Instruction/ maintenance manual of the product AGC2 Andis Company
Go to page of 20
USE AND CARE MODEL AGC2 LITERATURE PACKET #04959 Item pictured may differ from actual product El artículo ilustrado puede diferir del producto real Il est possible que l’article sur la photo soit d.
2 ENGLISH Congratulations – you just went first class when you bought this Andis product. Careful workmanship and quality design have been the hallmarks of Andis products since 1922.
3 8. Do not use this appliance with a damaged or broken blade or comb, as injury to the skin may occur . 9. T o disconnect turn control to “off” then remove plug from outlet. 10. WARNING: During use, do not place or leave appliance where it may be (1) damaged by an animal or (2) exposed to the weather .
4 DIAGRAM D DIAGRAM E DIAGRAM C DIAGRAM B DIAGRAM A DIAGRAM F DIAGRAM G OIL OIL OIL DIAGRAM H DIAGRAM I DIAGRAM J DIAGRAM K BLADE DRIVE MOUNTING SCREWS DIAGRAM L DIAGRAM M CORRECT POSITION OF DRIVE BE.
5 REPLACING OR CHANGING BLADE SET T o replace or change your blade set, slide the blade bracket onto the hinge of the clipper (Diagram F) and with the clipper turned “ON”, push the blade towards the clipper to lock into position. USER MAINTENANCE The internal mechanism of your motor clipper has been permanently lubricated by the factory .
6 then place a drop of clipper oil where the upper and lower blades meet and also in the guide slot of the tension spring (Diagram H). Now slide the upper blade to the opposite side of the lower blade and repeat this process. After completing this procedure, slide the upper blade, centering it over the lower blade.
7 ¡Felicidades! Al adquirir este producto Andis, usted ha hecho una compra de primera clase. T rabajo esmerado y diseños de calidad han distinguido a los productos Andis desde 1922.
8 5. Mantenga el cable lejos de superficies calientes. 6. Nunca deje caer el aparato ni inserte ningún objeto en ninguna de sus aberturas. 7. No lo utilice al aire libre, ni lo opere donde se estén usando pro du cto s en aerosol (nebulizados) o donde se esté administrando oxígeno.
9 DIAGRAMA D DIAGRAMA E DIAGRAMA C DIAGRAMA B DIAGRAMA A DIAGRAMA F DIAGRAMA G DIAGRAMA H DIAGRAMA I DIAGRAMA J DIAGRAMA K DIAGRAMA L DIAGRAMA M DIAGRAMA N DIAGRAM O TORNILLOS DE MONTAJE DEL ACCIONAMI.
10 DESMONT AJE DEL JUEGO DE HOJAS Para desmontar el juego de hojas, asegúrese primero de que el motor de la recortadora esté colocado en la posición “OFF”. Presione el mecanismo de liberación de la hoja debajo de la bisagra de la hoja (Diagrama B).
11 CUIDADOS Y SERVICIO A LAS HOJAS ANDIS Debe lubricar las hojas antes, durante y después de cada uso. Si las hojas de su recortadora dejan líneas o reducen su velocidad, significa que requieren de lubricación. Debe sostener la recortadora en la posición que se muestra para evitar que el aceite entre al motor .
12 4. NOT A: Antes de desmontar el conjunto de accionamiento de las hojas, observe la manera en que esté colocado (esto le ayudará al volver a armarlo).
13 T outes nos félicitations pour l’achat de cet appareil, un produit Andis de première classe. La qualité de fabrication et de conception est l’apanage des produits Andis depuis la fondation de la société en 1922.
14 6 . Ne jamais insérer un objet quelconque dans une ouverture de l’appareil. 7. Ne pas utiliser l’appareil à l’extérieur , dans un endroit où des aérosols sont employés ou encore dans un endroit où l’on administre de l’oxygène.
15 ILLUSTRA TION D ILLUSTRA TION E ILLUSTRA TION C ILLUSTRA TION B ILLUSTRA TION F ILLUSTRA TION H ILLUSTRA TION I ILLUSTRA TION J ILLUSTRA TION L ILLUSTRA TION O ILLUSTRA TION K VIS DE FIXA TION DU M.
16 RETRAIT DU JEU DE LAMES Avant de retirer le jeu de lames, s’assurer que le moteur de la tondeuse est arrêté. Pousser le mécanisme de libération des lames sous la charnière des lames (illustration B).
17 tondeuse Andis sur l’avant et le côté des têtes de coupe (Figure I). Essuyer l’excès d’huile avec un chiffon doux et sec. Les lubrifiants en aérosol ne permettent pas d’appliquer suffisamment d’huile pour lubrifier correctement les lames, mais ce sont d’excellents agents de refroidissement pour tondeuse.
18 6. Installer le nouveau mécanisme d’entraînement, aligner les trous de vis et appuyer (illustration L). 7. Fixer le mécanisme d’entraînement avec les vis de fixation (illustration K). 8. Remettre le capuchon d’entraînement (illustration J).
19.
Form #100001 © 20 1 3 A ndis C omp an y , U.S .A . Printed in U.S.A. ANDIS COMP ANY 1800 Renaissance Blvd. Sturtevant, WI 53177 1-800-558-9441 Canada: 1-800-335-4092 info@andisco.
An important point after buying a device Andis Company AGC2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Andis Company AGC2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Andis Company AGC2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Andis Company AGC2 you will learn all the available features of the product, as well as information on its operation. The information that you get Andis Company AGC2 will certainly help you make a decision on the purchase.
If you already are a holder of Andis Company AGC2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Andis Company AGC2.
However, one of the most important roles played by the user manual is to help in solving problems with Andis Company AGC2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Andis Company AGC2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
