Instruction/ maintenance manual of the product DiMAGE S414 Konica Minolta
Go to page of 112
9222-2799-11 PR-A212/ME0302 INSTRUCTION MANU AL E.
2 BEFORE Y OU BEGIN Thank you f or purchasing this Minolta digital camera. Please take the time to read through this instruction manual so you can enjo y all the features of y our new camera. Chec k the packing list before using this product. If an y items are missing, immediately contact your camera dealer .
3 FOR PROPER AND SAFE USE Read and understand all warnings and cautions before using this product. Using batteries improperly can cause them to leak har mful solutions, ov erheat, or explode which ma y damage proper ty or cause personal injur y . Do not ignore the follo wing warnings.
4 FOR PROPER AND SAFE USE • Store this product out of reach of children. Be careful when around children not to harm them with the product or par ts. • Do not fire the flash directly into the ey es. It ma y damage eyesight. • Do not fire the flash at vehicle oper ators.
5 This mark on your camera certifies that this camera meets the requirements of the EU (European Union) concerning interference causing equipment regulations. CE stands for Conf ormité Européenne (European Conformity). Digital Camera: Tested To Comply With FCC Standards FOR HOME OR OFFICE USE This device complies with P ar t 15 of the FCC Rules.
6 T ABLE OF CONTENTS The basic operation of this camera is co vered between pages 15 and 42. This section of the manual cov ers the camera par ts, preparation of the camera f or use, and the basic camer a operation for recording, viewing, and deleting images .
7 Basic recording operation ........................................................................................................25 F ocus loc k........................................................................................................
8 T ABLE OF CONTENTS A shor t guide to photograph y ...............................................................................................................66 Movie recording .....................................................................
9 Data-transf er mode...............................................................................................................................92 System requirements ................................................................................
10 NAMES OF P ARTS * This camera is a sophisticated optical instrument. Care should be taken to keep these surf aces clean. Please read the care and storage instructions in the back of this manual (p . 107). CAMERA BOD Y Data panel (p . 13) Shutter-release button Lens* Self-timer/ Remote-control lamp (p .
11 Card-slot door (p . 18) The USB por t and A V -out terminal are located behind the card-slot door . Viewfinder* (p . 12) LCD monitor* (p . 14) Menu button Flash mode/Magnification button (p . 30, 41) DC terminal cover (p . 18) Access lamp QV/ Delete button (p .
12 NAMES OF P ARTS MODE DIAL A uto-recording mode (p . 22, 42) Multi-function recording mode (p . 52) Playbac k mode (p . 38, 70) Movie-recording mode (p . 68) Setup mode (p . 84) Data-transf er mode (p. 92) VIEWFINDER F ocus lamp (g reen) Flash lamp (orange) F ocus fr ame This dial gives direct and easy access to the camera’ s major modes.
Fr ame counter (p . 45) Digital-subject-program icons (p . 28) 13 DA T A P A N E L Digital-subject-program indicators (p . 28) Exposure-compensation indicator (p . 50) Camera-sensitivity indicator (p . 62) Spot-metering indicator (p. 63) Battery-condition indicator (p.
14 NAMES OF P ARTS LCD MONIT OR DISPLA Y c. Flash-mode indicator (p . 30) e. Contrast-compensation displa y (p. 65) f. Filter display (p . 65) g. Exposure-compensation display (p . 50) h. White-balance indicator (p . 60) n. Camera-sensitivity (ISO) displa y (p.
15 Using your thumb and inde x finger , pinch the outside tabs of the lens cap to remov e or attach. Always replace the lens cap when the camera is not in use. Attach the camera strap to the strap e yelets as shown. Make sure the neck strap passes through the loop of the lens-cap strap .
16 GETTING UP AND RUNNING CHANGING BA TTERIES Inser t the batteries. Make sure the positive and negativ e battery terminals are or iented as illustrated on the diagram in the battery chamber . This digital camera uses f our AA-size alkaline or Ni-MH batteries.
17 BA TTER Y CONDITION INDICA TOR Full-battery Icon - the batter ies are fully charged. This icon is display ed f or fiv e seconds on the monitor when the camera is turned on. The icon remains on the data panel. Blinking low-battery icon - when display ed on the data panel with no other icons, pow er is insufficient for camera oper ation.
18 GETTING UP AND RUNNING EXTERNAL PO WER SUPPLIES (SOLD SEP ARA TEL Y) CHANGING THE COMP A CTFLASH CARD The AC Adapter allo ws the camera to be powered from an electrical household outlet. The A C Adapter is recommended when the camera is interf aced with a computer or during per iods of heavy use.
1 2 3 4 19 Slide the card-slot door release down to open the card-slot door (1). To eject a CompactFlash card, press the card-eject lev er (2). The card can now be pulled out. T ake care when removing the card as it becomes hot with use. Inser t the memor y card into the card slot until the card-eject lev er pops out (3).
20 GETTING UP AND RUNNING SETTING THE DA TE AND TIME After initially inser ting a memor y card and batteries, the camera’ s clock and calendar m ust be set. When images are recorded, the image data is sav ed with the date and time of recording. Depending on the region, the menu language ma y also hav e to be set.
Setup Basic Custom1 Custom2 Reset default Date/Time set Date format Video output – – MM/DD/YYYY NTSC 21 Use the right key to highlight the custom 2 tab at the top of the menu. Use the down k ey to highlight the date/time-set menu option. Press the center of the controller to display the date/time setting screen.
22 AU T O-RECORDING MODE - BASIC OPERA TION AU T O-RECORDING MODE BASIC OPERA TION This section cov ers the basic operation of this camera. Thoroughly f amiliarize yourself with the operations in this section bef ore moving on to the other sections in the manual.
23 SETTING THE CAMERA T O RECORD IMA GES A UT OMA TICALL Y Tu rn the mode dial to automatic recording (1); all camera operations are now fully automatic. The autofocus, e xposure, and imaging systems will work together to bring beautiful results effortlessly .
24 AU T O-RECORDING MODE - BASIC OPERA TION USING THE ZOOM LENS This camera is equipped with a 7.15 to 28.6mm optical zoom. This is equivalent to a 35 - 140mm z oom lens on a 35mm camera. In 35mm photography , focal lengths belo w 50mm are referred to as wide-angle; the angle of view is larger than that of the human ey e.
25 BASIC RECORDING OPERA TION Press the shutter-release button partway do wn (1) to lock the f ocus and exposure . • When the focus is set, an AF sensor will briefly appear on the liv e image to indicate the point of focus . • The focus signals (p .
26 AU T O-RECORDING MODE - BASIC OPERA TION FOCUS LOCK The focus-loc k function is used when the subject is off-center and outside the focus fr ame. Focus lock ma y also be used when a special focusing situation pre v ents the camera from focusing on the subject.
27 FOCUS SIGNALS SPECIAL FOCUSING SITU A TIONS This digital camera has a quick, accur ate autofocusing system. The focus icon in the lower right corner of the LCD monitor and the green f ocus lamp next to the vie wfinder indicate the focus status . The camera ma y not be able to f ocus in cer tain situations.
The digital-subject-program b utton (1) optimizes the camera’ s e xposure, white-balance, and image-processing systems for v arious conditions and subjects. Pressing the subject-program b utton cycles through the modes: macro, por trait, landscape, night portrait, text, macro & te xt, and the original exposure mode.
29 TEXT - for the crisp reproduction of b lack te xt or line ar t on white backgrounds . The flash mode is set to flash cancel (p . 30). Fill-flash can be used. Use a tripod to eliminate camera shake and ensure the sharpest images. NIGHT PORTRAIT - for deep , subtle night scenes.
30 Flash cancel - the flash will not fire. Use flash cancel when flash photograph y is prohibited, natural light is desired to illuminate the subject, or the subject is bey ond the flash range. The camera- shake w ar ning may appear when flash cancel is selected (p .
31 If the shutter speed falls belo w the point where the camera can be saf ely hand held, the camera- shake w ar ning will appear on the LCD monitor and the orange f ocus lamp will blink slowly . Camera shake is slight b lurring caused by subtle hand motion and is more pronounced at the telephoto setting of the lens than at the wide-angle setting.
The drive modes control the rate and method images are captured. Icons indicating the selected drive mode appear on the data panel and LCD monitor . To change the drive mode, simply press the drive-mode b utton (1) on the back of the camera until the desired mode is displa yed.
33 Used for self-portraits, the self-timer will dela y the release of the shutter for appro ximately ten seconds after the shutter-release button is pressed. The self-timer is set with the dr ive-mode b utton (p . 32). With the camera on a tripod, compose the picture as described in the basic recording operation section (p .
34 AU T O-RECORDING MODE - BASIC OPERA TION REMO TE CONTR OL (SOLD SEP ARA TEL Y) The IR Remote Control RC-3 allows remote camera oper ation up to 5m (16 ft.) awa y . The remote control unit can be used in movie recording (p . 68). Place the camera on a tripod, and set the drive mode to self-timer / remote control (p .
The continuous-adv ance drive mode allows a series of images to be captured while holding down the shutter-release button. Continuous advance acts like a motor driv e on a film camera. The number of images that can be captured at one time and the rate of capture depend on the image-quality and image-size setting.
Compose the picture as described in the basic recording operation section (p. 25). Press the shutter-release button partway do wn (1) to lock the e xposure and focus f or the series. Press and hold the shutter-release button all the wa y down (2) to mak e the brack et series; three consecutive images will be captured.
37 LCD monitor off The display b utton controls the LCD monitor display . The displa y cycles to the next position each time the button is pressed: standard display , focus fr ame only , real-time histogram, liv e image only , and monitor off. The number of screens and their formats can be changed in the basic section of the setup menu (p .
38 PLA YBA CK - BASIC OPERA TION Images can be viewed in the Quic k View or pla yback modes . This section covers the basic oper ations in both modes. The pla yback mode has additional functions , see page 70. To view images from the pla yback mode, turn the mode dial to the playbac k position.
39 To view the histogr am of the display ed still image, press the up ke y . The histogram shows the luminance distribution of the image from b lack (left) to white (right). The 224 ver tical lines indicates the relative propor tion of that light value in the image .
40 Full display Index pla yback In index pla yback, the left/right k eys of the controller will mov e the yellow border to the ne xt or the previous image .
41 ENLARGED PLA YBACK In single-frame pla yback, a still image can be enlarged up to 3.5X in 0.2X increments f or closer e xamination. 640 X 480 size images can only be enlarged between 1.2X and 2.0X. The maximum enlargement of 1024 X 768 digital zoom images is 3.
42 AU T O-RECORDING MODE - ADV ANCED OPERA TION NA VIGA TING THE A UT O-RECORDING MODE MENU In auto-recording mode, press the menu b utton (1) to activate the menu. The menu button also turns off the menu after settings are made. The four-wa y ke ys of the controller (2) are used to move the cursor in the menu.
Settings made with the auto-recording menu will remain in effect until changed or the camer a is reset to its default settings (p . 90). Image size - T o set the pixel resolution of the images. Image size aff ects the size of the image file. Image quality - T o set the rate of compression of the images.
44 AU T O-RECORDING MODE - ADV ANCED OPERA TION Changing image size aff ects the number of pixels in each image . The greater the image size, the larger the file siz e. Choose image size based on the final use of the image - smaller images will be more suitable f or web sites whereas larger sizes will produce higher quality prints.
45 TIFF Fine Standard Economy 123 1 3 61 2 1 7 3 4 11 19 26 42 17 27 33 48 Appro ximate number of images that can be stored on a 16MB memor y card. Quality Size 2272 X 1704 1600 X 1200 1280 X 960 640 X 480 TIFF Fine Standard Economy 12MB 5.7MB 3.7MB 1.
46 AU T O-RECORDING MODE - ADV ANCED OPERA TION V oice memo allows a five or fifteen second audio tr ack to be recorded with a still image. The function is activated and the length of the recording time is set on the auto-recording mode men u (p. 42).
47 The date of recording can be printed directly on the image. The imprinting function must be activated bef ore the image is taken. Once activated, the date will contin ue to be imprinted until the function is reset; a yellow bar is displa yed behind the frame counter on the monitor to indicate date imprinting is active.
2272 X 1704 1600 X 1200 1280 X 960 48 AU T O-RECORDING MODE - ADV ANCED OPERA TION DIGIT AL ZOOM Assisting the optical zoom is a 2.2X digital zoom. The effect of the digital zoom doub les the power of the telephoto position of the optical zoom giving the equiv alent of a 308mm lens on a 35mm camera.
49 INST ANT PLA YBACK Off 2 sec 10 sec Instant pla yback is disabled. The captured image will be displa yed f or two or ten seconds. While dis- pla yed, the image can be deleted bef ore being sav ed. : delete : store A uto Press the controller to delete the image.
50 AU T O-RECORDING MODE - ADV ANCED OPERA TION adjust set To adjust the exposure , press the e xposure-compensation b utton (1). The e xposure compensation screen will appear . Use the left/right keys of the controller (2) to adjust the exposure-compensation v alue .
51 WHA T IS AN EV? WHA T IS A ST OP? Sometimes the camera’ s e xposure meter is deceived b y cer tain conditions. Exposure compen- sation can be used in these situations. For example , a very bright scene, such as a snowy land- scape or a white sandy beach, can appear too dark in the captured image.
52 MUL TI-FUNCTION RECORDING MODE MUL TI-FUNCTION RECORDING MODE AU TO FOCUS AREAS AND CONTROL In the multi-function recording mode, the controller selects the f ocus area used. The wide f ocus area and focus area selection allo w flexibility in a v ariety of situations.
53 The focus area selection controls which spot f ocus area is activ e. This function can be used f or off- center subjects or to single out an individual subject from a group . Once a spot focus area is selected, it will remain activ e e ven after the picture has been taken.
54 MUL TI-FUNCTION RECORDING MODE Activate the recording-mode menu with the men u button. The basic tab at the top of the menu will be highlighted. Use the left/right keys of the controller to highlight the appropriate menu tab; the menus will change as the tabs are highlighted.
Custom 55 Refer to the auto-recording mode section f or details on image size (p . 44), image quality (p. 44), voice memo (p . 46), date imprinting (p.
The photographer selects the aperture and the camera sets the appropriate shutter speed to ensure correct exposure . When aper ture prior ity is selected, the aper ture value on the monitor turns blue and a double arro w icon appears next to it.
Manual e xposure mode allows individual selection of shutter speeds and aper tures. This mode ov errides the exposure system giving the photographer total control o ver the final e xposure. The shutter speeds can be changed in half stop increments between 1/1000 and 4 seconds.
Bulb photographs can be tak en in the manual-exposure mode (M) (p . 57). Exposures up to fifteen seconds can be made by pressing and holding the shutter-release button. The use of a tr ipod is recommended. The camera’ s e xposure system cannot be used to calculate bulb e xposures; a separate light meter is recommended.
59 FOCUS MODES This camera has autof ocus and manual focus control. The focus mode is set in the basic section of the multi-function recording mode menu (p .
Preset white-balance settings must be set bef ore the image is taken. Once set, the effect is immediately visible on the LCD monitor . The built-in flash can be used with preset white-balance settings, b ut will create a pinkish or blueish cast with the fluorescent and tungsten settings.
61 Custom-white-balance function allows a photogr apher to calibrate the camera to a specific lighting condition. The setting can be used repeatedly until reset. Custom white balance is especially useful with mixed-lighting conditions or when critical control ov er color is needed.
62 MUL TI-FUNCTION RECORDING MODE CAMERA SENSITIVITY - ISO FLASH RANGE AND CAMERA SENSITIVITY The flash range is measured from the CCD . Because of the optical system, the flash range is not the same at the lens’ wide-angle position as it is at the telephoto position.
63 The icons indicating the metering modes are display ed on the monitor . The metering mode is set in the custom 1 section of the multi-function recording mode menu (p . 54). METERING MODES FULL-TIME AF With full-time AF active , the autofocus systems continually f ocuses to keep the monitor image sharp .
64 MUL TI-FUNCTION RECORDING MODE EXPOSURE BRA CKETING INCREMENT In multi-function recording mode, three br acketing steps can be selected: 0.3 Ev , 0.5 Ev , 1.0 Ev . The larger the number , the greater the diff erence in exposure betw een the images in the brack eted series.
65 Changes in color , sharpness, and contrast can be made using the custom 2 section of the multi- function recording mode menu (p . 54). The shar pness, contrast and filter imaging controls giv e photographers the ability to maximiz e the image information at the scene.
66 A SHORT GUIDE TO PHO TOGRAPHY Photograph y can be a rew arding pursuit. It is a broad and disciplined field that can take years to master . But the pleasure in making photographs and the jo y of capturing a magical moment cannot be compared. This guide is an introduction to some basic photographic principles.
67 The shutter controls not only exposure , but also the ability to stop motion. F ast shutter speeds are used in spor t photograph y to stop action. Slow shutter speeds can be used to show the flow of motion such as w ater cascading ov er a waterf all.
68 MO VIE RECORDING This camera can record up to sixty seconds of digital video with sound. The motion JPEG image is 320 X 240 pixels (QV GA). The effectiv e image area is 284 X 211 pixels; two thin lines will appear to the left and right of the image when play ed back.
69 The RC-3 remote control (sold separately) can be used to record movie clips up to 5m (16ft) aw ay . Simply point the remote control toward the camera and use the release or dela y button to star t and stop the recording.
70 PLA YBA CK MODE - AD V ANCED OPERA TION PLA YBA CK MODE - AD V ANCED OPERA TION The basic functions in this mode are described in the basic playbac k section on pages 38 through 41. This section cov ers how to pla y back movie clips and v oice memos as well as the adv anced functions on the playbac k menu.
Playbac k time is display ed on a bar at the top of the image. The display returns to Quick View or the playbac k mode when the movie clip finishes. Pressing the controller during playbac k pauses the movie clip; pressing the controller again resumes the playback.
72 PLA YBA CK MODE - AD V ANCED OPERA TION Play Basic Custom1 Custom2 Delete Lock Index f ormat – – 9 frames Activate the pla yback-mode menu with the men u button.
73 1 Copying to camer a memor y . Refer to the f ollowing sections f or descriptions of the menu options and their settings. Choosing “Y es” will e xecute the oper- ation, “No” will cancel it. Ye s No F or inf ormation on frame-selection screens, see page 74 .
74 PLA YBA CK MODE - AD V ANCED OPERA TION FRAME-SELECTION SCREEN The left/right keys of the controller mov e the y ellow border to select the image. The up ke y of the controller selects the frame; when selected, an icon will appear next to the image .
75 VIEWING IMA GES ON A TELEVISION It is possible to vie w camera images on your tele vision. The camera has a video-out terminal to make the connection using the supplied A V cable. The camera is compatib le with the NTSC and P AL standards. The video-output setting can be chec ked and set in the custom 2 section of the setup menu (p .
76 PLA YBA CK MODE - AD V ANCED OPERA TION Single, multiple , or all files in a folder can be deleted with the pla yback-mode menu. Before an image file is deleted, a confirmation screen will appear ; choosing “Y es” will e x ecute the operation, “No” will cancel it.
77 Single, multiple , or all files in a folder can be loc ked. A lock ed file cannot be deleted by either the playbac k-mode menu functions or the QV/delete button. Impor tant image files should be locked. T o lock files in other f olders, the f older must first be selected in the custom 1 section of the setup menu (p .
78 PLA YBA CK MODE - AD V ANCED OPERA TION The custom 1 section of the playbac k-mode menu controls the slide-show function. This function automatically displays all still images in a f older in order . SLIDE SHO W Fr ame count- down / total num- ber of images in the presentation.
79 To select all the images in the folder to be displa yed in the slide-show presentation. Slide show Menu options Playbac k Duration Settings Enter Repeat All frames Marked Fr ames 1 - 60s. Y es / No To select specific images in the folder to be displa yed in the slide-show presentation.
80 PLA YBA CK MODE - AD V ANCED OPERA TION The print menu option is used to set an order for standard prints from images in a specific f older . Single, multiple , or all images can be printed. If a CompactFlash card has multiple f olders, a printing file must be created f or each folder .
81 When the this-frame or all-frames setting is chosen, a screen will appear requesting the number of copies of each image; a maximum of nine copies can be ordered.
Press the center of the controller to continue or the menu b utton to cancel the copy operation. After the copy-completed message is highlighted, a ne w screen will appear to indicate the name of the new f older containing the copied images; press the controller to retur n to the menu.
83 If too many images ha ve been selected, a warning will appear and the copy routine will be canceled. Divide the number of images into two or three batches . The copy-unsuccessful message will appear when one or all of the images could not be copied.
84 SETUP MODE NA VIGA TING THE SETUP MENU To access the menu, simply turn the mode dial to the setup position. The four-wa y ke ys of the controller (1) are used to mov e the cursor in the menu.
85 Choosing “Y es” on the confirmation screens will ex ecute the operation, “No” will cancel it. Ye s No On the date/time setting screen, use the left/right keys of the controller to select the year , month, da y , hour, or minute. The up/down ke ys are used to change the value.
86 SETUP MODE LCD MONIT OR BRIGHTNESS The brightness of the LCD monitor can be set in five le vels from 1 (low) to 5 (high). When this option is selected, the live image is displa yed behind the men u. As each setting is highlighted, the monitor will adjust accordingly; the controller must be pressed to set the highlighted lev el.
87 LANGU A GE The language used in the menus can be changed. The language is selected in the basic section of the setup menu (p . 84). DISPLA Y MODE Standard display Focus fr ame only Live image only Real-time histogram Scale Grid Setup Basic Custom1 Custom2 LCDbrightness For mat Pow e r save Language Display mode Std.
88 SETUP MODE FILE NUMBER (#) MEMOR Y When file number memory is selected, if a new folder is created, the first file stored in the f older will hav e a number one greater than the last file sa ved. If the file number memory is disabled, the image file name will hav e a number one greater than the last image sa ved in the f older .
89 SELECT FOLDER This option allows the selection of e xisting folders . All images recorded will be placed in the selected f older if the f older-name option is set to standard f or m. In quick view or pla yback mode , only the images in the selected folder can be vie wed or edited.
90 SETUP MODE Image quality RESETTING THE CAMERA This function affects all modes . When selected, a confir mation screen will appear; choosing “Y es” resets the follo wing functions and settings, “No” cancels the oper ation.
91 A udio signals File number memory 1 Off Shutter FX 1 LCD monitor brightness A uto-po wer-sav e period 3 1 minute 86 86 89 89 88 Display mode Standard, focus fr ames only , real-time histogram, liv e image only 87 F older name Standard 88 V olume 2 89 DA TE AND TIME SETTING It is impor tant to accurately set the clock.
92 DA T A-TRANSFER MODE DA T A-TRANSFER MODE Read this section carefully before connecting the camer a to a computer . Details on using and installing the DiMAGE Viewer software are f ound in the supplied software man ual.
93 CONNECTING THE CAMERA T O A COMPUTER Star t up the computer . The computer must be turned on before connecting the camera. Inser t the CompactFlash card into the camera. Confirm that the correct card is in the camera. T o change the CompactFlash while the camera is connected to a computer , see page 102.
94 DA T A-TRANSFER MODE When the camera is properly connected to the computer , a drive icon, or v olume, will appear . When using Windows XP or Mac OS X, a window will open requesting instructions on what to do with the image data; follow the directions in the window .
95 The driver needs only to be installed once. If the dr iver cannot be installed automatically , it can be installed manually with the operating system’ s add-new-hardware wizard; see the instructions on the f ollo wing page.
96 DA T A-TRANSFER MODE Choose the recommended search for a suitab le driver . Click “Ne xt. ” Choose to specify the location of the driver . The browse window can be used to indicate the driver location. The driver should be located in the CD-ROM drive at :Win98USB .
97 The add new hardw are wizard will confir m the location of the driver . Click “Next” to install the driver in the system. One of three drivers ma y be located: MNL VENUM.inf, USBPDR.inf , or USBSTRG.inf. The letter designating the CD-ROM drive will v ary between computers.
98 DA T A-TRANSFER MODE Once the camera is connected to the computer , image and audio files can be accessed by doub le clicking on icons. Image folders are located in the DCIM folder . T o copying images and audio recordings, simply dr ag and drop the file icon into a location in the computer .
99 Image and audio file names begin with “PICT” follo wed by a f our-digit file number and a tif , jpg, mov , or thm extension. V oice-memo audio files hav e a wa v extension and the file name corresponds to its image file.
100 DA T A-TRANSFER MODE DISCONNECTING THE CAMERA FROM THE COMPUTER Windows Me , 2000 Prof essional, and XP Confirm that the access lamp is not lit. T ur n off the camera and then disconnect the USB cable. To disconnect the camera, click once on the unplug-or-eject-hardw are icon located on the task bar .
101 The hardware de vices to be stopped will be display ed in the unplug-or-eject-hardware window . Highlight the device b y clicking on it then clic k “Stop . ” Confirm that the access lamp is not lit and then drag the mass-storage de vice icon and drop it into the trash.
102 DA T A-TRANSFER MODE CHANGING THE COMP ACTFLASH CARD - D A T A-TRANSFER MODE Windows 98 and 98 Second Edition 1. T urn off the camera. 2. Change the CompactFlash card. 3. T urn the mode dial to the data-transfer position to remake the USB connection.
103 Q UICKTIME SYSTEM REQUIREMENTS IBM PC / A T Compatible P entium-based computer Windows 95, 98, 98SE, NT , Me, or 2000 Prof essional. 32MB or more of RAM Sound Blaster or compatible sound card DirectX 3.0 or later recommended QuickTime is used f or viewing mo vie clips and playing v oice-memo audio files.
Shutter will not release. “000” is dis- pla yed on the frame counter . CompactFlash card is full and unable to store an image at the image-quali- ty or image-size setting on the camera. Inser t a new CompactFlash card (p . 18), delete some images (p .
While using flash, the pic- tures are too dark. The subject is bey ond the flash range (p . 62). Mov e closer to the subject or change the camera sensitivity to a higher setting (p . 62). Problem Symptom Cause Solution Shutter speed and aper ture combination is e xtremely under or over- e xposing the live image.
106 APPENDIX 1. Inser t a memory card in the camera and connect it to the computer with the USB cable . Other devices m ust not be connected to the computer during this procedure. 2. Right click on the My-computer icon. Select “properties” from the drop-down men u.
107 CAMERA CARE • Do not subject the camera to shock or impact. •T urn off the camera when transpor ting. • This camera is neither waterproof nor splashproof. Inser ting or removing batteries or the CompactFlash card, or operating the camera with wet hands ma y damage the camera.
108 APPENDIX LCD MONIT OR CARE • Although the LCD monitor is manuf actured using high precision technology , there may occasionally be a lack of color or bright points on the LCD monitor . • Do not apply pressure to the surface of the LCD monitor; it may be permanently damaged.
109 BA TTERIES • Battery performance decreases with temperature. In cold environments, we recommend k eeping spare batteries in a warm place, such as the inside of a coat.
110 APPENDIX TECHNICAL SPECIFICA TIONS Number of eff ective pix els: 4.0 million CCD: 1/1.8-type interline pr imar y-color CCD with a total of 4.1 million pix els.
111 Batteries: 4 AA Ni-MH or alkaline batteries. Ni-MH batteries are recommended ov er alkaline. Batter y perf or mance (recording): Appro ximately 160 frames.
9222-2799-11 PR-A212/ME0302 Printed in Ger many © 2003 Minolta Co ., Ltd. under the Berne Conv ention and the Univ ersal Copyright Conv ention. 0-43325-53187-3 Minolta Customer Support: www .
An important point after buying a device Konica Minolta DiMAGE S414 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Konica Minolta DiMAGE S414 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Konica Minolta DiMAGE S414 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Konica Minolta DiMAGE S414 you will learn all the available features of the product, as well as information on its operation. The information that you get Konica Minolta DiMAGE S414 will certainly help you make a decision on the purchase.
If you already are a holder of Konica Minolta DiMAGE S414, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Konica Minolta DiMAGE S414.
However, one of the most important roles played by the user manual is to help in solving problems with Konica Minolta DiMAGE S414. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Konica Minolta DiMAGE S414 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
