EN
Lathem logo
Official user manual

Lathem PC100

21 pages·133 KB·Time Clock·PDF·ENDEFRITNLJA
Lathem PC100
Table of Contents 28 sections Installation & · PC100 Terminal · User’s Guide · Contents · … ShowHide
Page 1 of the Lathem PC100 user manual — PC100 Terminal
Page 1 · click to enlarge
Page 1

Installation &

PC100 Terminal

User’s Guide

Page 2 of the Lathem PC100 user manual — Installation &
Page 2 · click to enlarge
Page 2

PayClock, Lathem and the Lathem logo are registered trademarks of Lathem Time Corporation. Other product names mentioned in

equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructional manual, may cause harmful interference to radio communications. Operation of this

Shielded cables must be used with this unit to ensure compliance with the Class A FCC limits

this manual may be trademarks of their respective companies and are hereby acknowledged.

authority to operate the equipment.

at his or her own expense.

Page 3 of the Lathem PC100 user manual — Installation &
Page 3 · click to enlarge
Page 3

Lathem warrants the hardware products described in this guide against defects in material and workmanship for a

period of one year from date of original purchase from Lathem or from an authorized Lathem reseller. The conditions

of this warranty and the extent of the responsibility of Lathem Time Corporation (“Lathem”) under this warranty are

2. This warranty does not apply to any product which has been subject to abuse, neglect, or accident, or which has
6. WARRANTY DISCLAIMER AND LIMITATION OF LIABILITY: Except only the limited express warranty

deemed to have failed of its essential purpose, Lathem's maximum liability shall be to refund the purchase price

7. Proof of date of purchase from Lathem or an authorized Lathem reseller is required for warranty service on this
1. This warranty will become void when service performed by anyone other than an approved Lathem warranty
4. The sole responsibility of Lathem under this warranty shall be limited to repair of this product, or replacement

reseller and any such products are purchased "as is, with all faults." In no event will Lathem be liable for any

direct, indirect, special, incidental or consequential damages arising out of or in connection with the delivery,

8. This Warranty grants specific legal rights. Additional legal rights, which may vary by locale, may also apply.

had the serial number altered or removed, or which has been connected, installed, adjusted, or repaired other

5. If it becomes necessary to send the product or any defective part to Lathem or any authorized service dealer,

the product must be shipped in its original carton or equivalent, fully insured with shipping charges prepaid.

use or inability to use, or performance of this product. In the event any limited remedy given herein shall be

3. This warranty does not cover dealer labor cost for removing and reinstalling the machine for repair, or any

set forth above, the products are sold with no expressed or implied warranties of any kind, and the implied

warranties are given with respect to products purchased other than from Lathem or an authorized Lathem

warranties of merchantability and fitness for a particular purpose are hereby expressly disclaimed. No

9. Should any difficulties arise with the performance of this product during warranty, or with any Lathem

Lathem will not assume any responsibility for any loss or damage incurred in shipping.

Copyright © 2003 Lathem Time Corporation. All rights reserved.

Limited One-Year Limited Warranty

200 Selig Drive, SW, Atlanta, GA 30336 404-691-0405

authorized service centers, contact Lathem Time at the address below.

Document numberUSG0038C

www.lathem.com

expendable parts that are readily replaced due to normal use.

than in accordance with instructions furnished by Lathem.

service dealer results in damage to the product.

thereof, at the sole discretion of Lathem.

upon return of the product.

product.

listed below.

Lathem Time · 08-04-2006

Page 4 of the Lathem PC100 user manual — Installation &
Page 4 · click to enlarge
Page 4
Page 4 of the Lathem PC100 user manual — Installation &
Page 7 of the Lathem PC100 user manual — C H A P T E R 1
Page 7 · click to enlarge
Page 7

With the PC100 terminal, employees use their plastic ID badges to punch in and out –

it’s that simple. Using Lathem software and your computer, the PayClock terminal is

Reliability, functionality and ease of use are trademarks of the PayClock terminal.

the perfect solution for businesses that want to track employee time and automate

The PC100 terminal package includes the following:

  • PC100 Terminal
  • AC Wall Adapter – 115 VAC 60 HZ
  • Mounting Bracket
  • 3 Mounting Screws and Anchors 2 Keys

Welcome

C H A P T E R 1

payroll.

Page 8 of the Lathem PC100 user manual — C H A P T E R 2
Page 8 · click to enlarge
Page 8

Check your package contents to make sure everything is accounted for before

starting. Decide where to mount your clock. Keep in mind that the AC adapter

Lathem PC100 — Mounting the PC100 diagram (page 8)
Fig. 1 · Mounting the PC100

» Insert each screw through the bracket into the anchors, and tighten

» Align the mounting bracket back on the wall

To mount the clock, you need the following items:

top (arrow pointing Up) is 54 inches from

» Insert an anchor into each hole, tapping it

with a hammer until it is flush against the

» Remove the bracket and drill a 5/16-inch

» Hold the bracket against the wall so the

1. Screw the mounting bracket to the wall

Mounting the PC100

» Mark the 3 holes with a pencil

hole at each mark

plugs into a wall outlet.

Drill with a 5/16” bit

C H A P T E R 2

Show 6 more labels / short text on this page
Phillips head screwdriver · the floor · securely · wall · Hammer · Pencil
Page 9 of the Lathem PC100 user manual — Mounting the PC100
Page 9 · click to enlarge
Page 9

» Turn your key counter-clockwise in the lock at the clock’s right-middle

» Align the keyholes on the back of the clock with the studs on the

» Turn the key clockwise to lock the clock onto the bracket

2. Place the clock onto the mounting bracket

» Slide the clock down onto the bracket

» Remove the key

mounting bracket · section to unlock

Page 10 of the Lathem PC100 user manual — C H A P T E R 3
Page 10 · click to enlarge
Page 10

terminals. The PC2500 modular port is set up to use with the PC400 terminals

When selecting your installation method, the type of wire that will be used is

using J-Kits or in areas where the cable may run near a device that transmits

PC100 / PC2000 modular port is set up to use with the PC2000 and PC100-R

computer. You can connect the PayClock terminal to the computer using an

RS-232 cable or RS-485 cable. Choose the setup that best suits your needs.

than 100’ to achieve communications. Category-3 or Category-5 cable with

twisted pairs should be used for distances greater than 100’, in installations

terminal blocks to connect the PC2000, PC100-R or PC3500 terminals. The

After mounting your PayClock on the wall, you need to connect it to your

1. Turn the PayClock so its back faces you 2. Plug the power cord (AC adapter) into the PayClock, keeping the cord slack
3. Plug the other end of the power cord into a wall outlet 4. Connect the jack end of the serial cable to the PC100 5. Connect the other end of the serial cable to an open COM port on your computer. All serial ports are raised pin (male) connectors

The Swift-485+ allows you to connect PayClock terminals to the modular

(not currently available). The RS232 connection to the PC is made simple

ports and to the screw terminal blocks. You can use either of the screw

an RF frequency. Do not use J-Kits with modular wire

For details, see the Cable Wiring Diagrams appendix.

Connecting to the Computer

Connecting the PayClock via RS-232

Connecting Terminals via RS-485

using a stereo type plug in jack.

C H A P T E R 3

Page 11 of the Lathem PC100 user manual — RS485
Page 11 · click to enlarge
Page 11
1. Run Category 3 (minimum) cable from the SWIFT-485+ to a terminal or J-kit. If you connect directly to a terminal, use an RJ-45 or RJ-11

computer. You can wire the terminals directly to the SWIFT-485+ or use J-

2. Connect the AC power cord adapter to each terminal and plug the cord into a wall outlet

kits (junction boxes). Terminals can be located up to 4000 feet from the

A star network connects up to 31 terminals or sync time devices to the

RS485

Lathem PC100 — RS485 diagram (page 11)
Fig. 2
Lathem PC100 — RS485 diagram (page 11)
Fig. 3

Connecting Terminals via RS-485 (Star Configuration)

3. Repeat these steps for each terminal in the network

connector on the end that plugs into the terminal

RS485

RS232

Show 10 more labels / short text on this page
Power to · terminals · connection Use either · connection RJ11 RJ45 · Use either · to terminals · LED’s · computer · to PC · Power
Page 12 of the Lathem PC100 user manual — RS485
Page 12 · click to enlarge
Page 12

starting from the SWIFT-485+. Terminals can be located up to 4000 feet from

1. Run Category 3 (minimum) cable from the SWIFT-485+ to the first J-Kit (junction box)

For more details or how to supply AC power to the PC100-R from the SWIFT-

A multi-drop network connects up to 31 terminals or sync time devices to the

2. Use a cable (up to 4 feet long) with an RJ-11 connector on both ends, and plug one end into the J-Kit (junction box)
5. For the next terminal, run cable from the previous J-Kit (junction box) to the next J-Kit (junction box) and repeat steps 2, 3 & 4

computer. You wire the terminals to junction boxes running in a single line

4. Connect the power cord (AC adapter) to the terminal and plug the cord into a wall outlet

Connecting Terminals via RS-485 (Multi-Drop Configuration)

4. See the Cable Wiring Diagrams for detailed connection points
6. See the Cable Wiring Diagrams for detailed connection points

Max 4000 ft from SWIFT-485+ to Last Terminal

SWIFT-485+ J-Kit (junction box)

3. Plug the other RJ-11 connector to a terminal

Up to 31 Terminals

485+, see the SWIFT-485+ User’s Guide.

the computer

Page 13 of the Lathem PC100 user manual — Special Badges
Page 13 · click to enlarge
Page 13

the left side of the badge when swiping. To swipe the badge, insert it at the top of

The PC100 has a magnetic stripe badge reader. The magnetic stripe should be on

This badge displays a clock status report. The status report shows the current

The base model PC100 clock allows only an RS-232 connection. The PC100-R

model allows RS-232 or RS-485 connections; RS-485 connections require the

Three supervisor badges are available for your PC100. These badges perform

VER 1.05 | CLK READY

MEM 10% | TIME 12HR

ID# 049 | BAUD 9600

| DST ON

the reader, and then pull it down with a continuous and smooth motion.

Lathem PC100 — VER 1.05 | CLK READY diagram (page 13)
Fig. 4

Badge #251 – View Clock Status

Terminal Manager software add-on.

Using the PC100

certain tasks at the clock.

C H A P T E R 4

clock setup:

Special Badges

Page 14 of the Lathem PC100 user manual — ENTER BAUD 1ST DIGIT
Page 14 · click to enlarge
Page 14

Swipe this badge to change the baud rate – the default is 9600. You may need

prompted, swipe an employee badge that matches your desired ID. If you

ENTER BAUD 1ST DIGIT

have more than one clock, make sure each one has a unique ID number.

1200 2400 4800 9600

prompted, swipe employee badge #1, 2, 4 or 9 to indicate 1200, 2400,

Swipe this badge to change the clock ID – the default ID is 49. When

To change the baud rate, swipe the Set Baud Rate badge, then when

♦ PC100 version number ♦ Terminal ID# (ID=49) ♦ Percent full memory (each time you poll the clock, this resets to 0%)

After a few seconds, the display returns to normal.

♦ Clock ready status (READY/LOAD LIST) ♦ Baud Rate ♦ 12-Hour or 24-Hour time display format ♦ Daylight Savings Time (DST) ON/OFF

problems communicating with the clock.

These problems can result from a noisy

Badge #254 – Setup Terminal ID

to reduce the baud rate if you have

environment or a long serial cable

Badge #253 – Set Baud Rate

(usually more than 50 feet).

4800 or 9600 baud.

Page 15 of the Lathem PC100 user manual — Specifications
Page 15 · click to enlarge
Page 15
For PC100-RRS-485 Cat. 3 or Cat. 5 cable (suggested) at speeds

Casing: 6.375”W x 7.375”H x 1.5”D flame-retardant ABS plastic. 19 oz. Includes key lock and wall mounting bracket

BadgesAccepts badges #1-250. Badge metallic stripes are even-parity

Swipe “Beeper” signals good or bad badge reading and low memory.

MemoryStores about 1,500 registrations. Protected by internal 10-year

This product’s lithium battery contains Perchlorate Material –

www.dtsc.ca.gov/hazardouswaste/perchlorate for information

CertificationsUL; C-UL; FCC Part-15 Class-B; Canada ICES-003 Class-B;
Display4 lines x 20 characters liquid crystal with large block digits
PortsRS-232 cable at speeds of 1200, 2400, 4800 and 9600 baud
Power6VDC/ 300 mA wall-mount power supply. UL approved
ReaderMag-Stripe Track 2 reads standard “credit card” format
StatusGreen and red LED’s show good or bad badge swipes

special handling may apply. Please go to web site

CE-CENELEC EN55022; CENELEC EN55024

about proper methods of disposal in California.

of 2400, 4800 and 9600 baud. Up to 4000 feet

lithium battery.

Specifications

Badge

Page 16 of the Lathem PC100 user manual — RS-232 (Computer to PC100)
Page 16 · click to enlarge
Page 16
Lathem PC100 — Cable Wiring Diagrams diagram (page 16)
Fig. 5 · Cable Wiring Diagrams

Cable Wiring Diagrams

RS-232 (Computer to PC100)

A P P E N D I X A

Page 17 of the Lathem PC100 user manual — RS-485 Multi-Drop
Page 17 · click to enlarge
Page 17

Be sure to maintain polarity through out the chain

Fig. A – Junction box wiring connect points

instead of eight 8 points

See Fig. A

Some junction boxes have

RS-485 Multi-Drop

only six connect points

PayClock PayClock PayClock · 6 points

Page 18 of the Lathem PC100 user manual — Junction Box to Terminal
Page 18 · click to enlarge
Page 18

Junction Box to Terminal

Page 19 of the Lathem PC100 user manual — PC100
Page 19 · click to enlarge
Page 19

correctly. See the section on Using the

This badge may have been exposed to

something magnetic. Replace this

Make sure you swiped the badge

badge with a new one

PC100

record and the clock does not signal

When I swipe a badge, it does not

Troubleshooting

A P P E N D I X B

PC100

Description Solution · Or · any errors

Page 20 of the Lathem PC100 user manual — PC100
Page 20 · click to enlarge
Page 20
Page 20 of the Lathem PC100 user manual — PC100
Page 21 of the Lathem PC100 user manual — PC100
Page 21 · click to enlarge
Page 21
Page 21 of the Lathem PC100 user manual — PC100
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Lathem PC100

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lathem PC100

Be the first to ask — other owners or our team will answer.

Original document

Lathem PC100 manual PDF

21 pages·133 KB·Time Clock·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…