EN
LevelOne logo
Official user manual

LevelOne WAP-0005

94 pages·3.2 MB·Webcam·PDF·ENDEFRITNLJA
LevelOne WAP-0005
Table of Contents 51 sections Chapter 1 Introduction · Features of your Wireless Access Point · Package Contents · Physical Details · … ShowHide
Page 1 of the LevelOne WAP-0005 user manual — LevelOne
Page 1 · click to enlarge
Page 1

LevelOne

WAP - 0005

108 Mbps Wireless Access Point

User’s Manual

Page 4 of the LevelOne WAP-0005 user manual — Features of your Wireless Access Point
Page 4 · click to enlarge
Page 4

Chapter 1 Introduction

This Chapter provides an overview of the Wireless Access Point's features and capabilities.

Congratulations on the purchase of your new Wireless Access Point. The Wireless Access Point links your 802.11g or 802.11b Wireless Stations to your wired LAN. The Wireless stations and devices on the wired LAN are then on the same network, and can communicate with each other without regard for whether they are connected to the network via a Wireless or wired connection.

LevelOne WAP-0005 — Chapter 1 Introduction diagram (page 4)
Fig. 1 · Chapter 1 Introduction
Figure 1Wireless Access Point

The auto-sensing capability of the Wireless Access Point allows packet transmission up to 54Mbps for maximum throughput, or automatic speed reduction to lower speeds when the environment does not permit maximum throughput.

Features of your Wireless Access Point

The Wireless Access Point incorporates many advanced features, carefully designed to provide sophisticated functions while being easy to use.

  • Standards Compliant. The Wireless Router complies with the IEEE802.11g (DSSS) specifications for Wireless LANs.
  • Supports both 802.11b and 802.11g Wireless Stations. The 802.11g standard provides for backward compatibility with the 802.11b standard, so both 802.11b and 802.11g Wireless stations can be used simultaneously.
  • 108Mbps Wireless Connections. On both the 2.4GHz (802.11b & 802.11g) and 5GHz (802.11a) bands, 108Mbps connections are available to compatible clients.
  • Simple Configuration. If the default settings are unsuitable, they can be changed quickly and easily.
Page 5 of the LevelOne WAP-0005 user manual — Advanced Features
Page 5 · click to enlarge
Page 5
  • DHCP Client Support. D ynamic H ost C onfiguration P rotocol provides a dynamic IP address to PCs and other devices upon request. The Wireless Access Point can act as a DHCP Client , and obtain an IP address and related information from your existing DHPC Server.
  • Upgradeable Firmware. Firmware is stored in a flash memory and can be upgraded easily, using only your Web Browser.
  • PoE Support. You can user PoE (Power over Ethernet) to provide power to the Wireless Access Point, so only a single cable connection is required.

Security Features

  • WEP support. Support for WEP (Wired Equivalent Privacy) is included. Both 64 Bit and 128 Bit keys are supported.
  • WPA support. Support for WPA is included. WPA is more secure than WEP, and should be used if possible. Both TKIP and AES encryption methods are supported.
  • 802.1x Support. Support for 802.1x mode is included, providing for the industrialstrength wireless security of 802.1x authentication and authorization.
  • Radius Client Support. The Wireless Access Point can login to your existing Radius Server (as a Radius client).
  • Radius MAC Authentication. You can centralize the checking of Wireless Station MAC addresses by using a Radius Server.
  • Dynamic WEP key Support . In 802.1x mode, either fixed or Dynamic WEP keys can be used.
  • Access Control. The Access Control feature can check the MAC address of Wireless clients to ensure that only trusted Wireless Stations can use the Wireless Access Point to gain access to your LAN.
  • Password - protected Configuration . Optional password protection is provided to prevent unauthorized users from modifying the configuration data and settings.

Advanced Features

  • Command Line Interface. If desired, the command line interface (CLI) can be used for configuration. This provides the possibility of creating scripts to perform common configuration changes.
  • NetBIOS & WINS Support. Support for both NetBIOS broadcast and WINS (Windows Internet Naming Service) allows the Wireless Access Point to easily fit into your existing Windows network.
  • Radius Accounting Support. If you have a Radius Server, you can use it to provide accounting data on Wireless clients.
  • SNMP Support. SNMP (Simple Network Management Protocol) is supported, allowing you to use a SNMP program to manage the Wireless Access Point.
  • UAM Support . The Wireless Access Point supports UAM (Universal Access Method), making it suitable for use in Internet cafes and other sites where user access time must be accounted for.
  • WDS Support . Support for WDS (Wireless Distribution System) allows the Wireless Access Point to act as a Wireless Bridge. Both Point-to-Point and Multi-Point Bridge modes are supported.
Page 6 of the LevelOne WAP-0005 user manual — Front Panel LEDs
Page 6 · click to enlarge
Page 6

Package Contents

The following items should be included:

  • Wireless Access Point
  • Power Adapter
  • Quick Start Guide
  • CD-ROM containing the on-line manual and setup utility.

If any of the above items are damaged or missing, please contact your dealer immediately.

Physical Details

Front Panel LEDs

LevelOne WAP-0005 — Front Panel LEDs diagram (page 6)
Fig. 2 · Front Panel LEDs
Figure 2Front Panel

Status On - Error condition.

Off - Normal operation.

Blinking - During start up, and when the Firmware is being upgraded.

Power On - Normal operation.

Off - No power

LAN On - The LAN (Ethernet) port is active.

Off - No active connection on the LAN (Ethernet) port.

Flashing - Data is being transmitted or received via the corresponding LAN (Ethernet) port.

Off - Error- Wireless connection is not available.

Flashing - Data is being transmitted or received via the Wireless access point. Data includes "network traffic" as well as user data.

Introduction · Wireless LAN · On - Idle

Page 7 of the LevelOne WAP-0005 user manual — Rear Panel
Page 7 · click to enlarge
Page 7

Rear Panel

LevelOne WAP-0005 — Rear Panel diagram (page 7)
Fig. 3 · Rear Panel

Figure 3 Rear Panel

Antenna One antenna (aerial) is supplied. Best results are usually obtained with the antenna in a vertical position.

Console port DB9 female RS232 port.

Reset Button This button has two (2) functions:

  • Reboot . When pressed and released, the Wireless Access Point will reboot (restart).
  • Reset to Factory Defaults . This button can also be used to clear ALL data and restore ALL settings to the factory default values.

To Clear All Data and restore the factory default values: 1. Power Off the Access Point 2. Hold the Reset Button down while you Power On the Access Point. 3. Continue holding the Reset Button until the Status (Red) LED blinks TWICE. 4. Release the Reset Button. The factory default configuration has now been restored, and the Access Point is ready for use.

Ethernet Use a standard LAN cable (RJ45 connectors) to connect this port to a 10BaseT or 100BaseT hub on your LAN.

Power port Connect the supplied power adapter here.

Page 8 of the LevelOne WAP-0005 user manual — Procedure
Page 8 · click to enlarge
Page 8

Chapter 2 Installation

This Chapter covers the physical installation of the Wireless Access Point.

Requirements

Requirements:

  • TCP/IP network
  • Ethernet cable with RJ-45 connectors
  • Installed Wireless network adapter for each PC that will be wirelessly connected to the network

Procedure

1. Select a suitable location for the installation of your Wireless Access Point. To maximize reliability and performance, follow these guidelines:
  • Use an elevated location, such as wall mounted or on the top of a cubicle.
  • Place the Wireless Access Point near the center of your wireless coverage area.
  • If possible, ensure there are no thick walls or metal shielding between the Wireless Access Point and Wireless stations. Under ideal conditions, the Wireless Access Point has a range of around 150 meters (450 feet). The range is reduced, and transmission speed is lower, if there are any obstructions between Wireless devices.
LevelOne WAP-0005 — Procedure diagram (page 8)
Fig. 4 · Procedure
Figure 4Installation Diagram
2. Use a standard LAN cable to connect the “Ethernet” port on the Wireless Access Point to a 10/100BaseT hub on your LAN.
Page 9 of the LevelOne WAP-0005 user manual — Using PoE (Power over Ethernet)
Page 9 · click to enlarge
Page 9
3. Connect the supplied power adapter to the Wireless Access Point and a convenient power outlet, and power up. NOTE: If you wish to use PoE (Power over Ethernet), refer to the following section. 4. Check the LEDs:
  • The Status LED should flash, then turn OFF.
  • The Power, WLAN, and LAN LED should be ON.

For more information, refer to Front Panel LEDs in Chapter 1.

Using PoE (Power over Ethernet)

The Wireless Access Point supports PoE (Power over Ethernet). To use PoE: 1. Do not connect the supplied power adapter to the Wireless Access Point. 2. Connect one end of a standard (category 5) LAN cable to the Ethernet port on the Wire- less Access Point. 3. Connect the other end of the LAN cable to the powered Ethernet port on a suitable PoE Adapter. (24V DC, 500mA) 4. Connect the unpowered Ethernet port on the PoE adapter to your Hub or switch. 5. Connect the power supply to the PoE adapter and power up. 6. Check the LEDs on the Wireless Access Point to see it is drawing power via the Ethernet- connection.

LevelOne WAP-0005 — Using PoE (Power over Ethernet) diagram (page 9)
Fig. 5 · Using PoE (Power over Ethernet)
Figure 5Using PoE (Power over Ethernet)
Page 10 of the LevelOne WAP-0005 user manual — Main Screen
Page 10 · click to enlarge
Page 10

Chapter 3 Access Point Setup

This Chapter provides details of the Setup process for Basic Operation of your Wireless Access Point.

Overview

This chapter describes the setup procedure to make the Wireless Access Point a valid device on your LAN, and to function as an Access Point for your Wireless Stations.

Wireless Stations may also require configuration. For details, see Chapter 4 - Wireless Station Configuration.

The Wireless Access Point can be configured using either the supplied Windows utility or your Web Browser

Setup using the Windows Utility

A simple Windows setup utility is supplied on the CD-ROM. This utility can be used to assign a suitable IP address to the Wireless Access Point. Using this utility is recommended, because it can locate the Wireless Access Point even if it has an invalid IP address.

Installation

1. Insert the supplied CD-ROM in your drive. 2. If the utility does not start automatically, run the SETUP program in the root folder. 3. Follow the prompts to complete the installation.

Main Screen

  • Start the program by using the icon created by the setup program.
  • When run, the program searches the network for all active Wireless Access Points, then lists them on screen, as shown by the example below.
Page 11 of the LevelOne WAP-0005 user manual — Buttons
Page 11 · click to enlarge
Page 11
LevelOne WAP-0005 — Chapter 3 Access Point Setup diagram (page 11)
Fig. 6 · Chapter 3 Access Point Setup
Figure 6Management utility Screen

Wireless Access Points

The main panel displays a list of all Wireless Access Points found on the network. For each Access Point, the following data is shown:

Server NameThe Server Name is shown on a sticker on the base of the device. IP addressThe IP address for the Wireless Access Point. MAC AddressThe hardware or physical address of the Wireless Access Point. IEEE StandardThe wireless standard or standards used by the Wireless Access Point (e.g. 802.11b, 802.11g) FW VersionThe current Firmware version installed in the Wireless Access Point. DescriptionAny extra information for the Wireless Access Point, entered by the administrator.

Buttons

RefreshClick this button to update the Wireless Access Point device listing after changing the name or IP Address. Detail InfoWhen clicked, additional information about the selected Access Point will be displayed. Web ManagementUse this button to connect to the Wireless Access Point's Webbased management interface. Set IP AddressClick this button if you want to change the IP Address of the Wireless Access Point. ExitExit the Management utility program by clicking this button.
Page 12 of the LevelOne WAP-0005 user manual — Setup Procedure
Page 12 · click to enlarge
Page 12

Setup Procedure

1. Select the desired Wireless Access Point. 2. Click the Set IP Address button. 3. If prompted, enter the user name and password. The default values are admin for the User Name , and password for the Password.
4. Ensure the IP address , Network Mask , and Gateway are correct for your LAN. Save any changes. 5. Click the Web Management button to connect to the selected Wireless Access Point using your Web Browser. If prompted, enter the User Name and Password again. 6. Configure the following screens, using the on-line help if necessary. The following section also provides more details about each of these screens.
  • Wireless - Basic (Basic Wireless settings)
  • Wireless - Security (Wireless Security)
  • Management - Admin Login (Set login name and password)
7. Setup is now complete.

Setup

Page 13 of the LevelOne WAP-0005 user manual — HTTP://SC2D631A
Page 13 · click to enlarge
Page 13

Setup using a Web Browser

Your Browser must support JavaScript. The configuration program has been tested on the following browsers:

  • Netscape V4.08 or later
  • Internet Explorer V4 or later

Setup Procedure

Before commencing, install the Wireless Access Point in your LAN, as described previously.

1. Check the Wireless Access Point to determine its Default Name . This is shown on a label on the base or rear, and is in the following format:

Where xxxxxx is a set of 6 Hex characters ( 0 ~ 9, and A ~ F ).

2. Use a PC which is already connected to your LAN, either by a wired connection or another Access Point.
  • Until the Wireless Access Point is configured, establishing a Wireless connection to it may be not possible.
  • If your LAN contains a Router or Routers, ensure the PC used for configuration is on the same LAN segment as the Wireless Access Point. 3. Start your Web browser. 4. In the Address box, enter "<a href='HTTP://"' rel="nofollow noopener" target="_blank">HTTP://"</a> and the Default Name of the Wireless Access Point e.g.

HTTP://SC2D631A

5. You should then see a login prompt, which will ask for a User Name and Password . Enter admin for the User Name , and password for the Password . These are the default values. The password can and should be changed. Always enter the current user name and password, as set on the Admin Login screen.
LevelOne WAP-0005 — HTTP://SC2D631A diagram (page 13)
Fig. 7
Figure 7Password Dialog
6. You will then see the Status screen, which displays the current settings and status. No data input is possible on this screen.

SCxxxxxx

Page 14 of the LevelOne WAP-0005 user manual — If you can't connect:
Page 14 · click to enlarge
Page 14
7. From the menu, check the following screens, and configure as necessary for your environment. Details of these screens and settings are described in the following sections of this chapter.
  • System
  • Access Control
  • Wireless
  • Basic
  • Security
  • Advanced
  • Management
  • Admin Login (Set login name and password) 8. Setup of the Wireless Access Point is now complete. Wireless stations must now be set to match the Wireless Access Point. See Chapter 4 for details.

If you can't connect:

It is likely that your PC’s IP address is incompatible with the Wireless Access Point’s IP address. This can happen if your LAN does not have a DHCP Server. The default IP address of the Wireless Access Point is 192.168.0.228, with a Network Mask of 255.255.255.0.

If your PC’s IP address is not compatible with this, you must change your PC’s IP address to an unused value in the range 192.168.0.1 ~ 192.168.0.254, with a Network Mask of 255.255.255.0. See Appendix C - Windows TCP/IP for details for this procedure.

Setup

Page 15 of the LevelOne WAP-0005 user manual — Status Screen
Page 15 · click to enlarge
Page 15

Status Screen

When you first connect, you will see the Status screen. This displays the current settings and status of the Wireless Access Point. No data can be input on this screen.

LevelOne WAP-0005 — Status Screen diagram (page 15)
Fig. 8 · Status Screen
Figure 8Status Screen

For further details of this screen, refer to Status Screen in Chapter 5.

Page 16 of the LevelOne WAP-0005 user manual — Data - System Screen
Page 16 · click to enlarge
Page 16

System Screen

Click System on the menu to view a screen like the following.

LevelOne WAP-0005 — System Screen diagram (page 16)
Fig. 9 · System Screen
Figure 9System Screen

Data - System Screen

Enter a suitable name for this Access Point.

Description If desired, you can enter a description for the Access Point.

Country Domain Select the country or domain matching your current location.

DHCP Client Select this option if you have a DHCP Server on your LAN, and you wish the Access Point to obtain an IP address automatically.

Fixed If selected, the following data must be entered.

  • IP Address - The IP Address of this device. Enter an unused IP address from the address range on your LAN.
  • Subnet Mask - The Network Mask associated with the IP Address above. Enter the value used by other devices on your LAN.
  • Gateway - The IP Address of your Gateway or Router. Enter the value used by other devices on your LAN.
  • DNS - Enter the DNS (Domain Name Server) used by PCs on your LAN.
Show 4 more labels / short text on this page
Setup · Identification · Access Point Name · IP Address
Page 17 of the LevelOne WAP-0005 user manual — Data - Access Control Screen
Page 17 · click to enlarge
Page 17

WINS

Enable WINS If your LAN has a WINS server, you can enable this to have this AP register with the WINS server.

WINS Server Name/IP Address

Enter the name or IP address of your WINS server.

HTTP

HTTP Port Enter the port number to be used when connecting to this interface. The default value is 80.

If desired, you can enable this option. If enabled, you will able to connect to this AP using a Telnet client. You will have to provide the same login data (user name, password) as for a HTTP (Web) connec- tion.

Access Control

This feature can be used to block access to your LAN by unknown or untrusted wireless stations.

Click Access Control on the menu to view a screen like the following.

LevelOne WAP-0005 — Access Control diagram (page 17)
Fig. 10 · Access Control
Figure 10Access Control Screen

Data - Access Control Screen

Enable Use this checkbox to Enable or Disable this feature as desired.

Trusted Stations This table lists any Wireless Stations you have designated as "Trusted". If you have not added any stations, this table will be empty. For each Wireless station, the following data is displayed:

  • MAC Address - the MAC or physical address of each Wireless station.
  • Connected - this indicates whether or not the Wireless station is currently associates with this Access Point.

Telnet · Enable Telnet Management

Page 18 of the LevelOne WAP-0005 user manual — Data - Trusted Wireless Stations
Page 18 · click to enlarge
Page 18

Modify List To change the list of Trusted Stations (Add, Edit, or Delete a Wireless Station or Stations), click this button. You will then see the Trusted Wireless Stations screen, described below.

Read from File To upload a list of Trusted Stations from a file on your PC, click this button.

Write to File To download the current list of Trusted Stations from the Access Point to a file on your PC, click this button.

Trusted Wireless Stations

To change the list of trusted wireless stations, use the Modify List button on the Access Control screen. You will see a screen like the sample below.

LevelOne WAP-0005 — Trusted Wireless Stations diagram (page 18)
Fig. 11 · Trusted Wireless Stations
Figure 11Trusted Wireless Stations

Data - Trusted Wireless Stations

This lists any Wireless Stations which you have designated as “Trusted”.

This list any Wireless Stations detected by the Access Point, which you have not designated as "Trusted".

Address The MAC (physical) address of the Trusted Wireless Station. Use this when adding or editing a Trusted Station.

<< Add a Trusted Wireless Station to the list (move from the "Other Stations" list).

  • Select an entry (or entries) in the "Other Stations" list, and click the " << " button.
  • Enter the Address (MAC or physical address) of the wireless station, and click the "Add " button.
Show 5 more labels / short text on this page
Setup · Buttons · Trusted Wireless Stations · Other Wireless Stations · Buttons
Page 19 of the LevelOne WAP-0005 user manual — Access Control
Page 19 · click to enlarge
Page 19

>> Delete a Trusted Wireless Station from the list (move to the "Other Stations" list).

  • Select an entry (or entries) in the "Trusted Stations" list.
  • Click the " >> " button.

Select All Select all of the Stations listed in the "Other Stations" list.

Select None De-select any Stations currently selected in the "Other Stations" list.

Edit To change an existing entry in the "Trusted Stations" list, select it and click this button. 1. Select the Station in the "Trusted Station" list. 2. Click the "Edit" button. The address will be copied to the "Address" field, and the "Add" button will change to "Update". 3. Edit the address (MAC or physical address) as required. 4. Click "Update" to save your changes.

Add To add a Trusted Station which is not in the "Other Wireless Stations" list, enter the required data and click this button.

Clear Clear the Address field.

Page 20 of the LevelOne WAP-0005 user manual — Data - Basic Settings Screen
Page 20 · click to enlarge
Page 20

Wireless Screens

There are 3 configuration screens available:

  • Basic Settings
  • Security
  • Advanced

Basic Settings Screen

The settings on this screen must match the settings used by Wireless Stations.

Click Basic on the menu to view a screen like the following.

LevelOne WAP-0005 — Basic Settings Screen diagram (page 20)
Fig. 12 · Basic Settings Screen
Figure 12Basic Settings Screen

Data - Basic Settings Screen

Wireless Mode Select the desired option:

  • Disable - select this if for some reason you do not this AP to transmit or receive at all.
  • 802.11b and 802.11g - this is the default, and will allow connections by both 802.11b and 802.1g wireless stations.
  • 802.11b - if selected, only 802.11b connections are allowed. 802.11g wireless stations will only be able to connect if they are fully backward-compatible with the 802.11b standard.
  • 802.11g - only 802.11g connections are allowed. If you only have 802.11g, selecting this option may provide a performance improvement over using the default setting.
  • Super 802.11g (108Mbps) - This uses Packet Bursting, FastFrame, and Compression techniques to increase throughput. Only clients supporting the "Atheros Super G" mode can connect at 108Mbps. However, this option is backward-compatible with 802.11ab and (standard) 802.11g.

Setup · Operation

Page 21 of the LevelOne WAP-0005 user manual — Wireless Screens
Page 21 · click to enlarge
Page 21
  • Dynamic Super 802.11g (108Mbps) - This uses Packet Bursting, FastFrame, Compression, and "Channel Bonding" (using 2 channels) to increase throughput. Only clients supporting the "Atheros Super G" mode can connect at 108Mbps, and they will only use this speed when necessary. Howerver, this option is backwardcompatible with 802.11b and (standard) 802.11g.
  • Static Super 802.11g (108Mbps) - This uses Packet Bursting, FastFrame, Compression, and "Channel Bonding" (using 2 channels) to increase thoughput. Because "Channel Bonding" is always used, this method is NOT compatible with 802.11b and (standard) 802.11g. Only clients supporting the "Atheros Super G" mode can connect at 108Mbps; they will always connect at this speed. Select this only if all wireless stations support this "Atheros Super G" mode.

Operating Mode Select the desired mode:

  • Wireless Access Point - operate as a normal Access Point
  • Client Access Point - act as a client for another Access Point. If selected, you must provide the address (MAC address) of the other Access Point (Remote AP).
  • Repeater Access Point - act as a repeater for another Access Point. If selected, you must provide the address (MAC address) of the other Access Point (Remote AP).
  • Point-to-Point Bridge - In this mode, the AP will communicate ONLY with another Bridge-mode Wireless Station. You must enter the MAC address (physical address) of the other Bridge-mode Wireless Station in the field provided. WEP can (and should) be used to protect this communication.
  • Point-to-Multi-Point Bridge - Select this only if this AP is the "Master" for a group of Bridge-mode Wireless Stations. The other Bridge-mode Wireless Stations must be set to Point-to-Point Bridge mode, using this AP's MAC address. They then send all traffic to this "Master", rather than communicate directly with each other. WEP can (and should) be used to protect this traffic.

Remote AP MAC Address

This is not required unless the Operating Mode is Client Access Point, Repeater Access Point, or Point-to-Point Bridge. In these modes, you must provide the MAC address of the other AP in this field. You can either enter the MAC address directly, or, if the other AP is on- line, you can click the "Select AP" button and select from a list of available APs.

Channel No If "Automatic" is selected, the Wireless Access Point will self-select a Wireless Channel.

If you experience interference (shown by lost connections and/or slow data transfers) you may need to experiment with different channels to see which Channel is the best.

Current Channel No.

This displays the current channel used by the Access Point.

SSID Enter the desired SSID. Wireless Stations must use the same SSID.

Page 22 of the LevelOne WAP-0005 user manual — Wireless Screens
Page 22 · click to enlarge
Page 22

Broadcast SSID If Enabled, the SSID will be broadcast to all Wireless Stations. Sta- tions which have no SSID (or a "null" value) can then adopt the correct SSID for connections to this Access Point.

Setup

Page 23 of the LevelOne WAP-0005 user manual — Security Settings
Page 23 · click to enlarge
Page 23

Security Settings

Select the desired option, and then enter the settings for the selected method.

The available options are:

  • None - No security is used. Anyone using the correct SSID can connect to your network.
  • WEP - The 802.11b standard. Data is encrypted before transmission, but the encryption system is not very strong.
  • WPA-PSK - Like WEP, data is encrypted before transmission. WPA is more secure than WEP, and should be used if possible. The PSK (Pre-shared Key) must be entered on each Wireless station. The 256Bit encryption key is derived from the PSK, and changes frequently.
  • WPA-802.1x - This version of WPA requires a Radius Server on your LAN to provide the client authentication according to the 802.1x standard. Data transmissions are encrypted using the WPA standard. If this option is selected:
  • This Access Point must have a "client login" on the Radius Server.
  • Each user must have a "user login" on the Radius Server.
  • Each user's wireless client must support 802.1x and provide the login data when required.
  • All data transmission is encrypted using the WPA standard. Keys are automatically generated, so no key input is required.
  • 802.1x - This uses the 802.1x standard for client authentication, and WEP for data encryption. If possible, you should use WPA-802.1x instead, because WPA encryption is much stronger than WEP encryption. If this option is selected:
  • This Access Point must have a "client login" on the Radius Server.
  • Each user must have a "user login" on the Radius Server.
  • Each user's wireless client must support 802.1x and provide the login data when required.
  • All data transmission is encrypted using the WEP standard. You only have to select the WEP key size; the WEP key is automatically generated.
Page 24 of the LevelOne WAP-0005 user manual — Using MAC authentication
Page 24 · click to enlarge
Page 24

Security Settings - None

LevelOne WAP-0005 — Security Settings - None diagram (page 24)
Fig. 13 · Security Settings - None
Figure 13Wireless Security - None

No security is used. Anyone using the correct SSID can connect to your network. The only settings available from this screen are Radius MAC Authentication and UAM (Universal Access Method).

Radius MAC Authentication

Radius MAC Authentication provides for MAC address checking which is centralized on your Radius server. If you don't have a Radius Server, you cannot use this feature.

Using MAC authentication

1. Ensure the Wireless Access Point can login to your Radius Server.
  • Add a RADIUS client on the RADIUS server, using the IP address or name of the Wireless Access Point, and the same shared key as entered on the Wireless Access Point.
  • Ensure the Wireless Access Point has the correct address, port number, and shared key for login to your Radius Server. These parameters are entered either on the Security page, or the Radius-based MAC authentication sub-screen, depending on the security method used.
  • On the Access Point, enable the Radius-based MAC authentication feature on the screen below. 2. Add Users on the Radius server as required. The username must be the MAC address of the Wireless client you wish to allow, and the password must be blank. 3. When clients try to associate with the Access Point, their MAC address is passed to the Radius Server for authentication.
  • If successful, “xx:xx:xx:xx:xx:xx MAC authentication” is entered in the log, and client station status would show as “authenticated” on the station list table;
  • If not successful, “xx:xx:xx:xx:xx:xx MAC authentication failed” is entered in the log,, and station status is shown as “authenticating” on the station list table.

Setup

Page 25 of the LevelOne WAP-0005 user manual — Data - Radius-based MAC Authentication Screen
Page 25 · click to enlarge
Page 25

Radius-based MAC authentication Screen

This screen will look different depending on the current security setting. If you have already provided the address of your Radius server, you won't be prompted for it again. Otherwise, you must enter the details of your Radius Server on this screen.

LevelOne WAP-0005 — Radius-based MAC authentication Screen diagram (page 25)
Fig. 14 · Radius-based MAC authentication Screen
Figure 14Radius-based MAC Authentication Screen

Data - Radius-based MAC Authentication Screen

Enable ... Enable this if you wish to Radius-based MAC authentication.

If this field is visible, enter the name or IP address of the Radius Server on your network.

Radius Port If this field is visible, enter the port number used for connections to the Radius Server.

Client Login Name If this field is visible, it displays the name used for the Client Login on the Radius Server. This Login name must be created on the Radius Server.

Shared Key If this field is visible, it is used for the Client Login on the Radius Server. Enter the key value to match the value on the Radius Server.

WEP Key If this field is visible, it is for the WEP key used to encrypt data transmissions to the Radius Server. Enter the desired key value (in HEX), and ensure the Radius Server has the same value.

WEP Key Index If this field is visible, select the desired key index. This sets which of the previously-entered WEP keys will be used for communication with the Radius Server. Any value can be used, provided it matches the value on the Radius Server.

Radius Server Address

Page 26 of the LevelOne WAP-0005 user manual — UAM
Page 26 · click to enlarge
Page 26

UAM

UAM (Universal Access Method) is intended for use in Internet cafes, Hot Spots, and other sites where the Access Point is used to provide Internet Access.

If enabled, then HTTP (TCP, port 80) connections are checked. (UAM only works on HTTP connections; all other traffic is ignored.) If the user has not been authenticated, Internet access is blocked, and the user is re-directed to another web page. Typically, this web page is on your Web server, and explains how to pay and obtain Internet access.

To use UAM, you need a Radius Server for Authentication. The "Radius Server Setup" must be completed before you can use UAM. The required setup depends on whether you are using “Internal” or “External” authentication.

  • Internal authentication uses the web page built into the Wireless Access Point.
  • External authentication uses a web page on your Web server. Generally, you should use External authentication, as this allows you to provide relevant and helpful information to users.

UAM authentication - Internal 1. Ensure the Wireless Access Point can login to your Radius Server.

  • Add a RADIUS client on RADIUS server, using the IP address or name of the Wireless Access Point, and the same shared key as entered on the Wireless Access Point.
  • Ensure the Wireless Access Point has the correct address, port number, and shared key for login to your Radius Server. These parameters are entered either on the Security page, or the UAM sub-screen, depending on the security method used. 2. Add users on your RADIUS server as required, and allow access by these users. 3. Client PCs must have the correct Wireless settings in order to associate with the Wireles Access Point. 4. When an associated client tries to use HTTP (TCP, port 80) connections, they will be redirected to a user login page. 5. The client (user) must then enter the user name and password, as defined on the Radius Server. (You must provide some system to let users know the correct name and password to use.) 6. If the user name and password is correct, Internet access is allowed. Otherwise, the user remains on the login page.
  • Clients which pass the authentication are listed as “xx:xx:xx:xx:xx:xx WEB authentication” in the log table, and station status would show as “Authenticated” on the station list table.
  • If a client fails authentication, “xx:xx:xx:xx:xx:xx WEB authentication failed” shown in the log, and station status is shown as “authenticating” on the station list table.

UAM authentication – External 1. Ensure the Wireless Access Point can login to your Radius Server.

  • Add a RADIUS client on RADIUS server, using the IP address or name of the Wireless Access Point, and the same shared key as entered on the Wireless Access Point.
  • Ensure the Wireless Access Point has the correct address, port number, and shared key for login to your Radius Server. These parameters are entered either on the Security page, or the UAM sub-screen, depending on the security method used. 2. On your Web Server, create a suitable login page. The login page must have a link or button to allow the user to input their user name and password on the uamlogon.htm page on the Access Point .

Setup

Page 27 of the LevelOne WAP-0005 user manual — Data – UAM Screen
Page 27 · click to enlarge
Page 27

3. On the Access Point’s UAM screen, select External Web-based Authentication, and enter the URL for the login page on your Web server. 4. Add users on your RADIUS server as required, and allow access by these users. 5. Client PCs must have the correct Wireless settings in order to associate with the Wireles Access Point. 6. When an associated client tries to use HTTP (TCP, port 80) connections, they will be re- directed to the login page on your Web Server. They must then click the link or button in order to reach the Access Point’s login page. 7. The client (user) must then enter the user name and password, as defined on the Radius Server. (You must provide some system to let users know the correct name and password to use.) 8. If the user name and password is correct, Internet access is allowed. Otherwise, the user remains on the login page.

  • Clients which pass the authentication are listed as “xx:xx:xx:xx:xx:xx WEB authentication” in the log table, and station status would show as “Authenticated” on the station list table.
  • If a client fails authentication, “xx:xx:xx:xx:xx:xx WEB authentication failed” is shown in the log, and station status is shown as “Authenticating” on the station list table.

UAM Screen

The UAM screen will look different depending on the current security setting. If you have already provided the address of your Radius server, you won't be prompted for it again.

LevelOne WAP-0005 — UAM Screen diagram (page 27)
Fig. 15 · UAM Screen
Figure 15UAM Screen

Data – UAM Screen

Enable Enable this if you wish to use this feature.

If selected, then when a user first tries to access the Internet, they will be blocked, and re-directed to the built-in login page. The logon data is then sent to the Radius Server for authentication.

Internal Web-based Authentication

Page 28 of the LevelOne WAP-0005 user manual — Data - WEP Screen
Page 28 · click to enlarge
Page 28

If selected, then when a user first tries to access the Internet, they will be blocked, and re-directed to the URL below. This needs to be on your own local Web Server. The page must also link back to the built- in login page on this device to complete the login procedure.

Login URL Enter the URL of the page on your local Web Server you wish users to see when they attempt to access the Internet, but are not logged in.

Enter the URL of the page on your local Web Server you wish users to see if their login fails. (This may be the same URL as the Login URL).

Security Settings - WEP

This is the 802.11b standard. Data is encrypted before transmission, but the encryption system is not very strong.

LevelOne WAP-0005 — Security Settings - WEP diagram (page 28)
Fig. 16 · Security Settings - WEP
Figure 16WEP Wireless Security

Data - WEP Screen

WEP

Select the desired option, and ensure your Wireless stations have the same setting:

  • 64 Bit Encryption - Keys are 10 Hex (5 ASCII) characters.
  • 128 Bit Encryption - Keys are 26 Hex (13 ASCII) characters.
Show 4 more labels / short text on this page
Setup · External Web-based Authentication · Login Failure URL · Data Encryption
Page 29 of the LevelOne WAP-0005 user manual — Security Settings
Page 29 · click to enlarge
Page 29

Authentication Normally, you can leave this at “Automatic”, so that Wireless Stations can use either method ("Open System" or "Shared Key".).

If you wish to use a particular method, select the appropriate value - "Open System" or "Shared Key". All Wireless stations must then be set to use the same method.

Key Input Select "Hex" or "ASCII" depending on your input method. (All keys are converted to Hex, ASCII input is only for convenience.)

Key Value Enter the key values you wish to use. The default key, selected by the radio button, is required. The other keys are optional. Other stations must have matching key values.

Passphrase Use this to generate a key or keys, instead of entering them directly. Enter a word or group of printable characters in the Passphrase box and click the "Generate Key" button to automatically configure the WEP Key(s). If encryption strength is set to 64 bit, then each of the four key fields will be populated with key values. If encryption strength is set to 128 bit, then only the selected WEP key field will be given a key value.

The current status is displayed.

Click the "Configure" button to configure this feature if required.

See page 21 for details on using Radius MAC authentication.

UAM The current status is displayed.

Click the "Configure" button to configure this feature if required.

See page 23 for details on using UAM.

Radius MAC Authentication

Page 30 of the LevelOne WAP-0005 user manual — Data - WPA-PSK Screen
Page 30 · click to enlarge
Page 30

Security Settings - WPA-PSK

Like WEP, data is encrypted before transmission. WPA is more secure than WEP, and should be used if possible. The PSK (Pre-shared Key) must be entered on each Wireless station. The 256Bit encryption key is derived from the PSK, and changes frequently.

LevelOne WAP-0005 — Security Settings - WPA-PSK diagram (page 30)
Fig. 17 · Security Settings - WPA-PSK
Figure 17WPA-PSK Wireless Security

Data - WPA-PSK Screen

WPA-PSK

Network Key Enter the key value. Data is encrypted using a 256Bit key derived from this key. Other Wireless Stations must use the same key.

WPA Encryption Select the desired option. Other Wireless Stations must use the same method.

  • TKIP - Unicast (point-to-point) transmissions are encrypted using TKIP, and multicast (broadcast) transmissions are not encrypted.
  • TKIP + 64 bit WEP - Unicast (point-to-point) transmissions are encrypted using TKIP, and multicast (broadcast) transmissions are encrypted using 64 bit WEP.
  • TKIP + 128 bit WEP - Unicast (point-to-point) transmissions are encrypted using TKIP, and multicast (broadcast) transmissions are encrypted using 128 bit WEP.
  • AES - CCMP - CCMP is the most common sub-type of AES (Advanced Encryption System). Most systems will simply say "AES". If selected, both Unicast (point-to-point) and multicast (broadcast) transmissions are encrypted using AES.

Setup

Page 31 of the LevelOne WAP-0005 user manual — Security Settings
Page 31 · click to enlarge
Page 31

Pairwise Key Update This refers to the key used for point-to-point transmissions. Enable this if you want the keys to be updated regularly.

Key Lifetime This field determines how often Pairwise keys are dynamically updated. Enter the desired value.

Group Key Update This refers to the key used for broadcast transmissions. Enable this if you want the keys to be updated regularly.

Key Lifetime This field determines how often the Group key is dynamically updated. Enter the desired value.

Update Group key when any membership terminates

If enabled, the Group key will be updated whenever any mem- ber leaves the group or disassociates from the Access Point.

The current status is displayed.

Click the "Configure" button to configure this feature if re- quired.

See page 21 for details on using Radius MAC authentication.

UAM The current status is displayed.

Click the "Configure" button to configure this feature if re- quired.

See page 23 for details on using UAM.

Radius MAC Authentication

Page 32 of the LevelOne WAP-0005 user manual — Data - WPA-802.1x Screen
Page 32 · click to enlarge
Page 32

Security Settings - WPA-802.1x

This version of WPA requires a Radius Server on your LAN to provide the client authentica- tion according to the 802.1x standard. Data transmissions are encrypted using the WPA standard.

If this option is selected:

  • This Access Point must have a "client login" on the Radius Server.
  • Each user must have a "user login" on the Radius Server.
  • Each user's wireless client must support 802.1x and provide the login data when required.
  • All data transmission is encrypted using the WPA standard. Keys are automatically generated, so no key input is required.
LevelOne WAP-0005 — Security Settings - WPA-802.1x diagram (page 32)
Fig. 18 · Security Settings - WPA-802.1x
Figure 18WPA-802.1x Wireless Security

Data - WPA-802.1x Screen

WPA-802.1x

Enter the name or IP address of the Radius Server on your network.

Radius Port Enter the port number used for connections to the Radius Server.

Setup · Radius Server Address

Page 33 of the LevelOne WAP-0005 user manual — Security Settings
Page 33 · click to enlarge
Page 33

Client Login Name This read-only field displays the current login name, which is the same as the name of the Access Point. The Radius Server must be configured to accept this login.

Shared Key This is used for the Client Login on the Radius Server. Enter the key value to match the Radius Server.

WPA Encryption Select the desired option. Other Wireless Stations must use the same method.

  • TKIP - Unicast (point-to-point) transmissions are encrypted using TKIP, and multicast (broadcast) transmissions are not encrypted.
  • TKIP + 64 bit WEP - Unicast (point-to-point) transmissions are encrypted using TKIP, and multicast (broadcast) transmissions are encrypted using 64 bit WEP.
  • TKIP + 128 bit WEP - Unicast (point-to-point) transmissions are encrypted using TKIP, and multicast (broadcast) transmissions are encrypted using 128 bit WEP.
  • AES - CCMP - CCMP is the most common sub-type of AES (Advanced Encryption System). Most systems will simply say "AES". If selected, both Unicast (point-to-point) and multicast (broadcast) transmissions are encrypted using AES.

This refers to the key used for point-to-point transmissions. Enable this if you want the keys to be updated regularly.

Key Lifetime This field determines how often Pairwise keys are dynamically updated. Enter the desired value.

Group Key Update This refers to the key used for broadcast transmissions. Enable this if you want the keys to be updated regularly.

Key Lifetime This field determines how often the Group key is dynamically updated. Enter the desired value.

Update Group key when any member- ship terminates

If enabled, the Group key will be updated whenever any member leaves the group or disassociates from the Access Point.

Radius Accounting Enable this if you want this Access Point to send accounting data to the Radius Server.

If enabled, the port used by your Radius Server must be entered in the Radius Accounting Port" field.

Update Report every ...

If Radius accounting is enabled, you can enable this and enter the desired update interval. This Access Point will then send updates according to the specified time period.

The current status is displayed.

Click the "Configure" button to configure this feature if required.

See page 21 for details on using Radius MAC authentication.

UAM The current status is displayed.

Click the "Configure" button to configure this feature if required.

See page 23 for details on using UAM.

Pairwise Key Update · Radius MAC Authentication

Page 34 of the LevelOne WAP-0005 user manual — Data - 802.1x Screen
Page 34 · click to enlarge
Page 34

Security Settings - 802.1x

This uses the 802.1x standard for client authentication, and WEP for data encryption. If possi- ble, you should use WPA-802.1x instead, because WPA encryption is much stronger than WEP encryption.

If this option is selected:

  • This Access Point must have a "client login" on the Radius Server.
  • Each user must have a "user login" on the Radius Server.
  • Each user's wireless client must support 802.1x and provide the login data when required.
  • All data transmission is encrypted using the WEP standard. You only have to select the WEP key size; the WEP key is automatically generated.
LevelOne WAP-0005 — Security Settings - 802.1x diagram (page 34)
Fig. 19 · Security Settings - 802.1x
Figure 19802.1x Wireless Security

Data - 802.1x Screen

Radius Server Address Enter the name or IP address of the Radius Server on your network.

Radius Port Enter the port number used for connections to the Radius Server.

Client Login Name This read-only field displays the current login name, which is the same as the name of the Access Point. The Radius Server must be configured to accept this login.

Setup

Page 35 of the LevelOne WAP-0005 user manual — Security Settings
Page 35 · click to enlarge
Page 35

Shared Key This is used for the Client Login on the Radius Server. Enter the key value to match the Radius Server.

WEP Key Size Select the desired option:

  • 64 Bit - Key size is 64Bits. The keys are automatically generated, and do not need to be entered.
  • 128 Bit - Key size is 128Bits. The keys are automatically generated, and do not need to be entered.

Key Exchange Enable this if you want the keys to be updated regularly.

Key Lifetime This field determines how often keys are dynamically updated. Enter the desired value.

Radius Accounting Enable this if you want this Access Point to send accounting data to the Radius Server.

If enabled, the port used by your Radius Server must be entered in the Radius Accounting Port" field.

Update Report every ... If Radius accounting is enabled, you can enable this and enter the desired update interval. This Access Point will then send updates according to the specified time period.

The current status is displayed.

Click the "Configure" button to configure this feature if re- quired.

See page 21 for details on using Radius MAC authentication.

UAM The current status is displayed.

Click the "Configure" button to configure this feature if re- quired.

See page 23 for details on using UAM.

Radius MAC Authentication

Page 36 of the LevelOne WAP-0005 user manual — Data - Advanced Settings Screen
Page 36 · click to enlarge
Page 36

Advanced Settings

Clicking the Advanced link on the menu will result in a screen like the following.

LevelOne WAP-0005 — Advanced Settings diagram (page 36)
Fig. 20 · Advanced Settings
Figure 20Advanced Settings

Data - Advanced Settings Screen

Basic Rate Selection The Basic Rate is used for broadcasting. It does not determine the data transmission rate, which is determined by the "Mode" setting on the Basic screen. Select the desired option.

Do NOT select the "802.11g" or "OFDM" options unless ALL of your wireless clients support this. 802.11b clients will not be able to connect to the Access Point if either of these modes is selected.

Wireless Separation If enabled, then each Wireless station using the Access Point is invisible to other Wireless stations. In most business situations, this setting should be Disabled.

Worldwide Mode (802.11d)

Enable this setting if you wish to use this mode, and your Wireless stations support this mode.

Setup · Basic Rate · Options

Page 37 of the LevelOne WAP-0005 user manual — Advanced Settings
Page 37 · click to enlarge
Page 37

Disassociated Timeout This determines how quickly a Wireless Station will be consid- ered "Disassociated" with this AP, when no traffic is received. Enter the desired time period.

Fragmentation Enter the preferred setting between 256 and 2346.

Beacon Interval Enter the preferred setting between 0 and 3000.

RTS/CTS Threshold Enter the preferred setting between 256 and 2346.

Preamble Type Select the desired preamble type.

Output Power Level Select the desired power output. Higher levels will give a greater range, but are also more likely to cause interference with other devices.

Antenna Selection If your Access Point has only 1 antenna, there is only 1 option available. If your Access Point has 2 antennae, select the option which gives the best results in your location.

802.11b (2.4GHz only)

Protection Type Select the desired option.

Short Slot Time Enable or disable this setting as required.

Protection Mode Normally, this should be left at "Auto".

Protection Rate Select the desired option.

Parameters

Page 38 of the LevelOne WAP-0005 user manual — Using WEP
Page 38 · click to enlarge
Page 38

Chapter 4 PC and Server Configuration

This Chapter details the PC Configuration required for each PC on the local LAN.

Overview

All Wireless Stations need to have settings which match the Wireless Access Point. These settings depend on the mode in which the Access Point is being used.

  • If using WEP or WPA-PSK, it is only necessary to ensure that each Wireless station's settings match those of the Wireless Access Point, as described below.
  • For WPA-802.1x and 802.1x modes, configuration is much more complex. The Radius Server must be configured correctly, and setup of each Wireless station is also more complex.

Using WEP

For each of the following items, each Wireless Station must have the same settings as the Wireless Access Point.

Mode On each PC, the mode must be set to Infrastructure.

SSID (ESSID) This must match the value used on the Wireless Access Point.

The default value is wireless

  • Each Wireless station must be set to use WEP data encryption.
  • The Key size (64 bit or 128 bit) must be set to match the Access Point.
  • The keys values on the PC must match the key values on the Access Point.

On some systems, the "64 bit" key is shown as "40 bit" and "128 bit" is shown as "104 bit". This difference arises because the key input by the user is 24 bits less than the key size used for encryption.

Wireless Security

Page 39 of the LevelOne WAP-0005 user manual — Using WPA-PSK
Page 39 · click to enlarge
Page 39

Using WPA-PSK

For each of the following items, each Wireless Station must have the same settings as the Wireless Access Point.

Mode On each PC, the mode must be set to Infrastructure.

SSID (ESSID) This must match the value used on the Wireless Access Point.

The default value is wireless

On each client, Wireless security must be set to WPA-PSK.

  • The Pre-shared Key entered on the Access Point must also be entered on each Wireless client.
  • The Encryption method (e.g. TKIP, AES) must be set to match the Access Point.

Wireless Security

Page 40 of the LevelOne WAP-0005 user manual — Radius Server Configuration
Page 40 · click to enlarge
Page 40

PC and Server Configuration

Using WPA-802.1x

This is the most secure and most complex system.

802.1x mode provides greater security and centralized management, but it is more complex to configure.

Wireless Station Configuration

For each of the following items, each Wireless Station must have the same settings as the Wireless Access Point.

Mode On each PC, the mode must be set to Infrastructure.

SSID (ESSID) This must match the value used on the Wireless Access Point.

The default value is wireless

802.1x Authentication

Each client must obtain a Certificate which is used for authentication for the Radius Server.

802.1x Encryption

Typically, EAP-TLS is used. This is a dynamic key system, so keys do NOT have to be entered on each Wireless station.

Radius Server Configuration

If using WPA-802.1x mode, the Radius Server on your network must be configured as follow:

  • It must provide and accept Certificates for user authentication.
  • There must be a Client Login for the Wireless Access Point itself.
  • The Wireless Access Point will use its Default Name as its Client Login name.
  • The Shared Key , set on the Security Screen of the Access Point, must match the Shared Secret value on the Radius Server.
  • Encryption settings must be correct.
Page 41 of the LevelOne WAP-0005 user manual — Services Installation
Page 41 · click to enlarge
Page 41

802.1x Server Setup (Windows 2000 Server)

This section describes using Microsoft Internet Authentication Server as the Radius Server, since it is the most common Radius Server available that supports the EAP-TLS authentication method.

The following services on the Windows 2000 Domain Controller (PDC) are also required:

  • dhcpd
  • dns
  • rras
  • webserver (IIS)
  • Radius Server (Internet Authentication Service)
  • Certificate Authority

Windows 2000 Domain Controller Setup

1. Run dcpromo.exe from the command prompt. 2. Follow all of the default prompts, ensure that DNS is installed and enabled during installation.

Services Installation

1. Select the Control Panel - Add/Remove Programs . 2. Click Add/Remove Windows Components from the left side. 3. Ensure that the following components are activated (selected):
  • Certificate Services . After enabling this, you will see a warning that the computer cannot be renamed and joined after installing certificate services. Select Yes to select certificate services and continue
  • World Wide Web Server . Select World Wide Web Server on the Internet Information Services (IIS) component.
  • From the Networking Services category, select Dynamic Host Configuration Protocol (DHCP), and Internet Authentication Service (DNS should already be selected and installed).
Page 42 of the LevelOne WAP-0005 user manual — 802.1x Server Setup (Windows 2000 Server)
Page 42 · click to enlarge
Page 42

PC and Server Configuration

LevelOne WAP-0005 — 802.1x Server Setup (Windows 2000 Server) diagram (page 42)
Fig. 21 · 802.1x Server Setup (Windows 2000 Server)
Figure 21Components Screen
4. Click Next . 5. Select the Enterprise root CA , and click Next .
LevelOne WAP-0005 — 802.1x Server Setup (Windows 2000 Server) diagram (page 42)
Fig. 22 · 802.1x Server Setup (Windows 2000 Server)
Figure 22Certification Screen
6. Enter the information for the Certificate Authority, and click Next .
Page 43 of the LevelOne WAP-0005 user manual — DHCP server configuration
Page 43 · click to enlarge
Page 43
LevelOne WAP-0005 — 802.1x Server Setup (Windows 2000 Server) diagram (page 43)
Fig. 23 · 802.1x Server Setup (Windows 2000 Server)
Figure 23CA Screen
7. Click Next if you don't want to change the CA's configuration data. 8. Installation will warn you that Internet Information Services are running, and must be stopped before continuing. Click Ok , then Finish .

DHCP server configuration

1. Click on the Start - Programs - Administrative Tools - DHCP 2. Right-click on the server entry as shown, and select New Scope .
LevelOne WAP-0005 — DHCP server configuration diagram (page 43)
Fig. 24 · DHCP server configuration
Figure 24DHCP Screen
3. Click Next when the New Scope Wizard Begins. 4. Enter the name and description for the scope, click Next . 5. Define the IP address range. Change the subnet mask if necessary. Click Next .
Page 44 of the LevelOne WAP-0005 user manual — 802.1x Server Setup (Windows 2000 Server)
Page 44 · click to enlarge
Page 44

PC and Server Configuration

LevelOne WAP-0005 — 802.1x Server Setup (Windows 2000 Server) diagram (page 44)
Fig. 25 · 802.1x Server Setup (Windows 2000 Server)

Figure 25:IP Address Screen

6. Add exclusions in the address fields if required. If no exclusions are required, leave it blank. Click Next. 7. Change the Lease Duration time if preferred. Click Next. 8. Select Yes, I want to configure these options now, and click Next. 9. Enter the router address for the current subnet. The router address may be left blank if there is no router. Click Next. 10. For the Parent domain, enter the domain you specified for the domain controller setup, and enter the server's address for the IP address. Click Next.

LevelOne WAP-0005 — 802.1x Server Setup (Windows 2000 Server) diagram (page 44)
Fig. 26 · 802.1x Server Setup (Windows 2000 Server)
Figure 26DNS Screen
11. If you don't want a WINS server, just click Next . 12. Select Yes, I want to activate this scope now . Click Next , then Finish . 13. Right-click on the server, and select Authorize . It may take a few minutes to complete.
Page 45 of the LevelOne WAP-0005 user manual — Certificate Authority Setup
Page 45 · click to enlarge
Page 45

Certificate Authority Setup

1. Select Start - Programs - Administrative Tools - Certification Authority . 2. Right-click Policy Settings , and select New - Certificate to Issue .
LevelOne WAP-0005 — Certificate Authority Setup diagram (page 45)
Fig. 27 · Certificate Authority Setup
Figure 27Certificate Authority Screen
3. Select Authenticated Session and Smartcard Logon (select more than one by holding down the Ctrl key). Click OK .
LevelOne WAP-0005 — Certificate Authority Setup diagram (page 45)
Fig. 28 · Certificate Authority Setup
Figure 28Template Screen
4. Select Start - Programs - Administrative Tools - Active Directory Users and Computers . 5. Right-click on your active directory domain, and select Properties.
Page 46 of the LevelOne WAP-0005 user manual — 802.1x Server Setup (Windows 2000 Server)
Page 46 · click to enlarge
Page 46

PC and Server Configuration

LevelOne WAP-0005 — 802.1x Server Setup (Windows 2000 Server) diagram (page 46)
Fig. 29 · 802.1x Server Setup (Windows 2000 Server)
Figure 29Active Directory Screen
6. Select the Group Policy tab, choose Default Domain Policy then click Edit .
LevelOne WAP-0005 — 802.1x Server Setup (Windows 2000 Server) diagram (page 46)
Fig. 30 · 802.1x Server Setup (Windows 2000 Server)
Figure 30Group Policy Tab
7. Select Computer Configuration - Windows Settings - Security Settings - Public Key Policies , right-click Automatic Certificate Request Settings - New - Automatic Certificate Request .
Page 47 of the LevelOne WAP-0005 user manual — 802.1x Server Setup (Windows 2000 Server)
Page 47 · click to enlarge
Page 47
LevelOne WAP-0005 — 802.1x Server Setup (Windows 2000 Server) diagram (page 47)
Fig. 31 · 802.1x Server Setup (Windows 2000 Server)
Figure 31Group Policy Screen
8. When the Certificate Request Wizard appears, click Next . 9. Select Computer , then click Next .
LevelOne WAP-0005 — 802.1x Server Setup (Windows 2000 Server) diagram (page 47)
Fig. 32 · 802.1x Server Setup (Windows 2000 Server)
Figure 32Certificate Template Screen
10. Ensure that your certificate authority is checked, then click Next . 11. Review the policy change information and click Finish . 12. Click Start - Run , type cmd and press enter. Enter secedit /refreshpolicy machine_policy This command may take a few minutes to take effect.
Page 48 of the LevelOne WAP-0005 user manual — Internet Authentication Service (Radius) Setup
Page 48 · click to enlarge
Page 48

PC and Server Configuration

Internet Authentication Service (Radius) Setup

1. Select Start - Programs - Administrative Tools - Internet Authentication Service 2. Right-click on Clients , and select New Client .
LevelOne WAP-0005 — Internet Authentication Service (Radius) Setup diagram (page 48)
Fig. 33 · Internet Authentication Service (Radius) Setup
Figure 33Service Screen
3. Enter a name for the access point, click Next . 4. Enter the address or name of the Wireless Access Point, and set the shared secret, as entered on the Security Settings of the Wireless Access Point. 5. Click Finish . 6. Right-click on Remote Access Policies , select New Remote Access Policy . 7. Assuming you are using EAP-TLS, name the policy eap-tls , and click Next .
8. Click Add... If you don't want to set any restrictions and a condition is required, select Day-And-TimeRestrictions , and click Add...
LevelOne WAP-0005 — Internet Authentication Service (Radius) Setup diagram (page 48)
Fig. 34 · Internet Authentication Service (Radius) Setup
Figure 34Attribute Screen
9. Click Permitted , then OK . Select Next . 10. Select Grant remote access permission . Click Next .
Page 49 of the LevelOne WAP-0005 user manual — 802.1x Server Setup (Windows 2000 Server)
Page 49 · click to enlarge
Page 49
11. Click Edit Profile... and select the Authentication tab. Enable Extensible Authentication Protocol , and select Smart Card or other Certificate . Deselect other authentication methods listed. Click OK .
LevelOne WAP-0005 — 802.1x Server Setup (Windows 2000 Server) diagram (page 49)
Fig. 35 · 802.1x Server Setup (Windows 2000 Server)
Figure 35Authentication Screen
12. Select No if you don't want to view the help for EAP. Click Finish .
Page 50 of the LevelOne WAP-0005 user manual — Remote Access Login for Users
Page 50 · click to enlarge
Page 50

PC and Server Configuration

Remote Access Login for Users

1. Select Start - Programs - Administrative Tools - Active Directory Users and Computers . 2. Double click on the user who you want to enable. 3. Select the Dial-in tab, and enable Allow access . Click OK .
LevelOne WAP-0005 — Remote Access Login for Users diagram (page 50)
Fig. 36 · Remote Access Login for Users
Figure 36Dial-in Screen
Page 51 of the LevelOne WAP-0005 user manual — Client Certificate Setup
Page 51 · click to enlarge
Page 51

802.1x Client Setup on Windows XP

Windows XP ships with a complete 802.1x client implementation. If using Windows 2000, you can install SP3 (Service Pack 3) to gain the same functionality.

If you don't have either of these systems, you must use the 802.1x client software provided with your wireless adapter. Refer to your vendor's documentation for setup instructions.

The following instructions assume that:

  • You are using Windows XP
  • You are connecting to a Windows 2000 server for authentication.
  • You already have a login (User name and password) on the Windows 2000 server.

Client Certificate Setup

1. Connect to a network which doesn't require port authentication. 2. Start your Web Browser. In the Address box, enter the IP address of the Windows 2000 Server, followed by / certsrv e.g http://192.168.0.2/certsrv
3. You will be prompted for a user name and password. Enter the User name and Password assigned to you by your network administrator, and click OK .
LevelOne WAP-0005 — Client Certificate Setup diagram (page 51)
Fig. 37 · Client Certificate Setup
Figure 37Connect Screen
4. On the first screen (below), select Request a certificate , click Next .
Page 52 of the LevelOne WAP-0005 user manual — 802.1x Client Setup on Windows XP
Page 52 · click to enlarge
Page 52

PC and Server Configuration

LevelOne WAP-0005 — 802.1x Client Setup on Windows XP diagram (page 52)
Fig. 38 · 802.1x Client Setup on Windows XP
Figure 38Wireless CA Screen
5. Select User certificate request and select User Certificate , the click Next .
LevelOne WAP-0005 — 802.1x Client Setup on Windows XP diagram (page 52)
Fig. 39 · 802.1x Client Setup on Windows XP
Figure 39Request Type Screen
6. Click Submit .
Page 53 of the LevelOne WAP-0005 user manual — 802.1x Client Setup on Windows XP
Page 53 · click to enlarge
Page 53
LevelOne WAP-0005 — 802.1x Client Setup on Windows XP diagram (page 53)
Fig. 40 · 802.1x Client Setup on Windows XP
Figure 40Identifying Information Screen
7. A message will be displayed, then the certificate will be returned to you. Click Install this certificate .
LevelOne WAP-0005 — 802.1x Client Setup on Windows XP diagram (page 53)
Fig. 41 · 802.1x Client Setup on Windows XP

Figure 41:Certificate Issued Screen

8.. You will receive a confirmation message. Click Yes .
Page 54 of the LevelOne WAP-0005 user manual — Encryption Settings
Page 54 · click to enlarge
Page 54

PC and Server Configuration

LevelOne WAP-0005 — 802.1x Client Setup on Windows XP diagram (page 54)
Fig. 42 · 802.1x Client Setup on Windows XP
Figure 42Root Certificate Screen
9. Certificate setup is now complete.

802.1x Authentication Setup

1. Open the properties for the wireless connection, by selecting Start - Control Panel - Network Connections. 2. Right Click on the Wireless Network Connection , and select Properties . 3. Select the Authentication Tab, and ensure that Enable network access control using IEEE 802.1X is selected, and Smart Card or other Certificate is selected from the EAP type.
LevelOne WAP-0005 — 802.1x Authentication Setup diagram (page 54)
Fig. 43 · 802.1x Authentication Setup
Figure 43Authentication Tab

Encryption Settings

The Encryption settings must match the APs (Access Points) on the Wireless network you wish to join.

  • Windows XP will detect any available Wireless networks, and allow you to configure each network independently.
Page 55 of the LevelOne WAP-0005 user manual — Enabling Encryption
Page 55 · click to enlarge
Page 55
  • Your network administrator can advise you of the correct settings for each network. 802.1x networks typically use EAP-TLS. This is a dynamic key system, so there is no need to enter key values.

Enabling Encryption

To enable encryption for a wireless network, follow this procedure: 1. Click on the Wireless Networks tab.

LevelOne WAP-0005 — Enabling Encryption diagram (page 55)
Fig. 44 · Enabling Encryption
Figure 44Wireless Networks Screen
2. Select the wireless network from the Available Networks list, and click Configure . 3. Select and enter the correct values, as advised by your Network Administrator. For example, to use EAP-TLS, you would enable Data encryption , and click the checkbox for the setting The key is provided for me automatically , as shown below.
Page 56 of the LevelOne WAP-0005 user manual — 802.1x Client Setup on Windows XP
Page 56 · click to enlarge
Page 56

PC and Server Configuration

LevelOne WAP-0005 — 802.1x Client Setup on Windows XP diagram (page 56)
Fig. 45 · 802.1x Client Setup on Windows XP
Figure 45Properties Screen

Setup for Windows XP and 802.1x client is now complete.

Page 57 of the LevelOne WAP-0005 user manual — Using 802.1x Mode (without WPA)
Page 57 · click to enlarge
Page 57

Using 802.1x Mode (without WPA)

This is very similar to using WPA-802.1x.

The only difference is that on your client, you must NOT enable the setting The key is pro- vided for me automatically.

Instead, you must enter the WEP key manually, ensuring it matches the WEP key used on the Access Point.

LevelOne WAP-0005 — Using 802.1x Mode (without WPA) diagram (page 57)
Fig. 46 · Using 802.1x Mode (without WPA)
Figure 46Properties Screen

On some systems, the "64 bit" WEP key is shown as "40 bit" and the "128 bit" WEP key is shown as "104 bit". This difference arises because the key input by the user is 24 bits less than the key size used for encryption.

Page 58 of the LevelOne WAP-0005 user manual — Status Screen
Page 58 · click to enlarge
Page 58

Chapter 5 Operation and Status

This Chapter details the operation of the Wireless Access Point and the status screens.

Operation

Once both the Wireless Access Point and the PCs are configured, operation is automatic.

However, you may need to perform the following operations on a regular basis.

  • If using the Access Control feature, update the Trusted PC database as required. (See Access Control in Chapter 3 for details.)
  • If using 802.1x mode, update the User Login data on the Windows 2000 Server, and configure the client PCs, as required.

Status Screen

Use the Status link on the main menu to view this screen.

Figure 47Status Screen
Page 59 of the LevelOne WAP-0005 user manual — TCP/IP
Page 59 · click to enlarge
Page 59

Data - Status Screen

Access Point Name The current name will be displayed.

MAC Address The MAC (physical) address of the Wireless Access Point.

Domain The region or domain, as selected on the Basic Wireless screen.

Firmware Version The version of the firmware currently installed.

TCP/IP

IP Address The IP Address of the Wireless Access Point.

Subnet Mask The Network Mask (Subnet Mask) for the IP Address above.

Gateway Enter the Gateway for the LAN segment to which the Wireless Access Point is attached (the same value as the PCs on that LAN segment).

DHCP Client This indicates whether the current IP address was obtained from a DHCP Server on your network.

It will display "Enabled" or "Disabled".

SSID The current SSID.

Channel/Frequency The Channel currently in use is displayed.

Mode The current operational mode is displayed.

Authentication This displays the current Authentication setting.

Encryption This displays the current Encryption setting.

Access Control This indicates whether or not the MAC-level "Access Control" feature is enabled.

Log Click this to open a sub-window where you can view the activity log.

Stations Click this to open a sub-window where you can view the list of all current Wireless Stations using the Access Point.

Statistics Click this to open a sub-window where you can view Statistics on data transmitted or received by the Access Point.

Show 4 more labels / short text on this page
Access Point · Wireless · Security · Buttons
Page 60 of the LevelOne WAP-0005 user manual — Data - Activity Log
Page 60 · click to enlarge
Page 60

Activity Log

This screen is displayed when the Log button on the Status screen is clicked.

LevelOne WAP-0005 — Activity Log diagram (page 60)
Fig. 47 · Activity Log
Figure 48Activity Log Screen

Data - Activity Log

Current Time The system date and time is displayed.

Log The Log shows details of the existing connections to the Wireless Access Point.

Refresh Update the data on screen.

Save to file Save the log to a file on your pc.

Clear Log This will delete all data currently in the Log. This will make it easier to read new messages.

Operation and Status · Data · Buttons

Page 61 of the LevelOne WAP-0005 user manual — Data - Station List Screen
Page 61 · click to enlarge
Page 61

Station List

This screen is displayed when the Stations button on the Status screen is clicked.

LevelOne WAP-0005 — Station List diagram (page 61)
Fig. 48 · Station List

Figure 49 Station List Screen

Data - Station List Screen

MAC Address The MAC (physical) address of each Wireless Station is displayed.

Mode The mode of each Wireless Station.

Status The current status of each Wireless Station is displayed.

Refresh Button Update the data on screen.

Station List

Page 62 of the LevelOne WAP-0005 user manual — Data - Statistics Screen
Page 62 · click to enlarge
Page 62

Statistics Screen

This screen is displayed when the 2.4GHz Statistics button on the Status screen is clicked. It shows details of the traffic flowing through the Wireless Access Point.

LevelOne WAP-0005 — Statistics Screen diagram (page 62)
Fig. 49 · Statistics Screen
Figure 50Statistics Screen

Data - Statistics Screen

System Up Time This indicates how long the system has been running since the last restart or reboot.

2.4GHz Wireless

Authentication The number of "Authentication" packets received. Authentication is the process of identification between the AP and the client.

Deauthentication The number of "Deauthentication" packets received. Deauthentica- tion is the process of ending an existing authentication relationship.

Association The number of "Association" packets received. Association creates a connection between the AP and the client. Usually, clients associ- ate with only one (1) AP at any time.

Disassociation The number of "Disassociation" packets received. Disassociation breaks the existing connection between the AP and the client.

Reassociation The number of "Reassociation" packets received. Reassociation is the service that enables an established association (between AP and client) to be transferred from one AP to another (or the same) AP.

MSDU Number of valid Data packets transmitted to or received from Wireless Stations, at application level.

Data Number of valid Data packets transmitted to or received from Wireless Stations, at driver level.

Multicast Packets Number of Broadcast packets transmitted to or received from Wireless Stations, using Multicast transmission.

Operation and Status · System Up Time · Wireless

Page 63 of the LevelOne WAP-0005 user manual — Chapter 5 Operation and Status
Page 63 · click to enlarge
Page 63

Management Number of Management packets transmitted to or received from Wireless Stations.

Control Number of Control packets transmitted to or received from Wire- less Stations.

Page 64 of the LevelOne WAP-0005 user manual — Data - Admin Login Screen
Page 64 · click to enlarge
Page 64

Chapter 6 Other Settings & Features

This Chapter explains when and how to use the Wireless Access Point's "Management" Features.

Overview

This Chapter covers the following features, available on the Wireless Access Point’s Man- agement menu.

  • Admin Login
  • Config File
  • Upgrade Firmware Admin Login Screen

The Admin Login screen allows you to assign a password to the Wireless Access Point. This password limits access to the configuration interface. The default password is password. It is recommended that this be changed, using this screen.

LevelOne WAP-0005 — Overview diagram (page 64)
Fig. 50 · Overview
Figure 51Admin Login Screen

Data - Admin Login Screen

User Name Enter the user name here

New Password Enter the new password here

Repeat New Password Re-enter the new password in this field.

You will be prompted for the password when you connect, as shown below.

Page 65 of the LevelOne WAP-0005 user manual — Chapter 6 Other Settings & Features
Page 65 · click to enlarge
Page 65
Figure 52Password Dialog

Enter the User Name and Password, as set on the Admin Login screen above.

Page 66 of the LevelOne WAP-0005 user manual — Data - Config File Screen
Page 66 · click to enlarge
Page 66

Other Settings & Features

Config File

This screen allows you to Backup (download) the configuration file, and to restore (upload) a previously-saved configuration file.

You can also set the Wireless Access Point back to its factory default settings.

To reach this screen, select Config File in the Management section of the menu.

LevelOne WAP-0005 — Config File diagram (page 66)
Fig. 51 · Config File
Figure 53Config File Screen

Data - Config File Screen

Save a copy of cur- rent settings

Click the Backup button to download the current settings to a file on your PC.

Restore saved settings from a file

If you have a previously-saved configuration file, you can use this to restore those settings by uploading the file. 1. Click the Browse button and navigate to the location of the configuration file. 2. Select the upgrade file. Its name will appear in the File field. 3. Click the Restore button to commence the upload. 4. The Wireless Access Point will need to restart, and will be unavailable during the restart. All exiting connections will be broken.

Revert to factory default settings

Use this to set the Wireless Access Point back to its factory default settings.

  • Click Set to Defaults to start the procedure.
  • The Wireless Access Point will need to restart, and will be unavailable during the restart. All exiting connections will be broken.

Backup · Restore · Defaults

Page 67 of the LevelOne WAP-0005 user manual — Data - SNMP Screen
Page 67 · click to enlarge
Page 67

SNMP

SNMP (Simple Network Management Protocol) is only useful if you have a SNMP program on your PC. To reach this screen, select SNMP in the Management section of the menu.

LevelOne WAP-0005 — SNMP diagram (page 67)
Fig. 52
Figure 54SNMP Screen

Data - SNMP Screen

Enable SNMP Use this to enable or disable SNMP as required

Community Enter the community string, usually either "Public" or "Private".

Access Rights Select the desired option: • Read-only - Data can be read, but not changed.

  • Read/Write - Data can be read, and setting changed.

Any Station The IP address of the manager station is not checked.

Only this station The IP address is checked, and must match the address you enter in the IP address field provided.

If selected, you must enter the IP address of the required station.

Disable Traps are not used.

Broadcast Select this to have Traps broadcast on your network. This makes them available to any PC.

Send to Select this to have Trap messages sent to the specified PC only. If selected, you must enter the IP Address of the desired PC.

Trap version Select the desired option, as supported by your SNMP Management program.

General · Managers · Traps

Page 68 of the LevelOne WAP-0005 user manual — To perform the Firmware Upgrade:
Page 68 · click to enlarge
Page 68

Other Settings & Features

Firmware Upgrade

The firmware (software) in the Wireless Access Point can be upgraded using your Web Browser.

You must first download the upgrade file, and then select Upgrade Firmware in the Manage- ment section of the menu. You will see a screen like the following.

LevelOne WAP-0005 — Firmware Upgrade diagram (page 68)
Fig. 53 · Firmware Upgrade
Figure 55Firmware Upgrade Screen

To perform the Firmware Upgrade:

1. Click the Browse button and navigate to the location of the upgrade file. 2. Select the upgrade file. Its name will appear in the Upgrade File field. 3. Click the Upgrade button to commence the firmware upgrade.

The Wireless Access Point is unavailable during the upgrade process, and must restart when the up- grade is completed. Any connections to or through the Wireless Access Point will be lost.

Page 69 of the LevelOne WAP-0005 user manual — Wireless Specifications
Page 69 · click to enlarge
Page 69

A

Appendix A Specifications

Wireless Access Point

Hardware Specifications

CPU AR2312

DRAM 8 Mbytes (Expand to 64MB)

Flash ROM 2 Mbytes (Expand to 8MB)

LAN port 1 x Auto-MDIX RJ 45 for 10/100Mbps Ethernet

Network Standard IEEE 802.11b (Wi-Fi™) and IEEE 802.11g compliance

OFDM; 802.11bCCK (11 Mbps, 5.5 Mbps), DQPSK (2 Mbps), DBPSK (1 Mbps)

Operating Frequencies 2.412.2.497 GHz

Operating Channels 802.11g13 for North America, 13 for Europe (ETSI), 14 for Japan
802.11b11 for North America, 14 for Japan, 13 for Europe (ETSI)

Operating temperature 0~55℃

Storage temperature -20℃~70℃

Power Adapter DC 24V/500mA

Dimensions 141mm (W) x 100mm (D) x 27mm (H)

Wireless Specifications

Receive Sensitivity at 11Mbps min. -85dBm

Receive Sensitivity at 5.5Mbps min. -89dBm

Receive Sensitivity at 2Mbps min. -90dBm

Receive Sensitivity at 1Mbps min. -93dBm

Maximum Receive Level min. -5dBm

Transmit Power 18 dBm

Modulation Direct Sequence Spread Spectrum BPSK / QPSK / CCK

Throughput Up to 19 Mbps

Radio-on-Chip AR2112 · Wireless Interface · Embedded Atheros solution

Page 70 of the LevelOne WAP-0005 user manual — Software Specifications
Page 70 · click to enlarge
Page 70

Appendix A - Specifications

  • 30 Meters (100ft.) @ 11Mbps
  • 50 Meters (165ft.) @ 5.5Mbps
  • 70 Meters (230ft.) @ 2Mbps
  • 9 1Meters (300ft.) @ 1Mbps
  • 152 Meters (500ft.) @ 11Mbps
  • 270 Meters (885ft.) @ 5.5Mbps
  • 396 Meters (1300ft.) @ 2 Mbps
  • 457 Meters (1500ft.) @ 1 Mbps

Software Specifications

Wireless • Access point support

  • Roaming supported
  • IEEE 802.11g/11b compliance
  • Supper G (up to 108Mbps)
  • Auto Sensing Open System / Share Key authentication
  • Wireless Channels Support
  • Automatic Wireless Channel Selection
  • Antenna selection
  • Tx Power Adjustment
  • Country Selection
  • Preamble Type: long or short support
  • RTS Threshold Adjustment
  • Fragmentation Threshold Adjustment
  • Beacon Interval Adjustment
  • SSID assignment

Operation Mode • Common AP

  • Repeater
  • Client AP

Security • Open, shared, WPA, and WPA-PSK authentication

  • 802.1x support
  • EAP-TLS, EAP-TTLS, PEAP
  • Block inter-wireless station communication
  • Block SSID broadcast

Management • Web based configuration

  • RADIUS Accounting
  • RADIUS-On feature
  • RADIUS Accounting update
  • CLI

Operating Range Indoors · Outdoors · Feature Details

Page 71 of the LevelOne WAP-0005 user manual — Appendix A Specifications
Page 71 · click to enlarge
Page 71
  • Message Log
  • Access Control list file support
  • Configuration file Backup/Restore
  • Statistics support
  • Device discovery program
  • Windows Utility

Other Features • DHCP client

  • WINS client

Firmware Upgrade HTTP, FTP network protocol download

Page 72 of the LevelOne WAP-0005 user manual — FCC Radiation Exposure Statement
Page 72 · click to enlarge
Page 72

Appendix A - Specifications

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica- tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Page 73 of the LevelOne WAP-0005 user manual — General Problems
Page 73 · click to enlarge
Page 73

B

Appendix B Troubleshooting

Overview

This chapter covers some common problems that may be encountered while using the Wireless Access Point and some possible solutions to them. If you follow the suggested steps and the Wireless Access Point still does not function properly, contact your dealer for further advice.

General Problems

Problem 1: Can't connect to the Wireless Access Point to configure it.

Solution 1Check the following:
  • The Wireless Access Point is properly installed, LAN connections are OK, and it is powered ON. Check the LEDs for port status.
  • Ensure that your PC and the Wireless Access Point are on the same network segment. (If you don't have a router, this must be the case.)
  • If your PC is set to "Obtain an IP Address automatically" (DHCP client), restart it.
  • You can use the following method to determine the IP address of the Wireless Access Point, and then try to connect using the IP address, instead of the name.

To Find the Access Point's IP Address 1. Open a MS-DOS Prompt or Command Prompt Window. 2. Use the Ping command to “ping” the Wireless Access Point. Enter ping followed by the Default Name of the Wireless Access Point. e.g.

ping SC003318 3. Check the output of the ping command to determine the IP address of the Wireless Access Point, as shown below.

LevelOne WAP-0005 — General Problems diagram (page 73)
Fig. 54 · General Problems

Figure 56: Ping If your PC uses a Fixed (Static) IP address, ensure that it is using an IP Address which is compatible with the Wireless Access Point. (If no DHCP Server is found, the Wireless Access Point will default to an IP Address and Mask of 192.168.0.228 and 255.255.255.0.) On Windows PCs, you can use Control Panel-Network to check the Properties for the TCP/IP protocol.

Problem 2: My PC can't connect to the LAN via the Wireless Access Point.

Page 74 of the LevelOne WAP-0005 user manual — Appendix B Troubleshooting
Page 74 · click to enlarge
Page 74

Appendix B - Troubleshooting

Solution 2 Check the following:

  • The SSID and WEP settings on the PC match the settings on the Wireless Access Point.
  • On the PC, the wireless mode is set to "Infrastructure"
  • If using the Access Control feature, the PC's name and address is in the Trusted Stations list.
  • If using 802.1x mode, ensure the PC's 802.1x software is configured correctly. See Chapter 4 for details of setup for the Windows XP 802.1x client. If using a different client, refer to the vendor's documentation.
Page 75 of the LevelOne WAP-0005 user manual — Checking TCP/IP Settings - Windows 9x/ME:
Page 75 · click to enlarge
Page 75

Appendix C Windows TCP/IP

Overview

Normally, no changes need to be made. • By default, the Wireless Access Point will act as a DHCP client, automatically obtaining a suitable IP Address (and related information) from your DHCP Server.

  • If using Fixed (specified) IP addresses on your LAN (instead of a DHCP Server), there is no need to change the TCP/IP of each PC. Just configure the Wireless Access Point to match your existing LAN.

The following sections provide details about checking the TCP/IP settings for various types of Windows, should that be necessary.

Checking TCP/IP Settings - Windows 9x/ME:

1. Select Control Panel - Network . You should see a screen like the following:
LevelOne WAP-0005 — Checking TCP/IP Settings - Windows 9x/ME: diagram (page 75)
Fig. 55 · Checking TCP/IP Settings - Windows 9x/ME:
Figure 57Network Configuration
2. Select the TCP/IP protocol for your network card. 3. Click on the Properties button. You should then see a screen like the following.
Page 76 of the LevelOne WAP-0005 user manual — Using "Specify an IP Address"
Page 76 · click to enlarge
Page 76

Appendix C – Windows TCP/IP

LevelOne WAP-0005 — Appendix C Windows TCP/IP diagram (page 76)
Fig. 56 · Appendix C Windows TCP/IP
Figure 58IP Address (Win 95)

Ensure your TCP/IP settings are correct, as follows:

Using DHCP

To use DHCP, select the radio button Obtain an IP Address automatically. This is the default Windows settings. To work correctly, you need a DHCP server on your LAN.

Using "Specify an IP Address"

If your PC is already configured for a fixed (specified) IP address, no changes are required.

(The Administrator should configure the Wireless Access Point with a fixed IP address from the same address range used on the PCs.)

Page 77 of the LevelOne WAP-0005 user manual — Checking TCP/IP Settings - Windows NT4.0
Page 77 · click to enlarge
Page 77

Checking TCP/IP Settings - Windows NT4.0

1. Select Control Panel - Network , and, on the Protocols tab, select the TCP/IP protocol, as shown below.
LevelOne WAP-0005 — Checking TCP/IP Settings - Windows NT4.0 diagram (page 77)
Fig. 57 · Checking TCP/IP Settings - Windows NT4.0
Figure 59Windows NT4.0 - TCP/IP
2. Click the Properties button to see a screen like the one below.
LevelOne WAP-0005 — Checking TCP/IP Settings - Windows NT4.0 diagram (page 77)
Fig. 58 · Checking TCP/IP Settings - Windows NT4.0
Figure 60Windows NT4.0 - IP Address
Page 78 of the LevelOne WAP-0005 user manual — Using "Specify an IP Address"
Page 78 · click to enlarge
Page 78

Appendix C – Windows TCP/IP

3. Select the network card for your LAN. 4. Select the appropriate radio button - Obtain an IP address from a DHCP Server or Specify an IP Address , as explained below.

Obtain an IP address from a DHCP Server

This is the default Windows setting. This is the default Windows settings. To work correctly, you need a DHCP server on your LAN.

Using "Specify an IP Address"

If your PC is already configured for a fixed (specified) IP address, no changes are required.

(The Administrator should configure the Wireless Access Point with a fixed IP address from the same address range used on the PCs.)

Page 79 of the LevelOne WAP-0005 user manual — Checking TCP/IP Settings - Windows 2000
Page 79 · click to enlarge
Page 79

Checking TCP/IP Settings - Windows 2000

1. Select Control Panel - Network and Dial-up Connection . 2. Right click the Local Area Connection icon and select Properties . You should see a screen like the following:
LevelOne WAP-0005 — Checking TCP/IP Settings - Windows 2000 diagram (page 79)
Fig. 59 · Checking TCP/IP Settings - Windows 2000
Figure 61Network Configuration (Win 2000)
3. Select the TCP/IP protocol for your network card. 4. Click on the Properties button. You should then see a screen like the following.
LevelOne WAP-0005 — Checking TCP/IP Settings - Windows 2000 diagram (page 79)
Fig. 60 · Checking TCP/IP Settings - Windows 2000
Figure 62TCP/IP Properties (Win 2000)
Page 80 of the LevelOne WAP-0005 user manual — Using a fixed IP Address ("Use the following IP Address")
Page 80 · click to enlarge
Page 80

Appendix C – Windows TCP/IP

5. Ensure your TCP/IP settings are correct:

Using DHCP

To use DHCP, select the radio button Obtain an IP Address automatically. This is the default Windows setting. This is the default Windows settings. To work correctly, you need a DHCP server on your LAN.

Using a fixed IP Address ("Use the following IP Address")

If your PC is already configured for a fixed (specified) IP address, no changes are required.

(The Administrator should configure the Wireless Access Point with a fixed IP address from the same address range used on the PCs.)

Page 81 of the LevelOne WAP-0005 user manual — Checking TCP/IP Settings - Windows XP
Page 81 · click to enlarge
Page 81

Checking TCP/IP Settings - Windows XP

1. Select Control Panel - Network Connection . 2. Right click the Local Area Connection and choose Properties . You should see a screen like the following:
LevelOne WAP-0005 — Checking TCP/IP Settings - Windows XP diagram (page 81)
Fig. 61 · Checking TCP/IP Settings - Windows XP
Figure 63Network Configuration (Windows XP)
3. Select the TCP/IP protocol for your network card. 4. Click on the Properties button. You should then see a screen like the following.
LevelOne WAP-0005 — Checking TCP/IP Settings - Windows XP diagram (page 81)
Fig. 62 · Checking TCP/IP Settings - Windows XP
Figure 64TCP/IP Properties (Windows XP)
Page 82 of the LevelOne WAP-0005 user manual — Using a fixed IP Address ("Use the following IP Address")
Page 82 · click to enlarge
Page 82

Appendix C – Windows TCP/IP

5. Ensure your TCP/IP settings are correct.

Using DHCP

To use DHCP, select the radio button Obtain an IP Address automatically. This is the default Windows setting. To work correctly, you need a DHCP server on your LAN.

Using a fixed IP Address ("Use the following IP Address")

If your PC is already configured for a fixed (specified) IP address, no changes are required.

(The Administrator should configure the Wireless Access Point with a fixed IP address from the same address range used on the PCs.)

Page 83 of the LevelOne WAP-0005 user manual — ESS/ESSID
Page 83 · click to enlarge
Page 83

D

Appendix D About Wireless LANs

Overview

Wireless networks have their own terms and jargon. It is necessary to understand many of these terms in order to configure and operate a Wireless LAN.

Wireless LAN Terminology

Modes

Wireless LANs can work in either of two (2) modes:

  • Ad-hoc
  • Infrastructure

Ad-hoc Mode

Ad-hoc mode does not require an Access Point or a wired (Ethernet) LAN. Wireless Sta- tions (e.g. notebook PCs with wireless cards) communicate directly with each other.

Infrastructure Mode

In Infrastructure Mode, one or more Access Points are used to connect Wireless Stations (e.g. Notebook PCs with wireless cards) to a wired (Ethernet) LAN. The Wireless Stations can then access all LAN resources.

Access Points can only function in "Infrastructure" mode, and can communicate only with Wireless Stations which are set to "Infrastructure" mode.

SSID/ESSID

BSS/SSID

A group of Wireless Stations and a single Access Point, all using the same ID (SSID), form a Basic Service Set (BSS).

Using the same SSID is essential. Devices with different SSIDs are unable to communi- cate with each other. However, some Access Points allow connections from Wireless Stations which have their SSID set to “any” or whose SSID is blank ( null ).

ESS/ESSID

A group of Wireless Stations, and multiple Access Points, all using the same ID (ESSID), form an Extended Service Set (ESS).

Different Access Points within an ESS can use different Channels. To reduce interference, it is recommended that adjacent Access Points SHOULD use different channels.

Page 84 of the LevelOne WAP-0005 user manual — WPA-802.1x
Page 84 · click to enlarge
Page 84

Appendix D – About Wireless LANs

As Wireless Stations are physically moved through the area covered by an ESS, they will automatically change to the Access Point which has the least interference or best perform- ance. This capability is called Roaming. (Access Points do not have or require Roaming capabilities.)

Channels

The Wireless Channel sets the radio frequency used for communication.

  • Access Points use a fixed Channel. You can select the Channel used. This allows you to choose a Channel which provides the least interference and best performance. For 802.11g, 13 channels are available in the USA and Canada., but 11channels are available in North America if using 802.11b.
  • If using multiple Access Points, it is better if adjacent Access Points use different Channels to reduce interference. The recommended Channel spacing between adjacent Access Points is 5 Channels (e.g. use Channels 1 and 6, or 6 and 11).
  • In "Infrastructure" mode, Wireless Stations normally scan all Channels, looking for an Access Point. If more than one Access Point can be used, the one with the strongest signal is used. (This can only happen within an ESS.)
  • If using "Ad-hoc" mode (no Access Point), all Wireless stations should be set to use the same Channel. However, most Wireless stations will still scan all Channels to see if there is an existing "Ad-hoc" group they can join.

WEP

WEP (Wired Equivalent Privacy) is a standard for encrypting data before it is transmitted. This is desirable because it is impossible to prevent snoopers from receiving any data which is transmitted by your Wireless Stations. But if the data is encrypted, then it is meaningless unless the receiver can decrypt it.

If WEP is used, the Wireless Stations and the Wireless Access Point must have the same settings.

WPA-PSK

Like WEP, data is encrypted before transmission. WPA is more secure than WEP, and should be used if possible. The PSK (Pre-shared Key) must be entered on each Wireless station. The 256Bit encryption key is derived from the PSK, and changes frequently.

WPA-802.1x

WPA-802.1x - This version of WPA requires a Radius Server on your LAN to provide the client authentication according to the 802.1x standard. Data transmissions are encrypted using the WPA standard.

If this option is used:

  • The Access Point must have a "client login" on the Radius Server.
  • Each user must have a "user login" on the Radius Server.
  • Each user's wireless client must support 802.1x and provide the login data when required.
  • All data transmission is encrypted using the WPA standard. Keys are automatically generated, so no key input is required.
Page 85 of the LevelOne WAP-0005 user manual — Appendix D About Wireless LANs
Page 85 · click to enlarge
Page 85

This uses the 802.1x standard for client authentication, and WEP for data encryption. If possi- ble, you should use WPA-802.1x instead, because WPA encryption is much stronger than WEP encryption.

If this option is used:

  • The Access Point must have a "client login" on the Radius Server.
  • Each user must have a "user login" on the Radius Server.
  • Each user's wireless client must support 802.1x and provide the login data when required.
  • All data transmission is encrypted using the WEP standard. You only have to select the WEP key size; the WEP key is automatically generated.
Page 86 of the LevelOne WAP-0005 user manual — Using the CLI – Serial Port
Page 86 · click to enlarge
Page 86

E

Appendix E Command Line Interface

Overview

If desired, the command line interface (CLI) can be used for configuration. This provides the possibility of creating scripts to perform common configuration changes. The CLI requires a physical connection from your PC to the serial port (RS232 port) on the Wireless Access Point.

Using the CLI – Telnet

1. Start your Telnet client, and establish a connection to the Access Point. e.g.

Telnet 192.168.0.228

2. You will be prompted for the user name and password. Enter the same login name and password as used for the HTTP (Web) interface. The default values are admin for the User Name, and password for the Password. 3. Once connected, you can use any of the commands listed in the following Command Reference .

Using the CLI – Serial Port

1. Use a standard serial port cable to connect your PC to the serial (RS232) port on the Wireless Access point. 2. Start your communications program. For example, in Windows, use HyperTerminal. (This program may not be installed. If so, you can install it using Start – Settings – Control Panel – Add or Remove Programs . The select Windows Setup or Add/Remove Windows Components , depending on your version of Windows.) 3. Configure the connection properties:
  • Name – use a suitable name, such as “AP”
  • Port (Connect Using) – Select the Serial Port that the cable is connected to. (Do not select your modem.)
  • Port Settings – Use 9600, N, 8, 1, with hardware flow control, as shown below.
Page 87 of the LevelOne WAP-0005 user manual — Command Reference
Page 87 · click to enlarge
Page 87
LevelOne WAP-0005 — Command Reference diagram (page 87)
Fig. 63 · Command Reference
Figure 65CLI Port Settings
4. Use the “Connect” command to start the connection. 5. You will be prompted for a user name and password. Enter the current user name and password for the AP you are connecting to. 6. You will then see the prompt, and can then use any of the commands listed in the following Command Reference .

Command Reference

The following commands are available.

? -- Display CLI Command List

admin-- Temporary factory admin

boot flash -- Boot from flash

boot ethernet -- Boot from network

cp -- Copy file

config wlan-- config wlanX

connect bss-- connect to bssX

del acl -- Delete Access Control List

del key -- Delete Encryption key

find bss -- Find BSS

find channel -- Find Available Channel

find all -- Find All BSS

format -- Format flash filesytem

bootrom -- Update boot rom image

Page 88 of the LevelOne WAP-0005 user manual — Command Reference
Page 88 · click to enlarge
Page 88

Appendix E – Command Line Interface

ftp -- Software update via FTP

get 11gonly-- Display 11g Only Allowed

get 11goptimize -- Display 11g Optimization Level

get 11goverlapbss-- Display Overlapping BSS Protection

get acl -- Display Access Control List

get aging -- Display Aging Interval

get antenna-- Display Antenna Diversity

get association -- Display Association Table

get authentication -- Display Authentication Type

get autochannelselect -- Display Auto Channel Select

get basic11b -- Display Basic 11b Rates

get basic11g -- Display Basic 11g Rates

get beaconinterval -- Display Beacon Interval

get burstSeqThreshold -- Display Max Number of frames in a Burst

get burstTime -- Display Burst Time

get calibration -- Display Noise And Offset Calibration Mode

get cckTrigHigh -- Display Higher Trigger Threshold for CCK Phy Errors for ANI Control

get cckTrigLow -- Display Lower Trigger Threshold for CCK Phy Errors for ANI Control

get cckWeakSigThr-- Display ANI Parameter for CCK Weak Signal Detection Threshold

get channel-- Display Radio Channel

get cipher -- Display Encryption cipher

get compproc -- Display Compression scheme

get compwinsize -- Display Compression Window Size

get config -- Display Current AP Configuration

get countrycode -- Display Country Code

get ctsmode-- Display CTS mode

get ctsrate-- Display CTS rate

get ctstype-- Display CTS type

get description -- Display Access Point Description

get dhcpmode -- Display dhcp mode

get domainsuffix -- Display Domain Name Server suffix

get dtim -- Display Data Beacon Rate (DTIM)

get enableANI -- Display Adaptive Noise Immunity Control On/Off

get encryption -- Display Encryption Mode

get extendedchanmode -- Display Extended Channel Mode

get firStepLvl -- Display ANI Parameter for FirStepLevel

get abolt --

Page 89 of the LevelOne WAP-0005 user manual — Command Reference
Page 89 · click to enlarge
Page 89

get fragmentthreshold -- Display Fragment Threshold

get frequency -- Display Radio Frequency (MHz)

get gateway-- Display Gateway IP Address

get gbeaconrate -- Display 11g Beacon Rate

get gdraft5-- Display 11g Draft 5.0 compatibility

get groupkeyupdate -- Display Group Key Update Interval (in Seconds)

get hardware -- Display Hardware Revisions

get hostipaddr -- Display Host IP Address

get ipaddr -- Display IP Address

get ipmask -- Display IP Subnet Mask

get key -- Display Encryption Key

get keyentrymethod -- Display Encyrption Key Entry Method

get keysource -- Display Source Of Encryption Keys

get login -- Display Login User Name

get minimumrate -- Display Minimum Rate

get macAuth-- Display Mac Authentication Enable/Disable

get nameaddr -- Display IP address of name server

get nf -- Display Noise Floor

get noiseImmunityLvl -- Display ANI Parameter for Noise Immunity Level

get ofdmTrigHigh -- Display Higher Trigger Threshold for OFDM Phy Errors for ANI Con- trol

get ofdmTrigLow -- Display Lower Trigger Threshold for OFDM Phy Errors for ANI Con- trol

get ofdmWeakSigDet -- Display ANI Parameter for OFDM Weak Signal Detection

get overRidetxpower -- Display Tx power override

get operationMode-- Display Operation Mode

get pktLogEnable -- Display Packet Logging Mode

get power -- Display Transmit Power Setting

get quietAckCtsAllow -- Display if Ack/Cts frames are allowed during quiet period

get quietDuration-- Display Duration of quiet period

get quietOffset -- Display Offset of quiet period into the beacon period

get radiusname -- Display RADIUS server name or IP address

get radiusport -- Display RADIUS port number

get rate -- Display Data Rate

get remoteAp -- Display Remote Ap's Mac Address

get hwtxretries -- Display HW Transmit Retry Limit

get swtxretries -- Display SW Transmit Retry Limit

Page 90 of the LevelOne WAP-0005 user manual — Command Reference
Page 90 · click to enlarge
Page 90

Appendix E – Command Line Interface

get rtsthreshold -- Display RTS/CTS Threshold

get shortpreamble-- Display Short Preamble Usage

get shortslottime-- Display Short Slot Time Usage

get sntpserver -- Display SNTP/NTP Server IP Address

get softwareretry-- Display Software Retry

get spurImmunityLvl -- Display ANI Parameter for Spur Immunity Level

get ssid -- Display Service Set ID

get ssidsuppress -- Display SSID Suppress Mode

get snmpMode -- Display SNMP Mode

get snmpCommunity-- Display SNMP Community Name

get snmpAccessRight -- Display SNMP Access Right

get snmpAnyStaMode -- Display SNMP Any Station Mode

get snmpStationIPAddr -- Display SNMP Station Addr

get trapMode -- Display Trap Mode

get trapVersion -- Display Trap Version

get trapSendMode -- Display Trap Send Mode

get trapRecvIp -- Display Trap Receiver IP

get station-- Display Station Status

get SuperG -- Display SuperG Feature Status

get systemname -- Display Access Point System Name

get telnet -- Display Telnet Mode

get timeout-- Display Telnet Timeout

get tzone -- Display Time Zone Setting

get updateparam -- Display Vendor Default Firmware Update Params

get uptime -- Display UpTime

get watchdog -- Display Watchdog Mode

get wds -- Display WDS Mode

get wep -- Display Encryption Mode

get wirelessmode -- Display Wireless LAN Mode

get winsEnable -- Display WINS Server Enable/Disable

get winsserveraddr -- Display IP address of WINS server

get wSeparate -- Display wireless seprate Mode

get wlanstate -- Display wlan state

help -- Display CLI Command List

Lebradeb -- Disable reboot during radar detection

ls -- list directory

mem -- system memory statistics

Page 91 of the LevelOne WAP-0005 user manual — Command Reference
Page 91 · click to enlarge
Page 91

mv -- Move file

np -- Network Performance

ns -- Network Performance Server

pktLog -- Packet Log

radar! -- Simulate radar detection on current channel

reboot -- Reboot Access Point

rm -- Remove file

run -- Run command file

set 11gonly-- Set 11g Only Allowed

set 11goptimize -- Set 11g Optimization Level

set 11goverlapbss-- Set Overlapping BSS Protection

set acl -- Set Access Control List

set aging -- Set Aging Interval

set antenna-- Set Antenna

set authentication -- Set Authentication Type

set autochannelselect -- Set Auto Channel Selection

set basic11b -- Set Use of Basic 11b Rates

set basic11g -- Set Use of Basic 11g Rates

set beaconinterval -- Modify Beacon Interval

set burstSeqThreshold -- Set Max Number of frames in a Burst

set burstTime -- Set Burst Time

set calibration -- Set Calibration Period

set cckTrigHigh -- Set Higher Trigger Threshold for CCK Phy Errors For ANI Control

set cckTrigLow -- Set Lower Trigger Threshold for CCK Phy Errors For ANI Control

set cckWeakSigThr-- Set ANI Parameter for CCK Weak Signal Detection Threshold

set channel-- Set Radio Channel

set cipher -- Set Cipher

set compproc -- Set Compression Scheme

set compwinsize -- Set Compression Window Size

set countrycode -- Set Country Code

set ctsmode-- Set CTS Mode

set ctsrate-- Set CTS Rate

set ctstype-- Set CTS Type

set description -- Set Access Point Description

ping -- Ping · quit -- Logoff · set abolt --

Page 92 of the LevelOne WAP-0005 user manual — Command Reference
Page 92 · click to enlarge
Page 92

Appendix E – Command Line Interface

set dhcpMode -- Set Dhcp Mode

set domainsuffix -- Set Domain Name Server Suffix

set dtim -- Set Data Beacon Rate (DTIM)

set enableANI -- Turn Adaptive Noise Immunity Control On/Off

set encryption -- Set Encryption Mode

set extendedchanmode -- Set Extended Channel Mode

set factorydefault -- Restore to Default Factory Settings

set firStepLvl -- Set ANI Parameter for FirStepLevel

set fragmentthreshold -- Set Fragment Threshold

set frequency -- Set Radio Frequency (MHz)

set gateway-- Set Gateway IP Address

set gbeaconrate -- Set 11g Beacon Rate

set groupkeyupdate -- Set Group Key Update Interval (in Seconds)

set gdraft5-- Set 11g Draft 5.0 compatibility

set hostipaddr -- Set Host IP address

set ipaddr -- Set IP Address

set ipmask -- Set IP Subnet Mask

set key -- Set Encryption Key

set keyentrymethod -- Select Encryption Key Entry Method

set keysource -- Select Source Of Encryption Keys

set login -- Modify Login User Name

set minimumrate -- Set Minimum Rate

set macAuth-- Set Mac Authentication Enable/Disable

set nameaddress -- Set Name Server IP address

set noiseImmunityLvl -- Set ANI Parameter for Noise Immunity Level

set ofdmTrigHigh -- Set Higher Trigger Threshold for OFDM Phy Errors for ANI Control

set ofdmTrigLow -- Set Lower Trigger Threshold for OFDM Phy Errors for ANI Control

set ofdmWeakSigDet -- Set ANI Parameter for OFDM Weak Signal Detection

set overRidetxpower -- Set Tx power override

set operationMode-- Set operation Mode

set password -- Modify Password

set passphrase -- Modify Passphrase

set pktLogEnable -- Enable Packet Logging

set power -- Set Transmit Power

set quietAckCtsAllow -- Allow Ack/Cts frames during quiet period

set quietDuration-- Duration of quiet period

set quietOffset -- Offset of quiet period into the beacon period

Page 93 of the LevelOne WAP-0005 user manual — Command Reference
Page 93 · click to enlarge
Page 93

set radiusname -- Set RADIUS name or IP address

set radiusport -- Set RADIUS port number

set radiussecret -- Set RADIUS shared secret

set rate -- Set Data Rate

set rate -- Set Data Rate

set rate -- Set Data Rate

set rate -- Set Data Rate

set rate -- Set Data Rate

set regulatorydomain -- Set Regulatory Domain

set remoteAP -- Set Remote AP's Mac Address

set hwtxretries -- Set HW Transmit Retry Limit

set swtxretries -- Set SW Transmit Retry Limit

set rtsthreshold -- Set RTS/CTS Threshold

set shortpreamble-- Set Short Preamble

set shortslottime-- Set Short Slot Time

set sntpserver -- Set SNTP/NTP Server IP Address

set softwareretry-- Set Software Retry

set spurImmunityLvl -- Set ANI Parameter for Spur Immunity Level

set ssid -- Set Service Set ID

set ssidsuppress -- Set SSID Suppress Mode

set SuperG -- Super G Features

set systemname -- Set Access Point System Name

set snmpMode -- Set SNMP Mode

set snmpCommunity-- Set SNMP Community Name

set snmpAccessRight -- Set SNMP Access Right

set snmpAnyStaMode -- Set SNMP Any Station Mode

set snmpStationIPAddr -- Set SNMP Station Addr

set trapMode -- Set Trap Mode

set trapVersion -- Set Trap Version

set trapSendMode -- Set Trap Send Mode

set trapRecvIp -- Set Trap Receiver IP

set telnet -- Set Telnet Mode

set timeout-- Set Telnet Timeout

set tzone -- Set Time Zone Setting

set updateparam -- Set Vendor Default Firmware Update Params

set watchdog -- Set Watchdog Mode

set wds -- Set WDS Mode

Page 94 of the LevelOne WAP-0005 user manual — Command Reference
Page 94 · click to enlarge
Page 94

Appendix E – Command Line Interface

set wep -- Set Encryption Mode

set wlanstate -- Set wlan state

set wirelessmode -- Set Wireless LAN Mode

set winsEnable -- Set WINS Server Enable/Disable

set winsServerAddr -- Set WINS Server IP address

set wSeparate -- Set wireless seprate Mode

spy report -- Print spy report

spy start -- Start spy

spy stop -- Stop spy

start wlan -- Start the current wlan

stop wlan -- Stop the current wlan

timeofday -- Display Current Time of Day

version -- Software version

Ask about the LevelOne WAP-0005

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LevelOne WAP-0005

Be the first to ask — other owners or our team will answer.

Original document

LevelOne WAP-0005 manual PDF

94 pages·3.2 MB·Webcam·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…