EN
Kenmore logo
Official user manual

Kenmore 790.324

16 pages·3.3 MB·Cooktop·PDF·ENDEFRITNLJA
Kenmore 790.324
Table of Contents 33 sections GAS COOKTOP · E COCl A A GAS · FOR YOUR SAFETY: · important Safety instructions · … ShowHide
Page 1 of the Kenmore 790.324 user manual — GAS COOKTOP
Page 1 · click to enlarge
Page 1
Kenmore 790.324 — GAS COOKTOP diagram (page 1)
Fig. 1

GAS COOKTOP

E COCl A A GAS

Models, Modelos 790. 3240-,-, 3241 -,- -,- = color number, n_mero de color

Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com

P/N 318203661 Rev. A (0903)

®

Page 2 of the Kenmore 790.324 user manual — GAS COOKTOP
Page 2 · click to enlarge
Page 2
Page 2 of the Kenmore 790.324 user manual — GAS COOKTOP
Page 3 of the Kenmore 790.324 user manual — FOR YOUR SAFETY:
Page 3 · click to enlarge
Page 3
Kenmore 790.324 — FOR YOUR SAFETY: diagram (page 3)
Fig. 2

This manual contains important safety symbols and instructions. Please pay attention to these symbols and follow all instructions given.

_ This symb01 Will help alert you to situations that may cause sedous b0d!ly haim; death or property damage:

This symbol will help alert y0u to situations that may Cause b0dily injury or

if the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

FOR YOUR SAFETY:

-- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WHATTO DO IFYOU SMELL GAS: * Do not try to light any appliance. * Do not touch any electrical switch; do not use any phone in your building. * Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions. if you cannot reach your gas supplier, call the fire department. o

Installation and service must be performed by a qualified installer, servicer or the gas supplier.

,, Remove all tape and packaging wrap before using the cooktop. Destroy the carton and plastic bags after unpacking the cooktop. Never allow children to play with packaging material. Do not remove the model/ serial plate attached to the cooktop.

This includes paper, plastic and cloth items, such as cookbooks, plasticware and towels, as well as flam- mable liquids. Do not store explosives, such as aero- sol cans, on the cooktop. Flammable materials may explode and result in fire or property damage.

* Proper Installation--Be sure your appliance is prop= erly installed and grounded by a qualified technician in accordance with the National Fuel Gas Code ANSI Z223.1 latest edition and CAN/CGA B149.2, and the National Electrical Code ANSI/NFPA No. 70--latest edition, and local code requirements. Install and/or adjust only per installation instructions provided in the literature package for this cooktop.

Do not store items of interest to chil- dren in the cabinets above the cooktop.

,, Do not leave children alone--Children should not

be left alone or unattended in the area where an ap= pliance is in use. They should never be allowed to sit or stand on any part of the appliance.

,, DO NOTTOUCH SURFACE BURNERS, GRATES, OR AREAS NEAR THESE BURNERS. Surface burners

,, in case of an emergency, know how to disconnect the electrical power to the appliance at the circuit breaker or fuse box.

may be hot even though the flames are not visible. Areas near surface burners may become hot enough to cause burns. During and after use, do not touch or

,, User Servicing. Do not repair or replace any part of the appliance unless specifically recommended in the product literature supplied with this appliance. All other servicing should be done only by a qualified technician to reduce the risk of personal injury and dam- age to the appliance. Sears Parts & Repair is the recom- mended repair service for this appliance.

let clothing or other flammable materials touch these areas until they have had sufficient time to cool. Among these areas are the cooktop and the surfaces facing the cooktop.

,, Wear Proper Apparel--Loose-fitting or hanging garments should never be worn while using the ap= pliance. Do not let clothing or other flammable materi- als contact hot surfaces.

,, Never modify or alter the construction of a cooktop by removing panels, wire covers, or any other part of the product.

NEVER use this appliance as a space heater to heat or warm the room. Doing so may result in carbon monoxide poisoning.,, Do Not Use Water or Flour or= Grease Fires--

Stepping or leaning on this cooktop can result in serious injuries and may also cause dam- age to the cooktop. Do not allow children to climb or play around the cooktop. ,, Storage on Appliance--Flammable materials should not be stored on the cooktop, near surface burners.

Smother the fire with a pan lid, or use baking soda, a dry chemical or foam=type extinguisher.

* When heating fat or grease, watch it closely. Fat or grease may catch fire if allowed to become too hot.

Page 4 of the Kenmore 790.324 user manual — IMPORTANT SAFETY NOTICE
Page 4 · click to enlarge
Page 4
Kenmore 790.324 — important Safety instructions diagram (page 4)
Fig. 3 · important Safety instructions

important Safety instructions

= Use Only Dry Potholders--IVIoist or damp pot hold- ers on hot surfaces may result in burns from steam. Do not let the potholders touch the flame or burners. Do not use a towel or other bulky cloth instead of a pot holder.

  • Utensil Handles Should Be Turned Inward from Edges of Cooktop and Not Extend Over Adjacent Surface Burners--To reduce the risk of burns, ignition of flammable materials, and spillage due to unintentional contact with the utensil, the handle of the utensil should be positioned so that it is turned inward, and does not extend over adjacent surface burners.
  • Never Leave Surface Burners Unattended at High Heat Settings--Boilovers cause smoking and greasy spillovers that may ignite, or a pan that has boiled dry may melt.

= Do Not Heat Unopened Food Containers--Buildup of pressure may cause container to burst and result in injury.

= Know which knob controls each surface burner.

Always turn the knob to the LITE position when igniting the burners. Visually check that the burner has lit. Then adjust the flame so it does not extend beyond the edge of the utensil.

  • Protective Liners--Do not use aluminum foil to line sur-

face burner pans. Protective liners or aluminum foil may interfere with heat and air distribution, and combustion. Damage to the cooktop or personal injury may result.

Use Proper Flame Size--Adjust flame size so it does not extend beyond the edge of the uten- sil. The use of undersized utensils will expose a portion of the burner flame to direct contact and may result in ignition of clothing. Proper relationship of utensil to flame will also improve efficiency.

  • Glazed Cooking Utensils--Only certain types of glass, glass/ceramic, ceramic, earthenware, or other glazed utensils are suitable for cooktop service without breaking due to the sudden change in temperature. Check the manufacturer's recommendations for cooktop use.

Do not use stove top grills on your sealed gas burners. If you use a stove top grill on a sealed gas burner, it will cause incomplete combustion and can result in exposure to carbon monoxide levels above allowable current standards. This can be hazardous to your health.

  • Do Not Use Decorative Surface Burner Covers. if a burner is accidentally turned on, the decorative cover will become hot and possibly melt. You will not be able to see that the burner is on. Burns will occur if the hot covers are touched. Damage may also be done to the cooktop or burners because the covers may cause overheating. Air will be blocked from the burner and cause combustion problems.

Use proper pan size--This appliance is equipped with one or more surface burners of different sizes. Select utensils having flat bottom large enough to cover the surface burner. The use of undersized utensils will expose a portion of the surface burner to direct contact and may result in ignition of clothing. Proper relationship of utensil to the surface burner will also improve efficiency.

IMPORTANT SAFETY NOTICE

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of potential exposure to such substances.

  • Clean the appliance regularly to keep all parts free of grease that could catch fire. Exhaust fan ventilation hoods and grease filters should be kept clean. Do not allow grease to accumulate on hood or filter. Greasy deposits in the fan could catch fire. When flaming food under the hood, turn fan on. Refer to hood manufacturer's instructions for cleaning.
Page 5 of the Kenmore 790.324 user manual — (Propane) Gas Conversion
Page 5 · click to enlarge
Page 5
Kenmore 790.324 — Grounding instructions diagram (page 5)
Fig. 4 · Grounding instructions

Grounding instructions

This appliance is equipped with a 3-prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded receptacle. DO NOT cut or remove the grounding prong from this plug. If a 2-prong wall receptacle is the only available outlet, it is the personal responsibility of the consumer to have it replaced with a properly grounded 3-prong wall receptacle installed by a qualified electrician.

receptacle Do not, under any circumstances, cut, remove, or bypass the grounding

prong.

Avoid fire hazard or electrical shock. DO NOT use an adapter plug, an extension cord, or remove grounding prong from electrical power cord. Failure to follow this warning can cause serious injury, fire or death.

Power supply cord with 3-prong grounding plug

See the INSTALLATION INSTRUCTIONS packaged with this cooktop for complete installation and grounding instructions.

(Propane) Gas Conversion

Liquefied Petroleum

This appliance can be used with Natural Gas and Propane Gas. It is shipped from the factory for use with natural gas.

Severe electrical shock, or damage to the cooktop, may occur if the cooktop is not converted by a qualified installer or electrician.

If you wish to convert your cooktop for use with propane gas:

For models with Open Burners, convert according to directions in the Gas Cooktop Installation Instructions.

To avoid serious injury, any additions, changes or conversions required in order for this appliance to satisfactorily meet the application needs must be made by a qualified service agent.

For models with Sealed Burners, convert according to the instructions in the attached envelope marked FOR LP/PROPAN E GAS CONVERSION.

Only a qualified service agent should perform the L. R conversion. Contact the local gas provider for conversion. An L. R Conversion Kit is supplied with this range and is located on the main back of the range. The kit contains installation instructions which must be read before and followed carefully when installing the kit.

Grounding type wall

Page 6 of the Kenmore 790.324 user manual — Specialty Pans & Trivets
Page 6 · click to enlarge
Page 6
Kenmore 790.324 — Surface Cooking diagram (page 6)
Fig. 5 · Surface Cooking

Surface Cooking

CORRECT

iNCORRECT • Curved and warped pan bottoms.

Use Proper Cookware

Cookware should have flat bottoms that make

  • Pan overhangs unit by more than 2.5 cm (1").

,, Fiat bottom and straight sides.

good contact with the entire surface heating element. Check for

  • Tight fitting lids.
  • Weight of handle does not tilt

pan. Pan is well balanced. • Pan sizes match the amount of

flatness by rotating a ruler across the bottom of the cookware Figure 1

  • Heavy handle tilts pan.

food to be prepared. • Made of material that conducts

(See Figure 1). Be sure to follow the recommendations for using cookware as shown in Figure 2.

heat well.

  • Flame extends beyond unit.
  • Easy to clean.

* Specialty pans such as lobster pots, griddles and pressure cookers may be used but must conform to the above recommended cookware require- ments.

the oven or on the cooktop.

Specialty Pans & Trivets

Woks with flat bottoms suitable for use on your cooktop are available in most cookshop or hardware stores. Round-bottomed woks (with a support ring that does not extend beyond the burner flames) may also be used. The metal ring was designed to support the wok safely when it is filled with large amounts of liquids (soup making) or fat (frying).

DO NOT use a wok if it is equipped with a metal ring that extends beyond the burner flames. Because this ring traps heat, the surface unit and cooktop surface could be damaged.

Wire trivets: Do not use wire trivets. Cookware bottoms must be in direct contact with the grates.

DO NOT use two burner units to heat one large pan such as a roaster or griddle, or al- low cooking utensils to boil dry. The bottom surface of the pan in either of these situations could cause dis- coloring or crazing of the appliance cooking surface, and damage to the grates and burner units.

Page 7 of the Kenmore 790.324 user manual — Flame Size
Page 7 · click to enlarge
Page 7
Kenmore 790.324 — Canning Tips & Information diagram (page 7)
Fig. 6 · Canning Tips & Information

Surface Cooking

Canning Tips & Information

Canning can generate large amounts of steam. Use extreme caution to prevent burns. Always raise the lid to vent steam away from you. 1. Use tested recipes and follow instructions carefully. Check with your local Cooperative Agricultural Extension Service or a manufacturer of glass jars for the latest canning information. 2. Use flat-bottomed canners only. Heat is spread more evenly when the bottom surface is flat.

3. Center the canner on the burner grate. 4. Start with hot water and a high heat setting to reduce the time it takes to bring the water to a boil; then reduce the heat setting as low as possible to maintain a constant boil.

Safe canning requires that harmful micro-organisms are destroyed and the jars are sealed completely. When canning in a water bath canner, a gentle but steady boil must be maintained continuously for the required time. When canning with a pressure canner, the pressure must be maintained continuously for the required time.

5. It is best to can small amounts and light loads.

Prevent damage to cooktop and burner grates: 1. Do not use water bath or pressure canners that extend more than one inch (2.5 cm) beyond the edge of the burner grate. 2. Do not leave water bath or pressure canners on high heat for an extended amount of time. 3. Alternate surface units between each batch to allow the units and surrounding surfaces to cool down. Try to avoid canning on the same burner unit all day.

Flame Size

For most cooking, start on the highest control setting and then turn to a lower one to complete the process. Use the table below as a guide for determining proper flame size for various types of cooking. The size and type of utensil used and the amount of food being cooked will influence the setting needed for cooking.

For deep fat frying, use a thermometer and adjust the surface control knob accordingly. If the fat is too cool, the food will absorb the fat and be greasy. If the fat is too hot, the food will brown so quickly that the center will be undercooked. Do not attempt to deep fat fry too much food at once as the food will neither brown nor cook properly.

*Flame Size Type of Cooking

High Flame Start most foods; bring water to a boil; pan broiling

Medium Flame Maintain a slow boil; thicken sauces, gravies; steam Low Flame Keep foods cooking; poach; stew

*These settings are based on using medium-weight aluminum pans with lids. Settings may vary when using other types of pans.

Never extend the flame beyond the outer edge of the utensil. A higher flame simply wastes heat and energy, and increases your risk of being burned by the flame.

Proper Burner Adjustments The color of the flame is the key to proper burner adjustment. A good flame is clear, blue and hardly visible in a well-lighted room. Each cone of flame should be steady and sharply defined. Adjust or clean burner if flame is yellow-orange. To clean burner, see instructions under General Cleaning.

,2"

Page 8 of the Kenmore 790.324 user manual — Setting Surface Controls
Page 8 · click to enlarge
Page 8
Kenmore 790.324 — Placement of Burner Bases and Caps (Models with sealed burner only) diagram (page 8)
Fig. 7 · Placement of Burner Bases and Caps (Models with seal…

Surface Cooking

Placement of Burner Bases and Caps (Models with sealed burner only)

Your cooktop is equipped with three different sized burners: Power Burner (large), Standard Burner (medium) and Simmer Burner (small).

Place the burner base over each gas opening, matching the burner base size with the gas opening size. Place the burner cap on each burner base, again matching the cap size to the burner base size. The cap for the each Burner has an inner locating ring which locates the burner cap in the center of the burner.

Make sure each burner cap is properly aligned and level.

Turn the burner on to determine if it will light. If the burner does not light, contact a Sears Service Center. Do not service the sealed burner yourself.

Setting Surface Controls

The surface control knobs shown

Open Burner Models To Adjust Low or "Simmer" Setting (some models) The burner flame, at low setting, can be adjusted if it is too high or too low; refer to the Installation Instructions for adjustment procedure.

below may not look identical to the Surface Controls Knobs on your range; They are only representational.

To operate the Surface Burner: 1. Place cooking utensil on burner. 2. Push in and turn the Surface Control knob to LITE. Note: All electronic

ignitors will click at the same time. However, only the burner you are turning on will ignite. 3. Visually check that the burner has lit. 4. After the burner lights, turn the control knob to the desired flame size. The control knobs do not have to be set at a particular mark. Use the guides and adjust the flame as needed. DO NOT cook with the control knob in the

LITE position. (The electronic ignitor will continue to click if left in the LITE position.)

Sealed Burner

Page 9 of the Kenmore 790.324 user manual — Setting Surface Controls Sealed Burner Models
Page 9 · click to enlarge
Page 9
Kenmore 790.324 — Setting Surface Controls Sealed Burner Models diagram (page 9)
Fig. 8 · Setting Surface Controls Sealed Burner Models

Setting Surface Controls Sealed Burner Models

Your appliance may be equipped with any combination of the following burners:

The surface control knobs shown below may not look identical to the Surface Controls Knobs on your range; They are only representational.

Simmer Burner: This burner is best used for simmering delicate sauces, etc. Standard Burner: This burner can be used for most all surface cooking needs. Power Burner: This larger burner is best used when bringing large quantities of liquid to temperature and when preparing larger quantities of food.

Regardless of size, always select a utensil that is suitable for the amount and type of food being prepared. Select a burner and flame size appropriate to the pan. Never allow flames to extend beyond the outer edge of the pan. Each burner lights from an electric ignitor when its control knob is turned to the lite position.

To operate the surface burner: 1. Place cooking utensil on burner. 2. Push in and turn the Surface Control knob to LITE. Note: All electronic

ignitors will click at the same time. However, only the burner you are turning on will ignite. 3. Visually check that the burner has lit. 4. After the burner lights, turn the control knob to the desired flame size. The control knobs do not have to be set at a particular mark. Use the guides and adjust the flame as needed. DO NOT cook with the control knob in the LITE position. (The electronic ignitor will continue to click if left in the LITE position.) 5. To turn the burner off, turn the control knob as far as it will go, to the OFF position.

Manual Ignition In the event of an electrical power outage, the surface burners can be lit manually. To light a surface burner, hold a lit match to the burner head, then slowly turn the surface control knob to LITE. Use caution when lighting surface burners manually.

Surface burner in use when an electrical power failure occurs will continue to operate normally.

Do not operate the burner for an extended period of time without cookware on the grate, The finish on the grate may chip without cookware to absorb the heat.

Do not place plastic items such as salt and pepper shakers, spoon holders or plastic wrappings on top of the cooktop when it is in use. These items could melt or ignite. Pot holders, towels or wood spoons could catch fire if placed too close to a flame.

Page 10 of the Kenmore 790.324 user manual — Setting Surface Controls Sealed Burner Models
Page 10 · click to enlarge
Page 10
Kenmore 790.324 — Setting Surface Controls Sealed Burner Models diagram (page 10)
Fig. 9 · Setting Surface Controls Sealed Burner Models

Cleaning Various Parts of Your Cooktop Before cleaning any part of the cooktop, be sure all controls are turned OFF and the cooktop is COOL. REMOVE SPILL OVERS AND HEAVY SOILING AS SOON AS POSSIBLE. REGULAR CLEANING NOW WILL REDUCE THE DIFFICULTY AND EXTENT OF A MAJOR CLEANING LATER.

Surfaces How to Clean

Aluminum (Trim Pieces) & Vinyl Use hot, soapy water and a cloth or paper towel. Dry with a clean cloth.

Painted and Plastic Control Knobs, Body Pieces, and Decorative Trim

For general cleaning, use hot soapy water and a cloth. For more difficult soils and built-up grease, apply a liquid detergent directly onto the soil. Leave on soil for 30 to 60 minutes. Rinse with a damp cloth and dry. DO NOT use abrasive cleaners on any of these materials; they can scratch or dull the finish.

Wipe the control panel clean after each use. Before cleaning the control panel turn all controls to OFF and remove the control knobs. To remove, pull each

knob straight off the shaft. Clean using hot, soapy water and a cloth. Be sure to squeeze excess water from the cloth before wiping the panel; especially when wiping around the controls. Excess water in or around the controls may cause damage to the appliance. To replace knobs after cleaning, line up the flat sides of both the knob and the shaft; then push the knob into place.

Stainless Steel, Chrome, Decorative Trim

Clean with hot, soapy water and a dishcloth. Rinse with clean water and cloth. Do not use cleaners with high concentrations of chlorides or chlorines. Do not use harsh scrubbing cleaners. Only use kitchen cleaners that are especially made for cleaning stainless steel. Always be sure to rinse the cleaners off from the surface as bluish stains may occur during heating that cannot be removed.

Gentle scouring with a soapy scouring pad will remove most spots. Rinse with a 1:1 solution of clear water and ammonia. If necessary, cover difficult spots with an ammonia-soaked paper towel for 30 to 40 minutes. Rinse with clean water and a damp cloth, and then scrub with a soap-filled scouring pad. Rinse and wipe dry with a clean cloth or paper towel. Remove all cleaners or the porcelain

Burner Grates, Burner Pans (some models), Burner Rings (some models), Cooktop Surface

may become damaged during future heating. DO NOT use spray oven cleaners on the cooktop.

The holes in the burners of your cooktop must be kept clean at all times for proper ignition and a complete, even flame. Clean the burner holes routinely with a small gauge wire or needle and especially after bad spillovers which could clog these holes.

To remove and replace burner units per your model, see instructions under General Cleaning. To clean, soak the burners in a 1:1 solution of ammonia and water for 30 to 40 minutes. For stubborn stains, scrub with soap and water or a

mild abrasive cleanser and damp cloth. Dry the burners thoroughly in a warm oven for 30 minutes. Then replace them, making sure they are seated and level.

DO NOT wash burner units in the dishwasher.

Control Panel · Porcelain Enamel · Surface Burners

Page 11 of the Kenmore 790.324 user manual — SURFACES CLEANING AGENTS INSTRUCTIONS
Page 11 · click to enlarge
Page 11
Kenmore 790.324 — Porcelain enamel cooktop cleaning instructions diagram (page 11)
Fig. 10 · Porcelain enamel cooktop cleaning instructions

Porcelain enamel cooktop cleaning instructions

Correct and consistent cleaning is essential to maintaining your porcelain enamel cooktop. If food spills and grease spatters are not removed, they may burn onto the surface of the cooktop and cause permanent discoloration.

Do not use a

cooktop cleaner on a hot cook- top. The fumes can be hazardous to your health, and can chemical-

Daily Cleaning For normal soil: 1. Allow cooktop surface to cool. 2. Wipe off spills and spatters using a clean paper towel or a clean cloth with warm, soapy water. 3. If needed, use mild household cleaners or a soap-filled steel wool pad. 4. Be sure to rinse off all cleaning solutions or the porcelain may become damaged during future heating.

ly damage the cooking surface.

Before cleaning the surface cooktop, be sure the controls are turned to OFF and the cooktop is cool.

For heavy, burned=on soil: 1. Allow cooktop surface to cool. 2. Use a soap filled scouring pad with warm water or cover heavily soiled spots with a solution of clear water and ammonia. Scour gently. Rinse and wipe dry with a clean cloth.

commercial oven cleaners on the exterior surfaces including rangetop and door frame.

SURFACES CLEANING AGENTS INSTRUCTIONS

Porcelain enamel Mild cleaners or soap-filled Use a damp sponge or (cooktop, surface steel wool pads. dampened soap pad, rinse and under cooktop) dry.

Control Knob Area Hot, soapy water or cleaner Use a clean soapy, dampened cream, cloth or paper towel, remove soil and dry. Do not use abrasive products.

DO NOT use

Page 12 of the Kenmore 790.324 user manual — Lig
Page 12 · click to enlarge
Page 12
Kenmore 790.324 — Lig diagram (page 12)
Fig. 11 · Lig

Open Burner Models (somemodels) To Raise and Lower the Top for Cleaning The cooktop is hinged and can be raised to clean the area underneath. Be sure all cooktop controls are turned to OFF and burner grates are cool. 1. Remove control knobs, burner grates and spillover bowls. Set aside. 2. Grasp the front of the cooktop and lift. Some models have a swing-up rod to support the cooktop in its raised position. 3. Clean under the cooktop. 4. Lower the top gently after lowering the support rod (some models). 5. Replace bowls, grates and control knobs.

When lowering the top, grasp the sides with fingertips only. Be careful not to pinch fingers. Also, DO NOT drop or bend the cooktop when raising or lowering. This could damage the surface.

DO NOT turn on the burners when the cooktop is raised for cleaning. Be sure that the top is completely lowered and securely in place before turning on the burners.

To Remove and Replace Burners The burners on your cooktop maybe removed for cleaning. Be sure all controls are turned to OFF and burner grates are cool before removing cooktop burner units.

To Remove Burner Assemblies

1. Remove the shipping screw from the support brackets. See illustrations for location of screws.
2. Grasp the burner head and tilt it slightly (A in Figure 1) to the right to release the tab from the burner support. 3. Lift up the support bracket (see Figure 2) slightly and pull it away from the front of the cooktop to free the air shutter from the gas valve orifice (B in Figure 1).

Check the lighter and burner ports (Figure 2). If they are clogged, use a wire or needle to clear them.

To remove burned-on food, soak the burners in a vinegar and water solution for 20-30 minutes. For stubborn stains, scrub with soap and water or a mild abrasive cleanser and a damp cloth. Do not wash burners in a dishwasher.

To Replace Burner Assemblies 1. Slide the air shutter over the gas valve orifice (Figure 1). 2. Lower the burner assembly and hook the tab in the slot in the burner support. Make sure the burner assembly is properly seated and level. 3. Be sure both tabs are in the correct slots, the burner sits level and straight, and the flash tube forms a straight line from the igniter to the burner (Figure 2). 4. Replace shipping screws if desired. These screws are not necessary for the operation of the burner. They stabilize the burner during shipping of the appliance. Retain the screws for later use in the event the range is moved.

Lig

Burner Support Pilot or Igniter

Show 12 more labels / short text on this page
Gas Valve · Burner Support · Orifice · Air Shutter · Tab · Shipping · Screw · Ports Shipping · Screws · Flash Tube · Support · Brackets
Page 13 of the Kenmore 790.324 user manual — Sealed Burner Models (some models)
Page 13 · click to enlarge
Page 13
Kenmore 790.324 — Sealed Burner Models (some models) diagram (page 13)
Fig. 12 · Sealed Burner Models (some models)

Sealed Burner Models (some models)

To Clean the Burner Grates, Contoured Burner Pans, Burner Cap and Burner Base The burner grates, contoured burner pans, burner caps and burner base should be routinely cleaned. Keeping the burner ports clean will prevent improper ignition and an uneven flame. See instructions below.

To Clean the Burner Grates Be sure burners and grates are cool before you place your hand, a pot holder, cleaning cloths or other material on them. The cast iron burner grates can be washed in hot soapy water. Rinse thoroughly and dry the grates with a cloth; don't put them on the cooktop while still wet. Be sure the grates are positioned securely over the burners.

To remove burned on food, place the grates in a covered container or plastic bag. Add 1/4 cup ammonia and soak for 30 minutes. Wash, rinse well and dry. An abrasive cleaner can be used for stubborn stains.

Burner grate can appear in

different shapes.

To Clean the Contoured Burner Pans

The burner pans are removable from the cooktop. The burner pan forms a recessed well area located around each burner unit. If spill occurs on it, after the burners are turned off, rinse with water and wipe dry.

To Clean the Burner Cap Remove burner cap. Use soap-filled pad or mild abrasive cleanser to clean burner caps. If necessary, cover stubborn spots with an ammonia-soaked paper towel for 30 minutes. Rub gently with a mixture of clean water and vinegar. Wipe dry. Remove all cleaners or the porcelain may become damaged

during future heating.

To Clean the Removable Burner Base and Gas Opening (some models) The ports (or slots) around the burner base must be routinely cleaned. Use a small-gauge wire or needle to clean small slots or holes.

For proper flow of gas and ignition of the burner - DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER THE GAS OPENING TUBE. Gas must flow freely through the small hole in the brass orifice for the burners to light properly. If the gas opening orifice becomes soiled or clogged, use a small-gauge or needle to clean. ALWAYS keep the burner cap in place whenever a surface burner is in use.

To Replace the Burner Base and the Burner Cap Make sure the pieces are thoroughly dry before placing back. 1. Replace burner base and burner cap in their places. Make sure each burner cap and burner base are properly aligned and leveled. 2. Replace the burner grate. 3. Turn the burner on to determine if it lights, if the burner does not light after cleaning, contact a Sears or other qualified service dealer. Do not service the sealed burner yourself.

Burner Cap · ) · Locating Rin(

Page 14 of the Kenmore 790.324 user manual — OCCURRENCE POSSIBLE CAUSE/SOLUTION
Page 14 · click to enlarge
Page 14
Kenmore 790.324 — Before You Call diagram (page 14)
Fig. 13 · Before You Call

Before You Call

Solutions to Common Problems

Before you call for service, review this list. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance.

OCCURRENCE POSSIBLE CAUSE/SOLUTION

Surface burners do not light. Surface Control knob has not been completely turned to LITE. Push in and turn the Surface Control knob to LITE until burner ignites and then turn control to desired flame size.

Be sure gas supply valve is open.

Gas-air mixture needs a straight line to travel. Be sure burner is properly seated in its support (models with open burners only).

Burner ports or slots are clogged. With the burner off, use a small-gauge wire or needle to clean ports or slots.

Power cord is disconnected from outlet (electric ignition models). Be sure cord is plugged securely into outlet.

Electrical power outage (electric ignition models). Burners can be lit manually. See Setting Surface Controls in this Use & Care Guide.

Surface burner flame burns half way around.

Burner ports or slots are clogged. With the burner off, clean ports with a small- gauge wire or needle to clean ports or slots.

Moisture is present after cleaning. Lightly fan the flame and allow burner to operate until flame is full. To avoid this occurrence dry the burners thoroughly following instructions under General Care & Cleaning.

Surface burner flame is orange.

Dust particles in main line. Allow the burner to operate a few minutes until flame turns blue.

In coastal areas, a slightly orange flame is unavoidable due to salt air.

Page 16 of the Kenmore 790.324 user manual — Au Canada pour service en fran£ais: 1-800-LE-FOYER M°
Page 16 · click to enlarge
Page 16
Kenmore 790.324 — Your Home diagram (page 16)
Fig. 14 · Your Home

Your Home

For expert troubleshooting and home solutions advice:

www.managemyhome.com

For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it!

For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.

For Sears professional installation of home appliances and items like garage door openers and water heaters.

1-800-4-MY-HOME ® (1-800-469-4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment, and electronics, call anytime for the location of your nearest

Sears Parts & Repair Service Center

1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada) www.sears.com www.sears.ca

To purchase a protection agreement on a product serviced by Sears:

1-800-827-6655 (U.S.A.)

1-800-361-6665 (Canada)

Para pedir servicio de reparaci6n a domicilio, y para ordenar piezas: 1-888-SU-HOGAR ®

Au Canada pour service en fran£ais: 1-800-LE-FOYER M°

www.sears.ca

® Registered Trademark / TM Trademark / sM Service Mark of Sears Brands, LLC SM ® Marca Registrada / TM Marca de F&brica / Marca de Servicio de Sears Brands, LLC MD MCMarque de commerce / Marque depos6e de Sears Brands, LLC © Sears Brands, LLC

(1-800-533-6937) · (1-888-784-6427)

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Kenmore 790.324

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Kenmore 790.324

Be the first to ask — other owners or our team will answer.

Original document

Kenmore 790.324 manual PDF

16 pages·3.3 MB·Cooktop·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…