Instruction/ maintenance manual of the product F5 Jura Capresso
Go to page of 26
IMPRESSA F50/F5/F505 Instructions for use 8/06 Art. Nr. 66381.
Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Tip JURA Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15 Fig.17 Fig. 5 Fig. 16.
Control elements 1. Rotary Switch 2. Illuminated ring 3. ON/OFF key 4. Programming key 5. Draw-off key 1 cup 6. Draw-off key 2 cups 7. Maintenance key 8. Steam pre-selection key 9. Display dialog system 10. Water tank with carrying handle 11. Filler funnel for pre-ground coffee: 12.
Contents 1. Safety information .......................................... page 6 1.1 Warning .............................................. page 6 1.2 Precautions .......................................... page 6 2. Preparing the IMPRESSA ............
6 Introduction Thank you for purchasing the IMPRESSA. To ensure perfect func- tioning of your IMPRESSA, carefully read this operating manual and keep it for future reference.
7 2.3 Fill water tank Only use fresh, cold water. Never fill in milk, mineral water or other liquids. Remove the water tank and rinse it with cold tap water thoroughly (Fig. 4). Then fill the water tank and reinstall it. Make sure to install the tank properly, it must engage audibly.
8 FILLING SYSTEM CLOSE TAP Close the steam / hot water draw-off tap (14). HEATING PRESS RINSE Press the maintenance key (7). Machine carries out a rinsing operation. RINSING READY If BEANS FILL is displayed, press the coffee draw-off key again.
9 5. Installation of CLARIS plus filter cartridges If the CLARIS plus filter cartridge is installed properly, de- scaling of the coffee machine is no longer required. For more information on the CLARIS plus filter cartridge refer to brochure «CLARIS plus.
10 Open the steam / hot water draw-off tap (14). HEATING READY 6. Rinsing the IMPRESSA When the IMPRESSA is switched off and has cooled down, a rinsing operation is started when the machine is switched on again. When the machine is switched off, a rinsing oper- ation is started automatically.
11 10. Drawing off pre-ground coffee Never use instant coffee or quick-coffee. We recommend that you always use powder from fresh coffee beans or, pre- ground, vacuum-packed coffee. Never fill in more than 2 portions of powder. The pre-ground coffee tank is no storage tank.
12 For Example: 210 ML POWDER Your product is being prepared. READY 11. Drawing off hot water If you do not change the settings using the Rotary Switch (1), the water quantity last adjusted will be drawn off auto- matically. Install the hot water nozzle (see Fig.
13 You can adjust the steam draw-off time individually by turning the Rotary Switch (1) until the required SEC are displayed. For example, 35 SEC If you do not change the steam draw-off ti.
14 During the steam draw-off operation, the message STEAM is displayed. When the steam quantity is reached, the message CLOSE TAP is displayed. Close the steam / hot water draw-off tap (14). STEAM READY At any time, you can stop dispensing steam at an earlier stage by closing the tap for dispensing steam/hot water (14).
15 As long as STEAM READY os on view in the display, the machine is ready to dispense steam. Fill the container with 2.5 dl of fresh water. Dip the milk pipe into the container with the fresh water. When READY appears in the display, press the steam prese- lect key (8) again to set the machine in readiness for the steam function.
16 READY Press programming key (4) until FILTER appears. The illuminated ring (2) is active. Turn the Rotary Switch (1) until Aroma is displayed.
17 Press the programming key (4) to quit the programming mode or select the next programming item using the Rotary Switch (1). READY If the machine is disconnected from power supply, the time must be programmed again. 15.6 Programming the automatic switch-on time You must programme the time (Chapter 15.
18 15.8 Cup counter You can check how many cups of the following coffee products were drawn off: a) 1 cup b) 2 cups c) Powder coffee READY Press programming key (4) until FILTER appears. The illuminated ring (2) is active. Turn the Rotary Switch (1) until CUPS MADE is displayed.
19 Press the Rotary Switch (1) e.g. 24H Select a setting of your choice. Press the Rotary Switch (1) to save the setting. DISPLAY Press the programming key (4) to quit the programming mode or select the next programming item using the Rotary Switch (1).
20 16.3 Drip tray missing NO – TRAY If this information is displayed, the drip tray (20) is not installed properly or was not installed at all. Insert the drip tray (20). READY 16.4 Fill coffee beans FILL BEANS Refill beans as described in Chapter 2.
21 16.9 Emptying the system Precondition: IMPRESSA switched off This operation is required to protect the IMPRESSA against frost damage during transports.
22 NO – TRAY Insert the tray again. SOLVENT IN TANK Completely dissolve the content of one blister (3 tablets) in a jug containing 0.5 litres of water, and fill the mixture in the water tank. Reinstall the water tank. OPEN TAP SOLVENT IN TANK Put a sufficiently large container under the hot water spout (Fig.
23 OPEN TAP Open the steam / hot water draw-off tap (14) (Fig. 13). DE-SCALING CLOSE TAP After you have closed the steam / hot water draw off tap (14), the following message is displayed DE-SCALING EMPTY TRAY Empty the tray NO – TRAY Insert the tray again.
24 21. Messages Cause Remedy FILL WATER Water tank is empty. Refill water Float defective Rinse or de-scale water tank FILL BEANS Bean tank is empty. Refill beans Although you have refilled beans, the Draw off a cup of coffee. The message will message still appears.
25 22. Problems Problem Cause Remedy Very loud noise coming from the Foreign body in grinding gear Drawing off pre-ground coffee still possible grinding gear Have IMPRESSA checked by JURA Service Too .
26 23. Legal information These operating instructions contain all the information required for using, operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained in these operating instructions is required for using the machine safely as well as for operational safety and safety during maintenance.
An important point after buying a device Jura Capresso F5 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jura Capresso F5 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jura Capresso F5 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jura Capresso F5 you will learn all the available features of the product, as well as information on its operation. The information that you get Jura Capresso F5 will certainly help you make a decision on the purchase.
If you already are a holder of Jura Capresso F5, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jura Capresso F5.
However, one of the most important roles played by the user manual is to help in solving problems with Jura Capresso F5. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jura Capresso F5 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
