Instruction/ maintenance manual of the product 506033-35 Lennox Hearth
Go to page of 8
1 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. FREEST ANDING BLOWER SNAP SWITCH RETROFIT KIT COUNTRY COLLECTION™ WOODSTOVES P/N 506033-35 Rev . NC, 11/2009 HEARTH PRODUCTS KITS AND ACCESSORIES KIT CONTENTS 1 ea. Blower Wire Harness (item #1) 1 ea.
2 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Figure 2 Stove Back Blower INSTALLATION INSTRUCTIONS Removing Existing Blower From Stove Step 1. UNPLUG POWER CORD AND ENSURE APPLIANCE IS COLD Step 2. Using a 5/32 allen wrench/T -handle, remove the blower mounting allen screws from blower , and remove blower from stove.
3 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Figure 7 Step 8. Slide the supplied 6” of 3/4” heat shrink tube over the (3) blower harness wires.
4 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Step 3. Insert snap switch bracket mounting tabs between the pedestal and the firebox bottom. See Figure 17 . Figure 16 St ep 2. Insert a large flat head screwdriver or pry bar into the small open- ing between the pedestal mounting flange and the bottom firebox of the stove.
5 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Step 4. Whil e ho ld ing th e sn ap s wit ch bra ck et a gai ns t th e pe de sta l, sli de th e br ac ke t to wa rds th e r ear of th e s tov e u nt il i t c om es t o a st op.
6 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. WOODSTOVES WITH LEG BASE Step 1. Using a 9/16” wrench or socket loosen the left heat shield bolt. This bolt is located on the bottom side of the leg heatshield as shown. See Figure 26 . Figure 26 Step 2.
7 St ep 7 . Plug the power cord into grounded 120 V AC receptacle. Do not route the power cord under the stove or allow it to come in contact with any surface of the stove. Step 5. Plug the blower harness into plug on rear of snap switch bracket. See Figure 32 .
8 Printed in U.S.A. © 2009 Lennox Hearth Products P/N 506033-35 Rev . NC 11/2009 Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
An important point after buying a device Lennox Hearth 506033-35 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lennox Hearth 506033-35 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lennox Hearth 506033-35 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lennox Hearth 506033-35 you will learn all the available features of the product, as well as information on its operation. The information that you get Lennox Hearth 506033-35 will certainly help you make a decision on the purchase.
If you already are a holder of Lennox Hearth 506033-35, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lennox Hearth 506033-35.
However, one of the most important roles played by the user manual is to help in solving problems with Lennox Hearth 506033-35. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lennox Hearth 506033-35 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
