Instruction/ maintenance manual of the product KRC-435 Kenwood
Go to page of 31
KRC-435 © B64-2235-00 (KW) Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new cassette-receiver.
— 2 — English Contents Safety precautions ......................3 About Cassette tape ...................4 General features .......................
— 3 — T o prevent injury or fire, take the following precautions: • Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted. • When extending the ignition, battery , or ground wires, make sure to use automotive- grade wires or other wires with a 0.
— 4 — English • If you experience problems during installation, consult your Kenwood dealer . • If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer .
Press the [SRC] button. Source required Display T uner "TUNER" T ape "T APE" External disc "DISC-CH" Auxiliary input "AUX" Standby (Illumination only mode) "ALL OFF" For Auxiliary input one of the below optional accessories is necessary .
1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted switch as shown below .
For 5 & 4 in. speaker "SP 5/4" For 6 & 6x9 in. speaker "SP 6*9/6" For the OEM speaker "SP OEM" 4 Exit Speaker Setting mode Press the [Q] button. Fine-tuning so that the System Q value is optimal when setting the speaker type.
Attaching a title to a Station or CD. 1 Receive/play the station/disc you want to attach a title to • A title can't be attached to a MD. • Disc Naming can't be done during CD text or clock display . 2 Enter name set mode Press the [NAME] button for at least 2 seconds.
Selecting the display when this device is switched to Auxiliary input source. 1 Select Auxiliary input source Press the [SRC] button. Select the "AUX" display . 2 Enter Auxiliary input display setting mode Press the [DISP] button for at least 2 seconds.
T uner features The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing the Faceplate 1 Press the Release button. Drop open the faceplate. 2 Drawing the faceplate to left side pull it to the front and remove it. • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts.
Putting the station in the memory . 1 Select the band Press the [FM] or [AM] button. 2 Select the frequency to put in the memory Press the [ 4 ] or [ ¢ ] button. 3 Put the frequency in the memory Press the [#1] — [#6] button for at least 2 seconds.
Cassette player features Calling up the stations in the memory . 1 Select the band Press the [FM] or [AM] button. 2 Call up the station Press the [#1] — [#6] button. Preset T uning Putting stations with good reception in the memory automatically . 1 Select the band for Auto Memory Entry Press the [FM] or [AM] button.
When there's no Cassette T ape inserted 1 Drop open the faceplate Press the Release button. 2 Insert a Cassette T ape. 3 Press the faceplate on the right side, and return it to its former position. • When the faceplate has been dropped open, it might interfere with the shift lever or something else.
External disc control features Repeating the present song. Press the [REP] button. Each time the button is pressed the Music Repeat turns ON or OFF . When it's ON, "REP ON" is displayed. Music Repeat Fast forwarding automatically when an unrecorded portion continues for at least 10 seconds.
Doing T rack Search by entering the track number . 1 Enter the track number Press the number buttons on the remote. 2 Do T rack Search Press the [ 4 ] or [ ¢ ] button. Canceling Direct T rack Search Press the [ 38 ] button. Direct T rack Search (Function of remote) Selecting the disc you want to hear .
Play the songs on all the discs in the disc changer in random order . Press the [M.RDM] button. Each time the button is pressed the Magazine Random Play turns ON or OFF . When it's ON, "MRDM ON" is displayed. Magazine Random Play (Function of disc changer) Playing all the songs on the disc in random order .
Menu system Selecting the CD displayed in the DNPS of the CDs set in the Disc changer . 1 Enter DNPP mode Press the [DNPP] button on the remote. When "DNPP " is displayed the DNPS display in order . Forward / Reverse display Press the [DISC–] or [DISC+] button.
removed from the vehicle, personalizing this unit is by using the Security Code is a help in preventing theft. When the Security Code function is activated, the code can't be changed and the function can't be released. Note, the Security Code can be set as the 4 digit number of your choice.
Setting the graphic part display ON/OFF . Display Setting "GRPH ON" The graphic part is displayed. "GRPH OFF" The graphic part isn't displayed. Switching Graphic Display A red indicator will blink on the unit after the faceplate is removed, warning potential thieves.
Basic Operations of remote Setting the displayed text scroll. Display Setting "SCL AUTO" Repeats scroll. "SCL MANU" Scrolls when the display changes.
[FM]/ [AM] buttons Select the band. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands. [ 4 ]/ [ ¢ ] buttons T une up or down band. [#0] — [#9] buttons Press buttons [#1] — [#6] to recall preset stations. [DIRECT] button Enters and cancels the <Direct Access T uning> (page 11) mode.
[ 4 ]/ [ ¢ ] buttons Doing track forward and backward. [DISC+]/ [DISC–] buttons Doing album forward and backward. [ 38 ] button Each time the button is pressed the song pauses and plays. [DNPP]/ [OK] button Enters and cancels the <DNPP (Disc Name Preset Play)> (page 17) mode.
— 23 — — 23 — The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 1. T o prevent a short circuit, remove the key from the ignition and disconnect the - battery .
English — 24 — — 24 — P.CONT ANT. CONT. FRONT • L FRONT • R REAR • L REAR • R – + FM/AM antenna input 1 Front left output (White) 23 Front right output (Red) 28 Fuse (10A) 24 Wiring .
— 25 — Accessory 5 If you want to fasten the faceplate to the main unit so that it does not fall off, screw in the provided screws (ø4 X 16 mm) in the holes shown below . Bottom panel — 25 — Make sure that the unit is installed securely in place.
English — 26 — — 26 — ■ Removing the hard rubber frame 2 When the lower level is removed, remove the upper two locations. The frame can be removed from the top side in the same manner . Catch Lock 1 Engage the catch pins on the removal tool and remove the two locks on the lower level.
— 27 — What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. 01 ✔ The fuse has blown.
English — 28 — Disc source ? "AUX" is displayed without achieving External disc control mode. 50 ✔ O-N switch is set to "O" side. ☞ Set the switch to "N" side. ✔ Unsupported disc changer is connected. 51 ☞ Connect the supported disc changer .
— 29 — direction for the first song or in the forward direction for the last song. If the following situations, consult your nearest service center: • Even though the disc changer is connected, the Disc Changer source is not ON, with "AUX" showing in the display during the Changer Mode.
English — 30 — T roubleshooting Guide The messages shown below display your systems condition. EJECT : No disc magazine has been loaded in the changer . The disc magazine is not completely loaded. E01 ➪ Load the disc magazine properly . No CD in the unit.
— 31 — Specifications FM tuner section Frequency range (200 kHz space) .............87.9 MHz –107.9 MHz Usable sensitivity (S/N = 30dB) ................... 9.3 dBf (0.8 µV/75 Ω ) Quieting Sensitivity (S/N = 50dB) .............. 15.2 dBf (1.6 µV/75 Ω ) Frequency response ( ± 3 dB) .
An important point after buying a device Kenwood KRC-435 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kenwood KRC-435 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kenwood KRC-435 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kenwood KRC-435 you will learn all the available features of the product, as well as information on its operation. The information that you get Kenwood KRC-435 will certainly help you make a decision on the purchase.
If you already are a holder of Kenwood KRC-435, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kenwood KRC-435.
However, one of the most important roles played by the user manual is to help in solving problems with Kenwood KRC-435. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kenwood KRC-435 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
