
User's Guide
Machine type(s):
Model(s):
220, 230


Connect the power cord to a properly grounded electrical outlet that is near the product and easily accessible.
Do not place or use this product near water or wet locations.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
Use only the power cord provided with this product or the manufacturer's authorized replacement.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a service representative.
Safety information 5

SAVE THESE INSTRUCTIONS.
Safety information 6

Learning about the printer 7
Finding information about the printer

Learning about the printer 8
When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any hardware options, then leave enough room for them also. It is important to:

Learning about the printer 9

You can configure your printer by adding one optional 250‑ or 550‑sheet tray. For instructions on installing the optional tray, see “Installing optional trays” on page 17.

Learning about the printer 10


1 Printer control panel
9 Front door

Learning about the printer 11
1 2 3 4 5 6



Learning about the printer 12

The printer control panel lights can mean different things, depending on the light sequence. The lights can be on, off, blinking, or blinking slowly, indicating a printer status, a warning, or an error. Some errors have the same light sequence. The following table shows the appearances of the lights.

If the printer control panel light sequence matches a light sequence in the following table, then see the message in the same row.


Learning about the printer 13

The printer control panel lights blink one at a time from left to right repeatedly.
If the printer control panel light sequence matches a light sequence in the “Primary light sequence” column of the
following table, then press twice quickly on the printer control panel. Search for a matching light sequence in the “Supplemental light sequence” column, and then see the message in the same row.

Learning about the printer 14


Learning about the printer 15

Use the Embedded Web Server to:
To access the Embedded Web Server for your printer:
1 Obtain the printer IP address by printing a network setup page or menu settings page, and then finding the TCP/IP section.
For more information, see “Printing a menu settings and network setup page” on page 28.
2 Open a Web browser, and then type the printer IP address in the address field.
3 Press Enter.
The Local Printer Settings Utility lets you change and save settings for a printer that is connected to a computer locally through a USB or parallel cable.

Learning about the printer 16
To download and install the Local Printer Settings Utility, see “Installing the Local Printer Settings Utility” on page 20.
To access the Local Printer Settings Utility:
From the Search charm, type local printer settings utility, and then navigate to:
Apps list > Local Printer Settings Utility
or Start.
2 Click All Programs or Programs > Lexmark > Local Printer Settings Utility.
To save your settings, click Actions > Apply Settings.
You can also distribute your settings to other printers by saving the settings in a command file. To save your settings in a command file, click Actions > Save As Command File.
1 Click

Additional printer setup 17
Installing hardware options
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer using the power switch, and then unplug the power cord from the electrical outlet.


2 Unpack the tray, and then remove any packing material.
3 Remove the tray from the base.

4 Remove any packing material from inside the tray.
5 Insert the tray into the base.
6 Place the tray near the printer.

Additional printer setup 18
7 Align the printer with the tray, and then slowly lower the printer into place.

8 Connect the power cord to the printer, then to a properly grounded electrical outlet, and then turn on the printer.
Connect the printer to the computer using a USB or parallel cable, or to the network using an Ethernet cable.
Make sure to match the following:

Additional printer setup 19

1 USB port* Attach an optional wireless network adapter.
2 USB printer port Connect the printer to a computer.
3 Ethernet port* Connect the printer to a network.
4 Parallel port* Connect the printer to a computer.
5 Power switch Turn on or turn off the printer.
6 Printer power cord socket Connect the printer to an electrical outlet.
7 Security slot Attach a lock that will secure the printer in place.
* These ports are available only in select printer models.
Use the To

Additional printer setup 20
2 Do either of the following: • If you are using the Software and Documentation CD, then insert the CD and wait for the installation dialog to appear. If the installation dialog does not appear, then do the following:
From the Search charm, type run, and then navigate to: Apps list > Run > type D:\setup.exe > OK.
, or click Start and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
c Press Enter, or click OK.
Click the CD icon on the desktop. • If you are using the downloaded software installer from the Web, then double‑click the installer that you have saved in your computer. Wait for the Select Installation Type dialog to appear, and then click Install.
3 Click Install, and then follow the instructions on the computer screen.
1 Visit http://support.lexmark.com, and then download the software.
2 Double‑click the software installer package.
3 Select an installation type, and then click Install.
4 Click Install to start the installation.
5 Click Agree to accept the license agreement.
6 Click Continue, and then follow the instructions on the computer screen.
a Click

Additional printer setup 21
When any hardware options are installed, you may need to manually add the options in the printer driver to make them available for use.
1 Open the printers folder.
From the Search charm, type run, and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
4 Click the Configuration tab.
6 Click Apply.
2 Add any installed hardware options, and then click OK.
In Windows 8 · a Click

Additional printer setup 22
To configure your printer to connect to an Ethernet network, organize the following information before you begin:
You will need an Ethernet cable to connect the printer to the network and an available port where the printer can physically connect to the network. Use a new network cable when possible to avoid potential problems caused by a damaged cable.
2 Do either of the following: • If you are using the Software and Documentation CD, then insert the CD and wait for the installation dialog to appear. If the installation dialog does not appear, then do the following:
From the Search charm, type run, and then navigate to: Apps list > Run > type D:\setup.exe > OK
In Windows 8

Additional printer setup 23
In Windows 7 or earlier
, or click Start and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
c Press Enter, or click OK.
3 Click Install, and then follow the instructions on the computer screen.
4 Select Ethernet connection, and then click Continue.
5 Attach the Ethernet cable when instructed to do so.
6 Select the printer from the list, and then click Continue.
7 Follow the instructions on the computer screen.
1 Allow the network DHCP server to assign an IP address to the printer.
3 Install the printer driver on the computer. a Insert the Software and Documentation CD, and then double‑click the installer package for the printer. b Follow the instructions on the computer screen.
c Select a destination, and then click Continue. d From the Easy Install screen, click Install. e Type the user password, and then click OK.
All the necessary applications are installed on the computer. f Click Close when installation is complete.
4 Add the printer. • For IP printing: a From the Apple menu, navigate to either of the following:
– System Preferences > Print & Scan – System Preferences > Print & Fax b Click +.
c If necessary, click Add Printer or Scanner or Add Other Printer or Scanner.
a Click

Additional printer setup 24
d Click the IP tab. e Type the printer IP address in the address field, and then click Add. • For AppleTalk printing:
– Make sure AppleTalk is activated on your printer. – This feature is supported only in Mac OS X version 10.5. a From the Apple menu, navigate to:
System Preferences > Print & Fax b Click +, and then navigate to:
AppleTalk > select your printer > Add
Make sure you have the following information before setting up the printer on a wireless network:
Some ad hoc networks will also require the automatic setting. Check with your system support person if you are not sure which channel to select. • Security Method—There are three basic options for Security Method: – WEP key
If your network uses more than one WEP key, then enter up to four in the provided spaces. Select the key currently in use on the network by selecting the default WEP transmit key. or – WPA or WPA2 preshared key or passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network. – 802.1X–RADIUS
If you are installing the printer on an 802.1X network, then you may need the following:
If your wireless network does not use any type of security, then you will not have any security information.

Additional printer setup 25
– If you do not know the SSID of the network that your computer is connected to, then launch the wireless utility
of the computer network adapter, and then look for the network name. If you cannot find the SSID or the security information for your network, then see the documentation that came with the access point, or contact your system support person. – To find the WPA/WPA2 preshared key/passphrase for the wireless network, see the documentation that came
with the access point, see the Web page associated with the access point, or consult your system support person.
Connecting the printer to a wireless network using the Wi‑Fi Protected Setup PIN
The printer supports only the personal identification number (PIN) method of connecting to a wireless network using Wi‑Fi Protected Setup (WPS) methods.
1 Print a network setup page or menu settings page. For more information, see “Printing a menu settings and network setup page” on page 28.
2 Locate the WPS PIN in the Wireless section.
3 Open a Web browser, and then type the IP address of your access point in the address field.
4 Access the WPS settings. For more information, see the documentation that came with your access point.
5 Enter the eight‑digit WPS PIN, and then save the setting.
The Wireless Setup Utility lets you:

Additional printer setup 26
Installing the Wireless Setup Utility
2 Double‑click the software installer package.
Wait for the installation dialog to appear.
If you are using a Software and Documentation CD and the installation dialog does not appear, then do the following:
From the Search charm, type run, and then navigate to:
Apps list > Run > type D:\setup.exe > OK.
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
c Press Enter or click OK.
3 Follow the instructions on the computer screen.
Launching the Wireless Setup Utility
1 Run the utility.
From the Search charm, type printer home, and then navigate to:
Apps list > Printer Home > Settings > Wireless Setup Utility
In Windows 7 or earlier
or Start. b Click All Programs or Programs, and then select the printer program folder from the list.
c Select your printer, and then navigate to: Printer Home > Settings > Wireless Setup Utility
2 Follow the instructions on the computer screen.

Additional printer setup 27
The Wireless Setup Assistant lets you:
Installing the Wireless Setup Assistant
1 Go to the Lexmark Web site at http://support.lexmark.com.
2 Download the latest Wireless Setup Assistant application.
3 Double‑click the downloaded software installer package.
4 Follow the instructions on the computer screen.
Launching the Wireless Setup Assistant
1 From the Finder, navigate to:
Applications > select your printer folder
2 Double‑click Wireless Setup Assistant, and then follow the instructions on the computer screen.
?.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Network/Ports > Wireless.
3 Modify the settings to match the settings of your access point (wireless router).
4 Click Submit.

Additional printer setup 28
5 Turn off the printer, and then disconnect the Ethernet cable. Then wait for at least five seconds, and then turn the printer back on.
6 To verify if your printer is connected to the network, print a network setup page again. Then in the Network Card [x] section, see if the status is “Connected”.
Print a menu settings page to review the current menu settings and to verify if the printer options are installed correctly. The network setup page prints at the same time, containing the current network settings of the printer and levels of supplies.
From the printer control panel, press for at least four seconds.

Loading paper and specialty media 29
The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 92 and “Storing paper” on page 46.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu.
Depending on your operating system, access the Paper menu using the Local Printer Settings Utility or Printer Settings.
The Universal paper size setting is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Universal Setup.
3 Select the unit of measure, or click Portrait Width or Portrait Height.
4 Change the setting, and then click Submit.
1 Depending on your operating system, access the Paper menu using the Local Printer Settings Utility or Printer Settings.
2 Select the tray containing the Universal paper size, and then select Universal as the paper size.

Loading paper and specialty media 30
The standard bin holds up to 150 sheets of 75‑g/m2 (20‑lb) paper. It collects prints facedown. The standard bin includes a paper stop that keeps paper from sliding out the front of the bin as it stacks.
To open the paper stop, pull it so that it flips forward.

1 Pull out the tray completely.

Loading paper and specialty media 31


Busy · ‑ Blinking

Loading paper and specialty media 32
2 Squeeze and then slide the width guide tab to the correct position for the size of the paper you are loading.


LGL
B5
EXEC
A5
3 Squeeze and then slide the length guide tab to the correct position for the size of the paper you are loading.


LGL
B5
EXEC
A5

Loading paper and specialty media 33



LTR/LGL EXEC
A5
4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper stack.

Loading paper and specialty media 34


6 Insert the tray.

7 From the Embedded Web Server or your computer, set the paper size and type in the Paper menu to match the paper loaded in the tray.

Loading paper and specialty media 35
Use the multipurpose feeder when printing on different paper sizes and types or specialty media, such as card stock, transparencies, paper labels, and envelopes. You can also use it for single‑page print jobs on letterhead.
1 Open the multipurpose feeder.


a Pull the multipurpose feeder extender.

b Pull the extender gently so that the multipurpose feeder is fully extended and open.


Loading paper and specialty media 36
2 Squeeze the tab on the left width guide, and then move the guides for the paper you are loading.


3 Prepare the paper or specialty media for loading. • Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

4 Load the paper or specialty media.

Loading paper and specialty media 37






Loading paper and specialty media 38
5 From the Embedded Web Server or from your computer, set the paper size and paper type in the Paper menu to match the paper loaded in the multipurpose feeder.
When the paper size and paper type for any trays are the same, the printer will link those trays. When one linked tray becomes empty, paper will feed from the next linked tray. It is recommended to give all unique paper, such as letterhead and different colored plain papers, a different custom type name so that the trays they are in will not automatically link.
1 Open a Web browser, and then type the printer IP address in the address field.

Loading paper and specialty media 39
2 Click Settings > Paper Menu.
4 Click Submit.
Depending on your operating system, access the Paper menu using the Local Printer Settings Utility or Printer Settings.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Types.
3 Select a custom paper type name, and then select a custom paper type.
4 Click Submit.
Depending on your operating system, access the Custom menu using the Local Printer Settings Utility or Printer Settings.
1 Open a Web browser, and then type the printer IP address in the address field.

Loading paper and specialty media 40
2 Click Settings > Paper Menu.
3 From the Tray Configuration section, select a paper source, and then select a custom paper type under the paper type column.
4 Click Submit.
Depending on your operating system, access the Paper menu using the Local Printer Settings Utility or Printer Settings.

Paper and specialty media guide 41
Additional information for printing on specialty media may be found in the Cardstock and Label Guide available at http://support.lexmark.com.
Selecting the correct paper or specialty media reduces printing problems. For the best print quality, try a sample of the paper or specialty media before buying large quantities.
The following paper characteristics affect print quality and reliability. Consider these characteristics when evaluating new paper stock.
The printer trays can automatically feed paper weights up to 120‑g/m2 (32‑lb) bond grain long paper. The multipurpose feeder can automatically feed paper weights up to 163‑g/m2 (43‑lb) bond grain long paper. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 75‑g/m2 (20‑lb) bond grain long paper. For paper smaller than 182 x 257 mm (7.2 x 10.1 inches), we recommended to use 90 g/m2
(24 lb) or heavier paper.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.
Paper smoothness directly affects print quality. If paper is too rough, then toner cannot fuse to it properly. If paper is too smooth, then it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; however, smoothness between 150 and 250 Sheffield points produces the best print quality.
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.
Store paper in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extend the time to several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.

Paper and specialty media guide 42
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60–90‑g/m2 (16–24‑lb) bond paper, grain long paper is recommended.
Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton can negatively affect paper handling.
The following paper types are not recommended for use with the printer:
Using the appropriate paper prevents jams and helps ensure trouble‑free printing.
To help avoid paper jams and poor print quality:
Use these guidelines when selecting preprinted forms and letterhead:

Paper and specialty media guide 43
Use papers printed with heat‑resistant inks designed for use in xerographic copiers. The ink must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions. Use inks that are not affected by the resin in toner. Inks that are oxidation‑set or oil‑based generally meet these requirements; latex inks might not. When in doubt, contact the paper supplier.
Preprinted papers such as letterhead must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions.
As an environmentally conscientious company, Lexmark supports the use of recycled paper produced specifically for use in laser (electrophotographic) printers.
While no blanket statement can be made that all recycled paper will feed well, Lexmark consistently tests papers that represent recycled cut size copier papers available on the global market. This scientific testing is conducted with rigor and discipline. Many factors are taken into consideration both separately and as a whole, including the following:
Recycled papers are better than ever; however, the amount of recycled content in a paper affects the degree of control over foreign matter. And while recycled papers are one good path to printing in an environmentally responsible manner, they are not perfect. The energy required to de-ink and deal with additives such as colorants and “glue” often generates more carbon emissions than does normal paper production. However, using recycled papers enables better resource management overall.
Lexmark concerns itself with the responsible use of paper in general based on life cycle assessments of its products. To gain a better understanding of the impact of printers on the environment, the company commissioned a number of life cycle assessments and found that paper was identified as the primary contributor (up to 80%) of carbon emissions caused throughout the entire life of a device (from design to end-of-life). This is due to the energy-intensive manufacturing processes required to make paper.
Thus, Lexmark seeks to educate customers and partners on minimizing the impact of paper. Using recycled paper is one way. Eliminating excessive and unnecessary paper consumption is another. Lexmark is well-equipped to help customers minimize printing and copying waste. In addition, the company encourages purchasing paper from suppliers who demonstrate their commitment to sustainable forestry practices.

Paper and specialty media guide 44
Lexmark does not endorse specific suppliers, although a converter’s product list for special applications is maintained. However, the following paper choice guidelines will help alleviate the environmental impact of printing:
1 Minimize paper consumption.
2 Be selective about the origin of wood fiber. Buy from suppliers who carry certifications such as the Forestry Stewardship Council (FSC) or the Program for the Endorsement of Forest Certification (PEFC). These certifications guarantee that the paper manufacturer uses wood pulp from forestry operators that employ environmentally and socially responsible forest management and restoration practices.
3 Choose the most appropriate paper for printing needs: normal 75 or 80 g/m2 certified paper, lower weight paper, or recycled paper.
Test results indicate that the following paper types are at risk for use with laser printers:
For more information about Lexmark, visit www.lexmark.com. General sustainability-related information can be found at the Environmental Sustainability link.
Card stock is heavy, single‑ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly impact print quality. Print samples on the card stock being considered for use before buying large quantities.
When printing on card stock:

Paper and specialty media guide 45
Print samples on the envelopes being considered for use before buying large quantities.
Print samples on the labels being considered for use before buying large quantities.
For more information on label printing, characteristics, and design, see the Card Stock & Label Guide available at http://support.lexmark.com.
When printing on labels:
releasing hazardous emissions. – Label adhesives, face sheet (printable stock), and topcoats can withstand up to 172‑kPa (25‑psi) pressure without

Paper and specialty media guide 46
Use these paper storage guidelines to help avoid jams and uneven print quality:

Paper and specialty media guide 47
Paper size Standard tray Optional 250‑ or 550‑sheet tray Multipurpose feeder Duplex mode
210 x 297 mm (8.3 x 11.7 in.)
148 x 210 mm (5.8 x 8.3 in.)
105 x 148 mm (4.1 x 5.8 in.)
JIS B5 182 x 257 mm (7.2 x 10.1 in.) X
216 x 279 mm (8.5 x 11 in.)
216 x 356 mm (8.5 x 14 in.)
184 x 267 mm (7.3 x 10.5 in.)
Oficio (Mexico) 216 x 340 mm (8.5 x 13.4 in.)
216 x 330 mm (8.5 x 13 in.)
140 x 216 mm (5.5 x 8.5 in.)
76.2 x 127 mm (3 x 5 in.) up to 216 x 356 mm (8.5 x 14 in.)
7 3/4 Envelope (Monarch)
98 x 191 mm (3.9 x 7.5 in.)
98 x 225 mm (3.9 x 8.9 in.)
105 x 241 mm (4.1 x 9.5 in.)
1 This size setting formats the page for 216 x 356 mm (8.5 x 14 in.) unless the size is specified by the software application.
2 Universal is supported in the standard tray only if the paper size is at least 105 x 148 mm (4.1 x 5.8 in.). Universal is supported in the optional 250- or 550-sheet tray only if the paper size is at least 148 x 210 mm (5.8 x 8.3 in.). Universal is supported in duplex mode only if the width is at least 210 mm (8.3 in.) and the length is at least 279 mm (11 in.). The smallest supported Universal size is supported only in the multipurpose feeder.

Paper and specialty media guide 48
Paper size Standard tray Optional 250‑ or 550‑sheet tray Multipurpose feeder Duplex mode
110 x 220 mm (4.3 x 8.7 in.)
162 x 229 mm (6.4 x 9 in.)
B5 Envelope 176 x 250 mm (6.9 x 9.8 in.) X X X
229 x 356 mm (9 x 14 in.)
1 This size setting formats the page for 216 x 356 mm (8.5 x 14 in.) unless the size is specified by the software application.
2 Universal is supported in the standard tray only if the paper size is at least 105 x 148 mm (4.1 x 5.8 in.). Universal is supported in the optional 250- or 550-sheet tray only if the paper size is at least 148 x 210 mm (5.8 x 8.3 in.). Universal is supported in duplex mode only if the width is at least 210 mm (8.3 in.) and the length is at least 279 mm (11 in.). The smallest supported Universal size is supported only in the multipurpose feeder.
The standard tray supports 60–90‑g/m2 (16–24‑lb) paper weights. The optional tray supports 60–120‑g/m2 (16–32‑lb) paper weights. The multipurpose feeder supports 60–163‑g/m2 (16–43‑lb) paper weights.

Paper type 250‑ or 550‑sheet tray Multipurpose feeder Duplex mode
DL Envelope · C5 Envelope · Other Envelope

Paper and specialty media guide 49
Paper type 250‑ or 550‑sheet tray Multipurpose feeder Duplex mode
1 One‑sided paper labels designed for laser printers are supported for occasional use. It is recommended to print 20 or fewer pages of paper labels per month. Vinyl, pharmacy, and two‑sided labels are not supported.
2 Bond and Heavy Paper are supported in duplex mode up to 90‑g/m2 (24‑lb) paper weight.
Light Paper · Heavy Paper2 · Rough/Cotton X

This chapter covers printing, printer reports, and job cancelation. Selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 92 and “Storing paper” on page 46.
1 From the Embedded Web Server or your computer, set the paper size and type in the Paper menu to match the paper loaded in the tray.
2 Send the print job.
a With a document open, click File > Print. b Click Properties, Preferences, Options, or Setup.
c Adjust the settings, if necessary. d Click OK > Print.
a Customize the settings in the Page Setup dialog.
1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the paper loaded. 3 Click OK. b Customize the settings in the Print dialog.
1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options. 2 From the Print dialog and pop‑up menus, adjust the settings if necessary.
1 Open a Web browser, and then type the printer IP address in the address field.
Printing 50

2 Click Settings > Print Settings > Quality Menu.
3 Adjust the toner darkness setting.
4 Click Submit.
Depending on your operating system, adjust the toner darkness settings using the Local Printer Settings Utility or Printer Settings.
To download a compatible mobile printing application, visit www.lexmark.com/mobile.
1 Open the printers folder.
From the Search charm, type run, and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
2 Double‑click the printer icon.
3 Select the print job you want to cancel.
4 Click Delete.
Printing 51 · In Windows 8 · a Click

2 From the printer window, select the print job you want to cancel, and then delete it.
Printing 52

Understanding the printer menus 53
You may print a menus list by printing the menu settings and network setup pages. Access the menus from a network printer by using the Embedded Web Server. If your printer is connected by USB or parallel cable, then access the menus using the Local Printer Settings Utility for Windows or Printer Settings for Macintosh.
Paper Texture Paper Weight
Standard USB Set Date and Time
Set a default paper source for all print jobs.
Tray [x] MP Feeder Manual Paper Manual Envelope

Understanding the printer menus 54
Specify the paper size loaded in each tray.
A4 A5 A6 JIS‑B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the type of paper loaded in each tray.
Plain Paper Transparency Recycled Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Use To · Tray [x] Size · Tray [x] Type

Understanding the printer menus 55
Specify the paper size loaded in the multipurpose feeder.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the type of paper loaded in the multipurpose feeder.
Plain Paper Card Stock Transparency Recycled Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Use To · MP Feeder Size · MP Feeder Type

Understanding the printer menus 56
Specify the paper size being manually loaded.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the paper type being manually loaded.
Plain Paper Card Stock Transparency Recycled Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Specify the envelope size being manually loaded.
7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the envelope type being manually loaded.
Envelope Rough Envelope Custom Type [x]

Understanding the printer menus 57
Determine when the printer selects paper from the multipurpose feeder.
Specify the relative texture of the plain paper loaded.
Specify the relative texture of the card stock loaded.
Specify the relative texture of the transparencies loaded.
Specify the relative texture of the recycled paper loaded.
Specify the relative texture of the labels loaded.
Specify the relative texture of the bond paper loaded.
Specify the relative texture of the envelopes loaded.

Understanding the printer menus 58
Specify the relative texture of the rough envelopes loaded.
Specify the relative texture of the letterhead loaded.
Specify the relative texture of the preprinted paper loaded.
Specify the relative texture of the colored paper loaded.
Specify the relative texture of the paper loaded.
Specify the relative texture of the paper loaded.
Specify the relative texture of the cotton paper loaded.
Specify the relative texture of the custom paper loaded.
Specify the relative weight of the plain paper loaded.
Specify the relative weight of the card stock loaded.

Understanding the printer menus 59
Specify the relative weight of the transparencies loaded.
Specify the relative weight of the recycled paper loaded.
Specify the relative weight of the labels loaded.
Specify the relative weight of the bond paper loaded.
Specify the relative weight of the envelope loaded.
Specify the relative weight of the rough envelope loaded.
Specify the relative weight of the letterhead loaded.
Specify the relative weight of the preprinted paper loaded.
Specify the relative weight of the colored paper loaded.
Specify that the weight of the paper loaded is light.
Specify that the weight of the paper loaded is heavy.

Understanding the printer menus 60
Specify the relative weight of the cotton or rough paper loaded.
Specify the relative weight of the custom paper loaded.
Determine and set two‑sided printing for all print jobs that specify Recycled as the paper type.
Determine and set two‑sided printing for all print jobs that specify Bond as the paper type.
Determine and set two‑sided printing for all print jobs that specify Letterhead as the paper type.
Determine and set two‑sided printing for all print jobs that specify Preprinted as the paper type.
Determine and set two‑sided printing for all print jobs that specify Colored as the paper type.
Determine and set two‑sided printing for all print jobs that specify Light as the paper type.
Determine and set two‑sided printing for all print jobs that specify Heavy as the paper type.

Understanding the printer menus 61
Determine and set two‑sided printing for all print jobs that specify Custom [x] as the paper type.
Associate a paper or specialty media type with a Custom Type [x] name.
Paper Card Stock Transparency Rough/Cotton Labels Envelope
Specify a paper type when the Recycled setting is selected in other menus.
Paper Card Stock Transparency Rough/Cotton Labels Envelope Cotton
Set the printer to automatically switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language.

Understanding the printer menus 62
Set the printer to automatically switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the size of the USB input buffer.
Disabled Auto 3K to [maximum size allowed]

Understanding the printer menus 63
Set the language of the text appearing on the Embedded Web Server, Local Printer Settings for Windows, or Printer Settings for Macintosh.
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portuguese Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese
Minimize the use of energy, paper, or specialty media.
Off Energy Energy/Paper Paper
Use To · Display Language · Eco-Mode

Understanding the printer menus 64
Set the amount of time the printer waits after a job is printed before it goes into a reduced power state.
To wake the printer from Sleep mode, try one of the following:
Set the amount of time the printer waits after a job is printed before it enters Hibernate mode.
Disabled 1 hour 2 hours 3 hours 6 hours 1 day 2 days 3 days 1 week 2 weeks 1 month
Set the printer to Hibernate mode even if there is an active Ethernet connection.
Hibernate Timeout on Connection
Hibernate Do Not Hibernate

Understanding the printer menus 65
Set the amount of time in seconds the printer waits to receive an end‑of‑job message before canceling the remainder of the print job.
Set the amount of time in seconds the printer waits for additional data before canceling a print job.
Automatically restart the printer back into the normal operation.
Reboot when idle Reboot always Reboot never
Determine the number of automatic restarts the printer can perform.
Let the printer automatically continue printing from certain offline situations when not resolved within the specified time period.
Specify whether the printer reprints jammed pages.

Understanding the printer menus 66
Successfully print a page that may not have printed otherwise.
Determine how the printer, while in idle state, reacts when you press the Sleep button for less than three seconds.
Do nothing Sleep Hibernate
Press and Hold Sleep Button
Determine how the printer, while in idle state, reacts when you press and hold the Sleep button for more than three seconds.
Do nothing Sleep Hibernate
Select a custom home message that appears as an alternating display of the printer status.
Off IP Address Hostname Contact Name Location Zero Configuration Name Custom Text [x]

Understanding the printer menus 67
Set the default printer language.
PCL Emulation PS Emulation
Set the logical and physical printable area.
Specify how the printer handles temporary downloads, such as fonts and macros stored in the RAM, when the printer receives a print job that requires more than the available memory.

Understanding the printer menus 68
Specify whether two‑sided (duplex) printing is set as the default for all print jobs.
1 sided 2 sided
For Windows users:
1 Click File > Print. 2 Click Properties, Preferences, Options, or Setup.
For Macintosh users:
1 Choose File > Print. 2 Adjust the settings from the print dialog and pop‑up menus.
Define the way two‑sided pages are bound and printed.
Long Edge Short Edge
1–999 Specify the default number of copies for each print job.
Specify whether to insert blank pages in a print job.
Do Not Print Print
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)
Specify whether to insert blank separator sheets.
Off Between Copies Between Jobs Between Pages
Specify the paper source for separator sheets.
Tray [x] Manual Feeder

Understanding the printer menus 69
Print multiple‑page images on one side of a paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Specify the positioning of multiple‑page images when using Paper Saver.
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify the orientation of a multiple‑page document.
Print a border when using Paper Saver.
Specify the printed output resolution in dots per inch.
300 dpi 600 dpi 1200 dpi 1200 Image Q 2400 Image Q
Enable more pixels to print in clusters for clarity, in order to enhance images horizontally or vertically, or to enhance fonts.
Off Fonts Horizontally Vertically Both directions Isolated
1–10 Lighten or darken the printed output.

Understanding the printer menus 70
Enable a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts.
Automatically adjust the contrast enhancement applied to images.
Adjust the printed output either by lightening or darkening it. You can conserve toner by lightening the output.
‑6 to 6
0–5 Adjust the contrast of printed objects.
Print a page containing the PostScript error.
Specify the orientation of text and graphics on the page.
Specify the number of lines that print on each page.

Understanding the printer menus 71
Set the printer to print on A4‑size paper.
198 mm 203 mm
Specify whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command.
Auto CR after LF
Specify whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command.
Auto LF after CR
Configure the printer to work with printer software or programs that use different source assignments for trays and feeders.
Off None 0–199 Assign Tray [x]
Off None 0–199 Assign Manual Paper
Off None 0–199 Assign Manual Env
View the factory default setting assigned to each tray or feeder.
MPF Default = 8 T1 Default = 1 T1 Default = 4 T1 Default = 5 T1 Default = 20 T1 Default = 21 Env Default = 6 MPaper Default = 2 MEnv Default = 3

Understanding the printer menus 72
Restore all tray and feeder assignments to the factory default settings.
Current Date and Time View the current date and time settings for the printer.
Manually Set Date and Time
Enter the date and time.
Select the time zone.
[list of time zones]
Set the printer to use the applicable daylight saving time (DST) start and end times associated with the printer Time Zone setting.
Set the time offset from Coordinated Universal Time or Greenwich Mean Time.
[input time in minutes]
Set the DST start time.
[list of weeks] [list of days] [list of months] [input time]
Set DST end time.
[list of weeks] [list of days] [list of months] [input time]
Set the DST offset time.
[input time in minutes]

Saving money and the environment 73
Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impact on the environment. We design with the environment in mind, engineer our packaging to reduce materials, and provide collection and recycling programs. For more information, see:
By selecting certain printer settings or tasks, you may be able to reduce your printer's impact even further. This chapter outlines the settings and tasks that may yield a greater environmental benefit.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser/LED printers. For more information on recycled papers that work well with your printer, see “Using recycled paper and other office papers” on page 43.
There are a number of ways you can reduce the amount of paper and toner you use when printing. You can:
If your printer model supports duplex printing, you can control whether print appears on one or two sides of the paper by selecting 2‑sided printing from the Print dialog or the Lexmark Toolbar.
You can print up to 16 consecutive pages of a multiple‑page document onto one side of a single sheet of paper by selecting a setting from the Multipage printing (N‑Up) section of the Print dialog.
Before printing or making multiple copies of a document:
Carefully select and load paper to avoid paper jams. For more information, see “Avoiding jams” on page 92.

Saving money and the environment 74
If your printer is connected to a computer by a USB or parallel cable, then use the Local Printer Settings Utility for Windows or Printer Settings for Macintosh. If your printer is connected to the network, then use the Embedded Web Server.
Sleep mode saves energy by lowering power consumption during extended periods of inactivity.
Hibernate mode is an ultra‑low‑power operating mode. When operating in Hibernate mode, all other systems and devices are powered down safely. When in Hibernate mode, the printer does not respond to print jobs.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Sleep Button Settings.
3 From the “Press Sleep Button” or “Press and Hold Sleep Button” menu, select Sleep or Hibernate.
4 Click Submit.
Depending on your operating system, access the Setup menu using the Local Printer Settings Utility or the Sleep Mode menu using the Printer Settings.
To save energy, decrease the number of minutes the printer waits before it enters Sleep Mode.
Available settings range from 1 to 120 minutes. The factory default setting is 30 minutes.
1 Open a Web browser, and then type the printer IP address in the address field.

Saving money and the environment 75
2 Click Settings > General Settings > Timeouts.
3 In the Sleep Mode field, enter the number of minutes you want the printer to wait before it enters Sleep Mode.
4 Click Submit.
Hibernate Timeout lets you set the amount of time the printer waits after a print job is processed before it goes into a reduced power state.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Timeouts.
3 From the Hibernate Timeout menu, select the number of hours, days, weeks, or months you want for the printer to wait before it goes into a reduced power state.
4 Click Submit.
Depending on your operating system, access the Hibernate Timeout menu using the Local Printer Settings Utility or Print Settings.
Schedule Power Modes lets the user schedule when the printer goes into a reduced power state or into the Ready state.
1 Open a Web browser, and then type the printer IP address in the address field.

Saving money and the environment 76
2 Click Settings > General Settings > Schedule Power Modes.
3 From the Action menu, select the power mode.
4 From the Time menu, select the time.
5 From the Day(s) menu, select the day or days.
6 Click Add.
Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information, see:
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country or region from the list.
3 Follow the instructions on the computer screen.
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark will recycle the box.

Saving money and the environment 77
Lexmark Cartridge Collection Program diverts millions of Lexmark cartridges from landfills annually by making it both easy and free for Lexmark customers to return used cartridges to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. Boxes used to return the cartridges are also recycled.
To return Lexmark cartridges for reuse or recycling, follow the instructions that came with your printer or cartridge and use the prepaid shipping label. You can also do the following:
1 Go to www.lexmark.com/recycle.
2 From the Toner Cartridges section, select your country or region.
3 Follow the instructions on the computer screen.

Securing the printer 78
Using the security lock feature
The printer is equipped with a security lock feature. Attach a security lock compatible with most laptop computers in the location shown to secure the printer in place.


Your printer contains various types of memory that can store device and network settings, and user data.
Type of memory Description
Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print jobs.
Non-volatile memory Your printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store operating system, device settings, and network information.
Erase the content of any installed printer memory in the following circumstances:

Securing the printer 79
The volatile memory (RAM) installed in your printer requires a power source to retain information. To erase the buffered data, simply turn off the printer.
1 Turn off the printer.
2 Open the front door of the printer and hold down while turning the printer on. Release only when the printer control panel light sequence matches the light sequence in the following illustration.

Securing the printer 80
3 Press until the printer control panel light sequence matches the light sequence in the following illustration,
and then press .
The printer will restart several times during this process.
4 Close the front door.
In high-security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer cannot be accessed by unauthorized persons. For more information, visit the Lexmark security Web page.
You can also see the Embedded Web Server — Security: Administrator’s Guide for additional information:
1 Go to www.lexmark.com, and then navigate to Support & Downloads > select your printer.
2 Click the Manuals tab, and then select Embedded Web Server — Security: Administrator’s Guide.
‑ Blinking · ‑ Blinking

Maintaining the printer 81
1 Make sure that the printer is turned off and unplugged from the electrical outlet.
2 Remove paper from the standard bin and multipurpose feeder.
3 Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.
4 Dampen a clean, lint-free cloth with water, and use it to wipe the outside of the printer.
5 Make sure all areas of the printer are dry before sending a new print job.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Device Status > More Details.

Maintaining the printer 82
From the printer control panel, press , and then check the supply and part status in the Supply Information section.
The estimated number of remaining pages is based on the recent printing history of the printer. Its accuracy may vary significantly and is dependent on many factors, such as actual document content, print quality settings, and other printer settings.
The accuracy of the estimated number of remaining pages may decrease when the actual printing consumption is different from the historical printing consumption. Consider the variable level of accuracy before purchasing or replacing supplies based on the estimate. Until an adequate print history is obtained on the printer, initial estimates assume future supplies consumption based on the International Organization for Standardization* test methods and page content.
* Average continuous black declared cartridge yield in accordance with ISO/IEC 19752.
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, visit the Lexmark Web Site at www.lexmark.com or contact the place where you purchased the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. Use of third-party supplies or parts can affect warranty coverage. Damage caused by the use of third-party supplies or parts is not covered by the warranty. All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.

Maintaining the printer 83
Item Return Program cartridge
For the United States and Canada
High Yield Toner Cartridge 501H
Extra High Yield Toner Cartridge 501X1
Ultra High Yield Toner Cartridge 501U2
For the European Union, European Economic Area , and Switzerland
High Yield Toner Cartridge 502H
Extra High Yield Toner Cartridge 502X1
Ultra High Yield Toner Cartridge 502U2
For the Asia Pacific Region (includes Australia and New Zealand)
High Yield Toner Cartridge 503H
Extra High Yield Toner Cartridge 503X1
Ultra High Yield Toner Cartridge 503U2
For Latin America (includes Puerto Rico and Mexico)
High Yield Toner Cartridge 504H
Extra High Yield Toner Cartridge 504X1
Ultra High Yield Toner Cartridge 504U2
For Africa, Middle East, Central Eastern Europe, and Commonwealth of Independent States
High Yield Toner Cartridge 505H
Extra High Yield Toner Cartridge 505X1
Ultra High Yield Toner Cartridge 505U2
1 This cartridge is supported only in MS410d, MS410dn, MS510dn, MS610dn, and MS610de printer models.
2 This cartridge is supported only in MS510dn, MS610dn, and MS610de printer models.
For more information on countries located in each region, visit www.lexmark.com/regions.
High Yield Toner Cartridge 500HA1
1 This cartridge is supported only in MS310d and MS310dn printer models.
2 This cartridge is supported only in MS410d and MS410dn printer models.
3 This cartridge is supported only in MS510dn, MS610dn, and MS610de printer models.

Maintaining the printer 84
Extra High Yield Toner Cartridge 500XA2
Ultra High Yield Toner Cartridge 500UA3
1 This cartridge is supported only in MS310d and MS310dn printer models.
2 This cartridge is supported only in MS410d and MS410dn printer models.
3 This cartridge is supported only in MS510dn, MS610dn, and MS610de printer models.
Extremely low print coverage for extended periods of time may cause imaging unit parts to fail prior to exhaustion of toner from toner cartridge.
For more information on replacing the imaging unit, see the instruction sheet that came with the supply.
Part name Lexmark Return Program Regular
Imaging unit 500Z 500ZA
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:
Item Regular cartridge

Maintaining the printer 85
1 Press the button on the right side of the printer, and then open the front door.


2 Pull the toner cartridge out using the handle.

3 Unpack the toner cartridge, and then remove all packing materials.
4 Shake the new cartridge to redistribute the toner.

5 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.

Maintaining the printer 86


6 Close the front door.
1 Press the button on the right side of the printer, and then open the front door.
2 Pull the toner cartridge out using the handle.

Maintaining the printer 87
3 Lift the green handle, and then pull the imaging unit out of the printer.

4 Unpack the new imaging unit, and then shake it.

5 Remove all packing materials from the imaging unit.


Maintaining the printer 88
6 Insert the imaging unit into the printer by aligning the arrows on the side rails of the imaging unit with the arrows on the side rails inside the printer.


7 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.
8 Close the front door.

Maintaining the printer 89


Use only the power cord provided with this product or the manufacturer's authorized replacement.
The printer and its hardware options can be safely moved to another location by following these precautions:
When shipping the printer, use the original packaging.

Managing the printer 90
This chapter covers basic administrative support tasks using the Embedded Web Server.
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server Administrator's Guide on the Lexmark Web site at http://support.lexmark.com.
You can view some reports from the Embedded Web Server. These reports are useful for assessing the status of the printer, the network, and supplies.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Reports, and then click the type of report you want to view.
You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Supply Notifications.
3 From the drop‑down menu for each supply, select one of the following notification options:

Managing the printer 91
Off The normal printer behavior for all supplies occurs.
E‑mail Only The printer generates an e-mail when the supply condition is reached. The status of the supply appears on the menus page and status page.
Continuable Stop1 The printer stops processing jobs when the supply condition is reached. The user needs to press a button to continue printing.
Non Continuable Stop1,2 The printer stops when the supply condition is reached. The supply must be replaced to continue printing.
1The printer generates an e-mail about the status of the supply when supply notification is enabled.
2The printer stops when some supplies become empty to prevent damage.
4 Click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click the Copy Printer Settings tab.
3 If you want to change the language, then select a language from the drop‑down menu, and then click Click here to submit language.
4 Click the Printer Settings tab.
5 Type the IP addresses of the source and target printers in their appropriate fields.
6 Click Copy Printer Settings.
Notification Description

Carefully select paper and specialty media and load them properly to avoid most jams. For more information, see “Avoiding jams” on page 92. If jams do occur, then follow the steps outlined in this chapter.
Correct loading of paper Incorrect loading of paper


Clearing jams 92




Open the doors and pull out the trays to access jam areas.
Clearing jams 93
![Page 94 of the Lexmark 220 user manual — [x] ‑ page jam, open front door. [20y.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-94.webp?w=400)
![Lexmark 220 — [x]-page jam, open front door. [20y.xx] diagram (page 94)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/rimg-48.webp)
![Lexmark 220 — [x]-page jam, open front door. [20y.xx] diagram (page 94)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/rimg-49.webp)
3 Standard 250‑sheet tray (Tray 1)
4 Optional 250‑ or 550‑sheet tray (Tray 2)
5 Multipurpose feeder door
![Page 95 of the Lexmark 220 user manual — [x]-page jam, open front door. [20y.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-95.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
If the supplemental light sequence matches the light sequence in the preceding illustration, then do the following.
![Page 96 of the Lexmark 220 user manual — [x]-page jam, open front door. [20y.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-96.webp?w=400)
1 Press the button on the right side of the printer, and then open the front door.
2 Pull out the toner cartridge using the handle.
3 Lift the green handle, and then pull out the imaging unit from the printer.
Clearing jams 96
![Page 97 of the Lexmark 220 user manual — [x]-page jam, open front door. [20y.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-97.webp?w=400)
4 Place the imaging unit aside on a flat, smooth surface.
5 Lift the green flap in front of the printer.
![Lexmark 220 — [x]-page jam, open front door. [20y.xx] diagram (page 97)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/rimg-50.webp)
6 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark 220 — [x]-page jam, open front door. [20y.xx] diagram (page 97)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/rimg-51.webp)
Clearing jams 97
![Page 98 of the Lexmark 220 user manual — [x]-page jam, open front door. [20y.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-98.webp?w=400)
7 Insert the imaging unit by aligning the arrows on the side rails of the unit with the arrows on the side rails inside the printer, and then insert the imaging unit into the printer.
8 Insert the toner cartridge by aligning the side rails of the cartridge with the arrows on the side rails inside the printer, and then insert the cartridge into the printer.
9 Close the front door.
10 From the printer control panel, press to clear the message and continue printing.
Clearing jams 98
![Page 99 of the Lexmark 220 user manual — [x] ‑ page jam, open rear door. [20y.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-99.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
![Page 100 of the Lexmark 220 user manual — [x]-page jam, open rear door. [20y.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-100.webp?w=400)
If the supplemental light sequence matches the light sequence in the preceding illustration, then do the following.
1 Press the button on the right side of the printer, and then open the front door.
2 Gently pull down the rear door.
![Lexmark 220 — [x]-page jam, open rear door. [20y.xx] diagram (page 100)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/rimg-52.webp)
3 Firmly grasp the jammed paper on each side, and then gently pull it out.
Clearing jams 100
![Page 101 of the Lexmark 220 user manual — [x] ‑ page jam, clear standard bin. [20y.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-101.webp?w=400)
4 Close the rear and front doors.
5 From the printer control panel, press to clear the message and continue printing.
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
Clearing jams 101 · ‑ On · ‑ On
![Page 102 of the Lexmark 220 user manual — [x]-page jam, clear standard bin. [20y.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-102.webp?w=400)
If the supplemental light sequence matches the light sequence in the preceding illustration, then do the following.
1 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark 220 — [x]-page jam, clear standard bin. [20y.xx] diagram (page 102)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/rimg-53.webp)
2 From the printer control panel, press to clear the message and continue printing.

If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.

![Page 104 of the Lexmark 220 user manual — [x]-page jam, remove tray 1 to clear duplex. [23y.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-104.webp?w=400)
If the supplemental light sequence matches any of the light sequences in the preceding illustrations, then do the following.
1 Pull out the tray completely.
![Lexmark 220 — [x]-page jam, remove tray 1 to clear duplex. [23y.xx] diagram (page 104)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/rimg-55.webp)
![Page 105 of the Lexmark 220 user manual — [x]-page jam, remove tray 1 to clear duplex. [23y.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-105.webp?w=400)
2 Locate the blue lever, and then pull it down to release the jam.
![Lexmark 220 — [x]-page jam, remove tray 1 to clear duplex. [23y.xx] diagram (page 105)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/rimg-56.webp)
![Lexmark 220 — [x]-page jam, remove tray 1 to clear duplex. [23y.xx] diagram (page 105)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/rimg-57.webp)
3 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark 220 — [x]-page jam, remove tray 1 to clear duplex. [23y.xx] diagram (page 105)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/rimg-58.webp)
4 Insert the tray.
5 From the printer control panel, press to clear the message and continue printing.
Clearing jams 105

If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
![Page 107 of the Lexmark 220 user manual — [x]-page jam, remove tray [x]. [24y.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-107.webp?w=400)
If the supplemental light sequence matches any of the light sequences in the preceding illustrations, then do the following.
1 Pull out the tray completely.
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark 220 — [x]-page jam, remove tray [x]. [24y.xx] diagram (page 107)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/rimg-59.webp)
![Page 108 of the Lexmark 220 user manual — [x] ‑ page jam, clear manual feeder. [250.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-108.webp?w=400)
3 Insert the tray.
4 From the printer control panel, press to clear the message and continue printing.
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
Clearing jams 108 · ‑ On · ‑ On
![Page 109 of the Lexmark 220 user manual — [x]-page jam, clear manual feeder. [250.xx]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-109.webp?w=400)
If the supplemental light sequence matches the light sequence in the preceding illustration, then do the following.
1 From the multipurpose feeder, firmly grasp the jammed paper on each side, and then gently pull it out.
2 Flex the sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.
![Lexmark 220 — [x]-page jam, clear manual feeder. [250.xx] diagram (page 109)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/fig-109-1.webp)
3 Reload paper into the multipurpose feeder.
![Lexmark 220 — [x]-page jam, clear manual feeder. [250.xx] diagram (page 109)](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/rimg-60.webp)
4 From the printer control panel, press to clear the message and continue printing.
![Page 110 of the Lexmark 220 user manual — Cartridge, imaging unit mismatch [41.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-110.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then do the following:
1 Check if both the toner cartridge and imaging unit are MICR (Magnetic Ink Character Recognition) or non-MICR supplies.
2 Change the toner cartridge or imaging unit so that both are MICR or non‑MICR supplies.
‑ On · ‑ On
![Page 111 of the Lexmark 220 user manual — Cartridge nearly low [88.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-111.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then you may need
to order a toner cartridge. If necessary, press on the printer control panel to continue printing.
‑ On · ‑ On · ‑ Slowly blinking
![Page 112 of the Lexmark 220 user manual — Non-Lexmark cartridge, see User’s Guide [33.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-112.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press on the printer control panel, if necessary, to continue printing.
If the printer control panel light sequence matches the light sequence in the preceding illustration, then you may need to replace the toner cartridge very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, press on the printer control panel to continue printing.
If the printer control panel lights blink from left to right repeatedly, then the printer has detected a non‑Lexmark cartridge installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components.
![Page 113 of the Lexmark 220 user manual — Replace cartridge, 0 estimated pages remain [88.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-113.webp?w=400)
All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or associated components.
To accept any and all of these risks and to proceed with the use of non-genuine supplies or parts in your printer,
press and simultaneously for at least three seconds to clear the light sequence.
‑ On · ‑ On
![Page 114 of the Lexmark 220 user manual — Replace cartridge, 0 estimated pages remain [88.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-114.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
If the supplemental light sequence matches the light sequence in the preceding illustration, then replace the toner cartridge. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
‑ On · ‑ Blinking · ‑ On
![Page 115 of the Lexmark 220 user manual — Replace cartridge, printer region mismatch [42.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-115.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
![Page 116 of the Lexmark 220 user manual — Reinstall missing or unresponsive cartridge [31.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-116.webp?w=400)
If the supplemental light sequence matches the light sequence in the preceding illustration, then install a toner cartridge that matches the region number of the printer. x indicates the value of the printer region. y indicates the value of the cartridge region. x and y can have the following values.
Region number (x) Region (y)
1 United States, Canada
2 European Economic Area (EEA), Switzerland
3 Asia Pacific, Australia, New Zealand
5 Africa, Middle East, rest of Europe
![Page 117 of the Lexmark 220 user manual — Reinstall missing or unresponsive cartridge [31.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-117.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
‑ On · ‑ On · ‑ On
![Page 118 of the Lexmark 220 user manual — Replace unsupported cartridge [32.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-118.webp?w=400)
If the printer control panel light sequence matches the preceding light sequence, then remove the toner cartridge, and then install a supported one. For more information, see the instruction sheet that came with the supply.
![Page 119 of the Lexmark 220 user manual — Imaging unit nearly low [84.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-119.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then you may need
to order an imaging unit. If necessary, press on the printer control panel to continue printing.
‑ Blinking · ‑ On
![Page 120 of the Lexmark 220 user manual — Non-Lexmark imaging unit, see User’s Guide [33.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-120.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press on the printer control panel, if necessary, to continue printing.
If the printer control panel light sequence matches the light sequence in the preceding illustration, then you may need to replace the imaging unit very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, press on the printer control panel to continue printing.
If the printer control panel lights blink from left to right repeatedly, then the printer has detected a non‑Lexmark imaging unit installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components.
![Page 121 of the Lexmark 220 user manual — Replace imaging unit, 0 estimated pages remain [84.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-121.webp?w=400)
All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or associated components.
To accept any and all of these risks and to proceed with the use of non-genuine supplies or parts in your printer,
press and simultaneously for at least four seconds to clear the light sequence.
If the printer control panel light sequence matches the light sequence in the preceding illustration, then replace the imaging unit. For more information, see the instruction sheet that came with the supply.
‑ On · ‑ Blinking · ‑ On
![Page 122 of the Lexmark 220 user manual — Reinstall missing or unresponsive imaging unit [31.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-122.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
![Page 123 of the Lexmark 220 user manual — Replace unsupported imaging unit [32.xy]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-123.webp?w=400)
If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
If the printer control panel light sequence matches the light sequence in the preceding illustration, then remove the imaging unit, and then install a supported one. For more information, see the instruction sheet that came with the supply.
![Page 124 of the Lexmark 220 user manual — Incorrect paper size, open [paper source] [34]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-124.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
‑ On · ‑ On · ‑ On
![Page 125 of the Lexmark 220 user manual — Load [paper source] with [custom type name] [orientation]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-125.webp?w=400)
If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
1 Open a Web browser, and then type the printer IP address in the address field.
Local Printer Settings Utility for Windows or through Printer Settings for Macintosh.
![Page 126 of the Lexmark 220 user manual — Load [paper source] with [custom type string] [orientation]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-126.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
If the printer control panel light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
‑ On · ‑ On · ‑ On
![Page 127 of the Lexmark 220 user manual — Load [paper source] with [paper size] [orientation]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-127.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
‑ On · ‑ On
![Page 128 of the Lexmark 220 user manual — Load [paper source] with [paper type] [paper size] [orientation]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-128.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
‑ On · ‑ On
![Page 129 of the Lexmark 220 user manual — Load Manual Feeder with [custom type name] [orientation]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-129.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
‑ On · ‑ On
![Page 130 of the Lexmark 220 user manual — Load Manual Feeder with [custom type string] [orientation]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-130.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
‑ On · ‑ On
![Page 131 of the Lexmark 220 user manual — Load Manual Feeder with [paper size] [orientation]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-131.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
‑ On · ‑ On
![Page 132 of the Lexmark 220 user manual — Load Manual Feeder with [paper type] [paper size] [orientation]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-132.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
‑ On · ‑ On
![Page 133 of the Lexmark 220 user manual — Network [x] software error [54]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-133.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then do the following:
1 Remove the paper stack from the standard output bin.
2 From the printer control panel, press to continue printing.
‑ Blinking

If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
![Page 135 of the Lexmark 220 user manual — Standard parallel port disabled [56]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-135.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
![Page 136 of the Lexmark 220 user manual — Standard network software error [54]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-136.webp?w=400)
If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
1 Open a Web browser, and then type the printer IP address in the address field.
Local Printer Settings Utility for Windows or through Printer Settings for Macintosh.
‑ On · ‑ On · ‑ On
![Page 137 of the Lexmark 220 user manual — Standard network software error [54]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-137.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
‑ On · ‑ On · ‑ On
![Page 138 of the Lexmark 220 user manual — Rear USB port disabled [56]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-138.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
![Page 139 of the Lexmark 220 user manual — Insufficient memory to collate job [37]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-139.webp?w=400)
If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
1 Open a Web browser, and then type the printer IP address in the address field.
Printer Settings Utility for Windows.
‑ On · ‑ On · ‑ On

If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
‑ On · ‑ On · ‑ On
![Page 141 of the Lexmark 220 user manual — Insufficient memory to support Resource Save feature [35]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-141.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
![Page 142 of the Lexmark 220 user manual — Memory full [38]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-142.webp?w=400)
If the supplemental light sequence matches the light sequence in the preceding illustration, then press on the printer control panel to clear the light sequence.
The job will be printed without using Resource Save.
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
‑ On · ‑ On

If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
If the printer control light sequence matches the light sequence in the preceding illustration, then close the front door of the printer.
![Page 144 of the Lexmark 220 user manual — Complex page, some data may not have printed [39]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-144.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
![Page 145 of the Lexmark 220 user manual — PPDS font error [50]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-145.webp?w=400)
If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
‑ On · ‑ On
![Page 146 of the Lexmark 220 user manual — PPDS font error [50]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-146.webp?w=400)
If the printer control light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.
If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more of the following:
‑ On · ‑ Blinking · ‑ On

Printer had to restart. Last job may be incomplete.
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press on the printer control panel to continue printing.
For more information, visit http://support.lexmark.com or contact customer support.

If the printer control panel light sequence matches the light sequence in the preceding illustration, then turn off the printer, and then turn it back on.
If the lights are still blinking after 10 seconds, then the printer may need to be serviced. Visit http://support.lexmark.com or contact your system support person.
![Page 149 of the Lexmark 220 user manual — Too many trays attached [58]](/cdn/reader/50/500e1d0da94c7cf802b6bb6e6f4ec7d5fbb6ed133ab44f0ca055fe13b60cfb4f/images/page-149.webp?w=400)
If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence.

If the supplemental light sequence matches the light sequence in the preceding illustration, then do the following:
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra tray or trays.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Go to step 2. Turn on the printer.
Make sure the printer is turned on.
Is the printer turned on?
Press the Sleep button to wake the printer from Sleep mode or Hibernate mode.
Go to step 3.
Check if the printer is in Sleep mode or Hibernate mode.
Is the printer in Sleep mode or Hibernate mode?
Go to step 4. Plug one end of the power cord into the printer and the other to a properly grounded electrical outlet.
Check if one end of the power cord is plugged into the printer and the other to a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
Unplug the other electrical equipment, and then turn on the printer. If the printer does not work, then reconnect the other electrical equipment.
Go to step 5.
Check other electrical equipment plugged into the electrical outlet.
Does other electrical equipment work?

Go to step 6. Make sure to match the following:
Check if the cables connecting the printer and the computer are inserted in the correct ports.
Are the cables inserted in the correct ports?
Step 6 Make sure the electrical outlet is not turned off by a switch or breaker.
Turn on the switch or reset the breaker.
Go to step 7.
Is the electrical outlet turned off by a switch or breaker?
Connect the printer power cord directly to a properly grounded electrical outlet.
Go to step 8.
Check if the printer is plugged into any surge protectors, uninterruptible power supplies, or extension cords.
Is the printer plugged into any surge protectors, uninterruptible power supplies, or extension cords?
Step 8 Check if one end of the printer cable is plugged into a port on the printer and the other to the computer, print server, option, or other network device.
Go to step 9. Connect the printer cable securely to the printer and the computer, print server, option, or other network device.
Is the printer cable securely attached to the printer and the computer, print server, option, or other network device?
Go to step 10. Turn off the printer, remove all packing materials, then reinstall the hardware options, and then turn on the printer.
Make sure to install all hardware options properly and remove any packing material.
Are all hardware options properly installed and all packing material removed?
Go to step 11. Use correct printer driver settings.
Check if you have selected the correct port settings in the printer driver.
Are the port settings correct?
Go to step 12. Install the correct printer driver.
Check the installed printer driver.
Is the correct printer driver installed?
The problem is solved. Contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Is the printer working?

The problem is solved. Go to step 2.
Turn off the printer, then wait for about 10 seconds, and then turn on the printer.
Does the internal option operate correctly?
Go to step 3. Connect the internal option to the controller board.
Check if the internal option is properly installed in the controller board.
a Turn off the printer using the power switch, and then unplug the power
cord from the electrical outlet. b Make sure the internal option is installed in the appropriate connector
in the controller board. c Connect the power cord to the printer, then to a properly grounded
electrical outlet, and then turn on the printer.
Is the internal option properly installed in the controller board?
Go to step 4. Reinstall the internal option.
Print a menu settings page, and then check to see if the internal option is listed in the Installed Features list.
Is the internal option listed in the menu settings page?
The problem is solved. Contact customer support.
a Check if the internal option is selected.
It may be necessary to manually add the internal option in the printer driver to make it available for print jobs. For more information, see “Updating available options in the printer driver” on page 21. b Resend the print job.
Does the internal option operate correctly?

The problem is solved. Go to step 2.
a Open the tray and do one or more of the following:
Is the tray working?
The problem is solved. Go to step 3.
a Turn off the printer, then wait about 10 seconds, and then turn the
printer back on. b Resend the print job.
Is the tray working?
Go to step 4. Reinstall the tray. For more information, see the setup documentation that came with the tray.
Check if the tray is installed.
Print a menu settings page, and then check if the tray is listed in the Installed Options list.
Is the tray listed in the menu settings page?
Go to step 5. Manually add the tray in the printer driver.
Check if the tray is available in the printer driver.
Is the tray available in the printer driver?
The problem is solved. Contact customer support.
Check if the option is selected.
a From the application you are using, select the option. For Mac OS X
version 9 users, make sure the printer is set up in Chooser. b Resend the print job.
Is the tray working?

Go to step 2. The problem is solved.
a Pull out the tray, and then do one or more of the following:
If jam recovery is enabled, then the print jobs will reprint automatically.
Do paper jams still occur frequently?
Go to step 3. The problem is solved.
a Load paper from a fresh package.
Do paper jams still occur frequently?
Contact customer support.
The problem is solved.
a Review the tips on avoiding jams. For more information, see “Avoiding
jams” on page 92. b Follow the recommendations, and then resend the print job.
Do paper jams still occur frequently?
Open front door and remove all trays.
Contact customer support.
The problem is solved.
a Clear any jammed pages.
b Press to clear the message and continue printing.
Does the paper jam message remain?

a From the Print Recovery menu, set Jam Recovery to Auto or On. To
The problem is solved. Contact customer support.
access the Print Recovery menu, try one or more of the following:
Note: If you do not know the IP address of the printer, then print a network setup page and locate the IP address in the TCP/IP section. • If the printer is connected to a computer by a USB or parallel cable, then open the Local Printer Settings Utility for Windows or the Printer Settings for Macintosh. b Resend the pages that did not print.
Were the jammed pages reprinted?
The problem is solved. Go to step 2.
a From the document you are trying to print, open the Print dialog and
check if you have selected the correct printer.
Do the jobs print?
Actions Yes No · Action Yes No · Step 1

The problem is solved. Go to step 3.
a Check if the printer is plugged in and turned on, and if the printer
control panel light sequence matches the light sequence in the following illustration:
‑ On b Resend the print job.
Do the jobs print?
The problem is solved. Go to step 4.
If printer control panel light sequence indicates an error, then clear the message. For more information on printer control panel error light sequences, see “Understanding the printer messages” on page 110.
Do the jobs print?
The problem is solved. Go to step 5.
a Check if the ports (USB, serial, or Ethernet) are working and if the
cables are securely connected to the computer and the printer.
Do the jobs print?
The problem is solved. Go to step 6.
a Turn off the printer, then wait for about 10 seconds, and then turn the
printer back on. b Resend the print job.
Do the jobs print?

The problem is solved. Contact customer support.
a Remove and reinstall the printer software. For more information, see
“Installing the printer software” on page 19.
Do the jobs print?
Place letter‑ or A4‑size paper in the tray, and then resend the print job.
The problem is solved. Contact customer
Does the print speed increase?
support.
Go to step 2. The problem is solved.
Reduce the number and size of fonts, the number and complexity of images, and the number of pages in the print job, and then resend the print job.
Does the print job still take longer than expected?
Go to step 3. The problem is solved.
From the Print Recovery menu, disable the Page Protect feature. To access the Print Recovery menu, do either of the following:
Does the print job still take longer than expected?

Install additional printer memory.
The problem is solved.
From the Eco‑Mode menu, change the environmental settings. To access the Eco‑Mode menu, do either of the following:
For more information, contact customer support.
Does the print job still take longer than expected?
The problem is solved. Go to step 2.
a Check if you are printing on paper that is supported by the tray. b Resend the print job.
Does the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 3.
a From the Paper menu, set the paper size and type to match the paper
loaded in the tray. To access the Paper menu, do either of the following:
Note: If you do not know the IP address of the printer, then print a network setup page and locate the IP address in the TCP/IP section. • If the printer is connected to a computer by a USB or parallel cable, then open the Local Printer Settings Utility for Windows or Printer Settings for Macintosh. b Resend the print job.
Does the job print from the correct tray or on the correct paper?

The problem is solved. Contact customer support.
a Depending on your operating system, open Printing Preferences or
the Print dialog, and then specify the paper type. b Resend the print job.
Does the job print from the correct tray or on the correct paper?
Turn off the printer, and then turn it back on to deactivate Hex Trace mode.
Go to step 2.
Check if the printer control panel light sequence matches the light sequence in the following illustration:
Do both light sequences match?
Contact customer support.
The problem is solved.
a Open a Web browser, and then type the printer IP address in the
address field. b Click Settings > Network/Ports, and then click Standard Network or
Network [x]. c Select PCL SmartSwitch or PS SmartSwitch, and then click Submit. d Resend the print job.
Do incorrect characters print?

a From the Paper menu, set the paper size and type to match the paper
The problem is solved. Contact customer support.
loaded in the trays to be linked. To access the Paper menu, do either of the following:
Do the trays link correctly?
The problem is solved. Go to step 2.
a From the Finishing menu, set Collate to On. To access the Finishing
menu, do either of the following:
Note: If you do not know the IP address of the printer, then print a network setup page and locate the IP address in the TCP/IP section. • If the printer is connected to a computer by a USB or parallel cable, then open the Local Printer Settings Utility for Windows or Printer Settings for Macintosh. b Resend the print job.
Does the job print and collate correctly?
The problem is solved. Go to step 3.
a From the printer software, set Collate to On.
Does the job print and collate correctly?

The problem is solved. Contact customer support.
Reduce the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Does the job print and collate correctly?
Step 1 From the Setup menu, adjust the print timeout setting. To access the Setup menu, do either of the following:
The problem is solved. Go to step 2.
address field.
Settings > General Settings > Timeouts > adjust the print timeout setting > Submit • If the printer is connected to a computer by a USB or parallel cable, then open the Local Printer Settings Utility for Windows or Printer Settings for Macintosh.
Does the file print correctly?
The problem is solved. Contact customer support.
a Check the original file for manual page breaks. b Resend the print job.
Does the file print correctly?

Go to step 2. The problem is solved.
a Check if there is packing material left on the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Check if the packing material is properly removed from the imaging unit.
Is the printer still printing blank pages?
Go to step 3. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Is the printer still printing blank pages?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the printer still printing blank pages?
ABCDE ABCDE ABCDE

Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the paper loaded. b Resend the print job.
Is the page or image clipped?
Go to step 3. Do one or more of the following:
From the Paper menu, set the paper size and type to match the paper loaded in the tray. To access the Paper menu, do either of the following:
Do the paper size and type settings match the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper size and type
from Printing Preferences or the Print dialog. b Resend the print job.
Is the page or image clipped?
Contact customer support.
The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge. 2 Remove the imaging unit.
Is the page or image clipped?


Go to step 2. Load paper with the correct paper type and weight in the tray.
Check if the paper loaded in the tray has the correct paper type and weight.
Is paper with the correct paper type and weight loaded in the tray?
Go to step 3. Change the paper type and weight to match the paper loaded in the tray.
From the Paper menu, set the paper size and type to match the paper loaded in the tray. To access the Paper menu, do either of the following:
Do the paper type and weight settings match the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or the Print dialog. b Resend the print job.
Do shadow images still appear on the prints?
Step 4 Replace the imaging unit, and then resend the print job.
Contact customer support.
The problem is solved.
Do shadow images still appear on the prints?
ABCDE
ABCDE ABCDE

The problem is solved. Go to step 2.
a From the Quality menu, select a lower number to reduce the toner
density. To access the Quality menu, do either of the following:
Does the gray background disappear from the prints?
The problem is solved. Contact customer support.
Reinstall the imaging unit and the toner cartridge.
a Remove the toner cartridge. b Remove the imaging unit.
Does the gray background disappear from the prints?
ABCD ABCD ABCD
The problem is solved. Go to step 2.
a Move the width and length guides in the tray to the correct positions
for the paper size loaded. b Resend the print job.
Are the margins correct?

Go to step 3. Do one or more of the following:
From the Paper menu, check if the paper size setting matches the paper loaded in the tray. To access the Paper menu, do either of the following:
Does the paper size setting match the paper loaded in the tray?
The problem is solved. Contact customer support.
a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.
Are the margins correct?
Go to step 2. Adjust the width and length guides.
Move the width and length guides in the tray to the correct positions for the size of the paper loaded.
Are the width and length guides positioned correctly?
Go to step 3. Change the paper type and weight to match the paper loaded in the tray.
From the Paper menu, set the paper size and type to match the paper loaded in the tray. To access the Paper menu, try one or more of the following:
Do the paper type and weight match the type and weight of the paper in the tray?


a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
a Remove the paper from the tray, and then turn it over. b Resend the print job.

a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded in the tray. b Resend the print job.

Go to step 3. Specify the correct paper type and weight to match the paper loaded in the tray.
From the Paper menu, set the paper size and type to match the paper loaded in the tray. To access the Paper menu, do either of the following:
Do the printer settings match the type and weight of the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or the Print dialog. b Resend the print job.
Do print irregularities still appear?
Action Yes No · Step 2 · Step 3

From the Paper Texture menu, change the texture settings. To access the Paper Texture menu, do either of the following:
Go to step 5.
Check if the paper loaded in the tray has texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Do print irregularities still appear?
Step 6 Replace the imaging unit, and then resend the print job.
Contact customer support at http://support.lexmar k.com or your service representative.
The problem is solved.
Do print irregularities still appear?
Action Yes No · Step 4 · Step 5

Go to step 2. 1 Check if the distance between the defects equal to 80 mm (3.15 in.) 2 Take note of the distance, and then contact customer support at http://support.le xmark.com or your service representative.
Measure the distance between the defects.
Check for a distance between the defects that equals:
Is the distance between defects equal to one of the listed measurements?
Contact customer support at http://support.lexma rk.com or your service representative.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do the repeating defects still appear?
ABC DEF ABC DEF
Action Yes No · Step 1 · Step 2

Go to step 2. The problem is solved.
a From the Quality menu, reduce the toner darkness. To access the
Quality menu, do either of the following:
Is the print still too dark?
Go to step 3. Change the paper type, texture, and weight to match the paper loaded in the tray.
a From the Paper Menu, check if the paper type, texture, and weight
match the paper loaded in the tray. To access the Paper Menu, do either of the following:
Note: If you do not know the IP address of the printer, then print a network setup page and locate the IP address in the TCP/IP section. • If the printer is connected to a computer by a USB or parallel cable, then open the Local Printer Settings Utility for Windows or Printer Settings for Macintosh. b Resend the print job.
Is the tray set to the type and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or the Print dialog. b Resend the print job.
Is the print still too dark?

From the Paper Texture menu, change the texture settings to match the paper you are printing on. To access the Paper Texture menu, do either of the following:
Go to step 5.
Check if the paper loaded in the tray has texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too dark?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the print still too dark?

ABC DEF
Go to step 2. The problem is solved.
a From the Quality menu, increase the toner darkness. To access the
Quality menu, do either of the following:
Is the print still too light?
Go to step 3. Change the paper type, texture, and weight to match the paper loaded in the tray.
a From the Paper Menu, check if the paper type, texture, and weight
match the paper loaded in the tray. To access the Paper Menu, do either of the following:
Note: If you do not know the IP address of the printer, then print a network setup page and locate the IP address in the TCP/IP section. • If the printer is connected to a computer by a USB or parallel cable, then open the Local Printer Settings Utility for Windows or Printer Settings for Macintosh. b Resend the print job.
Is the tray set to the type and weight of the paper loaded?
Action Yes No · Step 1 · Step 2

Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or the Print dialog. b Resend the print job.
Is the print still too light?
From the Paper Texture menu, change the texture settings to match the paper you are printing on. To access the Paper Texture menu, do either of the following:
Go to step 5.
Make sure that the paper has no texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too light?

Go to step 7. The problem is solved.
a Shake the imaging unit to redistribute the toner.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Is the print still too light?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the print still too light?
) ) ABCDE
ABCDE ABCDE
Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded. b Resend the print job.
Is the print still skewed?
Contact customer support.
The problem is solved.
a Check if you are printing on a paper that is supported by the tray. b Resend the print job.
Is the print still skewed?

Go to step 2. The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge, and then the imaging unit.
Is the printer printing solid black pages?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the printer printing solid black pages?
Go to step 2. Set the paper type to Transparency.
From the Paper Menu, set the paper type to match the paper loaded in the tray. To access the Paper Menu, do either of the following:
Is the paper type for the tray set to Transparency?

Contact customer support.
The problem is solved.
a Check if you are using a recommended type of transparency. b Resend the print job.
Is the print quality still poor?
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the tray or feeder from
Printing Preferences or the Print dialog. b Resend the print job.
Do streaked horizontal lines still appear on prints?
Go to step 3. Change the paper type and weight to match the paper loaded in the tray.
From the Paper Menu, set the paper type and weight to match the paper loaded in the tray. To access the Paper Menu, do either of the following:
Do the paper type and weight settings match the paper in the tray?
Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked horizontal lines still appear on prints?


1 Remove the toner cartridge, and then the imaging unit.
Replace the imaging unit, and then resend the print job.
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or the Print dialog. b Resend the print job.
Do streaked vertical lines still appear on prints?
Go to step 3. Change the paper type, texture, and weight to match the paper in the tray.
From the Paper Menu, set the paper type, texture, and weight to match the paper loaded in the tray. To access the Paper Menu, do either of the following:
Do the paper type, texture, and weight match the paper in the tray?


1 Remove the toner cartridge, and then the imaging unit.
Contact customer support at http://support.lexmar k.com or your service representative.
Replace the imaging unit, and then resend the print job.

a Make sure your software program is using a correct fill pattern. b Resend the print job.
a Load the specified tray or feeder with a recommended type of paper. b Resend the print job.


1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Replace the imaging unit, and then resend the print job.

a Make sure your software program is using a correct fill pattern. b Resend the print job.

Go to step 3. The problem is solved.
a From the Paper Menu, set the paper type and weight to match the
paper loaded in the tray. To access the Paper Menu, do either of the following:
Note: If you do not know the IP address of the printer, then print a network setup page and locate the IP address in the TCP/IP section. • If the printer is connected to a computer by a USB or parallel cable, then open the Local Printer Settings Utility for Windows or Printer Settings for Macintosh. b Resend the print job.
Do vertical voids still appear on prints?
Go to step 4. The problem is solved.
Check if you are using a recommended type of paper.
a Load the specified tray or feeder with a recommended type of paper. b Resend the print job.
Do vertical voids still appear on prints?
Contact customer support.
The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Do vertical voids appear on prints?
Replace the imaging unit, and then resend the print job.
Contact customer support.
The problem is solved.
Do toner specks appear on prints?

ABC DEF
Go to step 2. Specify the paper type, texture, and weight from the tray settings to match the paper loaded in the tray.
From the Paper menu on the printer control panel, check the paper type, texture, and weight. To access the Paper Menu, do either of the following:
Do the paper type, texture, and weight match the paper loaded in the tray?
Step 2 Resend the print job.
Contact customer support.
The problem is solved.
Does the toner still rub off?

ABCDE ABCDE ABCDE
Replace the imaging unit, and then resend the print job.

The problem is solved. Go to step 2.
a Turn on the printer. b Open a Web browser, and then type the printer IP address.
c Press Enter.
Does the Embedded Web Server open?
The problem is solved. Go to step 3.
Make sure the printer IP address is correct.
a View the printer IP address:
Does the Embedded Web Server open?
The problem is solved. Go to step 4.
Check if the network is working.
a Print a network setup page. b Check the first section of the network setup page and confirm that the
status is Connected.
Does the Embedded Web Server open?
The problem is solved. Go to step 5.
Check if the cable connections to the printer and print server are secure.
a Connect the cables properly. For more information, see the setup
documentation that came with the printer. b Open a Web browser, and then type the printer IP address.
c Press Enter.
Does the Embedded Web Server open?

The problem is solved. Contact your system support person.
Temporarily disable the Web proxy servers.
Proxy servers may block or restrict you from accessing certain Web sites including the Embedded Web Server.
Does the Embedded Web Server open?
When you contact customer support, describe the problem you are experiencing, the printer control panel light sequence, and the troubleshooting steps you have already taken to find a solution.
You need to know your printer model type and serial number. For more information, see the label on the inside top front cover of the printer. The serial number is also listed on the menu settings page.
Lexmark has various ways to help you solve your printing problem. Visit the Lexmark Web site at http://support.lexmark.com, and then select one of the following:
Tech Library You can browse our library of manuals, support documentation, drivers, and other downloads to help you
solve common problems.
E-mail You can send an e-mail to the Lexmark team, describing your problem. A service representative will respond and provide you with information to solve your problem.
Live chat You can chat directly with a service representative. They can work with you to solve your printer problem or provide assistance through Assisted Service where the service representative can remotely connect to your computer through the Internet to troubleshoot problems, install updates, or complete other tasks to help you successfully use your Lexmark product.
Telephone support is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, visit the Lexmark Web site at http://support.lexmark.com.
Action Yes No · Step 5

Product name:
Machine type:
Model(s):
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
© 2013 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
Lexmark MS310d, MS310dn · 220, 230 · May 2013

Lexmark, Lexmark with diamond design, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
All other trademarks are the property of their respective owners.
AirPrint and the AirPrint logo are trademarks of Apple, Inc.
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232–3000
This product may contain the following modular component(s):

Lexmark regulatory type/model LEX-M01-005; FCC ID: IYLLEXM01005; IC:2376A-M01005
All licensing notices associated with this product can be viewed from the root directory of the installation software CD.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Printing 53 dBA (one-sided); 52 dBA (two-sided)
Values are subject to change. See www.lexmark.com for current values.
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products.
If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.
Ready N/A

This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching the metal frame of the printer.
Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
Ambient operating temperature 16°C to 32°C (60°F to 90°F)
Shipping temperature -40 to 43.3°C (-40 to 110°F)
Storage temperature and relative humidity 2 to 35°C (34 to 95°F)
8 to 80% RH
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, Chapter I, Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 7 milliwatt gallium arsenide laser operating in the wavelength of 655-675 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
A laser notice label may be affixed to this printer as shown:

Opasnost - Nevidljivo lasersko zračenje kada su kasete uklonjene i poništena sigurnosna veza. Izbjegavati izlaganje zracima.
NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, ze zařízení je vysíláno neviditelné laserové záření. Nevystavujte se působení laserového paprsku.
FARE - Usynlig laserstråling, når patroner fjernes, og spærreanordningen er slået fra. Undgå at blive udsat for laserstrålen.
VAARA - Näkymätöntä lasersäteilyä on varottava, kun värikasetit on poistettu ja lukitus on auki. Vältä lasersäteelle altistumista.
ΚΙΝΔΥΝΟΣ - Έκλυση αόρατης ακτινοβολίας laser κατά την αφαίρεση των κασετών και την απασφάλιση της μανδάλωσης. Αποφεύγετε την έκθεση στην ακτινοβολία laser.
VESZÉLY – Nem látható lézersugárzás fordulhat elő a patronok eltávolításakor és a zárószerkezet felbontásakor. Kerülje a lézersugárnak való kitettséget. PERICOLO - Emissione di radiazioni laser invisibili durante la rimozione delle cartucce e del blocco. Evitare l´esposizione al raggio laser.
FARE – Usynlig laserstråling når kassettene tas ut og sperren er satt ut av spill. Unngå eksponering for laserstrålen.
ОПАСНО! Невидимое лазерное излучение при извлеченных картриджах и снятии блокировки. Избегайте воздействия лазерных лучей. Pozor – Nebezpečenstvo neviditeľného laserového žiarenia pri odobratých kazetách a odblokovanej poistke. Nevystavujte sa lúčom.
FARA – Osynlig laserstrålning när patroner tas ur och spärrmekanismen är upphävd. Undvik exponering för laserstrålen.
危险 - 当移除碳粉盒及互锁失效时会产生看不见的激光辐射,请避免暴露在激光光束下。
危険 - カートリッジが取り外され、内部ロックが無効になると、見えないレーザー光が放射されます。 このレーザー光に当たらないようにしてください。
Power consumption
Product power consumption
The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs. 520 W (one-sided); 340 W (two- sided)
Copy The product is generating hard‑copy output from hard‑copy original documents.
Scan The product is scanning hard‑copy documents. N/A
Ready The product is waiting for a print job. 8 W
Sleep Mode The product is in a high‑level energy‑saving mode. 5 W
Hibernate The product is in a low‑level energy‑saving mode. 0.5 W
Off The product is plugged into an electrical outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.

This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 30 min.
By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 120 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
This product is designed with an ultra‑low power operating mode called Hibernate mode. When operating in Hibernate Mode, all other systems and devices are powered down safely.
The Hibernate mode can be entered in any of the following methods:
Factory default Hibernate Timeout for this product in all countries or regions except for EU countries and Switzerland
Factory default value for this product in EU countries or regions and Switzerland 3 days
The amount of time the printer waits after a job is printed before it enters Hibernate mode can be modified between one hour and one month.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the electrical outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
Disabled

この装置は、クラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この 装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをしてください。
VCCI-B
European Community (EC) directives conformity
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and the ecodesign of energy- related products.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
This section contains the following regulatory information pertaining to wireless products that contain transmitters, for example, but not limited to, wireless network cards or proximity card readers.
The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.
This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb
The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.
Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement.
Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada.
En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.
Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur et loin des fenêtres afin de garantir une protection optimale.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc-sc.gc.ca/rpb
Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme aux spécifications techniques d'Industry Canada.
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, radio equipment and telecommunications terminal equipment and on the ecodesign of energy-related products.
Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.

Products equipped with 2.4GHz Wireless LAN option are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2009/125/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment and on the ecodesign of energy-related products.
Compliance is indicated by the CE marking.
Operation is allowed in all EU and EFTA countries, but is restricted to indoor use only.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product may be used in the countries indicated in the table below.

AT BE BG CH CY CZ DE DK EE
EL ES FI FR HR HU IE IS IT
LI LT LU LV MT NL NO PL PT
Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.
Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.
Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.
Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.
Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.
Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.
Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky
príslušné ustanovenia smernice 1999/5/ES.
Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
STATEMENT OF LIMITED WARRANTY FOR LEXMARK LASER PRINTERS, LEXMARK LED PRINTERS, AND LEXMARK MULTIFUNCTION LASER PRINTERS
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country- specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).

If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Transfer/Transport Units, Paper Feed items, if any, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
As part of your warranty service and/or replacement, Lexmark may update the firmware in your printer to the latest version. Firmware updates may modify printer settings and cause counterfeit and/or unauthorized products, supplies, parts, materials (such as toners and inks), software, or interfaces to stop working. Authorized use of genuine Lexmark products will not be impacted.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle

—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Elliptic Curve Cryptography (ECC) Cipher Suites for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Elliptic Curve Cipher Suites with SHA-256/382 and AES Galois Counter Mode (GCM) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Suite B Profile for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Addition of the Camellia Cipher Suites to Transport Layer Security (TLS) implemented in the product or service.

The use of certain patents in this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for AES-CCM ECC Cipher Suites for TLS implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for IKE and IKEv2 Authentication Using the Eliptic Curve Digital Signature Algorithm (ECDSA) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Suite B Cryptographic Suites for IPSec implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Algorithms for Internet Key Exchange version 1 (IKEv1) implemented in the product or service.




Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.