Instruction/ maintenance manual of the product RX-5001VGD JVC
Go to page of 30
For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference.
W arnings, Cautions and Others / A visos, precauciones y otras notas / Advertêcias, precauções e outras notas / G-1 CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture.
G-2 Español English Português Caution: Proper V entilation T o avoid risk of electric shock and fire and to protect from damage. Locate the apparatus as follows: Front: No obstructions open spacing. Sides: No obstructions in 10 cm from the sides. T op: No obstructions in 10 cm from the top.
1 English T able of Contents Parts Identification ...................................... 2 Getting Star ted ........................................... 3 Before Installation ...................................................................... 3 Checking the Supplied Accessories .
2 English Par ts Identification Become familiar with the buttons and controls on the receiver before use. Refer to the pages in parentheses for details.
3 English ANTENNA AM EXT AM LOOP FM 75 COAXIAL AM LOOP ANTENNA AM EXT FM 75 COAXIAL AM LOOP ANTENNA AM EXT FM 75 COAXIAL Getting Star ted This section explains how to connect audio/video components and speakers to the receiver , and how to connect the power supply .
4 English RIGHT LEFT REAR SPEAKERS CENTER SPEAKER T urn the loop until y ou have the best r eception. Notes: • Make sure the antenna conductors do not touch an y other ter minals, connecting cords and power cord. This could cause poor reception. • If reception is poor , connect an outdoor single vinyl-cov ered wire to the AM EXT ter minal.
5 English Connecting the subwoofer speaker Y ou can enhance the bass by connecting a subwoofer . Connect the input jack of a powered subwoofer to the SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs.
6 English VIDEO AUDIO LEFT RIGHT MONITOR OUT OUT (REC) IN (PLA Y) OUT (REC) IN (PLA Y) DVD VCR VHS Video component connections Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the audio right jack and the yellow plug to the video jack.
7 English Putting Batteries in the Remote Control Before using the remote control, put two supplied batteries first. When using the remote control, aim the remote control directly at the remote sensor on the receiv er . 1. On the back of the remote contr ol, remo ve the battery cover as illustrated.
8 English T urning the Power On and Off (Standby) On the front panel: T o turn on the power , press ST ANDBY/ON . The ST ANDBY lamp goes of f. The name of the current source (or station frequency) appears on the display . T o turn off the po wer (into standby mode), press ST ANDBY/ON again.
9 English Adjusting the V olume On the front panel: T o increase the v olume, turn MASTER V OLUME clockwise (+). T o decr ease the volume, turn it counterclockwise (–). • When you turn MASTER V OLUME rapidly , the volume le vel also changes rapidly .
10 English Attenuating the Input Signal When the input le vel of the playing source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal lev el to prev ent the sound distortion. On the front panel ONL Y : Press INPUT A TT .
11 English Changing the Source Name When you hav e connected an MD recorder to the T APE/MD jacks on the rear panel: Change the source name sho wn on the display when you select the MD recorder as the source. On the front panel ONL Y : When changing the source name from “T APE” to “M D”: 1.
12 English T o store the sound settings 1. Press ONE T OUCH OPERA TION. The ONE T OUCH OPERA TION lamp lights up, then the previously memorized settings are recalled. 2. Adjust the sound using the functions listed to the left. The ne wly adjusted settings are memor ized.
13 English Setting the AM T uner Interval Spacing Some countries space AM stations 9 kHz apart, and other countries use 10 kHz spacing. When shipped, the spacing is set to 9 kHz. On the front panel ONL Y : T o select the 10 kHz interv al: Be sure the receiv er is tuned off, b ut is plugged into an A C outlet.
14 English Selecting the FM Reception Mode When an FM stereo br oadcast is har d to receive or noisy Y ou can change the FM reception mode while receiving an FM broadcast. On the front panel ONL Y : 1. Press FM. The last station of the selected band is tuned in.
15 English Using the DSP Modes The built-in Surround Processor provides three types of the DSP (Digital Signal Processor) mode — 3D-PHONIC mode, DAP (Digital Acoustic Processor) mode and Surround mode (Dolby Pro Logic and JVC Theater Surround). * Manuf actured under license from Dolby Laboratories Licensing Corporation.
16 English Available DSP Modes According to the Speaker Ar rangement A vailable DSP modes will v ary depending on how many speak ers ar e used with this receiv er .
17 English Adjusting the DAP Modes Bef ore you start, r emember ... • Make sur e tha t you ha ve set the speaker inf ormation correctly (see page 11). • There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
18 English From the r emote contr ol: 1. Press SOUND CONTR OL. The 10 keys ar e activa ted for sound adjustments. 2. Press SURR OUND repeatedly until the D AP mode — D ANCE CLUB, LIVE CLUB, HALL, or P A VILION — appears on the display . The D AP indicator also lights up on the display .
19 English 8. ONL Y FOR JVC Theater Surround: Press MUL TI CURSOR @ / # to select an effect lev el you want. • Each time you press the button, the ef fect le vel changes as follows: As the number increases, JVC Theater Surround becomes stronger .
20 English Using the DVD MUL TI Playback Mode This receiver provides the DVD MUL TI playback mode for reproducing the analog discrete output mode of the DVD player . Before playing back a DVD, refer also to the manual supplied with the DVD player . 7.
21 English COMPU LINK Remote Contr ol System The COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor on the receiver .
22 English Operating JVC’ s Audio/V ideo Components Y ou can operate JVC’s audio and video components with this r eceiver’s remote control, since control signals for JVC components are preset in the remote control.
23 English VCR Y ou can always perform the follo wing oper ations : VCR :T urns on or off the VCR. VCR CH +/– : Changes the channels on the VCR. After pressing VCR, you can perform the following operations on the VCR: 3 : Starts playing. 1 : Re winds a tape.
24 English PROBLEM The display does not light up. No sound from speakers. Sound from one speaker only. Continuous hiss or buzzing during FM reception. Occasional cracking noise during FM reception. Howling during record playing. “OVERLOAD” starts flashing on the display.
25 English Specifications Amplifier Output Po wer At Stereo operation: 100 W per channel, min. RMS, both channels driv en into 8 Ω at 1 kHz, with no more than 0.9% total harmonic distortion. (IEC268-3/DIN) At Surround operation: Front Channel: 70 W per channel, min.
26 English FM tuner (IHF) T uning Range: 87.50 MHz to 108.00 MHz Usable Sensiti vity: Monaural: 12.8 dBf (1.20 µV/75 Ω ) 50 dB Quieting Sensiti vity: Monaural: 21.
J V C 0400HIMMDWJEIN EN, SP, PR, CH Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, Australia and U.K.) Instrucción sobre la línea de la red (CA) (no aplicable para Europa, EE.UU., Canadá, Australia, ni el Reino Unido) Instrução sobre a tensão da rede eléctrica (CA) (não aplicável para a Europa, os E.
An important point after buying a device JVC RX-5001VGD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC RX-5001VGD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC RX-5001VGD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC RX-5001VGD you will learn all the available features of the product, as well as information on its operation. The information that you get JVC RX-5001VGD will certainly help you make a decision on the purchase.
If you already are a holder of JVC RX-5001VGD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC RX-5001VGD.
However, one of the most important roles played by the user manual is to help in solving problems with JVC RX-5001VGD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC RX-5001VGD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
