 72 72 73 73 74 75 75

* Paper jams at the input sensor can be either after the paper leaves the tray and enters the printer or in the manual feeder.

Using the operator panel

Secondary Error codes

Page 56 of the Lexmark 230 user manual — Understanding the operator panel lights
Page 56 · click to enlarge
Page 56

Secondary Error codes (continued)

Lexmark 230 — Understanding the operator panel lights diagram (page 56)
Fig. 17 · Understanding the operator panel lights
Page76 76 77 77 78 79 80 81 81 82

Using the operator panel

Page 57 of the Lexmark 230 user manual — Primary codes
Page 57 · click to enlarge
Page 57

Operator panel codes

Below are explanations of what the primary light sequences, or codes, and secondary error codes mean and what you can do to clear them.

Primary codes

Ready / Power Saver

Lexmark 230 — Primary codes diagram (page 57)
Fig. 18 · Primary codes

Light sequence:

  • Ready—On

What this light sequence means:

  • The printer is ready to receive and process data.
  • The printer is in Power Saver mode.

What you can do:

  • Send a print job.
  • Press Continue to print the menu settings pages for a list of current printer settings.
  • Press and hold Cancel to reset the printer.

can only be set from the Local Printer Setup Utility (see “Using the Local Printer Setup Utility” on page 103).

Using the operator panel

Page 58 of the Lexmark 230 user manual — Busy
Page 58 · click to enlarge
Page 58

Busy

Lexmark 230 — Busy diagram (page 58)
Fig. 19 · Busy

Light sequence:

  • Ready—Blink

What this light sequence means:

  • The printer is busy receiving and processing data or printing.
  • The printer is defragmenting the flash memory to reclaim storage space occupied by deleted resources.
  • The printer is formatting the flash memory.
  • The printer is storing resources, such as fonts or macros, in flash memory.
  • The printer is printing a directory, font list, menu settings pages, or Print Quality Test Pages.

What you can do:

  • Busy: – Wait for the message to clear.

– Press and release Cancel to cancel the print job.

  • – Press and hold Cancel to reset the printer.
  • Defragmenting flash, formatting flash, or programming flash: – Wait for the message to clear. – Warning: Do not turn the printer off while this message is displayed.
  • Printing a directory, a font list, menu settings pages, or Print Quality Test Pages: – Wait for the pages to print. The Busy message is displayed as the pages print. The Ready light is on when printing stops.

– Press and release Cancel to cancel printing.

– Press and hold Cancel to reset the printer. • Receiving/processing data from a host interface: – Wait for the message to clear.

– Press and release Cancel to stop processing.

– Press and hold Cancel to reset the printer.

Using the operator panel

Page 59 of the Lexmark 230 user manual — Waiting
Page 59 · click to enlarge
Page 59

Hex Trace Ready

Lexmark 230 — Hex Trace Ready diagram (page 59)
Fig. 20 · Hex Trace Ready

Light sequence:

  • Ready—Slow blink

What this light sequence means:

The printer is in the Ready mode and Hex Trace is active.

What you can do:

  • Advanced users can use Hex Trace to help troubleshoot printing problems. After resolving the problem, turn off the printer to exit Hex Trace.
  • Press and hold Cancel to reset the printer.

Waiting

Lexmark 230 — Waiting diagram (page 59)
Fig. 21 · Waiting

Light sequence:

  • Continue—On
  • Ready—On

What this light sequence means:

The printer is waiting until a print timeout occurs, or until it receives additional data.

What you can do:

  • Press Continue to print the contents of the print buffer.
  • Press and release Cancel to cancel the print job.
  • Press and hold Cancel to reset the printer.

Using the operator panel

Page 60 of the Lexmark 230 user manual — Not ready
Page 60 · click to enlarge
Page 60

Flushing / Resolution reduced

Lexmark 230 — Flushing / Resolution reduced diagram (page 60)
Fig. 22 · Flushing / Resolution reduced

Light sequence:

  • Ready—Blink
  • Error—Blink

What this light sequence means:

  • The printer is flushing corrupted print data.
  • The printer is processing data or printing pages, but the resolution of a page in the current print job is reduced from 600 dots per inch (dpi) to 300 dpi to prevent a memory full error.

What you can do:

  • Wait until the operator panel returns to Ready to print other jobs.
  • Press and release Cancel to cancel the print job.
  • Press and hold Cancel to reset the printer.

Not ready

Lexmark 230 — Not ready diagram (page 60)
Fig. 23 · Not ready

Light sequence:

  • Continue—On

What this light sequence means:

The printer is not ready to receive or process data, or the printer ports are offline.

What you can do:

  • Press Continue to return to the Ready or Busy state.
  • Press and release Cancel to cancel the print job.
  • Press and hold Cancel to reset the printer.

Using the operator panel

Page 61 of the Lexmark 230 user manual — Load media
Page 61 · click to enlarge
Page 61

Close door

Lexmark 230 — Close door diagram (page 61)
Fig. 24 · Close door

Light sequence:

  • Error—On

What this light sequence means:

The printer door is open.

What you can do:

Close the door.

Load media

Lexmark 230 — Load media diagram (page 61)
Fig. 25 · Load media

Light sequence:

  • Continue—On
  • Load Paper—On

What this light sequence means:

The printer is out of media, or the media did not feed properly.

What you can do:

  • Load media into tray 1 or the optional 550-sheet tray and

press Continue to resume printing. • Check that the media is loaded correctly in tray 1 or the optional 550-sheet tray.

  • Press Cancel to cancel the print job.

Using the operator panel

Page 62 of the Lexmark 230 user manual — Print side two of a duplex job
Page 62 · click to enlarge
Page 62

Load manual feeder

Lexmark 230 — Load manual feeder diagram (page 62)
Fig. 26 · Load manual feeder

Light sequence:

  • Continue—On
  • Load Paper—Blink

What this light sequence means:

The printer prompts you to load a single sheet of media in the manual feed.

What you can do:

  • Load media, with the side to be printed facing the front of the printer, into the manual feed.
  • Press Continue to resume printing.
  • Press and hold Cancel to reset the printer.

Print side two of a duplex job

Lexmark 230 — Print side two of a duplex job diagram (page 62)
Fig. 27 · Print side two of a duplex job

Light sequence:

  • Continue—Blink
  • Load Paper—On

What this light sequence means:

Print the other side of your duplex print job.

What you can do:

  • Reinsert your print job in tray 1 using the instructions in the driver pop-up menu to orient the pages correctly. Press

Continue to resume printing.

  • Press and hold Cancel to reset the printer.

Using the operator panel

Page 63 of the Lexmark 230 user manual — Toner low
Page 63 · click to enlarge
Page 63

Invalid engine code / Invalid network code

Lexmark 230 — Invalid engine code / Invalid network code diagram (page 63)
Fig. 28 · Invalid engine code / Invalid network code

Light sequence:

  • Ready—On
  • Error—On

What this light sequence means:

The code in an internal print server has not been programmed, or the programmed code is not valid.

What you can do:

Download valid network code to the internal print server. Press

Continue twice quickly to see the secondary error code. See “Secondary error codes” on page 69 for more information.

Toner low

Lexmark 230 — Toner low diagram (page 63)
Fig. 29 · Toner low

Light sequence:

  • Toner Low/Replace PC Kit—On

What this light sequence means:

The printer is ready to receive and process data. In addition, the toner in the toner cartridge is getting low.

What you can do:

  • Press Continue to print the menu settings page for a list of current printer settings.
  • Remove the toner cartridge and shake it to extend the life of the cartridge.
  • Replace the toner cartridge. (See “How to change a toner cartridge” on page 108 for help.)
  • Press and hold Cancel to reset the printer.

cartridge is installed in a base printer model.

Using the operator panel

Page 64 of the Lexmark 230 user manual — Replace photoconductor kit
Page 64 · click to enlarge
Page 64

Photoconductor kit near full

Lexmark 230 — Photoconductor kit near full diagram (page 64)
Fig. 30 · Photoconductor kit near full

Light sequence:

  • Continue—On
  • Toner Low/Replace PC Kit—Blink

What this light sequence means:

The photoconductor kit’s drum is almost full and will need replacing soon.

for this message to appear.

What you can do:

  • Press Continue to resume printing.
  • Replace the photoconductor kit. See “How to change a photoconductor kit” on page 112 for more information.

Replace photoconductor kit

Lexmark 230 — Replace photoconductor kit diagram (page 64)
Fig. 31 · Replace photoconductor kit

Light sequence:

  • Toner Low/Replace PC Kit—Blink

What this light sequence means:

The photoconductor kit’s drum is full and needs replacing.

What you can do:

  • Press Continue to resume printing.
  • Replace the photoconductor kit. See “How to change a photoconductor kit” on page 112 for more information.

Using the operator panel

Page 65 of the Lexmark 230 user manual — Unsupported toner cartridge / Toner cartridge is not installed
Page 65 · click to enlarge
Page 65

Replace photoconductor kit (printer hard stop)

Lexmark 230 — Replace photoconductor kit (printer hard stop) diagram (page 65)
Fig. 32 · Replace photoconductor kit (printer hard stop)

Light sequence:

  • Continue—On
  • Toner Low/Replace PC Kit—Blink
  • Error—Blink

What this light sequence means:

The photoconductor kit’s drum is full and needs replacing. The printer will not print any more pages until the photoconductor kit is replaced.

What you can do:

Replace the photoconductor kit. (See “How to change a photoconductor kit” on page 112 for help.)

Unsupported toner cartridge / Toner cartridge is not installed

Lexmark 230 — Unsupported toner cartridge / Toner cartridge is not installed diagram (page 65)
Fig. 33 · Unsupported toner cartridge / Toner cartridge is not…

Light sequence:

  • Toner Low/Replace PC Kit—On
  • Error—On

What this light sequence means:

The toner cartridge is not installed, or the printer detects a toner cartridge error.

What you can do:

  • If the toner cartridge is not installed, install it.
  • If the toner cartridge is installed, remove it and install a new toner cartridge (see “How to change a toner cartridge” on page 108 ).

Using the operator panel

Page 66 of the Lexmark 230 user manual — Programming engine code / Programming system code
Page 66 · click to enlarge
Page 66

Change invalid toner cartridge

Lexmark 230 — Change invalid toner cartridge diagram (page 66)
Fig. 34 · Change invalid toner cartridge

Light sequence:

  • Toner Low/Replace PC Kit—On
  • Error—Blink

What this light sequence means:

The toner cartridge you are using was not designed for your printer.

What you can do:

Install a toner cartridge made for your printer (see “What supplies do I need and how do I order them?” on page 105).

Programming engine code / Programming system code

Lexmark 230 — Programming engine code / Programming system code diagram (page 66)
Fig. 35 · Programming engine code / Programming system code

Light sequence:

  • Ready—On
  • Toner Low/Replace PC Kit—On
  • Load Paper—On

What this light sequence means:

New code is being programmed into the engine or firmware code flash.

What you can do:

Wait for the message to clear. When the printer has finished programming the code, it performs a soft reset.

Using the operator panel

Page 67 of the Lexmark 230 user manual — Service error
Page 67 · click to enlarge
Page 67

Cancel job / Reset printer

Lexmark 230 — Cancel job / Reset printer diagram (page 67)
Fig. 36 · Cancel job / Reset printer

Light sequence:

  • Continue—On
  • Ready—On
  • Toner Low/Replace PC Kit—On
  • Load Paper—On
  • Paper Jam—On
  • Error—On

What this light sequence means:

  • The current print job is canceled.
  • The printer is resetting to the user default settings. Any active print jobs are canceled. A user default setting remains in effect until you change it or until you restore the factory default settings.

What you can do:

Wait for the message to clear.

Service error

Lexmark 230 — Service error diagram (page 67)
Fig. 37 · Service error

Light sequence:

  • Continue—Blink
  • Ready—Blink
  • Toner Low/Replace PC Kit—Blink
  • Load Paper—Blink
  • Paper Jam—Blink
  • Error—Blink

What this light sequence means:

The printer has a service error and printing has stopped.

What you can do:

Turn the printer off and back on. If the lights are still blinking, contact the place where you bought your printer.

Using the operator panel

Page 68 of the Lexmark 230 user manual — Paper jam printer error
Page 68 · click to enlarge
Page 68

Printer error

Lexmark 230 — Printer error diagram (page 68)
Fig. 38 · Printer error

Light sequence:

  • Continue—On
  • Error—On

What this light sequence means:

The printer has one of the following errors:

  • Memory is full, insufficient to save what is in the buffer, or insufficient to defragment flash memory.
  • A page is too complex to print or is shorter than the set page margins.
  • Resolution of a formatted page is reduced to 300 dpi.
  • A font error occurred.
  • Communication with the host computer is lost.

What you can do:

  • Press Continue twice quickly to see the secondary error code. See “Secondary error codes” on page 69 for more information.
  • Press Continue to clear the secondary message.

Paper jam printer error

Lexmark 230 — Paper jam printer error diagram (page 68)
Fig. 39 · Paper jam printer error

Light sequence:

  • Continue—On
  • Paper Jam—On

What this light sequence means:

The printer has a paper jam.

What you can do:

  • Press Continue twice quickly to see the secondary error code. See “Secondary error codes” on page 69 for more information.
  • Press Continue to resume printing once all the jammed pages are cleared from the paper path.

Using the operator panel

Page 69 of the Lexmark 230 user manual — Secondary error codes
Page 69 · click to enlarge
Page 69

Secondary error codes

  • When the Error and Continue lights are both on, a secondary error has occurred.
  • When the Paper Jam and Continue lights are both on, a paper jam secondary error has occurred.

Press and release Continue twice quickly to display the secondary error code light sequence.

Using the operator panel

Page 70 of the Lexmark 230 user manual — Paper jam in the manual feeder
Page 70 · click to enlarge
Page 70

Paper jam at the input sensor

Lexmark 230 — Paper jam at the input sensor diagram (page 70)
Fig. 40 · Paper jam at the input sensor

Light sequence:

  • Continue—On
  • Ready—On
  • Paper Jam—On

What this light sequence means:

A paper jam has occurred at the input sensor, which can be either after the paper leaves the tray and enters the printer or in the manual feeder.

What you can do:

Clear the paper jam. See “How to clear paper jams” on page 26 for more information.

Paper jam in the manual feeder

Lexmark 230 — Paper jam in the manual feeder diagram (page 70)
Fig. 41 · Paper jam in the manual feeder

Light sequence:

  • Continue—On
  • Ready—Blink
  • Paper Jam—On

What this light sequence means:

A paper jam has occurred in the manual feeder.

What you can do:

Clear the paper jam. See “How to clear paper jams” on page 26 for more information.

Using the operator panel

Page 71 of the Lexmark 230 user manual — Paper jams as a printed job exits the printer
Page 71 · click to enlarge
Page 71

Paper jams as it exits the tray into the printer

Lexmark 230 — Paper jams as it exits the tray into the printer diagram (page 71)
Fig. 42 · Paper jams as it exits the tray into the printer

Light sequence:

  • Continue—On
  • Toner Low/Replace PC Kit—On
  • Paper Jam—On

What this light sequence means:

A paper jam has occurred as the paper is exiting the paper tray and entering the printer.

What you can do:

Clear the paper jam. See “How to clear paper jams” on page 26 for more information.

Paper jams as a printed job exits the printer

Lexmark 230 — Paper jams as a printed job exits the printer diagram (page 71)
Fig. 43 · Paper jams as a printed job exits the printer

Light sequence:

  • Continue—On
  • Load Paper—On
  • Paper Jam—On

What this light sequence means:

A paper jam has occurred as the paper is exiting the printer.

What you can do:

Clear the paper jam. See “How to clear paper jams” on page 26 for more information.

Using the operator panel

Page 72 of the Lexmark 230 user manual — Paper jam in Tray 2
Page 72 · click to enlarge
Page 72

Paper jam in Tray 1

Lexmark 230 — Paper jam in Tray 1 diagram (page 72)
Fig. 44 · Paper jam in Tray 1

Light sequence:

  • Continue—On
  • Toner Low/Replace PC Kit—On
  • Load Paper—On
  • Paper Jam—On

What this light sequence means:

A paper jam has occurred in Tray 1.

What you can do:

Clear the paper jam. See “How to clear paper jams” on page 26 for more information.

Paper jam in Tray 2

Lexmark 230 — Paper jam in Tray 2 diagram (page 72)
Fig. 45 · Paper jam in Tray 2

Light sequence:

  • Continue—On
  • Ready—On
  • Load Paper—On
  • Paper Jam—On

What this light sequence means:

A paper jam has occurred in Tray 2.

What you can do:

Clear the paper jam. See “How to clear paper jams” on page 26 for more information.

Using the operator panel

Page 73 of the Lexmark 230 user manual — Insufficient printer memory
Page 73 · click to enlarge
Page 73

Complex page

Lexmark 230 — Complex page diagram (page 73)
Fig. 46 · Complex page

Light sequence:

  • Continue—On
  • Ready—On
  • Error—On

What this light sequence means:

The page may not print correctly because the print information on the page is too complex (that is, too large for the printer’s memory).

What you can do:

  • Press Continue to clear the message and continue processing the print job (some of the print data may be lost).
  • To avoid this error in the future: – Reduce the complexity of the page by reducing the amount of text or graphics on the page and deleting unnecessary downloaded fonts or macros. – Set Page Protect to On in the Local Printer Setup Utility. – Install additional printer memory (see “How to add a memory card” on page 45 ).

Insufficient printer memory

Lexmark 230 — Insufficient printer memory diagram (page 73)
Fig. 47 · Insufficient printer memory

Light sequence:

  • Continue—On
  • Ready—Blink
  • Error—On

What this light sequence means:

The printer does not have enough memory to save the data in the buffer.

What you can do:

  • Install additional memory (see “How to add a memory card” on page 45 ).
  • Press Continue to continue printing the job.
  • Press Cancel to cancel the print job.

Using the operator panel

Page 74 of the Lexmark 230 user manual — Insufficient collation area
Page 74 · click to enlarge
Page 74

Insufficient collation area

Lexmark 230 — Insufficient collation area diagram (page 74)
Fig. 48 · Insufficient collation area

Light sequence:

  • Continue—On
  • Toner Low/Replace PC Kit—On
  • Error—On

What this light sequence means:

The printer memory does not have the free space necessary to collate the print job. This may happen due to one of these errors:

  • Memory is full.
  • A page is too complex to print.
  • A page is shorter than the set page margins.
  • Memory is insufficient to save what is in the buffer.

What you can do:

  • Press Continue to clear the message and continue printing the job (the job may not print correctly.)
  • Press and release Cancel to cancel the print job.
  • Press and hold Cancel to reset the printer.
  • To avoid this error in the future: – Simplify the print job. Reduce the complexity of the page by reducing the amount of text or graphics on the page and deleting unnecessary downloaded fonts or macros. – Install additional printer memory (see “How to add a memory card” on page 45 ).

Using the operator panel

Page 75 of the Lexmark 230 user manual — Defective flash
Page 75 · click to enlarge
Page 75

Font error

Lexmark 230 — Font error diagram (page 75)
Fig. 49 · Font error

Light sequence:

  • Continue—On
  • Toner Low/Replace PC Kit—Blink
  • Error—On

What this light sequence means:

The printer has received a request for a PPDS font which is not installed.

What you can do:

  • Press and release Cancel to cancel the print job.
  • Press and hold Cancel to reset the printer.
  • Press Continue to clear the message and continue printing.

Defective flash

Lexmark 230 — Defective flash diagram (page 75)
Fig. 50 · Defective flash

Light sequence:

  • Continue—On
  • Load Paper—On
  • Error—On

What this light sequence means:

The printer detects defective flash memory.

What you can do:

  • Press Continue to clear the message and continue printing. Downloaded fonts and macros not previously stored in flash memory are deleted.
  • See “How to add a memory card” on page 45 to install flash memory.

Using the operator panel

Page 76 of the Lexmark 230 user manual — Network interface errors
Page 76 · click to enlarge
Page 76

Insufficient defrag memory

Lexmark 230 — Insufficient defrag memory diagram (page 76)
Fig. 51 · Insufficient defrag memory

Light sequence:

  • Continue—On
  • Load Paper—Blink
  • Error—On

What this light sequence means:

The printer has insufficient memory to free unused space in flash memory.

What you can do:

  • Delete fonts, macros, and other data in RAM.
  • Install additional printer memory.

Network interface errors

Lexmark 230 — Network interface errors diagram (page 76)
Fig. 52 · Network interface errors

Light sequence:

  • Continue—On
  • Paper Jam—On
  • Error—On

What this light sequence means:

The printer cannot establish communication with the network.

What you can do:

Press Continue to clear the message and continue printing. (The job may not print correctly.)

Using the operator panel

Page 77 of the Lexmark 230 user manual — Host interface disabled
Page 77 · click to enlarge
Page 77

Error communicating with the host computer

Lexmark 230 — Error communicating with the host computer diagram (page 77)
Fig. 53 · Error communicating with the host computer

Light sequence:

  • Continue—On
  • Paper Jam—Blink
  • Error—On

What this light sequence means:

The printer has lost the connection to an external print server (also called an external network adapter or ENA).

This light sequence is displayed if your printer is connected to the network, but it cannot detect the print server when you turn on the printer.

What you can do:

  • Make sure the cable connecting the ENA and the printer is securely attached. Turn the printer off and then on to reset the printer.
  • Press and hold Cancel to reset the printer.

Host interface disabled

Lexmark 230 — Host interface disabled diagram (page 77)
Fig. 54 · Host interface disabled

Light sequence:

  • Continue—On
  • Load Paper—Blink
  • Paper Jam—Blink
  • Error—On

What this light sequence means:

The printer USB or parallel port has been disabled.

What you can do:

  • Press Continue to clear the message. The printer discards any print jobs previously sent. Enable the USB or parallel port by selecting a value other than Disabled for the USB Buffer or Parallel Buffer item in the Local Printer Setup Utility (see Using the Local Printer Setup Utility ).

Using the operator panel

Page 78 of the Lexmark 230 user manual — Memory full
Page 78 · click to enlarge
Page 78

Memory full

Lexmark 230 — Memory full diagram (page 78)
Fig. 55 · Memory full

Light sequence:

  • Continue—On
  • Ready—On
  • Toner Low/Replace PC Kit—On
  • Error—On

What this light sequence means:

The printer is processing data, but the memory used to store pages is full.

What you can do:

  • Press Continue to clear the message and continue printing the job (the job may not print correctly).
  • Press and release Cancel to cancel the print job.
  • Press and hold Cancel to reset the printer.
  • To avoid this error in the future: – Simplify the print job. Reduce the complexity of the page by reducing the amount of text or graphics on the page and deleting unnecessary downloaded fonts or macros. – Install additional printer memory (see “How to add a memory card” on page 45 ).

Using the operator panel

Page 79 of the Lexmark 230 user manual — Short paper
Page 79 · click to enlarge
Page 79

Short paper

Lexmark 230 — Short paper diagram (page 79)
Fig. 56 · Short paper

Light sequence:

  • Continue—On
  • Ready—On
  • Load Paper—On
  • Error—On

What this light sequence means:

The paper length is too short to print the formatted data. This occurs when the printer does not know the media size loaded in the tray, or there is a problem feeding the media.

What you can do:

  • Make sure the print media you loaded is large enough.
  • Open the front cover, clear the paper path and close the cover to resume printing (see “How to clear paper jams” on page 26 ).
  • Press Continue to clear the message and continue printing the job.
  • Press Cancel to cancel the print job.

Using the operator panel

Page 80 of the Lexmark 230 user manual — Flash full
Page 80 · click to enlarge
Page 80

Flash full

Lexmark 230 — Flash full diagram (page 80)
Fig. 57 · Flash full

Light sequence:

  • Continue—On
  • Ready—On
  • Paper Jam—On
  • Error—On

What this light sequence means:

There is not enough free space in the flash memory to store the data you are trying to download.

What you can do:

  • Delete fonts, macros, and other data stored on the flash memory to free up space.
  • Press Continue to clear the message and continue printing. Downloaded fonts and macros not previously stored in flash memory are deleted.
  • Install flash memory with more storage capacity. See “How to add a memory card” on page 45 for instructions on how to install flash memory.
  • Press and release Cancel to cancel the print job.
  • Press and hold Cancel to reset the printer.

Using the operator panel

Page 81 of the Lexmark 230 user manual — Invalid engine code
Page 81 · click to enlarge
Page 81

Unformatted flash

Lexmark 230 — Unformatted flash diagram (page 81)
Fig. 58 · Unformatted flash

Light sequence:

  • Continue—On
  • Toner Low/Replace PC Kit—On
  • Paper Jam—On
  • Error—On

What this light sequence means:

The printer detects unformatted flash memory.

What you can do:

  • Press Continue to clear the message and continue printing. The job may not print correctly.
  • Reformat the flash memory. Refer to the Technical Reference on Lexmark’s Web site for more information about reformatting flash.
  • If the error message remains, the flash memory may be defective and should be replaced.

Invalid engine code

Lexmark 230 — Invalid engine code diagram (page 81)
Fig. 59 · Invalid engine code

Light sequence:

  • Ready—On
  • Load Paper—On
  • Error—On

What this light sequence means:

The code in an internal print server has not been programmed, or the programmed code is not valid.

What you can do:

Download valid engine code to the internal print server.

Using the operator panel

Page 82 of the Lexmark 230 user manual — Invalid network code
Page 82 · click to enlarge
Page 82

Invalid network code

Lexmark 230 — Invalid network code diagram (page 82)
Fig. 60 · Invalid network code

Light sequence:

  • Ready—On
  • Load Paper—Blink
  • Error—On

What this light sequence means:

The code in an internal print server has not been programmed, or the programmed code is not valid.

What you can do:

Download valid network code to the internal print server.

Using the operator panel

Page 83 of the Lexmark 230 user manual — Printing the Printer Settings Configuration sheet
Page 83 · click to enlarge
Page 83

6 Understanding the printer configuration menus

Printing the Printer Settings Configuration sheet 83

Configuration menus overview 84

  • Network menu 85
  • Parallel menu 86
  • Setup menu 86
  • USB menu 87
  • Utilities menu 87

Printing the Printer Settings Configuration sheet

To help resolve printing problems or to change printer configuration settings, advanced users can print the Printer Settings Configuration sheet for instructions on advancing through the configuration menus to select and save new settings.

To print the Printer Settings Configuration sheet:

1 Turn off the printer.

2 Open the front cover.

3 Press and hold Continue as you turn the printer back on.

All the lights cycle.

4 Close the cover. The light sequence that represents the Home menu is displayed.

5 To print the Printer Settings Configuration sheet, press and hold Continue until the lights cycle. The sheet prints.

Understanding the printer configuration menus

Section Page

Page 84 of the Lexmark 230 user manual — Configuration menus overview
Page 84 · click to enlarge
Page 84

Configuration menus overview

Menus are represented by Ready, Toner Low/Replace PC Kit, Load Paper, and

Paper Jam light sequences. Menu items and their settings are indicated by Error and

Continue light sequences.

  • Press and release Cancel to advance through menus and menu items.
  • Press and release Continue to advance to the setting you need.
  • Press and hold Continue until all of the lights cycle to save a setting.
  • Press and hold Cancel until all of the lights cycle to return to the Home menu.
  • Turn off the printer to exit the menus.

Understanding the printer configuration menus

Page 85 of the Lexmark 230 user manual — Network menu
Page 85 · click to enlarge
Page 85

Network menu

Use the Network menu to change printer settings on jobs sent through a network port (either Standard Network or Network Opt ).

Setting Use this setting toValues

NPA Mode Send print jobs to the printer and query printer status information simultaneously.

  • Off
  • Auto *

MAC Binary PS Configure the printer to process Macintosh binary PostScript print jobs.

  • Off —The printer filters PostScript print jobs using standard protocol.
  • On —The printer processes raw binary PostScript print jobs from computers using the Macintosh operating system. This setting often causes Windows print jobs to fail.
  • Auto *—The printer processes print jobs from computers using either Windows or Macintosh operating systems.

Set Card Speed Automatically detect the connection speed of your network. You can disable this setting to set the speed manually.

  • Auto *—The printer detects current network speed.
  • 10Mbps † , Half Duplex —Forces the printer to try to connect to the network only at 10Mbps, Half Duplex.
  • 10Mbps, Full Duplex —Forces the printer to try to connect to the network only at 10Mbps, Full Duplex.
  • 100Mbps, Half Duplex —Forces the printer to try to connect to the network only at 100Mbps, Half Duplex.
  • 100Mbps, Full Duplex —Forces the printer to try to connect to the network only at 100Mbps, Full Duplex.

† Megabits per second

Understanding the printer configuration menus

* Factory default

Page 86 of the Lexmark 230 user manual — Setup menu
Page 86 · click to enlarge
Page 86

Parallel menu

Use the Parallel menu to change printer settings on jobs sent through a parallel port.

Setting Use this setting toValues

NPA Mode Send print jobs to the printer and query printer status information simultaneously.

  • Off
  • On
  • Auto *

Protocol Receive information at a much higher transmission rate if your printer is set to Fastbytes (if your computer supports Fastbytes) or receive information at a normal transmission rate if your printer is set to Standard.

  • Standard
  • Fastbytes *

Parallel Mode 2 Determine whether the parallel port data is sampled on the leading (On) or trailing (Off) edge of strobe.

  • Off
  • On *

MAC Binary PS Configure the printer to process Macintosh binary PostScript print jobs.

  • Off —The printer filters PostScript print jobs using standard protocol.
  • On —The printer processes raw binary PostScript print jobs from computers using the Macintosh operating system. This setting often causes Windows print jobs to fail.
  • Auto *—The printer processes print jobs from computers using either Windows or Macintosh operating systems.

Setup menu

Use the Setup menu to configure how the printer formats the end of a line depending on the computer system being used.

Setting Use this setting toValues

Auto CR after LF Specify whether the printer automatically performs a carriage return after a line feed control command.

  • Off *
  • On

Auto LF after CR Specify whether the printer automatically performs a line feed after a carriage return control command.

  • Off *
  • On

Understanding the printer configuration menus

* Factory default · * Factory default

Page 87 of the Lexmark 230 user manual — Utilities menu
Page 87 · click to enlarge
Page 87

USB menu

Use the USB menu to change printer settings on jobs sent through a Universal Serial Bus (USB) port.

Setting Use this setting toValues

NPA Mode Send print jobs to the printer and query printer status information simultaneously.

  • Off
  • On
  • Auto *

MAC Binary PS Configure the printer to process Macintosh binary PostScript print jobs.

  • Off —The printer filters PostScript print jobs using standard protocol.
  • On —The printer processes raw binary PostScript print jobs from computers using the Macintosh operating system. This setting often causes Windows print jobs to fail.
  • Auto *—The printer processes print jobs from computers using either Windows or Macintosh operating systems.

Utilities menu

Use the Utilities menu to troubleshoot printer problems.

Setting Use this setting toValues

Return your printer settings to the factory default values. Sometimes resetting the printer to the original settings solves formatting problems. All menu items are reset to the factory default values except:

  • Display Language.
  • All settings in the Parallel menu, Network menu, LocalTalk menu, and USB menu.

All downloaded resources (fonts, macros, and symbol sets) in printer memory (RAM) are deleted. Resources in flash memory are unaffected.

Return the photoconductor counter to zero.

The replace photoconductor message should be cleared only when the photoconductor kit has been replaced.

Hex Trace Help isolate printing problems when unexpected characters print or characters are missing. Hex Trace helps you determine if there is a problem with the language interpreter or the cable by telling you what information your printer is receiving. To exit Hex Trace, turn off the printer.

  • Off *
  • On

Print Quality Test Pages

Help isolate print quality problems, such as streaking. When you select this setting, three pages print to help you evaluate print quality:

  • A text page with printer information, cartridge information, current margin settings, and a graphic.
  • Two pages with graphics.

Understanding the printer configuration menus

Show 4 more labels / short text on this page
* Factory default · Reset Factory Defaults · Reset Photoconductor Counter · * Factory default
Page 88 of the Lexmark 230 user manual — 7 Software and network tasks
Page 88 · click to enlarge
Page 88

7 Software and network tasks

How to install drivers for local printing 89

How to print the menu settings and network setup pages 94

How to print a test page 94

How to configure for TCP/IP 95

How to set up the printer for network printing 96

Using the printer resident Web page 102

Using the Local Printer Setup Utility 103

Software and network tasks

Section Page

Page 89 of the Lexmark 230 user manual — Using Windows Server 2003, Windows 2000, Windows XP, and Windows 98/Me
Page 89 · click to enlarge
Page 89

How to install drivers for local printing

A local printer is a printer attached to your computer using a USB or parallel cable. The printer driver is software that lets your computer communicate with your printer.

The procedure to install drivers depends on the operating system you are using. Use the following table to find driver installation instructions for your particular operating system. If you need additional help, refer to the documentation that shipped with your computer and your software.

Operating system Go to page...

Windows

Some Windows operating systems may already include a printer driver that is compatible with your printer. This may mean that installation will seem automatic in later versions of Windows. System printer drivers work well for simple printing, but they contain less functionality than our enhanced custom printer driver.

Installing a custom driver does not replace the system driver. A separate printer object is created and appears in the Printers folder.

Use the drivers CD that shipped with your printer to install the custom printer driver and obtain all the enhanced printer features and functionality.

Drivers are also available in downloadable software packages on our Lexmark Web site at www.lexmark.com.

Using Windows Server 2003, Windows 2000, Windows XP, and Windows 98/Me

1 Insert the drivers CD.

If the CD does not auto launch, click Start Æ Run, and then type D:\Setup.exe in the Run dialog box.

2 Click Install Software.

install printer drivers on your computer.

3 Click Printer and Software.

4 Click Agree to accept the license agreement.

5 Select Suggested, and then click Next.

6 Select Local Attached, and then click Next.

Software and network tasks

Windows 89 · Macintosh 91 · UNIX/Linux 93

Page 90 of the Lexmark 230 user manual — Using Windows 95, Windows NT
Page 90 · click to enlarge
Page 90

7 Follow the instructions on your screen to complete installing the drivers.

Using Windows 95, Windows NT

1 Insert the drivers CD.

If the CD does not auto launch, click Start Æ Run, and then type D:\Setup.exe in the Run dialog box.

2 Click Install Software.

3 Click Printer and Software.

4 Click Agree to accept the license agreement.

5 Select Custom, and then click Next.

6 Follow the instructions on your screen to complete installing the drivers.

Software and network tasks

Page 91 of the Lexmark 230 user manual — Creating a desktop printer icon (Macintosh 8.6–9.x)
Page 91 · click to enlarge
Page 91

Macintosh

Macintosh OS 8.6 or later is required for USB printing. To print locally to a USB-attached printer, you must create a desktop printer icon (Macintosh 8.6–9.x) or create a queue in Print Center (Macintosh OS X).

Creating a desktop printer icon (Macintosh 8.6–9.x)

1 Install a printer PostScript Printer Description (PPD) file on your computer.

a Insert the drivers CD.

b Double-click Classic, and then double-click the installer package for your printer.

Macintosh computer.

c Choose the language you want to use, and then click OK.

d Click Accept after you read the license agreement.

e Click Continue after you finish with the Readme file.

f Choose a default paper size.

g On the Easy Install screen, click Install. All the necessary files are installed on your computer.

h Click Quit when installation is complete.

Lexmark Web site at www.lexmark.com.

2 Do one of the following:

Macintosh 8.6–9.0: Open Apple LaserWriter.

Macintosh 9.1–9.x: Open Applications, and then click Utilities.

3 Double-click Desktop Printer Utility.

4 Select Printer (USB), and then click OK.

5 In the USB Printer Selection section, click Change.

If your printer does not appear in the USB Printer Selection list, make sure the USB cable is properly connected and the printer is turned on.

6 Select the name of your printer, and then click OK. Your printer appears in the original Printer (USB) window.

7 In the PostScript Printer Description (PPD) File section, click Auto Setup. Make sure your printer PPD now matches your printer.

Software and network tasks

Page 92 of the Lexmark 230 user manual — Creating a queue in Print Center (Macintosh OS X)
Page 92 · click to enlarge
Page 92

8 Click Create, and then click Save.

9 Specify a printer name, and then click Save. Your printer is now saved as a desktop printer.

Creating a queue in Print Center (Macintosh OS X)

1 Install a printer PostScript Printer Description (PPD) file on your computer.

a Insert the drivers CD.

b Double-click Mac OS X, and then double-click the installer package for your printer.

Macintosh computer.

c On the Authorization screen, choose Click the lock to make changes.

d Enter your password, and then click OK.

e Click Continue on the Welcome screen and again after you view the Readme file.

f Click Agree to accept the license agreement.

g Select a Destination, and then click Continue.

h On the Easy Install screen, click Install. All the necessary files are installed on your computer.

i Click Close when installation is complete.

2 Open Finder, click Applications, and then click Utilities.

3 Double-click Print Center.

Lexmark Web site at www.lexmark.com.

4 Do one of the following:

If your USB-attached printer appears in the Printer List, you can quit Print Center. A queue has been created for your printer.

If your USB-attached printer does not appear in the Printer List, make sure the USB cable is properly connected and the printer is turned on. After the printer appears in the Printer List, you can quit Print Center.

Software and network tasks

Page 93 of the Lexmark 230 user manual — UNIX/Linux
Page 93 · click to enlarge
Page 93

UNIX/Linux

Local printing is supported on many UNIX and Linux platforms, such as Sun Solaris and Red Hat.

The Sun Solaris and Linux packages are available on the drivers CD and on our Lexmark Web site at www.lexmark.com. The User’s Guide in each package gives detailed instructions for installing and using Lexmark printers in UNIX and Linux environments.

All the printer driver packages support local printing using a parallel connection. The driver package for Sun Solaris supports USB connections to Sun Ray appliances and Sun workstations.

Visit our Lexmark Web site at www.lexmark.com for a complete list of supported UNIX and Linux platforms.

Software and network tasks

Page 94 of the Lexmark 230 user manual — Macintosh
Page 94 · click to enlarge
Page 94

How to print the menu settings and network setup pages

To print the menu settings page and network setup page, press the Continue button from the Ready state.

  • On the menu settings page:

– Verify that the options you installed are correctly listed under “Installed Features.”

If an option is not listed under Installed Features, turn off the printer, unplug the power cord, and reinstall the option.

– Verify the amount of memory installed is correctly listed under “Printer Information.” – Verify that the paper trays are configured for the sizes and types of paper you loaded.

  • On the network setup page, confirm that Status is “Connected.”

If Status is “Not Connected,” your LAN drop may not be active or your network cable may be malfunctioning. Consult your network support person for a solution, and then print another network setup page to verify that you are connected to your network.

How to print a test page

Windows

1 Click Start Æ Settings Æ Printers.

2 Select your printer.

3 Click File Æ Properties.

4 Click Print Test Page.

Macintosh

1 From the desktop, double-click your printer icon.

2 Double-click <printer name> Utility.

3 Click the Print a Test Page button.

Software and network tasks

Page 95 of the Lexmark 230 user manual — Verifying the IP settings
Page 95 · click to enlarge
Page 95

How to configure for TCP/IP

If you have TCP/IP available on your network, we recommend that you assign an IP address to the printer.

Assigning a printer IP address

If your network is using DHCP, an IP address is automatically assigned after you connect the network cable to the printer.

1 Look for the address under the “TCP/IP” heading on the network setup page you printed in “How to print the menu settings and network setup pages” on page 94.

2 Go to “Verifying the IP settings” on page 95 and begin with step 2.

If your network is not using DHCP, then you must manually assign an IP address to the printer.

An easy way to do this is to use the Print Server TCP/IP Setup Utility.

Detailed instructions about installing and using this utility are located on the drivers CD that shipped with your printer. Launch the CD, click View Documentation and then Network Printer Install. Look for information about using the Print Server TCP/IP Setup Utility.

To use this utility, you will need to know the printer’s 12-digit physical address or Universally Administered Address (UAA). Look for the UAA entry on the network setup page you printed earlier. You can use either the MSB or canonical form of the UAA.

Verifying the IP settings

1 Print another network setup page. Look under the “TCP/IP” heading and make sure the IP address, netmask, and gateway are what you expected.

See “How to print the menu settings and network setup pages” on page 94 if you need help.

Command prompt (or Accessories Æ Command prompt if using Windows 2000).

2 Ping the printer and verify that it responds. For example, at a command prompt on a network computer type ping followed by the new printer IP address (for example, 192.168.0.11):

If the printer is active on the network, you will receive a confirmation.

Software and network tasks

Page 96 of the Lexmark 230 user manual — Windows
Page 96 · click to enlarge
Page 96

How to set up the printer for network printing

After you have assigned and verified the TCP/IP settings (see “How to configure for TCP/IP” on page 95), you are ready to install the printer drivers on each network computer.

Windows

In Windows environments, network printers can be configured for direct printing or shared printing. Both network printing methods require the installation of a printer driver and the creation of a network printer port.

  • Windows system printer driver
  • Lexmark custom printer driver

System drivers are built into Windows operating systems. Custom drivers are available on the drivers CD.

Updated system and custom drivers are available on our Lexmark Web site at www.lexmark.com.

Supported network printer ports

  • Microsoft IP port—Windows NT 4.0, Windows 2000, Windows XP, and Windows Server 2003
  • Lexmark network port—Windows 95/98/Me, Windows NT 4.0, Windows 2000, Windows XP, and Windows Server 2003

For basic printer functionality, you can install a system printer driver and use a system network printer port, such as an LPR or a Standard TCP/IP port. The system printer driver and port let you maintain a consistent user interface for use with all the printers on your network. However, using a custom printer driver and network port provides enhanced functionality, such as printer status alerts.

Follow the steps for your printing configuration and operating system to configure your network printer:

Printing configuration Operating system Go to page...

Windows 95/98/Me, Windows NT 4.0, Windows 2000, Windows XP, or Windows Server 2003

Printer is connected directly to the network using a network cable, such as Ethernet.

Printer drivers are typically installed on each network computer.

Windows NT 4.0, Windows 2000, Windows XP, or Windows Server 2003

Printer is connected to one of the computers on the network using a local cable, such as USB.

Printer drivers are installed on the computer attached to the printer.

During driver installation, the printer is set up to be “shared” so that other network computers can print to it.

Software and network tasks

Supported printer drivers · Direct · Shared

Page 97 of the Lexmark 230 user manual — How to set up the printer for network printing
Page 97 · click to enlarge
Page 97

Direct printing using Windows 95/98,Me, Windows NT 4.0, Windows 2000, Windows XP, and Windows Server 2003

To install a custom printer driver and network port:

1 Launch the drivers CD.

2 Click Install Printer and Software.

3 Click Printer.

4 Click Agree to accept the license agreement.

5 Select Quick install, and then click Next.

6 Click Create new port.

7 Click Add Port.

8 Select Lexmark TCP/IP Network Port, and then click Add.

9 Enter the information to create the port.

a Assign a logical port name.

This can be any name that you associate with the printer, such as Color1-lab4. After the port is created, this name appears in the list of available ports on the Method of Connection screen.

TCP/IP heading. For help, see “How to print the menu settings and network setup pages” on page 94.

b Enter the IP address in the text box.

c Click Add Port.

10 Click Done until you return to the Method of Connection screen.

11 Select the newly-created port from the list, and then select the model of the printer you want to install.

12 Click Finish to complete the installation.

13 Print a test page to verify printer installation (see “How to print a test page” on page 94).

Shared printing from a server using Windows NT 4.0, Windows 2000, Windows XP, and Windows Server 2003

After connecting your printer to a Windows NT 4.0, Windows 2000, Windows XP, or Windows Server 2003 computer (which will act as a server), follow these steps to configure your network printer for shared printing:

Software and network tasks

Page 98 of the Lexmark 230 user manual — How to set up the printer for network printing
Page 98 · click to enlarge
Page 98
1. Install a custom printer driver

1 Insert the drivers CD.

If the CD does not auto launch, click Start Æ Run, and then type D:\Setup.exe in the Run dialog box.

2 Click Install Software.

3 Click Printer and Software.

4 Click Agree to accept the license agreement.

5 Select Suggested, and then click Next.

6 Select Local Attached, and then click Next.

7 Follow the instructions on your screen to complete installing the drivers.

8 Print a test page to verify printer installation (see “How to print a test page” on page 94).

2. Share the printer on the network

1 Click Start Æ Settings Æ Printers.

2 Select the printer you just created.

3 Click File Æ Sharing.

4 Check the Shared check box, and then enter a name in the Shared Name text box.

5 In the Alternate Drivers section, select the operating systems of all the network clients that will print to the printer.

6 Click OK.

system CD.

7 Check the following to make sure the printer was successfully shared.

  • The printer object in the Printers folder now has a shared indicator. For example, in Windows NT 4.0, a hand appears under the printer object.
  • Browse Network Neighborhood. Find the host name of the server and look for the shared name you assigned to the printer.
3. Install the printer driver (or subset) on network clients

Using the point and print method

modifications and the print job processing. This lets network clients return to programs much faster.

Software and network tasks

Page 99 of the Lexmark 230 user manual — How to set up the printer for network printing
Page 99 · click to enlarge
Page 99

With this method, a subset of driver information is copied from the server to the client computer. This is just enough information to send a print job to the printer.

1 On the Windows desktop of the client computer, double-click Network Neighborhood.

2 Locate the host name of the server computer, and then double-click the host name.

3 Right-click the shared printer name, and then click Install.

4 Wait a few minutes for the driver information to be copied from the server computer to the client computer, and for a new printer object to be added to the Printers folder. The time this takes varies based on network traffic and other factors.

5 Close Network Neighborhood.

6 Print a test page to verify printer installation (see “How to print a test page” on page 94).

Using the peer-to-peer method

With this method, the printer driver is fully installed on each client computer. Network clients retain control of driver modifications. The client computer handles the print job processing.

1 Click Start Æ Settings Æ Printers.

2 Click Add Printer to launch the Add Printer wizard.

3 Click Network Print Server.

4 Select the network printer from the Shared printers list. If the printer is not listed, enter the path of the printer in the text box.

The path will look similar to the following:

\\<server host name>\<shared printer name>

driver is available, then you need to provide a path to available drivers.

The server host name is the name of the server computer that identifies it to the network. The shared printer name is the name assigned during the server installation process.

5 Click OK.

6 Select whether you want this printer to be the default printer for the client, and then click Finish.

7 Print a test page to verify printer installation (see “How to print a test page” on page 94).

Software and network tasks

Page 100 of the Lexmark 230 user manual — Mac OS 8.6 to 9.x
Page 100 · click to enlarge
Page 100

Macintosh

capabilities of a printer to your UNIX or Macintosh computers.

To print to a network printer, each Macintosh user must install a custom PostScript Printer Description (PPD) file and either create a desktop printer on the computer (Mac OS 8.6 to 9.x) or create a print queue in Print Center (Mac OS X). Follow the instructions for your operating system.

Mac OS 8.6 to 9.x

1. Install a custom PPD file

set up. If the printer was previously installed, go on to Step 2: Create a desktop printer.

1 Insert the drivers CD.

2 Double-click Classic.

3 Double-click the Lexmark Installer icon.

4 Select the language of your operating system, and then click OK.

5 Click Install to install the PPD file for your printer.

2. Create a desktop printer

1 In the Chooser, select the LaserWriter 8 driver.

2 If you have a routed network, select the default zone from the list. If you don’t know which zone to select, look on the Network Setup page under AppleTalk for Zone.

3 Select the new printer from the list.

4 If you don’t know which printer to select, look on the Network Setup page under the AppleTalk heading to find the default name of the printer.

5 Click Create.

6 Make sure there is an icon next to the printer name in the Chooser.

7 Close the Chooser window.

8 Verify printer installation.

a Click the desktop printer icon you just created.

b Choose Printing Æ Change Setup.

Software and network tasks

Page 101 of the Lexmark 230 user manual — Mac OS X version 10.1.2 and later
Page 101 · click to enlarge
Page 101
  • If the PPD file displayed in the PostScript Printer Description (PPD) file portion of the menu is correct for your printer, then printer setup is complete.
  • If the PPD file displayed in the PostScript Printer Description (PPD) file portion of the menu is not correct for your printer, repeat “Step 1: Install a custom PPD file” on page 100 .

Mac OS X version 10.1.2 and later

1. Install a custom PPD file

1 Insert the drivers CD.

2 Click Mac OS X Æ <language>.

For example, Mac OS X Æ English.

3 Double-click the installer icon for your printer to run the installer.

2. Create a print queue in Print Center

1 Click Applications Æ Utilities Æ Print Center.

2 Click Add Printer.

3 Choose AppleTalk as your method of connection.

4 If you have a routed network, select the zone from the list. If you don’t know which zone to select, look on the Network Setup page under AppleTalk for Zone.

5 Select the new printer from the list, and then click Add.

AppleTalk heading to find the default name of the printer.

6 Verify printer installation:

a Click Applications Æ TextEdit.

b Choose File Æ Print Æ Summary. The Summary window shows the PPD installed for your printer.

  • If the PPD file displayed in the Summary window is correct for your printer, then printer setup is complete.
  • If the PPD file displayed in the Summary window is not correct for your printer, delete the print queue from Print Center and repeat Step 1: Install a custom PPD file .

Software and network tasks

Page 102 of the Lexmark 230 user manual — Using the printer resident Web page
Page 102 · click to enlarge
Page 102

UNIX/Linux

Your printer supports many UNIX and Linux platforms, such as Sun Solaris and Red Hat. Visit our Lexmark Web site at www.lexmark.com for a complete list of supported UNIX and Linux platforms.

Lexmark Web site at www.lexmark.com.

Lexmark provides a printer driver package for each supported UNIX and Linux platform. The User’s Guide in each package gives detailed instructions for installing and using Lexmark printers in UNIX and Linux environments.

You can download these packages from our Lexmark Web site. You may also find the driver package you need on the drivers CD.

NetWare

Your printer supports both Novell Distributed Print Services (NDPS) and regular queue-based NetWare environments. For the latest information about installing a network printer in a NetWare environment, launch the drivers CD and click View Documentation.

Using the printer resident Web page

If you have a network model, your printer has a resident Web page, which you can access from your browser. To access the resident Web page, type the printer’s IP address in the URL address field of your browser (for example, http://192.168.236.24). If you do not know the IP address of your printer, you can find it on the network setup page (for help, see “How to print the menu settings and network setup pages” on page 94).

Some of the resident Web page features include a real-time status window of the printer and details of the printer’s configuration, such as current memory and engine code levels. If you have administrative rights, you can also change printer settings.

Software and network tasks

Page 103 of the Lexmark 230 user manual — Using the Local Printer Setup Utility
Page 103 · click to enlarge
Page 103

Using the Local Printer Setup Utility

The Local Printer Setup Utility, located on the drivers CD, lets you change printer settings not available from your printer driver (for example, activating Alarm Control if you want the printer to sound an alarm when it needs attention).

Click View Documentation on the drivers CD for instructions on installing and using the Local Printer Setup Utility on your computer.

You can change the following settings using the Local Printer Setup Utility:

Finishing Settings Paper Settings Parallel Settings PCL Emulation Settings

  • Duplex
  • Duplex Bind
  • Copies
  • Blank Pages
  • Collation
  • Separator Sheets
  • Separator Source
  • Multipage Print
  • Multipage Order
  • Multipage View
  • Multipage Border
  • Paper Source
  • PCL SmartSwitch
  • PS SmartSwitch
  • Parallel Buffer
  • Advanced Status
  • Honor Init
  • Orientation
  • Lines Per Page
  • A4 Width
  • Paper Size *
  • Paper Type *
  • Tray Renumber *
  • Custom Types †
  • Auto CR after LF
  • Auto LF after CR
  • Substitute Size
  • Configure MP
  • Paper Texture ‡
  • Paper Weight ‡
  • Paper Loading ‡

PostScript Settings Quality Settings Setup Settings USB Settings

  • Print PS Error
  • Font Priority
  • Print Resolution
  • Toner Darkness
  • PQET
  • PictureGrade™
  • Printer Language
  • Power Saver
  • Resource Save
  • Download Target
  • Print Timeout
  • Wait Timeout
  • Auto Continue
  • Jam Recovery
  • Page Protect
  • Print Area
  • Display Language
  • Alarm Control
  • Toner Alarm
  • PCL SmartSwitch
  • PS SmartSwitch
  • USB Buffer

* Per supported sources † Per custom type number ‡ Per supported media

Software and network tasks

Page 104 of the Lexmark 230 user manual — 8 Supplies information
Page 104 · click to enlarge
Page 104

8 Supplies information

What supplies do I need and how do I order them? 105

How to conserve supplies 105

How to know when you need new supplies 106

How to change a toner cartridge 108

Lexmark Return Program 111

Recycling Lexmark products 111

How to change a photoconductor kit 112

Section Page · Supplies information

Page 105 of the Lexmark 230 user manual — How to conserve supplies
Page 105 · click to enlarge
Page 105

What supplies do I need and how do I order them?

There are only two supply items that have to be replaced on a regular basis: the toner cartridge and the photoconductor kit, which together comprise the print cartridge assembly. The photoconductor kit typically lasts up to 30,000 pages (at approximately 5% coverage), whereas the toner cartridge has to be replaced more frequently. How often the toner cartridge needs replacing depends on which cartridge you purchase and the average amount of toner coverage you have on your print jobs.

Within the United States or Canada, you can order Lexmark supplies from any authorized Lexmark supplies dealer. To locate the dealer nearest you, call 1-800-539-6275. In other countries, visit the Lexmark online store at www.lexmark.com or contact the place where you bought your printer.

Storing supplies

Choose a cool, clean storage area for your printer supplies. Store supplies right side up in their original packaging until you are ready to use them.

Do not expose supplies to:

  • Direct sunlight
  • Temperatures above 35°C (95°F)
  • High humidity (above 80%)
  • Salty air
  • Corrosive gases
  • Heavy dust

How to conserve supplies

Conserving supplies lowers printing costs.

  • When printing drafts, conserve toner by changing the Toner Darkness setting in your printer driver. The settings range from 1 (very light) to 10 (very dark), with 8 being the default. Setting the Toner Darkness to 1 conserves the most toner.
  • Reduce paper consumption by printing on both sides of the paper.

Supplies information

Page 106 of the Lexmark 230 user manual — Checking the toner and photoconductor levels
Page 106 · click to enlarge
Page 106

How to know when you need new supplies

The following sections describe a couple ways to determine when new supplies are needed.

Checking the toner and photoconductor levels

You can determine approximately how much toner is left in your cartridge and how full the photoconductor kit is by printing out a menu settings page. This helps you decide when you might need to order replacement supplies. For help printing a menu settings page, see “How to print the menu settings and network setup pages” on page 94.

Also, the Toner low light sequence (see page 63) is displayed when the toner cartridge is nearly empty. You can still print for a short time while this sequence is displayed, but print quality begins to decrease as the toner level decreases.

To ensure print quality and to avoid damage to the printer, the printer stops operating after the photoconductor kit has reached a maximum of 40,000 pages. (See “Replace photoconductor kit (printer hard stop)*” on page 107 for the light sequence associated with this stop.) The printer automatically notifies you before the photoconductor reaches this point. To avoid having the printer stop operating, replace the photoconductor kit when you first receive the “Replace photoconductor kit” light sequence.

While the printer may continue to function properly after the photoconductor kit has reached its official end-of-life (approximately 30,000 pages), print quality begins to significantly decrease until the photoconductor stops operating at the maximum of 40,000 pages.

Supplies information

Page 107 of the Lexmark 230 user manual — Recognizing the operator panel light sequences
Page 107 · click to enlarge
Page 107

Recognizing the operator panel light sequences

The operator panel displays certain light sequences to let you know when the toner level is low or when it’s time to replace the photoconductor kit.

Lexmark 230 — Recognizing the operator panel light sequences diagram (page 107)
Fig. 61 · Recognizing the operator panel light sequences
For more information, see page63 64 64 65

* If the operator panel lights display this sequence, the printer will not print any more jobs until the photoconductor kit is replaced.

“Toner low” and “Replace photoconductor kit” lights.

Supplies information

Page 108 of the Lexmark 230 user manual — How to change a toner cartridge
Page 108 · click to enlarge
Page 108

How to change a toner cartridge

light for an extended period of time. Extended light exposure can cause print quality problems.

1 Open the front cover by pressing the button on the left side of the printer and lowering the cover.

Supplies information

Page 109 of the Lexmark 230 user manual — How to change a toner cartridge
Page 109 · click to enlarge
Page 109

2 Remove the toner cartridge:

a Press the button on the base of the print cartridge assembly.

b Pull the toner cartridge up and out using the handle.

Lexmark 230 — How to change a toner cartridge diagram (page 109)
Fig. 62 · How to change a toner cartridge

3 Unpack the new toner cartridge.

back to Lexmark for recycling. See “Lexmark Return Program” on page 111 for more information.

4 Rotate the cartridge in all directions to distribute the toner.

Lexmark 230 — How to change a toner cartridge diagram (page 109)
Fig. 63 · How to change a toner cartridge

b · Supplies information

Page 110 of the Lexmark 230 user manual — How to change a toner cartridge
Page 110 · click to enlarge
Page 110

5 Install the new toner cartridge by aligning the white rollers on the toner cartridge with the white arrows on the tracks of the photoconductor kit and pushing the toner cartridge in as far as it will go. The cartridge clicks into place when correctly installed.

6 Close the front cover.

Supplies information

Page 111 of the Lexmark 230 user manual — Recycling Lexmark products
Page 111 · click to enlarge
Page 111

Lexmark Return Program

The Lexmark Return Program is an environmental program in which Lexmark sells new toner cartridges at a special price with the agreement that you will return them, at no cost, only to Lexmark for recycling.

Regular toner cartridges without this agreement are also available.

Lexmark Cartridge Collection Program. To learn how to return a cartridge at no cost in your country, visit Lexmark’s Web site at www.lexmark.com/recycle.

Refilled toner cartridge notice

Lexmark Return Program toner cartridges cannot be refilled. Lexmark does not recommend the use of third-party remanufactured cartridges. Lexmark cannot assure the excellent print quality and reliability of its toner cartridges after a toner cartridge has been refilled. A substantial reduction in photoconductor kit life is also likely if refilled toner cartridges are used.

printer. Printer failures caused by third-party remanufactured toner cartridges are not covered by your Lexmark printer warranty, extended warranty, or service agreement.

Recycling Lexmark products

To return your Lexmark products to Lexmark for recycling:

1 Visit our Web site:

www.lexmark.com/recycle

2 Follow the instructions on your screen.

Supplies information

Page 112 of the Lexmark 230 user manual — How to change a photoconductor kit
Page 112 · click to enlarge
Page 112

How to change a photoconductor kit

photoconductor kit exposed to direct light for an extended period of time. Extended light exposure can cause print quality problems.

1 Open the front cover by pressing the button on the left side of the printer and lowering the cover.

Supplies information

Page 113 of the Lexmark 230 user manual — How to change a photoconductor kit
Page 113 · click to enlarge
Page 113

2 Pull the print cartridge assembly out of the printer by pulling on the toner cartridge handle.

Lexmark 230 — How to change a photoconductor kit diagram (page 113)
Fig. 64 · How to change a photoconductor kit

Place the print cartridge assembly on a flat, clean surface.

3 Remove the toner cartridge:

a Press the button on the base of the print cartridge assembly.

b Pull the toner cartridge up and out using the handle.

Lexmark 230 — How to change a photoconductor kit diagram (page 113)
Fig. 65 · How to change a photoconductor kit

4 Unpack the new photoconductor kit.

a · b · Supplies information

Page 114 of the Lexmark 230 user manual — How to change a photoconductor kit
Page 114 · click to enlarge
Page 114

5 Install the toner cartridge into the new print cartridge assembly by aligning the white rollers on the toner cartridge with the white arrows on the tracks of the photoconductor kit and pushing the toner cartridge in as far as it will go. The cartridge clicks into place when correctly installed.

Lexmark 230 — How to change a photoconductor kit diagram (page 114)
Fig. 66 · How to change a photoconductor kit

6 Install the print cartridge assembly into the printer by aligning the green arrows on the guides of the print cartridge assembly with the green arrows on the tracks in the printer and pushing the print cartridge assembly in as far as it will go.

Lexmark 230 — How to change a photoconductor kit diagram (page 114)
Fig. 67 · How to change a photoconductor kit

7 Close the front cover.

instruction sheet that shipped with the new kit.

Supplies information

Page 115 of the Lexmark 230 user manual — 9 Troubleshooting
Page 115 · click to enlarge
Page 115

9 Troubleshooting

Print quality problems 118

  • How to clean the printhead lens 122

Section Page · General problems 116 · Troubleshooting

Page 116 of the Lexmark 230 user manual — General problems
Page 116 · click to enlarge
Page 116

General problems

Problem / Question Solution / Answer

What do the blinking lights mean?

See “Understanding the operator panel lights” on page 52 for information about what each light pattern means.

Why am I missing characters when I print on envelopes?

If you see voids (missing characters) when printing envelopes, check your printer driver settings to make sure you selected Envelope from the Paper Type menu.

If Envelope is already selected, try changing the texture setting to a rougher setting. Sometimes toner does not adhere well to smooth-textured envelopes. From your printer driver, select Custom 6-Rough Env from the Paper Type menu.

To change Custom 6 back to its default settings for Paper Type, Paper Texture, and Paper Weight, use the Local Printer Setup Utility on the drivers CD that shipped with your printer. If you already installed the printer drivers and utilities, skip to step 7.

1 Insert the drivers CD into your computer.

2 Click Printer Software.

3 Click Agree.

4 Select Local Printer Install, and then click Next.

5 Select your printer and port, and make sure Local Printer Setup Utility is checked.

6 Click Finish.

The Utility will be installed on your computer under Program Files (unless you chose a different directory).

7 Open the Local Printer Setup Utility.

8 From the Paper Menu, scroll through the menu items until you see the Custom menu setting.

9 Click Custom.

10 Scroll down to Custom 6 Paper Type.

11 Select envelope for the Custom 6 paper type, heavy for the Custom 6 paper weight, and rough for the Custom 6 paper texture.

12 From the toolbar, click Actions.

13 Click Apply to save the changes you made.

14 Click File Æ Exit to close the Local Printer Setup Utility.

How do I clear a paper jam?

See “How to clear paper jams” on page 26 for information about clearing jams.

The toner low light sequence is on, but I don’t have another cartridge to put in yet. Can I still print with the low cartridge?

Yes, you can still print. To extend the life of you toner cartridge somewhat, remove the cartridge, rotate it in all directions to distribute the toner, then insert it back into the printer.

When the toner low light sequence is first displayed, you should still be able to print approximately 1200 pages, based on approximately 5% coverage of pages.

The printer seems to print slower when using the manual feeder.

This is normal. The printer sometimes prints at a slightly slower speed when feeding print media from the manual feeder.

Troubleshooting

Page 117 of the Lexmark 230 user manual — General problems
Page 117 · click to enlarge
Page 117

Problem / Question Solution / Answer

I want to manually duplex card stock, but I’m having trouble getting it to feed.

The problem is that when the printer tries to manually duplex a print job, it always prints side 2 from Tray 1. However, Tray 1 does not support card stock.

To achieve the desired effect, you have to send both pages of the print job as separate jobs. After the first page has printed, reload the card stock in the manual feeder. Load the card stock in the feeder with the already-printed side down, with the top of the sheet first.

Paper stacks poorly in the output bin.

Extend the paper support on the output bin.

Dust is gathering on the paper tray when it is extended.

Attach the dust cover to the back of the printer. This protects the paper tray from the environment as well as keep the tray from being knocked out of position while it is extended.

See Attaching the dust cover for information about attaching the dust cover. The paper tray is getting bumped and pushed out the front of the printer when it is extended.

Troubleshooting

Page 118 of the Lexmark 230 user manual — ABCDE ABCDE ABCDE
Page 118 · click to enlarge
Page 118

Print quality problems

You can solve many print quality problems by replacing a supply or maintenance item that has reached the end of its intended life. Use the following table to find solutions to print quality problems.

  • White lines
  • The printhead lens is dirty.
  • Either the toner cartridge or the fuser is defective.

Try the following in this order:

1 Clean the printhead lens. (See “How to clean the printhead lens” on page 122.)

ABCDE ABCDE ABCDE

2 Replace the toner cartridge.

3 Replace the fuser*.

Streaked horizontal lines The toner cartridge or fuser may be defective, empty, or worn.

Replace the toner cartridge or fuser* as needed.

ABCDE ABCDE ABCDE

  • Streaked vertical lines
  • Toner is smeared before fusing to the paper.
  • The toner cartridge is defective.
  • If paper is stiff, try feeding from another tray or the manual feeder.
  • Replace the toner cartridge.

ABCDE ABCDE ABCDE

  • Print irregularities
  • Paper has absorbed moisture due to high humidity.
  • You are using paper that does not meet the printer specifications.
  • The fuser is worn or defective.
  • Load paper from a fresh package in the paper tray.
  • Avoid textured paper with rough finishes.
  • Make sure the printer driver paper type setting matches the type of paper you are using.

ABCDE ABCDE ABCDE

  • Replace the fuser * .

* To replace the fuser, call a service technician. † This setting can be changed using the Local Printer Setup Utility. See “Using the Local Printer Setup

Utility” on page 103 for more information.

Symptom Cause Solution · Troubleshooting

Page 119 of the Lexmark 230 user manual — ABCDE ABCDE ABCDE
Page 119 · click to enlarge
Page 119
  • Print too light
  • The Toner Darkness setting is too light.
  • You are using paper that does not meet the printer specifications.
  • The toner cartridge is low on toner.
  • The toner cartridge is defective.
  • Select a different Toner Darkness † setting from the printer driver before sending the job to print.
  • Load paper from a new package.
  • Avoid textured paper with rough finishes.
  • Make sure the paper you load in the trays is not damp.
  • Replace the toner cartridge.
  • Print too dark
  • The Toner Darkness setting is too dark.
  • The toner cartridge is defective.
  • Select a different Toner Darkness † setting from the printer driver before sending the job to print.
  • Replace the toner cartridge.

Transparency print quality is poor

  • You are using transparencies that do not meet the printer specifications.
  • The Form Type setting in the printer driver is set to something other than transparency.
  • Use only transparencies recommended by the printer’s manufacturer.
  • Make sure the Form Type setting is set to transparency.

(Print has inappropriate light or dark spots, toner is smeared, or horizontal or vertical light bands appear.)

  • Toner specks
  • The toner cartridge is defective.
  • The fuser is worn or defective.
  • Toner is in the paper path.
  • Replace the toner cartridge.
  • Replace the fuser * .
  • Call for service.

Toner rubs off the paper easily when you handle the sheets

  • The Paper Texture setting is wrong for the type of paper or specialty media you are using.
  • The Paper Weight setting is wrong for the type of paper or specialty media you are using.
  • The fuser is worn or defective.
  • Change Paper Texture † from Normal to Smooth or Rough.
  • Change Paper Weight † from Plain to CardStock (or other appropriate weight).
  • Replace the fuser * .
  • Gray background
  • The Toner Darkness setting is too dark.
  • The toner cartridge is defective.
  • Select a different Toner Darkness † setting from the printer driver before sending the job to print.
  • Replace the toner cartridge.

ABCDE ABCDE ABCDE

* To replace the fuser, call a service technician. † This setting can be changed using the Local Printer Setup Utility. See “Using the Local Printer Setup

Utility” on page 103 for more information.

Symptom Cause Solution · Troubleshooting

Page 120 of the Lexmark 230 user manual — DE DE DE
Page 120 · click to enlarge
Page 120
  • Uneven print density
  • The toner cartridge is defective.
  • Replace the toner cartridge.

A B CD E A B CD E A B CD E

  • Ghost Images
  • The Form Type setting in the printer driver is set incorrectly.
  • Toner level is low in the toner cartridge.
  • Make sure the Form Type setting is correct for the paper or specialty media you are using.
  • Replace the toner cartridge.
  • The toner cartridge is not properly installed.
  • Remove and then reinsert the toner cartridge.

DE DE DE

(Print only appears on one side of the page.)

Incorrect margins The Form Size setting in the printer driver is different than the size paper that is loaded in the tray. For example, you inserted A4 size paper into the selected tray but did not set the Form Size to A4.

Set the Form Size to A4.

  • The guides in the selected tray are not in the correct position for the paper size loaded in the tray.
  • The manual feeder’s guides are not in the correct position for the paper size loaded in the feeder.
  • Move the guides in the tray so that they are snug against the sides of the paper.
  • Move the manual feeder’s guides so that they are snug against the sides of the paper.

(Print is inappropriately slanted.)

* To replace the fuser, call a service technician. † This setting can be changed using the Local Printer Setup Utility. See “Using the Local Printer Setup

Utility” on page 103 for more information.

Show 4 more labels / short text on this page
Symptom Cause Solution · Uneven printing · Skewed print · Troubleshooting
Page 121 of the Lexmark 230 user manual — Print quality problems
Page 121 · click to enlarge
Page 121

Blank pages The toner cartridge is defective or empty.

Replace the toner cartridge.

  • Solid black pages
  • The toner cartridge is defective.
  • Your printer requires servicing.
  • Replace the toner cartridge.
  • Call for service.

Paper curls badly once it prints and exits to the bin

The Paper Texture setting is wrong for the type of paper or specialty media you are using.

Change Paper Texture† from Rough to Normal or Smooth.

* To replace the fuser, call a service technician. † This setting can be changed using the Local Printer Setup Utility. See “Using the Local Printer Setup

Utility” on page 103 for more information.

Symptom Cause Solution · Troubleshooting

Page 122 of the Lexmark 230 user manual — How to clean the printhead lens
Page 122 · click to enlarge
Page 122

How to clean the printhead lens

You can solve some print quality problems by cleaning the printhead lens.

1 Turn the printer off.

2 Open the front cover by pressing the button on the left side of the printer and lowering the cover.

Troubleshooting

Page 123 of the Lexmark 230 user manual — Print quality problems
Page 123 · click to enlarge
Page 123

3 Remove the print cartridge assembly out of the printer by pulling on the toner cartridge handle.

Place the print cartridge assembly on a flat, clean surface.

period of time. Extended light exposure can cause print quality problems.

Troubleshooting

Page 124 of the Lexmark 230 user manual — Print quality problems
Page 124 · click to enlarge
Page 124

4 Locate the glass printhead lens, which is located within the recessed area in the top of the printer.

Lexmark 230 — Print quality problems diagram (page 124)
Fig. 68 · Print quality problems

5 Gently wipe the printhead lens with a clean, dry, lint-free cloth.

6 Install the print cartridge assembly into the printer by aligning the green arrows on the guides of the print cartridge assembly with the green arrows on the tracks in the printer and pushing the print cartridge assembly in as far as it will go.

Lexmark 230 — Print quality problems diagram (page 124)
Fig. 69 · Print quality problems

7 Close the front cover.

8 Turn the printer on.

Troubleshooting

Page 126 of the Lexmark 230 user manual — Table of contents
Page 126 · click to enlarge
Page 126

Table of contents

Contentsp.2Noticesp.6Edition noticep.6Trademarksp.6Licensing noticep.7Safety informationp.7Laser noticep.7The United Kingdom Telecommunications Act 1984p.7Conventionsp.7Electronic emission noticesp.7Printer energy consumptionp.9Statement of Limited Warrantyp.9Printer overviewp.11Print media tasks and tipsp.13What types of print media can be loaded?p.14Where can print media be loaded in the printer?p.15Tips on choosing the right print mediap.16Tips on storing print media and suppliesp.18Tips on preventing jamsp.19How to load the 250-sheet and 550-sheet traysp.20How to load the manual feederp.24How to use the rear exitp.25How to clear paper jamsp.26Printing tasksp.29How to manually feed a print jobp.30How to print on both sides of the paper (manual duplex)p.32How to print multiple page images on one page (N-upprinting)p.34How to print a bookletp.35How to print a posterp.36How to print on letterheadp.37How to print using an overlay or a watermarkp.37How to cancel a print jobp.39How to install optionsp.40How to access the system boardp.41How to add a memory cardp.45How to add a flash cardp.46How to install a 550-sheet drawerp.48How to get the printer driver to recognize installed optionsp.49Using the operator panelp.50Overview of the operator panelp.51Understanding the operator panel lightsp.52Operator panel codesp.57Understanding the printer configuration menusp.83Printing the Printer Settings Configuration sheetp.83Configuration menus overviewp.84Software and network tasksp.88How to install drivers for local printingp.89How to print the menu settings and network setup pagesp.94How to print a test pagep.94How to configure for TCP/IPp.95How to set up the printer for network printingp.96Using the printer resident Web pagep.102Using the Local Printer Setup Utilityp.103Supplies informationp.104What supplies do I need and how do I order them?p.105How to conserve suppliesp.105How to know when you need new suppliesp.106How to change a toner cartridgep.108Lexmark Return Programp.111Recycling Lexmark productsp.111How to change a photoconductor kitp.112Troubleshootingp.115General problemsp.116Print quality problemsp.118Indexp.125
Page 127 of the Lexmark 230 user manual — Table of contents
Page 127 · click to enlarge
Page 127

Table of contents

Contentsp.2Noticesp.6Edition noticep.6Trademarksp.6Licensing noticep.7Safety informationp.7Laser noticep.7The United Kingdom Telecommunications Act 1984p.7Conventionsp.7Electronic emission noticesp.7Printer energy consumptionp.9Statement of Limited Warrantyp.9Printer overviewp.11Print media tasks and tipsp.13What types of print media can be loaded?p.14Where can print media be loaded in the printer?p.15Tips on choosing the right print mediap.16Tips on storing print media and suppliesp.18Tips on preventing jamsp.19How to load the 250-sheet and 550-sheet traysp.20How to load the manual feederp.24How to use the rear exitp.25How to clear paper jamsp.26Printing tasksp.29How to manually feed a print jobp.30How to print on both sides of the paper (manual duplex)p.32How to print multiple page images on one page (N-upprinting)p.34How to print a bookletp.35How to print a posterp.36How to print on letterheadp.37How to print using an overlay or a watermarkp.37How to cancel a print jobp.39How to install optionsp.40How to access the system boardp.41How to add a memory cardp.45How to add a flash cardp.46How to install a 550-sheet drawerp.48How to get the printer driver to recognize installed optionsp.49Using the operator panelp.50Overview of the operator panelp.51Understanding the operator panel lightsp.52Operator panel codesp.57Understanding the printer configuration menusp.83Printing the Printer Settings Configuration sheetp.83Configuration menus overviewp.84Software and network tasksp.88How to install drivers for local printingp.89How to print the menu settings and network setup pagesp.94How to print a test pagep.94How to configure for TCP/IPp.95How to set up the printer for network printingp.96Using the printer resident Web pagep.102Using the Local Printer Setup Utilityp.103Supplies informationp.104What supplies do I need and how do I order them?p.105How to conserve suppliesp.105How to know when you need new suppliesp.106How to change a toner cartridgep.108Lexmark Return Programp.111Recycling Lexmark productsp.111How to change a photoconductor kitp.112Troubleshootingp.115General problemsp.116Print quality problemsp.118Indexp.125
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
What do the blinking lights mean?See “Understanding the operator panel lights” on page 52 for information about what each light pattern means. p.116
Why am I missing characters when I print on envelopes?If you see voids (missing characters) when printing envelopes, check your printer driver settings to make sure you selected Envelope from the Paper Type menu. If Envelope is already selected, try changing the texture setting to a rougher setting. Sometimes toner does not adhere well to smooth-textured envelopes. From your printer driver, select Custom 6-Rough Env from the Paper Type menu. To change Custom 6 back to its default settings for Paper Type, Paper Texture, and Paper Weight, use the Local Printer Setup Utility on the drivers CD that shipped with your printer. If you already installed the printer drivers and utilities, skip to step 7. 1 Insert the drivers CD into your computer. 2 Click Printer Software. 3 Click Agree. 4 Select Local Printer Install, and then click Next. 5 Select your printer and port, and make sure Local Printer Setup Utility is checked. 6 Click Finish. The Utility will be installed on your computer under Program Files (unless you chose a different directory). 7 Open the Local Printer Setup Utility. 8 From the Paper Menu, scroll through the menu items until you see the Custom menu setting. 9 Click Custom. 10 Scroll down to Custom 6 Paper Type. 11 Select envelope for the Custom 6 paper type, heavy for the Custom 6 paper weight, and rough for the Custom 6 paper texture. 12 From the toolbar, click Actions. 13 Click Apply to save the changes you made. 14 Click File Æ Exit to close the Local Printer Setup Utility. p.116
How do I clear a paper jam?See “How to clear paper jams” on page 26 for information about clearing jams. p.116
The toner low light sequence is on, but I don’t have another cartridge to put in yet. Can I still print with the low cartridge?Yes, you can still print. To extend the life of you toner cartridge somewhat, remove the cartridge, rotate it in all directions to distribute the toner, then insert it back into the printer. When the toner low light sequence is first displayed, you should still be able to print approximately 1200 pages, based on approximately 5% coverage of pages. p.116
The printer seems to print slower when using the manual feeder.This is normal. The printer sometimes prints at a slightly slower speed when feeding print media from the manual feeder. p.116
I want to manually duplex card stock, but I’m having trouble getting it to feed.The problem is that when the printer tries to manually duplex a print job, it always prints side 2 from Tray 1. However, Tray 1 does not support card stock. To achieve the desired effect, you have to send both pages of the print job as separate jobs. After the first page has printed, reload the card stock in the manual feeder. Load the card stock in the feeder with the already-printed side down, with the top of the sheet first. p.117
Paper stacks poorly in the output bin.Extend the paper support on the output bin. p.117
Dust is gathering on the paper tray when it is extended.Attach the dust cover to the back of the printer. This protects the paper tray from the environment as well as keep the tray from being knocked out of position while it is extended. See Attaching the dust cover for information about attaching the dust cover. p.117
The paper tray is getting bumped and pushed out the front of the printer when it is extended. p.117
White lines ABCDE ABCDE ABCDE• The printhead lens is dirty. • Either the toner cartridge or the fuser is defective.Try the following in this order: 1 Clean the printhead lens. (See “How to clean the printhead lens” on page 122.) 2 Replace the toner cartridge. 3 Replace the fuser*. p.118
Streaked horizontal lines ABCDE ABCDE ABCDEThe toner cartridge or fuser may be defective, empty, or worn.Replace the toner cartridge or fuser* as needed. p.118
Streaked vertical lines ABCDE ABCDE ABCDE• Toner is smeared before fusing to the paper. • The toner cartridge is defective.• If paper is stiff, try feeding from another tray or the manual feeder. • Replace the toner cartridge. p.118
Print irregularities ABCDE ABCDE ABCDE• Paper has absorbed moisture due to high humidity. • You are using paper that does not meet the printer specifications. • The fuser is worn or defective.• Load paper from a fresh package in the paper tray. • Avoid textured paper with rough finishes. • Make sure the printer driver paper type setting matches the type of paper you are using. • Replace the fuser*. p.118
* To replace the fuser, call a service technician. † This setting can be changed using the Local Printer Setup Utility. See “Using the Local Printer Setup Utility” on page 103 for more information. p.118
Print too light• The Toner Darkness setting is too light. • You are using paper that does not meet the printer specifications. • The toner cartridge is low on toner. • The toner cartridge is defective.• Select a different Toner Darkness† setting from the printer driver before sending the job to print. • Load paper from a new package. • Avoid textured paper with rough finishes. • Make sure the paper you load in the trays is not damp. • Replace the toner cartridge. p.119
Print too dark• The Toner Darkness setting is too dark. • The toner cartridge is defective.• Select a different Toner Darkness† setting from the printer driver before sending the job to print. • Replace the toner cartridge. p.119
Transparency print quality is poor (Print has inappropriate light or dark spots, toner is smeared, or horizontal or vertical light bands appear.)• You are using transparencies that do not meet the printer specifications. • The Form Type setting in the printer driver is set to something other than transparency.• Use only transparencies recommended by the printer’s manufacturer. • Make sure the Form Type setting is set to transparency. p.119
Toner specks• The toner cartridge is defective. • The fuser is worn or defective. • Toner is in the paper path.• Replace the toner cartridge. • Replace the fuser*. • Call for service. p.119
Toner rubs off the paper easily when you handle the sheets• The Paper Texture setting is wrong for the type of paper or specialty media you are using. • The Paper Weight setting is wrong for the type of paper or specialty media you are using. • The fuser is worn or defective.• Change Paper Texture† from Normal to Smooth or Rough. • Change Paper Weight† from Plain to CardStock (or other appropriate weight). • Replace the fuser*. p.119
Gray background ABCDE ABCDE ABCDE• The Toner Darkness setting is too dark. • The toner cartridge is defective.• Select a different Toner Darkness† setting from the printer driver before sending the job to print. • Replace the toner cartridge. p.119
Uneven print density ABCDE ABCDE ABCDE• The toner cartridge is defective.• Replace the toner cartridge. p.120
Ghost Images• The Form Type setting in the printer driver is set incorrectly. • Toner level is low in the toner cartridge.• Make sure the Form Type setting is correct for the paper or specialty media you are using. • Replace the toner cartridge. p.120
Uneven printing DE DE DE (Print only appears on one side of the page.)• The toner cartridge is not properly installed.• Remove and then reinsert the toner cartridge. p.120
Incorrect marginsThe Form Size setting in the printer driver is different than the size paper that is loaded in the tray. For example, you inserted A4 size paper into the selected tray but did not set the Form Size to A4.Set the Form Size to A4. p.120
Skewed print (Print is inappropriately slanted.)• The guides in the selected tray are not in the correct position for the paper size loaded in the tray. • The manual feeder’s guides are not in the correct position for the paper size loaded in the feeder.• Move the guides in the tray so that they are snug against the sides of the paper. • Move the manual feeder’s guides so that they are snug against the sides of the paper. p.120
Blank pagesThe toner cartridge is defective or empty.Replace the toner cartridge. p.121
Solid black pages• The toner cartridge is defective. • Your printer requires servicing.• Replace the toner cartridge. • Call for service. p.121
Paper curls badly once it prints and exits to the binThe Paper Texture setting is wrong for the type of paper or specialty media you are using.Change Paper Texture† from Rough to Normal or Smooth. p.121

Ask about the Lexmark 230

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lexmark 230

Be the first to ask — other owners or our team will answer.

Original document

Lexmark 230 manual PDF

127 pages·7.8 MB·Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…