EN
JVC logo
Official user manual

JVC HM-HDS1U

100 pages·5.4 MB·MP3 Player·PDF·ENDEFRITNLJA
JVC HM-HDS1U
Table of Contents 19 sections CONTENTS · INSTALLING YOUR NEW RECORDER · INITIAL SETTINGS · SIMPLE OPERATION for HDD deck · … ShowHide
Page 1 of the JVC HM-HDS1U user manual — LPT0585-001A
Page 1 · click to enlarge
Page 1

HDD / VHS DUAL RECORDER

HM-HDS1U

JVC HM-HDS1U — HDD / VHS DUAL RECORDER diagram (page 1)
Fig. 1

For Customer Use:

INSTRUCTIONS

Enter below the Model No. and Serial No. which are located on the rear of cabinet. Retain this information for future reference. Model No. Serial No.

LPT0585-001A

> < · – +

Page 2 of the JVC HM-HDS1U user manual — **ABOUT HEAD CLEANING
Page 2 · click to enlarge
Page 2

Dear Customer, Thank you for purchasing the JVC VHS video cassette recorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new recorder.

Failure to heed the following precautions may result in damage to the recorder, remote control or video cassette.

CAUTIONS

1. DO NOT place the recorder in an environment prone to extreme temperatures or

CAUTION

RISK OF ELECTRIC SHOCK

humidity in direct sunlight in a dusty environment in an environment where strong magnetic fields are

DO NOT OPEN

DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

generated on a surface that is unstable or subject to vibration. 2. DO NOT block the recorder’s ventilation openings. 3. DO NOT place heavy objects on the recorder or remote control. 4. DO NOT place anything which might spill on top of the recorder or remote control. 5. AVOID violent shocks to the recorder during transport.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

**MOISTURE CONDENSATION

Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form on the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the recorder’s power turned on for a few hours to let the moisture dry before inserting a tape.

**ABOUT HEAD CLEANING

Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or inter- rupted. Be sure to contact your nearest JVC dealer if such troubles occur.

VCR Plus+, C3 and PlusCode are registered trademarks of Gemstar Development Corporation. The VCR Plus+ system is manufactured under license from Gemstar Development Corporation.

DSSTM is an official trademark of DIRECTV, Inc., a unit of GM Hughes Electronics. PRIMESTAR is a registered service mark of Primestar Partners, L.P. DISH NetworkTM is a trademark of Echostar Communications Corporation.

Cassettes marked “S-VHS“ and “VHS” can be used with this

recorder. However, S-VHS recordings are possible only with cassettes marked “S-VHS“. By using S-VHS ET it is possible to record and play back with S-VHS picture quality on VHS cassettes with this recorder.

This product incorporates copyright protection technology that is protected by method claimes of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing users only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Page 3 of the JVC HM-HDS1U user manual — INSTALLATION
Page 3 · click to enlarge
Page 3

EN 3 IMPORTANT PRODUCT SAFETY INSTRUCTIONS

2. Power Sources Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.

Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.

3. Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
4. Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
  • 5. Ventilation Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.
  • Do not block the openings by placing the product on a bed, sofa, rug or other similar surface.
  • Do not place the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

INSTALLATION

1. Grounding or Polarization (A) Your product may be equipped with a polarized alternating-

current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. (B) Your product may be equipped with a 3-wire grounding-type

plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

6. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
Page 4 of the JVC HM-HDS1U user manual — NEC – NATIONAL ELECTRICAL CODE
Page 4 · click to enlarge
Page 4

ANTENNA INSTALLATION INSTRUCTIONS

USE

  • 1. Accessories To avoid personal injury:
  • Do not place this product on an unstable cart, stand, tripod, bracket, or table. It may fall, causing serious injury to a child or adult, and serious damage to the product.
  • Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.
  • Use a mounting accessory recommended by the manufacturer and follow the manufacturer’s instructions for any mounting of the product.
  • Do not try to roll a cart with small casters across thresholds or deep-pile carpets.

1. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/ NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connec- tors, location of antenna discharge unit, connection to ground- ing electrodes, and requirements for the grounding electrode.

2. Lightning For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
2. Product and Cart Combination A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

PORTABLE CART WARNING (Symbol provided by RETAC)

3. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
3. Water and Moisture Do not use this product near water—for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

4. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

ANTENNA LEAD IN WIRE

GROUND CLAMP

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

5. Attachments Do not use attachments not recommended by the manufacturer of this product as they may cause hazards.

ELECTRIC SERVICE EQUIPMENT

GROUNDING CONDUCTORS (NEC SECTION 810-21)

6. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

NEC – NATIONAL ELECTRICAL CODE

7. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
Page 5 of the JVC HM-HDS1U user manual — SERVICING
Page 5 · click to enlarge
Page 5

SERVICING

HOW TO USE THIS INSTRUCTION MANUAL

1. Servicing If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
  • All major sections and subsections are listed in the Table Of Contents on page 7. Use this when searching for information on a specific procedure or feature.
  • The Index on pages 90 – 94 lists frequently-used terms, and the number of the page on which they are used or explained in the manual. This section also illustrates the controls and connections on the front and rear panel, the front display panel and the remote control.
  • The mark signals a reference to another page for instructions or related information.
  • Operation buttons necessary for the various procedures are clearly indicated through the use of illustrations at the beginning of each major section.
2. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a.When the power supply cord or plug is damaged. b.If liquid has been spilled, or objects have fallen into the

product. c.If the product has been exposed to rain or water. d.If the product does not operate normally by following the

operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e.If the product has been dropped or damaged in any way. f. When the product exhibits a distinct change in

BEFORE YOU INSTALL YOUR NEW RECORDER . . .

  • . . . please read the sections/literature listed below.
  • ”Cautions” on page 2
  • ”Important Product Safety Instructions” on the previous pages

performance—this indicates a need for service.

3. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
4. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition.
Page 6 of the JVC HM-HDS1U user manual — 3.While using the recorder
Page 6 · click to enlarge
Page 6

PRECAUTION FOR Hard Disk Drive

2.Before using the recorder

1.Before installing the recorder

  • When the power of the unit is on, the hard disc is constantly rotating at high speed. This requires you to note the following:
  • DO NOT impart vibration or shock. If given a heavy shock, not only is the data recorded damaged but also the hard disk itself can be damaged.
  • DO NOT allow anything having strong magnetism or emitting strong electromagnetic waves (cell phones, etc.) near the recorder.
  • DO NOT disconnect the power plug from the wall outlet when the power of the recorder is on. If the power supply is cut off while the hard disc is in operation, it can be damaged or the data stored on it may be damaged. Be sure to push the POWER button before turning off the power.
  • This recorder has a built-in hard disk drive, which is a device to read minute magnetic changes. The inside of the device is precision-built, which, when installing the recorder, requires you to note the following:
  • DO NOT use the recorder in a location prone to vibration or dust.
  • DO NOT place the recorder where difference in temperatures is large (condensation can occur), or where humidity is high. – When condensation occurs

Water droplets form on the hard disc or head drums inside, possibly causing hard disc and heads to be damaged. – About condensation

  • When well-cooled beer is poured into a glass, water droplets often form around its outside. This phenom enon is called condensation.
  • DO NOT install the recorder where the cooling fans in its back may be blocked, or where the recorder may be closed in.
  • DO NOT use the recorder placed vertically.

3.While using the recorder

When viewing a program by selecting HDD (Hard Disk Drive), there occurs a slight time lag relative to the actual program being broadcast. This is because pictures received are once stored on the hard disk, and then played back. The time lag is about three seconds. If you turn the power on with the hard disk already selected, it will take about 30 seconds before the pictures received appear on the screen. Up until then, any operation is disabled. But it is not a malfunction.

Page 8 of the JVC HM-HDS1U user manual — TV
Page 8 · click to enlarge
Page 8

8 EN INSTALLING YOUR NEW RECORDER

Basic Connections

Connections

CHECK CONTENTS 1

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” ( pg. 95).

JVC HM-HDS1U — 8 EN INSTALLING YOUR NEW RECORDER diagram (page 8)
Fig. 2

SITUATE RECORDER 2

Place the recorder on a stable, horizontal surface.

CONNECT RECORDER TO TV 3

The connection method you use depends on the type of TV you have.

a– Disconnect the TV antenna from the TV. b– Connect the TV antenna cable to the ANT. IN jack

on the rear of the recorder. c– Connect the supplied RF cable between the TV

OUT terminal on the rear of the recorder and the TV’s antenna input terminal. d– Connect the supplied Audio/Video Cable between

the AUDIO OUT and VIDEO OUT jacks on the rear of the recorder and the AV IN jacks on the TV. Set your TV in video input mode or A/V input mode. Refer to the TV Instruction Manual. S-VIDEO Connection ●If you have a TV with S-VIDEO input terminals e– Connect the supplied S-Video cable between the S-

VIDEO OUT jack on the rear of the recorder and the S-VIDEO IN jack on the TV.

CONNECT RECORDER TO POWER SOURCE 4

Connect the AC power plug to an AC outlet.

  • The clock and tuner channels will automatically be set when the antenna is connected and when the AC is first connected to the recorder ( pg. 9). (If “Auto” or “CH” is displayed on the front display panel before the recorder is powered on, the clock and tuner channels are being set automatically. Wait for the time to be displayed on the front display panel before powering on the recorder.) FINAL PREPARATION FOR USE 5

TV

Power on the recorder. You can now perform simple playback ( pg. 24 for the HDD deck, pg. 34 for the VHS deck) or simple recording ( pg. 23 for the HDD deck, pg. 35 for the VHS deck).

  • NOTES:
  • For full identification of the recorder’s rear panel, refer to the Index (REAR VIEW pg. 91).
  • TV equipped with Audio and Video Inputs is required to operate the recorder.
  • To make the most of the Super VHS picture performance we recommend that you use the supplied S-VIDEO cable to connect your recorder to a TV with an S-VIDEO input connector.
  • To operate the recorder with your TV using the S-VIDEO connection, set your TV to the AV mode using the TV’s remote control. You can also use the TV/VCR button on the recorder’s remote control to set your TV to the AV mode. ( pg. 82)

Antenna or Cable

Page 9 of the JVC HM-HDS1U user manual — INITIAL SETTINGS
Page 9 · click to enlarge
Page 9

INITIAL SETTINGS

P Aulug to Clock AT If y theTENTION ou use a cable b clock and tunerox, Plug & Play will not function; set channels manually. ( pg.10 – 13) POWER yy HM-HDS1 yyyyEJECT DIGITPURE TECHNOLOGY REC LINK HDD STOP PLAY PAUSE REC S-VHS S-VHS ET VIDEO (M) L – AUDIO – R yyy yyy OK MENU CHNAVI REW A. DUBFEW F - 1 S-VIDEO PAUSE IM ●D P ●If p p cPORTANT on’t press any buttons on the recorder or remote while lug & Play is in progress. you perform Plug & Play successfully, there’s no need to erform the Clock ( pg. 10) and Tuner ( pg. 13) rocedures. If, however, you want to add or delete hannels, refer to “Add Or Delete A Channel” on page 14. D "Auring Initial Auto Clock Set During Auto uto" blinks. The channel as they are scChannel Set Plug & Play Completed numbers are displayed The current time (including anned and set. AM/PM) is displayed. * If an incorrect time or “– –:– –” appears on the display panel, see “What To Do If Plug & Play Has Failed” below. IN ●If c s b “ ●If pFORMATION “AUTO CLOCK” is set to “ON” at the Clock Set screen hannel every hour on the hour (except for 11:00 PM, mid etting data. (This automatic clock adjustment can only be e adjusted on the hour based on the time displayed on th AUTO CLOCK” is “ON”. the memory backup fails, because of a power outage or erformed when power is restored to the recorder.on page 11, the clock will be adjusted automatically by the host night, 1:00 AM and 2:00 AM) by the incoming PBS channel clock performed when the recorder’s power is turned off. The clock will e recorder, not on the actual real time.) The default setting of because the AC was removed from the recorder, Plug & Play will be W ●If a M ●If s t P chat To Do If Plug & Play Has Failed an incorrect time is displayed on the front display panel n adjacent time zone, or an incorrect PBS channel from anual Clock Set ( pg. 12) procedure. Auto channel set “- -:- -” appears on the display, your antenna cable may ignal available in your area. Ensure that the antenna cabl he Plug & Play function will be automatically reactivated lay is not performed but the antenna cable is connected hannel set has not yet taken place, so please also perform, you may be receiving the clock setting data of a PBS channel from a cable TV system. In this case, perform the Semi-Auto ( pg. 11) or has already taken place and it need not be set again. not be connected to the recorder or there may not be a Host PBS e is connected correctly. Then power on and power off the recorder; and “Auto” will be displayed on the recorder’s front panel. If Plug & correctly, perform the Manual Clock Set procedure ( pg. 12). Auto the “Set Receivable Channels” procedure ( pg. 13).
Page 10 of the JVC HM-HDS1U user manual — INITIAL SET
Page 10 · click to enlarge
Page 10

10 EN INITIAL SETTINGS (cont.)

lock urnon the TV and select the AV mode. POWER U EN POWER yyyyyy DIGITPURE TECHNOLOGY EJECT M M-HDS1 REC LINK HDD STOP PLAY PAUSE REC S-VHS S-VHS ET VIDEO (M) L – AUDIO – R yyy MENUNAVI REWFEW

Perform clock setting only if the clock has not been set correctly by the Plug & Play function or you use a cable box. Access the Clock Set screen to perform the Semi-Auto or Manual clock setting procedure. Each procedure starts from step 5. If you use a cable box, set the clock manually. ( pg. 12)

JVC HM-HDS1U — 10 EN INITIAL SETTINGS (cont.) diagram (page 10)
Fig. 3 · 10 EN INITIAL SETTINGS (cont.)

Preparation

TURN ON THE RECORDER 1

Press POWER.

ACCESS MAIN MENU SCREEN 2

Press MENU.

  • If you want to stop the following procedure on its way, press MENU .
HDD/VHS SET UP FUNCTION SET UP TUNER SET INITIAL SET INITIAL SET CLOCK SET GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET INDEX MENU SELECT WITH [∞523] SELECT OK END THEN PRESS [OK]
JVC HM-HDS1U — ACCESS MAIN MENU SCREEN 2 diagram (page 10)
Fig. 4

ACCESS CLOCK SET SCREEN 4

At the Initial Set screen, move the arrow to “CLOCK SET” by pressing %fi (or 5∞), then press # (or 3) or OK.

INITIAL SET

CLOCK SET GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET

  • “CABLE BOX USERS SET CLOCK MANUALLY” appears on the screen for about 5 seconds, then the Clock Set screen appears.

SELECT WITH[5,∞] THEN[OK] PRESS[MENU] TO END

=

Page 11 of the JVC HM-HDS1U user manual — CONTINUED ON NEXT PAGE
Page 11 · click to enlarge
Page 11

Semi-Auto

SELECT TIME ZONE 8

You can change the Host Channel/D.S.T. /Time Zone setting manually.

You can select the time zone automatically or manually. Press # (or 3) or OK repeatedly to move the high- lighted bar to “TIME ZONE”, then press %fi (or 5∞) to select “AUTO” or the desired time zone.

SET AUTO CLOCK TO ON 5

At the Clock Set screen, press # (or 3) or OK repeatedly to move the highlighted bar to “AUTO CLOCK”, then press %fi (or 5∞) to set to “ON”. a– To select the Host

CLOCK SET

TIME DATE YEAR – –:– –AM 1/ 1 01 AUTO CLOCK:ON HOST CH :AUTO (TV) D.S.T. :AUTO TIME ZONE :AUTO SELECT WITH[5,∞] THEN[OK] PRESS[MENU] TO END

AUTO ATLANTIC HAWAII EASTERN ALASKA CENTRAL PACIFIC MOUNTAIN

Channel — go to step 6 b– To select the D.S.T. mode — go to step 7 c– To select the Time Zone — go to step 8

NOTE: If an incorrect time is displayed by the Plug & Play function, you may be receiving the clock setting data of a PBS channel from an adjacent time zone or from an incorrect PBS channel from a cable TV system. If you selected “AUTO” for the host channel in step 6, be sure to select the correct time zone manually. RETURN TO NORMAL SCREEN 9

You can either select “AUTO” or enter a PBS channel number. Press # (or 3) or OK repeatedly to move the high- lighted bar to “HOST CH”, then press %fi (or 5∞) to set to “AUTO” or the desired PBS channel number.

Press MENU. The Initial Set Up screen appears, then press MENU again.

You have three choicesa – Select “AUTO” and the adjustment to your

recorder's clock will be made according to the incoming signal from the host channel. b– Select “ON” and the adjustment will be made based

on the clock itself. c– Select “OFF” if Daylight Saving Time does not apply

to you. Press # (or 3) or OK repeatedly to move the high- lighted bar to “D.S.T.” and press %fi (or 5∞) to select the desired mode.

**AUTO DAYLIGHT SAVING TIME

This function enables automatic adjustment of the recorder’s clock at the start and end of Daylight Saving Time. With Auto DST activated, on the first Sunday of April at 2:00 AM, the clock is

adjusted to 3:00 AM on the last Sunday of October at 2:00 AM, the clock is

adjusted to 1:00 AM.

CONTINUED ON NEXT PAGE

Page 12 of the JVC HM-HDS1U user manual — To Make Corrections
Page 12 · click to enlarge
Page 12

12 EN INITIAL SETTINGS (cont.)

Manual

SET TIME 5

Press %fi (or 5∞) until the desired time appears, then press # (or 3) or OK.

CLOCK SET

TIME DATE YEAR – –:– –AM 1/ 1 01 AUTO CLOCK:ON HOST CH :AUTO (TV) D.S.T. :AUTO TIME ZONE :AUTO SELECT WITH[5,∞] THEN[OK] PRESS[MENU] TO END

  • Press and hold %fi (or 5∞ ) to change the time by 30-minute increments.
  • When the time is entered manually, “AUTO CLOCK” will be automatically set to “OFF”, and “HOST CH” and “TIME ZONE” will disappear.
JVC HM-HDS1U — CLOCK SET diagram (page 12)
Fig. 5

SET DATE 6

Press %fi (or 5∞) until the desired date appears, then press # (or 3) or OK.

  • Press and hold %fi (or 5∞ ) to change the date by 15day increments. SET YEAR 7

Press %fi (or 5∞) until the desired year appears, then press # (or 3) or OK twice.

JVC HM-HDS1U — SET DATE 6 diagram (page 12)
Fig. 6

SELECT D.S.T. MODE 8

Press %fi (or 5∞) to select the desired mode. a– Set to “ON” so that

CLOCK SET

TIME DATE YEAR 9:30AM 6/12 01 TUE AUTO CLOCK:OFF HOST CH :AUTO (TV) D.S.T. :ON TIME ZONE :AUTO SELECT WITH[5,∞] THEN[OK] PRESS[MENU] TO END

the adjustment to your recorder's clock will be made on the clock itself. b– Set to “OFF” if

Daylight Saving Time does not apply to you. START CLOCK 9

Press MENU. The Main Menu screen appears, then press MENU again.

To Make Corrections

Press # (or 3) or OK until the item you want to change blinks, then press %fi (or 5∞).

Page 13 of the JVC HM-HDS1U user manual — PRESS[MENU] TO END
Page 13 · click to enlarge
Page 13

Set Receivable Channels

Tuner

TURN ON THE RECORDER 1

Press POWER.

JVC HM-HDS1U — Set Receivable Channels diagram (page 13)
Fig. 7 · Set Receivable Channels

Turn on the TV and select the AV mode.

ACCESS MAIN MENU SCREEN 2

Press MENU.

ACCESS TUNER SET SCREEN 3

1. At the top of Main Menu screen, move the arrow to “INITIAL SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) At the Initial Set Up screen, move the arrow to “TUNER SET” by pressing @# (or 23 ), then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

TUNER SET INITIAL SET

TUNER SET

BAND AUTO CHANNEL SET MANUAL CHANNEL SET

INDEX MENU

JVC HM-HDS1U — TUNER SET INITIAL SET diagram (page 13)
Fig. 8

PERFORM AUTO CHANNEL SET 4

At the Tuner Set screen, move the arrow to “AUTO CHANNEL SET” by pressing %fi (or 5∞), then press # (or 3) or OK.

TUNER SET

BAND CATV AUTO CHANNEL SET MANUAL CHANNEL SET

  • Receivable channels in your area are automatically assigned to the CH +/– buttons, and non-receivable channels are skipped.
  • If you want to set the CATV channels, change the BAND mode into CATV by moving the arrow to “BAND” and pressing # (or 3 ) or OK . The BAND mode alternates between TV and CATV by pressing # (or 3 ) or OK when BAND is highlighted.

SELECT WITH[5,∞] THEN[OK] PRESS[MENU] TO END

AUTO CHANNEL SET

SCANNING...

PRESS[MENU] TO END

  • NOTES:
  • At the end of Auto Channel Set, “SCAN COMPLETED” appears on screen.
  • If the scan was unsuccessful, “SCAN COMPLETED – NO SIGNAL –” appears on screen. Check the connections and start again. RETURN TO NORMAL SCREEN 5
JVC HM-HDS1U — PRESS[MENU] TO END diagram (page 13)
Fig. 9

INFORMATION The recorder detects the band (TV or CATV) and selects the correct band automatically during Auto Channel Set. The selected band will be displayed on the right side of “BAND” on the Tuner Set screen.

Press MENU. The Initial Set Up screen appears, then press MENU again.

=

Page 14 of the JVC HM-HDS1U user manual — MANUAL CHANNEL SET
Page 14 · click to enlarge
Page 14

14 EN INITIAL SETTINGS (cont.)

Add Or Delete A Channel

ACCESS MAIN MENU SCREEN 1

Press MENU.

ACCESS TUNER SET SCREEN 2

JVC HM-HDS1U — ACCESS TUNER SET SCREEN 2 diagram (page 14)
Fig. 10
1. At the top of Main Menu screen, move the arrow to “INITIAL SET UP” by pressing @# (or 23 ), press fi (or ∞ ) or OK . 2) At the Initial Set Up screen, move the arrow to “TUNER SET” by pressing @# (or 23 ), then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

TUNER SET INITIAL SET

TUNER SET

BAND AUTO CHANNEL SET MANUAL CHANNEL SET

INDEX MENU

ACCESS MANUAL CHANNEL SET SCREEN 3

At the Tuner Set screen, move the arrow to “MANUAL CHANNEL SET” by pressing %fi (or 5∞), then press # (or 3) or OK.

TUNER SET

JVC HM-HDS1U — TUNER SET diagram (page 14)
Fig. 11

BAND TV AUTO CHANNEL SET MANUAL CHANNEL SET

SELECT WITH[5,∞] THEN[OK] PRESS[MENU] TO END

  • If you want to set the CATV channels, change the BAND mode into CATV by moving the arrow to “BAND” and pressing # (or 3 ) or OK . The BAND mode alternates between TV and CATV by pressing # (or 3 ) or OK when BAND is highlighted.

ADD OR SKIP DESIRED CHANNEL 4

Input the channel number using the NUMBER keys or select “L-1” or “F-1” by pressing %fi (or 5∞), then press OK to set to “SKIP”. Repeat for each channel you want to skip. Input the channel number using the NUMBER keys, then press OK to set to “ADD” the channel. RETURN TO NORMAL SCREEN 5

MANUAL CHANNEL SET

(TV) CH 0 SKIP

PRESS NUMBER KEY[0-9] OR[5,∞], THEN[OK] PRESS[MENU] TO END

Press MENU. The Initial Set Up screen appears, then press MENU again.

=

Page 15 of the JVC HM-HDS1U user manual — CABLE
Page 15 · click to enlarge
Page 15

This procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the recorder to automatically switch the cable box channel during timer-recording. The Controller is effective for recording shows that have been programmed using the VCR Plus+ system ( pg. 54) or Express Timer Programming ( pg. 58). Cable Box Control Situate And Connect Controller

Suggested Location Place the cable box on top of the recorder. Attach the recorder’s Controller to the top of the recorder with the Controller’s transmitter pointed towards the cable box’s remote sensor.

SITUATE CONTROLLER 1

Place the Controller so that the path between its transmitter and the cable box’s remote sensor is unobstructed. ATTACH CONTROLLER 2

Fasten securely using the supplied adhesive strip.

CONNECT CABLE BOX TO RECORDER 3

The connection method depends on the type of cable box you have.

If your cable box has AUDIO and VIDEO OUT connectors . . .. . . connect them to the AUDIO and VIDEO IN connectors on your recorder. Set the recorder to channel “L-1” for the rear AUDIO and VIDEO IN connectors to use the cable box. If your cable box doesn’t have AUDIO and VIDEO OUT connectors . . .. . . connect the antenna output connector on the cable box to the ANTENNA IN connector on the rear of your recorder. Set the recorder tuner to the same channel as the cable box RF output (see page 16 also). NOTE: When connecting your cable box refer to its instruction manual. CONNECT CONTROLLER TO RECORDER 4

Connected to ANT. IN

Connect to the CABLE BOX connector on your recorder.

  • About Your Cable Box This recorder has two separate methods to control your Cable Box.
  • The recorder’s Wireless Remote Control Unit can control your Cable Box. This eliminates the need for a separate Cable Box Remote Control Unit.
  • The recorder’s Controller can also control your Cable Box. This allows the recorder to change your Cable Box's channel number during timer recording. Each method must be set up separately. To set up the recorder’s Remote Control unit, refer to page 83. To set up the Controller go to page 16.

CABLE

BOX

CONTINUED ON NEXT PAGE

Show 7 more labels / short text on this page
Cable box · Controller (suggested locations) · Your recorder · Cable box · Controller · Transmitter · Your recorder
Page 16 of the JVC HM-HDS1U user manual — CABLE BOX SET
Page 16 · click to enlarge
Page 16

INITIAL SETTINGS (cont.)

Set Cable Box Output Channel & Cable Box Brand

Turn on the TV and select the AV mode.

TURN ON CABLE BOX 1

Select a channel other than channel 9 on your cable box.

JVC HM-HDS1U — TURN ON CABLE BOX 1 diagram (page 16)
Fig. 12

TURN ON THE RECORDER 2

Press POWER.

ACCESS MAIN MENU SCREEN 3

Press MENU.

ACCESS INITIAL SET SCREEN 4

1. At the top of Main Menu screen, move the arrow to “INITIAL SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) At the Initial Set Up screen, move the arrow to “INITIAL SET” by pressing @# (or 23 ), then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

TUNER SET INITIAL SET

INITIAL SET

CLOCK SET GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET

JVC HM-HDS1U — TUNER SET INITIAL SET diagram (page 16)
Fig. 13

INDEX MENU

ACCESS CABLE BOX SET SCREEN 5

Press %fi (or 5∞) to move the arrow to “CABLE BOX SET”, then press # (or 3) or OK.

INITIAL SET

CLOCK SET GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET

SELECT WITH[5,∞] THEN[OK] PRESS[MENU] TO END

SELECT CABLE BOX OUTPUT CHANNEL 6

If your cable box is connected to your recorder using an RF connection, press %fi (or 5∞) until the channel number representing the cable box’s output (CH2 – CH9) appears on the screen.

CABLE BOX SET

ON CH7

PRESS[5,∞], THEN[OK] PRESS[MENU] TO END

If your cable box is connected to your recorder’s REAR or FRONT AUDIO/VIDEO IN connectors, press %fi (or 5∞) until “ON L-1 REAR” or “ON F-1 FRONT” appears on the screen.

=

Page 17 of the JVC HM-HDS1U user manual — CABLE BOX BRAND LIST
Page 17 · click to enlarge
Page 17

ACCESS CABLE BOX BRAND SET SCREEN 7

INFORMATION

When the recorder’s clock has not been set (with AUTO CLOCK set to ON), if you press OK in step 7, “CABLE BOX USERS SET CLOCK MANUALLY” will be displayed on the screen for about 5 seconds, then the Clock Set screen will appear; perform the manual clock setting procedure on page 12. If you press MENU after the clock has been set, the Cable Box Brand Set screen appears.

Press # (or 3) or OK.

ENTER CABLE BOX BRAND 8

Press the appropriate NUMBER keys to enter the Cable Box Code from the CABLE BOX BRAND LIST shown below, then press # (or 3) or OK.

CABLE BOX BRAND SET

  • NOTES:
  • Although the supplied Controller is compatible with many different cable box brands, it is possible that it will not work with your cable box.
  • If your cable box doesn’t respond to any code between 1 and 25, you can’t use the Controller to change cable box channels. In this case, make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start of timer recording. Please contact your cable company about the possibility of exchanging your current cable box with one that is compatible with your recorder.
  • The recorder can only change the cable box channel through the Controller during timer recording.
  • If your cable box is one that can’t be operated with a remote control (because it has no remote sensor), you can’t use the Controller to change its channels. Make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start of timer recording.
  • If the recorder’s memory backup expires because of a power failure, set the cable box output channel and brand again.
  • If you are unable to set the Controller, please contact JVC toll free at 1-800-252-5722.

PRESS NUMBER KEY(0-9) THEN(OK) TO TEST PRESS(MENU) TO END

  • If the cable box’s channel changes to 9, setting is complete. Press # (or 3 ) or OK and “CABLE BOX CONTROL IS ON” appears on the screen for about 5 seconds, then the Initial Set Up screen appears. To returns to the normal screen, press MENU .
  • If the cable box’s channel does not change to 9, press %fi (or 5∞ ) to select “NO”, then press # (or 3 ) or OK . By entering another code, repeat step 8 until the cable box’s channel changes to 9.
  • If the channel does not change after going through all the code numbers listed for your model of cable box, then try all the other numbers between 1 and 25.

CABLE BOX BRAND LIST

BRAND CODE

ARCHER 1, 5, 17 CABLETENNA 1, 17 CABLEVIEW 15, 16, 17, 21, 25 CITIZEN 15, 16, 17, 21, 25 CURTIS 2, 8 DIAMOND 1, 17 EASTERN 19 GC BRAND 15, 16, 17, 21, 25 GEMINI 15 GENERAL INSTRUMENTS 1, 4, 6, 11, 12, 15 HAMLIN 10, 18, 19, 23 JASCO 15 JERROLD 1, 4, 6, 11, 12, 15 NOVAVISION 2, 8 OAK 7, 20 PANASONIC 13, 14 PULSER 15, 16, 17, 21, 25 RCA 13, 14 REGAL 10, 18, 19, 23 REGENCY 19 REMBRANDT 1, 16, 17 SAMSUNG 5, 16, 24 SCIENTIFIC ATLANTA 2, 8 SIGMA 7, 20 SL MARX 5, 16, 17, 24, 25 SPRUCER 13, 14 STARGATE 5, 15, 16, 17, 21, 24, 25 TELEVIEW 5, 16, 24 TOCOM 1, 4, 16 UNIKA 1, 17 UNIVERSAL 16, 17, 25 VIDEOWAY 3, 9, 22 ZENITH 3, 9, 22

Page 18 of the JVC HM-HDS1U user manual — CABLE
Page 18 · click to enlarge
Page 18

INITIAL SETTINGS (cont.)

  • The following procedure is required if you receive satellite channels through a DBS (Direct Broadcast Satellite) Receiver. The Controller allows the recorder to automatically switch the DBS Receiver's channels during timer recording. NOTES:
  • The recorder can automatically change the DBS Receiver channels using the controller when the recorder has been programmed using Express Timer Programming ( pg. 58). Because satellite programming does not use PlusCode; the Controller cannot change the DBS Receiver channels during the VCR Plus+ Timer Recording.
  • If a cable box is also used it is recommended that you connect the DBS receiver to your recorder’s A/V inputs and the cable box to your recorder’s antenna input.

DBS Receiver Control

Suggested Location Place the DBS (Direct Broadcast Satellite) receiver on top of the recorder. Attach the recorder’s Controller to the top of the recorder with the Controller’s transmitter pointed towards the DBS receiver's remote sensor. ATTENTION: The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the controller so its signal reaches the remote control sensors of both the DBS receiver and cable box.

Situate And Connect Controller

SITUATE CONTROLLER 1

Place the Controller so that the path between its transmitter and the DBS receiver's remote sensor is unobstructed. ATTACH CONTROLLER 2

Fasten securely using the supplied adhesive strips.

Controller (suggested locations) Your recorder

CONNECT DBS RECEIVER TO RECORDER 3

The connection method depends on the type of DBS receiver you have.

If your DBS receiver has AUDIO and VIDEO OUT connectors . . .. . . connect them to the AUDIO and VIDEO IN connectors on your recorder. Set the recorder to channel “L-1” for the rear AUDIO and VIDEO IN connectors to use the DBS receiver. If your DBS receiver doesn’t have AUDIO and VIDEO OUT connectors . . .. . . connect the antenna output connector on the DBS receiver to the ANT. IN connector on the rear of your recorder. Set the recorder’s tuner to the same channel as the DBS receiver’s RF output. (See page 19 also.) NOTE: When connecting your DBS receiver refer to its instruction manual. CONNECT CONTROLLER TO RECORDER 4

Connected to VIDEO/ AUDIO IN

Connected to ANT. IN

CABLE

BOX

About Your DBS Receiver This recorder has two separate methods to control your DBS Receiver.

Connect to the CABLE BOX connector on your recorder.

  • The recorder’s Wireless Remote Control Unit can control the power and channel functions of your DBS Receiver. For these functions, the need for a separate DBS Receiver Control Unit is eliminated.
  • The recorder’s Controller can also control your DBS Receiver. This allows the recorder to change your DBS receiver's channel number during timer recording.

Each method must be set up separately. To set up the recorder’s Remote Control unit, refer to page 84. To set up the Controller go to page 19.

Show 5 more labels / short text on this page
DBS receiver · DBS receiver · Controller · Transmitter · Your recorder
Page 19 of the JVC HM-HDS1U user manual — CONTINUED ON NEXT PAGE
Page 19 · click to enlarge
Page 19

TURN ON THE RECORDER 2

Turn on the TV and select the AV mode.

Press POWER.

JVC HM-HDS1U — TURN ON THE RECORDER 2 diagram (page 19)
Fig. 14
  • Set the recorder to the channel (3 or 4 or L-1 or F-1) on which the signals from the DBS receiver are received. ACCESS MAIN MENU SCREEN 3

Press MENU.

ACCESS INITIAL SET SCREEN 4

1. At the top of Main Menu screen, move the arrow to “INITIAL SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) At the Initial Set Up screen, move the arrow to “INITIAL SET” by pressing @# (or 23 ), then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

TUNER SET INITIAL SET

INITIAL SET

CLOCK SET GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET

JVC HM-HDS1U — TUNER SET INITIAL SET diagram (page 19)
Fig. 15

INDEX MENU

ACCESS DBS RECEIVER SET SCREEN 5

At the Initial Set screen, move the arrow to “DBS RECEIVER SET” by pressing %fi (or 5∞), then press # (or 3) or OK.

INITIAL SET

CLOCK SET GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET

SELECT WITH[5,∞] THEN[OK] PRESS[MENU] TO END

SELECT DBS RECEIVER OUTPUT CHANNEL 6

If your DBS receiver is connected to your recorder using an RF connection, press %fi (or 5∞) until the channel number representing the DBS receiver’s output (CH3 – CH4) appears on the screen.

DBS RECEIVER SET

OFF

PRESS[5,∞], THEN[OK] PRESS[MENU] TO END

If your DBS receiver is connected to your recorder’s REAR or FRONT AUDIO/VIDEO IN connectors, press %fi (or 5∞) until “ON L-1 REAR” or “ON F-1 FRONT” appears on the screen.

Set DBS Receiver Output Channel & DBS Receiver Brand

JVC HM-HDS1U — Set DBS Receiver Output Channel & DBS Receiver Brand diagram (page 19)
Fig. 16 · Set DBS Receiver Output Channel & DBS Receiver Brand

Select a channel other than channel 55, 100 or 205 on your DBS receiver.

CONTINUED ON NEXT PAGE

=

Page 20 of the JVC HM-HDS1U user manual — DBS RECEIVER BRAND SET
Page 20 · click to enlarge
Page 20

INITIAL SETTINGS (cont.)

ACCESS DBS RECEIVER BRAND SET SCREEN 7

Turn on the TV and select the AV mode.

Press # (or 3) or OK.

SET DBS RECEIVER BRAND 8

Press the appropriate NUMBER keys to enter the DBS Receiver Code from the following list, then press # (or 3) or OK.

DBS RECEIVER BRAND SET

JVC HM-HDS1U — DBS RECEIVER BRAND SET diagram (page 20)
Fig. 17

PRESS NUMBER KEY(0-9) THEN(OK) TO TEST PRESS(MENU) TO END

BRAND CODE JVC (DISH Network) 51 ECHOSTAR (DISH Network) 51 PRIMESTAR 50 SONY (DSS) 41 RCA (DSS) 40

  • After OK is pressed, the program currently received through the DBS receiver will appear for about 10 seconds.
  • If the DBS receiver's channel changes to the channel listed below for your brand of DBS receiver, setting is complete. Press OK and “DBS RECEIVER CONTROL IS ON” appears on the screen for about 5 seconds, then it returns to the Initial Set Up screen. To returns to the normal screen, press MENU .
JVC HM-HDS1U — DBS RECEIVER BRAND SET diagram (page 20)
Fig. 18

JVC [ 100 ECHOSTAR [ 100 PRIMESTAR [ 55 SONY [ 205 RCA [ 205 ●If the DBS receiver's channel does not change as shown above, press %fi (or 5∞) repeatedly until “NO” appears, then press OK. Re-enter the correct code.

  • NOTES:
  • It is possible that the Controller will not work with all types of DBS receiver.
  • If your DBS receiver doesn’t respond to the code, you can’t use the Controller to change satellite channels. In this case, make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start of timer recording.
  • The recorder can only change the satellite channel through the Controller during timer recording.
  • If your DBS receiver is one that can’t be operated with a remote control (because it has no remote sensor), you can’t use the Controller to change its channels. Make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start of timer recording.
  • If you are unable to set the Controller, please contact JVC toll free at 1-800-252-5722.
Page 21 of the JVC HM-HDS1U user manual — RETURN TO NORMAL SCREEN 5
Page 21 · click to enlarge
Page 21

The recorder changes the screen into the Blue Back screen automatically after/while the input signals do not come into.

Setting Blue Back

TURN ON THE RECORDER 1

Press POWER.

ACCESS MAIN MENU SCREEN 2

Turn on the TV and select the AV mode.

Press MENU.

JVC HM-HDS1U — ACCESS MAIN MENU SCREEN 2 diagram (page 21)
Fig. 19
  • If you want to stop the following procedure on its way, press MENU .

ACCESS FUNCTION SCREEN 3

1. At the top of Main Menu screen, move the arrow to “FUNCTION SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) On the Function Set Up screen, move the arrow to “FUNCTION” by pressing @# (or 23 ), then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VIDEO INPUTS FUNCTION

SUPERIMPOSE OFF

BLUE BACK ON

2ND AUDIO RECORD OFF

INDEX MENU

JVC HM-HDS1U — VIDEO INPUTS FUNCTION diagram (page 21)
Fig. 20

SELECT BLUE BACK MODE 4

1. On the Function screen, move the arrow to “BLUE BACK” by pressing %fi (or 5∞ ), then press OK . 2) Press %fi (or 5∞ ) to select the desired mode, then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VIDEO INPUTS FUNCTION

SUPERIMPOSE OFF

BLUE BACK ON

OFF ON

2ND AUDIO RECORD OFF

INDEX MENU

a– Select “OFF” if you do not want to use the Blue

Back screen. b– Select “ON” if you want to use the Blue Back

screen.

RETURN TO NORMAL SCREEN 5

Press MENU.

Page 22 of the JVC HM-HDS1U user manual — RETURN TO NORMAL SCREEN 5
Page 22 · click to enlarge
Page 22

INITIAL SETTINGS (cont.)

You can change the video inputs mode.

Setting Video Inputs Mode

TURN ON THE RECORDER 1

Press POWER.

ACCESS MAIN MENU SCREEN 2

Turn on the TV and select the AV mode.

Press MENU.

JVC HM-HDS1U — ACCESS MAIN MENU SCREEN 2 diagram (page 22)
Fig. 21
  • If you want to stop the following procedure on its way, press MENU .

ACCESS VIDEO INPUTS SCREEN 3

1. At the top of Main Menu screen, move the arrow to “FUNCTION SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) On the Function Set Up screen, move the arrow to “VIDEO INPUTS” by pressing @# (or 23 ), then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VIDEO INPUTS FUNCTION

SUPERIMPOSE OFF

BLUE BACK ON

2ND AUDIO RECORD OFF

INDEX MENU

JVC HM-HDS1U — VIDEO INPUTS FUNCTION diagram (page 22)
Fig. 22

SELECT VIDEO INPUTS MODE 4

1. On the Function screen, move the arrow to “FRONT AUX F-1” or “REAR AUX L-1” by pressing %fi (or 5∞ ), then press OK . 2) Press %fi (or 5∞ ) to select the desired mode, then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VIDEO INPUTS FUNCTION

FRONT AUX F-1 VIDEO

VIDEO S-VIDEO

REAR AUX L-1 VIDEO

INDEX MENU

a– Select “VIDEO” if you use VIDEO IN jacks for

connecting the external equipment. b– Select “S-VIDEO” if you use S VIDEO IN jacks for

connecting the external equipment.

RETURN TO NORMAL SCREEN 5

Press MENU.

Page 23 of the JVC HM-HDS1U user manual — STOP RECORDING 6
Page 23 · click to enlarge
Page 23

SIMPLE OPERATION for HDD deck

TURN ON THE RECORDER 1

Simple Recording

Press POWER. The button corresponding to the previously selected deck lights.

SELECT HDD DECK 2

Press HDD. The HDD button lights on the front panel.

JVC HM-HDS1U — SELECT HDD DECK 2 diagram (page 23)
Fig. 23

Turn on the TV and select the AV mode.

SELECT RECORDING CHANNEL 3

If the recorder is turned on with HDD deck selected, there may be about 30 seconds' delay in starting to show pictures on the screen.

Press CH +/–. Or press the appropriate NUMBER keys, then press ENTER. (The channel changes after a few seconds whether you press ENTER or not.)

JVC HM-HDS1U — SELECT RECORDING CHANNEL 3 diagram (page 23)
Fig. 24

When you switch channels on the HDD deck, the pictures appears a few seconds behind. It is not a malfunction.

SET RECORDING SPEED 4

Press REC SPEED to set the recording speed.

  • For details on the recording speed, see the next page. START RECORDING 5

Press and hold REC and press PLAY on the remote control, or press REC on the front panel. The HDD recording indicator lights.

STOP RECORDING 6

JVC HM-HDS1U — STOP RECORDING 6 diagram (page 23)
Fig. 25

Press STOP. The HDD recording indicator turns off.

There may be a few seconds’ delay in resuming normal screen. It is not a malfunction.

  • NOTES:
  • It is not possible to record a TV program on both the HDD deck and the VHS deck simultaneously. In addition, it is not possible to record simultaneously from the same external input.
  • It is not possible to pause recording on the HDD deck while recording from the channels other than “L-1”, “F-1”, “DUB”. See also pages 73 and 77.
Page 24 of the JVC HM-HDS1U user manual — STOP PLAYBACK 5
Page 24 · click to enlarge
Page 24

SIMPLE OPERATION for HDD deck (cont.)

TURN ON THE RECORDER 1

Simple Playback

Press POWER. The button corresponding to the previously selected deck lights on the front panel.

SELECT HDD DECK 2

Press HDD. The HDD button lights on the front panel.

JVC HM-HDS1U — SELECT HDD DECK 2 diagram (page 24)
Fig. 26

Turn on the TV and select the AV mode.

START PLAYBACK 3

If the recorder is turned on with HDD deck selected, there may be about 30 seconds' delay in starting to show pictures on the screen.

Press PLAY. The HDD playback indicator lights on the front panel. One of the following screens will appear: – the program which has been recorded on the HDD

JVC HM-HDS1U — START PLAYBACK 3 diagram (page 24)
Fig. 27

deck at the last and has not been played back yet – the program which has been stopped during playback – the HDD Navigation screen (See the next page.)

  • There are some programs for demonstration on the HDD deck when it is shipped from the factory.

PAUSE PLAYBACK 4

Press PAUSE.

  • To resume normal playback, press PLAY .

STOP PLAYBACK 5

Press STOP. The HDD playback indicator turns off.

JVC HM-HDS1U — STOP PLAYBACK 5 diagram (page 24)
Fig. 28

Recording Speed on the HDD deck This recorder has a 40 Gbyte hard disk drive. The pictures and sounds recorded on the HDD deck and other information are written down on the hard disk drive. As recording format for the HDD deck, MPEG2 format, the same for DVD, is used. As a guide for picture quality, the “bps” unit is used to represent how much data can be recorded per second. The larger this value, the better the picture quality is but the more capacity is required for recording. Select SP for programs where quick movement occurs, such as sports programs, and SEP for talk shows, etc. where relativity less movement. The recording speeds of the recorder are set as follows:

JVC HM-HDS1U — STOP PLAYBACK 5 diagram (page 24)
Fig. 29
Page 25 of the JVC HM-HDS1U user manual — INDEX NAVI
Page 25 · click to enlarge
Page 25

The HDD Navigation enables you to seach and select the desired programs recorded on the HDD deck very easily. There is a 40 Gbyte hard disk drive on this recorder. You can record up to 60 programs for the HDD deck. Each time a program is recorded on the HDD deck, the information of the program are registered in the HDD Navigation automatically. So, you can confirm the information of the programs recorded on the HDD with the HDD Navigation Screen. And, you can also select one of the programs recorded on the HDD deck using the HDD Navigation.

Playback with HDD Navigation

The following screen appears as the HDD Navigation screen when you press NAVI with the HDD deck selected. You can move the arrow to select the desired position on the screen by pressing @%#fi (or 253∞). When you move the arrow at the top of the HDD Navigation screen, you can change the screens by pressing @# (or 23).

You need to select “SCAN” to scan the beginning of the programs.

REMAIN TIME : it is based on the recording speed currently selected.

HDD NAVI

There are 6 recorded programs and the program indicated by the arrow is the 3rd one.

TOTAL TIMEfor the selected programs

SCAN EDITING EASY DUBBING

TOTAL TIME 0H00M REMAIN TIME 11H07M (SP)

Indexsmall still picture of the each program

D W

This appears when there are over 4 registered programs. You can select the other program by pressing @# (or 23).

Recording Informa- tion for the program indicated by the arrow

06/12/01 TUE 06/11/01 MON 06/11/01 MON 06/12/01 TUE

[MISC.]

06/12/01 TUE 10:30AM – 12:55PM 2CH SP 145min

ST

PLAY MODIFY DELETE CANCEL

The icons : they show the recording situation for each program.

INDEX NAVI

The Icons and their meanings

You cannot dub this program from the HDD deck to the VHS deck.

D This program was recorded with Daily mode of Timer recording.

W This program was recorded with Weekly mode of Timer recording.

ST This program has stereo sounds.

SA This program has SAP audio.

This program was recorded with Timer recording.

3 / 6 · Operational commands · Guidance for operations

Page 26 of the JVC HM-HDS1U user manual — STOP PLAYBACK 7
Page 26 · click to enlarge
Page 26

26 EN SIMPLE OPERATION for HDD deck (cont.)

JVC HM-HDS1U — 26 EN SIMPLE OPERATION for HDD deck (cont.) diagram (page 26)
Fig. 30 · 26 EN SIMPLE OPERATION for HDD deck (cont.)

Turn on the TV and select the AV mode. Scan for Beginning(s) of Program(s) You can scan the beginning of the program easily with the HDD Navigation.

If the recorder is turned on with HDD deck selected, there may be about 30 seconds' delay in starting to show pictures on the screen.

TURN ON THE RECORDER 1

Press POWER.

SELECT HDD DECK 2

JVC HM-HDS1U — SELECT HDD DECK 2 diagram (page 26)
Fig. 31

Press HDD. The HDD button lights.

ACCESS SCAN SCREEN 3

1. Press NAVI . The HDD Navigation screen appears. 2) Confirm that “SCAN” screen appears. Then, press fi (or ∞ ) or OK .

HDD NAVI

SCAN EDITING EASY DUBBING

TOTAL TIME 0H00M REMAIN TIME 11H07M (SP)

06/12/01 TUE 06/12/01 TUE 06/12/01 MON 06/12/01 TUE

06/12/01 TUE 10:30AM – 12:55PM 2CH SP 145min

[MISC.]

PLAY MODIFY DELETE CANCEL

INDEX

SELECT PROGRAM(S) 4

Press @# (or 23) to move the arrow on the index (small still pictures) of the desired program.

JVC HM-HDS1U — [MISC.] diagram (page 26)
Fig. 32

HDD NAVI

SCAN EDITING EASY DUBBING

TOTAL TIME 0H00M REMAIN TIME 11H07M (SP)

06/12/01 TUE 06/12/01 TUE 06/12/01 MON 06/12/01 TUE

[MISC.]

  • When you want the plural programs to be played back continuously, press MEMORY on the remote control after selecting the desired program. The numbers of the playback order appear on the index. You can select up to 8 programs.
  • When you want to correct the order, move the arrow on the desired index and press MEMORY on the remote control. Or, move the arrow on the desired index and press OK , then move the arrow to “CANCEL” and press OK . The number disappears and the recorder re-numbers the other programs automatically.

06/12/01 TUE 10:30AM – 12:55PM 2CH SP 145min

PLAY MODIFY DELETE CANCEL

INDEX

START PLAYBACK 5

Press OK to move the arrow to “PLAY” on the Scan Screen, then press OK again. Or simply press PLAY. The playback starts.

PAUSE PLAYBACK 6

Press PAUSE.

  • To resume normal playback, press PLAY .

STOP PLAYBACK 7

Press STOP.

– / 6 · – / 6

Page 27 of the JVC HM-HDS1U user manual — Start Live Memory Playback
Page 27 · click to enlarge
Page 27

PLAYBACK FEATURES for HDD deck

Setting Time for Live Memory Playback

Live Memory Playback

ACCESS MAIN MENU SCREEN 1

Press MENU.

Equipped with a hard disk drive, this recorder allows informa- tion to be written to and read from the hard disk at high speeds. Taking advantage of this feature, you can temporarily record programs received with the tuner or from an externally- connected equipment — CATV or DBS, and can watch them only a few seconds behind actual air time. In this recorder, viewing a program through HDD (not a recorded program) means you are always watching the program temporarily recorded on it. This feature enables you to reverse the program back to view any previous part of it — so called “Live Memory Playback”, which was impossible until now. To access “Live Memory Playback”, all that you have to do is to turn on the recorder and select the HDD deck. So, the temporary recording is started on the HDD deck. And, you can select the length of the time for temporary recording from off, 30 minutes, 1 hour, and 3 hours.

  • If you want to stop the following procedure on its way, press MENU .

ACCESS HDD SET UP SCREEN 2

1. Press @# (or 23 ) to move the arrow to “HDD/VHS SET UP”, then press fi (or ∞ ) or OK . 2) Press @# (or 23 ) to move the arrow to “HDD SET UP”, then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

LIVE MEMORY 1 HR.

INDEX MENU

SELECT LIVE MEMORY MODE 3

About “Live Memory Playback” With a certain amount of space (for 30 minutes, 1 hour, and 3 hours) reserved on the hard disk, the recorder records broad- casts being received or signals input from an externally connected equipment. Even while you are reversing the program to review any previous part, the recorder continues recording the same program or externally-input signals. When the reserved amount of time (or space) runs out, the recorder overwrites the previous recordings on the hard disk, starting with the oldest one, repeatedly if necessary. After having recorded a certain number of programs, if you try to increase the amount of your reserved time on HDD, you may not be allowed to do so because of possible lack of available space, and the recorder will inform you of this by displaying a message on the screen.

1. At the “LIVE MEMORY”, press OK . 2) Press %fi (or 5∞ ) to select the desired mode, then press OK . a – Select “OFF” if you

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

LIVE MEMORY 1 HR.

OFF 30 MIN. 1 HR. 3 HR.

do not want to use the Live Memory Playback. b– Select “30 MIN.” if you want to use the Live

INDEX MENU

Memory Playback for up to 30 minutes. c– Select “1 HR.” if you want to use the Live Memory

Playback for up to an hour. d– Select “3 HR.” if you want to use the Live Memory

About limitation on Live Memory Playback Recording to perform Live Memory playback, which means the use of temporary recording on the hard disk, works for signals from built-in tuners, external tuners and externally- connected equipment. This feature also works for copy- protected programs. The temporary recording for Live Memory is canceled in the following cases, and will start all over again when it is to resume.

Playback for up to 3 hours.

RETURN TO NORMAL SCREEN 4

Press MENU.

  • When channels are changed
  • When the power is turned off
  • When the thumbnails are changed
  • When the setting for Live Memory playback is changed
  • When recording is started via the HDD deck or the VHS deck
  • When a recorded program is played back or deleted

Start Live Memory Playback

You can start Live Memory Playback by pressing @ (or 2) or 1, then press PLAY. When you press @ (or 2) to start Live Memory Playback, the recorder will rewind the pictures to the point where Live Memory time counter shows “00” or “30” in its minutes’ place (or to the beginning of the program), then start Live Memory Playback automatically. You can use various playback features during Live Memory Playback. (See pages 30 and 31.)

  • To stop Live Memory Playback, press STOP . The on-air screen resumes.
Page 28 of the JVC HM-HDS1U user manual — RETURN TO NORMAL SCREEN 4
Page 28 · click to enlarge
Page 28

PLAYBACK FEATURES for HDD deck (cont.)

JVC HM-HDS1U — PLAYBACK FEATURES for HDD deck (cont.) diagram (page 28)
Fig. 33 · PLAYBACK FEATURES for HDD deck (cont.)

Superimpose

Turn on the TV and select the AV mode.

This function, switchable between ON and OFF, determines whether or not operational indicators will appear on screen.

If the recorder is turned on with HDD deck selected, there may be about 30 seconds' delay in starting to show pictures on the screen.

ACCESS MAIN MENU SCREEN 1

Press MENU.

  • If you want to stop the following procedure on its way, press MENU.
JVC HM-HDS1U — ACCESS MAIN MENU SCREEN 1 diagram (page 28)
Fig. 34

ACCESS FUNCTION SCREEN 2

1. At the top of Main Menu screen, move the arrow to “FUNCTION SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) On the Function Set Up screen, move the arrow to “FUNCTION” by pressing @# (or 23 ), then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VIDEO INPUTS FUNCTION

SUPERIMPOSE OFF

BLUE BACK ON

2ND AUDIO RECORD OFF

INDEX MENU

JVC HM-HDS1U — VIDEO INPUTS FUNCTION diagram (page 28)
Fig. 35

SELECT SUPERIMPOSE MODE 3

1. On the Function screen, move the arrow to “SUPERIMPOSE” by pressing %fi (or 5∞ ), then press OK . 2) Press %fi (or 5∞ ) to select the desired mode, then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VIDEO INPUTS FUNCTION

SUPERIMPOSE OFF

BLUE BACK ON

OFF ON

2ND AUDIO RECORD OFF

INDEX MENU

a– Select “ON” if you want the superimposed opera-

tional indications on the screen for about 5 seconds when operating the recorder. b– Select “OFF” if you do not want the superimposed

operational indications on the screen.

RETURN TO NORMAL SCREEN 4

Press MENU.

Page 29 of the JVC HM-HDS1U user manual — STEREO 8:00 PM 9:00 PM 10:00 PM 1CH
Page 29 · click to enlarge
Page 29

To Recall Indication

Press OSD. The indication appears on the top of the screen as follows.

ON AIR PRESENT TIME 9:47 PM LP

1CH STEREO 8:00 PM 9:00 PM 10:00 PM

To clear the indication, press OSD again.

When playing back a recorded program

Playback mode and time counter

Recording informationdate, start time, channel and recording speed

The beginning of the program

PLAY 3 0:59:24

06/12 TUE 10:07 AM LP

STEREO 0:00 1:00 2:00

Time scale Time scale of the current program : This program has an hour and a half contents.

The end of the program

When watching a program on air

ON AIR PRESENT TIME ∞ 9:32:15 PM LP

Time scale around the current time

STEREO 8:00 PM 9:00 PM 10:00 PM

The beginning point of this program : The recorder starts receiving this program at about 8:30 PM.

Pointer for current time : The recorder has been receiving this program for an hour.

You can enjoy Live Memory Playback in this field.

When pressing PAUSE

PAUSE is pressed at 9:33 PM.

PRESENT TIME ∞ 9:45 PM PAUSE 8 9:33 PM

LP

STEREO 8:00 PM 9:00 PM 10:00 PM 1CH

Pointer for current picture The end of this program : The recorder is now capturing new pictures in this point.

When using Live Memory playback

The time counter using actual time

PRESENT TIME ∞ 9:46 PM LIVE MEMORY 3 9:03 PM LP

STEREO 8:00 PM 9:00 PM 10:00 PM 1CH

Pointer for current picture The end of this program : The recorder is now capturing new pictures in this point.

Show 5 more labels / short text on this page
Audio mode · Current playback point · Current time · Current recording speed · Current channel
Page 30 of the JVC HM-HDS1U user manual — Slow Motion/Reverse Slow Motion
Page 30 · click to enlarge
Page 30

PLAYBACK FEATURES for HDD deck (cont.)

High-Speed Search

Playback Features

JVC HM-HDS1U — PLAYBACK FEATURES for HDD deck (cont.) diagram (page 30)
Fig. 36 · PLAYBACK FEATURES for HDD deck (cont.)

During playback (or Live Memory Playback), press FF for forward high-speed search, or REW for reverse high- speed search.

  • The search speed is 15 times normal playback speed.
JVC HM-HDS1U — PLAYBACK FEATURES for HDD deck (cont.) diagram (page 30)
Fig. 37 · PLAYBACK FEATURES for HDD deck (cont.)

Turn on the TV and select the AV mode.

To resume normal playback, press PLAY.

If the recorder is turned on with HDD deck selected, there may be about 30 seconds' delay in starting to show pictures on the screen.

  • NOTES:
  • For short searches, during playback or still, press and hold FF, or REW . When released, normal playback resumes.
  • If either end of the program is reached during high-speed search, normal playback will resume.

Still Picture/Frame-By-Frame Playback

JVC HM-HDS1U — Still Picture/Frame-By-Frame Playback diagram (page 30)
Fig. 38 · Still Picture/Frame-By-Frame Playback
JVC HM-HDS1U — Still Picture/Frame-By-Frame Playback diagram (page 30)
Fig. 39 · Still Picture/Frame-By-Frame Playback

Press PAUSE or # (or 3) repeatedly to advance one frame at a time. Press @ (or 2) repeatedly to reverse one frame at a time.

JVC HM-HDS1U — Still Picture/Frame-By-Frame Playback diagram (page 30)
Fig. 40 · Still Picture/Frame-By-Frame Playback

To resume normal playback, press PLAY.

Slow Motion/Reverse Slow Motion

JVC HM-HDS1U — Slow Motion/Reverse Slow Motion diagram (page 30)
Fig. 41 · Slow Motion/Reverse Slow Motion

For hands-free slow-motion, press PAUSE during playback (or Live Memory Playback).

Press and hold # (or 3) for forward slow-motion, @ (or 2) for reverse slow-motion.

Press # (or 3) or @ (or 2) repeatedly. The slow-motion speed changes in three steps for each direction.

To resume normal playback, press PLAY.

Page 31 of the JVC HM-HDS1U user manual — Quick Skip Forward
Page 31 · click to enlarge
Page 31
JVC HM-HDS1U — PLAYBACK FEATURES for HDD deck diagram (page 31)
Fig. 42 · PLAYBACK FEATURES for HDD deck

Variable-Speed Search/ Reverse Motion Playback

Turn on the TV and select the AV mode.

If the recorder is turned on with HDD deck selected, there may be about 30 seconds' delay in starting to show pictures on the screen.

JVC HM-HDS1U — Variable-Speed Search/ Reverse Motion Playback diagram (page 31)
Fig. 43 · Variable-Speed Search/ Reverse Motion Playback

During playback (or time-shift playback), press # (or 3) for forward variable-speed search or press @ (or 2) for reverse motion playback.

JVC HM-HDS1U — Variable-Speed Search/ Reverse Motion Playback diagram (page 31)
Fig. 44 · Variable-Speed Search/ Reverse Motion Playback

Press # (or 3) or @ (or 2) repeatedly to change playback speed as illustrated below.

To resume normal playback, press PLAY.

JVC HM-HDS1U — Variable-Speed Search/ Reverse Motion Playback diagram (page 31)
Fig. 45 · Variable-Speed Search/ Reverse Motion Playback
JVC HM-HDS1U — Variable-Speed Search/ Reverse Motion Playback diagram (page 31)
Fig. 46 · Variable-Speed Search/ Reverse Motion Playback

Quick Rewind a little

JVC HM-HDS1U — Quick Rewind a little diagram (page 31)
Fig. 47 · Quick Rewind a little

(START –). The unit rewinds the picture a little (about 7 seconds) and resumes playback.

  • If the button is pressed repeatedly, the unit rewinds the pictures continuously and resumes playback.

Quick Skip Forward

JVC HM-HDS1U — Quick Skip Forward diagram (page 31)
Fig. 48 · Quick Skip Forward

During playback (or Live Memory Playback), press (START +). The unit skips forward (about 30 seconds at a time) and resumes playback.

  • If the button is pressed repeatedly, the recorder skips continuously and resumes playback.
Page 32 of the JVC HM-HDS1U user manual — L+R → L → R → L+R
Page 32 · click to enlarge
Page 32

32 EN PLAYBACK FEATURES for HDD deck (cont.)

JVC HM-HDS1U — 32 EN PLAYBACK FEATURES for HDD deck (cont.) diagram (page 32)
Fig. 49 · 32 EN PLAYBACK FEATURES for HDD deck (cont.)

Repeat Playback (Normal Playback Only)

Turn on the TV and select the AV mode.

If the recorder is turned on with HDD deck selected, there may be about 30 seconds' delay in starting to show pictures on the screen.

JVC HM-HDS1U — Repeat Playback (Normal Playback Only) diagram (page 32)
Fig. 50 · Repeat Playback (Normal Playback Only)

During playback, press and hold PLAY (until “ ” blinks on the front display panel), then release. The unit starts playing back the whole program repeatedly up to 100 times. The HDD playback indicator is flashing. To resume normal playback, press PLAY.

JVC HM-HDS1U — Repeat Playback (Normal Playback Only) diagram (page 32)
Fig. 51 · Repeat Playback (Normal Playback Only)

Select The Soundtrack

The HDD deck can record wo soundtracks simulaneously (L and R) and play back the selected one, or both together.

You can select the soundtrack by simply pressing the remote control’s A. MONITOR button as follows:

L+R → L → R → L+R

JVC HM-HDS1U — L+R → L → R → L+R diagram (page 32)
Fig. 52
Page 33 of the JVC HM-HDS1U user manual — STEREO 8:00 PM 9:00 PM 10:00 PM 1CH
Page 33 · click to enlarge
Page 33

EN 33 RECORDING FEATURES for HDD deck

Live Memory Playback (while recording) You can use the following playback features as the Time-Shift Playback while you are recording a program.

Recording Features

  • High-Speed Search
  • Still Picture/Frame-By-Frame Playback
  • Slow Motion/Reverse Slow Motion
  • Variable-Speed Search/Reverse Motion Playback
  • Quick Rewind a little
  • Quick Skip Forward

Record One Program While Watching Another

ENGAGE TV MODE 1

During recording... ●Change the TV’s input mode from AV to TV.

SELECT CHANNEL FOR VIEWING 2

Use the TV’s channel selector to set the channel you want to watch.

Display While Recording

Press OSD. The indication appears on the top of the screen as follows.

  • To clear the indication, press OSD again.

While recording

Current time Recording speed

PRESENT TIME ∞ 9:03 PM EP

Time scale around the current time

REC ÷

STEREO 8:00 PM 9:00 PM 10:00 PM 1CH

Starting point of recording this program

You can enjoy Live Memory Playback in this field.

When using Live Memory Playback while recording

PRESENT TIME ∞ 9:12 PM LIVE MEMORY 3 8:53 PM EP

The time counter using the actual time

STEREO 8:00 PM 9:00 PM 10:00 PM 1CH

The end of this program : The recorder is now recording new pictures in this point.

Pointer for current picture

Show 4 more labels / short text on this page
REC indicator · Audio mode · Recording channel · Current recording point
Page 34 of the JVC HM-HDS1U user manual — Usable cassettes
Page 34 · click to enlarge
Page 34

34 EN SIMPLE OPERATION for VHS deck

LOAD A CASSETTE 1

Simple Playback

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the recorder. Don’t apply too much pressure when inserting.

  • The recorder’s power comes on automatically.
  • The counter is automatically reset to “0:00:00”.
  • If the cassette’s record safety tab has been removed, playback begins automatically.
JVC HM-HDS1U — 34 EN SIMPLE OPERATION for VHS deck diagram (page 34)
Fig. 53 · 34 EN SIMPLE OPERATION for VHS deck

Turn on the TV and select the AV mode.

If the recorder is turned on with HDD deck selected, there may be about 30 seconds' delay in starting to show pictures on the screen.

SELECT VHS DECK 2

Press VHS (or S-VHS). The S-VHS button lights on the front panel.

JVC HM-HDS1U — SELECT VHS DECK 2 diagram (page 34)
Fig. 54

FIND PROGRAM START POINT 3

If the tape is advanced past the start point, press REW. To go forward, press FF.

START PLAYBACK 4

Press PLAY. “VIDEO CALIBRATION” appears on the screen (when VIDEO CALIBRATION is set to “ON” pg. 47). The VHS playback indicator lights on the front panel.

STOP PLAYBACK 5

Press STOP. Then press EJECT on the front panel to remove the cassette.

JVC HM-HDS1U — STOP PLAYBACK 5 diagram (page 34)
Fig. 55

Usable cassettes

VHS deck Full-Size VHS T-30 (ST-30**) T-60 (ST-60**) T-90 T-120 (ST-120**) T-160 (ST-160**) ST-210** Compact VHS* TC-20 (ST-C20**) TC-30 (ST-C30**) TC-40 (ST-C40**) * Compact VHS camcorder recordings can be played on this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette. ** This recorder can record on regular VHS and Super VHS cassettes. While only VHS signals can be recorded on regular VHS cassettes*, both VHS and Super VHS signals can be recorded and played back using Super VHS cassettes.

* By using S-VHS ET it is possible to record and play back with S-VHS picture quality on VHS cassettes with this recorder.

Page 35 of the JVC HM-HDS1U user manual — STOP RECORDING 7
Page 35 · click to enlarge
Page 35

LOAD A CASSETTE 1

Simple Recording

Insert a VHS (or S-VHS) cassette with the record safety tab intact.

If you want to use VHS Navigation to select the pro- gram after recording with this unit, set “VHS NAVIGATION” to “ON” in VHS SET UP 1 of Main Menu before recording. For details, see the next page.

JVC HM-HDS1U — LOAD A CASSETTE 1 diagram (page 35)
Fig. 56

Turn on the TV and select the AV mode.

SELECT VHS DECK 2

If the recorder is turned on with HDD deck selected, there may be about 30 seconds' delay in starting to show pictures on the screen.

Press VHS (or S-VHS). The S-VHS button lights on the front panel.

SELECT RECORDING CHANNEL 3

JVC HM-HDS1U — SELECT RECORDING CHANNEL 3 diagram (page 35)
Fig. 57

Press CH +/–. Or press the appropriate NUMBER keys, then press ENTER. (The channel changes after a few seconds whether you press ENTER or not.)

SET TAPE SPEED 4

Press REC SPEED to select the recording speed from SP or EP.

START RECORDING 5

Press and hold REC and press PLAY on the remote control, or press REC on the recorder’s front panel. The VHS recording indicator lights on the front panel.

Video Calibration takes place at the beginning of both the first SP and the first EP recording after inserting the cassette (when Video Calibration is set to “ON” pg. 47).

JVC HM-HDS1U — START RECORDING 5 diagram (page 35)
Fig. 58

PAUSE/RESUME RECORDING 6

Press PAUSE. Press PLAY to resume recording.

  • During record pause, you can change the recording channel by using the CH +/– buttons or NUMBER keys.

Video Calibration will not take place if the tape speed is changed while in record pause mode.

STOP RECORDING 7

Press STOP. Then press EJECT on the VHS to remove the cassette.

Page 36 of the JVC HM-HDS1U user manual — PLAY STOP MODIFY DELETE
Page 36 · click to enlarge
Page 36

SIMPLE OPERATION for VHS deck (cont.)

The VHS Navigation enables you to seach and select the desired program recorded with the VHS deck very easily. When you record a program with the VHS deck for more than 5 minutes in SP mode (for more than 15 minutes in EP mode) with “NAVIGATION” of “VHS SET UP 1” set to “ON”, its information are registered in the VHS Naviga- tion automatically. When the first program is recorded on a cassette, the VHS Navigation gives the register number to the cas- sette. The VHS Navigation memorizes the cassette by the number. You can confirm the register number of the cassette when the cassette is loaded or ejected. The VHS Navigation can register up to 2000 programs or up tp 680 cassettes.

Playback with VHS Navigation

The following screen appears as the VHS Navigation screen when you press NAVI with the VHS deck selected. You can move the arrow to select the desired position on the screen by pressing @%#fi (or 253∞).

The number appears when the registered cassette is loaded.

Total time and BLANK time of this cassette : based on the recording speed currently selected

VHS NAVI

0001 DATE REC. CATEGORY CASSETTE #

This date shows when the loaded cassette is registered.

[06/12/01 TUE ] 120M BLANK 87M (SP)

NC

Recording Informa- tion for the program indicated by the arrow

BLANK

Index : Small still picture of the each program. In this case, there are two registered programs

06/12/01 TUE 06/12/01 TUE 87min(SP)

[MISC.] 06/12/01 TUE 12:00PM–12:30PM 8CH SP 30min

ST

The icons : they show the recording situation for each program.

PLAY STOP MODIFY DELETE

INDEX NAVI

The Icons and their meanings

NC This program has a little gap at the beginning.

ST This program has stereo sounds.

SA This program has SAP audio.

This program was recorded with Timer recording.

Operational commands · Guidance for operations

Page 37 of the JVC HM-HDS1U user manual — RETURN TO NORMAL SCREEN 5
Page 37 · click to enlarge
Page 37
JVC HM-HDS1U — SIMPLE OPERATION for VHS deck diagram (page 37)
Fig. 59 · SIMPLE OPERATION for VHS deck

Set VHS Navigation

Turn on the TV and select the AV mode.

If the recorder is turned on with HDD deck selected, there may be about 30 seconds' delay in starting to show pictures on the screen. TURN ON THE RECORDER 1

Press POWER.

JVC HM-HDS1U — Set VHS Navigation diagram (page 37)
Fig. 60 · Set VHS Navigation

ACCESS MAIN MENU SCREEN 2

Press MENU.

ACCESS VHS SET UP 1 SCREEN 3

1. At the top of the Main Menu screen, move the arrow to “HDD/ VHS SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) On the HDD/VHS Set Up screen, move the arrow to “VHS SET UP 1” by pressing @# (or 23 ), then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

NAVIGATION ON

VIDEO STABILIZER OFF

TBC ON

VIDEO CALIBRATION ON

PICTURE CONTROL AUTO

INDEX MENU

JVC HM-HDS1U — NAVIGATION ON diagram (page 37)
Fig. 61

SELECT VHS NAVIGATION MODE 4

1. On the VHS Set Up 1 screen, move the arrow to “NAVIGATION” by pressing %fi (or 5∞ ), then press OK . 2) Pressing %fi (or 5∞ ) to select the desired mode, then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

NAVIGATION ON

VIDEO STABILIZER OFF

OFF

ON

TBC ON

VIDEO CALIBRATION ON

PICTURE CONTROL AUTO

INDEX MENU

a– Select “ON” if you want to use the VHS Navigation.

When you set the VHS Navigation to “ON”, “VN” appears on the display of the front panel. b– Select “OFF” if you do not want to use VHS

Navigation.

RETURN TO NORMAL SCREEN 5

Press MENU.

Page 38 of the JVC HM-HDS1U user manual — STOP PLAYBACK 8
Page 38 · click to enlarge
Page 38

SIMPLE OPERATION for VHS deck (cont.)

Scan for Beginning of Program with VHS Navigation

TURN ON THE RECORDER 1

Press POWER.

The VHS Navigation can take effect for the program which has been recorded, and whose information has been registered with this recorder. Once the VHS (S-VHS) cassettes have been used for recording with this recorder, they have the register number given by this recorder.

SELECT VHS DECK 2

Press VHS (or S-VHS). The S-VHS button lights on the front panel.

ACCESS VHS NAVIGATION SCREEN 3

JVC HM-HDS1U — ACCESS VHS NAVIGATION SCREEN 3 diagram (page 38)
Fig. 62

Turn on the TV and select the AV mode.

If the recorder is turned on with HDD deck selected, there may be about 30 seconds' delay in starting to show pictures on the screen.

Press NAVI. The VHS Navigation screen appears.

VHS NAVI

0001 DATE REC. CATEGORY CASSETTE #

[06/12/01 TUE ] 120M BLANK 87M (SP)

BLANK

  • If a registered cassette has been loaded, the contents of the loaded cassette will appear.

06/12/01 TUE 06/12/01 TUE 87min(SP)

JVC HM-HDS1U — VHS NAVI diagram (page 38)
Fig. 63

[MISC.] 06/12/01 TUE 12:00PM–12:30PM 8CH SP 30min

PLAY STOP MODIFY DELETE

INDEX NAVI

SEARCH FOR THE REGISTERED PROGRAM 4

Press @# or 23 to move the arrow to select one of the following search types, then press OK or fi (or ∞).

a– Select the number if you want to select the regis-

tered program from the currently loaded cassette. If no cassette is loaded, “ ” will appear in this position and this is unable to be selected. b– Select “DATE REC.” if you want to search for the

registered program by the recording date. c– Select “CATEGORY” if you want to search for the

registered program by the category in which you have classified the program. d– Select “CASSETTE #” if you want to search for the

JVC HM-HDS1U — PLAY STOP MODIFY DELETE diagram (page 38)
Fig. 64

program by each registered cassette. If you select b, c, or d to search for the program, you must go to screen a after checking the number of the registered cassette including the desired program.

SELECT PROGRAM 5

Press @# (or 23) to move the arrow on the index of the desired program.

START PLAYBACK 6

Press PLAY or OK.

  • If no cassette has been loaded, the register number will be required. In this case, load the cassette with the required number on the VHS deck, then retry.

PAUSE PLAYBACK 7

Press PAUSE.

  • To resume normal playback, press PLAY.

STOP PLAYBACK 8

Press STOP.

Page 39 of the JVC HM-HDS1U user manual — Slow Motion/Reverse Slow Motion
Page 39 · click to enlarge
Page 39

PLAYBACK FEATURES for VHS deck

High-Speed Search

Playback Features

JVC HM-HDS1U — PLAYBACK FEATURES for VHS deck diagram (page 39)
Fig. 65 · PLAYBACK FEATURES for VHS deck

During playback (or Live Memory Playback), press FF for forward high-speed search, or REW for reverse high- speed search.

  • The search speed is 11 times normal playback speed with SP recordings, and 31 times with EP recordings.
JVC HM-HDS1U — PLAYBACK FEATURES for VHS deck diagram (page 39)
Fig. 66 · PLAYBACK FEATURES for VHS deck

To resume normal playback, press PLAY.

Still Picture/Frame-By-Frame Playback

JVC HM-HDS1U — Still Picture/Frame-By-Frame Playback diagram (page 39)
Fig. 67 · Still Picture/Frame-By-Frame Playback
JVC HM-HDS1U — Still Picture/Frame-By-Frame Playback diagram (page 39)
Fig. 68 · Still Picture/Frame-By-Frame Playback

Press PAUSE repeatedly to advance one frame at a time. OR

Press PAUSE for two seconds to start frame-by-frame playback.

To resume normal playback, press PLAY.

Slow Motion/Reverse Slow Motion

JVC HM-HDS1U — Slow Motion/Reverse Slow Motion diagram (page 39)
Fig. 69 · Slow Motion/Reverse Slow Motion

For hands-free slow-motion, press PAUSE during playback (or time-shift playback).

JVC HM-HDS1U — Slow Motion/Reverse Slow Motion diagram (page 39)
Fig. 70 · Slow Motion/Reverse Slow Motion
  • ATTENTION
  • In the high-speed search, still, slow motion or frame-byframe playback mode, the picture will be distorted, and there will be a loss of color.
  • When normal playback resumes from search, still, slow motion or frame-by-frame playback, the picture may jitter vertically momentarily depending on the type of TV being used.

Press ¢ (or 3) for forward slow-motion, or 4 (or 2) for reverse slow-motion.

Press ¢ (or 3) or 4 (or 2) repeatedly. The slow- motion speed changes in three steps for each direction.

To resume normal playback, press PLAY.

Page 40 of the JVC HM-HDS1U user manual — 40 EN PLAYBACK FEATURES for VHS deck (cont.)
Page 40 · click to enlarge
Page 40

40 EN PLAYBACK FEATURES for VHS deck (cont.)

Variable-Speed Search/ Reverse Motion Playback

JVC HM-HDS1U — 40 EN PLAYBACK FEATURES for VHS deck (cont.) diagram (page 40)
Fig. 71 · 40 EN PLAYBACK FEATURES for VHS deck (cont.)
JVC HM-HDS1U — 40 EN PLAYBACK FEATURES for VHS deck (cont.) diagram (page 40)
Fig. 72 · 40 EN PLAYBACK FEATURES for VHS deck (cont.)

During playback (or time-shift playback), press ¢ (or 3) for forward variable-speed search, 4 (or 2) for reverse motion playback.

Press ¢ (or 3) or 4 (or 2) repeatedly to change playback speed as illustrated below.

To resume normal playback, press PLAY.

JVC HM-HDS1U — 40 EN PLAYBACK FEATURES for VHS deck (cont.) diagram (page 40)
Fig. 73 · 40 EN PLAYBACK FEATURES for VHS deck (cont.)
JVC HM-HDS1U — 40 EN PLAYBACK FEATURES for VHS deck (cont.) diagram (page 40)
Fig. 74 · 40 EN PLAYBACK FEATURES for VHS deck (cont.)

Index Search Index codes are placed on the tape at the start of each recording. You can find and automatically play back from the start of any recording using the Index Search function.

JVC HM-HDS1U — 40 EN PLAYBACK FEATURES for VHS deck (cont.) diagram (page 40)
Fig. 75 · 40 EN PLAYBACK FEATURES for VHS deck (cont.)

While the tape is stopped, press # or @ (¢ or 4).

To access a recording 2–9 index codes away, press # or @ repeatedly until the correct number is displayed on screen (only if “SUPERIMPOSE” is set to “ON” ( pg. 41). Playback begins automatically when the desired recording is located.

  • If necessary press REW or FF when play starts to search visually to find the very beginning of the desired program.
Page 41 of the JVC HM-HDS1U user manual — RETURN TO NORMAL SCREEN 4
Page 41 · click to enlarge
Page 41

Superimpose

To recall an indication

This function, switchable between ON and OFF, determines whether or not operational indicators will appear on screen.

1 Press OSD. All indications corresponding to the current status are

displayed for 5 seconds. After that, the counter information and RECORD/PAUSE if in the Record Pause mode, are left displayed on the screen. 2 Press OSD again to clear the display. The RECORD/PAUSE indication is left displayed on the

ACCESS MAIN MENU SCREEN 1

Press MENU.

screen.

  • If you want to stop the following procedure on its way, press MENU .
  • NOTES:
  • If you engage the Record Pause mode, RECORD/PAUSE is displayed regardless of the Superimpose mode setting.
  • If you select a channel on which no signal is received, the channel number is displayed regardless of the Superimpose mode setting.

ACCESS FUNCTION SCREEN 2

1. At the top of Main Menu screen, move the arrow to “FUNCTION SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) On the Function Set Up screen, move the arrow to “FUNCTION” by pressing @# (or 23 ), then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VIDEO INPUTS FUNCTION

SUPERIMPOSE OFF

The superimposed indication on the TV screen tells you what the recorder is doing.

BLUE BACK ON

2ND AUDIO RECORD OFF

INDEX MENU

CH 125 RECORD THU 12:00 AM PAUSE STEREO ] SP SAP VHS

B E + + +

INDEX-1 NORM HI–FI COUNT –1:23:45

SELECT SUPERIMPOSE MODE 3

VHS

1. Tuned-in channel or AUX(iliary) mode
1. On the Function screen, move the arrow to “SUPERIMPOSE” by pressing %fi (or 5∞ ), then press OK . 2) Press %fi (or 5∞ ) to select the desired mode, then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VIDEO INPUTS FUNCTION

When the channel is changed, the new channel is displayed on the screen for 5 seconds. 2– Clock time 3– Stereo program indication 4– Second Audio Program indication 5– VHS indicator 6– Audio mode indications 7– “Cassette Loaded” mark

SUPERIMPOSE OFF

OFF ON

BLUE BACK ON

2ND AUDIO RECORD OFF

INDEX MENU

When a cassette is loaded, the mark is displayed for 5 seconds. It blinks when the recorder’s EJECT button is pushed. 8– Operation mode

a– Select “ON” if you want the superimposed opera-

tional indications on the screen about 5 seconds when operating the recorder. b– Select “OFF” if you do not want the superimposed

When the operation mode is changed, the new mode is displayed — RECORD (5 sec.), PLAY (5 sec.), FF/REW (5 sec. when engaged from Stop mode), RECORD PAUSE (for as long as Pause is engaged), and ITR *:** (5 sec.). 9– Tape speed indication 10– Tape position indicator 11– INDEX indication 12– Counter reading Switchable to the tape remaining time display

operational indications on the screen.

RETURN TO NORMAL SCREEN 4

Press MENU.

Page 42 of the JVC HM-HDS1U user manual — Repeat Playback
Page 42 · click to enlarge
Page 42

42 EN PLAYBACK FEATURES for VHS deck (cont.)

Manual Tracking

Once playback begins, the VCR’s automatic tracking function is engaged. If tracking noise appears in the picture, you can override this and make the adjustment manually.

JVC HM-HDS1U — 42 EN PLAYBACK FEATURES for VHS deck (cont.) diagram (page 42)
Fig. 76 · 42 EN PLAYBACK FEATURES for VHS deck (cont.)
JVC HM-HDS1U — 42 EN PLAYBACK FEATURES for VHS deck (cont.) diagram (page 42)
Fig. 77 · 42 EN PLAYBACK FEATURES for VHS deck (cont.)

During playback, press CH +/– on the front panel simultaneously to cancel the automatic tracking mode and enable manual tracking adjust. ADJUST MANUAL TRACKING 2

Press CH + or – on the front panel or remote. Press briefly for fine adjust, or press and hold for coarse adjust. Watch the screen and continue adjusting until optimum picture and sound quality are achieved. RE-ENGAGE AUTOMATIC TRACKING 3

JVC HM-HDS1U — 42 EN PLAYBACK FEATURES for VHS deck (cont.) diagram (page 42)
Fig. 78 · 42 EN PLAYBACK FEATURES for VHS deck (cont.)
  • When automatic tracking is re-engaged, Video Calibration is automatically activated.
  • NOTES:
  • To obtain a noiseless still picture it may be necessary to adjust tracking in slow playback and then engage Pause.
  • Manual tracking is possible during hands-free slow-motion. During hands-free slow-motion playback, simply press CH + or – on the recorder’s front panel or remote to adjust tracking.

Repeat Playback

JVC HM-HDS1U — Repeat Playback diagram (page 42)
Fig. 79 · Repeat Playback

Press and hold PLAY (until " " blinks on the front display panel) during playback, then release.

  • The entire tape is played back 100 times. STOP REPEAT 2

To stop, press STOP at any time. NOTE: Pressing PLAY, REW, FF, PAUSE or ™ £ also stops Repeat Playback.

Page 43 of the JVC HM-HDS1U user manual — B E + + +
Page 43 · click to enlarge
Page 43

Counter Reset

JVC HM-HDS1U — Counter Reset diagram (page 43)
Fig. 80 · Counter Reset
JVC HM-HDS1U — Counter Reset diagram (page 43)
Fig. 81 · Counter Reset

Press C.RESET. NOTE: By pressing the DISPLAY button, you can change the display to show the counter reading, channel number, clock time or tape remaining time. (Channel number is not displayed during playback.)

Next-Function Memory

The Next Function Memory “tells” the recorder what to do after rewinding. Before continuing, ensure that the recorder is in stop mode. a – For Automatic Start Of Playback After Tape Rewind press REW, then press PLAY within 2 seconds.

JVC HM-HDS1U — Next-Function Memory diagram (page 43)
Fig. 82 · Next-Function Memory

b – For Automatic Ejection Of Cassette After Tape Rewind press REW, then press EJECT within 2 seconds.

Tape Position Indicator

  • The Tape position indicator appears on screen when, from the stop mode, you press FF , REW , or perform an Index Search. The position of “ ” in relation to “B“ (Beginning) or “E“ (End) shows you where you are on the tape. NOTES:
  • “SUPERIMPOSE” must be set to “ON”, or the indicator will not appear ( pg. 41).
  • It may take a few seconds for the Tape Position Indicator to be displayed.

B E + + +

COUNT 0:33:27

Page 44 of the JVC HM-HDS1U user manual — RETURN TO NORMAL SCREEN 4
Page 44 · click to enlarge
Page 44

44 EN PLAYBACK FEATURES for VHS deck (cont.)

Picture Control

ACCESS MAIN MENU SCREEN 1

This feature helps you to adjust the playback picture quality according to your preference. *The default setting is “AUTO.”

Press MENU.

ACCESS VHS SET UP 1 SCREEN 2

1. At the top of the Main Menu screen, move the arrow to “HDD/VHS SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) On the HDD/VHS Set Up screen, move the arrow to “VHS SET UP 1” by pressing @# (or 23 ), then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

JVC HM-HDS1U — ACCESS VHS SET UP 1 SCREEN 2 diagram (page 44)
Fig. 83

VHS SET UP 1 VHS SET UP 2 HDD SET UP

NAVIGATION ON

VIDEO STABILIZER OFF

TBC ON

VIDEO CALIBRATION ON

PICTURE CONTROL AUTO

INDEX MENU

SELECT PICTURE CONTROL MODE 3

1. On the VHS Set Up 1 screen, move the arrow to “PICTURE CONTROL” by pressing %fi (or 5∞ ), then press OK . 2) Pressing %fi (or 5∞ ) to select the desired mode, then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

NAVIGATION ON

JVC HM-HDS1U — NAVIGATION ON diagram (page 44)
Fig. 84

VIDEO STABILIZER OFF

TBC ON

AUTO

EDIT SOFT SHARP

VIDEO CALIBRATION ON

PICTURE CONTROL AUTO

INDEX MENU

AUTO*: Normally select “AUTO”.

It automatically adjusts the picture quality. * When “VIDEO CALIBRATION” is set to “OFF” ( pg. 47), you can only select NORM instead of AUTO. EDIT: Select when you dub tapes. SOFT: Select when you want to soften the picture. SHARP: Select when you want to sharpen the picture.

  • NOTE:
  • When you select “EDIT”, “SHARP" or “SOFT”, the selected mode will not change until you select again.
  • When you select “EDIT" to dub tapes, be sure to select “AUTO” (or “NORM” when “VIDEO CALIBRATION” is set to “OFF”) after you finish dubbing the tapes.

RETURN TO NORMAL SCREEN 4

Press MENU.

Page 45 of the JVC HM-HDS1U user manual — Video Stabilizer
Page 45 · click to enlarge
Page 45

Video Stabilizer

JVC HM-HDS1U — Video Stabilizer diagram (page 45)
Fig. 85 · Video Stabilizer

By activating the Video Stabilizer you can correct vertical vibrations in the picture when playing back unstable EP recordings that were made on another VCR. When this function is set to “ON”, vertical vibration will be automatically cor- rected. *The default setting is “OFF”.

1. At the top of the Main Menu screen, move the arrow to “HDD/VHS SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) On the HDD/VHS Set Up screen, move the arrow to “VHS SET UP 1” by pressing @# (or 23 ), then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

JVC HM-HDS1U — Video Stabilizer diagram (page 45)
Fig. 86 · Video Stabilizer
1. On the VHS Set Up 1 screen, move the arrow to “VIDEO STABILIZER” by pressing %fi (or 5∞ ), then press OK . 2) Pressing %fi (or 5∞ ) to select the desired mode, then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

JVC HM-HDS1U — Video Stabilizer diagram (page 45)
Fig. 87 · Video Stabilizer
  • NOTES:
  • When you finish viewing the tape, be sure to set it back to “OFF”.
  • Regardless of the setting, this function has no effect during recording and during special-effects playback.
  • The Superimpose mode indications may jitter vertically when “VIDEO STABILIZER” is set to “ON”.
  • To watch recordings with close-caption, it is necessary to set the Video Stabilizer function to “OFF”.
Page 46 of the JVC HM-HDS1U user manual — NAVIGATION ON
Page 46 · click to enlarge
Page 46

46 EN PLAYBACK FEATURES for VHS deck (cont.)

  • NOTES:
  • If you play back a tape recorded under poor TV reception condition, there may be cases where the picture becomes more stable with Digital TBC set to off.
  • When Digital TBC is set to on, if you play back a tape where certain types of signals are recorded (using a PC or some character generators), the playback picture may be distorted. If this is the case, turn off Digital TBC.
  • Digital TBC and Video Stabilizer ( pg. 45) cannot be used at the same time; if you turn on Digital TBC when "VIDEO STABILIZER" is set to "ON", Video Stabilizer will be automatically turned "OFF". Make sure Digital TBC is off when you want to use Video Stabilizer. ACCESS MAIN MENU SCREEN 1

TBC

Your recorder is equipped with the TBC (Time Base Corrector) that removes jitter from fluctuating video signals to deliver a stable picture even with old tapes and rental cassettes. The on/off of Digital 3-DNR (Noise Reduction) which cuts noise and enables clear picture reproduction is also linked to this function. * The default setting is “ON”. We recommend that you use the TBC feature when playing back a tape recorded on a camcorder playing back a tape repeatedly used using this recorder as the player for editing.

Select The Soundtrack

Press MENU.

The VHS deck can record two soundtracks simultaneously (Normal and Hi-Fi) and play back the selected one, or both together. Or, when viewing a pre-recorded tape that contains two separate Hi-Fi audio programs, you can choose to listen to either one by selecting either "Hi-Fi L" or "Hi-Fi R".

ACCESS VHS SET UP 1 SCREEN 2

1. At the top of the Main Menu screen, move the arrow to “HDD/VHS SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) On the HDD/VHS Set Up screen, move the arrow to “VHS SET UP 1” by pressing @# (or 23 ), then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

You can select the soundtrack by simply pressing the remote control's A. MONITOR button as follows:

NAVIGATION ON

VIDEO STABILIZER OFF

TBC ON

Hi-Fi → Hi-Fi L → Hi-Fi R → Normal → Mix → Hi-Fi

VIDEO CALIBRATION ON

PICTURE CONTROL AUTO

INDEX MENU

SELECT TBC MODE 3

1. On the VHS Set Up 1 screen, move the arrow to “TBC” by pressing %fi (or 5∞ ), then press OK . 2) Pressing %fi (or 5∞ ) to select the desired mode, then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

NAVIGATION ON

VIDEO STABILIZER OFF

TBC ON

VIDEO CALIBRATION ON

OFF

ON

PICTURE CONTROL AUTO

INDEX MENU

RETURN TO NORMAL SCREEN 4

Press MENU.

Page 47 of the JVC HM-HDS1U user manual — Preparation
Page 47 · click to enlarge
Page 47

Preparation

Active Video Calibration

Active Video Calibration checks the condition of the tape during recording and playback, and compensates for poor reproduction to provide the best quality recording and playback pictures. *The default setting is “ON”.

JVC HM-HDS1U — Preparation diagram (page 47)
Fig. 88 · Preparation

Turn on the TV and select the AV mode. TURN ON THE RECORDER 1

JVC HM-HDS1U — Preparation diagram (page 47)
Fig. 89 · Preparation
1. At the top of the Main Menu screen, move the arrow to “HDD/VHS SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) On the HDD/VHS Set Up screen, move the arrow to “VHS SET UP 1” by pressing @# (or 23 ), then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

JVC HM-HDS1U — Preparation diagram (page 47)
Fig. 90 · Preparation
1. On the VHS Set Up 1 screen, move the arrow to “VIDEO CALIBRATION” by pressing %fi (or 5∞ ), then press OK . 2) Pressing %fi (or 5∞ ) to select the desired mode, then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

Page 48 of the JVC HM-HDS1U user manual — Accidental erasure prevention
Page 48 · click to enlarge
Page 48

PLAYBACK FEATURES for VHS deck (cont.)

Recording

JVC HM-HDS1U — PLAYBACK FEATURES for VHS deck (cont.) diagram (page 48)
Fig. 91 · PLAYBACK FEATURES for VHS deck (cont.)

Perform steps 1 – 4 on page 35 (“Simple Recording”) before continuing.

START RECORDING 1

Press and hold REC and press PLAY on the remote control, or press REC on the recorder’s front panel.

DURING CALIBRATION

  • The recorder takes about 7 seconds to assess the quality of the tape in use, then recording begins with the picture level optimized.

START END

+

ACTIVE VIDEO CALIBRATION

  • NOTES:
  • Calibration occurs immediately prior to both the first SP and the first EP recording after inserting the cassette. It does not take place during recording.
  • In the case of timer recording, calibration takes place for both SP and EP before the first timer recording after inserting the cassette (regardless of the tape speed selected for that recording).
  • Once the cassette is ejected, the calibration data is canceled. The next time the cassette is used for recording, calibration is re-performed.
  • While Video Calibration is operative, the PAUSE button will not function.
  • To display the Video Calibration screen, “SUPERIMPOSE” must be set to “ON” or the Video Calibration screen will not appear ( pg. 41).

CALIBRATION COMPLETE

START END

+

ACTIVE VIDEO CALIBRATION

Playback

The recorder assesses the quality of the tape once you start playback.

there is a delay of about 7 seconds after REC and PLAY on the remote, or REC on the recorder’s front panel, are pressed. To make sure you record the desired scene or program completely, first perform the following steps: 1) Press and hold PAUSE, and press REC to engage the RECORD PAUSE mode. ●The VCR then automatically checks the condition of the tape and, after about 7 seconds, re-enters RECORD PAUSE. 2) Press PLAY to start recording. If you want to bypass Video Calibration and start

Perform steps 1 – 3 on page 34 (“Simple Playback”) before continuing.

START PLAYBACK 1

Press PLAY.

  • The recorder adjusts the playback picture quality based on the quality of the tape in use.

VIDEO CALIBRATION

recording right away, set “VIDEO CALIBRATION” to "OFF" in step 3 of the Preparation procedure ( pg. 47).

  • NOTES:
  • When using rental tapes, or tapes recorded on other VCRs, set “VIDEO CALIBRATION” in step 3 of the Preparation procedure to either “ON” or “OFF” as desired to give the best picture ( pg. 47).
  • The Video Calibration screen only appears at the beginning of automatic tracking. Even though the screen doesn't appear after that, the Video Calibration function is operative.
  • To display the Video Calibration screen, “SUPERIMPOSE” must be set to “ON” or the Video Calibration screen will not appear ( pg. 41.)

Accidental erasure prevention

JVC HM-HDS1U — Accidental erasure prevention diagram (page 48)
Fig. 92 · Accidental erasure prevention
  • VHS/S-VHS To prevent accidental recording on a recorded cassette, remove its safety tab. To record on it later, cover the hole with adhesive tape. Record safety tab
Page 49 of the JVC HM-HDS1U user manual — Record One Program While Watching Another
Page 49 · click to enlarge
Page 49

EN 49 RECORDING FEATURES for VHS deck

Display Elapsed Recording Time

Recording Features

RESET COUNTER TO ZERO 1

Before recording starts, press C.RESET. The counter resets to zero and displays the exact elapsed time as the tape runs. DISPLAY ELAPSED TIME ON SCREEN 2

JVC HM-HDS1U — EN 49 RECORDING FEATURES for VHS deck diagram (page 49)
Fig. 93 · EN 49 RECORDING FEATURES for VHS deck

During recording, press OSD at any time to see the elapsed time. All indications corresponding to the current status of the recorder are displayed for 5 seconds. The counter display remains on the screen indicating the elapsed time. Press OSD again to remove the display.

  • Make sure “SUPERIMPOSE” is set to “ON“ ( pg. 41).
  • The indications are not recorded.
  • Press OSD to change to the COUNT display if “REMAIN” is displayed.

Display Tape Remaining Time (VHS deck only)

DISPLAY COUNTER INFORMATION 1

Press OSD. All indications corresponding to the recorder’s current status are displayed for 5 seconds. The counter display remains on the screen indicating the elapsed time. DISPLAY TAPE REMAINING TIME 2

Press OSD repeatedly until “REMAIN” appears on screen. The approximate tape remaining time appears on the TV screen and also on the recorder display panel with a " " indicator.

  • The tape remaining time is calculated based on the tape speed (SP or EP) being used. The indicated remaining time is only an estimate.
  • Press OSD to change the on-screen display from “REMAIN” to “COUNT” and vice versa; and to show counter reading, channel number, clock time or tape remaining time on the front display panel. Then channel number will not be displayed when the recorder is playing a tape. EXIT THE DISPLAY 3

Record One Program While Watching Another

Press OSD again.

JVC HM-HDS1U — Record One Program While Watching Another diagram (page 49)
Fig. 94 · Record One Program While Watching Another

During recording... ●Change the TV's input mode from AV to TV.

  • NOTES:
  • “SUPERIMPOSE” must be set to “ON”, or the on-screen display will not appear ( pg. 41).
  • Near the beginning of the tape, the tape remaining estimate may be inaccurate. However, the estimate becomes more accurate as the tape comes closer to the end.
  • Depending on the type of tape used, the tape remaining time reading may not appear right away, or may not be correct. "- -:- -" may sometimes appear, or the display may blink on occasion.
  • The tape remaining time indication is not accurate when using VHS-C tapes with VHS-C adapter.

Use the TV’s channel selector to set the channel you want to watch.

Page 50 of the JVC HM-HDS1U user manual — RECORDING FEATURES for VHS deck (cont.)
Page 50 · click to enlarge
Page 50

RECORDING FEATURES for VHS deck (cont.)

S-VHS (Super VHS), S-VHS ET and VHS

JVC HM-HDS1U — RECORDING FEATURES for VHS deck (cont.) diagram (page 50)
Fig. 95 · RECORDING FEATURES for VHS deck (cont.)

Your recorder can record in S-VHS, S-VHS ET or VHS. S-VHS allows you to make high quality video recordings with a horizontal resolution of 400 lines. This compares with the 240 lines of resolution of normal VHS recordings. To achieve the highest quality picture we recommend that you record in S-VHS mode. By using S-VHS ET it is possible to record and play back with S- VHS picture quality on VHS cassettes with this recorder. For details, refer to the next page.

1. At the top of the Main Menu screen, move the arrow to “HDD/ VHS SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) On the HDD/VHS Set Up screen, move the arrow to “VHS SET UP 2” by pressing @# (or 23 ), then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

JVC HM-HDS1U — RECORDING FEATURES for VHS deck (cont.) diagram (page 50)
Fig. 96 · RECORDING FEATURES for VHS deck (cont.)
1. On the VHS Set Up 2 screen, move the arrow to “S-VHS MODE” by pressing %fi (or 5∞ ), then press OK . 2) Pressing %fi (or 5∞ ) to select the desired mode, then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

  • To record in S-VHS;
  • perform the steps 1 – 4 below to set the “S-VHS MODE” to “ON”.
  • then, insert a cassette marked “S-VHS”, the S-VHS indicator will light on the display panel. The S-VHS recording mode will be automatically selected. To record in S-VHS ET on a VHS high grade cassette;
  • press S-VHS ET and set to “ON”. “Super VHS ET” on the next page. To record in VHS;
  • insert a cassette marked “VHS”.
  • press S-VHS ET and set to “OFF”. The VHS recording mode will be automatically selected regardless of the S-VHS mode setting.
  • To record in VHS on an S-VHS cassette;
  • insert the cassette marked “S-VHS”, the S-VHS indicator will light on the display panel.
  • then, perform the steps 1 – 4 below to set the “S-VHS MODE” to “OFF”; the S-VHS indicator will go out. The VHS recording mode will be selected.
Page 51 of the JVC HM-HDS1U user manual — Super VHS ET
Page 51 · click to enlarge
Page 51

Super VHS ET

JVC HM-HDS1U — Super VHS ET diagram (page 51)
Fig. 97 · Super VHS ET

Your recorder is equipped with Super VHS ET that makes it possible to record with S-VHS picture quality on VHS cassettes.

Press S-VHS ET on the front panel. You can check the current setting (“S-VHS ET : ON” or “S-VHS ET : OFF”) if “SUPERIMPOSE” is set to “ON” (pg. 41). If “S-VHS ET : OFF” appears on the TV screen, press S-VHS ET again in about 5 seconds later to set it “ON”.

  • The S-VHS indicator lights up on the front display panel.

To cancel S-VHS ET, press the button again.

JVC HM-HDS1U — Super VHS ET diagram (page 51)
Fig. 98 · Super VHS ET

pg. 64) is in progress while Video Calibration ( pg. 47) is in progress when the recorder’s power is off. ●S-VHS ET does not work with S-VHS tapes.

S-VHS ET This facility allows recording with S-VHS picture quality on VHS cassettes. You can play back those cassettes recorded in S-VHS ET on a VCR equipped with S-VHS ET.

  • NOTES:
  • To obtain the highest quality recording and playback pictures over a longer period on this model, S-VHS recording on S-VHS tape is recommended.
  • You can play back S-VHS ET recordings not only on this recorder but also on another VHS VCR equipped with SVHS ET. * It is recommended to specifically label S-VHS ET recordings so you can easily distinguish them from regular VHS recordings.
  • S-VHS ET recordings can also be played back on an SVHS VCR or a VHS VCR equipped with SQPB (S-VHS QUASI PLAYBACK) function. However, there may be cases where S-VHS ET playback is not possible on a particular VCR.
  • Frequent still, frame-by-frame and slow-motion playback may damage the tape and cause picture degradation.
  • With some tapes, better picture quality may not be obtained even with S-VHS ET recording. It is recommended that you do test record beforehand to make sure whether better results can be obtained.
  • High Grade tapes are recommended for superior results.
  • Make sure that “VIDEO CALIBRATION” is set to “ON” at the Function screen ( pg. 47).
  • During S-VHS ET playback, noise may appear depending on tape quality.
  • Noise may appear during still, frame-by-frame and slowmotion playback.
  • If the playback picture becomes blurred or interrupted, use a cleaning cassette.
Page 52 of the JVC HM-HDS1U user manual — 52 EN RECORDING FEATURES for VHS deck (cont.)
Page 52 · click to enlarge
Page 52

52 EN RECORDING FEATURES for VHS deck (cont.)

Retake (VHS deck only)

JVC HM-HDS1U — 52 EN RECORDING FEATURES for VHS deck (cont.) diagram (page 52)
Fig. 99 · 52 EN RECORDING FEATURES for VHS deck (cont.)

You can cut out unnecessary parts of a TV program while you're recording it.

Hold down REW or FF and release it when you reach the point where you want to resume recording. * Your recorder returns to the Record-Pause mode. RESUME RECORDING 3

JVC HM-HDS1U — 52 EN RECORDING FEATURES for VHS deck (cont.) diagram (page 52)
Fig. 100 · 52 EN RECORDING FEATURES for VHS deck (cont.)
JVC HM-HDS1U — 52 EN RECORDING FEATURES for VHS deck (cont.) diagram (page 52)
Fig. 101 · 52 EN RECORDING FEATURES for VHS deck (cont.)
JVC HM-HDS1U — 52 EN RECORDING FEATURES for VHS deck (cont.) diagram (page 52)
Fig. 102 · 52 EN RECORDING FEATURES for VHS deck (cont.)

Go back to end of program to cut out unnecessary part

End of program · Beginning of program

Page 53 of the JVC HM-HDS1U user manual — Stereo And SAP (Second Audio Program)
Page 53 · click to enlarge
Page 53

Stereo And SAP (Second Audio Program)

JVC HM-HDS1U — Stereo And SAP (Second Audio Program) diagram (page 53)
Fig. 103 · Stereo And SAP (Second Audio Program)
  • Your recorder’s built-in MTS decoder enables reception of Multichannel TV Sound broadcasts. When the channel is changed on the recorder ...
  • The “STEREO” indication appears on the screen for about 5 seconds if the program is a stereo broadcast.
  • The “SAP” indication appears on the screen for about 5 seconds if the program is a SAP broadcast.
  • Both indications appear when a stereo program is accompanied by SAP audio.

To Record Stereo Programs . . .. . . simply follow the basic recording procedure.

1. At the top of Main Menu screen, move the arrow to “FUNCTION SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) On the Function Set Up screen, move the arrow to “FUNCTION” by pressing @# (or 23 ), then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

To Listen To Stereo Soundtrack During Recording . . .. . . press A. MONITOR to select “HI-FI” ( pg. 46).

JVC HM-HDS1U — Stereo And SAP (Second Audio Program) diagram (page 53)
Fig. 104 · Stereo And SAP (Second Audio Program)
1. On the Function screen, move the arrow to “2ND AUDIO RECORD” by pressing %fi (or 5∞ ), then press OK . 2) Press %fi (or 5∞ ) to select the desired mode, then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

JVC HM-HDS1U — Stereo And SAP (Second Audio Program) diagram (page 53)
Fig. 105 · Stereo And SAP (Second Audio Program)
  • NOTES:
  • If a SAP program is received and “2ND AUDIO RECORD” is set to “ON”, the SAP audio is recorded on both the Normal and Hi-Fi tracks. The main audio program is not recorded.
  • If a non-SAP program is received, the main audio is recorded on both the Hi-Fi and Normal audio tracks.
Page 54 of the JVC HM-HDS1U user manual — TRANSFER THE PLUSCODE TO THE UNIT 5
Page 54 · click to enlarge
Page 54

TIMER RECORDING

Timer recording allows you to program the recorder to automati- cally record a program that will be broadcast at some future time. The timer record function can be programmed using the VCR Plus+ or Express Timer programming ( pg. 58) up to 16 shows each on the HDD and VHS decks as far as a year in advance. The VCR Plus+ timer programming system eliminates the need to input channel, date, start and stop time data when setting the timer record function. Simply key in the PlusCode number for the TV program you wish to record and the recorder’s timer will be automatically programmed. (The PlusCode programming numbers are the numbers next to the program in most TV listing.)

VCR Plus+ ® Timer Programming

JVC HM-HDS1U — VCR Plus+ ® Timer Programming diagram (page 54)
Fig. 106 · VCR Plus+ ® Timer Programming

Turn on the TV and select the AV mode. TURN ON THE RECORDER 1

Press POWER.

SELECT THE DECK 2

Press HDD or VHS (or S-VHS).

ACCESS VCR PLUS+ SCREEN 3

Press VCR PLUS on the remote control. The indication for VCR PLUS+ appears on the display window of the remote control.

–

ENTER PLUSCODE NUMBER 4

Press the appropriate NUMBER keys to enter the PlusCode number printed in the TV listings for the TV program you wish to record.

JVC HM-HDS1U — – – – – – – – – – diagram (page 54)
Fig. 107

1 2 3 –

  • To make corrections, press CANCEL and input the correct PlusCode number.
  • If you want to stop programming the timer recording, press VCR PLUS on the remote control. The indication on the remote control disappears.

TRANSFER THE PLUSCODE TO THE UNIT 5

Press TRANS to transmit the PlusCode number from the remote control to the recorder. If “SET GUIDE CHANNEL THEN RETRY” appears on the screen, perform VCR Plus+ setup procedure. ( page 56.) When “PROGRAM FULL DELETE UNWANTED TIMER PROGRAM” appears on the screen, you need to cancel some of the reserved programs. ( page 61.)

Page 55 of the JVC HM-HDS1U user manual — SP = EP = SP = ···
Page 55 · click to enlarge
Page 55

CHECK PROGRAM DATA 6

IMPORTANT If you have moved to a different area or if a broadcasting station´s channel number has been changed, the wrong VCR or CABLE CH number will be displayed on the VCR Plus+ program screen in step 6. When this happens, set the correct the Guide Channel number for that station. ( pg. 56, “Changing VCR Plus+® Setting”)

The PlusCode number you entered and the matching Timer- Recording information are displayed on the Program screen. Check to make sure their correct.

PROGRAM

PLUS CODE NO. 1 2 3 6 5

RECORD TO

SPEED DAIRY/WEEKLY

SOURCE

HDD SEP WEEKLY

CATV

START TIME STOP TIME DATE

11:30 PM 12:00 AM 06/12/01 TUE 5 CH

CONFIRM CANCEL CATEGOTY MISC.

PROG. SET PROPGRAM WITH [EXPRESS +/–, 8=DAILY, 9=WEEKLY, 7=DBS] THEN PRESS "CONFIRM"

START

STOP

DATE

CH END

  • NOTES:
  • To disengage the timer before recording starts, press TIMER again. Pressing once more re-engages it.
  • In case of a power failure after programming, the recorder’s memory backup keeps your selections for approximately 60 minutes.
  • When timer-recording cable channels received through a Cable Box, be sure to keep the Cable Box set to ON.
  • It is not possible to timer-record the same programme on both the VHS deck and the HDD deck simultaneously.
  • If the times that are programmed for recording on the HDD deck and on the VHS deck overlap, the earlier start time takes precedence. If the start times are the same, the VHS deck takes precedence.
  • To change the stop time, press STOP +/– .
  • To timer-record daily or weekly serials, press DAILY ( NUMBER key “8”) or WEEKLY ( NUMBER key “9”). “DAILY” or “WEEKLY” appears on the Program screen. Pressing the button again makes each corresponding display disappear.
  • You can also set category. 1) Press @# (or 23 ) to move the arrow to “CATEGORY”, then press OK . The Category Set screen appears. 2) Select the desired category by pressing @%#fi (or 253∞ ), then press OK . 2) Confirm the arrow is on the “RETURN”, then press OK . The Program screen resumes.
  • If you want to cancel this reservation, move the arrow to “CANCEL” by pressing @# (or 23 ), then press OK . Or, press PROG .

CATEGORY

CHILDRENS

CLASSICS

COMEDY DRAMA

NEWS EDUCATIONS

MOVIES

MUSIC

RELIGIOUS

SERIES

SHOPPING

SPECIAL

SOAPS

SPORTS

OTHERS

MISC.

RETURN

SET TAPE SPEED 7

Press REC SPEED. Each time the button is pressed, the recording speed changes as follows:

For HDD deck:

SP = LP = EP = SEP = SP = ··· For VHS deck:

SP = EP = SP = ···

RETURN TO NORMAL SCREEN 8

Move the arrow to “CONFIRM” by pressing @%#fi (or 253∞), then press OK. “PROGRAM COMPLETED” appears on the screen for a while, then normal screen appears.

  • If there is a conflict in the timer schedule and one program overlaps with another, the correction screen will appear. In this case, correct the program data. See page 60.
  • If you select VHS deck, press TIMER . The recorder turns off automatically and " ‰ " is displayed on the display panel.
Show 4 more labels / short text on this page
+ – · + – · + – · + –
Page 56 of the JVC HM-HDS1U user manual — VCR Plus+ Guide Channel Matching
Page 56 · click to enlarge
Page 56

56 EN TIMER RECORDING (cont.)

JVC HM-HDS1U — 56 EN TIMER RECORDING (cont.) diagram (page 56)
Fig. 108 · 56 EN TIMER RECORDING (cont.)

Changing VCR Plus+ ® Setting

Turn on the TV and select the AV mode.

To ensure that the VCR Plus+Timer Recording operates correctly it is necessary to set the VCR Plus+ “Guide Channel Set” for each station. Please read the following information carefully.

VCR Plus+ Guide Channel Matching

JVC HM-HDS1U — VCR Plus+ Guide Channel Matching diagram (page 56)
Fig. 109 · VCR Plus+ Guide Channel Matching

VCR Plus+ programming system assigns a VCR Plus+ “Guide Channel” to broadcast and cable TV channels. These Guide Channel numbers are also called the VCR Plus+ Channel Codes. Most TV listings have a section, usually a chart, indicating the “Guide Channel” numbers assigned to each station. For accurate VCR Plus+ programming the VCR Plus+ Guide Channel number for each station should match the channel number on which it is received in your area.

  • NOTES:
  • In many instances the VCR Plus+ Guide Channel numbers for cable and broadcast TV stations DO NOT match the channel number on which it is received by your recorder or cable box. Check your TV listing, or contact your cable supplier for details.
  • Many broadcast TV stations can be viewed on cable. Check your TV listing, or contact your cable supplier for details.
JVC HM-HDS1U — VCR Plus+ Guide Channel Matching diagram (page 56)
Fig. 110 · VCR Plus+ Guide Channel Matching
JVC HM-HDS1U — VCR Plus+ Guide Channel Matching diagram (page 56)
Fig. 111 · VCR Plus+ Guide Channel Matching
1. At the top of Main Menu screen, move the arrow to “INITIAL SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) At the Initial Set Up screen, move the arrow to “INITIAL SET” by pressing @# (or 23 ), then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

CLOCK SET GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET

Page 57 of the JVC HM-HDS1U user manual — RETURN TO NORMAL SCREEN 7
Page 57 · click to enlarge
Page 57

ACCESS GUIDE CHANNEL SET SCREEN 4

Press %fi (or 5∞) to move the arrow to “GUIDE CHANNEL SET”, then press # (or 3) or OK.

INITIAL SET

CLOCK SET GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET

JVC HM-HDS1U — INITIAL SET diagram (page 57)
Fig. 112

SELECT WITH[5,∞] THEN[OK] PRESS[MENU] TO END

INPUT GUIDE CHANNEL NUMBER 5

(Ex.) When inputting the Guide Channel number 6 for WNJU(Ind.)

Press %fi (or 5∞) or the appropriate NUMBER keys to input the VCR Plus+ Guide Channel number as shown in the TV listing. Then press # (or 3) or OK.

GUIDE CHANNEL SET

GUIDE CH: 6

CABLE CH: ––

JVC HM-HDS1U — GUIDE CHANNEL SET diagram (page 57)
Fig. 113

PRESS NUMBER KEY(0-9) OR(5,∞), THEN(OK) PRESS(MENU) TO END

  • If you receive your channels with a cable box and if you do not have properly set your Controller, “CABLE CH” appears in place of “VCR CH”. If so, refer to pages 15 – 17 and re-perform the procedure.

INPUT RECEIVING CHANNEL NUMBER 6

(Ex.) If WNJU(Ind.) is received on channel 47

Press %fi (or 5∞) or the appropriate NUMBER keys to input the number of the channel on which the Guide Channel’s broadcasts are received. Then press # (or 3) or OK.

GUIDE CHANNEL SET

GUIDE CH: 6

CABLE CH: 47

PRESS NUMBER KEY(0-9) OR(5,∞), THEN(OK) PRESS(MENU) TO END

  • Repeat steps 5 and 6 for each instance.

RETURN TO NORMAL SCREEN 7

Press MENU twice.

=

Page 58 of the JVC HM-HDS1U user manual — SET PROGRAM STOP TIME 6
Page 58 · click to enlarge
Page 58

58 EN TIMER RECORDING (cont.)

You can directly program the recorder’s timer to record up to 16 shows each on the HDD and VHS decks, as far as a year in advance. Remember, the clock must be set before you can program the timer ( pg. 10 or 12). Express Timer Programming

TURN ON THE UNIT 1

Press POWER.

JVC HM-HDS1U — TURN ON THE UNIT 1 diagram (page 58)
Fig. 114

Turn on the TV and select the AV mode.

ACCESS PROGRAM SCREEN 2

Press PROG. on the remote control. The program screen appears.

PROGRAM

RECORD TO

SPEED DAIRY/WEEKLY

SOURCE

HDD SEP WEEKLY

CATV

  • If you do not set the clock, the message and the Initial Set screen will appear.
  • If you have already reserved 16 programs, the message and the program check screen will appear.
  • If you want to reset this reservation during this procedure, move the arrow to “CANCEL” by pressing @# (or 23 ), then press OK .
  • If you want to cancel this reservation, press PROG. .

START TIME STOP TIME DATE

11:30 PM 12:00 AM 06/12/01 TUE 5 CH

CONFIRM CANCEL CATEGOTY MISC.

PROG. SET PROPGRAM WITH [EXPRESS +/–, 8=DAILY, 9=WEEKLY, 7=DBS] THEN PRESS "CONFIRM"

START

STOP

DATE

CH END

SELECT THE DECK TO BE RECORDED ON 3

JVC HM-HDS1U — START diagram (page 58)
Fig. 115

Press HDD or VHS (or S-VHS).

  • If you select VHS deck, load the cassette for recording.

SET PROGRAM DATE 4

Press DATE +/–. (The current date is displayed on screen. The date you enter appears in its place.)

  • If the date of the next year appears, press DATE + .

SET PROGRAM START TIME 5

Press START +/– to enter the time you want recording to start.

  • Press and hold START +/– to move in 30-minute increments, or press and release repeatedly to move 1 minute at a time.

SET PROGRAM STOP TIME 6

Press STOP +/– to enter the time you want recording to stop.

  • Press and hold STOP +/– to move in 30-minute increments, or press and release repeatedly to move 1 minute at a time.
Show 4 more labels / short text on this page
+ – · + – · + – · + –
Page 59 of the JVC HM-HDS1U user manual — RETURN TO NORMAL SCREEN 11
Page 59 · click to enlarge
Page 59
  • NOTES:
  • To disengage the timer before recording starts, press TIMER again. Pressing once more re-engages it.
  • In case of a power failure after programming, the recorder’s memory backup keeps your selections for approximately 60 minutes.
  • Programs that start after midnight must have the next day’s date.
  • After timer recording is completed, the recorder’s power goes off automatically.
  • You can program the timer while a regular recording is in progress; the on-screen menu will not be recorded.
  • If the end of tape is reached during timer recording, the cassette is automatically ejected.
  • When timer-recording cable or satellite channels through an external tuner, be sure to keep the cable box or satellite receiver's power ON.

SET CHANNEL NUMBER 7

Press CH +/–.

  • If you are using a DBS receiver, see “ATTENTION FOR DBS RECEIVER USERS” on next page.
  • Holding down CH +/– rapidly scans through the channels.

SET TAPE SPEED 8

Press REC SPEED to set the tape speed. Each time the button is pressed, the recording speed changes as follows:

For HDD deck:

SP = LP = EP = SEP = SP = ··· For VHS deck:

SP = EP = SP = ···

ATTENTION FOR DBS RECEIVER USERS If you are using a DBS receiver (unless “DBS RECEIVER SET“ is set to “OFF” pg. 19), the BAND indication (TV or CATV or DBS) appears under the channel number display. If the channel number that has been entered requires that the band be set, “7=DBS” is displayed on the screen. Press the NUMBER key “7” to select the desired band. a– TV : To timer-record a regular TV program received

SET WEEKLY OR DAILY 9

Press WEEKLY (NUMBER “9”) for weekly serials or DAILY(M-F) (NUMBER “8”) for daily serials (Monday– Friday).

  • When WEEKLY is selected in the HDD deck recording, the recorder reserves certain space corresponding to one-program-period, then writes new data over the recorded data every week.
  • When DAILY(M-F) is selected in the HDD deck recording, the unit reserves certain space corresponding to five-programs-periods, then writes new data over the recorded data everyday (from Monday to Friday).

on the recorder. b– CATV : To timer-record a cable TV program received on

the recorder, or through a cable box (unless “CABLE BOX SET” is set to “OFF” pg.16). c– DBS : To timer-record a satellite program received

through a DBS receiver. ●If “BAND” is set to “TV” at the Tuner Set screen ( pg.13) and “CABLE BOX SET” is set to “OFF” at the Cable Box Set screen (pg. 16), CATV will not be displayed on the Program screen; If “BAND” is set to “CATV” or “CABLE BOX SET” is set to “ON”, TV will not be displayed.

SET CATEGORY 10

1. Press @# (or 23 ) to move the arrow to “CATEGORY”, then press OK . The Category Set screen appears. 2) Select the desired category by pressing @%#fi (or 253∞ ), then press OK . The Program screen resumes.

CATEGORY

CHILDRENS

CLASSICS

COMEDY DRAMA

NEWS EDUCATIONS

MOVIES

MUSIC

RELIGIOUS

SERIES

SHOPPING

SPECIAL

SOAPS

SPORTS

OTHERS

MISC.

RETURN

INDEX PROG.

RETURN TO NORMAL SCREEN 11

Move the arrow to “CONFIRM” by pressing @%#fi (or 253∞), then press OK. “PROGRAM COMPLETED” appears on the screen for a while, then normal screen appears.

  • If there is a conflict in the timer schedule and one program overlaps with another, the correction screen will appear. In this case, correct the program data. See page 61.
  • If you select VHS deck, press TIMER . The recorder turns off automatically and " ‰ " is displayed on the display panel.
Page 60 of the JVC HM-HDS1U user manual — START
Page 60 · click to enlarge
Page 60

60 EN TIMER RECORDING (cont.)

Check and Revise the Overlapped Programs

CHECK OVERLAP PROGRAM 1

JVC HM-HDS1U — 60 EN TIMER RECORDING (cont.) diagram (page 60)
Fig. 116 · 60 EN TIMER RECORDING (cont.)

Check the program to be revised, then press OK. The program screen appears.

PROGRAM CHECK

DATE START–STOP TIME CH RECORD TO SPEED 06/12/01 TUE 3:40PM–4:00PM 1CH HDD SP 06/12/01 TUE 3:40PM–4:00PM 2CH VHS SP

INDEX PROG. CHECK

CANCEL OR REVISE THE PROGRAM 2

To cancel the program, move the arrow to select “CANCEL” by pressing @%#fi (or 253∞), then press OK. To revise the program, press the appropriate button: START+/–, STOP+/–, DATE+/–, CH+/–.

PROGRAM

JVC HM-HDS1U — PROGRAM diagram (page 60)
Fig. 117

RECORD TO

SPEED DAIRY/WEEKLY

SOURCE

HDD SEP WEEKLY

CATV

START TIME STOP TIME DATE

11:30 PM 12:00 AM 06/12/01 TUE 5 CH

CONFIRM CANCEL CATEGOTY MISC.

PROG. SET PROPGRAM WITH [EXPRESS +/–, 8=DAILY, 9=WEEKLY, 7=DBS] THEN PRESS "CONFIRM"

START

STOP

DATE

CH END

RETURN TO THE NORMAL SCREEN 3

Move the arrow to “CONFIRM” by pressing @%#fi (or 253∞), then press OK. If there is no program overlap, the normal screen will appear; otherwise, the unit will show the program check screen again.

Show 4 more labels / short text on this page
+ – · + – · + – · + –
Page 61 of the JVC HM-HDS1U user manual — START
Page 61 · click to enlarge
Page 61

Check, Cancel And Revise Programs

JVC HM-HDS1U — Check, Cancel And Revise Programs diagram (page 61)
Fig. 118 · Check, Cancel And Revise Programs
JVC HM-HDS1U — Check, Cancel And Revise Programs diagram (page 61)
Fig. 119 · Check, Cancel And Revise Programs

DATE START–STOP TIME CH RECORD TO SPEED 06/12/01 TUE 3:40PM–4:00PM 1CH HDD SP 06/12/01 TUE 3:40PM–4:00PM 2CH VHS SP

JVC HM-HDS1U — Check, Cancel And Revise Programs diagram (page 61)
Fig. 120 · Check, Cancel And Revise Programs

Press %fi (or 5∞) to select the program, then press OK.

To Cancel Or Revise A Program...

CANCEL OR REVISE A PROGRAM 4

To cancel the program, move the arrow to select “CANCEL” by pressing @%#fi (or 253∞), then press OK. To revise a program, press the appropriate button: START+/–, STOP+/–, DATE+/–, CH+/–, REC SPEED, WEEKLY (NUMBER “9”), DAILY(M-F) (NUMBER “8”).

PROGRAM

RECORD TO

HDD SEP WEEKLY

SPEED DAIRY/WEEKLY

SOURCE

CATV

START TIME STOP TIME DATE

11:30 PM 12:00 AM 06/12/01 TUE 5 CH

CONFIRM CANCEL CATEGOTY MISC.

PROG. SET PROPGRAM WITH [EXPRESS +/–, 8=DAILY, 9=WEEKLY, 7=DBS] THEN PRESS "CONFIRM"

START

STOP

DATE

CH END

RETURN TO NORMAL SCREEN 5

Move the arrow to “CONFIRM” by pressing @%#fi (or 253∞), then press OK. If there is no program overlap, the normal screen will appear; otherwise, the unit will show the program check screen again.

  • If you have selected the VHS deck, press OK . The recorder turns off automatically and " ‰ " is displayed on the display panel.
Show 4 more labels / short text on this page
+ – · + – · + – · + –
Page 62 of the JVC HM-HDS1U user manual — 62 EN TIMER RECORDING (cont.)
Page 62 · click to enlarge
Page 62

62 EN TIMER RECORDING (cont.)

Auto SP → EP Timer (VHS deck only)

JVC HM-HDS1U — 62 EN TIMER RECORDING (cont.) diagram (page 62)
Fig. 121 · 62 EN TIMER RECORDING (cont.)

If, when recording in SP mode, there is not enough tape to record the entire program, the recorder automatically switches to EP mode to allow complete recording. This feature is especially handy when recording a program of more than 2 hours in length.

Make sure you set “AUTO SP→EP TIMER” to “ON” at the VHS Mode Set screen before the timer recording starts.

JVC HM-HDS1U — 62 EN TIMER RECORDING (cont.) diagram (page 62)
Fig. 122 · 62 EN TIMER RECORDING (cont.)
1. At the top of the Main Menu screen, move the arrow to “HDD/VHS SET UP” by pressing @# (or 23 ), then press fi (or ∞ ) or OK . 2) On the HDD/VHS Set Up screen, move the arrow to “VHS SET UP 2” by pressing @# (or 23 ), then press fi (or ∞ ) or OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

1. On the VHS Set Up 2 screen, move the arrow to “AUTO SP = EP TIMER” by pressing %fi (or 5∞ ), then press OK . 2) Pressing %fi (or 5∞ ) to select the desired mode, then press OK .

HDD/VHS SET UP INITIAL SET UP FUNCTION SET UP

VHS SET UP 1 VHS SET UP 2 HDD SET UP

  • NOTES:
  • If you have programmed the recorder to timer-record 2 or more programs, the second program and those thereafter may not fit on the tape if you set the Auto SP → EP Timer mode to “ON”. In this case, make sure the mode is not engaged, then set the tape speed manually during timer programming.
  • In order to ensure that the recording fits on the tape, this feature may leave a slight non-recorded section at the end of the tape.
  • There may be some noise at the point on the tape where the VCR switches from SP to EP mode.
  • The Auto SP → EP Timer feature is not available during ITR (Instant Timer Recording), and the feature will work with the following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.

For Example . . . Recording a program of 140 minutes in length onto a 120- minute tape

Show 5 more labels / short text on this page
Approximately 110 minutes · Approximately 30 minutes · SP mode · EP mode · Total 140 minutes
Page 63 of the JVC HM-HDS1U user manual — REC LINK Timer Recording (HDD deck only)
Page 63 · click to enlarge
Page 63

REC LINK enables the unit to record automatically from the external equipment with timer function. In REC LINK mode, when the signals come into the unit from the external equipment, the unit automatically turns on and starts recording on HDD deck.

REC LINK Timer Recording (HDD deck only)

JVC HM-HDS1U — REC LINK Timer Recording (HDD deck only) diagram (page 63)
Fig. 123 · REC LINK Timer Recording (HDD deck only)

After timer recording is set, turn off the external equipment connected to the unit.

Press REC LINK for about two seconds. The REC LINK button lights up.

JVC HM-HDS1U — REC LINK Timer Recording (HDD deck only) diagram (page 63)
Fig. 124 · REC LINK Timer Recording (HDD deck only)
  • While the signals are coming into the unit, the REC LINK button is blinking.
  • If you want to change the recording speed, press REC SPEED on the remote control before pressing REC LINK .

To cancel REC LINK mode, press REC LINK again.

  • NOTES:
  • You need to connect the external equipment with AUX L-1 terminals on the rear panel.
  • When the recorder is in REC LINK mode, the recorder changes the deck into VHS deck automatically. In this case, you cannot use HDD deck until the REC LINK mode is canceled.
JVC HM-HDS1U — REC LINK Timer Recording (HDD deck only) diagram (page 63)
Fig. 125 · REC LINK Timer Recording (HDD deck only)
Page 64 of the JVC HM-HDS1U user manual — SP
Page 64 · click to enlarge
Page 64

TIMER RECORDING (cont.)

This easy method lets you record (selectable in 30-min. increments) and shuts the unit off after recording is finished.

Instant Timer Recording (ITR)

JVC HM-HDS1U — Instant Timer Recording (ITR) diagram (page 64)
Fig. 126 · Instant Timer Recording (ITR)

Press REC again. " " blinks and 0:30 appears on the front display panel.

JVC HM-HDS1U — Instant Timer Recording (ITR) diagram (page 64)
Fig. 127 · Instant Timer Recording (ITR)

If you want to record for more than 30 minutes, press REC to extend the time. Each press extends recording time by 30 minutes up to 6 hours.

  • NOTES:
  • You can only perform ITR using the REC button on the recorder´s front panel.
  • After you set the ITR time, the previous display reappears.
  • To check the remaining time, press REC once during recording and the remaining time will be displayed for about 5 seconds. Be careful not to press REC again within these 5 seconds, or you will round the recording time up to the next 30 minute increment.
  • You can play a tape on one deck while using the other deck for Instant Timer Recording.

SP

VCR

Page 65 of the JVC HM-HDS1U user manual — 0:10:18 START END
Page 65 · click to enlarge
Page 65

EN 65 EDITING

About Hybrid Navigation

The display for modification or deletion

HDD NAVI

SCAN EDITING EASY DUBBING

TOTAL TIME 0H00M REMAIN TIME 11H07M (SP)

In the Simple Operations section, it is briefly described how to search for the beginning of each recorded program using the Navigation functions, but more detailed explanations are provided in this section using HDD Navigation by way of example.

06/12/01 TUE 06/12/01 TUE 06/12/01 MON 06/12/01 TUE

[MISC.]

06/12/01 TUE 10:30AM – 12:55PM 2CH SP 145min

This recorder has a built-in Hybrid Navigation system, which consists of two Navigation system: HDD Navigation and VHS Navigation. Using Navigation system, you can easily modify registered information or edit the program when dubbing from the HDD deck to VHS deck, as well as search for the beginning of each program.

PLAY MODIFY DELETE CANCEL

INDEX

About Registration of Information The following information is automatically registered for each program when ordinary recording or timer recording is performed (for the VHS deck, when “NAVIGATION” is set to “ON” in the “VHS SET UP 1” of the main MENU), then stored in an area specified on the hard disk.

The display for EASY DUBBING

SCAN EDITING EASY DUBING HDD NAVI

TOTAL TIME 0H00M REMAIN TIME 11H07M (SP)

  • index*: reduced still pictures to show program titles
  • program title*
  • category*
  • date and time
  • channel
  • recording speed
  • length of recording time The items marked with an asterisk (*) can be easily modified and registered again after recording by using Navigation system.

06/12/01 TUE 06/12/01 TUE 06/11/01 MON 06/10/01 MON

[MISC.]

06/12/01 TUE 10:30AM – 12:55PM 2CH SP 145min

DUB START DUB/DEL CANCEL

INDEX

SELECT WITH [∞523] AND [MEMORY] THEN PRESS [OK]

About Editing of Programs Navigation system has three functions for editing of programs: modification or deletion of information, dubbing easily from HDD deck to VHS deck, and random assemble editing. In the following section, those functions are mentioned.

The display for EDITING

The Limitations of Registration You can register information up to 60 programs in HDD Navigation. In VHS Navigation, you can register information up to 2000 programs or up to 680 cassettes. To register the information on VHS Navigation, you need record a program for more than 5 minutes in SP mode (for more than 15 minutes in EP mode). When the amount of information is at the limits of registration, you cannot record new program any more. In this case, you need to delete old programs to register new one.

HDD NAVI

R.A.EDIT

1 0:05:10 TO 0:06:37 2 0:01:42 TO 0:02:53 3 0:10:18 TO –:––:–– 4 –:––:–– TO –:––:–– 5 –:––:–– TO –:––:–– 6 –:––:–– TO –:––:–– 7 –:––:–– TO –:––:–– 8 –:––:–– TO –:––:––

0:10:18 START END

IN / OUT

MODIFY EDIT START RETURN TOTAL 0:01:50

NAVI INDEX

SEARCH IN/OUT POINT WITH [PLAY/ FF/REW/PAUSE] THEN PRESS "IN/OUT"

– / 6 · – / 6

Page 66 of the JVC HM-HDS1U user manual — TURN ON THE RECORDER 1
Page 66 · click to enlarge
Page 66

66 EN EDITING (cont.)

SELECT DECK 2

Modify Information

Press HDD or VHS (or S-VHS).

G When you select the VHS deck, load the cassette you

want to edit.

ACCESS NAVIGATION SCREEN 3

JVC HM-HDS1U — ACCESS NAVIGATION SCREEN 3 diagram (page 66)
Fig. 128

Press NAVI. The Navigation screen corresponding to the selected deck appears.

G For VHS deck, when “NAVIGATION” is set to “OFF”,

the Navigation screen does not appear.

SELECT PROGRAM 4

Press @%#fi (or 253∞) to move the arrow to select one program you want to modify, then press fi (or ∞) or OK.

ACCESS MODIFY SCREEN 5

JVC HM-HDS1U — ACCESS MODIFY SCREEN 5 diagram (page 66)
Fig. 129
1. Press @# (or 23 ) to move the arrow to “MODIFY”, then press fi (or ∞ ) or OK . 2) Press @# (or 23 ) to move the arrow to “MODIFY INDEX”, then press OK . The arrow moves to “REPLACE”.

REGISTER NEW INDEX 6

1. Search for the picture from the program by pressing the appropriate buttons: PLAY , FF , REW , or PAUSE . The pictures of the program appear on the left window. 2) Confirm the arrow is on “REPLACE”, then press OK to register new index. New index appears on the right window.

HDD NAVI

MODIFY INDEX MODIFY TITLE MODIFY CATEGORY

REPLACE

0:10:30 0:10:30 START END

06/12/01 TUE 12:25AM – 12:55PM 2CH SP 30min [MISC.]

RETURN

NAVI INDEX

G When you press OK with the arrow on “RETURN”

you can return the previous screen.

RETURN TO NORMAL SCREEN 7

Press NAVI.

G When you select VHS deck, press STOP to cancel

PAUSE after pressing NAVI.

Modify Index

The Navigation systems cannot work while the recorder is recording on the HDD deck or in REC LINK mode.

TURN ON THE RECORDER 1

Press POWER.

Page 67 of the JVC HM-HDS1U user manual — RETURN TO NORMAL SCREEN 8
Page 67 · click to enlarge
Page 67

Modify Program Title

ACCESS NAVIGATION SCREEN 3

The Navigation systems cannot work while the recorder is recording on the HDD deck or in REC LINK mode.

Press NAVI. The Navigation screen corresponding to the selected deck appears.

G For VHS deck, when “NAVIGATION” is set to “OFF”,

the Navigation screen does not appear. SELECT PROGRAM 4

JVC HM-HDS1U — the Navigation screen does not appear. SELECT PROGRAM 4 diagram (page 67)
Fig. 130 · the Navigation screen does not appear. SELECT PROGRA…

Press @%#fi (or 253∞) to move the arrow to select one program you want to modify, then press fi (or ∞) or OK.

ACCESS MODIFY SCREEN 5

1. Press @# (or 23 ) to move the arrow to “MODIFY”, then press fi (or ∞ ) or OK . 2) Press @# (or 23 ) to move the arrow to “MODIFY TITLE”, then press OK . The Modify Title screen appears.

ENTER NEW TITLE 6

JVC HM-HDS1U — ENTER NEW TITLE 6 diagram (page 67)
Fig. 131

Press @%#fi (or 253∞) to move the arrow to the desired letter or command, then OK. Repeat this process to complete the title.

HDD NAVI

MODIFY INDEX MODIFY TITLE MODIFY CATEGORY

A B C D E F G H I 1 2 3 : – + J K L M N O P Q R 4 5 6 • / * S T U V W X Y Z 7 8 9 0 [ ]

ENTER DELETE < > DELETE ALL

06/12/01 TUE 12:25AM – 12:55PM 2CH SP 30min [MISC.]

G To correct a letter,

RETURN

NAVI INDEX

press CLEAR on the remote control.

G You can enter the letters up to 15.

G You can enter the new title from the remote control.

For example, when you press 2 repeatedly, “A”,“B”,“C”,“2”,“A” appears by turns. You can use the following buttons.

1, 2, 3, 4, 5, 6, 7, 8, 9, 0: for entering letters, numbers, marks (–, +, *) and blank <, >: for moving the entering or inserting point

REGISTER NEW TITLE 7

Press @%#fi (or 253∞) to move the arrow to “RETURN”, then press OK. The Navigation screen appears again.

RETURN TO NORMAL SCREEN 8

Press NAVI.

JVC HM-HDS1U — RETURN TO NORMAL SCREEN 8 diagram (page 67)
Fig. 132
Page 68 of the JVC HM-HDS1U user manual — RETURN TO NORMAL SCREEN 8
Page 68 · click to enlarge
Page 68

68 EN EDITING (cont.)

Modify Category

TURN ON THE RECORDER 1

The Navigation systems cannot work while the recorder is recording on the HDD deck or in REC LINK mode.

Press POWER.

SELECT DECK 2

JVC HM-HDS1U — SELECT DECK 2 diagram (page 68)
Fig. 133

Press HDD or VHS (or S-VHS). The Navigation screen corresponding to the selected deck appears.

ACCESS NAVIGATION SCREEN 3

Press NAVI. The Navigation screen corresponding to the selected deck appears.

  • For VHS deck, when “NAVIGATION” is set to “OFF”, the Navigation screen does not appear.

SELECT PROGRAM 4

Press @%#fi (or 253∞) to move the arrow to select one program you want to modify, then press fi (or ∞) or OK.

ACCESS MODIFY SCREEN 5

1. Press @# (or 23 ) to move the arrow to “MODIFY”, then press fi (or ∞ ) or OK . 2) Press @# (or 23 ) to move the arrow to “MODIFY CATEGORY”, then press OK . The Modify Category screen appears.
JVC HM-HDS1U — ACCESS MODIFY SCREEN 5 diagram (page 68)
Fig. 134

SELECT NEW CATEGORY 6

Press @%#fi (or 253∞) to move the arrow to the new category, then press OK.

HDD NAVI

MODIFY INDEX MODIFY TITLE MODIFY CATEGORY

CHILDRENS

CLASSICS

COMEDY

DRAMA

NEWS EDUCATIONS

MOVIES

MUSIC

RELIGIOUS

SERIES

SHOPPING

SPECIAL

SOAPS

SPORTS

OTHERS

MISC.

06/12/01 TUE 12:25AM – 12:55PM 2CH SP 30min [MISC.]

RETURN

NAVI INDEX

REGISTER NEW CATEGORY 7

Press @%#fi (or 253∞) to move the arrow to “RETURN”, then OK. The Navigation screen appears again.

RETURN TO NORMAL SCREEN 8

Press NAVI.

Page 69 of the JVC HM-HDS1U user manual — RETURN TO NORMAL SCREEN 7
Page 69 · click to enlarge
Page 69

Delete Information The Navigation systems cannot work while the recorder is recording on the HDD deck or in REC LINK mode.

TURN ON THE RECORDER 1

Press POWER.

JVC HM-HDS1U — TURN ON THE RECORDER 1 diagram (page 69)
Fig. 135

For HDD Navigation: When you delete the registered information of a program, the recorder delete the program itself on the hard disk drive. The deleted program is never resumed. For VHS Navigation: When you delete the registered information of a program, the recorder delete only the information on the hard disk drive. The program itself cannot be deleted with VHS Navigation.

SELECT DECK 2

Press HDD or VHS (or S-VHS). The indicator corre- sponding to the selected deck lights up.

ACCESS NAVIGATION SCREEN 3

Press NAVI. The Navigation screen corresponding to the selected deck appears.

JVC HM-HDS1U — ACCESS NAVIGATION SCREEN 3 diagram (page 69)
Fig. 136
  • For VHS deck, when “NAVIGATION” is set to “OFF”, the Navigation screen does not appear.

SELECT PROGRAM 4

Press @%#fi (or 253∞) to move the arrow to select one program whose information you want to delete, then press fi (or ∞) or OK.

  • For VHS deck, you can delete all the information of a cassette at the “CASSETTE #”.

ACCESS DELETE SCREEN 5

Press @# (or 23) to move the arrow to “DELETE”, then press OK. The message appears for your confirma- tion.

JVC HM-HDS1U — ACCESS DELETE SCREEN 5 diagram (page 69)
Fig. 137

CONFIRM DELETION 6

Press @# (or 23) to select “DELETE”, then press OK.

  • When you cancel the deletion, select “CANCEL”, then press OK .

RETURN TO NORMAL SCREEN 7

Press NAVI.

Page 70 of the JVC HM-HDS1U user manual — SELECT DUBBING OPTION 5
Page 70 · click to enlarge
Page 70

70 EN EDITING (cont.)

Dubbing

Easy Dubbing from HDD deck to VHS deck

Because this recorder includes both HDD deck and VHS deck, you can easily use it for dubbing without connecting any other equipment.

TURN ON THE RECORDER 1

JVC HM-HDS1U — TURN ON THE RECORDER 1 diagram (page 70)
Fig. 138

Press POWER.

ACCESS HDD NAVIGATION SCREEN 2

Press HDD, then press NAVI. The HDD Navigation appears.

ACCESS EASY DUBBING SCREEN 3

Press @# (or 23) to move the arrow to “EASY DUBBING”, then press OK. The Easy Dubbing screen appears.

JVC HM-HDS1U — ACCESS EASY DUBBING SCREEN 3 diagram (page 70)
Fig. 139

SELECT PROGRAM(S) 4

Press @# (or 23) to move the arrow to the desired program, then press OK.

SCAN EDITING EASY DUBING HDD NAVI

TOTAL TIME 0H00M REMAIN TIME 11H07M (SP)

G When you want to

select the plural programs, press MEMORY on the remote control after selecting the desired program. The numbers of the playback order appear on the index. You can select up to 8 programs.

06/12/01 TUE 06/12/01 TUE 06/11/01 MON 06/10/01 MON

06/12/01 TUE 10:30AM – 12:55PM 2CH SP 145min

[MISC.]

DUB START DUB/DEL CANCEL

INDEX

SELECT WITH [∞523] AND [MEMORY] THEN PRESS [OK]

G When you want to correct the order, after moving the

arrow on the numbered index, press MEMORY on the remote control, or move arrow to “CANCEL” by pressing @%#fi (or 253∞), then press OK. The number disappears and the recorder re-numbers the other programs automatically.

SELECT DUBBING OPTION 5

Press @%#fi (or 253∞) to move the arrow to select “DUB START” or “DUB/DEL”, then press OK. The message for preparing a cassette appears.

  • When “DUB START” is selected, the programs remains on the hard disk after dubbing.
  • When “DUB/DEL” is selected, the unit delete the programs on the hard disk after dubbing automatically.

– / 6

Page 71 of the JVC HM-HDS1U user manual — EDITING
Page 71 · click to enlarge
Page 71
JVC HM-HDS1U — EDITING diagram (page 71)
Fig. 140
JVC HM-HDS1U — EDITING diagram (page 71)
Fig. 141
1. Search the point where you want to start dubbing by pressing PLAY , FF , REW , then press STOP . 2) Press REC and PAUSE simultaneously to enter the Record-Pause mode.

Press HDD. The screen in step 5 appears again.

JVC HM-HDS1U — EDITING diagram (page 71)
Fig. 142

Press @# (or 23) to move the arrow to “DUB START”, then press OK. When the dubbing completes success- fully, the message “DUBBING COMPLETES” appears on the screen.

G To cancel dubbing, select “CANCEL” in above step.

Once the dubbing is stopped, it can be not resumed. In this case, the message appears on the screen, and the programs on the hard disk drive are not deleted even though “DUB/DEL” is selected.

Page 72 of the JVC HM-HDS1U user manual — NOTES:
Page 72 · click to enlarge
Page 72

72 EN EDITING (cont.)

You can dub selected scenes on a tape, starting and stopping wherever you wish.

Normal Dubbing (from HDD to VHS)

TURN ON THE RECORDER 1

Press POWER.

PREPARE HDD DECK FOR DUBBING 2

1. Press HDD and select the program to be dubbed. You can select the program by HDD Navigation. 2) Press CH +/– to set the channel other than “DUB”.
JVC HM-HDS1U — PREPARE HDD DECK FOR DUBBING 2 diagram (page 72)
Fig. 143

LOCATE START POINT 3

1. Select the point where you want to start dubbing by pressing PLAY , FF , REW . 2) Press REW a little, then press PLAY to start playback. 3) Press PAUSE to pause playback before that point a little.

PREPARE VHS DECK FOR DUBBING 4

1. Press VHS (or S-VHS ) and load a recordable cassette. 2) Press CH +/– to set the channel “DUB”. 3) Press REC SPEED to select recording speed. 4) Select the point where you want to start recording by pressing PLAY , FF , REW , STOP .
JVC HM-HDS1U — PREPARE VHS DECK FOR DUBBING 4 diagram (page 72)
Fig. 144

START DUBBING 5

1. Press HDD and PLAY to start playback. 2) Press VHS and REC ( REC and PLAY on the remote control) to start dubbing.

END DUBBING 6

Press STOP. Then press HDD and press STOP.

NOTES:

G There may be a discrepancy of several seconds between

where you intend editing to start, and where it actually starts.

G The superimposed indication during the operation or dubbing

is not recorded.

Page 73 of the JVC HM-HDS1U user manual — NOTES:
Page 73 · click to enlarge
Page 73

You can dub selected scenes on a tape, starting and stopping wherever you wish.

Normal Dubbing (from VHS to HDD)

TURN ON THE RECORDER 1

Press POWER.

PREPARE VHS DECK FOR DUBBING 2

1. Press VHS (or S-VHS ) and select the program to be dubbed. You can select the program by VHS Navigation. 2) Press CH +/– to set the channel other than “DUB”.
JVC HM-HDS1U — PREPARE VHS DECK FOR DUBBING 2 diagram (page 73)
Fig. 145

LOCATE START POINT 3

1. Select the point where you want to start dubbing by pressing PLAY , FF , REW . 2) Press REW a little ,then PLAY to start playback. 3) Press PAUSE to pause playback before that point a little.

PREPARE HDD DECK FOR DUBBING 4

1. Press HDD . 2) Press CH +/– to set the channel “DUB”. 3) Press REC SPEED to select recording speed. 4) Select the point where you want to start recording by pressing PLAY , FF , REW , STOP .
JVC HM-HDS1U — PREPARE HDD DECK FOR DUBBING 4 diagram (page 73)
Fig. 146
  • Set “PICTURE CONTROL” to “EDIT” at the “VHS SET UP 1” of the Main Menu ( pg. 44).

START DUBBING 5

1. Press VHS and PLAY to start playback. 2) Press HDD and REC ( REC and PLAY on the remote control) to start dubbing.

G To enter recording pause, press and hold REC and

press PAUSE on the remote control. To resume recording, press and hold REC and press PLAY on the remote control.

END DUBBING 6

Press STOP. Then press VHS and press STOP.

G Set “PICTURE CONTROL” to “AUTO” or “STAN-

DARD” at the “VHS SET UP 1” of the main MENU after dubbing.

NOTES:

G There may be a discrepancy of several seconds between

where you intend editing to start, and where it actually starts.

G The superimposed indication during the operation or dubbing

is not recorded.

G For HDD deck, the recording pause takes effect only when

the recorder is recording on the HDD deck with the channel set to “L-1”, “F-1”, or “DUB”. The recording pause is released in 5 minutes automatically. Picture and sound may be disturted at the point where the recording pause is released.

G Dubbing copyright guarded tape is not possible.

Page 74 of the JVC HM-HDS1U user manual — 0:10:18 START END
Page 74 · click to enlarge
Page 74

74 EN EDITING (cont.)

8-program Editing Memory (1 program x 8 scenes) By using the Random Assemble Editing function, you can select up to 8 scenes from a previously recorded program on the HDD deck and automatically dub them onto a VHS cassette. Random Assemble Editing is possible only when dubbing from the HDD deck to the VHS deck. Random Assemble Editing TURN ON THE UNIT 1

Press POWER.

JVC HM-HDS1U — 74 EN EDITING (cont.) diagram (page 74)
Fig. 147 · 74 EN EDITING (cont.)

SELECT HDD DECK 2

Press HDD.

ACCESS HDD NAVIGATION SCREEN 3

Press NAVI. The HDD Navigation screen appears.

ACCESS EDIT SCREEN 4

Press @# (or 23) to move the arrow to “EDITING”, then press fi (or ∞) or OK.

JVC HM-HDS1U — ACCESS EDIT SCREEN 4 diagram (page 74)
Fig. 148

SELECT PROGRAM 5

Press @# (or 23) to move the arrow to one program you want to edit, then press fi (or ∞) or OK.

ACCESS R.A. EDIT SCREEN 6

Press OK at the “R.A. EDIT”. The R.A.Edit screen appears.

START PROGRAM 7

Press PLAY to start playback. The playback pictures appear in the window of the R.A.Edit screen. The first edit-in time starts counting with the arrow to “IN/OUT”.

  • You can search the scene by using the following buttons: PLAY , PAUSE , FF , REW .

SELECT EDIT-IN AND EDIT-OUT POINTS 8

1. Find the point where you want the edited scene to begin, then press OK with the arrow to “IN/OUT”. The edit-in time is fixed and the edit-out time starts counting. 2) Find the point where you want the edited scene to end, then press OK with the arrow to “IN/ OUT”. The edit-out time is fixed and the next editout time starts counting. You can repeat this up to 8 times.

HDD NAVI

R.A.EDIT

1 0:05:10 TO 0:06:37 2 0:01:42 TO 0:02:53 3 0:10:18 TO –:––:–– 4 –:––:–– TO –:––:–– 5 –:––:–– TO –:––:–– 6 –:––:–– TO –:––:–– 7 –:––:–– TO –:––:–– 8 –:––:–– TO –:––:––

0:10:18 START END

IN / OUT

MODIFY EDIT START RETURN TOTAL 0:01:50

NAVI INDEX

SEARCH IN/OUT POINT WITH [PLAY/ FF/REW/PAUSE] THEN PRESS "IN/OUT"

Page 75 of the JVC HM-HDS1U user manual — STOP EDITING 15
Page 75 · click to enlarge
Page 75

SELECT THE OTHER EDIT-IN AND EDIT-OUT POINTS 9

Repeat step 8. You can select up to 8 pairs of edit-in and edit-out points.

  • To modify the points 1) Move the arrow to “MODIFY”, then press OK. 2) Select the desired points by pressing @%#fi (or 253∞ ), then press OK . The selected point starts couting. 3) Repeat step 8 .

ACCESS START EDITING SCREEN 10

JVC HM-HDS1U — ACCESS START EDITING SCREEN 10 diagram (page 75)
Fig. 149

Press @%#fi (or 253∞) to move the arrow to “EDIT START”, then press OK. The Start Editing screen with message appear.

PREPARE VHS DECK FOR RECORDING 11

1. Press VHS (or S-VHS ). 2) Load a recordable cassette. And, find the point where you want to start recording by pressing PLAY , FF , REW . 3) Press PAUSE and REC to enter the Record-Pause mode.

ACCESS START EDITING SCREEN 12

Press HDD. The Start Editing screen with message appear again.

JVC HM-HDS1U — ACCESS START EDITING SCREEN 12 diagram (page 75)
Fig. 150

START EDITING 13

Press @%#fi (or 253∞), to move the arrow to “OK”, then press OK. The editing starts. The message “EDIT COMPLETED” appears when the editing is complete successfully.

RETURN TO R.A. EDIT SCREEN 14

Press OK.

  • If you want to continue to edit, start from step 7.

STOP EDITING 15

Press NAVI. The VHS deck stops recording and enters the Record-Pause mode. Press VHS (or S-VHS), then press STOP.

Page 76 of the JVC HM-HDS1U user manual — S-VIDEO OUT
Page 76 · click to enlarge
Page 76

EDITING (cont.)

You can use a camcorder as the player and your recorder as the recorder.

Edit From A Camcorder

MAKE CONNECTIONS 1

Connect an AV cable between the camcorder’s VIDEO OUT and AUDIO OUT connectors and your recorder’s VIDEO IN and AUDIO IN connectors.

  • If connecting a camcorder with an S-VIDEO output connector, it is recommended to use the S-VIDEO connection to minimize picture degradation while editing.
  • VHS deck ONLY When a Master Edit Control-equipped JVC camcorder is used, the camcorder is capable of controlling your recorder. The mini-plug cable is a mono 3.5 mm mini-plug to mono 3.5 mm mini-plug connector.
  • If connecting to a camcorder with a monaural output, connect the audio output connector on the camcorder to AUDIO IN L of the recorder.

VIDEO IN

JVC HM-HDS1U — VIDEO IN diagram (page 76)
Fig. 151

TURN ON THE RECORDER 2

Press POWER.

SELECT RECORDING DECK 3

Press HDD or VHS (or S-VHS).

  • When you select VHS deck, load a recordable cassette.

SELECT INPUT MODE 4

Press CH +/– to select depending on the connector being used – “F-1” for the front panel input connectors, or “L-1” for the rear panel input connectors.

ACCESS VIDEO INPUTS SCREEN 5

1. Press MENU . 2) Select “FUNCTION SET UP”, then press %fi (or 5∞ ) or OK . 3) Select “VIDEO INPUTS”, then press %fi (or 5∞ ) or OK .

EDIT

(not supplied) (JVC camcorder only)

S-VIDEO OUT

SELECT VIDEO INPUT MODE 6

Set ”S-VIDEO” or ”COMPOSITE” to “FRONT AUX F-1” or “REAR AUX L-1” by pressing %fi (or 5∞) or OK. For details on setting, see page 22.

PAUSE connector · Mini-plug cable

Page 77 of the JVC HM-HDS1U user manual — NOTES:
Page 77 · click to enlarge
Page 77
JVC HM-HDS1U — EDITING diagram (page 77)
Fig. 152
JVC HM-HDS1U — EDITING diagram (page 77)
Fig. 153
  • VHS deck ONLY If you are using a Master Edit Control-equipped JVC camcorder, it can put the recorder automatically into Record mode. (Refer to camcorder's instruction manual.)
  • For HDD deck
JVC HM-HDS1U — EDITING diagram (page 77)
Fig. 154

To enter recording pause, press and hold REC and press PAUSE on the remote control. To resume recording, press and hold REC and press PLAY on the remote control.

NOTES:

G If you use an auxiliary input to connect a cable box or DBS

receiver, make sure that the correct AUX INPUT (“COMPOSITE” or “S-VIDEO”) is selected after you have finished editing ( steps 5 – 7).

G For HDD deck, the recording pause takes effect only when

the recorder is recording on the HDD deck with the channel set to “L-1”, “F-1”, or “DUB”. The recording pause is released in 5 minutes automatically. Picture and sound may be disturted at the point where the recording pause is released.

G Dubbing copyright guarded tape is not possible.

Page 78 of the JVC HM-HDS1U user manual — VIDEO IN
Page 78 · click to enlarge
Page 78

EDITING (cont.)

You can use your recorder as the player or the recorder.

Edit To Or From Another VCR

JVC HM-HDS1U — Edit To Or From Another VCR diagram (page 78)
Fig. 155 · Edit To Or From Another VCR

Connect an AV cable between the player’s VIDEO OUT and AUDIO OUT connectors and the recorder’s VIDEO IN and AUDIO IN connectors.

  • If using another VCR with an S-VIDEO input or output connector, it is recommended to use the SVIDEO connection to minimize picture degradation while editing.
  • When using your recorder as the recorder and a monaural VCR as the player, connect the player’s AUDIO OUT connector to the AUDIO IN L connector on the recorder.

VIDEO OUT

AUDIO OUT

JVC HM-HDS1U — VIDEO OUT diagram (page 78)
Fig. 156

Insert the playback cassette into the player and the cassette to be recorded on into the recorder.

  • Advantages Of S-VHS Editing S-VHS allows you make high resolution video recordings when dubbing from one VCR to another. You can edit from VHS to S-VHS, from S-VHS to VHS, or from S-VHS to S-VHS.
  • From VHS to S-VHS: Record VHS playback signals in the SVHS mode. Although the picture quality is inherently limited by the original VHS source material, the edited tape has better picture quality than those made by VHS-to-VHS editing.
  • From S-VHS to VHS: Because the picture quality of the source material is very high, the edited tape has better picture quality than those made by VHS-to-VHS editing.
  • From S-VHS to S-VHS: A high resolution copy is made of a high resolution original S-VHS tape with minimal picture degradation. This is the preferred method of video dubbing.

VIDEO IN

JVC HM-HDS1U — VIDEO IN diagram (page 78)
Fig. 157
JVC HM-HDS1U — VIDEO IN diagram (page 78)
Fig. 158
Page 79 of the JVC HM-HDS1U user manual — START RECORDER 7
Page 79 · click to enlarge
Page 79

SET RECORDER’S INPUT MODE 4

JVC HM-HDS1U — SET RECORDER’S INPUT MODE 4 diagram (page 79)
Fig. 159

Press CH +/– to select depending on the connector being used – “L-1” for the front panel input connectors, or “R-1” for the rear panel input connectors. NOTE: If you use your recorder as the recorder and have connected another VCR to your recorder´s S-VIDEO IN connector, you need to set “REAR AUX INPUT” to “S- VIDEO” at the Mode Set screen. Follow steps 5 – 7 from the “Edit From A Camcorder” section ( pg. 76 and 77).

SELECT “EDIT” FOR PICTURE CONTROL SET MODE (VHS DECK ONLY) 5

JVC HM-HDS1U — SELECT “EDIT” FOR PICTURE CONTROL SET MODE (VHS DECK ONLY) 5 diagram (page 79)
Fig. 160

Follow the “Picture Control” section on page 44, then select “EDIT.” NOTE: When you select “EDIT” to dub tapes, be sure to select “AUTO” or (“NORM” when “VIDEO CALIBRATION” is set to “OFF”) after you finish dubbing the tapes.

START PLAYER 6

Set to its play mode. NOTE: If the player is equipped with a superimpose/OSD disable feature then set “SUPERIMPOSE” to “OFF” before pressing PLAY ( pg. 28 for HDD deck, pg. 41 for VHS deck).

START RECORDER 7

Set to its record mode.

Page 80 of the JVC HM-HDS1U user manual — ENGAGE AUDIO DUBBING 5
Page 80 · click to enlarge
Page 80

EDITING (cont.)

VHS Audio Dubbing Audio dubbing replaces the normal audio sound of a previously recorded tape with a new soundtrack. Use your recorder as the recorder. Audio Dubbing (VHS deck only)

JVC HM-HDS1U — EDITING (cont.) diagram (page 80)
Fig. 161 · EDITING (cont.)
JVC HM-HDS1U — EDITING (cont.) diagram (page 80)
Fig. 162 · EDITING (cont.)

MAKE CONNECTIONS 1

Connect an audio component to the AUDIO IN L + R connectors on the recorder´s front panel. *When connecting monaural equipment, use only the recorder´s AUDIO IN L connector. SELECT VHS DECK 2

Press VHS (or S-VHS).

SET INPUT MODE 3

Press CH +/– to select depending on the connector being used – “F-1” for the front panel input connectors, or “L-1” for the rear panel input connectors.

LOCATE START POINT 4

Press PLAY to start playback of the tape in your recorder, and press PAUSE when you find the point where you want to start dubbing.

  • Press C.RESET to change the counter display to “0:00:00”.

ENGAGE AUDIO DUBBING 5

Press A. DUB.

  • Your recorder enters the Audio Dubbing Pause mode. ( blinks, and light up on the front display panel.)

Audio-dubbed tape

Page 81 of the JVC HM-HDS1U user manual — EDITING
Page 81 · click to enlarge
Page 81
JVC HM-HDS1U — EDITING diagram (page 81)
Fig. 163
JVC HM-HDS1U — EDITING diagram (page 81)
Fig. 164

Engage the audio component´s Play mode, then press PLAY to start the tape in your recorder. Audio dubbing begins at this point.

  • blinks and is displayed on the front display panel.
  • To stop dubbing temporarily, press PAUSE . Press PLAY to resume dubbing. END AUDIO DUBBING 7

Press STOP to stop the tape in your recorder, and engage the audio component's Stop mode.

  • NOTES:
  • When monitoring the sound during Audio Dubbing, the normal soundtrack is automatically selected. If you wish to hear the Hi-Fi or mixed sound (Hi-Fi + Normal soundtracks), refer to the “Select The Soundtrack” section ( pg. 46) and select the soundtrack you wish to hear.
  • Audio dubbing stops automatically when the counter reaches “0:00:00”, and the recorder enters the Play mode. Check the counter reading before dubbing.
  • Audio dubbing is also possible using the rear AUDIO IN connectors.
  • Audio dubbing cannot be performed on a VHS/S-VHS cassette that has had its record safety tab removed.
  • When playing back an audio-dubbed tape, refer to the “Select The Soundtrack” section ( pg. 46) to select the soundtrack you wish to hear.
  • Picture may be distorted during Audio Dubbing Pause.
  • It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.
JVC HM-HDS1U — EDITING diagram (page 81)
Fig. 165
Page 82 of the JVC HM-HDS1U user manual — SET TV BRAND CODE 3
Page 82 · click to enlarge
Page 82

82 EN SPECIAL FEATURES

TV Multi-Brand Remote Control

The recorder´s remote control can control several functions on JVC remote control TVs and on the brands of remote control TVs listed below.

JVC HM-HDS1U — 82 EN SPECIAL FEATURES diagram (page 82)
Fig. 166

TURN ON THE TV 1

Turn the power on using the TV´s remote control.

SET REMOTE CONTROL MODE 2

Press TV on the remote control when “TV” appears on the display window of the recorder’s remote control.

SET TV BRAND CODE 3

Enter your TV’s brand code using the NUMBER keys, then press OK. Follow the example shown at bottom left.

  • Once you have set the remote control to operate the TV, you don’t have to repeat this step until you replace your remote control’s batteries.
  • PANASONIC has two codes. If the TV does not function with one code, try entering the other. OPERATE TV 4

First, press POWER on the remote to see if the TV’s power goes off as it should. If it does, try other operations.

  • The POWER , TV/VCR , TV CH +/– , TV VOL +/– , A. MONITOR (TV Muting) and NUMBER keys on the remote can all be used to operate the TV. *For some brands of TV, you must press ENTER after having pressed the NUMBER keys.
  • To return the remote to the recorder control, press HDD or VHS (or S-VHS ).
JVC HM-HDS1U — SET TV BRAND CODE 3 diagram (page 82)
Fig. 167
Page 83 of the JVC HM-HDS1U user manual — CABLE BOX BRAND NAME BRAND CODE
Page 83 · click to enlarge
Page 83

Cable Box Multi-Brand Remote Control

JVC HM-HDS1U — Cable Box Multi-Brand Remote Control diagram (page 83)
Fig. 168 · Cable Box Multi-Brand Remote Control

The recorder’s remote control can control functions on the brands of cable boxes listed below. Some cable box brands have more than one code. If your cable box does not function with a specified code, try other codes.

TURN ON THE CABLE BOX 1

Turn the power on using the cable box’s remote control.

SET REMOTE CONTROL MODE 2

Press TV on the remote control when “CABLE DBS” appears on the display window of the recorder’s remote control.

ENTER CABLE BOX BRAND 3

Enter your cable box brand code using the NUMBER keys, then press OK. Follow the example shown at bottom left.

  • Once you have set the remote control to operate the cable box, you don't have to repeat this step until you replace the remote control's batteries. OPERATE CABLE BOX 4

First, press POWER to see if the cable box’s power goes off as it should. If it does, try other functions (TV CH +/– and the NUMBER keys can be used to operate the cable box).

CABLE BOX BRAND NAME BRAND CODE

ARCHER 01, 05, 17 CABLETENNA 01, 17 CABLEVIEW 15, 16, 17, 21, 25 CITIZEN 15, 16, 17, 21, 25 CURTIS 02, 08 DIAMOND 01, 17 EASTERN 19 GC BRAND 15, 16, 17, 21, 25 GEMINI 15 GENERAL INSTRUMENTS 01, 04, 06, 11, 12, 15 HAMLIN 10, 18, 19, 23 JASCO 15 JERROLD 01, 04, 06, 11, 12, 15 NOVAVISION 02, 08 OAK 07, 20 PANASONIC 13, 14 PULSER 15, 16, 17, 21, 25 RCA 13, 14 REGAL 10, 18, 19, 23 REGENCY 19 REMBRANDT 01, 16, 17 SAMSUNG 05, 16, 24 SCIENTIFIC ATLANTA 02, 08 SIGMA 07, 20 SL MARX 05, 16, 17, 24, 25 SPRUCER 13, 14 STARGATE 05, 15, 16, 17, 21, 24, 25 TELEVIEW 05, 16, 24 TOCOM 01, 04, 16 UNIKA 01, 17 UNIVERSAL 16, 17, 25 VIDEOWAY 03, 09, 22 ZENITH 03, 09, 22

  • For some brands of cable box, you must press ENTER after having pressed the NUMBER keys.
  • To return the remote to the recorder control, press HDD or VHS (or S-VHS ).
  • NOTES:
  • You must set the cable box brand for your remote control and the cable box brand for your Controller ( pg. 16) separately. The list of cable box brands that can be controlled by your remote control is different from the list of brands that can be controlled by your controller.
  • Depending on the type of cable box, there may be cases where some or all functions cannot be operated using the remote control.
  • It's not possible to set the remote control for both your cable box and a DBS receiver at the same time. You can only set the remote control to operate one of these units at a time.
Page 84 of the JVC HM-HDS1U user manual — OPERATE DBS RECEIVER 4
Page 84 · click to enlarge
Page 84

SPECIAL FEATURES (cont.)

DBS Receiver Multi-Brand Remote Control

The recorder´s remote control can control functions on the brands of DBS (Direct Broadcast Satellite) receivers listed below.

JVC HM-HDS1U — SPECIAL FEATURES (cont.) diagram (page 84)
Fig. 169 · SPECIAL FEATURES (cont.)

TURN ON THE DBS RECEIVER 1

Turn the power on using the DBS receiver’s remote control.

SET REMOTE CONTROL MODE 2

Press TV on the remote control when “CABLE DBS” appears on the display window of the recorder’s remote control.

ENTER DBS RECEIVER BRAND 3

Enter your cable box brand code using the NUMBER keys, then press OK. Follow the example shown at bottom left.

  • Once you have set the remote control to operate the DBS receiver, you don´t have to repeat this step until you replace the remote control´s batteries.

OPERATE DBS RECEIVER 4

First, press POWER to see if the DBS receiver’s power goes off as it should. If it does, try other functions (TV CH +/– and the NUMBER keys can be used to operate the DBS receiver).

  • For some brands of DBS receiver, you must press ENTER after having pressed the NUMBER keys.
  • To return the remote to the recorder control, press HDD or VHS (or S-VHS ).
  • NOTES:
  • You must set the DBS receiver brand for your remote control and the DBS receiver brand for your Controller ( pg. 19) separately.
  • Depending on the type of DBS receiver, there may be cases where some or all functions cannot be operated using the remote control.
  • It's not possible to operate a DBS receiver that is not equipped with a remote control sensor.
  • Though ECHOSTAR has a number of different remote codes, this remote control is applicable only to one of those codes preset at the factory.
  • It's not possible to set the remote control for both your DBS receiver and a cable box at the same time. You can only set the remote control to operate one of these units at a time.
JVC HM-HDS1U — OPERATE DBS RECEIVER 4 diagram (page 84)
Fig. 170

JVC (DISH Network) 51 ECHOSTAR (DISH Network) 51 PRIMESTAR 50 SONY (DSS) 41 RCA (DSS) 40

Page 85 of the JVC HM-HDS1U user manual — CONFIRM THE SETTING 6
Page 85 · click to enlarge
Page 85

Control Four JVC VCRs

SET REMOTE CONTROL CODE 2

The remote control is capable of controlling two JVC VCRs independently; one set to respond to your remote control's A code control signals and the other set to respond to B, C, D code control signals. The remote control is preset to send A code signals because your recorder is initially set to respond to A code signals. You can easily modify your recorder to respond to the other code signals. VCR A

Press and hold HDD on the remote control until “A” starts blinking on the display window of the remote control.

ENTER REMOTE CONTROL CODE 3

JVC HM-HDS1U — ENTER REMOTE CONTROL CODE 3 diagram (page 85)
Fig. 171

Press one of the following buttons to enter the desired cord, then press OK. The current setting code of the remote control appears on the display window.

2. sets the remote control code to “B” 3 : sets the remote control code to “C” 4 : sets the remote control code to “D” 1 : sets the remote control code to “A”

VCR C

Ex. When pressing 3.

PREPARE THE RECORDER FOR RECEIVING CONTROL CODE 4

1. To turn off the unit, press POWER on the front panel. 2) Press PLAY on the front panel for 5 seconds. The current setting code of the unit appears on the display.

A

TRANSMIT THE NEW CODE TO THE RECORDER 5

Press STOP on the remote control. The new code is transmitted to the unit and blinks for about 5 seconds on the display, then the clock time appears.

JVC HM-HDS1U — A diagram (page 85)
Fig. 172

CONFIRM THE SETTING 6

Press POWER on the remote control. When the unit is turned on, the setting is complete. If the unit is NOT turned on, repeat from step 1.

JVC HM-HDS1U — CONFIRM THE SETTING 6 diagram (page 85)
Fig. 173
Page 86 of the JVC HM-HDS1U user manual — SYMPTOM
Page 86 · click to enlarge
Page 86

86 EN TROUBLESHOOTING

Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your recorder off for repair.

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1. The power won’t come on.
  • The power cord is disconnected.

Connect the power cord.

2. The remote control won’t function.
  • The batteries are discharged.

Replace the dead batteries with new ones.

TAPE TRANSPORT

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1. The cassette gets stuck partway during loading, and is ejected.
  • The cassette was inserted incorrectly.

Make sure the cassette's window is facing up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards therecorder. Then insert the cassette.

PLAYBACK

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1. Playback won’t start.
  • HDD deck Playback point is at the end of the program.

Reverse the program by pressing appropriate buttons.

2. The tape is running but the picture won’t appear.
  • The TV receiver is set to the wrong mode.

Set the TV receiver to its AV mode.

3. Noise appears during visual search.
  • This is normal.
4. Breaks are noticeable in Hi-Fi soundtrack.
  • Automatic tracking is engaged.

Disengage Auto Tracking and adjust the tracking manually ( pg. 42).

5. The playback picture is blurred or interrupted, even though TV broadcasts are clear.
  • The video heads may be dirty.

The heads must be cleaned. Consult your JVC dealer.

6. The Hi-Fi soundtrack cannot be heard.
  • The soundtrack option was set incorrectly.

Press A. MONITOR to select "HI-FI" ( pg. 46).

RECORDING

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1. Recording won’t start.
  • VHS deck There is no cassette loaded, or the cassette loaded has had its Record Safety tab removed.

Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed.

2.Recording won’t stop.

  • HDD deck Live Memory Playback is in progress.

When Live Memory Playback is used, press STOP to stop Live Memory Playback, then press STOP to stop recording.

  • The recorder has been set to its AUX mode by mistake.

3.TV broadcasts won’t record properly.

Set the recorder to the appropriate channel.

4. Tape-to-tape editing won’t work.
  • The VCRs or the camcorder and the VCR have been incorrectly connected.

Refer to the directions and the illustration under “Edit To Or From Another VCR” ( pg. 78) or “Edit From A Camcorder” ( pg. 76) and properly connect the units. Make sure the power to all units is on.

  • The power to one or more of the units has not been turned on.
  • The recorder’s input mode has been set incorrectly.

Select the recorder’s appropriate input mode.

Page 87 of the JVC HM-HDS1U user manual — CONTINUED ON NEXT PAGE
Page 87 · click to enlarge
Page 87

RECORDING

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

5. Audio dubbing is not possible.
  • The tape speed had been set to LP at the original recording.
  • HDD deck This is normal. Audio dubbing is not available for HDD deck.

Set the tape speed to SP at the original recording.

7. When performing Tape Dubbing, the beginning of the dubbing start point is not dubbed.
  • This is normal.

TIMER RECORDING

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1. Timer recording won’t work.
  • The clock and/or the timer have been set incorrectly.
  • The timer is not engaged.

Set the clock and/or timer correctly.

Press TIMER and check to make sure that ‰ appears on the front display panel. Re-perform the set-up procedures. Make sure you have compensated for Guide Channel and recorder or cable box channel number mismatches ( pg. 56).

  • The recorder has not been set up properly.
2. Timer programming won’t work.
  • Timer recording is in progress.

Timer programming can’t be performed when timer recording is in progress. Wait until it finishes.

3. ‰ and ] on the front display panel won’t stop blinking.
  • The timer is engaged but there’s no cassette loaded.

VHS deck Load a cassette with the Record Safety tab intact, or cover the hole using adhesive tape.

4. The cassette is automatically ejected, and ‰ and ] on the front display panel won’t stop blinking.
  • VHS deck The loaded cassette has had its Record Safety tab removed.

Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the Record Safety tab intact. Remove the cassette and set the erase protection switch to “REC”.

5. ‰ blinks for 10 seconds and the timer mode is disengaged.
  • TIMER has been pressed when there are no programs in memory, or the timer record program information has not been programmed correctly.

Check the programmed data and re- program as necessary, then press TIMER again.

6. The cassette is automatically ejected, the power shuts off and ‰ and ] won’t stop blinking.
  • The end of tape was reached during timer recording.

The program may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire program.

CONTINUED ON NEXT PAGE

Page 88 of the JVC HM-HDS1U user manual — SYMPTOM
Page 88 · click to enlarge
Page 88

TROUBLESHOOTING (cont.)

TIMER RECORDING

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

7. Cable channels are not automatically switched during timer recording.
  • The Controller is not properly connected to the recorder.
  • The output channel selected in the Cable Box Set screen is incorrect.

Connect the Controller correctly ( pg. 15). After confirming your cable box’s output channel number, re-access the Cable Box Set screen and select the correct number ( pg. 16). Make sure the power is on before timer recording starts.

  • The cable box’s power is off.
8. Satellite channels are not automatically switched during timer recording.
  • The Controller is not properly connected to the recorder.
  • The output channel selected in the DBS Receiver Set screen is incorrect.

Connect the Controller correctly ( pg. 18). After confirming your DBS receiver’s output channel number, re-access the DBS Receiver Set screen and select the correct number ( pg. 19). Set the correct DBS Receiver brand code ( pg. 20). Make sure the power is on before timer recording starts.

  • The recorder is not set correctly to control the DBS Receiver.
  • The DBS receiver’s power is off.
9. Timer recording begins as scheduled, but the channel is always incorrect.
  • Even though you don't use an external Cable Box, “CABLE BOX SET” is set to “ON”.

Set "CABLE BOX SET" to "OFF" ( pg. 16).

10.We moved, and now the recorder Plus+ system doesn’t work properly.

  • The receivable stations in the new area are received on different channels than those in the previous area.

Re-perform the VCR Plus+ setup procedure ( pg. 54).

11.“PROGRAM FULL” is displayed on the screen.

  • All 16 programs are used.

Wait until a space in memory clears, or cancel unnecessary program information ( pg. 61).

OTHER PROBLEMS

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1. When scanning channels, some of them are skipped over.
  • Those channels have been preset to be skipped.

If you need the skipped channels, restore them ( pg. 14).

2. The channel can’t be changed.
  • Recording is in progress.

Press PAUSE to pause the recording, change channels, then press PLAY to resume recording.

3. The remote control won’t operate my TV or cable box or DBS receiver.
  • The remote control brand setting is incorrect.

Re-set the remote control to the correct brand ( pg. 82 or 83 or 84).

4. Even though Auto or Semi-Auto clock setting has been selected, the clock is incorrect.
  • The clock setting data received from the Host Channel is incorrect.

Select a different Host Channel during the Semi-Auto setting procedure ( pg. 11), or perform the Manual setting procedure ( pg. 12).

ATTENTION This recorder contains microcomputers. External electronic noise or interference can cause microcomputer to malfunction. If the recorder does not operate correctly switch its power off and unplug the power cord from the AC supply. Wait for a while and then plug the power back in. Eject and check the condition of the cassette. If everything appears normal resume operating the recorder as usual.

Page 89 of the JVC HM-HDS1U user manual — Q. During playback, on-screen operational indicators
Page 89 · click to enlarge
Page 89

EN 89 QUESTIONS AND ANSWERS

PLAYBACK

RECORDING

Q. What happens if the end of the tape is reached

Q. When I pause and then resume a recording, the end

during playback or search?

of the recording before the pause is overlapped by the new recording. Why does this happen? A. This is normal. It reduces distortion at the pause and

○ A. The tape is automatically rewound to the beginning.

○ resume points.

Q. Can the VCR indefinitely remain in the still mode? A. No. It stops automatically after 5 minutes (VHS deck)

○ to protect the heads.

Q. Can the VCR indefinitely remain in the Record-Pause

mode? A. No. The VCR automatically goes to its Stop mode

Q. During search, still and frame-by-frame playback,

after 5 minutes (VHS deck) to protect the heads. When paused during Instant Timer Recording (ITR), the VCR shuts off automatically after 5 minutes (VHS

the picture is intermittent. What’s the cause? A. Picture loss occurs when these types of playback are

attempted with a tape recorded in LP mode. Pressing PLAY to return to normal playback will restore the

○ deck).

○ picture.

Q. What happens if the tape runs out during recording? A. The VCR automatically rewinds it to the beginning.

Q. When returning from multi-speed search to normal

playback, the picture is disturbed. Should I be concerned about this?

TIMER RECORDING

○ A. No, it is normal.

Q. REC and ‰ remain lit on the front display panel. Is

there a problem? A. No. This is a normal condition for a timer recording

Q. When playing back programs that have been timer-

○ in progress.

recorded with consecutive times (such one program from 8:00 to 9:00 and another one from 9:00 to 10:00), the picture and sound become momentarily distorted at the point where the first program ends and the second program begins. Is this a malfunction?

Q. Can I program the timer while I’m watching a tape

or a TV broadcast? A. Yes, but while you are setting the timer you won't see

the tape's or broadcast program's picture as it is replaced by the on-screen menu. The audio from the tape or broadcast program will be present during the setting of the timer.

○ A. No. This is normal.

Q. Other than preventing further recording, what effect

does removing the safety tab have?

○ A. It disables marking of index codes.

Q. Sometimes, during Index Search, the VCR can’t find

the program I want to see. Why not?

○ A. There may be index codes too close together.

Q. During playback, on-screen operational indicators

sometimes jitter. Why does this happen? A. If the condition of the tape being played back is not

good, jittering of the video (including on-screen indicators) may occur.

Page 95 of the JVC HM-HDS1U user manual — SPECIFICATIONS
Page 95 · click to enlarge
Page 95

SPECIFICATIONS

GENERAL Power requirementAC 120 V ` , 60 Hz Power consumption
TUNER Tuning systemFrequency-synthesized tuner Channel coverage

Power on : 45 W Power off : 14 W Temperature Operating : 5°C to 40°C (41°F to 104°F) Storage : –20°C to 60°C (–4°F to 140°F) Operating position : Horizontal only Dimensions (WxHxD) : 435 mm x 124 mm x 385 mm

VHFChannels 2–13 UHF : Channels 14–69 CATV : 113 Channels
TIMER Clock referenceQuartz Program capacity : 1-year programmable timer/

(17-1/16" x 4-15/16" x 15-3/16") Weight : 7.4 kg (16.4 lbs) Input/Output : RCA connectors:

16 programs each on the VHS and HDD deck Memory backup time : Approx. 60 min.

(IN x 1, OUT x 2) S-Video connectors: (IN x 1, OUT x 2)

ACCESSORIES Provided accessoriesRF cable (F-type),
HDD DECK VIDEO/AUDIO Video formatMPEG2 (VBR) Audio format : MPEG1 Layer2

Infrared remote control unit, “AA” battery x 2, Audio/Video Cable, S-Video cable (4-pin), Controller

(SP)14 hours (LP) : 20 hours (EP) : 28 hours (SEP) : 40 hours

Specifications shown are for SP mode unless otherwise specified. E. & O.E. Design and specifications subject to change without notice.

VHS DECK VIDEO/AUDIO Signal systemNTSC-type colour signal and EIA

monochrome signal, 525 lines/ 60 fields Recording system : DA4 (Double Azimuth) head

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

helical scan system FormatS-VHS/VHS NTSC standard Signal-to-noise ratio : 45 dB Horizontal resolution : 240 lines (VHS)
400 lines (S-VHS) Frequency range70 Hz to 10,000 Hz

(Normal audio) 20 Hz to 20,000 Hz (Hi-Fi audio) Maximum recording time

(SP)210 min. with ST-210 video

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

cassette (EP)630 min. with ST-210 video

Maximum recording time · cassette

Page 96 of the JVC HM-HDS1U user manual — ACCESSORIES
Page 96 · click to enlarge
Page 96

FOR SERVICING (Only in U.S.A.)

HOW TO LOCATE YOUR JVC SERVICE CENTER

TOLL FREE: 1-800-252-5722

Dear customer: In order to receive the most satisfaction from your purchase, read the instruction booklet before operating the unit. In the event that repair is necessary, or for the address nearest your location, please refer to the factory service center list below or within the Continental United States, call 1-800-252-5722 for your authorized servicer. Remember to retain your Bill of Sale for Warranty Service.

http://www.jvcservice.com

— JVC

JVC SERVICE & ENGINEERING

COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP.

FACTORY SERVICE CENTER LOCATIONS

10 New Maple Avenue 1500 Lakes Parkway 705 Enterprise Street Pine Brook, NJ 07058-9641 Lawrenceville, GA 30243-5857 Aurora, IL 60504-8135 (973) 396-1000 (770) 339-2522 (630) 851-7855

5665 Corporate Avenue 10700 Hammerly Boulevard, Suite 110 2969 Mapunapuna Place, Suite 105 Cypress, CA 90630-4727 Houston, TX 77043-2310 Honolulu, HI 96819-2000 (714) 229-8011 (713) 935-9331 (808) 833-5828

13 Cummings Park 8192 W State Road 84 890 Dubuque Avenue Woburn, MA 01801-2105 Davie, FL 33324-4611 South San Francisco, CA 94080-1804 (781) 376-9100 (954) 472-1960 (650) 871-2666

Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of the wide array of JVC products, service is the key to maintaining the high level performance for which JVC is world famous. The JVC service and engineering organization stands behind our products.

NATIONAL HEADQUARTERS JVC SERVICE & ENGINEERING COMPANY OF AMERICA

DIVISION OF JVC AMERICAS CORP.

10 New Maple Avenue Pine Brook, NJ 07058-9641

Don't service it yourself.

If you ship the product...

Pack your JVC unit in the original carton or one of equivalent size and strength. Enclose, with the unit, a letter stating the problem or symptom that exists and also a copy of the receipt or bill of sale you received when you purchased your JVC unit. Print your home return address on the outside and the inside of the carton. Send to the appropriate JVC Factory Service Center as listed above.

ACCESSORIES

To purchase accessories for your JVC product, you may contact your local JVC Dealer. Or from the 48 Continental United States call toll free: 1-800-882-2345.

Page 97 of the JVC HM-HDS1U user manual — PARTS LABOR 1 YR 90 DAYS
Page 97 · click to enlarge
Page 97

WARRANTY (Only in U.S.A.)

LIMITED WARRANTY CONSUMER VIDEO 1-90

JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period as shown below. ("The Warranty Period")

PARTS LABOR 1 YR 90 DAYS

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN COMMONWEALTH OF PUERTO RICO.

WHAT WE WILL DO: If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered on an in-home basis.

WHAT YOU MUST DO FOR WARRANTY SERVICE: Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800) 252-5722. If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given to you by the toll-free number. If you have any questions concerning your JVC Product, please contact our Customer Relations Department.

WHAT IS NOT COVERED: This limited warranty provided by JVC does not cover: 1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service, or if affixed to any attachment not provided with the products, or if the model or serial number has been altered, tampered with, defaced or removed; 2. Initial installation and installation and removal for repair; 3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning; 4. Damage that occurs in shipment, due to act of God, and cosmetic damage; 5. Signal reception problems and failures due to line power surge; 6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase; 7. Accessories; 8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase); from the date of purchase);

There are no other express warranties except as listed above.

THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN. JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

JVC COMPANY OF AMERICA 1700 Valley Road DIVISION OF JVC AMERICAS CORP. Wayne, New Jersey 07470

REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.

For customer use:

Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this information for future reference.

Model No.: Serial No.:

Purchase dateName of dealer:
Page 98 of the JVC HM-HDS1U user manual — 98 EN MEMO
Page 98 · click to enlarge
Page 98

98 EN MEMO

Page 99 of the JVC HM-HDS1U user manual — EN 99 MEMO
Page 99 · click to enlarge
Page 99

EN 99 MEMO

Page 100 of the JVC HM-HDS1U user manual — VICTOR COMPANY OF JAPAN, LIMITED
Page 100 · click to enlarge
Page 100

HM-HDS1U

VICTOR COMPANY OF JAPAN, LIMITED

COPYRIGHT 2001 VICTOR COMPANY OF JAPAN, LTD. U Printed in Japan 0301 YSV*MW*VP

Ask about the JVC HM-HDS1U

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the JVC HM-HDS1U

Be the first to ask — other owners or our team will answer.

Original document

JVC HM-HDS1U manual PDF

100 pages·5.4 MB·MP3 Player·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…