Instruction/ maintenance manual of the product 5391 Lenovo
Go to page of 70
ThinkCentr e User Guide Machine T ypes: 3026, 3039, 3137, 3149, 3245, 3269, 3319, 3394, 3491, 3627, 5391, 5472, 5485, 5536, 5548, 5567, 5864, and 6213.
.
ThinkCentr e User Guide Machine T ypes: 3026, 3039, 3137, 3149, 3245, 3269, 3319, 3394, 3491, 3627, 5391, 5472, 5485, 5536, 5548, 5567, 5864, and 6213.
Note Before using this information and the pr oduct it supports, be sur e to read and understand the ThinkCentre Safety and Warranty Guide and Appendix A “Notices” on page 55 .
Contents Important safety information . . . . . vii Chapter 1. Product overview . . . . . . 1 F eatures . . . . . . . . . . . . . . . . . . 1 Specications . . . . . . . . . . . . . . . . 3 Software overview . . . . . . . . . . . . . . 4 Software provided by Lenovo .
Online Books folder . . . . . . . . . . . 51 Lenovo ThinkV antage T ools . . . . . . . . 51 ThinkV antage P roductivity Center . . . . . 51 Lenovo W elcome . . . . . . . . . . . . 52 Access Help . . . . . . . . . . . . . . 52 Safety and W arranty . . .
Important safety information CA UTION: Before using this manual, be sure to read and understand all the r elated safety information for this product. Refer to the ThinkCentre Safety and Warranty Guide that you r eceived with this product for the latest safety information.
viii ThinkCentre User Guide.
Chapter 1. P roduct overview This chapter describes the computer featur es, specications, pr einstalled software pr ograms, and part and connector locations. F eatur es This section provides information about the computer features. System information The following information covers a variety of models.
• Ability to st ore power -on self-t est (POST) har dware t est r esults • Automatic power -on startup • Desktop Management Int erface (DMI) • Intel Active Management T echnology (AMT) (availa.
• P ower-on password (POP) and Administr ator P assword for BIOS access • Startup sequence contr ol • Startup without keyboard or mouse • Support for an int egrated cable lock (K ensington loc.
Dimensions Width: 317 mm (12.48 inches) Height: 99 mm (3.9 inches) Depth: 355 mm (13.98 inches) Weight Maximum conguration as shipped: 7.5 kg (16.53 lbs) Environment • Air temperatur e: Operating.
Note: The L enovo ThinkV antage T ools pr ogram is only available on comput ers with the Windows 7 operating system fr om Lenovo. ThinkV antage Pr oductivity Center The ThinkV antage Pr oductivity Center pr ogram guides you t o a host of information and tools to help you set up, understand, maintain, and enhance your comput er .
Lenovo ThinkV antage T oolbo x The L enovo ThinkV antage T oolbo x pr ogram helps you maintain your computer , impr ove computing security, diagnose computer problems, get familiar with the innovative technologies pr ovided by L enovo, and get more information about your computer .
Locating connectors on the rear of your computer Rear connect or locations shows the locations of the connectors on the rear of your computer . Some connectors on the rear of your computer ar e color -coded to help you determine where t o connect the cables on your computer .
Connector Description DisplayP ort connector Used t o attach a high-performance monit or , a dir ect-drive monitor , or other devices that use a DisplayP ort connector . Ethernet connector Used to attach an E thernet cable for a local area network (LAN).
1 Hard disk drive (installed in some models) 5 Optical drive 2 Heat sink 6 Memory module 3 Internal speaker (installed in some models) 7 P ower supply assembly 4 Syst em fan assembly Locating parts on the system board Figure 4 “System board part locations” on page 9 shows the locations of the parts on the syst em boar d.
Locating int ernal drives Internal drives ar e devices that your computer uses to r ead and stor e data. Y ou can add drives to your computer to increase st orage capacity and enable your computer to r ead other types of media. Y our computer comes with the following factory-installed drives: • A 3.
Chapter 2. Installing or r eplacing har dware This chapt er provides instructions on how t o install or r eplace hardwar e for your comput er . Handling static-sensitive devices Do not open the static-prot ective package containing the new part until the defective part has been removed from the computer and you are ready to install the new part.
Opening the computer cover Attention: Do not open your computer or att empt any r epair befor e reading and understanding the “Important safety information” in the ThinkCentre Safety and W arranty Guide that came with your computer . T o obtain a copy of the ThinkCentre Safety and Warranty Guide , go t o: http://www.
Notes: a. Make sur e you note the locations of any cables that you disconnect from the drives or the syst em board. b. Make sur e the hard disk drive assembly is in the latched down position before closing the computer cover to prevent damage to the har d disk drive.
5. Remove any parts that might pr event access to the memory slots. 6. Open the r etaining clips. Figure 8. Opening the retaining clips If you are r eplacing an old memory module, open the r etaining clips and gently pull the memory module out of the memory slot.
Figure 10. Installing a memory module What to do next: • T o work with another piece of har dware, go to the appropriat e section. • T o complet e the installation or r eplacement, go to “Completing the parts replacement” on page 32.
Figure 11. Removing a PCI card Notes: a. The car d ts tightly int o the card slot. If necessary, alt ernate moving each side of the car d a small amount until it is removed fr om the car d slot. b. If the card is held in place by a r etaining latch, press the car d r etaining latch 1 as shown t o disengage the latch.
Figure 12. Installing the PCI card What to do next: • T o work with another piece of har dware, go to the appropriat e section. • T o complet e the installation or r eplacement, go to “Completing the parts replacement” on page 32.
Figure 13. Removing the old battery 5. Install a new batt ery . Figure 14. Installing a new batt ery 6. Close the comput er cover and connect the cables. See “Completing the parts r eplacement” on page 32. Note: When the computer is turned on for the rst time after replacing the batt ery, an error message might be displayed.
5. Push the release butt on 1 of the hard disk drive brack et as shown and then lift the hard disk drive brack et up fr om the heat sink. Figure 15. Removing the hard disk drive 6. Disconnect the signal cable and the power cable fr om the hard disk drive to completely remove the har d disk drive from the chassis.
10. Insert the two r etaining clips 1 of the har d disk drive br acket int o the corr esponding holes in the chassis, and then pivot the har d disk drive and brack et downwards until the har d disk drive br acket snaps into position. Figure 17. Installing the hard disk drive 11.
Figure 18. Removing the old optical drive 6. Install the optical drive r etainer on the side of the new optical drive. Figure 19. Installing the optical drive retainer 7. Slide the new optical drive into the drive bay until it snaps into position. Chapter 2 .
Figure 20. Installing a new optical drive 8. Connect the signal cable and the power cable t o the r ear of the optical drive. What to do next: • T o work with another piece of har dware, go to the appropriat e section. • T o complet e the installation or r eplacement, go to “Completing the parts replacement” on page 32.
3 4 5 6 7 8 Figure 21. Removing the retaining screws for the power supply assembly 4. Open the comput er cover . See “Opening the comput er cover” on page 12. 5. Pivot the optical drive bay assembly upward to gain access t o the power supply assembly .
7. Release the power supply assembly cables from the cable clips and ties in the chassis. 8. Slide the power supply assembly to the fr ont of the computer and then lift it out of the chassis.
CA UTION: The heat sink might be very hot. T urn off the computer and wait three to ve minutes to let the computer cool before opening the computer cover . T o r eplace the heat sink, do the following: 1. T urn off the comput er and disconnect all power cor ds from electrical outlets.
Replacing the front audio and USB assembly Attention: Do not open your computer or att empt any r epair befor e reading and understanding the “Important safety information” in the ThinkCentre Safety and W arranty Guide that came with your computer .
10. Reconnect the front audio and USB assembly cables to the front audio connector and the fr ont USB connector on the system boar d. See “L ocating parts on the syst em board” on page 9. What to do next: • T o work with another piece of har dware, go to the appropriat e section.
Figure 27. Removing the system fan 8. Align the four tabs on the bott om of the new syst em fan with the corresponding holes in the chassis, and push the new syst em fan straight down until it snaps into position. 9. Connect the system fan cable to the micropr ocessor fan connector on the system board.
1. T urn off the comput er and disconnect all power cor ds from electrical outlets. 2. Open the comput er cover . See “Opening the comput er cover” on page 12. 3. Remove the front bez el by releasing the three plastic tabs and pivoting the front bez el outwar d.
Figure 29. Removing the internal speaker 8. Remove the attached thermal sensor cable from the old int ernal speaker and install it on the new internal speaker .
Figure 30. Installing the new int ernal speaker 10. Reconnect the int ernal speaker cable and the thermal sensor cable to the system boar d. See “Locating parts on the syst em boar d” on page 9.
4. Connect a new keyboar d or mouse t o one of the USB connectors on the computer . Depending on where you want to connect the new keyboard or mouse, see “L ocating connectors on the front of your computer” on page 6 or “Locating connectors on the rear of your computer” on page 7.
Figure 32. Cable routing 4. Lower the optical drive bay assembly . 5. Close the comput er cover . 6. If there is an int egrat ed cable lock available, lock the computer . 7. Reconnect the ext ernal cables and power cords to the comput er . See “L ocating connect ors on the r ear of your computer” on page 7.
3 4 5 6 7 8 Figure 33. Integrated cable lock P assword protection T o deter unauthorized use of your computer , you can use the Setup Utility pr ogram to set a password. When you turn on your computer , you ar e prompt ed to type the password. The computer cannot be used until a valid password is typed in.
Chapter 3. Recover y information This chapter provides information about the r ecovery solutions provided by L enovo. This chapt er contains the following t opics: • Creating and using recovery medi.
Using recovery media This section provides instructions on how to use r ecovery media on differ ent oper ating syst ems. On the Windows 7 oper ating system and the Windows Vista oper ating system, you can use recovery media to rest ore the computer to the factory default settings only .
2. In the Rescue and Recovery main window , click the Launch advanced Rescue and Recovery arrow . 3. Click Back up your hard drive and select backup operation options.
• Restor e your hard disk drive to the fact ory default settings The Rescue and Recovery workspace enables you to rest ore the complete cont ents of your hard disk drive t o the factory default settings.
• T o cr eate a rescue medium on the Windows 7 oper ating syst em, do the following: 1. F rom the Windows deskt op, click Start ➙ All Pr ograms ➙ Lenovo ThinkV antage T ools ➙ Enhanced Backup and Restore . The Rescue and Recovery pr ogram opens.
2. Use Windows Explorer or My Comput er to display the dir ectory structure of your har d disk drive. 3. Go to the C:SWTOOLS dir ectory . 4. Open the DRIVERS folder . Within the DRIVERS folder , there ar e sever al subfolders named for various devices installed in your computer , such as AUDIO or VIDEO .
Chapter 4. Using the Setup Utility The Setup Utility pr ogram is used to view and change the conguration settings of your comput er , regar dless of which oper ating syst em you are using. However , the operating syst em settings might override any similar settings in the Setup Utility progr am.
• Not be your name or your user name • Not be a common word or a common name • Be signicantly different fr om your pr evious passwor ds P ower-On P assword When a P ower-On P assword is set, you are prompted to type a valid passwor d each time the computer is turned on.
2. F rom the Setup Utility pr ogram main menu, select Devices . 3. Depending on the device you want to enable or disable, do one of the following: • Select USB Setup to enable or disable a USB device. • Select A T A Drive Setup to enable or disable an internal or ext ernal SA T A device.
44 ThinkCentre User Guide.
Chapter 5. Updating system progr ams This chapter provides information about updating the POS T and BIOS, and how to recover fr om a POS T and BIOS updat e failure. Using system progr ams System pr ograms are the basic layer of software built into your computer .
Updating (ashing) the BIOS from your operating system Note: Because L enovo makes constant impr ovements t o its Web sites, the W eb page contents ar e subject to change without notice, including the contents r eferenced in the following pr ocedure.
Chapter 6. T r oubleshooting and diagnostics This chapter describes some basic tr oubleshooting and diagnostic progr ams. If your computer pr oblem is not described here, see Chapter 7 “Getting information, help, and service” on page 51 for additional troubleshooting resour ces.
Symptom Action The operating system does not start. V erify that: • The startup sequence includes the device wher e the oper ating system resides. Usually, the oper ating system is on the har d disk drive. F or mor e information, see “Selecting a startup device” on page 43 .
PC-Doctor for Rescue and Recovery The PC-Doctor for Rescue and Recovery diagnostic progr am is part of the Rescue and Recovery workspace on each Lenovo comput er . Use the PC-Doctor for Rescue and Recovery diagnostic pr ogram if you are unable t o start the Windows oper ating system.
Note: Y ou can insert the disc into the optical drive when you ar e setting the startup device sequence. However , if you insert the disc int o the optical drive when you have alr eady entered the oper ating system, you need to restart the comput er to access the diagnostic progr am.
Chapter 7. Getting information, help, and ser vice This chapt er contains information about help, service, and technical assistance for products manufactured by Lenovo. Information resources Y ou can use the information in this section to access useful r esources relating t o your computing needs.
• Pr oduct Recovery • Rescue and Recovery • System Updat e Note: The ThinkV antage P roductivity Cent er progr am is only available on computers that have an internal hard disk drive, a pr einstalled Windows Vista oper ating system, and preinstalled software pr ograms from Lenovo.
• Access troubleshooting and support information for your computer model and other supported pr oducts. • Find the service and support phone numbers for your country or region. • Find a Service Pr ovider located near you. Help and service This section contains information about obtaining help and service.
Note: Phone numbers are subject to change without notice. If the number for your country or r egion is not provided, contact your Lenovo reseller or Lenovo mark eting repr esentative.
Appendix A. Notices Lenovo may not offer the pr oducts, services, or features discussed in this document in all countries. Consult your local L enovo repr esentative for information on the pr oducts and services curr ently available in your area.
T elevision output notice The following notice applies to models that have the fact ory-installed television-output feature. This product incorpor ates copyright prot ection t echnology that is pr otected by method claims of certain U .S. patents and other int ellectual property rights owned by Macrovision Corpor ation and other rights owners.
Inde x A a rescue medium, creating and using 38 Administrat or, password 42 antivirus softwar e 6 audio line-in connector 7 audio line-out connector 7 audio subsystem 1 B backup and r ecovery oper ati.
internal speaker , replacing 28 K keyboard connector 8 keyboard, r eplacing 31 L Lenovo ThinkV antage T oolbox 48 Lenovo ThinkV antage T ools 51 Lenovo Web sit e 52 Lenovo Welcome 5, 52 locating compo.
starting the Setup Utility progr am 41 startup device 43 sequence, changing 43 tempor ary, selecting 43 static-sensitive devices, handling 11 system management 1 progr ams 45 system boar d components,.
60 ThinkCentre User Guide.
.
Part Number: 71Y7175 Printed in USA (1P) P/N: 71Y7175 *71Y7175*.
An important point after buying a device Lenovo 5391 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lenovo 5391 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lenovo 5391 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lenovo 5391 you will learn all the available features of the product, as well as information on its operation. The information that you get Lenovo 5391 will certainly help you make a decision on the purchase.
If you already are a holder of Lenovo 5391, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lenovo 5391.
However, one of the most important roles played by the user manual is to help in solving problems with Lenovo 5391. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lenovo 5391 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
