Instruction/ maintenance manual of the product P180B Fan Antec
Go to page of 9
P180B User’s Manual Manuel de l’utilisateur Anwenderhandbuch Manuale per l’operatore Manual del usuario পᡅ䂀ᯢ.
1 At Antec, we continually refine and improve our products to ensure the highest quality. So it’s possible that your new case may differ slightly from the descrip- tions in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct.
2 6. Place your motherboard on the brass standoffs. 7. Screw in your motherboard to the standoffs with the provided Philips-head screws. Your motherboard is now installed. Front Bezel Connectors 1. Connect the Reset switch (labeled RESET SW) to your motherboard at the RST connector.
3 Note: Please check your motherboard manual for your IEEE 1394 header pin layout and make sure it matches the attached table. If you intend to connect the front FireWire port to an IEEE 1394 add-on c.
4 3. There are two HDD trays inside the cage. Squeeze the metal clips on each side of a tray and slide it out. 4. Mount your hard drive to the drive tray with the special screws provided. Don’t over-tighten the screws since that could decrease the grommets’ ability to absorb vibration and noise.
5 5. Please refer to the power supply installation section, to route the power cables to your devices. Once you’ve done so, connect the appropriate power connec- tors to your device.
6 These two fans are mounted so that the air is blowing out of the case. The top fan comes with a spoiler to mount on the top of the case. To install the spoiler: 1. With the spoiler open end facing the rear of the case, carefully align the tabs of the spoiler with the notches on the case.
7 The Optional Fans There are two optional 120mm fan mounts — the front fan (located in front of the upper HDD cage) and the middle fan (located inside the upper HDD cage). These two fans should be installed so that the air is blowing into the case from the front.
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam The Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Technical Support: US & Canada 1-800-22ANTEC customersupport@antec.
An important point after buying a device Antec P180B Fan (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Antec P180B Fan yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Antec P180B Fan - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Antec P180B Fan you will learn all the available features of the product, as well as information on its operation. The information that you get Antec P180B Fan will certainly help you make a decision on the purchase.
If you already are a holder of Antec P180B Fan, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Antec P180B Fan.
However, one of the most important roles played by the user manual is to help in solving problems with Antec P180B Fan. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Antec P180B Fan along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
