Instruction/ maintenance manual of the product VIDEOMATE 2030P Kodak
Go to page of 18
V IDEO M ATE 2030/2030 P Video Slide Projector Instruction Manual The W orld Leader in Image Quality.
2 Table of Contents 3 Product Overview 4 Safety Precautions 5 Voltage Selection 7 Installation 9 Slide Tray Installation 1 1 Lamp/Fuse Replacement 1 3 Troubleshooting 1 5 Specifications 1 6 Appendix 1.
3 Product Overview Product Overview Universities, boardrooms, and conventions have the common goal of effective information communication. T oday’ s individual is continually being bombarded by sophisticated media presentation. T o compete ef fectively for his attention (and retention) one must utilize similar techniques.
4 7 Safety Precautions Safety Precautions For safety , before connecting the projector to the main, ensure that the voltage selector is set to your main voltage and the required fuse is fitted. An incorrectly adjusted main voltage can damage the projector .
5 Voltage Selection Voltage Selection Check voltage setting. The Navitar VideoMate will be exported throughout the world to countries with differing mains voltages. The projectors are already set during manufacture to a fixed main voltage. 100-200V mains: Shipments to countries with 100 or 200V mains will be equipped with a 5A fuse.
6 V oltage Selector Tray Positioning Index Mark Lock Ring Alignment Mark Fuse Holder Voltage Selection.
7 Installation Installation Before installing please review precautions. For those users familiar with both the operation of 35mm slide projector and their own video displays, the following is an abbreviated start-up procedure. 1. Check the voltage setting before powering on.
8 Installation 9. T o shut down the system, hold down the select bar and rotate the slide tray to the “0” index position. Set the power switch to “off”. 10. For instructions regarding setting up slide tray changing lamps, etc., refer to the appropriate section of the manual.
9 Slide Tray Installation Slide Tray Set-Up This system was designed to permit usage of prepared presentations without reorientation of the slides in the tray . Y our new Navitar VideoMate will accept Kodak Ektapro 80, Kodak Ektagraphic 80 for holding 80 slides with a maximum slide mount thickness of 3.
10 Slide Tray Installation Slide Tray Removal T o remove the tray from the projector without losing slides: 1. Hold the selector bar down and rotate the tray back to the zero index position. 2. Lift the tray at a point opposite the index mark. Slide Tray Jam The tray may jam if a damaged slide is caught in the gate.
11 Lamps/Fuse Replacement Lamps The VideoMate will function with either of the following 82 volt or 85 watt lamps. One provides a higher color temperature, with the other exhibits a much longer life. Do not use 82 volt, 25-300 watt slide projection lamps or your equipment will suffer severe damage.
12 4. Reverse the procedure to insert a new lamp (make sure the new lamp is properly seated). 5. Lock the new lamp in place with wire bail. Fuses Always switch off the projector and unplug the main lead before replacing a fuse. Avoid the risk of fire, replace only with a fuse of same type and rating.
13 Troubleshooting Troubleshooting Symptom #1: After switching on, projector is not operable. Possible Cause: 1. All equipment not “powered up”. Check outlets and individual unit (monitor , video projector , etc.). 2. Check input voltage selector .
14 Symptom #4 Image too dark or too light. Possible cause: 1. Illumination level inadequate. Set knob “I” as required. 2. Monitor not adjusted properly . Symptom #5 Image not sharp. Possible cause: 1. Adjust focus knob. 2. Illumination level is too high or too low .
15 s n o i t a c i f i c e p S a r e m a C e c i v e D p u - k c i PD C C r e f s n a r T e n i l r e t n I " 2 / 1 t n u o C l e x i P) V ( 2 8 5 x ) H ( 2 5 7 r e t l i F r o l o Cc i a s o M r.
16 Appendix Appendix Due to transportation, the image position might shift from the factory setting. T o correct this shift: 1. Remove the two plugs as shown in the figure below: 2. Using the Phillips screw driver , rotate screw #1 to adjust the vertical position and screw #2 to adjust the horizontal position.
17 Warranty 1 Year Parts /1 Year Labor This product is warranted to be free from defects in material and workmanship for a period of five years from the date of invoice to the original purchaser . If during the warranty period the product is found to be defective, it will be repaired or replaced at the facilities of Navitar .
18 Navitar , Inc. 200 Commerce Drive Rochester , NY 14623 (716) 359-4000 phone (716) 359-4999 fax Internet http://navitar .com/ e-mail info@navitar .com.
An important point after buying a device Kodak VIDEOMATE 2030P (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kodak VIDEOMATE 2030P yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kodak VIDEOMATE 2030P - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kodak VIDEOMATE 2030P you will learn all the available features of the product, as well as information on its operation. The information that you get Kodak VIDEOMATE 2030P will certainly help you make a decision on the purchase.
If you already are a holder of Kodak VIDEOMATE 2030P, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kodak VIDEOMATE 2030P.
However, one of the most important roles played by the user manual is to help in solving problems with Kodak VIDEOMATE 2030P. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kodak VIDEOMATE 2030P along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
