EN
LevelOne logo
Official user manual

LevelOne FSW-0809

16 pages·102 KB·Computer Hardware·PDF·ENDEFRITNLJA
LevelOne FSW-0809
Table of Contents 14 sections Introduction · Features · Package Content · Hardware Description · … ShowHide
Page 1 of the LevelOne FSW-0809 user manual — 4+4 PoE Fast Ethernet Switch
Page 1 · click to enlarge
Page 1

LevelOne

FSW-0809

4+4 PoE Fast Ethernet Switch

User Manual

v1.0 - 0706

Page 2 of the LevelOne FSW-0809 user manual
Page 2 · click to enlarge
Page 2

Safety FCC Warning This equipment has been tested and found to comply with the regulations for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his or her own expense. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Page 4 of the LevelOne FSW-0809 user manual
Page 4 · click to enlarge
Page 4
Page 4 of the LevelOne FSW-0809 user manual
Page 5 of the LevelOne FSW-0809 user manual — Introduction
Page 5 · click to enlarge
Page 5

Introduction

The FSW-0809 Switch integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible package. And this switch’s Port-1 to Port-4 are Power over Ethernet (PoE) ports, and it will automatically detects the presence of IEEE 802.3af-compliant powered device (PD) and provides power through the Port-1 to Port-4. The switch provides up to 15.4 W for PoE port and can be used to WLAN access point, IP phone, video camera and other PD devices. The Switch will automatically detect the network appliance’s requirements, and the switch will supplies the required power current to each appliance. Purpose Power over Ethernet (PoE) integrates power and data onto one single cabling infrastructure, eliminating the need to have AC power available at all locations. PoE is already widely adopted in the market, saving up to 50% of overall installation costs by eliminating the need to install separate electrical wiring and power outlets.

Page 6 of the LevelOne FSW-0809 user manual — Features
Page 6 · click to enlarge
Page 6

Features

ƒ 8 ×10/100Mbps Auto-negotiation Fast Ethernet RJ45 ports with 4-port PoE function (port-1 ~ port-4) ƒ Compliant with 802.3af specification ƒ Supports PoE power up to 15.4W for PoE port ƒ Supports PoE power up to 30W for all PoE ports ƒ Supports PoE Powered Device (PD) classification identify ƒ Each port supports auto MDI/MDIX, so there is no need to use cross-over cables or an up-link port ƒ Full/half duplex transfer mode for each port ƒ Wire speed reception and transmission ƒ Up to 1K unicast addresses entities per device, self-learning, and table aging ƒ 96KBytes packet buffer ƒ Supports IEEE 802.3x flow control for full- duplex mode ports ƒ Supports Back-pressure flow control for half-duplex mode ports

Page 7 of the LevelOne FSW-0809 user manual — Package Content
Page 7 · click to enlarge
Page 7

Package Content

Open the shipping cartons of the Switch and carefully unpacks its contents. The carton should contain the following items: – FSW-0809 – AC power adapter (Output: DC48V, 0.8A) – Four rubber feet – User Manual If any item is found missing or damaged, please contact your local reseller for replacement.

Page 8 of the LevelOne FSW-0809 user manual — Rear Panel
Page 8 · click to enlarge
Page 8

Hardware Description

This chapter describes the front panel, rear panel, and LED indicators of the Switch.

Front Panel

LevelOne FSW-0809 — Front Panel diagram (page 8)
Fig. 1 · Front Panel

LED Indicator: Comprehensive LED indicators display the status of the switch and the network (see the LED Indicators chapter below).

Rear Panel

PoE Ports (Port 1~4): These ports are PoE Enabled ports, the PoE port will automatically activated when a compatible terminal is identified, the Switch will supply power through the Ethernet port to the connected PoE device. Note: The PoE ports will not offer the power to the Legacy devices.

Page 9 of the LevelOne FSW-0809 user manual — Hardware Description
Page 9 · click to enlarge
Page 9

Ethernet Ports (Port 5~8): These ports support network speeds of either 10Mbps or 100Mbps, and can operate in half- and full- duplex transfer modes. These ports also supports automatic MDI/MDIX crossover detection function gives true “plug and play” capability, just need to plug-in the network cable to the hub directly and don’t care if the end node is NIC (Network Interface Card) or switch and hub DC Power Jack: Power is supplied through an external DC power adapter. Check the technical specification section for information about the DC power input voltage. Since the switch does not include a power switch, plugging its power adapter into a power outlet will immediately power it on.

Page 10 of the LevelOne FSW-0809 user manual — LED Indicators
Page 10 · click to enlarge
Page 10

LED Indicators The front panel LEDs provides instant status feedback, and, helps monitor and troubleshoot when needed.

On :When the Power LED lights on, the Switch is receiving power. Off :When the Power turns off or the power cord has improper connection.
Green :When the PoE powered device (PD) was connected and the port supplies power successfully. Yellow :When the PoE port have the following failure happens: ƒ PoE power circuit shortage ƒ Power over current: over the power current of PD’s classification ƒ Out of PoE voltage of 44 ~ 57 VDC output Off :No PoE powered device (PD) connected.

System Power

Page 11 of the LevelOne FSW-0809 user manual — PoE MAX
Page 11 · click to enlarge
Page 11
On :When the system was connected to PoE PD and the power resource remain <=7.5W, the LED lights on, the system will not provide power to the additional PoE PD inserted. Off :When the system have enough power of >7.5W.
Link/ : ACTThese LED indicators are lighted up when there is a secure connection (or Link) to the desired port. The LED indicators blinking whenever there is reception or transmission (i.e. Activity - Act) of data occurring at a port. 100M :When the 100M LED lights on, the respective port is successfully connected to 100M Fast Ethernet network. Otherwise, when the 100M LED is blinking, the port is transmitting or receiving data on the Fast Ethernet network. Off :No link.

PoE MAX

Page 12 of the LevelOne FSW-0809 user manual — PoE Rule
Page 12 · click to enlarge
Page 12

PoE Rule

PoE Max: this function will help to protect the PoE Switch and to stabilize the power transmitting to the powered device (PD). If the system power remain

Page 13 of the LevelOne FSW-0809 user manual — PoE Rule
Page 13 · click to enlarge
Page 13

Priority: this function will help to protect the system when the system power was over loaded, the system will disable PoE function of the lower priority PoE port to maintain the power budget to the PoE port which is in high priority. The total power resource of the system is 30 watt sharing to the 4 PoE ports (maximum power for per port is 15.4 watt), when the PoE PD shared the power resource for over 30 watt, the system will automatically arrange the priority of these ports, the low port number will have the higher priority than the high port number, Port 1 > Port 2 > Port 3 > Port 4. For example: In this PoE Switch, Port 2 is using power with 7 watt, Port 3 is using power with 15.4 watt, these two ports are totally using 22.4 watt power, when there is an additional PoE PD inserted to Port 1 with 15.4 watt, that means the system power resource was over current, then the priority function will activate, the priority will set to the lowest port number then to highest port number, so Port 1 will have the 15.4 watt power, Port 2 will have 7 watt power, and the system will cut off the power transmitting to the Port 3 due to over current.

Page 14 of the LevelOne FSW-0809 user manual — Installation
Page 14 · click to enlarge
Page 14

Installation

The setup of the Switch can be performed using the following steps: 1. The surface must support at least 1.5 Kg for the Switch. 2. The power outlet should be within 1.82 meters (6 feet) of the Switch. 3. Visually inspect the DC power jack and make sure that it is fully secured to the power adapter. 4. Make sure that there is proper heat dissipation from and adequate ventilation around the Switch. Do not place heavy objects on the Switch. Connecting Network Cable The Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and it runs both in half and full duplex mode using two pair of Category 5 cable. These RJ45 ports are Auto-MDI type port. The Switch can auto transform to MDI-II or MDI-X type, so you can just make an easy connection that without worrying if you are using a standard or crossover RJ45 cable.

Page 15 of the LevelOne FSW-0809 user manual — Technical Specifications
Page 15 · click to enlarge
Page 15

Technical Specifications

IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3x Full Duplex Flow Control IEEE 802.3af Power over Ethernet

Ethernet10Mbps (half duplex) 20Mbps (full-duplex) Fast Ethernet: 100Mbps (half duplex) 200Mbps (full-duplex)
10BASET2-pair UTP Cat. 3, 4, 5 100BASE-TX: 2-pair UTP Cat. 5 (up to 100m)

4 × 10/100Mbps Auto-MDIX RJ45 ports with PoE enabled (port 1 ~ port 4) 4 × 10/100Mbps Auto-MDIX RJ45 ports (port 5 ~ port 8)

PoE Power on RJ-45

Power+ping 3 & ping 6 Power-: ping 1 & ping 2

DC inputs 48VDC/0.8A

6.3 watts. (max. no PD device connected) 36.3 watts (max. with 30w PD connected)

Temperature Operating0 ° ~40 ° C, Storage: -10 ° ~70 ° C
Humidity Operating10% ~ 90%, Storage: 5% ~ 90%

Dimensions 171 x 98 x 29 mm

EMIFCC Class B, CE Mark Class B
Show 9 more labels / short text on this page
General · Standards · Protocol CSMA/CD · Data Transfer Rate · Topology Star · Network Cables · Number of Ports · Physical and Environmental · Power Consumption
Page 16 of the LevelOne FSW-0809 user manual — Technical Specifications
Page 16 · click to enlarge
Page 16
RAM Buffer96K bytes per device
Filtering Address Table1K entries per device

Packet Filtering / Forwarding Rate:

10Mbps Ethernet14,880/pps 100Mbps Fast Ethernet: 148,800/pps
MAC Address LearningAutomatic update
Transmits MethodStore-and-forward

Performance

Ask about the LevelOne FSW-0809

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LevelOne FSW-0809

Be the first to ask — other owners or our team will answer.

Original document

LevelOne FSW-0809 manual PDF

16 pages·102 KB·Computer Hardware·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…