
Servers
EPS-3001TU FPS-3001TXU FPS-2111TXU FPS-2101TXU FPS-2101USB FPS-2013TXU FPS-2003TXU
User Guide
Copyright 2002. ALL RIGHTS RESERVED.
All trademark and trade names are the properties of their respective owners.



This chapter provides details of your LevelOne Printer Server's features and components.
Congratulations on the purchase of your new LevelOne Printer Server. This device was designed to provide a simple and efficient network printing solution.
¾ Versatility. The LevelOne Printer Server supports up to five protocols: NetWare,
TCP/IP, SMB (Service Message Block), AppleTalk (EtherTalk), and NetBEUI. Most models feature an auto-sensing 10/100BaseT Ethernet interface port. Operating system support includes Unix, Novell, and Microsoft Windows.
¾ Easy Installation. The LevelOne Printer Server makes adding printers or plotters to
your network simple. The auto-sensing feature on the LAN interface means that there is no need to set jumpers or perform software configuration to select the network speed or duplex setting.
¾ Easy Setup. A number of utility programs are supplied to simplify setup. For
Windows 95/98/NT users, the BiAdmin program makes it easy to configure the LevelOne Printer Server for a variety of network and server configurations.
¾ Web-based interface. On models supporting 100BaseT, the LevelOne Printer Server
incorporates a Web-based interface to provide an easy method of configuration in TCP/IP networks. When using this method, no software needs to be installed.
¾ Compact Size. This allows the LevelOne Printer Server to be used even where space
is limited.
¾ Remote Management Tools. A variety of software tools are provided. In most
environments, both the LevelOne Printer Server and attached bi-directional printers can be configured remotely.
¾ SNMP Support. The LevelOne Printer Server can act as a SNMP agent, with it own
MIB. This allows TCP/IP users to monitor, configure and troubleshoot the LevelOne Printer Server using their existing SNMP management tools.
¾ JetAdmin Support. 100BaseT models support HP's JetAdmin utility. If you are
already using this program, you can also use it to manage your LevelOne Printer Server.
¾ Internet Printing. Using TCP/IP, the LevelOne Printer Server can be configured to
allow clients, suppliers, colleagues and others to print to one of your printers from anywhere on the Internet.
The LevelOne Printer Server does not store the date, nor does it perform date calculations. When necessary, it obtains the current date from the network or client operating system. We recommend the use of network and client operating systems which are year 2000 compliant.

For your own safety, and to protect your LevelOne Printer Server, please observe the following safety advice.

You should find the following items packaged with your LevelOne Printer Server. If any items are missing, contact your dealer immediately.
Introduction

This section contains details of all LevelOne Printer Server models covered by this manual. Please take a few minutes to familiarize yourself with your new LevelOne Printer Server.
1 Male Parallel Port, for direct connection to the printer.
2 Orange Error LED. See page 11 for details.
3 Green Status LED. See page 11 for details.
4 9V Power port
5 10BaseT Connector.
Item Description









1 Male Parallel Port, for direct connection to the printer.
2 Orange Error LED. See page 11 for details.
3 Green Status LED. See page 11 for details.
4 5V Power port
5 10/100BaseT Connector.
The FPS-2111TXU offers support for both 10BaseT and 100BaseT environments. It features one UTP connector and one bi-directional parallel port.
Introduction · Item Description


2 Red Error LED. See page 11 for details.
3 Green Link LED See page 11 for details.
4 12V Power port
5 10/100BaseT Switches See page 11 for details.
6 10/100BaseT STP Connector
7 10/100BaseT Link LED
Figure 3 FPS-2111TXU · Item Description · 1 Parallel Port

2 Green Link LED. See page 11 for details.
3 Red Error LED. See page 11 for details.
4 12V Power port
5 Diagnostic push button. See page 12 for details.
6 DIP Switches. See page 11 for details.
9 10Base2 connector.


1 Parallel Port 1
2 Parallel Port 2
3 Parallel Port 3
4 Red Error LED. See page 11 for details.
5 Green Link LED. See page 11 for details.
6 Reset Button. This will Reboot the LevelOne Printer Server.
7 10/100BaseT Switches. See page 11 for details.
8 10/100BaseT Link LED
10 12V Power port
Item Description · 9 10/100BaseT Connector

1 Parallel Port 1
2 Parallel Port 2
3 Parallel Port 3
4 Green Link LED. See page 11 for details.
5 Red Error LED. See page 11 for details.
6 Diagnostic push button. See page 12 for details.
7 DIP Switches. See page 11 for details.
8 100BaseT Link LED - lights if using 100BaseT.
9 10BaseT Link LED - lights if using 10BaseT.
10 10Base2 connector.
12 12V Power Port
Introduction · Item Description · 11 10/100BaseT Connector

4 5 6 7


2 ACT LED
3 LAN LED
6 Reset Button. This will Reboot the LevelOne Printer Server.
7 12V Power Port
Item Description · 4 USB Connector · 5 10/100BaseT Connector

All LevelOne Printer Servers are fitted with 2 LED indicators. The red LED is the Status/Error indicator. The green LED is the Power/Link indicator. The LED indicator modes are described in the following table.

On Flashing (USB only) No printer connected to the USB port.
Flashing Off Normal operation - transmitting or receiving packets from the network.
The DIP switches are used to set the LAN connection. Operation is as follows.

The other possibilities are reserved, and should not be used.
The DIP switches are used to set the LAN connection. Operation is as follows.

UP - - Auto select LAN connection (Default) Switches 2 and 3 have no effect.
The other possibilities are reserved, and should not be used.
Introduction

Models FPS-2101TXU and FPS-2003TXU are fitted with a "Diagnostic Push Button".
This button is used to restore the factory default settings, or to print a test page. The test page will contain all the current settings, and will be output to the printer attached to port 1.

This chapter describes how to install the LevelOne Printer Server in your Local Area Network.
During configuration you will be able to change the device name. The new name MUST NOT contain any spaces or blanks
Connect the printer or plotter to the LevelOne Printer Server's printer port(s), as appropriate:
Leave the LevelOne Printer Server powered OFF while connecting it to the Printer(s) and the LAN.

Use only the Power Supply unit provided with the LevelOne Printer Server.

This chapter provides an overview of the configuration process.
The LevelOne Printer Server is designed to support many different platforms, and the configuration required will depend upon the environment in which it is installed. Depending upon the situation, any of the following may require configuration:
For each supported platform, detailed instructions are contained in the appropriate chapter in this document.
Many different methods and utilities can be used to configure the LevelOne Printer Server.
The recommended method for configuring the LevelOne Printer Server is to use the supplied BiAdmin utility program. If using NetWare, this program can be used to configure the NetWare Server as well as the LevelOne Printer Server. For details about installing and using BiAdmin, refer to Chapter 4 - BiAdmin Utility Program. BiAdmin requires Window 95/98 or Windows NT4.0 or later.
Most Browsers will work with the Web-based interface, provided on all models supporting 100BaseT. See Chapter 7 - TCP/IP for details.
The methods listed below can also be used. For more details, refer to the full user manual supplied on the CD-ROM.
FTP All TCP/IP networks Using this method, the configuration file is down loaded from the LevelOne Printer Server, edited, then sent back.
Windows 95/98/NT 100BaseT models support this program.
Menu-based DOS program for NetWare users.
Telnet All TCP/IP networks Telnet can be used only to monitor the printers attached to the LevelOne Printer Server.
Method Platform Details · JetAdmin (HP) · PSConfig DOS (IPX/SPX)

WebAdmin Windows NT Server (TCP/IP) Web Browser
WebAdmin is installed on the NT Server, and then accessed using a Web Browser.
WPConfig Windows 3.1 (IPX/SPX)
Not all LevelOne Printer Server features are available.

This chapter covers the installation and operation of the BiAdmin utility.
This program requires:
Additional Recommendations:

Start the program by using the icon created by the setup program.
When run, the program searches the network for all active LevelOne Printer Servers, then lists them on screen, as shown by the example screen below.


On the left side of the screen is a column for Groups. Each LevelOne Printer Server may be placed in a group, using the Configuration-System Configuration-Groups menu option.

On the right side of the screen is a list of all LevelOne Printer Servers found on the network. For each device, the following data is shown:
BiAdmin Utility Program

Once a LevelOne Printer Server has been selected, the Icons become active.
The icons provide status information as well as access to the selected LevelOne Printer Server settings. If an icon is grayed out, that option or protocol is unavailable.
All of the settings for the current device are displayed in a read-only scrollable list in the left panel.
You can use the "Save to File" and "Restore to Device" buttons on this screen to save a copy of the selected device's CONFIG file to your PC, or restore a previously saved file to the selected LevelOne Printer Server.
After selecting this icon, a Detail button will be available to show more information about the printer.
The following icons are available. Refer to the on-line help for details of the data on each screen.
BiAdmin supports configuration of both the LevelOne Printer Server and Novell NetWare servers.

allows you to configure both the LevelOne Printer Server and the NetWare server from within BiAdmin.
See Chapter 6 for more details on using BiAdmin with NetWare Servers.
Selecting this icon will allow configuration for TCP/IP. Some models may have checkboxes for DHCP, Bootp, and Rarp. Some models may also display the setup data for the proprietary "Internet Printing" feature (printing via E- Mail).
See Chapter 5 for more details.
Configuration is only required if using Simple Network Management Protocol. See Chapter 11 for more details.
Logical Port Configuration Menu equivalent: Configuration - Logical Port
Logical port (printers) can be used in the NetWare and Unix environments.
Upgrade Menu Equivalent: InitDevice - Upgrade This option allows you to upgrade the firmware for the selected LevelOne Printer Server. Before using this option, you need to obtain the .BIN file for the firmware upgrade, and copy it to the same directory as BiAdmin.
Refresh Menu Equivalent: None Select this icon to update the LevelOne Printer Server device listing after changing the name or IP Address.
Exit the BiAdmin program. This does not save any changes you have made; you must Save to Device on each screen.
BiAdmin Utility Program

Device Info Same as Device button.
Display all the configuration and status information about the selected LevelOne Printer Server. The data is presented in a scrolling, read-only window.
Port Same as Port Status buttons.
Attach Remote This is used to connect to a LevelOne Printer Server device on another LAN segment. If your LAN does not have a Router, ignore this option.
This option allows you to designate which LAN protocol will be used for communication between the selected device and this application. You should select ONE protocol only.
Find Use this option to use the IPX/SPX protocol to locate a LevelOne Printer Server on the LAN. Simply enter the Default Name of the LevelOne Printer Server you wish to locate. The Default Server Name is shown on a sticker on the base of the device.
Reset Device This will cause the device to reboot. This should be done after making any configuration changes, or if the device stops responding after some problems.
This will restore ALL device values to their factory defaults. To restore only the current screen, use the Set to Default button on the screen.
Set IP Address For TCP/IP networks only:
Upgrade Upgrade the firmware in a LevelOne Printer Server. See Upgrade Icon for details.
Connected Protocol · Restore Factory Default

The System option allows you to:
The Configuration Menu also contains selections for each of the following. These have the same effect as the corresponding Icon:
Print Test Page Use this option to print a test sheet from the selected LevelOne Printer Server port. The test print out will include status information.
This menu option refers to print jobs which has been received through the proprietary "Internet Printing" feature (printing via E-Mail). This menu option can be used to terminate a print job which is not printing correctly.
Abort Mail Print Job
The "Abort Mail Print Job" menu option can NOT be used to cancel IPP (Internet Printing Protocol) print jobs.
BiAdmin Utility Program

This chapter details using the LevelOne Printer Server in the AppleTalk environment.
The LevelOne Printer Server supports AppleTalk (EtherTalk), PAP, ATP, NBP, ZIP and DDP protocols, enabling Macintosh computers on the network to view and use the LevelOne Printer Server as a regular AppleTalk printer. Configuring and printing in the EtherTalk environment operates completely as usual.
The PSTool program has been provided specifically for the Macintosh environment, to allow easy configuration of your LevelOne Printer Server. However, it is not necessary to install and use this program for basic operation.
System 7.x OS or newer.
Printing with the LevelOne Printer Server installed in an AppleTalk network is identical to normal printing.
For example, select a document that you want to print and then select File - Print. Chose the desired printer.

This section describes the configuration changes which can be made to your LevelOne Printer Server device.
Windows Software
In a mixed Windows PC/Macintosh environment, you can use the BiAdmin utility program to configure the LevelOne Printer Server. For details on installing and using BiAdmin, refer to Chapter 4 - BiAdmin.
In AppleTalk, you can use SimpleText to edit the LevelOne Printer Server’s CONFIG file and the supplied PSTool program to send it to the LevelOne Printer Server. The procedure is as follows:
PSTool CONFIG file (e.g. config.3p)
begin CMD 0001 Device Name: xxxxxxxx 3000 Apple Zone : * 3001 Printer Type (P1): LaserWriter 3002 Printer Type (P2) LaserWriter 3004 Printer Type (P3) LaserWriter 3101 AP_PCOMM1: No 3102 AP_PCOMM2: No 3104 AP_PCOMM4: No 9002
The appropriate values for each line are described in the following section.
Do NOT modify the following lines: begin CMD 9002:
AppleTalk

When editing the CONFIG file, only the parameter should be changed. The parameter is the last part of the line, after the colon (:). Ensure that you use only valid parameters.
The Device Name will initially be the Default Server Name. The Default Server Name is shown on a sticker on the base of the device. The Device Name can be changed, but the new name MUST NOT exceed 19 characters in length.
The default value “*” allows all AppleTalk zones to access the LevelOne Printer Server’s printers. To restrict access to a particular zone, enter the zone name here.
These are text fields, used to describe the printer driver used for each port. P1, P2, P3 refer to parallel ports 1 to 3 respectively. The name can be up to 19 characters long.
These settings determine whether the port uses ASCII or Binary Communication Protocol. Enter NO for ASCII or YES for Binary. The lines refer to the following ports.
In choosing which Protocol to use, consider the following points.

This chapter describes using your LevelOne Printer Server in the NetWare environment.
This section describes how the LevelOne Printer Server functions in the Novell NetWare environment.
The LevelOne Printer Server fully supports both Bindery and NDS Novell systems, and be configured as either a NetWare Printer Server or NetWare Remote Printer.
Novell Distributed Printing Services (NDPS) using TCP/IP under NetWare 5 is also supported. See page 44 for details.
Logical Printers can be used to create a “Virtual” printer. Single port models support 3 logical printers, while multi-port models support 8 logical printers.
The Logical Printers are named L1, L2, and L3; or L1 to L8 on multi-port models. The names can not be changed.
PCONSOLE or NWAdmin must be used to create new (logical) printers and assign print queues to the printers. When creating logical printers, NetWare Printer 8 corresponds to Logical printer L1 on the LevelOne Printer Server, printer 9 to Logical printer L2, and so on up to printer 15 (logical printer L8).
The LevelOne Printer Server requires the following data, if logical printers are going to be used.
Physical Port Select the parallel port (P1 to P3) for this Logical Printer
The printer control string (in Hex) to be sent to the printer before each print job.
String After Job The printer control string (in Hex) to be sent to the printer after each print job.
Convert LF to CR+LF
If ON, LF (line feed) characters are changed to CR+LF (carriage return + line feed). If OFF, no conversion is done.
String Before Job

To support the widest possible range of users , the LevelOne Printer Server is supplied with the utilities listed in the following table.
BiAdmin If possible, you should use the supplied BiAdmin utility for configuration. BiAdmin is a powerful, user-friendly program which runs under Windows 95/98/NT.
See Chapter 4 - BiAdmin Utility for details on installing this program, and general instructions on usage.
BiAdmin works best if you have Novell NetWare Client 32 for Windows installed.
Quickset QUICKSET is a DOS-based command-line program. It will configure the LevelOne Printer Server and the current Novell server in a single operation. However, it provides few options.
PSConfig PSConfig is a DOS-based, menu-driven program. It uses the IPX/SPX protocol to connect to the LevelOne Printer Server, so your PC must load the IPX/SPX drivers before PSConfig can be used.
PSConfig can only configure the LevelOne Printer Server itself. You must use the NetWare’s PCONSOLE or NWAdmin to configure the NetWare server.

With NetWare Client 32 installed on your PC, BiAdmin’s NetWare capabilities are enhanced. As well as configuring the LevelOne Printer Server, you can configure the NetWare Server or Servers.

NetWare

If Bindery Print Server Mode is selected, the following screen will appear:

Print Server Name Change the name of the selected LevelOne Printer Server if you wish. (This field is also on the Configuration-System menu.)
Master File Server Name of the LevelOne Printer Server’s master file server (NetWare server). Select from the drop-down list.
Defines how often the LevelOne Printer Server will poll the queues to be serviced. The default is 1 second.
Job Notification by Connection ID
Set to Yes to receive a job notification at only the workstation where the print job originated, No to receive a job notification at all workstations that you have logged on.
Quickset This option will configure the NetWare server using default values. See below for details.
Use this to configure the NetWare server. See below for details. See the following section for details
Help View context-sensitive help.
Set to Default Replace the on-screen values with the default values. These are NOT saved until you click Save to Device. (No changes are made to the NetWare server.)
Save to Device Save any changes you have made to the LevelOne Printer Server
Cancel Ignore any changes made since the last Save operation; close the window.

The Quickset button on the previous screen will configure the NetWare server using default values derived from the default name, as shown on the following example.

This screen displays the name the selected LevelOne Printer Server, and the following information for each port:
Printer - the NetWare printer object which will be created on the current server.
Queue - the NetWare queue associated with the Printer Object. This queue will be serviced by the current LevelOne Printer Server, with print jobs being sent to the port shown. Change the default values if you wish, then click Setup to create these objects on the NetWare server.
Clicking the NetWare Configuration button will reveal one of the following screens, depending on the number of servers:

NetWare

Clicking the NetWare Configuration button will reveal the following screen:

File Server This drop-down list will be operational only if you have assigned more than 1 file server to be serviced by the LevelOne Printer Server.
Printer Create Printer Objects, assign Print Queues, and assign users to Print Queues (Required). See the following section for details.
Operator Assign Operators to the NetWare Print Server object. (Optional) These operators will then have permission to manage the NetWare Print Server object. The screen is identical to Figure 18: Assign Operator to Queue (Bindery).
User Assign Users to the NetWare Print Server object. (Optional) These users will then be able to view the status of the NetWare Print Server object. The screen is identical to Figure 17: Assign Users to Queue (Bindery).
Password Change the login password used by the LevelOne Printer Server when it connects to the NetWare server. By default, there is no password. See Password for details.


NetWare

This screen will be displayed when a port button is clicked on the previous screen.
Use this screen to assign queue(s) to the printer object associated with the selected port.

This screen displays the name of the NetWare Printer on the top of the screen.
Queues serviced by this NetWare printer are listed on the left, and other queues on the right.

Select the queue, then click Users on the screen above to see the following screen. The current queue name is shown on the top of the screen.

Select Operators from Figure 16: Assign Queues to view the following screen.

NetWare

Clicking the Password button on the screen shown in Figure 14: Configure NetWare Server (Bindery PS mode), allows you to simultaneously change the NetWare password for the Master File Server, and the NetWare login password stored in the LevelOne Printer Server. (The LevelOne Printer Server must be able to login to the NetWare server.)
You will see a screen like the example below.


If Print Server - NDS Mode was chosen, the following screen will appear.

Change the name of the selected LevelOne Printer Server if you wish. (This field is also on the Configuration-System menu.)
NDS Tree Name Select the File Server's NDS tree name (root name)
Print Server NDS Context
Select Browse to view the NDS tree and select the appropriate Context.
Defines how often the LevelOne Printer Server will poll the queues to be serviced.
Job Notification by Connection ID
Set to Yes to receive a job notification at only the workstation where the print job originated, No to receive a job notification at all workstations that you have logged on.
Use this to configure the NetWare server. See the following section for details.
Quickset This option will configure the NetWare server using default values. See below for details.
Help View context-sensitive help.
Set to Default Replace the on-screen values with the default values. These are NOT saved until you click Save to Device. (No changes are made to the NetWare server.)
Save to Device Save any changes you have made to the LevelOne Printer Server
Cancel Ignore any changes made since the last Save operation; close the window.

The Quickset button on the screen above will configure the NetWare server with default values based on the default name of the LevelOne Printer Server.
You will see a screen like the following example.

Change the default values if you wish, then click Setup to create these objects on the NetWare server.
The configuration data will be saved to the NetWare server and the LevelOne Printer Server.
Clicking this button will reveal the following screen.

The NetWare Print Server name is shown at the top of the screen.
The options available are:



This screen displays the current NetWare Printer Object at the top of the screen.
Queues serviced by the current Printer Object are listed on the left, and other queues (in the current context) on the right.
NetWare

Select on queue on the screen above, then click Users to see the following screen.

The screen allows you to assign users to the current queue. The current queue is displayed on the top of the screen.
To assign Operators to the selected queue, select Operators from Figure 24: Assign Queues (NDS PS mode). This step is optional; operator assignment has no effect on operation of the LevelOne Printer Server.


The current Queue and Context are displayed at the top of the screen.
Clicking the Password button on the screen shown in Figure 22: NetWare Configuration (NDS PS mode)allows you to simultaneously change the NetWare password for the Master File Server, and the NetWare login password stored in the LevelOne Printer Server. (The LevelOne Printer Server must be able to login to the NetWare server.)
You will see a screen like the example below.
NetWare

If, on the original screen, Remote Printer Mode - Bindery, was selected, the following screen will be shown.

Device Name Change the name of the selected LevelOne Printer Server if you wish. (This field is also on the Configuration-System menu.)
File Server Select the NetWare File Server to service each port.
Novell Printer Server for P1 (Parallel port 1)
Select the NetWare print server to service the LevelOne Printer Server's parallel port 1.
Novell Printer Server for P2, P3
Select the NetWare print server to service the LevelOne Printer Server's parallel port 2 (P2), parallel port 3 (P3).
Set to Default Replace the on-screen values with the default values. These are NOT saved until you click Save to Device. (No changes are made to the NetWare server.)
Save to Device Save any changes you have made to the LevelOne Printer Server
Cancel Ignore any changes made since the last Save operation; close the window.
Help View context-sensitive help.
Data · Buttons

If, on the original screen, Remote Printer Mode - NDS was selected, the following screen will be shown.

Device Name Change the name of the selected LevelOne Printer Server if you wish. (This field is also on the Configuration-System menu.)
NDS Tree Name Select the NDS tree
Current Context Select Browse to view the NDS tree and select the appropriate Context.
Novell Printer Server for P1 (Parallel port 1)
Select the NetWare print server to service the LevelOne Printer Server's parallel port 1.
Novell Printer Server for P2, P3
Select the NetWare print server to service the LevelOne Printer Server's parallel port 2 (P2), parallel port 3 (P3).
Set to Default Replace the on-screen values with the default values. These are NOT saved until you click Save to Device. (No changes are made to the NetWare server.)
Save to Device Save any changes you have made to the LevelOne Printer Server
Cancel Ignore any changes made since the last Save operation; close the window.
Help View context-sensitive help.
NetWare · Data · Buttons

The following procedure is designed to enable Public Access Printing under DNPS, using TCP/IP. Public Access Printing allows anybody on the network to access the printer.
The procedure has 3 parts:


To create Public Access Printers using the NDPS Manager Object in NetWare Administrator, follow this procedure:

NetWare


Repeat this procedure for any other ports on the LevelOne Printer Server, or for any other logical printers you wish to use.
Before attempting to install and configure Public Access Printers on your workstation, ensure that:
Workstation Configuration


NetWare

This chapter covers configuration of the LevelOne Printer Server in a TCP/IP environment.
100BaseT LevelOne Printer Server models incorporate a HTTP server. This allows you to connect to the LevelOne Printer Server and configure it using your Web Browser. Most browsers should work, provided they support tables and forms.
Because it supports dynamic IP Address allocation using DHCP, BOOTP, or RARP, the LevelOne Printer Server ships with an IP Address of 0.0.0.0. This is NOT a valid IP Address.
Therefore, you must do ONE of the following:
arp -s IP_Address 00:c0:02:xx:xx:xx (Unix)
arp -s IP_Address 00-c0-02-xx-xx-xx (Windows)
Where: IP_Address is the IP Address you wish to assign to the LevelOne Printer Server 00:c0:02:xx:xx:xx is the hardware address of the LevelOne Printer Server.
Example (Unix):
arp -s 192.168.0.21 00:c0:02:12:34:56
Example (Windows):
arp -s 192.168.0.21 00-c0-02-12-34-56
The Default Server Name and the Hardware Address of the LevelOne Printer Server are shown on a sticker on the base of the device.

Connecting to the LevelOne Printer Server

Selecting TCP/IP will display the screen below.

IP Address The LevelOne Printer Server is able to obtain an IP Address dynamically, using DHCP, Bootp, or rarp. Normally, it will check these methods in sequence, but each method can be individually disabled using BiAdmin. (See Chapter 4). For more details on using Boop or rarp, refer to Chapter 8 - Unix.
Router (Gateway) IP Address
If your network segment has a router, enter the router address here. If there is no router, leave the address as 0.0.0.0.
If the Router is 0.0.0.0, the Network Mask should also be left at 0.0.0.0. If you have a router, enter the Network mask (Subnet mask) for the segment to which the LevelOne Printer Server is attached.
Delay before reconnection attempts
Sets how long the LevelOne Printer Server should wait before retrying a TCP/IP connection which is lost. Allowable values are from 0 to 255 seconds, with 2 as the default.
Number of reconnection attempts
Sets how many attempts at reconnection will be made. After that, the TCP/IP session will be terminated. Allowable values are from 0 to 255, with 254 as the default.
Network Mask

Logical Printer Configuration
Logical Printers can be used to create a “Virtual” printer. For example, to create a Landscape printer, you could define a Logical Printer as follows:
Pre-string Printer Control codes to switch the printer to Landscape mode
Post-string Printer Control codes to reset the printer, restoring the default settings.
Another logical printer could be used to print Unix-format text files for a DOS printer, by converting Unix-style LF (Line Feeds) to DOS-style LF/CR (Line Feed, Carriage Return) pairs.
The LevelOne Printer Server supports 8 Logical Printers. The names (L1..L8) cannot be changed. Each Logical Printer has 4 settings as shown below.
LevelOne Printer Server parallel port (P1 to P3) to which the printer is attached.
The printer control string (in hex) to be sent to the printer before each print job.
The printer control string (in hex) to be sent to the printer after each print job.
Convert LF to CR+LF
If ON, LF (line feed) characters are changed to CR+LF (carriage return + line feed). If OFF, no conversion is done.
The maximum size of printer control strings is 15 characters, and they must be entered in HEX.
Other screens which may be useful in a TCP/IP environment:
Physical Port · String Before Job · String After Job

Telnet can be used to monitor the status of the printers attached to the LevelOne Printer Server.
Establish a connection to the LevelOne Printer Server, by starting your Telnet program and providing the IP Address of the LevelOne Printer Server. (No port number is required.)
e.g. telnet 192.168.0.21
The LevelOne Printer Server will respond with "Welcome to Print Server". From the resulting prompt, 3 commands are possible:
The Monitor command will show the status of the printer on each port., as shown below. The display is updated once per second.
(P1)STATE: Idle TYPE: Parallel PRINTER STATUS: Out Of Paper (P2)STATE: Printing TYPE: Parallel PRINTER STATUS: On-Line BYTES SERVICED: 75264 OCCUPIED BY: LPD (P3)STATE: Idle TYPE: Parallel PRINTER STATUS: Idle

This chapter describes using your LevelOne Printer Server in the Unix environment.
The LevelOne Printer Server must be provided with a IP Address so that it will be a valid device on the LAN. This can be done using either Static or Dynamic IP Address configuration.
Where: IP_Address is the IP address for the LevelOne Printer Server. This address must match the address stored in the device. NAME is the LevelOne Printer Server’s name. This must match the name stored in the device. # comment. Add the Default Server Name as a comment. The Default Server Name is shown on a sticker on the base of the device.
Example:
192.10.2.54 PS_Rm203 #Default name PS123456 In the example above, PS123456 is assigned the IP address 192.10.2.54 and the name “PS_Rm203”.

If using bootp, no arp table entry is necessary, but the following configuration is required:
Where NAME is the LevelOne Printer Server’s name PA is the hardware address of the LevelOne Printer Server IP is the LevelOne Printer Server’s IP Address SM is the Subnet Mask GW is the Gateway IP Address
If using rarp, no arp table entry is necessary, but the following configuration is required:
There are 4 printing methods to choose from. All are explained in the following sections. Select whichever is the most convenient in your environment.
LPD is a standard print method for most UNIX systems. Using this method eliminates the need to install additional host softwaret. However, in many cases the LPD protocol sends out the data file before the control file. The LevelOne Printer Server will print the data file immediately, ignoring any print options set in the control file. To solve this problem, use PSfilter instead.
The Direct Socket Interface (DSI) is a Unix-based method of providing a “direct” connection between a host computer and a printer. The host and the LevelOne Printer Server establish a TCP connection, using a special socket number. All data sent over this connection is treated as print data, and sent transparently to a logical printer defined on the LevelOne Printer Server.
Psfilter is a proprietary print method provided with the LevelOne Printer Server as “C” source code. The benefit of this method is that it provides many print options such as banner print, copies, and so on. For details, see page 59.

FTP is also a standard print method in most UNIX systems, but it is NOT recommended except as a test and back-up method of printing, because it does not use a print queue.
LPD is a built-in printing protocol for most UNIX systems, and is also supported in Windows NT 3.5 or later.
Before proceeding, ensure that the LevelOne Printer Server has been assigned an IP Address. To setup your AIX system for LPD printing, perform the following steps.
Name of queue to add Use a single-word queue name which indicates which printer is attached.
Hostname for remote server
LevelOne Printer Server name as used in /etc/hosts.lpd.
Name of queue on remote server
Logical printer number (L1..L8) to service this queue.
Type of print spooler on remote server.
Use default value (AIX Version xxx)
Where printer_queue is one of the entries used in Name of queue to add. file_name is the file you wish to print.
Unix

Before beginning LPD Setup, ensure that an IP Address has been assigned to the LevelOne Printer Server. Keep the following points in mind:
Stop Print Services /usr/lib/lpshut
Add a System Printer /usr/lib/lpadmin -p printer_name -v /dev/null
Restart the Print Services /usr/lib/lpsched
Enable printing to the new printer device
Start accepting jobs for the new printer device
Create a spooling directory mkdir /usr/spool/Spooler_directory
Make spooling daemon the owner of this directory
Create read/write permissions chmod 775 /usr/spool/Spooler_directory
Give permissions to LPD processes.
Add remote printer(s) See following section.
A remote printer is added by inserting the following line in the /etc/printcap file.
The entry is really one line, but can be entered as shown. Use a TAB character where shown.
printer_name|Remote_Printer_Alias:\ [TAB] :lp=:\ [TAB] :rm=PS_NAME:\ [TAB] :rp=Logical_Printer_name:\ [TAB] :sd=Spooler_directory:\ [TAB] :mx#0:

Where:
printer_name is the Print Queue name used to store jobs for the corresponding logical printer PS_NAME is the LevelOne Printer Server name defined in /etc/hosts Logical_Printer_name is the logical printer name on the LevelOne Printer Server (L1..L3 or L1..L8, depending on your model) Spooler_directory is the directory you created in Step 6. Example:
Marketing|RP1_PS123456:\ [TAB] :lp=:\ [TAB] :rm=PS_Rm203:\ [TAB] :rp=L1:\ [TAB] :sd=/usr/spool/Marketing:\ [TAB] :mx#0:
Repeat this process for each Logical Printer/Print Queue combination that you wish to create.
Before continuing, ensure that an IP Address has been assigned to the LevelOne Printer Server. Remember the following:
Create a spooling directory mkdir /usr/spool/Spooler_dir
Set spooling daemon as owner of this directory.
Create read/write permissions. chmod 775 /usr/spool/Spooler_dir
Give permissions to LPD processes. chgrp daemon /usr/spool/Spooler_dir
Add remote printer(s) See below.
Start lpc print mechanism lpc start printer_name
Unix · Action Sample Command · chown daemon /usr/spool/Spooler_dir

A remote printer is added by inserting the following line in the /etc/printcap file.
The entry is really one line, but can be entered as shown. Use a TAB character where shown.
printer_name|Remote_Printer_Alias:\ [TAB] :lp=:\ [TAB] :rm=PS_NAME:\ [TAB] :rp=Logical_Printer_name:\ [TAB] :sd=Spooler_directory:\ [TAB] :mx#0:
Where:
printer_name is the Print Queue name used to store jobs for the corresponding logical printer PS_NAME is the LevelOne Printer Server name defined in /etc/hosts Logical_Printer_name is the logical printer name on the LevelOne Printer Server (L1..L3 or L1..L8) Spooler_directory is the directory you created in Step 6.
Example:
Marketing|RP1_PS123456:\ [TAB] :lp=:\ [TAB] :rm=PS_Rm203:\ [TAB] :rp=L1:\ [TAB] :sd=/usr/spool/Marketing:\ [TAB] :mx#0:
Repeat this process for each Logical Printer/Print Queue combination that you wish to create.
For LPD printing instructions, refer to your UNIX manual. The following example is for a BSD system:
lpr -P printer_name filename
Where: printer_name is the name of the Print Queue defined on the Unix host. filename is the name of the file you wish to print.
Example:
lpr -P Marketing /etc/hosts
In the above example, the /etc/hosts file is sent to the printer queue Marketing. It will then be sent to the logical printer associated with this queue.

Your LevelOne Printer Server supports 2 other printing methods:
Logical printers must be configured on the LevelOne Printer Server as explained in Chapter 7 - TCP/IP (DSI supports only 3 Logical Printers). Socket numbers are defined as follows:
Logical Printer No. Socket No. 1 4010 2 4020 3 4030
PSfilter is a proprietary print method provided with the LevelOne Printer Server as “C” source code. It provides many print options. To use PSfilter, a C compiler and Socket Library must exist on the host so that psfilter.c can be compiled to an executable file.
The PSfilter program is shipped in source code as psfilter.c. Detailed instructions for installing, configuring, and using PSfilter are provided in the following files. These files, along with PSfilter.c, are stored on the CD-ROM in the following directories:
PS\driver\lpti\lpsource (text format) PS\driver\lpti\tar (tar format)
SCO UNIX System V Release 3 SCO.TXT
HP UXIX on HP workstation HP.TXT
Sun 5.x on Sun SPARC workstation SUN5.TXT
Sun 4.x on Sun SPARC workstation SUN4.TXT
AT&T UNIX SV Release 4 SVR4.TXT
IBM AIX AIX.TXT
UNIXWare UNIXWARE.TXT
If your system is not listed above, do not attempt to use the PSfilter method of printing.
Unix · Operating System Filename

This chapter explains how to configure and use your LevelOne Printer Server in the Windows NT Server TCP/IP environment.
Refer to Chapter 7 - TCP/IP for details on configuring the LevelOne Printer Server. It must have a valid IP Address.
Note that if you have a DHCP server, the LevelOne Printer Server is assigned an IP Address of 0.0.0.0. It will then obtain an IP Address from the DHCP server. But using DHCP is only feasible if you have DHCP management software which allows you to take advantage of this feature. Otherwise, the LevelOne Printer Server’s IP Address will be unknown, and connection to it will be impossible. In this case, configure the LevelOne Printer Server for a static IP Address.

Windows NT Server (TCP/IP)
This section covers configuration of a Windows NT host. The LevelOne
should be configured first. For Windows NT configuration in a Peer-to-Peer environment, see Chapter 10 - Windows Peer-to-Peer.
If you wish to refer to the newly-installed LevelOne Printer Server by its name, rather than by its IP Address, you must add an entry for it to the hosts file
The entry consists of the following line:
xxx.xxx.xxx.xxx Name
Where xxx.xxx.xxx.xxx is the IP Address you assigned to the LevelOne Printer Server and Name is the LevelOne Printer Server’s name. This should match the name stored in the LevelOne Printer Server itself. If you have not changed the name, use the Default Server Name shown on a sticker on the base of the device.
You can check that this has worked using the ping command, as follows:
Where Name is the value used in the host file.
You should receive a response. If you get a Timeout message, there is a problem. If you repeat the command using the IP Address instead of Name, and get a response, then the problem is the entry in the host file.
ping Name

To create a TCP/IP remote printer, Microsoft TCP/IP Printing Support must be installed. If it is already installed, proceed to Adding a TCP/IP Remote Printer. Otherwise, the procedure to install TCP/IP printing support is as follows.
Windows 3.51
Printer Name Enter a name (up to 32 characters). This name appears in the title bar of the printer window.
Driver Select the appropriate driver for the attached printer.
Description Enter a printer description for other network users to reference.
Print To Select Other.
Name Or Address Of Host Enter the IP address of the LevelOne Printer

Windows NT Server (TCP/IP)
Name Of Printer On That Machine
Enter the appropriate logical printer number (L1..L8)
Providing LPD Server

The LevelOne Printer Server’s printers will appear as Network Printers to users on the LAN.
To print a file from the command prompt, type:
lpr -S NT_Host -P printer_name file_name
Where: NT_Host is the name of the NT host on which the remote printer is configured. printer_name is the name assigned to the remote printer file_name is the name of the file you wish to print.
To check the print status, type:
lpq -S NT_Host -P printer_name

This chapter describes operation in a Windows Peer-to-Peer Networking environment.
In a peer-to-peer environment, each PC communicates directly with the LevelOne Printer Server.
The LevelOne Printer Server supports both NetBEUI and TCP/IP. Both protocols can be used simultaneously.
The following Windows versions are supported:
Before performing the following procedure, the LevelOne Printer Server must be installed on your LAN. Both the LevelOne Printer Server and the attached printer should be powered ON.


If you see the following error message, you need to install Internet Explorer 4 or later.



Windows Peer-to-peer

The options for the Peer-to-peer Print Driver are accessed via the Port Settings button.
Use Start - Settings - Printers to open the Printers folder, then right-click the Printer, and select Properties. The Port Settings button is on the Details or Ports tab, depending on your version of Windows.
An example screen is shown below:

Items shown on this screen are as follows:
Port If desired, click Browse to select a different LevelOne Printer Server. If the selected device has multiple ports, the Select Device Port button can be used to select the port.
The Port Name can not be changed after installation. This name is shown in the Printer's Properties.
Banner Check this option to print a banner page before each print job.
Retry Interval Sets how often Windows will poll the LevelOne Printer Server to establish a connection when the printer is busy. Increase this value if you get too many warning messages.

This chapter covers the special features of the LevelOne Printer Server.
When using the TCP/IP protocol, the LevelOne Printer Server supports 2 special features:
The Internet Printing System allows users (employees, colleagues, suppliers, customers…) to print data to your printer across the Internet.
Users send the Internet LevelOne Printer Server an E Mail, with the print job normally sent as an attachment to the E Mail.
The LevelOne Printer Server will retrieve the E Mail and print it, using the printer attached to port 1.
Mail Server


The LevelOne Printer Server must be configured with the data in the following table. This can be done with either the supplied BiAdmin utility program (see Chapter 4) or your Web Browser (see Chapter 7).
Mail Server IP Address
The IP Address of the E Mail Server used by the LevelOne Printer Server.
Mail Account The name of the E Mail Account used by the LevelOne Printer Server.
Mail Account Password Enter the password for the above Mail Account here.
Check Mail Interval Sets how often to check for mail. Values range from 0 to 65,535 minutes, with 0 meaning a continuous connection and 1 as the default.
Print Banner If YES (default), a banner page is printed to identify the owner of the print job.
Redirect Mail Account Jobs which can not be printed will be sent to this account. If blank, unprintable jobs will be discarded.
Default Printer Number Printer number for all Internet print jobs. Only one port can be selected. Users on the LAN can also use this port.
Print every E-Mail If ON, then all E Mail received is printed. Otherwise, only E Mail from the InterNet Printing Port will be printed.
Activate Response Mail If YES, all print jobs receive an E mail response. If NO, only users who set this option in their InterNet Printing Port software receive an E Mail
Printer Model ID String This text field identifies the printer used for Internet printing. This value is sent to remote users upon request.
The software provided for remote users (InterNet Printing Port) should be installed by everyone intending to use Internet printing. Otherwise, remote users can print correctly only if:
Installation of the InterNet Printing Port software will create a new printer port. After attaching the correct printer to this port, users can print to the Internet Printer using any Windows application.
Special Features


Port Name Enter a descriptive name (e.g. “WAN”) for the new printer port.
Remote Printer E-mail Address
The E Mail address for the Internet printer. Your print jobs will be sent to this E Mail address.
This is the name or IP Address of your Mail Server. If you are on a LAN, ask the LAN Administrator. If using a dial- up connection, use the data provided by your ISP.
Mail Server Name or IP Address
Your Internet E-mail Address
The normal address that people use to send you E-mail.
If unable to connect to the E Mail server, retry after this time period (1 to 255 seconds, 30 is usually OK).
Check to receive an E Mail when your print job has been processed.
Retry Interval (Seconds) · Reply Notification Mail

The Windows Control Panel is used to connect the correct printer to the InterNet Printing Port. In Windows 95/98/NT, the procedure is:

To make sure that the correct printer driver for the remote printer is installed on your system, you can use the InterNet Printing Port to send an E Mail to the Internet Printer. The procedure is as follows:
You will receive a reply E Mail containing the “Printer ID” which will identify the printer attached to the LevelOne Printer Server. If this does not match the printer driver you are using, install the correct printer driver.
Special Features


Users cannot cancel a Print Job once it has been sent, but Print Jobs can be canceled at the LevelOne Printer Server. In BiAdmin, the Control - Abort Mail Print Job menu option can be used to cancel a print job which has already started printing.

The LevelOne Printer Server supports SNMP (Simple Network Management Protocol).
The LevelOne Printer Server’s SNMP support allows network supervisors to monitor and control the LevelOne Printer Server using network management platforms such as HP OpenView, IBM SystemView, etc. This is accomplished through the SNMP agent and the SNMP MIB.
The agent (device software) responds to standard SNMP commands and reports device configuration and conditions. When a change in condition occurs, the SNMP agent will send a message (a Trap) to the associated management station.
The LevelOne Printer Server’s SNMP MIB is a collection of objects that are monitored and controlled using SNMP’s get and set commands. The appropriate .MIB file must be imported into your SNMP management program using the Import-Compile command. Check your management program for details on this procedure.
The MIB files are in the provided in the \PS\MIB folder on the CD-ROM.
Use the Import - Compile command of your SNMP program to import the Mib file for your model.
Before using a SNMP Management station to manage the LevelOne Printer Server, the following settings should be assigned to it, in addition to standard TCP/IP settings covered in Chapter 7 - TCP/IP.
SysContact Text Field - Name of the contact person.
SysLocation Text Field - Location of the contact person.
Management Station IP Address(s)
Up to 4 Management Stations can be entered.
Trap Receiving IP Address(s)
Up to 4 Trap Receiving Stations can be entered.
For each Management Station, the following fields are available.
Access Permission Options are:
Read Only Read/Write Not Accessible.
Community String Leaving this blank will disable management by this station.
For each Trap Receiving Station, the following fields are available.
Community String Leaving this blank will disable management by this station.
Trap Enable Use this option to Enable/Disable Trap Receiving by this station.
Special Features

Trap Severity In this version, all traps are level 1. Levels 2 and 3 will be implemented in future versions.

This chapter describes some problem situations which may arise, and the solutions to them.
If you encounter printing difficulties, please refer to the Hardware section first, then the Printing section, then the section for your specific situation.
If, after following the advice in these documents, the LevelOne Printer Server still does not function properly, please contact your dealer for further advice.
Problem No. 1 All the LevelOne Printer Server’s LEDs are off.
Solution No. 1 Check the power supply or power connection.
Problem No. 2 LevelOne Printer Server’s status light continuously stays lit.
Solution No. 2 Reset LevelOne Printer Server by unplugging the power supply and plugging it back in.
Problem No. 3 LevelOne Printer Server status light and power light stays on continuously and do not turn off.
Solution No. 3 Reset LevelOne Printer Server by unplugging the power supply or by pushing the reset push button.
Problem No. 4 I am using DHCP, and getting an IP Address conflict involving the LevelOne Printer Server.
Solution No. 4 If the LevelOne Printer Server is left on, but the DHCP server is turned off, then the LevelOne Printer Server will retain its IP Address without the DHCP Server being aware of it. Simply reset the LevelOne Printer Server so it will obtain a new IP Address.
This problem would also arise if you assigned a static IP Address which is within the range used by the DHCP server. If so, use another address which is NOT within the range used by the DHCP server.
Problem No. 5 I am using WPConfig on Windows 95, and having problems configuring the LevelOne Printer Server.
Solution No. 5 WPConfig is designed for Windows 3.1 only. For Windows 95/NT, you should use BiAdmin.

Problem No. 1 When using 10BaseT cabling, the LevelOne Printer Server unit does not work.
Solution No. 1 Check the Hub’s link LED for the port to which the LevelOne Printer Server is connected. If it is off, there is a problem in the network cable. If using 10BaseT or 100BaseT, check the LED next to the connector. It should be on if the network connection is OK.
Problem No. 2 A printing device connected to the a LevelOne Printer Server port cannot print or prints garbage.
Solution No. 2 Check the following:
Problem No. 3 The Configuration button on the Printer Status screen in BiAdmin is grayed out, even though my printer in bi- directional.
Solution No. 3 The button is unavailable if the printer is busy. You must wait until the printer is idle.

Problem No. 1 Why do I get an incorrect printout?
Solution No. 1 Some possible reasons are:
Problem No. 2 Can’t find the LevelOne Printer Server’s name in the Chooser.
Solution No. 2 Try the following:
Problem No. 3 My document didn’t print to the right printer.
Solution No. 3 Check the following:
Problem No. 4 My file doesn’t print with the correct fonts.
Solution No. 4 Try using the LaserWriter 7 printer driver.
Problem No. 5 My EPS file doesn’t print with the correct fonts.
Solution No. 5 This is a problem that occurs in some application programs. Try downloading the fonts contained in the EPS file before printing the saved EPS file.
Problem No. 6 I can’t select the “Remaining from:” item in the print dialog box.
Solution No. 6 If you have selected the Layout value, 2 Up, or 4 Up, you cannot access the Remaining from: item. Choose other selections.
Problem No. 7 A cover page prints either on the first or the last page of the document.
Solution No. 7 Select one of these solutions:
Troubleshooting

page printing on the first or last page of your document.
Problem No. 8 Why do I have trouble printing with the LaserWriter 8?
Solution No. 8 Your application software may not be compatible with the LaserWriter 8 driver or your system may not meet the requirements of the LaserWriter 8 driver. Use the Apple LaserWriter 7 driver instead.
Problem No. 9 How come the colors on my printed output do not match the colors on my computer screen?
Solution No. 9 When the printer receives a color file, it tries to match the printed output color to the screen color. Sometimes the printer cannot match up the colors as closely as wanted. To alleviate this problem, perform the following steps:
Problem No. 10 The blue color I chose on my computer screen is printing out purple.
Solution No. 10 Choose Calibrated Color/Grayscale in the Print pop-up menu in the Print Options dialog box.
Problem No. 11 When I send a print job, I get a PostScript Command error or no print out.
Solution No. 11 Check the communication protocols. The computer, LevelOne Printer Server and printer must all be configured to the same communication protocol.(either Binary or ASCII).
To configure your system:

Problem No. 1 My LevelOne Printer Server prints garbage.
Solution No. 1 Follow the following steps to identify the problem:
the list. Then select Print Diagnostic Report (b) Select each port in turn and print a diagnostic report. (c) Check to see if the diagnostic report printed OK. If the
diagnostic report printed OK, the problem may be caused by incorrect system configuration. Go to Step 2. If the diagnostic report printout is not OK, check your printer. If your printer is OK, call your dealer.
NetWare 2.x and 3.x (a) Run PCONSOLE, Select Print Queue Information, select the
print queue that the LevelOne Printer Server services, select Current Queue Status. (b) Set Servers can service entries in queue to NO. (c) Press Esc and select Print Queue ID. Record its queue ID. (d) Send your test files to the print queue using normal print
commands.
NetWare 4.x bindery and NDS modes (a) Run PCONSOLE, select Print Queues, select the print queue
that your LevelOne Printer Server services, select Status. (b) Set Allow service by current print servers to NO. (c) Press Esc and select Information, and record its queue ID. (d) Send your test files to the print queue using normal print
commands.
Server and connect it to LPT1 of your PC. (b) Change to the drive and then the directory on the file server
that contains the print queue. The directory will have the name of the queue ID (e.g. \queues\Q_ID for NDS mode or system\Q_ID for Bindery mode).
Troubleshooting

Problem No. 2 My LevelOne Printer Server does not appear in the Active Device List of the PSConfig program.
Solution No. 2 • Ensure that the LevelOne Printer Server is on the same network segment as your PC.
Problem No. 3 My LevelOne Printer Server is configured as a Novell Print Server, and cannot log in to a file server.
Solution No. 3 The following steps may solve this problem:
Server Name: PS110049 NetWare Information: Master File Server: ICE Print Server Mode Status: Your_File_Server: Current Status Remote Printer Mode Status: N/A

Problem No. 4 My LevelOne Printer Server is configured as a Novell Remote Printer, and can’t log in to the Novell Print Server.
Solution No. 4 Try the following steps:
Problem No. 5 My LevelOne Printer Server cannot print the jobs sent to the print queue.
Troubleshooting

Solution No. 5 Try the following.
Problem No. 6 I used the Capture command to print a job, but the job was separated into two parts.
Solution No. 6 The time out setting in the Capture command may be too short. You should increase the timeout value of the Capture command. Use the option /TI=n of the Capture command to increase the time out value, where n is the value of timeout.
Problem No. 7 PSConfig shows "No Response."
Solution No. 7 This may be due to the following
Problem No. 8 QUICKSET timed out when checking if the device had logged in to the file servers.

Solution No. 8 This means that the LevelOne Printer Server did not log in the master file server. It might be that the Ethernet frame types do not match.
Problem No. 9 I cannot receive Notify message in NetWare 4.x environment.
Solution No. 9 • Make sure you are a Notify member of the Print Server.
Problem No. 10 I cannot use PCONSOLE to see Printer Status or the current server status in Print Server Information is showing Down in the NetWare 4.x environment.
Solution No. 10 It may be that you created the print server object in NetWare 3.x environment and used PCONSOLE in NetWare 4.x to view the status. Try the following:
Problem No. 11 The “String Before Job” and/or “String After Job” settings in the Logical Printers don’t work properly.
Solution No. 11 • Check the length of the control strings. No string can exceed 15 characters.
Troubleshooting

Problem No. 1 LevelOne Printer Server device is not recognized.
Solution No. 1 Check the following:
Problem No. 2 The standard interface program on SUN 5.2 cannot be used with Psfilter.
Solution No. 2 Use dumb_int.sh which is the interface program shipped with LevelOne Printer Server.
Problem No. 3 When the interface program detects that the printer device is not a printer, a printer error message appears on the screen.
Solution No. 3 Mark out all stty commands in the interface script.
Problem No. 4 The .psopts file format is not accepted by BSD UNIX.
Solution No. 4 If the prefix or and suffix string must contain control words or are too long, use headfile or tailfile instead of prefix string or suffix string.
Problem No. 5 The LevelOne Printer Server’s IP address is forgotten and it needs to be installed in a new environment.
Solution No. 5 Follow the steps below to set the LevelOne Printer Server back to the factory default configuration.
Where: yyy.yyy.yyy.yyy is the new IP address assigned to the LevelOne Printer Server 00:c0:02:xx:xx:xx is the hardware address, as shown on a sticker on the base of the LevelOne Printer Server.
This will reset the configuration to the factory defaults (including setting the IP address back to 0.0.0.0).

Problem No. 6 Printing by FTP, I receive an error message: Invalid print queue Print queue not ready
Solution No. 6 • Check that the printer is ready
Problem No. 7 I can’t print using LPD.
Solution No. 7 Try printing with FTP. If this works, the problem is the LPD daemon on your UNIX host. Reconfigure the remote printer and the LPD daemon. Check the following points.
Problem No. 8 I can’t print using PSfilter,
Solution No. 8 Run PSfilter directly with the command:
PSfilter -D P_name -v
Where:
P_name is the LevelOne Printer Server’s name file_name is the file you wish to print.
If this fails, check for an error log file (e.g. PSErrLog XXXXX) in the /tmp directory. If there is not an error log file, recompile PSfilter. Also, check the Troubleshooting section of the Psfilter .TXT file for your system.
Problem No. 9 The “String Before Job” and/or “String After Job” settings in the Logical Printers don’t work properly
Solution No. 9 • Check the length of the control strings. No string can exceed 15 characters.
Troubleshooting

Problem No. 1 When I tried to install the Printing software for Peer-to-Peer printing, I received an error message and the installation was aborted..
Solution No. 1 This may be caused by an existing installation of the printer port software. Before attempting another installation:
To remove an existing printer port installation:
Problem No. 2 On Windows 95, I installed the Print Port Driver for Peer-to- Peer Printing, but when I selected a port on a Print Server and clicked "Add", the printer was not installed.
Solution No. 2 Try installing the Printer using the standard Windows tools, as follows:


Details tab, as shown below.


Troubleshooting



The Printer should no longer be grayed out, and is ready for use.
Problem No. 3 I connected and configured a WPS (Windows Printing System) printer as described, but I can't get the print job to print.
Solution No. 3 Printer drivers for WPS printers poll the printer before sending print data. Since the printer is networked, the printer is not found and no data is sent. The solution is to add your printer as a network printer as described in Solution 1 above.
Problem No. 4 When printing from some software applications such as Power Point, it takes a long time and the print out is incorrect.
Solution No. 4 The problem is due to the printer, which is being configured to Start printing after the first page is spooled. To change this setting:

Problem No. 5 A printing device connected to the LevelOne Printer Server port cannot print or prints garbage.
Solution No. 5 Check the following:
Problem No. 6 The Configuration button on the Printer Status screen in BiAdmin is grayed out, even though my printer is bi- directional.
Solution No. 6 The button is unavailable if the printer is busy. You must wait until the printer is idle.
Problem No. 1 I don’t know my Mail Server’s IP Address.
Solution No. 1 Use the PING command to connect to the Mail Server by name. Example
The reply will say:
Problem No. 2 Plain text E Mails are not printed.
Solution No. 2 Text E Mail messages are printed only if the LevelOne Printer Server is configured with Print every E Mail ON.
Problem No. 3 Plain text E Mails print OK., but if I include an attachment, I get an E Mail reply “Wrong Encoding Method”.
Solution No. 3 The Internet Printer system supports only Base64 encoding. Using the Internet Printing Port driver will ensure a correctly encoded attachment..
Problem No. 4 A print job is printing garbage.
Solution No. 4 Users must use the correct printer driver. The print job can be canceled using the Control - Abort Mail Print Job menu option in the BiAdmin program.
Problem No. 5 Two print jobs are printing on the same page.
Solution No. 5 Change the port used for Internet Printing from a physical port to a Logical Port (Printer). Configure the Logical Printer so that the String
Troubleshooting

after Job contains a FF (Form Feed, decimal 12 or 0C in Hex). See the section on Logical Printers in the Unix or NT Server sections for details of Logical Printers.
Problem No. 6 The Print job seemed to go through OK, but it was never received.
Solution No. 6 Check the E Mail address. If you use more than one Internet Printer with the same printer driver, ensure that you use the correct port each time you print.
Problem No. 7 Only the banner page was printed.
Solution No. 7 This could be caused by using the wrong encoding method. Ask the user to use the InterNet Printing Port.
Also, some printer drivers, when configured as Local Printer, will poll the printer to see if it is connected. Since the printer is networked, the printer can not be detected. To fix this, perform the following:
If the printer is connected and powered On, the printer icon should no longer be grayed out, and you should be able to print.
Problem No. 8 The Banner page is not correct; the first row has disappeared.
Solution No. 8 This may be caused by the previous print job not sending a form feed after finishing printing. Try sending print jobs to a logical printer, which is defined with a Post String of FF (Form Feed - 0C in Hex).
To do this, define the Logical Printer, and set the port used for Internet Printing to this Logical Printer.

Power Consumption 3w max.
External Power Adapter 9V DC
Parallel Port 1 Male DB-36 connector
This equipment generates, uses, and can radiate radio frequency energy. It has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a domestic environment.
Operation is subject to the following two conditions:
This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Power Consumption 4w max.
External Power Adapter 5V DC
Parallel Port 1 Male DB-36 connector
This equipment generates, uses, and can radiate radio frequency energy. It has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a commercial environment.
Operation is subject to the following two conditions:
This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Operating Temperature 0 ~ 40°C Storage Temperature -10 ~ 70°C Shipping Temperature -40 ~ 70°C Operating Humidity 10 ~ 80% Storage Humidity 5 ~ 90% Shipping Humidity 5 ~ 100%
Parallel Port Pin Assignments
Pin Signal Name Source 1 -Strobe H 2 +Data 1 Bi-Di* 3 +Data 2 Bi-Di* 4 +Data 3 Bi-Di* 5 +Data 4 Bi-Di* 6 +Data 5 Bi-Di* 7 +Data 6 Bi-Di* 8 +Data 7 Bi-Di* 9 +Data 8 Bi-Di* 10 - ACK P 11 + Busy P 12 + Paper Error P 13 + Select P 14 - Auto Feed H 15 Not Defined 16 Logic GND 17 Chassis GND 18 Peripheral Logic High P 19-30 GND 31 -Init H 32 -Fault P 33-35 Not Defined 36 -SelectIn H
∗ Data signals will be driven by some but not all peripheral devices.
Specifications · Environmental Specifications


Parallel Port 1 Centronic female DB-25 connector, ECP compatible
Parallel Port 3 Centronic female DB-25 connector, ECP compatible

This equipment generates, uses, and can radiate radio frequency energy. It has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a domestic environment.
Operation is subject to the following two conditions:
This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.


Pin Signal Name Direction 1 -Strobe To printer 2 +Data 0 To printer 3 +Data 1 To printer 4 +Data 2 To printer 5 +Data 3 To printer 6 +Data 4 To printer 7 +Data 5 To printer 8 +Data 6 To printer 9 +Data 7 To printer 10 - ACK To Server 11 + Busy To Server 12 + Paper End To Server 13 + Select To Server 14 - Auto Feed To printer 15 - Error To Server 16 - Init To printer 17 - Select In To printer 18-25 GND Ground
Specifications · FCC Statement · CE Marking Warning


What the fault codes shown on the display mean and how to clear them.
| Code | Meaning | Fix | |
|---|---|---|---|
| OF56 | If so, reduce the number of queues. | p.87 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.