Instruction/ maintenance manual of the product NM 19 Anton/Bauer
Go to page of 10
O n e W o r l d . O n e S m a r t C h o i c e . ™ O wner ’ s Manual NM14/19 & 28/38 A7595-0366 Rev C ® Approved Copy.
T ABLE OF CONTENTS 1 INTRODUCTION 1-2 NM 14/19 BA TTER Y MODULE DISASSEMBL Y 3 NM 14/1919 BA TTER Y MODULE ASSEMBL Y 4-5 NM 28/38 BA TTER Y DISASSEMBL Y 5-6 NM 28/38 BA TTER Y ASSEMBL Y 7 LIMITED W AR.
1 INTRODUCTION The CINE VCLX series of batteries are designed and manufactur ed to the high quality expected from all Anton/Bauer batteries. Because of the specialized and proprietary cir cuitry that is used in these batteries, the cells inside of any CINE battery must be replaced with an NM14/19 or NM28/38 module.
2 NM 14/19 BA TTER Y MODULE DISASSEMBL Y OF UNIT (CONTINUED) STEP 3 Remove the rubber side plate assembly from the unit as shown in gure C. STEP 4 Remove the (1) 6-32 x 5/16 screw fr om the sheet metal case. Slide the battery cell assembly from the electr onics assembly as shown in gure D.
3 NM14/19 RE-ASSEMBL Y OF UNIT STEP 1 Plug the 2 connectors exiting from the battery cell assembly to the mat - ing connectors of the electronics assembly as shown in gure F . Figure F STEP 2 Coil the excess harness and wrap with the rubber band. Slide the battery cell assembly into the electronics assembly .
NM 28/38 BA TTER Y DISASSEMBL Y OF UNIT STEP 1 Remove the (4) #10 screws and (4) # 10 washers as shown in gure A. NOTE: Do not remove handle or handle har dware from side plates.
STEP 5: Remove the rubber band from the coiled harness and disconnect the 2 connectors as shown in gure E. NM 28/38 BA TTER Y DISASSEMBL Y OF UNIT (CONTINUED) Figure E NM 28/38 BA TTER Y RE-ASSEMBL.
NM 28/38 BA TTER Y RE-ASSEMBL Y OF UNIT (CONTINUED STEP 3 Install the (4) 6-32 x 3/8 washers and screws as shown in gur e H. Figure H STEP 4 Install (4) #10 washers and screws as shown in gur e I.
BA TTER Y LIMITED W ARRANTY 0-12 MONTHS - “Anton/Bauer will repair or replace the pr oduct at Anton/ Bauer’ s option - FREE OF CHARGE. ” This limited warranty for the product specied in this document is given by Anton/Bauer , Inc. (“Anton/Bauer”), 14 Progr ess Drive, Shelton, Con - necticut 06484.
5 Anton/Bauer A Vitec Gr oup brand The following ar e trademarks of Anton/Bauer , Inc.: Anton/Bauer , Anton/Bauer logo and parallelogram design, Aspekt, A utomatique, Data T ap, DIONIC, Elipz, Egripz,.
An important point after buying a device Anton/Bauer NM 19 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Anton/Bauer NM 19 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Anton/Bauer NM 19 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Anton/Bauer NM 19 you will learn all the available features of the product, as well as information on its operation. The information that you get Anton/Bauer NM 19 will certainly help you make a decision on the purchase.
If you already are a holder of Anton/Bauer NM 19, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Anton/Bauer NM 19.
However, one of the most important roles played by the user manual is to help in solving problems with Anton/Bauer NM 19. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Anton/Bauer NM 19 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
