EN
LevelOne logo
Official user manual

LevelOne 4100

38 pages·1004 KB·Stereo System·PDF·ENDEFRITNLJA
LevelOne 4100
Table of Contents 41 sections LevelOne VoIP · User’s Guide · VOI-1110 · VOI-2100 · … ShowHide
Page 1 of the LevelOne 4100 user manual — LevelOne VoIP
Page 1 · click to enlarge
Page 1
LevelOne 4100 — LevelOne VoIP diagram (page 1)
Fig. 1 · LevelOne VoIP

LevelOne VoIP

User’s Guide

VOI-1110

VOI-2100

VOI-2110 VOI-4100

Page 2 of the LevelOne 4100 user manual — LevelOne VoIP
Page 2 · click to enlarge
Page 2

Contents are subject to revise without prior notice.

All trademarks belong to their respective owners.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause radio interference in which case the user will be required to correct the interference at his or her own expense.

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

USER’S GUIDE Part No.: 06310081011

Show 4 more labels / short text on this page
Trademarks · FCC Warning · CE-mark Warning · Revision
Page 3 of the LevelOne 4100 user manual — LevelOne VoIP
Page 3 · click to enlarge
Page 3
Page 3 of the LevelOne 4100 user manual — LevelOne VoIP
Page 4 of the LevelOne 4100 user manual — 1. About this guide
Page 4 · click to enlarge
Page 4

1. About this guide

Congratulations on your purchase of this outstanding LevelOne VoIP SIP Gateway. This guide is to cover the settings for VOI-1110 with 1-FXS port, VOI-2110 with 2-FXS port, VOI-2100 with 1-FXS/1-FXO port, and VOI-4100 with 4-FXS port. Please refer to below messages to choose those setting instructions that are related to the model purchased.

(a) For VOI-1110 with 1-FXS and VOI-2110 with 2-FXS , they are almost with the same setting instructions. The only difference is that 1-FXS model has only ONE Line (Line1) for setting in the User Interface (UI), SIP Configuration – Gateway settings. (b) For VOI-2100 with 1-FXS/1-FXO model, it has one extra setting UI for FXO port. Please refer to Appendix B for setting instructions. (c) For VOI-4100 with 4-FXS model, it does not have LAN port. Please disregard the UI for LAN settings and for WAN – MAC Spoofing Configuration. And, you will find FOUR Lines (Line 1 to Line 4) for settings in the UI, SIP Configuration – Gateway settings. For the SIP settings in this manual, we use the compatible settings with FWD, www.freeworlddialup.com This manual is subject to changed without notice if the settings of FWD are revised or by any other factors. Please visit www.freeworlddialup.com for more setting information or visit www.level1.com for product update information. LevelOne is not affiliated with FWD. The LevelOne VoIP SIP Gateway also works with majority of other SIP proxy service.

Page 5 of the LevelOne 4100 user manual — 2. Hardware Setup
Page 5 · click to enlarge
Page 5

2. Hardware Setup

It is highly recommend that connect the SIP gateway behind a NAT router. Following configurations are assumed that you will connect the SIP gateway behind a NAT router. 1. Connect the power adapter to the power outlet. After flashing, the POWER LED will be lit.. 2. Connect the RJ45 WAN port to your router. 3. Connect the RJ11 phone port to a Telephone set. 4. Connect the RJ45 LAN port to your computer for later configuration.

For VOI-2100, there is a “line” port, which is FXO port. The setting of FXO port can be found in the Appendix B. All the ”phone” port mentioned in this chapter refers to FXS port.

Page 6 of the LevelOne 4100 user manual — 3. Login to Web management page
Page 6 · click to enlarge
Page 6

3. Login to Web management page

After connecting your computer to the LAN port of SIP Gateway, you can login the configuration page by open a browser and type 192.168.1.1 in address column. The default login name is “root”. For VOI-4100, there is no LAN port on this model. You have to connect your computer to WAN port of VOI-4100, and configure the TCP/IP setting of your computer manually. Set the IP address as 192.168.1.XXX. After set successfully, open a browser and type 192.168.1.1 in address column. The default login password is “root”. The login page is shown as following.

LevelOne 4100 — 3. Login to Web management page diagram (page 6)
Fig. 2 · 3. Login to Web management page

Fig.1 Login Page

Set correct IP configuration to SIP gateway.

After login Successfully, you can see the welcome page as following.

LevelOne 4100 — 3. Login to Web management page diagram (page 6)
Fig. 3 · 3. Login to Web management page
Page 7 of the LevelOne 4100 user manual — 3. Login to Web management page
Page 7 · click to enlarge
Page 7

Click WAN/WAN Settings, and set correct settings to SIP gateways corresponding to your NAT router. The settings in the following image is suitable for LevelOne FBR-1407/1409TX/1411TX/1412TX/1413TX/1415TX/1417TX/ 1418TX and WBR-3402/3403TX/3404TX/3406TX. Please avoid the possible IP conflict in your LAN environment.

LevelOne 4100 — 3. Login to Web management page diagram (page 7)
Fig. 4 · 3. Login to Web management page

After setting, please click “Reboot” at the left menu and connect your computer to router. And you can configure the SIP Gateway by typing the new set IP address in your web browser. Please be noted that once the settings are changed, you must click “Reboot” at the left menu for the changes to be effective. For all the other web page settings, “Reboot” is also required for the changes to be effective.

Page 8 of the LevelOne 4100 user manual — 4. Home
Page 8 · click to enlarge
Page 8

4. Home

LevelOne 4100 — 4. Home diagram (page 8)
Fig. 5 · 4. Home

System Uptime: specifies the amount of time, which the system has been up.

This time is reset every time the system is reset.

LAN IP Address: indicates the IP Address of your LAN.

MAC address: MAC address is the address of your MAC.

Security: for your password, which is configured in the “System” section.

Application Code Versiontells the version of the application code which you

are using.

Download Code Versiontells the version of the download code which you are

using.

Page 9 of the LevelOne 4100 user manual — 5. WAN
Page 9 · click to enlarge
Page 9

5. WAN

WAN status

LevelOne 4100 — 5. WAN diagram (page 9)
Fig. 6

Interface Status: these are the details of your interface’s status.

Enabled“Yes”, lets you know that your interface is enabled and ready to be

used.

Serviceeither “Routed or Bridged”, tells you the level of your interface’s

connection.

Protocolrefers to how you are transmitting data. (i.e. Ethernet)

Interface Status: either “Up” or “Down”.

Under Network Settings: these are the details of your network settings.

Page 10 of the LevelOne 4100 user manual — 5. WAN
Page 10 · click to enlarge
Page 10
Dynamic IP Assignment“Yes” or “No”, depending on whether or not you are

using a dynamic IP.

IP address: your specified IP.

MAC address: Your specified MAC address.

Subnet Mask: indicates the IP address of your mask. Default Gateway: is the IP address of the gateway. The gateway IP could be

retrieved from DHCP offer in DHCP mode, or be set up manually in fixed IP mode.

DNS address: refers to the address of your dynamic name server, if applicable.

VLANVLAN tag value encoded in the Ethernet header in all outgoing packets
Priority TagPriority Tag value encoded in the Ethernet header in outgoing

packets.

Broadcast Limit & Multicast LimitPlease see the WAN Setting
Page 11 of the LevelOne 4100 user manual — WAN Settings
Page 11 · click to enlarge
Page 11

WAN Settings

LevelOne 4100 — WAN Settings diagram (page 11)
Fig. 7 · WAN Settings
1. Device Operating Mode: you choose either “Router” or “Bridge”, depending on your operation.
2. You will check either “ Obtain WAN configuration dynamically ” or “ Specify fixed WAN configuration ”.

When you choose “Obtain WAN configuration dynamically”, the information is detected automatically through DHCP.

If you choose “Specify fixed WAN configuration”, you are required to enter the IP address, IP of the Sub mask, IP of the Gateway, and IP of the DNS Server, if applicable.

3. Multicast Limits: Broadcast Limit: the value specifies the maximum limit on the percentage of

broadcast packets, which will be bridged to the destination interface (as a percentage of the source side bandwidth)

Page 12 of the LevelOne 4100 user manual — WAN Settings
Page 12 · click to enlarge
Page 12
Multicast Limitthe value specifies the maximum limit on the percentage of

multicast packets, which will be bridged to the destination interface (as a percentage of the source side bandwidth)

Page 13 of the LevelOne 4100 user manual — WAN PPPoE Configuration
Page 13 · click to enlarge
Page 13

WAN PPPoE Configuration

LevelOne 4100 — WAN PPPoE Configuration diagram (page 13)
Fig. 8 · WAN PPPoE Configuration
1. Enable PPPoE: “Yes” or “No”, to enable/disable PPPoE
2. Under “ Authentication ”, you enter the username and password given by your ISP.
3. Settings: Idle Timeout: Idle timeout before PPP connection is closed due to inactivity Echo Timeout: the duration between PPP echo requests being sent to the

server.

Echo Countthe number of unanswered PPP echo requests before the PPP

connection is closed.

Service NamePPPoE Service name AC Name: PPPoE AC name

We do not suggest that using LevelOne VoIP SIP Gateway as a Router. Please connect it behind another NAT router for safety reason.

Page 14 of the LevelOne 4100 user manual — MAC Spoofing Configuration
Page 14 · click to enlarge
Page 14

MAC Spoofing Configuration

LevelOne 4100 — MAC Spoofing Configuration diagram (page 14)
Fig. 9 · MAC Spoofing Configuration

WAN MAC Address (Spoofed):

This is only available when devices are under the router mode. The spoofed MAC address to be used by the device’s WAN interfaces, the Ethernet address of the outgoing packets from the WAN interface would be replaced with this address. If blank, the WAN interfaces will use the value of MAC.

Page 15 of the LevelOne 4100 user manual — 6. LAN
Page 15 · click to enlarge
Page 15

6. LAN

LAN Configuration

LevelOne 4100 — 6. LAN diagram (page 15)
Fig. 10
1. Under “ Network Settings ”, you enter the IP address and subnet mask of your network.
2. Multicast Limits: Broadcast Limit: the value specifies the maximum limit on the percentage of

broadcast packets, which will be bridged to the destination interface (as a percentage of the source side bandwidth)

Multicast Limitthe value specifies the maximum limit on the percentage of

multicast packets, which will be bridged to the destination interface (as a percentage of the source side bandwidth)

Page 16 of the LevelOne 4100 user manual — DHCP Server Configuration
Page 16 · click to enlarge
Page 16

DHCP Server Configuration

LevelOne 4100 — DHCP Server Configuration diagram (page 16)
Fig. 11 · DHCP Server Configuration

These configuration parameters are for the device’s internal DHCP server.

1. Server Setting: “Yes” or “No”, to enable/disable DHCP
Client IP Address RangeMinimum and Maximum limit on the DHCP IP
2. Client Network Information Domain Name: LAN domain name provided to DHCP clients during the

OFFER process.

DNS ServerThis statically assigned DNS server IP address will be

provided to clients during the OFFER process.

3. Static Address Assignment Up to eight static DHCP address assignments can be configured. To add a

static IP assignment, enter the LAN device’s host name (must be unique in the private network) and/or MAC address. Specify the Internal address to be assigned and press the "Add" button.

address pool

Page 17 of the LevelOne 4100 user manual — Router Configuration
Page 17 · click to enlarge
Page 17

Router Configuration

LevelOne 4100 — Router Configuration diagram (page 17)
Fig. 12 · Router Configuration

These configuration parameters are for the device’s internal router.

1. Dynamic Routing: Whether or not dynamic routing on TX/RX interfaces is enabled/disabled.
2. Static Routing Under “ Static Routing ”, you can specify the routing path of your internal network.
Page 18 of the LevelOne 4100 user manual — Port Forwarding Configuration
Page 18 · click to enlarge
Page 18

Port Forwarding Configuration

LevelOne 4100 — Port Forwarding Configuration diagram (page 18)
Fig. 13 · Port Forwarding Configuration
1. Under “ Reserved Ports ”, specified are the ports, which cannot be forwarded to the LAN.
2. Under “ Port Forwarding to LAN ”, you enter the specifications, which you will be forwarding to the LAN, including port range , protocol (Both, TCP or UDP), and destination IP address .

Click on “Save NAPT Settings” to save your configurations.

Page 19 of the LevelOne 4100 user manual — 7. SIP
Page 19 · click to enlarge
Page 19

7. SIP

SIP Configuration

LevelOne 4100 — 7. SIP diagram (page 19)
Fig. 14
1. Under “ SIP Server Settings ”, you enter the server address , port , domain name , and expiration time unit, if you choose to send a registration request with an expiration time.
2. Gateway Settings
  • Dial Plan: refer to appendix A of this guide
  • # use as a quick dial function: If this box is checked, the dialed digits would be sent out when the ‘#’ key is pressed.
  • Enable # to be recognized as dial number: allow the ‘#’ key to appear in the INVITE request URI
  • Enable * to be recognized as dial number: allow the ‘*’ key to appear in the INVITE request URI
  • For the line on the endpoint, enter the Line Phone Number , Caller-ID Name , signalling port value , authentication Username and Password , and select if AEC is to be performed on this line. The default settings are compatible with FWD settings. If you`d like to know more about FWD, please visit http:// <a href="http://www.freeworlddialup.com" rel="nofollow noopener" target="_blank">www.freeworlddialup.com</a> .
Page 20 of the LevelOne 4100 user manual — SIP Extensions
Page 20 · click to enlarge
Page 20

SIP Extensions

LevelOne 4100 — SIP Extensions diagram (page 20)
Fig. 15 · SIP Extensions
1. Support PRACK method: enable SIP PRACK support. 2. Encode SIP URI with user parameter: encode user=phone parameter in SIP URI.
3. Send INVITE with Timer header: encode Timer header in all INVITE requests for ringing timeout
4. SIP session timer: enable SIP session timer function. 5. Conditional Call Forwarding Timer: Forward the call to the pre-configured number if the phone does not pick up within the timer.
6. Disable Call Waiting: disable the call waiting tone. 7. Disable Caller-ID display: disable the caller-id display of incoming calls. 8. Call Hold using C=0.0.0.0: using the call hold method described in RFC2543. If unchecked, the call hold would follow RFC3263 method
9. Send NOTIFY: send out NOTIFY request to transferor for unattended and attended call transfer.
Page 21 of the LevelOne 4100 user manual — RTP Telephone Event Configuration
Page 21 · click to enlarge
Page 21

RTP Telephone Event Configuration

LevelOne 4100 — RTP Telephone Event Configuration diagram (page 21)
Fig. 16 · RTP Telephone Event Configuration

This sub-page allows configuration of the out-of-band signalling options for SIP. Select whether OOB telephone event signalling is to be done using the SIP INFO message, or to be done via RFC2833 RTP signalling. For additional information please refer to the RFC2833.

Page 22 of the LevelOne 4100 user manual — ToS/DiffServ
Page 22 · click to enlarge
Page 22

ToS/DiffServ

LevelOne 4100 — ToS/DiffServ diagram (page 22)
Fig. 17 · ToS/DiffServ

This sub-page is used to configure the Type-of-Service/Diffserv byte values, which are to be used in the IP header of all transmitted SIP signalling packets and RTP packets. The ToS/DiffServ byte values are entered as two-digit hexadecimal values. If no special ToS/DiffServ value is to be used for a particular traffic type, enter “00” or leave the setting empty.

Press “Save ToS/DiffServ Settings” to save these new settings.

Page 23 of the LevelOne 4100 user manual — 8. CODEC
Page 23 · click to enlarge
Page 23

8. CODEC

Audio/CODEC Configuration

LevelOne 4100 — 8. CODEC diagram (page 23)
Fig. 18
1. CODECS: configure the silence suppression to your desired settings.
2. Packetization: configure the packet sending increments.
3. Jitter Buffer: configure the timing of the voice buffering. Selection between adaptive or fixed jitter buffer. Default = ADAPTIVE Set the adaptive jitter buffer maximum playout delay. Default = 100ms or Fixed jitter buffer playout delay. Default = 40ms Whether or not to automatically switch from an adaptive jitter buffer to a fixed jitter buffer upon fax/modem tone detection

Click on “Save CODEC Configuration” to save the configurations made.

Page 24 of the LevelOne 4100 user manual — 9. SYSTEM
Page 24 · click to enlarge
Page 24

9. SYSTEM

Set Security Password

LevelOne 4100 — 9. SYSTEM diagram (page 24)
Fig. 19

Configure a password for the system.

Page 25 of the LevelOne 4100 user manual — AutoUpdate
Page 25 · click to enlarge
Page 25

AutoUpdate

LevelOne 4100 — AutoUpdate diagram (page 25)
Fig. 20 · AutoUpdate

Enable an AutoUpdate function, if your want to update your IAD firmware/configuration by your update server.

Enter your update server IP, IAD will execute auto update after reboot automatically.

Page 26 of the LevelOne 4100 user manual — Localization
Page 26 · click to enlarge
Page 26

Localization

LevelOne 4100 — Localization diagram (page 26)
Fig. 21 · Localization

Choose the correct country for a proper impedance match, as well as the NTP

Server, and Time Zone. Check the “Adjust clock for daylight savings”, when applicable.

Click on “Save Localization Settings”, to save your configurations.

Page 27 of the LevelOne 4100 user manual — Gain Control
Page 27 · click to enlarge
Page 27

Gain Control

LevelOne 4100 — Gain Control diagram (page 27)
Fig. 22 · Gain Control

Audio Input/Output Gain Configuration: You can adjust the FXS port input/output audio gain level with this configuration.

Page 28 of the LevelOne 4100 user manual — Caller ID
Page 28 · click to enlarge
Page 28

Caller ID

LevelOne 4100 — Caller ID diagram (page 28)
Fig. 23 · Caller ID

Select the format of Caller ID to match your phone set CID type.

Page 29 of the LevelOne 4100 user manual — Service Access Configuration
Page 29 · click to enlarge
Page 29

Service Access Configuration

LevelOne 4100 — Service Access Configuration diagram (page 29)
Fig. 24 · Service Access Configuration

Check the proper boxes enabling LAN and WAN for the HTTP access.

Click on “Save Service Access Settings”, to save the configurations.

Page 30 of the LevelOne 4100 user manual — 10. Download
Page 30 · click to enlarge
Page 30

10. Download

LevelOne 4100 — 10. Download diagram (page 30)
Fig. 25 · 10. Download

For both HTTP and TFTP methods, the device will reboot itself into downloader mode if the main application is being executed, and proceed with the ROM file download and permanent write of the application to the device’s flash memory. After the download is completed, the download status page will be displayed.

Page 31 of the LevelOne 4100 user manual — 11. Logout
Page 31 · click to enlarge
Page 31

11. Logout

LevelOne 4100 — 11. Logout diagram (page 31)
Fig. 26 · 11. Logout

Click Logout to Logout the system configuration

Page 32 of the LevelOne 4100 user manual — 12. Reboot
Page 32 · click to enlarge
Page 32

12. Reboot

LevelOne 4100 — 12. Reboot diagram (page 32)
Fig. 27 · 12. Reboot

Choose the “Reboot and execute Main Application” option, for execution of the main application which you have configured, once you reboot the system.

Choose the “Reboot and execute Downloader Application” option, to begin downloading, once you reboot the system.

Page 33 of the LevelOne 4100 user manual — Appendix A. Dial Plans
Page 33 · click to enlarge
Page 33

Appendix A. Dial Plans

The SIP code will allow provisioning (via web browser) of the dial plan. A dial plan gives the unit a map to determine when a complete number has been entered and should be passed to the gatekeeper for resolution into an IP address. Dial plans are expressed using the same syntax as used by MGCP NCS specification. The formal syntax of the dial plan is described in the following notation: Digit ::= "0" | "1" | "2" | "3" | "4" | "5" | "6" | "7" | "8" | "9" Timer ::= "T" | "t" Letter ::= Digit | Timer | "#" | "*" | "A" | "a" | "B" | "b" | "C" | "c"| "D" | "d" Range ::= "X" | "x" -- matches any digit | "[" Letters "]" -- matches any of the specified letters Letters::= Subrange | Subrange Letters Subrange::= Letter -- matches the specified letter | Digit "-" Digit -- matches any digit between first and last Position::= Letter | Range StringElement::= Position -- matches any occurrence of the position | Position "." -- matches an arbitrary number of occurrences including 0 String ::= StringElement | StringElement String StringList::= String | String "|" StringList DialPlan::= String | "(" StringList ")" A dial plan, according to this syntax, is defined either by a (case insensitive) string or by a list of strings. Regardless of the above syntax, a timer is only allowed if it appears in the last position in a string (12T3 is not valid). Each string is an alternate numbering scheme. The unit will process the dial plan by comparing the current dial string against the dial plan. If the result is under-qualified (partial matches at least one entry), then it will do nothing further. If the result matches or is over-qualified (no further digits could possibly produce a match), then it sends the string to the gatekeeper and clear the dial string. The Timer T is activated when it has all that is required to produce a match. The period of timer T is 4 seconds. For example, a dial plan of (xxxT|xxxxx) will match immediately if 5 digits are entered. It will also match after a 4 second pause when 3 digits are entered.

Page 34 of the LevelOne 4100 user manual — Sample Dial Plans
Page 34 · click to enlarge
Page 34

Sample Dial Plans

Simple Dial Plan Allows the dialing of 7 digit numbers (e.g. 5551234) or an operator on 0. Dial plan is (0T|xxxxxxx)

Non-dialed Line Dial Plan As soon as the handset is lifted, the unit contacts the gatekeeper (used for systems where dtmf detection is done in-call). Dial plan is (x.) i.e. match against 0 (or more) digits. Note: the dot ‘.’

Complex Dial Plan Local operator on 0, long distance operator on 00, four digit local extension number starting with 3,4 or 5, seven digit local numbers are prefixed by an 8, two digit star services (e.g. 69), ten digit long distance prefixed by 91, and international numbers starting with 9011+variable number of digits. The dial plan for this is: (0T|00T|[3-5]xxx|8xxxxxxx|*xx|91xxxxxxxxxx|9011x.T)

Page 35 of the LevelOne 4100 user manual — Appendix B. FXO Settings
Page 35 · click to enlarge
Page 35

Appendix B. FXO Settings

One-Step Dialing

LevelOne 4100 — Appendix B. FXO Settings diagram (page 35)
Fig. 28 · Appendix B. FXO Settings

One-Step Dialing It can make a direct dialing from remote via IP network, IAD and PSTN network to final PSTN destination. It is like a PLAR function.

To make this function available: mark the Enable One-Step Dialing box and enter your final PSTN destination number in Dial Number field.

Page 36 of the LevelOne 4100 user manual — FXO Setting
Page 36 · click to enlarge
Page 36

FXO Setting

LevelOne 4100 — FXO Setting diagram (page 36)
Fig. 29 · FXO Setting

Line Side Impedance Setting: To specify the PSTN or PBX impedance, choose your country from the list.

For most of the cases, once you choose your country, all the other corresponding settings will be set automatically. Or please enter the right impedance if you cannot find your country in the list.

For example: if the PSTN line impedance is 600 ohm, please select 600 in this field. If you choose your country from the list, go directly to Loop Current Shutdown Detection setting.

If your country is not in the above setting list or your country is in the list but you still encounter a disconnection failure, you must do “Tone Detection Frequency Setting” and “Tone On-Off Duration Setting”. Tone Detection Frequency Setting:

Page 37 of the LevelOne 4100 user manual — FXO Setting
Page 37 · click to enlarge
Page 37

Configure the frequencies of disconnect tone. It is used to detect the incoming disconnect tone by FXO port. Due to the disconnect tone is usually composed by two different frequencies, you must get these frequencies from your local telecom standards. Key the

frequencies by Hz in Frequency1 and Frequency2 fields.

Tone On-Off Duration Setting: Configure the cadence of disconnect tone. It is used to detect the incoming disconnect tone duration by FXO port. If you know each duration value, turn CP Tone Auto Learning off. And,

Key the time of tone on duration in Tone-On field. Key the time of tone off duration in Tone-Off field. If you do not know each duration value, enable CP Tone Auto Learning. And, Save FXO settings. Reboot the system. Make a call through FXO port. After the callee reply and disconnect, wait for 10 seconds. Enter the FXO setting user interface again. You will find the Tone On-Off fields filled by values detected. Turn CP Tone Auto Learning off.

Loop Current Shutdown Detection: Select “YES” if you want to detect the status of loop current in FXO port. If not, select “NO”.

FXO Gain Control: These fields are used to decrease or increase the gains in FXO output and input channels. Default gain values are all “zero”. When you make a call from IP to PSTN, adjust FXO Input Gain Control (To PSTN) to a lower value if PSTN cannot recognize your numbers dialed after hearing the PSTN dial tone. For example, set “-6” to replace the default “0”. Always use “6” as a unit for your first trial and find a best suitable number then. When you make a call from PSTN to IP, adjust FXO Output Gain Control (To IP) to a lower value if IP cannot recognize your numbers dialed after hearing the dial tone. For example, set “-6” to replace the default “0”.

Click Save FXO Setting to save all settings to FXO port.

Page 38 of the LevelOne 4100 user manual — FXO Setting
Page 38 · click to enlarge
Page 38

For further FXO settings, please contact with your local ISP or visit www.level1.com for further product information.

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the LevelOne 4100

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LevelOne 4100

Be the first to ask — other owners or our team will answer.

Original document

LevelOne 4100 manual PDF

38 pages·1004 KB·Stereo System·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…