Instruction/ maintenance manual of the product UL-2 Anton/Bauer
Go to page of 12
ULTRALIGHT 2 ( UL-2 ) OWNER’S MANUAL.
.
TO REMOVE / REPLACE BULB NOTE: Only MR-16 type bulbs sho uld be used with the UL2. 1. Pull out on the Thumb Tabs of the Head M odule. 2. Swing Hood open. 3. Remove and replace bulb as necessar y. 4. Close Head Module, insuring that it “clicks ” closed.
INTRODUCTION The Ultraligh t 2 (UL2) is a n extremel y compact, sup er lightwe ight version of the orig inal Ultra light system, designed specific ally for o n-camer a lighting applicatio ns. The Ultra light 2 inco rporate s many uniq ue feature s includi ng: • Included with a AB-60, wide angle bulb.
5/64 Hex Wrench Shoe Sleeve Shoe Mount Thumbwheel Set Screw Be sure the Shoe Sleeve is completely inside the light, otherwise the light may swing back & forth. ¼-20 STUD MOUNT APPLICATION The Ultralight 2 is shipped standard with ¼ -20 Stud Mount for attachi ng to the camera handle.
Stud Mount Application 1/4-20 Screw ACCESSORIES UL2 WEDGE The UL2 Wedge is developed specifically for use with the Anton/Bauer Ultralight 2 on-ca mera light. The UL2 Wedge provides the Ultralight 2 with an additional 20º of down angle lighting for shooting extreme close up camera shots (less than 3 feet).
When properly fitted, the slot in the tab will align with a screw in the center of the hood. The ta b insertion requires a slight force. If the filter assembly is too loose and does not stay in place, bend each side of the tab in opposite dire ctions as show n to provide sufficient holdi ng friction.
UL-SOFT B OX The UL-Soft Box mounts easily to any Ultralight Head Module to sof ten and diffuse light output. The UL-Soft Box is collapsible allowing eas y storage or can fold and swing awa y while remaining on the Ultralight until needed.
BULB SELECTION AND OPERATION Bulbs used by the Ultralight 2 are T ype MR16, tungsten-halogen bul bs. Spot or flood bulbs of any light distribution angle may be used. The Ultralight 2 offers the greatest versatility with the following low voltage bulbs.
WARRANTY IMPORTANT: WARRANTY REGISTRAT ION CARD MUST BE MAILED WITHIN 10 DAYS OF PURCHASE TO QUALIFY FO R THIS WARRANTY. Pro per registration will also enabl e us to send you important update information. We must have the warrant y registration card on file at our CUSTOM ER SERVICE DEPARTMENT t o establish warranty.
.
The worldwide standard The following are registered trademarks of Anton/Bauer, Inc.: ACS, Anton/Bauer, Anton/Bauer Logo, Au tomatique, ComPac, Gol d Mount,HyTRON, Impac, InterActive, InterActive 2000 .
An important point after buying a device Anton/Bauer UL-2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Anton/Bauer UL-2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Anton/Bauer UL-2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Anton/Bauer UL-2 you will learn all the available features of the product, as well as information on its operation. The information that you get Anton/Bauer UL-2 will certainly help you make a decision on the purchase.
If you already are a holder of Anton/Bauer UL-2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Anton/Bauer UL-2.
However, one of the most important roles played by the user manual is to help in solving problems with Anton/Bauer UL-2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Anton/Bauer UL-2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center