Instruction/ maintenance manual of the product QUAD 2702 Anton/Bauer
Go to page of 15
PowerCharger DUAL and QUAD OWNER’ S MANUAL.
TABLE OF CONTENTS INTRODUCT ION ............................................................................................. 1 STANDARD F EATURES ................................................................................. 1 DISCHARGE OPTION ...
1 INTRODUCTION This Anton/Bauer Inte rActive 2000 PowerCharger represents over 25 years of Ant on/Bauer technology and experience in a tota lly new portable power system .
2 IMPORTANT NOTICE READ ALL INSTRUCTIONS, NOTES AND OPERATING SPECIFICATIONS FULLY BEFORE OPERATING THIS EQUIPMENT. This unit was packaged at the factory to arrive intact at its destination. If there is any damage to the packaging or the unit when received, please notify the carrier immediately.
3 SAFEGUARDS Power Sources: This unit was designed to operate at mains voltages from 90 to 250 Volts AC, 50-60 Hz. Risk of Electrical Shock: Refer servicing to quali fied service personnel. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
4 Charging As with all Anton/B auer chargers, charging with an Int erActive 2000 PowerC harger is fully automatic. Mount any applicable ba ttery to any open Gold Mount position on the charger and the Po werCharger will automatically determine the appropriate ch arge routine and execute it.
5 Three Stage Charging Methodology In general, the PowerCharger will deliv er a three stage charge routine to each battery. 1. Stage One will deliver a high rate charge matched to the capabilities of th e battery (typi cally a one or two hour ra t e, depending on battery t ype and charger power module rati ng).
6 1 - - - - - - - 2 - - - - - - - LCD Indications Each PowerCharger’s liquid crystal displa y (LCD) will display the status of each battery, as well as, important PowerCharg er operating indications. The fol lowing information expl ains the indications whic h appear in the LCD.
7 LED Indications Each charge position of a PowerCharger has a pair of LEDs (one red, one green) which indicate the status of th e battery attached to that p osition.
8 Priority Battery Function A unique operating feature of all PowerCharg ers allows the operator to select any battery on any charge position as a PRIORI TY BATTERY.
9 The standard test is adequ ate for virtually all conditio ns to verify the capacity o f the battery before taking it into the fiel d. The 24 hour test need only be perform ed on a battery, typical ly an older one (2 years or m ore), which may have exhibited questionable performance.
10 When testing is completed, the LCD Main Display will indicate “TEST DONE”. To display or prin t test results: 1. Press the DISPLAY button on the PowerCharger front panel to scrol l to the Primary Position Display for the battery tested. 2. Press the TEST button.
11 OPERATION AS DC CAMERA SUPPLY FROM MAINS Each PowerCharger model can operate cam eras and cam corders using the four pin camera output connector located at the back of the PowerCharger. To power the camera, attach one end of the XLR4 accessory cable (a vailable separately) to the PowerCharger.
12 POWER LOSS MEMORY MODE The PowerCharger features a special Powe r Loss Mem ory or “Power Down” mode. When mains power is interrupted while ba tteries are mounted, the PowerCharger will automatically indicate the charge status o f all batteries until po wer is restored (up to 16 hours).
13 WARRANTY IMPORTANT: PLEASE MAIL WARRANTY REGISTRATION CARD WITHIN TEN (10) DAYS OF PURCHASE. We must have this card on file at our SERVICE DEPARTMENT to establish this warranty. Pr oper registration will also enable us to provide update inform ation on the InterActi ve 2000 PowerCharger battery syst em.
An important point after buying a device Anton/Bauer QUAD 2702 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Anton/Bauer QUAD 2702 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Anton/Bauer QUAD 2702 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Anton/Bauer QUAD 2702 you will learn all the available features of the product, as well as information on its operation. The information that you get Anton/Bauer QUAD 2702 will certainly help you make a decision on the purchase.
If you already are a holder of Anton/Bauer QUAD 2702, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Anton/Bauer QUAD 2702.
However, one of the most important roles played by the user manual is to help in solving problems with Anton/Bauer QUAD 2702. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Anton/Bauer QUAD 2702 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
