Instruction/ maintenance manual of the product DiMAGE Z3 Konica Minolta
Go to page of 124
INSTRUCTION MANUAL E 9222-2733-11 MS-A406/0406/109678.
2 Before you begin Thank you for purchasing this digital camera. Please take the time to read through this instruction manual so you can enjoy all the features of your new camera. Check the packing list before using this product. If any items are missing, immediately contact your camera dealer .
3 Read and understand all war nings and cautions befor e using this product. Using batteries impr operly can cause them to leak harmful solutions, overheat, or explode which may damage pr operty or cause personal injury . Do not ignore the following war nings.
4 For proper and safe use • Use only the specified AC adapter within the voltage range indicated on the adapter unit. An inap- propriate adapter or current may cause damage or injury through fire or electric shock. • Do not disassemble this product.
5 • Do not point the lens directly at the sun, a fire may result. Replace the lens cap when the camera is not in use. • Do not use or store the pr oduct in a hot or humid environment such as the glove compartment or trunk of a car .
6 T able of contents The basic operation of this camera is covered between pages 12 and 33. This section of the manual covers the camera parts, preparation of the camera for use, and the basic camera operation for recor ding, viewing, and deleting images.
7 Basic playback .....................................................................................................................................30 Single-frame playback and histogram display ......................................................
8 T able of contents A short guide to photography ..............................................................................................................68 Advanced playback.......................................................................
9 Data-transfer mode ..............................................................................................................................97 System requir ements ................................................................................
10 Names of parts * This camera is a sophisticated optical instrument. Care should be taken to keep these surfaces clean. Please r ead the car e and storage instructions in the back of this manual (p. 116). Names of parts Shutter -release button Lens* Self-timer lamp (p.
11 Viewfinder* (p. 17) LCD monitor* Access lamp Exposure-mode dial (p. 21, 29, 36 - 40) Accessory shoe (p. 43) Controller Zoom lever (p. 20) Menu button Quick View / Delete button (p. 30, 31) Information button (p. 28, 32) Mode switch Main switch Flash-mode button (p.
12 Getting up and running GETTING UP AND RUNNING Always keep the strap around your neck in the event that the camera is accidentally dr opped. An optional leather neck strap, NS-DG1000, is also available from your Konica Minolta dealer . Availability varies with region.
13 Inserting batteries Insert the batteries as indicated on the diagram on the inside of the bat- tery-chamber door . Confirm the positive and negative battery terminals are oriented correctly . T o open the battery-chamber door , slide the door toward the side of the camera (1) to release the safety catch.
14 Getting up and running Battery condition indicator Full-battery indicator - the battery is fully charged. This indicator is displayed for three seconds on the monitor when the camera is tur ned on. Low-battery indicator - battery power is low . The battery should be replaced as soon as possible.
15 Connecting the optional AC adapter The AC Adapter allows the camera to be powered from an electrical household outlet. The AC Adapter is recom- mended when the camera is interfaced with a computer or during periods of heavy use. AC Adapter model AC-1L is for use in North America and Japan, and AC-11 is for use in all other areas.
16 Getting up and running Changing the memory card An SD Memory Card or MultiMediaCard must be inserted for the camera to operate. If a card has not been inserted, a no-card warning is displayed on the monitor . For more about memory cards see page 118.
17 T ur ning on the camera and displays Press the main switch to turn the camera on. Pressing the switch again turns the camera of f. When the camera is tur ned on, the Anti-shake indicator appears on the LCD monitor . Around the main switch is the mode switch.
18 Getting up and running Use the left and right keys to select the item to be changed. Use the up and down keys to adjust the item. Press the central button to set the clock and calen- dar . Setting the date and time After initially inserting a memory card and batteries, the camera’ s clock and calendar must be set.
19 Use the down key to highlight the language menu option. Press the central button to complete the operation. Press the right key to highlight the current language. Press the central button to open the language screen. Setting the Menu language For customers in certain areas, the menu language may have to be set.
20 Basic recor ding BASIC RECORDING While using the viewfinder or LCD monitor , grip the camera firmly with your right hand while supporting the body with your left. Keep your elbows at your side and your feet shoulder -width apart to hold the camera steadily .
21 Recor ding images automatically T ur n the exposure-mode dial to the auto-recording position (1); all camera operations are now fully automatic. The autofocus, exposure, and imaging systems will work together to bring beautiful results effortlessly .
22 Basic recor ding Press the shutter -release button all the way down to take the pic- ture. The example uses auto recording. Except for movie recor ding, the operation for other exposure modes is the same. Automatic Digital Subject Program Selection is only available in the auto recording mode.
23 Automatic Digital Subject Pr ogram Selection Automatic Digital Pr ogram Selection chooses between program autoexposure and one of four digi- tal subject pr ograms. The digital subject programs optimize camera setting for various conditions and subjects.
Basic recor ding 24 Focus lock pr events the AF system from focusing. This can be used with off-center subjects or when a special focusing situation prevents the camera from focusing (p. 25). Without lifting your finger from the shutter -release button, recompose the subject within the image ar ea.
25 The focus signal in the lower right cor ner of the LCD monitor indicates the focus status. The shutter can be r eleased even if the camera cannot focus on the subject. The camera may not be able to focus in certain situations. If the autofocus system cannot focus on a subject, the focus signal will tur n r ed.
T o use the built-in flash, simply raise it (1). Lower the flash unit to prevent it from firing. Flash-mode indicator turns red while the flash is charging; wait until it becomes white before taking pictures. T o change the flash mode, simply press the flash mode button (2) until the appropriate mode is indicated.
27 If the shutter speed falls below the point where the camera can be safely hand held, regardless if Anti-shake is active or not (p. 95), the camera-shake warning appears on the LCD monitor . Camera shake is slight blurring caused by subtle hand motion and is more pro- nounced at the telephoto position of the lens than at the wide-angle.
The monitor image can be made lighter or darker . The brightness level can be set individually for viewfinder and direct viewing. T ur n the mode switch to the appropriate position. Press and hold the information (i + ) button to open the LCD brightness screen.
29 Digital subject programs Sports action - used to capture action by maximizing shutter speeds. The AF system con- tinuously focuses; see page 25. When using flash, the subject must be within the flash range (p. 27). A monopod is more flexible and compact than a tripod when shooting events.
Images can be viewed in the Quick View or playback modes. This section covers the basic operations in both modes. The playback mode has additional functions, see page 70. T o view images from the playback mode, tur n the mode switch to the playback position (1).
31 The histogram shows the luminance distribution of the image from black (left) to white (right). The 256 vertical lines indicates the relative pr oportion of that light value in the image. The histogram can be used to evaluate exposure, but displays no color information.
32 Basic playback In index playback, the four -way keys of the controller will move the yellow bor der . When the image is highlighted with the border , the date of r ecording, the lock and printing status, and the frame number of the image are displayed at the bottom of the screen.
33 Enlarged playback Use the four -way keys of the controller to scroll the image. When scrolling, the arrows in the display will disappear when the edge of the image has been reached. In single-frame playback in Quick View or the playback mode, a still image can be enlar ged for clos- er examination fr om 1.
34 Advanced recor ding ADVANCED RECORDING This section cover the advanced recording features of this camera. Read the basic recor ding sec- tion before moving on to this section. 3. Flash-mode indicator (p. 26) 7. White-balance indicator (p. 58) 8. Camera-sensitivity (ISO) display (p.
35 Macr o Wide-angle position: 0.1 - 1m (3.9 in. - 3.3 ft.) T elephoto position: 1.2 - 2.5cm (3.9 - 8.2 ft.) Super -macro indicator T wo macro modes are available: Super Macr o and standar d macro. Super Macro allows the camera to focus as close as 1cm (0.
The photographer selects the aperture and the camera sets the appropriate shut- ter speed to ensure the correct exposure. When aperture priority is selected, the aperture value on the monitor turns blue and a double arrow indicator appears next to it.
The shutter speed and aperture control more than the exposure. The shutter speed determines how sharp a moving subject is. The aperture controls the depth of field; the area in front of the camera that appears sharp. For more on exposure controls, see the Short Guide to Photography on page 68.
Manual exposure mode allows individual selection of shutter speeds and aper- tures. This mode overrides the exposure system giving the photographer total con- trol over the final exposure. 38 Advanced recor ding Use the up/down keys of the controller to change the shutter speed.
A message is displayed during the exposure. Noise-reduction processing is applied to the image after the exposur e. Noise r eduction can be canceled in section 2 of the setup menu (p. 90). Time photographs can be taken in the manual-exposure mode. Exposures up to thirty seconds can be made.
40 Advanced recor ding Before recor ding, the frame counter shows the maximum time in seconds that can be recorded on the next movie clip. Recording time Frame the pictur e as described in the basic recor ding operation section (p. 22). Press the shutter -release button partway down to set the the focus and exposure.
41 T o adjust the exposure, press the left or right controller key; the exposure-compensation screen appears. Use the left/right keys of the controller to adjust the exposure- compensation value.
42 Advanced recor ding Press the shutter -release button partway down or press the central button of the controller to select the area; the other four areas disap- pear . Only when a focus area has been selected, can the controller be used for other camera operations.
43 Attaching an accessory flash T o extend the versatility of the camera, an accessory flash unit (sold separately) can be used. Always remove the accessory flash when the camera is not in use, and replace the accessory-shoe cap to pr otect the contacts.
44 Advanced recor ding Press the central button of the contr oller to select the highlighted setting; some options open a selection screen. On the P , A, S, and M menu, use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted.
45 Drive mode Image size Quality Auto DSP Digital zoom Single 2272x1704 Standard On Off Drive mode Image size Quality Focus mode Digital zoom Single 2272x1704 Standard Autofocus Off Drive mode Image size Quality Key func.
46 Advanced recor ding The drive modes control the rate and method images are captur ed. The drive mode is set on all menus except the movie menu. With auto recor ding and Digital Subject Programs, the drive mode is r eset to single-frame advance when the exposure-mode dial is moved to another position or the camera is tur ned of f.
47 Used for self-portraits, the self-timer will delay the release of the shutter for approximately ten sec- onds after the shutter -release button is pressed. The self-timer is set on section 1 of the recor ding menus (p. 44). The self-timer can be used to minimize camera shake with long exposur es.
48 Advanced recor ding Using the Continuous-advance modes The continuous-advance drive modes allow a series of images to be captured while holding down the shutter - release button. These drive modes are set in section 1 of the recor ding menus. Drive mode Image size Key func.
49 The continuous-advance drive mode can capture imag es at a rate of approximately 2.5 fps with 2272x1704 images and 2.2 fps with images of other sizes. Focus and exposure is set for each image when the continuous-AF focus mode is used, but the rate of capture is reduced.
Drive mode Image size Key func. Self-timer Single Progressive Bracketing Quality Continuous 50 Advanced recor ding Using the progr essive-capture modes The Progr essive-Capture drive modes continuously recor d images while holding down the shutter -release button.
51 Standard Progr essive Capture recor ds up to the last six images saved in the camera’ s buffer memo- ry; the number of images recorded depends on the file size. The rate of capture is approximately 2.5 fps with 2272x1704 images. Focus and exposure is set for each image when the continuous-AF focus mode is used.
Drive mode Image size Key func. Self-timer Single Progressive Bracketing Quality Continuous This mode makes a three-image bracket of a scene. Bracketing is a method of taking a series of images of a sta- tic subject in which each image has a slight variation in exposure.
53 Number of frames in bracketing series Frame counter When using exposur e compensation (p. 41), the bracketing series will be made in r elation to the compensated exposure. Under extreme conditions, one of the bracketed exposures may be inaccu- rate because it is outside the exposure control range of the camera.
54 Advanced recor ding Changing image size affects the number of pixels in each image. The gr eater the image size, the larger the file size. Choose image size based on the final use of the image - smaller images will be more suitable for web sites whereas lar ger sizes will produce higher quality prints.
55 Fine Standard Economy 61 4 2 3 5 0 14 23 38 67 27 41 53 100 Approximate number of images that can be stored on a 16MB memory card Quality Size 2272 X 1704 1600 X 1200 1280 X 960 640 X 480 Fine Stan.
56 Advanced recor ding Auto DSP Automatic Digital Subject Program Selection can be temporarily dis- abled in the auto-recording menu. When disabled, the program exposure mode is active. If the camera is tur ned off, Automatic Digital Subject Pr ogram Selection is activated.
57 This camera has autofocus and manual focus control. The focus mode is selected separately in the Digital Subject Pr ogram, movie, and P , A, S, and M exposure-mode menus. When using Digital Subject Programs, the focus mode is r eset when the camera is tur ned off.
58 Advanced recor ding Preset white-balance settings must be set befor e the image is taken. Once set, the effect is immediately visi- ble on the LCD monitor . Immediately after selecting the preset white-balance option on the menu, a selection screen is displayed.
59 Custom white-balance allows the camera to be calibrated to a specific lig hting condition. The set- ting can be used repeatedly until r eset. Custom white balance is especially useful with mixed-light- ing or when critical control over color is needed.
60 Advanced recor ding Full-time AF With full-time AF active, the autofocus systems continually focuses to keep the monitor image sharp. This also reduces the autofocusing time when taking pictures. When the camera is set to manual focus, full-time AF is disabled.
61 Flash compensation changes the ratio between the ambient and flash exposures. When using fill- flash to r educe harsh shadows caused by direct sunlight, flash compensation changes the ratio between the highlights and shadows. The flash affects the darkness of the shadows without affect- ing the ar ea illuminated by the sun.
62 Advanced recor ding ISO setting AUTO 50 0.2 - 4.0m (0.7 - 13.1ft.) Flash range (telephoto) 1.2 - 2.5m (3.9 - 8.2ft.) 0.2 - 2.0m (0.7 - 6.6ft.) 1.2 - 1.
63 Color Mode The color mode controls whether a still image is color or black and white. This must be set before the image is recor ded. The color mode is set in section 3 of the P , A, S, and M menus and section 2 of the movie menu (p. 44). The live image r eflects the selected color mode.
64 Advanced recor ding Sharpness: hard Sharpness: soft Sharpness Sharpness accents or softens details in an image in three levels: hard (+), normal, and soft (–). This can be set in section 3 of the P , A, S, and M menus (p. 44). Any changes made are applied to the live image, but may be diffi- cult to see.
65 Custom key function The function assigned to the flash mode button can be selected among the flash mode, drive mode, white balance, focus mode, color mode, and camera sensitivity . This can be set in section 1 of the P , A, S, and M menus (p. 44). The flash mode can also be changed in section 2 of the P , A, S, and M menus.
66 Advanced recor ding Quality (movie) Movies can be recorded at three size and quality combinations: 640x480 Fine, 640x480 Standard, and 320x240 Standard. Image size and quality are the same as those for still images: the lar ger the image size and higher the quality , the lar g er the file size.
67 Movie mode The movie mode option selects the type of movie recor ded. Standard produces a normal movie clip. Night Movie uses high camera sensitivity to recor d under low light levels; camera sensitivity will automatically incr ease in low light. Image quality can be lower with Night Movies because of the higher sensitivity .
68 A short guide to photography A SHORT GUIDE TO PHOTOGRAPHY Photography can be a rewarding pursuit. It is a broad and disciplined field that can take years to master . But the pleasure in making photographs and the joy of capturing a magical moment cannot be compared.
69 The shutter contr ols not only exposure, but also the ability to stop motion. Fast shutter speeds are used in sport photography to stop action. Slow shutter speeds can be used to show the flow of motion such as water cascading over a waterfall. The use of a tripod is recommended with slow shutter speeds.
Press the controller to pause the movie playback; press the controller again to resume the playback. 70 Advanced playback Use the left/right keys of the controller to display the movie.
71 Capturing a movie frame A single frame from a movie clip can be copied and saved as a still image. The copied image has the same image size as the original movie. P ause Rew Fwd V ol During playback, pr ess the center button of the con- troller to pause the movie playback at the point to cap- ture the frame.
72 Advanced playback Press the central button of the controller to select the highlighted setting. Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted. Use the up/down keys to scroll thr ough the menu options.
73 DPOF set Date print – Off – – E-mail copy Index print Delete Format – – – – Copy Lock Slide show Playback – – 5 sec. No Repeat Duration T o delete images on the memory card (p. 75). T o format the memory card (p. 76). T o create an index print with the DPOF order (p.
74 Advanced playback When a marked-frames setting is chosen on a menu, the frame selection screen will appear . This screen allows multiple images to be chosen. The left/right keys of the controller moves the yellow border to select the image. The up key of the controller selects the frame; when selected, an indicator appears next to the image.
75 Deleting permanently erases the file. Once deleted, a file cannot be r ecovered. Care should be taken when deleting images. Single, multiple, or all files on the memory card can be deleted in section 1 of the playback menu (p. 72). The delete option has three settings: Delete The file displayed or highlighted in the playback mode is deleted.
The formatting function is used to erase all data on a memory card. Before formatting a memory card, copy the data to a com- puter or storage device. Locking images will not protect them from being deleted when the card is formatted. Always format the mem- ory card using the camera; never use a computer to format a card.
77 Single, multiple, or all files can be locked. A locked file cannot be deleted by either the playback menu functions or the QV/delete button. However , the formatting function (p. 76) will erase all files on a memory card whether locked or not. Important images should be locked.
78 Advanced playback The copy function in section 1 of the playback menu (p. 72) makes exact copies of image or movie files and can store the copied data on another memory card. E-mail Copy in menu section 3 makes a 640x480 (VGA) JPEG copy of an original still image so that it may be easily transmitted by e-mail.
79 Copy After the copy-completed message is highlighted, a screen indicates the name of the folder containing the copied images; press the central con- troller button to return to the menu. When the image(s) to be copied are selected, a screen with four messages is displayed.
80 Advanced playback Section 2 of the playback menu controls the slide-show function. This function automatically dis- plays all still images and movie clips on the memory card in order . The menu has the following options: Slide Show Slide show Playback Duration Repeat Enter All frames Marked Frames 1 - 60s.
81 Slide show Playback – – 5 sec. No Repeat Duration Press the central button of the contr oller to pause and r estart the slide show presenta- tion. Press the menu button to cancel the presen- tation. The presentation can be viewed without image information.
82 Advanced playback The DPOF-set menu option is used to create an order for standard prints from still images on the memory card. Single, multiple, or all images can be printed. Print orders are cr eated in section 3 of the playback menu (p. 72). The print menu option has four setting s: About DPOF This camera is supported by DPOF™ version 1.
83 When the this-frame or all-frames setting is chosen, a screen appears requesting the number of copies of each image; a maximum of nine copies can be or dered.
84 Advanced playback V iewing images on a television It is possible to view camera images on your television. The camera has a video-out terminal to make the connection using the supplied A V cable. The camera is compatible with the NTSC and P AL standards.
85 The setup menu is used to control the camera’ s functions and operation. The navigating the setup menu section covers the operation of the menu. The section is followed by detailed descriptions of the settings.
86 Setup menu Press the central button of the controller to select the highlighted setting. Once a setting has been selected, the cursor will return to the menu options and the new setting will be displayed. Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted.
87 V ideo output T ransfer mode NTSC Data storage Reset def ault Audio signals V olume – 1 1 1 2 Shutter FX Focus signal LCDbrightness P ower save Inst.Playback Lens acc. Language – 1 min. Off None English File # memor y Folder name Date imprint Off Std.
88 Setup menu Monitor brightness can be adjusted in 11 levels. Brightness can be set individually for viewfinder and direct viewing in the recor ding mode. T ur n the mode switch to the appropriate position before opening the brightness option in section 1 of the setup menu (p.
89 Lens accessory This camera is compatible with the optional Wide-Angle Converter ZCW-300 Kit. This kit contains a 0.75X wide-angle converter , which reduces the focal length of the zoom lens’ wide- angle position giving it the equivalent of a 26mm lens on a 35mm camera.
90 Setup menu Folder name All recor ded images are stored in folders on the memory card. T wo folder -name for- mats are available in section 2 of the setup menu, standard and date. Standard folders have an eight character name. The initial folder is named 100KM006.
91 Date imprinting Every time a still image is recor ded, it is stored with an exif tag that contains the date and time of recor ding as well as shooting information. This information can be viewed with the camera in the Quick View or playback mode, or on a computer with the DiMAGE Viewer software.
92 Setup menu p. 58 White balance Auto p. 65 Custom key function Flash mode p. 60 Full-time AF Off p. 60 Flash compensation 0.0 p. 61 Metering mode Multi segment p. 62 Camera sensitivity (ISO) Auto p. 63 Color mode Natural color p. 64 Sharpness Normal p.
93 p. 80 Playback (Slide Show) All frames p. 80 Duration (Slide Show) 5 seconds p. 80 Repeat (Slide Show) No Playback menu p. 94 V olume 2 p. 88 Auto-power -save period 1 minute p. 89 Lens accessory None p. 89 File number (#) memory Off p. 90 Folder name Standard p.
94 Setup menu V ideo output Camera images can be displayed on a television (p. 84). The video output can be changed between NTSC and P AL in section 4 of the setup menu. North America uses the NTSC standard and Europe uses the P AL standard. Check which standard is used in your region to play back images on your television set.
95 T ransfer mode The data-transfer mode must be specified depending on whether images are transferred to a com- puter or printed directly . The data-storage option must be selected to transfer data from the camera to a computer or when using the DiMAGE Viewer software.
96 Setup menu Frame the subject as described in the basic operation section and pr ess the shutter -release button partway down. Confirm the image has stabilized on the monitor and pr ess the shutter -release but- ton all the way down to take the picture.
97 DATA-TRANSFER MODE Read this section carefully before connecting the camera to a computer . Instructions on using and installing the DiMAGE Viewer software are found in the supplied software manual.
98 Data-transfer mode Connecting the camera to a computer Confirm the battery has sufficient power before connecting the camera to a computer; the full-bat- tery indicator should be displayed on the monitor . The use of the AC adapter (sold separately) is recommended over the use of the battery .
99 When the USB connection is completed, a drive icon, or volume, appears in My Computer or the desktop; the name varies with memory card. When using Windows XP or Mac OS X, a window opens requesting instructions on what to do with the image data; follow the directions in the window .
100 Data-transfer mode Choose the r ecommended search for a suitable driver . Click “Next.” Choose to specify the location of the driver . The browse window can be used to indicate the driver location. The driver should be located in the CD-ROM drive at :Win98USB.
101 The add new hardware wizard will confirm the location of the driver . The letter designating the CD-ROM drive will vary between computers. Click “Next” to install the driver in the system. One of thr ee drivers may be located: MNL VENUM.inf, USBPDR.
102 Data-transfer mode Once the camera is connected to the computer , image files can be accessed by double clicking on icons. Image folders are located in the DCIM folder . The misc. folder contains DPOF print files (p. 82). Files and folders on the memory card can be deleted using the computer .
103 The number in the image file name may not correspond to the frame number of the image. As images are deleted in the camera, the frame counter will adjust itself to show the number of images on the car d and r eassign the frame numbers accordingly .
104 Data-transfer mode Disconnecting the camera Windows Me, 2000 Pr ofessional, and XP Confirm that the access lamp is not lit. T ur n of f the camera and then disconnect the USB cable. T o disconnect the camera, click once on the unplug-or -eject-hardware icon located on the task bar .
105 The hardwar e devices to be stopped will be dis- played. Highlight the device by clicking on it then click “Stop.” Confirm that the access lamp is not lit and then drag the mass-storage device icon and drop it into the trash. T ur n the camera of f, and then disconnect the USB cable.
106 Data-transfer mode Changing the memory car d Windows 98 and 98 Second Edition 1. T urn off the camera. 2. Change the memory card. 3. T urn on the camera to remake the USB connection. Windows Me, 2000 Pr ofessional, and XP Macintosh 1. Stop the USB connection using the unplug-or -eject-hardware routine (p.
107 1. Insert a memory card in the camera and connect it to the computer with the USB cable. Other devices must not be connected to the computer during this procedur e. 2. Right click on the My-computer icon. Select “properties” from the drop-down menu.
Confirm the transfer -mode option in section 4 of the setup menu is set to PictBridge. Connect the camera to a PictBridge compatible printer using the camera’ s USB cable. The larger plug on the cable is connected to the printer . Open the A V out/ USB port cover and insert the smaller plug of the cable into the camera.
109 The number of prints in the print run are displayed as well as the print parameters selected with the menu. See the menu navigation section for mor e information (p. 110). Press the central button of the controller to begin printing, or pr ess the menu button to return to the PictBridge screen.
110 Data-transfer mode Navigating the PictBridge menu Press the central button of the contr oller to select the highlighted setting. Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted.
111 Batch print Index print – – Batch print Index print An index print of all still images on the memory card can be made. The quality and size of the print can be specified with the camera menu. The number of images per page varies with the printer .
The paper size of the print can be specified. Highlight the curr ent page size and press the central button of the controller to open paper -size screen. Use the controller to select the paper size, and pr ess the central button to complete the operation.
113 Data print Data can be printed with the image. The printer -setup option uses the options set with the printer . The date of capture and the file name can be selected for printing.
114 Appendix Problem Symptom Cause Solution The camera will not work. Nothing dis- played on the monitors. The batteries are dead. AA Ni-MH batteries ar e inserted incorrectly .
115 Pictures are not sharp. Pictures are taken indoors or in low-light situ- ations without flash. Slow shutter speeds result in blurred images when the camera is hand-held. Use a tripod, change the camera sensitivity to a higher setting (p. 62), or use the flash (p.
116 Appendix Read this section in its entirety to get the best results from your camera. With proper care, your camera will pr ovide years of service. Camera care • Do not subject the camera to shock or impact. • T ur n off the camera when transporting.
117 LCD monitor care • The LCD monitor is manufactured using high-precision technology and more than 99.99% of the pixels operate pr operly . Less than 0.01% of the monitor pixels are displayed as color or bright points; this is not monitor defect and does not affect the recor ded image.
118 Appendix Memory cards SD Memory Car ds and MultiMediaCar ds are manufactured with precision electronic components. The following may cause data loss or damage: • Improper use of the card. • Bending, dropping, or subjecting the card to impact. • Heat, moisture, and direct sunlight.
119 Befor e important events and jour neys • Check the camera’ s operation; take test pictur es and pur chase spare batteries. • Konica Minolta has no responsibility for any damage or loss incurr ed by equipment malfunction. Copyright • TV program, films, video tapes, photographs, and other materials may be copyrighted.
120 Appendix QuickTime system requir ements T o install QuickTime, follow the instructions in the installer . Macintosh users can download the latest version of QuickTime free of char ge from the Apple Computer web site: http://www .apple.com. V ideoimpression 2 system r equirements Pentium III 450 processor or equivalent.
FCC Compliance Statement Declaration on Conformity Responsible Party: Konica Minolta Photo Imaging U.S.A. Inc. Address: 725 Darlington Avenue, Mahwah, NJ 07430 This device complies with Part 15 of the FCC Rules.
122 Appendix CCD: 1/2.5-type interline primary-color CCD Number of ef fective pixels: 4.0 million T otal number of pixels: 4.2 million Camera sensitivity (ISO): Auto and 50, 100, 200, 400 ISO equivalents. Aspect ratio: 4:3 Lens construction: 13 elements in 10 groups Maximum aperture: f/2.
123 Printing output contr ol: Exif print, PRINT Image Matching II, PictBridge Menu languages: Japanese, English, German, French, Spanish, and Simplified Chinese A V output: NTSC and P AL Batteries: Four AA alkaline or Ni-MH batteries.
© 2004 Konica Minolta Photo Imaging, Inc. under the Ber ne Convention and the Universal Copyright Convention. 9222-2733-11 MS-A406/0406/109678 Printed in Germany 0-43325-53382-2 Konica Minolta Photoworld: www .konicaminoltaphotoworld.com Become a member of the Konica Minolta Photo World today .
An important point after buying a device Konica Minolta DiMAGE Z3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Konica Minolta DiMAGE Z3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Konica Minolta DiMAGE Z3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Konica Minolta DiMAGE Z3 you will learn all the available features of the product, as well as information on its operation. The information that you get Konica Minolta DiMAGE Z3 will certainly help you make a decision on the purchase.
If you already are a holder of Konica Minolta DiMAGE Z3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Konica Minolta DiMAGE Z3.
However, one of the most important roles played by the user manual is to help in solving problems with Konica Minolta DiMAGE Z3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Konica Minolta DiMAGE Z3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
