Instruction/ maintenance manual of the product MT-84FA Lasko
Go to page of 50
OPERA TION AND P AR TS MANUAL Re vision #0 (06/10/05) SERIES MODEL MT -84F A T AMPING RAMMER (ROBIN GASOLINE ENGINE) THIS MANU AL MUST A CCOMP ANY THE EQUIPMENT A T ALL TIMES. T o find the latest revision of this publication, visit our website at: www .
P A GE 2 — MT -84F A — OPERA TION & P AR TS MANU AL — REV . #0 (06/10/05) MT -84F A — PROPOSITION 65 W ARNING.
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 3 NO TE P A GE.
P A GE 4 — MT -84F A — OPERA TION & P AR TS MANU AL — REV . #0 (06/10/05) MT -84F A — T ABLE OF CONTENTS MUL TIQUIP T AMPING RAMMER MT -84F A Proposition 65 W ar ning ......................................... 2 T able Of Contents .........
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 5 MT -84F A — P ARTS ORDERING PR OCEDURES When ordering parts, please supply the following information: ❒ ❒ ❒ ❒ ❒ D.
P A GE 6 — MT -84F A — OPERA TION & P AR TS MANU AL — REV . #0 (06/10/05) Safety precautions should be followed at all times when operating this equipment. F ailure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 7 MT -84F A — SAFETY MESSA GE ALER T SYMBOLS AL W A YS place the ON/OFF s witch in the OFF position when the rammer is not in use. AL W A YS wear appro ved e ye and hearing protection.
P A GE 8 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) The following safety guidelines should always be used when operating the MT -84F A T amping Rammer : GENERAL SAFETY ■ DO NO T operate or ser vice this equipment before reading this entire manual.
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 9 ■ AL W A YS stop the engine before servicing, adding fuel and oil. ■ NEVER run engine without air filter . Sev ere engine ma y occur . ■ AL W A YS ser vice air cleaner frequently to pre v ent carburetor malfunction.
P A GE 10 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) MT -84F A — OPERA TION AND SAFETY DECALS Machine Safety Decals The MQ Mikasa tamping rammer is equipped with a n umber of saf ety decals. These decals are provided f or operator saf ety and maintenance information.
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 11 MT -84F A — OPERA TION AND SAFETY DECALS Figure 1A. Rammer Operation and Safety Decals.
P A GE 12 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) Definition of T amping Rammer The Mikasa MT -84F A tamping rammer is a powerful compacting tool capable of applying a tremendous force in consecutive impacts to a soil surface.
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 13 MT -84F A — SPECIFICA TIONS Specifications are general and are subject to change without notice. If exact measurements are required, equipment should be weighed and measured.
P A GE 14 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) Figure 2 shows the location of the controls and components f or the MT -84F A T amping Rammer . The functions of each control is described below: L1 . A Returned Material Authorization must be approved by Multiquip prior to shipment.
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 15 MT -84F A — B ASIC ENGINE W ARNING W ARNING Figure 3. Robin EH-12-2D Engine Controls and Components INITIAL SER VICING The engine (Figure 3) must be checked for proper lubrication and filled with fuel prior to operation.
P A GE 16 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) Rammer Gearbox and Spring Cylinder Oil Bath This unit uses an oil bath lubrication system. P erfor m the f ollowing: 1 . Check the oil level through the oil level sight glass (Figure 4) at the rear of the tamper foot.
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 17 MT -84F A — OPERA TION Figure 7. Fuel Cock Inspection 1 . Check all nuts, bolts fast eners f or tightne ss. R etight en as necessar y . 2 . Clean any dirt from the recoil starter and foot pedestal.
P A GE 18 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) Operation 1 . T o star t the rammer tamping action, mov e the throttle le ver (Figure 11) quickly from IDLE (close) to the FULL OPEN position . DO NOT move the throttle lever slowly as this may cause damage to the clutch or spring.
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 19 Maintenance P erf or m the scheduled maintenance procedures as indicated: D AIL Y ■ Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as necessar y .
P A GE 20 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) MT -84F A — TR OUBLESHOO TING GUIDE G N I T O O H S E L B U O R T E N I G N E .
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 21 MT -84F A — TR OUBLESHOO TING GUIDE ENGINE ENGINE ENGINE ENGINE ENGINE ) d e u n i t n o c ( G N I T O O H S E L B U O R T E N I G N E . 4 E L B A T M O T P M Y S M E L B O R P E L B I S S O P N O I T U L O S y r o t c a f s i t a s t o n n o i t a r e p O .
P A GE 22 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) The contents and part numbers listed in the parts section are subject to change without notice .
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 23 MT -84F A — SUGGESTED SP ARE P AR TS Part number on this Suggested Spare Parts List may supersede/ replace the P/N shown in the text pages of this book. NOTE MT -84F A RAMMER 1 T O 3 UNITS Q T Y P A R T N O DESCRIPTION RE MARKS 1 .
P A GE 24 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) NAME PLA TE AND DECALS MT -84F A— NAMEPLA TE AND DECALS.
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 25 MT -84F A— NAMEPLA TE AND DECALS NAME PLA TE AND DECALS NO P AR T NO P AR T NAME QTY .
P A GE 26 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) MT -84F A — CRANKCASE AND ENGINE ASSY . CRANKCASE AND ENGINE ASSY .
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 27 MT -84F A — CRANKCASE AND ENGINE ASSY . CLUTCH GUIDE / A 1 4 5 0053204201 WOODRUFF KEY 1 4 6 301010210 LOCK W ASHER CLUTCH 1 4 7 956300130 THROTTLE LEVER A Y 25 1 CRANKCASE AND ENGINE ASSY .
P A GE 28 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) MT -84F A — CRANKCASE AND ENGINE ASSY . CRANKCASE AND ENGINE ASSY .
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 29 MT -84F A — CRANKCASE AND ENGINE ASSY . CRANKCASE AND ENGINE ASSY . CONTINUED NO P AR T NO P AR T NAME QTY .
P A GE 30 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) MT -84F A — GUIDE CYLINDER AND FOO T ASSY . GUIDE CYLINDER AND FOO T ASSY .
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 31 MT -84F A — GUIDE CYLINDER AND FOO T ASSY . GUIDE CYLINDER AND FOO T ASSY . NO . P A R T N O . P ART NAME QTY . REMARKS 1 352423290 PISTON PIN 1 2 363457870 PISTON PIN PLUG 2 3 361344360 PISTON ROD 1 4 355452340 PISTON END 1 5 020118150 N U T M 18, P1.
P A GE 32 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) MT -84F A — T ANK AND HANDLE ASSY . T ANK AND HANDLE ASSY ..
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 33 MT -84F A — T ANK AND HANDLE ASSY . T ANK AND HANDLE ASSY . NO P AR T NO P AR T NAME QTY . REMARKS A 305910032 FUEL T ANK ASSY .................................. 1 .........
P A GE 34 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) ROBIN EH-12-2D46420 ENGINE — CRANKCASE AND CYLINDER ASSY . CRANKCASE AND CYLINDER ASSY .
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 35 ROBIN EH-12-2D46420 ENGINE — CRANKCASE AND CYLINDER ASSY . CRANKCASE AND CYLINDER ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS 1 0 2521030131 CRANK CASE ...............
P A GE 36 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) CRANKSHAFT AND PIST ON ASSY . ROBIN EH-12-2D46420 ENGINE — CRANKSHAFT AND PIST ON ASSY .
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 37 ROBIN EH-12-2D46420 ENGINE — CRANKSHAFT AND PIST ON ASSY . — E— CRANKSHAFT AND PIST ON CRANKSHAFT AND PIST ON ASSY . NO. P AR T NO . P AR T NAME QTY . REMARKS 1 0 2682190111 CRANKSHAFT CP 1 4 0 0230250110 S P A CER T=0.
P A GE 38 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) MUFFLER,AIR CLEANER,CAMSHAFT & CARBURET OR ASSY . ROBIN EH-12-2D46420 ENGINE—MUFFLER,AIR CLEANER, CAM& CARB.
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 39 MUFFLER, AIR CLEANER, CAMSHAFT & CARBURET OR ASSY . NO. P AR T NO . P AR T NAME QTY . REMARKS 1 0 2533170111 CAMSHAFT CP ......................... 1 ......................
P A GE 40 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) GO VERNOR ASSY . ROBIN EH-12-2D46420 ENGINE — GO VERNOR ASSY ..
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 41 ROBIN EH-12-2D46420 ENGINE — GO VERNOR ASSY . GO VERNOR ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS 1 0 2524230303 GO VERNOR LEVER CP 1 2 0 2264230207 GO VERNOR SHAFT .
P A GE 42 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) RECOIL ST ARTER AND BLO WER ASSY . R OBIN EH-12-2D46420 ENGINE — RECOIL ST ARTER AND BLO WER ASSY .
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 43 RECOIL ST ARTER AND BLO WER ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS 1 0 2525165221 BLOWER HOUSING CP 2 1 2 0 92010.
P A GE 44 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) R OBIN EH-12-2D46420 ENGINE — MA GNET O ASSY . MA GNET O ASSY ..
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 45 R OBIN EH-12-2D46420 ENGINE — MA GNET O ASSY . MA GNET O ASSY . NO P AR T NO P AR T NAME QTY .
P A GE 46 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) ROBIN EH-12-2D46420 ENGINE — CARB URET OR ASSY . CARBURET OR ASSY .
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 47 R OBIN EH-12-2D46420 ENGINE — CARBURET OR ASSY . CARBURET OR ASSY . NO P AR T NO P AR T NAME QTY .
P A GE 48 — MT -84F A — OPERA TION & P ARTS MANU AL — REV . #0 (06/10/05) Multiquip reserves the right to quote and sell direct to Government agencies, and to Origi- nal Equipment Manufacturer accounts who use our products as integral parts of their own products.
MT-84FA — OPERATION & PARTS MANUAL — REV. #0 (06/10/05) — PAGE 49 NO TE P A GE.
OPERA TION & P AR TS MANUAL Y our Local Dealer is: HERE'S HOW TO GET HELP PLEASE HA VE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING © COPYRIGHT 2005, MUL TIQUIP INC. Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc.
An important point after buying a device Lasko MT-84FA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lasko MT-84FA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lasko MT-84FA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lasko MT-84FA you will learn all the available features of the product, as well as information on its operation. The information that you get Lasko MT-84FA will certainly help you make a decision on the purchase.
If you already are a holder of Lasko MT-84FA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lasko MT-84FA.
However, one of the most important roles played by the user manual is to help in solving problems with Lasko MT-84FA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lasko MT-84FA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
