Instruction/ maintenance manual of the product WT-5432 La Crosse Technology
Go to page of 16
WT-5432 433 MHz Radio Controlled Projection Alarm Instruction Manual.
2 TABLE OF CONTENTS Topic Page Inventory of Conte nts/ Addi tional Equi pment 3 About WW VB 3 Quick Set-U p Guide 4 Detailed Set-Up Guide Battery Installation 5-6 Program Mode Programming Sequence 6 F.
3 INVENTORY OF CO NTENTS 1) WT-5432 p ro j ect i on alarm 2) TX6U remote temperature se nsor 3) AC adapter/transformer (6V) 4) Instructi on manual a nd warranty card. ADDITIONAL EQUIPME NT (not included) 1) Three fres h 1.5V AA bat teries (optio nal for alarm clock) 2) Two fresh 1.
4 B attery Cover NOTE: Fog and mist will not harm your remote sensor but direct rain must be avo ided. To complete the set up of your temperatur e station after the 10 minutes have passed please follow the steps starting on page 6. DETAILED SET-UP GUIDE Important: Insert batteries into the trans mi tter first, then into the alarm clock.
5 the WWVB search is being condu cted various numbers will appear in th e time display. After 10 minutes, the projection a larm will either display the WWVB time or discontinue the sea rch if the time is not found. If the search is cancelled “-:--” will remain in the time LCD.
6 4. From –5h to –8h, a US map with the highlighted time zone will also be displayed to the right of the time display. 5. Press and release the “SET” button to confirm the time zone setting, and to advance to DS T (Daylight sa ving time) set ting.
7 Note: when setting the hour, “PM” will appear to the left of the hour disp lay, if it is AM nothing will be displayed. 2. Press and release the “SET” button to confirm the hour setting and to sh ift to select the minutes. 3. Press and release the “+” button t o select the minutes.
8 5. Six modes of date/secon ds/temperature dis play 6. Indoor temperature 7. Remote outdoor tem perature 8. Dual alarms 9. Adjustable snooze B. Radio-Controlled Time and Date 1. The projection alarm will automatically search for the time signal upon initial set-up and every nigh t.
9 between time and remote temp eratur e (M2) by pressing the “DISPL” button. The selected display mode will flash on the lower left as “M0”, “M1” or “M2”. 12. The direct ion of the display ca n also be rotat ed 360 ° in 90 ° i ncrements by pressing the d irectional button.
10 Clouds with Ra in —indicates that the weather is expected to get worse (not that the weather will be rainy). The weather icons cha nge when the unit detects a change in air pressure. The icons ch ange in order, from “sunny” to “par tly sunny” to “cloudy” or the reverse.
11 5. The transmitter should not be mounted on a metal surface. 6. The transmitter and projection alarm should be kept away from other sources of possible interference incl ud ing cordless appliances (teleph ones, baby monito rs), microwave ovens, and other strong electric al appliances.
12 c. To disable the alarm for 24 hours press and release any butt on ot he r than the “SNOOZE” bar or project i o n key s. H. Changi ng the Di spl a y M ode (D ay, Seconds and Tempe rature) There are six possible display modes to view t he day, seconds a nd temperature (remote temperature is constantly disp layed).
13 3. Adhere the tape to the designated area on the back of the mounting bracket. 4. Remove the protective stri p from t he other side of the tape. 5. Position the remote temperature sensor in the d e sired location, ensuring that the projection alarm can receive the signal.
14 reception. 6) If problems persist contact La Crosse Technology. Problem: Hour is incorre ct (minut e and date are correct). Solution: 1) Be sure corr ect time zone and day light savi ng time are selected.
15 WARRANTY INFORMATION La Crosse Technology provides a 1-year wa rranty on this projection alarm. Contact La Crosse Technology i mmediately upon discovery of any defects covere d by this warranty. Before sending the proj ectio n al arm in for re pairs, contact La Crosse Technology for a return authorization.
16 FCC ID: OMO-01RX (receiver) OMO-01T X (transmi tter) THIS DEVICE COMPLIE S WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO TH E FOLLOWING TWO CONDIT IONS: 1. THIS DEVICE MAY NOT CA USE HARMFUL INTER FERENCE, AND 2. THIS DEVICE MUST ACCEPT INTERFERE NCE RECEIVED, INCLUDIN G INTERFERENCE T HAT MAY CAUSE UNDES IRED OPERATION.
An important point after buying a device La Crosse Technology WT-5432 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought La Crosse Technology WT-5432 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data La Crosse Technology WT-5432 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, La Crosse Technology WT-5432 you will learn all the available features of the product, as well as information on its operation. The information that you get La Crosse Technology WT-5432 will certainly help you make a decision on the purchase.
If you already are a holder of La Crosse Technology WT-5432, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime La Crosse Technology WT-5432.
However, one of the most important roles played by the user manual is to help in solving problems with La Crosse Technology WT-5432. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device La Crosse Technology WT-5432 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
