Instruction/ maintenance manual of the product 721.80403 Kenmore
Go to page of 18
IVlodels/lViodelos 721.80402 721.80403 721.80404 721.80409 721.80522 721.80523 721.80524 721.80529 Read and save these installation instructions. Lea y guarde estas instrucciones de instalaci6n INSTRUCTIONS p _rowave Hood Combination Combinaci6n Microondas Campana 0 i=.
YOUR SAFETY FIRST BEFORE YOU START • Proper installation is the installer's responsibility! - Read the entire manual before you begin. - The model number label is located on the oven front. See Figure 1. - Mounting plate is located on back side of microwave oven.
YOUR SAFETY FIRST • THIS APPLIANCE MUST BE GROUNDED! - If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug.
YOUR SAFETY FIRST • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. - Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.
PARTS, TOOLS, MATERIALS THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts.
PARTS, TOOLS, MATERIALS YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION: Carton or other heaw material for covering the counter top.
STEP 1: PREPARE THE ELECTRICAL CONNECTIONS _k WARNING _k AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 4 Detail. NOTE: The outlet should be on a circuit dedicated to the microwave oven 120V, 60Hz.
STEP 2: PREPARE THE VENTING S YSYTEM NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 9, page 9.
STEP 2: PREPARE THE VENTING S YSYTEM STANDARD FITTINGS NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper sticking.
STEP 3: PREPARE THE VENTING BLOWER Your microwave oven is shipped with the blower assembled for room venting (recirculating). You need to adjust the blower if you want wall vented or roof vented installation. A. WARNING _k ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT.
STEP 3: PREPARE THE VENTING BLOWER WALL VENTED INSTALLATION: 1. Remove two blower unit mounting screws and one or two blower plate screws. Remove the blower plate from cabinet. See Figure 12. 2. Carefully lift the blower unit out of the microwave oven.
STEP 3: PREPARE THE VENTING BLOWER ROOF VENTED INSTALLATION: 1. Remove two blower unit mounting screws and one or two blower plate mounting screws. Remove the blower plate from cabinet. See Figure 18. blower plate mounting screws 2. Carefully lift the blower unit out of the microwave oven.
STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION MEASURE AND TACK / TAPE UP THE TEMPLATE 1. Using a plumb line and (metal) measuring tape, find and mark the vertical center line (_ on the back wall, as in Figure 22. 2. Find and mark one or two points where the studs are on the wall (Studs are normally 16 inches apart.
STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION DRILL THE HOLES IN THE WALL AND UPPER CABINET. A, WARNING _, BE VERY CAREFUL WHEN DRILLING HOLES INTO THE WALL. Electrical wires could be concealed behind the wall covering and if the drill hits them you could get an electric shock.
STEP 5: INSTALL THE MOUNTING PLATE TO THE WA L L THE OVEN MUST BE CONNECTED TO AT LEAST ONE WALL STUD. 1. Draw a vertical line on the wall at the center of the 30" wide space. Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are against the bottom of the cabinet.
STEP 5: INSTALL THE MOUNTING P L ATE TO THE WA L L TO PREPARE THE REAR WALL CUTOUT OPENING AND EXHAUST ADAPTOR/MOUNTING PLATE FOR WALL VENTING AND ROOF VENTING: NOTE: If room vented installation is used, skip this step. 1. Place the mounting plate against the rear wall as described in step 5 item 1 (page 15).
STEP 6: ATTACH THE OVEN TO THE WALL _k WARNING A, You will need two people to lift this microwave. Failure to use more than one person could result in personal injury. 1. Carefully lift microwave oven and hang it on support tabs (See Figure 26) at the bottom of the mounting plate.
STEP 6: ATTACH THE OVEN TO THE WALL 5. Roof vented installation: See Figure 32. Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the roof according to the method needed. See "PREPARE THE VENTING SYSTEM," STEP 2 on the page 8.
An important point after buying a device Kenmore 721.80403 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kenmore 721.80403 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kenmore 721.80403 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kenmore 721.80403 you will learn all the available features of the product, as well as information on its operation. The information that you get Kenmore 721.80403 will certainly help you make a decision on the purchase.
If you already are a holder of Kenmore 721.80403, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kenmore 721.80403.
However, one of the most important roles played by the user manual is to help in solving problems with Kenmore 721.80403. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kenmore 721.80403 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
