EN
Lexmark logo
Official user manual

Lexmark 10E

140 pages·1.5 MB·Printer·PDF·ENDEFRITNLJA
Lexmark 10E
Table of Contents 221 sections Contents · Safety information · About your printer · Thank you for choosing this printer! · … ShowHide
Contentsp.2Safety informationp.5About your printerp.6Thank you for choosing this printer!p.6Minimizing your printer's environmental impactp.6Finding information about the printerp.7Understanding the parts of the printerp.9Ordering and replacing suppliesp.11Ordering ink cartridgesp.11Using genuine Lexmark ink cartridgesp.11Replacing ink cartridgesp.12Ordering paper and other suppliesp.13Recycling Lexmark productsp.13Using the printer control panel buttons and menusp.14Using the printer control panelp.14Changing temporary settings into new default settingsp.15Changing the Power Saver timeoutp.16Saving energy with Eco-Modep.17Resetting to factory settingsp.17Using the printer softwarep.19Minimum system requirementsp.19Using the Windows printer softwarep.19Using the Macintosh printer softwarep.21Finding and installing optional softwarep.22Updating the printer software (Windows only)p.23Reinstalling the printer softwarep.23Uninstalling the printer softwarep.23Installing the printer softwarep.24Loading paper and original documentsp.25Loading paperp.25Saving paper default settingsp.27Loading original documents on the scanner glassp.28Printingp.29Tips for printingp.29Printing basic documentsp.29Printing a documentp.29Collating printed copiesp.30Printing pages in reverse orderp.30Printing multiple pages on one sheetp.31Printing documents from a memory card or flash drive (Windows only)p.32Printing specialty documentsp.33Printing envelopesp.33Printing labelsp.33Printing on custom-size paperp.34Printing on both sides of the paper (duplexing) manuallyp.35Working with photosp.37Using a memory card or flash drive with the printerp.37Supported memory cards and file typesp.38Printing photos using the printer control panelp.38Printing photos from a memory device using the printer softwarep.39Printing photos from a PictBridge-enabled digital camerap.40Printing photos from a memory device using the proof sheetp.41Printing photos from a digital camera using DPOFp.42Printing from a Bluetooth-enabled devicep.42Setting up a connection between your printer and a Bluetooth-enabled devicep.42Setting the Bluetooth security levelp.43Printing from a Bluetooth-enabled devicep.44Managing print jobsp.45Setting your printer as the default printerp.45Changing the printing modep.45Pausing print jobsp.46Resuming print jobsp.47Canceling print jobsp.47Copyingp.49Tips for copyingp.49Making copiesp.49Copying photosp.49Enlarging or reducing imagesp.50Adjusting copy qualityp.50Making a copy lighter or darkerp.50Collating copies using the printer control panelp.51Repeating an image on one pagep.51Copying multiple pages on one sheetp.52Making a duplex copy manuallyp.52Canceling copy jobsp.53Scanningp.54Tips for scanningp.54Scanning to a local or network computerp.54Scanning to a flash drive or memory cardp.55Scanning photos into an editing applicationp.55Scanning documents into an editing applicationp.57Scanning directly to e-mail using the printer softwarep.57Scanning to a PDFp.58Scanning FAQp.59How can I improve the quality of a scan?p.59How do I scan in black and white?p.59Why am I being asked for a PIN?p.59What is an application list, and how do I update it?p.59Canceling scan jobsp.60Networkingp.61Installing the printer on a wireless networkp.61Wireless network compatibilityp.61Supported network security optionsp.61Printing a network setup pagep.62Information you will need to set up the printer on a wireless networkp.62Installing the printer on a wireless networkp.63Installing the printer on other computersp.63Interpreting the colors of the Wi-Fi indicator lightp.64Special wireless installation instructionsp.64Assigning a static IP addressp.65Changing wireless settings after installationp.65Advanced wireless setupp.66Creating an ad hoc wireless networkp.66Adding a printer to an existing ad hoc wireless networkp.69Configuring the printer wirelessly using WPS (Wi-Fi Protected Setup)p.69Switching between USB and wireless connections (Windows only)p.70Switching between USB and wireless connections (Macintosh only)p.70Sharing a printer in a Windows environmentp.71Sharing a printer in a Macintosh environmentp.72Networking FAQp.73What is Wi-Fi Protected Setup?p.73Where do I find my WEP key or WPA passphrase?p.73What is an SSID?p.73Where do I find my SSID?p.74What is a network?p.74How do I find out what type of security my network is using?p.74How are home networks configured?p.74Why do I need an installation cable?p.76How do I attach the installation cable?p.76How are infrastructure and ad hoc networks different?p.77Finding the signal strengthp.78How can I improve wireless signal strength?p.78How can I make sure my computer and printer are connected to the same wireless network?p.79Can I use my printer on a USB and a network connection at the same time?p.81What is a MAC address?p.81How do I find the MAC address?p.81What is an IP address?p.82What is TCP/IP?p.82How do I locate IP addresses?p.82How are IP addresses assigned?p.83What is a key index?p.83Maintaining the printerp.84Maintaining ink cartridgesp.84Checking ink levelsp.84Aligning the printheadp.84Cleaning the printhead nozzlesp.85Cleaning the exterior of the printerp.86Cleaning the scanner glassp.86Troubleshootingp.87Before you troubleshootp.87Using the Service Center to solve printer problemsp.87If Troubleshooting does not solve your problemp.87Setup troubleshootingp.87Incorrect language appears on the displayp.88Printhead errorsp.88Software did not installp.90Print job does not print or is missing pagesp.90Printer is printing blank pagesp.91Printer is busy or does not respondp.91Cannot delete documents from the print queuep.92Cannot print through USBp.92Jams and misfeeds troubleshootingp.93Paper jam in the printerp.93Paper jam in the paper supportp.93Paper or specialty media misfeedsp.93Print troubleshootingp.94Poor quality at the edges of the pagep.94Streaks or lines on printed imagep.95Print speed is slowp.95Computer slows down when printingp.96Copy and scan troubleshootingp.96Copier or scanner does not respondp.96Scanner unit does not closep.96Poor copy or scanned image qualityp.96Partial copies or scans of documents or photosp.97Scan was not successfulp.97Scanning takes too long or freezes the computerp.97Cannot scan to a computer over a networkp.97Memory card troubleshootingp.98Memory card troubleshooting checklistp.98Nothing happens when a memory card is insertedp.98Cannot print documents from a memory card or flash drivep.98Photos do not transfer from a memory card across a wireless networkp.99Wireless troubleshootingp.99Wireless troubleshooting checklistp.99Resetting the wireless settings to factory defaultsp.100Cannot print over wireless networkp.100The Continue button is unavailablep.104Cannot print and there is a firewall on the computerp.105Wi-Fi indicator light is not litp.105Wi-Fi indicator light is green but the printer does not print (Windows only)p.106Wi-Fi indicator light is still orangep.107Wi-Fi indicator light is blinking orange during installationp.108Wireless print server not installedp.112“Communication not available” message displays when printing wirelesslyp.112Communication with printer lost when connected to Virtual Private Network (VPN)p.114Resolving intermittent wireless communications issuesp.115Noticesp.118Product informationp.118Edition noticep.118UNITED STATES GOVERNMENT RIGHTSp.119Trademarksp.119Licensing noticesp.119Federal Communications Commission (FCC) compliance information statementp.119Hinweis zum GS-Zeichenp.120Noise emission levelsp.120Temperature informationp.121Waste from Electrical and Electronic Equipment (WEEE) directivep.121Product disposalp.121Battery noticep.121ENERGY STARp.121Power consumptionp.122Product power consumptionp.122Power Saverp.122Off modep.122Total energy usagep.122European Community (EC) directives conformityp.123Regulatory notices for telecommunication terminal equipmentp.123Notice to users of the US telephone network: FCC requirementsp.123South Africa telecommunications noticep.124Notice to users of the Canadian telephone networkp.124Notice to users of the New Zealand telephone networkp.125Notice to Users in the European Unionp.126Regulatory notices for wireless productsp.127Exposure to radio frequency radiationp.127Notice to users in Brazilp.127Industry Canada (Canada)p.127Taiwan NCC RF notice statementp.128Notice to users in the European Unionp.128LEXMARK SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENTSp.130Indexp.135
Page 1 of the Lexmark 10E user manual — 101, 10E
Page 1 · click to enlarge
Page 1

S300 Series User's Guide

April 2009 www.lexmark.com

Machine type(s):

4443 Model(s):

101, 10E

Page 2 of the Lexmark 10E user manual — Table of Contents
Page 2 · Contents
Contents

Contents

Contentsp.2Safety informationp.5About your printerp.6Thank you for choosing this printer!p.6Minimizing your printer's environmental impactp.6Finding information about the printerp.7Understanding the parts of the printerp.9Ordering and replacing suppliesp.11Ordering ink cartridgesp.11Using genuine Lexmark ink cartridgesp.11Replacing ink cartridgesp.12Ordering paper and other suppliesp.13Recycling Lexmark productsp.13Using the printer control panel buttons and menusp.14Using the printer control panelp.14Changing temporary settings into new default settingsp.15Changing the Power Saver timeoutp.16Saving energy with Eco-Modep.17Resetting to factory settingsp.17Using the printer softwarep.19Minimum system requirementsp.19Using the Windows printer softwarep.19Using the Macintosh printer softwarep.21Finding and installing optional softwarep.22Updating the printer software (Windows only)p.23Reinstalling the printer softwarep.23Uninstalling the printer softwarep.23Installing the printer softwarep.24Loading paper and original documentsp.25Loading paperp.25Saving paper default settingsp.27Loading original documents on the scanner glassp.28Printingp.29Tips for printingp.29Printing basic documentsp.29Printing a documentp.29Collating printed copiesp.30Printing pages in reverse orderp.30Printing multiple pages on one sheetp.31Printing documents from a memory card or flash drive (Windows only)p.32Printing specialty documentsp.33Printing envelopesp.33Printing labelsp.33Printing on custom-size paperp.34Printing on both sides of the paper (duplexing) manuallyp.35Working with photosp.37Using a memory card or flash drive with the printerp.37Supported memory cards and file typesp.38Printing photos using the printer control panelp.38Printing photos from a memory device using the printer softwarep.39Printing photos from a PictBridge-enabled digital camerap.40Printing photos from a memory device using the proof sheetp.41Printing photos from a digital camera using DPOFp.42Printing from a Bluetooth-enabled devicep.42Setting up a connection between your printer and a Bluetooth-enabled devicep.42Setting the Bluetooth security levelp.43Printing from a Bluetooth-enabled devicep.44Managing print jobsp.45Setting your printer as the default printerp.45Changing the printing modep.45Pausing print jobsp.46Resuming print jobsp.47Canceling print jobsp.47Copyingp.49Tips for copyingp.49Making copiesp.49Copying photosp.49Enlarging or reducing imagesp.50Adjusting copy qualityp.50Making a copy lighter or darkerp.50Collating copies using the printer control panelp.51Repeating an image on one pagep.51Copying multiple pages on one sheetp.52Making a duplex copy manuallyp.52Canceling copy jobsp.53Scanningp.54Tips for scanningp.54Scanning to a local or network computerp.54Scanning to a flash drive or memory cardp.55Scanning photos into an editing applicationp.55Scanning documents into an editing applicationp.57Scanning directly to e-mail using the printer softwarep.57Scanning to a PDFp.58Scanning FAQp.59How can I improve the quality of a scan?p.59How do I scan in black and white?p.59Why am I being asked for a PIN?p.59What is an application list, and how do I update it?p.59Canceling scan jobsp.60Networkingp.61Installing the printer on a wireless networkp.61Wireless network compatibilityp.61Supported network security optionsp.61Printing a network setup pagep.62Information you will need to set up the printer on a wireless networkp.62Installing the printer on a wireless networkp.63Installing the printer on other computersp.63Interpreting the colors of the Wi-Fi indicator lightp.64Special wireless installation instructionsp.64Assigning a static IP addressp.65Changing wireless settings after installationp.65Advanced wireless setupp.66Creating an ad hoc wireless networkp.66Adding a printer to an existing ad hoc wireless networkp.69Configuring the printer wirelessly using WPS (Wi-Fi Protected Setup)p.69Switching between USB and wireless connections (Windows only)p.70Switching between USB and wireless connections (Macintosh only)p.70Sharing a printer in a Windows environmentp.71Sharing a printer in a Macintosh environmentp.72Networking FAQp.73What is Wi-Fi Protected Setup?p.73Where do I find my WEP key or WPA passphrase?p.73What is an SSID?p.73Where do I find my SSID?p.74What is a network?p.74How do I find out what type of security my network is using?p.74How are home networks configured?p.74Why do I need an installation cable?p.76How do I attach the installation cable?p.76How are infrastructure and ad hoc networks different?p.77Finding the signal strengthp.78How can I improve wireless signal strength?p.78How can I make sure my computer and printer are connected to the same wireless network?p.79Can I use my printer on a USB and a network connection at the same time?p.81What is a MAC address?p.81How do I find the MAC address?p.81What is an IP address?p.82What is TCP/IP?p.82How do I locate IP addresses?p.82How are IP addresses assigned?p.83What is a key index?p.83Maintaining the printerp.84Maintaining ink cartridgesp.84Checking ink levelsp.84Aligning the printheadp.84Cleaning the printhead nozzlesp.85Cleaning the exterior of the printerp.86Cleaning the scanner glassp.86Troubleshootingp.87Before you troubleshootp.87Using the Service Center to solve printer problemsp.87If Troubleshooting does not solve your problemp.87Setup troubleshootingp.87Incorrect language appears on the displayp.88Printhead errorsp.88Software did not installp.90Print job does not print or is missing pagesp.90Printer is printing blank pagesp.91Printer is busy or does not respondp.91Cannot delete documents from the print queuep.92Cannot print through USBp.92Jams and misfeeds troubleshootingp.93Paper jam in the printerp.93Paper jam in the paper supportp.93Paper or specialty media misfeedsp.93Print troubleshootingp.94Poor quality at the edges of the pagep.94Streaks or lines on printed imagep.95Print speed is slowp.95Computer slows down when printingp.96Copy and scan troubleshootingp.96Copier or scanner does not respondp.96Scanner unit does not closep.96Poor copy or scanned image qualityp.96Partial copies or scans of documents or photosp.97Scan was not successfulp.97Scanning takes too long or freezes the computerp.97Cannot scan to a computer over a networkp.97Memory card troubleshootingp.98Memory card troubleshooting checklistp.98Nothing happens when a memory card is insertedp.98Cannot print documents from a memory card or flash drivep.98Photos do not transfer from a memory card across a wireless networkp.99Wireless troubleshootingp.99Wireless troubleshooting checklistp.99Resetting the wireless settings to factory defaultsp.100Cannot print over wireless networkp.100The Continue button is unavailablep.104Cannot print and there is a firewall on the computerp.105Wi-Fi indicator light is not litp.105Wi-Fi indicator light is green but the printer does not print (Windows only)p.106Wi-Fi indicator light is still orangep.107Wi-Fi indicator light is blinking orange during installationp.108Wireless print server not installedp.112“Communication not available” message displays when printing wirelesslyp.112Communication with printer lost when connected to Virtual Private Network (VPN)p.114Resolving intermittent wireless communications issuesp.115Noticesp.118Product informationp.118Edition noticep.118UNITED STATES GOVERNMENT RIGHTSp.119Trademarksp.119Licensing noticesp.119Federal Communications Commission (FCC) compliance information statementp.119Hinweis zum GS-Zeichenp.120Noise emission levelsp.120Temperature informationp.121Waste from Electrical and Electronic Equipment (WEEE) directivep.121Product disposalp.121Battery noticep.121ENERGY STARp.121Power consumptionp.122Product power consumptionp.122Power Saverp.122Off modep.122Total energy usagep.122European Community (EC) directives conformityp.123Regulatory notices for telecommunication terminal equipmentp.123Notice to users of the US telephone network: FCC requirementsp.123South Africa telecommunications noticep.124Notice to users of the Canadian telephone networkp.124Notice to users of the New Zealand telephone networkp.125Notice to Users in the European Unionp.126Regulatory notices for wireless productsp.127Exposure to radio frequency radiationp.127Notice to users in Brazilp.127Industry Canada (Canada)p.127Taiwan NCC RF notice statementp.128Notice to users in the European Unionp.128LEXMARK SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENTSp.130Indexp.135
Page 5 of the Lexmark 10E user manual — Safety information
Page 5 · click to enlarge
Page 5

Safety information

Connect the power cord to an electrical outlet that is near the product and easily accessible.

Do not place or use this product near water or wet locations.

Use only the power supply and power cord provided with this product or the manufacturer's authorized replacements.

This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.

CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.

Refer service or repairs, other than those described in the user documentation, to a professional service person.

SAVE THESE INSTRUCTIONS.

Safety information

Page 6 of the Lexmark 10E user manual — Conserving ink
Page 6 · click to enlarge
Page 6

About your printer

Thank you for choosing this printer!

We've worked hard to make sure it will meet your needs.

To start using your new printer right away, use the setup materials that came with the printer, and then skim the User’s Guide to learn how to perform basic tasks. To get the most out of your printer, read the User’s Guide carefully, and make sure you check the latest updates on our Web site.

We're committed to delivering performance and value with our printers, and we want to make sure you're satisfied. If you do encounter any problems along the way, one of our knowledgeable support representatives will be delighted to help you get back on track fast. And if you find something we could do better, please let us know. After all, you are the reason we do what we do, and your suggestions help us do it better.

Minimizing your printer's environmental impact

We are committed to protecting the environment and are continually improving our printers to reduce their environmental impact. By selecting certain printer settings or tasks, you may be able to reduce your printer's environmental impact even further.

Conserving energy

  • Eco-Mode. This feature sets the screen brightness to low and sets the printer to change to Power Saver mode after the printer is left idle for 10 minutes. Eco-Mode is enabled by default in your printer.
  • Select the lowest Power Saver timeout. The Power Saver feature puts the printer in a minimum-power standby mode after the printer has been idle for a set amount of time (the Power Saver timeout).
  • Share your printer. Wireless/network printers allow you to share a single printer among multiple computers, thus conserving energy and other resources.

Conserving paper

  • Print more than one page image on one side of the paper. The “Pages per sheet” feature allows you to print multiple pages on one sheet. You can print up to 8 page images on one side of a sheet of paper.
  • Print on both sides of the paper. Duplexing lets you print on both sides of the paper manually or automatically (depending on your printer model).
  • Preview print jobs before printing. Use the preview features found in Toolbars, the Print or Print Preview dialog, or the printer display (depending on your printer model).
  • Scan and save. To avoid printing multiple copies, you can scan documents or photographs and save them to a computer program, application, or flash drive for presentation.
  • Use recycled paper.

Conserving ink

  • Use Quick Print or Draft Mode. These modes can be used to print documents using less ink than normal and are ideal for printing documents that are mostly text.
  • Use High Yield cartridges. Inks in High-Yield cartridges allow you to print more pages with fewer cartridges.

About your printer

Page 7 of the Lexmark 10E user manual — Publications
Page 7 · click to enlarge
Page 7
  • Clean the printhead. Before replacing and recycling your ink cartridges, try using the “Clean Printhead” and “Deep Clean Printhead” features. These features clean the printhead nozzles to improve the quality of your prints.

Recycling

  • Return ink cartridges for reuse or recycling through the Lexmark Cartridge Collection Program. To return an ink cartridge, go to <a href="http://www.lexmark.com/recycle" rel="nofollow noopener" target="_blank">www.lexmark.com/recycle</a> . Follow the instructions to request a postage-paid bag.
  • Recycle the product packaging.
  • Recycle your old printer instead of throwing it away.
  • Recycle paper from discarded print jobs.
  • Use recycled paper.

To read the Lexmark Environmental Sustainability Report, see www.lexmark.com/environment.

Finding information about the printer

Publications

What are you looking for?Find it here Initial setup instructions: • Connecting the printer • Installing the printer softwareSetup documentation The setup documentation came with the printer and is also available on the Lexmark Web site at www.lexmark.com/publications/. Additional setup and instructions for using the printer: • Selecting and storing paper and specialty media • Loading paper • Performing printing, copying, scanning, and faxing tasks, depending on your printer model • Configuring printer settings • Viewing and printing documents and photos • Setting up and using printer software • Setting up and configuring the printer on a network, depending on your printer model • Caring for and maintaining the printer • Troubleshooting and solving problemsUser's Guide The User's Guide is available on the installation software CD. For updates, check our Web site at www.lexmark.com/publications/.
Lexmark 10E — Publications diagram (page 7)
Fig. 1 · Publications
Lexmark 10E — Publications diagram (page 7)
Fig. 2 · Publications

About your printer

Page 8 of the Lexmark 10E user manual — Finding information about the printer
Page 8 · click to enlarge
Page 8
What are you looking for?Find it here Help using the printer softwareWindows or Mac Help Open a printer software program or application, and then click Help. Click to view context-sensitive information. Notes: • The Help installs automatically with the printer software. • The printer software is located in the printer Program folder or on the desktop, depending on your operating system. The latest supplemental information, updates, and online technical support: • Troubleshooting hints and tips • Frequently asked questions • Documentation • Driver downloads • Live chat support • E-mail supportLexmark Support Web site—support.lexmark.com Note: Select your region, and then select your product to view the appropriate support site. Record the following information (located on the store receipt and the back of the printer), and have it ready when you contact support so that they may serve you faster: • Machine Type number • Serial number • Date purchased • Store where purchased Telephone supportIn the US, call us at: 1-800-332-4120 Monday–Friday (8:00 AM–11:00 PM ET), Saturday (Noon–6:00 PM ET) Support telephone numbers and hours of operation for your region or country can be found on the Support Web site (support.lexmark.com) or on the printed warranty that came with your printer. Warranty informationWarranty information varies by country or region: • In the US—See the Statement of Limited Warranty included with this printer, or at support.lexmark.com. • Rest of the world—See the printed warranty that came with your printer.

About your printer

Page 9 of the Lexmark 10E user manual — Understanding the parts of the printer
Page 9 · click to enlarge
Page 9

Understanding the parts of the printer

Lexmark 10E — Understanding the parts of the printer diagram (page 9)
Fig. 3 · Understanding the parts of the printer
Use theTo 1Paper supportLoad paper. 2Paper guide adjustment leverAdjust the paper guides. 3Wi-Fi indicatorCheck wireless status. 4Card reader lightCheck card reader status. The light blinks to indicate that a memory card is being accessed. 5Memory card slotsInsert a memory card. 6PictBridge and USB portConnect a PictBridge-enabled digital camera, USB Bluetooth adapter or a flash drive to the printer. 7Paper exit trayHold paper as it exits. 8Printer control panelOperate the printer. 9Scanner lidAccess the scanner glass. 10Paper feed guardPrevent items from falling into the paper slot. 11Paper guidesKeep paper straight when feeding.

About your printer

Page 10 of the Lexmark 10E user manual — Understanding the parts of the printer
Page 10 · click to enlarge
Page 10
Lexmark 10E — Understanding the parts of the printer diagram (page 10)
Fig. 4 · Understanding the parts of the printer
Use theTo 1Scanner glassScan and copy photos and documents. 2Power supply with portConnect the printer to a power source. 3USB portConnect the printer to a computer using a USB cable. Warning—Potential Damage: Do not touch the USB port except when plugging in or removing a USB cable or installation cable. 4Printhead accessInstall the printhead. Note: The carrier moves to the printhead access area when no printhead is installed in the printer. 5Ink cartridge accessInstall, replace, or remove ink cartridges. 6Scanner unit• Access the ink cartridges and printhead. • Remove paper jams.

About your printer

Page 11 of the Lexmark 10E user manual — Using genuine Lexmark ink cartridges
Page 11 · click to enlarge
Page 11

Ordering and replacing supplies

Ordering ink cartridges

Page yields available at www.lexmark.com/pageyields. For best results, use only Lexmark ink cartridges.

Lexmark S300 Series models (except Lexmark S308)

ItemReturn Program Cartridge1Regular cartridge2 Black cartridge100100A High yield black cartridge100XL100XLA Yellow color cartridge100100A High yield yellow color cartridge100XL100XLA Cyan color cartridge100100A High yield cyan color cartridge100XL100XLA Magenta color cartridge100100A High yield magenta color cartridge100XL100XLA 1 Licensed for a single use only. After use, return this cartridge to Lexmark for remanufacturing, refilling, or recycling. 2 Available only on the Lexmark Web site at www.lexmark.com.
Lexmark 10E — Ordering and replacing supplies diagram (page 11)
Fig. 5 · Ordering and replacing supplies
ItemReturn Program Cartridge1Regular cartridge2 Black cartridge108108A High yield black cartridge108XL108XLA Yellow color cartridge108108A High yield yellow color cartridge108XL108XLA Cyan color cartridge108108A High yield cyan color cartridge108XL108XLA Magenta color cartridge108108A High yield magenta color cartridge108XL108XLA 1 Licensed for a single use only. After use, return this cartridge to Lexmark for remanufacturing, refilling, or recycling. 2 Available only on the Lexmark Web site at www.lexmark.com.
Lexmark 10E — Ordering and replacing supplies diagram (page 11)
Fig. 6 · Ordering and replacing supplies

Using genuine Lexmark ink cartridges

Lexmark printers, ink cartridges, and photo paper are designed to perform together for superior print quality, and our inks are formulated to work with your printer and help extend the life of your product. We recommend that you use only genuine Lexmark ink cartridges.

Ordering and replacing supplies

Lexmark S308 models

Page 12 of the Lexmark 10E user manual — Replacing ink cartridges
Page 12 · click to enlarge
Page 12

Lexmark's warranty does not cover damage caused by non-Lexmark ink or ink cartridges.

Replacing ink cartridges

Make sure you have a new ink cartridge or cartridges before you begin. You must install new cartridges immediately after removing the old ones or the ink remaining in the printhead nozzles may dry out.

1 Turn on your printer.

2 Open the printer.

Lexmark 10E — Replacing ink cartridges diagram (page 12)
Fig. 7 · Replacing ink cartridges

3 Press the release tab, and then remove the used ink cartridge or cartridges.

Lexmark 10E — Replacing ink cartridges diagram (page 12)
Fig. 8 · Replacing ink cartridges

4 Install each ink cartridge. Use two hands to install the black cartridge.

Lexmark 10E — Replacing ink cartridges diagram (page 12)
Fig. 9 · Replacing ink cartridges

5 Close the printer.

Ordering and replacing supplies

Page 13 of the Lexmark 10E user manual — Recycling Lexmark products
Page 13 · click to enlarge
Page 13

Ordering paper and other supplies

To order supplies or to locate a dealer near you, visit our Web site at www.lexmark.com.

For more information, go to www.lexmark.com.

  • Lexmark Photo Paper
  • Letter
  • A4
  • 4 x 6 in.
  • Lexmark PerfectFinish Photo Paper
  • Letter
  • A4
  • 4 x 6 in.
  • Availability may vary by country or region.
  • For best results when printing photos or other high-quality images, use Lexmark Photo Paper or Lexmark PerfectFinish TM Photo Paper.
  • For more information, go to <a href="http://www.lexmark.com" rel="nofollow noopener" target="_blank">www.lexmark.com</a>

Recycling Lexmark products

To return Lexmark products to Lexmark for recycling:

1 Visit our Web site at www.lexmark.com/recycle.

2 Find the product type you want to recycle, and then select your country from the list.

3 Follow the instructions on the computer screen.

Ordering and replacing supplies

Item Part Number · USB cable 1021294 · Paper Paper size

Page 14 of the Lexmark 10E user manual — Using the printer control panel
Page 14 · click to enlarge
Page 14
Lexmark 10E — Using the printer control panel buttons and menus diagram (page 14)
Fig. 10 · Using the printer control panel buttons and menus

Using the printer control panel

The following diagrams explain the sections of the printer control panel:

Lexmark 10E — Using the printer control panel diagram (page 14)
Fig. 11 · Using the printer control panel
Lexmark 10E — Using the printer control panel diagram (page 14)
Fig. 12 · Using the printer control panel
  • Turn the printer on and off.
  • Switch to Power Saver mode.

to switch to Power Saver mode. Press and hold

5 Color/Black Switch to color mode or black-and-white mode.

Start a print, scan, or copy job, depending on which mode is selected.

Using the printer control panel buttons and menus

Page 15 of the Lexmark 10E user manual — Changing temporary settings into new default settings
Page 15 · click to enlarge
Page 15
Use theTo
  • Cancel a print, copy, or scan job in progress.
  • Exit from a menu level of the Copy, Scan, Photo, or File Print menu to the top level of a menu.
  • Exit from a menu level of the Setup menu to the top level of the previous mode.
  • Clear current settings or error messages, and return to default settings.

View:

  • Printer status
  • Messages
  • Menus
  • Select menu options.
  • Save settings.
  • Feed or eject paper. Press and hold for 3 seconds to feed or eject paper from the printer.

10 Arrow buttons • Choose a menu or submenu item that appears on the display.

  • Return to the previous screen.
  • Exit from one menu level to a higher one.

Access the setup menu and change printer settings.

Changing temporary settings into new default settings

The following menus revert to default settings after two minutes of inactivity or after the printer is turned off:

  • Copy menu
  • Copies
  • Quality
  • Lighter/Darker
  • Resize
  • Original Size
  • Pages per Sheet
  • Copies per Sheet
  • Content Type
  • Scan menu
  • Quality
  • Original Size

Fax menu (selected models only)

  • Lighter/Darker
  • Quality

Using the printer control panel buttons and menus

Show 5 more labels / short text on this page
7 Cancel button · 8 Display · 9 Select button · 11 Back button · 12 Setup button
Page 16 of the Lexmark 10E user manual — Changing the Power Saver timeout
Page 16 · click to enlarge
Page 16

Photo menu The following Photo options will not time out after two minutes of inactivity or after you turn off the printer, but they will return to the factory default settings when a memory card or flash drive is removed.

  • Photo Effects
  • Photo Size
  • Layout
  • Quality

To change the temporary settings into new default settings

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Defaults, and then press

3 Press the arrow buttons to scroll to Set Defaults, and then press

Use Current appears on the display.

again to select Use Current.

until you exit Setup, or press another mode button.

To disable the settings timeout feature

You can disable the settings timeout feature if you do not want the printer to revert to the default settings after two minutes of inactivity or after the printer is turned off.

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Device Setup, and then press

3 Press the arrow buttons to scroll to Clear Settings Timeout, and then press

4 Press the arrow buttons to scroll to Never, and then press

until you exit Setup, or press another mode button.

Changing the Power Saver timeout

The Power Saver timeout is the time it takes for the printer to switch to Power Saver mode when the printer is left idle. The Power Saver feature optimizes energy efficiency by reducing the printer power consumption (as much as 28 percent on some printer models) compared to the default printer settings. To save the most energy, select the lowest Power Saver timeout.

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Device Setup, and then press

3 Press the arrow buttons to scroll to Power Saver, and then press

4 Press the arrow buttons to select a Power Saver timeout, and then press

until you exit Setup, or press another mode button.

Using the printer control panel buttons and menus

Show 4 more labels / short text on this page
4 Press · 5 Press · 5 Press · 5 Press
Page 17 of the Lexmark 10E user manual — Using the printer control panel menus
Page 17 · click to enlarge
Page 17

Saving energy with Eco-Mode

The Eco-Mode feature optimizes energy efficiency and saves money.

When Eco-Mode is enabled, the printer automatically switches to the following settings:

  • The printer display is dimmed.
  • The printer changes to Power Saver mode after ten minutes.
  • If you are using Eco-Mode, then the Eco-Mode settings override any changes you may make to individual settings that are part of Eco-Mode.
  • Eco-Mode is enabled by default.

To change the Eco-Mode setting:

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Device Setup, and then press

3 Press the arrow buttons to scroll to Eco-Mode.

4 Select the Eco-Mode setting, and then press

until you exit Setup, or press another mode button.

Resetting to factory settings

Resetting to factory default settings will delete all the printer settings you have previously selected.

Using the printer control panel menus

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Defaults, and then press

3 Press the arrow buttons to scroll to Set Defaults, and then press

4 Press the arrow buttons to scroll to Use Factory, and then press

5 When prompted to set the initial settings of your printer, make your selections using the printer control panel buttons.

Initial Setup Complete appears on the display.

Using the printer control panel buttons and menus

5 Press

Page 18 of the Lexmark 10E user manual — Using a button combination (if you cannot read the current language)
Page 18 · click to enlarge
Page 18

Using a button combination (if you cannot read the current language)

1 Turn off the printer.

for three seconds to turn off the printer.

2 From the printer control panel, press and hold

, and then press and release

to turn the printer on.

until Language appears on the display, indicating that the printer has been reset.

3 When prompted to set the initial settings of your printer, make your selections using the printer control panel buttons.

Initial Setup Complete appears on the display.

Using the printer control panel buttons and menus

and · and

Page 19 of the Lexmark 10E user manual — Software installed during printer installation
Page 19 · click to enlarge
Page 19

Using the printer software

Minimum system requirements

The printer software requires up to 500 MB of free disk space.

Supported operating systems

  • Microsoft Windows 7 (Web only) 1
  • Microsoft Windows Vista (SP1)
  • Microsoft Windows XP (SP3)
  • Microsoft Windows 2000 (SP4 or greater)
  • Macintosh PowerPC OS X v10.3.9 or later
  • Macintosh Intel OS X v10.4.4 or later
  • Linux Ubuntu 8.04 LTS and 8.10 (Web only) 1
  • Linux OpenSUSE 11.0 and 11.1 (Web only) 1
  • Linux Fedora 10 (Web only) 1

1 The printer driver for this operating system is available only at support.lexmark.com.

Using the Windows printer software

Software installed during printer installation

When you set up the printer using the installation software CD, all the necessary software was installed. You may have chosen to install some additional programs. The following table provides an overview of various software programs and what they can help you do.

If you did not install these additional programs during initial installation, then reinsert the installation software CD, run the installation software, and then select Install Additional Software from the Software Already Installed screen.

Using the printer software

Page 20 of the Lexmark 10E user manual — Printer software
Page 20 · click to enlarge
Page 20

Printer software

LexmarkTM Printer Home

  • Launch applications or programs.
  • Access the Fax Solutions software.
  • Scan or e-mail a photo or document.
  • Edit scanned documents.
  • Scan documents to PDF.
  • Adjust settings for the printer.
  • Order supplies.
  • Maintain ink cartridges.
  • Print a test page.
  • Register the printer.
  • Contact technical support.

(referred to as Printer Home)

Manage, edit, transfer, and print photos and documents.

(referred to as Fast Pics)

  • Print black or text-only Web pages to save ink.
  • Schedule automatic printing of Web pages.
  • Access Picnik and edit photos online.
  • Print, scan, or convert local files from Windows.

(referred to as Toolbar)

Lexmark Tools for Office

Access your favorite settings in Microsoft Office 2007.

(referred to as Tools for Office)

  • Send a fax.
  • Receive a fax in three-in-one printers.
  • Add, edit, or delete contacts in the built-in phone book.
  • Access the Lexmark Fax Setup Utility in four-in-one printers. Use the Fax Setup Utility to set the Speed Dial and Group Dial numbers, set Ringing and Answering, and print fax history and status reports.

(referred to as Fax Solutions)

Abbyy Sprint OCR Scan a document and produce text that you can edit with a word-processing program.

Lexmark Wireless Setup Utility

  • Set up the wireless printer on a wireless network.
  • Change the wireless settings of the printer.

(referred to as Wireless Setup Utility)

  • Troubleshoot the printer.
  • Access the printer maintenance functions.
  • Contact technical support.

(referred to as Service Center)

  • This program is installed automatically with the printer software.
  • You may be prompted to install this program from the Web, depending on your printer model.

Using the printer software

Show 5 more labels / short text on this page
Use the To · Lexmark Fast Pics · Lexmark Toolbar · Lexmark Fax Solutions · Lexmark Service Center
Page 21 of the Lexmark 10E user manual — Printer software
Page 21 · click to enlarge
Page 21

Printing Preferences When you select File Print with a document open and then click Properties, a Printing Preferences dialog appears. The dialog lets you select options for the print job, such as the following:

  • Select the number of copies to print.
  • Print two-sided copies.
  • Select the paper type.
  • Add a watermark.
  • Enhance images.
  • Save settings.

Using the Macintosh printer software

Software installed during printer installation

Software resident in the Macintosh OS

Print dialog Adjust the print settings and schedule print jobs.

Printer Services dialog (not available in Mac OS X v10.5 or later)

  • Access the printer utility.
  • Troubleshoot.
  • Order ink or supplies.
  • Contact Lexmark.
  • Check the printer software version installed on the computer.

Printer software

Applications are installed along with the printer software during installation. These applications are saved in the printer folder that appears on the Finder desktop after installation.

1 From the Finder desktop, double-click the printer folder.

2 Double-click the icon of the application that you want to use.

  • Scan photos and documents.
  • Customize settings for scan jobs.

(referred to as All-In-One Center)

Lexmark Fax Setup Utility (referred to as Fax Setup Utility)

  • Customize settings for fax jobs.
  • Create and edit the Speed Dial list.

Using the printer software

Show 4 more labels / short text on this page
Use the To · Use the To · Use the To · Lexmark All-In-One Center
Page 22 of the Lexmark 10E user manual — For Macintosh users
Page 22 · click to enlarge
Page 22

Lexmark Network Card Reader

  • View the contents of a memory device inserted into a network printer.
  • Transfer photos and PDF documents from a memory device to the computer over a network.

(referred to as Network Card Reader)

  • Get help with cartridge installation.
  • Print a test page.
  • Print an alignment page.
  • Clean the printhead nozzles.
  • Order ink or supplies.
  • Register the printer.
  • Contact technical support.

(referred to as Printer Utility)

Lexmark Wireless Setup Assistant

Set up the printer on a wireless network.

(referred to as Wireless Setup Assistant)

Finding and installing optional software

For Windows users

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.

3 Select Printer Home.

4 Choose your printer from the printer drop-down list.

5 From the Support tab, click On-line support.

6 From the Web site, select your printer and download the driver.

7 Install additional or optional software.

For Macintosh users

1 From the Finder desktop, double-click the printer folder.

2 Double-click the Printer Utility icon.

3 From the Web Links tab, click Customer Support.

4 From the Web site, select your printer and download the driver.

5 Install additional or optional software.

Using the printer software

Use the To · Lexmark Printer Utility · 1 Click

Page 23 of the Lexmark 10E user manual — For Macintosh users
Page 23 · click to enlarge
Page 23

Updating the printer software (Windows only)

Checking for software updates

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.

3 Select Printer Home.

4 Choose your printer from the printer drop-down list.

5 From the Support tab, select Check for updates.

6 Follow the instructions on the computer screen.

Enabling automatic software updates

1 With a document open, click File Print.

2 Click Properties, Preferences, Options, or Setup.

3 From the Advanced tab, click More Options.

4 In the Software Updates section, select Allow automatic updates from the web for my software.

5 Click OK.

Reinstalling the printer software

When you set up the printer using the installation software CD, all the necessary software was installed. If you encountered problems while installing, or if your printer does not appear in the Printers folder or as a printer option when you send a print job, then try removing and reinstalling the printer software.

Uninstalling the printer software

For Windows users

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.

3 Select the uninstall option.

4 Follow the instructions on the computer screen to remove the software.

5 Once the uninstall process in complete, restart your computer.

For Macintosh users

1 From the Finder desktop, double-click the printer folder.

2 Double-click the Uninstaller icon.

3 Follow the instructions on the computer screen to remove the software.

Using the printer software

1 Click · 1 Click

Page 24 of the Lexmark 10E user manual — Using the World Wide Web
Page 24 · click to enlarge
Page 24

Installing the printer software

For Windows users

1 Close all open software programs.

2 Insert the installation software CD.

If the Welcome screen does not appear after a minute, then launch the CD manually:

, or click Start and then click Run. b In the Start Search or Run box, type D:\setup.exe, where D is the letter of your CD or DVD drive.

3 Follow the instructions on the Welcome screen.

For Macintosh users

1 Close all open software applications.

2 Insert the installation software CD.

If the installation dialog does not appear after a minute, then click the CD icon on the desktop.

3 Double-click Install.

4 Follow the instructions on the installation dialog.

Using the World Wide Web

1 Go to the Lexmark Web site at www.lexmark.com.

2 From the Drivers & Downloads menu, click Driver Finder.

3 Select your printer, and then select your operating system.

4 Download the driver and install the printer software.

Using the printer software

a Click

Page 25 of the Lexmark 10E user manual — Paper and specialty media guidelines
Page 25 · click to enlarge
Page 25

Loading paper and original documents

Loading paper

1 Fan the paper.

Lexmark 10E — Loading paper and original documents diagram (page 25)
Fig. 13 · Loading paper and original documents

2 Center the paper on the paper support.

3 Adjust the paper guides so they rest against the edges of the paper.

Lexmark 10E — Loading paper and original documents diagram (page 25)
Fig. 14 · Loading paper and original documents

4 From the printer control panel, select or confirm your paper settings.

Paper and specialty media guidelines

Load up toMake sure that:

100 sheets of plain paper

  • The paper guides rest against the edges of the paper.
  • You load letterhead paper with the print side faceup and the top of the letterhead going into the printer first.
Lexmark 10E — Paper and specialty media guidelines diagram (page 25)
Fig. 15 · Paper and specialty media guidelines

Loading paper and original documents

Page 26 of the Lexmark 10E user manual — Loading paper and original documents
Page 26 · click to enlarge
Page 26
Load up toMake sure that:
  • 25 sheets of heavyweight matte paper
  • The print side of the paper is faceup.
  • The paper guides rest against the edges of the paper.
  • You select Automatic , Normal , or Photo print quality.

20 sheets of banner paper

  • You remove all paper from the paper support before inserting banner paper.
  • You use banner paper designed for inkjet printers.
  • You place a stack of banner paper on or behind the printer, and feed in the first sheet.
  • The paper guides rest against the edges of the paper.
  • You select A4 Banner or Letter Banner paper size.
Lexmark 10E — Loading paper and original documents diagram (page 26)
Fig. 16 · Loading paper and original documents
  • The print side of the envelope is faceup.
  • The paper guides rest against the edges of the envelopes.
  • You print the envelopes with Landscape orientation.
Lexmark 10E — Loading paper and original documents diagram (page 26)
Fig. 17 · Loading paper and original documents
Lexmark 10E — Loading paper and original documents diagram (page 26)
Fig. 18 · Loading paper and original documents
Lexmark 10E — Loading paper and original documents diagram (page 26)
Fig. 19 · Loading paper and original documents
  • You select the correct envelope size. Select the next biggest size if the exact envelope size is not listed, and set the left and right margins so your envelope is correctly positioned.
  • 25 sheets of labels
  • The print side of the label is faceup.
  • The paper guides rest against the edges of the paper.
  • You select Automatic , Normal , or Photo print quality.

Loading paper and original documents

10 envelopes

Page 27 of the Lexmark 10E user manual — Saving paper default settings
Page 27 · click to enlarge
Page 27
Load up toMake sure that:

25 greeting cards, index cards, postcards, or photo cards

  • The print side of the card is faceup.
  • The paper guides rest against the edges of the cards.
  • You select Automatic , Normal , or Photo print quality.
Lexmark 10E — Saving paper default settings diagram (page 27)
Fig. 20 · Saving paper default settings
  • 25 sheets of photo/glossy paper
  • The print side of the paper is faceup.
  • The paper guides rest against the edges of the paper.
  • You select Automatic , Normal , or Photo print quality.
  • 10 iron-on transfers
  • You follow the loading instructions on the iron-on transfer packaging.
  • The print side of the transfer is faceup.
  • The paper guides rest against the edges of the transfer.
  • You select Automatic , Normal , or Photo print quality.
  • 50 transparencies
  • The rough side of the transparencies is faceup.
  • The paper guides rest against the edges of the transparencies.

Saving paper default settings

You can set the default paper size, paper type, and photo print size for the documents and photos that you print.

1 From the printer control panel, press

2 Choose the default settings• If you want to set the default paper size: a Press

to select Paper Setup. b Press the arrow buttons to scroll to Paper Size, and then press

. c Press the arrow buttons to select the default paper size for the printer, and then press

. • If you want to set the default paper type: a Press

to select Paper Setup. b Press the arrow buttons to scroll to Paper Type, and then press

. c Press the arrow buttons to select the default paper type for the printer, and then press

Loading paper and original documents

Page 28 of the Lexmark 10E user manual — Loading original documents on the scanner glass
Page 28 · click to enlarge
Page 28
  • If you want to set the default photo print size: a Press the arrow buttons to scroll to Defaults , and then press

. b Press

to select Photo Print Size. c Press the arrow buttons to select the default photo print size for the printer, and then press

until you exit Setup, or press another mode button.

Loading original documents on the scanner glass

1 Open the scanner lid and place the document facedown on the scanner glass.

2 Close the scanner lid.

Lexmark 10E — Loading original documents on the scanner glass diagram (page 28)
Fig. 21 · Loading original documents on the scanner glass
Lexmark 10E — Loading original documents on the scanner glass diagram (page 28)
Fig. 22 · Loading original documents on the scanner glass

Loading paper and original documents

3 Press

Page 29 of the Lexmark 10E user manual — For Macintosh users
Page 29 · click to enlarge
Page 29

Printing

Tips for printing

  • Use the appropriate paper for your print job.
  • Select a higher print quality for better prints.
  • Make sure there is enough ink in the ink cartridges.
  • Remove each sheet as it is printed when printing photos or when working with specialty media.
  • Select the borderless setting when printing photos.

Printing basic documents

Printing a document

1 Load the paper in the printer.

2 Send the print job:

For Windows users

a With a document open, click File Print. b Click Properties, Preferences, Options, or Setup.

c Select the print quality, the number of copies to print, the type of paper to use, and how the pages should print. d Click OK to close any printer software dialogs. e Click OK or Print.

For Macintosh users

a With a document open, choose File > Print. b From the Printer pop-up menu, choose the printer.

c If necessary, click the disclosure triangle. d From the print options pop-up menu, choose the print quality, the number of copies to print, the type of

paper to use, and how the pages should print. e Click Print.

Printing

Page 30 of the Lexmark 10E user manual — For Windows users
Page 30 · click to enlarge
Page 30

Collating printed copies

If you print multiple copies of a document, then you can choose to print each copy as a set (collated) or to print the copies as groups of pages (not collated).

  • The collate option is available only when you are printing multiple copies.
  • To prevent smudging when printing photos, remove each photo as it exits the printer, and then let it dry before stacking.

For Windows users

1 With a document open, click File Print.

2 Click Properties, Preferences, Options, or Setup.

3 From the Copies section of the Print Setup tab, enter the number of copies that you want to print, and then select Collate Copies.

4 Click OK to close any printer software dialogs.

5 Click OK or Print.

For Macintosh users

1 With a document open, choose File > Print.

2 From the Printer pop-up menu, choose the printer.

3 If necessary click the disclosure triangle.

4 In the Copies field, enter the number of copies that you want to print, and then select Collated.

5 Click Print.

Printing pages in reverse order

By default, the first page is printed first. If you want to reverse the order in which pages print to make documents ready to read with the first page on top, then do the following:

For Windows users

1 With a document open, click File Print.

2 Click Properties, Preferences, Options, or Setup.

Collated Not collated · Printing

Page 31 of the Lexmark 10E user manual — For Macintosh users
Page 31 · click to enlarge
Page 31
  • 3 From the Copies section of the Print Setup tab, select a page order:
  • To print the last page first, select Print Last Page First .
  • To print the first page first, clear the Print Last Page First check box.

4 Click OK to close any printer software dialogs.

5 Click OK or Print.

For Macintosh users

1 With a document open, choose File > Print.

2 From the Printer pop-up menu, choose the printer.

3 If necessary, click the disclosure triangle.

4 From the print options pop-up menu, choose Paper Handling.

  • 5 From the Paper Handling menu, or from the Page Order pop-up menu, select a page order:
  • To print the last page first, select Reverse page order or Reverse .
  • To print the first page first, clear the Reverse page order or Reverse option.

6 Click Print.

Printing multiple pages on one sheet

For Windows users

1 With a document open, click File Print.

2 Click Properties, Preferences, Options, or Setup.

3 From the Layout list of the Advanced tab, select Pages per sheet.

4 Select the number of page images to print on each page.

If you want each page image to be surrounded by a border, then select Print Page Borders.

5 Click OK to close any printer software dialogs.

6 Click OK or Print.

For Macintosh users

1 With a document open, choose File > Print.

2 From the Printer pop-up menu, choose the printer.

3 If necessary, click the disclosure triangle.

4 From the print options pop-up menu, choose Copies & Pages, and then click Page Setup.

5 From the Paper Size pop-up menu, choose a paper size.

6 Choose an orientation, and then click OK.

Printing

Page 32 of the Lexmark 10E user manual — If the printer is using a Wireless connection (selected models only)
Page 32 · click to enlarge
Page 32
  • 7 From the print options pop-up menu, choose Layout .
  • From the Pages per Sheet pop-up menu, choose the number of page images that you want to print on one sheet.
  • From the Layout Direction menu, choose a layout direction.
  • If you want to print a border around each page image, then choose an option from the Border pop-up menu.

8 Click Print.

Printing documents from a memory card or flash drive (Windows only)

To enable the File Print function:

  • The printer must be connected to a computer through a USB cable or through a network.
  • The printer and the computer must be on.
  • The memory card or flash drive must contain document files that are supported by the printer. For more information, see “Supported memory cards and file types” on page 38.
  • The computer must contain applications that support the file types in the memory device.

1 Insert a memory card or flash drive.

When the printer detects the memory device, Memory Card Detected or Storage Device Detected appears on the display.

2 If only document files are stored on the memory device, then the printer automatically switches to File Print mode.

If document files and image files are stored on the memory device, then press

to select Documents.

3 Select and print the document:

If the printer is using a USB connection

a Press the arrow buttons to select the file name of the document that you want to print or the folder where

the document is saved in the memory device. b Press

, and then press

to start printing the document.

If the printer is using a Wireless connection (selected models only)

a Press the arrow buttons to select the file name of the document that you want to print. b Press

, and then wait for the printer to connect to the network computer or to finish searching the network for available computers. c When prompted, press the arrow buttons to select the name of the network computer, and then press

to start printing the document.

  • You may be prompted to enter a PIN if the computer requires it. Press the arrow buttons to enter the PIN. Press

each time you enter a number. • To assign a computer name and a PIN to the computer, see the Help for the printer software associated with your operating system.

Printing

Page 33 of the Lexmark 10E user manual — For Windows users
Page 33 · click to enlarge
Page 33

Printing specialty documents

Printing envelopes

1 Load the envelopes in the printer.

2 Send the print job:

For Windows users

a With a document open, click File Print. b Click Properties, Preferences, Options, or Setup.

c From the Paper Type list of the Print Setup tab, select Plain Paper. d From the Paper Size list, select the envelope size.

f Click OK to close any printer software dialogs. g Click OK or Print.

For Macintosh users

a With a document open, choose File > Print. b From the Printer pop-up menu, choose the printer.

c If necessary, click the disclosure triangle. d From the print options pop-up menu, choose Copies & Pages, and then click Page Setup. e From the Paper Size pop-up menu, choose the envelope size. If no size matches the size of the envelope, then

set a custom size. f Select an orientation, and then click OK. g Click Print.

  • Most envelopes use landscape orientation.
  • Make sure the same orientation is also selected in the software application.

Printing labels

1 Load the label sheets in the printer.

2 Send the print job:

For Windows users

a With a document open, click File Print. b Click Properties, Preferences, Options, or Setup.

Printing

Page 34 of the Lexmark 10E user manual — For Windows users
Page 34 · click to enlarge
Page 34

c From the Paper Size list of the Print Setup tab, choose a paper size that matches the size of the label sheet. If no paper size matches the label sheet size, then set a custom size. If necessary, choose the appropriate type of paper from the Paper Type list. d Click OK to close any printer software dialogs. e Click OK or Print.

For Macintosh users

a With a document open, choose File > Print. b From the Printer pop-up menu, choose the printer.

c If necessary, click the disclosure triangle. d From the print options pop-up menu, choose Copies & Pages, and then click Page Setup. e From the Paper Size pop-up menu, choose a size that matches the size of the label sheet. If no paper size

matches the label sheet size, then set a custom size. f Select an orientation, and then click OK. g From the print options pop-up menu, choose Quality & Media.

  • From the Paper Type pop-up menu, choose Card Stock .
  • From the Print Quality menu, choose a print quality other than Quick Print. h Click Print .

Tips on loading label sheets

  • Make sure the top of the label sheet feeds into the printer first.
  • Make sure the adhesive on the labels does not extend to within 1 mm of the edge of the label sheet.
  • Make sure the paper guide or paper guides rest against the edges of the label sheet.
  • Use full label sheets. Partial sheets (with areas exposed by missing labels) may cause labels to peel off during printing, resulting in a paper jam.

Printing on custom-size paper

Before beginning these instructions, load the custom-size paper in the printer.

For Windows users

1 With a document open, click File Print.

2 Click Properties, Preferences, Options, or Setup.

3 From the Paper Size list of the Print Setup tab, select Custom Size.

The Define Custom Paper Size dialog appears.

4 Set the paper size.

5 Select the measurement units to use (inches or millimeters).

6 Click OK to close any printer software dialogs.

7 Click OK or Print.

Printing

Page 35 of the Lexmark 10E user manual — For Windows users
Page 35 · click to enlarge
Page 35

For Macintosh users

1 With a document open, choose File > Print.

2 From the printer pop-up menu, choose the printer.

3 If necessary, click the disclosure triangle.

4 From the print options pop-up menu, choose Copies & Pages and then click Page Setup.

5 From the Settings pop-up menu, choose Custom Paper Size.

6 Create a custom size: a Select Use custom page size. b Type the Width and Height of the paper.

c Choose a Feed Method. d Click OK.

7 Click Print.

Printing on both sides of the paper (duplexing) manually

For Windows users

1 With a document open, click File Print.

2 Click Properties, Preferences, Options, or Setup.

3 Click the Advanced tab.

4 From the 2-Sided Printing section, select Manual.

5 Click OK. The printer prints the odd-numbered pages and the instruction sheet.

Printing

Page 36 of the Lexmark 10E user manual — For Macintosh users
Page 36 · click to enlarge
Page 36

6 Flip and reload the paper, following the directions on the instruction sheet to complete the print job.

Lexmark 10E — Printing on both sides of the paper (duplexing) manually diagram (page 36)
Fig. 23 · Printing on both sides of the paper (duplexing) manu…

For Macintosh users

1 With a document open, choose File > Print.

2 From the print options pop-up menu, choose Paper Handling.

3 From the Print or “Pages to print” pop-up menu, select to print the odd numbered pages.

4 After printing the first set of pages, flip and reload the paper.

5 Repeat steps 1 and 2.

6 From the Print or “Pages to print” pop-up menu, select to print the even numbered pages.

7 Click Print.

Printing

Page 37 of the Lexmark 10E user manual — Using a memory card or flash drive with the printer
Page 37 · click to enlarge
Page 37

Working with photos

Using a memory card or flash drive with the printer

Memory cards and flash drives are storage devices frequently used with cameras and computers. You can remove the memory card from the camera or the flash drive from the computer and insert it directly into the printer.

1 Insert a memory card into the card slot or a flash drive into the USB port.

Inserting a memory card Inserting a flash drive

Lexmark 10E — Using a memory card or flash drive with the printer diagram (page 37)
Fig. 24 · Using a memory card or flash drive with the printer
Lexmark 10E — Using a memory card or flash drive with the printer diagram (page 37)
Fig. 25 · Using a memory card or flash drive with the printer
  • Insert the card with the brand name label facing right.
  • Make sure any arrows on the card point toward the printer.
  • If necessary, connect the memory card to the adapter that came with it.
  • Make sure that the memory card inserted is supported by the printer. For more information, see “Supported memory cards and file types” on page 38.
  • The flash drive uses the same port that is used for a PictBridge camera cable.
  • An adapter may be necessary if your flash drive does not fit directly into the port.
Lexmark 10E — Using a memory card or flash drive with the printer diagram (page 37)
Fig. 26 · Using a memory card or flash drive with the printer

2 Look for Memory Card Detected or Storage Device Detected on the display.

  • If the printer does not recognize the memory device, then remove and reinsert it.
  • If a flash drive or a digital camera set to mass storage mode is inserted into the USB port while a memory card is in the card slot, then a message appears on the display prompting you to choose which memory device to use.

Printing

Page 38 of the Lexmark 10E user manual — Printing photos using the printer control panel
Page 38 · click to enlarge
Page 38

Supported memory cards and file types

Memory Card File Type

  • Secure Digital (SD)
  • Micro Secure Digital (with adapter) (Micro SD)
  • Mini Secure Digital (with adapter) (Mini SD)
  • MultiMedia Card (MMC)
  • Reduced Size MultiMedia Card (with adapter) (RS-MMC)
  • MultiMedia Card mobile (with adapter) (MMCmobile)
  • Memory Stick
  • Memory Stick PRO
  • Memory Stick Duo (with adapter)
  • Memory Stick PRO Duo (with adapter)
  • xD-Picture Card
  • xD-Picture Card (Type H)
  • xD-Picture Card (Type M)
  • Secure Digital High Capacity (SDHC)

Documents:

  • .doc (Microsoft Word)
  • .xls (Microsoft Excel)
  • .ppt (Microsoft PowerPoint)
  • .pdf (Adobe Portable Document Format)
  • .rtf (Rich Text Format)
  • .docx (Microsoft Word Open Document Format)
  • .xlsx (Microsoft Excel Open Document Format)
  • .pptx (Microsoft PowerPoint Open Document Format)
  • .wpd (WordPerfect)

Images:

  • JPEG
  • TIFF

Printing photos using the printer control panel

1 Load photo paper.

2 From the printer control panel, press

3 Insert a memory card, flash drive, or digital camera set to mass storage mode.

If document files and image files are stored in the memory device, then press the arrow buttons to select Photos, and then press

4 Press the arrow buttons to scroll to Easy Photo or Print Photos, and then press

  • Select Easy Photo if you want to print photos quickly.
  • Select Print Photos if you want to customize the photos before printing them.

5 Press the arrow buttons to select a photo printing option, and then press

Note: You can choose to print the most recent photo, print all the photos, print photos that fall within a date range, print photos by selecting the photo numbers on a proof sheet, or print pre-selected photos from a digital camera using Digital Print Order Format (DPOF). The DPOF option appears only when there is a valid DPOF file in your memory device.

6 Adjust the print settings: • If you are in the Easy Photo menu, then press the arrow buttons to select the paper size and photo size. Press

each time you make a selection. • If you are in the Print Photos menu, then press the arrow buttons to select the photo size, paper size, paper type, layout, photo effects, and quality of the photos, and to adjust the brightness and color effects of the photos. Press

each time you make a selection.

Printing

Page 39 of the Lexmark 10E user manual — If the printer is using a Wireless connection (selected models only)
Page 39 · click to enlarge
Page 39

7 Press the Color/Black button to set a color or black-and-white print.

When you select color or black-only printing, the light near your choice comes on.

Printing photos from a memory device using the printer software

1 Load photo paper with the glossy or printable side faceup. (If you are not sure which side is the printable side, then see the instructions that came with the paper.)

2 From the printer control panel, press

3 Insert a memory card, flash drive, or digital camera set to mass storage mode.

If document files and image files are stored on the memory device, then press

to select Photos.

4 Transfer or print the photos:

If the printer is using a USB connection

  • For Windows users Fast Pics launches automatically when you insert the memory device. Follow the instructions on the computer screen to transfer the photos to the computer or to print.
  • For Macintosh users If you have set an application to launch when a memory device is connected to the computer, then the application automatically launches. Follow the instructions on the computer screen to transfer the photos to the computer or to print.

If the printer is using a Wireless connection (selected models only)

a Press the arrow buttons to scroll to Select Computer, and then press

b Press the arrow buttons to select the network computer where you want to save the photos, and then press

. c Transfer or print the photos:

  • For Windows users Fast Pics launches automatically when you insert the memory device. Follow the instructions on the computer screen to transfer the photos to the computer or to print.
  • For Macintosh users Select Yes to view images from the memory device. The Network Card Reader launches on the computer. Follow the instructions on the computer screen to transfer the photos to the computer or to print.

8 Press · Printing

Page 40 of the Lexmark 10E user manual — Printing photos from a PictBridge-enabled digital camera
Page 40 · click to enlarge
Page 40

Printing photos from a PictBridge-enabled digital camera

PictBridge is a technology available in most digital cameras that lets you print directly from your digital camera without using a computer.

1 Insert one end of the USB cable into the camera.

2 Insert the other end of the cable into the PictBridge port on the front of the printer.

Lexmark 10E — Printing photos from a PictBridge-enabled digital camera diagram (page 40)
Fig. 27 · Printing photos from a PictBridge-enabled digital ca…
  • Make sure that the PictBridge-enabled digital camera is set to the correct USB mode. If the camera USB selection is incorrect, then the camera is detected as a flash drive, or an error message will be displayed on the printer control panel. For more information, see the camera documentation.
  • The printer reads only one memory device at a time.

3 If the PictBridge connection is successful, then the following message appears on the display: PictBridge Camera detected. Press OK to change settings.

to access the PictBridge menu.

5 Press the arrow buttons to select the paper size, paper type, photo size, and layout of the photos that you want to print. Press

each time you make a selection.

6 See the documentation for your camera to begin printing.

4 Press · Printing

Page 41 of the Lexmark 10E user manual — Printing photos from a memory device using the proof sheet
Page 41 · click to enlarge
Page 41

Printing photos from a memory device using the proof sheet

1 Load letter- or A4-size plain paper.

2 From the printer control panel, press

3 Insert a memory card or flash drive.

If document files and image files are stored in the memory device, then press the arrow buttons to select Photos, and then press

4 Press the arrow buttons to scroll to Proof Sheet, and then press

5 Press the arrow buttons to select an option to print a proof sheet.

You can print a proof sheet:

  • For all photos on the memory device.
  • For the 20 most recent photos, if there are 20 or more photos on the memory device.
  • By date, if the photos on the card were taken on different dates. If you choose this option, then select the date.

The proof sheet prints.

7 Follow the instructions on the proof sheet to select which photos to print, the number of copies per photo, red-eye reduction, page layout, print options, and paper size.

8 When Scan Proof Sheet appears on the display, press

, and then load the proof sheet facedown on the scanner glass.

The printer scans the proof sheet.

10 Load photo paper with the glossy or printable side faceup. (If you are not sure which side is the printable side, then see the instructions that came with the paper.)

11 Press the Color/Black button to set a color or black-and-white print.

When you select color or black-only printing, the light near your choice comes on.

to print the photos.

Show 4 more labels / short text on this page
6 Press · 9 Press · 12 Press · Printing
Page 42 of the Lexmark 10E user manual — Setting up a connection between your printer and a Bluetooth-enabled device
Page 42 · click to enlarge
Page 42

Printing photos from a digital camera using DPOF

If your camera supports Digital Print Order Format (DPOF), then you can specify which photos to print, how many of each, and the print settings while the memory card is still in the camera. The printer recognizes these settings when you insert the memory card into the printer or connect the camera to the printer.

1 Load photo paper with the glossy or printable side faceup. (If you are not sure which side is the printable side, then see the instructions that came with the paper.)

2 From the printer control panel, press

3 Insert a memory card.

Memory Card Detected appears on the display.

4 Press the arrow buttons to scroll to Print Photos, and then press

5 Press the arrow buttons to scroll to Print DPOF, and then press

to print the photos.

Printing from a Bluetooth-enabled device

  • This printer is compliant with Bluetooth Specification 2.0. It supports the following profiles: Object Push Profile (OPP) and Serial Port Profile (SPP). Check with your Bluetooth-enabled device manufacturers (cellular phone or PDA) to determine their hardware compatibility and interoperability. It is recommended that you use the latest firmware on your Bluetooth-enabled device.
  • To print Microsoft documents from your Windows Mobile/Pocket PC PDA, additional third-party software and drivers are required. For more information about the required software, see the documentation for your PDA.

Setting up a connection between your printer and a Bluetooth-enabled device

You need to set up a connection between a Bluetooth-enabled device and your printer if you are sending a print job from the Bluetooth device for the first time. You will need to repeat the setup if:

  • You reset the printer to its factory default settings.
  • You change the Bluetooth security level or the Bluetooth pass key.
  • The Bluetooth-enabled device you are using requires users to set up a Bluetooth connection on every print job. For more information, see the documentation for your Bluetooth device.
  • The name of the Bluetooth device you are using is automatically deleted from the Bluetooth device list.

When the Bluetooth security level is set to High, the printer saves a list of up to eight Bluetooth devices that have previously set up a connection with the printer. When the printer detects more than eight devices, the least recently used device is removed from the list. You need to repeat the setup of the deleted device to be able to send a print job to the printer.

Printing

Page 43 of the Lexmark 10E user manual — Setting the Bluetooth security level
Page 43 · click to enlarge
Page 43

To set up a connection between the printer and a Bluetooth-enabled device:

1 Insert a USB Bluetooth adapter into the USB port located on the front of the printer.

Lexmark 10E — Setting the Bluetooth security level diagram (page 43)
Fig. 28 · Setting the Bluetooth security level

Bluetooth Dongle Connected appears on the display.

2 From the printer control panel, press

3 Press the arrow buttons to scroll to Bluetooth Setup, and then press

4 Press the arrow buttons to scroll to Discovery, and then press

5 Make sure Discovery is set to On. If necessary, press the arrow buttons to scroll to On, and then press

The printer is now ready to accept a connection from a Bluetooth-enabled device.

6 Configure the Bluetooth-enabled device to set up a connection to the printer. For more information, see the documentation for your Bluetooth device.

Setting the Bluetooth security level

1 Insert a Bluetooth USB adapter into the USB port.

Bluetooth Dongle Connected appears on the display.

Printing

Page 44 of the Lexmark 10E user manual — Printing from a Bluetooth-enabled device
Page 44 · click to enlarge
Page 44

2 From the printer control panel, press

3 Press the arrow buttons to scroll to Bluetooth Setup, and then press button

4 Press the arrow buttons to scroll to Security Level, and then press

5 Press the arrow buttons to select the security level, and then press

  • Select Low to allow Bluetooth devices to connect and send print jobs to your printer without requiring users to enter a pass key.
  • Select High to require users to enter a four-digit numeric pass key on the Bluetooth device before connecting and sending print jobs to the printer.

6 The Bluetooth Pass Key menu appears on the display if you set the security level to High. Press the arrow buttons to enter the four-digit pass key. Press

each time you enter a number.

Printing from a Bluetooth-enabled device

1 Insert a USB Bluetooth adapter into the USB port.

Bluetooth Dongle Connected appears on the display.

  • A Bluetooth adapter is not included with the printer.
  • Your printer automatically switches to Bluetooth mode when you insert a USB Bluetooth adapter.

2 Make sure the printer is set up to receive Bluetooth connections. For more information, see “Setting up a connection between your printer and a Bluetooth-enabled device” on page 42.

3 Set up the Bluetooth device to print to the printer. For more information, see the documentation for your Bluetooth device.

4 See the documentation for your Bluetooth device to begin printing.

Printing

Page 45 of the Lexmark 10E user manual — For Macintosh users
Page 45 · click to enlarge
Page 45

Managing print jobs

Setting your printer as the default printer

Your printer should be selected automatically from the Print dialog when you send a print job. If you have to manually select your printer, then it is not the default printer.

To set the default printer:

For Windows users

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.

3 Press Enter, or click OK.

The printer folder opens.

4 Right-click the printer, and then select Set as Default Printer.

For Macintosh users

1 From the Apple menu, choose System Preferences.

2 Click Print & Fax.

3 Select the printer from the Default Printer pop-up menu, or select the printer and click Make Default, depending on your operating system.

Changing the printing mode

To conserve ink, you can change the default printing mode for all print jobs to Quick Print. It uses less ink and is ideal for printing text-only documents. If you need to change to a different print mode to print photos or other high-quality documents, then you can select a different mode from the Print dialog before sending the print job.

To change the default print mode:

For Windows users

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.

3 Press Enter, or click OK.

The printer folder opens.

4 Right-click the printer, and then select Printing Preferences.

5 Select Quick Print as the printing mode.

For Macintosh users

1 With a document open, choose File > Print.

2 From the printer pop-up menu, choose the printer.

1 Click · 1 Click · Printing

Page 46 of the Lexmark 10E user manual — For Macintosh users
Page 46 · click to enlarge
Page 46

3 From the print options pop-up menu, choose Print Settings or Quality & Media, depending on your operating system.

4 From the Print Quality pop-up menu, choose Quick Print as the printing mode.

5 From the Presets pop-up menu, choose Save as, and then type a name for your setting configuration.

You must choose this configuration name from the Presets pop-up menu for each print job.

Changing the printing mode for a single print job

For Windows users

1 With a document open, click File Print.

2 Click Properties, Preferences, Options, or Setup.

3 Select Automatic, Quick Print, Normal, or Best.

For Macintosh users

1 With a document open, choose File > Print.

2 From the printer pop-up menu, choose the printer.

3 From the print options pop-up menu, choose Print Settings or Quality & Media, depending on your operating system.

4 From the Print Quality pop-up menu, choose Automatic, Quick Print, Normal, or Best.

Pausing print jobs

For Windows users

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.

3 Press Enter, or click OK.

The printer folder opens.

4 Right-click the printer, and then select Pause Printing.

For Macintosh users

1 Click the printer icon on the Dock.

The print queue dialog appears.

  • 2 Pause the print job:
  • If you want to pause a particular print job, then choose the document name, and then click Hold .
  • If you want to pause all print jobs in the queue, then click Pause Printer or Stop Jobs , depending on your operating system.

1 Click · Printing

Page 47 of the Lexmark 10E user manual — For Windows users
Page 47 · click to enlarge
Page 47

Resuming print jobs

For Windows users

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.

3 Press Enter, or click OK.

The printer folder opens.

4 Right-click the printer, and then select Open.

  • 5 Resume the print job:
  • If you want to resume a particular print job, then right-click the document name, and then select Resume or Restart .
  • If you want to resume all print jobs in the queue, then click Printer , and then clear the selection for Pause Printing.

For Macintosh users

1 From the Apple menu, choose System Preferences.

2 Click Print & Fax.

3 From the Printers list or pop-up menu, choose the printer.

4 Click Open Print Queue or Set Up Printers depending on your operating system.

The print queue dialog appears.

  • 5 Resume the print job:
  • If you want to resume a particular print job, then choose the document name, and then click Resume .
  • If you want to resume all print jobs in the queue, then click Resume Printer or Start Jobs .

Canceling print jobs

To cancel a print job from the printer control panel, press

. To cancel a print job from the computer, do the following:

For Windows users

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.

3 Press Enter, or click OK.

The printer folder opens.

4 Right-click the printer, and then select Open.

  • 5 Cancel the print job:
  • If you want to cancel a particular print job, then right-click the document name, and then select Cancel .
  • If you want to cancel all print jobs in the queue, then click Printer Cancel All Documents .

1 Click · 1 Click · Printing

Page 48 of the Lexmark 10E user manual — For Macintosh users
Page 48 · click to enlarge
Page 48

For Macintosh users

1 Click the printer icon on the Dock.

2 From the print queue dialog, choose the job you want to cancel, and then click Delete.

Printing

Page 49 of the Lexmark 10E user manual — Copying photos
Page 49 · click to enlarge
Page 49

Copying

Automatic Document Feeder (ADF) Scanner glass

Use the ADF for multiple-page documents.

Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).

Tips for copying

  • When using the ADF, adjust the paper guide on the ADF to the width of the original document.
  • When using the scanner glass, close the scanner lid to avoid dark edges on the scanned image.
  • Do not load postcards, photos, small items, transparencies, photo paper, or thin media (such as magazine clippings) into the ADF. Place these items on the scanner glass.

Making copies

1 Load paper.

2 Load an original document faceup into the ADF or facedown on the scanner glass.

3 From the printer control panel, press

4 Press the arrow buttons to select the number of copies, and then press the Color/Black button to set a color or black-and-white copy.

When you select color or black-only printing, the light near your choice comes on.

Copying photos

1 Load photo paper.

2 Place a photo facedown on the scanner glass.

3 From the printer control panel, press

5 Press · Copying

Page 50 of the Lexmark 10E user manual — Making a copy lighter or darker
Page 50 · click to enlarge
Page 50

until Photo Reprint appears.

5 Press the arrow buttons to scroll to Yes, and then press

6 Press the arrow buttons to select the desired photo size, and then press

Enlarging or reducing images

1 Load paper.

2 Load an original document facedown on the scanner glass.

3 From the printer control panel, press

until Resize appears.

5 Press the arrow buttons until the setting that you want appears.

  • If you select Custom %, then press

, and then press the arrow buttons to select the desired custom percent value. Press

to save the setting. • If you select Borderless, then the printer will reduce or enlarge the document or photo as necessary to print a borderless copy on the paper size that you selected. For best results with this resize setting, use photo paper and set the paper type to Photo, or let the printer automatically detect the paper type.

to reset the settings to the default. The resize setting also switches to 100% after two minutes of printer inactivity.

Adjusting copy quality

1 Load paper.

2 Load an original document faceup into the ADF or facedown on the scanner glass.

3 From the printer control panel, press

until Quality appears.

5 Press the arrow buttons to set the copy quality to Automatic, Draft, Normal, or Photo.

Making a copy lighter or darker

1 Load paper.

2 Load an original document faceup into the ADF or facedown on the scanner glass.

3 From the printer control panel, press

Show 7 more labels / short text on this page
4 Press · 7 Press · 4 Press · 6 Press · 4 Press · 6 Press · Copying
Page 51 of the Lexmark 10E user manual — Repeating an image on one page
Page 51 · click to enlarge
Page 51

until Lighter/Darker appears.

5 Press the arrow buttons to adjust the slider.

Collating copies using the printer control panel

If you print multiple copies of a document, then you can choose to print each copy as a set (collated) or to print the copies as groups of pages (not collated).

1 Load paper.

2 Load an original document faceup into the ADF or facedown on the scanner glass.

3 From the printer control panel, press

4 Press the arrow buttons to select the number of copies, and then press

until Collate appears.

6 Press the arrow buttons to scroll to On.

Repeating an image on one page

You can print the same page image multiple times on one sheet of paper. This option is helpful when creating items such as labels, decals, flyers, and handouts.

1 Load paper.

2 Load an original document faceup into the ADF or facedown on the scanner glass.

3 From the printer control panel, press

until Copies per Sheet appears.

5 Press the arrow buttons to select the number of times that an image is repeated on a page: once, four times, nine times, or 16 times.

Show 8 more labels / short text on this page
4 Press · 6 Press · Collated Not collated · 5 Press · 7 Press · 4 Press · 6 Press · Copying
Page 52 of the Lexmark 10E user manual — Making a duplex copy manually
Page 52 · click to enlarge
Page 52

Copying multiple pages on one sheet

The Pages per Sheet setting lets you copy multiple pages on one sheet by printing smaller images of each page. For example, you can condense a 20-page document into five pages if you use this setting to print four page images per sheet.

1 Load paper.

2 Load an original document faceup into the ADF or facedown on the scanner glass.

3 From the printer control panel, press

until Pages per Sheet appears.

5 Press the arrow buttons to select the number of pages that you want to copy on a sheet of paper. You may choose to copy one, two, or four page images on a sheet.

Making a duplex copy manually

1 Load paper.

2 Load an original document faceup into the ADF or facedown on the scanner glass.

3 From the printer control panel, press

4 Press the arrow buttons to select the number of copies, and then press the Color/Black button to set a color or black-and-white copy.

When you select color or black-only printing, the light near your choice comes on.

to print on one side of the paper.

  • 6 Load the next page of the document.
  • If you are copying a one-sided document, then load the next page faceup into the ADF or facedown on the scanner glass.
  • If you are copying a two-sided document, then flip the original document, and then reload it faceup into the ADF or facedown on the scanner glass.
Show 4 more labels / short text on this page
4 Press · 6 Press · 5 Press · Copying
Page 53 of the Lexmark 10E user manual — Canceling copy jobs
Page 53 · click to enlarge
Page 53

7 Remove the paper from the paper exit tray, and then reload the paper to print the other side of the document.

Canceling copy jobs

To cancel a copy job, press

Scanning stops and the printer returns to the previous menu.

8 Press · Copying

Page 54 of the Lexmark 10E user manual — Scanning to a local or network computer
Page 54 · click to enlarge
Page 54

Scanning

Automatic Document Feeder (ADF) Scanner glass

Use the ADF for multiple-page documents.

Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).

Tips for scanning

  • When using the ADF, adjust the ADF paper guide to the width of the original document.
  • When using the scanner glass, close the scanner lid to avoid dark edges on the scanned image.
  • Do not load postcards, photos, small items, transparencies, photo paper, or thin media (such as magazine clippings) into the ADF. Place these items on the scanner glass.
  • Select the PDF file type if you want to scan multiple pages and save them as one file.

Scanning to a local or network computer

1 Load an original document faceup into the ADF or facedown on the scanner glass.

2 From the printer control panel, press

3 Press the arrow buttons to scroll to Computer or Network, and then press

4 Press the arrow buttons to select the name of a local or network computer, and then press

The local or network computer is the destination that will receive the scan.

  • If the printer is connected only to a local computer, then the printer will automatically download a list of the scan applications.
  • You may be prompted to enter a PIN if the computer requires it. Press the arrow buttons to enter the PIN. Press

each time you enter a number. • To assign a computer name and a PIN to the computer, see the Help for the printer software associated with your operating system.

Scanning

Page 55 of the Lexmark 10E user manual — Using the printer control panel
Page 55 · click to enlarge
Page 55

5 Wait until the printer has finished downloading a list of the scan applications available on the selected computer.

6 Press the arrow buttons to select an application, and then press

7 Press the arrow buttons to select the resolution quality and the original image size. Press

each time you make a selection.

to start scanning.

The scan is complete when the application you selected in step 6 opens on the destination computer, and the scan appears within the application as a new file.

Scanning to a flash drive or memory card

Before you begin, make sure your flash drive or memory card is not write protected.

1 Load an original document faceup into the ADF or facedown on the scanner glass.

2 From the printer control panel, press

3 When Scan to appears on the display, insert the flash drive or memory card.

4 Press the arrow buttons to scroll to USB Flash Drive or Memory Card, and then press

5 Press the arrow buttons to select the resolution quality, the type of output you want to create, and the original image size. Press

each time you make a selection.

to start scanning.

The scan is complete when a message appears on the printer control panel indicating that the file you scanned has been saved.

Scanning photos into an editing application

Using the printer control panel

1 Load the photo or photos facedown on the scanner glass.

2 From the printer control panel, press

3 Press the arrow buttons to scroll to Computer or Network, and then press

4 Press the arrow buttons to select the name of a local or network computer, and then press

The local or network computer is the destination that will receive the scan.

  • If the printer is connected only to a local computer, then the printer will automatically download a list of the scan applications.
  • You may be prompted to enter a PIN if the computer requires it. Press the arrow buttons to enter the PIN. Press

each time you enter a number. • To assign a computer name and a PIN to the computer, see the Help for the printer software associated with your operating system.

8 Press · 6 Press · Scanning

Page 56 of the Lexmark 10E user manual — For Macintosh users
Page 56 · click to enlarge
Page 56

5 Wait until the printer has finished downloading the list of scan applications available on the selected computer.

6 Press the arrow buttons to select a photo editing application, and then press

7 Press the arrow buttons to select the resolution quality, the type of output you want to create, and the original image size. Press

each time you make a selection.

The scan is complete when the photo editing application you selected in step 6 opens on the destination computer, and the scan appears within the application as a new file.

Using the printer software

For Windows users

1 Load a photo or photos facedown on the scanner glass.

or Start.

3 Click All Programs or Programs, and then select the printer program folder from the list.

4 Select Printer Home.

5 Choose your printer from the printer drop-down list.

  • 6 Click Photo .
  • If you want to scan a single photo, or multiple photos as a single image, then select Single photo .
  • If you want to scan multiple photos at once and save them as separate images, then select Split into individual photos .

Scanning starts and the scan progress dialog appears.

7 Save the photo or photos and open in a photo editing application to edit.

For Macintosh users

1 Load a photo or photos facedown on the scanner glass.

2 From the Finder desktop, double-click the printer program folder.

3 Double-click the printer Center to open the All-In-One Center.

4 From the “What is being scanned?” menu on the main screen, select Photo.

5 From the “How will the scanned image be used?” pop-up menu, choose To be printed or To be viewed on monitor/Web page.

6 From the “Send scanned image to” menu, choose a destination folder or application for the scanned image.

7 If you have several images to scan, then select Prompt for multiple pages.

8 Click Preview/Edit.

The Scan dialog appears.

9 Adjust the image and scan settings as needed.

10 Click Scan.

8 Press · 2 Click · Scanning

Page 57 of the Lexmark 10E user manual — For Windows users
Page 57 · click to enlarge
Page 57

Scanning documents into an editing application

An Optical Character Recognition (OCR) application allows you to edit an original text document that has been scanned. In order for this to work, you must have an OCR application stored on a local or network computer and you must be able to choose it from the list of applications when you set up the scan.

When selecting settings for the scan:

  • Select to scan to the local computer or network computer where the OCR is installed.
  • Select to scan to the highest resolution.

For Windows users

1 Load an original document faceup into the ADF or facedown on the scanner glass.

or Start.

3 Click All Programs or Programs, and then select the printer program folder from the list.

4 Select Printer Home.

5 Choose your printer from the printer drop-down list.

6 Click Document.

Scanning starts and the scan progress dialog appears.

7 When the scan is finished, save the document in a word-processing application.

8 Open the document in the selected application to edit it.

For Macintosh users

1 Load an original document faceup into the ADF or facedown on the scanner glass.

2 From the Finder desktop, double-click the printer program folder.

3 Double-click the printer Center to open the All-In-One Center.

4 From the “What is being scanned?” menu on the main screen, select a document type other than Photo.

5 From the “How will the scanned image be used?” pop-up menu, choose To be edited (OCR).

6 From the “Send scanned image to” menu, choose a word-processing application to use for editing.

7 Click Scan.

8 Open the scanned document from a word-processing application to edit it.

Scanning directly to e-mail using the printer software

For Windows users

1 Load an original document faceup into the ADF or facedown on the scanner glass.

or Start.

2 Click · 2 Click · Scanning

Page 58 of the Lexmark 10E user manual — For Windows users
Page 58 · click to enlarge
Page 58

3 Click All Programs or Programs, and then select the printer program folder from the list.

4 Select Printer Home.

5 Choose your printer from the printer drop-down list.

6 Click Email, and then select Photo, Document or PDF.

Scanning starts and the scan progress dialog appears.

7 When the scan is finished, a new e-mail message is created with the scanned document automatically attached.

8 Compose your e-mail message.

For Macintosh users

1 Load an original document faceup into the ADF or facedown on the scanner glass.

2 From the Finder desktop, double-click the printer program folder.

3 Double-click the printer Center to open the All-In-One Center.

4 From the “What is being scanned?” menu on the main screen, select a document type.

5 From the “How will the scanned image be used?” menu, choose To be viewed on monitor/web page.

6 From the “Send scanned image to” menu, choose an application.

7 Click Scan.

8 Retrieve the scanned image from the application, and then send it through e-mail as an attachment.

Scanning to a PDF

For Windows users

1 Load an original document faceup into the ADF or facedown on the scanner glass.

or Start.

3 Click All Programs or Programs, and then select the printer program folder from the list.

4 Select Printer Home.

5 Choose your printer from the printer drop-down list.

6 Click PDF.

Scanning starts and the scan progress dialog appears.

7 Save the document as a PDF.

2 Click · Scanning

Page 59 of the Lexmark 10E user manual — Updating the application list
Page 59 · click to enlarge
Page 59

For Macintosh users

1 Load an original document faceup into the ADF or facedown on the scanner glass.

2 From the Finder desktop, double-click the printer program folder.

3 Double-click the printer Center to open the All-In-One Center.

4 From the “What is being scanned?” menu on the main screen, choose a document type.

5 Customize the settings as needed.

6 Click Scan.

7 Save the document as a PDF.

Scanning FAQ

How can I improve the quality of a scan?

  • Make sure your original documents are in good condition.
  • Make sure the application that receives the scanned document is appropriate. For example, if you are scanning a photo to edit it, then make sure you choose a photo editing application to receive the scan. If you are scanning a document to edit the text, then make sure you choose an OCR application.
  • Use a high resolution.

How do I scan in black and white?

Color is the default for all scans. To scan in black and white, press the Color/Black button on the printer control panel to switch from color to black and white.

Why am I being asked for a PIN?

PINs are a security measure used to restrict the scanned information from going into certain locations, or to keep what is being scanned from being seen or used by others. You may be prompted to enter a PIN if the network computer you are scanning to requires one.

To learn how PINs get assigned to network computers, see the Help for the printer software associated with your operating system.

What is an application list, and how do I update it?

When you scan a file, you can choose which application to use to open it on your computer. The printer downloads this application list from your computer when scanning for the first time. If you do not see the application you want on the list, or if you install new applications on your computer, then update the application list in the printer.

Updating the application list

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Computer or Network.

Scanning

Page 60 of the Lexmark 10E user manual — Canceling scan jobs
Page 60 · click to enlarge
Page 60

3 Select a local or network computer to receive the scan and then press

4 Select REFRESH from the list of scan applications.

This updates the application list in the printer.

Canceling scan jobs

on the printer control panel, or click Cancel on the computer screen.

Press · Scanning

Page 61 of the Lexmark 10E user manual — WPA/WPA2
Page 61 · click to enlarge
Page 61

Networking

Installing the printer on a wireless network

Wireless network compatibility

Your printer contains an IEEE 802.11g wireless print server. Your printer is compatible with IEEE 802.11 b/g/n routers that are Wi-Fi certified. If you are having issues with an n router, verify with your router manufacturer that the current mode setting is compatible with g devices, as this setting varies depending on the router brand/model.

Supported network security options

The printer supports three wireless security options: no security, WEP, and WPA/WPA2.

No Security

It is not recommended to use no security at all on a home wireless network. Using no security means that anyone within range of your wireless network can use your network resources—including Internet access, if your wireless network is connected to the Internet. The range of your wireless network may extend far beyond the walls of your home, allowing access to your network from the street or from your neighbors’ homes.

WEP

WEP (Wired Equivalent Privacy) is the most basic and the weakest type of wireless security. WEP security relies on a series of characters called the WEP key.

Every device on the wireless network must use the same WEP key. WEP security can be used on both ad hoc and infrastructure networks.

A valid WEP key has:

  • Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9

or • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, punctuation, and symbols found on a keyboard.

WPA/WPA2

WPA (Wi-Fi Protected Access) and WPA2 (Wi-Fi Protected Access 2) offer stronger wireless network security than WEP. WPA and WPA2 are similar types of security. WPA2 uses a more complex encryption method and is more secure than WPA. Both WPA and WPA2 use a series of characters, called the WPA pre-shared key or passphrase, to protect wireless networks from unauthorized access.

A valid WPA passphrase has:

  • From 8 to 63 ASCII characters. ASCII characters in a WPA passphrase are case-sensitive.

or • Exactly 64 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.

Networking

Page 62 of the Lexmark 10E user manual — Printing a network setup page
Page 62 · click to enlarge
Page 62

Every device on the wireless network must use the same WPA passphrase. WPA security is an option only on infrastructure networks with wireless access points and network cards that support WPA. Most newer wireless network equipment also offers WPA2 security as an option.

Printing a network setup page

A network setup page lists the configuration settings of the printer, including the IP address and MAC address of the printer.

1 Load plain paper.

2 From the printer control panel, press

3 Press the arrow buttons to scroll to Network Setup, and then press

to select Print Setup Page.

The network setup page prints.

Information you will need to set up the printer on a wireless network

To set up the printer for wireless printing, you need to know:

  • The name of your wireless network. This is also known as the Service Set Identifier (SSID).
  • If encryption was used to secure your network.
  • The security key (either a WEP key or WPA passphrase) that allows other devices to communicate on the network if encryption was used to secure your network.

You can locate your network WEP key or WPA passphrase by accessing your wireless access point or router and checking the security information.

If your wireless access point (wireless router) is using Wired Equivalent Privacy (WEP) security, the WEP key should be:

  • Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.

or • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, punctuation, and symbols found on a keyboard.

If your wireless access point is using Wi-Fi Protected Access (WPA) security, the WPA passphrase should be:

  • From 8 to 63 ASCII characters. ASCII characters in a WPA passphrase are case-sensitive.

or • Exactly 64 hexadecimal characters. Hexadecimal characters are A-F, a-f, and 0-9.

If your wireless network is not using security, then you will not have a security key.

Note: If you do not know the SSID of the network that your computer is connected to, launch the wireless utility of the computer network adapter and look for the network name. If you cannot find the SSID or the security information for your network, see the documentation that came with the wireless access point, or contact your system support person.

4 Press · Networking

Page 63 of the Lexmark 10E user manual — For Macintosh users
Page 63 · click to enlarge
Page 63

Installing the printer on a wireless network

Before you install the printer on a wireless network, make sure that:

  • Your wireless network is set up and working properly.
  • The computer you are using is connected to the same wireless network where you want to set up the printer.

For Windows users

1 Close all open software programs.

2 Insert the installation software CD.

If the Welcome screen does not appear after a minute, then launch the CD manually:

, or click Start and then click Run. b In the Start Search or Run box, type D:\setup.exe, where D is the letter of your CD or DVD drive.

3 Follow the instructions on the Welcome screen to set up the printer.

For Macintosh users

1 Close all open software applications.

2 Insert the installation software CD.

If the installation dialog does not appear after a minute, then click the CD icon on the desktop.

3 Double-click Install.

4 Follow the instructions on the installation dialog to set up the printer.

Installing the printer on other computers

Once the printer is set up on the wireless network, it can be accessed wirelessly by any other computer on the network. However, you will need to install the printer driver on every computer that will access it. You do not need to configure the printer again, although you will need to run the setup software on each computer to install the driver.

For Windows users

1 Close all open software programs.

2 Insert the installation software CD.

If the Welcome screen does not appear after a minute, then launch the CD manually:

, or click Start and then click Run. b In the Start Search or Run box, type D:\setup.exe, where D is the letter of your CD or DVD drive.

3 Follow the instructions on the computer screen for installing a configured printer on a new computer.

For Macintosh users

1 Close all open software applications.

2 Insert the installation software CD.

If the installation dialog does not appear after a minute, then click the CD icon on the desktop.

3 Double-click Install.

a Click · a Click · Networking

Page 64 of the Lexmark 10E user manual — Adding the printer to your wireless network
Page 64 · click to enlarge
Page 64

4 Select My printer is already set up. I am installing it on a new computer.

5 Click Continue, and then follow the instructions on the computer screen for installing a configured printer on a new computer.

Interpreting the colors of the Wi-Fi indicator light

The colors of the Wi-Fi indicator light show the network status of the printer.

  • Off means one of the following: – The printer is turned off or is powering up. – The printer is not connected to a wireless network and is in Power Saver mode. In Power Saver mode, the

power light pulses on and off. • Solid orange means one of the following: – The printer has not yet been configured for a wireless network. – The printer is configured for an ad hoc connection, but it is not currently communicating with another ad hoc

device. • Blinking orange means one of the following: – The printer is out of the range of the wireless access point (wireless router). – The printer is trying to communicate with the wireless access point, but the wireless access point is turned

off or not working properly. – Either the configured printer or the wireless access point has been turned off and back on, and the printer is

trying to establish communications with the network. – The wireless settings of the printer may no longer be valid. • Green means that the printer is connected to a wireless network and is ready for use.

Special wireless installation instructions

The following instructions apply to customers outside of North America who are using a wireless broadband box. Some examples of these boxes include LiveBox, AliceBox, N9UF Box, FreeBox, and Club Internet.

Before you begin

  • Make sure your box is wireless-enabled and activated to work on a wireless network. For more information about configuring the box to work wirelessly, see the documentation that came with your box.
  • Make sure your box is turned on and that your computer is on and connected to your wireless network.

Adding the printer to your wireless network

1 Set up your printer for wireless networking using the setup instructions provided.

Stop when you are prompted to select a network.

2 If there is an association/registration button on the back of your box, press it before selecting a network.

3 Return to the computer screen.

From the wireless networks list that appears, select your network, and then click Continue.

Networking

Page 65 of the Lexmark 10E user manual — For Windows users
Page 65 · click to enlarge
Page 65

If your wireless network does not appear in the list:

a Connect to another wireless network.

For Windows users

Click Unlisted Network.

For Macintosh users

Select Other Wireless Network, and then click Continue. b Enter the details about your wireless network.

4 Follow the instructions on your screen to complete installation.

Assigning a static IP address

The printer will be assigned an IP address automatically through DHCP on most wireless networks.

1 Complete the wireless setup, allowing the printer to receive a DHCP address from a DHCP server on the network.

2 Print a network setup page to see what IP address is currently assigned to the printer.

3 Open a Web browser and then type the printer IP address in the address field. Press Enter.

The printer Web page loads.

4 Click the Configuration link.

5 Click the TCP/IP link.

6 Click the Set static IP address link.

7 Type the IP address you want to assign to the printer in the IP Address field.

8 Click the Submit button.

The Submitting selection message appears.

To confirm that the address was successfully assigned, type the static IP address in the Web browser address field and then press Enter. The printer Web page loads if the address was successfully assigned.

For more information, contact your system support person.

Changing wireless settings after installation

To change wireless settings on the printer, such as the configured network, the security key, or other settings, do the following:

For Windows users

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.

3 Select Printer Home.

1 Click · Networking

Page 66 of the Lexmark 10E user manual — In Windows Vista
Page 66 · click to enlarge
Page 66

4 Click the Settings tab.

5 Click the Wireless setup utility link.

6 Follow the instructions on the computer screen to configure the printer for wireless access with the new settings.

For Macintosh users

1 From the Finder desktop, double-click the printer folder.

2 Double-click Wireless Setup Assistant.

3 Follow the instructions on the computer screen.

Advanced wireless setup

Creating an ad hoc wireless network

The recommended way to set up your wireless network is to use a wireless access point (wireless router). A network set up this way is called an infrastructure network. If you have an infrastructure network, you should configure the printer for use on that network.

You can set up an ad hoc network if you:

  • Do not have an access point or wireless router
  • Do not already have a wireless network (but do have a wireless adapter for your computer)
  • Want to set up a standalone network between the printer and a computer with a wireless network adapter

In Windows Vista

2 Click Control Panel.

3 Click Network and Internet.

4 Under Network and Sharing Center, click Connect to a network.

5 Click Set up a connection or network when you are prompted to select a network to connect to.

6 Click Set up a wireless ad-hoc (computer-to-computer) network, when you are prompted to choose a connection option, and then click Next.

7 Follow the instructions in the “Set up a wireless ad hoc network” wizard. As part of the setup: a Create a network name or SSID for the network between the computer and your printer. b Write down the name of your network. Be sure to use the exact spelling and capitalization.

c Go to the Security Type list, select WEP, and then create a WEP key.

1 Click · Networking

Page 67 of the Lexmark 10E user manual — In Windows XP
Page 67 · click to enlarge
Page 67

WEP keys must be:

  • Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A-F, a–f, and 0-9. or
  • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard d Write down the password for your network. Be sure to use the exact spelling and capitalization.

Windows Vista will enable the ad hoc network for you. It will appear in the “Connect to a network” dialog under “Available networks,” indicating that the computer is configured for the ad hoc network.

8 Close the Windows Control Panel and any remaining windows.

9 Insert the installation software CD, and follow the directions for wireless installation.

10 When the available networks are displayed, provide the network name and the security information you created in step 6. The installer will configure the printer for use with your computer.

11 Store a copy of your network name and security information in a safe place for future reference.

In Windows XP

1 Click Start.

2 Click Control Panel.

3 Click Network and Internet Connections.

4 Click Network Connections.

5 Right-click the icon for your wireless network connection.

6 Click Enable, if it appears in the pop-up menu.

7 Right-click the Wireless Network Connection icon.

8 Click Properties.

9 Click the Wireless Networks tab.

10 Select the Use Windows to configure my wireless network settings check box.

11 Under Preferred Networks, delete any existing networks. a Select the network to be removed. b Click Remove to delete the network from the list.

12 Click Add to create an ad hoc network.

13 In the Network Name (SSID) box, type the name you want to give your wireless network.

14 Write down the network name you chose so you can refer to it when running the wireless setup. Be sure to use the exact spelling and capitalization.

Networking

Page 68 of the Lexmark 10E user manual — In Mac OS X version 10.4 and earlier
Page 68 · click to enlarge
Page 68

15 If Network Authentication appears in the list, select Open.

16 In the “Data encryption” list, select WEP.

17 If necessary, clear the “The key is provided for me automatically” check box.

18 In the Network Key box, type in a WEP key.

19 Write down the WEP key you chose so you can refer to it when running the wireless setup. Make sure you copy it down exactly, including any capital letters.

20 In the “Confirm network key” box, type the same WEP key.

21 Select This is a computer-to-computer (ad hoc) network; wireless access points are not used.

22 Click OK twice to close the two open windows.

23 It may take a few minutes for your computer to recognize the new settings. To check on the status of your network: a Right-click the Wireless Network Connections icon. b Select View Available Wireless Networks.

  • If the network is listed but the computer is not connected, select the ad hoc network and then click Connect .
  • If the network does not appear, wait a minute and then click Refresh network list .

24 Insert the installation software CD, and follow the directions for wireless installation.

25 When the available networks are displayed, provide the network name and the security information you created beginning in step 13. The installer will configure the printer for use with your computer.

26 Store a copy of your network name and security information in a safe place for future reference.

In Windows 2000

  • Refer to the documentation that came with your wireless network adapter for information on configuring an ad hoc network with Windows 2000.

For Macintosh users

1 Access the Airport settings:

In Mac OS X version 10.5

a From the Apple menu, choose System Preferences. b Click Network.

c Click AirPort.

In Mac OS X version 10.4 and earlier

a From the Finder desktop, choose Go > Applications. b From the Applications folder, double-click Internet Connect.

c From the toolbar, click AirPort.

2 From the Network menu, click Create Network.

Networking

Page 69 of the Lexmark 10E user manual — Configuring the printer wirelessly using WPS (Wi-Fi Protected Setup)
Page 69 · click to enlarge
Page 69

3 Create a name for the ad hoc network, and then click OK.

Adding a printer to an existing ad hoc wireless network

For Windows users

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.

3 Select Printer Home.

4 Click the Settings tab.

5 Click Wireless setup utility link.

6 Follow the instructions on the computer screen.

For Macintosh users

1 From the Finder desktop, double-click the printer folder.

2 Double-click Wireless Setup Assistant.

3 Follow the instructions on the computer screen.

Configuring the printer wirelessly using WPS (Wi-Fi Protected Setup)

Wi-Fi Protected Setup (WPS) is a method of configuring computers and printers on a secure wireless network. WPS is faster than manual configuration, and it reduces typing errors when new devices are added to a wireless network. The SSID and WPA passphrase are automatically detected and configured for you. The printer supports WPS and can be configured for wireless access using WPS. In order to use WPS to configure the printer, the wireless router must also support WPS.

If you want to use WPS to set up your printer, then insert the CD and follow the instructions on the computer screen.

  • To use WPS to configure the printer wirelessly, all of the devices on your wireless network must support WPS. If any device on your network does not support WPS, then you must type the SSID and security information when prompted.
  • If you are using the PIN method to add your printer using WPS, make sure you type all eight digits when you are asked to enter your PIN.

1 Click · Networking

Page 70 of the Lexmark 10E user manual — Using the printer wirelessly
Page 70 · click to enlarge
Page 70

Switching between USB and wireless connections (Windows only)

You can change the way you access your printer, depending on your needs. The following procedures assume that you have configured your printer for one type of connection and that the printer drivers are installed on the computer. See related topics on troubleshooting specific connection types if you encounter difficulties during configuration.

Using the printer wirelessly

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.

3 Select Printer Home.

4 Click the Settings tab.

5 Click the Wireless setup utility link.

6 Follow the instructions on the computer screen to set up the printer wirelessly.

Using the printer locally (USB)

1 Attach a USB cable to the computer and to the printer.

2 Wait a moment for Windows to locate the driver and finish setting up the printer.

Switching between USB and wireless connections (Macintosh only)

You can change the way you access your printer depending on your needs. The procedures below assume that you have configured your printer for one type of connection. See related topics on troubleshooting specific connection types if you encounter difficulties during configuration.

Using the printer wirelessly

If the printer is currently set up locally (using USB connection)

1 Close all open software applications.

2 Insert the installation software CD.

If the installation dialog does not appear after a minute, then click the CD icon on the desktop.

3 Double-click the Lexmark Extras folder.

4 Double-click Lexmark Setup Assistant.

5 Follow the instructions on the computer screen for configuring the printer wirelessly.

1 Click · Networking

Page 71 of the Lexmark 10E user manual — Sharing a printer in a Windows environment
Page 71 · click to enlarge
Page 71

Using the printer locally (USB)

If the printer is currently set up for wireless

1 Attach one end of a USB cable to the USB port on the back of the printer. Attach the other end to a USB port on the computer.

2 Check if a second print queue is automatically created.

In Mac OS X version 10.5

a From the Apple menu, choose System Preferences. b Click Print & Fax under the Hardware section.

In Mac OS X version 10.4 or earlier

a From the Finder desktop, choose Go > Utilities. b Double-click Print Center or Printer Setup Utility, depending on the operating system version you are using.

The Printer List dialog appears. c Choose the printer you want to use.

3 If a second print queue is not created, manually add the printer.

In Mac OS X version 10.5

a Click +. b Select the printer from the list, and then click Add.

In Mac OS X version 10.4 or earlier

a Click Add.

The Printer Browser appears. b Select your printer.

c Click Add.

4 Remove the wireless queue if you do not want to switch back to accessing the printer over a wireless connection.

Sharing a printer in a Windows environment

1 Prepare the computers to share the printer: a Make all computers printing to the printer accessible through Network Neighborhood by enabling File and

Print Sharing. See the Windows documentation for instructions on enabling File and Print Sharing. b Install the printer software on all computers that will print to the printer.

2 Identify the printer: a On the computer that is attached to the printer, do one of the following:

, or click Start and then click Run. 2 In the Start Search or Run box, type control printers. 3 Press Enter, or click OK. The printer folder opens. b Right-click the name of your printer.

c Click Sharing.

1 Click · Networking

Page 72 of the Lexmark 10E user manual — Sharing a printer in a Macintosh environment
Page 72 · click to enlarge
Page 72

d From the Sharing tab, select Share this printer or Shared as, and then assign a distinctive name. e Click OK.

3 Locate the printer from the remote computer:

, or click Start and then click Run. 2 In the Start Search or Run box, type control printers. 3 Press Enter, or click OK. The printer folder opens. b Right-click the name of your printer.

c Click Properties. d Click the Ports tab, and then click Add Port. e Select Local Port, and then click New Port.

f Type the Universal Naming Convention (UNC) Port name, which consists of the server name and the distinctive printer name that was specified in step 2 on page 71. The name should be in the form \\server \printer.

g Click OK. h Click Close on the Printer Ports dialog.

i Make sure the new port is selected on the Ports tab, and then click Apply. The new port is listed with the printer name. j Click OK.

Sharing a printer in a Macintosh environment

1 From the Apple menu, choose System Preferences.

2 From the menu bar, click Help System Preferences Help.

3 In the Search field, type sharing the printer on a network, and then press return.

4 To let other Macintosh computers on the network that use Mac OS X version 10.3 or later use any printer connected to your Macintosh computer, double-click Sharing your printer with Mac OS X users.

To let Windows computers on the network use any printer connected to your Macintosh computer, double-click Sharing your printers with Windows users.

5 Follow the instructions on the computer screen.

1 Click · or · Networking

Page 73 of the Lexmark 10E user manual — What is an SSID?
Page 73 · click to enlarge
Page 73

Networking FAQ

What is Wi-Fi Protected Setup?

Wi-Fi Protected Setup (WPS) is a simple and secure configuration that allows you to establish a wireless home network and enable network security without requiring prior knowledge of Wi-Fi technology. It is no longer necessary to configure the network name (SSID) and WEP key or WPA passphrase for network devices.

The printer supports the following methods in connecting to a wireless network:

  • Personal Identification Number (PIN)—A PIN on the printer is entered into the wireless settings of the wireless access point.
  • Push Button Configuration (PBC)—Buttons on both the printer and the wireless access point are pushed within a given period of time.

Look for any of these identifier marks to check if your wireless access point is WPS certified:

You can find these WPS logos on the side, back, or top of your wireless access point.

For more information on accessing the wireless settings and determining the WPS capability of your wireless access point, see the documentation that came with the wireless access point or contact your system support person.

Where do I find my WEP key or WPA passphrase?

To find the WEP key or WPA passphrase for the wireless network, view the security settings on the access point or wireless router. Most access points have a Web page that can be accessed using a Web browser.

You can also check the manual that came with your access point or router. If your access point or router is using the default settings, you can find the information in the manual. If someone else set up your network for you, that person or company may have included the information in the manual.

If you do not know how to access the Web page, or if you do not have administrator access to the wireless access point on your network, and are unable to locate the information in the manual, contact your system support person.

What is an SSID?

A Service Set Identifier (SSID) is the name that identifies a wireless network. All devices on the network must know the SSID of the wireless network or they will not be able to communicate with each other. Usually, the wireless network broadcasts the SSID to allow wireless devices in the area to connect to it. Sometimes, the SSID is not broadcast for security reasons.

If the SSID of your wireless network is not broadcast, it cannot be detected automatically and will not show up in the list of available wireless networks. You must enter the network information manually in this situation.

An SSID can contain up to 32 alphanumeric characters.

Networking

Page 74 of the Lexmark 10E user manual — Wireless network examples
Page 74 · click to enlarge
Page 74

Where do I find my SSID?

You can find the SSID for the wireless network by viewing the settings on the access point or wireless router. Most access points have a built-in Web server that can be accessed using a Web browser.

Many network adapters provide a software application that allows you to view the wireless settings of your computer, including your SSID. Check your computer to see if a program was installed with your network adapter.

If you are unable to locate your SSID using either of these methods, contact your system support person.

What is a network?

A network is a collection of devices such as computers, printers, Ethernet hubs, wireless access points, and routers connected together for communication through cables or through a wireless connection. A network can be wired, wireless, or designed to have both wired and wireless devices.

Devices on a wired network use cables to communicate with each other.

Devices on a wireless network use radio waves instead of cables to communicate with each other. For a device to be able to communicate wirelessly, it must have a wireless network adapter attached or installed that lets it receive and transmit radio waves.

How do I find out what type of security my network is using?

You must know the WEP key or WPA passphrase and the type of security (WEP, WPA, or WPA2) used on the wireless network. To obtain this information, see the documentation that came with your wireless access point (wireless router), see the Web page associated with the wireless access point, or consult your system support person.

How are home networks configured?

For desktop computers, laptops, and printers to communicate with each other over a network, they must be connected by cables and/or have wireless network adapters built in or installed in them.

There are many different ways a network can be set up. Four common examples appear below.

Wireless network examples

Scenario 1Mixed wired and wireless connections on a network with Internet access
  • All computers and printers connect to the network through a router with Ethernet and wireless capabilities.
  • Some computers and printers connect wirelessly to the router; others connect over a wired connection.

Networking

Page 75 of the Lexmark 10E user manual — Scenario 3: Wireless network with no Internet access
Page 75 · click to enlarge
Page 75
  • The network is connected to the Internet through a DSL or cable modem.
Lexmark 10E — Where do I find my SSID? diagram (page 75)
Fig. 29 · Where do I find my SSID?

Scenario 2: Wireless network with Internet access

  • All computers and printers connect to the network using a wireless access point or wireless router.
  • The wireless access point connects the network to the Internet through a DSL or cable modem.
Lexmark 10E — Scenario 2: Wireless network with Internet access diagram (page 75)
Fig. 30 · Scenario 2: Wireless network with Internet access

Scenario 3: Wireless network with no Internet access

  • Computers and printers connect to the network using a wireless access point.
  • The network has no connection to the Internet.
Lexmark 10E — Scenario 3: Wireless network with no Internet access diagram (page 75)
Fig. 31 · Scenario 3: Wireless network with no Internet access

Networking

Page 76 of the Lexmark 10E user manual — How do I attach the installation cable?
Page 76 · click to enlarge
Page 76

Scenario 4: Computer connected wirelessly to a printer without Internet access

  • A computer is directly connected to a printer without going through a wireless router.
  • This configuration is referred to as an ad hoc network .
  • The network has no connection to the Internet.
Lexmark 10E — Scenario 4: Computer connected wirelessly to a printer without Internet access diagram (page 76)
Fig. 32 · Scenario 4: Computer connected wirelessly to a print…

Why do I need an installation cable?

When setting up the printer on your wireless network, the printer will need to temporarily connect to a computer using the installation cable. This temporary connection is used to set up the wireless settings of the printer.

The installation cable connects to a rectangular USB port on the installing computer and the square USB port on the printer.

How do I attach the installation cable?

The installation cable attaches to a USB port on the computer and to the square connector on the back of the printer. This connection allows you to configure the printer for a networked or locally attached installation.

1 Attach the large, rectangular connector to any USB port on your computer. USB ports may be on the front or the back of the computer, and may be horizontal or vertical.

Lexmark 10E — How do I attach the installation cable? diagram (page 76)
Fig. 33 · How do I attach the installation cable?

Networking

Page 77 of the Lexmark 10E user manual — How are infrastructure and ad hoc networks different?
Page 77 · click to enlarge
Page 77

2 Attach the small, square connector to the printer.

Lexmark 10E — How are infrastructure and ad hoc networks different? diagram (page 77)
Fig. 34 · How are infrastructure and ad hoc networks different…

3 Continue following the on-screen instructions.

How are infrastructure and ad hoc networks different?

Wireless networks can operate in one of two modes: infrastructure or ad hoc.

In infrastructure mode, all devices on a wireless network communicate with each other through a wireless router (wireless access point). Devices on the wireless network must have valid IP addresses for the current network and share the same SSID and channel as the wireless access point.

In ad hoc mode, a computer with a wireless network adapter communicates directly with a printer equipped with a wireless print server. The computer must have a valid IP address for the current network and be set to ad hoc mode. The wireless print server must be configured to use the same SSID and channel that the computer is using.

The following table compares the characteristics and requirements of the two types of wireless networks.

Communication Through wireless access point Directly between devices

Security More security options WEP or no security

Range Determined by range and number of wireless access points

Restricted to range of individual devices on network

Speed Usually faster Usually slower

Requirements for all devices

Unique IP address for each device Yes Yes

Mode set to Infrastructure mode Ad hoc mode

Same SSID Yes, including the wireless access point

Same channel Yes, including the wireless access point

We recommend setting up a network in infrastructure mode using the installation CD that came with the printer.

Show 5 more labels / short text on this page
Infrastructure Ad hoc · Characteristics · Yes · Yes · Networking
Page 78 of the Lexmark 10E user manual — R EMOVE OBSTACLES BETWEEN THE ACCESS POINT AND THE PRINTER
Page 78 · click to enlarge
Page 78

Infrastructure mode is the recommended setup method because it provides:

  • Increased network security
  • Increased reliability
  • Faster performance
  • Easier setup

Finding the signal strength

Wireless devices have built-in antennas that transmit and receive radio signals. The signal strength listed on the printer network setup page indicates how strongly a transmitted signal is being received. Many factors can affect the signal strength. One factor is interference from other wireless devices or other devices such as microwave ovens. Another factor is distance. The farther two wireless devices are from each other, the more likely it is that the communication signal will be weaker.

The strength of the signal received by your computer can also affect the connectivity of the printer with the network during configuration. When you installed the wireless adapter in your computer, the adapter software probably placed an icon in your system tray. Try double-clicking this icon, and it will tell you how strongly the computer is receiving the wireless signal from the network.

To improve signal quality, remove sources of interference and/or move wireless devices closer to the wireless access point (wireless router).

How can I improve wireless signal strength?

A common reason wireless printers fail to communicate over a network is poor wireless signal quality. If the signal is too weak, too distorted, or blocked by an object, it cannot carry information between the access point and the printer. To determine if the printer is receiving a strong signal from the access point, print a network setup page. The Quality field indicates the relative strength of the wireless signal the printer is receiving. Drops in signal strength can be intermittent, however, and although the signal quality appears high, it may drop during certain conditions.

If you think signal strength is a problem between your access point and the printer, try one or more of the following:

  • The solutions below are for infrastructure networks. If you are using an ad hoc network, adjust the computer when the solution suggests adjusting the access point.
  • Ad hoc networks have a much shorter range than infrastructure networks. Try moving the printer closer to the computer if they seem to have trouble communicating.

MOVE THE PRINTER CLOSER TO THE WIRELESS ACCESS POINT/WIRELESS ROUTER

If the printer is too far away from the access point, it will not be able to communicate with other devices on the network. For most indoor wireless networks, the maximum distance between the access point and the printer is approximately 100 feet (30 meters). This distance could be longer or shorter, depending upon the layout of the network and the limitations of the access point.

R EMOVE OBSTACLES BETWEEN THE ACCESS POINT AND THE PRINTER

The wireless signal from your access point will pass through most objects. Most walls, floors, furniture and other objects will not block the wireless signal. However, there are materials that are too dense for the signal to pass through. Objects containing metal and concrete can block the signal. Arrange your printer and access point so that the signal is not blocked by such objects.

Networking

Page 79 of the Lexmark 10E user manual — For Windows users
Page 79 · click to enlarge
Page 79

R EMOVE SOURCES OF INTERFERENCE

Other types of radio frequencies can cause problems with the wireless signal on your network. These sources of interference can cause printing issues that seem to come and go. Turn off potential sources of interference where possible. Avoid using microwaves and cordless phones when printing over your wireless network.

If another wireless network is operating in the vicinity, change the wireless channel on the access point.

Do not place your access point on a printer or other electronic device. Such devices can also interfere with the wireless signal.

A RRANGE THE NETWORK TO REDUCE SIGNAL ABSORPTION

Even when the wireless signal is able to pass through an object, it is slightly weakened. If it passes through too many objects, it can be significantly weakened. All objects absorb part of the wireless signal when it passes through them, and certain types of objects absorb enough to cause communications problems. Place your access point as high in the room as possible to avoid signal absorption.

How can I make sure my computer and printer are connected to the same wireless network?

If the printer is not on the same wireless network as the computer, you will not be able to print wirelessly. The SSID of the printer must match the SSID of the computer, if the computer is already connected to the wireless network.

For Windows users

1 Obtain the SSID of the network that the computer is connected to: a Type the IP address of your wireless access point (wireless router) into the address field of your Web browser.

If you do not know the IP address of the wireless access point:

  • , or click Start and then click Run . 2 In the Start Search or Run box, type cmd . 3 Press Enter , or click OK . The Command Prompt window opens. 4 Type ipconfig , and then press Enter . Check the Wireless Network Connection section:
  • The “Default Gateway” entry is typically the wireless access point.
  • The IP address appears as four sets of numbers separated by periods, such as 192.168.2.134. b Type the user name and password of the router when prompted.

c Click OK. d On the main page, click Wireless or any other selection where settings are stored. The SSID will be displayed. e Write down the SSID.

2 Print the printer network setup page.

In the Wireless section, look for SSID.

1 Click · Networking

Page 80 of the Lexmark 10E user manual — For Macintosh users with a wireless access point
Page 80 · click to enlarge
Page 80

3 Compare the SSID of the computer and SSID of the printer.

If the SSIDs are the same, then the computer and the printer are connected to the same wireless network.

If the SSIDs are not the same, then run the utility again to set up the printer on the wireless network used by the computer.

For Macintosh users with an AirPort base station

In Mac OS X version 10.5

1 From the Apple menu, choose System Preferences.

2 Click Network.

3 Click AirPort.

The SSID of the network the computer is connected to is displayed in the Network Name pop-up menu.

4 Write down the SSID.

In Mac OS X version 10.4 and earlier

1 From the Finder desktop, choose Go > Applications.

2 From the Applications folder, double-click Internet Connect.

3 From the toolbar, click AirPort.

The SSID of the network the computer is connected to is displayed in the Network pop-up menu.

4 Write down the SSID.

For Macintosh users with a wireless access point

1 Type the IP address of the wireless access point in the address field of your Web browser and continue to step 2.

If you do not know the IP address of the wireless access point, then do the following:

a From the Apple menu, choose System Preferences. b Click Network.

c Click AirPort. d Click TCP/IP, or click Advanced, and then click TCP/IP.

2 Type your user name and password when prompted.

3 Click OK.

4 On the main page, click Wireless or another selection where settings are stored. The SSID will be displayed.

5 Write down the SSID, security type and the WEP key/WPA passphrase (if shown).

  • Make sure you copy the network information down exactly, including any capital letters.
  • Store the SSID and the WEP key or WPA passphrase in a safe place for future reference.

Networking

Page 81 of the Lexmark 10E user manual — How do I find the MAC address?
Page 81 · click to enlarge
Page 81

Can I use my printer on a USB and a network connection at the same time?

Yes, the printer supports a simultaneous USB and network connection. The printer can be configured in the following ways:

  • Locally attached (connected to a computer using a USB cable)
  • Wireless network
  • Wireless network and locally attached simultaneously

What is a MAC address?

A Media Access Control (MAC) address is a 48-bit identifier associated with the hardware of network equipment. The MAC address may also be called the physical address because it is connected to the hardware of a device instead of its software. The MAC address is displayed as a hexadecimal number in this format: 01-23-45-67-89-AB.

Every device capable of communicating on a network has a MAC address. Network printers, computers, and routers, whether Ethernet or wireless, all have MAC addresses.

While it is possible to change the MAC address of a network device, it is not common practice to do so. For this reason, MAC addresses are considered permanent. IP addresses are easily changed, so MAC addresses are a more reliable method of identifying a specific device on a network.

Routers with security capabilities may allow filtering of MAC addresses on networks. This allows a managed list of devices to access the network, identified by their MAC addresses. MAC address filtering can help prevent access on the network from unwanted devices, such as from intruders on a wireless network. MAC address filtering can also prevent legitimate access if you forget to add a new device to the router's list of allowed addresses. If your network uses MAC address filtering, be sure to add the MAC address of the printer to the list of allowed devices.

How do I find the MAC address?

Most network equipment has a unique hardware identification number to distinguish it from other devices on the network. This is called the Media Access Control (MAC) address.

When installing the printer on a network, make sure you select the printer with the correct MAC address.

The MAC address label is located inside the printer.

Lexmark 10E — How do I find the MAC address? diagram (page 81)
Fig. 35 · How do I find the MAC address?

Networking

Page 82 of the Lexmark 10E user manual — For Windows users
Page 82 · click to enlarge
Page 82

The MAC address of the internal print server is a series of letters and numbers. Other devices sometimes use a type of MAC address called Universally Administered Address (UAA).

Lexmark 10E — What is an IP address? diagram (page 82)
Fig. 36 · What is an IP address?
Lexmark 10E — What is an IP address? diagram (page 82)
Fig. 37 · What is an IP address?

Note: A list of MAC addresses can be set on an access point (router) so that only devices with matching MAC addresses are allowed to operate on the network. This is called MAC filtering. If MAC filtering is enabled in your access point and you want to add a printer to your network, then the MAC address of the printer must be included in the MAC filter list.

What is an IP address?

An IP address is a unique number used by devices (such as a wireless printer, computer, or wireless access point) on an IP network to locate and communicate with each other. Devices on an IP network can communicate with each other only if they have unique and valid IP addresses. A unique IP address means no two devices on the same network have the same IP address.

An IP address is a group of four numbers separated by periods. An example of an IP address is 192.168.100.110.

What is TCP/IP?

Networks are able to function because computers, printers, and other devices are able to send data to each other, either through cables or by using wireless signals. This transfer of data is made possible by sets of data transmission rules called protocols. A protocol can be thought of as a language, and like a language, it has rules allowing participants to communicate with each other.

Different types of networks use different protocols, but Transmission Control Protocol/Internet Protocol (TCP/IP) is the most popular. TCP/IP is used to send data over the Internet as well as over most corporate and home networks.

Because computers do not understand words and instead rely upon numbers for communication, TCP/IP requires that every device on a network using TCP/IP to communicate must have an IP address. IP addresses are essentially unique computer names in a numeric format, used to transfer data around a network. IP addresses allow TCP/IP to confirm requests for and receipt of data by various devices on the network.

How do I locate IP addresses?

For Windows users

, or click Start and then click Run.

2 In the Start Search or Run box, type cmd.

3 Press Enter, or click OK.

The Command Prompt window opens.

4 Type ipconfig, and then press Enter.

The IP address appears as four sets of numbers separated by periods, such as 192.168.0.100.

1 Click · Networking

Page 83 of the Lexmark 10E user manual — What is a key index?
Page 83 · click to enlarge
Page 83

For Macintosh users

1 From the Apple menu, choose About This Mac.

2 Click More Info.

3 From the Contents pane, choose Network.

4 If you are connected over a wireless network, choose AirPort from the Active Services list.

How to locate a printer IP address

  • You can locate the printer IP address by viewing the printer network setup page.

How are IP addresses assigned?

An IP address may be assigned automatically by the network using DHCP. Once the printer is set up on a computer, the computer sends all print jobs across the network to the printer using this address.

If the IP address is not automatically assigned, you will be asked during wireless setup to manually enter an address and other network information after selecting your printer from the available list.

What is a key index?

A wireless access point (wireless router) can be configured with as many as four WEP keys. Only one key is used on the network at a time, however. The keys are numbered, and the number of a key is referred to as its key index. All devices on the wireless network must be configured to use the same key index when multiple WEP keys are configured on the wireless access point.

Select the same key index on your printer as you are using on your wireless access point.

Networking

Page 84 of the Lexmark 10E user manual — Using the printer control panel
Page 84 · click to enlarge
Page 84

Maintaining the printer

Maintaining ink cartridges

In addition to the following tasks that you can perform, your printer performs an automatic maintenance cycle every week if it is plugged into an electrical outlet. It will briefly come out of Power Saver mode or will temporarily power on if it is turned off.

Checking ink levels

Using the printer control panel

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Maintenance, and then press

again to select Ink Levels.

4 Press the arrow buttons to check the ink level in each cartridge.

Using the printer software

For Windows users

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.

3 Select Printer Home.

4 Choose your printer from the printer drop-down list.

5 From the Maintenance tab, click Check ink levels.

For Macintosh users

1 From the Finder desktop, double-click the printer program folder.

2 Select Printer Utility from the list.

3 Check the ink levels from the Maintenance tab.

Aligning the printhead

If the characters or lines on your printer image appear jagged or wavy, then you may need to align the printhead.

Using the printer control panel

1 Load plain paper.

2 From the printer control panel, press

3 Press the arrow buttons to scroll to Maintenance, and then press

3 Press · 1 Click · Maintaining the printer

Page 85 of the Lexmark 10E user manual — Using the printer control panel
Page 85 · click to enlarge
Page 85

4 Press the arrow buttons to scroll to Align Printer, and then press

again.

An alignment page prints.

Using the printer software

For Windows users

1 Load plain paper.

or Start.

3 Click All Programs or Programs, and then select the printer program folder from the list.

4 Select Printer Home.

5 Choose your printer from the printer drop-down list.

6 From the Maintenance tab, click Align cartridges.

7 Follow the instructions on the computer screen.

For Macintosh users

1 Load plain paper.

2 From the Finder desktop, double-click the printer program folder.

3 Select Printer Utility from the list.

4 From the Maintenance tab of the Printer Utility dialog, click Print Alignment Page.

5 Follow the instructions on the computer screen.

If you aligned the cartridges to improve print quality, then print your document again. If print quality has not improved, then clean the printhead nozzles.

Cleaning the printhead nozzles

Poor print quality is sometimes due to clogged printhead nozzles. Clean the printhead nozzles to improve the quality of your prints.

  • Cleaning the printhead nozzles uses ink, so clean them only when necessary.
  • Deep cleaning uses more ink, so try the Clean Printhead option first to save ink.
  • If the ink levels are too low, you must replace the ink cartridges before you can clean the printhead nozzles.

Using the printer control panel

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Maintenance, and then press

5 Press · 2 Click · Maintaining the printer

Page 86 of the Lexmark 10E user manual — Cleaning the scanner glass
Page 86 · click to enlarge
Page 86

3 Press the arrow buttons to scroll to Clean Printhead or Deep Clean Printhead, and then press

to clean the printhead nozzles.

A cleaning page prints.

Using the printer software

For Windows users

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.

3 Select Printer Home.

4 From the Maintenance tab, click Clean Cartridges.

For Macintosh users

1 From the Finder desktop, double-click the printer program folder.

2 Select Printer Utility from the list.

3 From the Maintenance tab, select Clean Print Nozzles.

A cleaning page prints.

Cleaning the exterior of the printer

1 Make sure that the printer is turned off and unplugged from the wall outlet.

2 Remove paper from the paper support and paper exit tray.

3 Dampen a clean, lint-free cloth with water.

4 Wipe only the outside of the printer, making sure to remove any ink residue that has accumulated on the paper exit tray.

5 Make sure the paper support and paper exit tray are dry before beginning a new print job.

Cleaning the scanner glass

1 Dampen a clean, lint-free cloth with water.

2 Gently wipe the scanner glass clean.

4 Press · 1 Click · Maintaining the printer

Page 87 of the Lexmark 10E user manual — Setup troubleshooting
Page 87 · click to enlarge
Page 87

Troubleshooting

Before you troubleshoot

Use this checklist to solve most printer problems:

  • Make sure the power cord is plugged into the printer and into a working electrical outlet.
  • Make sure the printer is not plugged into any surge protectors, uninterrupted power supplies, or extension cords.
  • Make sure the printer is turned on.
  • Make sure the printer is securely connected to the host computer, print server, or other network access point.
  • Check the printer for error messages, and resolve any errors.
  • Check for paper jam messages, and clear any jams.
  • Check the ink cartridges, and install new cartridges if necessary.
  • Use the Service Center to locate and solve the problem (Windows only).
  • Turn the printer off, wait about 10 seconds, and then turn the printer back on.

Using the Service Center to solve printer problems

The Service Center provides step-by-step troubleshooting help and contains links to printer maintenance tasks and customer support.

To open the Service Center, use one of these methods:

Method 1 Method 2

If it appears on an error message dialog, click the For additional assistance, use the Service Center link.

or Start. 2 Click All Programs or Programs, and then select the printer program folder from the list. 3 Select Printer Home. 4 From the Support tab, select Service Center.

If Troubleshooting does not solve your problem

Visit our Web site at support.lexmark.com to find the following:

  • Knowledgebase articles with the latest information and troubleshooting for your printer
  • Live online technical support
  • Contact numbers for telephone technical support

Setup troubleshooting

  • “Incorrect language appears on the display” on page 88
  • “Printhead errors” on page 88
  • “Software did not install” on page 90

1 Click · Troubleshooting

Page 88 of the Lexmark 10E user manual — Printhead errors
Page 88 · click to enlarge
Page 88
  • “Print job does not print or is missing pages” on page 90
  • “Printer is printing blank pages” on page 91
  • “Printer is busy or does not respond” on page 91
  • “Cannot delete documents from the print queue” on page 92
  • “Cannot print through USB” on page 92

Incorrect language appears on the display

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

C HANGE THE LANGUAGE USING THE PRINTER MENUS

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Defaults, and then press

3 Press the arrow buttons to scroll to Set Defaults, and then press

4 Press the arrow buttons to scroll to Use Factory, and then press

5 Complete the initial printer setup.

CHANGE THE LANGUAGE USING A BUTTON COMBINATION (IF YOU CANNOT READ THE CURRENT

LANGUAGE )

1 Turn the printer off.

for three seconds to turn off the printer.

2 Press and hold down

, and then press and release

to turn the printer on.

until Language appears on the display, indicating that the printer has been reset.

3 Complete the initial printer setup.

Printhead errors

If the "Before you troubleshoot" checklist does not solve the problem, then try the following:

and · and · Troubleshooting

Page 89 of the Lexmark 10E user manual — R EMOVE AND REINSERT THE PRINTHEAD
Page 89 · click to enlarge
Page 89

R EMOVE AND REINSERT THE PRINTHEAD

1 Open the printer and lift the latch.

Lexmark 10E — R EMOVE AND REINSERT THE PRINTHEAD diagram (page 89)
Fig. 38

2 Remove the printhead.

Lexmark 10E — R EMOVE AND REINSERT THE PRINTHEAD diagram (page 89)
Fig. 39

3 Wipe the printhead contacts using a clean, lint-free cloth.

Lexmark 10E — R EMOVE AND REINSERT THE PRINTHEAD diagram (page 89)
Fig. 40

4 Reinsert the printhead.

Lexmark 10E — R EMOVE AND REINSERT THE PRINTHEAD diagram (page 89)
Fig. 41

Troubleshooting

Page 90 of the Lexmark 10E user manual — M AKE SURE THE PRINT JOB IS NOT PAUSED
Page 90 · click to enlarge
Page 90

Software did not install

If you encountered problems while installing, or if your printer does not appear in the list in the Printers folder or as a printer option when sending a print job, then try removing and reinstalling the software.

Before you reinstall the software, do the following:

MAKE SURE THAT YOUR COMPUTER MEETS THE MINIMUM SYSTEM REQUIREMENTS LISTED ON

THE PRINTER BOX

T EMPORARILY DISABLE SECURITY PROGRAMS IN W INDOWS BEFORE INSTALLING THE SOFTWARE

C HECK THE USB CONNECTION

1 Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.

2 Firmly plug the square end of the USB cable into the back of the printer.

3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.

The USB port is marked with a

USB symbol.

R ECONNECT THE PRINTER POWER SUPPLY

1 Turn off the printer, and then unplug the power cord from the wall outlet.

2 Gently remove the power supply from the printer, and then reinsert it.

3 Plug the power cord into the wall outlet, and then turn on the printer.

Print job does not print or is missing pages

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

M AKE SURE THE INK CARTRIDGES ARE INSERTED CORRECTLY

1 Turn the printer on, and then open the printer.

2 Make sure the cartridges are inserted correctly.

The cartridges should click firmly into the matching color slot of the printhead.

3 Close the printer.

SELECT YOUR PRINTER FROM THE PRINT DIALOG BEFORE SENDING THE PRINT JOB

M AKE SURE THE PRINT JOB IS NOT PAUSED

M AKE SURE YOUR PRINTER IS SET AS THE DEFAULT PRINTER

Troubleshooting

Page 91 of the Lexmark 10E user manual — Printer is busy or does not respond
Page 91 · click to enlarge
Page 91

R ECONNECT THE PRINTER POWER SUPPLY

1 Turn off the printer, and then unplug the power cord from the wall outlet.

2 Gently remove the power supply from the printer, and then reinsert it.

3 Plug the power cord into the wall outlet, and then turn on the printer.

R EMOVE AND RECONNECT THE USB CABLE CONNECTED TO YOUR PRINTER

C HECK THE USB CONNECTION

1 Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.

2 Firmly plug the square end of the USB cable into the back of the printer.

3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.

The USB port is marked with a

USB symbol.

R EMOVE AND REINSTALL THE PRINTER SOFTWARE

Printer is printing blank pages

Blank pages may be caused by improperly installed ink cartridges.

R EINSTALL THE INK CARTRIDGES AND DEEP CLEAN AND ALIGN THE PRINTHEAD

1 Reinstall the ink cartridges, see “Replacing ink cartridges” on page 12 for more information.

If the cartridges do not seem to fit, make sure the printhead is properly seated, and then try installing the cartridges again.

2 Load plain paper.

3 From the printer control panel, press

4 Press the arrow buttons to scroll to Maintenance, and then press

5 Press the arrow buttons to scroll to Deep Clean Printhead, and then press

A cleaning page prints.

6 Press the arrow buttons to scroll to Align Printer, and the press

An alignment page prints.

Printer is busy or does not respond

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

MAKE SURE THE PRINTER IS NOT IN POWER SAVER MODE

If the power light is blinking on and off slowly, then the printer is in Power Saver mode. Press

to wake up the printer.

Troubleshooting

Page 92 of the Lexmark 10E user manual — R EMOVE AND REINSTALL THE PRINTER SOFTWARE
Page 92 · click to enlarge
Page 92

If the printer will not come out of Power Saver mode, then reset the power:

1 Unplug the power cord from the wall outlet, and then wait 10 seconds.

2 Insert the power cord into the wall outlet, and then turn on the printer.

If this problem persists, then check our Web site for updates for your printer software or firmware.

R ECONNECT THE PRINTER POWER SUPPLY

1 Turn off the printer, and then unplug the power cord from the wall outlet.

2 Gently remove the power supply from the printer, and then reinsert it.

3 Plug the power cord into the wall outlet, and then turn on the printer.

Cannot delete documents from the print queue

If you have jobs stuck in the print queue and cannot delete them to get other jobs to print, then the computer and printer may not be communicating.

R ESTART THE COMPUTER AND TRY AGAIN

Cannot print through USB

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

C HECK THE USB CONNECTION

1 Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.

2 Firmly plug the square end of the USB cable into the back of the printer.

3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.

The USB port is marked with a

USB symbol.

M AKE SURE THE USB PORT IS ENABLED IN W INDOWS

, or click Start and then click Run.

2 In the Start Search or Run box, type devmgmt.msc.

3 Press Enter, or click OK.

The Device Manager opens.

4 Click the plus sign (+) beside Universal Serial Bus controllers.

If USB Host Controller and USB Root Hub are listed, then the USB port is enabled.

For more information, see the computer documentation.

R EMOVE AND REINSTALL THE PRINTER SOFTWARE

1 Click · Troubleshooting

Page 93 of the Lexmark 10E user manual — C HECK PAPER CONDITION
Page 93 · click to enlarge
Page 93

Jams and misfeeds troubleshooting

  • “Paper jam in the printer” on page 93
  • “Paper jam in the paper support” on page 93
  • “Paper or specialty media misfeeds” on page 93

Paper jam in the printer

to turn off the printer.

2 Check the paper tray or lift the scanner unit to check for jammed paper.

3 Firmly grasp the paper, and then gently pull it out.

to turn the printer back on.

Paper jam in the paper support

to turn off the printer.

2 Firmly grasp the paper, and then gently pull it out.

to turn the printer back on.

Paper or specialty media misfeeds

These are possible solutions if paper or specialty media misfeeds or skews, or if multiple sheets feed or stick together. Try one or more of the following:

C HECK PAPER CONDITION

Use only new, unwrinkled paper.

Show 5 more labels / short text on this page
1 Press · 4 Press · 1 Press · 3 Press · Troubleshooting
Page 94 of the Lexmark 10E user manual — For Macintosh users:
Page 94 · click to enlarge
Page 94

C HECK PAPER LOADING

  • Load a smaller amount of paper into the printer.
  • Load paper with the print side faceup. (If you are not sure which side is the printable side, see the instructions that came with the paper.)
  • Check the loading instructions for your paper or specialty media.

R EMOVE EACH PAGE AS IT IS PRINTED

A DJUST THE PAPER GUIDES TO FIT THE LOADED PAPER

Print troubleshooting

  • “Poor quality at the edges of the page” on page 94
  • “Streaks or lines on printed image” on page 95
  • “Print speed is slow” on page 95
  • “Computer slows down when printing” on page 96

Poor quality at the edges of the page

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

C HECK MINIMUM PRINT SETTINGS

Unless you are using the borderless feature, use these minimum print margin settings:

  • Left and right margins: – 6.35 mm (0.25 in.) for letter-size paper – 3.37 mm (0.133 in.) for all paper sizes except letter
  • Top margin: 1.7 mm (0.067 in.)
  • Bottom margin: 12.7 mm (0.5 in.)

S ELECT THE B ORDERLESS PRINT FEATURE

For Windows users:

1 With a document or photo open, click File Print.

2 Click Properties, Preferences, Options, or Setup.

3 From the Paper Options section of the Print Setup tab, select Borderless.

For Macintosh users:

1 With a document or photo open, choose File > Print.

2 From the Printer pop-up menu, choose the printer.

3 If necessary, click Advanced.

4 From the print options pop-up menu, choose Paper Handling.

Troubleshooting

Page 95 of the Lexmark 10E user manual — R EMOVE AND REINSTALL THE PRINTER SOFTWARE
Page 95 · click to enlarge
Page 95

5 From the Destination Paper Size section, select Scale to fit paper size.

6 From the Paper Size pop-up menu, choose a paper size that has “(Borderless)” in the name. For example, if you are printing on a 4 x 6 photo card, then choose US 4 x 6 in (Borderless).

Streaks or lines on printed image

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

C HECK THE INK LEVELS

Replace low or empty ink cartridges.

S ELECT A HIGHER PRINT QUALITY FROM THE PRINTER SOFTWARE

M AKE SURE THE INK CARTRIDGES ARE PROPERLY INSTALLED

A LIGN THE PRINTHEAD

C LEAN OR D EEP C LEAN THE PRINTHEAD NOZZLES

Print speed is slow

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

M AXIMIZE COMPUTER PROCESSING SPEED

  • Close all applications not in use.
  • Minimize the number and size of graphics and images in the document.
  • Remove as many unused fonts as possible from your system.

A DD MEMORY

Consider purchasing more RAM.

S ELECT A LOWER PRINT QUALITY FROM THE PRINTER SOFTWARE

MANUALLY SELECT A PAPER TYPE THAT MATCHES THE TYPE OF PAPER YOU ARE USING

R EMOVE AND REINSTALL THE PRINTER SOFTWARE

Troubleshooting

Page 96 of the Lexmark 10E user manual — C LEAN THE SCANNER GLASS
Page 96 · click to enlarge
Page 96

Computer slows down when printing

These are possible solutions. Try one of the following:

IF YOU ARE USING A USB CONNECTION, THEN TRY A DIFFERENT USB CABLE

IF YOU ARE ON A NETWORK, THEN RESET THE POWER OF THE ACCESS POINT (ROUTER)

1 Unplug the power cord from the access point.

2 Wait ten seconds, and then insert the power cord.

Copy and scan troubleshooting

  • “Copier or scanner does not respond” on page 96
  • “Scanner unit does not close” on page 96
  • “Poor copy or scanned image quality” on page 96
  • “Partial copies or scans of documents or photos” on page 97
  • “Scan was not successful” on page 97
  • “Scanning takes too long or freezes the computer” on page 97
  • “Cannot scan to a computer over a network” on page 97

Copier or scanner does not respond

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

S ET YOUR PRINTER AS THE DEFAULT PRINTER

R EMOVE AND REINSTALL THE PRINTER SOFTWARE

Scanner unit does not close

1 Lift the scanner unit.

2 Remove any obstruction keeping the scanner unit open.

3 Lower the scanner unit.

Poor copy or scanned image quality

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

C LEAN THE SCANNER GLASS

A DJUST THE SCAN QUALITY FROM THE PRINTER SOFTWARE

REVIEW THE TIPS FOR COPYING, SCANNING, AND IMPROVING PRINT QUALITY

Troubleshooting

Page 97 of the Lexmark 10E user manual — NETWORK
Page 97 · click to enlarge
Page 97

U SE A CLEARER VERSION OF THE ORIGINAL DOCUMENT OR IMAGE

MAKE SURE THE DOCUMENT OR PHOTO IS LOADED FACEDOWN ON THE SCANNER GLASS AND IN

THE CORRECT CORNER

Partial copies or scans of documents or photos

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

MAKE SURE THE DOCUMENT OR PHOTO IS LOADED FACEDOWN ON THE SCANNER GLASS AND IN

THE CORRECT CORNER

SELECT A PAPER SIZE FROM THE PRINTER SOFTWARE THAT MATCHES THE LOADED PAPER

MAKE SURE THE ORIGINAL SIZE SETTING MATCHES THE SIZE OF THE DOCUMENT YOU ARE SCANNING

Scan was not successful

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

C HECK THE USB CONNECTION

1 Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.

2 Firmly plug the square end of the USB cable into the back of the printer.

3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.

The USB port is marked with a

USB symbol.

R ESTART THE COMPUTER

Scanning takes too long or freezes the computer

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

C LOSE OTHER SOFTWARE PROGRAMS THAT ARE NOT BEING USED

U SE A LOWER SCANNING RESOLUTION

Cannot scan to a computer over a network

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

MAKE SURE THE PRINTER AND THE DESTINATION COMPUTER ARE CONNECTED TO THE SAME

NETWORK

Troubleshooting

Page 98 of the Lexmark 10E user manual — C HECK THE USB CONNECTION
Page 98 · click to enlarge
Page 98

M AKE SURE THE PRINTER SOFTWARE IS INSTALLED ON THE DESTINATION COMPUTER

Memory card troubleshooting

  • “Memory card troubleshooting checklist” on page 98
  • “Nothing happens when a memory card is inserted” on page 98
  • “Cannot print documents from a memory card or flash drive” on page 98
  • “Photos do not transfer from a memory card across a wireless network” on page 99

Memory card troubleshooting checklist

Before you troubleshoot, use the following checklist to solve most memory card problems:

  • Make sure that the memory card you are using can be used in the printer.
  • Make sure the memory card is not damaged.
  • Make sure memory card contains supported file types.

Nothing happens when a memory card is inserted

If the "Memory card troubleshooting checklist" does not solve the problem, then try one or more of the following:

R EINSERT THE MEMORY CARD

The memory card may have been inserted too slowly. Remove and then reinsert the memory card quickly.

C HECK THE USB CONNECTION

1 Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.

2 Firmly plug the square end of the USB cable into the back of the printer.

3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.

The USB port is marked with a

USB symbol.

C HECK THE NETWORK CONNECTION

If the printer and computer are connected over a network, then make sure that the correct host and device are communicating. Select the printer from the computer or the computer from the printer.

Cannot print documents from a memory card or flash drive

If the "Memory card troubleshooting checklist" does not solve the problem, then try the following:

C HECK THE USB CONNECTION

1 Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.

2 Firmly plug the square end of the USB cable into the back of the printer.

3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.

The USB port is marked with a

USB symbol.

Troubleshooting

Page 99 of the Lexmark 10E user manual — Wireless troubleshooting checklist
Page 99 · click to enlarge
Page 99

C HECK THE NETWORK CONNECTION

If the printer and computer are connected over a network, then make sure that the correct host and device are communicating. Select the printer from the computer or the computer from the printer.

Photos do not transfer from a memory card across a wireless network

If the "Memory card troubleshooting checklist" does not solve the problem, then try one or more of the following:

MAKE SURE THAT BOTH THE PRINTER AND THE DESTINATION COMPUTER ARE TURNED ON AND

READY

S ELECT THE CORRECT COMPUTER NAME FROM THE LIST ON THE PRINTER

M AKE SURE YOUR WIRELESS NETWORK IS CONNECTED AND ACTIVE

If your wireless connection is down, then use a USB cable to connect your printer to your computer.

Wireless troubleshooting

  • “Wireless troubleshooting checklist” on page 99
  • “Resetting the wireless settings to factory defaults” on page 100
  • “Cannot print over wireless network” on page 100
  • “The Continue button is unavailable” on page 104
  • “Cannot print and there is a firewall on the computer” on page 105
  • “Wi-Fi indicator light is not lit” on page 105
  • “Wi-Fi indicator light is green but the printer does not print (Windows only)” on page 106
  • “Wi-Fi indicator light is still orange” on page 107
  • “Wi-Fi indicator light is blinking orange during installation” on page 108
  • “Wireless print server not installed” on page 112
  • ““Communication not available” message displays when printing wirelessly” on page 112
  • “Communication with printer lost when connected to Virtual Private Network (VPN)” on page 114
  • “Resolving intermittent wireless communications issues” on page 115

Wireless troubleshooting checklist

Before beginning to troubleshoot the wireless printer, verify the following:

  • The printer, the computer, and the wireless access point are all plugged in and turned on.
  • The wireless network is working properly.

Try accessing other computers on your wireless network.

If your network has Internet access, try connecting to the Internet over a wireless connection.

Troubleshooting

Page 100 of the Lexmark 10E user manual — T URN THE WIRELESS ACCESS POINT OFF AND THEN BACK ON
Page 100 · click to enlarge
Page 100
  • Your SSID is correct.

Print a network setup page to verify the SSID the printer is using.

If you are not sure if your SSID is correct, then run the wireless setup again. • Your WEP key or WPA passphrase is correct (if your network is secure).

Log into the wireless access point (wireless router) and check the security settings.

A security key is like a password. All devices on the same wireless network using WEP, WPA, or WPA2 share the same security key.

If you are not sure if your security information is correct, run the wireless setup again. • The printer and the computer are within the range of the wireless network.

  • For most networks, the printer and the computer should be within 100 feet (30 meters) of the wireless access point (wireless router).
  • The Wi-Fi indicator light is lit and is solid green.
  • The printer driver is installed on the computer from which you are performing a task.
  • The correct printer port is selected.
  • The computer and printer are both connected to the same wireless network.
  • The printer is located away from obstacles or electronic devices that could interfere with the wireless signal.

Make sure the printer and wireless access point are not separated by poles, walls, or support columns containing metal or concrete.

Many devices can interfere with the wireless signal, including baby monitors, motors, cordless phones, security system cameras, other wireless networks, and some Bluetooth devices.

Resetting the wireless settings to factory defaults

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Network Setup, and then press

3 Press the arrow buttons to scroll to Reset Network Adapter to Factory Defaults, and then press

4 Press the arrow buttons to scroll to Yes, and then press

The printer wireless settings are reset to factory default settings. To verify, print a network setup page.

Cannot print over wireless network

If you encountered problems while installing, or if your printer does not appear in the printers folder or as a printer option when sending a print job, then you can try uninstalling and reinstalling the software.

Before you reinstall the software, check the troubleshooting checklist, and then do the following:

T URN THE WIRELESS ACCESS POINT OFF AND THEN BACK ON

Turning the access point off and then back on again can sometimes refresh network connections and resolve connectivity issues.

Troubleshooting

Page 101 of the Lexmark 10E user manual — M OVE YOUR ACCESS POINT AWAY FROM OTHER ELECTRONIC DEVICES
Page 101 · click to enlarge
Page 101

D ISCONNECT FROM VPN SESSION

When you are connected to another network through a VPN connection, you will not be able to access the printer over your wireless network. End your VPN session and try printing again.

M AKE SURE D EMO M ODE IS TURNED OFF

Check to see if your printer has a Demo Mode. Selected printer features are not available when Demo Mode is turned on.

From the printer control panel, navigate to Demo Mode:

> Demo Mode.

Select Off, and then save the setting.

C HECK YOUR WEP KEY OR WPA PASSPHRASE

If your wireless access point is using Wired Equivalent Privacy (WEP) security, then the WEP key should be:

  • Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.

or • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard. ASCII characters in a WEP key are case-sensitive.

If your wireless access point is using Wi-Fi Protected Access (WPA) security, then the WPA passphrase should be:

  • From 8 to 63 ASCII characters. ASCII characters in a WPA passphrase are case-sensitive.

or • Exactly 64 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.

CHECK IF YOUR WIRELESS ACCESS POINT HAS AN ASSOCIATION/REGISTRATION BUTTON

Wireless broadband boxes in Europe, the Middle East and Africa such as LiveBox, AliceBox, N9UF Box, FreeBox, or Club Internet may require you to press an association/registration button when adding the printer to your wireless network.

If you are using one of these boxes and need more information, see the documentation that came with your box, or contact your Internet Service Provider (ISP).

M OVE YOUR ACCESS POINT AWAY FROM OTHER ELECTRONIC DEVICES

There may be temporary interference from electronic devices such as microwave ovens or other appliances, cordless phones, baby monitors, and security system cameras. Make sure your access point is not positioned too closely to these devices.

MOVE THE COMPUTER AND/OR PRINTER CLOSER TO THE WIRELESS ROUTER

The range of your wireless network depends on many factors, including the abilities of your router and network adapters. If you are having trouble printing, try placing the computer and printer no more than 100 feet apart.

Troubleshooting

Page 102 of the Lexmark 10E user manual — For Windows users
Page 102 · click to enlarge
Page 102

C HECK THE WIRELESS SIGNAL QUALITY

Print the network setup page and check the signal quality. If the signal quality is listed as good or excellent, then another factor is causing the problem.

C HECK YOUR ADVANCED SECURITY SETTINGS

  • If you are using MAC (Media Access Control) address filtering to limit access to your wireless network, then you must add the printer MAC address to the list of addresses allowed to connect to the wireless access point.
  • If you set the wireless access point to issue a limited number of IP addresses, then you must change this so that the printer can be added.

MAKE SURE YOUR COMPUTER IS CONNECTED TO YOUR WIRELESS ACCESS POINT (WIRELESS

ROUTER )

  • See if you have access to the Internet by opening your Web browser and accessing any site.
  • If there are other computers or resources on your wireless network, then check to see if you can access them from your computer.

MAKE SURE THAT YOUR COMPUTER AND PRINTER ARE CONNECTED TO THE SAME WIRELESS

NETWORK

If the printer is not on the same wireless network as the computer, then you will not be able to print wirelessly. The SSID of the printer must match the SSID of the computer, if the computer is already connected to the wireless network.

For Windows users

1 Obtain the SSID of the network that the computer is connected to. a Type the IP address of your wireless access point (wireless router) into the address field of your Web browser.

If you do not know the IP address of the wireless access point:

  • , or click Start and then click Run . 2 In the Start Search or Run box, type cmd . 3 Press Enter or click OK . The Command Prompt window opens. 4 Type ipconfig , and then press Enter . Check the Wireless Network Connection section:
  • The “Default Gateway” entry is typically the wireless access point .
  • The IP address appears as four sets of numbers separated by periods, such as 192.168.2.134. b Type the user name and password of the router when prompted.

c Click OK. d On the main page, click Wireless or any other selection where settings are stored. The SSID will be displayed. e Write down the SSID.

1 Click · Troubleshooting

Page 103 of the Lexmark 10E user manual — For Macintosh users with a wireless access point
Page 103 · click to enlarge
Page 103

2 Print the printer network setup page.

In the Wireless section, look for SSID.

3 Compare the SSID of the computer and SSID of the printer.

If the SSIDs are the same, then the computer and the printer are connected to the same wireless network.

If the SSIDs are not the same, then run the utility again to set up the printer on the wireless network used by the computer.

For Macintosh users with an AirPort base station

In Mac OS X version 10.5

1 From the Apple menu, choose System Preferences.

2 Click Network.

3 Click AirPort.

The SSID of the network the computer is connected to is displayed in the Network Name pop-up menu.

4 Write down the SSID.

In Mac OS X version 10.4 and earlier

1 From the Finder desktop, choose Go > Applications.

2 From the Applications folder, double-click Internet Connect.

3 From the toolbar, click AirPort.

The SSID of the network the computer is connected to is displayed in the Network pop-up menu.

4 Write down the SSID.

For Macintosh users with a wireless access point

1 Type the IP address of the wireless access point in the address field of your Web browser, and then continue to step 2.

If you do not know the IP address of the wireless access point, then do the following:

a From the Apple menu, choose System Preferences. b Click Network.

c Click AirPort. d Click Advanced > TCP/IP or TCP/IP.

The “Router” entry is typically the wireless access point.

2 Type your user name and password when prompted.

3 Click OK.

4 On the main page, click Wireless or another selection where settings are stored. The SSID will be displayed.

5 Write down the SSID, security type and the WEP key/WPA passphrase (if shown).

  • Make sure you copy the network information down exactly, including any capital letters.
  • Store the SSID and the WEP key or WPA passphrase in a safe place for future reference.

Troubleshooting

Page 104 of the Lexmark 10E user manual — R ECONNECT THE POWER SUPPLY
Page 104 · click to enlarge
Page 104

MAKE SURE YOUR OS IS COMPATIBLE WITH WIRELESS PRINTING THROUGH AIRPORT

The printer only supports wireless printing through AirPort base stations for Mac OS X 10.5 or later.

The Continue button is unavailable

Try the following solutions in the order they appear until the Continue button becomes active and can be clicked:

CHECK IF THE USB CABLE IS SECURELY PLUGGED INTO THE USB PORTS ON BOTH THE

COMPUTER AND THE PRINTER

USB ports are marked with the

symbol.

M AKE SURE THAT THE PRINTER IS PLUGGED IN AND TURNED ON

Check to see if the

button is lit. If you have just turned on the printer, then you might need to disconnect the USB cable and reconnect it.

M AKE SURE THAT THE USB PORT ON THE COMPUTER IS WORKING

Test the USB port by connecting other devices to it. If you can successfully use other devices from the port, then the port is working.

If the USB port on the computer is not working, then try using the other USB ports on the computer.

M AKE SURE THAT THE USB CABLE IS WORKING

Try using a different USB cable. If you are using a cable longer than 10 feet, then try using a shorter cable.

MAKE SURE THAT YOU ARE USING THE CORRECT CD FOR YOUR PRINTER MODEL

Compare the printer model on the CD to the printer model on the printer. The numbers should either match exactly or be within the same series.

If you have any doubts, look for an updated version of the printer software on our Web site. For more information, see “Installing the printer software” in the User's Guide. You can access the User's Guide from the link at the bottom of the installation screen.

R ECONNECT THE POWER SUPPLY

1 Turn off the printer.

2 Unplug the power cord from the power outlet.

3 Remove the power supply from the back of the printer and then plug it back in.

4 Plug the power cord back into the power outlet.

5 Turn on the printer, and then resume the installation on your computer.

Troubleshooting

Page 105 of the Lexmark 10E user manual — Wi-Fi indicator light is not lit
Page 105 · click to enlarge
Page 105

T RY RUNNING THE INSTALLER AGAIN

1 Close the installer.

2 Remove the CD, and then restart the computer.

3 Insert the CD and then run the installer again.

  • When you get to the Software Already Installed screen, make sure you select Install a printer .
  • If you have already set up your printer, select Additional Computer when you get to the Setting up a new printer? screen to skip the hardware setup wizard.

CHECK THAT YOUR COMPUTER IS ABLE TO ACKNOWLEDGE USB ACTIVITY ON THE USB PORT

Open the Device Manager to check if it has activity whenever a USB device is connected to a USB port:

, or click Start and then click Run.

2 In the Start Search or Run box, type devmgmt.msc.

3 Press Enter, or click OK.

The Device Manager opens.

4 Watch the Device Manager window while connecting a USB cable or another device to the USB port. The window refreshes when Device Manager recognizes the USB connection.

  • If there is activity on Device Manager but none of the previous solutions worked, call Customer Support.
  • If there is no activity on Device Manager, there may be a problem with your computer and its USB support. The computer must recognize the USB connection in order for installation to work.

Cannot print and there is a firewall on the computer

Third-party (non-Microsoft) firewalls can interfere with wireless printing. If the printer and computer are configured correctly, and the wireless network is working, but the printer will not print wirelessly, then a firewall could be the problem. If there is a firewall (other than the Windows firewall) on the computer, try one or more of the following:

  • Update the firewall using the most recent update available from the manufacturer. Refer to the documentation that came with your firewall for instructions on how to do this.
  • If programs request firewall access when you install the printer or try to print, make sure you allow those programs to run.
  • Temporarily disable the firewall and install the wireless printer on the computer. Re-enable the firewall when you have completed the wireless installation.

Wi-Fi indicator light is not lit

C HECK POWER

If the Wi-Fi indictor light is off, make sure the

  • light is not on, check the following:
  • Make sure the printer is plugged in and turned on.
  • Make sure the printer is plugged into a working outlet.
  • If the printer is plugged into a power strip, make sure it is turned on and working.

light is on. If the

1 Click · Troubleshooting

Page 106 of the Lexmark 10E user manual — S ELECT THE WIRELESS PORT
Page 106 · click to enlarge
Page 106

Wi-Fi indicator light is green but the printer does not print (Windows only)

If you have completed the configuration for wireless printing and all of the settings appear to be correct, but the printer does not print, then try one or more of the following:

A LLOW THE WIRELESS INSTALLATION TO COMPLETE

Do not attempt to print, remove the installation CD, or detach the installation cable until you see the Wireless Setup Successful screen.

E NABLE THE PRINTER

Confirm that the printer is enabled:

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.

3 Press Enter, or click OK.

The printer folder opens.

4 Right-click the new printer; from the menu, select Use Printer Online.

5 Close the Printers or Printers and Faxes window and try printing again.

S ELECT THE WIRELESS PRINTER

You may need to select the wireless printer from your computer to use the printer wirelessly.

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.

3 Press Enter, or click OK.

The printer folder opens.

4 Right-click the printer in the folder with the matching name and model number followed by ”(Network).”

5 Select Use Printer Online from the menu.

6 Close the Printers or Printers and Faxes window and try printing again.

S ELECT THE WIRELESS PORT

If you have previously set up your printer as a locally attached printer, then you may need to select the wireless printer to use the printer wirelessly.

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.

3 Press Enter, or click OK.

The printer folder opens.

4 Right-click the printer, and then select Properties from the menu.

Show 4 more labels / short text on this page
1 Click · 1 Click · 1 Click · Troubleshooting
Page 107 of the Lexmark 10E user manual — If you are using WPA security
Page 107 · click to enlarge
Page 107

5 Click the Ports tab.

6 Locate the selected port. The selected port has a check beside it in the Port column.

7 If the Description column of the selected port indicates that it is a USB port, scroll through the list and select the port with Printer Port in the Description column. Check the printer model in the Printer column to make sure you select the right printer port.

8 Click OK, and then try to print again.

Wi-Fi indicator light is still orange

When the Wi-Fi indicator light is orange, it may indicate that the printer is:

  • Not configured in infrastructure mode
  • Waiting to make an ad hoc connection to another wireless device
  • Not connected to a wireless network

The printer may be unable to join the network because of interference, its distance from the wireless access point (wireless router), or until its settings are changed.

These are possible solutions. Try one or more of the following:

C HECK NETWORK NAME

Make sure your network does not have the same name as another network near you. For example, if you and your neighbor both use a manufacturer's default network name, your printer could be connecting to your neighbor's network.

If you are not using a unique network name, consult the documentation for your wireless access point (wireless router) to learn how to set a network name.

If you set a new network name, you must reset the printer and computer SSID to the same network name.

C HECK SECURITY KEYS

If you are using WEP security

A valid WEP key is:

  • Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.

or • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard.

If you are using WPA security

A valid WPA passphrase is:

  • From 8 to 63 ASCII characters. ASCII characters in a WPA passphrase are case-sensitive.

or • Exactly 64 hexadecimal characters. Hexadecimal characters are A-F, a-f, and 0-9.

If your wireless network is not using security, then you will not have a security key. Using a wireless network with no security is not recommended because it can allow intruders to use your network resources without your consent.

Troubleshooting

Page 108 of the Lexmark 10E user manual — C HECK YOUR WEP KEY OR WPA PASSPHRASE
Page 108 · click to enlarge
Page 108

MOVE THE COMPUTER AND/OR PRINTER CLOSER TO THE WIRELESS ACCESS POINT (WIRELESS

ROUTER )

The possible distance between devices in 802.11b or 802.11g networks is 300 feet, while the wireless network range potentially doubles in 802.11n networks. The range of your wireless network depends on many factors, including the abilities of your router and network adapters. If you are having trouble printing, try placing the computer and printer no more than 100 feet apart.

You can find the strength of the network signal on the printer network setup page.

C HECK MAC ADDRESS

If your network uses MAC address filtering, make sure that you include the MAC address of the printer in the MAC address filter list. This will allow the printer to operate on the network.

Wi-Fi indicator light is blinking orange during installation

When the Wi-Fi indicator light is blinking orange, it indicates that the printer has been set up for wireless networking but cannot connect to the network for which it has been configured. The printer may be unable to join the network because of interference, its distance from the wireless access point (wireless router), or until its settings are changed.

These are possible solutions. Try one or more of the following:

M AKE SURE THE ACCESS POINT IS ON

Check the access point and, if necessary, turn it on.

M OVE YOUR ACCESS POINT TO MINIMIZE INTERFERENCE

There may be temporary interference from other devices such as microwave ovens or other appliances, cordless phones, baby monitors, and security system cameras. Make sure your access point is not positioned too closely to these devices.

MOVE THE COMPUTER AND/OR PRINTER CLOSER TO THE WIRELESS ACCESS POINT (WIRELESS

ROUTER )

The possible distance between devices in 802.11b or 802.11g networks is 300 feet, while the wireless network range potentially doubles in 802.11n networks. The range of your wireless network depends on many factors, including the abilities of your router and network adapters. If you are having trouble printing, try placing the computer and printer no more than 100 feet apart.

You can find the signal strength of the network on the network setup page.

C HECK YOUR WEP KEY OR WPA PASSPHRASE

A WEP key or WPA passphrase is like a password. All devices on a WEP-secured wireless network must share the same WEP key, and all devices on a WPA-secured wireless network must share the same WPA passphrase.

Troubleshooting

Page 109 of the Lexmark 10E user manual — For Windows users
Page 109 · click to enlarge
Page 109

If you are using WEP security

A valid WEP key is:

  • Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.

or • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard.

If you are using WPA security

A valid WPA passphrase is:

  • From 8 to 63 ASCII characters. ASCII characters in a WPA passphrase are case-sensitive.

or • Exactly 64 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.

If your wireless network is not using security, then you will not have a security key. Using a wireless network with no security is not recommended because it can allow intruders to use your network resources without your consent.

C HECK MAC ADDRESS

If your network uses MAC address filtering, make sure that you include the MAC address of the printer in the MAC address filter list. This will allow the printer to operate on the network. For more information, see “How do I find the MAC address?” on page 81.

P ING THE ACCESS POINT TO MAKE SURE THE NETWORK IS WORKING

For Windows users

1 If you do not already know it, find the IP address of the access point: a Click

, or click Start and then click Run. b In the Start Search or Run box, type cmd.

c Press Enter, or click OK.

The Command Prompt window opens. d Type ipconfig, and then press Enter.

  • The “Default Gateway” entry is typically the wireless access point.
  • The IP address appears as four sets of numbers separated by periods, such as 192.168.2.134.
2 Ping the access pointa Click

, or click Start and then click Run. b In the Start Search or Run box, type cmd.

c Press Enter, or click OK.

The Command Prompt window opens. d Type ping followed by a space and the IP address of the wireless access point. For example:

ping 192.168.1.100

e Press Enter.

Troubleshooting

Page 110 of the Lexmark 10E user manual — For Macintosh users
Page 110 · click to enlarge
Page 110
  • 3 Check to see whether the access point responds:
  • If the access point responds, you will see several lines appear that start with “Reply from.” It is possible that the printer did not connect to the wireless network. Turn off and then restart the printer to try to connect again.
  • If the access point does not respond, it will take several seconds and then you will see “Request timed out.”

Try the following:

, or click Start and then click Run. b In the Start Search or Run box, type ncpa.cpl, and then press Enter.

c Press Enter or click OK. d Select the appropriate connection from the ones shown. e Right-click the connection, and then click Repair.

For Macintosh users

1 Make sure AirPort is turned on: a From the Apple menu, choose System Preferences. b Click Network.

The AirPort status indicator should be green.

  • Yellow means the port is active but not connected.
  • Red means the port has not been configured.

2 Obtain the IP address of the wireless access point: a From the Apple menu, choose About This Mac. b Click More Info.

c From the Contents pane, choose Network. d From the Active Services list, choose AirPort.

The bottom pane lists the details of the AirPort connection. e Write down the “Router” entry. This is typically the wireless access point.

3 Ping the wireless access point: a From the Finder desktop, choose Go > Utilities. b Double-click Network Utility.

c Click the Ping tab. d In the network address field, typethe IP address of the wireless access point (or router). For example:

10.168.1.101

e Click Ping.

4 If the wireless access point responds, you will see several lines that display the number of bytes received from the wireless access point. This ensures that your computer is connected to the wireless access point.

If the wireless access point does not respond, then nothing is displayed. You can use Network Diagnostics to help resolve the problem.

a Click · Troubleshooting

Page 111 of the Lexmark 10E user manual — C ONFIGURE THE PRINTER FOR WIRELESS ACCESS AGAIN
Page 111 · click to enlarge
Page 111

M AKE SURE YOUR COMPUTER CAN COMMUNICATE WITH THE PRINTER

For Windows users

1 Obtain the printer IP address by printing a network setup page.

, or click Start and then click Run.

3 In the Start Search or Run box, type cmd.

4 Press Enter, or click OK.

The Command Prompt window opens.

5 Type ping followed by a space and the IP address of the printer. For example:

ping 192.168.1.100

6 Press Enter.

7 If the printer responds, you will see several lines that display the number of bytes received from the printer. This ensures that your computer is communicating with your printer.

If the printer does not respond, then “Request timed out” displays.

  • Your computer might not be connected to the network.
  • You may need to change the settings of your printer. Run the Wireless Setup Utility again.

For Macintosh users

1 Obtain the printer IP address by printing a network setup page.

In the TCP/IP section, look for Address.

2 From the Finder desktop, choose Go > Utilities.

3 Double-click Network Utility.

4 Click the Ping tab.

5 Type the IP address of the printer in the network address field. For example:

10.168.1.101

6 Click Ping.

7 If the printer responds, you will see several lines that display the number of bytes received from the printer. This ensures that your computer is communicating with your printer.

If the printer does not respond, then nothing is displayed.

  • Your computer might not be connected to the network. You can use Network Diagnostics to help resolve the problem.
  • You may need to change the settings of your printer. Run the Wireless Setup Assistant again.

C ONFIGURE THE PRINTER FOR WIRELESS ACCESS AGAIN

If your wireless settings have changed, you must run the printer wireless setup again. Some reasons your settings may have changed include your having manually changed your WEP or WPA keys, channel, or other network settings; or the access point having been reset to factory defaults.

Running the wireless setup again can also resolve issues due to misconfigurations that occurred when configuring the printer for wireless access.

2 Click · Troubleshooting

Page 112 of the Lexmark 10E user manual — “Communication not available” message displays when printing wirelessly
Page 112 · click to enlarge
Page 112
  • If you change network settings, change them on all the network devices before changing them for the access point.
  • If you have already changed the wireless network settings on your access point, then you must change the settings on all the other network devices before you can see them on the network.

For Windows users

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.

3 Select Printer Home.

4 Click the Settings tab.

5 Click the Wireless setup utility link.

6 Follow the instructions on the computer screen.

For Macintosh users

1 From the Finder desktop, double-click the printer folder.

2 Double-click Wireless Setup Assistant.

3 Follow the instructions on the computer screen.

Wireless print server not installed

You may see a message during installation indicating that the printer does not have a wireless print server installed. If you are sure the printer is capable of wireless printing, try the following:

C HECK POWER

light is on.

“Communication not available” message displays when printing wirelessly

These are possible solutions. Try one or more of the following:

MAKE SURE YOUR COMPUTER AND PRINTER HAVE VALID IP ADDRESSES FOR THE NETWORK

If you are using a laptop and have power saving settings enabled, you may see the ”Communication not available” message on your computer screen when you attempt to print wirelessly. This can occur if the laptop hard drive has powered down.

If you see this message, wait a few seconds and then try to print again. The laptop and printer require a few seconds to power up again and reattach to the wireless network.

If you see this message again after you have waited long enough for the printer and the laptop to attach to the network, there may be a problem with your wireless network.

1 Click · Make sure the · Troubleshooting

Page 113 of the Lexmark 10E user manual — M AKE SURE THE WIRELESS PORT IS SELECTED
Page 113 · click to enlarge
Page 113

Make sure that the laptop and printer have both received IP addresses:

For Windows users

, or click Start and then click Run.

2 In the Start Search or Run box, type cmd.

3 Press Enter, or click OK.

The Command Prompt window opens.

4 Type ipconfig, and then press Enter.

The IP address appears as four sets of numbers separated by periods, such as 192.168.0.100.

For Macintosh users

1 From the Apple menu, choose About This Mac.

2 Click More Info.

3 From the Contents pane, choose Network.

4 If you are connected over a wireless network, choose AirPort from the Active Services list.

How to locate a printer IP address

  • You can locate the printer IP address by viewing the printer network setup page.

If the printer and/or the laptop does not have an IP address, or if either has an address of 169.254.x.y (where x and y are any two numbers between 0 and 255):

1 Turn off the device that does not have a valid IP address (the laptop, the printer, or both).

2 Turn on the device(s).

3 Check the IP addresses again.

If the laptop and/or printer still does not receive a valid IP address, there is a problem with your wireless network. Try the following:

  • Make sure your wireless access point (wireless router) is turned on and is working.
  • Remove any objects that could be blocking the signal.
  • Temporarily turn off any unnecessary wireless devices on your network and pause any network-intensive activities, like large file transfers or network games. If the network is too busy, it is possible that the printer is not receiving the IP address within the allowed time.
  • Make sure your DHCP server, which may also be your wireless router, is working and is configured to assign IP addresses. If you are not sure how to do this, refer to the manual that came with your wireless router for more information.

If the printer and computer have valid IP addresses and the network is operation correctly, continue troubleshooting.

M AKE SURE THE WIRELESS PORT IS SELECTED

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.

1 Click · 1 Click · Troubleshooting

Page 114 of the Lexmark 10E user manual — Communication with printer lost when connected to Virtual Private Network (VPN)
Page 114 · click to enlarge
Page 114

3 Press Enter, or click OK.

The printer folder opens.

4 Right-click the printer, and then select Properties from the menu.

5 Click the Ports tab.

6 Locate the selected port. The selected port has a check beside it in the Port column.

7 If the Description column of the selected port indicates that it is a USB port, scroll through the list and select the port with Printer Port in the Description column. Check the printer model in the Printer column to make sure you select the right printer port.

8 Click OK, and then try to print again.

M AKE SURE BIDIRECTIONAL COMMUNICATION IS ENABLED

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.

3 Press Enter, or click OK.

The printer folder opens.

4 Right-click the printer, and then select Properties from the menu.

5 Click the Ports tab.

6 Click the box next to Enable bidirectional support if it is not already checked.

7 Click Apply.

8 Click OK, and then try to print again.

Communication with printer lost when connected to Virtual Private Network (VPN)

You will lose your connection to a wireless printer on your local network when connected to most Virtual Private Networks (VPNs). Most VPNs allow users to communicate with only the VPN and no other network at the same time. If you would like to have the ability to connect to your local network and to a VPN at the same time, the system support person for the VPN must enable split tunneling. Be aware that some organizations will not allow split tunneling due to security or technical concerns.

1 Click · Troubleshooting

Page 115 of the Lexmark 10E user manual — C HANGE THE CHANNEL THE WIRELESS ROUTER USES
Page 115 · click to enlarge
Page 115

Resolving intermittent wireless communications issues

You may notice that your printer works for a short time and then stops working, although apparently nothing has changed on your wireless network.

Many different issues can interrupt network communications, and sometimes more than one problem exists at the same time. These are possible solutions. Try one or more of the following:

DISCONNECT FROM ALL VPNS WHEN ATTEMPTING TO USE THE WIRELESS NETWORK

Most Virtual Private Networks (VPNs) allow computers to communicate with only the VPN and no other network at the same time. Disconnect from the VPN before installing the driver on the computer or before running the wireless setup on the computer.

To check if the computer is currently connected to a VPN, open your VPN Client software and check your VPN connections. If you do not have a VPN Client software installed, check the connections manually using the Windows VPN Client.

If you would like to have the ability to connect to your local network and to a VPN at the same time, the system support person for the VPN must enable split tunneling. Be aware that some organizations will not allow split tunneling due to security or technical concerns.

TURN OFF THE WIRELESS ACCESS POINT (WIRELESS ROUTER) AND TURN IT BACK ON AGAIN

E LIMINATE NETWORK CONGESTION

If a wireless network is too busy, the computer and printer may have difficulty communicating with each other. Some causes of wireless network congestion can include:

  • Transferring large files across the network
  • Networked games
  • Peer-to-peer file swapping applications
  • Streaming video
  • Too many computers on the wireless network at once

E LIMINATE SOURCES OF INTERFERENCE

Common household items can potentially disrupt wireless network communications. Cordless phones (but not cellular phones), microwave ovens, baby monitors, almost any kitchen appliance, wireless surveillance equipment, nearby wireless networks, and any appliance containing a motor can disrupt wireless network communications.

Try turning on any potential sources of interference and see if it causes the problem. If it does, separate your wireless network from the device.

C HANGE THE CHANNEL THE WIRELESS ROUTER USES

You can sometimes eliminate interference from unknown sources by changing the channel your wireless router uses to broadcast. There are three distinct channels on a router. Check the documentation that came with your router to determine which three apply. Other channels are offered as options, but these overlap. If the router is configured to use the default settings, change the channel setting to use a different distinct channel. Refer to the manual that came with your wireless router if you are not sure how to change the channel.

Troubleshooting

Page 116 of the Lexmark 10E user manual — C HECK FOR KNOWN ISSUES WITH THE WIRELESS ROUTER
Page 116 · click to enlarge
Page 116

C ONFIGURE THE WIRELESS ROUTER WITH A UNIQUE SSID

Many wireless networks use the SSID that the router was originally configured by the manufacturer to use. Using the default SSID can cause problems when more than one network is operating in the same area with the same SSID. The printer or computer may attempt to attach to the wrong network, although it will appear to be trying to connect to the correct network.

To avoid this type of interference, change the SSID on your wireless router from the default. Refer to the manual that came with your router if you are not sure how to change the SSID.

A SSIGN STATIC IP ADDRESSES TO ALL DEVICES IN THE NETWORK

Most wireless networks use a DHCP server (dynamic host configuration protocol) built in to the wireless router to assign IP addresses to clients on the wireless network. DHCP addresses are assigned when they are needed, as when a new device is added to the wireless network or when it is powered on. Wireless devices must send a request to the router, and receive an IP address in response so they can function on the network. Because the router performs many other tasks besides assigning addresses, it sometimes does not respond quickly enough with an address. The requesting device sometimes gives up before it receives an address.

Try assigning static IP addresses to the devices in your network to resolve this issue. Static IP addresses cut down on the work your wireless router has to do. Refer to the manual that came with your router and your operating system documentation if you are not sure how to assign static IP addresses.

To assign a static IP address to the printer, do the following:

1 Complete the wireless setup, allowing the printer to receive a DHCP address from a DHCP server on the network.

2 Print a network setup page to see what IP address is currently assigned to the printer.

3 Open a Web browser and then type the printer IP address in the address field. Press Enter.

The printer Web page loads.

4 Click the Configuration link.

5 Click the TCP/IP link.

6 Click the Set Static IP Address link.

7 Type the IP address you want to assign to the printer in the IP Address field.

8 Click the Submit button.

The Submitting Selection message appears.

Confirm that the IP address is updated by typing the static IP address in the browser address field and checking to see if the printer Web page reloads.

C HECK FOR KNOWN ISSUES WITH THE WIRELESS ROUTER

Some wireless routers have documented defects that were identified and resolved by the manufacturers. Visit the company Web site of the router manufacturer. Check for firmware updates and other advice from the manufacturer. Check the manual that came with your wireless router if you are not sure how to reach the manufacturer Web site.

Troubleshooting

Page 117 of the Lexmark 10E user manual — P URCHASE A NEW ROUTER
Page 117 · click to enlarge
Page 117

C HECK FOR WIRELESS ADAPTER UPDATES

If you are having trouble printing from one particular computer, check the Web site of the manufacturer of the network adapter card in that computer. It is possible that there is an updated driver available that could resolve the issue.

C HANGE ALL NETWORK DEVICES TO THE SAME TYPE

While it is possible to successfully mix 802.11b, 802.11g, and 802.11n devices on the same wireless network, the faster devices will sometimes prevent the slower devices from communicating. Wireless devices are designed to wait for a gap in wireless network communications before attempting to send information. If newer, faster devices are constantly using the wireless network, then older, slower devices will not have a chance to send data.

Try only turning on the network devices of the same type and see if network communications improve. If this solves the problem, you may want to upgrade your older devices with newer network adapters.

P URCHASE A NEW ROUTER

If your router is several years old, it may not be fully compatible with the newer wireless devices on your network. Consider purchasing a newer router that is fully compliant with the 802.11 IEEE specifications.

Troubleshooting

Page 118 of the Lexmark 10E user manual — 101, 10E
Page 118 · click to enlarge
Page 118

Notices

Product information

Product name:

Machine type:

Model(s):

101, 10E

Edition notice

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.

References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.

For Lexmark technical support, visit support.lexmark.com.

For information on supplies and downloads, visit www.lexmark.com.

If you don't have access to the Internet, you can contact Lexmark by mail:

Lexmark International, Inc. Bldg 004-2/CSC 740 New Circle Road NW Lexington, KY 40550 USA

© 2009 Lexmark International, Inc.

All rights reserved.

Lexmark S300 Series · April 2009

Page 119 of the Lexmark 10E user manual — Federal Communications Commission (FCC) compliance
Page 119 · click to enlarge
Page 119

UNITED STATES GOVERNMENT RIGHTS

This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.

Trademarks

Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.

PerfectFinish is a trademark of Lexmark International, Inc.

All other trademarks are the property of their respective owners.

Licensing notices

The following documents can be viewed from the installation software CD.

\Pubs FW_License.12.08.pdf

mDNS.tar.gz

\Install\Licenses Expat.txt

Inst_lib.txt Instgui.txt

Instgui.zip

Federal Communications Commission (FCC) compliance

information statement

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult your point of purchase or service representative for additional suggestions.

Directory File

Page 120 of the Lexmark 10E user manual — Noise emission levels
Page 120 · click to enlarge
Page 120

The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.

Any questions regarding this compliance information statement should be directed to:

Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232–3000

Hinweis zum GS-Zeichen

Postanschrift Lexmark Deutschland GmbH

Postfach 1560 63115 Dietzenbach

Addresse Lexmark Deutschland GmbH Max-Planck-Straße 12 63128 Dietzenbach

Telefon 0180 - 564 56 44 (Produktinformationen)

Telefon 01805- 51 25 11 (Technischer Kundendienst)

E-mail [email protected]

Noise emission levels

The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.

1-meter average sound pressure, dBA

Values are subject to change. See www.lexmark.com for current values.

Show 6 more labels / short text on this page
Modell 101, 10E · Gerätetyp 4443 · Printing 50 dBA · Scanning 35 dBA · Copying 47 dBA · Ready inaudible
Page 121 of the Lexmark 10E user manual — ENERGY STAR
Page 121 · click to enlarge
Page 121

Temperature information

Ambient temperature 15–32° C (60–90° F)

Shipping temperature -40–60° C (-40–140° F)

Storage temperature 1–60° C (34–140° F)

Waste from Electrical and Electronic Equipment (WEEE) directive

Lexmark 10E — Waste from Electrical and Electronic Equipment (WEEE) directive diagram (page 121)
Fig. 42 · Waste from Electrical and Electronic Equipment (WEEE…

The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products. If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.

Product disposal

Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.

Battery notice

This product contains Perchlorate material. Special handling may apply. For more information, go to http://www.dtsc.ca.gov/hazardouswaste/perchlorate/.

ENERGY STAR

Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.

Lexmark 10E — ENERGY STAR diagram (page 121)
Fig. 43
Page 122 of the Lexmark 10E user manual — Total energy usage
Page 122 · click to enlarge
Page 122

Power consumption

Product power consumption

The following table documents the power consumption characteristics of the product.

Mode Description Power consumption (Watts)

Printing The product is generating hard-copy output from electronic inputs. 17.01

Copying The product is generating hard-copy output from hard-copy original documents.

Scanning The product is scanning hard-copy documents. 9.37

Ready The product is waiting for a print job. 6.95

Power Saver The product is in energy-saving mode. 3.33

Off The product is plugged into a wall outlet, but the power switch is turned off.

The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.

Values are subject to change. See www.lexmark.com for current values.

Power Saver

This product is designed with an energy-saving mode called Power Saver. The Power Saver Mode is equivalent to the Sleep Mode. The Power Saver Mode saves energy by lowering power consumption during extended periods of inactivity. The Power Saver Mode is automatically engaged after this product is not used for a specified period of time, called the Power Saver Timeout.

Factory default Power Saver Timeout for this product (in minutes): 10

By using the configuration menus, the Power Saver Timeout can be modified between 1 minute and 240 minutes. Setting the Power Saver Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Power Saver Timeout to a high value maintains a fast response, but uses more energy.

Off mode

If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the wall outlet.

Total energy usage

It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.

Page 123 of the Lexmark 10E user manual — Notice to users of the US telephone network: FCC requirements
Page 123 · click to enlarge
Page 123

European Community (EC) directives conformity

This product is in conformity with the protection requirements of EC Council directives 2004/108/EC and 2006/95/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits.

A declaration of conformity with the requirements of the directives has been signed by the Director of Manufacturing and Technical Support, Lexmark International, Inc., S.A., Boigny, France.

This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.

Industry Canada compliance statement

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.

Avis de conformité aux normes de l’industrie du Canada

Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.

Regulatory notices for telecommunication terminal equipment

This section contains regulatory information pertaining to products that contain telecommunication terminal equipment such as facsimile.

Notice to users of the US telephone network: FCC requirements

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachments (ACTA). On the back of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to your telephone company.

This equipment uses the RJ-11C Universal Service Order Code (USOC) jack.

A plug and jack used to connect this equipment to the premises’ wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See your setup documentation for more information.

The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact your local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (for example, 03 is a REN of 0.3). For earlier products, the REN is shown separately on the label.

Page 124 of the Lexmark 10E user manual — Notice to users of the Canadian telephone network
Page 124 · click to enlarge
Page 124

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. You will also be advised of your right to file a complaint with the FCC.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

If you experience trouble with this equipment, for repair or warranty information, contact Lexmark International, Inc. at www.lexmark.com or your Lexmark representative. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

This equipment contains no user serviceable parts. For repair and warranty information, contact Lexmark International, Inc. See the previous paragraph for contact information.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information.

If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. It is recommended that the customer install an appropriate AC surge arrestor in the AC outlet to which this device is connected. An appropriate AC surge arrestor is defined as one that is suitably rated, and certified by UL (Underwriter's Laboratories), another NRTL (Nationally Recognized Testing Laboratory), or a recognized safety certification body in the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges.

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless said message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)

See your user documentation in order to program this information into your fax machine.

South Africa telecommunications notice

This modem must be used in conjunction with an approved surge protection device when connected to the PSTN.

Notice to users of the Canadian telephone network

This product meets the applicable Industry Canada technical specifications. The Ringer Equivalence Number (REN) is an indication of the maximum number of terminals allowed to be connected to a telephone interface. The terminus of an interface may consist of any combination of devices, subject only to the requirement that the sum of the RENs of all the devices does not exceed five. The modem REN is located on the rear of the equipment on the product labeling.

Page 125 of the Lexmark 10E user manual — Notice to users of the New Zealand telephone network
Page 125 · click to enlarge
Page 125

Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. It is recommended that the customer install an appropriate AC surge arrestor in the AC outlet to which this device is connected. An appropriate AC surge arrestor is defined as one that is suitably rated, and certified by UL (Underwriter’s Laboratories), another NRTL (Nationally Recognized Testing Laboratory), or a recognized safety certification body in the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges.

This equipment uses CA11A telephone jacks.

Avis réservé aux utilisateurs du réseau téléphonique du Canada

Ce produit est conforme aux spécifications techniques d’Industrie Canada. Le numéro REN (ringer equivalence number : numéro d’équivalence de sonnerie) fournit une indication du nombre maximum de terminaux pouvant être connectés à l’interface téléphonique. En bout de ligne, le nombre d’appareils qui peuvent être connectés n’est pas directement limité, mais la somme des REN de ces appareils ne doit pas dépasser cinq. Le numéro REN du modem est indiqué sur l’étiquette produit située à l’arrière de l’équipement.

Les compagnies de téléphone constatent que les surtensions électriques, en particulier celles dues à la foudre, entraînent d'importants dégâts sur les terminaux privés connectés à des sources d’alimentation CA. Il s’agit-là d’un problème majeur d’échelle nationale. En conséquence, il vous est recommandé de brancher un parasurtenseur dans la prise de courant à laquelle l’équipement est connecté. Utilisez un parasurtenseur répondant à des caractéristiques nominales satisfaisantes et certifié par le laboratoire d’assureurs UL (Underwriter’s Laboratories), un autre laboratoire agréé de type NRTL (Nationally Recognized Testing Laboratory) ou un organisme de certification agréé dans votre région ou pays. Ceci prévient tout endommagement de l’équipement causé par les orages et autres surtensions électriques.

Cet équipement utilise des prises de téléphone CA11A.

Notice to users of the New Zealand telephone network

The following are special conditions for the Facsimile User Instructions. The grant of a telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.

This equipment shall not be set up to make automatic calls to the Telecom's 111 Emergency Service.

This equipment may not provide for the effective hand-over of a call to another device connected to the same line.

This equipment should not be used under any circumstances that may constitute a nuisance to other Telecom customers.

Some parameters required for compliance with Telecom's telepermit requirements are dependent on the equipment associated with this device. The associated equipment shall be set to operate within the following limits for compliance to Telecom's specifications:

  • There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, and
  • The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next call attempt.
Page 126 of the Lexmark 10E user manual — Notice to Users in the European Union
Page 126 · click to enlarge
Page 126
  • The equipment shall be set to ensure that automatic calls to different numbers are spaced such that there is not less than 5 seconds between the end of one call attempt and the beginning of another.

Using this product in Switzerland

This product requires a Swiss billing tone filter (Lexmark part number 14B5109 or 80D1877) to be installed on any line which receives metering pulses in Switzerland. The Lexmark filter must be used, as metering pulses are present on all analog telephone lines in Switzerland.

Utilisation de ce produit en Suisse

Cet appareil nécessite l’utilisation d’un filtre de tonalité de facturation suisse (nº de référence Lexmark : 14B5109 ou 80D1877) devant être installé sur toute ligne recevant des impulsions de comptage en Suisse. Ce filtre doit être utilisé pour toute installation car ces impulsions existent sur toutes les lignes téléphoniques suisses.

Verwendung dieses Produkts in der Schweiz

Für dieses Produkt muss ein schweizerischer Billing Tone Filter zur Zählzeichenübertragung (Lexmark Teilenummer 14B5109 oder 80D1877) für jede Leitung installiert werden, über die in der Schweiz Zeitsteuertakte übertragen werden. Die Verwendung des Lexmark Filters ist obligatorisch, da in allen analogen Telefonleitungen in der Schweiz Zeitsteuertakte vorhanden sind.

Uso del prodotto in Svizzera

Questo prodotto richiede un filtro toni Billing svizzero, (codice Lexmark 14B5109 o 80D1877) da installare su tutte le linee che ricevono impulsi remoti in Svizzera. È necessario utilizzare il filtro Lexmark poiché gli impulsi remoti sono presenti su tutte le linee analogiche in Svizzera.

Notice to Users in the European Union

Products bearing the CE mark are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment.

Compliance is indicated by the CE marking.

A declaration of conformity with the requirements of the directives is available from the Director of Manufacturing and Technical Support, Lexmark International, S. A., Boigny, France.

Refer to the table at the end of the Notices section for further compliance information.

Page 127 of the Lexmark 10E user manual — Industry Canada (Canada)
Page 127 · click to enlarge
Page 127

Regulatory notices for wireless products

This section contains the following regulatory information pertaining to wireless products that contain transmitters, for example, but not limited to, wireless network cards or proximity card readers.

Exposure to radio frequency radiation

The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.

Notice to users in Brazil

Este equipamento opera em carater secundario, isto e, nao tem direito a protecao contra interferencia prejudicial, mesmo de estacoes do mesmo tipo, e nao pode causar interferencia a sistemas operando em carater primario. (Res.ANATEL 282/2001).

Industry Canada (Canada)

This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.

The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb

The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.

Industry Canada (Canada)

Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes :

(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement.

Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada.

En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.

Page 128 of the Lexmark 10E user manual — Notice to users in the European Union
Page 128 · click to enlarge
Page 128

Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur et loin des fenêtres afin de garantir une protection optimale.

Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.

L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc-sc.gc.ca/rpb

Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme aux spécifications techniques d'Industry Canada.

Taiwan NCC RF notice statement

Lexmark 10E — Taiwan NCC RF notice statement diagram (page 128)
Fig. 44 · Taiwan NCC RF notice statement

Notice to users in the European Union

Products bearing the CE mark are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment.

Compliance is indicated by the CE marking.

A declaration of conformity with the requirements of the directives is available from the Director of Manufacturing and Technical Support, Lexmark International, S. A., Boigny, France. Refer to the table at the end of the Notices section for further compliance information.

Products equipped with 2.4GHz Wireless LAN option are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment.

Compliance is indicated by the CE marking.

Operation is allowed in all EU and EFTA countries, but is restricted to indoor use only.

Page 129 of the Lexmark 10E user manual — Taiwan NCC RF notice statement
Page 129 · click to enlarge
Page 129

A declaration of conformity with the requirements of the directives is available from the Director of Manufacturing and Technical Support, Lexmark International, S. A., Boigny, France. Refer to the table at the end of the Notices section for further compliance information.

Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.

Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.

Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.

Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.

Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.

Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.

Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.

Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de

essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.

Page 130 of the Lexmark 10E user manual — LEXMARK SOFTWARE LICENSE AGREEMENT
Page 130 · click to enlarge
Page 130

Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky príslušné ustanovenia smernice 1999/5/ES.

Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.

Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

LEXMARK SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENTS

PLEASE READ CAREFULLY BEFOREUSING THIS PRODUCT: BY USING THIS PRODUCT, YOU AGREE TO BE BOUND BY ALL THE TERMS AND CONDITIONS OF THIS SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENTS. IF YOU DO NOT AGREE WITH THE TERMS OF THIS SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENTS, PROMPTLY RETURN THE PRODUCT UNUSED AND REQUEST A REFUND OF THE AMOUNT YOU PAID. IF YOU ARE INSTALLING THIS PRODUCT FOR USE BY OTHER PARTIES, YOU AGREE TO INFORM THE USERS THAT USE OF THE PRODUCT INDICATES ACCEPTANCE OF THESE TERMS.

PRINTER LICENSE AGREEMENT

I agree that this patented printer is licensed for, and designed to work with only genuine Lexmark ink cartridges for the life of the patented printer. I agree to: (1) use only genuine Lexmark ink cartridges with this printer (except I may use replacement cartridges made by Lexmark but sold without single use terms as described in the below cartridge license agreement), and (2) pass this printer license/agreement to any subsequent user of this printer.

CARTRIDGE LICENSE AGREEMENT*

I agree that the patented print cartridge(s) shipped with this printing device are sold subject to the following license/agreement: The patented print cartridge(s) contained inside is/are licensed for a single use only and is/are designed to stop working after delivering a fixed amount of ink. A variable amount of ink will remain in the cartridge when replacement is required. After this single use, the license to use the print cartridge terminates, and the used cartridge must be returned only to Lexmark for remanufacturing, refilling or recycling. If I buy another cartridge in the future that is sold subject to the above terms, I accept such terms as to that cartridge. If you do not accept the terms of this single use license/agreement; return this product in its original packaging to your point of purchase. A replacement cartridge sold without these terms is available at www.lexmark.com

LEXMARK SOFTWARE LICENSE AGREEMENT

This Software License Agreement (“License Agreement”) is a legal agreement between you (either an individual or a single entity) and Lexmark International, Inc. (“Lexmark”) that, to the extent your Lexmark product or Software Program is not otherwise subject to a written software license agreement between you and Lexmark or its suppliers, governs your use of any Software Program installed on or provided by Lexmark for use in connection with your Lexmark product. The term “Software Program” includes machine-readable instructions, audio/visual content (such as images and recordings), and associated media, printed materials and electronic documentation, whether incorporated into, distributed with or for use with your Lexmark product.

Page 131 of the Lexmark 10E user manual — LEXMARK SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENTS
Page 131 · click to enlarge
Page 131

1 STATEMENT OF SOFTWARE LIMITED WARRANTY. Lexmark warrants that the media (e.g., diskette or compact disk) on which the Software Program (if any) is furnished is free from defects in materials and workmanship under normal use during the warranty period. The warranty period is ninety (90) days and commences on the date the Software Program is delivered to the original end-user. This limited warranty applies only to Software Program media purchased new from Lexmark or an Authorized Lexmark Reseller or Distributor. Lexmark will replace the Software Program should it be determined that the media does not conform to this limited warranty. 2 DISCLAIMER AND LIMITATION OF WARRANTIES. EXCEPT AS PROVIDED IN THIS SOFTWARE LICENSE AGREEMENT AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, LEXMARK AND ITS SUPPLIERS PROVIDE THE SOFTWARE PROGRAM "AS IS" AND HEREBY DISCLAIM ALL OTHER WARRANTIES AND CONDITIONS, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, TITLE, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ABSENCE OF VIRUSES, ALL WITH REGARD TO THE SOFTWARE PROGRAM. TO THE EXTENT LEXMARK CANNOT BY LAW DISCLAIM ANY COMPONENT OF THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, LEXMARK LIMITS THE DURATION OF SUCH WARRANTIES TO THE 90-DAY TERM OF THE EXPRESS SOFTWARE LIMITED WARRANTY. This Agreement is to be read in conjunction with certain statutory provisions, as that may be in force from time to time, that imply warranties or conditions or impose obligations on Lexmark that cannot be excluded or modified. If any such provisions apply, then to the extent Lexmark is able, Lexmark hereby limits its liability for breach of those provisions to one of the following: providing you a replacement copy of the Software Program or reimbursement of the price paid for the Software Program.

The Software Program may include internet links to other software applications and/or internet web pages hosted and operated by third parties unaffiliated with Lexmark. You acknowledge and agree that Lexmark is not responsible in any way for the hosting, performance, operation, maintenance, or content of, such software applications and/or internet web pages. 3 LIMITATION OF REMEDY. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY AND ALL LIABILITY OF LEXMARK UNDER THIS SOFTWARE LICENSE AGREEMENT IS EXPRESSLY LIMITED TO THE GREATER OF THE PRICE PAID FOR THE SOFTWARE PROGRAM AND FIVE U.S. DOLLARS (OR THE EQUIVALENT IN LOCAL CURRENCY). YOUR SOLE REMEDY AGAINST LEXMARK IN ANY DISPUTE UNDER THIS SOFTWARE LICENSE AGREEMENT SHALL BE TO SEEK TO RECOVER ONE OF THESE AMOUNTS, UPON PAYMENT OF WHICH LEXMARK SHALL BE RELEASED AND DISCHARGED OF ALL FURTHER OBLIGATIONS AND LIABILITY TO YOU.

IN NO EVENT WILL LEXMARK, ITS SUPPLIERS, SUBSIDIARIES, OR RESELLERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, EXEMPLARY, PUNITIVE, OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LOST PROFITS OR REVENUES, LOST SAVINGS, INTERRUPTION OF USE OR ANY LOSS OF, INACCURACY IN, OR DAMAGE TO, DATA OR RECORDS, FOR CLAIMS OF THIRD PARTIES, OR DAMAGE TO REAL OR TANGIBLE PROPERTY, FOR LOSS OF PRIVACY ARISING OUT OR IN ANY WAY RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE PROGRAM, OR OTHERWISE IN CONNECTION WITH ANY PROVISION OF THIS SOFTWARE LICENCE AGREEMENT), REGARDLESS OF THE NATURE OF THE CLAIM, INCLUDING BUT NOT LIMITED TO BREACH OF WARRANTY OR CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY), AND EVEN IF LEXMARK, OR ITS SUPPLIERS, AFFILIATES, OR REMARKETERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY YOU BASED ON A THIRD-PARTY CLAIM, EXCEPT TO THE EXTENT THIS EXCLUSION OF DAMAGES IS DETERMINED LEGALLY INVALID. THE FOREGOING LIMITATIONS APPLY EVEN IF THE ABOVE-STATED REMEDIES FAIL OF THEIR ESSENTIAL PURPOSE. 4 U.S.A. STATE LAWS. This Software Limited Warranty gives you specific legal rights. You may also have other rights that vary from state to state. Some states do not allow limitations on how long an implied warranty lasts or the exclusion of limitation of incidental or consequential damages, so the above limitations may not apply to you.

Page 132 of the Lexmark 10E user manual — LEXMARK SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENTS
Page 132 · click to enlarge
Page 132

5 LICENSE GRANT. Lexmark grants you the following rights provided you comply with all terms and conditions of this License Agreement:

a Use. You may Use one (1) copy of the Software Program. The term “Use” means storing, loading, installing,

executing, or displaying the Software Program. If Lexmark has licensed the Software Program to you for concurrent use, you must limit the number of authorized users to the number specified in your agreement with Lexmark. You may not separate the components of the Software Program for use on more than one computer. You agree that you will not Use the Software Program, in whole or in part, in any manner that has the effect of overriding, modifying, eliminating, obscuring, altering or de-emphasizing the visual appearance of any trademark, trade name, trade dress or intellectual property notice that appears on any computer display screens normally generated by, or as a result of, the Software Program. b Copying. You may make one (1) copy of the Software Program solely for purposes of backup, archiving, or

installation, provided the copy contains all of the original Software Program’s proprietary notices. You may not copy the Software Program to any public or distributed network. c Reservation of Rights. The Software Program, including all fonts, is copyrighted and owned by Lexmark International, Inc. and/or its suppliers. Lexmark reserves all rights not expressly granted to you in this License Agreement. d Freeware. Notwithstanding the terms and conditions of this License Agreement, all or any portion of the

Software Program that constitutes software provided under public license by third parties (“Freeware”) is licensed to you subject to the terms and conditions of the software license agreement accompanying such Freeware, whether in the form of a discrete agreement, shrink-wrap license, or electronic license terms at the time of download. Use of the Freeware by you shall be governed entirely by the terms and conditions of such license. 6 TRANSFER. You may transfer the Software Program to another end-user. Any transfer must include all software components, media, printed materials, and this License Agreement and you may not retain copies of the Software Program or components thereof. The transfer may not be an indirect transfer, such as a consignment. Prior to the transfer, the end-user receiving the transferred Software Program must agree to all these License Agreement terms. Upon transfer of the Software Program, your license is automatically terminated. You may not rent, sublicense, or assign the Software Program except to the extent provided in this License Agreement, and any attempt to do so shall be void. 7 UPGRADES. To Use a Software Program identified as an upgrade, you must first be licensed to the original Software Program identified by Lexmark as eligible for the upgrade. After upgrading, you may no longer use the original Software Program that formed the basis for your upgrade eligibility. 8 LIMITATION ON REVERSE ENGINEERING. You may not alter, decrypt, reverse engineer, reverse assemble, reverse compile or otherwise translate the Software Program, except as and to the extent expressly permitted to do so by applicable law for the purposes of inter-operability, error correction, and security testing. If you have such statutory rights, you will notify Lexmark in writing of any intended reverse engineering, reverse assembly, or reverse compilation. You may not decrypt the Software Program unless necessary for the legitimate Use of the Software Program. 9 ADDITIONAL SOFTWARE. This License Agreement applies to updates or supplements to the original Software Program provided by Lexmark unless Lexmark provides other terms along with the update or supplement. 10 TERM. This License Agreement is effective unless terminated or rejected. You may reject or terminate this license at any time by destroying all copies of the Software Program, together with all modifications, documentation, and merged portions in any form, or as otherwise described herein. Lexmark may terminate your license upon notice if you fail to comply with any of the terms of this License Agreement. Upon such termination, you agree to destroy all copies of the Software Program together with all modifications, documentation, and merged portions in any form. 11 TAXES. You agree that you are responsible for payment of any taxes including, without limitation, any goods and services and personal property taxes, resulting from this Agreement or your Use of the Software Program.

Page 133 of the Lexmark 10E user manual — MICROSOFT CORPORATION NOTICES
Page 133 · click to enlarge
Page 133

12 LIMITATION ON ACTIONS. No action, regardless of form, arising out of this Agreement may be brought by either party more than two years after the cause of action has arisen, except as provided under applicable law. 13 APPLICABLE LAW. This Agreement is governed by the laws of the Commonwealth of Kentucky, United States of America. No choice of law rules in any jurisdiction shall apply. The UN Convention on Contracts for the International Sale of Goods shall not apply. 14 UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The Software Program has been developed entirely at private expense. Rights of the United States Government to use the Software Program is as set forth in this Agreement and as restricted in DFARS 252.227-7014 and in similar FAR provisions (or any equivalent agency regulation or contract clause). 15 CONSENT TO USE OF DATA. You agree that Lexmark, its affiliates, and agents may collect and use information you provide in relation to support services performed with respect to the Software Program and requested by you. Lexmark agrees not to use this information in a form that personally identifies you except to the extent necessary to provide such services. 16 EXPORT RESTRICTIONS. You may not (a) acquire, ship, transfer, or reexport, directly or indirectly, the Software Program or any direct product therefrom, in violation of any applicable export laws or (b) permit the Software Program to be used for any purpose prohibited by such export laws, including, without limitation, nuclear, chemical, or biological weapons proliferation. 17 AGREEMENT TO CONTRACT ELECTRONICALLY. You and Lexmark agree to form this License Agreement electronically. This means that when you click the “Agree” or “Yes” button on this page or use this product, you acknowledge your agreement to these License Agreement terms and conditions and that you are doing so with the intent to “sign” a contract with Lexmark. 18 CAPACITY AND AUTHORITY TO CONTRACT. You represent that you are of the legal age of majority in the place you sign this License Agreement and, if applicable, you are duly authorized by your employer or principal to enter into this contract. 19 ENTIRE AGREEMENT. This License Agreement (including any addendum or amendment to this License Agreement that is included with the Software Program) is the entire agreement between you and Lexmark relating to the Software Program. Except as otherwise provided for herein, these terms and conditions supersede all prior or contemporaneous oral or written communications, proposals, and representations with respect to the Software Program or any other subject matter covered by this License Agreement (except to the extent such extraneous terms do not conflict with the terms of this License Agreement, any other written agreement signed by you and Lexmark relating to your Use of the Software Program). To the extent any Lexmark policies or programs for support services conflict with the terms of this License Agreement, the terms of this License Agreement shall control.

* Products within the XX90 Series (including but not limited to models Z2390, Z2490, X2690, X3690, and X4690) are not subject to the Cartridge License Agreement. This Cartridge License Agreement does not apply to cartridges included within the printer boxes of XX75 Series products (including but not limited to models X4975 and X7675). It applies to replacement cartridges that are sold subject to these terms and conditions, however. Replacement cartridges sold without these terms are available through www.lexmark.com

MICROSOFT CORPORATION NOTICES

1 This product may incorporate intellectual property owned by Microsoft Corporation. The terms and conditions upon which Microsoft is licensing such intellectual property may be found at http://go.microsoft.com/fwlink/?LinkId=52369 2 This product is based on Microsoft Print Schema technology. You may find the terms and conditions upon which Microsoft is licensing such intellectual property at http://go.microsoft.com/fwlink/?LinkId=83288.

Page 134 of the Lexmark 10E user manual — ADOBE SYSTEMS INCORPORATED NOTICE
Page 134 · click to enlarge
Page 134

ADOBE SYSTEMS INCORPORATED NOTICE

Contains Flash®, Flash® Lite™ and/or Reader® technology by Adobe Systems Incorporated

This Product contains Adobe® Flash® player software under license from Adobe Systems Incorporated, Copyright © 1995-2007 Adobe Macromedia Software LLC. All rights reserved. Adobe, Reader and Flash are trademarks of Adobe Systems Incorporated.

Page 136 of the Lexmark 10E user manual — Table of contents
Page 136 · click to enlarge
Page 136

Table of contents

Contentsp.2Safety informationp.5About your printerp.6Thank you for choosing this printer!p.6Minimizing your printer's environmental impactp.6Finding information about the printerp.7Understanding the parts of the printerp.9Ordering and replacing suppliesp.11Ordering ink cartridgesp.11Using genuine Lexmark ink cartridgesp.11Replacing ink cartridgesp.12Ordering paper and other suppliesp.13Recycling Lexmark productsp.13Using the printer control panel buttons and menusp.14Using the printer control panelp.14Changing temporary settings into new default settingsp.15Changing the Power Saver timeoutp.16Saving energy with Eco-Modep.17Resetting to factory settingsp.17Using the printer softwarep.19Minimum system requirementsp.19Using the Windows printer softwarep.19Using the Macintosh printer softwarep.21Finding and installing optional softwarep.22Updating the printer software (Windows only)p.23Reinstalling the printer softwarep.23Uninstalling the printer softwarep.23Installing the printer softwarep.24Loading paper and original documentsp.25Loading paperp.25Saving paper default settingsp.27Loading original documents on the scanner glassp.28Printingp.29Tips for printingp.29Printing basic documentsp.29Printing a documentp.29Collating printed copiesp.30Printing pages in reverse orderp.30Printing multiple pages on one sheetp.31Printing documents from a memory card or flash drive (Windows only)p.32Printing specialty documentsp.33Printing envelopesp.33Printing labelsp.33Printing on custom-size paperp.34Printing on both sides of the paper (duplexing) manuallyp.35Working with photosp.37Using a memory card or flash drive with the printerp.37Supported memory cards and file typesp.38Printing photos using the printer control panelp.38Printing photos from a memory device using the printer softwarep.39Printing photos from a PictBridge-enabled digital camerap.40Printing photos from a memory device using the proof sheetp.41Printing photos from a digital camera using DPOFp.42Printing from a Bluetooth-enabled devicep.42Setting up a connection between your printer and a Bluetooth-enabled devicep.42Setting the Bluetooth security levelp.43Printing from a Bluetooth-enabled devicep.44Managing print jobsp.45Setting your printer as the default printerp.45Changing the printing modep.45Pausing print jobsp.46Resuming print jobsp.47Canceling print jobsp.47Copyingp.49Tips for copyingp.49Making copiesp.49Copying photosp.49Enlarging or reducing imagesp.50Adjusting copy qualityp.50Making a copy lighter or darkerp.50Collating copies using the printer control panelp.51Repeating an image on one pagep.51Copying multiple pages on one sheetp.52Making a duplex copy manuallyp.52Canceling copy jobsp.53Scanningp.54Tips for scanningp.54Scanning to a local or network computerp.54Scanning to a flash drive or memory cardp.55Scanning photos into an editing applicationp.55Scanning documents into an editing applicationp.57Scanning directly to e-mail using the printer softwarep.57Scanning to a PDFp.58Scanning FAQp.59How can I improve the quality of a scan?p.59How do I scan in black and white?p.59Why am I being asked for a PIN?p.59What is an application list, and how do I update it?p.59Canceling scan jobsp.60Networkingp.61Installing the printer on a wireless networkp.61Wireless network compatibilityp.61Supported network security optionsp.61Printing a network setup pagep.62Information you will need to set up the printer on a wireless networkp.62Installing the printer on a wireless networkp.63Installing the printer on other computersp.63Interpreting the colors of the Wi-Fi indicator lightp.64Special wireless installation instructionsp.64Assigning a static IP addressp.65Changing wireless settings after installationp.65Advanced wireless setupp.66Creating an ad hoc wireless networkp.66Adding a printer to an existing ad hoc wireless networkp.69Configuring the printer wirelessly using WPS (Wi-Fi Protected Setup)p.69Switching between USB and wireless connections (Windows only)p.70Switching between USB and wireless connections (Macintosh only)p.70Sharing a printer in a Windows environmentp.71Sharing a printer in a Macintosh environmentp.72Networking FAQp.73What is Wi-Fi Protected Setup?p.73Where do I find my WEP key or WPA passphrase?p.73What is an SSID?p.73Where do I find my SSID?p.74What is a network?p.74How do I find out what type of security my network is using?p.74How are home networks configured?p.74Why do I need an installation cable?p.76How do I attach the installation cable?p.76How are infrastructure and ad hoc networks different?p.77Finding the signal strengthp.78How can I improve wireless signal strength?p.78How can I make sure my computer and printer are connected to the same wireless network?p.79Can I use my printer on a USB and a network connection at the same time?p.81What is a MAC address?p.81How do I find the MAC address?p.81What is an IP address?p.82What is TCP/IP?p.82How do I locate IP addresses?p.82How are IP addresses assigned?p.83What is a key index?p.83Maintaining the printerp.84Maintaining ink cartridgesp.84Checking ink levelsp.84Aligning the printheadp.84Cleaning the printhead nozzlesp.85Cleaning the exterior of the printerp.86Cleaning the scanner glassp.86Troubleshootingp.87Before you troubleshootp.87Using the Service Center to solve printer problemsp.87If Troubleshooting does not solve your problemp.87Setup troubleshootingp.87Incorrect language appears on the displayp.88Printhead errorsp.88Software did not installp.90Print job does not print or is missing pagesp.90Printer is printing blank pagesp.91Printer is busy or does not respondp.91Cannot delete documents from the print queuep.92Cannot print through USBp.92Jams and misfeeds troubleshootingp.93Paper jam in the printerp.93Paper jam in the paper supportp.93Paper or specialty media misfeedsp.93Print troubleshootingp.94Poor quality at the edges of the pagep.94Streaks or lines on printed imagep.95Print speed is slowp.95Computer slows down when printingp.96Copy and scan troubleshootingp.96Copier or scanner does not respondp.96Scanner unit does not closep.96Poor copy or scanned image qualityp.96Partial copies or scans of documents or photosp.97Scan was not successfulp.97Scanning takes too long or freezes the computerp.97Cannot scan to a computer over a networkp.97Memory card troubleshootingp.98Memory card troubleshooting checklistp.98Nothing happens when a memory card is insertedp.98Cannot print documents from a memory card or flash drivep.98Photos do not transfer from a memory card across a wireless networkp.99Wireless troubleshootingp.99Wireless troubleshooting checklistp.99Resetting the wireless settings to factory defaultsp.100Cannot print over wireless networkp.100The Continue button is unavailablep.104Cannot print and there is a firewall on the computerp.105Wi-Fi indicator light is not litp.105Wi-Fi indicator light is green but the printer does not print (Windows only)p.106Wi-Fi indicator light is still orangep.107Wi-Fi indicator light is blinking orange during installationp.108Wireless print server not installedp.112“Communication not available” message displays when printing wirelesslyp.112Communication with printer lost when connected to Virtual Private Network (VPN)p.114Resolving intermittent wireless communications issuesp.115Noticesp.118Product informationp.118Edition noticep.118UNITED STATES GOVERNMENT RIGHTSp.119Trademarksp.119Licensing noticesp.119Federal Communications Commission (FCC) compliance information statementp.119Hinweis zum GS-Zeichenp.120Noise emission levelsp.120Temperature informationp.121Waste from Electrical and Electronic Equipment (WEEE) directivep.121Product disposalp.121Battery noticep.121ENERGY STARp.121Power consumptionp.122Product power consumptionp.122Power Saverp.122Off modep.122Total energy usagep.122European Community (EC) directives conformityp.123Regulatory notices for telecommunication terminal equipmentp.123Notice to users of the US telephone network: FCC requirementsp.123South Africa telecommunications noticep.124Notice to users of the Canadian telephone networkp.124Notice to users of the New Zealand telephone networkp.125Notice to Users in the European Unionp.126Regulatory notices for wireless productsp.127Exposure to radio frequency radiationp.127Notice to users in Brazilp.127Industry Canada (Canada)p.127Taiwan NCC RF notice statementp.128Notice to users in the European Unionp.128LEXMARK SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENTSp.130Indexp.135
Page 137 of the Lexmark 10E user manual — Table of contents
Page 137 · click to enlarge
Page 137

Table of contents

Contentsp.2Safety informationp.5About your printerp.6Thank you for choosing this printer!p.6Minimizing your printer's environmental impactp.6Finding information about the printerp.7Understanding the parts of the printerp.9Ordering and replacing suppliesp.11Ordering ink cartridgesp.11Using genuine Lexmark ink cartridgesp.11Replacing ink cartridgesp.12Ordering paper and other suppliesp.13Recycling Lexmark productsp.13Using the printer control panel buttons and menusp.14Using the printer control panelp.14Changing temporary settings into new default settingsp.15Changing the Power Saver timeoutp.16Saving energy with Eco-Modep.17Resetting to factory settingsp.17Using the printer softwarep.19Minimum system requirementsp.19Using the Windows printer softwarep.19Using the Macintosh printer softwarep.21Finding and installing optional softwarep.22Updating the printer software (Windows only)p.23Reinstalling the printer softwarep.23Uninstalling the printer softwarep.23Installing the printer softwarep.24Loading paper and original documentsp.25Loading paperp.25Saving paper default settingsp.27Loading original documents on the scanner glassp.28Printingp.29Tips for printingp.29Printing basic documentsp.29Printing a documentp.29Collating printed copiesp.30Printing pages in reverse orderp.30Printing multiple pages on one sheetp.31Printing documents from a memory card or flash drive (Windows only)p.32Printing specialty documentsp.33Printing envelopesp.33Printing labelsp.33Printing on custom-size paperp.34Printing on both sides of the paper (duplexing) manuallyp.35Working with photosp.37Using a memory card or flash drive with the printerp.37Supported memory cards and file typesp.38Printing photos using the printer control panelp.38Printing photos from a memory device using the printer softwarep.39Printing photos from a PictBridge-enabled digital camerap.40Printing photos from a memory device using the proof sheetp.41Printing photos from a digital camera using DPOFp.42Printing from a Bluetooth-enabled devicep.42Setting up a connection between your printer and a Bluetooth-enabled devicep.42Setting the Bluetooth security levelp.43Printing from a Bluetooth-enabled devicep.44Managing print jobsp.45Setting your printer as the default printerp.45Changing the printing modep.45Pausing print jobsp.46Resuming print jobsp.47Canceling print jobsp.47Copyingp.49Tips for copyingp.49Making copiesp.49Copying photosp.49Enlarging or reducing imagesp.50Adjusting copy qualityp.50Making a copy lighter or darkerp.50Collating copies using the printer control panelp.51Repeating an image on one pagep.51Copying multiple pages on one sheetp.52Making a duplex copy manuallyp.52Canceling copy jobsp.53Scanningp.54Tips for scanningp.54Scanning to a local or network computerp.54Scanning to a flash drive or memory cardp.55Scanning photos into an editing applicationp.55Scanning documents into an editing applicationp.57Scanning directly to e-mail using the printer softwarep.57Scanning to a PDFp.58Scanning FAQp.59How can I improve the quality of a scan?p.59How do I scan in black and white?p.59Why am I being asked for a PIN?p.59What is an application list, and how do I update it?p.59Canceling scan jobsp.60Networkingp.61Installing the printer on a wireless networkp.61Wireless network compatibilityp.61Supported network security optionsp.61Printing a network setup pagep.62Information you will need to set up the printer on a wireless networkp.62Installing the printer on a wireless networkp.63Installing the printer on other computersp.63Interpreting the colors of the Wi-Fi indicator lightp.64Special wireless installation instructionsp.64Assigning a static IP addressp.65Changing wireless settings after installationp.65Advanced wireless setupp.66Creating an ad hoc wireless networkp.66Adding a printer to an existing ad hoc wireless networkp.69Configuring the printer wirelessly using WPS (Wi-Fi Protected Setup)p.69Switching between USB and wireless connections (Windows only)p.70Switching between USB and wireless connections (Macintosh only)p.70Sharing a printer in a Windows environmentp.71Sharing a printer in a Macintosh environmentp.72Networking FAQp.73What is Wi-Fi Protected Setup?p.73Where do I find my WEP key or WPA passphrase?p.73What is an SSID?p.73Where do I find my SSID?p.74What is a network?p.74How do I find out what type of security my network is using?p.74How are home networks configured?p.74Why do I need an installation cable?p.76How do I attach the installation cable?p.76How are infrastructure and ad hoc networks different?p.77Finding the signal strengthp.78How can I improve wireless signal strength?p.78How can I make sure my computer and printer are connected to the same wireless network?p.79Can I use my printer on a USB and a network connection at the same time?p.81What is a MAC address?p.81How do I find the MAC address?p.81What is an IP address?p.82What is TCP/IP?p.82How do I locate IP addresses?p.82How are IP addresses assigned?p.83What is a key index?p.83Maintaining the printerp.84Maintaining ink cartridgesp.84Checking ink levelsp.84Aligning the printheadp.84Cleaning the printhead nozzlesp.85Cleaning the exterior of the printerp.86Cleaning the scanner glassp.86Troubleshootingp.87Before you troubleshootp.87Using the Service Center to solve printer problemsp.87If Troubleshooting does not solve your problemp.87Setup troubleshootingp.87Incorrect language appears on the displayp.88Printhead errorsp.88Software did not installp.90Print job does not print or is missing pagesp.90Printer is printing blank pagesp.91Printer is busy or does not respondp.91Cannot delete documents from the print queuep.92Cannot print through USBp.92Jams and misfeeds troubleshootingp.93Paper jam in the printerp.93Paper jam in the paper supportp.93Paper or specialty media misfeedsp.93Print troubleshootingp.94Poor quality at the edges of the pagep.94Streaks or lines on printed imagep.95Print speed is slowp.95Computer slows down when printingp.96Copy and scan troubleshootingp.96Copier or scanner does not respondp.96Scanner unit does not closep.96Poor copy or scanned image qualityp.96Partial copies or scans of documents or photosp.97Scan was not successfulp.97Scanning takes too long or freezes the computerp.97Cannot scan to a computer over a networkp.97Memory card troubleshootingp.98Memory card troubleshooting checklistp.98Nothing happens when a memory card is insertedp.98Cannot print documents from a memory card or flash drivep.98Photos do not transfer from a memory card across a wireless networkp.99Wireless troubleshootingp.99Wireless troubleshooting checklistp.99Resetting the wireless settings to factory defaultsp.100Cannot print over wireless networkp.100The Continue button is unavailablep.104Cannot print and there is a firewall on the computerp.105Wi-Fi indicator light is not litp.105Wi-Fi indicator light is green but the printer does not print (Windows only)p.106Wi-Fi indicator light is still orangep.107Wi-Fi indicator light is blinking orange during installationp.108Wireless print server not installedp.112“Communication not available” message displays when printing wirelesslyp.112Communication with printer lost when connected to Virtual Private Network (VPN)p.114Resolving intermittent wireless communications issuesp.115Noticesp.118Product informationp.118Edition noticep.118UNITED STATES GOVERNMENT RIGHTSp.119Trademarksp.119Licensing noticesp.119Federal Communications Commission (FCC) compliance information statementp.119Hinweis zum GS-Zeichenp.120Noise emission levelsp.120Temperature informationp.121Waste from Electrical and Electronic Equipment (WEEE) directivep.121Product disposalp.121Battery noticep.121ENERGY STARp.121Power consumptionp.122Product power consumptionp.122Power Saverp.122Off modep.122Total energy usagep.122European Community (EC) directives conformityp.123Regulatory notices for telecommunication terminal equipmentp.123Notice to users of the US telephone network: FCC requirementsp.123South Africa telecommunications noticep.124Notice to users of the Canadian telephone networkp.124Notice to users of the New Zealand telephone networkp.125Notice to Users in the European Unionp.126Regulatory notices for wireless productsp.127Exposure to radio frequency radiationp.127Notice to users in Brazilp.127Industry Canada (Canada)p.127Taiwan NCC RF notice statementp.128Notice to users in the European Unionp.128LEXMARK SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENTSp.130Indexp.135
Page 138 of the Lexmark 10E user manual — Table of contents
Page 138 · click to enlarge
Page 138

Table of contents

Contentsp.2Safety informationp.5About your printerp.6Thank you for choosing this printer!p.6Minimizing your printer's environmental impactp.6Finding information about the printerp.7Understanding the parts of the printerp.9Ordering and replacing suppliesp.11Ordering ink cartridgesp.11Using genuine Lexmark ink cartridgesp.11Replacing ink cartridgesp.12Ordering paper and other suppliesp.13Recycling Lexmark productsp.13Using the printer control panel buttons and menusp.14Using the printer control panelp.14Changing temporary settings into new default settingsp.15Changing the Power Saver timeoutp.16Saving energy with Eco-Modep.17Resetting to factory settingsp.17Using the printer softwarep.19Minimum system requirementsp.19Using the Windows printer softwarep.19Using the Macintosh printer softwarep.21Finding and installing optional softwarep.22Updating the printer software (Windows only)p.23Reinstalling the printer softwarep.23Uninstalling the printer softwarep.23Installing the printer softwarep.24Loading paper and original documentsp.25Loading paperp.25Saving paper default settingsp.27Loading original documents on the scanner glassp.28Printingp.29Tips for printingp.29Printing basic documentsp.29Printing a documentp.29Collating printed copiesp.30Printing pages in reverse orderp.30Printing multiple pages on one sheetp.31Printing documents from a memory card or flash drive (Windows only)p.32Printing specialty documentsp.33Printing envelopesp.33Printing labelsp.33Printing on custom-size paperp.34Printing on both sides of the paper (duplexing) manuallyp.35Working with photosp.37Using a memory card or flash drive with the printerp.37Supported memory cards and file typesp.38Printing photos using the printer control panelp.38Printing photos from a memory device using the printer softwarep.39Printing photos from a PictBridge-enabled digital camerap.40Printing photos from a memory device using the proof sheetp.41Printing photos from a digital camera using DPOFp.42Printing from a Bluetooth-enabled devicep.42Setting up a connection between your printer and a Bluetooth-enabled devicep.42Setting the Bluetooth security levelp.43Printing from a Bluetooth-enabled devicep.44Managing print jobsp.45Setting your printer as the default printerp.45Changing the printing modep.45Pausing print jobsp.46Resuming print jobsp.47Canceling print jobsp.47Copyingp.49Tips for copyingp.49Making copiesp.49Copying photosp.49Enlarging or reducing imagesp.50Adjusting copy qualityp.50Making a copy lighter or darkerp.50Collating copies using the printer control panelp.51Repeating an image on one pagep.51Copying multiple pages on one sheetp.52Making a duplex copy manuallyp.52Canceling copy jobsp.53Scanningp.54Tips for scanningp.54Scanning to a local or network computerp.54Scanning to a flash drive or memory cardp.55Scanning photos into an editing applicationp.55Scanning documents into an editing applicationp.57Scanning directly to e-mail using the printer softwarep.57Scanning to a PDFp.58Scanning FAQp.59How can I improve the quality of a scan?p.59How do I scan in black and white?p.59Why am I being asked for a PIN?p.59What is an application list, and how do I update it?p.59Canceling scan jobsp.60Networkingp.61Installing the printer on a wireless networkp.61Wireless network compatibilityp.61Supported network security optionsp.61Printing a network setup pagep.62Information you will need to set up the printer on a wireless networkp.62Installing the printer on a wireless networkp.63Installing the printer on other computersp.63Interpreting the colors of the Wi-Fi indicator lightp.64Special wireless installation instructionsp.64Assigning a static IP addressp.65Changing wireless settings after installationp.65Advanced wireless setupp.66Creating an ad hoc wireless networkp.66Adding a printer to an existing ad hoc wireless networkp.69Configuring the printer wirelessly using WPS (Wi-Fi Protected Setup)p.69Switching between USB and wireless connections (Windows only)p.70Switching between USB and wireless connections (Macintosh only)p.70Sharing a printer in a Windows environmentp.71Sharing a printer in a Macintosh environmentp.72Networking FAQp.73What is Wi-Fi Protected Setup?p.73Where do I find my WEP key or WPA passphrase?p.73What is an SSID?p.73Where do I find my SSID?p.74What is a network?p.74How do I find out what type of security my network is using?p.74How are home networks configured?p.74Why do I need an installation cable?p.76How do I attach the installation cable?p.76How are infrastructure and ad hoc networks different?p.77Finding the signal strengthp.78How can I improve wireless signal strength?p.78How can I make sure my computer and printer are connected to the same wireless network?p.79Can I use my printer on a USB and a network connection at the same time?p.81What is a MAC address?p.81How do I find the MAC address?p.81What is an IP address?p.82What is TCP/IP?p.82How do I locate IP addresses?p.82How are IP addresses assigned?p.83What is a key index?p.83Maintaining the printerp.84Maintaining ink cartridgesp.84Checking ink levelsp.84Aligning the printheadp.84Cleaning the printhead nozzlesp.85Cleaning the exterior of the printerp.86Cleaning the scanner glassp.86Troubleshootingp.87Before you troubleshootp.87Using the Service Center to solve printer problemsp.87If Troubleshooting does not solve your problemp.87Setup troubleshootingp.87Incorrect language appears on the displayp.88Printhead errorsp.88Software did not installp.90Print job does not print or is missing pagesp.90Printer is printing blank pagesp.91Printer is busy or does not respondp.91Cannot delete documents from the print queuep.92Cannot print through USBp.92Jams and misfeeds troubleshootingp.93Paper jam in the printerp.93Paper jam in the paper supportp.93Paper or specialty media misfeedsp.93Print troubleshootingp.94Poor quality at the edges of the pagep.94Streaks or lines on printed imagep.95Print speed is slowp.95Computer slows down when printingp.96Copy and scan troubleshootingp.96Copier or scanner does not respondp.96Scanner unit does not closep.96Poor copy or scanned image qualityp.96Partial copies or scans of documents or photosp.97Scan was not successfulp.97Scanning takes too long or freezes the computerp.97Cannot scan to a computer over a networkp.97Memory card troubleshootingp.98Memory card troubleshooting checklistp.98Nothing happens when a memory card is insertedp.98Cannot print documents from a memory card or flash drivep.98Photos do not transfer from a memory card across a wireless networkp.99Wireless troubleshootingp.99Wireless troubleshooting checklistp.99Resetting the wireless settings to factory defaultsp.100Cannot print over wireless networkp.100The Continue button is unavailablep.104Cannot print and there is a firewall on the computerp.105Wi-Fi indicator light is not litp.105Wi-Fi indicator light is green but the printer does not print (Windows only)p.106Wi-Fi indicator light is still orangep.107Wi-Fi indicator light is blinking orange during installationp.108Wireless print server not installedp.112“Communication not available” message displays when printing wirelesslyp.112Communication with printer lost when connected to Virtual Private Network (VPN)p.114Resolving intermittent wireless communications issuesp.115Noticesp.118Product informationp.118Edition noticep.118UNITED STATES GOVERNMENT RIGHTSp.119Trademarksp.119Licensing noticesp.119Federal Communications Commission (FCC) compliance information statementp.119Hinweis zum GS-Zeichenp.120Noise emission levelsp.120Temperature informationp.121Waste from Electrical and Electronic Equipment (WEEE) directivep.121Product disposalp.121Battery noticep.121ENERGY STARp.121Power consumptionp.122Product power consumptionp.122Power Saverp.122Off modep.122Total energy usagep.122European Community (EC) directives conformityp.123Regulatory notices for telecommunication terminal equipmentp.123Notice to users of the US telephone network: FCC requirementsp.123South Africa telecommunications noticep.124Notice to users of the Canadian telephone networkp.124Notice to users of the New Zealand telephone networkp.125Notice to Users in the European Unionp.126Regulatory notices for wireless productsp.127Exposure to radio frequency radiationp.127Notice to users in Brazilp.127Industry Canada (Canada)p.127Taiwan NCC RF notice statementp.128Notice to users in the European Unionp.128LEXMARK SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENTSp.130Indexp.135
Page 139 of the Lexmark 10E user manual — Table of contents
Page 139 · click to enlarge
Page 139

Table of contents

Contentsp.2Safety informationp.5About your printerp.6Thank you for choosing this printer!p.6Minimizing your printer's environmental impactp.6Finding information about the printerp.7Understanding the parts of the printerp.9Ordering and replacing suppliesp.11Ordering ink cartridgesp.11Using genuine Lexmark ink cartridgesp.11Replacing ink cartridgesp.12Ordering paper and other suppliesp.13Recycling Lexmark productsp.13Using the printer control panel buttons and menusp.14Using the printer control panelp.14Changing temporary settings into new default settingsp.15Changing the Power Saver timeoutp.16Saving energy with Eco-Modep.17Resetting to factory settingsp.17Using the printer softwarep.19Minimum system requirementsp.19Using the Windows printer softwarep.19Using the Macintosh printer softwarep.21Finding and installing optional softwarep.22Updating the printer software (Windows only)p.23Reinstalling the printer softwarep.23Uninstalling the printer softwarep.23Installing the printer softwarep.24Loading paper and original documentsp.25Loading paperp.25Saving paper default settingsp.27Loading original documents on the scanner glassp.28Printingp.29Tips for printingp.29Printing basic documentsp.29Printing a documentp.29Collating printed copiesp.30Printing pages in reverse orderp.30Printing multiple pages on one sheetp.31Printing documents from a memory card or flash drive (Windows only)p.32Printing specialty documentsp.33Printing envelopesp.33Printing labelsp.33Printing on custom-size paperp.34Printing on both sides of the paper (duplexing) manuallyp.35Working with photosp.37Using a memory card or flash drive with the printerp.37Supported memory cards and file typesp.38Printing photos using the printer control panelp.38Printing photos from a memory device using the printer softwarep.39Printing photos from a PictBridge-enabled digital camerap.40Printing photos from a memory device using the proof sheetp.41Printing photos from a digital camera using DPOFp.42Printing from a Bluetooth-enabled devicep.42Setting up a connection between your printer and a Bluetooth-enabled devicep.42Setting the Bluetooth security levelp.43Printing from a Bluetooth-enabled devicep.44Managing print jobsp.45Setting your printer as the default printerp.45Changing the printing modep.45Pausing print jobsp.46Resuming print jobsp.47Canceling print jobsp.47Copyingp.49Tips for copyingp.49Making copiesp.49Copying photosp.49Enlarging or reducing imagesp.50Adjusting copy qualityp.50Making a copy lighter or darkerp.50Collating copies using the printer control panelp.51Repeating an image on one pagep.51Copying multiple pages on one sheetp.52Making a duplex copy manuallyp.52Canceling copy jobsp.53Scanningp.54Tips for scanningp.54Scanning to a local or network computerp.54Scanning to a flash drive or memory cardp.55Scanning photos into an editing applicationp.55Scanning documents into an editing applicationp.57Scanning directly to e-mail using the printer softwarep.57Scanning to a PDFp.58Scanning FAQp.59How can I improve the quality of a scan?p.59How do I scan in black and white?p.59Why am I being asked for a PIN?p.59What is an application list, and how do I update it?p.59Canceling scan jobsp.60Networkingp.61Installing the printer on a wireless networkp.61Wireless network compatibilityp.61Supported network security optionsp.61Printing a network setup pagep.62Information you will need to set up the printer on a wireless networkp.62Installing the printer on a wireless networkp.63Installing the printer on other computersp.63Interpreting the colors of the Wi-Fi indicator lightp.64Special wireless installation instructionsp.64Assigning a static IP addressp.65Changing wireless settings after installationp.65Advanced wireless setupp.66Creating an ad hoc wireless networkp.66Adding a printer to an existing ad hoc wireless networkp.69Configuring the printer wirelessly using WPS (Wi-Fi Protected Setup)p.69Switching between USB and wireless connections (Windows only)p.70Switching between USB and wireless connections (Macintosh only)p.70Sharing a printer in a Windows environmentp.71Sharing a printer in a Macintosh environmentp.72Networking FAQp.73What is Wi-Fi Protected Setup?p.73Where do I find my WEP key or WPA passphrase?p.73What is an SSID?p.73Where do I find my SSID?p.74What is a network?p.74How do I find out what type of security my network is using?p.74How are home networks configured?p.74Why do I need an installation cable?p.76How do I attach the installation cable?p.76How are infrastructure and ad hoc networks different?p.77Finding the signal strengthp.78How can I improve wireless signal strength?p.78How can I make sure my computer and printer are connected to the same wireless network?p.79Can I use my printer on a USB and a network connection at the same time?p.81What is a MAC address?p.81How do I find the MAC address?p.81What is an IP address?p.82What is TCP/IP?p.82How do I locate IP addresses?p.82How are IP addresses assigned?p.83What is a key index?p.83Maintaining the printerp.84Maintaining ink cartridgesp.84Checking ink levelsp.84Aligning the printheadp.84Cleaning the printhead nozzlesp.85Cleaning the exterior of the printerp.86Cleaning the scanner glassp.86Troubleshootingp.87Before you troubleshootp.87Using the Service Center to solve printer problemsp.87If Troubleshooting does not solve your problemp.87Setup troubleshootingp.87Incorrect language appears on the displayp.88Printhead errorsp.88Software did not installp.90Print job does not print or is missing pagesp.90Printer is printing blank pagesp.91Printer is busy or does not respondp.91Cannot delete documents from the print queuep.92Cannot print through USBp.92Jams and misfeeds troubleshootingp.93Paper jam in the printerp.93Paper jam in the paper supportp.93Paper or specialty media misfeedsp.93Print troubleshootingp.94Poor quality at the edges of the pagep.94Streaks or lines on printed imagep.95Print speed is slowp.95Computer slows down when printingp.96Copy and scan troubleshootingp.96Copier or scanner does not respondp.96Scanner unit does not closep.96Poor copy or scanned image qualityp.96Partial copies or scans of documents or photosp.97Scan was not successfulp.97Scanning takes too long or freezes the computerp.97Cannot scan to a computer over a networkp.97Memory card troubleshootingp.98Memory card troubleshooting checklistp.98Nothing happens when a memory card is insertedp.98Cannot print documents from a memory card or flash drivep.98Photos do not transfer from a memory card across a wireless networkp.99Wireless troubleshootingp.99Wireless troubleshooting checklistp.99Resetting the wireless settings to factory defaultsp.100Cannot print over wireless networkp.100The Continue button is unavailablep.104Cannot print and there is a firewall on the computerp.105Wi-Fi indicator light is not litp.105Wi-Fi indicator light is green but the printer does not print (Windows only)p.106Wi-Fi indicator light is still orangep.107Wi-Fi indicator light is blinking orange during installationp.108Wireless print server not installedp.112“Communication not available” message displays when printing wirelesslyp.112Communication with printer lost when connected to Virtual Private Network (VPN)p.114Resolving intermittent wireless communications issuesp.115Noticesp.118Product informationp.118Edition noticep.118UNITED STATES GOVERNMENT RIGHTSp.119Trademarksp.119Licensing noticesp.119Federal Communications Commission (FCC) compliance information statementp.119Hinweis zum GS-Zeichenp.120Noise emission levelsp.120Temperature informationp.121Waste from Electrical and Electronic Equipment (WEEE) directivep.121Product disposalp.121Battery noticep.121ENERGY STARp.121Power consumptionp.122Product power consumptionp.122Power Saverp.122Off modep.122Total energy usagep.122European Community (EC) directives conformityp.123Regulatory notices for telecommunication terminal equipmentp.123Notice to users of the US telephone network: FCC requirementsp.123South Africa telecommunications noticep.124Notice to users of the Canadian telephone networkp.124Notice to users of the New Zealand telephone networkp.125Notice to Users in the European Unionp.126Regulatory notices for wireless productsp.127Exposure to radio frequency radiationp.127Notice to users in Brazilp.127Industry Canada (Canada)p.127Taiwan NCC RF notice statementp.128Notice to users in the European Unionp.128LEXMARK SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENTSp.130Indexp.135
Page 140 of the Lexmark 10E user manual — Index
Page 140 · click to enlarge
Page 140

locating 73 WPA2 61 WPS 69

WPA passphrase · Index

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Lexmark 10E

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lexmark 10E

Be the first to ask — other owners or our team will answer.

Original document

Lexmark 10E manual PDF

140 pages·1.5 MB·Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…