EN
LevelOne logo
Official user manual

LevelOne PLI-2000

8 pages·640 KB·Network Card·PDF·ENDEFRITNLJA
LevelOne PLI-2000
Table of Contents 17 sections PLI-1000 · PLI-2000 · LevelOne Homeplug Utility · USER MANUAL · … ShowHide
Page 1 of the LevelOne PLI-2000 user manual — PLI-1000
Page 1 · click to enlarge
Page 1
LevelOne PLI-2000 — PLI-1000 diagram (page 1)
Fig. 1

PLI-1000

PLI-2000

LevelOne Homeplug Utility

USER MANUAL

Page 2 of the LevelOne PLI-2000 user manual — Running the utility
Page 2 · click to enlarge
Page 2

Introduction

The Homeplug Configuration Utility for PLI-1000 and PLI-2000(USB & Ethernet) enables the user to find Homeplug devices on the powerline network, measure data rate performance and ensure privacy by setting a user defined network private password. This utility gives you the capability to set up a network password on the local device connected to the computer where the utility is running. It gives you as well, through the advanced option, the capability to set up a network password remotely on other Homeplug devices through the power line.

It is recommended that the same PC chosen for initial execution of this utility remain the PC of choice for subsequent network encryption updates. Network setup information is stored on the PC and is used to facilitate follow-on network encryption sessions.

Before running this utility, make sure that a Homeplug device is properly installed and connected to your computer.

Running the utility

To run the utility, double click the Homeplug Configuration Utility icon on your desktop.

LevelOne PLI-2000 — Running the utility diagram (page 2)
Fig. 2 · Running the utility

The wizard has five different dialog screens options accessible through the following tabs : Device, Network, Security, Advanced and About. In the coming sections, we will explain the purpose and the functionality of each of them.

NBAs a general rule that applies to dialog screens, pressing:

The OK and Cancel buttons means “ exit utility ”

Page 3 of the LevelOne PLI-2000 user manual — Figure 1 Initial screen when wizard is started
Page 3 · click to enlarge
Page 3

Device dialog screen

The Device dialog screen provides a list of your Homeplug devices connected to the computer where the utility is running and average data rate performance of your powerline network.

Initially, the wizard starts the Device dialog screen.

LevelOne PLI-2000 — Device dialog screen diagram (page 3)
Fig. 3 · Device dialog screen

Figure 1 Initial screen when wizard is started

Page 4 of the LevelOne PLI-2000 user manual — Figure 2 Device Dialog screen
Page 4 · click to enlarge
Page 4

Once the analysis is done, a screen similar to Figure 2 appears.

In the text list box, it reports back all Homeplug devices found that are locally connected to the computer where the utility is running.

In most cases, one device only is listed.

In case you have more, click on one of them and hit Connect. Make sure that the State box indicates that your PC is connected to the same device. Now you are ready to manage the powerline network connected to this device, ensure its privacy and measure its data rate performance.

Press Refresh button to refresh the search of the powerline devices connected to your computer.

The progress bar will change into a status bar indicating the network average data rate.

The color of the bar reflects the average performance of the powerline network :

GreenExcellent performance
YellowFair performance
RedPoor performance
LevelOne PLI-2000 — Figure 2 Device Dialog screen diagram (page 4)
Fig. 4 · Figure 2 Device Dialog screen

Figure 2 Device Dialog screen

Page 5 of the LevelOne PLI-2000 user manual — Figure 3 Network dialog screen
Page 5 · click to enlarge
Page 5

Network dialog screen

The Network dialog screen provides detailed information about your powerline network.

The text list box shows all Homeplug devices found on your powerline network identified by their MAC addresses. A second column indicates their data rate measurements in Mbps.

Press Scan Powerline Network button to refresh the listed information.

LevelOne PLI-2000 — Network dialog screen diagram (page 5)
Fig. 5 · Network dialog screen

Figure 3 Network dialog screen

In case a Homeplug device in your home is not listed in the screen above, make sure that its network password has not been made private previously with a different password than your current private network password.

You can always reset a Homeplug network password to the universal one by running the Homeplug Configuration Utility on the PC attached to this device and choose “HomePlug” as the network password.

Page 6 of the LevelOne PLI-2000 user manual — Figure 4 Security Dialog screen
Page 6 · click to enlarge
Page 6

Security dialog screen

All Homeplug devices are shipped using “HomePlug” as a network password. The Security dialog screen allows you to change this network password and set your own private password and apply it to the Homeplug device connected to the computer where the utility is running.

Hit Restore Default button to restore the original network password “HomePlug” and apply it locally.

Hit Set Local button to change the network password locally.

LevelOne PLI-2000 — Security dialog screen diagram (page 6)
Fig. 6 · Security dialog screen

Figure 4 Security Dialog screen

Page 7 of the LevelOne PLI-2000 user manual — Figure 5 Advanced dialog screen
Page 7 · click to enlarge
Page 7

Advanced dialog screen

The Advanced dialog screen allows you to set up a network password remotely on other Homeplug devices through the powerline.

Type your private network password into the Network Password text box.

The other devices on the network with Homeplug capabilities will have a different password printed on either the box itself or in the documentation. Find the passwords for all devices you want to manage and type them one by one into the Device Password text box and hit Add. This will add the passwords to Remote Passwords text list box and set them to the currently defined Network Password.

The Status indicates whether each device is successfully set to the Network Password. “OK” indicates success while “Fail” indicates a failure.

Hit Set All to apply your private network password to all devices that are listed in the Remote Passwords text list box and to your local device connected to the computer where the utility is running as well.

Select a password and Hit Remove to remove it from the list.

LevelOne PLI-2000 — Advanced dialog screen diagram (page 7)
Fig. 7 · Advanced dialog screen

Figure 5 Advanced dialog screen

Page 8 of the LevelOne PLI-2000 user manual — Figure 6 About dialog screen
Page 8 · click to enlarge
Page 8

About dialog screen

The About dialog screen shows the software version and provides a hot key to access the Intellon website

LevelOne PLI-2000 — About dialog screen diagram (page 8)
Fig. 8 · About dialog screen

Figure 6 About dialog screen

Ask about the LevelOne PLI-2000

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LevelOne PLI-2000

Be the first to ask — other owners or our team will answer.

Original document

LevelOne PLI-2000 manual PDF

8 pages·640 KB·Network Card·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…