




This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense.
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS A LIMITS FOR RADIO NOISE EMISSIONS
FROM DIGITAL APPARATUS AS SET OUT IN THE RADIO INTERFERENCE REGULATIONS OF THE
CANADIAN DEPARTMENT OF COMMUNICATIONS.
LE PRÉSENT APPAREIL NUMÉRIQUE N'ÉMET PAS DE BRUITS RADIOÉLECTRIQUES DÉPASSANT LES
LIMITES APPLICABLES AUX APPAREILS NUMÉRIQUES DE CLASSE A PRESCRITES DANS LE
RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE ÉDICTÉ PAR LE MINISTÈRE DES
COMMUNICATIONS DU CANADA.
The details of this User's Manual are subject to change even without previous notification. This User's Manual has been prepared with the utmost care to cover all aspects of the time recorder's use. Be sure to use your time clock after you have fully understood the hardware and software specifications and limits. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical, photocopying, recording or otherwise.
This User's Manual and its contents are copyrighted by LATHEM TIME CORP. with all rights reserved.

(800) 241-4990

This user's manual is prepared for safe and proper use of the unit. Please follow all the instructions to avoid possible danger to yourself or others and damage to the unit.
Various warnings and cautions are provided throughout this manual along with signs. Remember each sign and its explanation listed below for your safety and proper operation of the unit.
Do not disassemble the unit. There is a high voltage present inside, possibly leading to an electric shock.
Do not modify the unit. Modifications may cause a fire and/or electric shock.
If any anomaly occurs, for example, heat or smoke is generated or an odor is emitted, unplug the unit immediately and contact your dealer for servicing. There is a danger that further use may cause a fire or electric shock.
Do not use any voltage of the power source other than designated. Do not share a single outlet with another plug. These may lead to fire or shock hazards.
Do not damage, break, or modify the power cord. Do not put a heavy object on, pull, or forcefully bend the cord, either. These may damage the cord, possibly resulting in a fire or electric shock.

If foreign matter should get in the unit (including a piece of metal, water, or liquid), disconnect the plug from the outlet immediately and contact your dealer for servicing. There is a danger that further use may cause a fire or electric shock.
Do not plug or unplug the unit with a wet hand. You may get an electric shock.
Do not place the unit on an uneven or tilted surface. This may result in injuries due to the unit dropping or falling off.
Do not put a water-filled container or a metal object on top of the unit. If water is spilled or the metallic object slips inside, a fire or shock hazard may occur.
Do not install the unit in a humid or dusty environment. It may cause a fire or electric shock.
Do not place the unit near kitchen counter or humidifier. Oil, smoke, or steam generating from them may cause fire or shock hazards.
Do not yank the power cord to disconnect from the outlet. Hold the plug with your hand to do so, or the cord may be damaged, possibly leading to a fire or electric shock.
Remove the line cord plug from the outlet before transferring the unit, or it may damage the cord, possibly leading to a fire or electric shock.
Be careful not to contact the print head, as you may get hurt or burned.
Make sure to insert the power plug as far as it will go. Improper insertion of the plug may develop fire or shock hazards.
Do not insert or drop any other time card than specified into the slot. Such misuse may cause a fire or electric shock.
If the unit should be dropped or the case be broken, unplug the unit and contact your dealer for servicing. Further use may lead to a fire or shock hazard.
Daily Care For cleaning, turn the power off and wipe the case clean of dust and dirt with a dry cloth, etc.



I NTRODUCTON:
Thank you for purchasing the 5000E plus. We are confident this Time Recorder will give you full satisfaction. Items such as the time and date are preset at the factory. After plugging in the AC power the Time Recorder can be used immediately. However, we recommend reading this manual before you start using your Time Recorder. FEATURES:
Main applications : Payroll/job cost recorder, time stamp or numbering machine.
The Quartz Time Recorder Dot-Matrix printer Perpetual calendar Automatic daylight saving time 4-way print activation Automatic Manual Semi-automatic Combination Adjustable print position Prints in 7 languages Prints numbers/date Time table program Special mark printing 13 preprogrammed comments
Alphanumeric printing Selectable 4-digit year imprint 12 or 24-hour format Regular minute, 1/10, 1/100 or 5/100 of an hour Password for program protection Digital LCD (Date, Hour, Minute, Day of the week indication) Wall or desktop mount Full power reserve (optional) Slave clock functions (optional) Built-in buzzer (optional) External Time Signal (optional)
For questions about the operation of this time clock, or to order supplies and accessories, please contact Lathem Time at (800)241-4990.
• • • •
Subject to high humidity and dust. Exposed to strong or continuous vibrations. Exposed to direct sunlight. The temperature range in which all functions of the Time Recorder will operate correctly is from -5˚C to 45˚C. Be sure therefore to place and use your Time Recorder only in locations in which this temperature range is not exceeded. Take care also not to subject your Time Recorder to any sudden, sharp temperature variations.

Package Contents Unpack the Time Recorder and check its contents to ensure that the Time Recorder unit and all accessories as shown below are included.

Print Position on Time Card

Print position from the card edge is adjustable by pressing and sliding the print position button located on the right outside bottom of the Time Recorder. Maximum distance from edge of form to print is approximately 1 3/16"(30mm).

<Print position adjuster> Display
Ribbon cassette

1 Unlock the key and remove the top case.
3 Replace the cover and lock.



2 Remove the PROTECTION PAD. 4 Plug the AC cord into the AC outlet and insert a card.

Following optional functions are available by adding an optional board. External Time Signal for Bell, Built-in Buzzer and Slave Clock. External Time Signal and Built-in Buzzer
External time signal and Built-in buzzer shall be controlled by Time table program and their duration settings. Refer to the "18.SETTING THE TIME TABLE PROGRAM", and the "19.SETTING THE EXTERNAL TIME SIGNAL / BUILT-IN BUZZER".
The Slave Clock is a function to synchronize the time of Time Recorder and the master clock. This function operates by choosing Slave Clock setup. Refer to the "20.SETTING THE SLAVE CLOCK".

To enter the program setting mode, you must plug the AC cord into the AC outlet and remove the cover. Next press the [SELECT] button once. Then the Time Recorder goes into the program mode showing the " "on the display positioned under the "TIME" mark.

Function of 3 control buttons [SELECT]: You can select the desired program setting mode by pressing this [SELECT]
button. Selected program setting mode is indicated by the " " on the display. [CHANGE]: When you press the [CHANGE] button, you can increment the set value. [SET]: You can set the value selected on the display by pressing the [SET] button.
Thereafter you press this [SET] button again, you can return the Time Recorder to the normal operation mode.

Example: Change the time from 10:08 to 10:09.
2 Change the "Minute". Press the [CHANGE] button to set at "09". And then press the [SET] button.
the " " under the "TIME" mark.
At that moment, the "Hour" flashes.
(The flashing means it can be changed.)

At that moment, the "Second" starts to run from "00".
Change the "Hour". In case of the example, press the [SET] button because the hour is not to be changed.
3 After you finish setting the time, press the [SET] button once again.
At that moment, the flashing changes from "Hour" to "Minute".
Now the time setting has been completed. Replace the cover and lock.

Example: Change the date from October 20, 2003 to October 21, 2003.
3 Change the "Date". Press the [CHANGE] button to set at "21". And then press the [SET] button.
the " " under the "DATE" mark.
At that moment, the "Year" flashes. (The
flashing means it can be changed.)

Change the "Year". In case of the example, press the [SET] button because the year 2003 is not to be changed.
4 After you finish setting the date, press the [SET] button once again.
At that moment, the flashing changes from "Year" to "Month".
2 Change the "Month". In case of the example, press the [SET] button because the month is not to be changed.
Now the date setting has been completed. Replace the cover and lock.
At that moment, the flashing changes from "Month" to "Date".

Example: Change the hour format to 24 hour.
1 Press the [SELECT] button and position the " " under the "HOUR" mark. At that moment, the flashing digit indicates "Hour Format Options". (The flashing means it can be changed.)
Change the "Hour". In case of the example, press the [CHANGE] button to set at "2". And then press the [SET] button.
PM 3:00
15:00
2 After you finish setting the 12/24 hour format, press the [SET] button once again.
Now the 12/24 hour setting has been completed. Replace the cover and lock.

Example: Set the print order to "Month, Date, Year, Hour, Minute".
1 Press the [SELECT] button and position the " " under the "PRINT ORDER" mark. At that moment, the flashing digit indicates "Print Order Options". (The flashing means it can be changed.)
Change the "Print Order Options". In case of the example, press the [CHANGE] button to set at "3". And then press the [SET] button.
Y=Year, M=Month, D=Date, DOW=Day of the week, H=Hour, Min=Minute, S=Second C=Comment, N=Number
M.D.H.Min
31 JAN '03 SENT
D.M.H.Min
Y.M.D.C
'03 JAN 31 SENT
M.D.Y.H.Min
C.D.H.Min
D.M.Y.H.Min
N.M.D.Y
000123 JAN 31 '03
Y.M.D.H.Min
N.D.M.Y
000123 31 JAN '03
Y.M.D.H.Min.S
N.Y.M.D
000123 '03 JAN 31
D.H.Min
31 10:00
JAN 31 '03 000123
DOW.D.H.Min
D.M.Y.N
31 JAN '03 000123
Y.M.D
'03 JAN 31
Y.M.D.N
'03 JAN 31 000123
M.D
JAN 31
N.D.H.Min
000123 31 10:00
FR, 31 JAN '03
N.M.D.H.Min
C.M.D.Y
SENT JAN 31 '03
N.Y.M.D.H.Min
C.D.M.Y
SENT 31 JAN '03
N.Y.M.D.H.Min.S
C.Y.M.D
SENT '03 JAN 31
N
M.D.Y.C
JAN 31 '03 SENT
2 After you finish setting the print order, press the [SET] button once again.
Now the print order setting has been completed. Replace the cover and lock.

In this setup, the printing of Year digit, the printing type of Minutes, and change of Leading Zero can be set.
Example: Change the Year imprint to 4 digits and the Minutes to 1/100 min. and the Leading
Zero to enabled.
Change the "Year Digit". In case of the example, press the [CHANGE] button to set at "2". And then press the [SET] button. At that moment, the flashing changes from the "Year Digit Options" to "Type of Minute".
the " " under the "PRINT PATTERN"
mark.
At that moment, the flashing digit
indicates "Year Digit Options".
(The flashing means it can be changed.)
SELECT CHANGE SET SELECT CHANGE SET
JAN 31 '03 10:00
JAN 31 2003 10:00
2 Change the "Type of Minute". In case of the example, press the [CHANGE] button to set at "2". And then press the [SET] button. At that moment, the flashing changes from "Type of Minute" to "Leading Zero".
1/60 Min.
1/100 Min.
1/20 Min. (= 5/100 Min.)
1/10 Min.

3 Change the "Leading Zero". In case of the example, press the [CHANGE] button to set at "2". And then press the [SET] button.
JAN 1 3:00
JAN 01 03:00
4 After you finish setting the print pattern, press the [SET] button once again.
Now the print pattern setting has been completed. Replace the cover and lock.

Example: Change the comment to "SENT".
Change the "Comment Options". In case of the example, press the [CHANGE] button to set at "2". And then press the [SET] button.
the " " under the "COMMENT" mark.
At that moment, the flashing digit
indicates "Comment Options".
(The flashing means it can be changed.)
RCVD (Received) SENT IN OUT CFMD (Confirmed) FILED PAID USED FAXED VOID ORIGN (Original) APR'D (Approved) CMPL'D (Completed)
JAN 31 '03 RCVD JAN 31 '03 SENT JAN 31 '03 IN JAN 31 '03 OUT JAN 31 '03 CFMD JAN 31 '03 FILED JAN 31 '03 PAID JAN 31 '03 USED JAN 31 '03 FAXED JAN 31 '03 VOID JAN 31 '03 ORIGN JAN 31 '03 APR'D JAN 31 '03 CMPL'D
2 After you finish setting the comment, press the [SET] button once again.
Now the preprogrammed comments setting has been completed. Replace the cover and lock.
Comment Options · Print Example

Example:
2 And then press the [SET] button. At that moment, the flashing digit changes from "Print Order Options" to "Print Position".
ABC HOTEL 1st comment line 21 OCT '03 2nd comment line (Date, Month, Year) BOSTON, MA 3rd comment line
1 Press the [SELECT] button and position
the " " under the "PRINT ORDER"
mark.
At that moment, the flashing digit
In case of example, press the [SET] button because the print position is not to be changed. Print Order Options
indicates "Print Order Options".
(The flashing means it can be changed.)
PRINT ORDER
Press the [CHANGE] button to set at the "30" (Customized Comments). At that moment, a digit for "Print Position" appears next to "Print Order Options".

4 Set the "Character Code". In case of example, the 1st character is "A", then enter the character code "02".
the " " under the "COMMENT" mark.
Setting the 1st comment line.
At the moment, the flashing digit
Refer to the "25. CHARACTER CODE FOR ALPHANUMERIC"
indicates "Character Position". And then
press the [SET] button.
Press the [CHANGE] button until the correct character code appears. And then press the [SET] button.
![Lathem Electronic Time Recorder (5000E Plus) — 3 Press the [SELECT] button and position diagram (page 19)](/cdn/reader/dc/dce36f59fd99eabf61d7ed8b01e16132978b0124959fe0f69b7629cbf0912ae4/images/fig-19-1.webp)
![Lathem Electronic Time Recorder (5000E Plus) — 3 Press the [SELECT] button and position diagram (page 19)](/cdn/reader/dc/dce36f59fd99eabf61d7ed8b01e16132978b0124959fe0f69b7629cbf0912ae4/images/fig-19-2.webp)
At the moment, the flashing changes
from "Character Position" to "Character
Code".
At that moment, the "Character Position" changes from the 1st character to the 2nd character.


5 The 2nd character is "B", then enter the character code "03".
7 Follow the same procedure for further characters settings.

8 Setting the 2nd comment line Press the [SET] button to change the comment line number to "C2".
Press the [CHANGE] button until the correct character code appears. And then press the [SET] button.
In case of example, the 1st character is "DATE", then enter the character code "28".
Press the [CHANGE] button until the correct character code appears. And then press the [SET] button.
6 The 3rd character is "C", then enter the character code "04".
Press the [CHANGE] button until the correct character code appears. And then press the [SET] button.


9 The 2nd character is "SPACE", then enter the character code "01".
Follow the same procedure for further characters settings.
Setting the 3rd comment line Press the [SET] button to change the comment line number to "C3".

Press the [CHANGE] button until the correct character code appears. And then press the [SET] button.

In case of example, the 1st character is "B", then enter the character code "03".
Press the [CHANGE] button until the correct character code appears. And then press the [SET] button.
The 3rd character is "MONTH", then enter the character code "27".


Press the [CHANGE] button until the correct character code appears. And then press the [SET] button.

13 The 2nd character is "O", then enter the character code "10".
15 After you finish setting the customized comments, press the [SET] button three times. Now the customized comments setting has been completed. Replace the cover and lock.

Press the [CHANGE] button until the correct character code appears. And then press the [SET] button.

Use below code number correction.
14 Set the last character "A" in the same manner as above.



ABC HOTEL
ABC HOTEL
21 OCT '03 BOSTON, MA
21 OCT '03 BOSTON, MA
Example: Change the print position to "Center orientated".
Change the "Print Position". In case of example, press the [CHANGE] button to set at "2". And then press the [SET] button.
Press the [SELECT] button and position
the " " under the "PRINT ORDER"
mark.
At that moment, the flashing digit
indicates "Print Order Options".
(The flashing means it can be changed.)
After you finish setting the print order and the print position, press the [SET] button once again.
In case of the example, press the [SET] button because the "Print Order Options" not to be changed. At that moment, the flashing digit indicates "Print position".
Now the print order and the print position settings have been completed. Replace the cover and lock.

Example: 1st comment line: No change. 2nd comment line: Change from "Year" to time "HH:MM". 3rd comment line: No change.

Confirming the 1st comment line To confirm the customized comments that have been set, press the [SELECT] button and position the " " under the "COMMENT" mark. At that moment, the "Character Position" flashes, and press the [CHANGE] button.
At that moment, the display changes to the following figure.
While the "Character Position" changes, the "Character Code" that has been set appears.
At this time, press the [SET] button twice, and the 2nd comment line is displayed.
After confirming the last character code of the 1st comment line, press the [CHANGE] button once again.

Changing the Customized Comments In case of example, press the [CHANGE] button to set at "5". And then press the [SET] button. At that moment, flashing changes from the "Character Position" to the "Character Code".
The character code "26" means "Year".
Position 2 3 4 5
SPACE
Press the [CHANGE] button to set at "2A".
The character code "2A" means HH:MM"
Position 2 3 4 5
SPACE
SPACE
HH:MM
Then press the [SET] button once.
Now changing the character code has been completed.
After you finish confirming and changing the customized comments, press the [SET] button once again. 4
Confirming the 3rd comment line Confirm the 3rd comment line in the same manner as Step 1. 3
Now confirming and changing the customized comments have been completed. Replace the cover and lock.

This setting is available if you select "Month", "Day of the week" or "Comment" in previous "PRINT ORDER". Example: Change the print language into Spanish.
Change the "Language". In case of the example, press the [CHANGE] button to set at "2". And then press the [SET] button.
the " " under the "LANGUAGE" mark.
At that moment, the flashing digit
indicates "Print Language Options".
(The flashing means it can be changed.)
TH, 25 DEC '03 OUT 31 10:00
ENGLISH
JU, 25 DIC '03 SAL 31 10:00
SPANISH
DO, 25 DEZ '03 AUSG 31 10:00
GERMAN
JE, 25 DEC '03 SORT 31 10:00
FRENCH
GI, 25 DIC '03 USC 31 10:00
ITALIAN
QI, 25 DEZ '03 SAIDA 31 10:00
PORTUGUESE
4, 25-12 '03 OUT 31 10:00
NUMERIC
2 After you finish setting the language, press the [SET] button once again. Now the language setting has been completed. Replace the cover and lock.
Print Language Options · Print Example

Example: Change the print direction to "Left" and the print activation to "Manual".
Change the "Print Direction". In case of the example, press the [CHANGE] button to set at "2". And then press the [SET] button. At that moment, the flashing changes from the "Print Direction" to the "Print Activation".
the " " under the "PRINT METHOD"
mark.
At that moment, the flashing digit
indicates "Print Direction Options".
(The flashing means it can be changed.)
Print method Print direction
PRINT METHOD
2 Change the "Print Activation". In case of the example, press the [CHANGE] button to set at "3". And then press the [SET] button.

3 After you finish setting the print method, press the [SET] button once again.
Now the print method setting has been completed. Replace the cover and lock.
Automatic will allow the Time Recorder to print by simply inserting a card or piece of paper.

Semi-automatic will allow the Time Recorder to print by pressing the push bar only when a card or piece of paper is inserted.
Manual will allow the Time Recorder to print by pressing the push bar.
Combination will allow the Time Recorder to print by pressing the push bar or inserting a card or piece of paper.
Push bar

Daylight Saving Time function
D.S.T. execution time At 2:00 a.m. on the first day of DST, the clock automatically gains one hour to show 3:00 a.m. When 3:00 a.m. comes on the last day of the DST, it loses one hour and returns to 2:00 a.m.
Setting D.S.T. Example: Start date Sunday, April 6, 2003 End date Sunday, October 26, 2003 If set as the above, the unit remembers the start date as the first Sunday of April and the end date as the last Sunday of October. Once set, the unit automatically updates the settings every year thereafter. No further manual setting is necessary.
Example
described using the following example.
Wednesday, January 29, 2003
Starting date of daylight saving time
Sunday, April 6, 2003
The first Sunday of April
Ending date of daylight saving time
Sunday, October 26, 2003
The last Sunday of October
1 Press the [SELECT] button and position the " " next to the "DAYLIGHT SAVING TIME" mark. (The flashing means it can be changed.)
" " mark means "starting date" setting
Today (present day) · Year · Month Date

Set the starting date.
2 Change the "Year". In case of the example, press the [SET] button because the year 2003 is not to be changed.
4 Change the "Date". Push the [CHANGE] button to set at "6" and push the [SET] button.
At the moment, the "startingt date" of the display changes from flashing to steady and the " " mark is displayed under "SU".
At the moment, the flashing changes from "Year" to "Month".

3 Change the "Month". Push the [CHANGE] button to set at "4" and push the [SET] button.
After a few second, go on to the "set the ending date". Please see the following page.
At the moment, the flashing changes from "Month" to "Date".

Set the ending date.
5 Change the "Year". In case of the example, press the [SET] button because the year 2003 is not to be changed.

7 Change the "Date". Push the [CHANGE] button to set at "26" and push the [SET] button.
At the moment, the flashing changes from "Year" to "Month".
At the moment, the "ending date" of the display changes from flashing to steady and the " " mark is displayed under "SU".
6 Change the "Month". Push the [CHANGE] button to set at "10" and push the [SET] button.

8 After you finish setting the daylight saving time, press the [SET] button once again.
At the moment, the flashing changes from "Month" to "Date".
Now the daylight saving time setting has been completed. Replace the cover and lock.

To delete and cancel the daylight saving time settings, change the display of "Month" of the starting setting to " ".
Example: To change April 6, 2003 of "starting date" and delete daylight saving time settings.
3 Press the [CHANGE] button to set at " ".
the " " next to the "DAYLIGHT
SAVING TIME" mark.
(The flashing means it can be changed.)

Press the [SET] button twice. This cancels the daylight saving time settings.
2 Press the [SET] button and the flashing changes from "Year" to "Month".
4 After you finish deleting the daylight saving time, press the [SET] button once again.
Now the deleting the daylight saving time has been completed. Replace the cover and lock.

In this setup, you can select digits of printed number, the Repeat Times of number, and type of Number Reset .
Example: Change the Number Digit to 4 digits and the Repeat Times to 2 times, and the
Reset to 0.
1 Press the [SELECT] button and position the " "next to the "NUMBER" mark. At that moment, the flashing digit indicates "Number Digit". (The flashing means it can be changed.)
Change the "Number Digit". The Number Digit can be set to 1 to 8. In case of the example, press the [CHANGE] button to set at "4". And then press the [SET] button. At that moment, the flashing changes from the "Number Digit" to "Repeat Times".
SELECT CHANGE SET SELECT CHANGE SET
Print Example: 6 Digits of Number 123456 JAN 31 '03 4 Digits of Number 1234 JAN 31 '03
2 Change the "Repeat Times". The Repeat Times can be set to 0 to 9. In case of the example, press the [CHANGE] button to set at "2". And then press the [SET] button. At that moment, the flashing changes from "Repeat Times" to "Reset Options".
(1st time) (2nd time) (3rd time) (4th time) (5th time)
123456 JAN 31 '03 123456 JAN 31 '03 123456 JAN 31 '03 123456 JAN 31 '03 123456 JAN 31 '03
(1st time) (2nd time) (3rd time) (4th time) (5th time)
123456 JAN 31 '03 123456 JAN 31 '03 123457 JAN 31 '03 123457 JAN 31 '03 123458 JAN 31 '03

3 Change the "Reset Options". In case of the example, press the [CHANGE] button to set at "3". And then press the [SET] button.
Execution event of Reset.
Return to INITIAL NUMBER
4 After you finish setting the number, press the [SET] button once again.
Now the number setting has been completed. Replace the cover and lock.

Example: Setting the initial number to "123". Refer to "16. SETTING THE NUMBER".
3 Set the correct numbers in the same manner as Step 2. And then press the [SET] button.
the " " next to the "INITIAL
NUMBER" mark.
At that moment, the flashing " "
indicates the 1st digit of the initial
number.
(The flashing means it can be changed.)
2 Set the "Initial Number". In case of the example, press the [CHANGE] button to set at "1". And then press the [SET] button.
4 After you finish setting the initial number, press the [SET] button once again.
At that moment, the 2nd digit of "Initial Number" appears next to "1" (the 1st digit).
Now the initial number setting has been completed. Replace the cover and lock.

The time table program function allows special mark "*" printing, an External Time Signal and a Built-in Buzzer. These functions can be programmed for each day of the week and each time period.
Example 1: The time table program is explained using the following example.
0:00 9:00 0:00 17:30
Special mark "*"
OFF
The following is time table based on the case above.
Program No.
Day of the week
Mon. - Fri.
9:00
Mon. - Fri.
17:30
1 Press the [SELECT] button and position the " " over the "TIME TABLE PROGRAM" mark. At that moment, the flashing digit indicates "Program No.". (The flashing means it can be changed.)
Setting program No. 1 (1) Set the "Day of the week". Press the [SET] button. At that moment, the flashing changes from the "Program No." to the "Day of the week".
In case of example, press the[CHANGE] button to set at "8". And then press the [SET] button. At that moment, the flashing changes from the "Day of the week" to the "Action".
Program No.
Day of the week
PROGRAM
TIME TABLE
PROGRAM
Day of the week Monday only Tuesday only Wednesday only Thursday only Friday only
Day of the week Saturday only Sunday only Monday to Friday Monday to Saturday Every day
Time · Special mark "*" · Action

2 (2)Set the "Action". Press the [CHANGE] button to set at "1". And then press the [SET] button.
(3)Set the "Hour". In case of example, press the [CHANGE] button to set at "9". And then press the [SET] button.

At that moment, the display changes to the following figure.
At that moment, the flashing changes from the "Hour" to the "Minute".
(4)Set the "Minute". In case of example, press the [CHANGE] button to set at "00". And then press the [SET] button.
TIME TABLE
PROGRAM

Make settings for Program No.2 in the same manner as for Program No.1, as illustrated in the following figure, and press the [SET] button.
Press the [CHANGE] button twice. At that moment, the display changes to the following figure.
BUZZ EXT. SIGNAL
*OFF *ON
PROGRAM
TIME TABLE
PROGRAM
4 After you finish setting the time table program, press the [SET] button once again. Now the time table program setting has been completed. Replace the cover and lock.
Example 2: The time table program is explained using the following example.
0:00 9:00 0:00 17:30 12:00
Ext. Signal
Ext. Signal Built-in Buzzer
Ext. Signal
Program No.
Day of the week
ON
Mon. - Sat.
9:00
Mon. - Sat.
9:00
Mon. - Sat.
12:00
Mon. - Sat.
17:30
& Built-in Buzzer · Built-in Buzzer · Time

1 Press the [SELECT] button and position the " " over the "TIME TABLE PROGRAM" mark. At that moment, the flashing digit indicates the "Program No.". (The flashing means it can be changed.)
No. Action
PROGRAM
2 Setting program No. 1 (1) Set the "Day of the week". Press the [SET] button. At that moment, the flashing changes from the "Program No." to the "Day of the week".
In case of example, press the [CHANGE] button to set at "9". And then press the [SET] button. At that moment, the flashing changes from the "Day of the week" to the "Action".
PROGRAM
Day of the week Monday only Tuesday only Wednesday only Thursday only Friday only
Day of the week Saturday only Sunday only Monday to Friday Monday to Saturday Every day
(2)Set the "Action". Press the [CHANGE] button to set at "3". And then press the [SET] button.
At that moment, the display changes to the following figure.
Selected Day of the week
*OFF *ON
TIME TABLE
TIME TABLE
PROGRAM
PROGRAM
Action Special mark "*" ON Special mark "*" OFF Ext. Signal ON Built-in Buzzer ON

(3)Set the "Hour".
In case of example, press the [CHANGE]
Press the [CHANGE] button twice. At that moment, the display changes to the following figure.
button to set at "9". And then press the
[SET] button.


Make settings for Program No.2 in the same manner as for Program No.1, as illustrated in the following figure, and press the [SET] button.
At that moment, the flashing changes from the "Hour" to the "Minute".

*OFF *ON
TIME TABLE
PROGRAM
BUZZ EXT. SIGNAL
TIME TABLE
PROGRAM
(4)Set the "Minute". In case of example, press the [CHANGE] button to set at "00". And then press the [SET] button.
*OFF *ON
TIME TABLE
PROGRAM


6 After you finish setting the time table program, press the [SET] button once again.
Make settings for Program No.3 in the same manner as for Program No.1, as illustrated in the following figure, and press the [SET] button.
Now the time table program setting has been completed. Replace the cover and lock.
Make settings for Program No.4 in the same manner as for Program No.1, as illustrated in the following figure, and press the [SET] button.


To confirm the programs that have been set, press the [SELECT] button and position the " " over the "TIME TABLE PROGRAM" mark. At that moment, the "Program No." flashes. And then press the [CHANGE] button.
After you finish confirming the program, press the [SET] button 6 times.
Now the time table program setting has been completed. Replace the cover and lock. Important: If you do not complete confirming the settings, the Time Recorder will not print.
Example: Deleting the "Program No.2".
1 To delete a program, make the "Program No." flash, and press the [CHANGE] button until the desired program No. is displayed.
3 Press the [SET] button. At that moment, the display changes to the following figure.

*OFF *ON
TIME TABLE
PROGRAM

Press the [SET] button. At that moment, the display changes to the following figure.
4 After you finish deleting a program, press the [SET] button once again.
Now the time table program setting has been completed. Replace the cover and lock.
2 Press the [CHANGE] button to set at " ".

This function is to set the durations of External Time Signal and Built-in Buzzer. For the number of seconds, 1 through 30 can be selected. Note:For this feature to be functional, the optional board must be installed in the Time Recorder.
Example: Change the External Time Signal to 30 seconds and the Built-in Buzzer to 10 seconds.
1 Press the [SELECT] button and position the " " over the "EXT. SIGNAL / BUILT-IN BUZZ." mark. At that moment, the flashing digit indicates the "Ext. Signal". (The flashing means it can be changed.)
Change the "Built-in Buzzer". In case of the example, press the [CHANGE] button to set at "10". And then press the [SET] button.

2 Change the "Ext. Signal". In case of the example, press the [CHANGE] button to set at "30". And then press the [SET] button.
After you finish setting the external time signal / bulit-in buzzer, press the [SET] button once again. 4
Now the external time signal / built-in buzzer setting has been completed. Replace the cover and lock.
At that moment, the flashing changes from the "Ext. Signal" to the "Built-in Buzzer".


In this setup, you can select the Slave Clock.
Signal Options (for Slave Clock)
Example: Set the Slave Clock and 60-second reversal.
1 Press the [SELECT] button and position the " " over the "SLAVE CLOCK" mark. At that moment, the flashing digit indicates "Clock Options". (The flashing means it can be changed.)
Set the "Signal Options". In case of the example, press the [CHANGE] button to set at "60". And then press the [SET] button.
SLAVE CLOCK
3 After you finish setting the slave clock, press the [SET] button once again.
Set the "Clock Options". In case of the example, press the [CHANGE] button to set at "1". And then press the [SET] button. At that moment, the flashing changes from the "Clock Options" to "Signal Options".
Now the slave clock setting has been completed. Replace the cover and lock.

When the password is set, you are asked to enter it. If the password you entered does not coincide with the setting, you cannot change the setting values. You may set a password by any 4-digit number from 0001 to 9998. Note : Number "0000" and "9999" cannot be used as a password.
Please reset all settings when you forgot the passward. Refer to the "22. RESETTING".
Example: Set the password "1234".
2 Change the last two digits. In case of the example, press the [CHANGE] button to set at "34". And then press the [SET] button.
the " " over the "PASSWORD" mark.
At the moment, the first two digits flash.
(The flashing means it can be changed.)
PASSWORD
Change the first two digits. In case of the example, press the [CHANGE] button to set at "12". And then press the [SET] button.
press the [SET] button once again.
At that moment, the flashing changes to the last two digits.
Now the password registering has been completed. Replace the cover and lock.

Once the password is set, you have to enter the password for changing any setting. "9999" will be displayed when you press the [SELECT] button.
1 Press the [SELECT] button, at that moment "9999" is displayed and the first two digits flash.
2 Set the last two digits. In case of the example, press the [CHANGE] button to set at "34". And then press the [SET] button.
(The flashing means it can be changed.)

Set the first tow digits. In the example, press the [CHANGE] button to set at "12". And then press the [SET] button.
At that moment, the " " mark indicates
the "TIME".
At that moment, the flashing changes to the last two digits.
3 Select desired setting mode by pressing the [SELECT] button.

The code "0000" must be entered to cancel the password.
Example: Cancel the password "1234".
1 Press the [SELECT] button, at that moment "9999" is displayed and the first two digits flash. (The flashing means it can be changed.)
3 Press the [SELECT] button and position the " " over the "PASSWORD" mark. At that moment, the first two digits "12" flash. (The flashing means it can be changed.)
In the example, press the [CHANGE] button to set at "12". And then press the [SET] button.
Press the [CHANGE] button to set at "00". And then press the [SET] button.
At that moment, the flashing changes to the last two digits.
At that moment, the flashing changes to the last two digits "34".
4 Press the [CHANGE] button to at set "00". And then press the [SET] button.
2 In case of the example, press the [CHANGE] button to set at "34". And then press the [SET] button.

5 After you finish canceling the password, press the [SET] button once again.
Now the password canceling has been completed. Replace the cover and lock.
At that moment, the " " mark indicates the "TIME".

To return all setting to the factory defaults, push the reset switch with a pointed implement.
Reset Switch

1 Install the supplied wall-mount screws into a wall by using the template. Be sure to keep about (1/4") 6mm of the screw head away from the wall.
3 Replace cover and lock.


2 Unlock the key and remove the cover. And then hang it on the wall.



3 Turn the knob of the new cassette in the direction of the arrow (clockwise) to tighten the ribbon.
2 Hold the ribbon cassette by its tab and pull straight out to remove it.
4 Place the cassette inside the Time Recorder as shown in the figure. Push the ribbon until it snaps into position. Turning the knob on the ribbon cassette may make installation easier.





5 Turn the knob of the cassette in the direction of the arrow to tighten the ribbon.
6 Replace the cover and lock.

Print head · Ribbon

Num: Sequential number HH: Hour MM: Minute SS: Second DOW: Day of the week 1 15: Language-Specific Character








English

1 Unlock the key and remove the cover. 3 Replace the cover and lock.


2 Insert the battery connector into the compartment connector to install the battery.


Connecting the Master Clock
Master Clock. Improper connection may cause a malfunction of the unit. Also refer to "Attaching the wire Clamp" to secure wires with the wire clamp.
1 Unlock the key and remove the cover. 3 Insert wires into two left terminals for the master clock, and tighten both screws.


59 mintue impulse (2-wire)
4 Replace the cover and lock. 2 The connector for the master clock signals is on the back of the Time Recorder.


30/60 second reversal · connector

External Time Signal. Improper connection may cause a malfunction of the unit. Also refer to "Attaching the Wire Clamp" to secure wires with the wire clamp.
1 Unlock the key and remove the cover. 3 Insert wires into two right terminals for external time signal, and tighten both screws.

4 Replace the cover and lock. 2 The connector for external time signals is on the back of the Time Recorder.


connector

clamp.
1 Remove two screws holding the wire clamp.

2 Make wires go through the hole of the wire clamp and secure it with screws. (See the Figure 1.) If diameter of wires is too small to fix by the above method, turn the wire clamp upside down and feed wires through the clamp. Then secure it with screws. (See the Figure 2.)

Wire clamp · Figure 2 Figure1

Error No. appears
Refer to the following list for proper operation.
E-00
Contact the store from whom you bought the unit.
The remaining life of lithium battery for memory back-up is short.
The card is not inserted in the Time Stamp properly.
Correctly insert the card.
Cannot print. The printer motor or home position sensor is not normal.
Make sure that the ribbon cassette is correctly inserted in place. Press the push bar.
Cannot print. The printer head motor or the sensor does not operate properly.
Enter the correct password again.
D.S.T. setting mistake
Make sure the correct starting and ending date of daylight saving time and enter again.
Setting data you entered is not usable.
Refer to your user's manual on the page related to the item you want to set and enter correct setting data.
CPU error · Incorrect password

Monthly accuracy ± 15sec. (at ordinary temperatures)
Year up to 2099. Automatically adjusted to leap years, 31-day months and months with thirty or fewer days, and the days of the week.
Three years of cumulative power failure hours after the date of shipment.
Print at power failure
Optional Ni-Cd battery, 200-time printing or 24 hours.
External time signal Built-in buzzer Printing an special mark (*)
Connection with optional functions. External Alarm device : No voltage signal output. Master Clock device : 6 to 32 V signal input.
Connection of external signal
Temperature: -5˚ to +45˚C, +23˚ to +113˚F Humidity: 20 to 80%, no condensation The unit operates normally at temperatures of 5˚C or below, but the print density, reaction of the liquid crystal display, and the number of prints at power failure are inferior to those at normal temperature operation.
6.14" (w) x 7.13" (h) x 6.97" (d) 156 (w) x 181 (h) x 177 (d) mm
Approx. 4.0 lbs. (1.8kg)
120VAC 50/60Hz 0.41A 220-240VAC 50/60Hz 0.2A

Lathem warrants the hardware products described in this guide against defects in material and workmanship for a period of one year from date of original purchase from Lathem or from an authorized Lathem reseller. The conditions of this warranty and the extent of the responsibility of Lathem Time Corporation ("Lathem") under this warranty are listed below.
1. This warranty will become void when service performed by anyone other than an approved Lathem warranty service dealer results in damage to the product. 2. This warranty does not apply to any product which has been subject to abuse, neglect, or accident, or which has had the serial number altered or removed, or which has been connected, installed, adjusted, or repaired other than in accordance with instructions furnished by Lathem. 3. This warranty does not cover dealer labor cost for removing and reinstalling the machine for repair, or any expendable parts that are readily replaced due to normal use. 4. The sole responsibility of Lathem under this warranty shall be limited to repair of this product, or replacement thereof, at the sole discretion of Lathem. 5. If it becomes necessary to send the product or any defective part to Lathem or any authorized service dealer, the product must be shipped in its original carton or equivalent, fully insured with shipping charges prepaid. Lathem will not assume any responsibility for any loss or damage incurred in shipping. 6. WARRANTY DISCLAIMER AND LIMITATION OF LIABILITY: Except only the limited express warranty set forth above, the products are sold with no expressed or implied warranties of any kind, and the implied warranties of merchantability and fitness for a particular purpose are hereby expressly disclaimed. No warranties are given with respect to products purchased other than from Lathem or an authorized Lathem reseller and any such products are purchased "as is, with all faults." In no event will Lathem be liable for any direct, indirect, special, incidental or consequential damages arising out of or in connection with the delivery, use or inability to use, or performance of this product. In the event any limited remedy given herein shall be deemed to have failed of its essential purpose, Lathem's maximum liability shall be to refund the purchase price upon return of the product. 7. Proof of date of purchase from Lathem or an authorized Lathem reseller is required for warranty service on this product. 8. This Warranty grants specific legal rights. Additional legal rights, which may vary by locale, may also apply. 9. Should any difficulties arise with the performance of this product during warranty, or with any Lathem authorized service centers, contact Lathem Time at the address below.
Lathem Time 200 Selig Drive, SW, Atlanta, GA 30336 404-691-0405 www.lathem.com Copyright © 2001 Lathem Time Corporation. All rights reserved.
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.