Instruction/ maintenance manual of the product 625.38376 Kenmore
Go to page of 48
Sears, Roebuck and Co., 3333 Beverly Road, Hoffman Est ates, IL 60179 USA PRINTED IN U.S.A. Part No. 7282603 (Rev . E 12/8/06) • W arranty • Installation • S tart Up / Setting T imer • How It W orks • Care Of • S pecifications • Repair Part s W ater Sof teners With High Performance V alve www .
2 Questions? Call The Kenmore W ater Line 1-800-426-9345 W ARRANTY ON W A TER SOFTENER ONE YEAR LIMITED W ARRANTY ON W A TER SOFTENER When installed, operated and maint ained according to all instruct.
3 T ABLE OF CONTENTS Safety Guides ................................................................................................................. ................................ 4 Unpack and Check Shipment .........................................
4 Y Read all steps, guides and rules carefully before inst alling and using your new water softener . Follow all steps exactly to correctly inst all. Failure to follow them could cause personal injury or property damage. Reading this book will also help you to get all of the benefits from your water softener .
5 Unpac k and Chec k Y our Car ton FIG . 1 Questions? Call The Kenmore W ater Line 1-800-426-9345 Packing List INSPECT SHIPMENT Y our water softener is shipped complete in one carton. Use care when handling the softener . DO NOT turn upside down. DO NOT drop, or set on sharp objects that could make a hole in the bottom.
6 Plan Y our Installa tion PLAN YOUR INST ALLA TION It is recomended to read through the entire manual before beginning your installation. Follow all step s exactly .
7 Plan Y our Installa tion T ypical Inst allation 1. Place as close as possible but always after , the pressure tank (well water) or water meter (city water). See Fig. 3. 2. Place as close as possible to a water drain such as a floor drain, laundry tub, sump or stand pipe.
8 Plan Y our Installa tion Suggested Slab Foundation Inst allation Plug the softener transformer into an inside, 120 volt 60Hz electrical outlet. If an outside outlet is used, be sure it has approved weather protection. Run drain tubing to laundry tub or p-trap inside home, if possible.
9 PIPE, FITTINGS, OTHER MA TERIALS NEEDED Y ou must first decide how to run “in” and “out” pipes to the softener . Look at your house main water pipe at the point you will connect the softener .
10 R ead Before Be ginning Installation BEFORE INST ALLING CHECKS & TESTS Y our water supply needs to be checked for chemical analysis, water pressure and water flow rate.
11 FIG . 9 INST ALLING BYP ASS V AL VE, AND/OR INLET AND OUTLET THREADED ADAPTORS Clip (2) V alve Outlet Included with Softener Included with Softener V alve Inlet ASSEMBLE INLET OUTLET ADAPTORS, OR PLASTIC BYP ASS V AL VE Complete the following steps to assemble the adaptors or bypass valve.
12 Install 3-V alv e Bypass INST ALLING 3 V AL VE BYP ASS AND PIPES Complete the following steps to inst all the three (3) valve bypass: • Cut the house main water pipe where you will con- nect the softener . • Loosely put together pipe, fittings, and the three (3) valves.
13 Loca te W a ter Softener and Connect Pipes MOVE SOFTENER INTO PLACE Grip under ridge to move softener . Plywood Shims TYPICAL SOLDERING CONNECTIONS Main W ater Pipe Hard W ater 1. Cut pipe to correct length. 2. Solder (WHEN COOL, do S tep 3). 3. Put threaded adaptor into bypass valve port.
14 Connect V alv e and Salt T ank Dr ains CONNECT THE V AL VE DRAIN HOSE T ake a length of 3/8” inside diameter drain tubing and attach one end to the drain fitting. See Fig. 16. Use a tube clamp to hold it in place. Put the other end of the tubing over a floor drain, into a laundry tub, stand pipe, or other suitable drain.
15 Leak T est LEAK TEST T o check for leaks, complete the following steps: CAUTION: T o avoid water or air pressure dam- age to softener inner parts, and to flush pipe chips or other residue from the water pipes, be sure to do the following steps exactly as instructed.
16 Electrical R equir ements INST ALL GROUNDING CLAMP BETWEEN THE SOFTENER IN AND OUT PIPES The house cold water pipe (iron or copper) is often used to ground all electrical outlets in the home. Outlets are grounded to protect you from shock when you touch any electric appliance plugged into the out- let.
17 Pr og r am T he Timer Display Salt Level Adjust Signal Light Adjust T ank Light DOWN Button UP Button REGENERA TION Button SELECT Buttons PRESENT TIME AM SAL T LEVEL SIGNAL LEVEL SAL T LEVEL SIGNAL.
18 Pr og r am T he Timer SET PRESENT TIME OF DA Y If the words PRESENT TIME do not show in the display , press the SELECT1 button until they do show in the dis- play . Press the UP or DOWN buttons to set the present time. Press UP to move the display ahead; press DOWN to move the time backward.
19 Sanitize T he W ater Softener SANITIZE THE W A TER SOFTENER Care is taken at the factory to keep your water sof tener clean and sanitary . Materials used to make the softener will not infect or contaminate your water supply , or cause bacteria to form or grow .
20 Adding Salt T o T he Stor a ge T ank ADDING SAL T TO THE STORAGE T ANK Brine (salt dissolved in water) is needed for each and every regeneration. The water for making brine is metered into the salt storage tank by the sof tener .
21 Chec k List CHECK LIST OF STEP-BY -STEP GUIDES T O INST ALL Review the following list to ensure you have completed all the installation procedures. ____1. Check the incoming water . Has incoming water been tested? ____2. Remove cardboard packaging from salt t ank.
22 5. If you wish to turn the salt monitor off, press the SET LOW SAL T LIGHT button until OFF shows above. NOTE: Y our salt monitor is an estimate of your salt level; accuracy depends on the type of salt used and other regeneration characteristics.
23 F aceplate Timer F ea tur es OPTIONAL SETTINGS: • SAL T EFFICIENCY • CLEAN FEA TURE • CLEAN FEA TURE MINUTES • INTELLISOFT 97% FEA TURE • 12 / 24 HOUR CLOCK • GALLONS / LITERS • MAXIMUM DA YS BETWEEN REGENERA TIONS 1.
24 F aceplate Timer F ea tur es 4. Press SELECT1 to show the 97% Feature. IntelliSof t 97% Feature: The 97% Feture is an inte- gral part of the IntelliSof t water and salt saving sys- tem. When this feature is ON, the softener will auto- matically recharge when 97% capacity has been used, at any time of day .
A VG. DAIL Y GALLONS PM SAL T LEVEL SIGNAL LEVEL 8 7 6 5 4 3 2 1 FIG . 45 25 F aceplate Timer F ea tur es FIG . 46 A VERAGE DAIL Y GALLONS or LITERS Press the SELECT 2 button again to show the average number of gallons (or liters) of soft water the household uses each day .
26 Ho w Y our W a ter Softener W or ks FIG . 50 SOFT W A TER SER VICE AND REGENERA TION SERVICE When the softener is giving you sof t water , it is called “Service”. During service, hard water comes from the house main water pipe into the softener .
27 Ho w Y our W a ter Softener W or ks SOFT W A TER SER VICE AND REGENERA TION BRINING: During brining, the brine is moved from the salt storage area, into the resin tank. Inside the resin tank, brine cleans hardness minerals from the resin beads and they are discharged out the drain.
28 Ho w Y our W a ter Softener W or ks F AST RINSE: Backwash is followed by a fast flow of water down through the resin tank. The fast flow packs the resin bed and gets it ready for return to service. After fast rinse, the sof tener returns to service.
29 Car e Of Y our W a ter Softener FIG . 54 SAL T BRIDGE Sometimes, a hard crust or salt bridge forms in the salt storage tank. It is usually caused by high humidity or the wrong kind of salt. When the salt bridges, an empty space forms between the water and salt.
30 Car e Of Y our W a ter Softener FIG . 55 KEEPING THE W A TER SOFTENER CLEAN NOZZLE & VENTURI A clean nozzle and venturi (see Fig. 55) is a must for the softener to work right. This small unit moves brine from the salt storage tank to the resin t ank during regeneration.
31 Car e Of Y our W a ter Softener PROTECT THE W A TER SOFTENER FROM FREEZING If the softener is inst alled where it could freeze (sum- mer cabin, lake home, etc.), you must drain all water from it to stop possible freeze damage. T o drain the sof- tener: 1.
32 Car e Of Y our W a ter Softener CHECKLIST TO HELP YOU SA VE MONEY If your water softener fails to work, make the following easy checks. Of ten, you will find what is wrong yourself and you won’t have to call and wait for service.
33 Specifica tions FIG . 57 Questions? Call The Kenmore W ater Line 1-800-426-9345 A B C D E F Inches CM A Salt T ank Height 40-1/4 102.2 B Resin T ank Diameter (nominal) 9 22.9 C Resin T ank Height (nominal) 40 101.6 D Inlet-Outlet Height 41-1/2 105.
34 Specifica tions FIG . 58 Questions? Call The Kenmore W ater Line 1-800-426-9345 Intermittent flow rate does not represent the maximum service flow rate used for determining the soften- ers rated capacity and ef ficiency . Continuous operation at flow rates greater than the service flow rate may affect cap acity and efficiency performance.
35 Ser vice T ec h Inf or ma tion FIG . 59 Keep this manual with your water softener . If repairs are needed, the service technician must have the informa- tion on the following pages. AL W A YS MAKE THESE INITIAL CHECKS FIRST 1. Does the time display show the correct time of day? • If display is blank, check power source to the sof- tener .
36 Ser vice T ec h Inf or ma tion FIG . 60 The faceplate timer (PW A) computer has a self-diag- nostic function for the electrical system, except put power and water meter . The computer monitors elec- tronic components and circuit s for correct operation.
37 Ser vice T ec h Inf or ma tion TROUBLESHOOTING V AL VE POSITION INDICA T ORS: Depending on the valve position, the following indica- tors show in the display: Indicator V alve Position Serv ..................................... Service Fill........
38 Ser vice T ec h Inf or ma tion MANUAL ADV ANCE REGENERA TION CHECK This check verifies proper operation of the valve motor , brine tank fill, brine draw , regeneration flow rates, and other controller functions. Always make the initial checks, and the manual initiated diagnostics.
39 Ser vice T ec h Inf or ma tion ROT ARY V AL VE SERVICE IMPORT ANT : Before working on the valve, turn off the water supply and disconnect from electrical power . TO RELIEVE PRESSURE: • 3 V AL VE BYP ASS: Close the inlet valve and open a soft water faucet.
40 FIG . 69 Drain from valve inlet (Hard W ater) Bypass Hard W ater T o V alve Outlet Position Switch BRINING AND BRINE RINSE CYCLE Brine from Salt S torage T ank Nozzle V enturi Ser vice T ec h Inf or ma tion SERVICE CYCLE Hard water enters the valve inlet port.
41 Ser vice T ec h Inf or ma tion Drain Bypass Hard W ater T o V alve Outlet Position Switch BACKW ASH CYCLE Flow Plug FIG . 70 Questions? Call The Kenmore W ater Line 1-800-426-9345 BACKW ASH CYCLE T imer/switch action again allows the motor to turn the rotor & disc to place the valve in BACKW ASH, stopping water flow to the nozzle.
42 4 3 1 2 29 30 31 5 6 28 27 7 Rating Decal Location 8 26 25 24 23 22 21 20 9 10 11 12 13 14 18 17 16 19 15 Kenmore MODEL Nos. 625.383760 and 625.393760 Exploded V iew Questions? Call The Kenmore W a.
43 P ar ts List Kenmore MODEL Nos. 625.383760 and 625.393760 A. W A TER SOFTENER COMPLETE Key No. Part Number Part Description 1 ---- Cover Lock (Required for shipping only) 1 ---- Rim Insert (Require.
44 Exploded V iew 19 18 17 1 2 3 4 5 6 7 8 9 16 15 14 13 12 10 20 11 INLET - OUTLET GROUNDING CLAMPS Kenmore MODEL Nos. 625.383760 and 625.393760 Questions? Call The Kenmore W ater Line 1-800-426-9345.
45 P ar ts List Kenmore MODEL Nos. 625.383760 and 625.393760 B. BRINE V AL VE ASSEMBL Y Key No. Part Number Part Description 1 7168647 Ceramic Weight 2 0513860 Float S top 3 7097202 Float (includes Key No.
46 Exploded V iew 1 48 2 3 4 5 6 7 47 8 9 10 11 46 12 21 13 14 15 16 17 44 45 30 28 43 42 41 40 39 38 37 36 35 29 33 31 32 20 25 26 27 Seal Wear-S trip 22 23 24 18 19 Cross-Section View 34 Questions? .
47 P ar ts List Key Part No. Number Part Description 1 7224087 Screw , #8-32 x 1" (2 req.) 2 7286039 Motor (incl. 2 ea. of Key No. 1) 3 7288201 Motor Plate 4 0900857 Screw , #6-20 x 3/8" (3 req.
® Registered Trademar k / TM Tradema rk / SM Service Mark of Sear s Brands, LLC ® Mar ca Reg istra da / TM Mar ca de Fábr ica / SM Marca de Servicio de Sears Brands, LLC MC Marque de commer ce / MD.
An important point after buying a device Kenmore 625.38376 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kenmore 625.38376 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kenmore 625.38376 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kenmore 625.38376 you will learn all the available features of the product, as well as information on its operation. The information that you get Kenmore 625.38376 will certainly help you make a decision on the purchase.
If you already are a holder of Kenmore 625.38376, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kenmore 625.38376.
However, one of the most important roles played by the user manual is to help in solving problems with Kenmore 625.38376. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kenmore 625.38376 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
