EN
LevelOne logo
Official user manual

LevelOne Print Server (FPS-3003)

75 pages·4 MB·Server·PDF·ENDEFRITNLJA
LevelOne Print Server (FPS-3003)
Table of Contents 59 sections LevelOne · FPS-3003 · 2-port USB/MFP Server · User`s Manual · … ShowHide
LevelOnep.1FPS-3003p.12-port USB/MFP Serverp.1User`s Manualp.1CHAPTER5 ADDING PRINTERS IN UNIX/LINUX ...........................................33p.3CHAPTER6 FILE SERVER FUNCTION.......................................................37p.3CHAPTER7 SCAN SERVER FUNCTION .....................................................43p.3CHAPTER8 LEVELONE MFP CONTROL CENTER .................................47p.3Chapter1 Introductionp.5Chapter2 Product Overviewp.62.4 Installation Methodsp.8Chapter3 Basic Installationp.103.1 Connecting the Hardwarep.10Chapter4 Adding Printers in Windowsp.184.2.1 MFP Server and Windows PC on Same LANp.19PCp.194.2.2 MFP Server and Windows PC on Different LANsp.19# If your server is running on a different LAN than yourp.21Protocolp.23Printingp.264.4.5 Using Standard Windows Method for Raw TCP Printingp.284.4.7 Using Standard Windows Method for IPP Printingp.31Chapter5 Adding Printers in Unix/Linuxp.335.3 Using FPS-3003 on BSD UNIX/Linuxp.345.4 Using RedHat Linux Printer System Managerp.35Chapter6 File Server Functionp.376.4 Supported Code Pagesp.38„ FTPp.406.5.1 Use Shared Storages by SMB Method for Windowsp.406.5.2 Use Shared Storage by FTP Methods for Windowsp.41Chapter7 Scan Server Functionp.43HP MFPp.437.2 Using the Shared Scanner in Windowsp.437.2.1 Using LevelOne MFP Control Center Toolp.437.2.2 Using Windows Applicationsp.45Chapter8 LevelOne MFP Control Centerp.478.2.1 Use Tools of MFP Control Centerp.478.2.3 Set up Server’s Configurationp.48Š TCP/IPp.48Chapter 9 MFP Server’s Web Pagesp.55Chapter 10 Email Alertingp.62Chapter 11 SNMPp.62Chapter 12 Troubleshootingp.6312.1 LED Indicatorsp.63USB1p.63USB2p.63Chapter13 Restore Factory Defaultp.6513.1 Using Server’s Web Pagesp.6513.2 Using LevelOne MFP Control Centerp.6613.4 Default Parameters List Host Informationp.67Chapter14 Upgrade New Firmwarep.69Procedure A: Using PC User Softwarep.69Procedure B: Using Server’s Web Pagesp.69Procedure C: Using Init Button and TFTP Clientp.70Chapter15 Init Buttonp.71Chapter16 Technical Specificationsp.72- EN 60950p.73Chapter17 Appendixp.7417.1 Compatibility Listp.74
Page 1 of the LevelOne Print Server (FPS-3003) user manual — LevelOne
Page 1 · click to enlarge
Page 1
LevelOne Print Server (FPS-3003) — LevelOne diagram (page 1)
Fig. 1 · LevelOne

LevelOne

FPS-3003

2-port USB/MFP Server

User`s Manual

Page 2 of the LevelOne Print Server (FPS-3003) user manual — LevelOne
Page 2 · click to enlarge
Page 2
Page 2 of the LevelOne Print Server (FPS-3003) user manual — LevelOne
Page 3 of the LevelOne Print Server (FPS-3003) user manual — CHAPTER8 LEVELONE MFP CONTROL CENTER .................................47
Page 3 · click to enlarge
Page 3

4.2 Connecting FPS-3003 MFP Server 19 4.2.1 MFP Server and Windows PC on Same LAN 19 4.2.2 MFP Server and Windows PC on Different LANs 19 4.3 Setting up Local Windows Printer Driver 20 4.4 Adding Network Printers in Windows 20 4.4.1 Using Standard Windows Methods for SMB Printing Protocol ..21 4.4.2 Using LevelOne MFP Control Center Tool for SMB Printing 22 4.4.3 Using Standard Windows Methods for LPR Printing Protocol ...23 4.4.4 Using LevelOne MFP Control Center Tool for LPR Printing 26 4.4.5 Using Standard Windows Method for Raw TCP Printing 28 4.4.6 Using LevelOne MFP Control Center for Raw TCP Printing 30 4.4.7 Using Standard Windows Method for IPP Printing 31

CHAPTER5 ADDING PRINTERS IN UNIX/LINUX 33

5.1 Configuring Host File 33 5.2 Printing by LPD/LPR 33 5.3 Using FPS-3003 on BSD UNIX/Linux 34 5.4 Using RedHat Linux Printer System Manager 35

CHAPTER6 FILE SERVER FUNCTION 37

6.1 Preliminary 37 6.2 Storage Names 37 6.3 Connecting USB Mass Storage to FPS-3003 37 6.4 Supported Code Pages 38 6.5 Sharing Your USB Mass Storages 40 6.5.1 Use Shared Storages by SMB Method for Windows 40 6.5.2 Use Shared Storage by FTP Methods for Windows 41

CHAPTER7 SCAN SERVER FUNCTION 43

7.1 Connecting HP Office Jets to MFP Server 43 7.2 Using the Shared Scanner in Windows 43 7.2.1 Using LevelOne MFP Control Center Tool 43 7.2.2 Using Windows Applications 45

CHAPTER8 LEVELONE MFP CONTROL CENTER 47

8.1 Installing Your LevelOne MFP Control Center 47 8.2 Using LevelOne MFP Control Center 47 8.2.1 Use Tools of MFP Control Center 47 8.2.2 Display Server’s Status 48

Page 4 of the LevelOne Print Server (FPS-3003) user manual — CHAPTER5 ADDING PRINTERS IN UNIX/LINUX ...........................................33
Page 4 · click to enlarge
Page 4
Page 4 of the LevelOne Print Server (FPS-3003) user manual — CHAPTER5 ADDING PRINTERS IN UNIX/LINUX ...........................................33
Page 5 of the LevelOne Print Server (FPS-3003) user manual — Chapter1 Introduction
Page 5 · click to enlarge
Page 5

Chapter1 Introduction

Thank you for purchasing the FPS-3003 USB MFP server. This product is designed to connect your printers, USB Mass Storage/Memory Card Reader, and scanners of HP Office Jet series all-in-one printers (MFP), anywhere in your network, allowing all network users access to shared USB devices resources. 1.1 About this Manual This manual provides introductory information as well as detailed instructions on how to set up and manage the print server in various network environments. To fully benefit from this manual, you should be familiar with basic networking principles. These instructions are based on the settings in a new MFP server. To reload the Factory Parameters, you can perform a Factory Default, which will restore most of the settings. See “Factory Default” on page. 1.2 Support Services Should you require any technical assistance, please contact your product reseller. Or you can visit our website at http://www.level1.com for latest product information. This manual is subject to changed without notice.

Page 6 of the LevelOne Print Server (FPS-3003) user manual — Chapter2 Product Overview
Page 6 · click to enlarge
Page 6

Chapter2 Product Overview

  • 2.1 Package Contents Verify that nothing is missing from the FPS-3003 USB MFP server package by using the checking list below. Please contact your dealer if anything is missing or damaged. All packing materials are recyclable. Please confirm the items in the Package below:
  • One FPS-3003 USB/MFP Server.
  • One FPS-3003 MFP Control Center Software CD.
  • One AC Adaptor.
  • One Quick Installation Guide.

2.2 FPS-3003 USB MFP Server Product CD The FPS-3003 USB MFP Server Product CD provides an easy-to-use control center software for Windows PC, and user documents.

2.2.1 Start-up Procedures for Windows

If your computer is configured to auto start CDs, the FPS-3003 USB MFP Server Product CD will start automatically when inserted. You can also navigate to the CD and start the autorun.exe file from within the Windows file manager. 2.3 Physical Description

LevelOne Print Server (FPS-3003) — Chapter2 Product Overview diagram (page 6)
Fig. 2 · Chapter2 Product Overview

Power Link Status USB1 USB2

Show 6 more labels / short text on this page
Power Adaptor Connector · USB Port 1 · USB Port 2 · Init Button · Ethernet Connector · Indicators
Page 7 of the LevelOne Print Server (FPS-3003) user manual — Chapter2 Product Overview
Page 7 · click to enlarge
Page 7

2.3.1 Ethernet Connector

The network connector of FPS-3003 is designed for 10 Mbps or 100 Mbps Ethernet networks and connects to the network via a twisted pair category 5 cable (10baseT and 100baseTX) or better.

2.3.2 USB Host Ports

FPS-3003 has two USB host ports which are USB 1.1/2.0 low and full speed compliant and successfully tested with USB 1.1/2.0 printers, Mass Storage and HP Office Jet series printers (MFP).

2.3.3 Init Button

The Init button is used for:

„ printing a page of configuration report to check the connection

to the printer and showing the MFP server settings

„ performing a Factory Default of the MFP server, which will

restore most of the parameters and settings to factory default values

„ performing the new firmware upgrade using in fallback

2.3.4 Indicators

„ Power Indicator is lit while power is applied. If it is not lit, or if

it blinks, there is a problem with MFP server or Power Adapter.

„ Link Status is lit while network is applied. If it is not lit, it

indicates that the server does not connect to network.

„ Status Indicator blinks to indicate network activity.

„ USB1 Indicator is lit while an USB device connects to USB1

Port of MFP server. If it is not lit, or if it blinks, there is a problem with the USB device or the MFP server.

„ USB2 Indicator is lit while an USB device connects to USB2

Port of the MFP server. If it is not lit, or if it blinks, there is a problem with the USB device or the MFP server.

Page 8 of the LevelOne Print Server (FPS-3003) user manual — 2.4 Installation Methods
Page 8 · click to enlarge
Page 8

2.4 Installation Methods

2.4.1 Installation and Integration

Refer to the table below to select the appropriate installation method. LevelOne MFP Control Center tool is available on the FPS-3003 USB MFP Server Product CD or from LevelOne’s web site.

FunctionOSMethodDescription Print ServerWindowsStandard Windows Add Printer WizardInstallation of LPR, Raw TCP, Local Port Using SMB, and IPP MFP Control Center ToolInstallation of LPR, Raw TCP, Local Port Using SMB Unix/LinuxEdit /etc/printcap FileUsing vi or other editors to edit the printcap file RedHat Linux Printer System ManagerUsing X-Windows Interface to operate File ServerWindowsNoneDon’t need installation Unix/LinuxSambaUse smbclient in Samba Scan ServerWindowsMFP Control Center toolInstallation of SANE Client and SANE-Twain Driver Unix/LinuxSANE FrontendsUse SANE Applications such as XSANE

2.4.2 Configuration and Management

FPS-3003 USB MFP server can be configured and managed from its internal web pages, using HTTP or from user software: FPS-3003 MFP Control Center, using Windows. These web pages or PC tools offer you a management tool that is suitable for all supported network environments. 2.5 Features and Benefits

FPS-3003 provides the following features and benefits:

Page 9 of the LevelOne Print Server (FPS-3003) user manual — 2.4 Installation Methods
Page 9 · click to enlarge
Page 9

1. Reliability: The MFP server provides high performance and reliability combined with low power consumption. 2. Flexibility: The MFP server supports print/File/Scan sharing in all major computer systems and environments. 3. Easy to Install: The MFP server installs, operates and is managed in a reliable and easy fashion. 4. Security: You can assign administrator name and password to restrict login. 5. Monitoring: The MFP server’s web pages and user software allow you to continuously monitor MFP status. 6. Future Proof: The firmware stored in the MFP server Flash memory can be upgraded over the network. This allows you to quickly update and enhance its operational features when new MFP server software becomes available.

Page 10 of the LevelOne Print Server (FPS-3003) user manual — 3.1 Connecting the Hardware
Page 10 · click to enlarge
Page 10

Chapter3 Basic Installation

3.1 Connecting the Hardware

1. Make sure that your USB devices are switched off and that the MFP server’s Power Adapter is disconnected. 2. Connect the USB devices to the USB ports using the USB cables. 3. Connect the MFP server to the network using a twisted pair category 5 cable, 10baseT or 100baseTX. 4. Turn on the USB devices and make sure it is ready for use. 5. Connect the Power Adapter to the server. The power indicator will light up and USB1 and USB2 indicators will flash in turn. When the Link indicator lights up, the server is correctly connected to the network. When USB1 and USB2 indicators do not flash, the server starts to work normally. 6. If you connected USB HP printers to server, please press the Init button for 3 seconds on the server once to print a page of server configuration report. 3.2 Assigning an IP Address to the MFP Server

3.2.1 Preliminary

„ If you have a DHCP server on your network, your MFP server

will receive an IP address automatically. The IP address will then appear on user software: FPS-3003 MFP Control center or on the page of configuration report that you printed earlier. If your DHCP server does not give IP address to the server, the server will use the Factory IP address: 192.168.1.100.

„ If you are not working in a DHCP network, you need to set an

IP address of MFP server manually.

3.2.2 Ethernet Address

You do not need to know the Ethernet address of your FPS-3003 USB MFP server for assigning an IP address to it. MFP Control Center software can automatically search MFP servers and list their Ethernet

Page 11 of the LevelOne Print Server (FPS-3003) user manual — Chapter3 Basic Installation
Page 11 · click to enlarge
Page 11

addresses. Besides, you can find Ethernet address that is located on the backside label of the server.

3.2.3 IP Address

Unless you are assigning an IP address using DHCP, you must obtain an unused IP address from your network administrator.

3.2.4 Methods for Setting the IP Address

You can set the IP address of your FPS-3003 USB MFP server using one of the following methods, depending on your network operating environment:

„ Automatic IP Address Assignment

„ Manual IP Address Assignment

3.2.5 Host Names and Host Name Rules

The host name of the FPS-3003 USB MFP server is specified by “FPS-3003”in Factory Parameter. If you put two or more KMFP servers in your local area network, to avoid using same host names you have to change the host names by LevelOne MFP Control Center or server’s web pages. If your host name is longer than 15 characters, FPS-3003 USB MFP server limits the length of host name to 15 characters.

3.2.6 Set the IP Address Using DHCP

Follow the instructions below to get an IP address using DHCP:

1. Edit or create a scope in the DHCP manager of the DHCP daemon. The entries included in this scope should contain the following parameters:

„ range of IP addresses

„ default router IP address

„ DNS server IP address

„ lease duration 2. Activate the scope. The MFP server automatically gets the DHCP parameters. If you are using DNS, you may include at least one DNS server IP address in the DHCP scope or manually set DNS server IP in MFP server’s web pages or LevelOne MFP Control

„ subnet mask

Page 12 of the LevelOne Print Server (FPS-3003) user manual — Chapter3 Basic Installation
Page 12 · click to enlarge
Page 12

Center tool.

3.2.7 Set the IP Address Using LevelOne MFP Control Center

1. Install LevelOne MFP Control Center. LevelOne MFP Control Center is available in the FPS-3003 USB MFP Server Product CD. 2. Start LevelOne MFP Control Center and Auto-searching MFP server window will appear. 3. If the tool finds MFP servers in your local area network, then you have to select a MFP server from the server list.
LevelOne Print Server (FPS-3003) — Chapter3 Basic Installation diagram (page 12)
Fig. 3 · Chapter3 Basic Installation
4. Double click the highlight list and type the server’s administrator (default: admin ) and password (default: admin ).
Page 13 of the LevelOne Print Server (FPS-3003) user manual — Chapter3 Basic Installation
Page 13 · click to enlarge
Page 13
LevelOne Print Server (FPS-3003) — Chapter3 Basic Installation diagram (page 13)
Fig. 4 · Chapter3 Basic Installation
5. After you login successfully, from the Server menu, select TCP/IP. The Set IP Address dialog appears.
LevelOne Print Server (FPS-3003) — Chapter3 Basic Installation diagram (page 13)
Fig. 5 · Chapter3 Basic Installation

6. Click the button that corresponds to your choice of IP setting method (static or dynamic using DHCP). When assigning a static IP address you also have to define Subnet Mask and Default Gateway. If you choose Automatically get IP by DHCP, you can use desired DNS by clicking the Manual DNS button and manually assigning a DNS. 7. Click Apply to save your settings. And the server will reboot. 8. You have now finished the procedure of setting the IP address.

3.2.8 Set the IP Address Using Server’s Web Pages

Page 14 of the LevelOne Print Server (FPS-3003) user manual — Chapter3 Basic Installation
Page 14 · click to enlarge
Page 14
1. If you don’t know the current IP of server, you have to do the Step1~Step4 of Set the IP Address Using LevelOne MFP Control Center. 2. You can see the IP address of MFP server in the server list. Open IE Browser and type server’s IP address or click the Home Icon of LevelOne MFP Control center.
LevelOne Print Server (FPS-3003) — Chapter3 Basic Installation diagram (page 14)
Fig. 6 · Chapter3 Basic Installation
3. Go to the web page and click TCP/IP icon.
LevelOne Print Server (FPS-3003) — Chapter3 Basic Installation diagram (page 14)
Fig. 7 · Chapter3 Basic Installation
4. Login your administrator (default: admin ) and password (default: admin ). 5. Click the button that corresponds to your choice of IP setting methods (static or dynamic using DHCP). When assigning a static IP address you also have to define Subnet Mask and Default Gateway.
Page 15 of the LevelOne Print Server (FPS-3003) user manual — Chapter3 Basic Installation
Page 15 · click to enlarge
Page 15
LevelOne Print Server (FPS-3003) — Chapter3 Basic Installation diagram (page 15)
Fig. 8 · Chapter3 Basic Installation
6. Click Submit to save your settings. And the server will reboot. You have now finished the procedure of setting the IP address. 3.3 Naming Your USB Devices

3.3.1 Printer Names

„ Default Printer Name

1. The system will set the printer model names as the default printer names. The system only allows a 12 characters long USB device name. For example, the printer model name is “psc 1300 series” and then the default printer name will be set as “psc 1300 ser”. 2. If system can not get the printer model (For ex, you use some parallel printers and use Parallel-to-USB cables to connect the printers), the default printer names are set as: USB1_Printer and USB2_Printer with respect to USB1 port and USB2 port.

„ Set Printer Name

You can set yourself printer names by LevelOne MFP Control Center or server’s web pages.

i. Using LevelOne MFP Control Center 1. Start LevelOne MFP Control Center and Auto-searching MFP server window will appear. 2. If the tool finds MFP servers in your local area network,

Page 16 of the LevelOne Print Server (FPS-3003) user manual — Chapter3 Basic Installation
Page 16 · click to enlarge
Page 16

then you have to select a MFP server from the server list. 3. Double click the highlight list and type the server’s administrator (default: admin) and password (default: admin). 4. After you login successfully, from the Server menu, select USB Device Information. The Set USB Device Information dialog appears.

LevelOne Print Server (FPS-3003) — Chapter3 Basic Installation diagram (page 16)
Fig. 9 · Chapter3 Basic Installation
5. Set your printer names in Printer Name box and then click Apply .

ii. Using Server’s Web Pages 1. Go to the web page and click USB Device Information icon. 2. Login your administrator (default: admin) and password (default: admin).

Page 17 of the LevelOne Print Server (FPS-3003) user manual — Chapter3 Basic Installation
Page 17 · click to enlarge
Page 17
LevelOne Print Server (FPS-3003) — Chapter3 Basic Installation diagram (page 17)
Fig. 10 · Chapter3 Basic Installation
3. Set your printer names in Printer Name box and then click Apply .

3.3.2 Storage Names

The local drives of the two storages in USB1 port and USB2 port are named as USBx_DxPx, where USBx represents the USBx port, Dx represents the the x-th Disk (in particular to card reader plugging in multiple cards) and Px represents the x-th partition.

3.3.3 Scanner Names

The name of connected scanner of HP office jet series consists of the “vender” + “model”. For example, the scanner name of HP PSC 1310 office jet is named as “HP PSC 1310 series”.

Page 18 of the LevelOne Print Server (FPS-3003) user manual — Chapter4 Adding Printers in Windows
Page 18 · click to enlarge
Page 18

Chapter4 Adding Printers in Windows

4.1 Overview of Installation Methods This chapter describes how to add network printers to Windows PC.

Table List for Installing Network Printer

Windows 98, ME, 2000,XP and 2003

Standard Windows Add Printer Wizard SMB Printing

LevelOne MFP Control Center’s Add Printer

IPP Printing Standard Windows Add Printer Wizard Standard Windows Add Printer Wizard LPR Printing

Windows 2000, XP and 2003

LevelOne MFP Control Center’s Add Printer

Standard Windows Add Printer Wizard

LevelOne MFP Control Center’s Add Printer

Steps for Installing Network Printer

Step 1 Step 2 Step 3

Set up Local Window

Step 4 Step 5 Step 6

Add Network Printer by - Windows Standard

Method - PC User Software

Show 14 more labels / short text on this page
Windows Platform · Printing Protocols · Method · Raw TCP Printing · Connect Your Printer · Connect MFP Server · Printer Driver · to MFP Server · to Network · Configure Your MFP · Turn on Your · Server · Printer and MFP · Server
Page 19 of the LevelOne Print Server (FPS-3003) user manual — PC
Page 19 · click to enlarge
Page 19

4.2 Connecting FPS-3003 MFP Server To configure your server correctly, you have to know your server connecting to what type of network topology.

4.2.1 MFP Server and Windows PC on Same LAN

LevelOne Print Server (FPS-3003) — 4.2.1 MFP Server and Windows PC on Same LAN diagram (page 19)
Fig. 11 · 4.2.1 MFP Server and Windows PC on Same LAN

LAN HUB/Switch MFP Server

PC

PC

4.2.2 MFP Server and Windows PC on Different LANs

1. Wired Windows PC across Internet
LevelOne Print Server (FPS-3003) — PC diagram (page 19)
Fig. 12

LAN HUB/Switch MFP Server

PC

Show 6 more labels / short text on this page
USB Printer · Router · Internet · Router · Switch · USB Printer
Page 20 of the LevelOne Print Server (FPS-3003) user manual — 4.2.1 MFP Server and Windows PC on Same LAN
Page 20 · click to enlarge
Page 20
2. Wireless Windows PC
LevelOne Print Server (FPS-3003) — 4.2.1 MFP Server and Windows PC on Same LAN diagram (page 20)
Fig. 13 · 4.2.1 MFP Server and Windows PC on Same LAN

LAN HUB/Switch MFP Server

4.3 Setting up Local Windows Printer Driver You are advised to install your Windows printer driver in advance. For most printers, you can install the printer drivers as the following procedure:

1. Click Start, click Control Panel, click Printers and Other Hardware, and then click Printers and Faxes. 2. Double click Add Printer to start the Add Printer Wizard, and then click Next. 3. Click Local printer, clear the Automatically detect and install my Plug-n-Play printer check box to avoid having to wait for the completion of another printer search, and then click Next. If you leave this option selected, Windows will attempt to find the printer itself and figure out what kind it is. If Windows does not find the printer, the wizard will continue as described in this task. 4. Select a Windows driver for your printer. Click Next. 5. Choose whether you want to share the printer with other network users. Do you want to print a test page? Select the appropriate radio button and click Next and Finish. 4.4 Adding Network Printers in Windows Follow the instructions below to use the standard Windows Add Printer

Wireless AP Router · Wireless PC · USB Printer

Page 21 of the LevelOne Print Server (FPS-3003) user manual — # If your server is running on a different LAN than your
Page 21 · click to enlarge
Page 21

Wizard and LevelOne MFP Control Center for adding a network printer in Windows 98 SE, ME, 2000, XP and 2003. Before adding a network printer, you are advised to install the local Windows printer driver in advance.

4.4.1 Using Standard Windows Methods for SMB Printing

Windows PlatformWindows 98SE, ME, 2000, XP and 2003
1. Open Printers and Faxes 2. Right-click the printer for which you want to change settings, and then click Properties. 3. Click the Ports tab. 4. Clear Enable bidirectional support and click add port , and then click Local Port in the Port type section.

In the Port Name box, type the path to the printer in the following format: ”\\ server’s host name\printer name” or ”\\ server’s IP address \printer name” (Please refer to server’s web pages or LevelOne MFP Control Center tool to know exact path). For example: if you set server’s host name as FPS-3003 and printer name (USB1 port) as psc 1300 ser, then the network path is expressed as: \\FPS-3003\psc 1300 ser

LevelOne Print Server (FPS-3003) — # If your server is running on a different LAN than your diagram (page 21)
Fig. 14 · # If your server is running on a different LAN than…

# If your server is running on a different LAN than your

windows PC such as wireless Windows PC, you must type IP address in Port Name box. 5. Click OK, and then select a Windows driver for your printer. If you already have the printer’s driver installed, you will be asked whether to keep it or to replace it. Click Next. 6. Choose whether you want to share the printer with other network users. Do you want to print a test page? Select the appropriate radio button and click Next and Finish.

Protocol

Page 22 of the LevelOne Print Server (FPS-3003) user manual — # If your server is running on a different LAN than your
Page 22 · click to enlarge
Page 22

4.4.2 Using LevelOne MFP Control Center Tool for SMB

Windows PlatformWindows 98, ME, 2000, XP and 2003
1. Start LevelOne MFP Control Center, select your MFP server and click Add Printer . 2. Select USB1 Port or USB2 Port to add the printer in Add the printer box, choose to use host name or IP address to represent MFP server in Select IP Address or Host Name in printer port box, and select the network printing protocol of Printing with Network Path (SMB) .
LevelOne Print Server (FPS-3003) — # If your server is running on a different LAN than your diagram (page 22)
Fig. 15 · # If your server is running on a different LAN than…

# If your server is running on a different LAN than your Windows PC such as wireless Windows PC, you must choose IP address in Select IP address or Host Name in printer port box.

3. Click Apply . 4. Select the desired printer driver and click Set Port to Printer .

Printing

Page 23 of the LevelOne Print Server (FPS-3003) user manual — Protocol
Page 23 · click to enlarge
Page 23
LevelOne Print Server (FPS-3003) — Protocol diagram (page 23)
Fig. 16 · Protocol
5. If you can not find any printer driver in Printer List, please install your printer driver first or click Add New Printer to install the printer driver.

4.4.3 Using Standard Windows Methods for LPR Printing

Protocol

Windows PlatformWindows 2000, XP and 2003
1. Open Printers and Faxes 2. Right-click the printer for which you want to change settings, and then click Properties/ports 3. Clear Enable bidirectional support and click Add port , and then click Standard TCP/IP Port from the dropdown and click New port . 4. The " Add Standard TCP/IP Printer Port Wizard " will pop up and click Next .
Page 24 of the LevelOne Print Server (FPS-3003) user manual — Protocol
Page 24 · click to enlarge
Page 24
LevelOne Print Server (FPS-3003) — Protocol diagram (page 24)
Fig. 17 · Protocol
5. In the Printer Name or IP Address box, type host name of the MFP server (default: FPS-3003) or IP address of MFP server. In the Port Name box, type your desired names or USB1_LPR or USB2_LPR for printer connected to USB1 port and USB2 port, respectively.
LevelOne Print Server (FPS-3003) — Protocol diagram (page 24)
Fig. 18 · Protocol

# If your server is running on a different LAN than your Windows PC such as wireless Windows PC, you must type server’s IP address in Printer Name or IP Address box. 6. Click Next.

Page 25 of the LevelOne Print Server (FPS-3003) user manual — Protocol
Page 25 · click to enlarge
Page 25
7. Click Custom/settings .
8. Click Settings and confirm that the settings are as below. The queue names are USB1_LQ , USB2_LQ for USB1 port 1 and USB2 port, respectively.
Page 26 of the LevelOne Print Server (FPS-3003) user manual — Printing
Page 26 · click to enlarge
Page 26
LevelOne Print Server (FPS-3003) — Printing diagram (page 26)
Fig. 19 · Printing
9. Click OK to finish.
LevelOne Print Server (FPS-3003) — Printing diagram (page 26)
Fig. 20 · Printing

4.4.4 Using LevelOne MFP Control Center Tool for LPR

Printing

Windows PlatformWindows 2000, XP and 2003
1. Start LevelOne MFP Control Center, select your MFP server and click Add Printer .
LevelOne Print Server (FPS-3003) — Printing diagram (page 26)
Fig. 21 · Printing
Page 27 of the LevelOne Print Server (FPS-3003) user manual — Printing
Page 27 · click to enlarge
Page 27
2. Select USB1 Port or USB2 Port to add the printer in Add the printer box, choose to use host name or IP address to represent MFP server in Select IP address or Host Name in printer port box, and select the network printing protocol of Printing with LPR (Line Printer Remote) .
LevelOne Print Server (FPS-3003) — Printing diagram (page 27)
Fig. 22 · Printing

# If your server is running on a different LAN than your Windows PC such as wireless Windows PC, you must choose IP address in Select IP address or Host Name in printer port box. 3. Click Apply. 4. Select the desired printer driver and click Set Port to Printer.

Page 28 of the LevelOne Print Server (FPS-3003) user manual — 4.4.5 Using Standard Windows Method for Raw TCP Printing
Page 28 · click to enlarge
Page 28
LevelOne Print Server (FPS-3003) — 4.4.5 Using Standard Windows Method for Raw TCP Printing diagram (page 28)
Fig. 23 · 4.4.5 Using Standard Windows Method for Raw TCP Prin…
5. If you can not find any printer driver in Printer List, please install your printer driver first or click Add New Printer to install the printer driver.

4.4.5 Using Standard Windows Method for Raw TCP Printing

Windows PlatformWindows 2000, XP and 2003

1. Open Printers and Faxes 2. Right-click the printer for which you want to change settings, and then click Properties 3. Clear Enable bidirectional support and click Add port, and then click Standard TCP/IP Port from the dropdown and click New port. 4. The "Add Standard TCP/IP Printer Port Wizard" will pop up and click Next. 5. In the Printer Name or IP Address box, type host name of the MFP server (default: FPS-3003) or IP address of MFP server. In the Port Name box, type USB1_RAW or USB2_RAW for printer connected to USB1 port and USB2 port, respectively.

Page 29 of the LevelOne Print Server (FPS-3003) user manual — 4.4.5 Using Standard Windows Method for Raw TCP Printing
Page 29 · click to enlarge
Page 29

# If your server is running on a different LAN than your Windows PC such as wireless Windows PC, you must type server’s IP address in Printer Name or IP Address box. 6. Click Next. 7. Click Custom/settings. 8. The click Settings and confirm that the settings are as below. The default Port Number values are 9100, 9101 for USB port 1 and USB port 2, respectively. Refer to server’s web pages or LevelOne MFP Control Center tool, you can get exact values.

LevelOne Print Server (FPS-3003) — 4.4.5 Using Standard Windows Method for Raw TCP Printing diagram (page 29)
Fig. 24 · 4.4.5 Using Standard Windows Method for Raw TCP Prin…
9. Click OK and then Finish.
LevelOne Print Server (FPS-3003) — 4.4.5 Using Standard Windows Method for Raw TCP Printing diagram (page 29)
Fig. 25 · 4.4.5 Using Standard Windows Method for Raw TCP Prin…
Page 30 of the LevelOne Print Server (FPS-3003) user manual — Printing
Page 30 · click to enlarge
Page 30

4.4.6 Using LevelOne MFP Control Center for Raw TCP

Printing

Windows PlatformWindows 2000, XP and 2003
1. Start LevelOne MFP Control Center, select your MFP server and click Add Printer . 2. Select USB1 Port or USB2 Port to add the printer in Add the printer box, choose to use or IP address to represent MFP server in Select IP Address or Host Name in printer port box, and select the network printing protocol of Print with Raw TCP Mode .
LevelOne Print Server (FPS-3003) — Printing diagram (page 30)
Fig. 26 · Printing

# If your server is running on a different LAN than your Windows PC such as wireless Windows PC, you must choose IP address in Select IP Address or Host Name in printer

Page 31 of the LevelOne Print Server (FPS-3003) user manual — 4.4.7 Using Standard Windows Method for IPP Printing
Page 31 · click to enlarge
Page 31

port box. 3. Click Apply. 4. Select the desired printer driver and click Set Port to Printer.

LevelOne Print Server (FPS-3003) — 4.4.7 Using Standard Windows Method for IPP Printing diagram (page 31)
Fig. 27 · 4.4.7 Using Standard Windows Method for IPP Printing
5. If you can not find any printer driver in Printer List, please install your printer driver first or click Add New Printer to install the printer driver.

4.4.7 Using Standard Windows Method for IPP Printing

Windows PlatformWindows 98 SE, ME, 2000, XP and 2003
1. Click Start, click Control Panel , click Printers and Other Hardware, and then click Printers and Faxes. 2. Double click Add Printer to start the Add Printer Wizard, and then click Next.
3. In this window, select A network printer, or a printer attached to another computer and click Next .
Page 32 of the LevelOne Print Server (FPS-3003) user manual — # If your server is running on a different LAN than your
Page 32 · click to enlarge
Page 32
LevelOne Print Server (FPS-3003) — 4.4.7 Using Standard Windows Method for IPP Printing diagram (page 32)
Fig. 28 · 4.4.7 Using Standard Windows Method for IPP Printing
4. Click the Next button. On the next window, select Connect to a printer on the Internet or on a home or office network. In the URL: field, enter the following to connect to MFP server: http://sercver’s host name /printer name or http:/server’s IP address /printer name For example, http://FPS-3003/psc 1310 ser

# If your server is running on a different LAN than your

windows PC such as wireless Windows PC, you must type IP address in URL: Field.

5. Click Next and then continue Windows Add Printer Wizard.
Page 33 of the LevelOne Print Server (FPS-3003) user manual — Chapter5 Adding Printers in Unix/Linux
Page 33 · click to enlarge
Page 33

Chapter5 Adding Printers in Unix/Linux

This chapter describes how to add network printers to Unix/Linux PC. 5.1 Configuring Host File If using IP administration system like DNS, manually registering the host name and IP address may be not required. Otherwise, you have to edit hosts file and contact your network administrator.

1. Log in to Linux machine by “root”. # login root 2. Register FPS-3003 MFP server’s host name and IP address to /etc/hosts file. To edit host file, use an editor, e.g. “vi”. Example: The IP address is “192.168.1.100”, host name is “FPS-3003” 192.168.1.1 dns # DNS Server 192.168.1.2 mail # Mail Server 192.168.1.100 FPS-3003 # MFP-Server 3. Switch on the MFP server. Verify the network connection by using ping command. # ping FPS-3003 If there is no response or error is indicated, there may be problems with IP address configuration, host file editing or network status. Please contact your network administrator. 5.2 Printing by LPD/LPR This section explains how to print using LPD protocol of TCP/IP. For further information on “lpr” and “lp” commands, refer to your workstation manual. LPD Protocol: LPD (Line Printer Daemon) is a protocol that enables you to execute printing to a printer on the network. Remote-Printer Queue: FPS-3003 has two remote printer queues USB1_LQ and USB2_LQ with respect to USB port 1 and UB port2. To print files using a printer driver, use “lp” or “lpr”.

Page 34 of the LevelOne Print Server (FPS-3003) user manual — 5.3 Using FPS-3003 on BSD UNIX/Linux
Page 34 · click to enlarge
Page 34

5.3 Using FPS-3003 on BSD UNIX/Linux

1. Log in to the BSD Unix machine through “root”. # login root 2. Register the FPS-3003 MFP server to /etc/printcap file. Example: To register the printer of USB1 port by the printer name “Printer1”. Printer1:\ ---(A)

:lp=:rm=FPS-3003:rp=USB1_LQ:\ ---(B) :sd=/var/spool/lpd/Printer1:\ ---(C) :lf=/var/spool/lpd/Printer1/Printer1_errs: ---(D) where

(A) Describes the printer name. (B) lp: Device file name to connect printer. No name designation required on the network. rm: Host name for the remote printer. Type the host name registered to /etc/hosts file. rp: Remote printer name. Please input the remote printer queue name.

(C) sd: Spool directory name. It must be the absolute path. (D) lf: Error log file name. It must be the absolute path. 3. Create the spool directory and error log file registered to /etc/printcap file. Example: To create the spool directory “Printer1” and error log file “Printer1_errs”. # mkdir /var/spool/lpd/Printer1 Create the spool directory # touch /var/spool/lpd/Printer1/Printer1_errs Create the error log file # chown -R daemon /var/spool/lpd/Printer1 Change the owner to daemon # chgrp -R daemon /var/spool/lpd/Printer1 Change the group to daemon 4. Start Printing.

A. Use the "lp" command.

- # lp -d Printer1 <Print file name> - # lp -d Printer2 <Print file name>

Page 35 of the LevelOne Print Server (FPS-3003) user manual — 5.4 Using RedHat Linux Printer System Manager
Page 35 · click to enlarge
Page 35

B. Use the “lpr” command.

- # lpr -P Printer1 <print file name> - # lpr -P Printer2 <Print file name>

5.4 Using RedHat Linux Printer System Manager

In the RedHat x-window user interface, do the steps as follows:

1. Form the Start menu, choose Programs -> Administration -> Click Printer Tool. Windows will display the RHS Linux Print System Manager folder. 2. Click on the ADD button in the RHS Linux Print System Manager folder. Windows will display the Add a Printer Entry folder. 3. You will now be asked to specify which Printer type you are using, select the "Remote Unix (lpd) Queue" option. 4. Click the OK button. Windows will display the Under Edit Remote Unix(lpd) queue Entry folder 5. In the Under Edit Remote Unix(lpd) queue Entry folder, enter values for the fields as follows:

- Input Names (name1[name2]*): Printer1 or Printer2 (any name) - Spool Directory: /var/spool/lpd/Printer1 or Printer2 - File Limit in Kb (0=no limit): 0 - Remote Host: FPS-3003 or IP address of MFP server - Remote Queue: USB1_LQ or USB2_LQ - Input Filter [select] : select the printer driver

6. Click OK . In the RHS Linux Print System Manager folder, select Tests in the menu bar. 7. Start printing:

A. Use the "lp" command.

- # lp -d Printer1 <Print file name> - # lp -d Printer2 <Print file name>

Page 36 of the LevelOne Print Server (FPS-3003) user manual — 5.4 Using RedHat Linux Printer System Manager
Page 36 · click to enlarge
Page 36

B. Use the “lpr” command.

- # lpr -P Printer1 <print file name> - # lpr -P Printer2 <Print file name>

Page 37 of the LevelOne Print Server (FPS-3003) user manual — FPS-3003
Page 37 · click to enlarge
Page 37

Chapter6 File Server Function

This chapter describes the file server function of FPS-3003 MFP server which allows USB storage devices to be shared across a network by using SMB: NetBIOS over TCP/IP and FTP protocol. 6.1 Preliminary 1. This product supports a file format of FAT12/16/32. It will not support a drive formatted by NTFS, etc. 2. LevelOne technology is not responsible for the loss or corruption of data in memory devices, including hard disk; LevelOne is not responsible for the leak, manipulation, loss, or corruption of data in memory devices connected to MFP server after unauthorized access. 3. In order to use the USB Mass Storage device connected to the MFP server, the SMB protocol or FTP protocol must be set up. 4. This product does not support to magnet optical drive devices such as CD/DVD. 5. This product allows shared two USB storage devices over the network in Windows through the USB ports. 6. This product does not support the USB devices through USB hub. 6.2 Storage Names The local drives of the two storages in USB1 port and USB2 port are named as USBx_DxPx, where USBx represents the USBx port, Dx represents the the x-th Disk and Px represents the x-th partition. 6.3 Connecting USB Mass Storage to FPS-3003

LevelOne Print Server (FPS-3003) — Chapter6 File Server Function diagram (page 37)
Fig. 29 · Chapter6 File Server Function

FPS-3003

LAN HUB/Switch · Storage

Page 38 of the LevelOne Print Server (FPS-3003) user manual — 6.4 Supported Code Pages
Page 38 · click to enlarge
Page 38

6.4 Supported Code Pages

- What is codepage? Used by the system to encode and interpret string characters. Codepage formats are not the same for each language. Some languages, such as Japanese have multibyte characters, while others, such as English and German, need only one byte to represent each character. - Filename Encoding of FAT File System This is known as an 8.3 file name, a short file name using code page encoding. The FAT file system also supports file names that can be up to 255 characters long. This is known as a long file name using Unicode (UTF-16) encoding. - Configuring FPS-3003 Codepages MFP Server supports Windows Codepages. If users want to communicate files with FPS-3003 MFP server, they have to set their MFP server code page to be same as the codepage that their Windows PC is using. Users can use the following methods to set MFP server codepage.

i. Using LevelOne MFP Control Center

1. Start LevelOne MFP Control Center and Auto-searching MFP server window will appear. 2. If the tool finds MFP servers in your local area network, then you have to select a MFP server from the server list. 3. Double click the highlight list and type the server’s administrator (default: admin ) and password (default: admin ). 4. After you login successfully, setting General Configuration dialog appears.
Page 39 of the LevelOne Print Server (FPS-3003) user manual — 6.4 Supported Code Pages
Page 39 · click to enlarge
Page 39
LevelOne Print Server (FPS-3003) — 6.4 Supported Code Pages diagram (page 39)
Fig. 30 · 6.4 Supported Code Pages
5. Select your code page form File Server Code Page box and click Apply .

ii. Using Server’s Web Pages

1. Go to the web page, click Config -> General Configuration icon. 2. Login your administrator (default: admin ) and password (default: admin ). 3. After you login successfully, setting General Configuration dialog appears.
Page 40 of the LevelOne Print Server (FPS-3003) user manual — 6.5.1 Use Shared Storages by SMB Method for Windows
Page 40 · click to enlarge
Page 40
LevelOne Print Server (FPS-3003) — „ FTP diagram (page 40)
Fig. 31
4. Select your code page form File Server Code Page box and click Apply .

6.5 Sharing Your USB Mass Storages You can use the following protocols to share your USB Mass Storages in network:

„ SMBNetBIOS over TCP/IP

„ FTP

# Prior to using the above protocols, you must select Enable SMB Print/File Server and Enable FTP Server options in Set Supported Protocols box.

6.5.1 Use Shared Storages by SMB Method for Windows

1. Connect a USB storage device to this product. 2. Select My Network Places 3. Click Display the Computers of Workgroup 4. Double click Microsoft Windows Network icon. 5. Double click the Workgroup that MFP server belongs to. The default Workgroup name is “ LevelOne ”. You can refer to
Page 41 of the LevelOne Print Server (FPS-3003) user manual — 6.5.2 Use Shared Storage by FTP Methods for Windows
Page 41 · click to enlarge
Page 41

LevelOne MFP Control Center or server’s web pages to get it. You will see that the MFP server will be displayed as the default host name "FPS-3003" or the host name that you have set. 6. If you can not find Workgroup name of MFP server in Microsoft Windows Network, you can select Search Computer in My Network Places and type the hostname of MFP server (ex, default host name “FPS-3003” ) to find it. 7. Double click this host name icon. The folders will be displayed as USB1_DxPx, and USB2_DxPx where Dx represents the x-th disk and Px represents the x-th partition with respect to USB1 port and USB2 port. 8. Double click the one of folders to open the folders over the network.

6.5.2 Use Shared Storage by FTP Methods for Windows

i. Use Microsoft IE to the shared USB Mass Storages

1. Open Microsoft IE 2. In Web Address List, type command: “ftp://server’s host name“ or “ftp://server’s IP address”. If you have changed the default FTP port : 21 to the new value, you have to add the new port number in the tail of command as “ftp://server’s host name: ftp port” or “ftp://server’s IP address: ftp port” 3. If you clear Enable FTP Authentication in Set Supported protocols, you login to the FTP server as anonymous login; otherwise you have to type user name and password to login to the server. 4. The shared folders will be listed in IE. 5. Perform Paste, Remove or Copy the files to the shared folders.

ii. Use Microsoft Dos’s FTP client

1. Type Dos command as “ftp” 2. Type “ open server’s host name ” or “ open server’s IP address ”. If you have changed the default FTP port : 21 to the new value, you have to add the new port number in the tail of command as “ open server’s host name ftp port” or “ open server’s IP address ftp port ”
Page 42 of the LevelOne Print Server (FPS-3003) user manual — 6.5.2 Use Shared Storage by FTP Methods for Windows
Page 42 · click to enlarge
Page 42
3. If you clear Enable FTP Authentication in Set Supported protocols, you login to the FTP server as anonymous login; otherwise you have to type user name and password to login to the server. 4. Perform FTP commands to use this FTP server.
Page 43 of the LevelOne Print Server (FPS-3003) user manual — HP MFP
Page 43 · click to enlarge
Page 43

Chapter7 Scan Server Function

This chapter explains how to use the scan server function of this product. The scan server function enables a USB scanner of HP OJ series, connected to this product, to be shared as a network scanner. The scan server function is available in any platform that can use SANE client. 7.1 Connecting HP Office Jets to MFP Server er

LevelOne Print Server (FPS-3003) — Chapter7 Scan Server Function diagram (page 43)
Fig. 32 · Chapter7 Scan Server Function

HP MFP

FPS-3003

7.2 Using the Shared Scanner in Windows

7.2.1 Using LevelOne MFP Control Center Tool

1. Start LevelOne MFP Control Center, select your MFP server, and click LevelOne Network Scanner.
LevelOne Print Server (FPS-3003) — HP MFP diagram (page 43)
Fig. 33

LAN HUB/Switch · Scanner

Page 44 of the LevelOne Print Server (FPS-3003) user manual — Chapter7 Scan Server Function
Page 44 · click to enlarge
Page 44
2. Select your scanner for USB1 port or USB2 port.
LevelOne Print Server (FPS-3003) — Chapter7 Scan Server Function diagram (page 44)
Fig. 34 · Chapter7 Scan Server Function

3. Set the options. The options are defined as follows: - Source: choose flatbed scanning or scrolledbed scanning - Mode: choose lineart (black/white), Gray and color mode - Resolution: choose the image resolution - Contrast: tune the contrast of the image - Brightness: tune brightness of the image - Range: define the scanning range of the image 4. Click Preview button 5. Adjust the window size to be scanned 6. Click Scan button 7. Save as your images to the file

Page 45 of the LevelOne Print Server (FPS-3003) user manual — 7.2.2 Using Windows Applications
Page 45 · click to enlarge
Page 45

7.2.2 Using Windows Applications

Prior to using scanning functions in Windows applications such as MS Word, Photoshop …etc, you have to install network scanner’s TWAIN driver in advance. When you install LevelOne MFP Control Center tool, it will also install this TWAIN driver. Example: Using Photoshop 1. Start Photoshop, click File ->Import->FPS-3003 Network Scanner

LevelOne Print Server (FPS-3003) — 7.2.2 Using Windows Applications diagram (page 45)
Fig. 35 · 7.2.2 Using Windows Applications
2. Select a server’s IP address or type a server IP address in Server Information box. You can click Search Server button

to search existing MFP servers in your network.

LevelOne Print Server (FPS-3003) — 7.2.2 Using Windows Applications diagram (page 45)
Fig. 36 · 7.2.2 Using Windows Applications
Page 46 of the LevelOne Print Server (FPS-3003) user manual — 7.2.2 Using Windows Applications
Page 46 · click to enlarge
Page 46
3. Click Connect to Network Scanner button

in Server Information box

LevelOne Print Server (FPS-3003) — 7.2.2 Using Windows Applications diagram (page 46)
Fig. 37 · 7.2.2 Using Windows Applications
4. Select your scanner in Server Information box. 5. Click Preview button 6. Adjust the window size to be scanned 7. Click Scan button
Page 47 of the LevelOne Print Server (FPS-3003) user manual — 8.2.1 Use Tools of MFP Control Center
Page 47 · click to enlarge
Page 47

Chapter8 LevelOne MFP Control Center

This chapter describes how to use LevelOne MFP Control Center in your Windows. 8.1 Installing Your LevelOne MFP Control Center 1. Click Install Product button.

LevelOne Print Server (FPS-3003) — Chapter8 LevelOne MFP Control Center diagram (page 47)
Fig. 38 · Chapter8 LevelOne MFP Control Center
2. Click Next , if you see Next button in installation windows. 3. Click Finish. 8.2 Using LevelOne MFP Control Center

8.2.1 Use Tools of MFP Control Center

You can use the following tools to help you using the MFP server:

: renew to auto search the existing MFP

: search the MFP server by IP address

: refresh the highlight list’s server status

„ Go to web

: go to web pages of the highlight list’s server

: perform network scanner function of

the highlight list’s server

Show 5 more labels / short text on this page
„ Auto Search · servers in network · „ IP Search · „ Refresh · „ Network Scanning
Page 48 of the LevelOne Print Server (FPS-3003) user manual — Š TCP/IP
Page 48 · click to enlarge
Page 48

: perform add printer function of the highlight

8.2.2 Display Server’s Status

You can start LevelOne MFP Control Center and select your MFP server to see the server status which includes Host Information, TCP/IP, USB Devices Status and Supported Protocols.

8.2.3 Set up Server’s Configuration

Š Set Host InformationYou have to set some

information for networking using SMB protocol: 5 Comment: optionally set to describe the server 5 Host Name: the name to represent the server for Windows networking using SMB protocol 5 Workgroup: the SMB workgroup name that the server belongs to. Š File Server Code Page: You have to select your code

page while operating network file sharing. Generally, the criteria of choosing code page are based on your Windows code page. For example, if your Windows code page is Traditional Chinese, you have to select Traditional Chinese (Big5) in server. Please refer to Chapter 6 File Server Function.

„ USB Device InformationYou can set printer names and

display some information of USB mass storages and scanners. Please refer to Chapter 4, Chapter 6 and Chapter 7.

„ TCP/IPYou have to set the server’s TCP/IP configuration to

connect TCP/IP network. Please see Chapter 3 Basic Installation for more details.

„ Supported ProtocolsThe server supports the following

TCP/IP protocols:

Š TCP/IP

5 Enable LPR (Line Printer Remote) Printing: select or

„ Add Printer · list’s server · „ General Configuration

Page 49 of the LevelOne Print Server (FPS-3003) user manual — 8.2.3 Set up Server’s Configuration
Page 49 · click to enlarge
Page 49

clear Enable LPR Printing support. It is enabled in Factory Default. 5 Enable IPP Printing: select or clear Enable IPP Printing support. It is enabled in Factory Default. 5 Enable Raw TCP Printing: select or clear Enable Raw TCP Printing support. It is enabled in Factory Default and users may set the protocol’s TCP ports as following boxes: - TCP Port 1: set TCP port for the printer of USB1 port (default: 9100) - TCP Port 2: set TCP port for the printer of USB2 port (default: 9101) 5 Enable SMB (Server Message Block) Print/File Server: select or clear Enable SMB Print/File Server support. It is enabled in Factory Default. 5 Enable FTP Server: select or clear Enable FTP Server support. It is enabled in Factory Default and users may set some parameters as follows: - FTP Port: type an integer number to set FTP server’s TCP port (default: 21) - Set Maximum Session Number: select or clear Set Maximum Session Number support. You can limit the FTP session number by selecting the support and type an integer to set the allowable maximum session number. If you clear the support, it means that FTP server will have not any limitation in session number. - Set Passive Mode: select or clear Set Passive Mode support that FTP server can accept passive mode. - Enable FTP Authentication: select or clear Enable FTP Authentication support. If you select the support, you need to type user name and password to login to the server. If you clear the support, you enter the server as anonymous login. 5 Enable SANE (Scanner Access Now Easy) Server: select or clear Enable SANE Server support. It is enabled in Factory Default and users may set the

Page 50 of the LevelOne Print Server (FPS-3003) user manual — 8.2.3 Set up Server’s Configuration
Page 50 · click to enlarge
Page 50
TCP port as follows- SANE Port: set SANE server’s TCP port (default: 6566)
LevelOne Print Server (FPS-3003) — 8.2.3 Set up Server’s Configuration diagram (page 50)
Fig. 39 · 8.2.3 Set up Server’s Configuration
Page 51 of the LevelOne Print Server (FPS-3003) user manual — 8.2.3 Set up Server’s Configuration
Page 51 · click to enlarge
Page 51
„ User AccountsYou can change administrator name and

password or add a FTP account. If you forgot administrator name and password, you must to perform Restore Factory Default action by pressing Init button and plugging Power adaptor simultaneously. Please refer to Chapter 13 Restore Factory Default.

5 New Administrator: type your desired administrator name. 5 New Password: type your desired password. 5 Retype Password: confirm your previous password typing. Š User Accounts list

5 User name: Administrator can add a new FTP user account for accessing the storage attached to FPS-3003. 5 Password: After entering the user name and corresponding password, click “Add”. The account will take effect once shown in the blank below.

LevelOne Print Server (FPS-3003) — 8.2.3 Set up Server’s Configuration diagram (page 51)
Fig. 40 · 8.2.3 Set up Server’s Configuration

Š Set Administrator

Page 52 of the LevelOne Print Server (FPS-3003) user manual — 8.2.3 Set up Server’s Configuration
Page 52 · click to enlarge
Page 52
„ SNMPYou can set community and some parameters for

SNMP server. Furthermore, you can enable SNMP v3 for more security.

Š Set SNMP Configuration 5 Authentic Community: set Community name of SNMP server. 5 Trap Community: set Trap Community name for SNMP server to send trap packets. 5 Trap Address: type an IP address to send the Trap packet. 5 SysContact: type some letters for variable of SysContact that represents the name of system contact. 5 SysName: type some letters for variable of SysName that represents the name of system. 5 SysLocation: type some letters for variable of SysLocation that represents the location of system. 5 EnableAuthenTrap: type 1 or 2 for the variable of EnableAuthenTrap that represents to enable (1) or disable (2) to send Trap packets receiving the wrong Community name. Š SNMP V3 5 Enable SNMP V3: select or clear Enable SnmpV3 support 5 User Security name: set user security name of SNMP v3 5 Auth Password: set authentication password of SNMP v3. 5 Privacy Password: set privacy password of SNMP v3.

LevelOne Print Server (FPS-3003) — 8.2.3 Set up Server’s Configuration diagram (page 52)
Fig. 41 · 8.2.3 Set up Server’s Configuration
Page 53 of the LevelOne Print Server (FPS-3003) user manual — 8.2.3 Set up Server’s Configuration
Page 53 · click to enlarge
Page 53
„ EmailIf you want to receive some alerting mail from the

server, you have to enable SMTP Protocol, and set Email configuration. You can set new SMTP port number (default: 25). Š Set Email Configuration

5 SMTP Protocol: select or clear Enable SMTP support 5 SMTP Server Name: type your SMTP server’s host name or IP address. 5 SMTP Port Number: set new SMTP server’s TCP port number (default: 25). 5 Subject: type the subject of the e-mail. 5 From Address: type the sender’s e-mail address 5 To Address: type an e-mail address to send that mail to a person 5 Cc: stands for carbon copy; type an e-mail address to send that mail to a second person

LevelOne Print Server (FPS-3003) — 8.2.3 Set up Server’s Configuration diagram (page 53)
Fig. 42 · 8.2.3 Set up Server’s Configuration
Page 54 of the LevelOne Print Server (FPS-3003) user manual — 8.2.3 Set up Server’s Configuration
Page 54 · click to enlarge
Page 54
„ MaintenanceIf you want to restart server, restore factory

default values of the server, download new firmware file from product’s public web site and upgrade new firmware, you can use the Maintenance tool.

Š Restart Serverclick the button, the server will be
restarted. Š Factory Defaultclick the button, the server will restore

factory default values. Š Download New Firmware: click the button and you can

download new firmware or user software from product’s public web site. Š Upgrade New Firmware: click Open to find the system

firmware file to be upgraded. Click Upgrade to do the real firmware upgrading task.

LevelOne Print Server (FPS-3003) — 8.2.3 Set up Server’s Configuration diagram (page 54)
Fig. 43 · 8.2.3 Set up Server’s Configuration
Page 55 of the LevelOne Print Server (FPS-3003) user manual — Chapter 9 MFP Server’s Web Pages
Page 55 · click to enlarge
Page 55

Chapter 9 MFP Server’s Web Pages

9.1 Introduction FPS-3003 USB MFP server runs the daemon of http server, httpd on TCP port: 80. Users may use the web pages to see the server’s system status and configure the server. 9.2 Using Server’s Web Pages

9.2.1 Display Server Status

You can see the status of Host Information, TCP/IP and USB devices.

LevelOne Print Server (FPS-3003) — Chapter 9 MFP Server’s Web Pages diagram (page 55)
Fig. 44 · Chapter 9 MFP Server’s Web Pages
Page 56 of the LevelOne Print Server (FPS-3003) user manual — Chapter 9 MFP Server’s Web Pages
Page 56 · click to enlarge
Page 56

9.2.2 Set up Server Configuration

To set up the server configuration, the system will request user to enter administrator (default: admin) and password (default: admin) to login.

Š Set Host InformationYou have to set some

information for networking using SMB protocol: 5 Comment: optionally set to describe the server 5 Host Name: the name to represent the server for Windows networking using SMB protocol 5 Workgroup: the SMB workgroup name that the server belongs to. Š File Server Code Page: You have to select your code

page while operating network file sharing. Generally, the criteria of choosing code page are based on your Windows code page. For example, if your Windows code page is Traditional Chinese, you have to select Traditional Chinese (Big5) in server. Please refer to Chapter 6 File Server Function.

LevelOne Print Server (FPS-3003) — Chapter 9 MFP Server’s Web Pages diagram (page 56)
Fig. 45 · Chapter 9 MFP Server’s Web Pages

„ General Configuration

Page 57 of the LevelOne Print Server (FPS-3003) user manual — Š TCP/IP
Page 57 · click to enlarge
Page 57
„ USB Device InformationYou can set printer names and

display some information of USB mass storages and scanners. Please refer to Chapter 4, Chapter 6 and Chapter 7.

„ TCP/IPYou have to set the server’s TCP/IP configuration to

connect TCP/IP network. Please see Chapter 3 Basic Installation for more details.

„ Supported ProtocolsThe server supports the following

TCP/IP protocols:

Š TCP/IP

5 Enable LPR (Line Printer Remote) Printing: select or clear Enable LPR Printing support. It is enabled in Factory Default. 5 Enable IPP Printing: select or clear Enable IPP Printing support. It is enabled in Factory Default. 5 Enable Raw TCP Printing: select or clear Enable Raw TCP Printing support. It is enabled in Factory Default and users may set the protocol’s TCP ports as following boxes: - TCP Port 1: set TCP port for the printer of USB1 port (default: 9100) - TCP Port 2: set TCP port for the printer of USB2 port (default: 9101) 5 Enable SMB (Server Message Block) Print/File Server: select or clear Enable SMB Print/File Server support. It is enabled in Factory Default. 5 Enable FTP Server: select or clear Enable FTP Server support. It is enabled in Factory Default and users may set some parameters as follows: - FTP Port: type an integer number to set FTP server’s TCP port (default: 21) - Set Maximum Session Number: select or clear Set Maximum Session Number support. You can limit the FTP session number by selecting the support and type an integer to set the allowable maximum session number. If you clear the support, it means that FTP server will have not any limitation

Page 58 of the LevelOne Print Server (FPS-3003) user manual — Chapter 9 MFP Server’s Web Pages
Page 58 · click to enlarge
Page 58

in session number. - Set Passive Mode: select or clear Set Passive Mode support that FTP server can accept passive mode. - Enable FTP Authentication: select or clear Enable FTP Authentication support. If you select the support, you need to type user name and password to login to the server. If you clear the support, you enter the server as anonymous login. 5 Enable SANE (Scanner Access Now Easy) Server: select or clear Enable SANE Server support. It is enabled in Factory Default and users may set the TCP port as follows: - SANE Port: set SANE server’s TCP port (default: 6566)

„ User AccountsYou can change administrator name and

password or add a FTP user account. If you forgot administrator name and password, you must to perform Restore Factory Default action by pressing Init button and plugging Power adaptor simultaneously. Please refer to Chapter 13 Restore Factory Default.

5 New Administrator: type your desired administrator name. 5 New Password: type your desired password. 5 Retype Password: confirm your previous password typing. Š User Accounts list

5 User name: Administrator can add a new FTP user account for accessing the storage attached to FPS-3003. 5 Password: After entering the user name and corresponding password, click “Add”. The account will take effect once shown in the blank below.

Š Set Administrator

Page 59 of the LevelOne Print Server (FPS-3003) user manual — Chapter 9 MFP Server’s Web Pages
Page 59 · click to enlarge
Page 59
LevelOne Print Server (FPS-3003) — Chapter 9 MFP Server’s Web Pages diagram (page 59)
Fig. 46 · Chapter 9 MFP Server’s Web Pages
„ SNMPYou can set community and some parameters for

SNMP server. Furthermore, you can enable SNMP v3 for more security.

Š Set SNMP Configuration

5 Authentic Community: set Community name of SNMP server. 5 Trap Community: set Trap Community name for SNMP server to send trap packets. 5 Trap Address: type an IP address to send the Trap packet. 5 SysContact: type some letters for variable of SysContact that represents the name of system contact. 5 SysName: type some letters for variable of SysName that represents the name of system. 5 SysLocation: type some letters for variable of SysLocation that represents the location of system.

Page 60 of the LevelOne Print Server (FPS-3003) user manual — Chapter 9 MFP Server’s Web Pages
Page 60 · click to enlarge
Page 60

5 EnableAuthenTrap: type 1 or 2 for the variable of EnableAuthenTrap that represents to enable (1) or disable (2) to send Trap packets receiving the wrong Community name. Š SNMP V3

5 Enable SNMP V3: select or clear Enable SnmpV3 support 5 User Security name: set user security name of SNMP v3 5 Auth Password: set authentication password of SNMP v3. 5 Privacy Password: set privacy password of SNMP v3.

LevelOne Print Server (FPS-3003) — Chapter 9 MFP Server’s Web Pages diagram (page 60)
Fig. 47 · Chapter 9 MFP Server’s Web Pages

„ Restart Server: click the button, the server will be restarted.

Page 61 of the LevelOne Print Server (FPS-3003) user manual — Chapter 9 MFP Server’s Web Pages
Page 61 · click to enlarge
Page 61
LevelOne Print Server (FPS-3003) — Chapter 9 MFP Server’s Web Pages diagram (page 61)
Fig. 48 · Chapter 9 MFP Server’s Web Pages

„ Maintenance If you want to restore factory default values of

the server and upgrade new firmware, you can use the Maintenance tool.

5 Factory Default: click the button, the server will restore factory default values. 5 Download New Firmware from Web Site: click the button and you can download new firmware or user software from product’s public web site. 5 Upgrade New Firmware: click Open to find the system firmware file to be upgraded. Click Upgrade to do the real firmware upgrading task.

LevelOne Print Server (FPS-3003) — Chapter 9 MFP Server’s Web Pages diagram (page 61)
Fig. 49 · Chapter 9 MFP Server’s Web Pages
Page 62 of the LevelOne Print Server (FPS-3003) user manual — Chapter 11 SNMP
Page 62 · click to enlarge
Page 62

Chapter 10 Email Alerting

FPS-3003 USB MFP server can send some email messages to the user while the following events occurs

1. Add/Remove USB device: When add new USB device or remove current USB device, the server will send the mail to notify the user. 2. System Error: When there are some errors occur in the server, the server will send the mail to notify the user.

Chapter 11 SNMP

FPS-3003 USB MFP server runs the daemon of SNMP server that supports the SNMP v1, v2c and v3 protocols (Simple Network Management Protocol). Users can use SNMP client software as actual management tool such as HP Openview to management your MFP server. The FPS-3003 MFP servers support all relevant parts of MIB-II and a private FPS-3003 MFP server MIB. You can set value of some MIB variables from the server’s web pages or LevelOne MFP Control Center Tool.

Page 63 of the LevelOne Print Server (FPS-3003) user manual — USB2
Page 63 · click to enlarge
Page 63

Chapter 12 Troubleshooting

This chapter provides useful information to help you resolve difficulties you may experience with your FPS-3003 USB MFP server. Fault symptoms, possible causes and remedial actions are provided within a quick reference table. General USB ports in FPS-3003 USB MFP server only support USB printers, USB Mass storages and USB scanner of HP Office Jet Series.

12.1 LED Indicators

Orange Power On Power

Not lit Power off/System error

Green Network connected Link

Not Lit No physical connection to network

Green blinking Activity on network Status

Not lit No activity on network

USB1

Green USB device connected

Green blinking Connected USB device error

Not lit No physical connection to USB device

USB2

Green USB device connected

Green blinking Connected USB device error

Not lit No physical connection to USB device USB Device Status

Ready Printer is ready. Printer

Printing Printer is printing.

Indicators Color/Behavior Description · Devices Status Description

Page 64 of the LevelOne Print Server (FPS-3003) user manual — Chapter 12 Troubleshooting
Page 64 · click to enlarge
Page 64

Out of paper Printer is out of paper.

Error There are errors in network printing.

Ready Storage is ready. Mass Storage Error There are errors in network File server.

Ready Scanner is ready.

Flatbed Scanning Flatbed of scanner is scanning.

Scrollfed of scanner is scanning.

Error There are errors in network scanning.

Scanner · Scrollfed Scanning

Page 65 of the LevelOne Print Server (FPS-3003) user manual — 13.1 Using Server’s Web Pages
Page 65 · click to enlarge
Page 65

Chapter13 Restore Factory Default

This chapter describes how to restore default parameters of the MFP server. The server provides the following methods to achieve restoring default parameters of the MFP server.

13.1 Using Server’s Web Pages

1. Go to the server’s web page and click Maintenance 2. Login your administrator (default: admin ) and password (default: admin ). 3. Click Factory Default .
4. Click Yes to confirm your action
LevelOne Print Server (FPS-3003) — 13.1 Using Server’s Web Pages diagram (page 65)
Fig. 50 · 13.1 Using Server’s Web Pages
Page 66 of the LevelOne Print Server (FPS-3003) user manual — 13.2 Using LevelOne MFP Control Center
Page 66 · click to enlarge
Page 66

13.2 Using LevelOne MFP Control Center

1. Start LevelOne MFP Control Center and Auto-searching MFP server window will appear. 2. If the tool finds MFP servers in your local area network, then you have to select a MFP server from the server list. 3. Double click the highlight list and type the server’s administrator (default: admin ) and password (default: admin ). 4. After you login successfully, from the Server menu, select Maintenance . The Maintenance dialog appears. 5. Click Factory Default.

13.3 Using Init Button Simultaneously press Init button and power on (plug the power adaptor line) the server until LED indicators of Power, USB1 and USB2 blink. After that, the servers will operate using the Factory Default values after next restarts.

Page 67 of the LevelOne Print Server (FPS-3003) user manual — 13.4 Default Parameters List Host Information
Page 67 · click to enlarge
Page 67

13.4 Default Parameters List Host Information

„ Comment (Optional)FPS-3003 USB MFP Server
„ Host NameFPS-3003
„ WorkgroupLevelOne

„ Code Page of File Server: Western European

„ Product IDFPS-3003 xxxx, where xxxx represents the last 4

bytes of Ethernet address. TCP/IP

„ Automatically get IP using DHCP

„ Default IP192.168.1.100
„ Default Subnet Mask255.255.255.0 Protocols

„ Enable SMB Print/File Server

„ Enable IPP Printing

„ Enable LPR Printing

DeviceFPS-3003 Port Name:
- USB1_LPR (queue nameUSB1_LQ) - USB2_LPR (queue name: USB2_LQ)

„ Enable Raw TCP Printing Device: FPS-3003

Port Name:

- USB1_RAWTCP port 9100 - UBB2_RAW: TCP port 9101

„ Enable SANE Server

SANE Port6566
FTP Port21 Passive Mode: Disabled Set Maximum Session Number: Disabled FTP Authentication: Disabled SNMP
„ Authentic Communitypublic
„ Trap Communitypublic

„ FTP Server

Page 68 of the LevelOne Print Server (FPS-3003) user manual — 13.4 Default Parameters List Host Information
Page 68 · click to enlarge
Page 68
„ SysContactsales@ LevelOne.com
„ SysNameFPS-3003 USB MFP Server
„ SysLocationwww.LevelOne.com
„ EnableAuthenTrap2 (disable) User Account

„ Administrator:admin

„ Passwordadmin
Page 69 of the LevelOne Print Server (FPS-3003) user manual — Procedure B: Using Server’s Web Pages
Page 69 · click to enlarge
Page 69

Chapter14 Upgrade New Firmware

This chapter describes how to upgrade your new firmware. You can use the following Procedures to upgrade new firmware

Procedure A: Using PC User Software

1. Open the FPS-3003 MFP Control Center. It will automatically search the existing servers and display their status. 2. Select the server that you want to upgrade the firmware. Double click the selected server and enter Administrator Name and Password. Please note that the default values of Administrator and Password are admin. 3. Select the Maintenance button.
4. Click Open your new firmware file and click Upgrade . 5. Wait about 15 seconds for system reboot.

Procedure B: Using Server’s Web Pages

1. Power on FPS-3003. Suppose FPS-3003 is in DHCP mode. 2. Check FPS-3003's IP address. 3. First, run FPS-3003 control center. The control center will
Page 70 of the LevelOne Print Server (FPS-3003) user manual — Procedure C: Using Init Button and TFTP Client
Page 70 · click to enlarge
Page 70

automatically search FPS-3003 on the LAN. Then FPS-3003's IP address will be shown in control center. 4. Run any web browser, like Microsoft Internet Explorer. Go to http://a.b.c.d to access FPS-3003's home page, where a.b.c.d is FPS-3003's IP address. 5. Click "Maintenance" at the left side menu.

6. Login FPS-3003 with administrator "admin" and password "admin". 7. Click "Upgrade Firmware". 8. Click "Browse" button to choose the file of new FPS-3003 firmware. 9. Click "Upload" button to start firmware upgrade. 10. Wait about 15 seconds for system reboot.

Procedure C: Using Init Button and TFTP Client

1. Simultaneously press Init button and power on (plug the power adaptor line) the server until LED indicators of Power, USB1 and USB2 blink. After that, the servers will operate using the factory default values after next restarts. 2. Start the TFTP client Tool which contains in the CD-Rom: Image Burner 3. Type the server’s Fallback IP address: 192.168.1.100 and click Open Image to open your new firmware. 4. Click Upload Image
Page 71 of the LevelOne Print Server (FPS-3003) user manual — Chapter15 Init Button
Page 71 · click to enlarge
Page 71

Chapter15 Init Button

The Init button is used for:

1. Print Configuration Report: Press Init button for exceeding 3 seconds and then the connected HP printer or PCL supported printer will print out the system configuration.
LevelOne Print Server (FPS-3003) — Chapter15 Init Button diagram (page 71)
Fig. 51 · Chapter15 Init Button
2. Maintenance : Simultaneously press Init button and turn on (plug the power adaptor line) the server until USB1 and USB2 LED indicators simultaneously blink. After that, the server will do the following tasks: A. Perform a Factory Default of the MFP server, which will

restore most of the parameters and settings to factory default values,

Page 72 of the LevelOne Print Server (FPS-3003) user manual — Chapter16 Technical Specifications
Page 72 · click to enlarge
Page 72

B. Perform a TFTP server. You can upgrade new firmware

using any TFTP client tool.

Chapter16 Technical Specifications

Support for printers and MFPs from

Firmware upgrade using the internal

Brother, Canon, Epson, HP, IBM, Kyocera,

web pages, Windows Tool, and TFTP

Lexmark, Minolta, NEC, Oce, OKI, Ricoh,

Sharp, Star, TEC, Toshiba, Zebra, Xerox,

etc.

y LAN10/100 Mbps Ethernet

Please note that the server do not

support GDI printers.

y 2 USB 1.1/2.0 Low and Full speed.

Support for scanners of MFPs from HP

office jet and some recommended

scanners.

y 2 USB 1.1/2.0 Full-speed host

Print Server Supported Systems

y Ethernet 10/100 Mbps

y Microsoft Windows98, Me, 2000, XP,

y ARM9-based RISC microprocessor,

y Memory2 MB Flash, 8 MB RAM

File Server Supported Systems

y Microsoft Windows98, Me, 2000, XP,
y 5 LED indicatorsPower, Link,

Status, USB1 and USB2

y Init button to perform factory

default, upgrade firmware, and

File Server Supported Code Pages

y Western Europe and United States

y Power provided by external supply

(5V 2A).

y Japanese (Shift JIS)

y Maximum consumption 10W

y Traditional Chinese (Big 5)

y Simplified Chinese (GB 2312)

y Height 2.6 cm

y Width7.6 cm
Show 22 more labels / short text on this page
Supported Printers · Firmware Upgrade · Network Connection · MFP Connection · Supported Scanners · y Bi-directional support · Hardware · ports · and 2003 · operating at 166MHz · y Unix/Linux · Front Panel · and 2003 · y Unix/Linux · print configuration · Power Consumption · y Central Europe · y Greek · y Cyrillic · y Korean · Dimensions · y Thai
Page 73 of the LevelOne Print Server (FPS-3003) user manual — - EN 60950
Page 73 · click to enlarge
Page 73
y Depth10.4 cm

Scan Server Supported Systems

y Weight125 g
y Microsoft Windows98, 2000, XP and
y Temperature40-105 °F (5-40 °C)

y Humidity 0 – 70%

- DHCP, FTP, HTTP, SNMP v1/v2c/v3

y EMC:

- EN 55022/1998 - EN 55024:1998 - EN 61000-3-2 - EN 61000-3-3 - FCC part 15 Subpart B,

- TCP/IPLPR, Raw TCP,

NetBIOS over TCP/IP (SMB), IPP,

- SMBNetBIOS over TCP/IP - FTP

y Safety:

- EN 60950

Any standard web browser (Netscape

y Quick Installation Guide

6.x or higher and MS Internet Explorer

5.x or higher).

y Internal web pages for configuration,

monitoring and firmware upgrading

y Windows tool for installation,

Show 17 more labels / short text on this page
y Arabic · Environmental · Supported Protocols · Approvals · y General · y Print Server · y File Server · Class A · y Scan Server · - SANE Server · Supported Web Browsers · Included Accessories · y Power supply · y Installation CD · MFP Server Management · configuration, monitoring and · firmware upgrading
Page 74 of the LevelOne Print Server (FPS-3003) user manual — 17.1 Compatibility List
Page 74 · click to enlarge
Page 74

Chapter17 Appendix

17.1 Compatibility List

„ FPS-3003 USB MFP server should support most USB printers

(except Host-based/GDI printers), and USB disks or USB memory cards.

„ FPS-3003 USB MFP server should support the scanners of HP

Office Inkjet Series all-in-one printers (MFP). The supported MFPs are list below.

4100 series, 4200 series, 5500 series, 6100 series, 7100 series, 9100 series, PSC 1200 series, PSC 1300series, PSC 2400 series, PSC 2500 series

HP LaserJet 1220, HP LaserJet 3200, HP LaserJet 3200se, HP LaserJet 3200m, HP LaserJet 3300, HP LaserJet 3310, HP LaserJet 3320, HP LaserJet 3330

„ FPS-3003 USB MFP server should support the following printers

to print configuration report using Init button

1100 series, 2300 series, 2600 series, 3000 series

3600 series, 5100 series, 5550 series, 5600series, 5850 series, 6122 series, 6127 series, 9300 series, 9600 series, 995c series, cp1700 series

Office jet 4100 series, 4200 series, 5500 series, 6100 series, 7100 series, 9100 series, PSC 1200 series, PSC 1300series, PSC 2400 series, PSC 2500 series

Photo smart 140 series, 240 series, 7200 series, 7600

Show 7 more labels / short text on this page
Model MFP Series · HP Office jet · HP LaserJet all-in-ones · Others · Model Printer · Business Inkjet · Desk jet
Page 75 of the LevelOne Print Server (FPS-3003) user manual — Chapter17 Appendix
Page 75 · click to enlarge
Page 75

series, 7700 series, 7900 series

Laser Printer most PCL black & white and color printers

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the LevelOne Print Server (FPS-3003)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LevelOne Print Server (FPS-3003)

Be the first to ask — other owners or our team will answer.

Original document

LevelOne Print Server (FPS-3003) manual PDF

75 pages·4 MB·Server·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…