


This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense.
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS A LIMITS FOR RADIO NOISE EMISSIONS
FROM DIGITAL APPARATUS AS SET OUT IN THE RADIO INTERFERENCE REGULATIONS OF THE
CANADIAN DEPARTMENT OF COMMUNICATIONS.
LE PRÉSENT APPAREIL NUMÉRIQUE N'ÉMET PAS DE BRUITS RADIOÉLECTRIQUES DÉPASSANT LES
LIMITES APPLICABLES AUX APPAREILS NUMÉRIQUES DE CLASSE A PRESCRITES DANS LE
RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE ÉDICTÉ PAR LE MINISTÈRE DES
COMMUNICATIONS DU CANADA.
The details of this User's Manual are subject to change even without previous notification. This User's Manual has been prepared with the utmost care to cover all aspects of the time clock's use. Be sure to use your time clock after you have fully understood the hardware and software specifications and limits. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical, photocopying, recording or otherwise.
This User's Manual and its contents are copyrighted by LATHEM TIME CORP. with all rights reserved.

(800) 241-4990

Thank you for purchasing our time clock. For safe and proper operation, please carefully read the manual before using the time clock and save it for reference.
Main applications : Payroll/job cost recorder, time stamp or numbering machine.
Quartz time clock Dot matrix printer Perpetual calender Automatic daylight saving time 4-way print activation Automatic Manual Semi-automatic Combination
12 or 24-hour format Regular minute, 1/10, 1/100 or 5/100 of an hour Password for program protection Digital LCD display (Date, Hour, Minute, Day of the Week indication) Rigid enclosure, wall or desk top mount Full power reserve (optional)
C aution:
Place the time clock close to the wall outlet so that it is easily accessible to disconnect.
For questions about the operation of this time clock, or to order supplies and accessories, please contact Lathem Time at (800)241-4990.

Package Contents Unpack the time clock and check its contents to ensure that the time clock unit and all accessories as shown below are included.
1 ps.
4 pcs.
1 sheet.
AC Power Plug (230VAC model)
AC Power Plug (120VAC model)
Wall-mount holes

LOCATION OF NAME
It is important to become familiar with the time clock before setting it up and using it.

The print position from the card edge is adjustable by pressing and sliding the print position button on outside bottom.
The print position from the card edge is adjustable by pressing and sliding the print position button located on the right outside bottom of the recorder. Maxuim distance from edge of form to print is approximately 1 3/16"(30mm).
Key hole

Unlock the key and remove the top case.
Plug the AC cord into the AC outlet. When plugged in the LCD panel indicates the current time. It is now ready to be adjusted if necessary.

Insert a card.
Remove the PROTECTION PAD.

Remove the PROTECTION PAD before you plug the AC cord into the AC outlet.

PLEASE NOTE: If a time card is inserted and removed too quickly, the print head will move, but no imprinting will occur. This feature is designed to protect and maintain the life of your printer. Please hold the time card in the recorder until the print head movement is complete.

To enter the program setting mode, you should plug the AC power cord into the AC outlet and remove the cover. Thereafter press the 5 tactile switches, SW5 to SW1. < > indicates pressing a tactile switch. Pressing longer will realize faster increments.

SW5 : You can select the desired program setting mode by pressing this SW5 key. Selected program setting mode is indicated by the " " mark on the display.
SW4 , SW3 , SW2 : When you press the SW4 , SW3 and SW2 keys, you can increment the set value.
SW1 : You can set the value selected on the display by pressing the SW1 key. Thereafter you press this SW1 key again, you can return the clock to the normal operation mode.


TU WE TH FR SA SU MO HOUR MINUTE
Press the [SW2: MINUTE / DAY] key until the correct minute appears. Keeping the SW2 pressed, advances the minute automatically. Longer pressing speeds advancement.
Press the [SW5 : MODE] key once, the "HOUR MINUTE" arrow flashes.

Press the [SW1: SET] key after checking the desired time appears on the LCD. The seconds are 00. Press [SET] accordingly to a time signal. The unit is now set to correct time.
Press the [SW3 : HOUR / MONTH] key until the correct hour appears. The seconds are automatically reset to 00. Keeping the SW3 pressed, advances the hour automatically.



TU WE TH FR SA SU MO YEAR MONTH
Press the [SW2: MINUTE / DAY] key until the correct day appears. Keeping the SW2 pressed, advances the day automatically. Longer pressing speeds advancement.
Press the [SW5 : MODE] key twice, the "YEAR / MONTH / DAY" arrow flashes.

Press the [SW1: SET] key after checking the desired year, month and day on the LCD.
Press the [SW4 : YEAR] key until the correct year appears. Keeping the SW4 pressed, advances the year automatically. Longer pressing speeds advancement.


Press the [SW3 : HOUR / MONTH] key until the correct month appears.

When the daylight saving time is set, one hour will be automatically added to the day advance time on the starting date and, similarly, one hour will be automatically subtracted on the ending date of the daylight saving time.

TU WE TH FR SA SU MO START DAYLIGHT
Press the [SW2:MINUTE / DAY] key untli the correct day appears. Keeping the SW2 pressed,advances the day automatically. Longer pressing speeds advancement.
Press the [SW5:MODE] key three times, the "START DAYLIGHT SAVING" arrow flashes.


Press the [SW1:SET] key after checking the desired year, month and day on the LCD.
Press the [SW4:YEAR] key until the correct year appears. Keeping the SW4 pressed,advances the year automatically, Longer pressing speeds advancement.


If you do not use the daylight saving time function, set the month value to 00.
Press the [SW3 : HOUR / MONTH] key until the correct month appears.


TU WE TH FR SA SU MO END DAYLIGHT
Press the [SW2: MINUTE / DAY] key until the correct day appears. Keeping the SW2 pressed, advances the day automatically. Longer pressing speeds advancement.
Press the [SW5: MODE] key four times, the "END DAYLIGHT SAVING" arrow flashes.


Press the [SW1: SET] key after checking the desired year, month and day on the LCD.
Press the [SW4: YEAR] key until the correct year appers. Keeping the SW4 pressed, advances the year automatically. Longer pressing speeds advancement.


Press the [SW3 : HOUR / MONTH] key until the correct month appears.




Press the [SW5: MODE] key five times, the "INITIAL NUMBER SET" arrow flashes.
Press the [SW5: MODE] key six times, the "NUMBER REPEAT TIMES" arrow flashes.
Example: Setting initial number to 675829.
Example: Setting 2 times repeat. The repeat times can be set to 0 to 9.


Press the SW2, 3 or 4 key until the correct number appears. Longer pressing speeds advancement. Press the [SW1: SET] key after checking the desired number on the LCD.
Press the [SW2: MINUTE/DAY] key until the correct number appears. The repeat times can be selected 0 to 9. Press the [SW1: SET] key after checking the desired number on the LCD.



At the time of chenging the date, the number is automatically reset to "0".

Plug the AC cord out from the AC outlet. Confirm the LCD disappeared. If optional Ni-Cd battery is used, it should be taken off.
Press the [SW2: MINUTE/DAY] key until the correct number on the LCD.
Press the [SW1: SET] key after checking the desired number on the LCD.
Plug the AC cord into the AC outlet while pressing the [SW5: MODE] key. Then " 0 " is mentioned on the LCD.


Press the [SW5: MODE] key seven times, the "COMMENT" arrow flashes.
Example: Setting the comment to SENT.
Press the SW2 key until the correct number appears.
No.
1 2 3 4 5 6 7
RCVD SENT IN OUT CMFD FILED PAID
Press the [SW1:SET] key after checking the desired number on the LCD.
Comment

When the password is set, you are asked to enter it. If the password you entered does not coincide with the setting, you can not change the setting values. You may set a password by any 4-digit number from 0001 to 9998. Note a number "00 00" and "99 99" can not be used as a password.
TU WE TH FR SA SU MO S tep 3

Press the [SW2: MINUTE/DAY] key and assign the desired numbers to the last two digits.
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Set DIPSW 1-2, 4, 5, 8 and DIPSW 2-1, 3, 5, 7, 8 to ON. Then display shows "00 00".

Press the [SW1: SET] key. " " located right-below on the LCD will disappear that confirms password setting.
Press the [SW3: HOUR/MONTH] key and assign the desired numbers to first two digits.
Set DIP SW1, and 2 as desired position.

Once password is set, you have to enter the password for changing any settings. "99 99" will be displayed when you press the [SW5: MODE] key before entering password.
Press the [SW5: MODE] key.
Press the [SW1: SET] key.
Select desired setting mode by pressing the [SW5: MODE] key. Then make settings as explained.
DAY HOUR MONTH
Press the [SW3: HOUR/MONTH], [SW2: MINUTE/DAY] key until the correct number appears.

The code "00 00" must be entered to cancel the password.

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Set DIPSW 1-2, 4, 5, 8, and DIPSW 2- 1, 3, 5, 7, 8, to ON. Then display shows "99 99".
Press the [SW3: HOUR/MONTH], [SW2: MINUTE/DAY] key until "00 00" number appears.

Press the [SW1: SET] key. " " located right-below on the LCD will disappear that confirms password cancelation.

Press the [SW3: HOUR/MONTH], [SW2: MINUTE/DAY] key until the correct number appears.
Set DIPSW 1 and 2 as desired position.

Press the [SW1: SET] key.


Time can be displayed on a 12-hour (AM, PM) or 24-hour basis. DIP switch 2-5 is used for selection. Print also changed accordingly.
DIP switch 1-7:ON DIP switch 1-7:OFF
The DIPSW1-7 is used to select whether to print flush right or flush left on the card.
Leading 0 for hours less than 10 may be shown (enable) or suppressed (disable) on print.
DIP switch 2-4:ON


Semi-automatic print Only with the card inserted, pressing the push bar starts printing.
Manual print Even with no card, pressing the push bar starts printing.
Minute is printed in a unit which is obtained by dividing an hour by 60, 100, 20 or 10. DIP switches 2-2 and 2-3 are used for selection.
Combination Either inserting the card or pressing the push bar starts printing.


Year can be printed either 2 digits or 4 digits. DIPSW 1-6 is used for the selection.
You can choose 8 differents languages for printing month, day of the week, and preprogrammed comments.Use DIPSW 2-5 ~ 2-8 for setting.
Example Language
DIPSW1-6: ON 2001 OCT 21 AM10:08 English
DEC 21
AM10:08
Spanish
DIC 21
AM10:08
German
DEZ 21
AM10:08
French
DEC 21
AM10:08
Italian
DEC 21
AM10:08
Portuguese
DEZ 21
AM10:08
Roman
AM10:08
Numeric
AM10:08





1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8


1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
NUMBER OF YEAR DIGITS LEFT OR RIGHT PRINT PRINT SWITCH TYPE OF MINUTES LEADING 0 TYPE OF AN HOUR TYPE OF LANGUAGE 20

OTHER SPECIFICATIONS
Year up to 2099 (Automatically adjusted to leap year)
110 VAC, 120 VAC 230 VAC, 220-240 VAC
Clock accuracy
Monthly accuracy ±15 seconds (at ordinary temperatures)
Power consumption 110/120VAC 220-240/230VAC
20 VA max.while printing 4 VA while idling 0.2 A max.while printing 20 VA max.while printing 4 VA while idling 0.1 A max.while printing
Digital LCD with 7 segments Date, Hour, Minute and day of the week indication
Preprogramed comments
Selectable 7 different kinds
Operating -5˚C – 45˚C
Operating 20% – 80% RH (No condensation)
Available up to 3 lines
6 27/32" x 6 3/16" x 8 3/16" (174mm(W) x157mm(D) x208mm(H))
Memory Backup
3 year memory backup by lithium battery.
Approximately 5.5lb.(2.5 Kg)
OPTION
Impact Dot Matrix - 9pins 4-way Card activated automatic, manual, semi- automatic or combination
VIS6002
Battery
VIS6001 Available of 200 prints or 72 hours during no electricity.
Adjustable trigger trip Right/Left print by DIP switch
In case of power failure Even if a power failure has occurred, the optional built-in battery backs up to 72 hours (roughly three days), provided that the battery cells are fully charged.
12 or 24-hours format, regular minute, 1/10, 1/100 or 5/100 of a hour
No printing battery capacity The display is flashing when detecting the low battery capacity. Please stop printing until AC power supply is resumed.
Original + 4 (Maximum thickness 3mm or less)
If you still keep printing, the time recorder will hang up. When hung up, you have to press the RESET switch on the control panel by using a pair of tweezers. In this case, the calendar clock is cleared.
Carry-on cassette type fabric ink ribbon
Dies Gerät entspricht den Bedingungen der Niederspannungs-Vorschrift 73/23/EEC und dem EMVG nach 89/336/EEC. This unit complies with the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC.
Maschinenlärminformationsverordnung 3. GSGV,18.01.1991:Der arbeitsplatzbezogene Schalldruckpegel beträgt 70 dB(A) oder weniger gemäß ISO 7779.
Die zugeho¨rige Steckdose muß nahe beim Gerät angebracht und leicht zugänglich sein.
Auto · 16 poles
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.