Instruction/ maintenance manual of the product RK-C42WBT3 JVC
Go to page of 16
RK-C42WBT3 Thank you for purchasing this Wall Mounting Unit. We recommend that you read this manual thoroughly before use in order to familiarize yourself with this unit. Please store this manual in a safe place after reading it. • Mounting a plasma display television requires specific technical knowledge.
2 Assembly and Mounting Warnings ● Consult authorized service personnel for the installation and attachment of this unit to the wall. This unit weighs approx. 60 kg (approx. 132 lbs.), including display monitor. Improper assembly or installation may cause the unit to fall when it is mounted, which may result in fatal accidents.
3 W arning Mounting the Wall Unit The Wall Mounting Unit should be mounted to a wall that can adequately hold the total weight of the plasma display and the Wall Mounting Unit over a long period of time and which can adequately withstand earthquakes, conceivable vibrations, and other external forces.
4 Frame Fastening Screws left/right (Spacer Ring + Flat Washer + Spring Washer) Frame Rotation Shaft Screws (left/right) Spacer Rings (left/right) Frame Attachment Lever Screws Angle Adjustment Lever Frame Rotation Jaw Plasma Display w q e X 10 r Angle Adjustment Lever Lock Screw Caution ● Consult authorized service personnel for electrical work.
5 <Before Attaching Plasma Display> 2. Push in the heads of the left and right Frame Removal Lever Screws a and lift up section b to remove the Frame q from the Wall Mounting Unit w . The Wall Mounting Unit is sold with Frame q and Wall Mounting Unit w fixed together.
6 Instructions for Assembly 1. Attach the Wall Mounting Unit w to the surface of the wall. The unit should be attached using the method most suited to the wall structure.
7 3. Identify the Rotation Shaft Screws of the Wall Mounting Unit. Check that the left and right Rotation Shaft Screws are secure, as the Rotation Jaw of the Frame (attached to the plasma display) will be inserted into the Rotation Shaft Screw Component of the Wall Mounting Unit w .
8 5. Fix the Frame and Wall Mounting Unit. Combine the Frame Fastening Screws, Spacer Rings, Flat Washers, and Spring Washers (from the two pairs of Frame Fastening Screw Components that were put aside when detaching the Frame q from the Wall Mounting Unit w ) as shown below and fasten them securely using a screwdriver.
9 <Instructions for Assembly, cont’d> Adjusting the Angle of the Plasma Display ＊ The angle of the Wall Mounting Unit can be adjusted to 0 ° , 5 ° , 10 ° , 15 ° , and 20 ° .
10 2. Place one hand on top of the plasma display to steady it and with the other hand set the Angle Adjustment Lever to 20 ° . ＊ If the Angle Adjustment Lever has already been fastened, perform this task after removing the Angle Adjustment Lever Lock Screw.
11 <Instructions for Assembly, cont’d> 3. Remove the Rotation Shaft Screws and Spacer Rings at the bottom left and right of the Wall Mounting Unit. ＊ The Rotation Shaft Screws and the Spacer Rings will be used after the cables have been connected.
12 Brace the plasma display while connecting the power cord or system cables, as the display may tip over, causing injury. 5. Connect the power cable and system cables to the plasma display. ＊ Be careful not to let the cables become caught between the plasma display and the Wall Mounting Unit.
13 7. Set the angle of the plasma display. Hold the upper part of the plasma display with one hand and set the display to the desired angle with the other hand, using the Angle Adjustment Lever on the Wall Mounting Unit. 8. Fasten the Angle Adjustment Lever.
14 1. Hold the upper middle of the plasma display and set the Angle Adjustment Lever to 0 ° . ＊ If the Angle Adjustment Lever has been fastened, remove the Angle Adjustment Lever Lock Screw before performing this task. This task must be performed by at least two persons.
15 <Instructions for Removing the Plasma Display, cont’d.> This task must be performed by at least two persons. Danger 3. Remove the Frame Fastening Screws, Spacer Rings, Flat Washers, and Spring Washers of the two Frame Fastening Screw Components at the upper left and right of the Wall Mounting Unit.
Wall Mounting Unit Exterior 13 1 20 13 13 13 1 20 13 1 20 13 13 13 1 20 2-φ5 2-φ8 2-φ5 2-φ8 2-φ5 2-φ8 2-φ5 2-φ8 2-φ5 2-φ5 2-φ8 20 89 49 20° 300 20 20 8.
An important point after buying a device JVC RK-C42WBT3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC RK-C42WBT3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC RK-C42WBT3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC RK-C42WBT3 you will learn all the available features of the product, as well as information on its operation. The information that you get JVC RK-C42WBT3 will certainly help you make a decision on the purchase.
If you already are a holder of JVC RK-C42WBT3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC RK-C42WBT3.
However, one of the most important roles played by the user manual is to help in solving problems with JVC RK-C42WBT3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC RK-C42WBT3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
