Instruction/ maintenance manual of the product FS-1035MFP Kyocera
Go to page of 79
.
.
.
.
iii Contents 5 Sending Functions Original Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Sending Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv Contents 1 1 Management User Login Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 -2 Job Accounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
v Quick Guide T o make copies T o print Simply pres s the Start key to make copies. You can also fine tune the copy settings by changi ng the paper size, adjusting the de nsity, etc. You can print via a network an d over the USB co nnection or prin t a PDF file directly from USB memory.
vi T o send document s You can send scanned images via a network and over the USB connection. Or, you can also store scanned images in USB memory. Administrator tasks It sends.
vii T o send a F AX(F A X functions available only in FS-1 130MFP/FS-1 1 35MFP) As well as sending a FAX via the teleph one lines, you can also se nd a FAX via a network. NOTE: Fo r more information on se tting up and sending a F AX, refer to the F AX Operation Guide .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2 Preparation before Use 2-7 Power Off Timer If the machine is not used while in sleep mode , the power automatically turns off. The Power Off Timer is used to set the time until the power turns off. The factory setting for the time until the power turns off is 1 hour.
Preparation before Use 2-8 Switching the Language for Display [Language] Select the language displayed on the Message Display. Use the procedure below to select the lan guage. 1 Press the Power switch. 2 Press the System Menu/Counter key on the main unit operation p anel.
2 Preparation before Use 2-9 6 Press the OK key . Language appears. 7 Press the U or V key to select the desired language and then pre ss the OK key . Completed.
Preparation before Use 2-10 Setting Date and Time Follow the steps below to set the local date a nd time at the pl ace of installation. When you send an E-mail using the transmission function, the date and time as set here will be printed in the header of the E-mail message.
2 Preparation before Use 2-11 8 Press the OK key . Time Zon e appears. 9 Press the U or V key to select your reg ion and then press the OK key . Completed. is disp layed and the screen returns to the Date Setting menu. 10 Press the U or V key t o select [Summer T ime].
Preparation before Use 2-12 16 Press the Y or Z key to move the cursor position, press the U or V key to enter hours, minutes and se conds, and then press the OK key . Completed. is disp layed and the screen returns to the Date Setting menu. 17 Press the U or V key t o select [Date Format].
2 Preparation before Use 2-13 Network Setup (LAN Cable Connection) The machine is eq uipped with network in terface, which is compatible with network protocols such as TCP/IP (IPv4), TCP/IP (IPv6), IPX/SPX, NetBEUI, IPSe c, and AppleTalk. It enables network printing on the Windows, Macintosh, UNIX, NetWar e and othe r platforms .
Preparation before Use 2-14 NOTE: After all network related settings hav e been done, turn the ma chine OFF and ON again. This is mandatory to make the settings ef fective! NetW are On/Off Frame T y p.
2 Preparation before Use 2-15 Inst alling Sof tware Ensure the printer is plugge d in and connected to the PC before installing the printe r driver from the DVD. Inst alling the Sof tware in W indows If you are connecting this printe r to a Windows PC, follow the next steps to install the printer drive r.
Preparation before Use 2-16 4 Click Inst all sof tware . The software install wizard start s up. From this point, the procedure diffe rs depending on your version of Windows and your connectio n method. Proceed to the correct procedure for your connection type.
2 Preparation before Use 2-17 2 Select the printer you want to be installed, and click Next . NOTE: If the Found Ne w Hardware Wizard appear s, click Cancel . If a hard ware inst allation warning messag e appear , click Continue . 3 Y ou can customize the print system name in the installation settings window .
Preparation before Use 2-18 Custom Mode Use Custom Mode if you want to specify the printe r port and s elect the so ftware to be installed. For example, if you do not want fonts installed on your computer to be replaced, select Custom Mode and deselect the Font s checkbox in the utility tab.
2 Preparation before Use 2-19 4 Double-click either OS X 10.2 and 10.3 Only , OS X 10.4 Only or OS X 10.5 or higher depending on your Mac OS version. 5 Double-click Kyocera OS X x.
Preparation before Use 2-20 7 Choose Sele ct Destina tion , Inst allation T ype and then install the printer dr iver as directed by the instructions in the installation sof tware.
2 Preparation before Use 2-21 10 Click the IP icon for an IP connec tion and then enter the IP addr ess and printer name. When you click the AppleT al k icon for an AppleT alk co nnection, enter the printer name . NOTE: AppleT alk icon is not displa yed on Mac O S X 10.
Preparation before Use 2-22 12 Select the options availabl e for the printer and click Continue . 13 The selected printer is added . This completes the printer setup procedure. Uninst alling Sof tware (W indows PC) The softw are can be uninstalled (re moved) us ing the DVD ( Product L ibrary) supp lied with the printer.
2 Preparation before Use 2-23 5 Click Uninst all . NOTE: When KMnet V iewer is inst alled, separa te uninst allers are launched for this app lication. Proceed with the uninstallation step s for this application as directed by the on-s creen instructio ns.
Preparation before Use 2-24 4 Click T next to the Model field and select this machine from the list. 5 Click User Authentication Settings . If user login administration is invalid, go to S t ep 7. 6 Select the checkbox beside Authen tication, enter Login User Name (up to 64 char acters) and Passw ord (up to 64 characters) and then click OK .
2 Preparation before Use 2-25 Setting the WIA Driver (Windows Vi st a™, Windows® Server 2008 and Windows 7) Register this machine to the WIA Driver . NOTE: The following is not necessary to register wh en using the machine posse sses an IP address or host name that you have specified during inst allation of WIA Driver .
Preparation before Use 2-26 COMMAND CENTER (Settings for E-mail) COMMAND CENTER is a tool used for tasks such as verifyin g the op erating status of the m achine and changin g the settings f or securit y, network p rinting, E-mail transmission and advanced networkin g.
2 Preparation before Use 2-27 Sending E-mail Specifying the SMTP settings allows you to send images loaded onto this machine as E-mail attachments. To use this function, this machine must be conn ected to a mail serve r using the SMTP protoc ol.
Preparation before Use 2-28 2 Enter the correct settings in each field. The settin gs to be sp ecified in the SM TP settings s creen are shown be low . 3 Click Submit. Item Description SMTP Protocol Ena bles or disables SMTP prot ocol. T o use E-mail, this protocol must be enabled.
2 Preparation before Use 2-29 Prep aration for sending a document to a PC Check the information that ne eds to be set on the machine and create a folder to re ceive the document on your computer. Screens of Windows 7 are us ed in the following explanation.
Preparation before Use 2-30 2 At the Command Prompt, enter "net config workst ation" and then click Enter . Screen example: user name "james.smi th" and domain name "ABCDNET" Creating a Shared Folder Check the domain name and user name for logging onto Windows.
2 Preparation before Use 2-31 1 Create a folder on the local disk (C). NOTE: For example, crea te a folder with the name "scannerdat a" on the local disk (C). 2 Right-click the scannerdata folder and click Share and Advanced s haring . Click the Advanced Sh aring button.
Preparation before Use 2-32 5 Enter the user name which you conf irmed on Checking what to enter for [Logi n User Name] on 2-29 in the text box and click the OK button. 6 Select the entered user , select th e Change and Read permissions, and click the OK button .
2 Preparation before Use 2-33 8 Click the Security t ab and then click the Edit button. In Windows XP , click the Security t ab and then click th e Add button. 9 Proceed in the same way as in step 5 to add a user to Group or user names . 10 Select the added user , select the Modify and Read & execute perm issions, and then click the OK button.
Preparation before Use 2-34 Checking t he [Path] Check the share name of the sh ared folder that will be the destination for the document. 1 Enter the computer name (ex. pc4050) in "Program and File Search" in the Start menu. The Search Result s scree n opens.
2 Preparation before Use 2-35 Configuring Windows Fi rewall (for W indows 7) Permit sharing of files and prin ters and set the port used fo r SMB transmission.
Preparation before Use 2-36 2 Click Advanced settings . 3 Click Inbound Rules . 4 Click New Rule . 5 Select Port and click Next . 6 Select TCP , select S pecific local port s , enter "139", and click Next .
2 Preparation before Use 2-37 7 Select Allow the connection and click Next . 8 Make sure all checkboxes are selected and click Next . 9 Enter "Scan to SMB" in "Name" and click Finish .
Preparation before Use 2-38 NOTE: In Windo ws XP or Windows Vist a, follow the procedure below to set the port. 1 From the St art menu, select Control Panel , Sy stem and Security (or Security Center ), and th en Check Firew all Status ) (o r Windows F irewall ).
2 Preparation before Use 2-39 Loading Paper Paper can be loaded stand ardly in the cassette and the mult i purpose tray. A paper fe eder is also available as an option (refer to Optional Equipm ent on Appendix-2 ).
Preparation before Use 2-40 Loading Paper in the Cassettes The standard cassette will each hold plain paper, recycled paper or color paper. The standard cassette holds up to 25 0 sheets of A4 or smaller plain paper (80 g/m2).
2 Preparation before Use 2-41 3 Adjust the position of the p aper wid th guides locate d on the left and right sides of the casset te. Press the p aper width ad justing tab on th e left gu ide and slide the guides to the paper size r equired. NOTE: Paper sizes are marked on the cassette.
Preparation before Use 2-42 5 Load the paper in the cassette . Ensure the side to be printed is facing down and the p aper is not folded, cur led, or damaged. IMPORTANT: Do not load paper above the triangle mark located on the width guide. • B e fore loading the pap er , be sure that it is not curled or folded.
2 Preparation before Use 2-43 Loading Paper in the Multi Purpose T r ay The multi purpose tray will hold up to 50 shee ts of A4 or smalle r plain paper (80 g/m 2 ). The multi purpose tray accepts paper sizes from A4 to A6 and Hagaki an d from Legal to Statement-R, 216 x 340 mm, and 16K.
An important point after buying a device Kyocera FS-1035MFP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kyocera FS-1035MFP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kyocera FS-1035MFP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kyocera FS-1035MFP you will learn all the available features of the product, as well as information on its operation. The information that you get Kyocera FS-1035MFP will certainly help you make a decision on the purchase.
If you already are a holder of Kyocera FS-1035MFP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kyocera FS-1035MFP.
However, one of the most important roles played by the user manual is to help in solving problems with Kyocera FS-1035MFP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kyocera FS-1035MFP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
